FEATURES Miniature size No Polarity Nickel Barrier Termination Standard - highly resistant to metal migration Uniform dimensions and configuration Suitable for reflow soldering GRM39, 40 and 42-6 suitable for wave soldering Minimum series inductance Tape and Reel Packaging Bulk Case Packaging available for GRM40 and smaller Wide selection of capacitance values and voltages Largest production capacity and volume in the world PART NUMBERING SYSTEM GRM40 CAPACITOR TYPE AND SIZE See below and following pages. 3-digit code appears as necessary to indicate special thickness requirements. Please consult your local sales office for details. --- TEMPERATURE CHARACTERISTICS COG COH P2H R2H S2H T2H U2J SL COG 101 J 050 CAPACITANCE VALUE Expressed in picofarads and identified by a three-digit number. First two digits represent significant figures. Last digit specifies the number of zeros to follow. For fractional values below 10pF, the letter "R" is used as the decimal point and the last digit becomes significant. A D CAPACITANCE TOLERANCE *= Standard 5pf: B = .1pf *C = .25pf >5pf to 10pf: B = .1pf C = .25pf *D = .5pf >10pf: K = 10% *J = 5% G = 2% F = 1% VOLTAGE Identified by a three-digit number. MARKING A = Unmarked PACKAGING Reel Diameter/ Code Tape Material 7" Paper Tape D 7" Plastic Tape L 13" Paper Tape J 13" Plastic Tape K Bulk B Bulk Cassette C 7" Paper Q 2mm pitch See pages 115 -118 for labeling and packaging information. CHIP DIMENSIONS Dimensions: mm e g GRM36 GRM39* EIA Code 0402 0603 L Length 1.0 0.05 1.6 0.1 GRM40 0805 2.0 0.1 GRM42-6 1206 Size e T L W W Width 0.5 0.05 0.8 0.1 1.25 0.1 3.2 0.15 1.6 0.15 3.2 0.2 1.6 0.2 GRM42-2 1210 3.2 0.3 2.5 0.2 GRM43-2 GRM44-1 1812 2220 4.5 0.4 5.7 0.4 3.2 0.3 5.0 0.4 T Thickness 0.5 0.05 0.8 0.1 0.6 0.1 0.85 0.1 1.25 0.1 0.85 0.1 1.15 0.1 1.6 0.2 1.15 0.1 1.35 0.15 1.8 0.2 2.5 0.2 2.0 max. 2.0 max. e (min.) Termination 0.15 ~ 0.3 0.2 ~ 0.5 g (min.) Insulation 0.4 0.5 0.2 ~ 0.7 0.7 0.3 ~ 0.8 1.5 0.3 min. 1.0 0.3 min. 0.3 min. 2.0 2.0 *Bulk case packaging is L = 1.6 0.07, W, T = 0.8 0.07. CHIP TERMINATION DIAGRAMS Nickel Barrier Layer (Standard) Ceramic Dielectric Inner Electrode GRM Series Inner Termination (Ag or Ag/Pd or Cu) Nickel Plated Barrier Layer Tin Plating* *Size 0402 - Solder Plated All products on this page are available as standard through authorized Murata Electronics Distributors. CG01-J 7 SURFACE MOUNT MONOLITHIC CHIP CAPACITORS SURFACE MOUNT MONOLITHIC CHIP CAPACITORS COG AND TEMPERATURE COMPENSATING TYPES GRM36/39/40/42-6/42-2/43-2/44-1 Series SURFACE MOUNT MONOLITHIC CHIP CAPACITORS COG AND TEMPERATURE COMPENSATING TYPES - GRM36/39/40/42-6/42-2/43-2/44-1 Series SPECIFICATION GENERAL ELECTRICAL Temperature Coefficient C0G = 0 30 ppm* C0H = 0 60 ppm P2H = N150 60 ppm R2H = N220 60 ppm S2H = N330 60 ppm T2H = N470 60 ppm U2J = N750 120 ppm SL = N1000 to P350 Temperature Range -55 to +125C -55 to +125C -55 to +85C -55 to +85C -55 to +85C -55 to +85C -55 to +85C -55 to +85C *TC Tolerance for COG Refer to EIA-RS198E for other limitations TEST Capacitance & Q (Frequency & Voltage): Q Limits Insulation Resistance (I.R.) 1000pF 1MHz 100Hz @ 1.0 .2 Vrms >1000pF 1kHz 100Hz @ 1.0 .2 Vrms 30pF: 400 + (20xC (pF)) >30pF: 1000 minimum 100,000 megohms or 1000 megohms - mfd (whichever is less) with rated voltage applied for 2 minutes max with 50mA limiting current Dielectric Strength (Flash) 250% of rated voltage for 5 seconds with series resistor limiting charging current to 50mA max.; 200% for 500V Aging Negligible MECHANICAL TEST