2GB (x72, ECC, SR) 244-Pin DDR3 SDRAM ULP Mini-UDIMM Features DDR3 SDRAM ULP Mini-UDIMM MT9JBF25672AKZ - 2GB Features Figure 1: 244-Pin ULP Mini-UDIMM * DDR3 functionality and operations supported as defined in the component data sheet * 244-pin, ultra-low profile, 17.9mm, mini-unbuffered dual in-line memory module (ULP Mini-UDIMM) * Fast data transfer rates: PC3-12800, PC3-10600, PC3-8500, or PC3-6400 * 2GB (256 Meg x 72) * VDD = 1.5V 0.075V * VDDSPD = 3.0-3.6V * Supports ECC error detection and correction * Nominal and dynamic on-die termination (ODT) for data, strobe, and mask signals * Single-rank * On-board I2C temperature sensor with integrated serial presence-detect (SPD) EEPROM * 8 internal device banks * Fixed burst chop (BC) of 4 and burst length (BL) of 8 via the mode register set (MRS) * Selectable BC4 or BL8 on-the-fly (OTF) * Gold edge contacts * Halogen-free * Fly-by topology * Terminated control, command, and address bus Module height: 17.9mm (0.705in) Options Marking * Operating temperature - Commercial (0C T A +70C) - Industrial (-40C T A +85C)1 * Package - 244-pin halogen-free ULP MiniUDIMM * Frequency/CAS latency - 1.25ns @ CL = 11 (DDR3-1600) - 1.5ns @ CL = 9 (DDR3-1333) - 1.87ns @ CL = 7 (DDR3-1066) Note: None I Z -1G6 -1G4 -1G1 1. Contact Micron for industrial temperature module offerings. Table 1: Key Timing Parameters Data Rate (MT/s) tRCD tRP tRC Speed Grade Industry Nomenclature CL = 9 CL = 8 CL = 7 CL = 6 CL = 5 (ns) (ns) (ns) -1G6 PC3-12800 1600 1333 1333 1066 1066 800 667 13.125 13.125 48.125 -1G4 PC3-10600 - 1333 1333 1066 1066 800 667 13.125 13.125 49.125 -1G1 PC3-8500 - - - 1066 1066 800 667 13.125 13.125 50.625 -1G0 PC3-8500 - - - 1066 - 800 667 15 15 52.5 -80B PC3-6400 - - - - - 800 667 15 15 52.5 1 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2010 Micron Technology, Inc. All rights reserved. PDF: 09005aef83e0c154 jbf9c256x72akz.pdf - Rev. F 5/13 EN CL = 11 CL = 10 Products and specifications discussed herein are subject to change by Micron without notice. 2GB (x72, ECC, SR) 244-Pin DDR3 SDRAM ULP Mini-UDIMM Features Table 2: Addressing Parameter 2GB Refresh count 8K Row address 32K A[14:0] Device bank address 8 BA[2:0] Device configuration 2Gb (256 Meg x 8) Column address 1K A[9:0] Module rank address 1 S0# Table 3: Part Numbers and Timing Parameters - 2GB Modules Base device: MT41J256M8,1 2Gb DDR3 SDRAM Module Part Number2 Density Configuration Module Bandwidth Memory Clock/ Data Rate Clock Cycles (CL-tRCD-tRP) MT9JBF25672AK(I)Z-1G6__ 2GB 256 Meg x 72 12.8 GB/s 1.25ns/1600 MT/s 11-11-11 MT9JBF25672AK(I)Z-1G4__ 2GB 256 Meg x 72 10.6 GB/s 1.5ns/1333 MT/s 9-9-9 MT9JBF25672AK(I)Z-1G1__ 2GB 256 Meg x 72 8.5 GB/s 1.87ns/1066 MT/s 7-7-7 Notes: 1. The data sheet for the base device can be found on Micron's Web site. 2. All part numbers end with a two-place code (not shown) that designates component and PCB revisions. Consult factory for current revision codes. Example: MT9JBF25672AKZ-1G4K1. PDF: 09005aef83e0c154 jbf9c256x72akz.pdf - Rev. F 5/13 EN 2 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2010 Micron Technology, Inc. All rights reserved. 