LM13700 LM13700 Dual Operational Transconductance Amplifiers with Linearizing Diodes and Buffers Literature Number: SNOSBW2D LM13700 Dual Operational Transconductance Amplifiers with Linearizing Diodes and Buffers General Description Features The LM13700 series consists of two current controlled transconductance amplifiers, each with differential inputs and a push-pull output. The two amplifiers share common supplies but otherwise operate independently. Linearizing diodes are provided at the inputs to reduce distortion and allow higher input levels. The result is a 10 dB signal-tonoise improvement referenced to 0.5 percent THD. High impedance buffers are provided which are especially designed to complement the dynamic range of the amplifiers. The output buffers of the LM13700 differ from those of the LM13600 in that their input bias currents (and hence their output DC levels) are independent of IABC. This may result in performance superior to that of the LM13600 in audio applications. n n n n n n gm adjustable over 6 decades Excellent gm linearity Excellent matching between amplifiers Linearizing diodes High impedance buffers High output signal-to-noise ratio Applications n n n n n n n Current-controlled amplifiers Current-controlled impedances Current-controlled filters Current-controlled oscillators Multiplexers Timers Sample-and-hold circuits Connection Diagram Dual-In-Line and Small Outline Packages 00798102 Top View Order Number LM13700M, LM13700MX or LM13700N See NS Package Number M16A or N16A (c) 2004 National Semiconductor Corporation DS007981 www.national.com LM13700 Dual Operational Transconductance Amplifiers with Linearizing Diodes and Buffers June 2004 LM13700 Absolute Maximum Ratings (Note 1) Buffer Output Current (Note 3) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Operating Temperature Range LM13700N 0C to +70C DC Input Voltage Supply Voltage +VS to -VS Storage Temperature Range 36 VDC or 18V LM13700 -65C to +150C Soldering Information Power Dissipation (Note 2) TA = 25C LM13700N 20 mA Dual-In-Line Package 570 mW Soldering (10 sec.) 260C Differential Input Voltage 5V Diode Bias Current (ID) 2 mA Vapor Phase (60 sec.) 215C Amplifier Bias Current (IABC) 2 mA Infrared (15 sec.) 220C Output Short Circuit Duration Continuous Small Outline Package Electrical Characteristics (Note 4) Parameter Conditions LM13700 Units Typ Max Over Specified Temperature Range 0.4 4 IABC = 5 A 0.3 4 VOS Including Diodes Diode Bias Current (ID) = 500 A 0.5 5 mV Input Offset Change 5 A IABC 500 A 0.1 3 mV 0.1 0.6 A Over Specified Temperature Range 0.4 5 A Input Offset Voltage (VOS) Min Input Offset Current Input Bias Current Forward Transconductance (gm) 6700 Over Specified Temperature Range 8 13000 mho 5400 gm Tracking Peak Output Current 1 9600 mV 0.3 RL = 0, IABC = 5 A dB 5 RL = 0, IABC = 500 A 350 RL = 0, Over Specified Temp Range 300 RL = , 5 A IABC 500 A +12 +14.2 RL = , 5 A IABC 500 A -12 500 650 A Peak Output Voltage Positive Negative V -14.4 V IABC = 500 A, Both Channels 2.6 mA Positive VOS/V+ 20 150 V/V Negative VOS/V- 20 150 V/V Supply Current VOS Sensitivity CMRR Common Mode Range Crosstalk Referred to Input (Note 5) Differential Input Current IABC = 0, Input = 4V Leakage Current IABC = 0 (Refer to Test Circuit) 80 110 12 13.5 dB V 100 dB 20 Hz < f < 20 kHz Input Resistance 10 Open Loop Bandwidth 0.02 100 0.2 100 nA 26 k 2 MHz Slew Rate Unity Gain Compensated 50 Buffer Input Current (Note 5) 0.5 Peak Buffer Output Voltage (Note 5) 10 nA V/s 2 A V Note 1: "Absolute Maximum Ratings" indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Note 2: For operation at ambient temperatures above 25C, the device must be derated based on a 150C maximum junction temperature and a thermal resistance, junction to ambient, as follows: LM13700N, 90C/W; LM13700M, 110C/W. Note 3: Buffer output current should be limited so as to not exceed package dissipation. www.national.com 2 (Continued) Note 4: These specifications apply for VS = 15V, TA = 25C, amplifier bias current (IABC) = 500 A, pins 2 and 15 open unless otherwise specified. The inputs to the buffers are grounded and outputs are open. Note 5: These