NUMBER 110-435G TYPE
PRODUCT SPECIFICATION
TITLE PAGE REVISION
1 of 10 B
AUTHORIZED BY DATE
0.5mm Pitch FPC/FFC Connector
62674-_ _ 11_1ALF Sei Watanabe 2010-5-19
CLASSIFICATION
UNRESTRICTED
Copyright FCI
Form E-3334
Rev F
GS-01-001
Table of Contents
1 SCOPE ………………….………………….……………………………………………………………………3
2 APPLICABLE STANDARDS ….…..…………………………………..………………………………………3
3 CATALOG NO. STRUCTURE ……………………………………………………………………………..3
4 CONNECTOR SHAPE, DIMENSIONS AND MARTERIALS ….………………………………………….3
5 ACCOMMODATED CONDUCTORS (FPC/FFC) ……………………………..……………………………...3
6 PACKAGING CONDITION …………………………………………..…… …....……………………………...3
7 RECOMMENDED MOUNTING PATTERN DIMENSIONS …………..…………………………………...3
8 RATING ………………………………………………………………………………………………………..4
8-1 Voltage ……….…………..……………………………………………………………………………...4
8-2 Current ………………………………………………………………….………………………………….4
8-3 Operating Temperature …..……………..……….………..……….….……………………………….4
9 PERFORMANCE CHARACTERISTICS ……………………………………………..……………………..4
9-1 Electrical Performance ……..…………………………………………………………………………...4
9-1-1 Contact resistance ……..………………………………………………..…….………………...4
9-1-2 Insulation resistance …………………….……………..……………..…….…….……………...5
9-1-3 Dielectric withstanding voltage ………..…………….……………………...………………...5
9-2 Mechanical Performance ………………………………….…….………...…………………………….5
9-2-1 Durability (Slider operation) …………….….….…………..…………………..……………...5
9-2-2 Vibration (Sinusoidal) ……..………………….….…………..…………..……..……………...5
NUMBER 110-435G TYPE
PRODUCT SPECIFICATION
TITLE PAGE REVISION
2 of 10 B
AUTHORIZED BY DATE
0.5mm Pitch FPC/FFC Connector
62674-_ _ 11_1ALF Sei Watanabe 2010-5-19
CLASSIFICATION
UNRESTRICTED
Copyright FCI
Form E-3334
Rev F
GS-01-001
9-3 Environmental Performance …..……………..……….……….…………………..………………….6
9-3-1 Damp heat (Steady state) …..……………………..………..……….………..…….………….6
9-3-2 Salt spray …………………………………………..……….…………….……………………….6
9-3-3 Change of temperature …..…………….………………..….…………..……….….………….7
9-4 Other performance …..…………..……..……….……………..….………..……..…………………….7
9-4-1 Soldering (Resistance to reflow soldering) ……..…………………………..…………….…….7
9-4-2 Soldering (Solderability) (Reflow) ……………...…………….………………..………………….8
10 INDICATION AND PACKAGING …………………………..……….…………..….……………………….9
10-1 Indication ……..………..………………………..……………………………….………………….9
10-2 Packaging …………………....…………………..…………………………………………………9
11 REMARKS ………………………………………………………………………………..……………………..9
12 RECOMMENDED REFLOW PROFILE ………………………………………………………………………9
13 REVISION RECORD ………………………………………………………………………………………10
NUMBER 110-435G TYPE
PRODUCT SPECIFICATION
TITLE PAGE REVISION
3 of 10 B
AUTHORIZED BY DATE
0.5mm Pitch FPC/FFC Connector
62674-_ _ 11_1ALF Sei Watanabe 2010-5-19
CLASSIFICATION
UNRESTRICTED
Copyright FCI
Form E-3334
Rev F
GS-01-001
1. SCOPE
This specification covers the requirements for the connector with 0.5mm spacing to which the edge of
FPC(Flexible Printed Circuit) and FFC(Flexible Flat Cable) can be connected by Zero-Insertion-Force
method and which copes with automatic mounting and SMT.
2. APPLICABLE STANDARDS
JIS
C
5402 Method for Test of Connectors for Electronic Equipment
JIS
C
0806 Packing of Electronic Components on Continuous Tapes
(Surface Mount Components)
UL – 94 TESTS FOR FLAMMABILITY OF PLASTIC MATERIALS FOR PARTS IN
DEVICES AND APPLIANCES.
3. CATALOG No. STRUCTURE
62674 - 20 1 1 2 1 A LF
Series
Number of Contacts
Contact direction
SMT
Variation
2 : Foot Pattern A
Packaging
0 : Connector
1 : Plastic Tape Packaging
Gold Plating
Lead Free
4. CONNECTOR SHAPE, DIMENSIONS AND MATERIALS
See attached drawings.
5. ACCOMMODATED CONDUCTORS (FPC/FFC)
See attached drawings.
6. PACKAGING CONDITION
See attached drawings.
7. RECOMMENDED MOUNTING PATTERN DIMENSIONS
See attached drawings.
