MC7800, MC7800A, NCV7805 1.0 A Positive Voltage Regulators These voltage regulators are monolithic integrated circuits designed as fixed- voltage regulators for a wide variety of applications including local, on-card regulation. These regulators employ internal current limiting, thermal shutdown, and safe-area compensation. With adequate heatsinking they can deliver output currents in excess of 1.0 A. Although designed primarily as a fixed voltage regulator, these devices can be used with external components to obtain adjustable voltages and currents. *Output Current in Excess of 1.0 A *No External Components Required *Internal Thermal Overload Protection *Internal Short Circuit Current Limiting *Output Transistor Safe-Area Compensation *Output Voltage Offered in 2% and 4% Tolerance *Available in Surface Mount D2PAK-3, DPAK-3 and Standard 3-Lead Transistor Packages *NCV Prefix for Automotive and Other Applications Requiring Site and Control Changes *Pb-Free Packages are Available Value Rating Input Voltage Symbol (5.0 - 18 V) (24 V) Power Dissipation VI PD TO-220-3 T SUFFIX CASE 221AB 1 2 Heatsink surface connected to Pin 2. 3 Pin 1. Input 2. Ground 3. Output 1 D2PAK-3 D2T SUFFIX CASE 936 3 Heatsink surface (shown as terminal 4 in case outline drawing) is connected to Pin 2. 4 DPAK-3 DT SUFFIX CASE 369C 1 2 3 STANDARD APPLICATION MAXIMUM RATINGS (TA = 25C, unless otherwise noted) 369C 221A http://onsemi.com Unit Input Vdc Cin* 0.33 mF 936 35 40 Internally Limited W Thermal Resistance, Junction-to-Ambient RqJA 92 65 Figure 14 C/W Thermal Resistance, Junction-to-Case RqJC 5.0 5.0 5.0 C/W Storage Junction Temperature Range Tstg Operating Junction Temperature TJ C -65 to +150 C +150 Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. *This device series contains ESD protection and exceeds the following tests: Human Body Model 2000 V per MIL_STD_883, Method 3015. Machine Model Method 200 V. MC78XX Output CO** A common ground is required between the input and the output voltages. The input voltage must remain typically 2.0 V above the output voltage even during the low point on the input ripple voltage. XX, These two digits of the type number indicate nominal voltage. * Cin is required if regulator is located an appreciable distance from power supply filter. ** CO is not needed for stability; however, it does improve transient response. Values of less than 0.1 mF could cause instability. ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 22 of this data sheet. DEVICE MARKING INFORMATION See general marking information in the device marking section on page 29 of this data sheet. (c) Semiconductor Components Industries, LLC, 2007 May, 2007 - Rev. 17 1 Publication Order Number: MC7800/D MC7800, MC7800A, NCV7805 Vin MC7800 R24 50 D2 Zener LAT 3 A Q18 LAT Q17 Q19 QNPN C3 R19 27.5 k Q20 QNPN 1.0 P R14 1.0 k Q10 QNPN R18 100 k R21 600 R22 100 Q7 QNPN R15 680 R23 0.2 Vout 5.01 Q5 QNPN 2 R17 9.0 k R11 15 k Q6 QNPN D1 Zener R30 18 k Q12 QNPN Q9 QNPN 2 Q15 QNPN R1 10.66 k R16 600 R20 17500 Q8 QNPN R2 1.56 k Q1 C2 3.0 P R10 3340-(3316ACT) R9 3.0 k R5 4.5 k Q14 QNPN Sense N+ QNPN 6 SUB Q11 2 C1 30 P Q4 QNPN Q13 QNPN Q3 QNPN Q2 Q16 QNPN 4 Diode R6 1.0 k R7 14 k R3 1.8 k R8 5.0 k This device contains 22 active transistors. Figure 1. Representative Schematic Diagram http://onsemi.com 2 R12 3.0 k R29 9.0 k R25 6.0 k R28 9.0 k R26 3.0 k R27 9.0 k R13 11660 MC7800, MC7800A, NCV7805 ELECTRICAL CHARACTERISTICS (Vin = 10 V, IO = 500 mA, TJ = Tlow to Thigh (Note 1), unless otherwise noted) MC7805B, NCV7805 Characteristic MC7805C Symbol Min Typ Max Min Typ Max Unit Output Voltage (TJ = 25C) VO 4.8 5.0 5.2 4.8 5.0 5.2 Vdc Output Voltage (5.0 mA IO 1.0 A, PD 15 W) 7.0 Vdc Vin 20 Vdc 8.0 Vdc Vin 20 Vdc VO 4.75 5.0 5.25 4.75 - 5.0 - 5.25 - 5.0 1.3 100 50 - 0.5 0.8 20 10 - 1.3 0.15 100 50 - 1.3 1.3 25 25 - 3.2 8.0 - 3.2 6.5 - - 0.5 - 0.3 0.08 1.0 0.8 Line Regulation (Note 4) 7.5 Vdc Vin 20 Vdc, 1.0 A 8.0 Vdc Vin 12 Vdc Regline Load Regulation (Note 4) 5.0 mA IO 1.0 A 5.0 mA IO 1.5 A (TA = 25C) Regload Quiescent Current Vdc - IB mV mV mA Quiescent Current Change 7.0 Vdc Vin 25 Vdc 5.0 mA IO 1.0 A (TA = 25C) DIB Ripple Rejection 8.0 Vdc Vin 18 Vdc, f = 120 Hz RR - 68 - 62 83 - dB VI - VO - 2.0 - - 2.0 - Vdc Output Noise Voltage (TA = 25C) 10 Hz f 100 kHz Vn - 10 - - 10 - mV/VO Output Resistance f = 1.0 kHz rO - 0.9 - - 0.9 - mW Short Circuit Current Limit (TA = 25C) Vin = 35 Vdc ISC - 0.2 - - 0.6 - A Peak Output Current (TJ = 25C) Imax - 2.2 - - 2.2 - A TCVO - -0.3 - - -0.3 - mV/C Dropout Voltage (IO = 1.0 A, TJ = 25C) Average Temperature Coefficient of Output Voltage mA 1. Tlow = 0C for MC78XXAC, C, Thigh = +125C for MC78XXAC, NCV7805 = *40C for MC78XXB, MC78XXAB, NCV7805 2. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. http://onsemi.com 3 MC7800, MC7800A, NCV7805 ELECTRICAL CHARACTERISTICS (Vin = 10 V, IO = 1.0 A, TJ = Tlow to Thigh (Note 3), unless otherwise noted) MC7805AB/MC7805AC Characteristic Symbol Min Typ Max Unit Output Voltage (TJ = 25C) VO 4.9 5.0 5.1 Vdc Output Voltage (5.0 mA IO 1.0 A, PD 15 W) 7.5 Vdc Vin 20 Vdc VO 4.8 5.0 5.2 Vdc Line Regulation (Note 4) Regline mV 7.5 Vdc Vin 25 Vdc, IO = 500 mA - 0.5 10 8.0 Vdc Vin 12 Vdc, IO = 1.0 A - 0.8 12 8.0 Vdc Vin 12 Vdc, IO = 1.0 A, TJ = 25C - 1.3 4.0 7.3 Vdc Vin 20 Vdc, IO = 1.0 A, TJ = 25C - 4.5 10 Load Regulation (Note 4) Regload mV 5.0 mA IO 1.5 A, TJ = 25C - 5.0 mA IO 1.0 A 250 mA IO 750 mA Quiescent Current IB 1.3 25 - 0.8 25 - 0.53 15 - 3.2 6.0 DIB Quiescent Current Change mA 8.0 Vdc Vin 25 Vdc, IO = 500 mA - 0.3 0.8 7.5 Vdc Vin 20 Vdc, TJ = 25C - - 0.8 5.0 mA IO 1.0 A mA - 0.08 0.5 RR 68 83 - dB VI - VO - 2.0 - Vdc Output Noise Voltage (TA = 25C) 10 Hz f 100 kHz Vn - 10 - mV/VO Output Resistance (f = 1.0 kHz) rO - 0.9 - mW Short Circuit Current Limit (TA = 25C) Vin = 35 Vdc ISC - 0.2 - A Peak Output Current (TJ = 25C) Imax - 2.2 - A TCVO - -0.3 - mV/C Ripple Rejection 8.0 Vdc Vin 18 Vdc, f = 120 Hz, IO = 500 mA Dropout Voltage (IO = 1.0 A, TJ = 25C) Average Temperature Coefficient of Output Voltage 3. Tlow = 0C for MC78XXAC, CThigh = +125C for MC78XXAC, C, NCV7805 = *40C for MC78XXB, MC78XXAB, NCV7805 4. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. http://onsemi.com 4 MC7800, MC7800A, NCV7805 ELECTRICAL CHARACTERISTICS (Vin = 11 V, IO = 500 mA, TJ = Tlow to Thigh (Note 5), unless otherwise noted) MC7806B Characteristic MC7806C Symbol Min Typ Max Min Typ Max Unit Output Voltage (TJ = 25C) VO 5.75 6.0 6.25 5.75 6.0 6.25 Vdc Output Voltage (5.0 mA IO 1.0 A, PD 15 W) VO Vdc 8.0 Vdc Vin 21 Vdc - - - 5.7 6.0 6.3 9.0 Vdc Vin 21 Vdc 5.7 6.0 6.3 - - - 8.0 Vdc Vin 25 Vdc - 5.5 120 - 0.5 24 9.0 Vdc Vin 13 Vdc - 1.4 60 - 0.8 12 Regload - 1.3 120 - 1.3 30 mV IB - 3.3 8.0 - 3.3 8.0 mA 8.0 Vdc Vin 25 Vdc - - - - 0.3 1.3 5.0 mA IO 1.0 A - - 0.5 - 0.08 0.5 RR - 65 - 58 65 - dB VI - VO - 2.0 - - 2.0 - Vdc Vn - 10 - - 10 - mV/VO Output Resistance f = 1.0 kHz rO - 0.9 - - 0.9 - mW Short Circuit Current Limit (TA = 25C) ISC - 0.2 - - 0.2 - A Imax - 2.2 - - 2.2 - A TCVO - -0.3 - - -0.3 - mV/C Line Regulation, TJ = 25C (Note 6) Load Regulation, TJ = 25C (Note 6) Regline mV 5.0 mA IO 1.5 A Quiescent Current (TJ = 25C) Quiescent Current Change Ripple Rejection DIB mA 9.0 Vdc Vin 19 Vdc, f = 120 Hz Dropout Voltage (IO = 1.0 A, TJ = 25C) Output Noise Voltage (TA = 25C) 10 Hz f 100 kHz Vin = 35 Vdc Peak Output Current (TJ = 25C) Average Temperature Coefficient of Output Voltage 5. Tlow = 0C for MC78XXAC, CThigh = +125C for MC78XXAC, NCV7805 = -40 C for MC78XXB, MC78XXAB, NCV7805 6. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. http://onsemi.com 5 MC7800, MC7800A, NCV7805 ELECTRICAL CHARACTERISTICS (Vin = 11 V, IO = 1.0 A, TJ = Tlow to Thigh (Note 7), unless otherwise noted) MC7806AC Characteristic Symbol Min Typ Max Unit Output Voltage (TJ = 25C) VO 5.88 6.0 6.12 Vdc Output Voltage (5.0 mA IO 1.0 A, PD 15 W) VO 5.76 6.0 6.24 Vdc 8.6 Vdc Vin 21 Vdc Line Regulation (Note 8) Regline mV 8.6 Vdc Vin 25 Vdc, IO = 500 mA - 5.0 12 9.0 Vdc Vin 13 Vdc, IO = 1.0 A - 1.4 15 Load Regulation (Note 8) Regload mV 5.0 mA IO 1.5 A, TJ = 25C - 1.3 25 5.0 mA IO 1.0 A - 0.9 25 250 mA IO 750 mA - 0.2 15 - 3.3 6.0 Quiescent Current IB DIB Quiescent Current Change mA mA 9.0 Vdc Vin 25 Vdc, IO = 500 mA - - 0.8 9.0 Vdc Vin 21 Vdc, IO = 1.0 A, TJ = 25C - - 0.8 5.0 mA IO 1.0 A - - 0.5 RR 58 65 - dB VI - VO - 2.0 - Vdc Vn - 10 - mV/VO Output Resistance (f = 1.0 kHz) rO - 0.9 - mW Short Circuit Current Limit (TA = 25C) ISC - 0.2 - A Imax - 2.2 - A TCVO - -0.3 - mV/C Ripple Rejection 9.0 Vdc Vin 19 Vdc, f = 120 Hz, IO = 500 mA Dropout Voltage (IO = 1.0 A, TJ = 25C) Output Noise Voltage (TA = 25C) 10 Hz f 100 kHz Vin = 35 Vdc Peak Output Current (TJ = 25C) Average Temperature Coefficient of Output Voltage 7. Tlow = 0C for MC78XXAC, CThigh = +125C for MC78XXAC, C, NCV7805 = *40C for MC78XXB, MC78XXAB, NCV7805 8. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. http://onsemi.com 6 MC7800, MC7800A, NCV7805 ELECTRICAL CHARACTERISTICS (Vin = 14 V, IO = 500 mA, TJ = Tlow to Thigh (Note 9), unless otherwise noted) MC7808B Characteristic MC7808C Symbol Min Typ Max Min Typ Max Unit Output Voltage (TJ = 25C) VO 7.7 8.0 8.3 7.7 8.0 8.3 Vdc Output Voltage (5.0 mA IO 1.0 A, PD 15 W) VO Vdc 10.5 Vdc Vin 23 Vdc - - - 7.6 8.0 8.4 11.5 Vdc Vin 23 Vdc 7.6 8.0 8.4 - - - 10.5 Vdc Vin 25 Vdc - 6.0 160 - 6.0 32 11 Vdc Vin 17 Vdc - 1.7 80 - 1.7 16 Regload - 1.4 160 - 1.4 35 mV IB - 3.3 8.0 - 3.3 8.0 mA 10.5 Vdc Vin 25 Vdc - - - - - 1.0 5.0 mA IO 1.0 A - - 0.5 - - 0.5 RR - 62 - 56 62 - dB VI - VO - 2.0 - - 2.0 - Vdc Vn - 10 - - 10 - mV/VO Output Resistance f = 1.0 kHz rO - 0.9 - - 0.9 - mW Short Circuit Current Limit (TA = 25C) ISC - 0.2 - - 0.2 - A Imax - 2.2 - - 2.2 - A TCVO - -0.4 - - -0.4 - mV/C Line Regulation, TJ = 25C, (Note 10) Load Regulation, TJ = 25C (Note 10) Regline mV 5.0 mA IO 1.5 A Quiescent Current Quiescent Current Change Ripple Rejection DIB mA 11.5 Vdc Vin 18 Vdc, f = 120 Hz Dropout Voltage (IO = 1.0 A, TJ = 25C) Output Noise Voltage (TA = 25C) 10 Hz f 100 kHz Vin = 35 Vdc Peak Output Current (TJ = 25C) Average Temperature Coefficient of Output Voltage 9. Tlow = 0C for MC78XXAC, CThigh = +125C for MC78XXAC, C, NCV7805 = *40C for MC78XXB, MC78XXAB, NCV7805 10. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. http://onsemi.com 7 MC7800, MC7800A, NCV7805 ELECTRICAL CHARACTERISTICS (Vin = 14 V, IO = 1.0 A, TJ = Tlow to Thigh (Note 11), unless otherwise noted) MC7808AB/MC7808AC Characteristic Symbol Min Typ Max Unit Output Voltage (TJ = 25C) VO 7.84 8.0 8.16 Vdc Output Voltage (5.0 mA IO 1.0 A, PD 15 W) 10.6 Vdc Vin 23 Vdc VO 7.7 8.0 8.3 Vdc - 6.0 1.7 5.0 15 18 15 - 1.4 1.0 0.22 25 25 15 - 3.3 6.0 - - 0.8 0.8 0.5 Line Regulation (Note 12) 10.6 Vdc Vin 25 Vdc, IO = 500 mA 11 Vdc Vin 17 Vdc, IO = 1.0 A 10.4 Vdc Vin 23 Vdc, TJ = 25C Regline Load Regulation (Note 12) 5.0 mA IO 1.5 A, TJ = 25C 5.0 mA IO 1.0 A 250 mA IO 750 mA Regload Quiescent Current IB mV mV mA Quiescent Current Change 11 Vdc Vin 25 Vdc, IO = 500 mA 10.6 Vdc Vin 23 Vdc, IO = 1.0 A, TJ = 25C 5.0 mA IO 1.0 A DIB Ripple Rejection 11.5 Vdc Vin 21.5 Vdc, f = 120 Hz, IO = 500 mA RR 56 62 - dB VI - VO - 2.0 - Vdc Output Noise Voltage (TA = 25C) 10 Hz f 100 kHz Vn - 10 - mV/VO Output Resistance f = 1.0 kHz rO - 0.9 - mW Short Circuit Current Limit (TA = 25C) Vin = 35 Vdc ISC - 0.2 - A Peak Output Current (TJ = 25C) Imax - 2.2 - A TCVO - -0.4 - mV/C Dropout Voltage (IO = 1.0 A, TJ = 25C) Average Temperature Coefficient of Output Voltage mA 11. Tlow = 0C for MC78XXAC, CThigh = +125C for MC78XXAC, C, NCV7805 = *40C for MC78XXB, MC78XXAB, NCV7805 12. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. http://onsemi.com 8 MC7800, MC7800A, NCV7805 ELECTRICAL CHARACTERISTICS (Vin = 15 V, IO = 500 mA, TJ = Tlow to Thigh (Note 13), unless otherwise noted) MC7809B Characteristic MC7809C Symbol Min Typ Max Min Typ Max Unit Output Voltage (TJ = 25C) VO 8.65 9.0 9.35 8.65 9.0 9.35 Vdc Output Voltage (5.0 mA IO 1.0 A, PD 15 W) VO Vdc 11.5 Vdc Vin 24 Vdc Line Regulation, TJ = 25C (Note 14) 8.55 9.0 9.45 8.55 9.0 9.45 Regline mV 11 Vdc Vin 26 Vdc - 6.2 32 - 6.2 32 11.5 Vdc Vin 17 Vdc - 1.8 16 - 1.8 16 Regload - 1.5 35 - 1.5 35 mV IB - 3.4 8.0 - 3.4 8.0 mA Load Regulation, TJ = 25C (Note 14) 5.0 mA IO 1.5 A Quiescent Current Quiescent Current Change DIB mA 11.5 Vdc Vin 26 Vdc - - 1.0 - - 1.0 5.0 mA IO 1.0 A - - 0.5 - - 0.5 RR 56 61 - 56 61 - dB VI - VO - 2.0 - - 2.0 - Vdc Vn - 10 - - 10 - mV/VO Output Resistance f = 1.0 kHz rO - 1.0 - - 1.0 - mW Short Circuit Current Limit (TA = 25C) ISC - 0.2 - - 0.2 - A Imax - 2.2 - - 2.2 - A TCVO - -0.5 - - -0.5 - mV/C Ripple Rejection 11.5 Vdc Vin 21.5 Vdc, f = 120 Hz Dropout Voltage (IO = 1.0 A, TJ = 25C) Output Noise Voltage (TA = 25C) 10 Hz f 100 kHz Vin = 35 Vdc Peak Output Current (TJ = 25C) Average Temperature Coefficient of Output Voltage 13. Tlow = 0C for MC78XXAC, CThigh = +125C for MC78XXAC, C, NCV7805 = *40C for MC78XXB, MC78XXAB, NCV7805 14. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. http://onsemi.com 9 MC7800, MC7800A, NCV7805 ELECTRICAL CHARACTERISTICS (Vin = 15 V, IO = 1.0 A, TJ = 0C to 125C, unless otherwise noted) MC7809AC Symbol Min Typ Max Unit Output Voltage (TJ = 25C) VO 8.82 9.0 9.18 Vdc Output Voltage (5.0 mA IO 1.0 A, PD 15 W) 11.5 Vdc Vin 24 Vdc VO 8.65 9.0 9.35 Vdc - 6.2 1.8 5.2 16 7.0 16 - - 25 25 15 - 3.3 6.0 - - 0.8 0.8 0.5 56 61 - Characteristic Line Regulation (Note 15) 11.5 Vdc Vin 26 Vdc, IO = 500 mA 12 Vdc Vin 17 Vdc, IO = 1.0 A 11.5 Vdc Vin 24 Vdc, TJ = 25C Regline Load Regulation (Note 15) 5.0 mA IO 1.5 A, TJ = 25C 5.0 mA IO 1.0 A 250 mA IO 750 mA Regload Quiescent Current IB Quiescent Current Change 11.5 Vdc Vin 26 Vdc, IO = 500 mA 11.5 Vdc Vin 24 Vdc, IO = 1.0 A, TJ = 25C 5.0 mA IO 1.0 A DIB Ripple Rejection 11.5 Vdc Vin 21.5 Vdc, f = 120 Hz, IO = 500 mA RR Dropout Voltage (IO = 1.0 A, TJ = 25C) mV mV mA dB VI _ VO Output Noise Voltage (TA = 25C) 10 Hz f 100 kHz Vn Output Resistance f = 1.0 kHz mA 2.0 Vdc mV/VO - 10 - rO - 1.0 - Short Circuit Current Limit (TA = 25C) Vin = 35 Vdc ISC - 0.2 Peak Output Current (TJ = 25C) Imax - 2.2 - A TCVO - -0.5 - mV/C Average Temperature Coefficient of Output Voltage mW A 15. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. http://onsemi.com 10 MC7800, MC7800A, NCV7805 ELECTRICAL CHARACTERISTICS (Vin = 19 V, IO = 500 mA, TJ = Tlow to Thigh (Note 16), unless otherwise noted) MC7812B Characteristic MC7812C Symbol Min Typ Max Min Typ Max Unit Output Voltage (TJ = 25C) VO 11.5 12 12.5 11.5 12 12.5 Vdc Output Voltage (5.0 mA IO 1.0 A, PD 15 W) VO Vdc 14.5 Vdc Vin 27 Vdc - - - 11.4 12 12.6 15.5 Vdc Vin 27 Vdc 11.4 12 12.6 - - - 14.5 Vdc Vin 30 Vdc - 7.5 240 - 3.8 24 16 Vdc Vin 22 Vdc - 2.2 120 - 0.3 24 14.8 Vdc Vin 27 Vdc, IO = 1.0 A - - - - - 48 Regload - 1.6 240 - 8.1 60 mV IB - 3.4 8.0 - 3.4 6.5 mA Line Regulation, TJ = 25C (Note 17) Load Regulation, TJ = 25C (Note 17) Regline mV 5.0 mA IO 1.5 A Quiescent Current Quiescent Current Change DIB mA 14.5 Vdc Vin 30 Vdc, IO = 1.0 A, TJ = 25C - - - - - 0.7 15 Vdc Vin 30 Vdc - - 1.0 - - 0.8 5.0 mA IO 1.0 A - - 0.5 - - 0.5 RR - 60 - 55 60 - dB VI - VO - 2.0 - - 2.0 - Vdc Vn - 10 - - 10 - mV/VO Output Resistance f = 1.0 kHz rO - 1.1 - - 1.1 - mW Short Circuit Current Limit (TA = 25C) ISC - 0.2 - - 0.2 - A Imax - 2.2 - - 2.2 - A TCVO - -0.8 - - -0.8 - mV/C Ripple Rejection 15 Vdc Vin 25 Vdc, f = 120 Hz Dropout Voltage (IO = 1.0 A, TJ = 25C) Output Noise Voltage (TA = 25C) 10 Hz f 100 kHz Vin = 35 Vdc Peak Output Current (TJ = 25C) Average Temperature Coefficient of Output Voltage 16. Tlow = 0C for MC78XXAC, CThigh = +125C for MC78XXAC, C, NCV7805 = *40C for MC78XXB, MC78XXAB, NCV7805 17. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. http://onsemi.com 11 MC7800, MC7800A, NCV7805 ELECTRICAL CHARACTERISTICS (Vin = 19 V, IO = 1.0 A, TJ = Tlow to Thigh (Note 18), unless otherwise noted) MC7812AB/MC7812AC Characteristic Symbol Min Typ Max Unit Output Voltage (TJ = 25C) VO 11.75 12 12.25 Vdc Output Voltage (5.0 mA IO 1.0 A, PD 15 W) VO 11.5 12 12.5 Vdc 14.8 Vdc Vin 27 Vdc Line Regulation (Note 19) Regline mV 14.8 Vdc Vin 30 Vdc, IO = 500 mA - 3.8 18 16 Vdc Vin 22 Vdc, IO = 1.0 A - 2.2 20 14.5 Vdc Vin 27 Vdc, TJ = 25C - 6.0 120 Load Regulation (Note 19) Regload mV 5.0 mA IO 1.5 A, TJ = 25C - - 25 5.0 mA IO 1.0 A - - 25 - 3.4 6.0 Quiescent Current IB DIB Quiescent Current Change mA mA 15 Vdc Vin 30 Vdc, IO = 500 mA - - 0.8 14.8 Vdc Vin 27 Vdc, TJ = 25C - - 0.8 5.0 mA IO 1.0 A, TJ = 25C - - 0.5 RR 55 60 - dB VI - VO - 2.0 - Vdc Vn - 10 - mV/VO Output Resistance (f = 1.0 kHz) rO - 1.1 - mW Short Circuit Current Limit (TA = 25C) ISC - 0.2 - A Imax - 2.2 - A TCVO - -0.8 - mV/C Ripple Rejection 15 Vdc Vin 25 Vdc, f = 120 Hz, IO = 500 mA Dropout Voltage (IO = 1.0 A, TJ = 25C) Output Noise Voltage (TA = 25C) 10 Hz f 100 kHz Vin = 35 Vdc Peak Output Current (TJ = 25C) Average Temperature Coefficient of Output Voltage 18. Tlow = 0C for MC78XXAC, CThigh = +125C for MC78XXAC, C, NCV7805 = *40C for MC78XXB, MC78XXAB, NCV7805 19. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. http://onsemi.com 12 MC7800, MC7800A, NCV7805 ELECTRICAL CHARACTERISTICS (Vin = 23 V, IO = 500 mA, TJ = Tlow to Thigh (Note 20), unless otherwise noted) MC7815B Characteristic MC7815C Symbol Min Typ Max Min Typ Max Unit Output Voltage (TJ = 25C) VO 14.4 15 15.6 14.4 15 15.6 Vdc Output Voltage (5.0 mA IO 1.0 A, PD 15 W) VO Vdc 17.5 Vdc Vin 30 Vdc - - - 14.25 15 15.75 18.5 Vdc Vin 30 Vdc 14.25 15 15.75 - - - 17.9 Vdc Vin 30 Vdc - 8.5 300 - 8.5 30 20 Vdc Vin 26 Vdc - 3.0 150 - 3.0 28 Regload - 1.8 300 - 1.8 55 mV IB - 3.5 8.0 - 3.5 6.5 mA 17.5 Vdc Vin 30 Vdc - - - - - 0.8 17.5 Vdc Vin 30 Vdc, IO = 1.0 A, TJ = 25C - - 1.0 - - 0.7 5.0 mA IO 1.0 A - - 0.5 - - 0.5 RR - 58 - 54 58 - VI - VO - 2.0 - - 2.0 - Vdc Vn - 10 - - 10 - mV/VO Output Resistance f = 1.0 kHz rO - 1.2 - - 1.2 - mW Short Circuit Current Limit (TA = 25C) ISC - 0.2 - - 0.2 - A Imax - 2.2 - - 2.2 - A TCVO - -1.0 - - -1.0 - mV/C Line Regulation, TJ = 25C (Note 21) Load Regulation, TJ = 25C (Note 21) Regline mV 5.0 mA IO 1.5 A Quiescent Current Quiescent Current Change Ripple Rejection DIB mA dB 18.5 Vdc Vin 28.5 Vdc, f = 120 Hz Dropout Voltage (IO = 1.0 A, TJ = 25C) Output Noise Voltage (TA = 25C) 10 Hz f 100 kHz Vin = 35 Vdc Peak Output Current (TJ = 25C) Average Temperature Coefficient of Output Voltage 20. Tlow = 0C for MC78XXAC, CThigh = +125C for MC78XXAC, C, NCV7805 = *40C for MC78XXB, MC78XXAB, NCV7805 21. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. http://onsemi.com 13 MC7800, MC7800A, NCV7805 ELECTRICAL CHARACTERISTICS (Vin = 23 V, IO = 1.0 A, TJ = Tlow to Thigh (Note 22), unless otherwise noted) MC7815AB/MC7815AC Characteristic Symbol Min Typ Max Unit Output Voltage (TJ = 25C) VO 14.7 15 15.3 Vdc Output Voltage (5.0 mA IO 1.0 A, PD 15 W) VO 14.4 15 15.6 Vdc 17.9 Vdc Vin 30 Vdc Line Regulation (Note 23) Regline mV 17.9 Vdc Vin 30 Vdc, IO = 500 mA - 8.5 20 20 Vdc Vin 26 Vdc - 3.0 22 17.5 Vdc Vin 30 Vdc, IO = 1.0 A, TJ = 25C - 7.0 20 Load Regulation (Note 23) Regload mV 5.0 mA IO 1.5 A, TJ = 25C - 1.8 25 5.0 mA IO 1.0 A - 1.5 25 - 1.2 15 - 3.5 6.0 250 mA IO 750 mA Quiescent Current IB DIB Quiescent Current Change mA mA 17.5 Vdc Vin 30 Vdc, IO = 500 mA - - 0.8 17.5 Vdc Vin 30 Vdc, IO = 1.0 A, TJ = 25C - - 0.8 5.0 mA IO 1.0 A - - 0.5 RR 60 80 - dB VI - VO - 2.0 - Vdc Vn - 10 - mV/VO Output Resistance f = 1.0 kHz rO - 1.2 - mW Short Circuit Current Limit (TA = 25C) ISC - 0.2 - A Imax - 2.2 - A TCVO - -1.0 - mV/C Ripple Rejection 18.5 Vdc Vin 28.5 Vdc, f = 120 Hz, IO = 500 mA Dropout Voltage (IO = 1.0 A, TJ = 25C) Output Noise Voltage (TA = 25C) 10 Hz f 100 kHz Vin = 35 Vdc Peak Output Current (TJ = 25C) Average Temperature Coefficient of Output Voltage 22. Tlow = 0C for MC78XXAC, CThigh = +125C for MC78XXAC, C, NCV7805 = *40C for MC78XXB, MC78XXAB, NCV7805 23. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. http://onsemi.com 14 MC7800, MC7800A, NCV7805 ELECTRICAL CHARACTERISTICS (Vin = 27 V, IO = 500 mA, TJ = Tlow to Thigh (Note 24), unless otherwise noted) MC7818B Characteristic MC7818C Symbol Min Typ Max Min Typ Max Unit Output Voltage (TJ = 25C) VO 17.3 18 18.7 17.3 18 18.7 Vdc Output Voltage (5.0 mA IO 1.0 A, PD 15 W) VO Vdc 21 Vdc Vin 33 Vdc - - - 17.1 18 18.9 22 Vdc Vin 33 Vdc 17.1 18 18.9 - - - 21 Vdc Vin 33 Vdc - 9.5 360 - 9.5 50 24 Vdc Vin 30 Vdc - 3.2 180 - 3.2 25 Regload - 2.0 360 - 2.0 55 mV IB - 3.5 8.0 - 3.5 6.5 mA 21 Vdc Vin 33 Vdc - - - - - 1.0 5.0 mA IO 1.0 A - - 0.5 - - 0.5 RR - 57 - 53 57 - dB ViI - VO - 2.0 - - 2.0 - Vdc Vn - 10 - - 10 - mV/VO Output Resistance f = 1.0 kHz rO - 1.3 - - 1.3 - mW Short Circuit Current Limit (TA = 25C) ISC - 0.2 - - 0.2 - A Imax - 2.2 - - 2.2 - A TCVO - -1.5 - - -1.5 - mV/C Line Regulation, (Note 25) Load Regulation, (Note 25) Regline mV 5.0 mA IO 1.5 A Quiescent Current Quiescent Current Change Ripple Rejection DIB mA 22 Vdc Vin 33 Vdc, f = 120 Hz Dropout Voltage (IO = 1.0 A, TJ = 25C) Output Noise Voltage (TA = 25C) 10 Hz f 100 kHz Vin = 35 Vdc Peak Output Current (TJ = 25C) Average Temperature Coefficient of Output Voltage 24. Tlow = 0C for MC78XXAC, CThigh = +125C for MC78XXAC, C, NCV7805 = *40C for MC78XXB, MC78XXAB, NCV7805 25. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. http://onsemi.com 15 MC7800, MC7800A, NCV7805 ELECTRICAL CHARACTERISTICS (Vin = 27 V, IO = 1.0 A, TJ = Tlow to Thigh (Note 26), unless otherwise noted) MC7818AC Characteristic Symbol Min Typ Max Unit Output Voltage (TJ = 25C) VO 17.64 18 18.36 Vdc Output Voltage (5.0 mA IO 1.0 A, PD 15 W) VO 17.3 18 18.7 Vdc 21 Vdc Vin 33 Vdc Line Regulation (Note 27) Regline mV 21 Vdc Vin 33 Vdc, IO = 500 mA - 9.5 22 24 Vdc Vin 30 Vdc, IO = 1.0 A - 3.2 25 24 Vdc Vin 30 Vdc, IO = 1.0 A, TJ = 25C - 3.2 10.5 20.6 Vdc Vin 33 Vdc, IO = 1.0 A, TJ = 25C - 8.0 22 Load Regulation (Note 27) Regload mV 5.0 mA IO 1.5 A, TJ = 25C - 2.0 25 5.0 mA IO 1.0 A - 1.8 25 250 mA IO 750 mA - 1.5 15 - 3.5 6.0 Quiescent Current IB DIB Quiescent Current Change mA 21 Vdc Vin 33 Vdc, IO = 500 mA - - 0.8 21.5 Vdc Vin 30 Vdc, TJ = 25C - - 0.8 5.0 mA IO 1.0 A mA - - 0.5 RR 53 57 - dB VI - VO - 2.0 - Vdc Vn - 10 - mV/VO Output Resistance f = 1.0 kHz rO - 1.3 - mW Short Circuit Current Limit (TA = 25C) ISC - 0.2 - A Imax - 2.2 - A TCVO - -1.5 - mV/C Ripple Rejection 22 Vdc Vin 32 Vdc, f = 120 Hz, IO = 500 mA Dropout Voltage (IO = 1.0 A, TJ = 25C) Output Noise Voltage (TA = 25C) 10 Hz f 100 kHz Vin = 35 Vdc Peak Output Current (TJ = 25C) Average Temperature Coefficient of Output Voltage 26. Tlow = 0C for MC78XXAC, CThigh = +125C for MC78XXAC, C, NCV7805 = *40C for MC78XXB, MC78XXAB, NCV7805 27. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. http://onsemi.com 16 MC7800, MC7800A, NCV7805 ELECTRICAL CHARACTERISTICS (Vin = 33 V, IO = 500 mA, TJ = Tlow to Thigh (Note 28), unless otherwise noted) MC7824B Characteristic MC7824C Symbol Min Typ Max Min Typ Max Unit Output Voltage (TJ = 25C) VO 23 24 25 23 24 25 Vdc Output Voltage (5.0 mA IO 1.0 A, PD 15 W) VO Vdc 27 Vdc Vin 38 Vdc - - - 22.8 24 25.2 28 Vdc Vin 38 Vdc 22.8 24 25.2 - - - 27 Vdc Vin 38 Vdc - 11.5 480 - 2.7 60 30 Vdc Vin 36 Vdc - 3.8 240 - 2.7 48 Regload - 2.1 480 - 4.4 65 mV IB - 3.6 8.0 - 3.6 6.5 mA 27 Vdc Vin 38 Vdc - - - - - 1.0 5.0 mA IO 1.0 A - - 0.5 - - 0.5 RR - 54 - 50 54 - dB VI - VO - 2.0 - - 2.0 - Vdc Vn - 10 - - 10 - mV/VO Output Resistance f = 1.0 kHz rO - 1.4 - - 1.4 - mW Short Circuit Current Limit (TA = 25C) ISC - 0.2 - - 0.2 - A Imax - 2.2 - - 2.2 - A TCVO - -2.0 - - -2.0 - mV/C Line Regulation, (Note 29) Load Regulation, (Note 29) Regline mV 5.0 mA IO 1.5 A Quiescent Current Quiescent Current Change Ripple Rejection DIB mA 28 Vdc Vin 38 Vdc, f = 120 Hz Dropout Voltage (IO = 1.0 A, TJ = 25C) Output Noise Voltage (TA = 25C) 10 Hz f 100 kHz Vin = 35 Vdc Peak Output Current (TJ = 25C) Average Temperature Coefficient of Output Voltage 28. Tlow = 0C for MC78XXAC, CThigh = +125C for MC78XXAC, C, NCV7805 = *40C for MC78XXB, MC78XXAB, NCV7805 29. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. http://onsemi.com 17 MC7800, MC7800A, NCV7805 ELECTRICAL CHARACTERISTICS (Vin = 33 V, IO = 1.0 A, TJ = Tlow to Thigh (Note 30), unless otherwise noted) MC7824AC Characteristic Symbol Min Typ Max Unit Output Voltage (TJ = 25C) VO 23.5 24 24.5 Vdc Output Voltage (5.0 mA IO 1.0 A, PD 15 W) VO 23.2 24 25.8 Vdc 27.3 Vdc Vin 38 Vdc Line Regulation (Note 31) Regline mV 27 Vdc Vin 38 Vdc, IO = 500 mA - 11.5 25 30 Vdc Vin 36 Vdc, IO = 1.0 A - 3.8 28 30 Vdc Vin 36 Vdc, TJ = 25C - 3.8 12 26.7 Vdc Vin 38 Vdc, IO = 1.0 A, TJ = 25C - 10 25 Load Regulation (Note 31) Regload mV 5.0 mA IO 1.5 A, TJ = 25C - 2.1 15 5.0 mA IO 1.0 A - 2.0 25 250 mA IO 750 mA - 1.8 15 - 3.6 6.0 Quiescent Current IB DIB Quiescent Current Change mA 27.3 Vdc Vin 38 Vdc, IO = 500 mA - - 0.8 27 Vdc Vin 38 Vdc, TJ = 25C - - 0.8 5.0 mA IO 1.0 A mA - - 0.5 RR 45 54 - dB VI - VO - 2.0 - Vdc Vn - 10 - mV/VO Output Resistance (f = 1.0 kHz) rO - 1.4 - mW Short Circuit Current Limit (TA = 25C) ISC - 0.2 - A Imax - 2.2 - A TCVO - -2.0 - mV/C Ripple Rejection 28 Vdc Vin 38 Vdc, f = 120 Hz, IO = 500 mA Dropout Voltage (IO = 1.0 A, TJ = 25C) Output Noise Voltage (TA = 25C) 10 Hz f 100 kHz Vin = 35 Vdc Peak Output Current (TJ = 25C) Average Temperature Coefficient of Output Voltage 30. Tlow = 0C for MC78XXAC, CThigh = +125C for MC78XXAC, C, NCV7805 = *40C for MC78XXB, MC78XXAB, NCV7805 31. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. http://onsemi.com 18 MC7800, MC7800A, NCV7805 3.0 80 2.5 RR, RIPPLE REJECTION (dB) I O, OUTPUT CURRENT (A) TJ = -40C TJ = 0C 2.0 TJ = 25C 1.5 TJ = 85C 1.0 TJ = 125C 0.5 0 4.0 6.0 8.0 10 12 15 20 25 30 35 70 60 50 40 4.0 40 f = 120 Hz IO = 20 mA DVin = 1.0 V(RMS) PART # Vin MC7805C= 10 V MC7806C= 11 V MC7808C= 14 V MC7812C= 19 V MC7815C= 23 V MC7818C= 27 V MC7824C= 33 V 6.0 8.0 10 Vin-V out, INPUT/OUTPUT VOLTAGE DIFFERENTIAL (V) 12 14 16 18 20 22 24 VO, OUTPUT VOLTAGE (V) Figure 2. Peak Output Current as a Function of Input/Output Differential Voltage (MC78XXC, AC, B) Figure 3. Ripple Rejection as a Function of Output Voltages (MC78XXC, AC, B) VO, OUTPUT VOLTAGE (V) RR, RIPPLE REJECTION (dB) 80 70 MC78XXB, C, AC 60 Vin = 8.0 V to 18 V IO = 500 mA f = 120 Hz TA = 25C 50 40 30 0.01 0.1 1.0 20 60 100 140 TJ, JUNCTION TEMPERATURE (C) Figure 4. Ripple Rejection as a Function of Frequency (MC78XXC, AC, B) Figure 5. Output Voltage as a Function of Junction Temperature (MC7805C, AC, B) 180 6.0 IB , QUIESCENT CURRENT (mA) Z O , OUTPUT IMPEDANCE (m) -20 f, FREQUENCY (kHz) 5.0 f = 120 Hz IO = 500 mA CL = 0 mF 1.0 0.5 0.3 0.2 0.1 4.0 4.9 4.8 -60 10 10 3.0 2.0 Vin = 20 V IO = 5.0 mA 5.0 8.0 12 16 20 4.0 3.0 2.0 1.0 0 -75 24 Vin = 10 V VO = 5.0 V IL = 20 mA -50 -25 0 25 50 75 100 TJ, JUNCTION TEMPERATURE (C) VO, OUTPUT VOLTAGE (V) Figure 6. Output Impedance as a Function of Output Voltage (MC78XXC, AC, B) Figure 7. Quiescent Current as a Function of Temperature (MC78XXC, AC, B) http://onsemi.com 19 125 MC7800, MC7800A, NCV7805 APPLICATIONS INFORMATION Design Considerations wire lengths, or if the output load capacitance is large. An input bypass capacitor should be selected to provide good high-frequency characteristics to insure stable operation under all load conditions. A 0.33 mF or larger tantalum, mylar, or other capacitor having low internal impedance at high frequencies should be chosen. The bypass capacitor should be mounted with the shortest possible leads directly across the regulators input terminals. Normally good construction techniques should be used to minimize ground loops and lead resistance drops since the regulator has no external sense lead. The MC7800 Series of fixed voltage regulators are designed with Thermal Overload Protection that shuts down the circuit when subjected to an excessive power overload condition, Internal Short Circuit Protection that limits the maximum current the circuit will pass, and Output Transistor Safe- Area Compensation that reduces the output short circuit current as the voltage across the pass transistor is increased. In many low current applications, compensation capacitors are not required. However, it is recommended that the regulator input be bypassed with a capacitor if the regulator is connected to the power supply filter with long MC7805 