AP7365
Document number: DS32260 Rev. 10 - 2
1 of 18
www.diodes.com
October 2017
© Diodes Incorporated
AP7365
600mA, LOW QUIESCENT CURRENT
FAST TRANSIENT LOW DROPOUT LINEAR REGULATOR
Description
The AP7365 is a 600mA, adjustable and fixed output voltage, low
dropout linear regulator. This device includes pass element, error
amplifier, band-gap, current limit and thermal shutdown circuitry. The
device is turned on when EN pin is set to logic high level.
The characteristics of low dropout voltage and low quiescent current
make it suitable for low power applications such as battery powered
devices. The typical quiescent current is approximately 35μA. Built-in
current-limit and thermal-shutdown functions prevent IC from damage
in fault conditions.
This device is available with adjustable output from 0.8V to 5.0V, and
fixed version with 0.8V, 1.0V, 1.2V, 1.5V, 1.8V, 2.0V, 2.5V, 2.8V,
3.0V, 3.3V and 3.9V outputs. Please contact your local sales office for
other voltage options.
The AP7365 is available in SOT25, SOT89, SOT223, and U-
DFN2020-6 packages.
Features
600mA Low Dropout Regulator with EN
Very low IQ: 35µA
Wide Input Voltage Range: 2V to 6V
Wide Adjustable Output: 0.8V to 5.0V
Fixed Output Options: 0.8V to 3.9V (0.1V Step Size Possible)
High PSRR: 65dB at 1kHz
Fast Start-Up Time: 200µs
Stable with Low ESR, 1µF Ceramic Output Capacitor
Excellent Load/Line Transient Response
Low Dropout: 300mV at 600mA
Current Limit and Short Circuit Protection
Thermal Shutdown Protection
Ambient Temperature Range: -40°C to +85°C
Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2)
Halogen and Antimony Free. “Green” Device (Note 3)
Applications
Servers and Notebook Computers
Low and Medium Power Applications
FPGA and DSP Core or I/O Power
Consumer Electronics
Pin Assignments
SOT25 (Fixed Output)
IN
EN
OUT
(Top View)
5
3
2
1
GND
NC4
(W Package)
IN
EN ADJ
OUT
(Top View)
5
43
2
1
GND
SOT25 (ADJ Output)
(W Package)
NC
NC
OUT
GND
EN
IN
6
5
4
1
2
3
(Top View)
U-DFN2020-6 (Fixed Output)
(SN Package)
ADJ
NC
OUT
GND
EN
IN
6
5
4
1
2
3
(Top View)
U-DFN2020-6 (ADJ Output)
(SN Package)
IN
OUT
GND (TAB)
SOT89 (Fixed output)
(Top View)
3
2
1
(Y Package)
OUT
GND
IN (TAB)
SOT89 (Fixed output)
(Top View)
3
2
1
(YR Package)
IN
OUT
GND (TAB)
SOT223 (Fixed output)
(Top View)
3
2
1
(E Package)
OUT
GND
IN (TAB)
SOT223 (Fixed output)
(Top View)
3
2
1
(ER Package)
OUT (TAB)
GND
IN
SOT223 (Fixed output)
(Top View)
3
2
1
(EV Package)
Notes: 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant.
2. See http://www.diodes.com/quality/lead_free.html for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green"
and Lead-free.
3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and
<1000ppm antimony compounds.
AP7365
Document number: DS32260 Rev. 10 - 2
2 of 18
www.diodes.com
October 2017
© Diodes Incorporated
AP7365
Typical Applications Circuit
1μF
IN
GND
EN
OUT
Enable ADJ
R2
R1 1μF
VIN VOUT
AP7365
Adjustable Output
1μF
IN
GND
EN
OUT
Enable 1μF
VIN VOUT
AP7365
Fixed Output
K80Rwhere
R
R
1VV 2
2
1
REFOUT
Pin Descriptions
Pin
Name
Pin Number
Functions
SOT25
(Fixed)
SOT25
(ADJ)
U-DFN2020-6
(Fixed)
U-DFN2020-6
(ADJ)
SOT89
(Y Package)
SOT223
(E Package)
SOT89
(YR Package)
SOT223
(ER Package)
SOT223
(EV Package)
IN
1
1
3
3
3
2
3
Voltage Input Pin. Bypass to
ground through at least 1µF MLCC
capacitor
GND
2
2
2
2
2
1
1
Ground
EN
3
3
1
1
—
—
—
Enable Input, Active High
ADJ
—
4
—
6
—
—
—
Output Feedback Pin
NC
4
—
5, 6
5
—
—
—
No Connection
OUT
5
5
4
4
1
3
2
Voltage Output Pin. Bypass to
ground through 1µF MLCC
capacitor
Functional Block Diagram
IN
EN
GND
OUT
Gate
Driver
0.8V
Current Limit
and Thermal
Shutdown
Fixed Version
R
R
IN
EN
GND
ADJ
OUT
Gate
Driver
0.8V
Current Limit
and Thermal
Shutdown
Adjustable Version
AP7365
Document number: DS32260 Rev. 10 - 2
3 of 18
www.diodes.com
October 2017
© Diodes Incorporated
AP7365
Absolute Maximum Ratings (@TA = +25°C, unless otherwise specified.)
