ADC0820
ADC0820 8-Bit High Speed µP Compatible A/D Converter with Track/Hold
Function
Literature Number: SNAS529B
ADC0820
8-Bit High Speed µP Compatible A/D Converter with
Track/Hold Function
General Description
By using a half-flash conversion technique, the 8-bit
ADC0820 CMOS A/D offers a 1.5 µs conversion time and
dissipates only 75 mW of power. The half-flash technique
consists of 32 comparators, a most significant 4-bit ADC and
a least significant 4-bit ADC.
The input to the ADC0820 is tracked and held by the input
sampling circuitry eliminating the need for an external
sample-and-hold for signals moving at less than 100 mV/µs.
For ease of interface to microprocessors, the ADC0820 has
been designed to appear as a memory location or I/O port
without the need for external interfacing logic.
Key Specifications
jResolution 8 Bits
jConversion Time 2.5 µs Max (RD Mode)
1.5 µs Max (WR-RD Mode)
jLow Power 75 mW Max
jTotal Unadjusted
Error ±
1
2
LSB and ±1 LSB
Features
nBuilt-in track-and-hold function
nNo missing codes
nNo external clocking
nSingle supply 5 V
DC
nEasy interface to all microprocessors, or operates
stand-alone
nLatched TRI-STATE output
nLogic inputs and outputs meet both MOS and T
2
L
voltage level specifications
nOperates ratiometrically or with any reference value
equal to or less than V
CC
n0V to 5V analog input voltage range with single 5V
supply
nNo zero or full-scale adjust required
nOverflow output available for cascading
n0.3" standard width 20-pin DIP
n20-pin molded chip carrier package
n20-pin small outline package
n20-pin shrink small outline package (SSOP)
Connection and Functional Diagrams
Dual-In-Line, Small Outline
and SSOP Packages
Molded Chip Carrier
Package
00550101
Top View
00550133
March 2004
ADC0820 8-Bit High Speed µP Compatible A/D Converter with Track/Hold Function
© 2004 National Semiconductor Corporation DS005501 www.national.com
Connection and Functional Diagrams (Continued)
Ordering Information
Part Number Total Package Temperature
Unadjusted Error Range
ADC0820BCV V20A Molded Chip Carrier 0˚C to +70˚C
ADC0820BCWM ±
1
2
LSB M20B Wide Body Small Outline 0˚C to +70˚C
ADC0820BCN N20A Molded DIP 0˚C to +70˚C
ADC0820CCJ
±1 LSB
J20A Cerdip −40˚C to +85˚C
ADC0820CCWM M20B Wide Body Small Outline 0˚C to +70˚C
ADC0820CIWM M20B Wide Body Small Outline −40˚C to +85˚C
ADC0820CCN N20A Molded DIP 0˚C to +70˚C
00550102
FIGURE 1.
ADC0820
www.national.com 2
Absolute Maximum Ratings (Notes 1, 2)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage (V
CC
) 10V
Logic Control Inputs −0.2V to V
CC
+0.2V
Voltage at Other Inputs and Output −0.2V to V
CC
+0.2V
Storage Temperature Range −65˚C to +150˚C
Package Dissipation at T
A
= 25˚C 875 mW
Input Current at Any Pin (Note 5) 1 mA
Package Input Current (Note 5) 4 mA
ESD Susceptability (Note 9) 900V
Lead Temp. (Soldering, 10 sec.)
Dual-In-Line Package (plastic) 260˚C
Dual-In-Line Package (ceramic) 300˚C
Surface Mount Package
Vapor Phase (60 sec.) 215˚C
Infrared (15 sec.) 220˚C
Operating Ratings (Notes 1, 2)
Temperature Range T
MIN
T
A
T
MAX
ADC0820CCJ −40˚CT
A
+85˚C
ADC0820CIWM −40˚CT
A
+85˚C
ADC0820BCN, ADC0820CCN 0˚CT
A
70˚C
ADC0820BCV 0˚CT
A
70˚C
ADC0820BCWM, ADC0820CCWM 0˚CT
A
70˚C
V
CC
Range 4.5V to 8V
Converter Characteristics
The following specifications apply for RD mode (pin 7=0), V
CC
=5V, V
REF
(+)=5V,and V
REF
(−)=GND unless otherwise specified.