2GB (x72, ECC, SR) 244-Pin DDR3 SDRAM ULP Mini-UDIMM Pin Assignments Pin Assignments Table 4: Pin Assignments 244-Pin DDR3 Mini-UDIMM Front 244-Pin DDR3 Mini-UDIMM Back Pin Symbol Pin Symbol Pin Symbol Pin Symbol Pin Symbol Pin Symbol Pin Symbol Pin Symbol 1 VTT 31 DQ24 61 VDD 92 DQ40 123 VTT 153 DQ29 183 A3 214 DQ45 2 VREFDQ 32 DQ25 62 A2 93 DQ41 124 VSS 154 VSS 184 A1 215 VSS 3 VSS 33 VSS 63 VDD 94 VSS 125 DQ4 155 DM3 185 VDD 216 DM5 4 DQ0 34 DQS3# 64 CK1 95 DQS5# 126 DQ5 156 NC 186 CK0 217 NC 5 DQ1 35 DQS3 65 CK1# 96 DQS5 127 VSS 157 VSS 187 CK0# 218 VSS 6 VSS 36 VSS 66 VDD 97 VSS 128 DM0 158 DQ30 188 VDD 219 DQ46 7 DQS0# 37 DQ26 67 VREFCA 98 DQ42 129 NC 159 DQ31 189 VDD 220 DQ47 8 DQS0 38 DQ27 68 VDD 99 DQ43 130 VSS 160 VSS 190 EVENT# 221 VSS 9 VSS 39 VSS 69 NC 100 VSS 131 DQ6 161 CB4 191 A0 222 DQ52 10 DQ2 40 CB0 70 VDD 101 DQ48 132 DQ7 162 CB5 192 VDD 223 DQ53 11 DQ3 41 CB1 71 A10 102 DQ49 133 VSS 163 VSS 193 BA1 224 VSS 12 VSS 42 VSS 72 BA0 103 VSS 134 DQ12 164 DM8 194 VDD 225 DM6 13 DQ8 43 DQS8# 73 VDD 104 DQS6# 135 DQ13 165 NC 195 RAS# 226 NC 14 DQ9 44 DQS8 74 WE# 105 DQS6 136 VSS 166 VSS 196 CS0# 227 VSS 15 VSS 45 VSS 75 CAS# 106 VSS 137 DM1 167 CB6 197 VDD 228 DQ54 16 DQS1# 46 CB2 76 VDD 107 DQ50 138 NC 168 CB7 198 ODT0 229 DQ55 17 DQS1 47 CB3 77 NC 108 DQ51 139 VSS 169 VSS 199 A13 230 VSS 18 VSS 48 VSS 78 NC 109 VSS 140 DQ14 170 NC 200 VDD 231 DQ60 19 DQ10 49 NC 79 VDD 110 DQ56 141 DQ15 171 NC 201 NC 232 DQ61 20 DQ11 50 RESET# 80 NC 111 DQ57 142 VSS 172 NC 202 NC 233 VSS 21 VSS 51 CKE0 81 NC 112 VSS 143 DQ20 173 VDD 203 VSS 234 DM7 22 DQ16 52 VDD 82 VSS 113 DQS7# 144 DQ21 174 NC 204 DQ36 235 NC 23 DQ17 53 BA2 83 DQ32 114 DQS7 145 VSS 175 A14 205 DQ37 236 VSS 24 VSS 54 NC 84 DQ33 115 VSS 146 DM2 176 VDD 206 VSS 237 DQ62 25 DQS2# 55 VDD 85 VSS 116 DQ58 147 NC 177 A12 207 DM4 238 DQ63 26 DQS2 56 A11 86 DQS4# 117 DQ59 148 VSS 178 A9 208 NC 239 VSS 27 VSS 57 A7 87 DQS4 118 VSS 149 DQ22 179 VDD 209 VSS 240 VDDSPD 28 DQ18 58 VDD 88 VSS 119 SA0 150 DQ23 180 A8 210 DQ38 241 SA1 29 DQ19 59 A5 89 DQ34 120 SCL 151 VSS 181 A6 211 DQ39 242 SDA 30 VSS 60 A4 90 DQ35 121 SA2 152 DQ28 182 VDD 212 VSS 243 VSS 91 VSS 122 VTT 213 DQ44 244 VTT PDF: 09005aef83e0c154 jbf9c256x72akz.pdf - Rev. F 5/13 EN 3 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2010 Micron Technology, Inc. All rights reserved. 2GB (x72, ECC, SR) 244-Pin DDR3 SDRAM ULP Mini-UDIMM Pin Descriptions Pin Descriptions The pin description table below is a comprehensive list of all possible pins for all DDR3 modules. All pins listed may not be supported on this module. See Pin Assignments for information specific to this module. Table 5: Pin Descriptions Symbol Type Description Ax Input Address inputs: Provide the row address for ACTIVE commands, and the column address and auto precharge bit (A10) for READ/WRITE commands, to select one location out of the memory array in the respective bank. A10 sampled during a PRECHARGE command determines whether the PRECHARGE applies to one bank (A10 LOW, bank selected by BAx) or all banks (A10 HIGH). The address inputs also provide the op-code during a LOAD MODE command. See the Pin Assignments Table for density-specific addressing information. BAx Input Bank address inputs: Define the device bank to which an ACTIVE, READ, WRITE, or PRECHARGE command is being applied. BA define which mode register (MR0, MR1, MR2, or MR3) is loaded during the LOAD MODE command. CKx, CKx# Input Clock: Differential clock inputs. All control, command, and address input signals are sampled on the crossing of the positive edge of CK and the negative edge of CK#. CKEx Input Clock enable: Enables (registered HIGH) and disables (registered LOW) internal circuitry and clocks on the DRAM. DMx Input Data mask (x8 devices only): DM is an input mask signal for write data. Input data is masked when DM is