specifications apply for VS = 15V, IABC = 500 A, ROUT = 5 k connected from the buffer output to -VS and the input of the buffer is connected to the transconductance amplifier output. Schematic Diagram One Operational Transconductance Amplifier 00798101 Typical Application 00798118 Voltage Controlled Low-Pass Filter 3 www.national.com LM13700 Electrical Characteristics (Note 4) LM13700 Typical Performance Characteristics Input Offset Voltage Input Offset Current 00798139 00798138 Input Bias Current Peak Output Current 00798141 00798140 Peak Output Voltage and Common Mode Range Leakage Current 00798143 00798142 www.national.com 4 LM13700 Typical Performance Characteristics (Continued) Input Leakage Transconductance 00798144 00798145 Amplifier Bias Voltage vs. Amplifier Bias Current Input Resistance 00798146 00798147 Input and Output Capacitance Output Resistance 00798148 00798149 5 www.national.com LM13700 Typical Performance Characteristics (Continued) Distortion vs. Differential Input Voltage Voltage vs. Amplifier Bias Current 00798150 00798151 Output Noise vs. Frequency 00798152 Unity Gain Follower 00798105 www.national.com 6 LM13700 Typical Performance Characteristics (Continued) Leakage Current Test Circuit Differential Input Current Test Circuit 00798106 00798107 Circuit Description Linearizing Diodes The differential transistor pair Q4 and Q5 form a transconductance stage in that the ratio of their collector currents is defined by the differential input voltage according to the transfer function: For differential voltages greater than a few millivolts, Equation (3) becomes less valid and the transconductance becomes increasingly nonlinear. Figure 1 demonstrates how the internal diodes can linearize the transfer function of the amplifier. For convenience assume the diodes are biased with current sources and the input signal is in the form of current IS. Since the sum of I4 and I5 is IABC and the difference is IOUT, currents I4 and I5 can be written as follows: (1) where VIN is the differential input voltage, kT/q is approximately 26 mV at 25C and I5 and I4 are the collector currents of transistors Q5 and Q4 respectively. With the exception of Q12 and Q13, all transistors and diodes are identical in size. Transistors Q1 and Q2 with Diode D1 form a current mirror which forces the sum of currents I4 and I5 to equal IABC: (2) I4 + I5 = IABC where IABC is the amplifier bias current applied to the gain pin. For small differential input voltages the ratio of I4 and I5 approaches unity and the Taylor series of the In function can be approximated as: Since the diodes and the input transistors have identical geometries and are subject to similar voltages and temperatures, the following is true: (6) Notice that in deriving Equation (6) no approximations have been made and there are no temperature-dependent terms. The limitations are that the signal current not exceed ID/2 and that the diodes be biased with currents. In practice, replacing the current sources with resistors will generate insignificant errors. (3) (4) Collector currents I4 and I5 are not very useful by themselves and it is necessary to subtract one current from the other. The remaining transistors and diodes form three current mirrors that produce an output current equal to I5 minus I4 thus: Applications Voltage Controlled Amplifiers Figure 2 shows how the linearizing diodes can be used in a voltage-controlled amplifier. To understand the input biasing, it is best to consider the 13 k resistor as a current source and use a Thevenin equivalent circuit as shown in Figure 3. This circuit is similar to Figure 1 and operates the same. The potentiometer in Figure 2 is adjusted to minimize the effects of the control signal at the output. (5) The term in brackets is then the transconductance of the amplifier and is proportional to IABC. 7 www.national.com LM13700 Applications Voltage Controlled Amplifiers (Continued) 00798108 FIGURE 1. Linearizing Diodes Although the noise contribution of the linearizing diodes is negligible relative to the contribution of the amplifier's internal transistors, ID should be as large as possible. This minimizes the dynamic