Data Sheet
October 1, 2009
Austin SuperLynxTM 12V SMT Non-isolated Power Modules:
10Vdc – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 16A Output Current
* UL is a registered trademark of Underwriters Laboratories, Inc.
† CSA is a registered trademark of Canadian Standards Association.
‡ VDE is a trademark of Verband Deutscher Elektrotechniker e.V.
** ISO is a registered trademark of the International Organization of Standards
Document No: DS03-080 ver. 1.69
PDF name: superlynx_12v_smt_ds.pdf
Applications
Distributed power architectures
Intermediate bus voltage applications
Telecommunications equipment
Servers and storage applications
Networking equipment
Enterprise Networks
Latest generation IC’s (DSP, FPGA, ASIC)
and Microprocessor powered applications
Features
Compliant to RoHS EU Directive 2002/95/EC (-Z
versions)
Compliant to ROHS EU Directive 2002/95/EC with
lead solder exemption (non-Z versions)
Delivers up to 16A output current
High efficiency – 92% at 3.3V full load (VIN = 12.0V)
Small size and low profile:
33.0 mm x 13.46 mm x 8.28 mm
(1.30 in x 0.53 in x 0.326 in)
Low output ripple and noise
High Reliability:
Calculated MTBF = 4.4M hours at 25oC Full-load
Constant switching frequency (300 kHz)
Output voltage programmable from 0.75 Vdc to
5.5Vdc via external resistor
Line Regulation: 0.3% (typical)
Load Regulation: 0.4% (typical)
Temperature Regulation: 0.4 % (typical)
Remote On/Off
Remote Sense
Output overcurrent protection (non-latching)
Wide operating temperature range (-40°C to 85°C)
UL* 60950-1Recognized, CSA† C22.2 No. 60950-1-
03 Certified, and VDE‡ 0805:2001-12 (EN60950-1)
Licensed
ISO** 9001 and ISO 14001 certified manufacturing
facilities
Description
Austin SuperLynxTM 12V SMT (surface mount technology) power modules are non-isolated DC-DC converters that
can deliver up to 16A of output current with full load efficiency of 92% at 3.3V output. These modules provide a
precisely regulated output voltage ranging from 0.75Vdc to 5.5Vdc, programmable via an external resistor over a
wide range of input voltage (VIN = 10 – 14Vdc).
RoHS Compliant
Data Sheet
October 1, 2009
Austin SuperLynxTM 12V SMT Non-isolated Power Modules:
10 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 16A output current
LINEAGE POWER 2
Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are
absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in
excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for
extended periods can adversely affect the device reliability.
Parameter Device Symbol Min Max Unit
Input Voltage All VIN -0.3 15 Vdc
Continuous
Operating Ambient Temperature All TA -40 85 °C
(see Thermal Considerations section)
Storage Temperature All Tstg -55 125 °C
Electrical Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature
conditions.
Parameter Device Symbol Min Typ Max Unit
Operating Input Voltage VO,set ≤ VIN – 0.5V VIN 10.0 12.0 14.0 Vdc
Maximum Input Current All IIN,max 9.5 Adc
(VIN=10.0V to 14.0V, IO=IO, max )
Input No Load Current VO,set = 0.75 Vdc IIN,No load 40 mA
(VIN = 12.0Vdc, Io = 0, module enabled) VO,set = 5.0Vdc IIN,No load 100 mA
Input Stand-by Current All IIN,stand-by 2 mA
(VIN = 12.0Vdc, module disabled)
Inrush Transient All I2t 0.4 A2s
Input Reflected Ripple Current, peak-to-peak
(5Hz to 20MHz, 1μH source impedance; VIN, min to
VIN, max, IO= IOmax ; See Test configuration section)
All 30 mAp-p
Input Ripple Rejection (120Hz) All 30 dB
CAUTION: This power module is not internally fused. An input line fuse must always be used.
This power module can be used in a wide variety of applications, ranging from simple standalone operation to being
part of a complex power architecture. To preserve maximum flexibility, internal fusing is not included, however, to
achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-
acting fuse with a maximum rating of 15 A (see Safety Considerations section). Based on the information provided in
this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be
used. Refer to the fuse manufacturer’s data sheet for further information.