TEST METHOD Terminal Adhesion POST TEST LIMITS 0603 1.0 lbs. 0805 2.2 lbs. No evidence of termination peeling Glass Epoxy Board 10 Mounting 2n Capacitor R340 Deflection 1mm deflection (Glass epoxy board) No mechanical damage Cap., DF, IR meet initial limits Load Deflection Unit: mm 45 Capacitance meter 45 Supporter Solderability MIL-STD-202 Method 208F Contact factory for test limits TEST METHOD POST TEST LIMITS ENVIRONMENTAL TEST Thermal Shock (Air to Air) Humidity, Steady State Humidity Load MIL-STD-202, Method 107, Condition A Post thermal Shock measurement shall be taken after 24 hours stabilization. Maintain the capacitor at 40 2C and 90 to 95% humidity for 500 12 hours. Remove and let sit for 24 2 hours at room temperature, then measure. Apply the rated voltage at 40 2C and 90 to 95% humidity for 500 12 hours. Remove and let sit for 24 2 hours at room temperature, then . measure. The charge/discharge current is less than 50mA. Apply 200% of rated voltage for 1000 12 hours at maximum operating temperature; 150% for 500V. Life Test Upon completion of above test wait 24 hours prior to performing post testing. Appearance: No visual damage C: = 2.0% or 0.5pF (whichever is greater) Q: >30pF = 1,000 min., 30pF = 400 + [20 x C(pF)] I.R.: = 100,000M min. or 1,000M*F (whichever is less) Appearance: No defects Capacitance: Within 5% or .0.5pF (whichever is greater) Q/D.F.: 30pF and over: Q350; 10pf to 30pf: Q275+5/2C Q/D.F.: 10pf and below: Q20010C I.R.: 1,000M or 50M F (whichever is less) C: Nominal Capacitance (pF) Appearance: No defects Capacitance: Within 7.5% or .0.75pF (whichever is greater) Q/D.F.: 30pF and over: Q200; Q/D.F.: 30pf and below: Q10010/3C I.R.: 500M or 25M F (whichever is less) C: Nominal Capacitance (pF) Appearance: No defects Capacitance: 3% or .3pF (whichever is greater) Q: >30pF = 500 min., 30pF = 200 + [10 x C(pF)] I.R.: 1,000M or 50M F (whichever is less) Flash: 250% rated voltage STORAGE LIFE Chip component terminations should generally be protected from moisture. In addition, they should also be protected from materials containing chlorine, sulfur compounds or any harmful gases that could cause degradation of the solder. 8 1. All chip components, including tape and reel, should be kept in an area where the temperature is between 5C and 40C and where the humidity is 20% to 70%. 2. The chip components should be used within six months. 3. The solderability of the chip components should be rechecked in the event that they are not used in six months. 4. Peel strength and shelf life of tape are guaranteed for 1 year when stored under afore said conditions. CG01-J Type (EIA Code) Char. Volt. Cap. (pF) GRM36* (0402) COG COH 50 25 GRM39 (0603) COG 50 100 200 GRM40 (0805) COG COH 25 50 100 200 GRM42-6 (1206) COG COH 25 50 100 200 COH 25 0.5 0.75 1 1.5 2 3 4 5 6 7 8 9 10 11 12 13 15 16 18 20 22 24 27 30 33 36 39 43 47 51 56 62 68 75 82 91 100 110 120 130 150 160 180 200 220 240 270 300 330 360 390 430 470 510 560 620 680 750 820 910 1000 1100 1200 1300 1500 1600 1800 2000 2200 2400 2700 3000 3300 3600 3900 4300 4700 5100 5600 6200 6800 7500 8200 9100 10000 11000 12000 13000 15000 16000 Note: Capacitance values = EIA 24 Step = 10, 11, 12, 13, 15, 16, 18, 20, 22, 24, 27, 30, 33, 36, 39, 43, 47, 51, 56, 62, 68, 75, 82, 91 *GRM36 is suited to only reflow soldering. THICKNESS AND PACKAGING TYPES/QUANTITY Type GRM36 GRM39 GRM40 CG01-J Thickness: T Bulk Taping Bulk Case Thickness: T Bulk Taping Bulk Case Type (mm) (pcs./bag) (pcs./178mm reel)1 (pcs./case) (mm) (pcs./bag) (pcs./178mm reel)1 (pcs./case) : 0.5 0.05 1000 10000 50000 : 0.85 0.1 1000 4000 -- GRM42-6 : 0.8 0.12 1000 4000 15000 : 1.15 0.1 1000 3000 -- : 0.6 0.1 1000 4000 10000 : 0.85 0.1 1000 4000 -- 1 330mm reel is available on request. 