SCAN921025H,SCAN921226H SCAN921025H and SCAN921226H High Temperature 20-80 MHz 10 Bit Bus LVDS SerDes with IEEE 1149.1 (JTAG) and at-speed BIST Literature Number: SNLS185B SCAN921025H and SCAN921226H High Temperature 20-80 MHz 10 Bit Bus LVDS SerDes with IEEE 1149.1 (JTAG) and at-speed BIST General Description The SCAN921025H transforms a 10-bit wide parallel LVCMOS/LVTTL data bus into a single high speed Bus LVDS serial data stream with embedded clock. The SCAN921226H receives the Bus LVDS serial data stream and transforms it back into a 10-bit wide parallel data bus and recovers parallel clock. Both devices are compliant with IEEE 1149.1 Standard for Boundary Scan Test. IEEE 1149.1 features provide the design or test engineer access via a standard Test Access Port (TAP) to the backplane or cable interconnects and the ability to verify differential signal integrity. The pair of devices also features an at-speed BIST mode which allows the interconnects between the Serializer and Deserializer to be verified at-speed. The SCAN921025H transmits data over backplanes or cable. The single differential pair data path makes PCB design easier. In addition, the reduced cable, PCB trace count, and connector size tremendously reduce cost. Since one output transmits clock and data bits serially, it eliminates clock-to-data and data-to-data skew. The powerdown pin saves power by reducing supply current when not using either device. Upon power up of the Serializer, you can choose to activate synchronization mode or allow the Deserializer to use the synchronization-to-random-data feature. By using the synchronization mode, the Deserializer will establish lock to a signal within specified lock times. In addition, the embedded clock guarantees a transition on the bus every 12-bit cycle. This eliminates transmission errors due to charged cable conditions. Furthermore, you may put the SCAN921025H output pins into TRI-STATE to achieve a high impedance state. The PLL can lock to frequencies between 20 MHz and 80 MHz. Features n High Temperature Operation to 125C n IEEE 1149.1 (JTAG) Compliant and At-Speed BIST test mode. n Clock recovery from PLL lock to random data patterns. n Guaranteed transition every data transfer cycle n Chipset (Tx + Rx) power consumption < 600 mW (typ) @ 80 MHz n Single differential pair eliminates multi-channel skew n 800 Mbps serial Bus LVDS data rate (at 80 MHz clock) n 10-bit parallel interface for 1 byte data plus 2 control bits n Synchronization mode and LOCK indicator n Programmable edge trigger on clock n High impedance on receiver inputs when power is off n Bus LVDS serial output rated for 27 load n Small 49-lead BGA package Applications n Automotive n Industrial n Military/Aerospace Block Diagrams 20120701 (c) 2005 National Semiconductor Corporation DS201207 www.national.com SCAN921025H and SCAN921226H High Temperature 20-80 MHz 10 Bit BLVDS SerDes with IEEE 1149.1 (JTAG) and at-speed BIST December 2005 SCAN921025H and SCAN921226H Block Diagrams (Continued) Application 20120702 non-repetitive data patterns. However, the transmission of SYNC patterns enables the Deserializer to lock to the Serializer signal within a specified time. See Figure 16. The user's application determines control of the SYNC1 and SYNC 2 pins. One recommendation is a direct feedback loop from the LOCK pin. Under all circumstances, the Serializer stops sending SYNC patterns after both SYNC inputs return low. When the Deserializer detects edge transitions at the Bus LVDS input, it will attempt to lock to the embedded clock information. When the Deserializer locks to the Bus LVDS clock, the LOCK output will go low. When LOCK is low, the Deserializer outputs represent incoming Bus LVDS data. Functional Description The SCAN921025H and SCAN921226H are a 10-bit Serializer and Deserializer chipset designed to transmit data over differential backplanes at clock speeds from 20 to 80 MHz. The chipset is also capable of driving data over Unshielded Twisted Pair (UTP) cable. The chipset has three active states of operation: Initialization, Data Transfer, and Resynchronization; and two passive states: Powerdown and TRI-STATE. In addition to the active and passive states, there are also test modes for JTAG access and at-speed BIST. The following sections describe each operation and passive state and the test modes. Data Transfer Initialization After initialization, the Serializer will accept data from inputs DIN0-DIN9. The Serializer uses the TCLK input to latch incoming Data. The TCLK_R/F pin selects which edge the Serializer uses to strobe incoming data. TCLK_R/F high selects the rising edge for clocking data and low