Data Sheet
October 1, 2009
Austin SuperLynxTM 12V SMT Non-isolated Power Modules:
10 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 16A output current
LINEAGE POWER 3
Electrical Specifications (continued)
Parameter Device Symbol Min Typ Max Unit
Output Voltage Set-point All VO, set -2.0 VO, set +2.0 % VO, set
(VIN=IN, min, IO=IO, max, TA=25°C)
Output Voltage All VO, set -2.5% ⎯ +3.5% % VO, set
(Over all operating input voltage, resistive load,
and temperature conditions until end of life)
Adjustment Range All VO 0.7525 5.5 Vdc
Selected by an external resistor
Output Regulation
Line (VIN=VIN, min to VIN, max) All
⎯ 0.3 ⎯ % VO, set
Load (IO=IO, min to IO, max) All
⎯ 0.4 ⎯ % VO, set
Temperature (Tref=TA, min to TA, max) All
⎯ 0.4 ⎯ % VO, set
Output Ripple and Noise on nominal output
(VIN=VIN, nom and IO=IO, min to IO, max
Cout = 1μF ceramic//10μFtantalum capacitors)
RMS (5Hz to 20MHz bandwidth) All ⎯ 12 30 mVrms
Peak-to-Peak (5Hz to 20MHz bandwidth) All ⎯ 30 75 mVpk-pk
External Capacitance
ESR ≥ 1 mΩ All CO, max ⎯ ⎯ 1000 μF
ESR ≥ 10 mΩ All CO, max ⎯ ⎯ 5000 μF
Output Current All Io 0 16 Adc
Output Current Limit Inception (Hiccup Mode ) All IO, lim ⎯ 180 ⎯ % Io
(VO= 90% of VO, set)
Output Short-Circuit Current All IO, s/c ⎯ 3 ⎯ Adc
(VO≤250mV) ( Hiccup Mode )
Efficiency VO,set = 0.75Vdc η 79.0 %
VIN= VIN, nom, TA=25°C VO, set = 1.2Vdc η 85.0 %
IO=IO, max , VO= VO,set V
O,set = 1.5Vdc η 87.0 %
V
O,set = 1.8Vdc η 88.0 %
V
O,set = 2.5Vdc η 90.5 %
V
O,set = 3.3Vdc η 92.0 %
V
O,set = 5.0Vdc η 94.0 %
Switching Frequency All fsw ⎯ 300 ⎯ kHz
Dynamic Load Response
(dIo/dt=2.5A/μs; VIN = VIN, nom; TA=25°C) All Vpk ⎯ 200 ⎯ mV
Load Change from Io= 50% to 100% of
Io,max; 1μF ceramic// 10 μF tantalum
Peak Deviation
Settling Time (Vo<10% peak deviation) All ts ⎯ 25 ⎯ μs
(dIo/dt=2.5A/μs; VIN = VIN, nom; TA=25°C) All Vpk ⎯ 200 ⎯ mV
Load Change from Io= 100% to 50%of Io,max:
1μF ceramic// 10 μF tantalum
Peak Deviation
Settling Time (Vo<10% peak deviation) All ts ⎯ 25 ⎯ μs
Data Sheet
October 1, 2009
Austin SuperLynxTM 12V SMT Non-isolated Power Modules:
10 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 16A output current
LINEAGE POWER 4
Electrical Specifications (continued)
Parameter Device Symbol Min Typ Max Unit
Dynamic Load Response
(dIo/dt=2.5A/μs; V VIN = VIN, nom; TA=25°C) All Vpk ⎯ 100 ⎯ mV
Load Change from Io= 50% to 100% of Io,max;
Co = 2x150 μF polymer capacitors
Peak Deviation
Settling Time (Vo<10% peak deviation) All ts ⎯ 50 ⎯ μs
(dIo/dt=2.5A/μs; VIN = VIN, nom; TA=25°C) All Vpk ⎯ 100 ⎯ mV
Load Change from Io= 100% to 50%of Io,max:
Co = 2x150 μF polymer capacitors
Peak Deviation
Settling Time (Vo<10% peak deviation) All ts ⎯ 50 ⎯ μs
General Specifications
Parameter Min Typ Max Unit
Calculated MTBF (IO=IO, max, TA=25°C) 4,444,000 Hours
Weight ⎯ 5.6 (0.2) ⎯ g (oz.)
Data Sheet
October 1, 2009
Austin SuperLynxTM 12V SMT Non-isolated Power Modules:
10 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 16A output current
LINEAGE POWER 5
Feature Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature
conditions. See Feature Descriptions for additional information.
Parameter Device Symbol Min Typ Max Unit
Remote On/Off Signal interface
(VIN=VIN, min to VIN, max; Open collector pnp or equivalent
Compatible, Von/off signal referenced to GND
See feature description section)
Logic High (On/Off Voltage pin open - Module ON)
Von/Off All VIH ― ― V
IN V
Ion/Off All IIH ― ― 10 μA
Logic Low (Von/Off ≤ 0.3V – Module OFF)
Von/Off All VIL ― ― 0.3 V
Ion/off All IIL ― ― 1 mA
Turn-On Delay and Rise Times
(IO=IO, max , VIN = VIN, nom, TA = 25 oC, )
Case 1: On/Off input is set to Logic Low (Module
ON) and then input power is applied (delay from
instant at which VIN =VIN, min until Vo=10% of Vo,set)
All Tdelay ― 3 ― msec
Case 2: Input power is applied for at least one second
and then the On/Off input is set to logic Low (delay from
instant at which Von/Off=0.3V until Vo=10% of Vo, set)
All Tdelay ― 3 ― msec
Output voltage Rise time (time for Vo to rise from 10%
of Vo,set to 90% of Vo, set)
All Trise ― 4 6 msec
Output voltage overshoot – Startup ― 1 % VO, set
IO= IO, max; VIN = 3.0 to 5.5Vdc, TA = 25 oC
Remote Sense Range ― ― 0.5
Overtemperature Protection All Tref ⎯ 125 ⎯ °C
(See Thermal Consideration section)
Input Undervoltage Lockout
Turn-on Threshold All 8.2 V
Turn-off Threshold All 8.0 V
Data Sheet
October 1, 2009
Austin SuperLynxTM 12V SMT Non-isolated Power Modules:
10 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 16A output current
LINEAGE POWER 6
Characteristic Curves
The following figures provide typical characteristics for the Austin SuperLynxTM 12V SMT modules at 25ºC.
