2SB315B
IGBT-Driver.com Page 1
Data Sheet
2SB315B-5SND0800M170100
SCALE Dual-Channel Plug-and-Play Driver
Driver solution for 130mm x 140mm dual IGBT modules with
fiber-optic i n te rface su ita ble for th e fo llowi ng IGBT modu les:
• 5SND0800M170100
• 5SNE0800M170100
Abstract
The 2SB315B-5SND0800M170100 is a dual-channel driver with a fiber-optic interface
based on CONCEPT’s dual SCALE driver 2SD315AI, a proven technology for reliable
driving a nd safe operation o f IGBTs.
The driver is matched to the above mentioned 1700V modules from ABB. Its plug-and-
play capability makes it ready to operate immediately after mounting. The user needs
invest no effort i n designing or adjusting it to a specific appl ication.
For drive rs adapted to other types of h igh-power and hi gh-voltage IG BT modules, refer
to www.IGBT-Driver.com/go/plug-and-play
Product Highlights Applications
Plug-and-play solution Inverters
Active clamping of Vce at turn-off Motor drive s
IGBT short-circuit and overcurrent protection UPS
No electro lytic capacitors Power-factor correctors
Fiber-optic interface Wind-power converters
Monitoring of power supply voltage Welding
Duty cycle 0... 100% SMPS
Extremely reliable; long service life 2-level converters
Shortens application development t im e and many ot hers
2SB315B
Data Sheet 2SB315B-5SND0800M170100
Page 2 INTELLIGENT POWER ELECTRONICS
Important: Pl ea se ref er t o t he relevant manua l s!
This data sh e e t c ontains on ly produ c t-specif ic data. A de ta iled des c r iption,
must-read application notes and general data applicable to this driver
family are found in: “Description and Application Manual for 2SB315B
SCALE Plu g-and-play IGBT Driver”.
See www.IGBT-Driver.com/go/2SB315B
Dimensions
Dimensions: 130 x 145 mm, 21 mm height (30 mm with connector X1 and flat cable).
Mounting principle: C onnect ed to IGBT mod ule with scr ew s.
Fiber Opt i c s Interfa c es
Interface Remarks Part type #
Drive signal inp ut (Standa r d) Fiber-opt i c receiver (Notes 14,15) HFBR-2522
Drive signal inp ut (Opt. 01) Fiber-optic receiver (Notes 14,17) HFBR-2412Z
Status output (Standard) Fiber-optic transmitter (Note s 14,16) HFBR-1522
Status output (Opt. 01) Fiber-optic transmitter (Notes 14,18) HFBR-1412Z
Absolute Maximum Ratings
Parameter Remarks Min Max Units
Supply voltage VDC VDC to GND (Note 1) 0 16 V
Supply voltage VDD VDD to GND 0 16 V
Gate pea k current Iout Note 6 -15 +15 A
Average supp ly c ur r ent IDC Notes 2,3 500 mA
Output power per gate Note 3 3 W
Switching fr equency Note 3 11 kHz
DC-link volt age Note 4 1200 V
Operating temperature Note 3 -40 +85 °C
Storage temperature -40 +90 °C
All data r efer to +25°C and VDC = 15V unl ess otherwise specified
2SB315B
Data Sheet 2SB315B-5SND0800M170100
IGBT-Driver.com Page 3
Electrical Characteristics
Power supply Remarks Min Typ. Max Units
Nominal supply volta ge VDC To GND (Note 1) 15 Vdc
Supply current IDC Without load 80 mA
Supply current IDC At 11 kHz sw i tching frequency 500 mA
Efficiency η Internal DC/DC converter 85 %
Nominal supply volta ge VDD To GND 15 Vdc
Supply current IDD Wit hout load
Standard 90 mA
Opt. 1 130 mA
Supply current IDD A t 11 kHz switching fr equency
Standard 96 mA
Opt. 1 136 mA
Power supply monitoring Test conditions Min Typ. Max Units
Turn-on threshold Vth Note 5 10.6 Vdc
Hysteresis on/o ff Note 5 0.6 Vdc
Short circuit protection Remarks Min Typ. Max units
Vce-monitoring threshold Bet w. aux. termina ls 3.65 V
Respon se time Note 7 8.8 µs
Blocking time After failure (Note 8) 1 s
Timing characteristics Test conditions Min Typ. Max Units
Turn-on delay tpd(on) Note 9 420 ns
Turn-off delay tpd(off) Note 9 550 ns
Output ri se t i m e tr(out) Gx to Ex (Note 10) 150 ns
Output fall time tf(out) Gx to Ex (Note 10) 80 ns
Dead time between outputs Half-bridge mode 2.5 µs
Gate ou tp uts Te s t conditions Min Typ. Max Units
Turn-on gate resistor Rg(on) 1.2 Ω
Turn-off gate resi stor Rg(off) 5.6 Ω
2SB315B
Data Sheet 2SB315B-5SND0800M170100
Page 4 INTELLIGENT POWER ELECTRONICS
Electrical insulation Test conditions Min Typ. Max Units
Operating voltage Continuous or repeated (Note 4) 1200 Vdc
Test voltage 50 Hz/1 min (Note 11) 4000 VAC(eff)
Partial discharge extinction volt. IEC270 (Note 12) >1700 VAC(pk)
Creep path input-output 20 mm
Creep path output-output 25 mm
Maximum dV/dt at dV=1000 V Note 13 100 kV/μs
All data refer to +25°C and VDC = 15 V u n less otherwise specified
Footnotes to the key data
1) The drivers have a zener diode on each channel for over-voltage protection. When the feed voltage
exceeds 16V, this protection may be exposed to thermal overload.
2) If the specified powe r con s um pti on is e x cee de d, t his i ndi cat es a n over l oa d of t he DC/ DC co nver te r.
It should be noted that these DC/DC converters are not protected against overload.
3) Application-specific self-heating of gate drivers and IGBT modules, especially at high switching
frequency, must be taken into account. As a rule, the switching frequency is limited due to the
switching losses of the IGBT modules. Because CONCEPT cannot predict how the drivers will be
incorpo rated in t he user’s a pplicatio n, no bindi ng recom mended value for sel f-heating a nd thus for
the maximum useable output power can be made. Users are therefore recommended to check the
gate driver’s ambient temperature within the system.
4) This limit is due to active clamping. Refer to the “Description and Application Manual for 2SB315B
SCALE Dual-Channel Plug-and-play IGBT Driver”.
5) Under-voltage monitoring of the supply voltage to the gate driver. If the voltage drops below this
limit, the power modules are switched off.
6) The gate curre nt is limited by the gate resistors located on the driver.
7) Pulse width of the direct output of the gate drive unit (excluding the delay of the gate resistors).
8) The typical blocking time after an error is 1 second. Versions with other bloc king times m ay also be
supplied if required.
9) Measured from the transition of the turn-on or turn-off command at the host controller to direct
output of the gate drive unit (excluding the delay of the gate resistors).
10) Refers to the direct output of the gate drive unit (excluding the delay of the gate resistors).
11) The test voltage of 4000 Vac(rms)/50Hz may be applie d only once during one minute. I t should be
noted that with this (strictly speaking obsolete) test method, some (minor) damage occurs to the
insulation layers due to the partial discharge . Conseque ntly, this test is not performed at CONCEPT
as a series test. In the case of repeated insulation tests (e.g. module test, equipment test, system
test), the subsequent tests should be performed with a lower test voltage: the test voltage is
reduced by 400V for each additional test. The more modern if more elaborate partial-discharge
measurement is preferable to such test methods as it is almost entirely non-destructive.
12) The partial discharge is not measured for the standard types. Tested and selected types with
guaranteed partial-discharge immunity can be supplied for applications with maximum
requirements and higher operating voltages (such as railroad applications).
13) This specification guarantees that the drive information will be transferred reliably even at a high
DC-link voltage and with ultra-fast sw itching operations.
14) The transceivers required at the host controller side are not delivered with the gate driver. It is
recommended to use the same types as used in the gate driver. For product information refer to
www.IGBT-Driver.com/go/fiberoptics
15) The recommended transmitter current at the host controller is 30-35mA, suitable for plastic optic
fibers with a length of less than 2.5 meters. Higher current may increase jitter or delay at turn-off.
16) The transmitter current at the gate driver is about 29mA.
2SB315B
Data Sheet 2SB315B-5SND0800M170100
IGBT-Driver.com Page 5
17) The recommended transmitter current at the host controller is 60mA.
18) The transmitter current at the gate driver is about 53mA.
Important Notice
The data contained in this product data sheet is intended exclusively for technically
trained staff. Handling all high-voltage equipment involves risk to life. Strict compliance
with the respective sa f ety regulations is ma ndatory!
Any handling of electronic devices is subject to the general specifications for protecting
electrostatic-se nsitive devices according to international standard IEC 747-1, Chapte r IX
or European standard EN 100015 (i.e. the workplace, tools, etc. must comply with
these standa rds). O therwise, this product may be damaged.
Legal Disclaimer
This data sheet specifies devices but cannot promise to deliver any specific
characteristics. No warranty or guarantee is given – either expressly or implicitly –
regarding delivery, performance or suitability.
CT-Concept Technologie AG reserves the right to make modifications to its technical
data and product specifications at any time without prior notice. The general terms and
conditi ons of delivery of CT-Concept T ec hnologie AG appl y.
Technical Support
CONCEPT provides expert help for your questions and problems:
Internet: www.IGBT-Driver.com/go/support
Quality
The obligation to high quality is one of the central features laid down in the mission
statement of CT-Concept Technologie AG. The quality management system covers all
stages of product development and production up to delivery. The drivers of the SCALE
series are ma n u f actured to the I SO 9001 stand ard.
2SB315B
Data Sheet 2SB315B-5SND0800M170100
Page 6 INTELLIGENT POWER ELECTRONICS
Ordering In f orma t i o n
The general terms and conditions of delivery o f CT-Concept Technologie AG apply.
Related IGBT CONCEPT Driver Type #
ABB 5SND0800M170100 2SB315B-5SND0800M170100
ABB 5SNE0800M170100 2SB315B-5SND0800M170100
ABB 5SND0800M170100 2SB315B-5SND0800M170100 Opt. 01
ABB 5SNE0800M170100 2SB315B-5S N D 0800M170100 Opt. 01
Opt. 01: ST Fiber-optic interface with threaded port (HFBR-2412Z and HFBR-1412Z), see “Description
and Application Manual for 2SB315B SCALE Dual-Chan nel Plug-and-Play IGBT Drivers”.
Information about Other Products
For drivers adapte d to other high-voltag e or high-power IGBT modules
Direct link: www.IGBT-Driver.com/go/plug-and-play
© Manufacturer
CT-Concept Technologie AG
Intelligent Power Electronic s
Renferst ra sse 15
CH-2504 Biel-Bienne
Switzerland
Tel. +41 - 32 - 344 47 47
Fax +41 - 32 - 344 47 40
E-mail Info@IGBT-Driver.com
Internet www.IGBT-Driver.com
Copyright 2003.. .2010 by CT-Concept Technologie AG - Switzerland. All rights reserved .
We reserve the right to make any technical modifications without prior notice. Version of 2016-05-20
