EYP-1BF145 - Panasonic - Datasheet.Directory

Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.

Should a safety concern arise regarding this product, please be sure to contact us immediately.

Thermal Cutoffs (TCO)

Insulating case

(Ceramic)

Lead wire

(Tin plating copper)

Sealant

(Epoxy resin)

Special resin

(Flux)

Fusible alloy

(Pb·Cd free)

Sealant (Epoxy resin) Fusible alloy (Pb·Cd free)

Special formed

lead wire

(Tin plating copper)

Special resin

(Flux)

Insulating

case(Ceramic)

Insulating ﬁlm

Terminal (Ni or Ni plating)

Special resin (Flux)

Fusible alloy (Pb·Cd free)

● Small and Insulation Type

TCO is compact and insulated, featuring quick temperature response, and mountable in a small space without

insulation or protection.

● High Reliability

TCO opens reliably when the equipment becomes abnormal, and is not resettable.

● Solid Structure

Uniquely formed lead provides reliable TCO connection and provides easy assembly handling. (Axial lead type only)

● Thin Type

Thick is less than 0.8 mm (MP series), available for spot welding (MP and MU series)

● Halogen-free (Thin type MP and MU series)

The thin type fuses with a part number listed in this catalog contain no halogen other than any that may exist as an impurity.

● RoHS compliant

● (Japan) : Approved by JET

● UL, C-UL (U.S.A.) : E60271

● CSA (Canada) : 1□□□□□□ (LR67163)

● VDE (Germany) : 481106-1171-□□□□

● BEAB (U.K.) : C□□□□

● CCC (China) : 20020102050042□□

See Ratings in details.

●

Transformers, Solenoids, Ventilation fans, Electric fans, Small electric motors, Driers, Gas home appliances, Fluorescent

lights, Electric shavers, Adaptors, Heating devices, ICs, Batteries, etc. The TCO can also be used for overheating protection.

Thermal Cutoffs (TCO)/

Thermal-links

EYP Series: N

Series: F

Series: E

Series: H

Series: MP

Series: MU

● Axial lead type (N, F and E series)

● Thin type (MP and MU series)

● Radial lead type (H series)

✽ Thin type is not to be soldered.

Features

Approved Safety Standards

Recommended Applications

Construction

Jan. 201503

Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.

Should a safety concern arise regarding this product, please be sure to contact us immediately.

Thermal Cutoffs (TCO)

Ratings

Note: (1) For long lead types add the letter “L” at the end op the part number.

(2) The information of the Approved Safety Standards is furnished as of Jun. 2010.

Approved Safety Standards File No. UL:E60271, CSA:1687496(LR67163), VDE:481106-1171-0001, BEAB:C1144, CCC:2011010205464841

● F series

● N series

Part No.

Type No. of

Approved

Standards

Rated

Functioning

Temp. : Tf

✽1

(°C)

Functioning

Temp. ✽2

(°C)

Electrical Rating Maximum

Operating

Temp. ✽3

(°C)

Holding

Temp. : Th

✽4

(°C)

Maximum

Temp.

Limit : Tm

✽5

(°C)

Approved Safety

Standards

AC/

Volt.

(V)

Amp.

(A)