Symbol
Parameter
Ratings
Unit
ESD HBM
Human Body Model ESD Protection
2000
V
ESD MM
Machine Model ESD Protection
200
V
VIN
Input Voltage
6.5
V
OUT, EN Voltage
VIN +0.3
V
Continuous Load Current per Channel
Internal Limited
TST
Storage Temperature Range
-65 to +150
°C
TJ
Maximum Junction Temperature
+150
°C
Recommended Operating Conditions (@TA = +25°C, unless otherwise specified.)
Symbol
Parameter
Min
Max
Unit
VIN
Input Voltage
2
6
V
IOUT
Output Current (Note 4)
0
600
mA
TA
Operating Ambient Temperature
-40
+85
°C
Note: 4. The device maintains a stable, regulated output voltage without a load current.
Electrical Characteristics (@TA = +25°C, VIN = VOUT +1V, COUT = 1μF, CIN = 1μF, VEN = 2V, unless otherwise specified.)
Symbol
Parameter
Test Conditions
Min
Typ
Max
Unit
VREF
ADJ Reference Voltage (Adjustable Version)
IOUT = 0mA
—
0.8
—
V
IADJ
ADJ Leakage (Adjustable Version)
—
—
0.1
1.0
μA
VOUT
Output Voltage Accuracy
TA = -40°C to +85°C,
IOUT = 10% of IOUT-Max
-2
—
+2
%
VOUT
/VIN/V
Line Regulation
VIN = (VOUT +1V) to VIN-Max,
VEN = VIN, IOUT = 1mA
—
0.02
0.20
%/V
VOUT/VOUT
Load Regulation
VIN = (VOUT +1V) to VIN-Max,
IOUT = 1mA to 600mA
-1.0
—
+1.0
%
VDROPOUT
Dropout Voltage (Note 5)
VOUT < 2.5V, IOUT = 600mA
—
370
600
mV
VOUT ≥ 2.5V, IOUT = 600mA
—
300
400
IQ
Input Quiescent Current
VEN = VIN, IOUT = 0mA
—
35
80
μA
ISHDN
Input Shutdown Current
VEN = 0V, IOUT = 0mA
—
0.1
1.0
μA
ILEAK
Input Leakage Current
VEN = 0V, OUT grounded
—
0.1
1.0
μA
tST
Start-Up Time
VEN = 0V to 2.0V in 1μs,
IOUT = 600mA
—
200
—
μs
PSRR
PSRR (Note 6)
VIN = [VOUT +1V] VDC + 0.5VppAC,
f = 1kHz, IOUT = 50mA
—
65
—
dB
ISHORT
Short-Circuit Current
VIN = VIN-Min to VIN-Max,
VOUT < 0.2V (fixed version) or 25% of
VOUT (ADJ version)
—
240
—
mA
ILIMIT
Current limit
VIN = VIN-Min to VIN-Max,
VOUT/ROUT = 2.5A
0.8
1.4
—
A
VIL
EN Input Logic Low Voltage
VIN = VIN-Min to VIN-Max
—
—
0.4
V
VIH
EN Input Logic High Voltage
VIN = VIN-Min to VIN-Max
1.4
—
—
V
IEN
EN Input Current
VIN = 0V or VIN-Max
-1
—
+1
μA
TSHDN
Thermal Shutdown Threshold
—
—
+145
—
°C
THYS
Thermal Shutdown Hysteresis
—
—
+15
—
°C
Notes: 5. Dropout voltage is the voltage difference between the input and the output at which the output voltage drops 2% below its nominal value. This
parameter only applies to input voltages above minimum VIN = 2.0V.
6. At VIN < 2.3V, the PSRR performance may be reduced.
AP7365
Document number: DS32260 Rev. 10 - 2
4 of 18
www.diodes.com
October 2017
© Diodes Incorporated
AP7365
Electrical Characteristics (Cont.) (@TA = +25°C, VIN = VOUT +1V, COUT = 1μF, CIN = 1μF, VEN = 2V, unless otherwise specified.)
