HCPL-7723/0723 50 MBd 2 ns PWD High Speed CMOS Optocoupler Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxE denotes a lead-free product Description Features Available in either 8-pin DIP or SO8 package style respectively, the HCPL-7723 or HCPL-0723 optocoupler utilize the latest CMOS IC technology to achieve outstanding speed performance of minimum 50 MBd data rate and 2 ns maximum pulse width distortion. * * * * * * * * Basic building blocks of HCPL-7723/0723 are a CMOS LED driver IC, a high speed LED and a CMOS detector IC. A CMOS logic input signal controls the LED driver IC, which supplies current to the LED. The detector IC incorporates an integrated photodiode, a high speed transimpedance amplifier, and a voltage comparator with an output driver. Functional Diagram **VDD1 1 8 VDD2** VI 2 7 NC* 6 VO 5 GND2 NC* 3 GND1 4 IO LED1 SHIELD * PIN 3 IS THE ANODE OF THE INTERNAL LED AND MUST BE LEFT UNCONNECTED FOR GUARANTEED DATASHEET PERFORMANCE. PIN 7 IS NOT CONNECTED INTERNALLY. ** A 0.1 F BYPASS CAPACITOR MUST BE CONNECTED BETWEEN PINS 1 AND 4, AND 5 AND 8. +5 V CMOS compatibility High speed: 50 MBd min. 2 ns max. pulse width distortion 22 ns max. prop. delay 16 ns max. prop. delay skew 10 kV/s min. common mode rejection -40 to 85C temperature range Safety and regulatory approvals: UL recognized - 5000 Vrms for 1 min. per UL1577 for HCPL-7723 for option 020 - 3750 Vrms for 1 min. per UL1577 for HCPL-0723 CSA component acceptance notice #5 IEC/EN/DIN EN 60747-5-2 - Viorm = 630 Vpeak for HCPL-7723 option 060 - Viorm = 560 Vpeak for HCPL-0723 option 060 Applications * Digital fieldbus isolation: CC-Link, DeviceNet, Profibus, SDS, Isolated A/D or D/A conversion * Multiplexed data transmission * High speed digital input/output * Computer peripheral interface * Microprocessor system interface TRUTH TABLE (POSITIVE LOGIC) VI, INPUT LED1 VO, OUTPUT H L OFF ON H L CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation, which may be induced by ESD. Package Outline Drawings HCPL-7723 8-Pin DIP Package 9.65 0.25 (0.380 0.010) TYPE NUMBER 8 7 6 7.62 0.25 (0.300 0.010) 5 OPTION 060 CODE* 6.35 0.25 (0.250 0.010) DATE CODE A XXXXV YYWW 1 1.19 (0.047) MAX. 2 3 4 1.78 (0.070) MAX. 5 TYP. 3.56 0.13 (0.140 0.005) 4.70 (0.185) MAX. + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002) 0.51 (0.020) MIN. 2.92 (0.115) MIN. 1.080 0.320 (0.043 0.013) 0.65 (0.025) MAX. 2.54 0.25 (0.100 0.010) DIMENSIONS IN MILLIMETERS AND (INCHES). *OPTION 300 AND 500 NOT MARKED. NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX. HCPL-7723 Package with Gull Wing Surface Mount Option 300 LAND PATTERN RECOMMENDATION 9.65 0.25 (0.380 0.010) 6 7 8 1.016 (0.040) 5 6.350 0.25 (0.250 0.010) 1 3 2 10.9 (0.430) 4 2.0 (0.080) 1.27 (0.050) 9.65 0.25 (0.380 0.010) 1.780 (0.070) MAX. 1.19 (0.047) MAX. 7.62 0.25 (0.300 0.010) 3.56 0.13 (0.140 0.005) 1.080 0.320 (0.043 0.013) 0.635 0.25 (0.025 0.010) 0.635 0.130 2.54 (0.025 0.005) (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002) 12 NOM. NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX. HCPL-0723 Small Outline SO-8 Package LAND PATTERN RECOMMENDATION 8 7 6 5 XXXV YWW 3.937 0.127 (0.155 0.005) 5.994 0.203 (0.236 0.008) TYPE NUMBER (LAST 3 DIGITS) 7.49 (0.295) DATE CODE PIN ONE 1 2 3 4 0.406 0.076 (0.016 0.003) 1.9 (0.075) 1.270 BSC (0.050) 0.64 (0.025) * 5.080 0.127 (0.200 0.005) 3.175 0.127 (0.125 0.005) 7 1.524 (0.060) 45 X 0.432 (0.017) 0 ~ 7 0.228 0.025 (0.009 0.001) 0.203 0.102 (0.008 0.004) * TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) 5.207 0.254 (0.205 0.010) 0.305 MIN. (0.012) DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX. OPTION NUMBER 500 NOT MARKED. NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX. Device Selection Guide 