TPD-MR-04-XXXXXXXX Features Description Compliant with the 300 pin SFF MSA TPD-MR-04-XXXXX C-band DWDM 300 pin SFF Support multi-rate from 9.953Gb/s to 11.3Gbps transponder C-band DWDM laser and PIN/APD receiver applications with reaches of up to 40km, which 100GHz channel spacing provide multi-rate from 9.95Gbps to 11.3Gbps. 800ps/nm chromatic dispersion 16-bit parallel 622.08Mbps LVDS data interface The transmitter converts the electrical data into Compliant I2C MSA (Edition 4.0) interface for 10Gbit/s optical signal, which uses externally EA monitoring/control modulated laser with specified driving circuit. Supply voltage: +5.0V, +3.3V, +1.8V Operating case temperature: -5 to +70 is intended for DWDM system At the receiving side, the incoming data stream is received at 10Gb/s PIN/APD receiver, which Applications converts it into a 10Gb/s electrical data stream. Metro and Long haul DWDM system The MUX section multiplexes 16 parallel 622Mb/s Forward Error Correction (FEC) system electrical channels into a 10Gb/s series data stream Optical Transport Network (OTN) System and sent it to the transmitter. And the DEMUX section demultiplexes the 10Gb/s electrical data Standard stream into 16 parallel 622Mb/s electrical channels. The parallel data is sent out to and get from the Compliant with 300-PIN MSA 300-pin MSA (Multi Source Agreement) compliant Compliant with ITU-T G.691 connector. Compliant with ITU-T G.959.1 Compliant with Telcordia GR-253 The transmitter and receiver reference clock rates Compliant with OIF SFI-4 interface are selectable for divide by 16 or 64. Compliant with Telcordia GR-468-Core Compliant with IEC-60825-1 Class DS-5229 Rev 00 2010-07-02 TPD-MR-04-XXXXXXXX Function Block Diagram Figure 1, Function Block Diagram Absolute Maximum Ratings Table 1- Absolute Maximum Ratings Parameter Storage Temperature Supply Voltage Operating Relative Humidity (non-condensing) Electro-Static Discharge Symbol Min. Max. Unit TS -40 85 C Vcc -0.5 6.0 V Vdd1 -0.5 4.2 V Vdd2 -0.5 3.3 V RH 5 85 % ESD - 500 V Recommended Operating Conditions Table 2 - Recommended Operating Conditions Parameter Operating Case Temperature Supply Voltage Symbol Min. Typ. Max. Unit TC -5 - 70 C Vcc 4.75 5.0 5.25 V Vdd1 3.13 3.3 3.46 V Vdd2 1.71 1.8 1.89 V DS-5229 Rev 00 2010-07-02 TPD-MR-04-XXXXXXXX Supply Current Icc - 250 400 mA Idd1 - 400 700 mA Idd2 - 650 800 mA Pd - 3.8 6.0 W - - 50 mVp-p 9.95 - 11.3 Gbps Power consumption Power supply noise rejection Bit Rate BR Optical Interface Characteristics Table 3 - Optical Characteristics Transmitter Parameter Symbol Min. Typical Max. Unit C 1528.773 - 1565.047 nm fc 191.80 - 196.10 THz POUT -2 - 2 dBm 1 P -0.5 - 0.5 dBm 1 P0UT-OFF - - -30 dBm - 100 - GHz -100 - 100 pm SMSR 45 - - dB ER 8.2 - - dB - - 800 ps/nm Wavelength Range Output Power Output Power Stability Output Power at laser disable Channel Spacing Wavelength Stability Side Mode Suppression Ratio Extinction Ratio Chromatic Dispersion Output Optical Eye Notes Compliant with Telcordia GR-253-CORE and ITU-T G.691 20kHz~80MHz - - 0.3 UI 2 4MHz~80MHz - - 0.1 UI 2 1528 - 1565 nm - -18 -17 - -25 -24 0 - - -9 - - Optical Path Penalty - - 2 dB Reflection of Receiver - - -27 dB Jitter Generation Receiver C Centre Wavelength Receiver PIN Sensitivity