HCPL-2231 - Hewlett-Packard / Agilent - Datasheet.Directory

Very High CMR, Wide VCC Logic

Gate Optocouplers

Technical Data HCPL-2201 HCPL-2202

HCPL-2211 HCPL-2212

HCPL-2231 HCPL-2232

HCPL-0201 HCPL-0211

HCNW2201 HCNW2211

Features

• 10 kV/µs Minimum Common

Mode Rejection (CMR) at

V

CM = 1000 V

(HCPL-2211/2212/0211/

2232, HCNW2211)

• Wide Operating V

CC Range:

4.5 to 20 Volts

• 300 ns Propagation Delay

Guaranteed over the Full

Temperature Range

• 5 Mbd Typical Signal Rate

• Low Input Current (1.6 mA

to 1.8 mA)

• Hysteresis

• Totem Pole Output (No

Pullup Resistor Required)

• Available in 8-Pin DIP,

SOIC-8, Widebody Packages

• Guaranteed Performance

from -40°C to 85°C

• Safety Approval

UL Recognized -3750 V rms

for 1 minute (5000 V rms

for 1 minute for

HCNW22XX) per UL1577

CSA Approved

IEC/EN/DIN EN 60747-5-2

Approved with VIORM = 630

V peak (HCPL-2211/2212 Option

060 only) and VIORM = 1414

V peak (HCNW22XX only)

• MIL-PRF-38534 Hermetic

Version Available

(HCPL-52XX/62XX)

Applications

• Isolation of High Speed

Logic Systems

• Computer-Peripheral

Interfaces

• Microprocessor System

Interfaces

• Ground Loop Elimination

• Pulse Transformer

Replacement

• High Speed Line Receiver

• Power Control Systems

Description

The HCPL-22XX, HCPL-02XX,

and HCNW22XX are optically-

coupled logic gates. The

HCPL-22XX, and HCPL-02XX

contain a GaAsP LED while the

HCNW22XX contains an AlGaAs

LED. The detectors have totem

pole output stages and optical

receiver input stages with built-in

Schmitt triggers to provide logic-

compatible waveforms, eliminat-

ing the need for additional

waveshaping.

A superior internal shield on the

HCPL-2211/12, HCPL-0211,

CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component

to prevent damage and/or degradation which may be induced by ESD.

Functional Diagram

A 0.1 µF bypass capacitor must be connected between pins 5 and 8.

7

1

2

3

45

6

8

NC

ANODE

CATHODE

NC GND

VCC

VO

NC

SHIELD

HCPL-2201/11

HCPL-0201/11

HCNW2201/11

7

1

2

3

45

6

8

NC

ANODE

CATHODE

NC GND

VCC

VO

NC

SHIELD

HCPL-2202/12

7

1

2

3

45

6

8

ANODE 1

CATHODE 1

CATHODE 2

ANODE 2 GND

VCC

VO1

VO2

SHIELD

HCPL-2231/32

TRUTH TABLE

(POSITIVE LOGIC)

LED

ON

OFF

VO

HIGH

LOW

2

Selection Guide

Small- Widebody

Minimum CMR Input 8-Pin DIP (300 Mil) Outline SO-8 (400 Mil) Hermetic

On- Single Dual Single Single Single and

dV/dt Current Channel Channel Channel Channel Dual Channel

(V/µs) VCM (V) (mA) Package Package Package Package Packages

1,000 50 1.6 HCPL-2200[1,2] HCPL-0201 HCNW2201

HCPL-2201

HCPL-2202

1.8 HCPL-2231

2,500 400 1.6 HCPL-2219[1,2]

5,000[3] 300[3] 1.6 HCPL-2211 HCPL-0211 HCNW2211

HCPL-2212

1.8 HCPL-2232

1,000 50 2.0 HCPL-52XX[2]

HCPL-62XX[2]

Notes:

1. HCPL-2200/2219 devices include output enable/disable function.

2. Technical data for the HCPL-2200/2219, HCPL-52XX and HCPL-62XX are on separate Agilent publications.

3. Minimum CMR of 10 kV/µs with V

CM = 1000 V can be achieved with input current, IF, of 5 mA.

Ordering Information

Specify Part Number followed by Option Number (if desired).

Example:

HCPL-2211#XXXX

060 = IEC/EN/DIN EN 60747-5-2 VIORM = 630 V peak Option*

300 = Gull Wing Surface Mount Option**

500 = Tape and Reel Packaging Option

XXXE = Lead Free Option

Option data sheets available. Contact your Agilent sales representative or authorized distributor for information.

Remarks: The notation “#” is used for existing products, while (new) products launched since 15th July 2001

and lead free option will use “-”

*For HCPL-2211/2212 only.