8-Pin DIP (300 mil) Small Outline SO-8 HCPL-7723 HCPL-0723 Ordering Information HCPL-0723 and HCPL-7723 are UL Recognized with 3750 Vrms for 1 minute per UL1577. Option Part RoHS non RoHS Surface Gull Tape UL 5000 Vrms/ IEC/EN/DIN Number Compliant Compliant Package Mount Wing & Reel 1 Minute rating EN 60747-5-2 -000E no option 300 mil DIP-8 -300E -300 X X -500E -500 X X X -020E -020 X HCPL-7723 -320E -320 X X X -520E -520 X X X X -060E -060 X -360E -360 X X X -560E -560 X X X X -000E no option SO-8 X HCPL-0723 -500E -500 X X -060E -060 X X -560E -560 X X X Quantity 50 per tube 50 per tube 1000 per reel 50 per tube 50 per tube 1000 per reel 50 per tube 50 per tube 1000 per reel 100 per tube 1500 per reel 100 per tube 1500 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: HCPL-7723-560E to order product of Gull Wing Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-2 Safety Approval and RoHS compliant. Example 2: HCPL-0723 to order product of Small Outline SO-8 package in Tube packaging and non RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. Remarks: The notation `#XXX' is used for existing products, while (new) products launched since July 15, 2001 and RoHS compliant will use `-XXXE.' Solder Reflow Temperature Profile Regulatory Information The HCPL-7723/0723 have been approved by the following organizations: 300 TEMPERATURE (C) PREHEATING RATE 3C + 1C/-0.5C/SEC. REFLOW HEATING RATE 2.5C 0.5C/SEC. 200 PEAK TEMP. 245C PEAK TEMP. 240C 2.5C 0.5C/SEC. UL Recognized under UL1577, component recognition program, File E55361. SOLDERING TIME 200C 30 SEC. 160C 150C 140C PEAK TEMP. 230C 30 SEC. 3C + 1C/-0.5C 100 PREHEATING TIME 150C, 90 + 30 SEC. 50 SEC. TIGHT TYPICAL LOOSE ROOM TEMPERATURE 0 0 50 100 150 200 250 TIME (SECONDS) Note: Non-halide flux should be used. Recommended Pb-Free IR Profile TEMPERATURE TL Tsmax IEC/EN/DIN EN 60747-5-2 Approved under: IEC 60747-5-2:1997+A1:2002/ EN 60747-5-2:2001+A1:2002/ DIN EN 60747-5-2 (VDE 0884 Teil 2): 2003-01. (Option 060 only) TIME WITHIN 5 C of ACTUAL PEAK TEMPERATURE tp Tp CSA Approved under CSA Component Acceptance Notice #5, File CA88324. 20-40 SEC. 260 +0/-5 C 217 C RAMP-UP 3 C/SEC. MAX. 150 - 200 C RAMP-DOWN 6 C/SEC. MAX. Tsmin ts PREHEAT 60 to 180 SEC. 25 tL 60 to 150 SEC. t 25 C to PEAK TIME NOTES: THE TIME FROM 25 C to PEAK TEMPERATURE = 8 MINUTES MAX. Tsmax = 200 C, Tsmin = 150 C Note: Non-halide flux should be used. Insulation and Safety Related Specifications Parameter Symbol Value 7723 0723 Units Conditions Minimum External Air Gap L(I01) 7.1 4.9 mm (Clearance) Measured from input terminals to output terminals, shortest distance through air. Minimum External Tracking L(I02) 7.4 4.8 mm (Creepage) Measured from input terminals to output terminals, shortest distance path along body. Minimum Internal Plastic Gap 0.08 0.08 mm (Internal Clearance) Insulation thickness between emitter and detector; also known as distance through insulation. Tracking Resistance (Comparative Tracking Index) DIN IEC 112/VDE 0303 Part 1 CTI Isolation Group 175 175 Volts IIIa IIIa Material Group (DIN VDE 0110, 1/89, Table 1) All Avago data sheets report the creepage and clearance inherent to the optocoupler component itself. These dimensions are needed as a starting point for the equipment designer when determining the circuit insulation requirements. However, once mounted on a printed circuit board, minimum creepage and clearance requirements must be met as specified for individual equipment standards. For creepage, the shortest distance path along the surface of a printed circuit board between the solder fillets of the input and output leads must be considered. There are recommended techniques such as grooves and ribs, which may be used on a printed circuit