Symbol
Parameter
Test Conditions
Min
Typ
Max
Unit
JA
Thermal Resistance Junction-to-Ambient
SOT25 (Note 7)
—
169
—
°C /W
U-DFN2020-6 (Note 7)
—
132
—
SOT89 (Note 7)
—
133
—
SOT223 (Note 7)
—
142
—
JC
Thermal Resistance Junction-to-Case
SOT25 (Note 7)
—
31
—
°C /W
U-DFN2020-6 (Note 7)
—
48
—
SOT89 (Note 7)
—
30
—
SOT223 (Note 7)
—
39
—
Note: 7. Test condition for all packages: Device mounted on FR-4 substrate PC board, 1oz copper, with minimum recommended pad layout.
Typical Performance Characteristics
Time (40μs/div)
Start-Up Time
Time (40μs/div)
Start-Up Time
Time (40μs/div)
Line Transient Response
Time (40μs/div)
Line Transient Response
VOUT = 3.3V (1V/div)
with 600mA load
VEN = 0 to 2V (1V/div)
VIN = 5V
CIN = COUT = 1μF
VOUT = 3.3V (20mV/div)
IOUT = 60mA (200mA/div)
VIN = 4.3V to 5.3V (1V/div)
tR = tF = 2μs
CIN = none, COUT = 1μF
VOUT = 3.3V (20mV/div)
IOUT = 300mA (200mA/div)
VIN = 4.3V to 5.3V (1V/div)
tR = tF = 2μs
CIN = none, COUT = 1μF
VEN = 0 to 2V (1V/div)
VIN = 5V
CIN = COUT = 1μF
VOUT = 3.3V (1V/div)
with no load
AP7365
Document number: DS32260 Rev. 10 - 2
5 of 18
www.diodes.com
October 2017
© Diodes Incorporated
AP7365
Typical Performance Characteristics (Cont.)
Load Transient Response
Time (100μs/div)
Load Transient Response
Time (100μs/div)
Load Transient Response
Time (100μs/div)
Load Transient Response
Time (100μs/div)
VOUT = 1.8V (200mV/div)
VOUT = 1.8V (200mV/div)
VIN = VEN = 2.8V
CIN = COUT = 1μF
tR = tF = 1μs
VIN = VEN = 2.8V
CIN = COUT = 1μF
tR = tF = 1μs
IOUT = 10mA to 300mA (500mA/div)
IOUT = 10mA to 600mA (500mA/div)
VOUT = 3.3V (200mV/div)
VIN = VEN = 4.3V
CIN = COUT = 1μF
tR = tF = 1μs
IOUT = 10mA to 300mA (500mA/div)
VOUT = 3.3V (200mV/div)
VIN = VEN = 4.3V
CIN = COUT = 1μF
tR = tF = 1μs
IOUT = 10mA to 600mA (500mA/div)
AP7365
Document number: DS32260 Rev. 10 - 2
6 of 18
www.diodes.com
October 2017
© Diodes Incorporated
AP7365
Typical Performance Characteristics (Cont.)
0.1
1.0
10.0
100.0
FREQUENCY (kHz)
PSRR
80
70
60
50
40
30
20
0
10
P
S
R
R
(
d
B
)
I = 50mA
OUT
I =300mA
OUT
V = 2.25V +0.5V
V = 0.8V
C = none, C = 1µF
T = +25°C
IN ppAC
OUT
IN OUT
A
I = 50mA
OUT
I =300mA
OUT
0.1
1.0
10.0
100.0
FREQUENCY (kHz)
PSRR
80
V = 2.25V +0.5V
V = 1.2V
C = none, C = 1µF
T = +25°C
IN ppAC
OUT
IN OUT
A
70
60
50
40
30
20
0
10
P
S
R
R
(
d
B
)
4.0 4.5 5.5 6.05.0
INPUT VOLTAGE (V)
Input Quiescent Current vs. Input Voltage
60
50
40
20
10
0
30
INPUT QUIESCENT CURRENT (µA)
T = 25
癈
V = 3.3V
I = 0mA
A
OUT
OUT
-50 -25 75 12525
TEMPERATURE (
癈
)
Input Quiescent Current vs. Temperature
050 100
60
50
40
20
10
0
30
INPUT QUIESCENT CURRENT (µA)
V = 3.3V
I = 0mA
OUT
OUT
V = V = 4.3V
IN EN
PSRR (dB)
PSRR (dB)
I = 50mA
OUT
I = 300mA
OUT
0.1
1.0
10.0
100.0
FREQUENCY (kHz)
PSRR
80
70
60
50
40
30
20
10
P
S
R
R
(
d
B
)
0
V = 2.8V +0.5VppAC
V = 1.8V
C = none, C = 1µF
T = +25°C
IN
OUT
IN OUT
A
PSRR (dB)
V = 4.3V +0.5VppAC
V = 3.3V
C = none, C = 1µF
T = +25°C
IN
OUT
IN OUT
A
I = 50mA
OUT
I = 300mA
OUT
0.1
1.0
10.0
100.0
FREQUENCY (kHz)
PSRR
80
70
60
50
40
30
20
10
P
S
R
R
(
d
B
)
0
PSRR (dB)
TA = 25°C
VOUT = 3.3V
IOUT = 0mA
(°C )
AP7365
Document number: DS32260 Rev. 10 - 2
7 of 18
www.diodes.com
October 2017
© Diodes Incorporated
AP7365
Typical Performance Characteristics (Cont.)
