G3MC-101PL-VD-DC12 - Omron - Datasheet.Directory

Solid State Relay G3MC 401

Solid State Relay

G3MC

Compact, Thin-profile, Low-cost SSR with

Reinforced Insulation

• Small bottom surface area (approx. 80% of the

conventional G3MB’s), ideal for close PCB mounting.

•

DC input and AC output for an applicable load of 1A at 40°C

• Compact, thin-profile SSR of monoblock construction with

an all-in-one frame incorporates a PCB, terminals, and a

heatsink.

• Approved by UL and CSA. VDE certified models available.

• Models with reinforced insulation are available.

Ordering Information

To Order: Select the part number and add the desired coil voltage rating, (e.g., G3MC-101P-DC12).

Note: 1. All models meet UL and CSA standards. In order to obtain VDE approved versions with UL, CSA and VDE Logos, add “-VD” to the part

number. Example: G3MC-101P-VD-DC12

2. 2A models are available with reinforced insulation. Add “-1” to the part number to obain 2A models with reinfored insulation.

Examples: G3MC-202PL-1-DC5 G3MC-202P-VD-1-DC24

Isolation Zero-cross function Built-in snubber circuit Rated output load Rated input voltage Part number

Phototriac Yes Yes 1 A at 100 to 120 VAC

(75 to 132 VAC)

5 VDC G3MC-101P

12 VDC

24 VDC

No 5 VDC G3MC-101PL

12 VDC

24 VDC

Yes 2 A at 100 to 240 VAC

(75 to 264 VAC)

5 VDC G3MC-202P

12 VDC

24 VDC

No 5 VDC G3MC-202PL

12 VDC

24 VDC

402 Solid State Relay G3MC

Specifications

■Ratings (Ambient temperature 25°C)

Input

Note: Each model has 5-VDC, 12-VDC, and 24-VDC input versions.

Output

■Characteristics

Rated voltage Operating voltage Impedance Voltage levels

Must operate voltage Must dropout voltage

5 VDC 4 to 6 VDC 300Ω ±20% 4 VDC max. 1 VDC min.

12 VDC 9.6 to 14.4 VDC 800Ω ±20% 9.6 VDC max.

24 VDC 19.2 to 28.8 VDC 1.6kΩ ±20% 19.2 VDC max.

Part number Applicable load

Rated load voltage Load voltage range Load current Surge current

G3MC-101P(L)(-VD) 100 to 120 VAC, 50/60 Hz 75 to 132 VAC, 50/60 Hz 0.1 to 1 A 8 A (60 Hz, 1 cycle)

G3MC-202P(L)(-VD)(-1) 100 to 240 VAC, 50/60 Hz 75 to 264 VAC, 50/60 Hz 0.1 to 2 A 30 A (60 Hz, 1 cycle)

Item G3MC-101P(-VD) G3MC-101PL(-VD) G3MC-202P(-VD)(-1) G3MC-202PL(-VD)(-1)

Operate time 1/2 of load power source

cycle + 1 ms

1 ms max. 1/2 of load power source

cycle + 1 ms

1 ms max.

Release time 1/2 of load power source cycle + 1 ms)

Output ON voltage drop 1.6 V (RMS) max.

Leakage current 1 mA max. (at 100 VAC) 1.5 mA max. (at 200 VAC)

Insulation resistance 1,000 MΩ min. (at 500 VDC)

Dielectric strength 2,500 VAC, 50/60 Hz for 1 min (3,000 VAC, 50/60 Hz for 1 min. for G3MC-@@@-VD-1)

Vibration resistance Malfunction: 10 to 55 Hz, 0.75-mm double amplitude

Shock resistance Malfunction: 1,000 m/s2 (approx. 100G)

Ambient temperature Operating:–30°C to 80°C (with no icing or condensation)

Storage:–30°C to 100°C (with no icing or condensation)

Approved standards UL File No. E64562, CSA File No. LR35535

EN60950 File No. 5925UG (“-VD(-1)” type)

Ambient humidity Operating: 45% to 85%

Weight Approx. 2.5g (Approx. 5g for G3MC-202P(L)-VD-1)

Solid State Relay G3MC 403

Engineering Data

■G3MC-101P(L)(-VD)

■G3MC-202P(L)(-VD)(-1)

Peak inrush current (A)

Energized time (ms)

1.2

1.0

0.8

0.6

0.4

0.2

0100806040200−20−30

Load current (A)

Ambient temperature (°C)

Load Current vs. Ambient

Temperature Characteristics

Inrush Current Resistivity

One cycle, non-repetitive (Keep the inrush current

to half the rated value if it occurs repeatedly.)

2.5

2.0

1.5

1.0

0.5

010080604020 250−20−30

Load current (A)

Ambient temperature (°C)

Load Current vs. Ambient

Temperature Characteristics

Inrush Current Resistivity

One cycle, non-repetitive (Keep the inrush current

to half the rated value if it occurs repeatedly.)

Peak inrush current (A)

Energized time (ms)

404 Solid State Relay G3MC

Dimensions

Units: mm (inch)

G3MC-202P(L)(-VD)(-1)

G3MC-101P(L)(-VD)

0.8

3.5

2.54

2.54 0.25

1.2

4-1.6 4-0.7

7.6210.16

0.8

3.5

2.54

2.54 0.25

1.2

4-1.6 4-0.7

7.6210.16

13.5 max.

24.5 max.

4.5 max. Four, 1.0-dia. holes

Four, 1.0-dia. holes

4.5 max.

20.5 max.

24.5 max.

PCB Dimensions

(Bottom View)

PCB Dimensions

(Bottom View)

Terminal Arrangement

(Bottom View)

Terminal Arrangement

(Bottom View)

Solid State Relay G3MC 405

Precautions

■General Precautions

Do not touch the terminals of the SSR while power is being supplied

to the SSR. The terminals are charged with the power,

and an electric shock may be received by touching the terminals.

The built-in capacitor may have a residual voltage after the SSR

is turned off. Be sure to discharge the residual voltage before touch-

ing the terminals of the SSR, otherwise an electric shock

may be received.

■Mounting

1. Make sure that no excessive voltage or current is imposed on or

flows to the input or output circuit of the SSR,

otherwise the SSR may malfunction or burn.

2. Solder the terminals of the SSR properly under the required sol-

dering conditions. The SSR may be abnormally heated and burn

if power is supplied to the terminals soldered incorrectly.

3. Do not short-circuit the load of the SSR while power is supplied to

the SSR. Do not short-circuit the power supply through the SSR.

The SSR may be damaged, malfunction, or burn if the load or

power supply is short-circuited.

■Correct use

The terminals of the SSR are highly heat-conductive. Each terminal

must be soldered within 10 s at 260°C or within 5 s at 350°C.

The SSR is of a thin-profile construction. To maintain the vibration

resistance of the SSR, make sure that the space between the SSR

and PCB is 0.1 mm maximum. Lifting of the PCB can be prevented

by setting the hole diameter of the PCBs on both sides slightly

smaller than the actual terminal dimension.

Select the model without the zero-cross function when using the Unit

for phase control output.

The casing works as a heat sink. When mounting two or more Units

closely, make sure that the Units are properly ventilated by taking

ambient temperature rises into consideration. If Units are closely

mounted and used in places with no ventilation, the load current of

each Unit must be 1/2 of the rated load current.

■Protective element

No overvoltage absorption element is built in. Therefore, if the G3MC

is connected to an inductive load, be sure to connect the overvoltage

absorption element.

G3MC-@@@PL (without Zero cross function)

G3MC-@@@P (with Zero cross function)

Phototriac

Input

Load

Protective

element

(MOV)

Power

supply

Phototriac

Input

Load

Protective

element

(MOV)

Power

supply

Solid State Relay G3MC

OMRON ON-LINE

Global - http://www.omron.com

USA - http://www.components.omron.com

Cat. No. X301-E-1b Printed in USA

OMRON ELECTRONIC

COMPONENTS LLC

55 E. Commerce Drive, Suite B

Schaumburg, IL 60173

847-882-2288

09/11 Specifications subject to change without notice

All sales are subject to Omron Electronic Components LLC standard terms and conditions of sale, which

can be found at http://www.components.omron.com/components/web/webfiles.nsf/sales_terms.html

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.