NUMBER 110-435G TYPE
PRODUCT SPECIFICATION
TITLE PAGE REVISION
4 of 10 B
AUTHORIZED BY DATE
0.5mm Pitch FPC/FFC Connector
62674-_ _ 11_1ALF Sei Watanabe 2010-5-19
CLASSIFICATION
UNRESTRICTED
8. RATING
8-1. Voltage : A.C.50V D.C.50V
8-2. Current : A.C.0.5A D.C.0.5A (Refer to the following note.)
8-3. Operating Temperature : -55°C ~ +105°C (Including terminal temperature rises)
NOTE
Allowable maximum current for one contact is 0.5A. Total allowable current for a whole connector
is the value which is shown in the following figure.
4
3
2
1
Total
Current
(A)
0
2
4
6
8 10
12
14
16
18 20
22
24
26
28
30
32
34 36 38 40
Number of contacts
9. PERFORMANCE CHARACTERISTICS
9-1. Electrical Performance
No. Test Item Test Method Requirements
9-1-1 Contact
resistance
1) Measure contact resistance between V1-V2
by voltage drop method by the following
circuit by mating accommodated conductor
specified in clause 5 after reflow soldering
the connector on the P.CB.
Soldering
portion
Connector
P.C.B.
Pattern
Conductor
2) Open circuit voltage : Less than A.C.20mV
3) Test current : Less than A.C.20mA
1) Initial value
: Less than 30mΩ
2) Contact resistance after the
test is in accordance with the
value specified in each test
item.
Copyright FCI
Form E-3334
Rev F
GS-01-001
NUMBER 110-435G TYPE
PRODUCT SPECIFICATION
TITLE PAGE REVISION
5 of 10 B
AUTHORIZED BY DATE
0.5mm Pitch FPC/FFC Connector
62674-_ _ 11_1ALF Sei Watanabe 2010-5-19
CLASSIFICATION
UNRESTRICTED
Copyright FCI
Form E-3334
Rev F
GS-01-001
9-1-2 Insulation
resistance
1) Measure insulation resistance between
adjacent contacts in a connector individual.
2) Test voltage : D.C.500V
3) Read value one minute after applying test
voltage.
1) More than 100MΩ
9-1-3
Dielectric
withstanding
voltage
1) For one minute, apply A.C.200V between
adjacent contacts in a connector individual.
2) Set current : A.C.1mA
1) Free from any short circuit
and insulation breakdown.
9-2. Mechanical Performance
No. Test Item Test Method Requirements
9-2-1
Durability
(Slider
operation)
1) Measure contact resistance before and after
the test by the method in clause 9-1-1 by
mating the accommodated conductor
specified in clause 5.
2) Number of slider open and close : 20 times
(Insert and extract the conductor for each
opening of the slider.)
1) Initial contact resistance
: Less than 30mΩ
2) Contact resistance after the
test : Less than 50mΩ
3) Free from any defect such as
break etc. on the connector
and conductor.
9-2-2 Vibration
(Sinusoidal)
JIS C 60068-2-6 (IEC60068-2-6)
1) Frequency range : 10 ~ 500Hz
2) Amplitude : 0.75mm
or Acceleration : 100m/s2
3)Sweep rate : 1 octave/minute
4)Kind of test : Sweep endurance test
5)Test time : 10 cycles
1) During the test, no circuit
opening for more than 1µs.
2) Free from any defect such as
break, deformation, loosing
and falling off etc. on each
portion of the connector.
NUMBER 110-435G TYPE
PRODUCT SPECIFICATION
TITLE PAGE REVISION
6 of 10 B
AUTHORIZED BY DATE
0.5mm Pitch FPC/FFC Connector
62674-_ _ 11_1ALF Sei Watanabe 2010-5-19
CLASSIFICATION
UNRESTRICTED
Copyright FCI
Form E-3334
Rev F
GS-01-001
9-3. Environmental Performance
No. Test Item Test Method Requirements
9-3-1 Damp heat
(Steady state)
JIS C 60068-2-78 (IEC60068-2-78)
1) Measure contact resistance before and after
the test by the method in clause 9-1-1 by
using the accommodated conductor
specified in clause 5.
2) Measure insulation resistance after the test
by the method in clause 9-1-2.
3) Bath temperature : 40°C
4) Bath humidity : 90 ~ 95%(
relative humidity
)
5) Period of exposure : 48 hours
6) Expose conductor and connector in mated
condition and leave them under normal
temperature.
(Without insertion and separation)
1) Initial contact resistance
: Less than 30mΩ
2) Contact resistance after the
test : Less than 50mΩ
3) Insulation resistance after
the test : More than 100MΩ
9-3-2 Salt spray
JIS C 60068-2-11 (IEC60068-2-11)
1) Measure contact resistance before and after
the test according to the method in clause
9-1-1 by using accommodated conductor
specified in clause 5.
2) Salt solution concentration : 5%
3) Period of exposure : 48 hours
4) Expose conductor and connector in mated
condition and leave them under normal
temperature after posttreatment. (24 hours)
1) Initial contact resistance
: Less than 30mΩ
2) Contact resistance after the
test : Less than 50mΩ
NUMBER 110-435G TYPE
PRODUCT SPECIFICATION
TITLE PAGE REVISION
7 of 10 B
AUTHORIZED BY DATE
0.5mm Pitch FPC/FFC Connector
62674-_ _ 11_1ALF Sei Watanabe 2010-5-19
CLASSIFICATION
UNRESTRICTED
Copyright FCI
Form E-3334
Rev F
GS-01-001
9-3-3 Change of
temperature
JIS C 0025 (IEC60068-2-14)
1) Measure contact resistance before and after
the test according to the method in clause
9-1-1 by using accommodated conductor
specified in clause 5.
2) One cycle of temperature is as follow and
test 5 cycles.
3) Expose conductor and connector in mated
condition and leave them under normal
temperature.
1) Initial contact resistance
: Less than 30mΩ
2) Contact resistance after the
test : Less than 50mΩ
3) Free from any defect such
as crack, warping and
deformation etc. on each
portion the connector.
Step Temp.(°C) Time(min.)
1 -55±3 30
2 25±2 2 ~ 3
3 85±2 30
4 25±2 2 ~ 3
9-4. Other performance
No. Test Item Test Method Requirements
JIS C 60068-2-58 (IEC60068-2-58)
1) Solder by setting reflow bath on the
following condition.
2) Preheating：150~180°C, 120±5 s
3) Soldering
：220°C min. 60s max.
4) Peak
：245°C min. 20s max.
(Peak 255°C max.)
NOTE： Temperature must be measured at
contact terminal portion and peak
temperature on the upper surface of
P.C.B must be less than 260°C.
5) Solder paste to be used is JIS Z 3282
Sn96.5Ag3.0Cu0.5
1) Contact resistance after the
test : Less than 50mΩ
2) Insulation resistance after
the test : More than 100MΩ
3) No short circuit and
insulation breakdown for
dielectric withstanding
voltage test after this test.
4) Free from any damage on
performance and contact
performance after soldering.
9-4-1
Soldering
(Resistance to
reflow
soldering)
Diagram A
NUMBER 110-435G TYPE
PRODUCT SPECIFICATION
TITLE PAGE REVISION
8 of 10 B
AUTHORIZED BY DATE
0.5mm Pitch FPC/FFC Connector
62674-_ _ 11_1ALF Sei Watanabe 2010-5-19
CLASSIFICATION
UNRESTRICTED
Copyright FCI
Form E-3334
Rev F
GS-01-001
JIS C 60068-2-58 (IEC60068-2-58)
1) Solder by setting reflow bath on the
following condition.
2) Preheating：150~180°C, 60~120s
3) Soldering
：225°C min., 20±5s
(Peak 235°C max.)
NOTE： Temperature must be measured at
contact terminal portion and peak
temperature on the upper surface of
P.C.B must be less than 260°C.
4) Solder paste to be used is JIS Z 3282
Sn96.5Ag3.0Cu0.5
1) Actual soldered area must be
more than 90% of the dipped
area intended to be soldered.
9-4-2
Soldering
(Solderability)
(Reflow)
Diagram B
NUMBER 110-435G TYPE
PRODUCT SPECIFICATION
TITLE PAGE REVISION
9 of 10 B
AUTHORIZED BY DATE
0.5mm Pitch FPC/FFC Connector
62674-_ _ 11_1ALF Sei Watanabe 2010-5-19
CLASSIFICATION
UNRESTRICTED
Copyright FCI
Form E-3334
Rev F
GS-01-001
10. INDICATION AND PACKAGING
10-1. Indication
1) Catalog number and lot number are not be indicated on the connector.
2) Catalog number and quantity shall be indicated on the surface of the package box.
10-2. Packaging
1) The connector individuals are packed by tapes with specified quantity in accordance with
[JIS C 0806 "Packaging of Electronic Components on Continuous Tapes (Surface Mount
components)" ] and put into package box in accordance with FCI
JAPAN packaging
specification.
11. REMARKS
11-1. Please use for gold plating cable as accommodated conductor.
12. RECOMMENDED REFLOW PROFILE
Diagram C. Recommended reflow temperature profile
Note: Please check the reflow soldering condition for your own application beforehand
due to different conditions with soldering devices, P.C. Boards, etc.
No moisture treatment before reflow process.
NUMBER 110-435G TYPE
PRODUCT SPECIFICATION
TITLE PAGE REVISION
10 of 10 B
AUTHORIZED BY DATE
0.5mm Pitch FPC/FFC Connector
62674-_ _ 11_1ALF Sei Watanabe 2010-5-19
CLASSIFICATION
UNRESTRICTED
Copyright FCI
Form E-3334
Rev F
GS-01-001
13. REVISION RECORD
REV. PAGE DESCRIPTION ECR# DATE
A ALL RELEASE J05-0353 2005-6-15
B ALL Form Change
Operating temperature to -55 ~ 105°C
ECR-EXL-J
-003824 2010-5-19
