TQQ7307
2535 MHz LTE Band 7 Uplink BAW Filter
Applications
• LTE Band 7 Uplink Infrastructure
• Base Station
• General Purpose Wireless
6 Pin 3 x 3 mm leadless SMT Package
Functional Block Diagram
1
2
34
5
6
Top View
Ordering Informa ti on
Part No.
Description
TQQ7307
2535 MHz BAW Filter
TQQ7307-EVB
Evaluation bo ard
Standard T/R size = 2500 pieces on a 7" r eel
Product Fe a t ures
• 70 MHz Bandwidth
• High Attenuation
• Low Loss
• 50 Ohm Input/Output Impedance
• Single-ended Operation
• Small Size: 3 x 3 x 1.02 mm
• Surface Mount Device
• RoHS Com pliant, Pb-Free
Gener a l Des cr iption
The TQQ7307 is a general purpose uplink BAW filter for
LTE
Band 7. Th is filter is housed i n a compac t 3 x 3
mm
packag
e for base station applications.
Low insertion loss, coupled with high attenuation makes
this filter
an ideal choice for uplink RF filtering needs.
The
TQQ7307 is part of TriQuint’s extensive portfolio o
f
RF
BAW and SAW filters.
Pin Configuration
Pin No.
Label
2
Input
5
Output
1,3,4,6
Ground
Ground
Input
Ground
Ground
Output
Ground
Advanced Datasheet: Rev B 07-16-14 - 1 of 8 - Disclaimer: Subject to change without notice
© 2014 TriQuint www.triquint.com
TQQ7307
2535 MHz LTE Band 7 Uplink BAW Filter
Recomme nded O pe rating Conditions
Parameter
Min
Typ
Max
Units
T
CASE
−40
+85
°C
Electrical specifications are measured at specified test
conditions.
Absolute Maximum Ratings
Parameter
Rating
Storage Temperature
−40 to +95°C
RF Input Power
(CW, +55°C for 10, 000 hou r s)
+30 dBm
Operation of this device outside the parameter ranges
given above may cause permanent damage.
Electrical Specifications (1,2,3)
Test conditions unless otherwise specified: Temp. +25 ° C, ZS=ZL=50 Ohms
Parameter
Conditions
Min
Typ(4)
Max
Units
Pass Band Frequency
2500
2570
Center Frequency
-
2535
-
MHz
3.5 dB Bandwidth
-
83
-
MHz
Maximum Insertion Loss
2500 – 2570 MHz
-
2.0
3.5
dB
Amplitude Variation(5)
2500 – 2570 MHz
-
0.9
2.4
dB
Group Delay Variation(6)
2500 – 2570 MHz
-
14
30
ns p-p
Group Delay Variation(6)
Any 5 MHz band in passba nd
-
7
13
ns p-p
Input VSWR
2500 – 2570 MHz
-
1.9:1
2.4:1
-
Output VSWR
2500 – 2570 MHz
1.8:1
2.4:1
-
Stopband Atte nuation
(relative to zero dB)
0.9 – 1100 MHz
1100 – 2170 MHz
2170 – 2260 MHz
2260 – 2450 MHz
2450 – 2480 MHz
2590 – 2620 MHz
2620 – 2690 MHz
2690 – 2900 MHz
2900 – 3800 MHz
3800 – 5000 MHz
5000 – 6000 MHz
36
30
38
32
12
8
40
40
30
13
-
40
34
45
39
20
12
48
47
37
17
4
-
-
-
-
-
-
-
-
-
-
-
dB
Source/Load Impedance (7)
Single ended
-
50
-
Ohms
Notes:
1. All specifications are based on the TriQuint schematic for the main reference design.
2. Production test is performed at room temp. to a guard-banded speci fic atio n to ensure electrical comp lian ce ov er temperature.
3. Electrical margin has been built into the design to account for variation due to temperature drift and manufacturing tolerances.
4. Typical values are based on average measurements at room temperature of 25°C.
5. This is defined as the difference between the maximum and minimum insertion loss within the specified band.
6. This is defined as the worst case difference between a peak and adjacent valley within defined frequency points.
7. This is the optimum impedance in order to achieve the performance shown.
Advanced Datasheet: Rev B 07-16-14 - 2 of 8 - Disclaimer: Subject to change without notice
© 2014 TriQuint www.triquint.com
TQQ7307
2535 MHz LTE Band 7 Uplink BAW Filter
TQQ7307-PCB Eval ua t ion Board
Q7307
1,3,4,6
25
50 50
ΩΩ
Bill of Material – TQQ7307-PCB
Reference Des.