EUL CSA VDE

BEAB

CCC

EYP2BN082 N082 86 82±2

AC 250 2 60 60

200

○○○○○○

AC 125 3 52 56 — ○○○○—

DC 50 4 45 50 — ○○○○—

EYP2BN099 N099 102 98+4

AC 250 2 65 75

200

○○○○○○

AC 125 3 60 70 — ○○○○—

DC 50 4 55 65 — ○○○○—

EYP2BN109 N109 114 110±3

AC 250 2 80 90

200

○○○○○○

AC 125 3 76 86 — ○○○○—

DC 50 5 65 74 — ○○○○—

EYP2BN110 N110 115 110+3

AC 250 2 80 90

200

○○○○○○

AC 125 3 76 86 — ○○○○—

DC 50 5 65 74 — ○○○○—

EYP2BN127 N127 134 129±4

AC 250 2 90 100

200

○○○○○○

AC 125 3 75 90 — ○○○○—

DC 50 4 65 80 — ○○○○—

EYP2BN134 N134 139 135±3

AC 250 2 100 110

200

○○○○○○

AC 125 3 85 100 — ○○○○—

DC 50 6 60 70 — ○○○○—

EYP2BN143 N143 145 141±2

AC 250 2 110 120

200

○○○○○○

AC 125 3 105 115 — ○○○○—

DC 50 6 80 90 — ○○○○—

–2

–3

Note: (1) For long lead types add the letter “L” at the end op the part number.

(2) The information of the Approved Safety Standards is furnished as of Jun. 2010.

Approved Safety Standards File No. UL/C-UL:E60271, CSA:1709436(LR67163), VDE:481106-1171-0003, BEAB:C1133, CCC:2011010205464842

Part No.

Type No. of

Approved

Standards

Rated

Functioning

Temp. : Tf

✽1

(°C)

Functioning

Temp. ✽2

(°C)

Electrical Rating Maximum

Operating

Temp. ✽3

(°C)

Holding

Temp. : Th

✽4

(°C)

Maximum

Temp.

Limit : Tm

✽5

(°C)

Approved Safety

Standards

AC/

Volt.

(V)

Amp.

(A)

C-UL CSA VDE

BEAB

CCC

EYP1BF101 F101 102 98±3

AC 250 1 65 75

200

○○○○○○

AC 125 2 60 70 — ○○○○—

DC 50 3.5 55 65 — ○○○○—

EYP1BF115 F115 115 110+3

AC 250 1 80 90

200

○○○○○○

AC 125 2 76 90 — ○○○○—

DC 50 4 70 80 — ○○○○—

EYP1BF134 F134 134 129+4

AC 250 1 90 105

200

○○○○○○

AC 125 2 85 100 — ○○○○—

DC 50 4 65 80 — ○○○○—

EYP1BF138 F138 139 135±3

AC 250 1 100 110

200

○○○○○○

AC 125 2 90 105 — ○○○○—

DC 50 5 65 70 — ○○○○—

EYP1BF145 F145 145 141±2

AC 250 1 110 125

200

○○○○○○

AC 125 2 110 125 — ○○○○—

DC 50 5 80 95 — ○○○○—

–3

–2

Jan. 201503

Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.

Should a safety concern arise regarding this product, please be sure to contact us immediately.

Thermal Cutoffs (TCO)

Ratings

● E series

● H series

Part No.

Type No. of

Approved

Standards

Rated

Functioning

Temp. : Tf

✽1

(°C)

Functioning

Temp. ✽2

(°C)

Electrical Rating Maximum

Operating

Temp. ✽3

(°C)

Holding

Temp. : Th

✽4

(°C)

Maximum

Temp.

Limit : Tm

✽5

(°C)

Approved Safety

Standards

AC/

Volt.

(V)

Amp.

(A)

C-UL CSA VDE

BEAB

CCC

EYP05BE101 E101 102 98±3

AC 250 0.5 65 75

200

○○○○○○

AC 125 1.5 60 70 — ○○○○—

DC 50 3 55 65 — ○○○○—

EYP05BE115 E115 115 110±2

AC 250 0.5 80 95

200

○○○○○○

AC 125 1.5 76 93 — ○○○○—

DC 50 3 70 84 — ○○○○—

EYP05BE134 E134 134 129+4

AC 250 0.5 90 105

200

○○○○○○

AC 125 1.5 85 100 — ○○○○—

DC 50 3 70 85 — ○○○○—

EYP05BE138 E138 139 135±3

AC 250 0.5 100 115

200

○○○○○○

AC 125 1.5 95 110 — ○○○○—

DC 50 4 65 80 — ○○○○—

EYP05BE145 E145 145 141±2

AC 250 0.5 110 125

200

○○○○○○

AC 125 1.5 105 125 — ○○○○—

DC 50 5 80 95 — ○○○○—

–3

Part No.