sampled HIGH, along with that input data, during a write access. Although DM pins are input-only, DM loading is designed to match that of the DQ and DQS pins. ODTx Input On-die termination: Enables (registered HIGH) and disables (registered LOW) termination resistance internal to the DDR3 SDRAM. When enabled in normal operation, ODT is only applied to the following pins: DQ, DQS, DQS#, DM, and CB. The ODT input will be ignored if disabled via the LOAD MODE command. Par_In Input Parity input: Parity bit for Ax, RAS#, CAS#, and WE#. RAS#, CAS#, WE# Input Command inputs: RAS#, CAS#, and WE# (along with S#) define the command being entered. RESET# Input (LVCMOS) Reset: RESET# is an active LOW asychronous input that is connected to each DRAM and the registering clock driver. After RESET# goes HIGH, the DRAM must be reinitialized as though a normal power-up was executed. Sx# Input Chip select: Enables (registered LOW) and disables (registered HIGH) the command decoder. SAx Input Serial address inputs: Used to configure the temperature sensor/SPD EEPROM address range on the I2C bus. SCL Input Serial clock for temperature sensor/SPD EEPROM: Used to synchronize communication to and from the temperature sensor/SPD EEPROM on the I2C bus. CBx I/O Check bits: Used for system error detection and correction. DQx I/O Data input/output: Bidirectional data bus. DQSx, DQSx# I/O Data strobe: Differential data strobes. Output with read data; edge-aligned with read data; input with write data; center-aligned with write data. PDF: 09005aef83e0c154 jbf9c256x72akz.pdf - Rev. F 5/13 EN 4 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2010 Micron Technology, Inc. All rights reserved. 2GB (x72, ECC, SR) 244-Pin DDR3 SDRAM ULP Mini-UDIMM Pin Descriptions Table 5: Pin Descriptions (Continued) Symbol Type SDA I/O Description Serial data: Used to transfer addresses and data into and out of the temperature sensor/SPD EEPROM on the I2C bus. TDQSx, TDQSx# Output Redundant data strobe (x8 devices only): TDQS is enabled/disabled via the LOAD MODE command to the extended mode register (EMR). When TDQS is enabled, DM is disabled and TDQS and TDQS# provide termination resistance; otherwise, TDQS# are no function. Err_Out# Output Parity error output: Parity error found on the command and address bus. (open drain) EVENT# Output Temperature event:The EVENT# pin is asserted by the temperature sensor when criti(open drain) cal temperature thresholds have been exceeded. VDD Supply Power supply: 1.5V 0.075V. The component VDD and VDDQ are connected to the module VDD. VDDSPD Supply Temperature sensor/SPD EEPROM power supply: 3.0-3.6V. VREFCA Supply Reference voltage: Control, command, and address VDD/2. VREFDQ Supply Reference voltage: DQ, DM VDD/2. VSS Supply Ground. VTT Supply Termination voltage: Used for control, command, and address VDD/2. NC - No connect: These pins are not connected on the module. NF - No function: These pins are connected within the module, but provide no functionality. PDF: 09005aef83e0c154 jbf9c256x72akz.pdf - Rev. F 5/13 EN 5 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2010 Micron Technology, Inc. All rights reserved. 