Boldface limits apply from T
MIN
to T
MAX
; all other limits T
A
=T
j
=25˚C.
Parameter Conditions ADC0820BCN, ADC0820CCN Limit
Units
ADC0820CCJ ADC0820BCV, ADC0820BCWM
ADC0820CCWM, ADC0820CIWM
Typ Tested Design Typ Tested Design
(Note 6) Limit Limit (Note 6) Limit Limit
(Note 7) (Note 8) (Note 7) (Note 8)
Resolution 888Bits
Total Unadjusted ADC0820BCN, BCWM ±
1
2
±
1
2
LSB
Error ADC0820CCJ ±1LSB
(Note 3) ADC0820CCN, CCWM, CIWM ±1±1LSB
ADC0820CCMSA ±1±1LSB
Minimum Reference 2.3 1.00 2.3 1.2 k
Resistance
Maximum
Reference
2.3 62.3 5.3 6k
Resistance
Maximum V
REF
(+) V
CC
V
CC
V
CC
V
Input Voltage
Minimum V
REF
(−) GND GND GND V
Input Voltage
Minimum V
REF
(+) V
REF
(−) V
REF
(−) V
REF
(−) V
Input Voltage
Maximum V
REF
(−) V
REF
(+) V
REF
(+) V
REF
(+) V
Input Voltage
Maximum V
IN
Input V
CC
+0.1 V
CC
+0.1 V
CC
+0.1 V
Voltage
Minimum V
IN
Input GND−0.1 GND−0.1 GND−0.1 V
Voltage
Maximum Analog CS =V
CC
Input Leakage V
IN
=V
CC
30.3 3µA
Current V
IN
=GND −3 −0.3 −3 µA
Power Supply
Sensitivity
V
CC
=5V±5% ±1/16 ±
1
4
±1/16 ±
1
4
±
1
4
LSB
ADC0820
www.national.com3
DC Electrical Characteristics
The following specifications apply for V
CC
=5V, unless otherwise specified. Boldface limits apply from T
MIN
to T
MAX
; all other
limits T
A
=T
J
=25˚C.
Parameter Conditions ADC0820BCN, ADC0820CCN Limit
Units
ADC0820CCJ ADC0820BCV, ADC0820BCWM
ADC0820CCWM, ADC0820CIWM
Typ Tested Design Typ Tested Design
(Note 6) Limit Limit (Note 6) Limit Limit
(Note 7) (Note 8) (Note 7) (Note 8)
V
IN(1)
, Logical “1” V
CC
=5.25V CS , WR , RD 2.0 2.0 2.0 V
Input Voltage Mode 3.5 3.5 3.5 V
V
IN(0)
, Logical “0” V
CC
=4.75V CS , WR , RD 0.8 0.8 0.8 V
Input Voltage Mode 1.5 1.5 1.5 V
I
IN(1)
, Logical “1” V
IN(1)
=5V; CS , RD 0.005 10.005 1µA
Input Current V
IN(1)
=5V; WR 0.1 30.1 0.3 3µA
V
IN(1)
=5V; Mode 50 200 50 170 200 µA
I
IN(0)
, Logical “0” V
IN(0)
=0V; CS , RD , WR , −0.005 −1 −0.005 −1 µA
Input Current Mode
V
OUT(1)
, Logical “1” V
CC
=4.75V, I
OUT
=−360 µA; 2.4 2.8 2.4 V
Output Voltage DB0DB7, OFL , INT
V
CC
=4.75V, I
OUT
=−10 µA; 4.5 4.6 4.5 V
DB0–DB7, OFL , INT
V
OUT(0)
, Logical “0” V
CC
=4.75V, I
OUT
=1.6 mA; 0.4 0.34 0.4 V
Output Voltage DB0DB7, OFL , INT , RDY
I
OUT
, TRI-STATE V
OUT
=5V; DB0–DB7, RDY 0.1 30.1 0.3 3µA
Output Current V
OUT
=0V; DB0–DB7, RDY −0.1 −3 −0.1 −0.3 −3 µA
I
SOURCE
, Output V
OUT
=0V; DB0–DB7, OFL −12 −6 −12 −7.2 −6 mA
Source Current INT −9 −4.0 −9 −5.3 −4.0 mA
I
SINK
, Output Sink V
OUT
=5V; DB0–DB7, OFL , 14 714 8.4 7mA
Current INT , RDY
I
CC
, Supply Current CS =WR =RD =0 7.5 15 7.5 13 15 mA
AC Electrical Characteristics
The following specifications apply for V
CC
=5V, t
r
=t
f
=20 ns, V
REF
(+)=5V, V
REF
(−)=0V and T
A
=25˚C unless otherwise specified.