70
72
74
76
78
80
82
84
86
88
90
0481216
Vin=14V
Vin=10V
Vin=12V
74
76
78
80
82
84
86
88
90
92
94
0481216
Vin=14V
Vin=10V
Vin=12V
EFFICIENCY, η (%)
OUTPUT CURRENT, IO (A)
EFFICIENCY, η (%)
OUTPUT CURRENT, IO (A)
Figure 1. Converter Efficiency versus Output Current
(Vout = 0.75Vdc).
Figure 4. Converter Efficiency versus Output Current
(Vout = 1.8Vdc).
70
72
74
76
78
80
82
84
86
88
90
04 81216
Vin=14V
Vin=10V
Vin=12V
74
76
78
80
82
84
86
88
90
92
94
0481216
Vin=14V
Vin=10V
Vin=12V
EFFICIENCY, η (%)
OUTPUT CURRENT, IO (A)
EFFICIENCY, η (%)
OUTPUT CURRENT, IO (A)
Figure 2. Converter Efficiency versus Output Current
(Vout = 1.2Vdc).
Figure 5. Converter Efficiency versus Output Current
(Vout = 2.5Vdc).
72
74
76
78
80
82
84
86
88
90
92
04 81216
Vin=14V
Vin=10V
Vin=12V
74
76
78
80
82
84
86
88
90
92
94
96
0481216
Vin=14V
Vin=10V
Vin=12V
EFFICIENCY, η (%)
OUTPUT CURRENT, IO (A)
EFFICIENCY, η (%)
OUTPUT CURRENT, IO (A)
Figure 3. Converter Efficiency versus Output Current
(Vout = 1.5Vdc).
Figure 6. Converter Efficiency versus Output Current
(Vout = 3.3Vdc).
Data Sheet
October 1, 2009
Austin SuperLynxTM 12V SMT Non-isolated Power Modules:
10 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 16A output current
LINEAGE POWER 7
Characteristic Curves (continued)
The following figures provide typical characteristics for the Austin SuperLynxTM 12V SMT modules at 25ºC.
0
2
4
6
8
10
12
8 9 10 11 12 13 14
Io =0A
Io =16A
Io =8A
INPUT CURRENT, IIN (A)
INPUT VOLTAGE, VIN
(
V
)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (2A/div) VO (V) (200mV/div)
TIME
,
t
(
5
μ
s/div
)
Figure 7. Input voltage vs. Input Current
(Vout = 5.0Vdc).
Figure 10. Transient Response to Dynamic Load
Change from 50% to 100% of full load (Vo = 5.0Vdc).
OUTPUT VOLTAGE
VO (V) (20mV/div)
TIME, t (2μs/div)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (2A/div) VO (V) (200mV/div)
TIME, t (5 μs/div)
Figure 8. Typical Output Ripple and Noise
(Vin = 12V dc, Vo = 2.5 Vdc, Io=16A).
Figure 11. Transient Response to Dynamic Load
Change from 100% to 50% of full load (Vo = 5.0 Vdc).
OUTPUT VOLTAGE
VO (V) (20mV/div)
TIME, t (2μs/div)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (2A/div) VO (V) (50mV/div)
TIME, t (10μs/div)
Figure 9. Typical Output Ripple and Noise
(Vin = 12V dc, Vo = 5.0 Vdc, Io=16A).
Figure 12. Transient Response to Dynamic Load
Change from 50% to 100% of full load (Vo = 5.0 Vdc,
Cext = 2x150 μF Polymer Capacitors).
Data Sheet
October 1, 2009
Austin SuperLynxTM 12V SMT Non-isolated Power Modules:
10 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 16A output current
LINEAGE POWER 8
Characteristic Curves (continued)
The following figures provide typical characteristics for the Austin SuperLynxTM 12V SMT modules at 25ºC.
OUTPUT CURRENT OUTPUTVOLTAGE
IO (A) (2A/div) VO (V) (100mV/div)
TIME, t (10μs/div)
OUTPUT VOLTAGE, INPUT VOLTAGE
Vo (V) (2V/div) VIN (V) (5V/div)
TIME, t (2 ms/div)
Figure 13. Transient Response to Dynamic Load
Change from 100% of 50% full load (Vo = 5.0 Vdc, Cext
= 2x150
μ
F Pol
y
mer Ca
p
acitors
)
.