APD Receiver PIN Overload APD PIN PIN-MAX dBm 3 dBm 3 Jitter Tolerance Compliant with Telcordia GR-253 and ITU-T G.825 Jitter Transfer Compliant with Telcordia GR-253 and ITU-T G.825 Notes: 1. The optical power is launched into SMF. 31 2. Measured with a NRZ PRBS 2 -1 test pattern @ 9.95328Gbps. 31 -12 3. Measured with a NRZ PRBS 2 -1 test pattern @ 9.95328Gbps, BER 1x10 . DS-5229 Rev 00 2010-07-02 TPD-MR-04-XXXXXXXX Electrical Interface Characteristics Table 4 - LVDS Input/Output Specification Parameter Symbol Min. Typical Max. Unit Input Differential Voltage VID 200 - - mV Input Differential impedance RID 80 100 120 Output Differential Voltage VOD 500 - 800 mV Output Differential impedance ROD 80 100 120 Output Common Mode Voltage VCM 1.1 1.2 1.3 V Trise/fall 100 - 250 ps TDC 45 50 55 % Rise Time/Fall time Clock Signal Duty Cycle Notes VP Common Mode Voltage (VCMI or VCMD) Differantial Voltage (VOD or VID) VN Definition of Differantial Voltage Levels Table 5 - LVTTL Input/Output Specification Parameter Symbol Min. Typical Max. Unit Input High Voltage VIH 2.0 - Vdd1 V Input Low Voltage VIL GND - 0.8 V Output High Voltage VIH 2.4 - Vdd1 V Output Low Voltage VIL GND - 0.4 V Notes Clock and Data Interfaces Table 6 - Reference Clock characteristics Transmitter Parameter Frequency Symbol Min. TxREFCLKP tolerance Max. 155.52/622.08 TxREFCLKN Frequency Typical Unit Notes MHz Serial data-rate is 9.953Gbps -100 - +100 ppm Rise/Fall time Tr/Tf - - 500 ps Duty Cycle TDC 40 50 60 % Receiver Frequency RxREFCLKP RxREFCLKN 155.52/622.08 MHz Serial data-rate is 9.953Gbps DS-5229 Rev 00 2010-07-02 TPD-MR-04-XXXXXXXX Frequency tolerance -100 - +100 ppm Rise/Fall time Tr/Tf - - 500 ps Duty Cycle TDC 40 50 60 % Table 7 - Transmitter/Receiver Parallel Data/Clock Interface Parameter Transmitter 16-bit parallel Date Input Transmitter Source Symbol Level Notes TxDin[0:15]P/N LVDS TxDin0:LSB, TxDin15:MSB TxPICLKP/N LVDS TxPCLKP/N LVDS RxDout[0:15]P/N LVDS RxPOCLKP/N LVDS synchronous ParallelInput Clock Transmitter Counter Clock Receiver 16-bit parallel Date Output Receiver Source synchronous Parallel Output Clock RxDout0:LSB, RxDout15:MSB Table 8 - Transmitter/Receiver Parallel Data/Clock Timing Transmitter Data/Clock Timing: SERDES Input Timing at SERDES pin Parameter TxPICLK TxDin Symbol Min. Typical Max. Unit Duty Cycle(TW/TO) TDC 40 50 60 % Rise and Fall time Tr/Tf 100 - 300 ps Setup time Ts 250 - - ps Hold time Th 250 - - ps Notes 20 - 80% To Tw TxPICLKP TxDin[0:15]P/N Th Ts Ts: Measuring from the LHS inner data eye to the immediate rising edge of clock pulse Th: Measuring from the rising edge of clock pulse to the inner RHS of data eye Receiver Data/Clock Timing: SERDES Output Timing at SERDES pin RxPOCLK RxDout Duty Cycle(TW/TO) TDC 40 - 60 % Rise and Fall time Tr/Tf 100 - 250 ps Data/Clock skew Tcq_min, - - 200 ps Tcq_max - - 200 ps DS-5229 20 - 80% Rev 00 2010-07-02 TPD-MR-04-XXXXXXXX To Tw RxPOCLKP Tcq_max RxDout[0:15]P/N Tcq_min Table 9 - Monitor Clock Parameter Symbol Level Transmitter Notes The LVDS TxMCLK is either a 1/16 or 1/64 replica of the monitor clock TxMCLKP/N LVDS clock used to time the serial data output. The rate of the TxMCLK is always the same as that of the TxREFCLK Receiver RxMCLKP/N monitor clock LVDS The LVDS RxMCLK