Typ Tested Design
Parameter Conditions (Note 6) Limit Limit Units
(Note 7) (Note 8)
t
CRD
, Conversion Time for RD Mode Pin7=0,Figure 2 1.6 2.5 µs
t
ACC0
, Access Time (Delay from Pin7=0,Figure 2 t
CRD
+20 t
CRD
+50 ns
Falling Edge of RD to Output Valid)
t
CWR-RD
, Conversion Time for Pin7=V
CC
;t
WR
= 600 ns, 1.52 µs
WR-RD Mode t
RD
=600 ns; Figures 3, 4
t
WR
, Write Time Min Pin7=V
CC
;Figures 3, 4 600 ns
Max (Note 4) See Graph 50 µs
t
RD
, Read Time Min Pin7=V
CC
;Figures 3, 4 600 ns
(Note 4) See Graph
t
ACC1
, Access Time (Delay from Pin7=V
CC
,t
RD
<t
I
;Figure 3
Falling Edge of RD to Output Valid) C
L
=15 pF 190 280 ns
C
L
=100 pF 210 320 ns
ADC0820
www.national.com 4
AC Electrical Characteristics (Continued)
The following specifications apply for V
CC
=5V, t
r
=t
f
=20 ns, V
REF
(+)=5V, V
REF
(−)=0V and T
A
=25˚C unless otherwise specified.
Typ Tested Design
Parameter Conditions (Note 6) Limit Limit Units
(Note 7) (Note 8)
t
ACC2
, Access Time (Delay from
Falling Edge of RD to Output Valid)
Pin7=V
CC
,t
RD
>t
I
;Figure 4
C
L
=15 pF 70 120 ns
C
L
=100 pF 90 150 ns
t
ACC3
, Access Time (Delay from
Rising Edge of RDY to Output
Valid)
R
PULLUP
= 1k and C
L
=15pF 30 ns
t
I
, Internal Comparison Time Pin 7=V
CC
;Figures 4, 5 800 1300 ns
C
L
=50 pF
t
1H
,t
0H
, TRI-STATE Control R
L
=1k, C
L
=10 pF 100 200 ns
(Delay from Rising Edge of RD to
Hi-Z State)
t
INTL
, Delay from Rising Edge of Pin7=V
CC
,C
L
=50pF
WR to Falling Edge of INT t
RD
>t
I
;Figure 4 t
I
ns
t
RD
<t
I
;Figure 3 t
RD
+200 t
RD
+290 ns
t
INTH
, Delay from Rising Edge of Figures 2, 3, 4 125 225 ns
RD to Rising Edge of INT C
L
=50 pFc
t
INTHWR
, Delay from Rising Edge of Figure 5,C
L
=50 pF 175 270 ns
WR to Rising Edge of INT
t
RDY
, Delay from CS to RDY Figure 2,C
L
=50 pF, Pin 7 =0 50 100 ns
t
ID
, Delay from INT to Output Valid Figure 5 20 50 ns
t
RI
, Delay from RD to INT Pin 7=V
CC
,t
RD
<t
I
200 290 ns
Figure 3
t
P
, Delay from End of Conversion Figures 2, 3, 4, 5 500 ns
to Next Conversion (Note 4) See Graph
Slew Rate, Tracking 0.1 V/µs
C
VIN
, Analog Input Capacitance 45 pF
C
OUT
, Logic Output Capacitance 5 pF
C
IN
, Logic Input Capacitance 5 pF
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating
the device beyond its specified operating conditions.
