SM802149 156.25MHz/312.5MHz and 78.125MHz/156.25MHz LVDS Clock Synthesizer ClockWorksTM Flex General Description Features The SM802149 is a member of the ClockWorks family of devices from Micrel and provides an extremely low-noise timing solution. It is based on a unique patented ClockWorks Flex architecture that provides very low phase noise. * Generates eight differential LVDS clocks: either four at 156.25MHz and four at 312.5MHz, or four at 78.125MHz and four at 156.25MHz * 2.5V or 3.3V operating range * Typical phase jitter (1.875MHz to 20MHz): 99fs * Industrial temperature range * Green, RoHS, and PFOS compliant * Available in 44-pin 7mm x 7mm QFN package The device operates from a 3.3V or 2.5V power supply and synthesizes eight differential LVDS clocks, four at 156.25MHz and four at 3125MHz, or four at 78.125MHz and four at 156.25MHz. The SM802149 accepts a 26.04166MHz crystal or external LVCMOS input. Datasheets and support documentation are available on Micrel's web site at: www.micrel.com. Typical Application ClockWorks is a trademark of Micrel, Inc. Micrel Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel +1 (408) 944-0800 * fax + 1 (408) 474-1000 * http://www.micrel.com March 1, 2013 Revision 1.1 hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SM802149 Ordering Information(1) Part Number Marking Shipping Temperature Range Package SM802149UMG 802149 Tray -40C to +85C 44-Pin QFN SM802149UMGR 802149 Tape and Reel -40C to +85C 44-Pin QFN Note: 1. Devices are Green, RoHS, and PFOS compliant. Pin Configuration 44-Pin QFN 7mmx7mm (Top View) March 1, 2013 2 Revision 1.1 hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SM802149 Pin Description Pin Number Pin Name Pin Type Pin Level Pin Function 25, 26 28, 29 32, 33 35, 36 /Q1, Q1 /Q2, Q2 /Q3, Q3 /Q4, Q4 O, (DIF) LVDS Differential Clock Outputs from Bank 1 312.50MHz/156.25MHz 41, 42 1, 2 4, 5 7, 8 /Q5, Q5 /Q6, Q6 /Q7, Q7 /Q8, Q8 O, (DIF) LVDS Differential Clock Outputs from Bank 2 156.25MHz/78.125MHz 31, 37, 38 VDDO1 PWR Power Supply for the Outputs on Bank 1 43, 44, 16 VDDO2 PWR Power Supply for the Outputs on Bank 2 24, 39 VSSO1 PWR Power Supply Ground for the Outputs on Bank 1 3, 6, 40 VSSO2 PWR Power Supply Ground for the Outputs on Bank 2 23 GND I, (SE) This pin is not a Power Supply Ground, but MUST be tied to VSS I, (SE) Selects PLL Input Reference Source 0 = REF_IN 1 = XTAL 45k pull-up 10 XTAL_SEL LVCMOS 11, 20, 27, 30, 34 TEST 12, 13 VDD PWR Core Power Supply 21 VSS (Exposed Pad) PWR Core Power Supply Ground. The exposed pad must be connected to the VSS ground plane. PLL Bypass is a dual-function input. Normal operation selects output source. 0 = Normal PLL operation 1 = Output from crystal oscillator 45k pull-down Factory Test Pins. Do not connect anything to these pins. 9 PLL_BYPASS I, (SE) LVCMOS 18 XTAL_IN I, (SE) 10pF crystal Crystal Reference Input. No load caps needed. See Figure 5. 19 XTAL_OUT O, (SE) 10pF crystal Crystal Reference Output. No load caps needed. See Figure 5. 17 REF_IN I, (SE) LVCMOS 26.04166MHz Reference Clock Input LVCMOS Frequency Select. 1 = 312.5MHz/156.25 MHz 0 = 156.25MHz/78.125MHz. Internal 45k pull-up LVCMOS Output Enable. Q1-Q4 disables to tri-state. 0 = Disabled 1 = Enabled 45k pull-up LVCMOS Output Enable. Q5-Q8 disables to tri-state. 0 = Disabled 1 = Enabled 45k pull-up 14 15 22 March 1, 2013 FSEL OE1 OE2 I, (SE) I, (SE) I, (SE) 3 Revision 1.1 hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SM802149 Truth Tables PLL_BYPASS XTAL_SEL OE1 OE2 0 1 1 PLL 1 1 1 XTAL/REF_IN 0 1 1 REF_IN 1 1 1 XTAL 0 1 Q1-4 Tri-State 1 0 Q5-8 Tri-State FSEL Output Frequency (MHz) 0 156.25/78.125 1 312.50/156.25 March 1, 2013 4 INPUT OUTPUT Revision 1.1 hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SM802149 Absolute Maximum Ratings(2) Operating Ratings(3) Supply Voltage (VDD, VDDOX)........................................ +4.6V Input Voltage (VIN) .................................. -0.5V to VDD+0.5V Lead Temperature (soldering, 20s) ............................ 260C Case Temperature ..................................................... 115C Storage Temperature (Ts)......................... -65C to +150C Supply Voltage (VDD, VDDOX) ................. +2.375V to +3.465V Ambient Temperature (TA) .......................... -40C to +85C (4) Junction Thermal Resistance QFN (JA) Still-Air ......................................................... 24C/W QFN (JB) Junction to Board .......................................... 8C/W DC Electrical Characteristics(5) VDD = VDDO1/2 = 3.3V 5% or 2.5V 5%, VDD = 3.3V 5%, VDDO1/2 = 3.3V 5% or 2.5V 5%, TA = -40C to +85C. Symbol Parameter Condition Min. Typ. Max. Units 3.3V Operating Voltage VDDO1 = VDDO2 3.135 3.3 3.465 V 2.5V Operating Voltage VDDO1 = VDDO2 2.375 2.5 2.625 V Outputs loaded 156.25MHz 181 235 Outputs loaded 312.5MHz 216 280 VDD, VDDO1/2 mA LVCMOS Input (OE1, OE2, PLL_BYPASS) DC Electrical Characteristics(5) VDD = 3.3V 5%, or 2.5V 5%, TA = -40C to +85C. Symbol Parameter Condition VIH Input High Voltage VIL Input Low Voltage IIH Input High Current VDD = VIN = 3.465V IIL Input Low Current VDD = 3.465V, VIN = 0V Min. Typ. Max. Units 2 VDD + 0.3 V -0.3 0.8 V 150 A -150 A REF_IN DC Electrical Characteristics(5) VDD = 3.3V 5%, or 2.5V 5%, TA = -40C to +85C. Symbol Parameter VIH Input High Voltage VIL Input Low Voltage IIN Input Current Condition Min. VIN = 0V to VDD Typ. Max. Units 1.1 VDD + 0.3 V -0.3 0.6 V -5 5 A Notes: 2. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this datasheet. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 3. The datasheet limits are not guaranteed if the device is operated beyond the operating ratings. 4. Package thermal resistance assumes exposed pad is soldered (or equivalent) to the device's most negative potential on the PCB. 5. The circuit is designed to meet the AC and DC specifications shown in the above tables after thermal equilibrium has been established. March 1, 2013 5 Revision 1.1 hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SM802149 Crystal Characteristics Parameter Condition Mode of Oscillation 10pF load Min. Typ. Max. Units Fundamental, Parallel Resonant Frequency 26.04166 MHz Equivalent Series Resistance (ESR) 50 Shunt Capacitor, C0 1 5 pF Correlation Drive Level 10 100 W LVDS OUTPUT DC Electrical Characteristics(5) VDD = VDDO1/2 = 3.3V 5% or 2.5V 5%, VDD = 3.3V 5%, VDDO1/2 = 3.3V 5% or 2.5V 5%, TA = -40C to +85C. RL = 100 across Q and /Q. Symbol Parameter Condition Min. Typ. Max. Units VOD Differential Output Voltage Figure 1, Figure 4 275 350 475 mV VOD VOD Magnitude Change 40 mV VOS Offset Voltage 1.50 V VOS VOS Magnitude Change 50 mV Max. Units 1.15 1.25 AC Electrical Characteristics(5, 6) VDD = VDDO1/2 = 3.3V 5% or 2.5V 5%, VDD = 3.3V 5%, VDDOX1/2= 3.3V 5% or 2.5V 5%, TA = -40C to +85C. Symbol Parameter Condition Output Frequency 1 FSEL = 1, Q1-Q4 312.5 MHz Output Frequency 2 FSEL = 1, Q5-Q8 156.25 MHz Output Frequency 1 FSEL = 0, Q1-Q4 156.25 MHz Output Frequency 2 FSEL = 0, Q5-Q8 78.125 MHz TR/TF Output Rise/Fall Time 20%-80%, Figure 2, Figure 4 TSKEW Output-to-Output Skew Within bank. Note 7 ODC Output Duty Cycle LVDS outputs TLOCK PLL Lock Time FOUT FOUT (8) RMS Phase Jitter (Output = 156.25MHz) (8) RMS Phase Jitter (Output = 312.5MHz) Min. 100 48 Typ. 220 50 400 ps 45 ps 52 % 20 ms Integration range: 12kHz-20MHz 260 fs Integration range: 1.875MHZ-20MHz 105 fs Integration range: 12kHz-20MHz 250 fs Integration range: 1.875MHz-20MHz 99 fs Notes: 6. All phase noise measurements were taken with an Agilent 5052B phase noise system. 7. Defined as skew between outputs at the same supply voltage and with equal load conditions; Measured at the output differential crossing points. 8. Measured using a 26.04166 MHz crystal as the input reference source. If using an external reference input, use a low phase noise source. With an external reference, the phase noise will follow the input source phase noise up to about 1MHz. March 1, 2013 6 Revision 1.1 hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SM802149 Phase Noise Plots 156.25MHz LVDS Integrated Jitter 12kHz-20MHz = 262fs 156.25MHz LVDS Integrated Jitter 1.875MHz-20MHz = 105fs March 1, 2013 7 Revision 1.1 hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SM802149 Phase Noise Plots (Continued) 312.5MHz LVDS Integrated Jitter 12kHz-20MHz = 252fs 312.5MHz LVDS Integrated Jitter 1.875MHz-20MHz = 99fs March 1, 2013 8 Revision 1.1 hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SM802149 Contact Micrel's HBW applications group if you need assistance to select a suitable crystal for your application at hbwhelp@micrel.com Application Information Input Reference When operating with a crystal input reference, do not apply a switching signal to REF_IN. LVDS Outputs Terminate LVDS outputs with 100 across Q and /Q. For best performance, load all outputs. Outputs can be DC or AC-coupled. Crystal Layout Keep the layers under the crystal as open as possible and do not place switching signals or noisy supplies under the crystal. Crystal load capacitance is built inside the die so no external capacitance is needed. See the Selecting a Quartz Crystal for the Clockworks Flex I Family of Precision Synthesizers application note for further details. Figure 1. Duty Cycle Timing Figure 2. All Outputs Rise/Fall Time Figure 3. RMS Phase/Noise/Jitter March 1, 2013 9 Revision 1.1 hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SM802149 Figure 4. LVDS Output Load March 1, 2013 Figure 5. Crystal Input Interface 10 Revision 1.1 hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SM802149 Package Information(9) 44-pin 7mm x 7mm QFN package Note: 9. Package information is correct as of the publication date. For updates and most current information, go to www.micrel.com. MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this data sheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel's terms and conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2013 Micrel, Incorporated. March 1, 2013 11 Revision 1.1 hbwhelp@micrel.com or (408) 955-1690 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Micrel: SM802140UMG SM802140UMG TR SM802140UMG-TR