selects the falling edge. If either of the SYNC inputs is high for 5*TCLK cycles, the data at DIN0-DIN9 is ignored regardless of clock edge. After determining which clock edge to use, a start and stop bit, appended internally, frame the data bits in the register. The start bit is always high and the stop bit is always low. The start and stop bits function as the embedded clock bits in the serial stream. The Serializer transmits serialized data and clock bits (10+2 bits) from the serial data output (DO ) at 12 times the TCLK frequency. For example, if TCLK is 80 MHz, the serial rate is 80 x 12 = 960 Mega-bits-per-second. Since only 10 bits are from input data, the serial "payload" rate is 10 times the TCLK frequency. For instance, if TCLK = 80 MHz, the payload data rate is 80 x 10 = 800 Mbps. The data source provides TCLK and must be in the range of 20 MHz to 80 MHz nominal. The Serializer outputs (DO ) can drive a point-to-point connection or in limited multi-point or multi-drop backplanes. The outputs transmit data when the enable pin (DEN) is Initialization of both devices must occur before data transmission begins. Initialization refers to synchronization of the Serializer and Deserializer PLL's to local clocks, which may be the same or separate. Afterwards, synchronization of the Deserializer to Serializer occurs. Step 1: When you apply VCC to both Serializer and/or Deserializer, the respective outputs enter TRI-STATE, and on-chip power-on circuitry disables internal circuitry. When VCC reaches VCCOK (2.5V) the PLL in each device begins locking to a local clock. For the Serializer, the local clock is the transmit clock (TCLK) provided by the source ASIC or other device. For the Deserializer, you must apply a local clock to the REFCLK pin. The Serializer outputs remain in TRI-STATE while the PLL locks to the TCLK. After locking to TCLK, the Serializer is now ready to send data or SYNC patterns, depending on the levels of the SYNC1 and SYNC2 inputs or a data stream. The SYNC pattern sent by the Serializer consists of six ones and six zeros switching at the input clock rate. Note that the Deserializer LOCK output will remain high while its PLL locks to the incoming data or to SYNC patterns on the input. Step 2: The Deserializer PLL must synchronize to the Serializer to complete initialization. The Deserializer will lock to www.national.com 2 ing more than one potential position for clocking bits. Upon detection, the circuitry will prevent the LOCK output from becoming active until the potential "false lock" pattern changes. The false lock detect circuitry expects the data will eventually change, causing the Deserializer to lose lock to the data pattern and then continue searching for clock bits in the serial data stream. Graphical representations of RMT are shown in Figure 1. Please note that RMT only applies to bits DIN0-DIN8. (Continued) high, PWRDN = high, and SYNC1 and SYNC2 are low. When DEN is driven low, the Serializer output pins will enter TRI-STATE. When the Deserializer synchronizes to the Serializer, the LOCK pin is low. The Deserializer locks to the embedded clock and uses it to recover the serialized data. ROUT data is valid when LOCK is low. Otherwise ROUT0-ROUT9 is invalid. Powerdown The ROUT0-ROUT9 pins use the RCLK pin as the reference to data. The polarity of the RCLK edge is controlled by the RCLK_R/F input. See Figure 13. ROUT(0-9), LOCK and RCLK outputs will drive a maximum of three CMOS input gates (15 pF load) with a 80 MHz clock. When no data transfer occurs, you can use the Powerdown state. The Serializer and Deserializer use the Powerdown state, a low power sleep mode, to reduce power consumption. The Deserializer enters Powerdown when you drive PWRDN and REN low. The Serializer enters Powerdown when you drive PWRDN low. In Powerdown, the PLL stops and the outputs enter TRI-STATE, which disables load current and reduces supply current to the milliampere range. To exit Powerdown, you must drive the PWRDN pin high. Before valid data exchanges between the Serializer and Deserializer, you must reinitialize and resynchronize the devices to each other. Initialization of the Serializer takes 510 TCLK cycles. The Deserializer will initialize and assert LOCK high until lock to the Bus LVDS clock occurs. Resynchronization When the Deserializer PLL locks to the embedded clock edge, the Deserializer LOCK pin asserts a low. If the Deserializer loses lock, the LOCK pin output will go high and the outputs (including RCLK) will enter TRI-STATE. The user's system monitors the LOCK pin to detect a loss of synchronization. Upon detection, the system can arrange to pulse the Serializer