junction resistance of the diodes (re) and maximizes their linearizing action when balanced against RIN. A value of 1 mA is recommended for ID unless the specific application demands otherwise. For optimum signal-to-noise performance, IABC should be as large as possible as shown by the Output Voltage vs. Amplifier Bias Current graph. Larger amplitudes of input signal also improve the S/N ratio. The linearizing diodes help here by allowing larger input signals for the same output distortion as shown by the Distortion vs. Differential Input Voltage graph. S/N may be optimized by adjusting the magnitude of the input signal via RIN (Figure 2) until the output distortion is below some desired level. The output voltage swing can then be set at any level by selecting RL. 00798109 FIGURE 2. Voltage Controlled Amplifier www.national.com 8 LM13700 Applications Voltage Controlled Amplifiers (Continued) 00798110 FIGURE 3. Equivalent VCA Input Circuit If VC is derived from a second signal source then the circuit becomes an amplitude modulator or two-quadrant multiplier as shown in Figure 5, where: Stereo Volume Control The circuit of Figure 4 uses the excellent matching of the two LM13700 amplifiers to provide a Stereo Volume Control with a typical channel-to-channel gain tracking of 0.3 dB. RP is provided to minimize the output offset voltage and may be replaced with two 510 resistors in AC-coupled applications. For the component values given, amplifier gain is derived for Figure 2 as being: The constant term in the above equation may be cancelled by feeding IS x IDRC/2(V- + 1.4V) into IO. The circuit of Figure 6 adds RM to provide this current, resulting in a four-quadrant multiplier where RC is trimmed such that VO = 0V for VIN2 = 0V. RM also serves as the load resistor for IO. 9 www.national.com LM13700 Stereo Volume Control (Continued) 00798111 FIGURE 4. Stereo Volume Control 00798112 FIGURE 5. Amplitude Modulator www.national.com 10 LM13700 Stereo Volume Control (Continued) 00798113 FIGURE 6. Four-Quadrant Multiplier Noting that the gain of the LM13700 amplifier of Figure 3 may be controlled by varying the linearizing diode current ID as well as by varying IABC, Figure 7 shows an AGC Amplifier using this approach. As VO reaches a high enough amplitude (3VBE) to turn on the Darlington transistors and the linearizing diodes, the increase in ID reduces the amplifier gain so as to hold VO at that level. where gm 19.2IABC at 25C. Note that the attenuation of VO by R and RA is necessary to maintain VIN within the linear range of the LM13700 input. Figure 9 shows a similar VCR where the linearizing diodes are added, essentially improving the noise performance of the resistor. A floating VCR is shown in Figure 10, where each "end" of the "resistor" may be at any voltage within the output voltage range of the LM13700. Voltage Controlled Resistors An Operational Transconductance Amplifier (OTA) may be used to implement a Voltage Controlled Resistor as shown in Figure 8. A signal voltage applied at RX generates a VIN to the LM13700 which is then multiplied by the gm of the amplifier to produce an output current, thus: 00798114 FIGURE 7. AGC Amplifier 11 www.national.com LM13700 Voltage Controlled Resistors (Continued) 00798115 FIGURE 8. Voltage Controlled Resistor, Single-Ended 00798116 FIGURE 9. Voltage Controlled Resistor with Linearizing Diodes gm is again 19.2 x IABC at room temperature. Figure 12 shows a VC High-Pass Filter which operates in much the same manner, providing a single RC roll-off below the defined cut-off frequency. Additional amplifiers may be used to implement higher order filters as demonstrated by the two-pole Butterworth Lo-Pass Filter of Figure 13 and the state variable filter of Figure 14. Due to the excellent gm tracking of the two amplifiers, these filters perform well over several decades of frequency. Voltage Controlled Filters OTA's are extremely useful for implementing voltage controlled filters, with the LM13700 having the advantage that the required buffers are included on the I.C. The VC Lo-Pass Filter of Figure 11 performs as a unity-gain buffer amplifier at frequencies below cut-off, with the cut-off frequency being the point at which XC/gm equals the closed-loop gain of (R/RA). At frequencies above cut-off the circuit provides a single RC roll-off (6 dB per octave) of the input signal amplitude with a -3 dB point defined by the given equation, where www.national.com 12 LM13700 Voltage Controlled Filters (Continued) 00798117 FIGURE 10. Floating Voltage Controlled Resistor 00798118 FIGURE 11. Voltage Controlled Low-Pass Filter 13 www.national.com LM13700 Voltage Controlled Filters (Continued) 00798119 FIGURE 12. Voltage Controlled Hi-Pass Filter 00798120 FIGURE 13. Voltage Controlled 2-Pole Butterworth Lo-Pass Filter www.national.com 14 LM13700 Voltage Controlled Filters (Continued) 00798121 FIGURE 14. Voltage Controlled State Variable Filter increase amplifier A1's bias current and thus to increase the charging rate of capacitor C. When VO2 is low, IF goes to zero and the capacitor discharge current is set by IC. The VC Lo-Pass Filter of Figure 11 may be used to produce a high-quality sinusoidal VCO. The circuit of Figure 16 employs two LM13700 packages, with three of the amplifiers configured as lo-pass filters and the fourth as a limiter/ inverter. The circuit oscillates at the frequency at which the loop phase-shift is 360 or 180 for the inverter and 60 per filter stage. This VCO operates from 5 Hz to 50 kHz with less than 1% THD. Voltage Controlled Oscillators The classic Triangular/Square Wave VCO of Figure 15 is one of a variety of Voltage Controlled Oscillators which may be built utilizing the LM13700. With the component values shown, this oscillator provides signals from 200 kHz to below 2 Hz as IC is varied from 1 mA to 10 nA. The output amplitudes are set by IA x RA. Note that the peak differential input voltage must be less than 5V to prevent zenering the inputs. A few modifications to this circuit produce the ramp/pulse VCO of Figure 16. When VO2 is high, IF is added to IC to 15 www.national.com LM13700 Voltage Controlled Oscillators (Continued) 00798122 FIGURE 15. Triangular/Square-Wave VCO 00798123 FIGURE 16. Ramp/Pulse VCO www.national.com 16 LM13700 Voltage Controlled Oscillators (Continued) 00798124 FIGURE 17. Sinusoidal VCO Additional Applications Figure 19 presents an interesting one-shot which draws no power supply current until it is triggered. A positive-going trigger pulse of at least 2V amplitude turns on the amplifier through RB and pulls the non-inverting input high. The amplifier regenerates and latches its output high until capacitor C charges to the voltage level on the non-inverting input. The output then switches low, turning off the amplifier and discharging the capacitor. The capacitor discharge rate is speeded up by shorting the diode bias pin to the inverting input so that an additional discharge current flows through DI when the amplifier output switches low. A special feature of this timer is that the other amplifier, when biased from VO, can perform another function and draw zero stand-by power as well. 00798125 Figure 18 shows how to build a VCO using one amplifier when the other amplifier is needed for another function. FIGURE 18. Single Amplifier VCO 17 www.national.com LM13700 Additional Applications (Continued) 00798126 FIGURE 19. Zero Stand-By Power Timer The Phase-Locked Loop of Figure 21 uses the four-quadrant multiplier of Figure 6 and the VCO of Figure 18 to produce a PLL with a 5% hold-in range and an input sensitivity of about 300 mV. The operation of the multiplexer of Figure 20 is very straightforward. When A1 is turned on it holds VO equal to VIN1 and when A2 is supplied with bias current then it controls VO. CC and RC serve to stabilize the unity-gain configuration of amplifiers A1 and A2. The maximum clock rate is limited to about 200 kHz by the LM13700 slew rate into 150 pF when the (VIN1-VIN2) differential is at its maximum allowable value of 5V. 00798127 FIGURE 20. Multiplexer www.national.com 18 LM13700 Additional Applications (Continued) 00798128 FIGURE 21. Phase Lock Loop The Schmitt Trigger of Figure 22 uses the amplifier output current into R to set the hysteresis of the comparator; thus VH = 2 x R x IB. Varying IB will produce a Schmitt Trigger with variable hysteresis. 00798129 FIGURE 22. Schmitt Trigger The Peak Detector of Figure 24 uses A2 to turn on A1 whenever VIN becomes more positive than VO. A1 then charges storage capacitor C to hold VO equal to VIN PK. Pulling the output of A2 low through D1 serves to turn off A1 so that VO remains constant. Figure 23 shows a Tachometer or Frequency-to-Voltage converter. Whenever A1 is toggled by a positive-going input, an amount of charge equal to (VH-VL) Ct is sourced into Cf and Rt. This once per cycle charge is then balanced by the current of VO/Rt. The maximum FIN is limited by the amount of time required to charge Ct from VL to VH with a current of IB, where VL and VH represent the maximum low and maximum high output voltage swing of the LM13700. D1 is added to provide a discharge path for Ct when A1 switches low. 19 www.national.com LM13700 Additional Applications (Continued) 00798130 FIGURE 23. Tachometer 00798131 FIGURE 24. Peak Detector and Hold Circuit The Ramp-and-Hold of Figure 26 sources IB into capacitor C whenever the input to A1 is brought high, giving a ramp-rate of about 1V/ms for the component values shown. The true-RMS converter of Figure 27 is essentially an automatic gain control amplifier which adjusts its gain such that the AC power at the output of amplifier A1 is constant. The output power of amplifier A1 is monitored by squaring amplifier A2 and the average compared to a reference voltage with amplifier A3. The output of A3 provides bias current to www.national.com the diodes of A1 to attenuate the input signal. Because the output power of A1 is held constant, the RMS value is constant and the attenuation is directly proportional to the RMS value of the input voltage. The attenuation is also proportional to the diode bias current. Amplifier A4 adjusts the ratio of currents through the diodes to be equal and therefore the voltage at the output of A4 is proportional to the RMS value of the input voltage. The calibration potentiometer is set such that VO reads directly in RMS volts. 20 LM13700 Additional Applications (Continued) 00798132 FIGURE 25. Sample-Hold Circuit 00798133 FIGURE 26. Ramp and Hold 21 www.national.com LM13700 Additional Applications (Continued) 00798134 FIGURE 27. True RMS Converter The voltage on the base of Q1 is then The circuit of Figure 28 is a voltage reference of variable Temperature Coefficient. The 100 k potentiometer adjusts the output voltage which has a positive TC above 1.2V, zero TC at about 1.2V, and negative TC below 1.2V. This is accomplished by balancing the TC of the A2 transfer function against the complementary TC of D1. The wide dynamic range of the LM13700 allows easy control of the output pulse width in the Pulse Width Modulator of Figure 29. For generating IABC over a range of 4 to 6 decades of current, the system of Figure 30 provides a logarithmic current out for a linear voltage in. Since the closed-loop configuration ensures that the input to A2 is held equal to 0V, the output current of A1 is equal to I3 = -VC/RC. The differential voltage between Q1 and Q2 is attenuated by the R1,R2 network so that A1 may be assumed to be operating within its linear range. From Equation (5), the input voltage to A1 is: www.national.com The ratio of the Q1 and Q2 collector currents is defined by: Combining and solving for IABC yields: This logarithmic current can be used to bias the circuit of Figure 4 to provide temperature independent stereo attenuation characteristic. 22 LM13700 Additional Applications (Continued) 00798135 FIGURE 28. Delta VBE Reference 00798136 FIGURE 29. Pulse Width Modulator 23 www.national.com LM13700 Additional Applications (Continued) 00798137 FIGURE 30. Logarithmic Current Source www.national.com 24 LM13700 Physical Dimensions inches (millimeters) unless otherwise noted S.O. Package (M) Order Number LM13700M or LM13700MX NS Package Number M16A Molded Dual-In-Line Package (N) Order Number LM13700N NS Package Number N16A 25 www.national.com LM13700 Dual Operational Transconductance Amplifiers with Linearizing Diodes and Buffers Notes LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated