Nonvolatile Memory,
1024-Position Digital Potentiometer
Data Sheet
AD5231
Rev. D
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©20012013 Analog Devices, Inc. All rights reserved.
Technical Support www.analog.com
FEATURES
1024-position resolution
Nonvolatile memory maintains wiper setting
Power-on refresh with EEMEM setting
EEMEM restore time: 140 µs typ
Full monotonic operation
10 kΩ, 50 kΩ, and 100 kΩ terminal resistance
Permanent memory write protection
Wiper setting readback
Predefined linear increment/decrement instructions
Predefined ±6 dB/step log taper increment/decrement
instructions
SPI®-compatible serial interface
3 V to 5 V single-supply or ±2.5 V dual-supply operation
28 bytes extra nonvolatile memory for user-defined data
100-year typical data retention, TA = 55°C
APPLICATIONS
Mechanical potentiometer replacement
Instrumentation: gain, offset adjustment
Programmable voltage to current conversion
Programmable filters, delays, time constants
Programmable power supply
Low resolution DAC replacement
Sensor calibration
FUNCTIONAL BLOCK DIAGRAM
EEMEM(0)
EEMEM(1)
AD5231
RDAC
CLK
SDI
GND
SDO
RDY
SDO
V
DD
V
SS
A
W
B
O1
O2
SDI
2
PR
WP
CS
ADDR
DECODE RDAC
REGISTER
DIGITAL
REGISTER
SERIAL
INTERFACE
EEMEM
CONTROL
28 BYT E S
USER EEMEM
DIGITAL
OUTOUT
BUFFER
02739-001
Figure 1.
CODE ( Decimal)
100
75
001023256
R
WA
(D), R
WB
(D); ( % of No min al R
AB
)
512 768
50
25
R
WB
R
WA
02739-002
Figure 2. RWA (D) and RWB (D) vs. Decimal Code
GENERAL DESCRIPTION
The AD5231 is a nonvolatile memory1, digitally controlled
potentiometer2 with 1024-step resolution. The device performs
the same electronic adjustment function as a mechanical
potentiometer with enhanced resolution, solid state reliability,
and remote controllability. The AD5231 has versatile programming
that uses a standard 3-wire serial interface for 16 modes of
operation and adjustment, including scratchpad programming,
memory storing and restoring, increment/decrement, ±6 dB/step
log taper adjustment, wiper setting readback, and extra EEMEM
for user-defined information, such as memory data for other
components, look-up table, or system identification information.
In scratchpad programming mode, a specific setting can be
programmed directly to the RDAC register that sets the
resistance between Terminals WA and Terminals WB. This
setting can be stored into the EEMEM and is transferred
automatically to the RDAC register during system power-on.
The EEMEM content can be restored dynamically or through
external PR strobing, and a WP function protects EEMEM
contents. To simplify the programming, the linear-step increment
or decrement commands can be used to move the RDAC wiper
up or down, one step at a time. The ±6 dB step commands can
be used to double or half the RDAC wiper setting.
The AD5231 is available in a 16-lead TSSOP. The part is
guaranteed to operate over the extended industrial temperature
range of −40°C to +85°C.