SYNC1 or SYNC2 pin to resynchronize. Multiple resynchronization approaches are possible. One recommendation is to provide a feedback loop using the LOCK pin itself to control the sync request of the Serializer (SYNC1 or SYNC2). Dual SYNC pins are provided for multiple control in a multi-drop application. Sending sync patterns for resynchronization is desirable when lock times within a specific time are critical. However, the Deserializer can lock to random data, which is discussed in the next section. TRI-STATE The Serializer enters TRI-STATE when the DEN pin is driven low. This puts both driver output pins (DO+ and DO-) into TRI-STATE. When you drive DEN high, the Serializer returns to the previous state, as long as all other control pins remain static (SYNC1, SYNC2, PWRDN, TCLK_R/F). When you drive the REN pin low, the Deserializer enters TRI-STATE. Consequently, the receiver output pins (ROUT0-ROUT9) and RCLK will enter TRI-STATE. The LOCK output remains active, reflecting the state of the PLL. Random Lock Initialization and Resynchronization The initialization and resynchronization methods described in their respective sections are the fastest ways to establish the link between the Serializer and Deserializer. However, the SCAN921226H can attain lock to a data stream without requiring the Serializer to send special SYNC patterns. This allows the SCAN921226H to operate in "open-loop" applications. Equally important is the Deserializer's ability to support hot insertion into a running backplane. In the open loop or hot insertion case, we assume the data stream is essentially random. Therefore, because lock time varies due to data stream characteristics, we cannot possibly predict exact lock time. However, please see Table 1 for some general random lock times under specific conditions. The primary constraint on the "random" lock time is the initial phase relation between the incoming data and the REFCLK when the Deserializer powers up. As described in the next paragraph, the data contained in the data stream can also affect lock time. If a specific pattern is repetitive, the Deserializer could enter "false lock" - falsely recognizing the data pattern as the clocking bits. We refer to such a pattern as a repetitive multi-transition, RMT. This occurs when more than one LowHigh transition takes place in a clock cycle over multiple cycles. This occurs when any bit, except DIN 9, is held at a low state and the adjacent bit is held high, creating a 0-1 transition. In the worst case, the Deserializer could become locked to the data pattern rather than the clock. Circuitry within the SCAN921226H can detect that the possibility of "false lock" exists. The circuitry accomplishes this by detect- TABLE 1. Random Lock Times for the SCAN921226H 80 MHz Units Maximum 18 s Mean 3.0 s Minimum 0.43 s Conditions: PRBS 215, VCC = 3.3V 1) Difference in lock times are due to different starting points in the data pattern with multiple parts. Test Modes In addition to the IEEE 1149.1 test access to the digital TTL pins, the SCAN921025H and SCAN921226H have two instructions to test the LVDS interconnects. The first is EXTEST. This is implemented at LVDS levels and is only intended as a go no-go test (e.g. missing cables). The second method is the RUNBIST instruction. It is an "at-systemspeed" interconnect test. It is executed in approximately 28mS with a system clock speed of 80MHz. There are two bits in the RX BIST data register for notification of PASS/ FAIL and TEST_COMPLETE. Pass indicates that the BER (Bit-Error-Rate) is better than 10-7. An important detail is that once both devices have the RUNBIST instruction loaded into their respective instruction registers, both devices must move into the RTI state within 4K 3 www.national.com SCAN921025H and SCAN921226H Data Transfer SCAN921025H and SCAN921226H Test Modes Ordering Information (Continued) system clocks (At a SCLK of 66Mhz and TCK of 1MHz this allows for 66 TCK cycles). This is not a concern when both devices are on the same scan chain or LSP, however, it can be a problem with some multi-drop devices. This test mode has been simulated and verified using National's SCANSTA111. NSID Function Package SCAN921025HSM Serializer SLC49a SCAN921226HSM Deserializer SLC49a 20120724 20120725 DIN0 Held Low-DIN1 Held High Creates an RMT Pattern DIN4 Held Low-DIN5 Held High Creates an RMT Pattern 20120726 DIN8 Held Low-DIN9 Held High Creates an RMT Pattern FIGURE 1. RMT Patterns Seen on the Bus LVDS Serial Output www.national.com 4 Supply Voltage (VCC) ja ESD Rating -0.3V to +4V LVCMOS/LVTTL Input Voltage LVCMOS/LVTTL Output Voltage MM -0.3V to (VCC +0.3V) -0.3V to +3.9V