Value
Description
Manuf.
Part Number
U1
n/a
2535 MHz BAW Filter
TriQuint
TQQ7307
n/a
n/a
Printed Circuit Board
TriQuint
960700
n/a
n/a
SMA Edge Connector
Radiall
9602-1111-018
Evaluat ion Board PCB Information
Top, middle & bottom layers: 1 oz copper
Substrates: FR4 dielectric, .031” thick
Finish plati ng: Nick el: 3-8µm thick, Gold: .03-.2µm thick
Hole plating: Copper min .0008µm thick
Single-ended
Input
Single-ended
Output
Advanced Datasheet: Rev B 07-16-14 - 3 of 8 - Disclaimer: Subject to change without notice
© 2014 TriQuint www.triquint.com
TQQ7307
2535 MHz LTE Band 7 Uplink BAW Filter
Perf orm a nc e Plots
Test conditions unless otherwise noted:
Temp= +25°C
Frequen cy R esponse
d
B
Frequen cy (M Hz)
-70
-60
-50
-40
-30
-20
-10
0
2335 2385 2435 2485 2535 2585 2635 2685 2735
P assband Resp ons e
d
B
Frequen cy (M Hz)
-5
-4.6
-4.2
-3.8
-3.4
-3
-2.6
-2.2
-1.8
-1.4
-1
2482.5 2500 2517.5 2535 2552.5 2570 2587.5
Wi deband Respo nse
d
B
Frequen cy (M Hz)
-70
-60
-50
-40
-30
-20
-10
0
0750 1500 2250 3000 3750 4500 5250 6000
I nput / O utput VS WR
Frequen cy (M Hz)
1
1.4
1.8
2.2
2.6
3
2482.5 2500 2517.5 2535 2552.5 2570 2587.5
1
1.4
1.8
2.2
2.6
3
2482.5 2500 2517.5 2535 2552.5 2570 2587.5
I nput S mi th C hart
-1
-0.8
-0.6
-0.4
-0.2
0
0.2
0.4
0.6
0.8
1
-1 -0.5 00.5 1
Out put S mi th C hart
-1
-0.8
-0.6
-0.4
-0.2
0
0.2
0.4
0.6
0.8
1
-1 -0.5 00.5 1
Advanced Datasheet: Rev B 07-16-14 - 4 of 8 - Disclaimer: Subject to change without notice
© 2014 TriQuint www.triquint.com
TQQ7307
2535 MHz LTE Band 7 Uplink BAW Filter
Package Marking and Dimensions
TOP VIEW
BOTTOM VIEW
Pin #1 Identifier
3.00±0.10
3.00±0.10
(5X) 0.650x X 0.600y
0.10 C A B (1X) 1.400x X 0.600y
0.10 CA B
PIN 1
3.00±0.10
3.00±0.10
0.100±0.100
0.100±0.100
1.100
1.100
1.071 0.700
1.075
2x 0.10 C
2x 0.10 C
B
A
SIDE VIEW
0.10 CC
3.00±0.10
1.02±0.07
Notes:
1. All dimensions are in mil lim et e rs
2. All tolerances are ±0.15 mm except overall length and width ±0.10 mm
3. Contact plating : ENIG (Electroless Nickel Immersion Gold)
4. Terminations: 0.5 – 1.0 μm Au plating, over a 2 – 6 μm Ni plating
PCB Mounting Pattern
Notes:
1. All dimensions are in millim ete rs. Angles are in degrees.
2. Use 1 oz. copper minimum for top and bottom layer metal.
Q7307
YYWW
aXXXX
Package Marking
Product Identif i er: Q7307
Date Code: YYWW
Assembly Code: AaXXXX
Advanced Datasheet: Rev B 07-16-14 - 5 of 8 - Disclaimer: Subject to change without notice
© 2014 TriQuint www.triquint.com
TQQ7307
2535 MHz LTE Band 7 Uplink BAW Filter
Tape and Ree l I nfor m a t ion – Carrier and Cover Ta pe Dim e nsions
Tape and reel specifications for this part are also available on the TriQuint website
.
Standard T/R size = 2500 pieces on a 7” reel.
Feature
Measure
Symbol
Size (in)
Size (mm)
Cavity
Length
A0
0.132
3.35
Width
B0
0.132
3.35
Depth
K0
0.055
1.40
Pitch
P1
0.157
4.00
Centerline
Distance
Cavity to Perforation - Length Direction
P2
0.079
2.00
Cavity to Perforation - Width Direction
F
0.138
3.50
Cover Tape
Width
C
0.213
5.40
Carrier Tape
Width
W
0.315
8.00
Advanced Datasheet: Rev B 07-16-14 - 6 of 8 - Disclaimer: Subject to change without notice
© 2014 TriQuint www.triquint.com
TQQ7307
2535 MHz LTE Band 7 Uplink BAW Filter
Tape and Ree l I nfor m a t ion – Reel Dimensi ons
Tape and reel specifications for this part are also available on the TriQuint website
.
Standard T/R size =
2,500 pieces on a 7” reel.
Feature
Measure
Symbol
Size (in)
Size (mm)
Flange
Diameter
A
6.969
177.0
Thickness
W2
0.559
14.2
Space Between Flange
W1
0.346
8.8
Hub
Outer Diameter
N
2.283
58.0
Arbor Hole Diameter
C
0.512
13.0
Key Slit Width
B
0.079
2.0
Key Slit Diameter
D
0.787
20.0
Advanced Datasheet: Rev B 07-16-14 - 7 of 8 - Disclaimer: Subject to change without notice
© 2014 TriQuint www.triquint.com
TQQ7307
2535 MHz LTE Band 7 Uplink BAW Filter
Product Com pliance Information
ESD Sens it ivity Ratings
Caut ion! ES D-Sensitive Device
ESD Rating:
Class 1B
Value:
Passes ≥ 500V to < 1000V
Test:
Human Body Model (HBM)
Standard:
JEDEC Standard JS-001-2012
ESD Rating:
Class B
Value:
Passes ≥ 200V to < 400V
Test:
Machine Model (MM)
Standard:
JEDEC Standard JESD22-A115
Solderability
Compatible with both lead
-
free (260°C maximum reflow
temperature) and tin/lead (245°C maximum reflow
temperature) soldering processes.
Contact plati ng:
ENIG (Electroless Nickel Immersion Gold)
RoHs Compliance
This part
is
compliant with EU 2002/95/EC RoHS directive
(Restrictions on the Use of Certain Hazardous Substances
in El
ectr ical and E lectr on ic Equ ipment).
This product also has the following attributes:
• Lead Free
• Halogen Free (Chlorine, Bromine)
• Antimony Free
• TBBP-A (C15H12Br402) Free
• PFOS Free
• SVHC Free
MSL Rati ng
MSL Rating:
Level 3
Test:
260°C convection reflow
Sta
ndard: JEDEC Standard IPC/JEDEC J-STD-020
Contact Information
For the lates t specific ations, add itional prod uct infor mation, worldwide sal es and distr ibution loca tions, and inf orm ation
about TriQuint:
Web: www.triquint.com Tel: +1.407.886.8860
Email: info-sales@triquint.com Fax: +1.407.886.7061
For technical questions and application information:
Email: flapplication.engineering@triquint.com
Impor t a nt Notice
The information contained herein is believed to be reliable. TriQuint makes no warranties regarding the information
contained herein.
TriQuint assumes no responsibility or liabili
ty whatsoever for any of the information contained
herein. T riQuint assum es no respons ibilit y or liabilit y whatsoever f or the use of the inform ation cont ained herein. The
information contained herein is provided "AS IS, WHERE IS" and with all faults, and the entire risk associated with
such information is entirely with the user. All information contained herein is subject to change without notice.
Customers should obtain and verify the latest relevant information before placing orders for TriQuint products. The
information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any
patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or
anything described by such information.
TriQuint products are not warranted or authorized for use as critical components in medical, life
-saving, or life
-
sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal
injury or death.
Advanced Datasheet: Rev B 07-16-14 - 8 of 8 - Disclaimer: Subject to change without notice
© 2014 TriQuint www.triquint.com