1 The terms nonvolatile memory and EEMEM are used interchangeably.
2 The terms digital potentiometer and RDAC are used interchangeably.
AD5231 Data Sheet
Rev. D | Page 2 of 28
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications ....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description ......................................................................... 1
Revision History ............................................................................... 2
Specifications ..................................................................................... 3
Electrical Characteristics10 kΩ, 50 kΩ, 100 kΩ Versions .. 3
Timing Characteristics10 kΩ, 50 kΩ, 100 kΩ Versions ...... 5
Absolute Maximum Ratings ............................................................ 7
ESD Caution .................................................................................. 7
Pin Configuration and Function Descriptions ............................. 8
Typical Performance Characteristics ............................................. 9
Test Circuits ..................................................................................... 13
Theory of Operation ...................................................................... 14
Scratchpad and EEMEM Programming .................................. 14
Basic Operation .......................................................................... 14
EEMEM Protection .................................................................... 14
Digital Input/Output Configuration ........................................ 15
Serial Data Interface ................................................................... 15
Daisy-Chain Operation ............................................................. 15
Terminal Voltage Operation Range ......................................... 16
Power-Up Sequence ................................................................... 16
Latched Digital Outputs ............................................................ 16
Advanced Control Modes ......................................................... 18
RDAC Structure.......................................................................... 19
Programming the Variable Resistor ......................................... 19
Programming the Potentiometer Divider ............................... 20
Programming Examples ............................................................ 21
Flash/EEMEM Reliability .......................................................... 22
Applications ..................................................................................... 23
Bipolar Operation from Dual Supplies.................................... 23
High Voltage Operation ............................................................ 23
Bipolar Programmable Gain Amplifier ................................... 23
10-Bit Bipolar DAC .................................................................... 23
10-Bit Unipolar DAC ................................................................. 24
Programmable Voltage Source with Boosted Output ........... 24
Programmable Current Source ................................................ 24
Programmable Bidirectional Current Source ......................... 25
Resistance Scaling ...................................................................... 25
RDAC Circuit Simulation Model ............................................. 26
Outline Dimensions ....................................................................... 27
Ordering Guide .......................................................................... 27
REVISION HISTORY
3/13Rev. C to Rev. D
Added tWP; Table 2 ............................................................................ 5
Changes to Ordering Guide .......................................................... 27
1/07—Rev. B to Rev. C
Updated Format .................................................................. Universal
Changes to Dynamic Characteristics Specifications ..................... 4
Changes to Table 2 Footnote ............................................................ 5
Changes to Table 3 ............................................................................. 7
Changes to Ordering Guide ........................................................... 27
9/04Rev. A to Rev. B
Updated Format .................................................................. Universal
Changes to Table 20 ......................................................................... 23
Changes to Resistance Scaling Section ......................................... 25
Changes to Ordering Guide ........................................................... 27
5/04Rev. 0 to Rev. A
Updated formatting ............................................................ Universal
Edits to Features, General Description, and Block Diagram ....... 1
Changes to Specifications ................................................................. 3
Replaced Timing Diagrams.............................................................. 6
Changes to Pin Function Descriptions ........................................... 8