Figure 16. Typical Start-Up with application of Vin with
low-ESR polymer capacitors at the output (7x150 μF)
(
Vin = 12Vdc
,
Vo = 5.0Vdc
,
Io = 16A
,
Co = 1050
μ
F
)
.
OUTPUT VOLTAGE On/Off VOLTAGE
VOV) (2V/div) VOn/off (V) (5V/div)
TIME, t (2 ms/div)
OUTPUT VOLTAGE
VOV) (1V/div)
TIME, t (2 ms/div)
Figure 14. Typical Start-Up Using Remote On/Off
(Vin = 12Vdc, Vo = 5.0Vdc, Io =16A).
Figure 17 Typical Start-Up with Prebias (Vin = 12Vdc,
Vo = 5.0Vdc, Io = 1A, Vbias =3.3 Vdc).
OUTPUT VOLTAGE On/Off VOLTAGE
VOV) (2V/div) VOn/off (V) (5V/div)
TIME, t (2 ms/div)
OUTPUT CURRENT,
IO (A) (10A/div)
TIME, t (10ms/div)
Figure 15. Typical Start-Up Using Remote On/Off with
Low-ESR external capacitors (7x150uF Polymer)
(Vin = 12Vdc, Vo = 5.0Vdc, Io = 16A, Co = 1050μF).
Figure 18. Output short circuit Current (Vin = 12Vdc,
Vo = 0.75Vdc).
Data Sheet
October 1, 2009
Austin SuperLynxTM 12V SMT Non-isolated Power Modules:
10 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 16A output current
LINEAGE POWER 9
Characteristic Curves (continued)
The following figures provide thermal derating curves for the Austin SuperLynxTM 12V SMT modules.
0
2
4
6
8
10
12
14
16
18
20 30 40 50 60 70 80 90
100 LFM
200 LFM
NC
300 LFM
400 LFM 0
2
4
6
8
10
12
14
16
18
20 30 40 50 60 70 80 90
100 LFM
200 LFM
NC
300 LFM
400 LFM
OUTPUT CURRENT, Io (A)
AMBIENT TEMPERATURE, TA OC
OUTPUT CURRENT, Io (A)
AMBIENT TEMPERATURE, TA OC
Figure 19. Derating Output Current versus Local
Ambient Temperature and Airflow (Vin = 12Vdc,
Vo=0.75Vdc).
Figure 22. Derating Output Current versus Local
Ambient Temperature and Airflow (Vin = 12Vdc,
Vo=5.0 Vdc).
0
2
4
6
8
10
12
14
16
18
20 30 40 50 60 70 80 90
100 LFM
200 LFM
NC
300 LFM
400 LFM
OUTPUT CURRENT, Io (A)
AMBIENT TEMPERATURE, TA OC
Figure 20. Derating Output Current versus Local
Ambient Temperature and Airflow (Vin = 12Vdc,
Vo=1.8 Vdc).
0
2
4
6
8
10
12
14
16
18
20 30 40 50 60 70 80 90
100 LFM
200 LFM
NC
300 LFM
400 LFM
OUTPUT CURRENT, Io (A)
AMBIENT TEMPERATURE, T
A
O
C
Figure 21. Derating Output Current versus Local
Ambient Temperature and Airflow (Vin = 12Vdc,
Vo=3.3 Vdc).
Data Sheet
October 1, 2009
Austin SuperLynxTM 12V SMT Non-isolated Power Modules:
10 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 16A output current
LINEAGE POWER 10
Test Configurations
TO OSCILLOSCOPE CURRENT PROBE
LTEST
1μH
BATTERY
CS 1000μF
Electrolytic
E.S.R.<0.1Ω
@ 20°C 100kHz
2x100μF
Tantalum
VIN(+)
COM
NOTE: Measure input reflected ripple current with a simulated
source inductance (LTEST) of 1μH. Capacitor CS offsets
possible battery impedance. Measure current as shown
above.
CIN
Figure 23. Input Reflected Ripple Current Test Setup.
NOTE: All voltage measurements to be taken at the module
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
V
O
(+)
COM
1uF .
RESISTIVE
LOAD
SCOPE
COPPER STRIP
GROUND PLANE
10uF
Figure 24. Output Ripple and Noise Test Setup.
VO
COM
VIN(+)
COM
RLOAD
Rcontact Rdistribution
Rcontact Rdistribution
Rcontact
Rcontact
Rdistribution
Rdistribution
VIN VO
NOTE: All voltage measurements to be taken at the module
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
Figure 25. Output Voltage and Efficiency Test Setup.
η =
VO. IO
VIN. IIN
x 100 %
Efficiency
Design Considerations
Input Filtering
The Austin SuperLynxTM 12V SMT module should be
connected to a low-impedance source. A highly inductive
source can affect the stability of the module. An input
capacitance must be placed directly adjacent to the input
pin of the module, to minimize input ripple voltage and
ensure module stability.
In a typical application, 6x47 µF low-ESR tantalum
capacitors (AVX part #: TPSE476M025R0100, 47µF 25V
100 mΩ ESR tantalum capacitor) will be sufficient to
provide adequate ripple voltage at the input of the
module. To further minimize ripple voltage at the input,
very low ESR ceramic capacitors are recommended at
the input of the module. Figure 26 shows input ripple
voltage (mVp-p) for various outputs with 6x47 µF
tantalum capacitors and with 6x22 µF ceramic capacitor
(TDK part #: C4532X5R1C226M) at full load. .
Input Ripple Voltage (mVp-p)
0
50
10 0
15 0
200
250
300
350
0123456
Tantalum
Ceramic
Output Voltage (Vdc)
Figure 26. Input ripple voltage for various output
with 6x47 µF tantalum capacitors and with 6x22 µF
ceramic capacitors at the input (full load).
Data Sheet
October 1, 2009
Austin SuperLynxTM 12V SMT Non-isolated Power Modules:
10 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 16A output current
LINEAGE POWER 11
Design Considerations (continued)
Output Filtering
The Austin SuperLynxTM 12V SMT module is designed for
low output ripple voltage and will meet the maximum
output ripple specification with 1 µF ceramic and 10 µF
tantalum capacitors at the output of the module.
However, additional output filtering may be required by
the system designer for a number of reasons. First, there
may be a need to further reduce the output ripple and
noise of the module. Second, the dynamic response
characteristics may need to be customized to a particular
load step change.
To reduce the output ripple and improve the dynamic
response to a step load change, additional capacitance at
the output can be used. Low ESR polymer and ceramic
capacitors are recommended to improve the dynamic
response of the module. For stable operation of the
module, limit the capacitance to less than the maximum
output capacitance as specified in the electrical
specification table.
Safety Considerations
For safety agency approval the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standards,
i.e., UL 60950-1, CSA C22.2 No. 60950-1-03, and VDE
0850:2001-12 (EN60950-1) Licensed.
For the converter output to be considered meeting the
requirements of safety extra-low voltage (SELV), the
input must meet SELV requirements. The power module
has extra-low voltage (ELV) outputs when all inputs are
ELV.
The input to these units is to be provided with a fast-
acting fuse with a maximum rating of 15A in the positive
input lead.
Data Sheet
October 1, 2009
Austin SuperLynxTM 12V SMT Non-isolated Power Modules:
10 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 16A output current
LINEAGE POWER 12
Feature Description
Remote On/Off
The Austin SuperLynxTM 12V SMT power modules
feature an On/Off pin for remote On/Off operation of the
module. If not using the remote On/Off pin, leave the pin
open (module will be On). The On/Off pin signal
(Von/Off) is referenced to ground. To switch the module
on and off using remote On/Off, connect an open
collector pnp transistor between the On/Off pin and the
VIN pin (See Figure 27).
During a logic-high (On/Off pin is pulled high internal to
the module) when the transistor is in the Off state, the
power module is ON. The maximum allowable leakage
current of the transistor when Von/off = VIN,max is 10µA.
During a logic-low when the transistor is turned-on, the
power module is OFF. During this state VOn/Off is less
than 0.3V and the maximum IOn/Off = 1mA.
VIN(+)
GND
Ion/off
Von/off
Enable
20k
20k
20k
20k
On/Of
f
+
-
Css
Figure 27. Remote On/Off Implementation.
Overcurrent Protection
To provide protection in a fault (output overload)
condition, the unit is equipped with internal
current-limiting circuitry and can endure current limiting
continuously. At the point of current-limit inception, the
unit enters hiccup mode. The unit operates normally once
the output current is brought back into its specified range.
The typical average output current during hiccup is 3A.
Input Undervoltage Lockout
At input voltages below the input undervoltage lockout
limit, module operation is disabled. The module will begin
to operate at an input voltage above the undervoltage
lockout turn-on threshold.
Overtemperature Protection
To provide protection in a fault condition, the unit is
equipped with a thermal shutdown circuit. The unit will
shutdown if the thermal reference point Tref, exceeds
125oC (typical), but the thermal shutdown is not
intended as a guarantee that the unit will survive
temperatures beyond its rating. The module will
automatically restarts after it cools down.
Output Voltage Programming
The output voltage of the Austin SuperLynxTM 12V can
be programmed to any voltage from 0.75Vdc to 5.5Vdc
by connecting a resistor (shown as Rtrim in Figure 28)
between the Trim and GND pins of the module.
Without an external resistor between the Trim and
GND pins, the output of the module will be 0.7525Vdc.
To calculate the value of the trim resistor, Rtrim for a
desired output voltage, use the following equation:
Ω
⎥
⎦
⎤
⎢
⎣
⎡−
−
=1000
7525.0
10500
Vo
Rtrim
Rtrim is the external resistor in Ω
Vo is the desired output voltage
For example, to program the output voltage of the Austin
SuperLynxTM 12V module to 1.8V, Rtrim is calculated as
follows:
⎥
⎦
⎤
⎢
⎣
⎡−
−
=1000
75.08.1
10500
Rtrim
Ω= kRtrim 024.9
VO(+)
TRIM
GND
LOAD
VIN(+)
ON/OFF
Rtrim
Figure 28. Circuit configuration to program output
voltage using an external resistor.
Austin SuperLynxTM 12Vdc can also be programmed by
applying a voltage between the TRIM and GND pins
(Figure 29). The following equation can be used to
determine the value of Vtrim needed to obtain a desired
output voltage Vo:
{}()
7525.00667.07.0 −×−= VoVtrim
For example, to program the output voltage of a
SuperLynxTM module to 3.3 Vdc, Vtrim is calculated as
follows:
{}
)7525.03.30667.07.0( −×−=Vtrim
VVtrim 530.0=
Data Sheet
October 1, 2009
Austin SuperLynxTM 12V SMT Non-isolated Power Modules:
10 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 16A output current
LINEAGE POWER 13
Feature Descriptions (continued)
Output Voltage Programming (continued)
V
O
(+)
TRIM
GND
V
trim
LOAD
V
IN
(+)
ON/OFF
+
-
Figure 29. Circuit Configuration for programming
Output voltage using external voltage source.
Table 1 provides Rtrim values for some common
output voltages, while Table 2 provides values of
the external voltage source, Vtrim for same
common output voltages.
Table 1
VO, set (V) Rtrim (KΩ)
0.7525 Open
1.2 22.46
1.5 13.05
1.8 9.024
2.5 5.009
3.3 3.122
5.0 1.472
Table 2
VO, set (V) Vtrim (V)
0.7525 Open
1.2 0.670
1.5 0.650
1.8 0.630
2.5 0.583
3.3 0.530
5.0 0.4166
By using a 1% tolerance trim resistor, set point tolerance
of ±2% is achieved as specified in the electrical
specification. The POL Programming Tool, available at
www.lineagepower.com under the Design Tools section,
helps determine the required external trim resistor
needed for a specific output voltage.
The amount of power delivered by the module is defined
as the voltage at the output terminals multiplied by the
output current. When using the trim feature, the output
voltage of the module can be increased, which at the
same output current would increase the power output of
the module. Care should be taken to ensure that the
maximum output power of the module remains at or
below the maximum rated power (Pmax = Vo,set x Io,max).
Voltage Margining
Output voltage margining can be implemented in the
Austin SuperLynxTM 12V SMT modules by connecting a
resistor, Rmargin-up, from the Trim pin to the ground pin for
margining-up the output voltage and by connecting a
resistor, Rmargin-down, from the Trim pin to the Output pin
for margining-down. Figure 30 shows the circuit
configuration for output voltage margining. The POL
Programming Tool, available at www.lineagepower.com
under the Design Tools section, also calculates the
values of Rmargin-up and Rmargin-down for a specific output
voltage and % margin. Please consult your local
Lineage Power technical representative for additional
details.
Vo
Austin Lynx or
Lynx II Series
GND
Trim
Q1
Rtrim
Rmargin-up
Q2
Rmargin-down
Figure 30. Circuit Configuration for margining Output
voltage.
Data Sheet
October 1, 2009
Austin SuperLynxTM 12V SMT Non-isolated Power Modules:
10 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 16A output current
LINEAGE POWER 14
Feature Descriptions (continued)
Remote Sense
The Austin SuperLynxTM 12V 12V SMTpower modules
have a Remote Sense feature to minimize the effects of
distribution losses by regulating the voltage at the
Remote Sense pin (See Figure 31). The voltage between
the Sense pin and Vo pin must not exceed 0.5V.
The amount of power delivered by the module is defined
as the output voltage multiplied by the output current (Vo
x Io). When using Remote Sense, the output voltage of
the module can increase, which if the same output is
maintained, increases the power output by the module.
Make sure that the maximum output power of the module
remains at or below the maximum rated power. When
the Remote Sense feature is not being used, connect the
Remote Sense pin to output pin.
VO
COM
VIN(+)
COM
RLOAD
Rcontact Rdistribution
Rcontact Rdistribution
Rcontact
Rcontact
Rdistribution
Rdistribution
Sense
Figure 31. Remote sense circuit configuration.
Data Sheet
October 1, 2009
Austin SuperLynxTM 12V SMT Non-isolated Power Modules:
10 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 16A output current
LINEAGE POWER 15
Thermal Considerations
Power modules operate in a variety of thermal
environments; however, sufficient cooling should always
be provided to help ensure reliable operation.
Considerations include ambient temperature, airflow,
module power dissipation, and the need for increased
reliability. A reduction in the operating temperature of the
module will result in an increase in reliability. The thermal
data presented here is based on physical measurements
taken in a wind tunnel. The test set-up is shown in Figure
33. Note that the airflow is parallel to the short axis of the
module as shown in figure 32. The derating data applies
to airflow in either direction of the module’s short axis.
Air Flow
Tref
Top View
Bottom View
Figure 32. Tref Temperature measurement location.
The thermal reference point, Tref used in the
specifications is shown in Figure 32. For reliable
operation this temperature should not exceed 115oC.
The output power of the module should not exceed the
rated power of the module (Vo,set x Io,max).
Please refer to the Application Note “Thermal
Characterization Process For Open-Frame Board-
Mounted Power Modules” for a detailed discussion of
thermal aspects including maximum device temperatures.
Figure 33. Thermal Test Set-up.
Heat Transfer via Convection
Increased airflow over the module enhances the heat
transfer via convection. Thermal derating curves
showing the maximum output current that can be
delivered at different local ambient temperature (TA) for
airflow conditions ranging from natural convection and
up to 2m/s (400 ft./min) are shown in the
Characteristics Curves section.
A
ir
flow
x
Po w e r M o d u le
W
ind Tunnel
PWBs
5.97_
(0.235)
76.2_
(3.0)
Probe Location
for measuring
airflow and
ambient
temperature
25.4_
(1.0)
Data Sheet
October 1, 2009
Austin SuperLynxTM 12V SMT Non-isolated Power Modules:
10 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 16A output current
LINEAGE POWER 16
Mechanical Outline
Dimensions are in millimeters and (inches).
Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated]
x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.)
Data Sheet
October 1, 2009
Austin SuperLynxTM 12V SMT Non-isolated Power Modules:
10 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 16A output current
LINEAGE POWER 17
Recommended Pad Layout
Dimensions are in millimeters and (inches).
Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated]
x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.)
Name Pin No. Function
ON/OFF 1 Remote On/Off Control
Vin 2 Positive Input Voltage
GND 4 Common Ground
Vout 5 Positive Output Voltage
TRIM 6 Output Voltage Trim
SENSE 7 Positive Remote Sense
Data Sheet
October 1, 2009
Austin SuperLynxTM 12V SMT Non-isolated Power Modules:
10 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 16A output current
LINEAGE POWER 18
Packaging Details
The Austin SuperLynxTM 12V SMTversion is supplied in tape & reel as standard. Modules are shipped in quantities
of 250 modules per reel.
All Dimensions are in millimeters and (in inches).
Reel Dimensions
Outside diameter: 330.2 mm (13.00)
Inside diameter: 177.8 mm (7.00”)
Tape Width: 44.0 mm (1.73”)
Data Sheet
October 1, 2009
Austin SuperLynxTM 12V SMT Non-isolated Power Modules:
10 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 16A output current
LINEAGE POWER 19
Surface Mount Information
Pick and Place
The Austin SuperLynxTM 12V SMT modules use an
open frame construction and are designed for a fully
automated assembly process. The modules are fitted
with a label designed to provide a large surface area
for pick and place operations. The label meets all the
requirements for surface mount processing, as well as
safety standards, and is able to withstand reflow
temperatures of up to 300oC. The label also carries
product information such as product code, serial
number and the location of manufacture.
Figure 34. Pick and Place Location.
Nozzle Recommendations
The module weight has been kept to a minimum by
using open frame construction. Even so, these
modules have a relatively large mass when compared
to conventional SMT components. Variables such as
nozzle size, tip style, vacuum pressure and placement
speed should be considered to optimize this process.
The minimum recommended nozzle diameter for
reliable operation is 6mm. The maximum nozzle outer
diameter, which will safely fit within the allowable
component spacing, is 9 mm.
Oblong or oval nozzles up to 11 x 9 mm may also be
used within the space available.
Reflow Soldering Information
The Austin SuperLynxTM 12V SMT power modules
are large mass, low thermal resistance devices and
typically heat up slower than other SMT components.
It is recommended that the customer review data
sheets in order to customize the solder reflow profile
for each application board assembly. The following
instructions must be observed when soldering these
units. Failure to observe these instructions may result
in the failure of or cause damage to the modules, and
can adversely affect long-term reliability.
Typically, the eutectic solder melts at 183oC, wets the
land, and subsequently wicks the device connection.
Sufficient time must be allowed to fuse the plating on
the connection to ensure a reliable solder joint. There
are several types of SMT reflow technologies
currently used in the industry. These surface mount
power modules can be reliably soldered using natural
forced convection, IR (radiant infrared), or a
combination of convection/IR. For reliable soldering
the solder reflow profile should be established by
accurately measuring the modules pin temperatures.
Figure 35. Reflow Profile.
