ASM705 / 706 / 707 / 708 ASM813L October 2003 rev 1.0 Low Power P Supervisor Circuits General Description Features * Precision power supply monitor The ASM705 / 706 / 707 / 708 and AS813L are cost effective *4.64V threshold (ASM705/707/813L) CMOS supervisor circuits that monitor power-supply and *4.40V threshold (ASM706/708) battery voltage level, and P/C operation. * Debounced manual reset input * Voltage monitor The family offers several functional options. Each device *1.25V threshold generates a reset signal during power-up, power-down and *Battery monitor / Auxiliary supply monitor during brownout conditions. A reset is generated when the * Watchdog timer (ASM705/706/813L) supply drops below 4.65V (ASM705/707/813L) or 4.40V * 200ms reset pulse width (ASM706/708). For 3V power supply applications, refer to the * Active HIGH reset output (ASM707/708/813L) ASM705P/R/S/T data sheet. In addition, the ASM705/706/813L * MicroSO package feature a 1.6 second watchdog timer. The ASM707/708 have both active-HIGH and active-LOW reset outputs but no watchdog function. The ASM813L has the same pin-out and functions as the ASM705 but has an active-HIGH reset output. A versatile power-fail circuit has a 1.25V threshold, useful in low battery detection and for monitoring non-5V supplies. All devices have a manual reset (MR) input. The watchdog timer output will trigger a reset if connected to MR. All devices are available in 8-pin DIP, SO and MicroSO Applications * Computers and embedded controllers * Portable/Battery-operated systems * Intelligent instruments * Wireless communication systems * PDAs and hendheld equipment * Automative Systems * Safety Systems packages. Typical Operating Circuit Unregulated DC +5V Regulator VCC R1 VCC PFI R2 RESET (RESET) ASM705 WDI ASM706 (ASM813L) WDO P RESET (RESET) I/O LINE NMI MR PFO INTERRUPT Alliance Semiconductor 2575 Augustine Drive . Santa Clara, CA 95054 . Tel: 408.855.4900 . Fax: 408.855.4999 . www.alsc.com Notice: The information in this document is subject to change without notice ASM705 / 706 / 707 / 708 ASM813L October 2003 rev 1.0 Block Diagrams Transition Detector WDI Watchdog Timer WDO RESET VCC VCC Timebase 0.25mA MR 0.25mA RESET Generator RESET (RESET) ASM813L + VCC + MR RESET Generator + VCC - + 4.65V (ASM705/813L) 4.40V (ASM706) PFI 4.65V (ASM707) 4.40V (ASM708) + PFO - 1.25V - PFI + ASM705 ASM706 ASM813L RESET ASM707 ASM708 PFO - 1.25V GND GND Pin Configuration MicroSO DIP/SO MR 1 8 RESET VCC 2 ASM707 7 RESET GND 3 ASM708 PFI 4 MR 1 VCC 2 8 WDO 6 NC ASM705 7 RESET (RESET) ASM706 GND 3 (ASM813L)6 WDI 5 PFO PFI 4 5 PFO 8 NC RESET (RESET) 1 RESET 2 ASM707 7 PFO RESET 2 MR 3 ASM708 6 PFI VCC 4 5 GND RESET 1 Low Power P Supervisor Circuits Notice: The information in this document is subject to change without notice 8 ASM705 7 ASM706 MR 3 (ASM813L) 6 VCC 4 5 WDI PFO PFI GND 2 of 15 ASM705 / 706 / 707 / 708 ASM813L October 2003 rev 1.0 Pin Description Pin Number ASM705/706 DIP/ SO MicroSO ASM707/708 DIP/ SO ASM813L MicroSO DIP/ SO Name Function MicroSO 1 3 1 3 1 3 MR Manual reset input. The active LOW input triggers a reset pulse. A 250 A pull-up current allows the pin to be driven by TTL/CMOS logic or shorted to ground with a switch. 2 4 2 4 2 4 VCC +5V power supply input. 3 5 3 5 3 5 GND Ground reference for all signals. 4 6 4 6 4 6 PFI Power-fail input voltage monitor. With PFI less than 1.25V, PFO goes LOW. Connect PFI to Ground or VCC when not in use. 5 7 5 7 5 7 PFO Power-fail output. The output is active LOW and sinks current when PFI is less than 1.25V. 6 8 - - 6 8 WDI Watchdog input. WDI controls the internal watchdog timer. A HIGH or LOW signal for 1.6sec at WDI allows the internal timer to run-out, setting WDO LOW. The watchdog function is disabled by floating WDI or by connecting WDI to a high impedance three-state buffer. The internal watchdog timer clears when: RESET is asserted; WDI is three-stated ; or WDI sees a rising or falling edge. - - 6 8 - - NC Not Connected 7 1 7 1 - - RESET Active LOW reset output. Pulses LOW for 200ms when triggered, and stays LOW whenever VCC is below the reset threshold (ASM705: 4.65V, ASM705J: 4.00V, ASM706: 4.40V). RESET remains LOW for 200ms after VCC rises above the reset threshold or MR goes from LOW to HIGH. A watchdog timeout will not trigger RESET unless WDO is connected to MR. Watchdog output. WDO goes LOW when the 1.6 second internal watchdog timer times-out and does not go HIGH until the watchdog is cleared. In addition, when VCC falls below the reset threshold, WDO goes LOW. Unlike RESET, WDO does not have a minimum pulse width and as soon as VCC exceeds the reset threshold, WDO goes HIGH with no delay. 8 2 - - 8 2 WDO - - 8 2 7 1 RESET Active HIGH reset output. The inverse of RESET. The ASM813L has only a RESET output. Low Power P Supervisor Circuits Notice: The information in this document is subject to change without notice 3 of 15 ASM705 / 706 / 707 / 708 ASM813L October 2003 rev 1.0 Detailed Description A proper reset input VRT enables a microprocessor / microcontroller to start in a known state. ASM70X and 5V VCC tRS 0V ASM813L assert reset to prevent code execution errors tRS 5V during power-up, power-down and brown-out conditions. RESET 0V RESET/RESET Timing The RESET/RESET signals are designed to start a P/C in a known state or return the system to a known state. 5V MR The ASM707/708 have two RESET outputs, one active-HIGH RESET and one active-LOW RESET output. The ASM813L 0V MR externally set low 5V tMD tMR WDO 0V has only an active-HIGH output. RESET is simply the complement of RESET. Figure 1: WDI Three-state operation RESET is guaranteed to be LOW with VCC above 1.2V. During a power-up sequence, RESET remains low until the supply rises above the threshold level, either 4.65V, 4.40V or 4.00V. RESET goes high approximately 200ms after crossing the threshold. Manual Reset (MR) The active-LOW manual reset input is pulled high by a 250A pull-up current and can be driven low by CMOS/TTL logic or a mechanical switch to ground. An external debounce circuit During power-down, RESET goes LOW as VCC falls below the threshold level and is guaranteed to be under 0.4V with VCC above 1.2V. is unnecessary since the 140ms minimum reset time will debounce mechanical pushbutton switches. By connecting the watchdog output (WDO) and MR, a watchdog timeout forces RESET to be generated. The In a brownout situation where VCC falls below the threshold ASM813L should be used when an active-HIGH RESET is level, RESET pulses low. If a brownout occurs during an required. already initiated reset, the pulse will continue for a minimum of 140ms. Watchdog Timer The watchdog timer available on the ASM705/706/813L Power Failure Detection With Auxiliary Comparator monitors P/C activity. An output line on the processor is All devices have an auxiliary comparator with 1.25V trip point used to toggle the WDI line. If this line is not toggled within and uncommitted output (PFO) and noninverting input (PFI). 1.6 seconds, the internal timer puts the watchdog output, This comparator can be used as a supply voltage monitor WDO, into a LOW state. WDO will remain LOW until a toggle with an external resistor voltage divider. The attenuated is detected at WDI. voltage at PFI should be set just below the 1.25 threshold. As the supply level falls, PFI is reduced causing the PFO output If WDI is floated or connected to a three-stated circuit, the to transit LOW. Normally PFO interrupts the processor so the watchdog function is disabled, meaning, it is cleared and not system can be shut down in a controlled manner. counting. The watchdog timer is also disabled if RESET is asserted. When RESET becomes inactive and the WDI input sees a high or low transition as short as 50ns, the watchdog timer will begin a 1.6 second countdown. Additional Low Power P Supervisor Circuits Notice: The information in this document is subject to change without notice 4 of 15 ASM705 / 706 / 707 / 708 ASM813L October 2003 rev 1.0 transitions at WDI will reset the watchdog timer and initiate a new countdown sequence. BUF Buffered RESET WDO will also become LOW and remain so, whenever the supply voltage, VCC , falls below the device threshold level. VCC WDO goes HIGH as soon as VCC transitions above the threshold. There is no minimum pulse width for WDO as there is for the RESET outputs. If WDI is floated, WDO essentially acts as a low-power output indicator. Supply Voltage ASM70x C or P 4.7k RESET RESET Input GND GND WDI Bi-directional I/O Pin Figure 3: Bi-directional Reset Pin Interfacing WDO Monitoring Voltages Other Than VCC The ASM705-708 can monitor voltages other than VCC using the Power Fail circuitry. If a resistive divider is connected RESET from the voltage to be monitored to the Power Fail input (PFI), the PFO will go LOW if the voltage at PFI goes below 1.25V reference. Should hysteresis be desired, connect a resistor (equal to approximately 10 times the sum of the two RESET resistors in the divider) between the PFI and PFO pins. A capacitor between PFI and GND will reduce circuit sensitivity Figure 2: Watchdog Timing to input high-frequency noise. If it is desired to assert a RESET in addition to the PFO flag, this may be achieved by Application Information connecting the PFO output to MR. Ensuring That RESET is Valid Down to VCC = 0V VIN +5V When VCC falls below 1.1V, the ASM705-708 RESET output no longer pulls down; it becomes indeterminate. To avoid the possibility that stray charges build up and force RESET to the VCC R1 MR wrong state, a pull-down resistor should be connected to the RESET pin, thus draining such charges to ground and ASM70X PFO PFI holding RESET low. The resistor value is not critical. A 100k resistor will pull RESET to ground without loading it. R2 GND RESET To P Bi-directional Reset Pin Interfacing The ASM705/6/7/8 can interface with P/C bi-directional reset pins by connecting a 4.7k resistor in series with the RESET output and the P/C bi-directional RESET pin. Figure 4: Monitoring +5V and an additional supply VIN Low Power P Supervisor Circuits Notice: The information in this document is subject to change without notice 5 of 15 ASM705 / 706 / 707 / 708 ASM813L October 2003 rev 1.0 VCC Monitoring a Negative Voltage + The Power-Fail circuitry can also monitor a negative supply rail. When the negative rail is OK, PFO will be LOW, and when the negative rail is failing (not negative enough), PFO R1 R3 VCC goes HIGH (the opposite of when positive voltages are MR monitored). To trigger a reset, these outputs need to be R4 inverted: adding the resistors and transistor as shown achieves this. The RESET output will then have the same sense as for positive voltages: good = HIGH, bad = LOW. It should be noted that this circuit's accuracy depends on the PFI ASM70X PFO 2N3904 R2 GND RESET VCC line, the PFI threshold tolerance, and the resistors. To P VCC - 1.25 Negative Input Voltage R1 = 1.25 - VTRIP R2 Figure 5: Monitoring a negative voltage Low Power P Supervisor Circuits Notice: The information in this document is subject to change without notice 6 of 15 ASM705 / 706 / 707 / 708 ASM813L October 2003 rev 1.0 Absolute Maximum Ratings Parameter Min Max Unit VCC -0.3 6.0 V All other inputs 1 -0.3 VCC + 0.3 V 20 mA Output Current: All outputs 20 mA Rate of Rise at VCC 100 V/s Plastic DIP Power Dissipation (Derate 9mW/C above 70C) 700 mV SO Power Dissipation (Derate 5.9mW/C above 70C) 470 mW` MicroSO Power Disspation (Derate 4.1mW/C above 70C) 330 mW -40 +85 C 0 70 C -65 160 C 300 C Pin Terminal Voltage with Respect to Ground Input Current at VCC and GND Operating Temperature Range ASM705E/706E/707E/708E/813LE ASM706C/707C/708C/813LC Storage Temperature Range Lead Temperature Soldering (10sec) Note: 1. The input voltage limits of PFI and MR can be exceeded if the input current is less than 10mA. These are stress ratings only and functional operation is noy implied. Exposure to absolute maximum ratings for prolonged time periods may affect device reliability. Low Power P Supervisor Circuits Notice: The information in this document is subject to change without notice 7 of 15 ASM705 / 706 / 707 / 708 ASM813L October 2003 rev 1.0 Electrical Characteristics Unless otherwise noted, specifications are over the operating temperature range and VCC supply voltages are 2.7V to 5.5V (ASM706P, ASM708R), 3.0 V to 5.5V (ASM706/708S), 3.15V to 5.5V (ASM706/708T) and 4.1V to 5.5.V (ASM706/708J) Parameter Operating Voltage Range Supply Current RESET Threshold Symbol VCC ICC VRT RESET Threshold Hysteresis tRS MR Pulse Width tMR MR to RESET Out Delay tMD MR Pullup current Max 1.2 5.5 ASM813L 1.1 5.5 ASM705/6/7/8E, ASM813E 1.2 5.5 ASM705/706C/813LC 75 140 ASM705E/706E/813LE 75 140 ASM707C/708C 50 140 ASM707E/708E 50 140 ASM705/707/813L, Note 2 4.50 4.65 4.75 ASM706/708 Note 2 4.25 4.40 4.50 Note 2 140 200 V A V 280 ms s 0.25 Note 2 VIH Unit mV 40 0.15 2.0 0.8 VIL s V 600 A ISINK = 3.2mA 0.4 V ASM705/5/7/8, VCC = 1.2V, ISINK = 100A 0.3 MR = 0V ASM707/8/813L, ISOURCE = 800A RESET Output Voltage Typ ASM705/6/7/8C ISOURCE = 800A RESET Output Voltage Min Note 2 RESET Pulse Width MR Input Threshold Conditions 100 250 VCC - 1.5 VCC-1.5 ASM707/8, ISINK = 1.2A 0.4 ASM813L, ISINK =3.2A 0.4 ASM813L, VCC = 1.2V, ISOURCE = 4A V 0.9 Low Power P Supervisor Circuits Notice: The information in this document is subject to change without notice 8 of 15 ASM705 / 706 / 707 / 708 ASM813L October 2003 rev 1.0 Parameter Symbol Conditions Min Typ Max Unit 1.00 1.60 2.25 s Watchdog Timeout Period tWD ASM705/6/813L WDI Pulse Width tWP VIL = 0.4V, VIH=0.8VCC, 50 VIH ASM705/706/813L, VCC = 5V 3.5 WDI Input Threshold 0.8 VIL ASM705/6/813L, WDI = VCC WDI Input Current ASM705/6/813L, WDI = 0V WDO Output Voltage VOH ASM705/6/813L, ISOURCE = 800A VOL ASM705/6/813L, ISINK = 1.2mA VCC = 5V PFI Input Threshold PFI Input Current PFO Output Voltage ns VOH ISOURCE = 800A VOL ISINK = 3.2mA 50 -150 150 -50 VCC - 1.5 0.4 V A V 1.2 1.25 1.3 V -25 0.01 25 nA VCC - 1.5 0.4 V Notes 2: RESET (ASM705/6/7/8, RESET(ASM707/8, ASM813L) Low Power P Supervisor Circuits Notice: The information in this document is subject to change without notice 9 of 15 ASM705 / 706 / 707 / 708 ASM813L October 2003 rev 1.0 Package Dimensions 8-Pin MicroSO D E1 E A2 A a C 0.10mm 0.004in e A1 b Inches L Millimeteres Min Max Min Max A - 0.0433 - 0.10 A1 0.0020 0.0059 0.050 0.15 A2 0.0295 0.0374 0.75 0.95 b 0.0098 0.0157 0.25 0.40 C 0.0051 0.0091 0.13 0.23 D 0.1142 0.1220 2.90 3.10 e 0.0256 BSC 0.65 BSC E 0.193 BSC 4.90 BSC E1 0.1142 0.1220 2.90 3.10 L 0.0157 0.0276 0.40 0.70 a 0 6 0 6 Low Power P Supervisor Circuits Notice: The information in this document is subject to change without notice 10 of 15 ASM705 / 706 / 707 / 708 ASM813L October 2003 rev 1.0 Package Dimensions (contd) Plastic DIP (8-Pin) D1 E D E1 A1 A L b2 b e 0 -15 eA eC eB Inches Millimeteres Min Max Min Max A - 0.210 - 5.33 A1 0.015 - 0.38 - A2 0.115 0.195 2.92 4.95 b 0.014 0.022 0.36 0.56 b2 0.045 0.070 1.14 1.78 b3 0.030 0.045 0.80 1.14 D 0.355 0.400 9.02 10.16 D1 0.005 - 0.13 - E 0.300 0.325 7.62 8.26 E1 0.240 0.280 6.10 7.11 e 0.100 - 2.54 eA 0.300 - 7.62 eB - 0.430 - 10.92 eC - 0.060 L 0.115 0.150 2.92 3.81 Low Power P Supervisor Circuits Notice: The information in this document is subject to change without notice 11 of 15 ASM705 / 706 / 707 / 708 ASM813L October 2003 rev 1.0 Package Dimensions (contd) SO (8-Pin) Inches Millimeteres Min Max Min Max A 0.053 0.069 1.35 1.75 A1 0.004 0.010 0.10 0.25 B 0.013 0.020 0.33 0.51 C 0.007 0.010 0.19 0.25 e 0.050 1.27 E 0.150 0.157 3.80 4.00 H 0.228 0.244 5.80 6.20 L 0.016 0.050 0.40 1.27 D 0.189 0.197 4.80 2.00 Low Power P Supervisor Circuits Notice: The information in this document is subject to change without notice 12 of 15 ASM705 / 706 / 707 / 708 ASM813L October 2003 rev 1.0 Ordering Codes Part Number Reset Threshold (V) Temperature Range Pins-Package ASM705 Active LOW Reset, Watchdog Output And Manual RESET ASM705CPA 4.65 0C to +70 C 8-Plastic DIP ASM705CSA 4.65 0C to +70 C 8-SO ASM705CUA 4.65 0C to +70 C 8-MicroSO ASM705C/D 4.65 25C Dice ASM705EPA 4.65 -40C to +85C 8-Plastic DIP ASM705ESA 4.65 -40C to +85C 8-SO ASM706 Active LOW Reset, Watchdog Output And Manual RESET ASM706CPA 4.40 0C to +70 C 8-Plastic DIP ASM706CSA 4.40 0C to +70 C 8-SO ASM706CUA 4.40 0C to +70 C 8-MicroSO ASM706C/D 4.40 25C Dice ASM706EPA 4.40 -40C to +85C 8-Plastic DIP ASM706ESA 4.40 -40C to +85C 8-SO ASM707 Active LOW & HIGH Reset with Manual RESET ASM707CPA 4.65 0C to +70 C 8-Plastic DIP ASM707CSA 4.65 0C to +70 C 8-SO ASM707CUA 4.65 0C to +70 C 8-MicroSO ASM707C/D 4.65 25C Dice ASM707EPA 4.65 -40C to +85C 8-Plastic DIP ASM707ESA 4.65 -40C to +85C 8-SO ASM708Active LOW & HIGH Reset with Manual RESET ASM708CPA 4.40 0C to +70 C 8-Plastic DIP ASM708CSA 4.40 0C to +70 C 8-SO ASM708CUA 4.40 0C to +70 C 8-MicroSO ASM708C/D 4.40 25C Dice ASM708EPA 4.40 -40C to +85C 8-Plastic DIP ASM708ESA 4.40 -40C to +85C 8-SO contd... Low Power P Supervisor Circuits Notice: The information in this document is subject to change without notice 13 of 15 ASM705 / 706 / 707 / 708 ASM813L October 2003 rev 1.0 Part Number Reset Threshold (V) Temperature Range Pins-Package ASM813L Active HIGH Reset, Watchdog Output And Manual RESET ASM813LCPA 4.65 0C to +70 C 8-Plastic DIP ASM813LCSA 4.65 0C to +70 C 8-SO ASM813LCUA 4.65 0C to +70 C 8-MicroSO ASM813LC/D 4.65 25C Dice ASM813LEPA 4.65 -40C to +85C 8-Plastic DIP ASM813LESA 4.65 -40C to +85C 8-SO Feature Summary ASM705 ASM706 ASM707 ASM708 ASM813L Power fail detector Brownout detection Manual RESET input Power-up/down RESET Watchdog Timer Active HIGH RESET output Active LOW RESET output RESET Threshold (V) 4.65/4.00 4.40 4.65 4.40 4.65 Low Power P Supervisor Circuits Notice: The information in this document is subject to change without notice 14 of 15 ASM705 / 706 / 707 / 708 ASM813L Alliance Semiconductor Corporation 2575, Augustine Drive, Santa Clara, CA 95054 Tel: 408 - 855 - 4900 Fax: 408 - 855 - 4999 www.alsc.com Copyright (c) Alliance Semiconductor All Rights Reserved Part Number:ASM705 / 706 / 707 / 708 ASM813L Document Version: 1.0 (c) Copyright 2003 Alliance Semiconductor Corporation. All rights reserved. Our three-point logo, our name and Intelliwatt are trademarks or registered trademarks of Alliance. All other brand and product names may be the trademarks of their respective companies. Alliance reserves the right to make changes to this document and its products at any time without notice. Alliance assumes no responsibility for any errors that may appear in this document. The data contained herein represents Alliance's best data and/or estimates at the time of issuance. Alliance reserves the right to change or correct this data at any time, without notice. If the product described herein is under development, significant changes to these specifications are possible. The information in this product data sheet is intended to be general descriptive information for potential customers and users, and is not intended to operate as, or provide, any guarantee or warrantee to any user or customer. Alliance does not assume any responsibility or liability arising out of the application or use of any product described herein, and disclaims any express or implied warranties related to the sale and/or use of Alliance products including liability or warranties related to fitness for a particular purpose, merchantability, or infringement of any intellectual property rights, except as express agreed to in Alliance's Terms and Conditions of Sale (which are available from Alliance). All sales of Alliance products are made exclusively according to Alliance's Terms and Conditions of Sale. The purchase of products from Alliance does not convey a license under any patent rights, copyrights; mask works rights, trademarks, or any other intellectual property rights of Alliance or third parties. Alliance does not authorize its products for use as critical components in life-supporting systems where a malfunction or failure may reasonably be expected to result in significant injury to the user, and the inclusion of Alliance products in such life-supporting systems implies that the manufacturer assumes all risk of such use and agrees to indemnify Alliance against all claims arising from such use.