Bus LVDS Driver Output Voltage -0.3V to +3.9V Bus LVDS Output Short Circuit Duration Recommended Operating Conditions 10mS Junction Temperature +150C Storage Temperature -65C to +150C Lead Temperature (Soldering, 4 seconds) +220C Min Nom Max Units Supply Voltage (VCC) 3.0 3.3 3.6 V Operating Free Air Temperature (TA) -40 +25 +125 C 2.4 V 100 mVP-P Receiver Input Range Maximum Package Power Dissipation Capacity 0 Supply Noise Voltage (VCC) @ 25C Package: 49L BGA > 2kV > 250V HBM -0.3V to (VCC +0.3V) Bus LVDS Receiver Input Voltage 85C/W 1.47 W Package Derating: 11.8 mW/C above +25C 49L BGA Electrical Characteristics Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions Min Typ Max Units SERIALIZER LVCMOS/LVTTL DC SPECIFICATIONS (apply to DIN0-9, TCLK, PWRDN, TCLK_R/F, SYNC1, SYNC2, DEN) VIH High Level Input Voltage 2.0 VIL Low Level Input Voltage VCL Input Clamp Voltage ICL = -18 mA IIN Input Current VIN = 0V or 3.6V VCC GND -10 V 0.8 V -0.86 -1.5 V 1 +10 A DESERIALIZER LVCMOS/LVTTL DC SPECIFICATIONS (apply to pins PWRDN, RCLK_R/ F, REN, REFCLK = inputs; apply to pins ROUT, RCLK, LOCK = outputs) VIH High Level Input Voltage 2.0 VCC V VIL Low Level Input Voltage GND 0.8 V VCL Input Clamp Voltage -1.5 V ICL = -18 mA -0.62 IIN Input Current VIN = 0V or 3.6V -10 1 +15 A VOH High Level Output Voltage IOH = -9 mA 2.2 3.0 VCC V VOL Low Level Output Voltage IOL = 9 mA GND 0.25 0.5 V IOS Output Short Circuit Current VOUT = 0V -15 -47 -85 mA IOZ TRI-STATE Output Current PWRDN or REN = 0.8V, VOUT = 0V or VCC -10 0.1 +10 A 200 290 SERIALIZER Bus LVDS DC SPECIFICATIONS (apply to pins DO+ and DO-) VOD Output Differential Voltage (DO+)-(DO-) VOD Output Differential Voltage Unbalance VOS Offset Voltage VOS Offset Voltage Unbalance IOS Output Short Circuit Current D0 = 0V, DIN = High,PWRDN and DEN = 2.4V IOZ TRI-STATE Output Current PWRDN or DEN = 0.8V, DO = 0V or VCC -10 IOX Power-Off Output Current VCC = 0V, DO=0V or 3.6V -20 RL = 27, Figure 17 mV 35 1.05 5 mV 1.1 1.3 V 4.8 35 mV -56 -90 mA 1 1 +10 A +30 A www.national.com SCAN921025H and SCAN921226H Absolute Maximum Ratings (Note 1) SCAN921025H and SCAN921226H Electrical Characteristics (Continued) Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions Min Typ Max Units +6 +50 mV -50 -12 VIN = +2.4V, VCC = 3.6V or 0V -10 VIN = 0V, VCC = 3.6V or 0V -10 1 0.05 DESERIALIZER Bus LVDS DC SPECIFICATIONS (apply to pins RI+ and RI-) VTH Differential Threshold High Voltage VTL Differential Threshold Low Voltage IIN Input Current VCM = +1.1V mV +10 A +10 A mA SERIALIZER SUPPLY CURRENT (apply to pins DVCC and AVCC) ICCD ICCXD Serializer Supply Current RL = 27 f = 20 MHz 45 60 Worst Case Figure 2 f = 80 MHz 90 105 mA 0.2 2.0 mA Serializer Supply Current Powerdown PWRDN = 0.8V, f = 80MHz DESERIALIZER SUPPLY CURRENT (apply to pins DVCC and AVCC) ICCR ICCXR Deserializer Supply Current CL = 15 pF f = 20 MHz 50 75 mA Worst Case Figure 3 f = 80 MHz 100 120 mA Deserializer Supply Current Powerdown PWRDN = 0.8V, REN = 0.8V 0.36 1.0 mA SCAN CIRCUITRY DC SPECIFICATIONS, SERIALIZER AND DESERIALIZER (applies to SCAN pins as noted) VIH High Level Input Voltage VCC = 3.0 to 3.6V, pins TCK, TMS, TDI, and TRST 2.0 VCC V VIL Low Level Input Voltage VCC = 3.0 to 3.6V, pins TCK, TMS, TDI, and TRST GND 0.8 V VCL Input Clamp Voltage VCC = 3.0V, ICL = -18 mA, pins TCK, TMS, TDI, and TRST -0.85 -1.5 V IIH Input Current VCC = 3.6V, VIN = 3.6V, pins TCK, TMS, TDI, and TRST 1 +10 A IIL Input Current VCC = 3.6V, VIN = 0.0V, TCK Input -10 -1 A IILR Input Current VCC = 3.6V, VIN = 0V, pins TMS, TDI, and TRST -20 -10 A VOH High Level Output Voltage VCC = 3.0V, IOH = -12 mA, TDO output 2.2 VOL Low Level Output Voltage VCC = 3.0V, IOL = 12 mA, TDO output IOS Output Short Circuit Current VCC = 3.6V, VOUT = 0.0V, TDO output IOZ TRI-STATE Output Current PWRDN or REN = 0.8V, VOUT = 0V or VCC 2.6 V 0.3 0.5 V -15 -90 -120 mA -10 0 +10 A Serializer Timing Requirements for TCLK Over recommended operating supply and temperature ranges unless otherwise specified. Min Typ Max Units tTCP Symbol Transmit Clock Period Parameter Conditions 12.5 T 50.0 ns tTCIH Transmit Clock High Time 0.4T 0.5T 0.6T ns tTCIL Transmit Clock Low Time 0.4T 0.5T 0.6T ns tCLKT TCLK Input Transition Time 3 6 ns tJIT TCLK Input Jitter 150 ps (RMS) Typ Max Units 0.2 0.4 ns 0.25 0.4 ns Serializer Switching Characteristics Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter tLLHT Bus LVDS Low-to-High Transition Time tLHLT Bus LVDS High-to-Low Transition Time www.national.com Conditions Min RL = 27 CL=10pF to GND Figure 4 (Note 4) 6 (Continued) Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions tDIS DIN (0-9) Setup to TCLK tDIH