board to achieve desired creepage and clearances. Creepage and clearance distances will also change depending on factors such as pollution degree and insulation level. IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (Option 060) Description Symbol HCPL-7723 Option 060 HCPL-0723 Option 060 Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage 150 V rms for rated mains voltage 300 V rms for rated mains voltage 450 V rms I-IV I-IV I-III I-IV I-III Climatic Classification 55/85/21 55/85/21 Pollution Degree (DIN VDE 0110/1.89) 2 2 Maximum Working Insulation Voltage VIORM 630 560 V peak Input to Output Test Voltage, Method b* VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, Partial Discharge < 5 pC VPR 1181 1050 V peak Input to Output Test Voltage, Method a* VIORM x 1.5 = VPR, Type and Sample Test, tm = 60 sec, Partial Discharge < 5 pC VPR 945 840 V peak Highest Allowable Overvoltage* (Transient Overvoltage, tini = 10 sec) VIOTM 6000 4000 V peak Safety Limiting Values (maximum values allowed in the event of a failure, also see Thermal Derating curve, Figure 11) Case Temperature Input Current Output Power TS IS,INPUT PS,OUTPUT 175 230 600 150 150 600 C mA mW Insulation Resistance at TS, VIO = 500 V RIO 109 109 Units *Refer to the front of the optocoupler section of the Isolation and Control Component Designer's Catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-2, for a detailed description. Note: These optocouplers are suitable for "safe electrical isolation" only within the safety limit data. Maintenance of the safety data shall be ensured by means of protective circuits. Note: The surface mount classification is Class A in accordance with CECC 00802. Absolute Maximum Ratings Parameter Symbol Min. Max. Units Storage Temperature TS -55 125 C Ambient Operating Temperature[1] TA -40 85 C Supply Voltages VDD1, VDD2 0 6.0 Volts Input Voltage VI -0.5 VDD1 +0.5 Volts Output Voltage VO -0.5 VDD2 +0.5 Volts Average Output Current IO 10 mA Lead Solder Temperature 260C for 10 sec., 1.6 mm below seating plane Solder Reflow Temperature Profile See Solder Reflow Temperature Profile Section Recommended Operating Conditions Parameter Symbol Min. Max. Units Ambient Operating Temperature TA -40 85 C Supply Voltages VDD1, VDD2 4.5 5.5 V Logic High Input Voltage VIH 2.0 VDD1 V Logic Low Input Voltage VIL 0.0 0.8 V Input Signal Rise and Fall Times tr, tf 1.0 ms Electrical Specifications Test conditions that are not specified can be anywhere within the recommended operating range. All typical specifications are at TA = +25C, VDD1 = VDD2 = +5 V. Parameter Symbol Logic Low Input Supply Current[2] Min. Typ. Max. Units Test Conditions IDD1L 7 10 mA VI = 0 V Logic High Input Supply Current[2] IDD1H 1.8 3 mA VI = VDD1 Output Supply Current IDD2L 12.5 17.5 mA IDD2H 12 16.5 mA 10 A Input Current II -10 Logic High Output Voltage VOH 4.4 5.0 V IO = -20 A, VI = VIH 4.0 4.8 V IO = -4 mA, VI = VIH 0 0.1 V IO = 20 A, VI = VIL 0.5 1.0 V IO = 4 mA, VI = VIL Logic Low Output Voltage VOL Switching Specifications Test conditions that are not specified can be anywhere within the recommended operating range. All typical specifications are at TA = +25C, VDD1 = VDD2 = +5 V. Parameter Symbol Propagation Delay Time to Logic Low Output[3] Typ. Max. Units Test Conditions tPHL 16 22 ns CL = 15 pF CMOS Signal Levels Propagation Delay Time to Logic High Output[3] tPLH 16 22 ns CL = 15 pF CMOS Signal Levels Pulse Width PW 20 ns CL = 15 pF CMOS Signal Levels 50 MBd CL = 15 pF CMOS Signal Levels 2 ns CL = 15 pF CMOS Signal Levels 16 ns CL = 15 pF CMOS Signal Levels Maximum Data Rate Min. Pulse Width Distortion[4] |tPHL - tPLH| |PWD| Propagation Delay Skew[5] tPSK Output Rise Time (10% - 90%) tR 8 ns CL = 15 pF CMOS Signal Levels