2Bulk case packaging is T = 0.8 0.07. : 1.25 0.1 1000 3000 5000 9 SURFACE MOUNT MONOLITHIC CHIP CAPACITORS SURFACE MOUNT MONOLITHIC CHIP CAPACITORS COG/COH TYPE-25V/50V/100V/200V GRM36/39/40/42-6 Series SURFACE MOUNT MONOLITHIC CHIP CAPACITORS COG TYPE-50V/100V/200V GRM42-2/43-2/44-1 Series Type (EIA Code) Char. Volt. Cap. (pF) GRM42-2 (1210) COG 50 100 GRM43-2 (1812) COG 200 50 100 GRM44-1 (2220) COG 200 50 100 200 130 150 160 180 200 220 240 270 300 330 360 390 430 470 510 560 620 680 750 820 910 1000 1100 1200 1300 1500 1600 1800 2000 2200 2400 2700 3000 3300 3600 3900 4300 4700 5100 5600 6200 6800 7500 8200 9100 10000 11000 12000 13000 15000 16000 18000 20000 22000 24000 27000 30000 33000 36000 39000 43000 47000 Note: Capacitance values = EIA 24 Step = 10, 11, 12, 13, 15, 16, 18, 20, 22, 24, 27, 30, 33, 36, 39, 43, 47, 51, 56, 62, 68, 75, 82, 91 THICKNESS AND PACKAGING TYPES/QUANTITY Type GRM42-2 GRM43-2 GRM44-1 Thickness: T (mm) : 1.35 0.15 : 2.0 max. : 2.0 max. Bulk (pcs./bag) Taping (pcs./178mm reel)* 1000 1000 1000 2000 1000 1000 *330mm reel is available on request. 10 CG01-J Type (EIA Code) Char. Volt. Cap. (pF) GRM36* (0402) SL 25 50 SL 25 50 GRM36/39 Series P2H GRM39 (0603) R2H S2H T2H U2J 50 50 50 50 50 0.5 0.75 1 1.5 2 3 4 5 6 7 8 9 10 11 12 13 15 16 18 20 22 24 27 30 33 36 39 43 47 51 56 62 68 75 82 91 100 110 120 130 150 160 180 200 220 240 270 300 330 360 390 430 470 510 560 620 680 750 820 910 1000 1100 1200 1300 1500 1600 1800 2000 2200 2400 2700 3000 3300 3600 3900 4300 4700 5100 5600 6200 6800 7500 8200 9100 10000 11000 12000 13000 15000 16000 Note: Capacitance values = EIA 24 Step = 10, 11, 12, 13, 15, 16, 18, 20, 22, 24, 27, 30, 33, 36, 39, 43, 47, 51, 56, 62, 68, 75, 82, 91 *GRM36 is suited to only reflow soldering. THICKNESS AND PACKAGING TYPES/QUANTITY Thickness: T (mm) Type Bulk Taping Bulk Case (pcs./bag) (pcs./178mm reel)1 (pcs./case) GRM36 : 0.5 0.05 1000 10000 50000 GRM39 : 0.8 0.12 1000 4000 15000 1 330mm reel is available on request. 2Bulk case packaging is T = 0.8 0.07. CG01-J 11 SURFACE MOUNT MONOLITHIC CHIP CAPACITORS SURFACE MOUNT MONOLITHIC CHIP CAPACITORS TEMPERATURE COMPENSATING TYPE-25V/50V SURFACE MOUNT MONOLITHIC CHIP CAPACITORS TEMPERATURE COMPENSATING TYPE-25V/50V Type (EIA Code) Char. Volt. Cap. (pF) SL 25 P2H 50 50 GRM40 (0805) R2H S2H 50 T2H U2J 50 50 50 GRM42-6 (1206) P2H R2H S2H SL 25 GRM40/42-6 Series 50 50 50 50 T2H U2J 50 50 0.5 0.75 1 1.5 2 3 4 5 6 7 8 9 10 11 12 13 15 16 18 20 22 24 27 30 33 36 39 43 47 51 56 62 68 75 82 91 100 110 120 130 150 160 180 200 220 240 270 300 330 360 390 430 470 510 560 620 680 750 820 910 1000 1100 1200 1300 1500 1600 1800 2000 2200 2400 2700 3000 3300 3600 3900 4300 4700 5100 5600 6200 6800 7500 8200 9100 10000 11000 12000 13000 15000 16000 Note: Capacitance values = EIA 24 Step = 10, 11, 12, 13, 15, 16, 18, 20, 22, 24, 27, 30, 33, 36, 39, 43, 47, 51, 56, 62, 68, 75, 82, 91 THICKNESS AND PACKAGING TYPES/QUANTITY Type GRM40 12 Thickness: T Bulk Taping Bulk Case Thickness: T Bulk Taping Bulk Case Type (mm) (pcs./bag) (pcs./178mm reel)* (pcs./case) (mm) (pcs./bag) (pcs./178mm reel)* (pcs./case) : 0.6 0.1 1000 4000 10000 : 0.85 0.1 1000 4000 -- GRM42-6 : 0.85 0.1 1000 4000 -- : 1.15 0.1 1000 3000 -- *330mm reel is available on request. : 1.25 0.1 1000 3000 5000 CG01-J