Note 2: All voltages are measured with respect to the GND pin, unless otherwise specified.
Note 3: Total unadjusted error includes offset, full-scale, and linearity errors.
Note 4: Accuracy may degrade if tWR or tRD is shorter than the minimum value specified. See Accuracy vs. tWR and Accuracy vs. tRD graphs.
Note 5: When the input voltage (VIN) at any pin exceeds the power supply rails (VIN <Vor VIN >V+) the absolute value of current at that pin should be limited
to 1 mA or less. The 4 mA package input current limits the number of pins that can exceed the power supply boundaries witha1mAcurrent limit to four.
Note 6: Typicals are at 25˚C and represent most likely parametric norm.
Note 7: Tested limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).
Note 8: Design limits are guaranteed but not 100% tested. These limits are not used to calculate outgoing quality levels.
Note 9: Human body model, 100 pF discharged through a 1.5 kresistor.
ADC0820
www.national.com5
TRI-STATE Test Circuits and Waveforms
t
1H
00550103
00550104
tr=20 ns
t
0H
00550105
00550106
tr=20 ns
Timing Diagrams
00550107
Note: On power-up the state of INT can be high or low.
FIGURE 2. RD Mode (Pin 7 is Low)
ADC0820
www.national.com 6
Timing Diagrams (Continued)
00550108
FIGURE 3. WR-RD Mode (Pin 7 is High and t
RD
<t
I
)
00550109
FIGURE 4. WR-RD Mode (Pin 7 is High and t
RD
>t
I
)
00550110
FIGURE 5. WR-RD Mode (Pin 7 is High)
Stand-Alone Operation
ADC0820
www.national.com7
Typical Performance Characteristics
Logic Input Threshold Voltage vs. Supply Voltage Conversion Time (RD Mode) vs. Temperature
00550134 00550135
Power Supply Current vs. Temperature
(not including reference ladder) Accuracy vs. t
WR
00550136 00550137
Accuracy vs. t
RD
Accuracy vs. t
p
00550138 00550139
ADC0820
www.national.com 8
Typical Performance Characteristics (Continued)
Accuracy vs. V
REF
[V
REF
=V
REF
(+)-V
REF
(-)] t
I
, Internal Time Delay vs. Temperature
00550140 00550141
Output Current vs. Temperature
00550142
ADC0820
www.national.com9
Description of Pin Functions
Pin Name Function
1V
IN
Analog input; range =GNDV
IN
V
CC
2 DB0 TRI-STATE data output bit 0 (LSB)
3 DB1 TRI-STATE data output bit 1
4 DB2 TRI-STATE data output bit 2
5 DB3 TRI-STATE data output bit 3
6WR
/RDY
WR-RD Mode
WR: With CS low, the conversion is
started on the falling edge of WR.
Approximately 800 ns (the preset internal
time out, t
I
) after the WR rising edge, the
result of the conversion will be strobed
into the output latch, provided that RD
does not occur prior to this time out (see
Figures 3, 4 ).
RD Mode
RDY: This is an open drain output (no
internal pull-up device). RDY will go low
after the falling edge of CS; RDY will go
TRI-STATE when the result of the
conversion is strobed into the output latch.
It is used to simplify the interface to a
microprocessor system (see Figure 2 ).
7 Mode Mode: Mode selection input it is
internally tied to GND through a 50 µA
current source.