is a 1/16 or 1/64 replica of the clock recovered from the incoming data Digital Control Signal Table 10 - Input Digital signals Function Symbol Module RESET Diagnostic Loopback Line Loopback Level MOD_RESET LVTTL DLOOPENB LVTTL LLOOPENB LVTTL Description Note L Module reset Reset both Tx and Rx section H Normal operation (LVTTL with pull-up resistor) L Enable Loopback H Normal operation L Enable Loopback H Normal operation (LVTTL with pull-up resistor) (LVTTL with pull-up resistor) Transmitter Reset MUX TxRESET Transmitter Bit TxRATESEL1 Rate Select TxRATESEL0 Select frequency LVTTL LVTTL the of TxREFSEL LVTTL TxLINETIMSEL LVTTL LsENABLE LVTTL TxREFCLK Enable internal Line Timing Enable/Disable Laser L Reset MUX H Normal operation 0,0 10.3G 0,1 11.1/11.3G 1,0 10.7G 1,1 9.9G L 1/64 data-rate H 1/16 data-rate L Enable H Normal operation L Normal operation H Laser disabled (LVTTL with pull-up resistor) (LVTTL with pull-up resistor) (LVTTL with pull-up resistor) (LVTTL with pull-up resistor) (LVTTL with pull-down resistor) DS-5229 Rev 00 2010-07-02 TPD-MR-04-XXXXXXXX Internally TxFIFOERR is L MUX FIFO reset TxFIFORES MUX FIFO reset LVTTL connected to TxFIFORES, TxFIFOERR will initiate a FIFO H Normal operation reset (LVTTL with pull-up resistor) Receiver Reset DEMUX Receiver Bit Rate Select Select RxRESET RxRATESEL1 RxRATESEL0 LVTTL LVTTL the frequency of RxREFSEL LVTTL RxMCLKSEL LVTTL RxREFCLK Select the frequency of Lock to RxLCKREF Mutes RxMUTEDOUT RxMUTEMCLK LVTTL 10.3G 0,1 11.1/11.3G 1,0 10.7G 1,1 9.9G L 1/64 data-rate H 1/16 data-rate L 1/64 data-rate H 1/16 data-rate L Lock to RxREFCLK H Normal operation (LVTTL with pull-down resistor) Mutes the RxDOUT[0:15] H Normal operation L Mutes the RxMCLK H Normal operation (LVTTL with pull-up resistor) (LVTTL with pull-up resistor) Mutes receiver Mutes the L parallel output RxMUTEPOCLK (LVTTL with pull-up resistor) (LVTTL with pull-up resistor) LVTTL monitor clock clock 0,0 L the receiver output Normal operation (LVTTL with pull-up resistor) the RxDOUT[0:15] H LVTTL RxREFCLK Mutes Reset DEMUX (LVTTL with pull-up resistor) RxMCLK RxPOCLK L RxPOCLK LVTTL (LVTTL with pull-up resistor) H RxPOCLK Normal operation Digital Alarm Signal Table 11 - Alarms Digital signals Function Symbol Level Description Note Any alarm from Indicates alarm active all ALMINT LVTTL L both transmitter and receiver H Activation Time: 10ms Deactivation Time: 10ms Normal operation Transmitter DS-5229 Rev 00 2010-07-02 TPD-MR-04-XXXXXXXX Loss of Tx PLL lock MUX FIFO error TxLOCKERR TxFIFOERR LVTTL LVTTL L Alarm active H Normal operation L H Alarm active (FIFO overflow) Normal operation Alarm active Laser bias out of range LsBIASALM LVTTL Laser temperature out LsTEMPALM power output out of LsPOWALM TxALMINT current alarm) H Normal operation L Alarm active H Normal operation L Alarm active H Normal operation LVTTL Activation Time: 10ms Deactivation Time: 10ms Internally TxFIFOERR is connected to TxFIFORES, Alarm when laser bias changes by a factor of 2 from beginning of life Activation Time: 10 ms Deactivation Time: 10 ms Laser temperature 5C from nominal, Activation Time : 10ms LVTTL range Tx alarms (laser bias LVTTL of range Laser L Loss of transmitter PLL lock Deactivation Time : 10ms Output power degrades 