Type No. of

Approved

Standards

Rated

Functioning

Temp. : Tf

✽1

(°C)

Functioning

Temp. ✽2

(°C)

Electrical Rating Maximum

Operating

Temp. ✽3

(°C)

Holding

Temp. : Th

✽4

(°C)

Maximum

Temp.

Limit : Tm

✽5

(°C)

Approved Safety

Standards

AC/

Volt.

(V)

Amp.

(A)

C-UL CSA VDE

BEAB

CCC

EYP2BH101 H101 102 98±3

AC 250 2 65 75

200

○○○○○○

AC 125 3 60 70 — ○○○○—

DC 50 3.5 55 65 — ○○○○—

EYP2BH115 H115 115 110±2

AC 250 2 80 90

200

○○○○○○

AC 125 3 76 86 — ○○○○—

DC 50 3.5 74 84 — ○○○○—

EYP2BH134 H134 134 129+4

AC 250 2 90 95

200

○○○○○○

AC 125 3 70 85 — ○○○○—

DC 50 3.5 65 80 — ○○○○—

EYP2BH138 H138 139 135±3

AC 250 2 100 105

200

○○○○○○

AC 125 3 80 95 — ○○○○—

DC 50 3.5 75 90 — ○○○○—

EYP2BH145 H145 145 141±2

AC 250 2 110 125

200

○○○○○○

AC 125 3 100 115 — ○○○○—

DC 50 4.5 85 100 — ○○○○—

–3

Note: (1) For long lead types add the letter “L” at the end op the part number.

(2) The information of the Approved Safety Standards is furnished as of Jun. 2010.

Approved Safety Standards File No. UL/C-UL:E60271, CSA:1709439(LR67163), VDE:481106-1171-0002, BEAB:C1139, CCC:2011010205464843

Note: (1) The information of the Approved Safety Standards is furnished as of Jun. 2010.

Approved Safety Standards File No. UL/C-UL:E60271, CSA:1709435(LR67163), VDE:481106-1171-0004, BEAB:C1140, CCC:2011010205464844

Jan. 201503

Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.

Should a safety concern arise regarding this product, please be sure to contact us immediately.

Thermal Cutoffs (TCO)

✽1 Rated Functioning Temperature (Tf)

The temperature at which a TCO changes its state of conductivity to open circuit with loading detection current only.

Tolerance; PS

E ; ±7 °C

UL,CSA,VDE, BEAB, CCC; –10 °C

✽2 Functioning Temperature (Fusing-off temperature)

The functioning temperature at which a TCO changes its state of conductivity to open circuit in the ambient air oven which increases

temperature by 1 °C per minute and with loading the detective current 0.1 A or less.

✽3 Maximum Operating Temperature

The maximum temperature at which a TCO can be maintained while conducting rated current for 1000 h.

For details please refer to specification.

✽4 Holding Temperature (Th)

The maximum temperature at which a TCO can be maintained while conducting rated current for 168 h which will not cause a change in state

of conductivity to open circuit.

✽5 Maximum Temperature Limit (Tm)

The maximum temperature at which a TCO can maintains its mechanical and electrical properties with out closing again for 10

minutes after a TCO has changed its state of conductivity.

● MU series

Note: (1) The information of the Approved Safety Standards is furnished as of Jun. 2010.

Approved Safety Standards File No. UL:E60271

Note: (1) The information of the Approved Safety Standards is furnished as of Jun. 2010.

Approved Safety Standards File No. UL:E60271

Part No.

Rated

Functioning

Temp. : Tf ✽1

(°C)

Functioning

Temp. ✽2

(°C)

Electrical Rating Maximum

Operating

Temp. ✽3

(°C)

Holding

Temp. : Th✽4

(°C)

Maximum

Temp.