Input Output 0.33 mF R IO MC7805 Constant Current to Grounded Load Input 7 0.33 mF 2 0.1 mF 6 3 The MC7800 regulators can also be used as a current source when connected as above. In order to minimize dissipation the MC7805C is chosen in this application. Resistor R determines the current as follows: 1.0 k I + 5.0V ) I B O R 4 10 k MC1741G VO = 7.0 V to 20 V VIN = VO 2.0 V IB ^ 3.2 mA over line and load changes. For example, a 1.0 A current source would require R to be a 5.0 W, 10 W resistor and the output voltage compliance would be the input voltage less 7.0 V. The addition of an operational amplifier allows adjustment to higher or intermediate values while retaining regulation characteristics. The minimum voltage obtainable with this arrangement is 2.0 V greater than the regulator voltage. Figure 8. Current Regulator Figure 9. Adjustable Output Regulator RSource MJ2955 or Equiv. Input Input 0.33 mF R RSC RSource MC78XX 0.33 mF 2N6049 or Equiv. Output R 10 mF 1.0 mF MJ2955 or Equiv. 1.0 mF 10 mF MC78XX 1.0 mF Output XX = 2 digits of type number indicating voltage. XX = 2 digits of type number indicating voltage. The MC7800 series can be current boosted with a PNP transistor. The MJ2955 provides current to 5.0 A. Resistor R in conjunction with the VBE of the PNP determines when the pass transistor begins conducting; this circuit is not short circuit proof. Input/output differential voltage minimum is increased by VBE of the pass transistor. The circuit of Figure 10 can be modified to provide supply protection against short circuits by adding a short circuit sense resistor, RSC, and an additional PNP transistor. The current sensing PNP must be able to handle the short circuit current of the three-terminal regulator. Therefore, a four-ampere plastic power transistor is specified. Figure 10. Current Boost Regulator Figure 11. Short Circuit Protection http://onsemi.com 20 MC7800, MC7800A, NCV7805 2.5 20 Vin - Vout , INPUT-OUTPUT VOLTAGE DIFFERENTIAL (V) qHS = 0C/W 16 qHS = 5C/W 12 qHS = 15C/W 8.0 4.0 No Heatsink 0 -50 -25 0 25 50 75 100 125 IO = 1.0 A IO = 500 mA 2.0 IO = 200 mA 1.5 IO = 20 mA IO = 0 mA 1.0 0.5 DVO = 2% of VO - - - Extended Curve for MC78XXB 0 -75 150 -50 -25 0 25 50 75 100 125 TJ, JUNCTION TEMPERATURE (C) Figure 12. Worst Case Power Dissipation versus Ambient Temperature (Case 221A) Figure 13. Input Output Differential as a Function of Junction Temperature (MC78XXC, AC, B) JUNCTIONTOAIR (C/W) R JA, THERMAL RESISTANCE 80 3.5 70 PD(max) for TA = 50C Free Air Mounted Vertically 60 IIII IIII IIII IIII 2.0 oz. Copper L Minimum Size Pad 50 2.5 2.0 L 1.5 40 RqJA 30 3.0 0 5.0 10 15 20 25 PD, MAXIMUM POWER DISSIPATION (W) TA, AMBIENT TEMPERATURE (C) 1.0 30 L, LENGTH OF COPPER (mm) 100 JUNCTION-T O-AIR ( C/W) 2.4 PD(max) for TA = 50C Free Air Mounted Vertically 90 2.0 IIII IIII IIII IIII 80 Minimum Size Pad 70 60 2.0 oz. Copper L 1.6 L 1.2 0.8 50 0.4 RqJA 40 0 0 5.0 10 15 20 25 30 L, LENGTH OF COPPER (mm) Figure 15. DPAK Thermal Resistance and Maximum Power Dissipation versus P.C.B. Copper Length http://onsemi.com 21 PD, MAXIMUM POWER DISSIPATION (W) Figure 14. D2PAK Thermal Resistance and Maximum Power Dissipation versus P.C.B. Copper Length R JA, THERMAL RESISTANCE PD , POWER DISSIPATION (W) qJC = 5C/W qJA = 65C/W TJ(max) = 150C MC7800, MC7800A, NCV7805 DEFINITIONS Quiescent Current - That part of the input current that is not delivered to the load. Output Noise Voltage - The rms ac voltage at the output, with constant load and no input ripple, measured over a specified frequency range. Long Term Stability - Output voltage stability under accelerated life test conditions with the maximum rated voltage listed in the devices' electrical characteristics and maximum power dissipation. Line Regulation - The change in output voltage for a change in the input voltage. The measurement is made under conditions of low dissipation or by using pulse techniques such that the average chip temperature is not significantly affected. Load Regulation - The change in output voltage for a change in load current at constant chip temperature. Maximum Power Dissipation - The maximum total device dissipation for which the regulator will operate within specifications. ORDERING INFORMATION Operating Temperature Range Package Shipping D2PAK 50 Units /Rail MC7805ABD2TG D2PAK (Pb-free) 50 Units /Rail MC7805ABD2TR4 D2PAK 800 / Tape & Reel D2PAK 800 / Tape & Reel Device Nominal Voltage MC7805ABD2T T = -40C to +125C MC7805ABD2TR4G (Pb-free) MC7805ABT TO 220 50 Units /Rail MC7805ABTG TO 220 (Pb-free) 50 Units /Rail MC7805ACD2T D2PAK 50 Units /Rail MC7805ACD2TG D2PAK 50 Units /Rail (Pb-free) MC7805ACD2TR4 T = 0C to +125C MC7805ACD2TR4G D2PAK 800 / Tape & Reel D2PAK 800 / Tape & Reel (Pb-free) MC7805ACT 5.0 V TO 220 50 Units /Rail MC7805ACTG TO 220 (Pb-free) 50 Units /Rail MC7805BD2T D2PAK 50 Units /Rail MC7805BD2TG D2PAK 50 Units /Rail (Pb-free) MC7805BD2TR4 D2PAK 800 / Tape & Reel MC7805BD2TR4G D2PAK 800 / Tape & Reel (Pb-free) MC7805BDT T = -40C to +125C MC7805BDTG MC7805BDTRK MC7805BDTRKG DPAK 75 Units / Rail DPAK (Pb-free) 75 Units / Rail DPAK 2500 / Tape & Reel DPAK (Pb-free) 2500 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NCV devices: Tlow = -40C, Thigh = +125C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control. http://onsemi.com 22 MC7800, MC7800A, NCV7805 ORDERING INFORMATION Operating Temperature Range Package Shipping TO 220 50 Units /Rail TO 220 (Pb-free) 50 Units /Rail NCV7805BD2T* D2PAK 50 Units /Rail NCV7805BD2TG* D2PAK 50 Units /Rail Device Nominal Voltage MC7805BT MC7805BTG (Pb-free) T = -40C to +125C NCV7805BD2TR4* NCV7805BD2TR4G* D2PAK 800 / Tape & Reel D2PAK 800 / Tape & Reel (Pb-free) NCV7805BT* TO 220 50 Units /Rail NCV7805BTG* TO 220 (Pb-free) 50 Units /Rail MC7805CD2T D2PAK 50 Units /Rail D2PAK (Pb-free) 50 Units /Rail D2PAK 800 / Tape & Reel D2PAK (Pb-free) 800 / Tape & Reel MC7805CD2TG 5.0 V MC7805CD2TR4 MC7805CD2TR4G MC7805CDT T = 0C to +125C MC7805CDTG MC7805CDTRK DPAK 75 Units / Rail DPAK (Pb-free) 75 Units / Rail DPAK 2500 / Tape & Reel DPAK (Pb-free) 2500 / Tape & Reel TO 220 50 Units /Rail TO 220 (Pb-free) 50 Units /Rail TO 220 50 Units /Rail TO 220 (Pb-free) 50 Units /Rail MC7806BD2T D2PAK 50 Units /Rail MC7806BD2TG D2PAK 50 Units /Rail MC7805CDTRKG MC7805CT MC7805CTG MC7806ACT MC7806ACTG 6.0 V T = 0C to +125C (Pb-free) MC7806BD2TR4 MC7806BD2TR4G T = -40C to +125C D2PAK 800 / Tape & Reel D2PAK 800 / Tape & Reel (Pb-free) MC7806BT MC7806BTG MC7806CT MC7806CTG T = 0C to +125C TO 220 50 Units /Rail TO 220 (Pb-free) 50 Units /Rail TO 220 50 Units /Rail TO 220 (Pb-free) 50 Units /Rail For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NCV devices: Tlow = -40C, Thigh = +125C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control. http://onsemi.com 23 MC7800, MC7800A, NCV7805 ORDERING INFORMATION Operating Temperature Range Package Shipping MC7808ABD2T D2PAK 50 Units /Rail MC7808ABD2TG D2PAK 50 Units /Rail Device Nominal Voltage (Pb-free) MC7808ABD2TR4 T = -40C to +125C MC7808ABD2TR4G D2PAK 800 / Tape & Reel D2PAK 800 / Tape & Reel (Pb-free) MC7808ABT TO 220 50 Units /Rail TO 220 (Pb-free) 50 Units /Rail TO 220 50 Units /Rail TO 220 (Pb-free) 50 Units /Rail D2PAK 50 Units /Rail MC7808BD2TG D2PAK (Pb-free) 50 Units /Rail MC7808BD2TR4 D2PAK 800 / Tape & Reel D2PAK (Pb-free) 800 / Tape & Reel MC7808ABTG MC7808ACT T = 0C to +125C MC7808ACTG MC7808BD2T MC7808BD2TR4G MC7808BDT T = -40C to +125C MC7808BDTG MC7808BDTRK 8.0 V DPAK 75 Units / Rail DPAK (Pb-free) 75 Units / Rail DPAK 2500 / Tape & Reel DPAK (Pb-free) 2500 / Tape & Reel TO 220 50 Units /Rail MC7808BTG TO 220 (Pb-free) 50 Units /Rail MC7808CD2T D2PAK 50 Units /Rail MC7808CD2TG D2PAK 50 Units /Rail MC7808BDTRKG MC7808BT (Pb-free) MC7808CD2TR4 D2PAK 800 / Tape & Reel MC7808CD2TR4G D2PAK 800 / Tape & Reel (Pb-free) MC7808CDT MC7808CDTG T = 0C to +125C MC7808CDTRK MC7808CDTRKG MC7808CT MC7808CTG DPAK 75 Units / Rail DPAK (Pb-free) 75 Units / Rail DPAK 2500 / Tape & Reel DPAK (Pb-free) 2500 / Tape & Reel TO 220 50 Units /Rail TO 220 (Pb-free) 50 Units /Rail For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NCV devices: Tlow = -40C, Thigh = +125C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control. http://onsemi.com 24 MC7800, MC7800A, NCV7805 ORDERING INFORMATION Device Nominal Voltage Operating Temperature Range MC7809ACT T = 0C to +125C MC7809ACTG MC7809BT T = -40C to +125C MC7809BTG MC7809CD2T MC7809CD2TG 9.0 V Package Shipping TO 220 50 Units /Rail TO 220 (Pb-free) 50 Units /Rail TO 220 50 Units /Rail TO 220 (Pb-free) 50 Units /Rail D2PAK 50 Units /Rail D2PAK 50 Units /Rail (Pb-free) D2PAK 800 / Tape & Reel D2PAK (Pb-free) 800 / Tape & Reel TO 220 50 Units /Rail TO 220 (Pb-free) 50 Units /Rail D2PAK 50 Units /Rail MC7812ABD2TG D2PAK (Pb-free) 50 Units /Rail MC7812ABD2TR4 D2PAK 800 / Tape & Reel D2PAK (Pb-free) 800 / Tape & Reel MC7809CD2TR4 T = 0C to +125C MC7809CD2TR4G MC7809CT MC7809CTG MC7812ABD2T T = -40C to +125C MC7812ABD2TR4G MC7812ABT TO 220 50 Units /Rail MC7812ABTG TO 220 (Pb-free) 50 Units /Rail MC7812ACD2T D2PAK 50 Units /Rail MC7812ACD2TG D2PAK 50 Units /Rail (Pb-free) MC7812ACD2TR4 MC7812ACD2TR4G 12 V T = 0C to +125C D2PAK 800 / Tape & Reel D2PAK 800 / Tape & Reel (Pb-free) MC7812ACT TO 220 50 Units /Rail MC7812ACTG TO 220 (Pb-free) 50 Units /Rail MC7812BD2T D2PAK 50 Units /Rail MC7812BD2TG D2PAK 50 Units /Rail (Pb-free) MC7812BD2TR4 MC7812BD2TR4G T = -40C to +125C D2PAK 800 / Tape & Reel D2PAK 800 / Tape & Reel (Pb-free) MC7812BDT MC7812BDTG DPAK 75 Units / Rail DPAK (Pb-free) 75 Units / Rail For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NCV devices: Tlow = -40C, Thigh = +125C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control. http://onsemi.com 25 MC7800, MC7800A, NCV7805 ORDERING INFORMATION Operating Temperature Range Package Shipping DPAK 2500 / Tape & Reel DPAK (Pb-free) 2500 / Tape & Reel TO 220 50 Units /Rail TO 220 (Pb-free) 50 Units /Rail D2PAK 50 Units /Rail NCV7812BD2TR4 * D2PAK 800 / Tape & Reel NCV7812BD2TR4G * D2PAK 800 / Tape & Reel Device Nominal Voltage MC7812BDTRK MC7812BDTRKG MC7812BT MC7812BTG NCV7812BD2T * 12 V T = -40C to +125C (Pb-free) NCV7812BT * TO 220 50 Units /Rail TO 220 (Pb-free) 50 Units /Rail MC7812CD2T D2PAK 50 Units /Rail MC7812CD2TG D2PAK 50 Units /Rail NCV7812BTG * (Pb-free) MC7812CD2TR4 MC7812CD2TR4G MC7812CDT MC7812CDTG 12 V T = 0C to +125C MC7812CDTRK MC7812CDTRKG MC7812CT MC7812CTG D2PAK 800 / Tape & Reel D2PAK (Pb-free) 800 / Tape & Reel DPAK 75 Units / Rail DPAK (Pb-free) 75 Units / Rail DPAK 2500 / Tape & Reel DPAK (Pb-free) 2500 / Tape & Reel TO 220 50 Units /Rail TO 220 (Pb-free) 50 Units /Rail For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NCV devices: Tlow = -40C, Thigh = +125C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control. http://onsemi.com 26 MC7800, MC7800A, NCV7805 ORDERING INFORMATION Operating Temperature Range Package Shipping MC7815ABD2T D2PAK 50 Units /Rail MC7815ABD2TG D2PAK 50 Units /Rail Device Nominal Voltage (Pb-free) MC7815ABD2TR4 T = -40C to +125C MC7815ABD2TR4G D2PAK 800 / Tape & Reel D2PAK 800 / Tape & Reel (Pb-free) MC7815ABT TO 220 50 Units /Rail TO 220 (Pb-free) 50 Units /Rail D2PAK 50 Units /Rail D2PAK (Pb-free) 50 Units /Rail TO 220 50 Units /Rail MC7815ACTG TO 220 (Pb-free) 50 Units /Rail