Output Fall Time (90% - 10%) tF 6 ns CL = 15 pF CMOS Signal Levels 1 Common Mode Transient Immunity |CMH| 10 15 kV/s at Logic High Output[6] VCM = 1000 V, TA = 25C, VI = VDD1, VO > 0.8 VDD2 Common Mode Transient Immunity |CML| 10 15 kV/s at Logic Low Output[6] VCM = 1000 V, TA = 25C, VI = 0 V, VO < 0.8 V Package Characteristics All Typical Specifications are at TA = 25C. Parameter Input-Output Momentary Withstand Voltage[7,8,9] Symbol -7723 VISO Option 020 -0723 Min. Typ. Max. Units Test Conditions 3750 V rms RH 50%, t = 1 min, 5000 TA = 25C 3750 Input-Output Resistance[7] R I-O 10 12 VI-O = 500 V dc Input-Output Capacitance C I-O 0.6 pF f = 1 MHz Input Capacitance[10] C I 3.0 pF Input IC Junction-to-Case Thermal Resistance -7723 jci -0723 145 C/W Thermocouple located at 160center underside of package Output IC Junction-to-Case Thermal Resistance -7723 jco -0723 145 C/W 135 Package Power Dissipation PPD 150 mW Notes: 1. Absolute Maximum ambient operating temperature means the device will not be damaged if operated under these conditions. It does not guarantee functionality. 2. The LED is ON when VI is low and OFF when VI is high. 3. tPHL propagation delay is measured from the 50% level on the falling edge of the VI signal to the 50% level of the falling edge of the VO signal. tPLH propagation delay is measured from the 50% level on the rising edge of the VI signal to the 50% level of the rising edge of the VO signal. 4. PWD is defined as |tPHL - tPLH|. %PWD (percent pulse width distortion) is equal to the PWD divided by pulse width. 5. tPSK is equal to the magnitude of the worst case difference in tPHL and/or tPLH that will be seen between units at any given temperature within the recommended operating conditions. 6. CMH is the maximum common mode voltage slew rate that can be sustained while maintaining VO > 0.8 VDD2. CML is the maximum common mode voltage slew rate that can be sustained while maintaining VO < 0.8 V. The common mode voltage slew rates apply to both rising and falling common mode voltage edges. 7. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together. 8. In accordance with UL1577, each HCPL-0723 is proof tested by applying an insulation test voltage 4500 Vrms for 1 second (leakage detection current limit, II-O 5 A). Each HCPL-7723 is proof tested by applying an insulation test voltage 4500 Vrms for 1 second (leakage detection current limit. II-O 5 A.) 9. The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to your equipment level safety specification or Avago Application Note 1074 entitled "Optocoupler Input-Output Endurance Voltage." 10. CI is the capacitance measured at pin 2 (VI). Application Information Propagation Delay, Pulse-Width Distortion and Propagation Delay Skew Bypassing and PC Board Layout The HCPL-7723/0723 optocouplers are extremely easy to use. No external interface circuitry is required because the HCPL-7723/0723 use high-speed CMOS IC technology allowing CMOS logic to be connected directly to the inputs and outputs. As shown in Figure 1, the only external components required for proper operation are two bypass capacitors. Capacitor values should be between 0.01 F and 0.1 F. For each capacitor, the total lead length between both ends of the capacitor and the power-supply pins should not exceed 20 mm. Figure 2 illustrates the recommended printed circuit board layout for the HCPL-7723/0723. VDD1 VDD2 8 1 Propagation Delay is a figure of merit which describes how quickly a logic signal propagates through a system as illustrated in Figure 3. The propagation delay from low to high (tPLH) is the amount of time required for an input signal to propagate to the output, causing the output to change from low to high. Similarly, the propagation delay from