Limit : Tm✽5

(°C)

Approved

Safety

Standards

AC/

Volt.

(V)

Amp.

(A) UL

EYP2MP092AFT 92 88+3 DC 32 2 55 60 135 ○

EYP2MP098AFT 98 94+3 DC 32 2 60 65 135 ○

–4

–2.5

Part No.

Rated

Functioning

Temp. : Tf ✽1

(°C)

Functioning

Temp. ✽2

(°C)

Electrical Rating Maximum

Operating

Temp. ✽3

(°C)

Holding

Temp. : Th✽4

(°C)

Maximum

Temp.

Limit : Tm✽5

(°C)

Approved

Safety

Standards

AC/

Volt.

(V)

Amp.

(A) UL

EYP4MU092GFD 92 89+3 DC 32 4 55 55 135 ○

–4

● MP series

Ratings

Jan. 201503

Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.

Should a safety concern arise regarding this product, please be sure to contact us immediately.

Thermal Cutoffs (TCO)

B L

lLl

DG (H)

D(G) (H)

ENB

The following items are indicated on TCO.

• N, F, E, H Series : Type No., Date Code, Trade Mark, <PS>E Mark, JET, Rated Functioning Temperature, Rated Current

• MP, MU Series : Type No., Date Code, Trade Mark

Part No. Standard Quantity Style Mass (Weight) [mg/pc.]

EYP2BN◻◻◻ 2,000 pcs./Box

Bulk

340

EYP2BN◻◻◻L2,000 pcs./Box 510

EYP1BF◻◻◻ 3,000 pcs./Box 220

EYP1BF◻◻◻L4,000 pcs./Box 330

EYP05BE◻◻◻ 4,000 pcs./Box 210

EYP05BE◻◻◻L5,000 pcs./Box 320

EYP2BH◻◻◻ 1,500 pcs./Box 350

EYP2MP◻◻◻AFT 2,000 pcs./Box 54

EYP4MU◻◻◻GFD 1,000 pcs./Box 130

● Radial lead type

● Axial lead type

● Thin type

(✽) For long lead types add the letter “L” at the end op the part number.

Dimensions (mm)

L0D0D1 k0d

N Series 9.0±1.0 2.5±0.2 3 max. 38±3 (✽78±3)

0.60±0.05

F Series 6.0±1.0 1.85+0.20 2.2 max. 38±3 (✽68±3)

0.53±0.02

E Series 5.0±0.5 1.5±0.1 1.8 max. 38±3 (✽68±3)

0.53±0.02

–0.15

Dimensions (mm)

ABCL 0d

H Series 5.0±0.5 4.0±0.5 2.2±0.3 55±3 0.53±0.02

EYP4MU◻◻◻GFD

Dimensions (mm)

A B C D E G (H) J N

EYP2MP◻◻◻AFT 24.5±0.5 2.7±0.2 0.64±0.15 4.2±0.5 2.3±0.2 7.9±0.5 (12.4) 0.10±0.02 –

EYP4MU◻◻◻GFD 26.5±0.5 4.5±0.4 1.00±0.15 10.5±0.5 3.0±0.2 (8.0) (8.0) 0.15±0.02 1.8±0.5

EYP2MP◻◻◻AFT

Dimensions in mm (not to scale)

Marking

Packaging Methods

Jan. 201503

Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.

Should a safety concern arise regarding this product, please be sure to contact us immediately.

Thermal Cutoffs (TCO)

The following are precautions for individual products. Please also refer to the common precautions for fuses in this

catalog.

● Design Applications

1. Use the TCO within their specified temperature and electrical ratings.

1) Use the TCO under the maximum operating temperature specified in the individual specification.

Using the TCO under a higher temperature than the maximum operating temperature may cause premature

open ing or opening delay.

• When the TCO is continuously used at the temperature close to the functioning temperature, the TCO may

op er ate while being used.

• When the TCO is continuously used at the temperature higher than the maximum operation temperature, the

TCO may be degraded and may not operate normally at the specified temperature.

2) The holding temperature is defined as the highest temperature at which the TCO is activated continuously at

the rated current for 168 hours. The TCO can not be used over 168 hours exceeding the holding temperature.

3) Equipment should be designed so that its over shoot does not exceed the maximum temperature limit after the

TCO operates.

4) If the TCO is activated by voltage higher than the rated voltage or current higher than the rated current, the

TCO produces excessive heat, resulting in premature opening. The arc generated in such operating conditions

will result in abnormal appearance (crack on body) and insufficient insulation.

• When TCO is operated in an abnormal mode while the rated voltage and/or the rated current being exceeded,

it may not cut off the circuit.

5) Thermal element may be transformed and TCO may open when it is used in the environment from which an

excessive temperature change (such as outdoor) is repeated. Investigate the environment where TCO is used.

6) Where transient overload is expected to be applied, repeat the tests under the worst conditions.

7) The TCO cannot be used as a current sensitive fuse.

2. To fully use the function of the TCO, a suitable TCO for each equipment application must be selected.

1) Tests should be repeated for the finished equipment to confirm that the TCO does operate as expected.

2) To improve thermal response of the TCO, put the main body of the TCO and the lead wires(terminals) as close

to the heat source as possible and the place where the TCO is evenly heated.

If the temperatures transferred to the main body and to the lead wires(terminals) are largely different from each

other, defective operation may occur, causing arcing and deterioration of insulation.

3. Avoid application of excessive vibration and mechanical stress to the TCO. Otherwise, failure of the fusible alloy

or lead wires, or damage to the main body may occur.

4. The following 1) and 2) are precautions for thin type TCO (MP and MU series)

1) TCO body and terminals must be properly fixed when the TCO is mounted in the equipment. It may cause

breaking of thermal element and/or terminals, or damages of the TCO body, or other failure when the body or

terminals is not properly connected. Avoid a transport under the condition with a connection only a single side

of terminal and the equipment as it might cause breaking of thermal element and/or terminals, or damages of

the TCO body, or other failure due to the vibration or mechanical stress on the transportation.

2) When TCO is mounted in the equipment, terminals must be aligned with the body. If TCO body and

terminals are mutually mounted askew, it might cause breaking of thermal element and/or terminals. Also after

assembling TCO in the equipment, avoid pulling, bending, pushing stress and twisting stress in the TCO body

and terminals in order not to cause breaking of thermal element and/or terminals, or damages of the TCO

body.

5. When sealing the TCO with resin, select a resin that does not corrode the seals or the lead wires(terminals).

When sealing the overall TCO with resin, determine the fixing conditions by repeating the test using your final

product to check whether or not the resin properties (e.g. expansion, contraction, and curing temperature) affect

the TCO and whether or not the TCO can operate normally.

6. When immersing equipment with a TCO in varnish or solvent and then drying it, repeat the test to check whether

or not the varnish or solvent used dissolved the coating of the TCO or caused damage, such as cracks, before

performing the treatment again.

7. Do not use under the following environments.

1) In liquids such as water, oil, chemical and organic solvents

2) In direct sunlight, outdoors or in dusty atmospheres

3) In places where water condensation occurs

✽ Use in the following environments may affect the performance of the TCO; Verify performance and reliability

be fore production use.

(1) In places full of corrosive gases such as sea breeze, Cl2, H2S, NH3, SO2 and NO2

(2) In environments with high static electricity and/or strong electromagnetic waves.

8. Do not use the TCO in aerospace equipment, atomic energy equipment, military weap ons, life saving equip ment,

automobile, etc.

Safety Precautions (Handling Precautions)

Jan. 201503

Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.

Should a safety concern arise regarding this product, please be sure to contact us immediately.

Thermal Cutoffs (TCO)

● Soldering point

> 3 mm > 3 mm > 3 mm > 3 mm

> 3 mm > 3 mm

grasped grasped

Bending Cutting

Fig-1

2. Soldering, Welding, Calking

1) Lead wires are to be soldered with the standard conditions shown in Table 1.

Excessive soldering heat and soldering time may cause damage to a TCO.

If higher temperature, longer time or shorter lead length exist rather than the conditions of Table 1, it is

recommended to run tests for find ing the soldering conditions that do not damage the TCO. Also, use of

tools such as pliers are recommend ed to dissipate the soldering heat by grasping lead wires between the

TCO body and soldering point.

2) Avoid preheating and gradual cooling as much as possible. However if preheating and gradual cooling is

done, set the process conditions after confirming that the TCO is not affected by these procedures.

3) Do not use reflow soldering.

4) Thin type (MP and MU series) is not to be soldered.

5) If water or solvent is used for cleaning flux after soldering, check and confirm the reliability of the agent.

6) Lead wires are to be clamped at least 3 mm away from the seals.

Improper connections may cause damage to the seals or other parts and may result in nuisance tripping of

the devices due to the generation of excessive heat at a faulty high resistance junction.

7) Set the conditions for welding and calking only after checking contact resistance and connection strength.

8) When resoldering or rewelding, cool the TCO under room conditions.

9) When the TCO is heated by soldering or welding, be careful not to pull, push or twist the TCO lead wires.

Table-1 Soldering Conditions

3. Sufficiently flexible, appropriate free length and proper size wire should be used for splice connection. Connection

including connectors used for splicing shall be of the low resistance type, and they shall be made mechanically

secure.

4. Where the lead wires of the TCO is tied with string, put them at least 10 mm apart from the seals of the main

body of the TCO.

5. Quality control notes

1) Measurement of resistance between lead wires (terminals) and checking of the internal status with X-rays are

effective means to confirm the status of the TCO on delivery and after mounting in the equipment.

6. Storage method

1) Store the TCO in packing cases or in polyethylene bags within the temperature range -10 °C to +40 °C and

RH of 30 % to 75 %. Store them at a location where no rapid changes of temperature or humidity or no

direct sunlight is applied. The location must also be free from vibration and shock .

2) Avoid storage in places containing corrosive gases such as sea breeze, Cl2, H2S, NH3, SO2 and NO2.

3) The period of guarantee for performance such as solderability is for one year after our delivery; and this

condition applies only where the storage method specified in above has been followed.

7. Do not repair a TCO. Replace it with a new part.

Temperature of Soldering: 300 °C Time: 3 s

Lead Length (k) Type No.

30 mm F101 E101 H101

25 mm N082, N099

E115, E134, E138 H115, H134, H138

20 mm N109, N110 F115, F134,

F138, F145 E145 H145

15 mm

N127, N134, N143

● Instruction

1. Forming and Cutting

1) Lead wires(terminals) are to be bent or cut at least 3 mm away from the TCO seals to avoid damaging the

TCO (axial / radial type) or body (thin type). The TCO seals (axial / radial type) shall not be grasped with

any tools or holders. Terminals of thin type TCO are to be grasped before they are bent. (See Fig.1)

2) The lead wires and terminals shall not be nicked, fractured or burned.

The body and/or seals must not be damaged, burned or overheated.

3) It is recommended that experimental assembly trials, should be done so that it can be verified that manufacturing

procedures will not exceed the maximum tested "pull" and "push" forces of 20 N (MP series:5 N, MU series:10 N)

and 5 N respectively on the lead wires (terminals), or induce excessive twisting.

4) Do not repeat bending terminals of thin type TCO.

Jan. 201503

Safety Precautions (Common precautions for Fuses)

• When using our products, no matter what sort of equipment they might be used for, be sure to make a written

agreement on the specifications with us in advance. The design and specifications in this catalog are subject

to change without prior notice.

• Do not use the products beyond the specifications described in this catalog.

• This catalog explains the quality and performance of the products as individual components. Before use, check

and evaluate its operations when installed in your products.

• Install the following systems for a failsafe design to ensure safety if these products are to be used in equip ment

where a defect in these products may cause the loss of human life or other significant dam age, such as damage to

vehicles (automobile, train, vessel), traffic lights, medical equipment, aerospace equipment, electric heating

appliances, combustion/gas equipment, rotating equipment, and disaster/crime prevention equipment.

✽ Systems equipped with a protection circuit and a protection device

✽ Systems equipped with a redundant circuit or other system to prevent an unsafe status in the event of a sin gle fault

(1) Precautions for use

• These products are designed and manufactured for general and standard use in general elec tron ic equipment

(e.g. AV equipment, home electric appliances, office equipment, information and communication equipment)

• These products are not intended for use in the following special conditions. Before using the products,

carefully check the effects on their quality and performance, and determine whether or not they can be used.

1. In liquid, such as water, oil, chemicals, or organic solvent

2. In direct sunlight, outdoors, or in severe dust condition

3. In salty air or air with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NO2

4. Electric Static Discharge (ESD) Environment

These components are sensitive to static electricity and can be damaged under static shock (ESD).

Please take measures to avoid any of these environments.

Smaller components are more sensitive to ESD environment.

5. Electromagnetic Environment

Avoid any environment where strong electromagnetic waves exist.

6. In an environment where these products cause dew condensation

7. Sealing or coating of these products or a printed circuit board on which these products are mounted, with

resin or other materials

• These products generate Joule heat when energized. Carefully position these products so that their heat will

not affect the other components (except Thermal Cutoffs).

• Carefully position these products so that their temperatures will not exceed the category temperature range due

to the effects of neighboring heat-generating components. Do not mount or place heat-generating components

or inflammables, such as vinyl-coated wires, near these products (except Thermal Cutoffs).

• Note that non-cleaning solder, halogen-based highly active flux, or water-soluble flux may deteriorate the

performance or reliability of the products.

• Carefully select a flux cleaning agent for use after soldering. An unsuitable agent may deteriorate the performance

or reliability. In particular, when using water or a water-soluble cleaning agent, be careful not to leave water

residues. Otherwise, the insulation performance may be deteriorated.

(2) Precautions for storage

The performance of these products, including the solderability, is guaranteed for a year from the date of ar riv al

at your company, provided that they remain packed as they were when delivered and stored at a tem per a ture

of 5 °C to 35 °C and a relative humidity of 45 % to 85 %.

The performance of Thermal Cutoffs is guaranteed for a year after our delivery, provided that they are stored at a

temperature of -10 °C to +40 °C and a relative humidity of 30 % to 75 %.

Even within the above guarantee periods, do not store these products in the following conditions. Otherwise,

their electrical performance and/or solderability may be deteriorated, and the packaging materials (e.g. taping

materials) may be deformed or deteriorated, resulting in mounting failures.

1. In salty air or in air with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NO2

2. In direct sunlight

Package markings include the product number, quantity, and country of origin.

In principle, the country of origin should be indicated in English.

May. 201500

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Panasonic:

EYP-05BE101 EYP-05BE115 EYP-2BN099 EYP-2BN110 EYP-2BN143 EYP-05BE134 EYP-4MU092GFD EYP-

4MU092XU EYP-2BH115 EYP-05BE138 EYP-2BN082 EYP-2BN109 EYP-2BH145 EYP-2BN134 EYP-05BE145

EYP-1BF134 EYP-1BF138 EYP-1BF145 EYP-2BH101 EYP-2BH134 EYP-2BH138 EYP-2BN127 EYP-2MP092AU

EYP2MP092AFT EYP2MP098AFT EYP-2MP098AFT EYP-2MP092AFT EYP-2BN099L