The following document contains information on Cypress products. S6SAP412A Programable Evaluation board for Multi-phase 2ch Buck + 1ch Buck/Boost DC/DC with I2C Interface Operation Manual Publication Number S6SAP412A_SS901-00025 Revision 2.0 Issue Date July 22, 2014 O p e r a t i o n M a n u a l PREFACE This manual explains how to use the evaluation board. Be sure to read this manual before using the product. For this product, please consult with sales representatives or support representatives. Handling and use Handling and use of this product and notes regarding its safe use are described in the manuals. Follow the instructions in the manuals to use this product. Keep this manual at hand so that you can refer to it anytime during use of this product. Notice on this document All information included in this document is current as of the date it is issued. Such information is subject to change without any prior notice. Please confirm the latest relevant information with the sales representatives. 2 CONFIDENTIAL S6SAP412A_SS901-00025-2v0-E, July 22, 2014 O p e r a t i o n M a n u a l Caution of the products described in this document The following precautions apply to the product described in this manual. WARNING Indicates a potentially hazardous situation which could result in death or serious injury and/or a fault in the user's system if the product is not used correctly. Electric shock, Damage Before performing any operation described in this manual, turn off all the power supplies to the system. Performing such an operation with the power on may cause an electric shock or device fault. Electric shock, Damage CAUTION Once the product has been turned on, do not touch any metal part of it. Doing so may cause an electric shock or device fault. Indicates the presence of a hazard that may cause a minor or moderate injury, damages to this product or devices connected to it, or may cause to loose software resources and other properties such as data, if the device is not used appropriately. Before moving the product, be sure to turn off all the power supplies and unplug the cables. Watch your Cuts, Damage step when carrying the product. Do not use the product in an unstable location such as a place exposed to strong vibration or a sloping surface. Doing so may cause the product to fall, resulting in an injury or fault. Cuts Damage The product contains sharp edges that are left unavoidably exposed, such as jumper plugs. Handle the product with due care not to get injured with such pointed parts. Do not place anything on the product or expose the product to physical shocks. Do not carry the product after the power has been turned on. Doing so may cause a malfunction due to overloading or shock. Damage Damage Since the product contains many electronic components, keep it away from direct sunlight, high temperature, and high humidity to prevent condensation. Do not use or store the product where it is exposed to much dust or a strong magnetic or electric field for an extended period of time. Inappropriate operating or storage environments may cause a fault. Use the product within the ranges given in the specifications. Operation over the specified ranges may cause a fault. To prevent electrostatic breakdown, do not let your finger or other object come into contact with the Damage metal parts of any of the connectors. Before handling the product, touch a metal object (such as a door knob) to discharge any static electricity from your body. Damage When turning the power on or off, follow the relevant procedure as described in this document. Before turning the power on, in particular, be sure to finish making all the required connections. Furthermore, be sure to configure and use the product by following the instructions given in this document. Using the product incorrectly or inappropriately may cause a fault. Because the product has no casing, it is recommended that it be stored in the original packaging. Damage Transporting the product may cause a damage or fault. Therefore, keep the packaging materials and use them when re-shipping the product. S6AP412A_SS901-00025-2v0-E, July 22, 2014 CONFIDENTIAL 3 O p e r a t i o n M a n u a l Table of Contents 1. 2. 3. Description ..................................................................................................................................... 5 Evaluation board specification ........................................................................................................ 5 PIN descriptions ............................................................................................................................. 6 3.1 Input/output pin descriptions ............................................................................................... 6 3.2 Jumper, Switch descriptions ................................................................................................ 6 4. Setup and verification ..................................................................................................................... 7 5. Component and wiring layout ......................................................................................................... 8 5.1 Component layout ............................................................................................................... 8 5.2 Wiring layout ....................................................................................................................... 9 6. Circuit schematic .......................................................................................................................... 11 7. Component list.............................................................................................................................. 12 8. Evaluation board picture ............................................................................................................... 13 9. Ordering Information..................................................................................................................... 14 10. Major Changes ............................................................................................................................. 15 Figures Figure1-1 Board outline .............................................................................................................................. 5 Figure4-1 For Control switch evaluation ..................................................................................................... 7 Figure5-1 Component layout (layer 1) ........................................................................................................ 8 Figure5-2 Component layout (layer 4) ........................................................................................................ 8 Figure5-3 Wiring layout (layer 1) ................................................................................................................ 9 Figure5-4 Wiring layout (layer 2) ................................................................................................................ 9 Figure5-5 Wiring layout (layer 3) .............................................................................................................. 10 Figure5-6 Wiring layout (layer 4) .............................................................................................................. 10 Figure6-1 Circuit schematic for power block ............................................................................................. 11 Figure8-1 Picture (top) ............................................................................................................................. 13 Figure8-2 Picture (back) ........................................................................................................................... 13 Tables Table2-1 Evaluation board specification ..................................................................................................... 5 Table3-1 Input/output pin descriptions ........................................................................................................ 6 Table3-2 Jumper, Switch Descriptions........................................................................................................ 6 Table7-1 Component list........................................................................................................................... 12 Table9-1 Ordering Information .................................................................................................................. 14 4 CONFIDENTIAL S6SAP412A_SS901-00025-2v0-E, July 22, 2014 S6SAP412A Programable Evaluation board for Multi-phase 2ch Buck + 1ch Buck/Boost DC/DC with I2C Interface Operation Manual 1. Description The S6SAP412A is the evaluation board for 2ch Buck + 1ch Buck/Boost DC/DC, S6AP412A. This board implements S6AP412A : Option-code 78, and output preset voltage DD1:1.0V, DD2:1.8V, DD2:3.3V. Also, this board implements the I2C interface. The separated communication tool is sold, and it can select the output voltage, soft-start time, ON/OFF sequence, PFM/PWM mode easily with I2C communication using windows PC and prepared software. Figure1-1 Board outline 2. Evaluation board specification Table2-1 Evaluation board specification Symbol Min Typ MAx Unit Input voltage Item VIN 2.5 3.3 5.5 V Output voltage Vo1 0.988 1.00 1.012 V mA Output current Io1 - - 4000 Output voltage Vo2 1.778 1.80 1.822 V Output current Io2 - - 1200 mA Output voltage Vo3 3.23 3.30 3.37 V Output current Io3 - - 600 mA Board size:28mm x 28mm S6SAP412A_SS901-00025-2v0-E, July 22, 2014 CONFIDENTIAL 5 O p e r a t i o n M a n u a l 3. PIN descriptions 3.1 Input/output pin descriptions Table3-1 Input/output pin descriptions Block DD1 DD2 DD3 CTL MODE I2C COMMON 3.2 Pin symbol I/O Function description Vo1 O DD1 output terminal PG1 Vo2 O DD1 POWERGOOD output monitor terminal DD2 output terminal PG2 Vo3 O PG3 CTL1 O CTL2 CTL3 I CTLM MODE I DVCC SCL I SDA ADDS I/O O O I DD3 POWERGOOD output monitor terminal DD1 control terminal DD2 control terminal DD3 control terminal I Control terminal for common block and logic block MODE signal output terminal I Power supply terminal for I2C. I2C clock terminal I I DD2 POWERGOOD output monitor terminal DD3 output terminal I2C data I/O terminal Select terminal for slave address VIN GND I - Control circuit block power supply terminal Control circuit block ground terminal GND3 - Control circuit block ground terminal Jumper, Switch descriptions Table3-2 Jumper, Switch Descriptions Jumper, Switch 6 CONFIDENTIAL Description JP1 Short VIN terminal and VBUS pin (2 pin) CN1 1,8,12,14,17 : GND pin 2 : VIN pin 4 : DVCC pin 5 : SCL pin 6 : SDA pin 3,7,9,10,11,13,15,16,18,19,20 : open Initial setting Open - S6SAP412A_SS901-00025-2v0-E, July 22, 2014 O p e r a t i o n M a n u a l 4. Setup and verification S6AP412A preset value can be evaluated with stabilized power supply. 1. 3.3V is applied to VIN terminal. 2. CTLM, CTL1, CTL2, CTL3 switch are tern on 3. Vo1:1.0V, Vo2:1.8V, Vo3:3.3V is output. Figure4-1 For Control switch evaluation S6SAP412A_SS901-00025-2v0-E, July 22, 2014 CONFIDENTIAL 7 O p e r a t i o n M a n u a l 5. Component and wiring layout 5.1 Component layout Figure5-1 Component layout (layer 1) Figure5-2 Component layout (layer 4) 8 CONFIDENTIAL S6SAP412A_SS901-00025-2v0-E, July 22, 2014 O p e r a t i o n 5.2 M a n u a l Wiring layout Figure5-3 Wiring layout (layer 1) Figure5-4 Wiring layout (layer 2) S6SAP412A_SS901-00025-2v0-E, July 22, 2014 CONFIDENTIAL 9 O p e r a t i o n M a n u a l Figure5-5 Wiring layout (layer 3) Figure5-6 Wiring layout (layer 4) 10 CONFIDENTIAL S6SAP412A_SS901-00025-2v0-E, July 22, 2014 O p e r a t i o n M a n u a l 6. Circuit schematic Figure6-1 Circuit schematic for power block VIN M1 Vi1 Vi2 GND1 GND2 GND3 23 LX1A/LX1 PGND1A/PGND1 PG1 L1 22 1mH 21 R5 VIN 28 PG1 17 ADDSEL/IN4 PVCC1B/PVCC4 L4 1mH Vo1 19 C2 LX1B/LX4 18 C11 ADDS 4.7mF 100k 47mF PVCC1A/PVCC1 C1 IN1 4.7mF VIN 24 PGND1B/PGND4 20 5 PGND2 PG2 MB39C032_033 6 Vo2 L2 1mH C5 LX2 22mF PVCC2 C4 IN2 4.7mF VIN 8 7 VIN R6 29 100k PG2 PVCC3 4 C7 IN3/PG4 LX3_1 4.7mF VIN 31 3 L3 1mH Vo3 C8 32 SCL C15 SCL SDA SDA 16 0.1mF R8 DVCC R9 DVCC 14 15 DVCC LX3_2 SCL PGND3 SDA PG3 VIN JP1 33mF VO3 1 2 3 1 2 DVCC 4 SCL 5 SDA 6 7 R7 30 VIN 8 9 100k 10 CTL3 11 11 12 AVCC CTL3 CTLMAIN 27 13 14 15 10k CTL2 R1 VIN R4 10 CTL1 0.1mF CTL2 9 C14 CTL1 PG3 CTLM 25 16 17 18 S6SAP412A_SS901-00025-2v0-E, July 22, 2014 CONFIDENTIAL 19 C16 26 1mF VREF18 GND MODE/CTL4 20 VBUS USBVCC I2CVCC SCL SDA P10 GND2 P11 GND3 P12 GND4 P13 GND5 P14 P15 GND6 P21 P22 P23 CN1 13 12 33 EP MODE GND1 11 O p e r a t i o n M a n u a l 7. Component list Table7-1 Component list No. Component 1 M1 PMIC Item S6AP412A-78 Parts number SPANSION Vendor Value Remarks - - 2 L1 Inductor 1276AS-H-1R0M 3 L2 Inductor 1276AS-H-1R0M TOKO 1.0H - TOKO 1.0H - 4 L3 Inductor 5 L4 Inductor 1276AS-H-1R0M TOKO 1.0H - 1276AS-H-1R0M TOKO 1.0H - 6 C14 7 C15 Ceramic Capacitor C1005JB1H104K050BB TDK 0.1F 50V Ceramic Capacitor C1005JB1H104K050BB TDK 0.1F 50V 8 9 C16 Ceramic Capacitor C1608X5R1H105K080AB TDK 1F 50V C1 Ceramic Capacitor C1608X5R1V475K080AC TDK 4.7F 35V 10 C4 Ceramic Capacitor C1608X5R1V475K080AC TDK 4.7F 35V 11 C7 Ceramic Capacitor C1608X5R1V475K080AC TDK 4.7F 35V 12 C11 Ceramic Capacitor C1608X5R1V475K080AC TDK 4.7F 35V 13 C5 Ceramic Capacitor C2012X5R1A226K125AB TDK 22F 10V 14 C8 Ceramic Capacitor C2012X5R1A336M125AC TDK 33F 10V 15 C2 Ceramic Capacitor C2012X5R1A476M125AC TDK 47F 10V 16 R1 Chip Resistor RK73Z1E KOA 0 Under 50mV 17 R4 Chip Resistor RR0816P103D SUSUMU 10k 0.5%, 25ppm/C 18 R5 Chip Resistor RR0510P-104-D SUSUMU 100k 0.5%, 25ppm/C 19 R6 Chip Resistor RR0510P-104-D SUSUMU 100k 0.5%, 25ppm/C 20 R7 Chip Resistor RR0510P-104-D SUSUMU 100k 0.5%, 25ppm/C 21 R8 Chip Resistor RR0510P-222-D SUSUMU 2.2k 0.5%, 25ppm/C 22 R9 Chip Resistor RR0510P-222-D SUSUMU 2.2k 0.5%, 25ppm/C Neltron Industrial CN1 Connector 2214R-20SG-85-F1 24 Vi1/Vi2 Terminal HIF3H-20PB-2.54DSA HIROSE - - 25 GND1/GND2 Terminal HIF3H-20PB-2.54DSA HIROSE - - 26 GND3 Terminal HIF3H-20PB-2.54DSA HIROSE - - 27 DVCC Terminal HIF3H-20PB-2.54DSA HIROSE - - 28 SCL Terminal HIF3H-20PB-2.54DSA HIROSE - - 29 SDA Terminal HIF3H-20PB-2.54DSA HIROSE - - 30 ADDS Terminal HIF3H-20PB-2.54DSA HIROSE - - 31 CTLM Terminal HIF3H-20PB-2.54DSA HIROSE - - 32 CTL1 Terminal HIF3H-20PB-2.54DSA HIROSE - - 33 CTL2 Terminal HIF3H-20PB-2.54DSA HIROSE - - 34 CTL3 Terminal HIF3H-20PB-2.54DSA HIROSE - - 35 MODE Terminal HIF3H-20PB-2.54DSA HIROSE - - 36 Vo1 Terminal HIF3H-20PB-2.54DSA HIROSE - - 37 PG1 Terminal HIF3H-20PB-2.54DSA HIROSE - - 38 Vo2 Terminal HIF3H-20PB-2.54DSA HIROSE - - 39 PG2 Terminal HIF3H-20PB-2.54DSA HIROSE - - 40 Vo3 Terminal HIF3H-20PB-2.54DSA HIROSE - - 41 PG3 Terminal HIF3H-20PB-2.54DSA HIROSE JP1 Solder jumper Solder jumper 42 Co., Ltd. - 1x20pin header (2.54pitch) 23 Unmounted - - Unmounted These components are compliant with RoHS, and please ask each vendor for details if necessary. 12 CONFIDENTIAL S6SAP412A_SS901-00025-2v0-E, July 22, 2014 O p e r a t i o n M a n u a l 8. Evaluation board picture Figure8-1 Picture (top) Figure8-2 Picture (back) S6SAP412A_SS901-00025-2v0-E, July 22, 2014 CONFIDENTIAL 13 O p e r a t i o n M a n u a l 9. Ordering Information Table9-1 Ordering Information 14 CONFIDENTIAL Part number EVB revision Note S6SAP412A78SA1001 Rev 1.0 --- S6SAP412A_SS901-00025-2v0-E, July 22, 2014 O p e r a t i o n M a n u a l 10. Major Changes Page Section Change Results Revision 1.0 - - Initial release Revision 2.0 Revised the Component of Component list 12 7. Component list Vi Vi1/Vi2 GND GND1/GND2 14 9. Ordering Information S6SAP412A_SS901-00025-2v0-E, July 22, 2014 CONFIDENTIAL Revised the Part number of Ordering Information S6SPA412A78SA1001 S6SAP412A78SA1001 15 O p e r a t i o n M a n u a l SS901-00025-2v0-E Spansion Support Tool Manual S6SAP412A Programable Evaluation board for Multi-phase 2ch Buck + 1ch Buck/Boost 2 DC/DC with I C Interface Operation Manual July 2014 Rev. 2.0 Published: Spansion Inc. Edited: Communications 16 CONFIDENTIAL S6SAP412A_SS901-00025-2v0-E, July 22, 2014 O p e r a t i o n M a n u a l Colophon The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for any use that includes fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for any use where chance of failure is intolerable (i.e., submersible repeater and artificial satellite). Please note that Spansion will not be liable to you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the US Export Administration Regulations or the applicable laws of any other country, the prior authorization by the respective government entity will be required for export of those products. Trademarks and Notice The contents of this document are subject to change without notice. This document may contain information on a Spansion product under development by Spansion. Spansion reserves the right to change or discontinue work on any product without notice. The information in this document is provided as is without warranty or guarantee of any kind as to its accuracy, completeness, operability, fitness for particular purpose, merchantability, non-infringement of third-party rights, or any other warranty, express, implied, or statutory. Spansion assumes no liability for any damages of any kind arising out of the use of the information in this document. Copyright (c) 2014 Spansion All rights reserved. Spansion(R), the Spansion logo, MirrorBit(R), MirrorBit(R) EclipseTM, ORNANDTM and combinations thereof, are trademarks and registered trademarks of Spansion LLC in the United States and other countries. Other names used are for informational purposes only and may be trademarks of their respective owners. S6SAP412A_SS901-00025-2v0-E, July 22, 2014 CONFIDENTIAL 17 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Spansion Inc.: S6SAP412A78SA1001