RD Mode: When mode is low
WR-RD Mode: When mode is high
8RD WR-RD Mode
With CS low, the TRI-STATE data outputs
(DB0-DB7) will be activated when RD
goes low (see Figure 5 ). RD can also be
used to increase the speed of the
converter by reading data prior to the
preset internal time out (t
I
,800 ns). If this
is done, the data result transferred to
output latch is latched after the falling
edge of the RD (see Figures 3, 4 ).
RD Mode
With CS low, the conversion will start with
RD going low, also RD will enable the
TRI-STATE data outputs at the completion
of the conversion. RDY going TRI-STATE
and INT going low indicates the
completion of the conversion (see Figure
2).
Pin Name Function
9 INT WR-RD Mode
INT going low indicates that the
conversion is completed and the data
result is in the output latch. INT will go
low, 800 ns (the preset internal time out,
t
I
) after the rising edge of WR (see Figure
4); or INT will go low after the falling
edge of RD , if RD goes low prior to the
800 ns time out (see Figure 3). INT is
reset by the rising edge of RD or CS (see
Figures 3, 4 ).
RD Mode
INT going low indicates that the
conversion is completed and the data
result is in the output latch. INT is reset by
the rising edge of RD or CS (see Figure
2).
10 GND Ground
11 V
REF
(−) The bottom of resistor ladder, voltage
range: GNDV
REF
(−)V
REF
(+) (Note 5)
12 V
REF
(+) The top of resistor ladder, voltage range:
V
REF
(−)V
REF
(+)V
CC
(Note 5)
13 CS CS must be low in order for the RD or
WR to be recognized by the converter.
14 DB4 TRI-STATE data outputbit 4
15 DB5 TRI-STATE data outputbit 5
16 DB6 TRI-STATE data outputbit 6
17 DB7 TRI-STATE data outputbit 7 (MSB)
18 OFL Overflow output If the analog input is
higher than the V
REF
(+), OFL will be low
at the end of conversion. It can be used to
cascade 2 or more devices to have more
resolution (9, 10-bit). This output is always
active and does not go into TRI-STATE as
DB0–DB7 do.
19 NC No connection
20 V
CC
Power supply voltage
1.0 Functional Description
1.1 GENERAL OPERATION
The ADC0820 uses two 4-bit flash A/D converters to make
an 8-bit measurement (Figure 1 ). Each flash ADC is made
up of 15 comparators which compare the unknown input to a
reference ladder to get a 4-bit result. To take a full 8-bit
reading, one flash conversion is done to provide the 4 most
significant data bits (via the MS flash ADC). Driven by the 4
MSBs, an internal DAC recreates an analog approximation
of the input voltage. This analog signal is then subtracted
from the input, and the difference voltage is converted by a
second 4-bit flash ADC (the LS ADC), providing the 4 least
significant bits of the output data word.
The internal DAC is actually a subsection of the MS flash
converter. This is accomplished by using the same resistor
ladder for the A/D as well as for generating the DAC signal.
The DAC output is actually the tap on the resistor ladder
ADC0820
www.national.com 10
1.0 Functional Description (Continued)
which most closely approximates the analog input. In addi-
tion, the “sampled-data” comparators used in the ADC0820
provide the ability to compare the magnitudes of several
analog signals simultaneously, without using input summing
amplifiers. This is especially useful in the LS flash ADC,
where the signal to be converted is an analog difference.
1.2 THE SAMPLED-DATA COMPARATOR
Each comparator in the ADC0820 consists of a CMOS in-
verter with a capacitively coupled input (Figures 6, 7 ). Ana-
log switches connect the two comparator inputs to the input
capacitor (C) and also connect the inverter’s input and out-
put. This device in effect now has one differential input pair.
A comparison requires two cycles, one for zeroing the com-
parator, and another for making the comparison.
In the first cycle, one input switch and the inverter’s feedback
switch (Figure 6 ) are closed. In this interval, C is charged to
the connected input (V1) less the inverter’s bias voltage (V
B
,
approximately 1.2V). In the second cycle (Figure 7 ), these
two switches are opened and the other (V2) input’s switch is
closed. The input capacitor now subtracts its stored voltage
from the second input and the difference is amplified by the
inverter’s open loop gain. The inverter’s input (V
B
') becomes
and the output will go high or low depending on the sign of
V
B
'−V
B
.