2GB (x72, ECC, SR) 244-Pin DDR3 SDRAM ULP Mini-UDIMM DQ Map DQ Map Table 6: Component-to-Module DQ Map Component Reference Number Component DQ U1 U4 U6 U8 PDF: 09005aef83e0c154 jbf9c256x72akz.pdf - Rev. F 5/13 EN Module DQ Module Pin Number Component Reference Number Component DQ Module DQ Module Pin Number 0 6 131 U2 0 18 28 1 1 5 1 21 144 2 3 11 2 23 150 3 5 126 3 17 23 4 2 10 4 22 149 5 4 125 5 16 22 6 7 132 6 19 29 7 0 4 7 20 143 8 34 89 0 50 107 U5 9 37 205 1 53 223 10 39 211 2 55 229 11 33 84 3 49 102 12 38 210 4 54 228 13 32 83 5 48 101 14 35 90 6 51 108 15 36 204 7 52 222 0 61 232 0 45 214 1 62 237 1 46 219 2 56 110 2 40 92 3 59 117 3 43 99 4 60 231 4 44 213 5 63 238 5 47 220 6 57 111 6 41 93 7 58 116 7 42 98 0 CB0 40 0 29 153 1 CB1 41 1 30 158 2 CB2 46 2 24 31 3 CB3 47 3 27 38 4 CB4 161 4 28 152 5 CB5 162 5 31 159 6 CB6 167 6 25 32 7 CB7 168 7 26 37 U7 U9 6 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2010 Micron Technology, Inc. All rights reserved. 2GB (x72, ECC, SR) 244-Pin DDR3 SDRAM ULP Mini-UDIMM DQ Map Table 6: Component-to-Module DQ Map (Continued) Component Reference Number Component DQ Module DQ Module Pin Number U10 0 9 14 1 14 140 2 12 134 3 11 20 4 8 13 5 15 141 6 13 135 7 10 19 PDF: 09005aef83e0c154 jbf9c256x72akz.pdf - Rev. F 5/13 EN Component Reference Number 7 Component DQ Module DQ Module Pin Number Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2010 Micron Technology, Inc. All rights reserved. 2GB (x72, ECC, SR) 244-Pin DDR3 SDRAM ULP Mini-UDIMM Functional Block Diagram Functional Block Diagram Figure 2: Functional Block Diagram S0# DQS0# DQS0 DM0 DQS4# DQS4 DM4 DM CS# DQ DQS# DQS1# DQS1 DM1 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ DQ DQ DQ DQ DQ DQ DQ DM U1 ZQ VSS DQS5# DQS5 DM5 DQ32 DQ33 DQ34 DQ35 DQ36 DQ37 DQ38 DQ39 DQS2# DQS2 DM2 DQ DQ DQ DQ DQ DQ DQ DQ U10 ZQ DQS6# DQS6 DM6 DQS3# DQS3 DM3 ZQ VSS DQS7# DQS7 DM7 DQ DQ DQ DQ DQ DQ DQ DQ U9 ZQ DQS8# DQS8 DM8 SCL U8 DDR3 SDRAM X 9 VDD VREFCA U9 Temperature Sensor/ SPD EEPROM DDR3 SDRAM Control, command, and address termination DDR3 SDRAM VREFDQ DDR3 SDRAM VSS DDR3 SDRAM ZQ VSS DM CS# DQ DQS# DQ DQ DQ DQ DQ DQ DQ DQ VDDSPD VTT CS# DQ DQS# VSS CB0 CB1 CB2 CB3 CB4 CB5 CB6 CB7 VDD CK1 CK1# ZQ DQ DQ DQ DQ DQ DQ DQ DQ DQ56 DQ57 DQ58 DQ59 DQ60 DQ61 DQ62 DQ63 DDR3 SDRAM CK0 CK0# U5 DM VTT CK CK# CS# DQ DQS# VSS DM CS# DQ DQS# DQ24 DQ25 DQ26 DQ27 DQ28 DQ29 DQ30 DQ31 ZQ DQ DQ DQ DQ DQ DQ DQ DQ DDR3 SDRAM CKE0, A[14:0], RAS#, CAS#, WE#, ODT0, BA[2:0], S0# U7 DM U2 Clock, control, command, and address line terminations: VSS DQ48 DQ49 DQ50 DQ51 DQ52 DQ53 DQ54 DQ55 BA[2:0]: DDR3 SDRAM A[14:0]: DDR3 SDRAM RAS#: DDR3 SDRAM CAS#: DDR3 SDRAM WE#: DDR3 SDRAM CKE0: DDR3 SDRAM ODT0: DDR3 SDRAM RESET#: DDR3 SDRAM CS# DQ DQS# DQ DQ DQ DQ DQ DQ DQ DQ DQ40 DQ41 DQ42 DQ43 DQ44 DQ45 DQ46 DQ47 DM CS# DQ DQS# DQ DQ DQ DQ DQ DQ DQ DQ ZQ DM VSS DQ16 DQ17 DQ18 DQ19 DQ20 DQ21 DQ22 DQ23 U4 VSS DM CS# DQ DQS# DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 BA[2:0] A[14:0] RAS# CAS# WE# CKE0 ODT0 RESET# CS# DQ DQS# DQ DQ DQ DQ DQ DQ DQ DQ U3 Temperature sensor/ SPD EEPROM EVT A0 SDA A1 A2 SA0 SA1 SA2 EVENT# ZQ VSS Note: PDF: 09005aef83e0c154 jbf9c256x72akz.pdf - Rev. F 5/13 EN 1. The ZQ ball on each DDR3 component is connected to an external 240 1% resistor that is tied to ground. It is used for the calibration of the component's ODT and output driver. 8 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2010 Micron Technology, Inc. All rights reserved. 