-50 -25 0 75 100 12525 50
TEMPERATURE (
癈
)
Short Circuit Current vs. Temperature
500
400
100
0
200
SHORT CIRCUIT CURRENT (mA)
300
V = 4.3V
IN
ADJ Reference Voltage vs Temperature
0.78
0.79
0.80
0.81
0.82
-50 -25 0 25 50 75 100 125
Temperature(℃)
ADJ Reference Voltage(V)
0
100
600
300
OUTPUT CURRENT (mA)
Load Regulation
200
400
500
0.1
0.0
-0.1
-0.3
-0.4
-0.5
-0.2
O
U
T
P
U
T
V
A
R
I
A
T
I
O
N
(
%
)
V = V = 4.3V
IN EN
V = 3.3V
OUT
+25°C
+90°C
-45°C
OUTPUT VARIATION (%)
V = 3.3V
I = 1mA
OUT
OUT
4.0
4.5
5.5
6.0
5.0
INPUT VOLTAGE (V)
Line Regulation
0.08
-0.04
-0.08
0.00
O
U
T
P
U
T
V
A
R
I
A
T
I
O
N
(
%
)
0.04
+25°C
-45°C
+90°C
OUTPUT VARIATION (%)
0
100
600
300
OUTPUT CURRENT (mA)
Dropout Voltage vs. Output Current
200
400
500
600
100
0
300
D
R
O
P
O
U
T
V
O
L
T
A
G
E
(
m
V
)
500
400
200
+25°C
+90°C
-45°C
V = 1.8V
OUT
DROPOUT VOLTAGE (mV)
V = 3.3V
OUT
+25°C
+90°C
-45°C
0
100
600
300
OUTPUT CURRENT (mA)
Dropout Voltage vs. Output Current
200
400
500
100
0
300
D
R
O
P
O
U
T
V
O
L
T
A
G
E
(
m
V
)
500
400
200
DROPOUT VOLTAGE (mV)
(°C )
AP7365
Document number: DS32260 Rev. 10 - 2
8 of 18
www.diodes.com
October 2017
© Diodes Incorporated
AP7365
Typical Performance Characteristics (Cont.)
Application Information
Input Capacitor
A 1µF ceramic capacitor is recommended between IN and GND pins to decouple input power supply glitch and noise. The amount of the
capacitance may be increased without limit. This input capacitor must be located as close as possible to the device to assure input stability and
reduce noise. For PCB layout, a wide copper trace is required for both IN and GND pins. A lower ESR capacitor type allows the use of less
capacitance, while higher ESR type requires more capacitance.
Output Capacitor
The output capacitor is required to stabilize and improve the transient response of the LDO. The AP7365 is stable with very small ceramic output
capacitors. Using a ceramic capacitor value that is at least 1μF with ESR > 15mΩ on the output ensures stability. Higher capacitance values help
to improve line and load transient response. The output capacitance may be increased to keep low undershoot and overshoot. Output capacitor
must be placed as close as possible to OUT and GND pins.
3002001000 600500400
LOAD CURRENT (mA)
Region of Stable C ESR vs. Load Current
OUT
100
10
1
0.1
0.01
0.001
C ESR ( )
OUT
Unstable Range
Stable Range
V = 4.3V
C = C = 1
礔
IN
IN OUT
-50 -25 0 75 100 12525 50
TEMPERATURE (
癈
)
Current Limit vs. Temperature
2.0
1.6
0.4
0.0
0.8
CURRENT LIMIT (A)
1.2
V = 4.3V
V = 3.3V
IN
OUT
(°C )
VIN = 4.3V
CIN = COUT = 1µF
Unstable Range
Stable Range
Unstable Range
AP7365
Document number: DS32260 Rev. 10 - 2
9 of 18
www.diodes.com
October 2017
© Diodes Incorporated
AP7365
Application Information (Cont.)