The actual circuitry used in the ADC0820 is a simple but
important expansion of the basic comparator described
above. By adding a second capacitor and another set of
switches to the input (Figure 8 ), the scheme can be ex-
panded to make dual differential comparisons. In this circuit,
the feedback switch and one input switch on each capacitor
(Z switches) are closed in the zeroing cycle. A comparison is
then made by connecting the second input on each capacitor
and opening all of the other switches (S switches). The
change in voltage at the inverter’s input, as a result of the
change in charge on each input capacitor, will now depend
on both input signal differences.
1.3 ARCHITECTURE
In the ADC0820, one bank of 15 comparators is used in each
4-bit flash A/D converter (Figure 12 ). The MS (most signifi-
cant) flash ADC also has one additional comparator to detect
input overrange. These two sets of comparators operate
alternately, with one group in its zeroing cycle while the other
is comparing.
When a typical conversion is started, the WR line is brought
low. At this instant the MS comparators go from zeroing to
00550112
VO=V
B
V on C = V1−VB
CS= stray input node capacitor
VB= inverter input bias voltage
Zeroing Phase
FIGURE 6. Sampled-Data Comparator
00550113
Compare Phase
FIGURE 7. Sampled-Data Comparator
00550114
00550145
FIGURE 8. ADC0820 Comparator (from MS Flash ADC)
ADC0820
www.national.com11
1.0 Functional Description (Continued)
comparison mode (Figure 11 ). When WR is returned high
after at least 600 ns, the output from the first set of compara-
tors (the first flash) is decoded and latched. At this point the
two 4-bit converters change modes and the LS (least signifi-
cant) flash ADC enters its compare cycle. No less than 600
ns later, the RD line may be pulled low to latch the lower 4
data bits and finish the 8-bit conversion. When RD goes low,
the flash A/Ds change state once again in preparation for the
next conversion.
Figure 11 also outlines how the converter’s interface timing
relates to its analog input (V
IN
). In WR-RD mode, V
IN
is
measured while WR is low. In RD mode, sampling occurs
during the first 800 ns of RD. Because of the input connec-
tions to the ADC0820’s LS and MS comparators, the con-
verter has the ability to sample V
IN
at one instant (Section
2.4), despite the fact that two separate 4-bit conversions are
being done. More specifically, when WR is low the MS flash
is in compare mode (connected to V
IN
), and the LS flash is in
zero mode (also connected to V
IN
). Therefore both flash
ADCs sample V
IN
at the same time.
1.4 DIGITAL INTERFACE
The ADC0820 has two basic interface modes which are
selected by strapping the MODE pin high or low.
RD Mode
With the MODE pin grounded, the converter is set to Read
mode. In this configuration, a complete conversion is done
by pulling RD low until output data appears. An INT line is
provided which goes low at the end of the conversion as well
as a RDY output which can be used to signal a processor
that the converter is busy or can also serve as a system
Transfer Acknowledge signal.
RD Mode (Pin 7 is Low)
00550116
When in RD mode, the comparator phases are internally
triggered. At the falling edge of RD, the MS flash converter
goes from zero to compare mode and the LS ADC’s com-
parators enter their zero cycle. After 800 ns, data from the
MS flash is latched and the LS flash ADC enters compare
mode. Following another 800 ns, the lower 4 bits are recov-
ered.
WR then RD Mode
With the MODE pin tied high, the A/D will be set up for the
WR-RD mode. Here, a conversion is started with the WR
input; however, there are two options for reading the output
data which relate to interface timing. If an interrupt driven
scheme is desired, the user can wait for INT to go low before
reading the conversion result (Figure 10 ). INT will typically
go low 800 ns after WR’s rising edge. However, if a shorter
conversion time is desired, the processor need not wait for
INT and can exercise a read after only 600 ns (Figure 9 ). If
this is done, INT will immediately go low and data will appear
at the outputs.