MC7815BD2T D2PAK 50 Units /Rail D2PAK (Pb-free) 50 Units /Rail MC7815ABTG MC7815ACD2T 15 V MC7815ACD2TG MC7815ACT MC7815BD2TG T = 0C to +125C T = -40C to +125C For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NCV devices: Tlow = -40C, Thigh = +125C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control. http://onsemi.com 27 MC7800, MC7800A, NCV7805 ORDERING INFORMATION Operating Temperature Range Package Shipping MC7815BD2TR4 D2PAK 800 / Tape & Reel MC7815BD2TR4G D2PAK 800 / Tape & Reel Device Nominal Voltage (Pb-free) MC7815BDT DPAK 75 Units / Rail DPAK (Pb-free) 75 Units / Rail DPAK 2500 / Tape & Reel DPAK (Pb-free) 2500 / Tape & Reel TO 220 50 Units /Rail MC7815BTG TO 220 (Pb-free) 50 Units /Rail MC7815CD2T D2PAK 50 Units /Rail D2PAK (Pb-free) 50 Units /Rail D2PAK 800 / Tape & Reel D2PAK (Pb-free) 800 / Tape & Reel MC7815BDTG T = -40C to +125C MC7815BDTRK MC7815BDTRKG MC7815BT MC7815CD2TG 15 V MC7815CD2TR4 MC7815CD2TR4G MC7815CDT T = 0C to +125C MC7815CDTG MC7815CDTRK DPAK 75 Units / Rail DPAK (Pb-free) 75 Units / Rail DPAK 2500 / Tape & Reel DPAK (Pb-free) 2500 / Tape & Reel TO 220 50 Units /Rail TO 220 (Pb-free) 50 Units /Rail TO 220 50 Units /Rail TO 220 (Pb-free) 50 Units /Rail TO 220 50 Units /Rail TO 220 (Pb-free) 50 Units /Rail D2PAK 50 Units /Rail MC7818CD2TR4 D2PAK 800 / Tape & Reel MC7818CD2TR4G D2PAK 800 / Tape & Reel MC7815CDTRKG MC7815CT MC7815CTG MC7818ACT T = 0C to +125C MC7818ACTG MC7818BT T = -40C to +125C MC7818BTG MC7818CD2T 18 V T = 0C to +125C MC7818CT MC7818CTG (Pb-free) TO 220 50 Units /Rail TO 220 (Pb-free) 50 Units /Rail For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NCV devices: Tlow = -40C, Thigh = +125C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control. http://onsemi.com 28 MC7800, MC7800A, NCV7805 ORDERING INFORMATION Operating Temperature Range Package Shipping TO 220 50 Units /Rail TO 220 (Pb-free) 50 Units /Rail MC7824BD2T D2PAK 50 Units /Rail MC7824BD2TG D2PAK 50 Units /Rail Device Nominal Voltage MC7824ACT T = 0C to +125C MC7824ACTG (Pb-free) MC7824BD2TR4 T = -40C to +125C MC7824BD2TR4G D2PAK 800 / Tape & Reel D2PAK 800 / Tape & Reel (Pb-free) MC7824BT TO 220 50 Units /Rail TO 220 (Pb-free) 50 Units /Rail D2PAK 50 Units /Rail MC7824CD2TG D2PAK (Pb-free) 50 Units /Rail MC7824CD2TR4 D2PAK 800 / Tape & Reel D2PAK (Pb-free) 800 / Tape & Reel TO 220 50 Units /Rail TO 220 (Pb-free) 50 Units /Rail 24 V MC7824BTG MC7824CD2T T = 0C to +125C MC7824CD2TR4G MC7824CT MC7824CTG For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NCV devices: Tlow = -40C, Thigh = +125C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control. MARKING DIAGRAMS MC 78xxAyT AWLYWWG MC 78xxyT AWLYWWG * MC 78xxAyD2T AWLYWWG MC 78xxyD2T AWLYWWG * D2PAK-3 D2T SUFFIX CASE 936 TO-220-3 T SUFFIX CASE 221A *This marking diagram also applies to NCV78xx family. xx y A WL, L Y WW G = 05, 06, 08, 09, 12, 15, 18, or 24 = B or C = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Device http://onsemi.com 29 78xxyG ALYWW DPAK-3 DT SUFFIX CASE 369C MC7800, MC7800A, NCV7805 PACKAGE DIMENSIONS TO-220, SINGLE GAUGE T SUFFIX CASE 221AB-01 ISSUE O -TB SEATING PLANE C F T S 4 DIM A B C D F G H J K L N Q R S T U V Z A Q 1 2 3 U H K Z L R V NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE ALLOWED. J G D N http://onsemi.com 30 INCHES MIN MAX 0.570 0.620 0.380 0.405 0.160 0.190 0.025 0.035 0.142 0.147 0.095 0.105 0.110 0.155 0.018 0.025 0.500 0.562 0.045 0.060 0.190 0.210 0.100 0.120 0.080 0.110 0.020 0.055 0.235 0.255 0.000 0.050 0.045 ----0.080 MILLIMETERS MIN MAX 14.48 15.75 9.66 10.28 4.07 4.82 0.64 0.88 3.61 3.73 2.42 2.66 2.80 3.93 0.46 0.64 12.70 14.27 1.15 1.52 4.83 5.33 2.54 3.04 2.04 2.79 0.508 1.39 5.97 6.47 0.00 1.27 1.15 ----2.04 MC7800, MC7800A, NCV7805 PACKAGE DIMENSIONS D2PAK-3 D2T SUFFIX CASE 936-03 ISSUE B -TK OPTIONAL CHAMFER A TERMINAL 4 E U S B F V H 1 2 3 M J D 0.010 (0.254) M T NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS A AND K. 4. DIMENSIONS U AND V ESTABLISH A MINIMUM MOUNTING SURFACE FOR TERMINAL 4. 5. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH OR GATE PROTRUSIONS. MOLD FLASH AND GATE PROTRUSIONS NOT TO EXCEED 0.025 (0.635) MAXIMUM. L P N G DIM A B C D E F G H J K L M N P R S U V R C SOLDERING FOOTPRINT* 8.38 0.33 1.016 0.04 10.66 0.42 5.08 0.20 3.05 0.12 17.02 0.67 D2PAK-3 SCALE 3:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 31 INCHES MIN MAX 0.386 0.403 0.356 0.368 0.170 0.180 0.026 0.036 0.045 0.055 0.051 REF 0.100 BSC 0.539 0.579 0.125 MAX 0.050 REF 0.000 0.010 0.088 0.102 0.018 0.026 0.058 0.078 5 _ REF 0.116 REF 0.200 MIN 0.250 MIN MILLIMETERS MIN MAX 9.804 10.236 9.042 9.347 4.318 4.572 0.660 0.914 1.143 1.397 1.295 REF 2.540 BSC 13.691 14.707 3.175 MAX 1.270 REF 0.000 0.254 2.235 2.591 0.457 0.660 1.473 1.981 5 _ REF 2.946 REF 5.080 MIN 6.350 MIN MC7800, MC7800A, NCV7805 PACKAGE DIMENSIONS DPAK-3 DT SUFFIX CASE 369C-01 ISSUE O C B V NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. SEATING PLANE -T- E R 4 Z A S 1 2 DIM A B C D E F G H J K L R S U V Z 3 U K F J L H D G 2 PL 0.13 (0.005) M INCHES MIN MAX 0.235 0.245 0.250 0.265 0.086 0.094 0.027 0.035 0.018 0.023 0.037 0.045 0.180 BSC 0.034 0.040 0.018 0.023 0.102 0.114 0.090 BSC 0.180 0.215 0.025 0.040 0.020 --0.035 0.050 0.155 --- MILLIMETERS MIN MAX 5.97 6.22 6.35 6.73 2.19 2.38 0.69 0.88 0.46 0.58 0.94 1.14 4.58 BSC 0.87 1.01 0.46 0.58 2.60 2.89 2.29 BSC 4.57 5.45 0.63 1.01 0.51 --0.89 1.27 3.93 --- T SOLDERING FOOTPRINT* 6.20 0.244 3.0 0.118 2.58 0.101 5.80 0.228 1.6 0.063 6.172 0.243 SCALE 3:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 32 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC7800/D