CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CG Chip Type, Higher Capacitance series Higher Capacitance, Low ESR, High ripple current. Load life of 2000 hours at 105C. SMD type : Lead free reflow soldering condition at 260C peak correspondence. Compliant to the RoHS directive (2002/95/EC). CG Higher Capacitance CF Specifications Item Performance Characteristics Category Temperature Range - 55 to +105C Rated Voltage Range 2.5 to 16V Rated Capacitance Range 47 to 3300F Capacitance Tolerance 20% at 120Hz, 20C Tangent of loss angle (tan ) Less than or equal to the specified value at 120Hz, 20C ESR ( Less than or equal to the specified value at 100kHz, 20C 1) Leakage Current ( 2) Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20C Temperature Characteristics (Max.Impedance Ratio) Z+105C / Z+20C Z- 55C / Z+20C Endurance The specifications listed at right shall be met when the capacitors are restored to 20C after the rated voltage is applied for 2000 hours at 105C. Capacitance change tan ESR ( 1) Leakage current ( 2) Within 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Damp Heat (Steady State) The specifications listed at right shall be met when the capacitors are restored to 20C after the rated voltage is applied for 1000 hours at 60C, 90% RH. Capacitance change tan ESR ( 1) Leakage current ( 2) Within 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan ESR ( 1) Leakage current ( 2) Within 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value 1.25 1.25 (100kHz) After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right, provided that it's temperature profile is measured at the capacitor top and the terminal. Pre-heating shall be done at 150 to 200C and for 60 to 180 sec. The duration for over +230C temperature at capacitor surface shall not exceed 60 seconds. In the case of peak temp, less than 250C, reflow soldering shall be two times maximum. In the case of peak temp, less than 260C, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Navy blue print on the case top Resistance to Soldering Heat Marking 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105C. 3 Initial value : The value before test of examination of resistance to soldering. Type numbering system (Example : 6.3V 470F) Dimensions Series 1 0.5 MAX. E B 0.2 D + 0.5 MAX. Voltage ( j:6.3v) C0.2 2 3 4 5 6 7 8 9 10 11 12 13 14 PCG 0 J 4 7 1 MC L 1 GS Taping code A0.2 Plastic platform 0.3 MAX. Lot No. CG 470 j 841 Capacitance Positive Configuration Capacitance toleranc (20%) L +0.1 - 0.4 Rated capacitance (470F) Negative Rated voltage (6.3V) H Series name (mm) Size D L A B C E H 5 x 6L 6.3 x 6L 8 x 7L 10 x 8L 10 x 10L 10 x 12.7L 5.0 6.3 10.0 10.0 8.0 10.0 5.9 5.9 7.9 9.9 6.9 12.6 6.0 7.3 11.0 11.0 9.0 11.0 5.3 6.6 10.3 10.3 8.3 10.3 5.3 6.6 10.3 10.3 8.3 10.3 1.6 2.1 4.6 4.6 3.2 4.6 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 Dimension table in next page. Type Voltage V 2.5 4 6.3 10 16 Code e g j A C CAT.8100Y CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CG series Standard Ratings Rated Voltage (V)(code) 2.5 (0E) 4 (0G) 6.3 (0J) 10 (1A) Surge Voltage (V) 2.8 4.6 7.2 11.5 Rated Capacitance (F) Case Size D x L (mm) tan Leakage Current (A) ESR (m) (at 100kHz 20C) Rated Ripple (mArms) Part Number 220 5x6 0.12 110 30 2100 PCG0E221MCL1GS 470 6.3 x 6 0.12 235 20 2900 PCG0E471MCL1GS 560 6.3 x 6 0.12 280 20 3000 PCG0E561MCL1GS 820 8x7 0.12 410 20 3300 PCG0E821MCL1GS 1500 10 x 8 0.12 750 17 4100 PCG0E152MCL1GS 2700 10 x 10 0.12 1350 12 4700 PCG0E272MCL1GS 3300 10 x 12.7 0.12 1650 10 5500 PCG0E332MCL1GS 180 5x6 0.12 144 32 1900 PCG0G181MCL1GS 390 6.3 x 6 0.12 312 22 2700 PCG0G391MCL1GS 680 8x7 0.12 544 21 3200 PCG0G681MCL1GS 1200 10 x 8 0.12 960 17 4000 PCG0G122MCL1GS 2200 10 x 10 0.12 1760 13 4600 PCG0G222MCL1GS 2700 10 x 12.7 0.12 2160 11 5300 PCG0G272MCL1GS 150 5x6 0.12 189 33 1800 PCG0J151MCL1GS 270 6.3 x 6 0.12 340 23 2600 PCG0J271MCL1GS 330 6.3 x 6 0.12 416 23 2700 PCG0J331MCL1GS 470 8x7 0.12 592 22 3100 PCG0J471MCL1GS 1000 10 x 8 0.12 1260 18 3800 PCG0J102MCL1GS 1800 10 x 10 0.12 2268 14 4400 PCG0J182MCL1GS 2200 10 x 12.7 0.12 2772 12 5000 PCG0J222MCL1GS 82 5x6 0.12 164 35 1700 PCG1A820MCL1GS 150 6.3 x 6 0.12 300 25 2500 PCG1A151MCL1GS 330 8x7 0.12 660 23 3100 PCG1A331MCL1GS 560 10 x 8 0.12 1120 20 3600 PCG1A561MCL1GS 820 10 x 10 0.12 1640 15 4300 PCG1A821MCL1GS 10 x 12.7 1000 16 (1C) 18.4 0.12 2000 13 4800 PCG1A102MCL1GS 47 5x6 0.12 150 40 1500 PCG1C470MCL1GS 82 6.3 x 6 0.12 262 30 2300 PCG1C820MCL1GS 150 8x7 0.12 480 28 2800 PCG1C151MCL1GS 270 10 x 8 0.12 864 25 3300 PCG1C271MCL1GS 470 10 x 10 0.12 1504 20 3700 PCG1C471MCL1GS 680 10 x 12.7 0.12 2176 18 4100 PCG1C681MCL1GS Rated ripple current (mArms) at 105C 100kHz Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100Y