MPC8343EAVRADDB - Freescale Semiconductor, Inc.

Freescale Semiconductor

Technical Data

The MPC8343EA PowerQUICC ™ II Pro is a next

generation PowerQUICC II integrated host process or. The

MPC8343EA contains a PowerPC™ processor core built on

Power Architecture™ technology with system logic for

networking, storage, and general-purpose embedded

applications. For functional characteristics of the processor,

refer to the MPC8349EA PowerQUICC™ II Pr o Integrated

Host Proces sor Family Refere nce Manual.

T o locate published errata or updates for this document, refer

to the MPC8343EA product summary page on our website

listed on the back cover of this document or, contact your

local Freescale sales office.

Document Number: MPC8343EAEC

Rev. 8, 05/2009

Contents

1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2. Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . 6

3. Power Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 10

4. Clock Input Timing . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5. RESET Initialization . . . . . . . . . . . . . . . . . . . . . . . . . 12

6. DDR and DDR2 SDRAM . . . . . . . . . . . . . . . . . . . . . 14

7. DUART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

8. Ethernet: Three-Speed Ethernet, MII Management . 21

9. USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

10. Local Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

11. JTAG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

12. I2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

13. PCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

14. Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

15. GPIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

16. IPIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

17. SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

18. Package and Pin Listings . . . . . . . . . . . . . . . . . . . . . 48

19. Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

20. Thermal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

21. System Design Information . . . . . . . . . . . . . . . . . . . 72

22. Document Revision History . . . . . . . . . . . . . . . . . . . 75

23. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . 77

MPC8343EA PowerQUICC™ II Pro

Integrated Host Processor Hardware

Specifications

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

2Freescale Semiconductor

Overview

NOTE

The information in this document is acc urate for revision 3.x silicon and

later (in other words, for orderable part numbers ending in A or B). For

informa tion on revis ion 1.1 silic on and earlier versions, s ee the MPC8343E

PowerQUICC™ II Pro Integrated Host Processor Har dw are

Specifications.

See Section 23.1, “Part Numbers Fully Addressed by This Document,” for

silicon revision level determination.

1Overview

This section provides a high-level overview of the MPC8343EA features. Figure 1 shows the major

functional units within the MPC8343EA.

Figure 1. MPC8343EA Block Diagram

Major features of the MPC8343EA are as follows:

• Embedded PowerPC e300 processor core; operates at up to 400 MHz

— High-performance, superscalar processor core

— Floating-point, integer, load/store, system register, and br anch pr ocessing units

— 32-Kbyte instruction cache, 32-Kbyte data cache

— Lockable portion of L1 cache

— Dynamic power management

— S oftware-compatible with the other Freescale processor families that implement Power

Architecture technology

• Double data rate, DDR1/DDR2 SDRAM memory controller

— Programmable timing supporting DDR1 and DDR2 SDRAM

— 32- bit data interface, up to 266 MHz data rate

DUART

Dual I2C

Timers

GPIO

Security Interrupt

Controller

Dual

Role

High-Speed

Local Bus

DDR

SDRAM

Controller

32KB

D-Cache

e300 Core

32KB

I-Cache

USB 2.0 10/100/1000 SEQ

PCI DMA

Ethernet

10/100/1000

Ethernet

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 3

Overview

— Up to four physical banks (chip selects), each bank up to 1 Gbyte indepe ndently addressable

— DRAM chip configurations from 64 Mbits to 1 Gbit with x8/x16 data ports

— Full error checking and correction (ECC) support

— Support for up to 16 simultaneous open pa ges (up to 32 pages for DDR2)

— Contiguous or discontiguous memory mapping

— Read-modify-write support

— Sleep-mode support for SDRAM self refresh

— Auto refresh

— On-the-fly power management using CKE

— Registered DIMM support

— 2.5-V SSTL2 compatib le I/O for DD R1, 1 .8-V SSTL2 compatib le I/O for DDR 2

• Dual three-speed (10/100/1000) Ethernet controllers (TSECs)

— Dual controllers designed to comply with I EEE 802.3®, 802.3u®, 820. 3x®, 802.3z®,

802.3ac® standards

— Ethernet physical interfaces :

– 1000 Mbps IEEE St d. 802.3 RGMII, IEEE Std. 802.3z RTBI, full-duplex

– 10/100 Mbps IEEE Std. 802.3 MII full- and half-duplex

— Buffer descriptors are backward-compatible with MPC8260 and MPC860T 10/100

programming models

— 9.6-Kbyte jumbo frame support

— RMON statistics support

— Internal 2-Kbyte transmit and 2-Kbyt e receive FIFOs per TSEC module

— MII management interface for control and status

— Programmable CRC generation and checking

• PCI in te rfa c e

— Designed to comply with PCI Specification Revision 2.3

— Data bus width:

– 32-bit data PCI interface operating at up to 66 MHz

— PCI 3.3-V compatible

— PCI host bridge capabilities

— PCI age nt mode on PCI interfa ce

— PCI- to-me mor y and memory-to -PC I streaming

— Memory prefetching of PCI read accesses and support for delayed read transactions

— Posting of processor -t o-PCI and PCI-to-memory writes

— On-chip arbitration supporting five masters on PCI

— Acces ses to all PCI addre ss spaces

— Parity supported

— Selectable hardware -enforced coher ency

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

4Freescale Semiconductor

Overview

— Address translation units for address mapping between host and peripheral

— Dual address cycle for target

— Internal configuration registers accessible from PCI

• Security engine is optimized to handle all the algorithms associ ated with IPS ec, SSL/TLS , SRTP,

IEEE Std. 802.11i®, iSCSI, and IKE processing. The security engine contains four

crypto-channels, a controller, and a set of crypto execution units (EUs):

— Public key execution unit (PKEU) :

– RSA and Diff ie-Hellman algorithms

– Programmable field size up to 2048 bits

– Elliptic curve cryptography

– F2m and F(p) modes

– Programmable field size up to 511 bits

— Data encryption standard (DES) execution unit (DEU)

– DES and 3DES algorithms

– Two key (K1, K2) or three key (K1, K2, K3) for 3DES

– ECB and CBC modes for both DES and 3DES

— Advanced encryption standard unit (AESU)

– Implements the Rijndael symmetric-key cipher

– Key lengths of 128, 192, and 256 bits

– ECB, CBC, CCM, and counter (CTR) modes

— XOR parity generation acceler ator for RAID a pplications

— ARC four execution unit (A FEU)

– Stre am ciph er compatible with the RC4 algorithm

– 40- to 128-bit programmable key

— Message digest execution unit (MDEU)

– SHA with 160-, 224-, or 256-bit message digest

– MD5 with 128-bit message digest

– HMAC with either algorithm

— Random number generator (RNG)

— Four crypto-channels, each supporting multi-command descriptor chains

– Static and/or dynamic assignment of crypto-execution units through an integrated controller

– Buff er size of 256 bytes for each execution unit, with flow control for large data sizes

• Universal serial bus (USB) dual role controller

— USB on-the-go mode with both device and host fun ctionali ty

— Complies with USB specification Rev. 2.0

— Can operate as a stand-alone USB device

– One upstream facing port

– Six programmable USB endpoints

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 5

Overview

— Can operate as a stand-alone USB host controller

– USB root hub with one downstream-facing port

– Enhanced host controller interfa ce (EHCI ) compatibl e

– High-speed (480 Mbps), full-speed (12 Mbps), and low-speed (1.5 Mbps) operations

— External PHY with UTMI, serial and UTMI+ low-pin interface (ULPI)

• Local bus controller (LBC)

— Multiplexed 32-bit address and data operating at up to 133 MHz

— Eight chip selects for eight external sl aves

— Up to eight-beat burst transfers

— 32-, 16-, and 8-bit port sizes controlled by an on-chip memory controller

— Three protocol engines on a per chip select basis:

– General-purpose chip select machine (GPCM)

– Three user-programm able m achines ( U PMs)

– Dedicated singl e data rate SDRAM controller

— Parity support

— Default boot ROM chip select with configurable bus width (8-, 16-, or 32-bit)

• Programmable interrupt controller (PIC)

— Functional and programming compatibility with the MPC8260 interrupt controller

— Support for 8 external and 35 internal discrete interrupt sources

— Support for 1 external (optional) and 7 internal machine checkstop interrupt sources

— Programmable highest priority request

— Four groups of interrupts with programmable priority

— External and internal interrupts directed to host processor

— Redirects interr upts to extern al INTA pin in core disable mode.

— Unique vector number for each interrupt source

• Dual industry-standard I2C interface s

— Two-wire interface

— Multiple master support

— Master or slave I2C mode support

— On-chip digital filter ing rejects spikes on the bus

— System initi alization data opti onally loaded from I 2C-1 EPROM by boot sequencer embedded

hardware

• DMA controlle r

— Four independent virtual channels

— Concurrent e xecuti on across multiple channels with programmable bandwidth control

— Handshaking (external control) signals for all channels: DMA_DREQ[0:3],

DMA_DACK[0:3], DMA_DDONE[0:3]

— All channels accessible to local core and remote PCI masters

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

6Freescale Semiconductor

Electrical Characteristics

— Misaligned transfer capabili ty

— Data chaining and direct mode

— Interrupt on completed segment and chain

• DUART

— Two 4-wire interfaces (RxD, TxD, RTS, CTS)

— Programming model compatible with the original 16450 UART and the PC16550D

• Serial peripheral interface (SPI) for master or slave

• General- purpose parallel I/O (GPIO)

— 39 parallel I/O pins multiplexed on various chip interfaces

• System time rs

— P eriodic interrupt timer

— Real-time clock

— Software watchdog timer

— Eight general-purpose timers

• Designed to comply with IEEE Std. 1149.1™, JTAG boundar y scan

• Integrated PCI bus and SDRAM clock generation

2 Electrical Characteristics

This section provides th e AC and DC electrical speci f icat ions and the rmal char acter i stics f or the

MPC8343EA. The MPC8343EA is currently targeted to these specifications. Some of these specifications

are independent of the I/O cell, but are included for a more complete reference . These are not purely I/O

buffer design specifications.

2.1 Overall DC Electrical Characteristics

This section covers the ratings, conditions, and other characteristics.

2.1.1 Absolute Maximum Ratings

Table 1 provides the absolute maximum ratings .

Table 1. Absolute Maximum Ratings1

Characteristic Symbol Max Value Unit Notes

Core supply voltage VDD –0.3 to 1.32 V —

PLL supply voltage AVDD –0.3 to 1.32 V —

DDR and DDR2 DRAM I/O voltage GVDD –0.3 to 2.75

–0.3 to 1.98

V—

Three-speed Ethernet I/O, MII management voltage LVDD –0.3 to 3.63 V —

PCI, local bus, DUART, system control and power management, I2C,

and JTAG I/O voltage

OVDD –0.3 to 3.63 V —

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 7

Electrical Characteristics

2.1.2 Power Supply Voltage Specification

Table 2 provides the recommended operating conditions for the MPC8343EA. Note that the values in

Table 2 are the recommended and test ed operating conditions. Proper device operation outside these

conditions is not guaranteed.

Input voltage DDR DRAM signals MVIN –0.3 to (GVDD + 0.3) V 2, 5

DDR DRAM reference MVREF –0.3 to (GVDD + 0.3) V 2, 5

Three-speed Ethernet signals LVIN –0.3 to (LVDD + 0.3) V 4, 5

Local bus, DUART, CLKIN, system control and

power management, I2C, and JTAG signals

OVIN –0.3 to (OVDD + 0.3) V 3, 5

PCI OVIN –0.3 to (OVDD + 0.3) V 6

Storage temperature range TSTG –55 to 150 °C—

Notes:

1Functional and tested operating conditions are given in Ta b l e 2 . Absolute maximum ratings are stress ratings only, and

functional operation at the maximums is not guaranteed. Stresses beyond those listed may affect device reliability or cause

permanent damage to the device.

2Caution: MVIN must not exceed GVDD by more than 0.3 V. This limit can be exceeded for a maximum of 20 ms during

power-on reset and power-down sequences.

3Caution: OVIN must not exceed OVDD by more than 0.3 V. This limit can be exceeded for a maximum of 20 ms during

power-on reset and power-down sequences.

4Caution: LV IN must not exceed LVDD by more than 0.3 V. This limit can be exceeded for a maximum of 20 ms during power-on

reset and power-down sequences.

5(M,L,O)VIN and MVREF may overshoot/undershoot to a voltage and for a maximum duration as shown in Figure 2.

6OVIN on the PCI interface can overshoot/undershoot according to the PCI Electrical Specification for 3.3-V operation, as

shown in Figure 3.

Table 2. Recommended Operating Conditions

Characteristic Symbol Recommended

Value Unit Notes

Core supply voltage VDD 1.2 V ± 60 mV V 1

PLL supply voltage AVDD 1.2 V ± 60 mV V 1

DDR and DDR2 DRAM I/O voltage GVDD 2.5 V ± 125 mV

1.8 V ± 90 mV

V—

Three-speed Ethernet I/O supply voltage LVDD1 3.3 V ± 330 mV

2.5 V ± 125 mV

V—

Three-speed Ethernet I/O supply voltage LVDD2 3.3 V ± 330 mV

2.5 V ± 125 mV

V—

Table 1. Absolute Maximum Ratings1 (continued)

Characteristic Symbol Max Value Unit Notes

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

8Freescale Semiconductor

Electrical Characteristics

Figure 2 shows the undershoot and overshoot voltages at the interfaces of the MPC8343EA.

Figure 2. Overshoot/Undershoot Voltage for GVDD/OVDD/LVDD

PCI, local bus, DUART, system control and power

management, I2C, and JTAG I/O voltage

OVDD 3.3 V ± 330 mV V —

Note:

1GVDD, LVDD, OVDD

, AVDD, and VDD must track each other and must vary in the same direction—either in the positive or

negative direction.

Table 2. Recommended Operating Conditions (continued)

Characteristic Symbol Recommended

Value Unit Notes

GND

GND – 0.3 V

GND – 0.7 V Not to Exceed 10%

G/L/OVDD + 20%

G/L/OVDD

G/L/OVDD + 5%

of tinterface1

1. tinterface refers to the clock period associated with the bus clock interface.

VIH

VIL

Note:

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 9

Electrical Characteristics

Figure 3 s hows the undershoot and overshoot voltage of the P CI interface of the MPC8343EA for the

3.3-V signals, respectively.

Figure 3. Maximum AC Waveforms on PCI Interface for 3.3-V Signaling

2.1.3 Output Driver Characteristics

Table 3 provides information on the characteristics of the output driver strengths. The values are

prelimina ry estimates .

2.2 Power Sequencing

MPC8343EA does not require the core supply voltage and I/O supply voltages to be applied in any

particular order. Note that during the power ramp up, before the power supplies are stable, there may be a

period of time that I /O pins are actively driven. After the power is stable, as long as POR ESET is asserted,

most I/O pins are three-stated. To minimize the time that I/O pins are actively driven, it is recommended

to apply core voltage before I/O voltage and assert PORESET before the power supplies fully ramp up.

Table 3. Output Drive Capability

Driver Type Output Impedance

(Ω)

Supply

Voltage

Local bus interface utilities signals 40 OVDD = 3.3 V

PCI signals (not including PCI output clocks) 25

PCI output clocks (including PCI_SYNC_OUT) 40

DDR signal 18 GVDD = 2.5 V

DDR2 signal 18

36 (half strength mode)

GVDD = 1.8 V

TSEC/10/100 signals 40 LVDD = 2.5/3.3 V

DUART, system control, I2C, JTAG, USB 40 OVDD = 3.3 V

GPIO signals 40 OVDD = 3.3 V,

LVDD = 2.5/3.3 V

Undervoltage

Waveform

Overvoltage

Waveform

11 ns

(Min)

+7.1 V

7.1 V p-to-p

(Min)

4 ns

(Max)

–3.5 V

7.1 V p-to-p

(Min)

62.5 ns

+3.6 V

0 V

4 ns

(Max)

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

10 Freescale Semiconductor

Power Characteristics

3 Power Characteristics

The estimated typical power dissipation for the MPC8343EA device is shown in Table 4.

Table 5 shows the estimated typical I/O power dissipation for MPC8343EA.

Table 4. MPC8343EA Power Dissipation1

1The values do not include I/O supply power (OVDD, LVDD, GVDD) or AVDD. For I/O power values, see Ta b l e 5 .

Core

Frequency

(MHz)

CSB

Frequency

(MHz)

Typical at TJ= 65 Typical2,3

2Typical power is based on a voltage of VDD = 1.2 V, a junction temperature of TJ = 105°C, and a Dhrystone benchmark

application.

3Thermal solutions may need to design to a value higher than typical power based on the end application, TA target, and I/O

power.

Maximum4

4Maximum power is based on a voltage of VDD = 1.2 V, worst case process, a junction temperature of TJ = 105°C, and an

artificial smoke test.

Unit

PBGA 266 266 1.3 1.6 1.8 W

133 1.1 1.4 1.6 W

400 266 1.5 1.9 2.1 W

133 1.4 1.7 1.9 W

400 200 1.5 1.8 2.0 W

100 1.3 1.7 1.9 W

Table 5. MPC8343EA Typical I/O Power Dissipation

Interface Parameter

DDR2

GVDD

(1.8 V)

DDR1

GVDD

(2.5 V)

OVDD

(3.3 V)

LVDD

(3.3 V)

LVDD

(2.5 V) Unit Comments

DDR I/O

65% utilization

2.5 V

Rs = 20 Ω

Rt = 50 Ω

2 pair of clocks

200 MHz, 32 bits 0.31 0.42 — — — W —

266 MHz, 32 bits 0.35 0.5 — — — W —

PCI I/O

load = 30 pF

33 MHz, 32 bits — — 0.04 — — W —

66 MHz, 32 bits — — 0.07 — — W —

Local bus I/O

load = 25 pF

167 MHz, 32 bits — — 0.34 — — W —

133 MHz, 32 bits — — 0.27 — — W —

83 MHz, 32 bits — — 0.17 — — W —

66 MHz, 32 bits — — 0.14 — — W —

50 MHz, 32 bits — — 0.11 — — W —

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 11

Clock Input Timing

4 Clock Input Timing

This section provides the clock input DC and AC electrical characteristics for the MPC8343EA.

4.1 DC Electrical Characteristics

Table 6 provides the clock input (CLKIN/PCI_SYNC_IN) DC timing specifications for the MPC8343EA.

4.2 AC Electrical Characteristics

The pr imary clock source for t he MPC8343EA can be one of two inputs, CLKIN or PCI_CLK, depending

on whether the device is configured in PCI host or P CI agent mode. Table 7 provides the clock input

(CLKIN/PCI_CLK) AC timing specifications for the MPC8343EA.

TSEC I/O

load = 25 pF

MII — — 0.01 — W Multiply by number

of interfaces used.

GMII or TBI — — 0.06 — W

RGMII or RTBI — — — 0.04 W

USB 12 MHz — — 0.01 — — W —

480 MHz — — 0.2 — — W —

Other I/O — — 0.01 — — W —

Table 6. CLKIN DC Timing Specifications

Parameter Condition Symbol Min Max Unit

Input high voltage — VIH 2.7 OVDD +0.3 V

Input low voltage — VIL –0.3 0.4 V

CLKIN input current 0 V ≤VIN ≤OVDD IIN — ±10 μA

PCI_SYNC_IN input current 0 V ≤VIN ≤0.5 V or

OVDD –0.5V≤VIN ≤OVDD

IIN — ±10 μA

PCI_SYNC_IN input current 0.5 V ≤VIN ≤ OVDD – 0.5 V IIN — ±50 μA

Table 7. CLKIN AC Timing Specifications

Parameter/Condition Symbol Min Typical Max Unit Notes

CLKIN/PCI_CLK frequency fCLKIN ——66MHz1, 6

CLKIN/PCI_CLK cycle time tCLKIN 15 — — ns —

CLKIN/PCI_CLK rise and fall time tKH, tKL 0.6 1.0 2.3 ns 2

Table 5. MPC8343EA Typical I/O Power Dissipation (continued)

Interface Parameter

DDR2

GVDD

(1.8 V)

DDR1

GVDD

(2.5 V)

OVDD

(3.3 V)

LVDD

(3.3 V)

LVDD

(2.5 V) Unit Comments

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

12 Freescale Semiconductor

RESET Initialization

5 RESET Initialization

This section describes the DC and AC electrical s pecifications for the reset initialization timing and

electrical requirements of the MPC8343EA.

5.1 RESET DC Electrical Characteristics

Table 8 provides the DC electrical characteristics for the RESET pins of the MPC8343EA.

CLKIN/PCI_CLK duty cycle tKHK/tCLKIN 40 — 60 % 3

CLKIN/PCI_CLK jitter — — — ±150 ps 4, 5

Notes:

1. Caution: The system, core, USB, security, and TSEC must not exceed their respective maximum or minimum operating

frequencies.

2. Rise and fall times for CLKIN/PCI_CLK are measured at 0.4 and 2.7 V.

3. Timing is guaranteed by design and characterization.

4. This represents the total input jitter—short term and long term—and is guaranteed by design.

5. The CLKIN/PCI_CLK driver’s closed loop jitter bandwidth should be < 500 kHz at –20 dB. The bandwidth must be set low to

allow cascade-connected PLL-based devices to track CLKIN drivers with the specified jitter.

6. Spread spectrum clocking is allowed with 1% input frequency down-spread at maximum 50 KHz modulation rate regardless

of input frequency.

Table 8. RESET Pins DC Electrical Characteristics1

Characteristic Symbol Condition Min Max Unit

Input high voltage VIH —2.0OV

DD +0.3 V

Input low voltage VIL — –0.3 0.8 V

Input current IIN ——±5μA

Output high voltage2VOH IOH = –8.0 mA 2.4 — V

Output low voltage VOL IOL = 8.0 mA — 0.5 V

Output low voltage VOL IOL = 3.2 mA — 0.4 V

Notes:

1. This table applies for pins PORESET

, HRESET, SRESET, and QUIESCE.

2. HRESET and SRESET are open drain pins, thus VOH is not relevant for those pins.

Table 7. CLKIN AC Timing Specifications (continued)

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 13

RESET Initialization

5.2 RESET AC Electrical Characteristics

Table 7 provides the reset initialization AC timing specifications of the MPC8343EA.

Table 9. RESET Initialization Timing Specifications

Parameter/Condition Min Max Unit Notes

Required assertion time of HRESET or SRESET (input) to

activate reset flow

32 — tPCI_SYNC_IN 1

Required assertion time of PORESET with stable clock applied

to CLKIN when the MPC8343EA is in PCI host mode

32 — tCLKIN 2

Required assertion time of PORESET with stable clock applied

to PCI_SYNC_IN when the MPC8343EA is in PCI agent mode

32 — tPCI_SYNC_IN 1

HRESET/SRESET assertion (output) 512 — tPCI_SYNC_IN 1

HRESET negation to SRESET negation (output) 16 — tPCI_SYNC_IN 1

Input setup time for POR configuration signals

(CFG_RESET_SOURCE[0:2] and CFG_CLKIN_DIV) with

respect to negation of PORESET when the MPC8343EA is in

PCI host mode

4—t

CLKIN 2

Input setup time for POR configuration signals

(CFG_RESET_SOURCE[0:2] and CFG_CLKIN_DIV) with

respect to negation of PORESET when the MPC8343EA is in

PCI agent mode

4—t

PCI_SYNC_IN 1

Input hold time for POR configuration signals with respect to

negation of HRESET

0— ns—

Time for the MPC8343EA to turn off POR configuration signals

with respect to the assertion of HRESET

—4 ns3

Time for the MPC8343EA to turn on POR configuration signals

with respect to the negation of HRESET

1—t

PCI_SYNC_IN 1, 3

Notes:

1. tPCI_SYNC_IN is the clock period of the input clock applied to PCI_SYNC_IN. In PCI host mode, the primary clock is applied

to the CLKIN input, and PCI_SYNC_IN period depends on the value of CFG_CLKIN_DIV. See the

MPC8349EA

PowerQUICC™ II Pro Integrated Host Processor Family Reference Manual

2. tCLKIN is the clock period of the input clock applied to CLKIN. It is valid only in PCI host mode. See the

MPC8349EA

PowerQUICC™ II Pro Integrated Host Processor Family Reference Manual

3. POR configuration signals consist of CFG_RESET_SOURCE[0:2] and CFG_CLKIN_DIV.

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

14 Freescale Semiconductor

DDR and DDR2 SDRAM

Table 10 lists the PL L and DLL lock times.

6 DDR and DDR2 SDRAM

This section describes the DC and AC electrical specifications for the DDR SDRAM interface of the

MPC8343EA. Note that DDR SDRAM is GVDD(typ) = 2.5 V and DDR2 SDR AM is GVDD(typ) = 1.8 V.

The AC electr ical specif i cat ions ar e the same for DDR and DRR2 SDRAM.

NOTE

The information in this document is acc urate for revision 3.0 silicon and

later. For information on revision 1.1 silicon and earlier versions see the

MPC8343E PowerQUICC™ II Pro Integrated Host Processor Hardware

Specifications. See Section 23. 1, “Part Numbers Fully Addressed by This

Document,” for silicon revision level determina tion.

6.1 DDR and DDR2 SDRAM DC Electrical Characteristics

Table 11 provides the recommended operating conditions for the DDR2 SDRAM com ponent(s) of the

MPC8343EA when GVDD(typ) = 1.8 V.

Table 10. PLL and DLL Lock Times

Parameter/Condition Min Max Unit Notes

PLL lock times — 100 μs—

DLL lock times 7680 122,880 csb_clk cycles 1, 2

Notes:

1. DLL lock times are a function of the ratio between the output clock and the coherency system bus clock (csb_clk). A 2:1 ratio

results in the minimum and an 8:1 ratio results in the maximum.

2. The csb_clk is determined by the CLKIN and system PLL ratio. See Section 19, “Clocking.”

Table 11. DDR2 SDRAM DC Electrical Characteristics for GVDD(typ) = 1.8 V

Parameter/Condition Symbol Min Max Unit Notes

I/O supply voltage GVDD 1.71 1.89 V 1

I/O reference voltage MVREF 0.49 ×GVDD 0.51 ×GVDD V2

I/O termination voltage VTT MVREF –0.04 MV

REF +0.04 V 3

Input high voltage VIH MVREF +0.125 GV

DD +0.3 V

Input low voltage VIL –0.3 MVREF –0.125 V

Output leakage current IOZ –9.9 9.9 μA4

Output high current (VOUT = 1.420 V) IOH –13.4 — mA

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 15

DDR and DDR2 SDRAM

Table 12 provides the DDR2 capacitance when GVDD(typ) = 1.8 V.

Table 13 provides the recommended operating conditions for t he DDR SDRAM component(s) when

GVDD(typ) = 2.5 V.

Output low current (VOUT = 0.280 V) IOL 13.4 — mA

Notes:

1. GVDD is expected to be within 50 mV of the DRAM GVDD at all times.

2. MVREF is expected to equal 0.5 × GVDD, and to track GVDD DC variations as measured at the receiver. Peak-to-peak noise

on MVREF cannot exceed ±2% of the DC value.

3. VTT is not applied directly to the device. It is the supply to which far end signal termination is made and is expected to equal

MVREF

. This rail should track variations in the DC level of MVREF.

4. Output leakage is measured with all outputs disabled, 0 V ≤ VOUT ≤ GVDD

Table 12. DDR2 SDRAM Capacitance for GVDD(typ) = 1.8 V

Parameter/Condition Symbol Min Max Unit Notes

Input/output capacitance: DQ, DQS, DQS CIO 68pF1

Delta input/output capacitance: DQ, DQS, DQS CDIO —0.5pF1

Note:

1. This parameter is sampled. GVDD = 1.8 V ± 0.090 V, f = 1 MHz, TA = 25°C, VOUT = GVDD/2, VOUT (peak-to-peak) = 0.2 V.

Table 13. DDR SDRAM DC Electrical Characteristics for GVDD(typ) = 2.5 V

Parameter/Condition Symbol Min Max Unit Notes

I/O supply voltage GVDD 2.375 2.625 V 1

I/O reference voltage MVREF 0.49 ×GVDD 0.51 ×GVDD V2

I/O termination voltage VTT MVREF –0.04 MV

REF +0.04 V 3

Input high voltage VIH MVREF +0.18 GV

DD +0.3 V

Input low voltage VIL –0.3 MVREF –0.18 V

Output leakage current IOZ –9.9 –9.9 μA4

Output high current (VOUT = 1.95 V) IOH –15.2 — mA

Output low current (VOUT = 0.35 V) IOL 15.2 — mA

Notes:

1. GVDD is expected to be within 50 mV of the DRAM GVDD at all times.

2. MVREF is expected to be equal to 0.5 × GVDD, and to track GVDD DC variations as measured at the receiver. Peak-to-peak

noise on MVREF may not exceed ±2% of the DC value.

3. VTT is not applied directly to the device. It is the supply to which far end signal termination is made and is expected to be

equal to MVREF

. This rail should track variations in the DC level of MVREF.

4. Output leakage is measured with all outputs disabled, 0 V ≤ VOUT ≤ GVDD

Table 11. DDR2 SDRAM DC Electrical Characteristics for GVDD(typ) = 1.8 V (continued)

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

16 Freescale Semiconductor

DDR and DDR2 SDRAM

Table 14 provides the DDR capacitance when GVDD(typ) = 2.5 V.

Table 15 provides the current draw charact er isti cs f or MVREF.

6.2 DDR and DDR2 SDRAM AC Electrical Characteristics

This section provides the AC electrical characteristics for the DDR and DDR2 SDRAM interface.

6.2.1 DDR and DDR2 SDRAM Input AC Timing Specifications

Table 16 provides the input AC timing specifications for the DDR2 SDRAM when GVDD(typ) = 1.8 V.

Table 17 provides the input AC timing specifications for the DDR SDRAM when GVDD(typ) = 2.5 V.

Table 14. DDR SDRAM Capacitance for GVDD(typ) = 2.5 V

Parameter/Condition Symbol Min Max Unit Notes

Input/output capacitance: DQ, DQS CIO 68pF1

Delta input/output capacitance: DQ, DQS CDIO —0.5pF1

Note:

1. This parameter is sampled. GVDD = 2.5 V ± 0.125 V, f = 1 MHz, TA = 25°C, VOUT = GVDD/2, VOUT (peak-to-peak) = 0.2 V.

Table 15. Current Draw Characteristics for MVREF

Parameter/Condition Symbol Min Max Unit Note

Current draw for MVREF IMVREF — 500 μA1

Note:

1. The voltage regulator for MVREF must supply up to 500 μA current.

Table 16. DDR2 SDRAM Input AC Timing Specifications for 1.8-V Interface

At recommended operating conditions with GVDD of 1.8 ± 5%.

Parameter Symbol Min Max Unit Notes

AC input low voltage VIL —MV

REF – 0.25 V

AC input high voltage VIH MVREF + 0.25 — V

Table 17. DDR SDRAM Input AC Timing Specifications for 2.5-V Interface

At recommended operating conditions with GVDD of 2.5 ± 5%.

Parameter Symbol Min Max Unit Notes

AC input low voltage VIL —MV

REF – 0.31 V

AC input high voltage VIH MVREF + 0.31 — V

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 17

DDR and DDR2 SDRAM

Table 18 provides the input AC timing specifications for the DDR SDRAM interface.

Figure 4 illustrates the DDR input timing diagram showing the tDISKEW timing parameter.

Figure 4. DDR Input Timing Diagram

Table 18. DDR and DDR2 SDRAM Input AC Timing Specifications

At recommended operating conditions with GVDD of (1.8 or 2.5 V) ± 5%.

Parameter Symbol Min Max Unit Notes

Controller Skew for MDQS—MDQ/MECC/MDM tCISKEW ps 1, 2

400 MHz –600 600 3

333 MHz –750 750

266 MHz –750 750

200 MHz –750 750

Notes:

1. tCISKEW represents the total amount of skew consumed by the controller between MDQS[n] and any corresponding bit that

will be captured with MDQS[n]. This should be subtracted from the total timing budget.

2. The amount of skew that can be tolerated from MDQS to a corrresponding MDQ signal is called tDISKEW. This can be

determined by the equation: tDISKEW = ± (T/4 – abs (tCISKEW)); where T is the clock period and abs (tCISKEW) is the absolute

value of tCISKEW.

3. This specification applies only to the DDR interface.

MCK[n]

MCK[n] tMCK

MDQ[x]

MDQS[n]

tDISKEW

D1D0

tDISKEW

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

18 Freescale Semiconductor

DDR and DDR2 SDRAM

6.2.2 DDR and DDR2 SDRAM Output AC Timing Specifications

Table 19 shows the DDR and DDR2 output AC timing specifications.

Table 19. DDR and DDR2 SDRAM Output AC Timing Specifications

At recommended operating conditions with GVDD of (1.8 or 2.5 V) ± 5%.

Parameter Symbol 1Min Max Unit Notes

MCK[n] cycle time, (MCK[n]/MCK[n] crossing) tMCK 7.5 10 ns 2

ADDR/CMD/MODT output setup with respect to MCK tDDKHAS ns 3

400 MHz 1.95 —

333 MHz 2.40 —

266 MHz 3.15 —

200 MHz 4.20 —

ADDR/CMD/MODT output hold with respect to MCK tDDKHAX ns 3

400 MHz 1.95 —

333 MHz 2.40 —

266 MHz 3.15 —

200 MHz 4.20 —

MCS(n) output setup with respect to MCK tDDKHCS ns 3

400 MHz 1.95 —

333 MHz 2.40 —

266 MHz 3.15 —

200 MHz 4.20 —

MCS(n) output hold with respect to MCK tDDKHCX ns 3

400 MHz 1.95 —

333 MHz 2.40 —

266 MHz 3.15 —

200 MHz 4.20 —

MCK to MDQS Skew tDDKHMH –0.6 0.6 ns 4

MDQ/MECC/MDM output setup with respect to

MDQS

tDDKHDS,

tDDKLDS

ps 5

400 MHz 700 —

333 MHz 775 —

266 MHz 1100 —

200 MHz 1200 —

MDQ/MECC/MDM output hold with respect to MDQS tDDKHDX,

tDDKLDX

ps 5

400 MHz 700 —

333 MHz 900 —

266 MHz 1100 —

200 MHz 1200 —

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 19

DDR and DDR2 SDRAM

Figure 5 s hows the DDR SDRAM output timing for the MCK to MDQS skew measurement (tDDKHMH).

Figure 5. Timing Diagram for tDDKHMH

MDQS preamble start tDDKHMP –0.5 × tMCK – 0.6 –0.5 × tMCK + 0.6 ns 6

MDQS epilogue end tDDKHME –0.6 0.6 ns 6

Notes:

1. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for inputs

and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. Output hold time can be read as DDR timing (DD) from

the rising or falling edge of the reference clock (KH or KL) until the output goes invalid (AX or DX). For example, tDDKHAS

symbolizes DDR timing (DD) for the time tMCK memory clock reference (K) goes from the high (H) state until outputs (A) are

set up (S) or output valid time. Also, tDDKLDX symbolizes DDR timing (DD) for the time tMCK memory clock reference (K) goes

low (L) until data outputs (D) are invalid (X) or data output hold time.

2. All MCK/MCK referenced measurements are made from the crossing of the two signals ±0.1 V.

3. ADDR/CMD includes all DDR SDRAM output signals except MCK/MCK, MCS, and MDQ/MECC/MDM/MDQS. For the

ADDR/CMD setup and hold specifications, it is assumed that the clock control register is set to adjust the memory clocks by

1/2 applied cycle.

4. tDDKHMH follows the symbol conventions described in note 1. For example, tDDKHMH describes the DDR timing (DD) from the

rising edge of the MCK(n) clock (KH) until the MDQS signal is valid (MH). tDDKHMH can be modified through control of the

DQSS override bits in the TIMING_CFG_2 registerand is typically set to the same delay as the clock adjust in the CLK_CNTL

register. The timing parameters listed in the table assume that these two parameters are set to the same adjustment value.

See the

MPC8349EA PowerQUICC™ II Pro Integrated Host Processor Family Reference Manual

for the timing modifications

enabled by use of these bits.

5. Determined by maximum possible skew between a data strobe (MDQS) and any corresponding bit of data (MDQ), ECC

(MECC), or data mask (MDM). The data strobe should be centered inside the data eye at the pins of the microprocessor.

6. All outputs are referenced to the rising edge of MCK(n) at the pins of the microprocessor. Note that tDDKHMP follows the

symbol conventions described in note 1.

Table 19. DDR and DDR2 SDRAM Output AC Timing Specifications (continued)

At recommended operating conditions with GVDD of (1.8 or 2.5 V) ± 5%.

Parameter Symbol 1Min Max Unit Notes

MDQS

MCK[n]

tMCK

MDQS

tDDKHMH(min) = –0.6 ns

tDDKHMHmax) = 0.6 ns

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

20 Freescale Semiconductor

DUART

Figure 6 shows the DDR SDRAM output timing diagram.

Figure 6. DDR SDRAM Output Timing Diagram

Figure 7 provides the AC test load for the DDR bus.

Figure 7. DDR AC Test Load

7DUART

This section describes the DC and AC electrical specifications for the DUART interface of the

MPC8343EA.

7.1 DUART DC Electrical Characteristics

Table 20 provides the DC electrical characteristics for the DUART interface of the MPC8343EA.

Table 20. DUART DC Electrical Characteristics

Parameter Symbol Min Max Unit

High-level input voltage VIH 2OV

DD + 0.3 V

Low-level input voltage VIL –0.3 0.8 V

Input current (0.8 V ≤ VIN ≤ 2 V) IIN —±5 μA

ADDR/CMD/MODT

tDDKHMH

tDDKLDS

tDDKHDS

MDQ[x]

MDQS[n]

MCK[n]

MCK[n] tMCK

tDDKLDX

tDDKHDX

D1D0

tDDKHAX,tDDKHCX

Write A0 NOOP

tDDKHMP

tDDKHAS,tDDKHCS

tDDKHME

Output Z0 = 50 Ω

RL = 50 Ω

GVDD/2

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 21

Ethernet: Three-Speed Ethernet, MII Management

7.2 DUART AC Electrical Specifications

Table 21 provides the AC timing parameters for the DUAR T interface of the MPC8343EA.

8 Ethernet: Three-Speed Ethernet, MII Management

This section provides the AC and DC electrical characteristics for three- s peeds (10/100/1000 Mbps) and

MII management.

8.1 Three-Speed Ethernet Controller (TSEC)—MII/RGMII/RTBI

Electrical Characteristics

The electrical char acter isti cs spe ci fied here apply to the media independent interface (MII) , reduced

gigabit media independent interface (RGMII), and reduced ten-bit interface (RTBI) signals except

management data input/output (MDIO) and management data clock (MDC ). The MII interfa ce is defined

for 3.3 V, and the RGMII and RTB I interfaces are defined for 2.5 V. The RGMII and RTBI interfaces

follow the Hewlett-Packard Reduced Pin-Count Interface for Gigabit Ethernet Physical Layer Device

Specification, Versi on 1.2a (9/22/2000). The electrical character istics for MDIO and MDC are specified

in Section 8.3, “Ethernet Management Interface Electrical Characteristics.”

High-level output voltage, IOH = –100 μAV

OH OVDD – 0.2 — V

Low-level output voltage, IOL = 100 μAV

OL —0.2V

Table 21. DUART AC Timing Specifications

Parameter Value Unit Notes

Minimum baud rate 256 baud —

Maximum baud rate > 1,000,000 baud 1

Oversample rate 16 — 2

Notes:

1. Actual attainable baud rate will be limited by the latency of interrupt processing.

2. The middle of a start bit is detected as the 8th sampled 0 after the 1-to-0 transition of the start bit. Subsequent bit values are

sampled each 16th sample.

Table 20. DUART DC Electrical Characteristics (continued)

Parameter Symbol Min Max Unit

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

22 Freescale Semiconductor

Ethernet: Three-Speed Ethernet, MII Management

8.1.1 TSEC DC Electrical Characteristics

MII, RGMII, and RTBI drivers and receivers comply with the DC parametric attributes specified in

Table 22 and Table 23. The RGMII and RTBI signals in Table 23 are based on a 2.5-V CMOS interface

voltage as defined by JEDEC EIA/JESD8-5.

Table 22. MII DC Electrical Characteristics

Parameter Symbol Conditions Min Max Unit

Supply voltage 3.3 V LVDD2 — 2.97 3.63 V

Output high voltage VOH IOH = –4.0 mA LVDD = Min 2.40 LVDD +0.3 V

Output low voltage VOL IOL = 4.0 mA LVDD = Min GND 0.50 V

Input high voltage VIH ——2.0LV

DD +0.3 V

Input low voltage VIL — — –0.3 0.90 V

Input high current IIH VIN1 = LVDD —40μA

Input low current IIL VIN1 = GND –600 — μA

Notes:

1. The symbol VIN, in this case, represents the LVIN symbol referenced in Table 1 and Table 2.

2. MII pins not needed for RGMII or RTBI operation are powered by the OVDD supply.

Table 23. RGMII/RTBI (When Operating at 2.5 V) DC Electrical Characteristics

Parameters Symbol Conditions Min Max Unit

Supply voltage 2.5 V LVDD — 2.37 2.63 V

Output high voltage VOH IOH = –1.0 mA LVDD = Min 2.00 LVDD +0.3 V

Output low voltage VOL IOL = 1.0 mA LVDD = Min GND – 0.3 0.40 V

Input high voltage VIH —LV

DD = Min 1.7 LVDD +0.3 V

Input low voltage VIL —LV

DD = Min –0.3 0.70 V

Input high current IIH VIN1 = LVDD —10μA

Input low current IIL VIN1 = GND –15 — μA

Note:

1. The symbol VIN, in this case, represents the LVIN symbol referenced in Table 1 and Table 2.

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 23

Ethernet: Three-Speed Ethernet, MII Management

8.2 MII, RGMII, and RTBI AC Timing Specifications

The AC timing specifications for MII, RGMII, and RTBI are presented in this section.

8.2.1 MII AC Timing Specifications

This section describes the MII transm it and receive AC timing specifications.

8.2.1.1 MII Transmit AC Timing Specifications

Table 24 provide s the MII transmit AC timing specifications.

Figure 8 s hows the MII transmit AC timing diagram.

Figure 8. MII Transmit AC Timing Diagram

Table 24. MII Transmit AC Timing Specifications

At recommended operating conditions with LVDD/OVDD of 3.3 V ± 10%.

Parameter/Condition Symbol1Min Typ Max Unit

TX_CLK clock period 10 Mbps tMTX —400—ns

TX_CLK clock period 100 Mbps tMTX —40—ns

TX_CLK duty cycle tMTXH/tMTX 35 — 65 %

TX_CLK to MII data TXD[3:0], TX_ER, TX_EN delay tMTKHDX 1 5 15 ns

TX_CLK data clock rise VIL(min) to VIH(max) tMTXR 1.0 — 4.0 ns

TX_CLK data clock fall VIH(max) to VIL(min) tMTXF 1.0 — 4.0 ns

Note:

1. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for inputs

and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMTKHDX symbolizes MII transmit timing

(MT) for the time tMTX clock reference (K) going high (H) until data outputs (D) are invalid (X). In general, the clock reference

symbol is based on two to three letters representing the clock of a particular function. For example, the subscript of tMTX

represents the MII(M) transmit (TX) clock. For rise and fall times, the latter convention is used with the appropriate letter:

R (rise) or F (fall).

TX_CLK

TXD[3:0]

tMTKHDX

tMTX

tMTXH

tMTXR

tMTXF

TX_EN

TX_ER

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

24 Freescale Semiconductor

Ethernet: Three-Speed Ethernet, MII Management

8.2.1.2 MII Receive AC Timing Specifications

Table 25 provid es the MII receive AC timing specifications.

Figure 9 provides the AC test load for TSEC.

Figure 9. TSEC AC Test Load

Figure 10 shows the MII rec eiv e AC timing diagram.

Figure 10. MII Receive AC Timing Diagram

Table 25. MII Receive AC Timing Specifications

At recommended operating conditions with LVDD/OVDD of 3.3 V ± 10%.

Parameter/Condition Symbol1Min Typ Max Unit

RX_CLK clock period 10 Mbps tMRX —400— ns

RX_CLK clock period 100 Mbps tMRX —40—ns

RX_CLK duty cycle tMRXH/tMRX 35 — 65 %

RXD[3:0], RX_DV, RX_ER setup time to RX_CLK tMRDVKH 10.0 — — ns

RXD[3:0], RX_DV, RX_ER hold time to RX_CLK tMRDXKH 10.0 — — ns

RX_CLK clock rise VIL(min) to VIH(max) tMRXR 1.0—4.0ns

RX_CLK clock fall time VIH(max) to VIL(min) tMRXF 1.0—4.0ns

Note:

1. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for inputs

and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMRDVKH symbolizes MII receive timing

(MR) with respect to the time data input signals (D) reach the valid state (V) relative to the tMRX clock reference (K) going to

the high (H) state or setup time. Also, tMRDXKL symbolizes MII receive timing (GR) with respect to the time data input signals

(D) went invalid (X) relative to the tMRX clock reference (K) going to the low (L) state or hold time. In general, the clock

reference symbol is based on three letters representing the clock of a particular functionl. For example, the subscript of tMRX

represents the MII (M) receive (RX) clock. For rise and fall times, the latter convention is used with the appropriate letter:

R (rise) or F (fall).

Output Z0 = 50 ΩOVDD/2

RL = 50 Ω

RX_CLK

RXD[3:0]

tMRDXKH

tMRX

tMRXH

tMRXR

tMRXF

RX_DV

RX_ER tMRDVKH

Valid Data

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 25

Ethernet: Three-Speed Ethernet, MII Management

8.2.2 RGMII and RTBI AC Timing Specifications

Table 26 prese nts the RGMII and RTBI AC timing specifications .

Table 26. RGMII and RTBI AC Timing Specifications

At recommended operating conditions with LVDD of 2.5 V ± 5%.

Parameter/Condition Symbol1Min Typ Max Unit

Data to clock output skew (at transmitter) tSKRGT –0.5 — 0.5 ns

Data to clock input skew (at receiver)2tSKRGT 1.0 — 2.8 ns

Clock cycle duration3tRGT 7.2 8.0 8.8 ns

Duty cycle for 1000Base-T4, 5 tRGTH/tRGT 45 50 55 %

Duty cycle for 10BASE-T and 100BASE-TX3, 5 tRGTH/tRGT 40 50 60 %

Rise time (20%–80%) tRGTR — — 0.75 ns

Fall time (20%–80%) tRGTF — — 0.75 ns

GTX_CLK125 reference clock period tG126—8.0—ns

GTX_CLK125 reference clock duty cycle tG125H/tG125 47 — 53 %

Notes:

1. In general, the clock reference symbol for this section is based on the symbols RGT to represent RGMII and RTBI timing. For

example, the subscript of tRGT represents the TBI (T) receive (RX) clock. Also, the notation for rise (R) and fall (F) times

follows the clock symbol. For symbols representing skews, the subscript is SK followed by the clock being skewed (RGT).

2. This implies that PC board design requires clocks to be routed so that an additional trace delay of greater than 1.5 ns is added

to the associated clock signal.

3. For 10 and 100 Mbps, tRGT scales to 400 ns ± 40 ns and 40 ns ± 4 ns, respectively.

4. Duty cycle may be stretched/shrunk during speed changes or while transitioning to a received packet clock domains as long

as the minimum duty cycle is not violated and stretching occurs for no more than three tRGT of the lowest speed transitioned.

5. Duty cycle reference is LVDD/2.

6. This symbol represents the external GTX_CLK125 and does not follow the original symbol naming convention.

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

26 Freescale Semiconductor

Ethernet: Three-Speed Ethernet, MII Management

Figure 11 shows the RBM II and RTBI AC timing and mult iplexing diagrams.

Figure 11. RGMII and RTBI AC Timing and Multiplexing Diagrams

8.3 Ethernet Management Interface Electrical Characteristics

The electrical char acter i stics specified here apply to the MII manageme nt interfac e signal s management

data input/output (MDIO) and manageme nt data clock (MDC) . The electr ical chara cteris t ics for GMII,

RGMII, TBI and RTBI are specifi ed in Section 8. 1, “Three- Sp eed Ethernet Controller

(TSE C)—MI I/RGMI I/RTBI Electrical Chara cter istics .”

8.3.1 MII Management DC Electrical Characteristics

The MDC and MDIO are defined to operate at a supply voltage of 2.5 or 3.3 V. The DC electrical

characteristics for MDIO and MDC are provided in Table 27 and Table 28.

Table 27. MII Management DC Electrical Characteristics Powered at 2.5 V

Parameter Symbol Conditions Min Max Unit

Supply voltage (2.5 V) LVDD — 2.37 2.63 V

Output high voltage VOH IOH = –1.0 mA LVDD = Min 2.00 LVDD +0.3 V

Output low voltage VOL IOL = 1.0 mA LVDD = Min GND – 0.3 0.40 V

Input high voltage VIH —LV

DD = Min 1.7 — V

Input low voltage VIL —LV

DD = Min –0.3 0.70 V

GTX_CLK

tRGT

tRGTH

tSKRGT

TX_CTL

TXD[8:5]

TXD[7:4]

TXD[9]

TXERR

TXD[4]

TXEN

TXD[3:0]

(At Transmitter)

TXD[8:5][3:0]

TXD[7:4][3:0]

TX_CLK

(At PHY)

RX_CTL

RXD[8:5]

RXD[7:4]

RXD[9]

RXERR

RXD[4]

RXDV

RXD[3:0]

RXD[8:5][3:0]

RXD[7:4][3:0]

RX_CLK

(At PHY)

tSKRGT

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 27

Ethernet: Three-Speed Ethernet, MII Management

8.3.2 MII Management AC Electrical Specifications

Table 29 provides the MII management AC timing specifi cations.

Input high current IIH VIN1 = LVDD —10μA

Input low current IIL VIN = LVDD –15 — μA

Note:

1. The symbol VIN, in this case, represents the LVIN symbol referenced in Table 1 and Table 2.

Table 28. MII Management DC Electrical Characteristics Powered at 3.3 V

Parameter Symbol Conditions Min Max Unit

Supply voltage (3.3 V) LVDD —2.973.63V

Output high voltage VOH IOH = –1.0 mA LVDD = Min 2.10 LVDD +0.3 V

Output low voltage VOL IOL = 1.0 mA LVDD = Min GND 0.50 V

Input high voltage VIH —2.00—V

Input low voltage VIL — — 0.80 V

Input high current IIH LVDD = Max VIN1 = 2.1 V — 40 μA

Input low current IIL LVDD = Max VIN = 0.5 V –600 — μA

Note:

1. The symbol VIN, in this case, represents the LVIN symbol referenced in Table 1 and Table 2.

Table 29. MII Management AC Timing Specifications

At recommended operating conditions with LVDD is 3.3 V ± 10% or 2.5 V ± 5%.

Parameter/Condition Symbol1Min Typ Max Unit Notes

MDC frequency fMDC —2.5—MHz2

MDC period tMDC —400—ns—

MDC clock pulse width high tMDCH 32 — — ns —

MDC to MDIO delay tMDKHDX 10 — 170 ns 3

MDIO to MDC setup time tMDDVKH 5——ns—

MDIO to MDC hold time tMDDXKH 0——ns—

MDC rise time tMDCR — — 10 ns —

Table 27. MII Management DC Electrical Characteristics Powered at 2.5 V (continued)

Parameter Symbol Conditions Min Max Unit

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

28 Freescale Semiconductor

Ethernet: Three-Speed Ethernet, MII Management

Figure 12 shows the MII management AC timing diagram.

Figure 12. MII Management Interface Timing Diagram

MDC fall time tMDHF — — 10 ns —

Notes:

1. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for inputs

and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMDKHDX symbolizes management data

timing (MD) for the time tMDC from clock reference (K) high (H) until data outputs (D) are invalid (X) or data hold time. Also,

tMDDVKH symbolizes management data timing (MD) with respect to the time data input signals (D) reach the valid state (V)

relative to the tMDC clock reference (K) going to the high (H) state or setup time. For rise and fall times, the latter convention

is used with the appropriate letter: R (rise) or F (fall).

2. This parameter is dependent on the csb_clk speed (that is, for a csb_clk of 267 MHz, the maximum frequency is 8.3 MHz

and the minimum frequency is 1.2 MHz; for a csb_clk of 375 MHz, the maximum frequency is 11.7 MHz and the minimum

frequency is 1.7 MHz).

3. This parameter is dependent on the csb_clk speed (that is, for a csb_clk of 267 MHz, the delay is 70 ns and for a csb_clk of

333 MHz, the delay is 58 ns).

Table 29. MII Management AC Timing Specifications (continued)

At recommended operating conditions with LVDD is 3.3 V ± 10% or 2.5 V ± 5%.

Parameter/Condition Symbol1Min Typ Max Unit Notes

MDC

tMDDXKH

tMDC

tMDCH

tMDCR

tMDCF

tMDDVKH

tMDKHDX

MDIO

(Input)

(Output)

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 29

USB

9USB

This section provides the AC and DC electrical specifications for the USB interface of the MPC8343EA.

9.1 USB DC Electrical Characteristics

Table 30 provides the DC electrical characteristics for the USB interface.

9.2 USB AC Electrical Specifications

Table 31 describes the general timing parameters of the USB interface of the MPC8343EA.

Table 30. USB DC Electrical Characteristics

Parameter Symbol Min Max Unit

High-level input voltage VIH 2OV

DD +0.3 V

Low-level input voltage VIL –0.3 0.8 V

Input current IIN —±5 μA

High-level output voltage, IOH = –100 μAV

OH OVDD –0.2 — V

Low-level output voltage, IOL = 100 μAV

OL —0.2V

Table 31. USB General Timing Parameters (ULPI Mode Only)

Parameter Symbol1Min Max Unit Notes

USB clock cycle time tUSCK 15 — ns 2–5

Input setup to USB clock—all inputs tUSIVKH 4—ns2–5

Input hold to USB clock—all inputs tUSIXKH 1—ns2–5

USB clock to output valid—all outputs tUSKHOV —7ns2–5

Output hold from USB clock—all outputs tUSKHOX 2—ns2–5

Notes:

1. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for inputs

and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tUSIXKH symbolizes USB timing (US) for

the input (I) to go invalid (X) with respect to the time the USB clock reference (K) goes high (H). Also, tUSKHOX symbolizes

USB timing (US) for the USB clock reference (K) to go high (H), with respect to the output (O) going invalid (X) or output hold

time.

2. All timings are in reference to USB clock.

3. All signals are measured from OVDD/2 of the rising edge of the USB clock to 0.4 ×OVDD of the signal in question for 3.3 V

signaling levels.

4. Input timings are measured at the pin.

5. For active/float timing measurements, the Hi-Z or off-state is defined to be when the total current delivered through the

component pin is less than or equal to that of the leakage current specification.

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

30 Freescale Semiconductor

Local Bus

Figure 13 and Figure 14 provide the AC test load and signals for the USB, respectively.

Figure 13. USB AC Test Load

Figure 14. USB Signals

10 Local Bus

This section descr ibes t he DC and AC electrical specif i cati ons for the local bus interf ace of the

MPC8343EA.

10.1 Local Bus DC Electrical Characteristics

Table 32 provides the DC electrical characteristics for the local bus interface.

Table 32. Local Bus DC Electrical Characteristics

Parameter Symbol Min Max Unit

High-level input voltage VIH 2OV

DD +0.3 V

Low-level input voltage VIL –0.3 0.8 V

Input current IIN —±5μA

High-level output voltage, IOH = –100 μAV

OH OVDD –0.2 — V

Low-level output voltage, IOL = 100 μAV

OL —0.2V

Output Z0 = 50 ΩOVDD/2

RL = 50 Ω

Output Signals:

tUSKHOV

USB0_CLK/USB1_CLK/DR_CLK

Input Signals

tUSIXKH

tUSIVKH

tUSKHOX

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 31

Local Bus

10.2 Local Bus AC Electrical Specification

Table 33 and Table 34 describe the general timing parameters of the l ocal bus interfa ce of the

MPC8343EA.

Table 33. Local Bus General Timing Parameters—DLL On

Parameter Symbol1Min Max Unit Notes

Local bus cycle time tLBK 7.5 — ns 2

Input setup to local bus clock (except LUPWAIT) tLBIVKH1 1.5 — ns 3, 4

LUPWAIT input setup to local bus clock tLBIVKH2 2.2 — ns 3, 4

Input hold from local bus clock (except LUPWAIT) tLBIXKH1 1.0 — ns 3, 4

LUPWAIT Input hold from local bus clock tLBIXKH2 1.0 — ns 3, 4

LALE output fall to LAD output transition (LATCH hold time) tLBOTOT1 1.5 — ns 5

LALE output fall to LAD output transition (LATCH hold time) tLBOTOT2 3—ns6

LALE output fall to LAD output transition (LATCH hold time) tLBOTOT3 2.5 — ns 7

Local bus clock to LALE rise tLBKHLR —4.5ns—

Local bus clock to output valid (except LAD/LDP and LALE) tLBKHOV1 —4.5ns—

Local bus clock to data valid for LAD/LDP tLBKHOV2 —4.5ns3

Local bus clock to address valid for LAD tLBKHOV3 —4.5ns3

Output hold from local bus clock (except LAD/LDP and LALE) tLBKHOX1 1—ns3

Output hold from local bus clock for LAD/LDP tLBKHOX2 1—ns3

Local bus clock to output high impedance for LAD/LDP tLBKHOZ —3.8ns8

Notes:

1. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for inputs

and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tLBIXKH1 symbolizes local bus timing (LB)

for the input (I) to go invalid (X) with respect to the time the tLBK clock reference (K) goes high (H), in this case for clock one

(1). Also, tLBKHOX symbolizes local bus timing (LB) for the tLBK clock reference (K) to go high (H), with respect to the output

(O) going invalid (X) or output hold time.

2. All timings are in reference to the rising edge of LSYNC_IN.

3. All signals are measured from OVDD/2 of the rising edge of LSYNC_IN to 0.4 ×OVDD of the signal in question for 3.3 V

signaling levels.

4. Input timings are measured at the pin.

5. tLBOTOT1 should be used when RCWH[LALE] is not set and when the load on the LALE output pin is at least 10 pF less than

the load on the LAD output pins.

6. tLBOTOT2 should be used when RCWH[LALE] is set and when the load on the LALE output pin is at least 10 pF less than the

load on the LAD output pins.

7. tLBOTOT3 should be used when RCWH[LALE] is set and when the load on the LALE output pin equals the load on the LAD

output pins.

8. For active/float timing measurements, the Hi-Z or off-state is defined to be when the total current delivered through the

component pin is less than or equal to that of the leakage current specification.

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

32 Freescale Semiconductor

Local Bus

Figure 15 provides the AC test load for the local bus.

Figure 15. Local Bus C Test Load

Table 34. Local Bus General Timing Parameters—DLL Bypass9

Parameter Symbol1Min Max Unit Notes

Local bus cycle time tLBK 15 — ns 2

Input setup to local bus clock tLBIVKH 7—ns3, 4

Input hold from local bus clock tLBIXKH 1.0 — ns 3, 4

LALE output fall to LAD output transition (LATCH hold time) tLBOTOT1 1.5 — ns 5

LALE output fall to LAD output transition (LATCH hold time) tLBOTOT2 3—ns6

LALE output fall to LAD output transition (LATCH hold time) tLBOTOT3 2.5 — ns 7

Local bus clock to output valid tLBKLOV —3ns3

Local bus clock to output high impedance for LAD/LDP tLBKHOZ —4ns8

Notes:

1. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for inputs

and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tLBIXKH1 symbolizes local bus timing (LB)

for the input (I) to go invalid (X) with respect to the time the tLBK clock reference (K) goes high (H), in this case for clock one

(1). Also, tLBKHOX symbolizes local bus timing (LB) for the tLBK clock reference (K) to go high (H), with respect to the output

(O) going invalid (X) or output hold time.

2. All timings are in reference to the falling edge of LCLK0 (for all outputs and for LGTA and LUPWAIT inputs) or the rising edge

of LCLK0 (for all other inputs).

3. All signals are measured from OVDD/2 of the rising/falling edge of LCLK0 to 0.4 ×OVDD of the signal in question for 3.3 V

signaling levels.

4. Input timings are measured at the pin.

5. tLBOTOT1 should be used when RCWH[LALE] is not set and when the load on the LALE output pin is at least 10 pF less than

the load on the LAD output pins.

6. tLBOTOT2 should be used when RCWH[LALE] is set and when the load on the LALE output pin is at least 10 pF less than the

load on the LAD output pins.the

7. tLBOTOT3 should be used when RCWH[LALE] is set and when the load on the LALE output pin equals to the load on the LAD

output pins.

8. For purposes of active/float timing measurements, the Hi-Z or off-state is defined to be when the total current delivered

through the component pin is less than or equal to the leakage current specification.

9. DLL bypass mode is not recommended for use at frequencies above 66 MHz.

Output Z0 = 50 ΩOVDD/2

RL = 50 Ω

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 33

Local Bus

Figure 16 through Figure 21 show the local bus signals.

Figure 16. Local Bus Signals, Nonspecial Signals Only (DLL Enabled)

Figure 17. Local Bus Signals, Nonspecial Signals Only (DLL Bypass Mode)

Output Signals:

LA[27:31]/LBCTL/LBCKE/LOE

LSDA10/LSDWE/LSDRAS/

LSDCAS/LSDDQM[0:3]

tLBKHOV

LSYNC_IN

Input Signals:

LAD[0:31]/LDP[0:3]

Output (Data) Signals:

LAD[0:31]/LDP[0:3]

Output (Address) Signal:

LAD[0:31]

LALE

tLBIXKH

tLBIVKH

tLBIXKH

tLBKHOX

tLBKHOZ

tLBKHLR

tLBOTOT

tLBKHOZ

tLBKHOX

Output Signals:

LSDA10/LSDWE/LSDRAS/

LSDCAS/LSDDQM[0:3]

LCLK[n]

Input Signals:

LAD[0:31]/LDP[0:3]

Output Signals:

LAD[0:31]/LDP[0:3]

LALE

Input Signal:

LGTA

tLBIXKH

tLBKLOV

tLBKHOZ

tLBOTOT

tLBIVKH

tLBIXKH

tLBKLOV

tLBIVKH

LA[27:31]/LBCTL/LBCKE/LOE

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

34 Freescale Semiconductor

Local Bus

Figure 18. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 2 (DLL Enabled)

Figure 19. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 2 (DLL Bypass Mode)

LSYNC_IN

UPM Mode Input Signal:

LUPWAIT

tLBIXKH2

tLBIVKH2

tLBIVKH1

tLBIXKH1

tLBKHOZ1

Input Signals:

LAD[0:31]/LDP[0:3]

UPM Mode Output Signals:

LCS[0:7]/LBS[0:3]/LGPL[0:5]

GPCM Mode Output Signals:

LCS[0:7]/LWE

tLBKHOV1

tLBKHOZ1

LCLK

UPM Mode Input Signal:

LUPWAIT

tLBIXKH

tLBIVKH

tLBIXKH

tLBKHOZ

Input Signals:

LAD[0:31]/LDP[0:3]

UPM Mode Output Signals:

LCS[0:7]/LBS[0:3]/LGPL[0:5]

GPCM Mode Output Signals:

LCS[0:7]/LWE

tLBKLOV

tLBKHOZ

(DLL Bypass Mode)

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 35

Local Bus

Figure 20. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 4 (DLL Bypass Mode)

LCLK

UPM Mode Input Signal:

LUPWAIT

tLBIXKH

tLBIVKH

tLBIXKH

tLBKHOZ

UPM Mode Output Signals:

LCS[0:7]/LBS[0:3]/LGPL[0:5]

GPCM Mode Output Signals:

LCS[0:7]/LWE

tLBKLOV

tLBKHOZ

Input Signals:

LAD[0:31]/LDP[0:3]

(DLL Bypass Mode)

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

36 Freescale Semiconductor

JTAG

Figure 21. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 4 (DLL Enabled)

11 JTAG

This section describes the DC and AC electrical specifications for the IEEE Std. 1 149.1 (JTAG) interface

of the MPC8343EA

11.1 JTAG DC Electrical Characteristics

Table 35 provides the DC electrical characteristics for the IEEE Std. 1149.1 (JTAG) interface of the

MPC8343EA.

Table 35. JTAG Interface DC Electrical Characteristics

Characteristic Symbol Condition Min Max Unit

Input high voltage VIH —OV

DD –0.3 OV

DD +0.3 V

Input low voltage VIL — –0.3 0.8 V

Input current IIN ——±5μA

Output high voltage VOH IOH = –8.0 mA 2.4 — V

LSYNC_IN

UPM Mode Input Signal:

LUPWAIT

tLBIXKH2

tLBIVKH2

tLBIVKH1

tLBIXKH1

tLBKHOZ1

Input Signals:

LAD[0:31]/LDP[0:3]

UPM Mode Output Signals:

LCS[0:3]/LBS[0:3]/LGPL[0:5]

GPCM Mode Output Signals:

LCS[0:3]/LWE

tLBKHOV1

tLBKHOZ1

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 37

JTAG

11.2 JTAG AC Timing Specifications

This section describes the AC electrical specifications for the IEEE Std. 1 149. 1 (JTAG) interface of the

MPC8343EA. Table 36 provides the J TAG AC timing specifications as defined in Figure 23 through

Figure 26.

Output low voltage VOL IOL = 8.0 mA — 0.5 V

Output low voltage VOL IOL = 3.2 mA — 0.4 V

Table 36. JTAG AC Timing Specifications (Independent of CLKIN)1

At recommended operating conditions (see Ta bl e 2 ).

Parameter Symbol2Min Max Unit Notes

JTAG external clock frequency of operation fJTG 033.3MHz—

JTAG external clock cycle time t JTG 30 — ns —

JTAG external clock pulse width measured at 1.4 V tJTKHKL 15 — ns —

JTAG external clock rise and fall times tJTGR, tJTGF 02ns—

TRST assert time tTRST 25 — ns 3

Input setup times:

Boundary-scan data

TMS, TDI

tJTDVKH

tJTIVKH

—

Input hold times:

Boundary-scan data

TMS, TDI

tJTDXKH

tJTIXKH

—

Valid times:

Boundary-scan data

TDO

tJTKLDV

tJTKLOV

Output hold times:

Boundary-scan data

TDO

tJTKLDX

tJTKLOX

—

Table 35. JTAG Interface DC Electrical Characteristics (continued)

Characteristic Symbol Condition Min Max Unit

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

38 Freescale Semiconductor

JTAG

Figure 22 provides the AC test load for TDO and the boundary-scan outputs of the MPC8343EA.

Figure 22. AC Test Load for the JTAG Interface

Figure 23 provides the JTAG clock input timing diagram.

Figure 23. JTAG Clock Input Timing Diagram

Figure 24 pr ovides the TRST timing diagram.

Figure 24. TRST Timing Diagram

JTAG external clock to output high impedance:

Boundary-scan data

TDO

tJTKLDZ

tJTKLOZ

5, 6

Notes:

1. All outputs are measured from the midpoint voltage of the falling/rising edge of tTCLK to the midpoint of the signal in question.

The output timings are measured at the pins. All output timings assume a purely resistive 50 Ω load (see Figure 13).

Time-of-flight delays must be added for trace lengths, vias, and connectors in the system.

2. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for inputs

and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tJTDVKH symbolizes JTAG device timing

(JT) with respect to the time data input signals (D) reaching the valid state (V) relative to the tJTG clock reference (K) going

to the high (H) state or setup time. Also, tJTDXKH symbolizes JTAG timing (JT) with respect to the time data input signals (D)

went invalid (X) relative to the tJTG clock reference (K) going to the high (H) state. In general, the clock reference symbol is

based on three letters representing the clock of a particular function. For rise and fall times, the latter convention is used with

the appropriate letter: R (rise) or F (fall).

3. TRST is an asynchronous level sensitive signal. The setup time is for test purposes only.

4. Non-JTAG signal input timing with respect to tTCLK.

5. Non-JTAG signal output timing with respect to tTCLK.

6. Guaranteed by design and characterization.

Table 36. JTAG AC Timing Specifications (Independent of CLKIN)1 (continued)

At recommended operating conditions (see Ta bl e 2 ).

Parameter Symbol2Min Max Unit Notes

Output Z0 = 50 ΩOVDD/2

RL = 50 Ω

JTAG

tJTKHKL tJTGR

External Clock VMVMVM

tJTG tJTGF

VM = Midpoint Voltage (OVDD/2)

TRST

VM = Midpoint Voltage (OVDD/2)

VM VM

tTRST

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 39

JTAG

Figure 25 provides the boundary-scan timing diagram.

Figure 25. Boundary-Scan Timing Diagram

Figure 26 provide s the test access port timing diagram.

Figure 26. Test Access Port Timing Diagram

VM = Midpoint Voltage (OVDD/2)

VM VM

tJTDVKH

tJTDXKH

Boundary

Data Outputs

Boundary

Data Outputs

JTAG

External Clock

Boundary

Data Inputs

Output Data Valid

tJTKLDX

tJTKLDZ

tJTKLDV

Input

Data Valid

Output Data Valid

VM = Midpoint Voltage (OVDD/2)

VM VM

tJTIVKH

tJTIXKH

JTAG

External Clock

Output Data Valid

tJTKLOX

tJTKLOZ

tJTKLOV

Input

Data Valid

Output Data Valid

TDI, TMS

TDO

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

40 Freescale Semiconductor

I2C

12 I2C

This section describes the DC and AC electrical characteristics for the I2C interface of the M PC8343EA.

12.1 I2C DC Electrical Characteristics

Table 37 provides the DC electrical characteristics for the I2C interface of the MPC8343EA.

12.2 I2C AC Electrical Specifications

Table 38 provides the AC timing parameters for the I2C interface of the MPC8343EA. Note that all values

re fer to VIH(min) and VIL(max) le ve ls (see Table 37).

Table 37. I2C DC Electrical Characteristics

At recommended operating conditions with OVDD of 3.3 V ± 10%.

Parameter Symbol Min Max Unit Notes

Input high voltage level VIH 0.7 ×OVDD OVDD +0.3 V

Input low voltage level VIL –0.3 0.3 ×OVDD V

Low level output voltage VOL 00.2×OVDD V1

Output fall time from VIH(min) to VIL(max) with a bus

capacitance from 10 to 400 pF

tI2KLKV 20 + 0.1 ×CB250 ns 2

Pulse width of spikes which must be suppressed by the

input filter

tI2KHKL 050ns3

Input current each I/O pin (input voltage is between

0.1 ×OVDD and 0.9 ×OVDD(max)

II–10 10 μA4

Capacitance for each I/O pin CI—10pF

Notes:

1. Output voltage (open drain or open collector) condition = 3 mA sink current.

2. CB = capacitance of one bus line in pF.

3. Refer to the

MPC8349EA Integrated Host Processor Family Reference Manual,

for information on the digital filter used.

4. I/O pins obstruct the SDA and SCL lines if OVDD is switched off.

Table 38. I2C AC Electrical Specifications

Parameter Symbol1Min Max Unit

SCL clock frequency fI2C 0400kHz

Low period of the SCL clock tI2CL 1.3 — μs

High period of the SCL clock tI2CH 0.6 — μs

Setup time for a repeated START condition tI2SVKH 0.6 — μs

Hold time (repeated) START condition (after this period, the first clock

pulse is generated)

tI2SXKL 0.6 — μs

Data setup time tI2DVKH 100 — ns

Data hold time:CBUS compatible masters

I2C bus devices

tI2DXKL —

—

0.93

μs

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 41

I2C

Figure 13 provides the AC test load for the I2C.

Figure 27. I2C AC Test Load

Figure 28 shows the AC timing diagram for the I2C bus.

Figure 28. I2C Bus AC Timing Diagram

Fall time of both SDA and SCL signals5tI2CF __ 300 ns

Setup time for STOP condition tI2PVKH 0.6 — μs

Bus free time between a STOP and START condition tI2KHDX 1.3 — μs

Noise margin at the LOW level for each connected device (including

hysteresis)

VNL 0.1 ×OVDD —V

Noise margin at the HIGH level for each connected device (including

hysteresis)

VNH 0.2 ×OVDD —V

Notes:

1. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for inputs

and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tI2DVKH symbolizes I2C timing (I2) with

respect to the time data input signals (D) reach the valid state (V) relative to the tI2C clock reference (K) going to the high (H)

state or setup time. Also, tI2SXKL symbolizes I2C timing (I2) for the time that the data with respect to the start condition (S)

goes invalid (X) relative to the tI2C clock reference (K) going to the low (L) state or hold time. Also, tI2PVKH symbolizes I2C

timing (I2) for the time that the data with respect to the stop condition (P) reaches the valid state (V) relative to the tI2C clock

reference (K) going to the high (H) state or setup time. For rise and fall times, the latter convention is used with the appropriate

letter: R (rise) or F (fall).

2. MPC8343EA provides a hold time of at least 300 ns for the SDA signal (referred to the VIH(min) of the SCL signal) to bridge

the undefined region of the falling edge of SCL.

3. The maximum tI2DVKH must be met only if the device does not stretch the LOW period (tI2CL) of the SCL signal.

4. CB = capacitance of one bus line in pF.

5.)The MPC8343EA does not follow the “I2C-BUS Specifications” version 2.1 regarding the tI2CF AC parameter.

Table 38. I2C AC Electrical Specifications (continued)

Parameter Symbol1Min Max Unit

Output Z0 = 50 ΩOVDD/2

RL = 50 Ω

SrS

SDA

SCL

tI2CF

tI2SXKL

tI2CL

tI2CH

tI2DXKL

tI2DVKH

tI2SXKL

tI2SVKH

tI2KHKL

tI2PVKH

tI2CR

tI2CF

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

42 Freescale Semiconductor

PCI

13 PCI

This section describes the DC and AC electrical specifications for the PCI bus of the MPC8343EA.

13.1 PCI DC Electrical Characteristics

Table 39 provides the DC electrical characteristics for the PCI interface of the MPC8343EA.

13.2 PCI AC Electrical Specifications

This section describes the general AC ti ming parameters of the P CI bus of the MPC8343EA. Note that the

PCI_CLK or PCI_SYNC_IN signal is used as the PCI input clock depending on whether the MPC8343EA

is configured as a host or agent device. Table 40 provides the PCI AC timing specificati ons at 66 MHz.

Table 39. PCI DC Electrical Characteristics

Parameter Symbol Test Condition Min Max Unit

High-level input voltage VIH VOUT ≥VOH (min) or 2 OVDD +0.3 V

Low-level input voltage VIL VOUT ≤VOL (max) –0.3 0.8 V

Input current IIN VIN1= 0 V or VIN = OVDD —±5 μA

High-level output voltage VOH OVDD = min,

IOH = –100 μA

OVDD –0.2 — V

Low-level output voltage VOL OVDD = min,

IOL = 100 μA

—0.2V

Note:

1. The symbol VIN, in this case, represents the OVIN symbol referenced in Ta b le 1 .

Table 40. PCI AC Timing Specifications at 66 MHz1

Parameter Symbol2Min Max Unit Notes

Clock to output valid tPCKHOV —6.0ns3

Output hold from clock tPCKHOX 1—ns3

Clock to output high impedance tPCKHOZ —14ns3, 4

Input setup to clock tPCIVKH 3.0 — ns 3, 5

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 43

PCI

Table 41 provid es the PCI AC timing specifications at 33 MHz .

Figure 29 provides the AC test load for PCI.

Figure 29. PCI AC Test Load

Input hold from clock tPCIXKH 0—ns3, 5

Notes:

1. PCI timing depends on M66EN and the ratio between PCI1/PCI2. Refer to the PCI chapter of the reference manual for a

description of M66EN.

2. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for inputs

and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tPCIVKH symbolizes PCI timing (PC) with

respect to the time the input signals (I) reach the valid state (V) relative to the PCI_SYNC_IN clock, tSYS, reference (K) going

to the high (H) state or setup time. Also, tPCRHFV symbolizes PCI timing (PC) with respect to the time hard reset (R) went

high (H) relative to the frame signal (F) going to the valid (V) state.

3. See the timing measurement conditions in the

PCI 2.3 Local Bus Specifications

4. For active/float timing measurements, the Hi-Z or off-state is defined to be when the total current delivered through the

component pin is less than or equal to the leakage current specification.

5. Input timings are measured at the pin.

Table 41. PCI AC Timing Specifications at 33 MHz

Parameter Symbol1Min Max Unit Notes

Clock to output valid tPCKHOV —11ns2

Output hold from clock tPCKHOX 2—ns2

Clock to output high impedance tPCKHOZ —14ns2, 3

Input setup to clock tPCIVKH 3.0 — ns 2, 4

Input hold from clock tPCIXKH 0—ns2, 4

Notes:

1. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for inputs

and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tPCIVKH symbolizes PCI timing (PC) with

respect to the time the input signals (I) reach the valid state (V) relative to the PCI_SYNC_IN clock, tSYS, reference (K) going

to the high (H) state or setup time. Also, tPCRHFV symbolizes PCI timing (PC) with respect to the time hard reset (R) went

high (H) relative to the frame signal (F) going to the valid (V) state.

2. See the timing measurement conditions in the

PCI 2.3 Local Bus Specifications

3. For active/float timing measurements, the Hi-Z or off-state is defined to be when the total current delivered through the

component pin is less than or equal to the leakage current specification.

4. Input timings are measured at the pin.

Table 40. PCI AC Timing Specifications at 66 MHz1 (continued)

Parameter Symbol2Min Max Unit Notes

Output Z0 = 50 ΩOVDD/2

RL = 50 Ω

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

44 Freescale Semiconductor

Timers

Figure 30 s hows the PCI input AC timing diagram.

Figure 30. PCI Input AC Timing Diagram

Figure 31 s hows the PCI output AC timing diagram.

Figure 31. PCI Output AC Timing Diagram

14 Timers

This section describes the DC and AC electrical specific ations for the timers.

14.1 Timer DC Electrical Characteristics

Table 42 provides the DC electrical characteristics for the MPC8343EA timer pins, including TIN, TOUT ,

TGATE, and RTC _CLK.

Table 42. Timer DC Electrical Characteristics

Characteristic Symbol Condition Min Max Unit

Input high voltage VIH —2.0OV

DD +0.3 V

Input low voltage VIL — –0.3 0.8 V

Input current IIN ——±5μA

Output high voltage VOH IOH = –8.0 mA 2.4 — V

Output low voltage VOL IOL = 8.0 mA — 0.5 V

Output low voltage VOL IOL = 3.2 mA — 0.4 V

tPCIVKH

CLK

Input

tPCIXKH

CLK

Output Delay

tPCKHOV

High-Impedance

tPCKHOZ

Output

tPCKHOX

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 45

GPIO

14.2 Timer AC Timing Specifications

Table 43 provides the timer input and output AC timing specifications.

15 GPIO

This section describes the DC and AC electrical specifications for the GPIO.

15.1 GPIO DC Electrical Characteristics

Table 44 provides the DC electrical characteristics for the MPC8343EA GPIO.

15.2 GPIO AC Timing Specifications

Table 45 provides the GPIO input and output AC timing specifications.

Table 43. Timers Input AC Timing Specifications1

Characteristic Symbol2Min Unit

Timers inputs—minimum pulse width tTIWID 20 ns

Notes:

1. Input specifications are measured from the 50 percent level of the signal to the 50 percent level of the rising edge of CLKIN.

Timings are measured at the pin.

2. Timer inputs and outputs are asynchronous to any visible clock. Timer outputs should be synchronized before use by external

synchronous logic. Timer inputs are required to be valid for at least tTIWID ns to ensure proper operation.

Table 44. GPIO DC Electrical Characteristics

Characteristic Symbol Condition Min Max Unit

Input high voltage VIH 2.0 OVDD +0.3 V

Input low voltage VIL –0.3 0.8 V

Input current IIN ±5 μA

Output high voltage VOH IOH = –8.0 mA 2.4 — V

Output low voltage VOL IOL = 8.0 mA — 0.5 V

Output low voltage VOL IOL = 3.2 mA — 0.4 V

Table 45. GPIO Input AC Timing Specifications1

Characteristic Symbol2Min Unit

GPIO inputs—minimum pulse width tPIWID 20 ns

Notes:

1. Input specifications are measured from the 50 percent level of the signal to the 50 percent level of the rising edge of CLKIN.

Timings are measured at the pin.

2. GPIO inputs and outputs are asynchronous to any visible clock. GPIO outputs should be synchronized before use by external

synchronous logic. GPIO inputs must be valid for at least tPIWID ns to ensure proper operation.

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

46 Freescale Semiconductor

IPIC

16 IPIC

This section describes the DC and AC electrical specifications for the external interrupt pins.

16.1 IPIC DC Electrical Characteristics

Table 46 provides the DC electrical characteristics for the external interrupt pins.

16.2 IPIC AC Timing Specifications

Table 47 provides the IPIC input and output AC timing specifications.

17 SPI

This section describes the SPI DC and AC electrical specific ations.

17.1 SPI DC Electrical Characteristics

Table 48 provides the SPI DC electr ical chara ct er ist ics.

Table 46. IPIC DC Electrical Characteristics1

Characteristic Symbol Condition Min Max Unit Notes

Input high voltage VIH 2.0 OVDD +0.3 V

Input low voltage VIL –0.3 0.8 V

Input current IIN ±5 μA

Output low voltage VOL IOL = 8.0 mA — 0.5 V 2

Output low voltage VOL IOL = 3.2 mA — 0.4 V 2

Notes:

1. This table applies for pins IRQ[0:7], IRQ_OUT, and MCP_OUT.

2. IRQ_OUT and MCP_OUT are open-drain pins; thus VOH is not relevant for those pins.

Table 47. IPIC Input AC Timing Specifications1

Characteristic Symbol2Min Unit

IPIC inputs—minimum pulse width tPICWID 20 ns

Notes:

1. Input specifications are measured at the 50 percent level of the IPIC input signals. Timings are measured at the pin.

2. IPIC inputs and outputs are asynchronous to any visible clock. IPIC outputs should be synchronized before use by external

synchronous logic. IPIC inputs must be valid for at least tPICWID ns to ensure proper operation in edge triggered mode.

Table 48. SPI DC Electrical Characteristics

Characteristic Symbol Condition Min Max Unit

Input high voltage VIH —2.0OV

DD +0.3 V

Input low voltage VIL — –0.3 0.8 V

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 47

SPI

17.2 SPI AC Timing Specifications

Table 49 provides the SPI input and output AC timing specifications.

Figure 32 provides the AC test load for the SPI.

Figure 32. SPI AC Test Load

Input current IIN ——±5μA

Output high voltage VOH IOH = –8.0 mA 2.4 — V

Output low voltage VOL IOL = 8.0 mA — 0.5 V

Output low voltage VOL IOL = 3.2 mA — 0.4 V

Table 49. SPI AC Timing Specifications1

Characteristic Symbol2Min Max Unit

SPI outputs valid—Master mode (internal clock) delay tNIKHOV 6ns

SPI outputs hold—Master mode (internal clock) delay tNIKHOX 0.5 ns

SPI outputs valid—Slave mode (external clock) delay tNEKHOV 8ns

SPI outputs hold—Slave mode (external clock) delay tNEKHOX 2ns

SPI inputs—Master mode (internal clock input setup time tNIIVKH 4ns

SPI inputs—Master mode (internal clock input hold time tNIIXKH 0ns

SPI inputs—Slave mode (external clock) input setup time tNEIVKH 4ns

SPI inputs—Slave mode (external clock) input hold time tNEIXKH 2ns

Notes:

1. Output specifications are measured from the 50 percent level of the rising edge of CLKIN to the 50 percent level of the signal.

Timings are measured at the pin.

2. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for inputs

and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tNIKHOX symbolizes the internal timing

(NI) for the time SPICLK clock reference (K) goes to the high state (H) until outputs (O) are invalid (X).

Table 48. SPI DC Electrical Characteristics (continued)

Characteristic Symbol Condition Min Max Unit

Output Z0 = 50 ΩOVDD/2

RL = 50 Ω

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

48 Freescale Semiconductor

Package and Pin Listings

Figure 33 and Figure 34 represent the AC timings from Table 49. Note that although the specifications

generally reference the rising edge of the clock, these AC timing diagrams also apply when the falling edge

is the active edge.

Figure 33 s hows the SPI timings in slave mode (external clock).

Figure 33. SPI AC Timing in Slave Mode (External Clock) Diagram

Figure 34 shows the SPI timings in master mode (internal clock).

Figure 34. SPI AC Timing in Master Mode (Internal Clock) Diagram

18 Package and Pin Listings

This s ection details package par ameters, pin assignments, and di mensions. The MPC8343EA is available

in a plastic ball grid array (PBGA). See Section 18.1, “Package Parameters for the MPC8343EA PBGA,”

and Section 18.2, “Mechanical Dimensions for the MPC8343EA PBGA.”

18.1 Package Parameters for the MPC8343EA PBGA

The package parameters are as provided in the following list. The package type is 29 mm × 29 mm,

620 plastic ball grid array (PBGA).

Package outline 29 mm × 29 mm

Interconnects 620

Pitch 1.00 mm

Module height (maximum) 2.46 mm

SPICLK (Input)

tNEIXKH

tNEIVKH

tNEKHOX

Input Signals:

SPIMOSI

(See Note)

Output Signals:

SPIMISO

(See Note)

Note: The clock edge is selectable on SPI.

SPICLK (Output)

tNIIXKH

tNIKHOX

Input Signals:

SPIMISO

(See Note)

Output Signals:

SPIMOSI

(See Note)

Note: The clock edge is selectable on SPI.

tNIIVKH

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 49

Package and Pin Listings

Module height (typical) 2.23 mm

Module height (minimum) 2.00 mm

Solder balls 62 Sn/36 Pb/2 Ag (ZQ package)

96.5 Sn/3.5Ag (VR package)

Ball diameter (typical) 0.60 mm

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

50 Freescale Semiconductor

Package and Pin Listings

18.2 Mechanical Dimensions for the MPC8343EA PBGA

Figure 35 shows the mechanical dimensions and bottom surface nomenclature for the MPC8343EA,

620-PBGA package.

Notes:

1. All dimensions are in millimeters.

2. Dimensioning and tolerancing per ASME Y14. 5M-1994.

3. Maximum solder ball diameter measured parallel to datum A.

4. Datum A, the seating plane, is determined by the spherical crowns of the solder balls.

Figure 35. Mechanical Dimensions and Bottom Surface Nomenclature for the MPC8343EA PBGA

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 51

Package and Pin Listings

18.3 Pinout Listings

Table 50 provides the pin-out listing for the MPC8343EA, 620-PBGA package.

Table 50. MPC8343EA (PBGA) Pinout Listing

Signal Package Pin Number Pin Type Power

Supply Notes

PCI

PCI1_INTA/IRQ_OUT D20 O OVDD 2

PCI1_RESET_OUT B21 O OVDD —

PCI1_AD[31:0] E19, D17, A16, A18, B17, B16, D16,

B18, E17, E16, A15, C16, D15, D14,

C14, A12, D12, B11, C11, E12, A10,

C10, A9, E11, E10, B9, B8, D9, A8, C9,

D8, C8

I/O OVDD —

PCI1_C/BE[3:0] A17, A14, A11, B10 I/O OVDD —

PCI1_PAR D13 I/O OVDD —

PCI1_FRAME B14 I/O OVDD 5

PCI1_TRDY A13 I/O OVDD 5

PCI1_IRDY E13 I/O OVDD 5

PCI1_STOP C13 I/O OVDD 5

PCI1_DEVSEL B13 I/O OVDD 5

PCI1_IDSEL C17 I OVDD —

PCI1_SERR C12 I/O OVDD 5

PCI1_PERR B12 I/O OVDD 5

PCI1_REQ[0] A21 I/O OVDD —

PCI1_REQ[1]/CPCI1_HS_ES C19 I OVDD —

PCI1_REQ[2:4] C18, A19, E20 I OVDD —

PCI1_GNT0 B20 I/O OVDD —

PCI1_GNT1/CPCI1_HS_LED C20 O OVDD —

PCI1_GNT2/CPCI1_HS_ENUM B19 O OVDD —

PCI1_GNT[3:4] A20, E18 O OVDD —

M66EN L26 I OVDD —

DDR SDRAM Memory Interface

MDQ[0:31] AC25, AD27, AD25, AH27, AE28, AD26,

AD24, AF27, AF25, AF28, AH24, AG26,

AE25, AG25, AH26, AH25, AG22, AH22,

AE21, AD19, AE22, AF23, AE19, AG20,

AG19, AD17, AE16, AF16, AF18, AG18,

AH17, AH16

I/O GVDD —

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

52 Freescale Semiconductor

Package and Pin Listings

MECC[0:4]/MSRCID[0:4] AG13, AE14, AH12, AH10, AE15 I/O GVDD —

MECC[5]/MDVAL AH14 I/O GVDD —

MECC[6:7] AE13, AH11 I/O GVDD —

MDM[0:3] AG28, AG24, AF20, AG17 O GVDD —

MDM[8] AG12 O GVDD —

MDQS[0:3] AE27, AE26, AE20, AH18 I/O GVDD —

MDQS[8] AH13 I/O GVDD —

MBA[0:1] AF10, AF11 O GVDD —

MA[0:14] AF13, AF15, AG16, AD16, AF17, AH20,

AH19, AH21, AD18, AG21, AD13, AF21,

AF22, AE1, AA5

OGV

DD —

MWE AD10 O GVDD —

MRAS AF7 O GVDD —

MCAS AG6 O GVDD —

MCS[0:3] AE7, AH7, AH4, AF2 O GVDD —

MCKE[0:1] AG23, AH23 O GVDD 3

MCK[0:3] AH15, AE24, AE2, AF14 O GVDD —

MCK[0:3] AG15, AD23, AE3, AG14 O GVDD —

MODT[0:3] AG5, AD4, AH6, AF4 O GVDD —

MBA[2] AD22 O GVDD —

MDIC0 AG11 I/O — 9

MDIC1 AF12 I/O — 9

Local Bus Controller Interface

LAD[0:31] T4, T5, T1, R2, R3, T2, R1, R4, P1, P2,

P3, P4, N1, N4, N2, N3, M1, M2, M3, N5,

M4, L1, L2, L3, K1, M5, K2, K3, J1, J2,

L5, J3

I/O OVDD —

LDP[0]/CKSTOP_OUT H1 I/O OVDD —

LDP[1]/CKSTOP_IN K5 I/O OVDD —

LDP[2]/LCS[4] H2 I/O OVDD —

LDP[3]/LCS[5] G1 I/O OVDD —

LA[27:31] J4, H3, G2, F1, G3 O OVDD —

LCS[0:3] J5, H4, F2, E1 O OVDD —

LWE[0:3]/LSDDQM[0:3]/LBS[0:3] F3, G4, D1, E2 O OVDD —

Table 50. MPC8343EA (PBGA) Pinout Listing (continued)

Signal Package Pin Number Pin Type Power

Supply Notes

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 53

Package and Pin Listings

LBCTL H5 O OVDD —

LALE E3 O OVDD —

LGPL0/LSDA10/cfg_reset_source0 F4 I/O OVDD —

LGPL1/LSDWE/cfg_reset_source1 D2 I/O OVDD —

LGPL2/LSDRAS/LOE C1 O OVDD —

LGPL3/LSDCAS/cfg_reset_source2 C2 I/O OVDD —

LGPL4/LGTA/LUPWAIT/LPBSE C3 I/O OVDD —

LGPL5/cfg_clkin_div B3 I/O OVDD —

LCKE E4 O OVDD —

LCLK[0:2] D4, A3, C4 O OVDD —

LSYNC_OUT U3 O OVDD —

LSYNC_IN Y2 I OVDD —

General Purpose I/O Timers

GPIO1[0]/DMA_DREQ0/GTM1_TIN1/

GTM2_TIN2

D27 I/O OVDD —

GPIO1[1]/DMA_DACK0/GTM1_TGATE1/

GTM2_TGATE2

E26 I/O OVDD —

GPIO1[2]/DMA_DDONE0/

GTM1_TOUT1

D28 I/O OVDD —

GPIO1[3]/DMA_DREQ1/GTM1_TIN2/

GTM2_TIN1

G25 I/O OVDD —

GPIO1[4]/DMA_DACK1/

GTM1_TGATE2/GTM2_TGATE1

J24 I/O OVDD —

GPIO1[5]/DMA_DDONE1/

GTM1_TOUT2/GTM2_TOUT1

F26 I/O OVDD —

GPIO1[6]/DMA_DREQ2/GTM1_TIN3/

GTM2_TIN4

E27 I/O OVDD —

GPIO1[7]/DMA_DACK2/GTM1_TGATE3/

GTM2_TGATE4

E28 I/O OVDD —

GPIO1[8]/DMA_DDONE2/

GTM1_TOUT3

H25 I/O OVDD —

GPIO1[9]/DMA_DREQ3/GTM1_TIN4/

GTM2_TIN3

F27 I/O OVDD —

GPIO1[10]/DMA_DACK3/

GTM1_TGATE4/GTM2_TGATE3

K24 I/O OVDD —

GPIO1[11]/DMA_DDONE3/

GTM1_TOUT4/GTM2_TOUT3

G26 I/O OVDD —

Table 50. MPC8343EA (PBGA) Pinout Listing (continued)

Signal Package Pin Number Pin Type Power

Supply Notes

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

54 Freescale Semiconductor

Package and Pin Listings

USB

DR_D0_ENABLEN C28 I/O OVDD —

DR_D1_SER_TXD F25 I/O OVDD —

DR_D2_VMO_SE0 B28 I/O OVDD —

DR_D3_SPEED C27 I/O OVDD —

DR_D4_DP D26 I/O OVDD —

DR_D5_DM E25 I/O OVDD —

DR_D6_SER_RCV C26 I/O OVDD —

DR_D7_DRVVBUS D25 I/O OVDD —

DR_SESS_VLD_NXT B26 I OVDD —

DR_XCVR_SEL_DPPULLUP E24 I/O OVDD —

DR_STP_SUSPEND A27 O OVDD —

DR_RX_ERROR_PWRFAULT C25 I OVDD —

DR_TX_VALID_PCTL0 A26 O OVDD —

DR_TX_VALIDH_PCTL1 B25 O OVDD —

DR_CLK A25 I OVDD —

Programmable Interrupt Controller

MCP_OUT E8 O OVDD 2

IRQ0/MCP_IN/GPIO2[12] J28 I/O OVDD —

IRQ[1:5]/GPIO2[13:17] K25, J25, H26, L24, G27 I/O OVDD —

IRQ[6]/GPIO2[18]/CKSTOP_OUT G28 I/O OVDD —

IRQ[7]/GPIO2[19]/CKSTOP_IN J26 I/O OVDD —

Ethernet Management Interface

EC_MDC Y24 O LVDD1 —

EC_MDIO Y25 I/O LVDD1 2

Gigabit Reference Clock

EC_GTX_CLK125 Y26 I LVDD1 —

Three-Speed Ethernet Controller (Gigabit Ethernet 1)

TSEC1_COL/GPIO2[20] M26 I/O OVDD —

TSEC1_CRS/GPIO2[21] U25 I/O LVDD1 —

TSEC1_GTX_CLK V24 O LVDD1 3

TSEC1_RX_CLK U26 I LVDD1 —

Table 50. MPC8343EA (PBGA) Pinout Listing (continued)

Signal Package Pin Number Pin Type Power

Supply Notes

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 55

Package and Pin Listings

TSEC1_RX_DV U24 I LVDD1 —

TSEC1_RX_ER/GPIO2[26] L28 I/O OVDD —

TSEC1_RXD[3:0] W26, W24, Y28, Y27 I LVDD1 —

TSEC1_TX_CLK N25 I OVDD —

TSEC1_TXD[3:0] V28, V27, V26, W28 O LVDD1 10

TSEC1_TX_EN W27 O LVDD1 —

TSEC1_TX_ER/GPIO2[31] N24 I/O OVDD —

Three-Speed Ethernet Controller (Gigabit Ethernet 2)

TSEC2_COL/GPIO1[21] P28 I/O OVDD —

TSEC2_CRS/GPIO1[22] AC28 I/O LVDD2 —

TSEC2_GTX_CLK AC27 O LVDD2 —

TSEC2_RX_CLK AB25 I LVDD2 —

TSEC2_RX_DV/GPIO1[23] AC26 I/O LVDD2 —

TSEC2_RXD[3:0]/GPIO1[13:16] AA25, AA26, AA27, AA28 I/O LVDD2 —

TSEC2_RX_ER/GPIO1[25] R25 I/O OVDD —

TSEC2_TXD[3:0]/GPIO1[17:20] AB26, AB27, AA24, AB28 I/O LVDD2 —

TSEC2_TX_ER/GPIO1[24] R27 I/O OVDD —

TSEC2_TX_EN/GPIO1[12] AD28 I/O LVDD2 3

TSEC2_TX_CLK/GPIO1[30] R26 I/O OVDD —

DUART

UART_SOUT[1:2]/MSRCID[0:1]/

LSRCID[0:1]

B4, A4 O OVDD —

UART_SIN[1:2]/MSRCID[2:3]/

LSRCID[2:3]

D5, C5 I/O OVDD —

UART_CTS[1]/MSRCID4/LSRCID4 B5 I/O OVDD —

UART_CTS[2]/MDVAL/LDVAL A5 I/O OVDD —

UART_RTS[1:2] D6, C6 O OVDD —

I2C interface

IIC1_SDA E5 I/O OVDD 2

IIC1_SCL A6 I/O OVDD 2

IIC2_SDA B6 I/O OVDD 2

IIC2_SCL E7 I/O OVDD 2

Table 50. MPC8343EA (PBGA) Pinout Listing (continued)

Signal Package Pin Number Pin Type Power

Supply Notes

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

56 Freescale Semiconductor

Package and Pin Listings

SPI

SPIMOSI/LCS[6] D7 I/O OVDD —

SPIMISO/LCS[7] C7 I/O OVDD —

SPICLK B7 I/O OVDD —

SPISEL A7 I OVDD —

Clocks

PCI_CLK_OUT[0:2] Y1, W3, W2 O OVDD —

PCI_CLK_OUT[3]/LCS[6] W1 O OVDD —

PCI_CLK_OUT[4]/LCS[7] V3 O OVDD —

PCI_SYNC_IN/PCI_CLOCK U4 I OVDD —

PCI_SYNC_OUT U5 O OVDD 3

RTC/PIT_CLOCK E9 I OVDD —

CLKIN W5 I OVDD —

JTAG

TCK H27 I OVDD —

TDI H28 I OVDD 4

TDO M24 O OVDD 3

TMS J27 I OVDD 4

TRST K26 I OVDD 4

Test

TEST F28 I OVDD 6

TEST_SEL T3 I OVDD 7

PMC

QUIESCE K27 O OVDD —

System Control

PORESET K28 I OVDD —

HRESET M25 I/O OVDD 1

SRESET L27 I/O OVDD 2

Thermal Management

THERM0 B15 I — 8

Table 50. MPC8343EA (PBGA) Pinout Listing (continued)

Signal Package Pin Number Pin Type Power

Supply Notes

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 57

Package and Pin Listings

Power and Ground Signals

AVDD1 C15 Power for e300

PLL (1.2 V)

AVDD1—

AVDD2 U1 Power for

system PLL

(1.2 V)

AVDD2—

AVDD3 AF9 Power for DDR

DLL (1.2 V)

——

AVDD4 U2 Power for LBIU

DLL (1.2 V)

AVDD4—

GND A2, B1, B2, D10, D18, E6, E14, E22, F9,

F12, F15, F18, F21, F24, G5, H6, J23,

L4, L6, L12, L13, L14, L15, L16, L17,

M11, M12, M13, M14, M15, M16, M17,

M18, M23, N11, N12, N13, N14, N15,

N16, N17, N18, P6, P11, P12, P13, P14,

P15, P16, P17, P18, P24, R5, R23, R11,

R12, R13, R14, R15, R16, R17, R18,

T11, T12, T13, T14, T15, T16, T17, T18,

U6, U11, U12, U13, U14, U15, U16,

U17, U18, V12, V13, V14, V15, V16,

V17, V23, V25, W4, Y6, AA23, AB24,

AC5, AC8, AC11, AC14, AC17, AC20,

AD9, AD15, AD21, AE12, AE18, AF3,

AF26

———

GVDD U9, V9, W10, W19, Y11, Y12, Y14, Y15,

Y17, Y18, AA6, AB5, AC9, AC12, AC15,

AC18, AC21, AC24, AD6, AD8, AD14,

AD20, AE5, AE11, AE17, AG2, AG27

Power for DDR

DRAM I/O

voltage

(2.5 V)

GVDD —

LVDD1 U20, W25 Power for three

speed Ethernet

#1 and for

Ethernet

management

interface I/O

(2.5V, 3.3V)

LVDD1 —

LVDD2 V20, Y23 Power for three

speed Ethernet

#2 I/O (2.5 V,

3.3 V)

LVDD2 —

VDD J11, J12, J15, K10, K11, K12, K13, K14,

K15, K16, K17, K18, K19, L10, L11, L18,

L19, M10, M19, N10, N19, P9, P10, P19,

R10, R19, R20, T10, T19, U10, U19,

V10, V11, V18, V19, W11, W12, W13,

W14, W15, W16, W17, W18

Power for core

(1.2 V)

VDD —

Table 50. MPC8343EA (PBGA) Pinout Listing (continued)

Signal Package Pin Number Pin Type Power

Supply Notes

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

58 Freescale Semiconductor

Package and Pin Listings

OVDD B27, D3, D11, D19, E15, E23, F5, F8,

F11, F14, F17, F20, G24, H23, H24, J6,

J14, J17, J18, K4, L9, L20, L23, L25, M6,

M9, M20, P5, P20, P23, R6, R9, R24,

U23, V4, V6

PCI, 10/100

Ethernet, and

other standard

(3.3 V)

OVDD —

MVREF1 AF19 I DDR

reference

voltage

—

MVREF2 AE10 I DDR

reference

voltage

—

No Connection

NC A22, A23, A24, B22, B23, B24, C21,

C22, C23, C24, D21, D22, D23, D24,

E21, M27, M28, N26, N27, N28, P25,

P26, P27, R28, T24, T25, T26, T27, T28,

U27, U28, Y3, Y4, Y5, AA1, AA2, AA3,

AA4, AB1, AB2, AB3, AB4, AC1, AC2,

AC3, AC4, AD1, AD2, AD3, AD5, AD7,

AD11, AD12, AE4, AE6, AE8, AE9,

AE23, AF1, AF5, AF6, AF8, AF24, AG1,

AG3, AG4, AG7, AG8, AG9, AG10, AH2,

AH3, AH5, AH8, AH9, V5, V2, V1

———

Notes:

1. This pin is an open-drain signal. A weak pull-up resistor (1 kΩ) should be placed on this pin to OVDD.

2. This pin is an open-drain signal. A weak pull-up resistor (2–10 kΩ) should be placed on this pin to OVDD.

3. During reset, this output is actively driven rather than three-stated.

4. These JTAG pins have weak internal pull-up P-FETs that are always enabled.

5. This pin should have a weak pull-up if the chip is in PCI host mode. Follow the PCI specifications.

6. This pin must be always be tied to GND.

7. This pin must always be pulled up to OVDD

8. Thermal sensitive resistor.

9. It is recommended that MDIC0 be tied to GND using an 18.2 Ω resistor and MDIC1 be tied to DDR power using an 18.2 Ω

resistor.

10.TSEC1_TXD[3] is required an external pull-up resistor. For proper functionality of the device, this pin must be pulled up or

actively driven high during a hard reset. No external pull-down resistors are allowed to be attached to this net.

Table 50. MPC8343EA (PBGA) Pinout Listing (continued)

Signal Package Pin Number Pin Type Power

Supply Notes

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 59

Clocking

19 Clocking

Figure 36 shows the internal distribution of the clocks.

Figure 36. MPC8343EA Clock Subsystem

The primary clock source can be one of two inputs, CLKIN or PCI_CLK, depending on whether the device

is configured in PCI host or PCI agent mode. When the MPC8343EA is configured as a PCI h ost device,

CLKIN is its primary input cl ock. CLKIN feeds the PCI clock divider (÷2) and the multiplexors for

PCI_SYNC_OUT and PCI_CLK_OUT. The CFG_CLKIN_DIV configuration input selects whether

CLKIN or CLKIN/2 is driven out on the PCI_SYNC_OUT signal. The OCCR[PCICDn] parameters select

whether CLKIN or CLKIN/2 is driven out on the P CI_CL K_OUTn signals.

PCI_SYNC_OUT is connected externally to PCI_SYNC_IN to allow the internal clock subsystem to

synchronize to the system PCI clocks. PCI_SYNC_OUT must be connected properly to PCI_SYNC_IN,

with equal delay to all PCI agent devices in the system, to allow the MPC8343EA to function. When the

MPC8343EA is configured as a PCI agent device, PCI_CLK is the primary input clock and the CLKIN

signal should be tied to GND.

Core PLL

System PLL

DDR

LBIU

LSYNC_IN

LSYNC_OUT

LCLK[0:2]

MCK[0:3]

core_clk

e300 Core

csb_clk

to Rest

CLKIN

csb_clk

MPC8343EA

DDR

Memory

Local Bus

PCI_CLK_OUT[0:4]

PCI_SYNC_OUT

PCI_CLK/

Clock

Unit

of the Device

ddr_clk

lbiu_clk

CFG_CLKIN_DIV

PCI Clock

PCI_SYNC_IN

Device

Memory

Device

To Lo c a l B u s

Memory

Controller

To DDR

Memory

Controller

DLL

Clock

Div

Divider

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

60 Freescale Semiconductor

Clocking

As shown in Figure 36, the primary clock input (frequency) is multiplied up by the system phase-locked

loop (PLL) and the clock unit to create the coherent system bus clock (csb_clk), the internal cl ock for the

DDR controller (ddr_clk), and the internal clock for the local bus interf ace unit (lbiu_clk).

The csb_clk frequency is derived from a complex set of factors that can be simplified into the following

equation:

csb_clk = {PCI_SYNC_IN × (1 + CFG_CLKIN_DIV)} × SPMF

In PCI host mode, PCI_SYNC_I N × (1 + CFG_CLKIN_DIV) is the CLKIN frequency.

The csb_clk serves as the cloc k input to the e300 core. A second PLL inside the e300 cor e multiplies the

csb_clk frequency to create the internal clock for the e300 core (core_clk). The system and core PLL

multiplie rs a re s e lect ed by the SPMF and COR EPLL fie lds in the re set c onfigura tion word low (R C WL),

which is loaded at pow er-on reset or by one of the har d- coded reset options. See the chapter on reset,

clocking, and initialization in the MPC8349EA Reference Manual for more information on the clock

subsystem.

The internal ddr_clk frequency is determined by the following equation:

ddr_clk = csb_clk × (1 + RCWL[DD RCM])

ddr_clk is not the external memory bus frequency; ddr_clk passes through the DDR clock divider (÷2) to

create the differential DDR memory bus clock outputs (MCK and MCK). However, the data rate is the

same frequency as ddr_clk.

The internal lbiu_clk frequency is determined by the following equation:

lbiu_clk = csb_clk × (1 + RCWL[LBIUCM])

lbiu_clk is not the external local bus frequency; lbiu_clk passes through the LBIU clock divider to create

the external local bus cl ock outputs (LSYNC_OUT and LCLK[0:2]). The LBIU clock divider ratio is

controlled by LCCR[CLKDIV].

In addition, some of the internal units may have to be shut off or operate at lower frequency than the

csb_clk frequency. Those units have a default clock ratio that can be configured by a memory-mapped

Table 51. Configurable Clock Units

Unit Default

Frequency Options

TSEC1

csb_clk/3

Off,

csb_clk, csb_clk/2, csb_clk/3

TSEC2, I2C1

csb_clk/3

Off,

csb_clk, csb_clk/2, csb_clk/3

Security core

csb_clk/3

Off,

csb_clk,

csb_clk/2,

csb_clk/3

USB DR, USB MPH

csb_clk/3

Off, csb_clk, csb_clk/2,

csb_clk/3

PCI and DMA complex

csb_clk

Off,

csb_clk

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 61

Clocking

Table 52 provides the operating frequencies for the MPC8343EA PBGA under recommended operating

conditions.

19.1 System PLL Configuration

The system PLL is controlled by the RCWL[SPMF] parameter. Table 53 shows the multiplica tion factor

encodings for the syst em PLL.

Table 52. Operating Frequencies for PBGA

Characteristic1

1The CLKIN frequency, RCWL[SPMF], and RCWL[COREPLL] settings must be chosen so that the resulting

csb_clk

, MCLK,

LCLK[0:2], and

core_clk

frequencies do not exceed their respective maximum or minimum operating frequencies. The value

of SCCR[ENCCM], SCCR[USBDRCM], and SCCR[USBMPHCM] must be programmed so that the maximum internal

operating frequency of the Security core and USB modules does not exceed the respective values listed in this table.

266 MHz 333 MHz 400 MHz Unit

e300 core frequency (

core_clk

) 200–266 200–333 200–400 MHz

Coherent system bus frequency (

csb_clk

) 100–266 MHz

DDR1 memory bus frequency (MCK)2

2The DDR data rate is 2x the DDR memory bus frequency.

100–133 MHz

DDR2 memory bus frequency (MCK)3

3The DDR data rate is 2x the DDR memory bus frequency.

100–133 MHz

Local bus frequency (LCLK

4The local bus frequency is 1/2, 1/4, or 1/8 of the

lbiu_clk

frequency (depending on LCCR[CLKDIV]) which is in turn 1x or 2x

the

csb_clk

frequency (depending on RCWL[LBIUCM]).

16.67–133 MHz

PCI input frequency (CLKIN or PCI_CLK) 25–66 MHz

Security core maximum internal operating frequency 133 MHz

USB_DR, USB_MPH maximum internal operating

frequency

133 MHz

Table 53. System PLL Multiplication Factors

RCWL[SPMF] System PLL Multiplication

Factor

0000 × 16

0001 Reserved

0010 × 2

0011 × 3

0100 × 4

0101 × 5

0110 × 6

0111 × 7

1000 × 8

1001 × 9

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

62 Freescale Semiconductor

Clocking

As described in Section 19, “Clocking,” the LBIUCM, DDRCM, and SPMF paramete rs in the reset

configuration word low and the CFG_CLKIN_DIV configuration input signal select the ratio between the

primary clock input (CLKIN or PCI_CLK) and the internal coherent system bus clock (csb_clk). Table 54

and Table 55 show the expected frequency values for the CSB frequency for select csb_clk to

CLKIN/PCI_SYNC_I N ratios.

1010 × 10

1011 × 11

1100 × 12

1101 × 13

1110 × 14

1111 × 15

Table 54. CSB Frequency Options for Host Mode

CFG_CLKIN_DIV

at Reset1SPMF

csb_clk

Input Clock

Ratio2

Input Clock Frequency (MHz)2

16.67 25 33.33 66.67

csb_clk

Frequency (MHz)

Low 0010 2 : 1 133

Low 0011 3 : 1 100 200

Low 0100 4 : 1 100 133 266

Low 0101 5 : 1 125 166 333

Low 0110 6 : 1 100 150 200

Low 0111 7 : 1 116 175 233

Low 1000 8 : 1 133 200 266

Low 1001 9 : 1 150 225 300

Low 1010 10 : 1 166 250 333

Low 1011 11 : 1 183 275

Low 1100 12 : 1 200 300

Low 1101 13 : 1 216 325

Low 1110 14 : 1 233

Low 1111 15 : 1 250

Low 0000 16 : 1 266

Table 53. System PLL Multiplication Factors (continued)

RCWL[SPMF] System PLL Multiplication

Factor

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 63

Clocking

High 0010 2 : 1 133

High 0011 3 : 1 100 200

High 0100 4 : 1 133 266

High 0101 5 : 1 166 333

High 0110 6 : 1 200

High 0111 7 : 1 233

High 1000 8 : 1

1CFG_CLKIN_DIV selects the ratio between CLKIN and PCI_SYNC_OUT.

2CLKIN is the input clock in host mode; PCI_CLK is the input clock in agent mode.

DDR2 memory may be used at 133 MHz provided that the memory components are specified for operation

at this frequency.

Table 55. CSB Frequency Options for Agent Mode

CFG_CLKIN_DIV

at Reset1SPMF

csb_clk

Input Clock

Ratio2

Input Clock Frequency (MHz)2

16.67 25 33.33 66.67

csb_clk

Frequency (MHz)

Low 0010 2 : 1 133

Low 0011 3 : 1 100 200

Low 0100 4 : 1 100 133 266

Low 0101 5 : 1 125 166 333

Low 0110 6 : 1 100 150 200

Low 0111 7 : 1 116 175 233

Low 1000 8 : 1 133 200 266

Low 1001 9 : 1 150 225 300

Low 1010 10 : 1 166 250 333

Low 1011 11 : 1 183 275

Low 1100 12 : 1 200 300

Low 1101 13 : 1 216 325

Low 1110 14 : 1 233

Low 1111 15 : 1 250

Low 0000 16 : 1 266

Table 54. CSB Frequency Options for Host Mode (continued)

CFG_CLKIN_DIV

at Reset1SPMF

csb_clk

Input Clock

Ratio2

Input Clock Frequency (MHz)2

16.67 25 33.33 66.67

csb_clk

Frequency (MHz)

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

64 Freescale Semiconductor

Clocking

19.2 Core PLL Configuration

RCWL[COREPLL] selects the ratio between the internal coherent system bus clock (csb_clk) and the e300

core clock (core_clk). Table 56 shows the encodings f or RCWL [ CORE P LL]. CORE PLL values that are

not listed in Table 56 should be considered as reserved.

NOTE

Core VCO frequency = core frequency × VCO divider

VCO divider must be set properly so that the core VCO frequency is in the

range of 800–1800 MHz.

High 0010 4 : 1 100 133 266

High 0011 6 : 1 100 150 200

High 0100 8 : 1 133 200 266

High 0101 10 : 1 166 250 333

High 0110 12 : 1 200 300

High 0111 14 : 1 233

High 1000 16 : 1 266

1CFG_CLKIN_DIV doubles csb_clk if set high.

2CLKIN is the input clock in host mode; PCI_CLK is the input clock in agent mode.

DDR2 memory may be used at 133 MHz provided that the memory components are specified for operation

at this frequency.

Table 56. e300 Core PLL Configuration

RCWL[COREPLL]

core_clk

csb_clk

Ratio VCO Divider1

0–1 2–5 6

nn 0000 n PLL bypassed

(PLL off,

csb_clk

clocks core directly)

PLL bypassed

(PLL off,

csb_clk

clocks core directly)

00 0001 01:1 2

01 0001 01:1 4

10 0001 01:1 8

11 0001 01:1 8

00 0001 11.5:1 2

01 0001 11.5:1 4

10 0001 11.5:1 8

Table 55. CSB Frequency Options for Agent Mode (continued)

CFG_CLKIN_DIV

at Reset1SPMF

csb_clk

Input Clock

Ratio2

Input Clock Frequency (MHz)2

16.67 25 33.33 66.67

csb_clk

Frequency (MHz)

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 65

Clocking

19.3 Suggested PLL Configurations

Table 57 shows suggested PLL configurations for 33 and 66 MHz input clocks, when CFG_CLKIN_DIV

is low at reset.

11 0001 11.5:1 8

00 0010 02:1 2

01 0010 02:1 4

10 0010 02:1 8

11 0010 02:1 8

00 0010 12.5:1 2

01 0010 12.5:1 4

10 0010 12.5:1 8

11 0010 12.5:1 8

00 0011 03:1 2

01 0011 03:1 4

10 0011 03:1 8

11 0011 03:1 8

1Core VCO frequency = core frequency × VCO divider. The VCO divider must be set properly so that the core VCO frequency

is in the range of 800–1800 MHz.

Table 57. Suggested PLL Configurations

Ref

No.1

RCWL 266 MHz Device 333 MHz Device 400 MHz Device

SPMF CORE

PLL

Input

Clock

Freq

(MHz)2

CSB

Freq

(MHz)

Core

Freq

(MHz)

Input

Clock

Freq

(MHz)2

CSB

Freq

(MHz)

Core

Freq

(MHz)

Input

Clock

Freq

(MHz)2

CSB

Freq

(MHz)

Core

Freq

(MHz)

33 MHz CLKIN/PCI_CLK Options

343 0011 1000011 33 100 150 33 100 150 33 100 150

324 0011 0100100 33 100 200 33 100 200 33 100 200

423 0100 0100011 33 133 200 33 133 200 33 133 200

622 0110 0100010 33 200 200 33 200 200 33 200 200

523 0101 0100011 33 166 250 33 166 250 33 166 250

424 0100 0100100 33 133 266 33 133 266 33 133 266

822 1000 0100010 33 266 266 33 266 266 33 266 266

Table 56. e300 Core PLL Configuration (continued)

RCWL[COREPLL]

core_clk

csb_clk

Ratio VCO Divider1

0–1 2–5 6

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

66 Freescale Semiconductor

Clocking

326 0011 0100110 — 33 100 300 33 100 300

623 0110 0100011 — 33 200 300 33 200 300

922 1001 0100010 — 33 300 300 33 300 300

425 0100 0100101 — 33 133 333 33 133 333

524 0101 0100100 — 33 166 333 33 166 333

A22 1010 0100010 — 33 333 333 33 333 333

723 0111 0100011 — — 33 233 350

604 0110 0000100 — — 33 200 400

624 0110 0100100 — — 33 200 400

823 1000 0100011 — — 33 266 400

66 MHz CLKIN/PCI_CLK Options

242 0010 1000010 66 133 133 66 133 133 66 133 133

322 0011 0100010 66 200 200 66 200 200 66 200 200

224 0010 0100100 66 133 266 66 133 266 66 133 266

422 0100 0100010 66 266 266 66 266 266 66 266 266

323 0011 0100011 — 66 200 300 66 200 300

223 0010 0100101 — 66 133 333 66 133 333

522 0101 0100010 — 66 333 333 66 333 333

304 0011 0000100 — — 66 200 400

324 0011 0100100 — — 66 200 400

403 0100 0000011 — — 66 266 400

423 0100 0100011 — — 66 266 400

1The PLL configuration reference number is the hexadecimal representation of RCWL, bits 4–15 associated with the SPMF

and COREPLL settings given in the table.

2The input clock is CLKIN for PCI host mode or PCI_CLK for PCI agent mode.

Table 57. Suggested PLL Configurations (continued)

Ref

No.1

RCWL 266 MHz Device 333 MHz Device 400 MHz Device

SPMF CORE

PLL

Input

Clock

Freq

(MHz)2

CSB

Freq

(MHz)

Core

Freq

(MHz)

Input

Clock

Freq

(MHz)2

CSB

Freq

(MHz)

Core

Freq

(MHz)

Input

Clock

Freq

(MHz)2

CSB

Freq

(MHz)

Core

Freq

(MHz)

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 67

Thermal

20 Thermal

This section describes the thermal specifications of the MPC8343EA.

20.1 Thermal Characteristics

.Table 58 provides the package thermal characteristics for the 620 29 ×29 mm PBGA of the MPC8343EA.

20.2 Thermal Management Information

For the following sections, PD = (VDD ×IDD) + PI/O where PI/O is the p ower dissipation of the I/O drivers.

See Table 5 for I/O power dissipation values.

20.2.1 Estimation of Junction Temperature with Junction-to-Ambient

Thermal Resistance

An estimation of the chip junction t emperat ure, TJ, can be obtained from the equation:

TJ = TA + (R

JA × PD)

where:

TJ = junction temperature (°C)

TA = ambient tempera t ure for the package (°C)

JA = junction-to-ambient thermal resistance (°C/W)

PD = power dissipation in the package (W)

Table 58. Package Thermal Characteristics for PBGA

Characteristic Symbol Value Unit Notes

Junction-to-ambient natural convection on single-layer board (1s) RθJA 21 °C/W 1, 2

Junction-to-ambient natural convection on four-layer board (2s2p) RθJMA 15 °C/W 1, 3

Junction-to-ambient (@ 200 ft/min) on single-layer board (1s) RθJMA 17 °C/W 1, 3

Junction-to-ambient (@ 200 ft/min) on four-layer board (2s2p) RθJMA 12 °C/W 1, 3

Junction-to-board thermal RθJB 6°C/W 4

Junction-to-case thermal RθJC 5°C/W 5

Junction-to-package natural convection on top ψJT 5°C/W 6

Notes

1. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board)

temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal

resistance.

2. Per SEMI G38-87 and JEDEC JESD51-2 with the single-layer board horizontal.

3. Per JEDEC JESD51-6 with the board horizontal.

4. Thermal resistance between the die and the printed-circuit board per JEDEC JESD51-8. Board temperature is measured on

the top surface of the board near the package.

5. Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883 Method

1012.1).

6. Thermal characterization parameter indicating the temperature difference between package top and the junction temperature

per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written as Psi-JT.

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

68 Freescale Semiconductor

Thermal

The junction-to-ambient thermal resistance is an industry-standard value that provides a quick and easy

estimation of therm al perfo rmance. Generally, the value obtained on a single-layer boar d is appropriate for

a tightly packed printed-circuit board. The value obtained on the board with the internal planes is usually

appropriate if the board has low power dissipation and the components are well separated. T est cases have

demonstra ted that errors of a factor of two (in the quantity TJ–T

A) are possible.

20.2.2 Estimation of Junction Temperature with Junction-to-Board

Thermal Resistance

The thermal performance of a device cannot be adequately predicted from the junction-to-ambient thermal

resistance. The thermal performance of any component is s trongly dependent on the power dissipation of

surrounding components. In addition, the ambient temperature varies widely within the application. For

many natural convection and especially closed box applications, the board temperature at the perimeter

(edge) of the package is approximately the same as the local air temperatur e near the device. Specifying

the local ambient conditions explicitly a s the board temperature provides a more precise description of the

local ambient conditions that determine the temperature of the device.

At a known board temperature, the junction temperature is estimated using the following equation:

TJ = TA + (R

JA × PD)

where:

TJ = junction temperature (°C)

TA = ambient tempera t ure for the package (°C)

JA = junction-to-ambient thermal resistance (°C/W)

PD = power dissipation in the package (W)

When the heat loss from the package case to the air can be ignored, acceptable predictions of junction

temperature can be made. The application board should be similar to the thermal test condition: the

component is sol dered to a board with internal planes.

20.2.3 Experimental Determination of Junction Temperature

To determine the junction temperature of the device in the application after prototypes are available, use

the thermal char acterization parame ter (

JT) to determine the junction tem perature and a measure of the

temperature at the top center of the package case using the following equation:

TJ = TT + (

JT × PD)

where:

TJ = junction temperature (°C)

TT = thermocouple temperature on top of package (°C)

JT = junction-to-ambient thermal resistance (°C/W)

PD = power dissipation in the package (W)

The thermal characterization parameter is measured per the JESD51-2 specification using a 40 gauge type

T thermocouple epoxied to the top center of the package case. The thermocouple should be positioned s o

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 69

Thermal

that the thermocouple junction rests on the package. A small amount of epoxy is placed over the

thermocouple junction and over about 1 mm of wire extending from the junction. The thermocouple wire

is placed flat against the package case to avoid measurement er rors caus ed by cooling effects of the

thermocoup le wire.

20.2.4 Heat Sinks and Junction-to-Case Thermal Resistance

Some application environments require a heat sink to provide the necessary thermal management of the

device. When a heat sink is used, the thermal resistance is expressed as the sum of a junction-to-case

ther mal resist ance and a case-to-a mbient therma l resista nce:

JA = R

JC + R

where:

JA = junction-to-ambient thermal resistance (°C/W)

JC = junction-to-case thermal resistance (°C/W)

CA = case-to-ambient thermal resistance (°C/W)

JC is device-related and cannot be influenced by the user. The user controls the thermal environment to

change the case-to-ambient thermal resistance, R

CA. For instance, the user can change the size of the heat

sink, the air flow around the device, the interface material, the mounting arrangement on printed-circuit

board, or change the thermal dissipation on the printed-circuit board surrounding the device.

The thermal performance of devices with heat sinks has been simulated with a few commercially available

heat sinks. The heat sink choice is determined by the application environment (temperature, air flow,

adjacent component power dissipation) and the physical space available . Because there is not a standard

application environment, a standard heat sink is not required.

Table 59 shows heat sink thermal resistance for PBGA of the MPC8343EA.

fTable 59. Heat Sink and Thermal Resistance of MPC8343EA (PBGA)

Heat Sink Assuming Thermal Grease Air Flow

29 ×29 mm PBGA

Thermal Resistance

AAVID 30 ×30 ×9.4 mm pin fin Natural convection 13.5

AAVID 30 ×30 ×9.4 mm pin fin 1 m/s 9.6

AAVID 30 ×30 ×9.4 mm pin fin 2 m/s 8.8

AAVID 31 ×35 ×23 mm pin fin Natural convection 11.3

AAVID 31 ×35 ×23 mm pin fin 1 m/s 8.1

AAVID 31 ×35 ×23 mm pin fin 2 m/s 7.5

Wakefield, 53 ×53 ×25 mm pin fin Natural convection 9.1

Wakefield, 53 ×53 ×25 mm pin fin 1 m/s 7.1

Wakefield, 53 ×53 ×25 mm pin fin 2 m/s 6.5

MEI, 75 ×85 ×12 no adjacent board, extrusion Natural convection 10.1

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

70 Freescale Semiconductor

Thermal

Accurate thermal design requires thermal modeling of the application environment using computational

fluid dynamics software which can model both the conduction cooling and the convection cooling of the

air moving through the application. Simplified thermal models of the packages can be assembled using the

junction-to-c a se and junction-to-boa rd thermal re si stance s listed in the thermal resistance table. More

detailed thermal models can be made available on request.

Heat sink vendors include the following list:

Aavid Thermalloy 603-224-9988

80 Commercial St.

Concord, NH 03301

Internet: www.aavidthermalloy.com

Alpha Novatech 408-567-8082

473 Sapena Ct. #12

Santa Clara, CA 95054

Internet: www.alphanovatech.com

International Electronic Research Corporation (IERC) 818-842-7277

413 North Moss St.

Burbank, CA 91502

Internet: www.ctscorp.com

Millennium Electronics (MEI) 408-436-8770

Loroco Sites

671 East Brokaw Road

San Jose, CA 95112

Internet: www.mei-thermal.com

Tyco Electronics 800-522-2800

Chip Coolers™

P.O. Box 3668

Harrisbur g, PA 17105-3668

Internet: www.chipcoolers.com

Wakefield Engineering 603-635-5102

33 Bridge St.

Pelham, NH 03076

Internet: www.wakefield.com

MEI, 75 ×85 ×12 no adjacent board, extrusion 1 m/s 7.7

MEI, 75 ×85 ×12 no adjacent board, extrusion 2 m/s 6.6

MEI, 75 ×85 ×12 mm, adjacent board, 40 mm side bypass 1 m/s 6.9

Table 59. Heat Sink and Thermal Resistance of MPC8343EA (PBGA) (continued)

Heat Sink Assuming Thermal Grease Air Flow

29 ×29 mm PBGA

Thermal Resistance

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 71

Thermal

Interface material vendors include the following:

Chomerics, Inc. 781-935-4850

77 Dragon Ct.

Wobur n, MA 01801

Internet: www.chomerics.com

Dow-Corning Corporat ion 800-248-2481

Dow-Corning Electronic Materials

P.O. Box 994

Midland, MI 48686-0997

Internet: www.dowcorning.com

Shin-Etsu MicroSi, Inc. 888-642-7674

10028 S. 51st St.

Phoenix, AZ 85044

Internet: www.microsi.com

The Bergquist Company 800-347-4572

18930 West 78th St.

Chanhassen, MN 55317

Internet: www.bergquistcompany. com

20.3 Heat Sink Attachment

When heat sinks are attached, an interface material is required, preferably thermal grease and a spring clip.

The spring clip should connect to the printed-circuit board, either to the board itself, to hooks soldered to

the board, or to a plastic stif fener . Avoid attachment forces that can lift the edge of the package or peel the

package from the board. Such peeling forces reduce the solder joint lifetime of the package. The

recommended maximum force on the top of the package is 10 lb force (4.5 kg force). Any adhesive

attachment should attach to painted or plastic surfaces, and its performanc e should be verified under the

application requirements.

20.3.1 Experimental Determination of the Junction Temperature with a

Heat Sink

When a heat sink is used, the junction temperature is determined from a thermocouple inserted at the

interface between the case of the package and the interface material. A clearance slot or hole is normally

required in the heat sink. Minimize the size of the clearance to minimize the change in thermal

performance caused by removing part of the thermal interface to the heat sink. Because of the experimental

dif ficulties with this technique, many engineers measure the heat sink temperature and then back calculate

the case temperature using a separate measurement of the thermal resistance of the interface. From this

case temperatur e, th e junction temper at ure is determine d from the junction-to -c ase ther ma l resis tan ce.

TJ = TC + (R

JC × PD)

where:

TJ = junction temperature (°C)

TC = case temp er ature of the package (°C)

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

72 Freescale Semiconductor

System Design Information

JC = junction-to-case thermal resistance (°C/W)

PD = power dissipation (W)

21 System Design Information

This section provides electrical and thermal design recommendations for successful application of the

MPC8343EA.

21.1 System Clocking

The MPC8343EA includes two PLLs:

1. The platform PLL generates the platform cloc k from the externally supplied CLKIN input. The

frequency ratio between the platform and CLKIN is selected using the platform PLL ratio

configuration bits as described in Section 19.1, “System PLL Configuration.”

2. The e300 core PLL generates the core clock as a slave to the platform clock. The frequency ratio

between the e300 core clock and the platform clock is selected using the e300 PLL ratio

configuration bits as described in Section 19.2, “Core PLL Configuration.”

21.2 PLL Power Supply Filtering

Each PLL gets power through independent power supply pins (AVDD1, AVDD2, respectively). The AVDD

level should always equal to VDD, and preferably these voltages are derived directly from VDD thr ough a

low frequency filter scheme.

There are a number of ways to provide power reliably to the PLLs, but the recommended solution is to

provide four independent filter circuits as illustrated in Figure 37, one to each of the four AVDD pins.

Independent filters to each PLL reduce the opportunity to cause noise injection from one PLL to the other.

The circuit filters noise in the PLL resonant frequency range from 500 kHz to 10 MHz. It should be built

with surface mount capacitors with minimum ef fective series inductance (ESL). Consistent with the

recommendations of Dr. Howard Johnson in High Speed Digital Design: A Handbook of Bl ack Magic

(Prentice Hall, 1993), multiple small capacitors of equal value are recommended over a single large value

capacitor.

T o minimi ze noise coupled from nearby circuits, each circuit should be placed as closely as possible to the

specific AVDD pin being supplied. It shoul d be possible to route directly f rom the capacitors to the AVDD

pin, which is on the periphery of package, without the inductance of vias.

Figure 37 s hows the PLL power supply filter circuit.

Figure 37. PLL Power Supply Filter Circuit

VDD AVDD (or L2AVDD)

2.2 µF 2.2 µF

GND Low ESL Surface Mount Capacitors

10 Ω

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 73

System Design Information

21.3 Decoupling Recommendations

Due to large address and data buses and high operating frequencies, the MPC8343EA can generate

transient power sur ges and high frequency noise in its power supply, especially while driving large

capacitive loads. This noise must be prevented from reaching other components in the MPC8343EA

system, and the MPC8343EA itself requires a clean, tightly regulated source of power. Therefore, the

system designer should place at least one decoupling capacitor at each VDD, OVDD, GVDD, and LVDD pin

of the MPC8343EA. These capacitors should receive their power from separate VDD, OVDD, GV DD,

LVDD, and GND power planes in the PCB, with short traces to minimize inductance. Capacitors can be

placed directly under the device using a standard escape pattern. Others can surround the part.

These capacitors should have a value of 0.01 or 0.1 µF. Only ceramic SMT (surface mount technology)

capacitors should be used to minimize lead inductance, preferably 0402 or 0603 s izes.

In addition, distribute severa l bulk storage capacitors around the PCB, feeding the VDD, OVDD, G VDD,

and LVDD planes, to enable quick rechargi ng of the smaller chip capacitors. These bulk capacitors should

have a low ESR (equivalent serie s resistance) rating to ensure the quick response time. They should also

be connected to the power and ground planes through two vias to minimize inductance. Suggested bulk

capacitors are 100–330 µF (AVX TPS tantalum or Sanyo OSC ON).

21.4 Connection Recommendations

To ensure reliable operation, connect unused inputs to an appropriate signal level. Unused active low

inputs should be tied to OVDD, G V DD, o r LVDD as required. Unused active high inputs should be

connected to GND. All NC (no-connect) signals must remain unconnected.

Power and gr ound connections must be made to all external VDD, GVDD, LVDD, OVDD, and GND pins of

the MPC8343EA.

21.5 Output Buffer DC Impedance

The MPC8 343EA drivers are characterized over process, voltage, and temperature. For all buses, the

driver is a push-pull single-ended driver type (open drain for I2C).

To measure Z0 for the single-ended drivers, an external resistor is connected from the chip pad to OVDD

or GND. Then the value of each resistor is varied until the pad voltage is OVDD/ 2 (s ee Figure 38). The

output impedance is the average of two components, the resistances of the pull-up and pull -down devices.

When data is held high, SW1 is closed (SW2 is open) and RP is trimmed until the voltage at the pad equals

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

74 Freescale Semiconductor

System Design Information

OVDD/2. RP then becomes the resistance of the pull-up devices. RP and RN are designed to be close to each

other in value. Then, Z0 = (RP + RN)/2.

Figure 38. Driver Impedance Measurement

Two measurements give the value of this resistance and the strength of the driv er current source. First, the

output voltage is measured while driving logic 1 without an external differential termination resistor. The

measured voltage is V1 = Rsource × Isource. Second, the output voltage is measured while driving logic 1

with an external precision diff e rential termination resistor of value Rterm. The measured voltage is

V2=(1/(1/R

1+1/R

2)) × Isource. Solving for the output impedance gives Rsource = Rterm × (V1/V2–1). The

drive current is then Isource =V

1/Rsource.

Table 60 summarizes the signal impe dance targets. Th e driver impedance are targeted at minimum VDD,

nominal OVDD, 105°C.

21.6 Configuration Pin Multiplexing

The MPC8343EA power-on configuration options can be set through external pull-up or pull-down

resistors of 4.7 kΩ on certain output pins (see the customer-visible configuration pins). These pins are used

as output only pins in normal operation.

Table 60. Impedance Characteristics

Impedance

Local Bus, Ethernet,

DUART, Control,

Configuration, Power

Management

PCI Signals

(Not Including PCI

Output Clocks)

PCI Output Clocks

(Including

PCI_SYNC_OUT)

DDR DRAM Symbol Unit

RN42 Target 25 Target 42 Target 20 Target Z0W

RP42 Target 25 Target 42 Target 20 Target Z0W

Differential NA NA NA NA ZDIFF W

Note: Nominal supply voltages. See Ta bl e 1 , Tj = 105°C.

OVDD

OGND

Pad

Data

SW1

SW2

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 75

Document Revision History

However , while HRESET is asserted, these pins are treated as inputs, and the value on these pins is latched

when PORESET deasserts. Then the input r eceiver is disabled and the I/O circuit takes on its normal

function. Careful board layout with stubless connections to these pull-up/pull-down resistors coupled with

the large value of the pull-up/pull-down resistor shou ld minimize the disruption of signal qual ity or speed

for the output pins.

21.7 Pull-Up Resistor Requirements

The MPC8343EA requires high resistance pull-up resistors (10 kΩ is recommended) on open-drain pins,

including I2C pins, the Ethernet Management MDIO pin, and IPIC interrupt pins.

For more information on required pull-up resistors and the connections required for the JTAG interface,

refer to application note AN2931, PowerQUIC C™ Design Check list.

22 Document Revision History

Table 61 provides a revision history of this document.

Table 61. Document Revision History

Revision Date Substantive Change(s)

8 5/2009 In Ta b l e 6 2 , footnote 1, changed 667(TBGA) to 533(TBGA). footnote 4, added data rate for DDR1 and

DDR2.

In Ta b le 5 2 , Added two columns for the DDR1 and DDR2 memory bus frequency.

In Section 18.1, “Package Parameters for the MPC8343EA PBGA, changed solder ball for TBGA and

PBGA from 95.5 Sn/0.5 Cu/4 Ag to 96.5 Sn/3.5 Ag.

7 2/2009 In Section 21.1, “System Clocking,” removed “(AVDD1)” and “(AVDD2”) from bulleted list.

In Section 21.2, “PLL Power Supply Filtering,” in the second paragraph, changed “provide five

independent filter circuits,” and “the five AVDD pins” to provide four independent filter circuits,” and “the

four AVDD pins.”

In Ta b le 3 4 , corrected tLBKHOV parametr to tLBKLOV (output data is driven on falling edge of clock in

DLL bypass mode). Similarly, made the same correction to Figure 17, Figure 19, and Figure 20 for

output signals.

In Section 9.2, “USB AC Electrical Specifications,” clarified that AC table is for ULPI only.

In Ta b le 6 2 , updated note 1 to say the following: “For temperature range = C, processor frequency is

limited to 400 with a platform frequency of 266.”

Added footnote 10 to Table 50.

In Ta b le 5 0 , updated note 11 to say the following: “SEC1_TXD[3] is required an external pull-up

resistor. For proper functionality of the device, this pin must be pulled up or actively driven high

during a hard reset. No external pull-down resistors are allowed to be attached to this net.”

Added footnote 6 to Table 7.

In Ta b l e 7 , updated the note 6 to say the following: “The Spread spectrum clocking. Is allowed with 1%

input frequency down-spread at maximum 50KHz modulation rate regardless of input frequency.”

6 4/2007 In Ta b le 3 , “Output Drive Capability,” changed the values in the Output Impedance column and added

USB to the seventh row.

In Section 21.7, “Pull-Up Resistor Requirements,” deleted last two paragraphs and after first

paragraph, added a new paragraph.

Deleted Section 21.8, “JTAG Configuration Signals,” and Figure 43, “JTAG Interface Connection.”

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

76 Freescale Semiconductor

Document Revision History

5 2/2007 Page 1, updated first paragraph to reflect PowerQUICC II information.

In Table 18, “DDR and DDR2 SDRAM Input AC Timing Specifications,” added note 2 to tCISKEW and

deleted original note 3; renumbered the remaining notes.

In Figure 38, “JTAG Interface Connection,” updated with new figure.

In Section 23, “Ordering Information,” replaced first paragraph and added a note.

In Section 23.1, “Part Numbers Fully Addressed by This Document,” replaced first paragraph.

Updated back page information.

4 12/2006 Table 19, “DDR and DDR2 SDRAM Output AC Timing Specifications,” modified Tddkhds for 333 MHz

from 900 ps to 775 ps.

3 11/2006 Updated note in introduction.

In the features list in Section 1, “Overview,” corrected DDR data rate to show 266 MHz for PBGA parts

for all silicon revisions.

In Table 57, “Suggested PLL Configurations,” added the following row:

Ref No: 823, SPMF: 1000, Core PLL: 0100011, 400-MHz Device Input Clock Freq: 33, CSB

Freq: 266, and Core Freq: 400.

In Section 23, “Ordering Information,” replicated note from document introduction.

2 8/2006 Changed number of general purpose parallel I/O pins to 39 in Section 1, “Overview.”

Changed all references to revision 2.0 silicon to revision 3.0 silicon.

Changed VIH minimum value in Table 35, “JTAG Interface DC Electrical Characteristics,” to

OVDD –0.3.

In Table 44, “PCI DC Electrical Characteristics,” changed high-level input voltage values to min = 2 and

max = OVDD + 0.3; changed low-level input voltage values to min = (–0.3) and max = 0.8.

In Table 40, “PCI DC Electrical Characteristics,” changed high-level input voltage values to min = 2 and

max = OVDD + 0.3; changed low-level input voltage values to min = (–0.3) and max = 0.8.

In Table 44, “PCI DC Electrical Characteristics,” changed high-level input voltage values to min = 2 and

max = OVDD + 0.3; changed low-level input voltage values to min = (–0.3) and max = 0.8.

Updated DDR2 I/O power values in Table 5, “MPC8343EA Typical I/O Power Dissipation.”

1 4/2006 Removed Table 20, “Timing Parameters for DDR2-400.”

Changed ADDR/CMD to ADDR/CMD/MODT in Table 9, “DDR and DDR2 SDRAM Output AC Timing

Specifications,” rows 2 and 3, and in Figure 2, “DDR SDRAM Output Timing Diagram.

Changed Min and Max values for VIH and VIL in Table 44,“PCI DC Electrical Characteristics.”

In Table 58, “MPC8343EA (PBGA) Pinout Listing,” modified rows for MDICO and MDIC1 signals and

added note ‘It is recommended that MDICO be tied to GRD using an 18 Ω resistor and MCIC1 be tied

to DDR power using an 18 Ω resistor.’

In Table 58, “MPC8343EA (PBGA) Pinout Listing,” in row AVDD3 changed power supply from ‘AVDD3’

to ‘—.’

0 3/2006 Initial release.

Table 61. Document Revision History (continued)

Revision Date Substantive Change(s)

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 77

Ordering Information

23 Ordering Information

This section presents ordering information for the device discussed in this document, and it shows an

example of how the parts are marked.

NOTE

The information in this document is acc urate for revision 3.x silicon and

later (in other words, for orderable part numbers ending in A or B). For

information on revision 1.1 silicon and earlier versions, see the MPC8343E

PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications

(Document Order No. MPC8343EEC).

23.1 Part Numbers Fully Addressed by This Document

Table 62 shows an analysis of the Freescale part numbering nomenclature for the MPC8343EA. The

individual part numbers correspond to a maximum processor core frequency. Each part number also

contains a revision code that refers to the die mask revision number . For available frequency configuration

parts including extended temperatures, refer to the MPC8343EA product summary page on our website

listed on the back cover of this document or, contact your local Freescale sales office.

Table 63 shows the SVR settings by device and package type.

Table 62. Part Numbering Nomenclature

MPC nnnn e t pp aa a r

Product

Code

Part

Identifier

Encryption

Acceleration

Temperature1

Range Package2Processor

Frequency3

Platform

Frequency

Revision

Level

MPC 8343 Blank = Not

included

E = included

Blank = 0 to 105°C

C = –40 to 105°CZQ = PBGA

VR = PB Free PBGA

e300 core

speed

AD = 266

AG = 400

D = 266 B = 3.1

Notes:

1. For temperature range = C, processor frequency is limited to 400 with a platform frequency of 266 and up to with a platform

frequency of 333

2. See Section 18, “Package and Pin Listings,” for more information on available package types.

3. Processor core frequencies supported by parts addressed by this specification only. Not all parts described in this

specification support all core frequencies. Additionally, parts addressed by Part Number Specifications may support other

maximum core frequencies.

Table 63. SVR Settings

Device Package SVR (Rev. 3.0)

MPC8343EA PBGA 8056_0030

MPC8343A PBGA 8057_0030

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

78 Freescale Semiconductor

Ordering Information

23.2 Part Marking

Parts are marked as in the example shown in Figure 39.

Figure 39. Freescale Part Marking for PBGA Devices

MPCnnnnetppaaar

core/platform MHZ

ATWLYYWW

CCCCC

PBGA

*MMMMM YWWLAZ

Notes:

ATWLYYWW is the traceability code.

CCCCC is the country code.

MMMMM is the mask number.

YWWLAZ is the assembly traceability code.

MPC8343EA PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications, Rev. 8

Freescale Semiconductor 79

Ordering Information

THIS PAGE INTENTIONALLY LEFT BLANK

Document Number: MPC8343EAEC

Rev. 8

05/2009

Information in this document is provided solely to enable system and software

implementers to use Freescale Semiconductor products. There are no express or

implied copyright licenses granted hereunder to design or fabricate any integrated

circuits or integrated circuits based on the information in this document.

Freescale Semiconductor reserves the right to make changes without further notice to

any products herein. Freescale Semiconductor makes no warranty, representation or

guarantee regarding the suitability of its products for any particular purpose, nor does

Freescale Semiconductor assume any liability arising out of the application or use of

any product or circuit, and specifically disclaims any and all liability, including without

limitation consequential or incidental damages. “Typical” parameters which may be

provided in Freescale Semiconductor data sheets and/or specifications can and do

vary in different applications and actual performance may vary over time. All operating

parameters, including “Typicals” must be validated for each customer application by

customer’s technical experts. Freescale Semiconductor does not convey any license

under its patent rights nor the rights of others. Freescale Semiconductor products are

not designed, intended, or authorized for use as components in systems intended for

surgical implant into the body, or other applications intended to support or sustain life,

or for any other application in which the failure of the Freescale Semiconductor product

could create a situation where personal injury or death may occur. Should Buyer

purchase or use Freescale Semiconductor products for any such unintended or

unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor

and its officers, employees, subsidiaries, affiliates, and distributors harmless against all

claims, costs, damages, and expenses, and reasonable attorney fees arising out of,

directly or indirectly, any claim of personal injury or death associated with such

unintended or unauthorized use, even if such claim alleges that Freescale

Semiconductor was negligent regarding the design or manufacture of the part.

How to Reach Us:

Home Page:

www.freescale.com

Web Support:

http://www.freescale.com/support

USA/Europe or Locations Not Listed:

Freescale Semiconductor, Inc.

Technical Information Center, EL516

2100 East Elliot Road

Tempe, Arizona 85284

1-800-521-6274 or

+1-480-768-2130

www.freescale.com/support

Europe, Middle East, and Africa:

Freescale Halbleiter Deutschland GmbH

Technical Information Center

Schatzbogen 7

81829 Muenchen, Germany

+44 1296 380 456 (English)

+46 8 52200080 (English)

+49 89 92103 559 (German)

+33 1 69 35 48 48 (French)

www.freescale.com/support

Japan:

Freescale Semiconductor Japan Ltd.

Headquarters

ARCO Tower 15F

1-8-1, Shimo-Meguro, Meguro-ku

Tokyo 153-0064

Japan

0120 191014 or

+81 3 5437 9125

support.japan@freescale.com

Asia/Pacific:

Freescale Semiconductor China Ltd.

Exchange Building 23F

No. 118 Jianguo Road

Chaoyang District

Beijing 100022

China

+86 10 5879 8000

support.asia@freescale.com

For Literature Requests Only:

Freescale Semiconductor

Literature Distribution Center

P.O. Box 5405

Denver, Colorado 80217

1-800 441-2447 or

+1-303-675-2140

Fax: +1-303-675-2150

LDCForFreescaleSemiconductor

@hibbertgroup.com

Freescale, the Freescale logo, and StarCore are trademarks or registered

trademarks of Freescale Semiconductor, Inc. in the U.S. and other

countries. All other product or service names are the property of their

respective owners. The Power Architecture and Power.org word marks and

the Power and Power.org logos and related marks are trademarks and

service marks licensed by Power.org. IEEE 802.3, 802.3u, 820.3x, 802.3z,

802.3ac, 802.11i, and 1149.1 are trademarks and registered trademarks of

the Institute of Electrical and Electronics Engineers, Inc. (IEEE). This

product is not endorsed or approved by the IEEE.