**Gull wing surface mount option applies to through hole parts only.

Schematic

HCPL-2201/02/11/12

HCPL-0201/11

HCNW2201/11

I

F

SHIELD

V

F

V

CC

V

O

GND

I

CC

I

O

+

–

2

3

8

5

I

F1

SHIELD

V

F1

V

CC

V

O1

I

CC

I

O1

+

–

1

2

8

6

HCPL-2231/32

SHIELD

V

F2

V

O2

GND

I

O2

–

+

3

4

5

I

F2

7

HCPL-2232 and HCNW2211

guarantees common mode

transient immunity of 10 kV/µs at

a common mode voltage of 1000

volts.

The electrical and switching

characteristics of the HCPL-

22XX, HCPL-02XX and

HCNW22XX are guaranteed from

-40°C to +85°C and a VCC from

4.5 volts to 20 volts. Low IF and

wide V

CC range allow compatibil-

ity with TTL, LSTTL, and CMOS

logic and result in lower power

consumption compared to other

high speed couplers. Logic signals

are transmitted with a typical

propagation delay of 150 ns.

3

Package Outline Drawings

8-Pin DIP Package (HCPL-2201/02/11/12/31/32)

8-Pin DIP Package with Gull Wing Surface Mount Option 300 (HCPL-2201/02/11/12/31/32)

1.080 ± 0.320

(0.043 ± 0.013) 2.54 ± 0.25

(0.100 ± 0.010)

0.51 (0.020) MIN.

0.65 (0.025) MAX.

4.70 (0.185) MAX.

2.92 (0.115) MIN.

5° TYP. 0.254 + 0.076

- 0.051

(0.010+ 0.003)

- 0.002)

7.62 ± 0.25

(0.300 ± 0.010)

6.35 ± 0.25

(0.250 ± 0.010)

9.65 ± 0.25

(0.380 ± 0.010)

1.78 (0.070) MAX.

1.19 (0.047) MAX.

A XXXXZ

YYWW

DATE CODE

DIMENSIONS IN MILLIMETERS AND (INCHES).

5678

4321

OPTION CODE*

UL

RECOGNITION

UR

TYPE NUMBER

* MARKING CODE LETTER FOR OPTION NUMBERS

"V" = OPTION 060

OPTION NUMBERS 300 AND 500 NOT MARKED.

NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

3.56 ± 0.13

(0.140 ± 0.005)

0.635 ± 0.25

(0.025 ± 0.010) 12° NOM.

9.65 ± 0.25

(0.380 ± 0.010)

0.635 ± 0.130

(0.025 ± 0.005)

7.62 ± 0.25

(0.300 ± 0.010)

5

6

7

8

4

3

2

1

9.65 ± 0.25

(0.380 ± 0.010)

6.350 ± 0.25

(0.250 ± 0.010)

1.016 (0.040)

1.27 (0.050)

10.9 (0.430)

2.0 (0.080)

LAND PATTERN RECOMMENDATION

1.080 ± 0.320

(0.043 ± 0.013)

3.56 ± 0.13

(0.140 ± 0.005)

1.780

(0.070)

MAX.

1.19

(0.047)

MAX.

2.54

(0.100)

BSC

DIMENSIONS IN MILLIMETERS (INCHES).

LEAD COPLANARITY = 0.10 mm (0.004 INCHES).

NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

0.254 + 0.076

- 0.051

(0.010+ 0.003)

- 0.002)

4

Small-Outline SO-8 Package (HCPL-0201/11)

8-Pin Widebody DIP Package (HCNW2201/11)

XXX

YWW

8765

4321

5.994 ± 0.203

(0.236 ± 0.008)

3.937 ± 0.127

(0.155 ± 0.005)

0.406 ± 0.076

(0.016 ± 0.003) 1.270

(0.050)BSC

5.080 ± 0.127

(0.200 ± 0.005)

3.175 ± 0.127

(0.125 ± 0.005) 1.524

(0.060)

45° X 0.432

(0.017)

0.228 ± 0.025

(0.009 ± 0.001)

TYPE NUMBER

(LAST 3 DIGITS)

DATE CODE

0.305

(0.012)MIN.

TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH)

5.207 ± 0.254 (0.205 ± 0.010)

DIMENSIONS IN MILLIMETERS (INCHES).

LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX.

NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX.

0.203 ± 0.102

(0.008 ± 0.004)

7°

PIN ONE

0 ~ 7°

*

*

7.49 (0.295)

1.9 (0.075)

0.64 (0.025)

LAND PATTERN RECOMMENDATION

5

6

7

8

4

3

2

1

11.15 ± 0.15

(0.442 ± 0.006)

1.78 ± 0.15

(0.070 ± 0.006)

5.10

(0.201)MAX.