Stand-Alone
For stand-alone operation in WR-RD mode, CS and RD can
be tied low and a conversion can be started with WR. Data
will be valid approximately 800 ns following WR’s rising
edge.
WR-RD Mode (Pin 7 is High) Stand-Alone Operation
00550119
00550117
FIGURE 9. WR-RD Mode (Pin 7 is High and t
RD
<t
I
)
00550118
FIGURE 10. WR-RD Mode (Pin 7 is High and t
RD
>t
I
)
ADC0820
www.national.com 12
1.0 Functional Description (Continued)
OTHER INTERFACE CONSIDERATIONS
In order to maintain conversion accuracy, WR has a maxi-
mum width spec of 50 µs. When the MS flash ADC’s
sampled-data comparators (Section 1.2) are in comparison
mode (WR is low), the input capacitors (C, Figure 8 ) must
hold their charge. Switch leakage and inverter bias current
can cause errors if the comparator is left in this phase for too
long.
Since the MS flash ADC enters its zeroing phase at the end
of a conversion (Section 1.3), a new conversion cannot be
started until this phase is complete. The minimum spec for
this time (t
P
,Figures 2, 3, 4, 5 ) is 500 ns.
00550120
Note: MS means most significant
LS means least significant
FIGURE 11. Operating Sequence (WR-RD Mode)
ADC0820
www.national.com13
Detailed Block Diagram
00550115
FIGURE 12.
ADC0820
www.national.com 14
2.0 Analog Considerations
2.1 REFERENCE AND INPUT
The two V
REF
inputs of the ADC0820 are fully differential and
define the zero to full-scale input range of the A to D con-
verter. This allows the designer to easily vary the span of the
analog input since this range will be equivalent to the voltage
difference between V
IN
(+) and V
IN
(−). By reducing
V
REF
(V
REF
=V
REF
(+)−V
REF
(−)) to less than 5V, the sensitivity
of the converter can be increased (i.e., if V
REF
=2V then 1
LSB=7.8 mV). The input/reference arrangement also facili-
tates ratiometric operation and in many cases the chip power
supply can be used for transducer power as well as the V
REF
source.
This reference flexibility lets the input span not only be varied
but also offset from zero. The voltage at V
REF
(−) sets the
input level which produces a digital output of all zeroes.
Though V
IN
is not itself differential, the reference design
affords nearly differential-input capability for most measure-
ment applications. Figure 13 shows some of the configura-
tions that are possible.
2.2 INPUT CURRENT
Due to the unique conversion techniques employed by the
ADC0820, the analog input behaves somewhat differently
than in conventional devices. The A/D’s sampled-data com-
parators take varying amounts of input current depending on
which cycle the conversion is in.
The equivalent input circuit of the ADC0820 is shown in
Figure 14. When a conversion starts (WR low, WR-RD
mode), all input switches close, connecting V
IN
to thirty-one
1 pF capacitors. Although the two 4-bit flash circuits are not
both in their compare cycle at the same time, V
IN
still sees all
input capacitors at once. This is because the MS flash
converter is connected to the input during its compare inter-
val and the LS flash is connected to the input during its
zeroing phase (Section 1.3). In other words, the LS ADC
uses V
IN
as its zero-phase input.
The input capacitors must charge to the input voltage
through the on resistance of the analog switches (about 5 k
to 10 k). In addition, about 12 pF of input stray capacitance
must also be charged. For large source resistances, the
analog input can be modeled as an RC network as shown in
Figure 15.AsR
S
increases, it will take longer for the input
capacitance to charge.
In RD mode, the input switches are closed for approximately
800 ns at the start of the conversion. In WR-RD mode, the
time that the switches are closed to allow this charging is the
time that WR is low. Since other factors force this time to be
at least 600 ns, input time constants of 100 ns can be
accommodated without special consideration. Typical total
input capacitance values of 45 pF allow R
S
to be 1.5 k
without lengthening WR to give V
IN
more time to settle.