An example of a reflow profile (using 63/37 solder) for
the Austin SuperLynxTM 12V SMT power module is :
• Pre-heating zone: room temperature to 183oC
(2.0 to 4.0 minutes maximum)
• Initial ramp rate < 2.5oC per second
• Soaking Zone: 155
oC to 183 oC – 60 to 90
seconds typical (2.0 minutes maximum)
• Reflow zone ramp rate:1.3oC to 1.6oC per second
• Reflow zone: 210oC to 235oC peak temperature –
30 to 60 seconds (90 seconds maximum
Data Sheet
October 1, 2009
Austin SuperLynxTM 12V SMT Non-isolated Power Modules:
10 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 16A output current
LINEAGE POWER 20
Surface Mount Information (continued)
Lead Free Soldering
The –Z version Austin SuperLynx 12V SMT modules
are lead-free (Pb-free) and RoHS compliant and are
both forward and backward compatible in a Pb-free
and a SnPb soldering process. Failure to observe the
instructions below may result in the failure of or cause
damage to the modules and can adversely affect
long-term reliability.
Pb-free Reflow Profile
Power Systems will comply with J-STD-020 Rev. C
(Moisture/Reflow Sensitivity Classification for
Nonhermetic Solid State Surface Mount Devices) for
both Pb-free solder profiles and MSL classification
procedures. This standard provides a recommended
forced-air-convection reflow profile based on the
volume and thickness of the package (table 4-2). The
suggested Pb-free solder paste is Sn/Ag/Cu (SAC).
The recommended linear reflow profile using
Sn/Ag/Cu solder is shown in Figure. 36.
MSL Rating
The Austin SuperLynx 12V SMT modules have a MSL
rating of 2.
Storage and Handling
The recommended storage environment and handling
procedures for moisture-sensitive surface mount
packages is detailed in J-STD-033 Rev. A (Handling,
Packing, Shipping and Use of Moisture/Reflow
Sensitive Surface Mount Devices). Moisture barrier
bags (MBB) with desiccant are required for MSL
ratings of 2 or greater. These sealed packages
should not be broken until time of use. Once the
original package is broken, the floor life of the product
at conditions of <= 30°C and 60% relative humidity
varies according to the MSL rating (see J-STD-033A).
The shelf life for dry packed SMT packages will be a
minimum of 12 months from the bag seal date, when
stored at the following conditions: < 40° C, < 90%
relative humidity.
Post Solder Cleaning and Drying
Considerations
Post solder cleaning is usually the final circuit-board
assembly process prior to electrical board testing. The
result of inadequate cleaning and drying can affect
both the reliability of a power module and the
testability of the finished circuit-board assembly. For
guidance on appropriate soldering, cleaning and
drying procedures, refer to Board Mounted Power
Modules: Soldering and Cleaning Application Note
(AN04-001).
Per J-STD-020 Rev. C
0
50
100
150
200
250
300
Reflow Time (Seconds)
Reflow Temp (°C)
Heating Zone
1°C/Second
Peak Temp 260°C
* Min. Time Above 235°C
15 Seconds
*Time Above 217°C
60 Seconds
Cooling
Zone
Figure 36. Recommended linear reflow profile
using Sn/Ag/Cu solder.
Data Sheet
October 1, 2009
Austin SuperLynxTM 12V SMT Non-isolated Power Modules:
10 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 16A output current
LINEAGE POWER 21
Document No: DS03-080 ver. 1.69
PDF name: superlynx_12v_smt_ds.pdf
Ordering Information
Please contact your Lineage Power Sales Representative for pricing, availability and optional features.
Table 3. Device Codes
Device Code
Input
Voltage
Range
Output
Voltage
Output
Current
Efficiency
3.3V @ 16A
Connector
Type
Comcodes
AXA016A0X3-SR 10 – 14Vdc 0.75V – 5.5Vdc 16 A 92.0% SMT 108982661
AXA016A0X3-SRZ 10 – 14Vdc 0.75V – 5.5Vdc 16 A 92.0% SMT CC109104840
AXA016A0X3-SR12* 10 – 14Vdc 0.75V – 5.5Vdc 16 A 92.0% SMT 108993424
AXA016A0X3-SR12Z* 10 – 14Vdc 0.75V – 5.5Vdc 16 A 92.0% SMT CC109104485
* -12 code has 100Ω resistor between sense and output pins, internal to the module. Standard code, without –12
suffix, has 10Ω resistor between sense and output pins.
-Z refers to RoHS compliant codes
World Wide Headquarters
Lineage Power Corporation
601 Shiloh Road, Plano, TX 75074, USA
+1-800-526-7819
(Outside U.S.A.: +1-972-244-9428)
www.lineagepower.com
e-mail: techsupport1@lineagepower.com
Asia-Pacific Headquarters
Tel: +65 6593 7211
Europe, Middle-East and Africa Headquarters
Tel: +49 898 780 672 80
India Headquarters
Tel: +91 80 28411633
Lineage Powe r reserves the right to make change s to the product(s) or information conta ined herein without notice. No liability is assumed as a result of their use or
a
pplication. No rights under any patent accompany the sale of any such product(s) or information.
Lineage Power DC-DC products are protected unde r various patents. Information on these patents is available at www.lineagepower.com/patents.
©
2009 Linea
g
e Power Cor
p
oration
,
(
Plano
,
Texas
)
All Inte rnational Ri
g
hts Reserved.