3dB below the BOL Activation Time : 10ms L H Alarm from transmitter Normal operation Deactivation Time : 10ms Activation Time: 10 ms; Deactivation Time: 10 ms Receiver Loss of Rx PLL lock RxLOCKERR LVTTL Loss of receiver average power RxPOWALM LVTTL RxSIGALM LVTTL alarm Loss of receiver a.c.power alarm Rx alarms RxALMINT LVTTL L Alarm active H Normal operation L Alarm active H Normal operation L Alarm active H Normal operation L H Alarm from Receiver Normal operation Activation Time: 10ms Deactivation Time: 20ms Activation Time: <10ms Deactivation Time: <10ms Activation Time: 10 ms; Deactivation Time: 10 ms Activation Time: 10 ms; Deactivation Time: 10 ms Analog Monitoring Signal Table 12 - Monitor Signals Transmitter Function Normalized laser power monitor voltage BOL Laser power monitor voltage slope Laser bias monitor voltage offset Laser bias monitor voltage slope Normalized laser temperature Monitor voltage Symbol LsPOWMON LsBIASMON LsTEMPMON Min. 0.47 Typ. 0.5 Max. Unit 0.53 V 0.25 V change for 50% power variation 0.2 0 2 V 18 20 22 mV/mA 2.4 2.5 2.6 V DS-5229 Rev 00 2010-07-02 TPD-MR-04-XXXXXXXX Laser temperature monitor voltage slop Normalized laser wavelength monitor voltage Laser temperature monitor voltage slop LsWAVEMON 23 25 27 mV/ - 1.25 - V - 200 - mV/GHz 0.8 1 1.0 V/mW 6 8 10 V/mW -2 - +2 dB Receiver Input optical power monitor voltage PIN slope APD Input optical power monitor error RxPOWMON I2C Serial Interface Table 13 - I2C Interface Function I2C Address Symbol Level I2CAD0 LVTTL I2CAD1 LVTTL I2CAD2 LVTTL I2C Clock I2CCLOCK I2C Data I2CDATA Description Note I2C address input for module (LVTTL with pull-down addressing (LSB) resistor) I2C address input for module (LVTTL with pull-down addressing resistor) I2C address input for module (LVTTL with pull-down addressing (MSB) resistor) Open I2C clock input/output for collector remote access Open I2C data input/output for collector remote access N/A N/A DS-5229 Rev 00 2010-07-02 TPD-MR-04-XXXXXXXX Pin Definitions Table 15 - Pin Function Definitions K J H G F E D C B A 1 +5V NUC GND RxDout12P +1.8V RxDout8P GND RxDout4P GND RxDout0P 2 +5V FFU GND RxDout12N +1.8V RxDout8N GND RxDout4N GND RxDout0N FFU GND RxPOWMON GND I2CAD0 GND FFU GND 3 RxRATESEL0 RxRATESEL1 4 +3.3V NUC GND RxDout13P +3.3V RxDout9P GND RxDout5P GND RxDout1P 5 +3.3V NUC GND RxDout13N +3.3V RxDout9N GND RxDout5N GND RxDout1N 6 RxRESET NUC DLOOPENB GND RxPOWALM GND I2CAD1 GND RxMUTE Dout GND 7 +3.3V FFU GND RxDout14P +3.3V RxDout10P GND RxDout6P GND RxDout2P 8 +3.3V FFU GND RxDout14N +3.3V RxDout10N GND RxDout6N GND RxDout2N NUC FFU GND NUC GND I2CAD2 GND RxLCKREF GND 9 RxMUTEPOCLK 10 NUC NUC GND RxDout15P NUC RxDout11P GND RxDout7P GND RxDout3P 11 NUC NUC GND RxDout15N NUC RxDout11N GND RxDout7N GND RxDout3N NUC FFU GND RxSIGALM GND MOD RESET GND RxMCLKSEL GND 12 RxMUTEMCLK 13 NUC FFU GND FFU NUC RxPOCLKP GND RxMCLKP GND RxREFCLKP 14 NUC RxALMINT GND FFU NUC RxPOCLKN GND RxMCLKN GND RxREFCLKN 15 I2CCLOCK NUC ALM INT GND RxREFSEL GND FFU GND RxLOCKERR GND 16 +5V TxALMINT GND TxDin12P +1.8V TxDin8P GND TxDin4P GND TxDin0P 17 +5V FFU GND TxDin12N +1.8V TxDin8N GND TxDin4N GND TxDin0N 18 I2CDATA NUC FFU GND LsBIASMON GND LsPOWMON GND NUC GND 19 +3.3V FFU GND TxDin13P +3.3V TxDin9P GND TxDin5P