1.55

(0.061)

MAX.

2.54 (0.100)

TYP.

DIMENSIONS IN MILLIMETERS (INCHES).

NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

7° TYP. 0.254 + 0.076

- 0.0051

(0.010+ 0.003)

- 0.002)

11.00

(0.433)

9.00 ± 0.15

(0.354 ± 0.006)

MAX.

10.16 (0.400)

TYP.

A

HCNWXXXX

YYWW

DATE CODE

TYPE NUMBER

0.51 (0.021) MIN.

0.40 (0.016)

0.56 (0.022)

3.10 (0.122)

3.90 (0.154)

5

8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW2201/11)

Solder Reflow Temperature Profile

0

TIME (SECONDS)

TEMPERATURE (°C)

200

100

50 150100 200 250

300

0

30

SEC.

50 SEC.

30

SEC.

160°C

140°C

150°C

PEAK

TEMP.

245°C

PEAK

TEMP.

240°C

PEAK

TEMP.

230°C

SOLDERING

TIME

200°C

PREHEATING TIME

150°C, 90 + 30 SEC.

2.5°C ± 0.5°C/SEC.

3°C + 1°C/–0.5°C

TIGHT

TYPICAL

LOOSE

ROOM

TEMPERATURE

PREHEATING RATE 3°C + 1°C/–0.5°C/SEC.

REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC.

1.00 ± 0.15

(0.039 ± 0.006)

7° NOM.

12.30 ± 0.30

(0.484 ± 0.012)

0.75 ± 0.25

(0.030 ± 0.010)

11.00

(0.433)

5

6

7

8

4

3

2

1

11.15 ± 0.15

(0.442 ± 0.006)

9.00 ± 0.15

(0.354 ± 0.006)

1.3

(0.051)

13.56

(0.534)

2.29

(0.09)

LAND PATTERN RECOMMENDATION

1.78 ± 0.15

(0.070 ± 0.006)

4.00

(0.158)MAX.

1.55

(0.061)

MAX.

2.54

(0.100)

BSC

DIMENSIONS IN MILLIMETERS (INCHES).

LEAD COPLANARITY = 0.10 mm (0.004 INCHES).

NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

0.254 + 0.076

- 0.0051

(0.010+ 0.003)

- 0.002)

MAX.

6

Regulatory Information

The HCPL-22XX/02XX and

HCNW22XX have been approved

by the following organizations:

UL

Recognized under UL 1577,

Component Recognition

Program, File E55361.

CSA

Approved under CSA Component

Acceptance Notice #5, File CA

88324.

Insulation and Safety Related Specifications

8-pin DIP Package

8-Pin DIP Widebody

(300 Mil) SO-8 (400 Mil)

Parameter Symbol Value Value Value Units Conditions

Minimum External L(101) 7.1 4.9 9.6 mm Measured from input terminals

Air Gap (External to output terminals, shortest

Clearance) distance through air.

Minimum External L(102) 7.4 4.8 10.0 mm Measured from input terminals

Tracking (External to output terminals, shortest

Creepage) distance path along body.

Minimum Internal 0.08 0.08 1.0 mm Through insulation distance,

Plastic Gap conductor to conductor, usually

(Internal Clearance) the direct distance between the

photoemitter and photodetector

inside the optocoupler cavity.

Minimum Internal NA NA 4.0 mm Measured from input terminals

Tracking (Internal to output terminals, along

Creepage) internal cavity.

Tracking Resistance CTI 200 200 200 Volts DIN IEC 112/VDE 0303 Part 1

(Comparative

Tracking Index)

Isolation Group IIIa IIIa IIIa Material Group

(DIN VDE 0110, 1/89, Table 1)

Option 300 - surface mount classification is Class A in accordance with CECC 00802.

IEC/EN/DIN EN 60747-5-2

Approved under:

IEC 60747-5-2:1997 + A1:2002

EN 60747-5-2:2001 + A1:2002

DIN EN 60747-5-2 (VDE 0884

Teil 2):2003-01

(Option 060 and HCNW only)

Recommended Pb-Free IR Profile

217 °C

RAMP-DOWN

6 °C/SEC. MAX.

RAMP-UP

3 °C/SEC. MAX.

150 - 200 °C

260 +0/-5 °C

t 25 °C to PEAK

60 to 150 SEC.

20-40 SEC.

TIME WITHIN 5 °C of ACTUAL

PEAK TEMPERATURE

t

p

t

s

PREHEAT

60 to 180 SEC.

t

L

T

L

T

smax

T

smin

25

T

p

TIME

TEMPERATURE

NOTES:

THE TIME FROM 25 °C to PEAK TEMPERATURE = 8 MINUTES MAX.

T

smax

= 200 °C, T

smin

= 150 °C

7

IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics

(HCPL-2211/2212 Option 060 ONLY)

Description Symbol Characteristic Units

Installation classification per DIN VDE 0110/1.89, Table 1

for rated mains voltage ≤300 V rms I-IV

for rated mains voltage ≤450 V rms I-III

Climatic Classification 55/85/21

Pollution Degree (DIN VDE 0110/1.89) 2

Maximum Working Insulation Voltage VIORM 630 V peak

Input to Output Test Voltage, Method b*

VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, VPR 1181 V peak

Partial Discharge < 5 pC

Input to Output Test Voltage, Method a*

VIORM x 1.5 = VPR, Type and sample test, VPR 945 V peak

tm = 60 sec, Partial Discharge < 5 pC

Highest Allowable Overvoltage*

(Transient Overvoltage, tini = 10 sec) VIOTM 6000 V peak

Safety Limiting Values

(Maximum values allowed in the event of a failure,

also see Figure 12, Thermal Derating curve.)

Case Temperature TS175 °C

Input Current IS,OUTPUT 230 mA

Output Power PS,OUTPUT 600 mW

Insulation Resistance at TS, VIO = 500 V RS≥109Ω

*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN

60747-5-2, for a detailed description.

Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in

application.

8

IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (HCNW22XX ONLY)

Description Symbol Characteristic Units

Installation classification per DIN VDE 0110/1.89, Table 1

for rated mains voltage ≤600 V rms I-IV

for rated mains voltage ≤1000 V rms I-III

Climatic Classification 55/100/21

Pollution Degree (DIN VDE 0110/1.89) 2

Maximum Working Insulation Voltage VIORM 1414 V peak

Input to Output Test Voltage, Method b*

VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, VPR 2652 V peak

Partial Discharge < 5 pC

Input to Output Test Voltage, Method a*

VIORM x 1.5 = VPR, Type and sample test, VPR 2121 V peak

tm = 60 sec, Partial Discharge < 5 pC

Highest Allowable Overvoltage*

(Transient Overvoltage, tini = 10 sec) VIOTM 8000 V peak

Safety Limiting Values

(Maximum values allowed in the event of a failure,

also see Figure 12, Thermal Derating curve.)

Case Temperature TS150 °C

Current (Input Current IF, PS = 0) IS,INPUT 400 mA

Output Power PS,OUTPUT 700 mW

Insulation Resistance at TS, VIO = 500 V RS≥109Ω

*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN

60747-5-2, for a detailed description.

Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in

application.

Absolute Maximum Ratings

Parameter Symbol Min. Max. Units Note

Storage Temperature TS-55 125 °C

Operating Temperature TA-40 85 °C

Average Forward Input Current IF(AVG) 10 mA 1

Peak Transient Input Current

(≤ 1 µs Pulse Width, 300 pps) IF(TRAN) 1.0 A 1

(≤ 200 µs Pulse Width, HCNW22XX 40 mA

< 1% Duty Cycle)

Reverse Input Voltage VR5V 1

HCNW22XX 3

Average Output Current IO25 mA 1

Supply Voltage V

CC 020V

Output Voltage VO-0.5 20 V 1

Total Package Power Dissipation PT210 mW 2

HCPL-223X 294

Output Power Dissipation POSee Figure 7 1

Lead Solder Temperature (Through Hole Parts 260°C for 10 sec.,

Only) 1.6 mm below seating plane

HCNW22XX 260°C for 10 sec., up to seating plane

Solder Reflow Temperature Profile (Surface See Package Outline Drawings section

Mount Parts Only)

9

Electrical Specifications

-40°C ≤ TA ≤ 85°C, 4.5 V ≤ V

CC ≤ 20 V, 1.6 mA ≤ IF(ON)* ≤ 5 mA, 0 V ≤ V

F(OFF) ≤ 0.8 V, unless otherwise

specified. All Typicals at TA = 25°C. See Note 7.

Parameter Sym. Min. Typ. Max. Units Test Conditions Fig. Note

Logic Low Output Voltage VOL 0.5 V IOL = 6.4 mA (4 TTL Loads) 1, 3 1

Logic High Output Voltage V

OH 2.4 ** V IOH = -2.6 mA 2, 3, 1

2.7 IOH = -0.4 mA

Output Leakage Current IOHH 100 µAV

O = 5.5 V IF = 5 mA 1

500 VO = 20 V

Logic Low Supply ICCL 3.7 6.0 mA VCC = 5.5 V VF = 0 V

4.3 7.0 VCC = 20 V

HCPL-223X 7.4 12.0 VCC = 5.5 V

8.6 14.0 VCC = 20 V

Logic High Supply ICCH 2.4 4.0 mA VCC = 5.5 V IF = 5 mA

2.7 5.0 VCC = 20 V

HCPL-223X 4.8 8.0 VCC = 5.5 V

5.4 10.0 VCC = 20 V

Logic Low Short Circuit IOSL 15 mA VO = VCC = 5.5 V VF = 0 V 1, 3

20 VO = VCC = 20 V

Logic High Short Circuit IOSH -10 mA VCC = 5.5 V IF = 5 mA 1, 3

-20 VCC = 20 V

Input Forward Voltage VF1.5 1.7 V TA = 25°CI

F = 5 mA 4 1

1.85

HCNW22XX 1.5 1.82 TA = 25°C

1.95

Input Reverse Breakdown BVR5VI

R = 10 µA1

HCNW22XX 3 IR = 100 µA

Input Diode Temperature ∆VF-1.7 mV/ °CIF = 5 mA

HCNW22XX ∆T

A-1.4

Input Capacitance CIN 60 pF f = 1 MHz, VF = 0 V 1, 4

HCNW22XX 70

*For HCPL-223X, 1.8 mA ≤ IF(ON) ≤ 5 mA.

**Typical VOH = VCC - 2.1 V.

Recommended Operating Conditions

Parameter Symbol Min. Max. Units

Power Supply Voltage VCC 4.5 20 V

Forward Input Current (ON) IF(ON) 1.6* 5 mA

HCPL-223X 1.8†

Forward Input Voltage (OFF) VF(OFF) - 0.8 V

Operating Temperature T

A-40 85 °C

Junction Temperature TJ-40 125 °C

Fan Out N 4 TTL Loads

*The initial switching threshold is 1.6 mA or less. It is recommended that 2.2 mA be used to permit at least a 20% LED degradation

guardband.

†The initial switching threshold is 1.8 mA or less. It is recommended that 2.5 mA be used to permit at least a 20% LED degradation

guardband.

8

(V

OUT > V

CC)

Current

Current

Output Current

Output Current V

O = GND

Voltage

Coefficient

IO = Open

IO = Open

10

Switching Specifications (AC)

-40°C ≤ T

A ≤ 85°C, 4.5 V ≤ VCC ≤ 20 V, 1.6 mA ≤ IF(ON)* ≤ 5 mA, 0 V ≤ VF(OFF) ≤ 0.8 V.

All Typicals at TA = 25°C, V

CC = 5 V, IF(ON) = 3 mA unless otherwise specified.

Parameter Sym. Min. Typ. Max. Units Test Conditions Fig. Note

Propagation Delay Time tPHL 150 ns Without Peaking Capacitor 5, 6 1, 6

160 HCNW22XX

150 300 With Peaking Capacitor

Propagation Delay Time tPLH 110 ns Without Peaking Capacitor 5, 6 1, 6

180 HCNW22XX

90 300 With Peaking Capacitor

Output Rise Time (10-90%) tr30 ns 5, 9 1

Output Fall Time (90-10%) tf7 ns 5, 9 1

Parameter Sym. Device Min. Units Test Conditions Fig. Note

Logic High |CMH| HCPL-2201/02 1,000 V/µs|V

CM| = 50 V VCC = 5 V 10 1, 7

Common Mode HCPL-0201 IF = 1.6 mA†TA = 25°C

Transient HCPL-2231

Immunity HCNW2201

HCPL-2211/12 5,000 V/µs|V

CM| = 300 V

HCPL-0211 IF = 1.6 mA‡

10,000 V/µs|V

CM| = 1 kV

IF = 5.0 mA

Logic Low |CML| HCPL-2201/02 1,000 V/µs|V

CM| = 50 V VF = 0 V 10 1, 7

Common Mode HCPL-0201 VCC = 5 V

Transient HCPL-2231 TA = 25°C

Immunity HCNW2201

HCPL-2211/12 10,000 V/µs|V

CM| = 1 kV

HCPL-0211

HCPL-2232

HCNW2211

*For HCPL-223X, 1.8 mA ≤ IF(ON) ≤ 5 mA.

†IF = 1.8 mA for HCPL-2231.

‡IF = 1.8 mA for HCPL-2232.

HCPL-2232

HCNW2211

to Logic Low

Output Level

to Logic High

Output Level

11

Package Characteristics

Parameter Sym. Min. Typ. Max. Units Test Conditions Fig. Note

Input-Output Momentary VISO 3750 V rms RH < 50%, t = 1 min. 5, 10

HCNW22XX 5000 T

A = 25°C

Input-Output Resistance RI-O 1012 ΩVI-O = 500 Vdc 5

HCNW22XX 1012 1013 T

A = 25°C

1011 T

A = 100°C

Input-Output Capacitance CI-O 0.6 pF f = 1 MHz, 5

HCNW22XX 0.5 0.6 T

A = 25°C

Input-Input Insulation II-I 0.005 µA Relative Humidity = 45%, 12

Leakage Current t = 5 s, VI-I = 500 V

Resistance (Input-Input) RI-I 1011 ΩVI-I = 500 V 12

Capacitance (Input-Input) CI-I 0.25 pF f = 1 MHz 12

*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output

continuous voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table

(if applicable), your equipment level safety specification or Agilent Application Note 1074 entitled “Optocoupler Input-Output

Endurance Voltage,” publication number 5963-2203E.

Withstand

Voltage*

VI-O = 0 Vdc

Notes:

1. Each channel.

2. Derate total package power dissipation, PT, linearly above 70°C free-air temperature at a rate of 4.5 mW/°C.

3. Duration of output short circuit time should not exceed 10 ms.

4. For single devices, input capacitance is measured between pin 2 and pin 3.

5. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together.

6. The tPLH propagation delay is measured from the 50% point on the leading edge of the input pulse to the 1.3 V point on the

leading edge of the output pulse. The tPHL propagation delay is measured from the 50% point on the trailing edge of the input

pulse to the 1.3 V point on the trailing edge of the output pulse.

7. CMH is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic high state,

VO > 2.0 V. CML is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic

low state, V

O < 0.8 V.

8. For HCPL-2202/12, V

O is on pin 6.

9. Use of a 0.1 µF bypass capacitor connected between pins 5 and 8 is recommended.

10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥4500 V rms for one second

(leakage detection current limit, II-O ≤5 µA). This test is performed before the 100% production test for partial discharge (Method

b) shown in the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table, if applicable.

11. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥6000 V rms for one second

(leakage detection current limit, II-O ≤5 µA). This test is performed before the 100% production test for partial discharge (Method

b) shown in the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table.

12. For HCPL-2231/32 only. Measured between pins 1 and 2, shorted together, and pins 3 and 4, shorted together.

5, 11

12

I

OH

– HIGH LEVEL OUTPUT CURRENT – mA

-60

-8

T

A

– TEMPERATURE – °C

100

0

-20

-5

20 60-40 0 40 80

-3

-1

-6

V

CC

= 4.5 V

I

F

= 5 mA

-7

-4

-2

V

O

= 2.7 V

V

O

= 2.4 V

VO – OUTPUT VOLTAGE – V

0

0

IF – INPUT CURRENT – mA

1.5

5

2

1.00.5

3

1

VCC = 4.5 V

TA = 25 °C

4

IO = 6.4 mA

IO = -2.6 mA

Figure 1. Typical Logic Low Output

Voltage vs. Temperature.

Figure 2. Typical Logic High Output

Current vs. Temperature.

Figure 3. Typical Output Voltage vs.

Forward Input Current.

IF – FORWARD CURRENT – mA

1.1

0.001

VF – FORWARD VOLTAGE – V

1.0

1000

1.3

0.01

1.51.2 1.4

0.1

TA = 25 °C

10

100

HCPL-22XX

HCPL-02XX

IF

+

–

VF

I

F

– FORWARD CURRENT – mA

1.1

0.001

V

F

– FORWARD VOLTAGE – V

1.0

1000

1.3

0.01

1.51.2 1.4

0.1

10

100

HCNW22XX

I

F

+

–

V

F

1.6

T

A

= 25 °C

Figure 4. Typical Input Diode Forward Characteristic.

Figure 5. Circuit for tPLH, tPHL, tr,t

f.

7

1

45

6

8

HCPL-2201/11

HCPL-02XX

HCNW22XX

GND

V

CC

5 V

619 Ω

INPUT

MONITORING

NODE

PULSE GEN.

t

r

= t

f =

5 ns

f = 100 kHz

10 % DUTY

CYCLE

V

O

= 5 V

Z

O

= 50

C

2

=

15 pF

THE PROBE AND JIG CAPACITANCES

ARE INCLUDED IN C

1 AND

C

2.

OUTPUT V

O

MONITORING

NODE

V

CC

R

1

D

1

D

2

5 kΩ

D

3

D

4

2

3

C

1

=

120 pF

R

1

I

F

(ON)

2.15 kΩ

1.6 mA

1.10 kΩ

3 mA

681 Ω

5 mA

ALL DIODES ARE 1N916 OR 1N3064.

*

7

45

6

8

HCPL-223X

GND

VCC

5 V

619 Ω

INPUT

MONITORING

NODE

PULSE GEN.

tr = tf = 5 ns

f = 100 kHz

10 % DUTY

CYCLE

VO = 5 V

ZO = 50

C2 =

15 pF

THE PROBE AND JIG CAPACITANCES

ARE INCLUDED IN C1 AND C2.

OUTPUT VO

MONITORING

NODE

VCC

R

1

D1

D2

5 kΩ

D3

D4

2

3

C1 =

120 pF

R

1

I

F

(ON)

1.96 kΩ

1.8 mA

1.10 kΩ

3 mA

681 Ω

5 mA

ALL DIODES ARE 1N916 OR 1N3064.

1

*

IF (ON)

50 % IF (ON)

0 mA

tPLH tPHL VOH

1.3 V

VOL

INPUT IF

OUTPUT VO

* 0.1 µF BYPASS — SEE NOTE 9.

VOL – LOW LEVEL OUTPUT VOLTAGE – V

-60

0

TA – TEMPERATURE – °C

100

1.0

-20

0.4

20 60-40 0 40 80

0.6

0.8

0.2

VCC = 4.5 V

VF = 0 V

IO = 6.4 mA

0.1

0.3

0.5

0.7

0.9

13

t

P

– PROPAGATION DELAY – ns

-60

50

T

A

– TEMPERATURE – °C

100

200

250

-20

100

20 60-40 0 40 80

150

HCNW22XX

V

CC

= 5.0 V, 20 V

C1 (120 pF) PEAKING CAPACITOR

IS USED. SEE FIGURE 5.

5

3

1.6

1.6,

5

I

F

(mA)

t

PHL

t

PLH

Figure 6. Typical Propagation Delays vs. Temperature. Figure 7. Maximum Output Power per

Channel vs. Supply Voltage.

V

OH

– HIGH LEVEL OUTPUT VOLTAGE – V

0

0

V

CC

– SUPPLY VOLTAGE – V

20

15

20

5

5

10 15

10

TYPICAL

V

OH

vs. V

CC

AT I

O

= -2.6 mA

T

A

= 25 °C

t

r

, t

f

– RISE, FALL TIME – ns

-60

0

T

A

– TEMPERATURE – °C

100

100

-20

40

20 60-40 0 40 80

60

80

20

t

r

V

CC

= 5 V

t

f

Figure 8. Typical Logic High Output

Voltage vs. Supply Voltage.

Figure 9. Typical Rise, Fall Time vs.

Temperature.

Figure 10. Test Circuit for Common Mode Transient Immunity and Typical Waveforms.

V

CM

(PEAK)

OUTPUT V

O

0 V

V

OH

|V

CM

|

V

OL

V

O

(MAX.)*

V

O

(MIN.)*

SWITCH AT A: I

F

= 1.6 mA**

SWITCH AT B: V

F

= 0 V

* SEE NOTE 7, 9.

** I

F

= 1.8 mA FOR HCPL-2231/32 DEVICES.

t

P

– PROPAGATION DELAY – ns

-60

50

T

A

– TEMPERATURE – °C

100

200

250

-20

100

20 60-40 0 40 80

150

I

F

(mA)

HCPL-22XX

HCPL-02XX

5

3

1.6*

1.6*

- 5

tPLH

tPHL

VCC = 5.0 V, 20 V

C1 (120 pF) PEAKING

CAPACITOR IS USED.

SEE FIGURE 5.

*IF = 1.8 mA FOR HCPL-223X

DEVICES.

P

O

– MAXIMUM OUTPUT POWER

PER CHANNEL (mW)

0

0

V

CC

– SUPPLY VOLTAGE – V

20

60

80

5

20

10

T

A

= 75 °C

15

40

T

A

= 85 °C

T

A

=

80°C

7

1

45

6

8

HCPL-2201/11

HCPL-02XX

HCNW22XX

0.1 µF

BYPASS

OUTPUT V

O

MONITORING

NODE

V

CC

RIN

2

3

VFF

A

B

–+

VCM

PULSE GENERATOR

–

+

7

45

6

8

HCPL-2231/32

0.1 µF

BYPASS

OUTPUT V

O

MONITORING

NODE

V

CC

2

3

V

FF

A

B

–+

V

CM

PULSE GENERATOR

1

+

–

R

1

14

OUTPUT POWER – P

S

, INPUT CURRENT – I

S

0

0

T

S

– CASE TEMPERATURE – °C

20050

400

12525 75 100 150

600

800

200

100

300

500

700

P

S

(mW)

I

S

(mA)

HCPL-2211/2212 OPTION 060

175

Figure 11. Typical Input Threshold Current vs. Temperature.

Figure 12. Thermal Derating Curve, Dependence of Safety Limiting Value with

Case Temperature per IEC/EN/DIN EN 60747-5-2.

Figure 13a. Recommended LSTTL to LSTTL Circuit where 500 ns Propagation

Delay is Sufficient.