DIN (0-9) Hold from TCLK tHZD DO HIGH to TRI-STATE Delay tLZD DO LOW to TRI-STATE Delay tZHD Min RL = 27, CL=10pF to GND Figure 7 Typ Max Units 0 ns 4.0 ns RL = 27, CL=10pF to GND Figure 8 (Note 5) 3 10 ns 3 10 ns DO TRI-STATE to HIGH Delay 5 10 ns tZLD DO TRI-STATE to LOW Delay 6.5 10 ns tSPW SYNC Pulse Width tPLD RL = 27 Serializer PLL Lock Time Figure 10 510*tTCP tSD Serializer Delay tTCP+ 1.0 tDJIT Deterministic Jitter tRJIT 5*tTCP RL = 27, Figure 11 RL = 27, CL=10pF to GND, (Note 6) Random Jitter 20MHz ns 513*tTCP ns tTCP+ 3.5 ns 140 ps -40 +60 ps 6 10 ps (RMS) tTCP+ 2.5 -330 -130 80MHz Deserializer Timing Requirements for REFCLK Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Min Typ Max Units 12.5 T 50.0 ns REFCLK Duty Cycle 30 50 70 % tRFCP / tTCP Ratio of REFCLK to TCLK 95 1 105 tRFTT REFCLK Transition Time 3 6 Typ Max Units 50.0 ns 1.2 4 ns 1.1 4 ns tRFCP REFCLK Period tRFDC Conditions ns Deserializer Switching Characteristics Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions tRCP Receiver out Clock Period tCLH CMOS/TTL CL = 15 pF Low-to-High Transition Figure 5 Time tCHL tDD tROS tRCP = tTCP Figure 11 Pin/Freq. Min RCLK 12.5 Rout(0-9), LOCK, RCLK CMOS/TTL High-to-Low Transition Time Deserializer Delay Figure 12 ROUT Data Valid before RCLK 1.75*tRCP+1.25 1.75*tRCP+5.0 1.75*tRCP+8.5 ns Room Temp, 3.3V All Temp, All Freq 20MHz 1.75*tRCP+2.25 1.75*tRCP+5.0 1.75*tRCP+8.0 ns Room Temp, 3.3V 80MHz 1.75*tRCP+2.25 1.75*tRCP+5.0 1.75*tRCP+8.0 ns RCLK 20MHz 0.4*tRCP 0.5*tRCP ns RCLK 80MHz 0.35*tRCP 0.5*tRCP ns 20MHz -0.4*tRCP -0.5*tRCP ns 80MHz -0.35*tRCP -0.5*tRCP 45 50 Figure 13 tROH ROUT Data Valid after Figure 13 RCLK tRDC RCLK Duty Cycle 7 ns 55 % www.national.com SCAN921025H and SCAN921226H Serializer Switching Characteristics SCAN921025H and SCAN921226H Deserializer Switching Characteristics (Continued) Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Typ Max Units 2.8 10 ns LOW to TRI-STATE Delay 2.8 10 ns tZHR TRI-STATE to HIGH Delay 4.2 10 ns tZLR TRI-STATE to LOW Delay 4.2 10 ns tDSR1 Deserializer PLL Lock Time from PWRDWN (with SYNCPAT) 20MHz 1.7 3.5 s 80MHz 1.0 2.5 s 20MHz 0.65 1.5 s 80MHz 0.29 0.8 s LOCK 3.7 12 ns tHZR HIGH to TRI-STATE Delay tLZR tDSR2 Deserializer PLL Lock time from SYNCPAT tZHLK TRI-STATE to HIGH Delay (power-up) tRNMI-R Ideal Noise Margin Right Figure 20 Conditions Figure 14 Pin/Freq. Min Rout(0-9) Figure 15 Figure 16 (Note 7) VCC = 3.15 to 3.6V VCC = 3.0V +335 80MHz +215 20MHz tRNMI-L Ideal Noise Margin Left VCC = 3.15 to 3.6V Figure 20 VCC = 3.0V +1 -395 80MHz ns ps -520 20MHz ps -1 ns SCAN Circuitry Timing Requirements Symbol Parameter Conditions Min Typ RL = 500, CL = 35 pF 25.0 50.0 Max Units fMAX Maximum TCK Clock Frequency tS TDI to TCK, H or L 1.0 tH TDI to TCK, H or L 2.0 ns tS TMS to TCK, H or L 2.5 ns tH TMS to TCK, H or L 1.5 ns tW TCK Pulse Width, H or L 10.0 ns tW TRST Pulse Width, L 2.5 ns tREC Recovery Time, TRST to TCK 2.0 ns MHz ns Note 1: "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The table of "Electrical Characteristics" specifies conditions of device operation. Note 2: Typical values are given for VCC = 3.3V and TA = +25C. Note 3: Current into device pins is defined as positive. Current out of device pins is defined as negative. Voltages are referenced to ground except VOD, VOD, VTH and VTL which are differential voltages. Note 4: tLLHT and tLHLT specifications are Guaranteed By Design (GBD) using statistical analysis. Note 5: Because the Serializer is in TRI-STATE mode, the Deserializer will lose PLL lock and have to resynchronize before data transfer. Note 6: tDJIT specifications are Guaranteed By Design using statistical analysis. Note 7: For the purpose of specifying deserializer PLL performance, tDSR1 and tDSR2 are specified with the REFCLK running and stable, and with specific conditions for the incoming data stream (SYNCPATs). It is recommended that the derserializer be initialized using either tDSR1 timing or tDSR2 timing. tDSR1 is the time required for the deserializer to indicate lock upon power-up or when leaving the power-down mode. Synchronization patterns should be sent to the device before initiating either condition. tDSR2 is the time required to indicate lock for the powered-up and enabled deserializer when the input (RI+ and RI-) conditions change from not receiving data to receiving synchronization patterns (SYNCPATs). Note 8: tRNM is a measure of how much phase noise (jitter) the deserializer can tolerate in the incoming data stream before bit errors occur. The Deserializer Noise Margin is Guaranteed By Design (GBD) using statistical analysis. www.national.com 8 SCAN921025H and SCAN921226H AC Timing Diagrams and Test Circuits 20120703 FIGURE 2. "Worst Case" Serializer ICC Test Pattern 20120704 FIGURE 3. "Worst Case" Deserializer ICC Test Pattern 20120705 FIGURE 4. Serializer Bus LVDS Output Load and Transition Times 20120706 FIGURE 5. Deserializer CMOS/TTL Output Load and Transition Times 9 www.national.com SCAN921025H and SCAN921226H AC Timing Diagrams and Test Circuits (Continued) 20120707 FIGURE 6. Serializer Input Clock Transition Time 20120708 Timing shown for TCLK_R/F = LOW FIGURE 7. Serializer Setup/Hold Times 20120709 FIGURE 8. Serializer TRI-STATE Test Circuit and Timing www.national.com 10 SCAN921025H and SCAN921226H AC Timing Diagrams and Test Circuits (Continued) 20120710 FIGURE 9. Serializer PLL Lock Time, and PWRDN TRI-STATE Delays 20120723 FIGURE 10. SYNC Timing Delays 20120711 FIGURE 11. Serializer Delay 11 www.national.com SCAN921025H and SCAN921226H AC Timing Diagrams and Test Circuits (Continued) 20120712 FIGURE 12. Deserializer Delay 20120713 Timing shown for RCLK_R/F = LOW Duty Cycle (tRDC) = FIGURE 13. Deserializer Data Valid Out Times 20120714 FIGURE 14. Deserializer TRI-STATE Test Circuit and Timing www.national.com 12 SCAN921025H and SCAN921226H AC Timing Diagrams and Test Circuits (Continued) 20120715 FIGURE 15. Deserializer PLL Lock Times and PWRDN TRI-STATE Delays 20120722 FIGURE 16. Deserializer PLL Lock Time from SyncPAT 13 www.national.com SCAN921025H and SCAN921226H AC Timing Diagrams and Test Circuits (Continued) 20120716 VOD = (DO+)-(DO-). Differential output signal is shown as (DO+)-(DO-), device in Data Transfer mode. FIGURE 17. VOD Diagram www.national.com 14 USING THE SCAN921025H AND SCAN921226H The Serializer and Deserializer chipset is an easy to use transmitter and receiver pair that sends 10 bits of parallel LVTTL data over a serial Bus LVDS link up to 800 Mbps. An on-board PLL serializes the input data and embeds two clock bits within the data stream. The Deserializer uses a separate reference clock (REFCLK) and an onboard PLL to extract the clock information from the incoming data stream and then deserialize the data. The Deserializer monitors the incoming clock information, determines lock status, and asserts the LOCK output high when loss of lock occurs. The Deserializer can relock to the incoming data stream by making the Serializer resend SYNC patterns, as described above, or by random locking, which can take more time, depending on the data patterns being received. HOT INSERTION All the BLVDS devices are hot pluggable if you follow a few rules. When inserting, ensure the Ground pin(s) makes contact first, then the VCC pin(s), and then the I/O pins. When removing, the I/O pins should be unplugged first, then the VCC, then the Ground. Random lock hot insertion is illustrated in Figure 21. POWER CONSIDERATIONS An all CMOS design of the Serializer and Deserializer makes them inherently low power devices. In addition, the constant current source nature of the Bus LVDS outputs minimizes the slope of the speed vs. ICC curve of conventional CMOS designs. PCB CONSIDERATIONS The Bus LVDS Serializer and Deserializer should be placed as close to the edge connector as possible. In multiple Deserializer applications, the distance from the Deserializer to the slot connector appears as a stub to the Serializer driving the backplane traces. Longer stubs lower the impedance of the bus, increase the load on the Serializer, and lower the threshold margin at the Deserializers. Deserializer devices should be placed much less than one inch from slot connectors. Because transition times are very fast on the Serializer Bus LVDS outputs, reducing stub lengths as much as possible is the best method to ensure signal integrity. POWERING UP THE DESERIALIZER The SCAN921226H can be powered up at any time by following the proper sequence. The REFCLK input can be running before the Deserializer powers up, and it must be running in order for the Deserializer to lock to incoming data. The Deserializer outputs will remain in TRI-STATE until the Deserializer detects data transmission at its inputs and locks to the incoming data stream. TRANSMITTING DATA Once you power up the Serializer and Deserializer, they must be phase locked to each other to transmit data. Phase locking occurs when the Deserializer locks to incoming data or when the Serializer sends patterns. The Serializer sends SYNC patterns whenever the SYNC1 or SYNC2 inputs are high. The LOCK output of the Deserializer remains high until it has locked to the incoming data stream. Connecting the LOCK output of the Deserializer to one of the SYNC inputs of the Serializer will guarantee that enough SYNC patterns are sent to achieve Deserializer lock. The Deserializer can also lock to incoming data by simply powering up the device and allowing the "random lock" circuitry to find and lock to the data stream. While the Deserializer LOCK output is low, data at the Deserializer outputs (ROUT0-9) is valid, except for the specific case of loss of lock during transmission which is further discussed in the "Recovering from LOCK Loss" section below. TRANSMISSION MEDIA The Serializer and Deserializer can also be used in point-topoint configuration of a backplane, through a PCB trace, or through twisted pair cable. In point-to-point configuration, the transmission media need only be terminated at the receiver end. Please note that in point-to-point configuration, the potential of offsetting the ground levels of the Serializer vs. the Deserializer must be considered. Also, Bus LVDS provides a +/- 1.2V common mode range at the receiver inputs. FAILSAFE BIASING FOR THE SCAN921226H The SCAN921226H has an improved input threshold sensitivity of +/- 50mV versus +/- 100mV for the DS92LV1210 or DS92LV1212. This allows for greater differential noise margin in the SCAN921226H. However, in cases where the receiver input is not being actively driven, the increased sensitivity of the SCAN921226H can pickup noise as a signal and cause unintentional locking. For example, this can occur when the input cable is disconnected. External resistors can be added to the receiver circuit board to prevent noise pick-up. Typically, the non-inverting receiver input is pulled up and the inverting receiver input is pulled down by high value resistors. the pull-up and pull-down resistors (R1 and R2) provide a current path through the termination resistor (RL) which biases the receiver inputs when they are not connected to an active driver. The value of the pull-up and pull-down resistors should be chosen so that enough current is drawn to provide a +15mV drop across the termination resistor. Please see Figure 18 for the Failsafe Biasing Setup. NOISE MARGIN The Deserializer noise margin is the amount of input jitter (phase noise) that the Deserializer can tolerate and still reliably receive data. Various environmental and systematic factors include: Serializer: TCLK jitter, VCC noise (noise bandwidth and out-of-band noise) Media: ISI, Large VCM shifts Deserializer: VCC noise RECOVERING FROM LOCK LOSS In the case where the Deserializer loses lock during data transmission, up to 3 cycles of data that were previously received can be invalid. This is due to the delay in the lock detection circuit. The lock detect circuit requires that invalid 15 www.national.com SCAN921025H and SCAN921226H clock information be received 4 times in a row to indicate loss of lock. Since clock information has been lost, it is possible that data was also lost during these cycles. Therefore, after the Deserializer relocks to the incoming data stream and the Deserializer LOCK pin goes low, at least three previous data cycles should be suspect for bit errors. Application Information SCAN921025H and SCAN921226H Application Information Please refer to Figure 19 and Figure 20 for a graphic representation of tDJIT and tRNM. Also, for a more detailed explanation of tRNM, please see the Application Note titled 'How to Validate BLVDS SER/DES Signal Integrity Using an Eye Mask'. (Continued) USING tDJIT AND tRNM TO VALIDATE SIGNAL QUALITY The parameter tRNM is calculated by first measuring how much of the ideal bit the receiver needs to ensure correct sampling. After determining this amount, what remains of the ideal bit that is available for external sources of noise is called tRNM. tRNM includes transmitter jitter. The vertical limits of the mask are determined by the SCAN921226H receiver input threshold of +/- 50mV. 20120727 FIGURE 18. Failsafe Biasing Setup 20120729 FIGURE 19. Deterministic Jitter and Ideal Bit Position www.national.com 16 SCAN921025H and SCAN921226H Application Information (Continued) 20120728 tRNMI-L is the ideal noise margin on the left of the figure, it is a negative value to indicate early with respect to ideal. tRNMI-R is the ideal noise margin on the right of the above figure, it is a positive value to indicate late with respect to ideal. FIGURE 20. Ideal Deserializer Noise Margin (tRNMI) and Sampling Window 20120717 FIGURE 21. Random Lock Hot Insertion 17 www.national.com SCAN921025H and SCAN921226H Pin Diagrams SCAN921025HSM - Serializer (Top View) 20120730 SCAN921226HSM - Deserializer (Top View) 20120731 www.national.com 18 Pin Name I/O Ball Id. Description DIN I A3, B1, C1, D1, D2, D3, E1, E2, F2, F4 Data Input. LVTTL levels inputs. Data on these pins