2GB (x72, ECC, SR) 244-Pin DDR3 SDRAM ULP Mini-UDIMM General Description General Description DDR3 SDRAM modules are high-speed, CMOS dynamic random access memory modules that use internally configured 8-bank DDR3 SDRAM devices. DDR3 SDRAM modules use DDR architecture to achieve high-speed operation. DDR3 architecture is essentially an 8n-prefetch architecture with an interface designed to transfer two data words per clock cycle at the I/O pins. A single read or write access for the DDR3 SDRAM module effectively consists of a single 8n-bit-wide, one-clock-cycle data transfer at the internal DRAM core and eight corresponding n-bit-wide, one-half-clock-cycle data transfers at the I/O pins. DDR3 modules use two sets of differential signals: DQS, DQS# to capture data and CK and CK# to capture commands, addresses, and control signals. Differential clocks and data strobes ensure exceptional noise immunity for these signals and provide precise crossing points to capture input signals. Fly-By Topology DDR3 modules use faster clock speeds than earlier DDR technologies, making signal quality more important than ever. For improved signal quality, the clock, control, command, and address buses have been routed in a fly-by topology, where each clock, control, command, and address pin on each DRAM is connected to a single trace and terminated (rather than a tree structure, where the termination is off the module near the connector). Inherent to fly-by topology, the timing skew between the clock and DQS signals can be easily accounted for by using the write-leveling feature of DDR3. Temperature Sensor with Serial Presence-Detect EEPROM Thermal Sensor Operations The temperature from the integrated thermal sensor is monitored and converts into a digital word via the I2C bus. System designers can use the user-programmable registers to create a custom temperature-sensing solution based on system requirements. Programming and configuration details comply with JEDEC standard No. 21-C page 4.7-1, "Definition of the TSE2002av, Serial Presence Detect with Temperature Sensor." Serial Presence-Detect EEPROM Operation DDR3 SDRAM modules incorporate serial presence-detect. The SPD data is stored in a 256-byte EEPROM. The first 128 bytes are programmed by Micron to comply with JEDEC standard JC-45, "Appendix X: Serial Presence Detect (SPD) for DDR3 SDRAM Modules." These bytes identify module-specific timing parameters, configuration information, and physical attributes. The remaining 128 bytes of storage are available for use by the customer. System READ/WRITE operations between the master (system logic) and the slave EEPROM device occur via a standard I2C bus using the DIMM's SCL (clock) SDA (data), and SA (address) pins. Write protect (WP) is connected to V SS, permanently disabling hardware write protection. For further information refer to Micron technical note TN-04-42, "Memory Module Serial Presence-Detect." PDF: 09005aef83e0c154 jbf9c256x72akz.pdf - Rev. F 5/13 EN 9 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2010 Micron Technology, Inc. All rights reserved. 2GB (x72, ECC, SR) 244-Pin DDR3 SDRAM ULP Mini-UDIMM Electrical Specifications Electrical Specifications Stresses greater than those listed may cause permanent damage to the module. This is a stress rating only, and functional operation of the module at these or any other conditions outside those indicated in each device's data sheet is not implied. Exposure to absolute maximum rating conditions for extended periods may adversely affect reliability. Table 7: Absolute Maximum Ratings Symbol Parameter Min Max Units VDD VDD supply voltage relative to VSS -0.4 1.975 V VIN, VOUT Voltage on any pin relative to VSS -0.4 1.975 V Table 8: Operating Conditions Symbol Parameter Min Nom Max Units 1.425 1.5 1.575 V