18

27

36

45

1

2

HCPL-2201/11

HCPL-02XX

HCNW22XX

DATA INPUT

TTL OR LSTTL

VCC2 (+5 V)

UP TO 16 LSTTL LOADS

OR 4 TTL LOADS

*

* 0.1 µF BYPASS

1.1 kΩ

VCC1 (+5 V)

DATA OUTPUT

INPUT CURRENT THRESHOLD – mA

-60

0.5

TA – TEMPERATURE – °C

100

1.0

-20

0.7

20 60-40 0 40 80

0.8

0.9

0.6

VCC = 5.0 V

VCC = 20 V

HCPL-22XX

HCPL-02XX

IF (ON)

IF (OFF)

IF (ON)

IF (OFF)

INPUT CURRENT THRESHOLD – mA

-60

0.5

T

A

– TEMPERATURE – °C

100

1.0

-20

0.7

20 60-40 0 40 80

0.8

0.9

0.6

V

CC

= 5.0 V

V

CC

= 20 V

HCNW22XX

IF (ON)

IF (OFF)

IF (ON)

IF (OFF)

OUTPUT POWER P

S

, INPUT CURRENT I

S

0

0

T

S

– CASE TEMPERATURE – °C

175

1000

50

400

12525 75 100 150

600

800

200

100

300

500

700

900 P

S

(mW)

I

S

(mA)

HCNW22XX

15

Figure 16. Series LED Drive with Open Collector Gate

(4.7 k Resistor Shunts IOH from the LED).

Figure 14. LSTTL to CMOS Interface Circuit.

18

27

36

45

HCPL-2201/11

HCPL-02XX

HCNW22XX

DATA

INPUT

D1 (1N4150) REQUIRED FOR

ACTIVE PULL-UP DRIVER.

1.1 kΩ

V

CC1

(+5 V)

V

CC

GND

D1

TTL or

LSTTL

Figure 15. Alternative LED Drive

Circuit.

120 pF*

18

27

36

45

HCPL-2201/11

HCPL-02XX

HCNW22XX

DATA INPUT

TTL OR LSTTL

1.1 kΩ

80 Ω*

V

CC

(+5 V)

OPEN

COLLECTOR

GATE

* 120 pF PEAKING CAPACITOR

MAY BE OMITTED AND 80 Ω

RESISTOR MAY BE SHORTED

WHERE 500 ns PROPAGATION

DELAY IS SUFFICIENT.

V

CC

GND

4.7 kΩ

Figure 13b. Recommended LSTTL to LSTTL Circuit for Applications Requiring

a Maximum Allowable Propagation Delay of 300 ns.

120 pF

18

27

36

45

1

2

HCPL-2201/11

HCPL-02XX

HCNW22XX

DATA INPUT

TTL OR LSTTL

VCC2 (+5 V)

UP TO 16 LSTTL LOADS

OR 4 TTL LOADS

*

* 0.1 µF BYPASS

1.1 kΩ

80 Ω

VCC1 (+5 V)

DATA OUTPUT

120

pF* 18

27

36

45

12

HCPL-2201/11

HCPL-02XX

HCNW22XX

DATA

INPUT TTL OR LSTTL

V

CC2

(4.5 TO 20 V)

**0.1 µF BYPASS

1.1

kΩ

80 Ω*

V

CC1

(+5 V)

DATA

OUTPUT

TOTEM

POLE

OUTPUT

GATE * 120 pF PEAKING CAPACITOR

MAY BE OMITTED AND 80 Ω

RESISTOR MAY BE SHORTED

WHERE 500 ns PROPAGATION

DELAY IS SUFFICIENT.

V

CC

GND

CMOS

V

CC2

5 V

10 V

15 V

20 V

R

L

1.1 kΩ

2.37 kΩ

3.83 kΩ

5.11 kΩ

R

L

**

www.agilent.com/semiconductors

For product information and a complete list of

distributors, please go to our web site.

For technical assistance call:

Americas/Canada: +1 (800) 235-0312 or

(916) 788-6763

Europe: +49 (0) 6441 92460

China: 10800 650 0017

Hong Kong: (+65) 6756 2394

India, Australia, New Zealand: (+65) 6755 1939

Japan: (+81 3) 3335-8152 (Domestic/Interna-

tional), or 0120-61-1280 (Domestic Only)

Korea: (+65) 6755 1989

Singapore, Malaysia, Vietnam, Thailand,

Philippines, Indonesia: (+65) 6755 2044

Taiwan: (+65) 6755 1843

Data subject to change.

Copyright © 2005 Agilent Technologies, Inc.

Obsoletes 5989-0288EN

February 28, 2005

5989-2123EN