high to low (tPHL) is the amount of time required for the input signal to propagate to the output, causing the output to change from high to low. C1 C2 VI 720 YWW 2 NC 3 GND1 7 NC 6 VO 5 4 GND2 C1, C2 = 0.01 F TO 0.1 F Figure 1. Functional diagram. VDD1 VDD2 720 YWW VI C1 C2 VO GND1 GND2 C1, C2 = 0.01 F TO 0.1 F Figure 2. Recommended printed circuit board layout. INPUT VI 5 V CMOS 50% tPLH OUTPUT VO 90% 90% 10% Figure 3. Timing diagram to illustrate propagation delay, tplh and tphl. 10 0V tPHL 10% VOH 2.5 V CMOS VOL Pulse-width distortion (PWD) is the difference between tPHL and tPLH and often determines the maximum data rate capability of a transmission system. PWD can be expressed in percent by dividing the PWD (in ns) by the minimum pulse width (in ns) being transmitted. Typically, PWD on the order of 20-30% of the minimum pulse width is tolerable. Propagation delay skew, tPSK, is an important parameter to consider in parallel data applications where synchronization of signals on parallel data lines is a concern. If the parallel data is being sent through a group of optocouplers, differences in propagation delays will cause the data to arrive at the outputs of the optocouplers at different times. If this difference in propagation delay is large enough it will determine the maximum rate at which parallel data can be sent through the optocouplers. Propagation delay skew is defined as the difference between the minimum and maximum propagation delays, either tPLH or tPHL, for any given group of optocouplers which are operating under the same conditions (i.e., the same drive current, supply voltage, output load, and operating temperature). As illustrated in Figure 4, if the inputs of a group of optocouplers are switched either ON or OFF at the same time, tPSK is the difference between the shortest propagation delay, either tPLH or tPHL, and the longest propagation delay, either tPLH or tPHL. VI As mentioned earlier, tPSK can determine the maximum parallel data transmission rate. Figure 5 is the timing diagram of a typical parallel data application with both the clock and data lines being sent through the optocouplers. The figure shows data and clock signals at the inputs and outputs of the optocouplers. In this case the data is assumed to be clocked off of the rising edge of the clock. Propagation delay skew represents the uncertainty of where an edge might be after being sent through an optocoupler. Figure 5 shows that there will be uncertainty in both the data and clock lines. It is important that these two areas of uncertainty not overlap, otherwise the clock signal might arrive before all of the data outputs have settled, or some of the data outputs may start to change before the clock signal has arrived. From these considerations, the absolute minimum pulse width that can be sent through optocouplers in a parallel application is twice tPSK. A cautious design should use a slightly longer pulse width to ensure that any additional uncertainty in the rest of the circuit does not cause a problem. The HCPL-7723/0723 optocouplers offer the advantage of guaranteed specifications for propagation delays, pulsewidth distortion, and propagation delay skew over the recommended temperature and power supply ranges. DATA 50% INPUTS VO 2.5 V, CMOS CLOCK tPSK VI 50% DATA OUTPUTS VO 2.5 V, CMOS tPSK CLOCK tPSK Figure 4. Timing diagram to illustrate propagation delay skew, tpsk. Figure 5. Parallel data transmission example. For product information and a complete list of distributors, please go to our website: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries. Data subject to change. Copyright (c) 2007 Avago Technologies Limited. All rights reserved. Obsoletes AV01-0566EN AV02-0643EN - November 26, 2007