GND TxDin1P 20 +3.3V FFU GND TxDin13N +3.3V TxDin9N GND TxDin5N GND TxDin1N FFU GND LsENABLE GND LsTEMPMON GND NUC GND 21 TxRATESEL0 TxRATESEL1 22 +3.3V FFU GND TxDin14P +3.3V TxDin10P GND TxDin6P GND TxDin2P 23 +3.3V FFU GND TxDin14N +3.3V TxDin10N GND TxDin6N GND TxDin2N 24 TxRESET NUC FFU GND LsBIASALM GND FFU GND FFU GND 25 NUC NUC GND TxDin15P NUC TxDin11P GND TxDin7P GND TxDin3P 26 NUC NUC GND TxDin15N NUC TxDin11N GND TxDin7N GND TxDin3N 27 TxFIFORES NUC LLOOPENB GND LsTEMPALM GND FFU GND TxPICLKSEL GND 28 NUC LsWAVEMON GND TxPICLKP NUC TxPCLKP GND TxMCLKP GND TxREFCLKP 29 NUC FFU GND TxPICLKN NUC TxPCLKN GND TxMCLKN GND TxREFCLKN 30 TxFIFOERR NUC TxLINETIMESEL GND TxREFSEL GND LsPOWALM GND TxLOCKERR GND FFU: Reserved For Future Use NUC: No Use Connection DS-5229 Rev 00 2010-07-02 TPD-MR-04-XXXXXXXX Mechanical Diagram The mechanical design diagram is shown in Figure 2. Figure 2, Mechanical Diagram Ordering Information Part No. TPD-MR-04-XXCDL5A TPD-MR-04-XXCDL5B TPD-MR-04-XXCDS5A TPD-MR-04-XXCDS5B TPD-MR-04-XXCDF5A TPD-MR-04-XXCDF5B Product Description C-band DWDM Wavelength, 9.95~11.3Gbps, 40km, PIN receiver, 10G SFF 300pin, LC connector, -5C~+70C, C-band DWDM Wavelength, 9.95~11.3Gbps, 40km, APD receiver, 10G SFF 300pin, LC connector, -5C~+70C, C-band DWDM Wavelength, 9.95~11.3Gbps, 40km, PIN receiver, 10G SFF 300pin, SC connector, -5C~+70C, C-band DWDM Wavelength, 9.95~11.3Gbps, 40km, APD receiver, 10G SFF 300pin, SC connector, -5C~+70C, C-band DWDM Wavelength, 9.95~11.3Gbps, 40km, PIN receiver, 10G SFF 300pin, FC connector, -5C~+70C, C-band DWDM Wavelength, 9.95~11.3Gbps, 40km, APD receiver, 10G SFF 300pin, FC connector, -5C~+70C, Note: XX is from 18 (191.80THz) to 61(196.10THz)100GHz spacing. DS-5229 Rev 00 2010-07-02 TPD-MR-04-XXXXXXXX Warnings Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notice IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at Source Photonics's sole and absolute discretion. Source Photonics warrants performance of its products to current specifications only in accordance with the company's standard one-year warranty; however, specifications designated as "preliminary" are given to describe components only, and Source Photonics expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company's Terms and Conditions of Sale for further warranty information. Source Photonics assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and Source Photonics makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. Source Photonics customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify Source Photonics for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN "AS IS" BASIS. Customer agrees that Source Photonics is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact Source Photonics to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. Contact U.S.A Headquaters China Taiwan 20550 Nordhoff Street Building #2&5, West Export Processing 9F, No 81, Shui Lee Rd. Chatsworth, CA 91311 Zone No. 8 Kexin Road, Hi-Tech Zone Hsinchu, Taiwan, R.O.C. USA Chengdu, 611731, China Tel: +886-3-5169222 Tel: +1-818-773-9044 Tel: +86-28-8795-8788Fax: Fax: +886-3-5169213 Fax: +1-818-773-0261 +86-28-8795-8789 (c) Copyright Source Photonics, Inc. 2007~2010 All rights reserved DS-5229 Rev 00 2010-07-02