Changes to Typical Performance Characteristics.......................... 9
Changes to Test Circuits ................................................................. 13
Edits to Theory of Operation ......................................................... 14
Edits to Applications ....................................................................... 23
Updated Outline Dimensions ........................................................ 27
12/01Revision 0: Initial Version
Data Sheet AD5231
Rev. D | Page 3 of 28
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS10 kΩ, 50 k, 100 kΩ VERSIONS
VDD = 3 V ± 10% or 5 V ± 10%, VSS = 0 V, V A = VDD, VB = 0 V, −40°C < TA < +85°C, unless otherwise noted.
Table 1.
Parameter Symbol Conditions Min Typ 1 Max Unit
DC CHARACTERISTICS
RHEOSTAT MODE
Resistor Differential Nonlinearity2 R-DNL RWB, VA = NC, monotonic −1 ±1/2 +1.8 LSB
Resistor Integral Nonlinearity2 R-INL RWB,VA = NC −0.2 +0.2 LSB
Nominal Resistor Tolerance ΔRAB/RAB D = 0x3FF −40 +20 %
Resistance Temperature Coefficient (ΔRWB/RWB)/ΔT × 106 600 ppm/°C
Wiper Resistance RW IW = 100 µA, VDD = 5.5 V,
code = half scale
15 100
W
DD
code = half scale
50
DC CHARACTERISTICS
POTENTIOMETER DIVIDER MODE
Resolution N 10 Bits
Differential Nonlinearity3 DNL Monotonic, TA = 25°C −1 ±1/2 +1 LSB
Monotonic, TA = −40°C or +85°C −1 +1.25 LSB
Integral Nonlinearity3 INL −0.4 +0.4 LSB
Voltage Divider Temperature
Coefficient
(ΔVW/VW)/ΔT × 106 Code = half scale 15 ppm/°C
Full-Scale Error VWFSE Code = full scale −3 0 % FS
Zero-Scale Error VWZSE Code = zero scale 0 1.5 % FS
RESISTOR TERMINALS
Terminal Voltage Range4 VA, B, W VSS VDD V
Capacitance A, B5 CA, B f = 1 MHz, measured to GND,
code = half-scale
50 pF
Capacitance W5 CW f = 1 MHz, measured to GND,
code = half-scale
50 pF
Common-Mode Leakage Current5, 6 ICM VW = VDD/2 0.01 1 µA
DIGITAL INPUTS AND OUTPUTS
Input Logic High VIH With respect to GND, VDD = 5 V 2.4 V
Input Logic Low VIL With respect to GND, VDD = 5 V 0.8 V
Input Logic High VIH With respect to GND, VDD = 3 V 2.1 V
Input Logic Low VIL With respect to GND, VDD = 3 V 0.6 V
Input Logic High VIH With respect to GND, VDD = +2.5 V,
VSS = −2.5 V
2.0 V
Input Logic Low VIL With respect to GND, VDD = +2.5 V,
VSS = −2.5 V
0.5 V
Output Logic High (SDO, RDY) VOH RPULL-UP = 2.2 kΩ to 5 V
(see Figure 26)
4.9 V
Output Logic Low VOL IOL = 1.6 mA, VLOGIC = 5 V
(see Figure 26)
0.4 V
Input Current IIL VIN = 0 V or VDD ±2.5 µA
Input Capacitance5 CIL 4 pF
Output Current5 IO1, IO2 VDD = 5 V, VSS = 0 V, TA = 25°C 50 mA
VDD = 2.5 V, VSS = 0 V, TA = 25°C 7 mA
AD5231 Data Sheet
Rev. D | Page 4 of 28
Parameter Symbol Conditions Min Typ 1 Max Unit
POWER SUPPLIES
Single-Supply Power Range VDD VSS = 0 V 2.7 5.5 V
Dual-Supply Power Range VDD/VSS ±2.25 ±2.75 V
Positive Supply Current IDD VIH = VDD or VIL = GND 2.7 10 µA
Negative Supply Current
I
SS
IH
DD
IL
VDD = +2.5 V, VSS = −2.5 V
0.5
10
µA
EEMEM Store Mode Current IDD (store) VIH = VDD or VIL = GND,
VSS = GND, ISS ≈ 0
40 mA
ISS (store) VDD = +2.5 V, VSS =2.5 V −40 mA
EEMEM Restore Mode Current7 IDD (restore) VIH = VDD or VIL = GND,
VSS = GND, ISS ≈ 0
0.3 3 9 mA
ISS (restore) VDD = +2.5 V, VSS = −2.5 V −0.3 −3 −9 mA
Power Dissipation8 PDISS VIH = VDD or VIL = GND 0.018 0.05 mW
Power Supply Sensitivity5 PSS ΔVDD = 5 V ± 10% 0.002 0.01 %/%
DYNAMIC CHARACTERISTICS5, 9
Bandwidth BW −3 dB, RAB = 10 kΩ/50 kΩ/
100 kΩ
370/85/44 kHz
Total Harmonic Distortion THDW VA = 1 V rms, VB = 0 V, f = 1 kHz,
RAB = 10 kΩ
0.045 %
VA = 1 V rms, VB = 0 V, f = 1 kHz,
RAB = 50 kΩ, 100 kΩ
0.022 %
VW Settling Time tS VA = VDD, VB = 0 V,
VW = 0.50% error band,
Code 0x000 to 0x200
for RAB = 10 kΩ/50 kΩ/100 kΩ
1.2/3.7/7 µs
Resistor Noise Voltage eN_WB RWB = 5 kΩ, f = 1 kHz 9 nV/√Hz
1 Typical values represent average readings at 25°C and VDD = 5 V.
2 Resistor position nonlinearity error (R-INL) is the deviation from an ideal value measured between the maximum resistance and the minimum resistance wiper
positions. R-DNL measures the relative step change from ideal between successive tap positions. IW ~ 50 µA @ VDD = 2.7 V and IW ~ 400 µA @ VDD = 5 V for the
RAB = 10 kΩ version, IW ~ 50 µA for the RAB = 50 kΩ, and IW ~ 25 µA for the RAB = 100 kΩ version (see Figure 26).
3 INL and DNL are measured at VW with the RDAC configured as a potentiometer divider similar to a voltage output DAC. VA = VDD and VB = VSS. DNL specification limits of
−1 LSB minimum are guaranteed monotonic operating condition (see Figure 27).
4 Resistor Terminal A, Resistor Terminal B, and Resistor Terminal W have no limitations on polarity with respect to each other. Dual-supply operation enables ground-
referenced bipolar signal adjustment.
5 Guaranteed by design and not subject to production test.
6 Common-mode leakage current is a measure of the dc leakage from any Terminal BW to a common-mode bias level of VDD/2.
7 EEMEM restore mode current is not continuous. Current consumed while EEMEM locations are read and transferred to the RDAC register (see Figure 23). To minimize
power dissipation, a NOP Instruction 0 (0x0) should be issued immediately after Instruction 1 (0x1).