VREFCA(DC) Input reference voltage command/address bus 0.49 x VDD 0.5 x VDD 0.51 x VDD V VREFDQ(DC) I/O reference voltage DQ bus 0.49 x VDD 0.5 x VDD 0.51 x VDD V -600 - +600 mA 0.49 x VDD 20mV 0.5 x VDD 0.51 x VDD + 20mV V A VDD VDD supply voltage IVTT Termination reference current from VTT VTT Termination reference voltage (DC) - command/address bus II Notes 1 Input leakage current; Any input 0V VIN VDD; VREF input 0V VIN 0.95V (All other pins not under test = 0V) Address inputs, RAS#,CAS#, WE#, S#, CKE, ODT, BA, CK, CK# -18 0 18 DM -2 0 2 IOZ Output leakage current; 0V VOUT VDD; DQ and ODT are disabled; ODT is HIGH DQ, DQS, DQS# -5 0 5 A IVREF VREF supply leakage current; VREFDQ = VDD/2 or VREFCA = VDD/2 (All other pins not under test = 0V) -9 0 9 A 0 - 70 C 2, 3 -40 - 85 0 - 85 C 2, 3, 4 -40 - 95 TA Module ambient operating temperature TC DDR3 SDRAM component case op- Commercial erating temperature Industrial Notes: PDF: 09005aef83e0c154 jbf9c256x72akz.pdf - Rev. F 5/13 EN Commercial Industrial 1. VTT termination voltage in excess of the stated limit will adversely affect the command and address signals' voltage margin and will reduce timing margins. 2. TA and TC are simultaneous requirements. 3. For further information, refer to technical note TN-00-08: "Thermal Applications," available on Micron's Web site. 4. The refresh rate is required to double when 85C < TC 95C. 10 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2010 Micron Technology, Inc. All rights reserved. 2GB (x72, ECC, SR) 244-Pin DDR3 SDRAM ULP Mini-UDIMM DRAM Operating Conditions DRAM Operating Conditions Recommended AC operating conditions are given in the DDR3 component data sheets. Component specifications are available on Micron's web site. Module speed grades correlate with component speed grades, as shown below. Table 9: Module and Component Speed Grades DDR3 components may exceed the listed module speed grades; module may not be available in all listed speed grades Module Speed Grade Component Speed Grade -2G1 -093 -1G9 -107 -1G6 -125 -1G4 -15E -1G1 -187E -1G0 -187 -80C -25E -80B -25 Design Considerations Simulations Micron memory modules are designed to optimize signal integrity through carefully designed terminations, controlled board impedances, routing topologies, trace length matching, and decoupling. However, good signal integrity starts at the system level. Micron encourages designers to simulate the signal characteristics of the system's memory bus to ensure adequate signal integrity of the entire memory system. Power Operating voltages are specified at the DRAM, not at the edge connector of the module. Designers must account for any system voltage drops at anticipated power levels to ensure the required supply voltage is maintained. PDF: 09005aef83e0c154 jbf9c256x72akz.pdf - Rev. F 5/13 EN 11 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2010 Micron Technology, Inc. All rights reserved. 2GB (x72, ECC, SR) 244-Pin DDR3 SDRAM ULP Mini-UDIMM IDD Specifications IDD Specifications Table 10: DDR3 IDD Specifications and Conditions - 2GB (Die Revision D) Values are for the MT41J256M8 DDR3 SDRAM only and are computed from values specified in the 2Gb (256 Meg x 8) component data sheet. Parameter Symbol 1600 1333 1066 Units Operating current 0: One bank ACTIVATE-to-PRECHARGE IDD0 855 765 675 mA Operating current 1: One bank ACTIVATE-to-READ-to-PRECHARGE IDD1 945 900 855 mA Precharge power-down current: Slow exit IDD2P0 108 180 108 mA Precharge