Adjustable Operation
The AP7365 provides output voltage from 0.8V to 5.0V through external resistor divider as shown below.
1μF
IN
GND
EN
OUT
Enable ADJ
R2
R1 1μF
VIN VOUT
AP7365
The output voltage is calculated by:
2
R1
R
1
REF
V
OUT
V
Where VREF = 0.8V (the internal reference voltage)
Rearranging the equation will give the following that is used for adjusting the output to a particular voltage:
1
REF
VOUT
V
2
R
1
R
To maintain the stability of the internal reference voltage, R2 needs to be kept smaller than 80kΩ.
No Load Stability
Other than external resistor divider, no minimum load is required to keep the device stable. The device will remain stable and regulated in no load
condition.
ON/OFF Input Operation
The AP7365 is turned on by setting the EN pin high, and is turned off by pulling it low. If this feature is not used, the EN pin should be tied to IN pin
to keep the regulator output on at all time. To ensure proper operation, the signal source used to drive the EN pin must be able to swing above
and below the specified turn-on/off voltage thresholds listed in the Electrical Characteristics section under VIL and VIH.
Current Limit Protection
When output current at OUT pin is higher than current limit threshold, the current limit protection will be triggered and clamp the output current to
approximately 1.4A to prevent overcurrent and to protect the regulator from damage due to overheating.
Short Circuit Protection
When OUT pin is short-circuit to GND, short circuit protection will be triggered and clamp the output current to approximately 240mA. This feature
protects the regulator from overcurrent and damage due to overheating.
Thermal Shutdown Protection
Thermal protection disables the output when the junction temperature rises to approximately +145°C, allowing the device to cool down. When the
junction temperature reduces to approximately +130°C , the output circuitry is enabled again. Depending on power dissipation, thermal resistance
and ambient temperature, the thermal protection circuit may cycle on and off. This cycling limits the heat dissipation of the regulator, protecting it
from damage due to overheating.
Ultra Fast Start-Up
After enabled, the AP7365 is able to provide full power in as little as hundreds of microseconds, typically 200µs, without sacrificing low ground
current. This feature will help load circuitry move in and out of standby mode in real time, eventually extend battery life for mobile phones and
other portable devices.
AP7365
Document number: DS32260 Rev. 10 - 2
10 of 18
www.diodes.com
October 2017
© Diodes Incorporated
AP7365
Application Information (Cont.)
Fast Transient Response
Fast transient response LDO can extend battery life. TDMA-based cell phone protocols such as Global System for Mobile Communications (GSM)
have a transmit/receive duty factor of only 12.5%, enabling power savings by putting much of the baseband circuitry into standby mode in between
transmit cycles. In baseband circuits, the load often transitions virtually instantaneously from 100µA to 100mA. To meet this load requirement, the
LDO must react very quickly without a large voltage drop or overshoot — a requirement that cannot be met with conventional, general-purpose
LDO.
The AP7365’s fast transient response from 0 to 600mA provides stable voltage supply for fast DSP and GSM chipset with fast changing load.
Low Quiescent Current
The AP7365, consuming only around 35µA for all input ranges, provides great power saving in portable and low power applications.
Wide Output Range
The AP7365, with a wide output range of 0.8V to 5.0V, provides a versatile LDO solution for many portable applications.
Power Dissipation
The device power dissipation and proper sizing of the thermal plane connected to the thermal pad is critical to avoid thermal shutdown and ensure
reliable operation. Power dissipation of the device depends on input voltage and load conditions and can be calculated by:
PD = (VIN - VOUT) X IOUT
The maximum power dissipation, handled by the device, depends on the maximum junction to ambient thermal resistance, maximum ambient
temperature, and maximum device junction temperature, which can be calculated by the equation in the following:
JA
R)
A
T-C145(
)
TA
@MAX(
PD
Ordering Information
AP7365 - XX XX G - X
Packing
Package Green
G : Green 7/13 : Tape & Reel
Blank : ADJ (Note 8)
Output
10 : 1.0V
12 : 1.2V
15 : 1.5V
18 : 1.8V
25 : 2.5V
28 : 2.8V
30 : 3.0V
33 : 3.3V
20 : 2.0V
39 : 3.9V
08 : 0.8V W : SOT25
SN : U-DFN2020-6
Y/YR : SOT89
E/ER/EV : SOT223
Part Number
Package Code
Packaging
7”/13” Tape and Reel
Quantity
Part Number Suffix
AP7365-XXWG-7
W
SOT25
3,000/Tape & Reel
-7
AP7365-XXSNG-7
SN
U-DFN2020-6
3,000/Tape & Reel
-7
AP7365-XXYG-13
Y
SOT89
2,500/Tape & Reel
-13
AP7365-XXYRG-13
YR
SOT89
2,500/Tape & Reel
-13
AP7365-XXEG-13
E
SOT223
2,500/Tape & Reel
-13
AP7365-XXERG-13
ER
SOT223
2,500/Tape & Reel
-13
AP7365-XXEVG-13
EV
SOT223
2,500/Tape & Reel
-13
Note: 8. Adjustable version is only available in SOT25 and U-DFN2020-6 packages.