External Reference 2.5V Full-Scale Power Supply as Reference Input Not Referred to GND
00550121 00550122
00550123
FIGURE 13. Analog Input Options
ADC0820
www.national.com15
2.0 Analog Considerations (Continued)
2.3 INPUT FILTERING
It should be made clear that transients in the analog input
signal, caused by charging current flowing into V
IN
, will not
degrade the A/D’s performance in most cases. In effect the
ADC0820 does not “look” at the input when these transients
occur. The comparators’ outputs are not latched while WR is
low, so at least 600 ns will be provided to charge the ADC’s
input capacitance. It is therefore not necessary to filter out
these transients by putting an external cap on the V
IN
termi-
nal.
2.4 INHERENT SAMPLE-HOLD
Another benefit of the ADC0820’s input mechanism is its
ability to measure a variety of high speed signals without the
help of an external sample-and-hold. In a conventional SAR
type converter, regardless of its speed, the input must re-
main at least
1
2
LSB stable throughout the conversion pro-
cess if full accuracy is to be maintained. Consequently, for
many high speed signals, this signal must be externally
sampled, and held stationary during the conversion.
Sampled-data comparators, by nature of their input switch-
ing, already accomplish this function to a large degree (Sec-
tion 1.2). Although the conversion time for the ADC0820 is
1.5 µs, the time through which V
IN
must be
1
2
LSB stable is
much smaller. Since the MS flash ADC uses V
IN
as its
“compare” input and the LS ADC uses V
IN
as its “zero” input,
the ADC0820 only “samples” V
IN
when WR is low (Sections
1.3 and 2.2). Even though the two flashes are not done
simultaneously, the analog signal is measured at one instant.
The value of V
IN
approximately 100 ns after the rising edge
of WR (100 ns due to internal logic prop delay) will be the
measured value.
Input signals with slew rates typically below 100 mV/µs can
be converted without error. However, because of the input
time constants, and charge injection through the opened
comparator input switches, faster signals may cause errors.
Still, the ADC0820’s loss in accuracy for a given increase in
signal slope is far less than what would be witnessed in a
conventional successive approximation device. An SAR type
converter with a conversion time as fast as 1 µs would still
not be able to measure a 5V 1 kHz sine wave without the aid
of an external sample-and-hold. The ADC0820, with no such
help, can typically measure 5V, 7 kHz waveforms.
00550124
FIGURE 14.
00550125
FIGURE 15.
ADC0820
www.national.com 16
3.0 Typical Applications
8-Bit Resolution Configuration
00550126
9-Bit Resolution Configuration
00550127
ADC0820
www.national.com17
3.0 Typical Applications (Continued)
Telecom A/D Converter
00550128
V
IN
=3 kHz max ±4V
P
No track-and-hold needed
Low power consumption
Multiple Input Channels
00550129
8-Bit 2-Quadrant Analog Multiplier
00550130
ADC0820
www.national.com 18
3.0 Typical Applications (Continued)
Fast Infinite Sample-and-Hold
00550131
ADC0820
www.national.com19
3.0 Typical Applications (Continued)
Digital Waveform Recorde
00550132
ADC0820
www.national.com 20
Physical Dimensions inches (millimeters) unless otherwise noted
Hermetic Dual-In-Line Package (J)
Order Number ADC0820CCJ
NS Package Number J20A
SO Package (M)
Order Number ADC0820BCWM, ADC0820CCWM or ADC0820CIWM
NS Package Number M20B
ADC0820
www.national.com21
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
Molded Dual-In-Line Package (N)
Order Number ADC0820BCN or ADC0820CCN
NS Package Number N20A
Molded Chip Carrier Package (V)
Order Number ADC0820BCV
NS Package Number V20A
ADC0820
www.national.com 22
Notes
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification
(CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2.
National Semiconductor
Americas Customer
Support Center
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Support Center
Email: ap.support@nsc.com
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
ADC0820 8-Bit High Speed µP Compatible A/D Converter with Track/Hold Function
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TIs terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TIs standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright ©2011, Texas Instruments Incorporated