Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers will need to change in order to meet ON Semiconductor's system requirements. Since the ON Semiconductor product management systems do not have the ability to manage part nomenclature that utilizes an underscore (_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please email any questions regarding the system integration to Fairchild_questions@onsemi.com. ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. FNB51060TD1 Motion SPM(R) 55 Series Features General Description * UL Certified No. E209204 (UL1557) FNB51060TD1 is a Motion SPM 55 module providing a fully-featured, high-performance inverter output stage for AC Induction, BLDC, and PMSM motors. These modules integrate optimized gate drive of the built-in IGBTs to minimize EMI and losses, while also providing multiple on-module protection features including under-voltage lockouts, inter-lock function, over-current shutdown, thermal monitoring of drive IC, and fault reporting. The built-in, high-speed HVIC requires only a single supply voltage and translates the incoming logic-level gate inputs to the high-voltage, high-current drive signals required to properly drive the module's robust shortcircuit-rated IGBTs. Separate negative IGBT terminals are available for each phase to support the widest variety of control algorithms. * 600 V - 10 A 3-Phase IGBT Inverter Including Control IC for Gate Drive and Protections * Low-Loss, Short-Circuit Rated IGBTs * Built-In Bootstrap Diodes in HVIC * Separate Open-Emitter Pins from Low-Side IGBTs for Three-Phase Current Sensing * Active-HIGH interface, works with 3.3 / 5 V Logic, Schmitt-trigger Input * HVIC for Gate Driving, Under-Voltage and Short-Circuit Current Protection * Fault Output for Under-Voltage and Short-Circuit Current Protection * Inter-Lock Function to Prevent Short-Circuit * Shut-Down Input * HVIC Temperature-Sensing Built-In for Temperature Monitoring * Optimized for 15 - 20 kHz Switching Frequency * Isolation Rating: 1500 Vrms / min. Applications * Motion Control - Home Appliance / Industrial Motor Related Resources * AN-9096 - Smart Power Module, Motion SPM(R) 55 Series User's Guide * AN-9097 - SPM(R) 55 Packing Mounting Guidance Figure 1. 3D Package Drawing (Click to Activate 3D Content) Package Marking and Ordering Information Device Device Marking Package Packing Type Quantity FNB51060TD1 FNB51060TD1 SPMFA-A20 RAIL 13 (c)2015 Semiconductor FNB51060TD1 Rev. 1.1 1 www.fairchildsemi.com www.onsemi.com FNB51060TD1 Motion SPM(R) 55 Series April 2017 FNB51060TD1 Motion SPM(R) 55 Series Integrated Power Functions * 600 V - 10 A IGBT inverter for three phase DC / AC power conversion (Please refer to Figure 3) Integrated Drive, Protection and System Control Functions * For inverter high-side IGBTs: gate drive circuit, high-voltage isolated high-speed level shifting control circuit Under-Voltage Lock-Out (UVLO) protection * For inverter low-side IGBTs: gate drive circuit, Short-Circuit Protection (SCP) control supply circuit Under-Voltage Lock-Out (UVLO) protection * Fault signaling: corresponding to UVLO (low-side supply) and SC faults * Input interface: High-active interface, works with 3.3 / 5 V logic, Schmitt trigger input * Built in Bootstrap circuitry in HVIC Pin Configuration Figure 2. Top View (c)2015 Semiconductor FNB51060TD1 Rev. 1.1 2 www.fairchildsemi.com www.onsemi.com FNB51060TD1 Motion SPM(R) 55 Series Pin Descriptions Pin Number Pin Name Pin Description 1 P 2 U, VS(U) Output for U Phase 3 V, VS(V) Output for V Phase 4 W, VS(W) Output for W Phase 5 NU Negative DC-Link Input for U Phase 6 NV Negative DC-Link Input for V Phase 7 NW Negative DC-Link Input for W Phase Positive DC-Link Input 8 IN(UL) Signal Input for Low-Side U Phase 9 IN(UH) Signal Input for High- ide U Phase 10 IN(VL) Signal Input for Low-Side V Phase 11 IN(VH) Signal Input for High-Side V Phase 12 IN(WL) Signal Input for Low-Side W Phase 13 IN(WH) Signal Input for High-Side W Phase 14 VDD Common Bias Voltage for IC and IGBTs Driving 15 COM Common Supply Ground Capacitor (Low-Pass Filter) for Short-circuit Current Detection Input 16 CSC 17 VF Fault Output, Shut-Down Input, Temperature Output of Drive IC 18 VB(W) High-Side Bias Voltage for W-Phase IGBT Driving 19 VB(V) High-Side Bias Voltage for V-Phase IGBT Driving 20 VB(U) High-Side Bias Voltage for U-Phase IGBT Driving (c)2015 Semiconductor FNB51060TD1 Rev. 1.1 3 www.fairchildsemi.com www.onsemi.com FNB51060TD1 Motion SPM(R) 55 Series Internal Equivalent Circuit and Input/Output Pins P V B(U) IN(UH) IN(UL) VB HIN LIN HO VS U,Vs (U) LO Nu V B(V) IN(VH) IN(VL) VB HIN LIN HO VS V,Vs(V) LO V B(W) IN(WH) IN(WL) Nv VB HIN LIN HO VF Csc V DD COM VF Csc VDD COM VS U,Vs(W) LO Nw Figure 3. Internal Block Diagram Note: 1. Inverter high-side is composed of three IGBTs, freewheeling diodes, and one control IC for each IGBT. 2. Inverter low-side is composed of three IGBTs, freewheeling diodes, and one control IC for each IGBT. It has gate drive and protection functions. 3. Single drive IC has gate driver for six IGBTs and protection functions. 4. Inverter power side is composed of four inverter DC-link input terminals and three inverter output terminals. (c)2015 Semiconductor FNB51060TD1 Rev. 1.1 4 www.fairchildsemi.com www.onsemi.com unless otherwise specified.) Inverter Part Symbol VPN VPN(Surge) Parameter Conditions Supply Voltage Applied between P - NU, NV, NW Supply Voltage (Surge) Applied between P - NU, NV, NW Rating Unit 450 V 500 V 600 V VCES Collector - Emitter Voltage * IC Each IGBT Collector Current TC = 25C, TJ 150C 10 A * ICP Each IGBT Collector Current (Peak) TC = 25C, TJ 150C, Under 1 ms Pulse Width 20 A Collector Dissipation TC = 25C per Chip 21 W Operating Junction Temperature (Note 5) -40 ~ 150 C Rating Unit * PC TJ Note: 5. The maximum junction temperature rating of the power chips integrated within the Motion SPM(R) 55 product is 150C. Control Part Symbol Parameter Conditions VDD Control Supply Voltage Applied between VDD - COM 20 V VBS High-Side Control Bias Voltage Applied between VB(U) - VS(U), VB(V) - VS(V), VB(W) - VS(W) 20 V VIN Input Signal Voltage Applied between IN(UH), IN(VH), IN(WH), IN(UL), IN(VL), IN(WL) - COM -0.3 ~ VDD +0.3 V VF Fault Supply Voltage Applied between VF - COM -0.3 ~ VDD +0.3 V * IF Fault Current Sink Current at VF pin VSC Current Sensing Input Voltage Applied between CSC - COM 5 mA -0.3 ~ VDD +0.3 V Rating Unit 400 V Total System Symbol VPN(PROT) Parameter Self Protection Supply Voltage Limit (Short Circuit Protection Capability) TSTG Storage Temperature VISO Isolation Voltage Connect Pins to Heat Sink Plate Conditions VDD = VBS = 13.5 ~ 16.5 V TJ = 150C, Non-Repetitive, < 2 s -40 ~ 125 C 1500 Vrms Typ. Max. Unit AC 60 Hz, Sinusoidal, 1 Minute Thermal Resistance Symbol Rth(j-c)Q Rth(j-c)F Parameter Junction to Case Thermal Resistance (Note 7) Conditions Min. Inverter IGBT part (per 1 / 6 module) - - 5.9 C / W Inverter FWD part (per 1 / 6 module) - - 7.6 C / W Note: 6. For Marking " * ", These Value had been made an acquisition by the calculation considered to design factor. 7. For the measurement point of case temperature (TC), please refer to Figure 2. (c)2015 Semiconductor FNB51060TD1 Rev. 1.1 5 www.fairchildsemi.com www.onsemi.com FNB51060TD1 Motion SPM(R) 55 Series Absolute Maximum Ratings (TJ = 25C, unless otherwise specified.) Inverter Part Symbol VCE(SAT) VF HS tON Parameter Conditions Min. Typ. Max. Unit Collector - Emitter Saturation VDD = VBS = 15 V Voltage VIN = 5 V IC = 8 A TJ = 25C - 1.9 2.15 V TJ = 150C - 2.2 - V FWDi Forward Voltage TJ = 25C - 2.2 2.55 V TJ = 150C - 2.0 - V 0.34 0.64 0.94 us - 0.16 0.40 us - 0.38 0.58 us - 0.06 0.10 us VIN = 0 V IF = 8 A Switching Times VPN = 400 V, VDD = VBS = 15 V, IC = 10A TJ = 25C VIN = 0 V 5 V, Inductive load (Note 8) tC(ON) tOFF tC(OFF) - 0.06 - us 0.34 0.64 0.94 us - 0.16 0.40 us - 0.38 0.58 us tC(OFF) - 0.06 0.10 us trr - 0.06 - us - - 1 mA trr LS VPN = 400 V, VDD = VBS = 15 V, IC = 10A TJ = 25C VIN = 0 V 5 V, Inductive load (Note 8) tON tC(ON) tOFF Collector - Emitter Leakage VCE = VCES Current ICES Note: 8. tON and tOFF include the propagation delay of the internal drive IC. tC(ON) and tC(OFF) are the switching time of IGBT itself under the given gate driving condition internally. For the detailed information, please see Figure 4. 100% I C 100% I C t rr V CE IC IC V IN V IN t ON t OFF t C(ON) t C(OFF) 10% I C V IN(ON) V CE 90% I C V IN(OFF) 10% V CE 10% V CE 10% I C (b) turn-off (a) turn-on Figure 4. Switching Time Definition (c)2015 Semiconductor FNB51060TD1 Rev. 1.1 6 www.fairchildsemi.com www.onsemi.com FNB51060TD1 Motion SPM(R) 55 Series Electrical Characteristics (TJ = 25C, Symbol Parameter Conditions Min. Typ. Max. Unit IQDD Quiescent VDD Supply Current VDD = 15 V, IN(UH,VH,WH,UL,VL,WL) = 0 V VDD - COM - 1.5 2.0 mA IPDD Operating VDD Supply Current VDD = 15 V, fPWM = 20 kHz, duty = VDD - COM 50%, applied to one PWM signal input - 1.8 2.5 mA IQBS Quiescent VBS Supply Current VBS = 15 V, IN(UH, VH, WH) = 0 V VB(U) - VS(U), VB(V) VS(V), VB(W) - VS(W) - 30 60 A IPBS Operating VBS Supply Current VDD = VBS = 15 V, fPWM = 20 kHz, VB(U) - VS(U), VB(V) duty = 50%, applied to one PWM VS(V), VB(W) - VS(W) signal input for high - side - 330 450 A VFH Fault Output Voltage VSC = 0 V, VF Circuit: 10 k to 5 V Pull-up 4.5 - - V VSC = 1 V, VF Circuit: 10 k to 5 V Pull-up VFL VSC(ref) Short-Circuit Trip Level VDD = 15 V (Note 4) UVDDD UVDDR UVBSD Supply Circuit Under-Voltage Protection UVBSR 11.4 12.1 V 12.3 13.0 V Detection level 10.1 10.8 11.5 V Reset level 10.7 11.4 12.1 V 68 81 95 A 4.05 4.19 4.32 V 40 120 - s - - 2.4 V 0.8 - - V - - 2.4 V 0.8 - - V HVIC Temperature Sensing Voltage VDD = VBS = 15 V, THVIC = 25C, 10 k to 5 V Pull-up (Figure. 5) VFSDD Shut-down Detection level VIN(ON) ON Threshold Voltage VIN(OFF) V 11.2 VFT Shut-down Reset level V 10.7 VDD = VBS = 15 V, THVIC = 25C Fault-Out Pulse Width 0.5 0.55 Detection level HVIC Temperature Sensing Current tFOD 0.5 Reset level IFT VFSDR 0.45 Applied between VF - COM Applied between IN(UH), IN(VH), IN(WH), IN(UL), IN(VL), OFF Threshold Voltage IN(WL) - COM Note: 9. Short-circuit protection is functioning for all six IGBTs. 5.0 4.5 4.0 VF [V] 3.5 3.0 2.5 2.0 1.5 1.0 0 25 50 75 100 125 O THVIC [ C] Figure. 5. V-T Curve of Temperature Output of IC (5V pull-up with 10kohm) (c)2015 Semiconductor FNB51060TD1 Rev. 1.1 7 www.fairchildsemi.com www.onsemi.com FNB51060TD1 Motion SPM(R) 55 Series Control Part Symbol RBS Parameter Conditions Bootstrap Diode Resitance Min. Typ. Max. Unit - 280 - Min. Typ. Max. Unit - 300 400 V VDD = 15V, TC = 25C 0.06 0.05 IF [A] 0.04 0.03 0.02 0.01 o T J =25 C, V DD=15V 0.00 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 V F [V] Figure 6. Built-In Bootstrap Diode Charaterstics Recommended Operating Conditions Symbol Parameter Conditions VPN Supply Voltage Applied between P - NU, NV, NW VDD Control Supply Voltage Applied between VDD - COM 14.0 15 16.5 V VBS High - Side Bias Voltage Applied between VB(U) - VS(U), VB(V) - VS(V), VB(W) VS(W) 13.0 15 18.5 V -1 - 1 V / s dVDD / dt, Control Supply Variation dVBS / dt tdead Blanking Time for Preventing Arm - Short For each input signal 0.5 - - s fPWM PWM Input Signal - 40C TJ 150C - - 20 kHz VSEN Voltage for Current Sensing Applied between NU, NV, NW - COM (Including surge voltage) -4 4 V (Note 10) 0.7 - - s 0.7 - - PWIN(ON) Minimun Input Pulse PWIN(OFF) Width Note: 10. This product might not make response if input pulse width is less than the recommanded value. 5 V L in e (M C U o r C o n tro l p o w e r) R PF = 10k SPM IN (U H ) , IN (V H ) , IN (W H ) IN (U L ) , IN ( V L ) , IN (W L ) MCU V F COM Note: 11. RC coupling at each input (parts shown dotted) might change depending on the PWM control scheme used in the application and the wiring impedance of the application's printed circuit board. The input signal section of the SPM 55 product integrates 10 k(typ.) pull-down resistor. Therefore, when using an external filtering resistor, please pay attention to the signal voltage drop at input terminal. Figure 7. Recommended MCU I/O Interface Circuit (c)2015 Semiconductor FNB51060TD1 Rev. 1.1 8 www.fairchildsemi.com www.onsemi.com FNB51060TD1 Motion SPM(R) 55 Series Bootstrap Diode Part Parameter Device Flatness Mounting Torque Conditions See Figure 8 Min. Typ. Max. Unit -50 - 100 m Mounting Screw: - M3 Recommended 0.7 N * m 0.6 0.7 0.8 N*m Note Figure 9 Recommended 7.1 kg * cm 5.9 6.9 7.9 kg * cm - 6.0 - g Weight Figure 8. Flatness Measurement Position Figure 9. Mounting Screws Torque Order Note: 12. Do not make over torque when mounting screws. Much mounting torque may cause package cracks, as well as bolts and Al heat-sink destruction. 13. Avoid one side tightening stress. Figure 10 shows the recommended torque order for mounting screws. Uneven mounting can cause the ceramic substrate of the Motion SPM 55 product to be damaged. The Pre-screwing torque is set to 20 ~ 30 % of maximum torque rating. (c)2015 Semiconductor FNB51060TD1 Rev. 1.1 9 www.fairchildsemi.com www.onsemi.com FNB51060TD1 Motion SPM(R) 55 Series Mechanical Characteristics and Ratings FNB51060TD1 Motion SPM(R) 55 Series Time Charts of Protective Function Input Signal Protection Circuit State RESET SET RESET UVDDR a1 Control Supply Voltage a6 UVDDD a3 a2 a7 a4 Output Current a5 Fault Output Signal a1 : Control supply voltage rises: After the voltage rises UVDDR, the circuits start to operate when next input is applied. a2 : Normal operation: IGBT ON and carrying current. a3 : Under voltage detection (UVDDD). a4 : IGBT OFF in spite of control input condition. a5 : Fault output operation starts. a6 : Under voltage reset (UVDDR). a7 : Normal operation: IGBT ON and carrying current. Figure 10. Under-Voltage Protection (Low-Side) Input Signal Protection Circuit State RESET SET RESET UVBSR Control Supply Voltage b5 b1 UVBSD b3 b6 b2 b4 Output Current High-level (no fault output) Fault Output Signal b1 : Control supply voltage rises: After the voltage reaches UVBSR, the circuits start to operate when next input is applied. b2 : Normal operation: IGBT ON and carrying current. b3 : Under voltage detection (UVBSD). b4 : IGBT OFF in spite of control input condition, but there is no fault output signal. b5 : Under voltage reset (UVBSR) b6 : Normal operation: IGBT ON and carrying current Figure 11. Under-Voltage Protection (High-Side) (with the external shunt resistance and CR connection) (c)2015 Semiconductor FNB51060TD1 Rev. 1.1 10 www.fairchildsemi.com www.onsemi.com Lin d3 d4 d5 Ho d1 Hin : High-side Input Signal Lin : Low-side Input Signal Ho : High-side IGBT Gate Voltage Lo : Low-side IGBT Gate Voltage /Fo : Fault Output d2 Lo /Fo d1 : High Side First - Input - First - Output Mode d2 : Low Side Noise Mode : No Lo d3 : High Side Noise Mode : No Ho d4 : Low Side First - Input - First - Output Mode d5 : In - Phase Mode : No Ho Figure 12. Inter-Lock Function H IN L IN HO S m a rt T u rn - o ff S o ft O ff A c t iv a t e d b y n e x t in p u t a f t e r f a u lt c le a r LO CSC O v e r- C u rre n t D e t e c t io n N o O u tp u t VF HIN : High-side Input Signal LIN : Low-side Input Signal HO : High-Side Output Signal LO : Low-Side Output Signal CSC : Short-circuit Current Detection Input VF : Fault Out Function Figure 13. Fault-Out Function By Over Current Protection (c)2015 Semiconductor FNB51060TD1 Rev. 1.1 11 www.fairchildsemi.com www.onsemi.com FNB51060TD1 Motion SPM(R) 55 Series Hin L IN N o O u tp u t HO A c tiv a te d b y n e x t in p u t a f te r f a u lt c la e a r S m a rt T u rn - o ff S o ft O ff LO CSC VF E x te r n a l s h u td o w n in p u t HIN : High-side Input Signal LIN : Low-side Input Signal HO : High-Side Output Signal LO : Low-Side Output Signal CSC : Over Current Detection Input VF : Shutdown Input Function Figure 14. Shutdown Input Function By External Command (c)2015 Semiconductor FNB51060TD1 Rev. 1.1 12 www.fairchildsemi.com www.onsemi.com FNB51060TD1 Motion SPM(R) 55 Series H IN RS (9) IN(UH) Gating UH (19) VB(V) CBS (11) IN(VH) Gating VH (18) VB(W) M C U OUT(UH) IN(UH) IN(VH) OUT(VH) VS(V) V (3) M VB(W) CBSC RS (13) IN(WH) Gating WH IN(WH) (14) VDD 15V line CPS U (2) VS(U) VB(V) CBSC RS CBS P (1) VB(U) CBSC CPS CPS CSP15 CSPC15 CDCS OUT(WH) VS(W) (15) COM VDC VDD W (4) COM 5V line OUT(UL) RPF NU (5) CSPC05 CSP05 RS (17) VF Fault CBPF CPF RS (8) IN(UL) RS (10) IN(VL) Gating UL Gating VL RSU VF RS (12) IN(WL) Gating WL CSC RF Input Signal for Short-Circuit Protection NV (6) RSV IN(VL) IN(WL) OUT(WL) (16) CSC CPS CPS CPS OUT(VL) IN(UL) CSC NW (7) RSW U-Phase Current V-Phase Current W-Phase Current Temp. Monitoring Note: 1) To avoid malfunction, the wiring of each input should be as short as possible. (less than 2 ~ 3 cm) 2) By virtue of integrating an application specific type of HVIC inside the SPM(R) 55 product, direct coupling to MCU terminals without any opto-coupler or transformer isolation is possible. 3) VF is open-drain type. This signal line should be pulled up to the positive side of the MCU or control power supply with a resistor that makes IFO up to 5 mA. Please refer to Figure 15. 4) CSP15 of around seven times larger than bootstrap capacitor CBS is recommended. 5) Input signal is active-HIGH type. There is a 10 k resistor inside the IC to pull down each input signal line to GND. RC coupling circuits is recommanded for the prevention of input signal oscillation. RSCPS time constant should be selected in the range 50 ~ 150 ns. (Recommended RS = 100 , CPS = 1 nF) 6) To prevent errors of the protection function, the wiring around RF and CSC should be as short as possible. 7) In the short-circuit protection circuit, please select the RFCSC time constant in the range 1.5 ~ 2 s. 8) The connection between control GND line and power GND line which includes the NU, NV, NW must be connected to only one point. Please do not connect the control GND to the power GND by the broad pattern. Also, the wiring distance between control GND and power GND should be as short as possible. 9) Each capacitor should be mounted as close to the pins of the Motion SPM 55 product as possible. 10) To prevent surge destruction, the wiring between the smoothing capacitor and the P and GND pins should be as short as possible. The use of a high frequency non-inductive capacitor of around 0.1 ~ 0.22 F between the P and GND pins is recommended. 11) Relays are used at almost every systems of electrical equipments of home appliances. In these cases, there should be sufficient distance between the CPU and the relays. 12) The zener diode or transient voltage suppressor should be adopted for the protection of ICs from the surge destruction between each pair of control supply terminals. (Recommanded zener diode is 22 V / 1 W, which has the lower zener impedance characteristic than about 15 ) 13) Please choose the electrolytic capacitor with good temperature characteristic in CBS. Also, choose 0.1 ~ 0.2 F R-category ceramic capacitors with good temperature and frequency characteristics in CBSC. 14) For the detailed information, please refer to the application notes. Figur15. Typical Application Circuit (c)2015 Semiconductor FNB51060TD1 Rev. 1.1 13 www.fairchildsemi.com www.onsemi.com FNB51060TD1 Motion SPM(R) 55 Series (20) VB(U) CBS ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com (c) Semiconductor Components Industries, LLC N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 www.onsemi.com 1 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative www.onsemi.com