AP7365
Document number: DS32260 Rev. 10 - 2
11 of 18
www.diodes.com
October 2017
© Diodes Incorporated
AP7365
Marking Information
(1) SOT25
1 2 3
5
7
4
XX YW X
( Top View )
XX : Identification code
W : Week : A~Z : 1~26 week;
X : A~Z : Green
Y : Year 0~9
a~z : 27~52 week; z represents
52 and 53 week
Part Number
Package
Identification Code
AP7365-WG-7
SOT25
VA
AP7365-08WG-7
SOT25
VB
AP7365-10WG-7
SOT25
VC
AP7365-12WG-7
SOT25
VD
AP7365-15WG-7
SOT25
VE
AP7365-18WG-7
SOT25
VF
AP7365-20WG-7
SOT25
VG
AP7365-25WG-7
SOT25
VH
AP7365-28WG-7
SOT25
VJ
AP7365-30WG-7
SOT25
VK
AP7365-33WG-7
SOT25
VM
AP7365-39WG-7
SOT25
VN
(2) U-DFN2020-6
Y : Year : 0~9
( Top View )
Y WX
XX XX : Identification Code
X : A~Z : Green
W : Week : A~Z : 1~26 week;
a~z : 27~52 week; z represents
52 and 53 week
Part Number
Package
Identification Code
AP7365-SNG-7
U-DFN2020-6
VA
AP7365-08SNG-7
U-DFN2020-6
VB
AP7365-10SNG-7
U-DFN2020-6
VC
AP7365-12SNG-7
U-DFN2020-6
VD
AP7365-15SNG-7
U-DFN2020-6
VE
AP7365-18SNG-7
U-DFN2020-6
VF
AP7365-20SNG-7
U-DFN2020-6
VG
AP7365-25SNG-7
U-DFN2020-6
VH
AP7365-28SNG-7
U-DFN2020-6
VJ
AP7365-30SNG-7
U-DFN2020-6
VK
AP7365-33SNG-7
U-DFN2020-6
VM
AP7365-39SNG-7
U-DFN2020-6
VN
AP7365
Document number: DS32260 Rev. 10 - 2
12 of 18
www.diodes.com
October 2017
© Diodes Incorporated
AP7365
Marking Information (Cont.)
(3) SOT89
1 32
X X
Y W
XX : Identification code
( Top View )
X
Y : Year : 0~9
W : Week : A~Z : 1~26 week;
X : Internal code
A~Z : Green
a~z : 27~52 week;
z represents 52 and 53 week
Part Number
Package
Identification Code
AP7365-08YG-13
SOT89
VB
AP7365-10YG-13
SOT89
VC
AP7365-12YG-13
SOT89
VD
AP7365-15YG-13
SOT89
VE
AP7365-18YG-13
SOT89
VF
AP7365-20YG-13
SOT89
VG
AP7365-25YG-13
SOT89
VH
AP7365-28YG-13
SOT89
VJ
AP7365-30YG-13
SOT89
VK
AP7365-33YG-13
SOT89
VM
AP7365-39YG-13
SOT89
VN
AP7365-08YRG-13
SOT89
TB
AP7365-10YRG-13
SOT89
TC
AP7365-12YRG-13
SOT89
TD
AP7365-15YRG-13
SOT89
TE
AP7365-18YRG-13
SOT89
TF
AP7365-20YRG-13
SOT89
TG
AP7365-25YRG-13
SOT89
TH
AP7365-28YRG-13
SOT89
TJ
AP7365-30YRG-13
SOT89
TK
AP7365-33YRG-13
SOT89
TM
AP7365-39YRG-13
SOT89
TN
(4) SOT223 (E Package)
Y W X
6 5-VV
Logo
X : Internal code
( Top View )
A~Z : Green
Part Number
65-VV:08 for 0.8V
10 for 1.0V
12 for 1.2V
15 for 1.5V
18 for 1.8V
20 for 2.0V
25 for 2.5V
28 for 2.8V
30 for 3.0V
33 for 3.3V
39 for 3.9V
Y : Year : 0~9
W : Week : A~Z : 1~26 week;
a~z : 27~52 week;
z repersents 52 and 53 week
AP7365
Document number: DS32260 Rev. 10 - 2
13 of 18
www.diodes.com
October 2017
© Diodes Incorporated
AP7365
Marking Information (Cont.)
(5) SOT223 (ER Package)
Y W X
6 5 R -VV
Logo
X : Internal code
( Top View )
A~Z : Green
Part Number
65R-VV : 08 for 0.8V
10 for 1.0V
12 for 1.2V
15 for 1.5V
18 for 1.8V
20 for 2.0V
25 for 2.5V
28 for 2.8V
30 for 3.0V
33 for 3.3V
39 for 3.9V
Y : Year : 0~9
W : Week : A~Z : 1~26 week;
a~z : 27~52 week;
z repersents 52 and 53 week
(6) SOT223 (EV Package)
Y W X
6 5 V -VV
Logo
X : Internal code
( Top View )
A~Z : Green
Part Number
65V-VV : 08 for 0.8V
10 for 1.0V
12 for 1.2V
15 for 1.5V
18 for 1.8V
20 for 2.0V
25 for 2.5V
28 for 2.8V
30 for 3.0V
33 for 3.3V
39 for 3.9V
Y : Year : 0~9
W : Week : A~Z : 1~26 week;
a~z : 27~52 week;
z repersents 52 and 53 week
AP7365
Document number: DS32260 Rev. 10 - 2
14 of 18
www.diodes.com
October 2017
© Diodes Incorporated
AP7365
Package Outline Dimensions
Please see http://www.diodes.com/package-outlines.html for the latest version.
(1) Package Type: SOT25
(2) Package Type: U-DFN2020-6
SOT25
Dim
Min
Max
Typ
A
0.35
0.50
0.38
B
1.50
1.70
1.60
C
2.70
3.00
2.80
D
0.95
H
2.90
3.10
3.00
J
0.013
0.10
0.05
K
1.00
1.30
1.10
L
0.35
0.55
0.40
M
0.10
0.20
0.15
N
0.70
0.80
0.75
0°
8°
All Dimensions in mm
U-DFN2020-6
Dim
Min
Max
Typ
A
0.57
0.63
0.60
A1
0
0.05
0.03
A3
-
-
0.15
b
0.20
0.30
0.25
D
1.95
2.075
2.00
D2
1.45
1.65
1.55
e
-
-
0.65
E
1.95
2.075
2.00
E2
0.76
0.96
0.86
L
0.30
0.40
0.35
All Dimensions in mm
A
M
JL
D
B C
H
KN
D
D2
E
eb
L
E2
A
A1
A3
D2/2
E2/2
R0.100
Seating Plane
Pin #1 ID
AP7365
Document number: DS32260 Rev. 10 - 2
15 of 18
www.diodes.com
October 2017
© Diodes Incorporated
AP7365
Package Outline Dimensions (Cont.)
Please see http://www.diodes.com/package-outlines.html for the latest version.
(3) Package Type: SOT89
H1
EH
D1
B
e
c
L
A
D
8° (4X)
D2
E2
z
L1
R0.200
B1
(4) Package Type: SOT223
A1
A
7°
7°
D
b
e
e1
b1
C
E1
L
0° -10°
Q
E
0.25
Seating
Plane
Gauge
Plane
SOT89
Dim
Min
Max
Typ
A
1.40
1.60
1.50
B
0.50
0.62
0.56
B1
0.42
0.54
0.48
c
0.35
0.43
0.38
D
4.40
4.60
4.50
D1
1.62
1.83
1.733
D2
1.61
1.81
1.71
E
2.40
2.60
2.50
E2
2.05
2.35
2.20
e
-
-
1.50
H
3.95
4.25
4.10
H1
2.63
2.93
2.78
L
0.90
1.20
1.05
L1
0.327
0.527
0.427
z
0.20
0.40
0.30
All Dimensions in mm
SOT223
Dim
Min
Max
Typ
A
1.55
1.65
1.60
A1
0.010
0.15
0.05
b
0.60
0.80
0.70
b1
2.90
3.10
3.00
C
0.20
0.30
0.25
D
6.45
6.55
6.50
E
3.45
3.55
3.50
E1
6.90
7.10
7.00
e
-
-
4.60
e1
-
-
2.30
L
0.85
1.05
0.95
Q
0.84
0.94
0.89
All Dimensions in mm
AP7365
Document number: DS32260 Rev. 10 - 2
16 of 18
www.diodes.com
October 2017
© Diodes Incorporated
AP7365
Suggested Pad Layout
Please see http://www.diodes.com/package-outlines.html for the latest version.
(1) Package Type: SOT25
(2) Package Type: U-DFN2020-6
(3) Package Type: SOT89
Y4
X2
Y1
X
YY2
Y3
G
C
X1
Dimensions
Value (in mm)
Z
3.20
G
1.60
X
0.55
Y
0.80
C1
2.40
C2
0.95
Dimensions
Value
(in mm)
C
0.65
G
0.15
X
0.37
X1
1.67
Y
0.45
Y1
0.90
Dimensions
Value
(in mm)
C
1.500
G
0.244
X
0.580
X1
0.760
X2
1.933
Y
1.730
Y1
3.030
Y2
1.500
Y3
0.770
Y4
4.530
X
Z
Y
C1
C2C2
G
X1
YG
Y1
G
C
X
X
AP7365
Document number: DS32260 Rev. 10 - 2
17 of 18
www.diodes.com
October 2017
© Diodes Incorporated
AP7365
Suggested Pad Layout (Cont.)
Please see http://www.diodes.com/package-outlines.html for the latest version.
(4) Package Type: SOT223
X1
Y1
Y
XC
C1 Y2
Tape Orientation (Note 9)
For U-DFN2020-6
Note: 9. The taping orientation of the other package type can be found on our website at http://www.diodes.com/datasheets/ap02007.pdf.
Dimensions
Value (in mm)
C
2.30
C1
6.40
X
1.20
X1
3.30
Y
1.60
Y1
1.60
Y2
8.00
AP7365
Document number: DS32260 Rev. 10 - 2
18 of 18
www.diodes.com
October 2017
© Diodes Incorporated
AP7365
IMPORTANT NOTICE
DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
(AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).
Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes
without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the
application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or
trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume
all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated
website, harmless against all damages.
Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel.
Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and
hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or
indirectly, any claim of personal injury or death associated with such unintended or unauthorized application.
Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings
noted herein may also be covered by one or more United States, international or foreign trademarks.
This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the
final and determinative format released by Diodes Incorporated.
LIFE SUPPORT
Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express
written approval of the Chief Executive Officer of Diodes Incorporated. As used herein:
A. Life support devices or systems are devices or systems which:
1. are intended to implant into the body, or
2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the
labeling can be reasonably expected to result in significant injury to the user.
B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the
failure of the life support device or to affect its safety or effectiveness.
Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any
use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related
information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its
representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems.
Copyright © 2017, Diodes Incorporated
www.diodes.com
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Diodes Incorporated:
AP7365-08EG-13 AP7365-08ERG-13 AP7365-08SNG-7 AP7365-08WG-7 AP7365-08YG-13 AP7365-08YRG-13
AP7365-10EG-13 AP7365-10ERG-13 AP7365-10SNG-7 AP7365-10WG-7 AP7365-10YG-13 AP7365-10YRG-13
AP7365-12EG-13 AP7365-12ERG-13 AP7365-12SNG-7 AP7365-12WG-7 AP7365-12YG-13 AP7365-12YRG-13
AP7365-15EG-13 AP7365-15ERG-13 AP7365-15SNG-7 AP7365-15WG-7 AP7365-15YG-13 AP7365-15YRG-13
AP7365-18EG-13 AP7365-18ERG-13 AP7365-18SNG-7 AP7365-18WG-7 AP7365-18YG-13 AP7365-18YRG-13
AP7365-20EG-13 AP7365-20ERG-13 AP7365-20SNG-7 AP7365-20WG-7 AP7365-20YG-13 AP7365-20YRG-13
AP7365-25EG-13 AP7365-25ERG-13 AP7365-25SNG-7 AP7365-25WG-7 AP7365-25YG-13 AP7365-25YRG-13
AP7365-28EG-13 AP7365-28ERG-13 AP7365-28SNG-7 AP7365-28WG-7 AP7365-28YG-13 AP7365-28YRG-13
AP7365-30EG-13 AP7365-30ERG-13 AP7365-30SNG-7 AP7365-30WG-7 AP7365-30YG-13 AP7365-30YRG-13
AP7365-33EG-13 AP7365-33ERG-13 AP7365-33SNG-7 AP7365-33WG-7 AP7365-33YG-13 AP7365-33YRG-13
AP7365-39EG-13 AP7365-39ERG-13 AP7365-39SNG-7 AP7365-39WG-7 AP7365-39YG-13 AP7365-39YRG-13
AP7365-SNG-7 AP7365-WG-7