are loaded into a 10-bit input register. TCLKR/F I G3 Transmit Clock Rising/Falling strobe select. LVTTL level input. Selects TCLK active edge for strobing of DIN data. High selects rising edge. Low selects falling edge. DO+ O D7 + Serial Data Output. Non-inverting Bus LVDS differential output. DO- O D5 - Serial Data Output. Inverting Bus LVDS differential output. DEN I D6 Serial Data Output Enable. LVTTL level input. A low puts the Bus LVDS outputs in TRI-STATE. PWRDN I C7 Powerdown. LVTTL level input. PWRDN driven low shuts down the PLL and TRI-STATEs outputs putting the device into a low power sleep mode. TCLK I E4 Transmit Clock. LVTTL level input. Input for 20MHz - 80MHz system clock. SYNC I A4, B3 DVCC I C3, C4, E5 Digital Circuit power supply. DGND I A1, C2, F5, E6, G4 Digital Circuit ground. AVCC I A5, A6, B4, B7, G5 Analog power supply (PLL and Analog Circuits). AGND I B5, B6, C6, E7, F7 Analog ground (PLL and Analog Circuits). TDI I F1 Test Data Input to support IEEE 1149.1. There is an internal pullup resistor that defaults this input to high per IEEE 1149.1. TDO O G1 Test Data Output to support IEEE 1149.1 TMS I E3 Test Mode Select Input to support IEEE 1149.1. There is an internal pullup resistor that defaults this input to high per IEEE 1149.1. Assertion of SYNC (high) for at least 1024 synchronization symbols to be transmitted on the Bus LVDS serial output. Synchronization symbols continue to be sent if SYNC continues to be asserted. TTL level input. The two SYNC pins are ORed. TCK I F3 Test Clock Input to support IEEE 1149.1 TRST I G2 Test Reset Input to support IEEE 1149.1. There is an internal pullup resistor that defaults this input to high per IEEE 1149.1. N/A A2, A7, B2, C5, D4, F6, G6, G7 N/C Leave open circuit, do not connect 19 www.national.com SCAN921025H and SCAN921226H Serializer Pin Descriptions SCAN921025H and SCAN921226H Deserializer Pin Descriptions Pin Name I/O Ball Id. Description Data Output. 9 mA CMOS level outputs. ROUT O A5, B4, B6, C4, C7, D6, F5, F7, G4, G5 RCLKR/F I B3 Recovered Clock Rising/Falling strobe select. TTL level input. Selects RCLK active edge for strobing of ROUT data. High selects rising edge. Low selects falling edge. RI+ I D2 + Serial Data Input. Non-inverting Bus LVDS differential input. RI- I C1 - Serial Data Input. Inverting Bus LVDS differential input. PWRDN I D3 Powerdown. TTL level input. PWRDN driven low shuts down the PLL and TRI-STATEs outputs putting the device into a low power sleep mode. LOCK O E1 LOCK goes low when the Deserializer PLL locks onto the embedded clock edge. CMOS level output. Totem pole output structure, does not directly support wired OR connections. RCLK O E2 Recovered Clock. Parallel data rate clock recovered from embedded clock. Used to strobe ROUT, CMOS level output. REN I D1 Output Enable. TTL level input. When driven low, TRI-STATEs ROUT0-ROUT9 and RCLK. DVCC I A7, B7, C5, C6, D5 Digital Circuit power supply. DGND I A1, A6, B5, D7, E4, E7, G3 Digital Circuit ground. AVCC I B1, C2, F1, F2, G1 Analog power supply (PLL and Analog Circuits). AGND I A4, B2, F3, F4, G2 Analog ground (PLL and Analog Circuits). REFCLK I A3 Use this pin to supply a REFCLK signal for the internal PLL frequency. TDI I F6 Test Data Input to support IEEE 1149.1. There is an internal pullup resistor that defaults this input to high per IEEE 1149.1. TDO O G6 Test Data Output to support IEEE 1149.1 TMS I G7 Test Mode Select Input to support IEEE 1149.1. There is an internal pullup resistor that defaults this input to high per IEEE 1149.1. TCK I E5 Test Clock Input to support IEEE 1149.1 TRST I E6 Test Reset Input to support IEEE 1149.1. There is an internal pullup resistor that defaults this input to high per IEEE 1149.1. N/A A2, C3, D4, E3 N/C Leave open circuit, do not connect Deserializer Truth Table INPUTS 1) 2) 3) 4) OUTPUTS PWRDN REN ROUT [0:9] LOCK H (4) H Z H Z H H Active L Active L X Z Z Z H L Z Active Z RCLK LOCK Active indicates the LOCK output will reflect the state of the Deserializer with regard to the selected data stream. RCLK Active indicates the RCLK will be running if the Deserializer is locked. The Timing of RCLK with respect to ROUT is determined by RCLK_R/F. ROUT and RCLK are TRI-STATED when LOCK is asserted High. During Power-up. www.national.com 20 inches (millimeters) unless otherwise noted Order Number SCAN921025HSM or SCAN921226HSM NS Package Number SLC49A National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 SCAN921025H and SCAN921226H High Temperature 20-80 MHz 10 Bit BLVDS SerDes with IEEE 1149.1 (JTAG) and at-speed BIST Physical Dimensions IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated