4 3 NO. SH REV. 1 CTR3522-1 110 This print and associated documents and the contained REVISIONS information are the confidential property of ELECTRONIC INSTALLATION INSTRUCTIONS EcN | ZONE | REV DESCRIPTION DATE APPROVED CABLE SPECIALISTS. Disclosure of, and/or reproduction of, all or part thereof or manufacture of any part from |1. BEGIN BY CUTTING THE CABLE OFF SQUARE. 2975 IN/C] NEW RELEASE. 8/18/95 JBH information contained on this print not specifically per 30 4443 A | SEE ECN# 4443 8/13/96 JBH mitted by ELECTRONIC CABLE SPECIALISTS in writing Is SP 6189 a | SEE ECN# 6189 9710798) MCT 12885 C }| SEE ECN 12/7/00 CAC Body 2. STRIP THE CABLE AS SHOWN, BEGINNING WITH L1 AND ENDING 13466 D | SEE ECN Peder {Chama +- 1.560 WITH L2. TAKE CARE NOT TO NICK THE CONDUCTORS WHILE I FERRULE g STRIPPING THE DIELECTRIC AND JACKET. THE USE OF A 9. SLIDE THE BODY OF THE CONNECTOR OVER THE END OF THE CABLE UNTIL THE zl 3 STRIPPER DESIGNED FOR COAXIAL CABLE IS RECOMMENDED. NOTCH IN THE CONTACT SEATS WITH THE DIELECTRIC RIDGE INSIDE THE CONNECTOR. 5 -{-500 [ 2 <r pou = .29 L2 = .61 CABLE CONTACT : PUSH CABLE INTO THE CONNECTOR 3. SLIDE THE FERRULE AND ADHESIVE SHRINK TUBING STRAIGHT, TO AVOID KINKING THE CABLE. | OVER THE END OF THE CABLE. \ 10, DIELECTRIC STIFFENER <_[ Toe C4 4. USING TWEEZERS, FOLD THE OUTER BRAID BACK OVER DIMENSIONS /\ THE CABLE JACKET, LEAVING AS MUCH WEAVE AS POSSIBLE. SPECIFICATIONS a RI 11. SUDE THE FERRULE OVER THE SHIELDS AND AGAINST THE CONNECTOR BODY. IMPEDANCE: 50 OHMS NOMINAL TRIM AWAY ANY EXCESS BRAID. CRIMP THE FERRULE ONCE, NEXT TO THE FREQUENCY RANGE: 0-11 GHz 5. USING TWEEZERS, FOLD THE INNER BRAID BACK OVER BODY, USING A M22520/511 DIE (A HEX) IN A M22520/5-01 VSWR: 1.2:1 MAXIMUM DC TO 2GHz THE OTHER SHIELD, LEAVING AS MUCH WEAVE AS POSSIBLE. TOOL FRAME. APPLY ADHESIVE HEAT SHRINK. INSERTION LOSS: .1dB MAXIMUM DC TO 2GHz WORKING VOLTAGE: 500 VRMS SEA LEVEL <__[__ | 8 re DIELECTRIC WITHSTANDING: 1500 VRMS @ SEA LEVEL INSULATION RESISTANCE: 5000 MEGOHMS MINIMUM @ 500 VOLTS OC MECHANICAL REMOVE THE DIELECTRIC FROM THE CENTER CONDUCTOR BACK NOT CONNECTOR INTERFACE: Oe aS PeR MIL-STD348A TO THE BEGINNING OF THE FOLDED BACK SHIELD, APPROxiMareLy NOTES c = 1. ALL DIMENSIONS ARE IN INCHES. TERMINATION STYLE: CABLE CONTACT-SOLDER OR CRIMP on erut NOT TO wex ONE center CONDOR ISAS . FERRULE-CRIMP . CABLE RETENTION: 20 LES STRIPPERS ARE RECOMMENDED. A ENSURE HEAT SHRINK 1S INSTALLED PRIOR TO CRIMPING CONNECTOR. VIRONMENTA |___}. 60 Lv ADHESIVE HEAT SHRINK SHOULD SE APPLIED IN ACCORDANCE WITH ENVIRONMENTAL a a TEMPERATURE RATING: -68' TO +168" C ECS WORK INSTRUCTION WI0007. CONTACT ECS FOR A COPY OF THIS WORK VIBRATION: MIL-STD-202, METHOD 204, COND. 8 INSTRUCTION, SHOCK: MIL-STO-202, METHOD 213, COND. | CONNECTOR DIMENSIONS ARE FOR REFERENCE ONLY. THERMAL SHOCK: MIL~STD~202, METHOD 107, COND. 8 |7 INSTALL DIELECTRIC STIFFENER OVER CENTER CONDUCTOR, 5. DELETED. CORROSION: MIL-STD-202, METHOD 101, COND. B MOISTURE RESISTANCE: MIL-STD-202, METHOD 106 ENSURING THAT fT iS BUTTEO AGAINST THE CABLE DIELECTRIC. 6. DELETED. BODY: BRASS PER QQ-B-626 ALL LENGTHS IN INCHES Evectronic CaBle 5 PECIALISTS FERRULE: ANNEALED BRASS PER QQ8-626 Ecs PHONE: (414) 421-5300 CABLE CONTACT: BERYLLIUM COPPER PER QQC-530 8. SOLDER THE CONTACT ONTO THE CENTER CONDUCTOR, PER APPROVALS ote CENTER CONTACT: GRASS FER QQ-B-626 MIL-STD-2000, USING 63Sn/37Pb SOLDER OR CRIMP OUR TT aan la/s/ost CUSTOMER _ SPECIFICATION DIELECTRIC: | TEFLON PER. L=P=403 BUTTED AGAINST THE DIELECTRIC. STIPFENER. CLEAN ALL FLUX [EEoewuews [a/18/98 RIGHT ANGLE, TNC, PLUG . _p- . Al GASKET: SILICONE RUBBER PER ZZ-R-765 RESIDUES USING AN APPROPRIATE FLUX CLEANER. DESIGNED BY: FINISHES SIZE | CAGE CODE LEVEL ART NO. BODY, FERRULE AND OUTER CONTACT: BRIGHT NICKEL Sires PROJECT ENG: B 66197 CTR 3 5 2 2 PER QQ-N-290 - CENTER CONTACT: GOLD PER MIL-G-45204 ne HACKETT 8/18/95|ScALE: | rus NO FAE\SPEC\CONN\INST\CTRI522 | suet: 1 oF 4