power-down current: Fast exit IDD2P1 315 270 225 mA Precharge quiet standby current IDD2Q 360 315 270 mA Precharge standby current IDD2N 378 333 288 mA Precharge standby ODT current IDD2NT 450 405 360 mA Active power-down current IDD3P 360 315 270 mA Active standby current IDD3N 405 360 315 mA Burst read operating current IDD4R 1620 1440 1260 mA Burst write operating current IDD4W 1665 1485 1305 mA Refresh current IDD5B 1935 1800 1710 mA Self refresh temperature current: MAX TC = 85C IDD6 108 108 108 mA Self refresh temperature current (SRT-enabled): MAX TC = 95C IDD6ET 135 135 135 mA All banks interleaved read current IDD7 3915 3465 3015 mA Reset current IDD8 126 126 126 mA PDF: 09005aef83e0c154 jbf9c256x72akz.pdf - Rev. F 5/13 EN 12 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2010 Micron Technology, Inc. All rights reserved. 2GB (x72, ECC, SR) 244-Pin DDR3 SDRAM ULP Mini-UDIMM IDD Specifications Table 11: DDR3 IDD Specifications and Conditions - 2GB (Die Revision K) Values are for the MT41J256M8 DDR3 SDRAM only and are computed from values specified in the 2Gb (256 Meg x 8) component data sheet. Parameter Symbol 1600 1333 1066 Units Operating current 0: One bank ACTIVATE-to-PRECHARGE IDD0 378 369 351 mA Operating current 1: One bank ACTIVATE-to-READ-to-PRECHARGE IDD1 504 486 450 mA Precharge power-down current: Slow exit IDD2P0 108 108 108 mA Precharge power-down current: Fast exit IDD2P1 135 135 135 mA Precharge quiet standby current IDD2Q 198 198 198 mA Precharge standby current IDD2N 207 207 207 mA Precharge standby ODT current IDD2NT 306 288 261 mA Active power-down current IDD3P 198 198 198 mA Active standby current IDD3N 315 297 279 mA Burst read operating current IDD4R 900 792 675 mA Burst write operating current IDD4W 927 819 711 mA Refresh current IDD5B 1638 1629 1611 mA Self refresh temperature current: MAX TC = 85C IDD6 108 108 108 mA Self refresh temperature current (SRT-enabled): MAX TC = 95C IDD6ET 135 135 135 mA All banks interleaved read current IDD7 1467 1413 1152 mA Reset current IDD8 126 126 126 mA PDF: 09005aef83e0c154 jbf9c256x72akz.pdf - Rev. F 5/13 EN 13 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2010 Micron Technology, Inc. All rights reserved. 2GB (x72, ECC, SR) 244-Pin DDR3 SDRAM ULP Mini-UDIMM Temperature Sensor with Serial Presence-Detect EEPROM Temperature Sensor with Serial Presence-Detect EEPROM The temperature sensor continuously monitors the module's temperature and can be read back at any time over the I2C bus shared with the SPD EEPROM. Refer to JEDEC standard No. 21-C page 4.7-1, "Definition of the TSE2002av, Serial Presence Detect with Temperature Sensor." Serial Presence-Detect For the latest SPD data, refer to Micron's SPD page: www.micron.com/SPD. Table 12: Temperature Sensor with SPD EEPROM Operating Conditions Parameter/Condition Symbol Min Max Units VDDSPD 3.0 3.6 V Supply current: VDD = 3.3V IDD - 2.0 mA Input high voltage: Logic 1; SCL, SDA VIH VDDSPD x 0.7 VDDSPD + 1 V Input low voltage: Logic 0; SCL, SDA VIL -0.5 VDDSPD x 0.3 V Output low voltage: IOUT = 2.1mA VOL - 0.4 V Input current IIN -5.0 5.0 A Temperature sensing range - -40 125 C Temperature sensor accuracy (class B) - -1.0 1.0 C Supply voltage Table 13: Temperature Sensor and SPD EEPROM Serial Interface Timing Parameter/Condition Symbol Min Max Units tBUF 4.7 - s SDA fall time tF 20 300 ns SDA rise time tR - 1000 ns tHD:DAT 200 900 ns Time bus must be free before a new transition can start Data hold time Start condition hold time tH:STA 4.0 - s Clock HIGH period tHIGH 4.0 50 s Clock LOW period tLOW 4.7 - s tSCL 10 100 kHz Data setup time tSU:DAT 250 - ns Start condition setup time tSU:STA 4.7 - s Stop condition setup time tSU:STO 4.0 - s SCL clock frequency PDF: 09005aef83e0c154 jbf9c256x72akz.pdf - Rev. F 5/13 EN 14 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2010 Micron Technology, Inc. All rights reserved. 2GB (x72, ECC, SR) 244-Pin DDR3 SDRAM ULP Mini-UDIMM Temperature Sensor with Serial Presence-Detect EEPROM EVENT# Pin The temperature sensor also adds the EVENT# pin (open-drain). Not used by the SPD EEPROM, EVENT# is a temperature sensor output used to flag critical events that can be set up in the sensor's configuration register. EVENT# has three defined modes of operation: interrupt mode, compare mode, and critical temperature mode. Event thresholds are programmed in the 0x01 register using a hysteresis. The alarm window provides a comparison window, with upper and lower limits set in the alarm upper boundary register and the alarm lower boundary register, respectively. When the alarm window is enabled, EVENT# will trigger whenever the temperature is outside the MIN or MAX values set by the user. The interrupt mode enables software to reset EVENT# after a critical temperature threshold has been detected. Threshold points are set in the configuration register by the user. This mode triggers the critical temperature limit and both the MIN and MAX of the temperature window. The compare mode is similar to the interrupt mode, except EVENT# cannot be reset by the user and returns to the logic HIGH state only when the temperature falls below the programmed thresholds. Critical temperature mode triggers EVENT# only when the temperature has exceeded the programmed critical trip point. When the critical trip point has been reached, the temperature sensor goes into comparator mode, and the critical EVENT# cannot be cleared through software. PDF: 09005aef83e0c154 jbf9c256x72akz.pdf - Rev. F 5/13 EN 15 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2010 Micron Technology, Inc. All rights reserved. 2GB (x72, ECC, SR) 244-Pin DDR3 SDRAM ULP Mini-UDIMM Module Dimensions Module Dimensions Figure 3: 244-Pin DDR3 ULP Mini-UDIMM Front view 3.80 (0.15) MAX 82.15 (3.234) 81.85 (3.222) 1.0 (0.039) R X2 U3 U1 1.8 (0.071) D X2 U4 U2 U5 10.0 (0.394) TYP 6.0 (0.236) TYP 1.0 (0.039) TYP 2.0 (0.079) TYP Pin 1 0.5 (0.02) R 0.6 (0.024) 0.45 (0.018) TYP TYP 43.9 (1.73) TYP Pin 122 17.91 (0.705) 17.89 (0.704) 1.1 (0.043) 0.9 (0.035) 78.0 (3.071) TYP Back view 45 X4 U7 U6 U8 U10 U9 3.3 (0.13) TYP 3.6 (0.142) TYP Pin 244 3.2 (0.126) TYP 33.6 (1.323) TYP Notes: Pin 123 38.4 (1.512) TYP 1. All dimensions are in millimeters (inches); MAX/MIN or typical (TYP) where noted. 2. The dimensional diagram is for reference only. 8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-3900 www.micron.com/productsupport Customer Comment Line: 800-932-4992 Micron and the Micron logo are trademarks of Micron Technology, Inc. All other trademarks are the property of their respective owners. This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein. Although considered final, these specifications are subject to change, as further product development and data characterization sometimes occur. PDF: 09005aef83e0c154 jbf9c256x72akz.pdf - Rev. F 5/13 EN 16 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2010 Micron Technology, Inc. All rights reserved.