8 PDISS is calculated from (IDD × VDD) + (ISS × VSS).
9 All dynamic characteristics use VDD = +2.5 V and VSS = −2.5 V.
Data Sheet AD5231
Rev. D | Page 5 of 28
TIMING CHARACTERISTICS—10 kΩ, 50 kΩ, 100 kΩ VERSIONS
VDD = 3 V to 5.5 V, VSS = 0 V, and −40°C < TA < +85°C, unless otherwise noted.
Table 2.
Parameter Symbol Conditions Min Typ1 Max Unit
INTERFACE TIMING CHARACTERISTICS2, 3
Clock Cycle Time (tCYC) t1 20 ns
CS Setup Time t2 10 ns
CLK Shutdown Time to CS Rise t3 1 tCYC
Input Clock Pulse Width t4, t5 Clock level high or low 10 ns
Data Setup Time t6 From positive CLK transition 5 ns
Data Hold Time t7 From positive CLK transition 5 ns
CS to SDO-SPI Line Acquire t8 40 ns
CS to SDO-SPI Line Release t9 50 ns
CLK to SDO Propagation Delay4 t
10 R
P = 2.2 kΩ, CL < 20 pF 50 ns
CLK to SDO Data Hold Time t11 R
P = 2.2 kΩ, CL < 20 pF 0 ns
CS High Pulse Width5 t12 10 ns
CS High to CS High5 t13 4 tCYC
RDY Rise to CS Fall t14 0 ns
CS Rise to RDY Fall Time t15 0.1 0.15 ms
Store/Read EEMEM Time6 t
16 Applies to instructions 0x2, 0x3, and 0x9 25 ms
Power-On EEMEM Restore Time tEEMEM1 R
AB = 10 kΩ 140 μs
Dynamic EEMEM Restore Time tEEMEM2 R
AB = 10 kΩ 140 μs
WP High or Low to CS Fall Time tWP 40 ns
CS Rise to Clock Rise/Fall Setup t17 10 ns
Preset Pulse Width (Asynchronous) tPRW Not shown in timing diagram 50 ns
Preset Response Time to Wiper Setting tPRESP PR pulsed low to refresh wiper positions 70 μs
FLASH/EE MEMORY RELIABILITY
Endurance7 100 kCycles
Data Retention8 100 Years
1 Typical values represent average readings at 25°C and VDD = 5 V.
2 Guaranteed by design and not subject to production test.
3 See timing diagrams (Figure 3 and Figure 4) for location of measured values. All input control voltages are specified with tR = tF = 2.5 ns (10% to 90% of 3 V) and timed
from a voltage level of 1.5 V. Switching characteristics are measured using both VDD = 3 V and VDD = 35 V.
4 Propagation delay depends on the value of VDD, RPULL-UP, and CL.
5 Valid for commands that do not activate the RDY pin.
6 RDY pin low only for Instructions 2, 3, 8, 9, 10, and the PR hardware pulse: CMD_2, 3 ~ 20 ms; CMD_8 ~ 1 ms; CMD_9, 10 ~ 0.12 ms. Device operation at TA = −40°C and
VDD < 3 V extends the EEMEM store time to 35 ms.
7 Endurance is qualified to 100,000 cycles per JEDEC Standard 22, Method A117 and measured at −40°C, +25°C, and +85°C; typical endurance at +25°C is 700,000 cycles.
8 Retention lifetime equivalent at junction temperature (TJ) = 55°C per JEDEC Standard 22, Method A117. Retention lifetime based on an activation energy of 0.6 eV
derates with junction temperature, as shown in Figure 45 in the Flash/EEMEM Reliability section.
AD5231 Data Sheet
Rev. D | Page 6 of 28
Timing Diagrams
CLK
CPOL = 1
B24* B23–MSB B0–LSB
B23–MSB
HIGH
OR LOW HIGH
OR LOW
B23 B0
B0–LSB
RDY
CPHA = 1
*NO T DEFINED, BUT NORMAL LY LSB O F CHARACTER PREVIOUS LY TRANSMI TT E D.
THE CP OL = 1 M ICROCONT ROLLER COMMAND ALIGNS THE I NCOMI NG DAT A TO THE POSIT I V E E DGE OF THE CL OCK.
SDO
SDI
CS
t
2
t
1
t
5
t
4
t
7
t
6
t
10
t
8
t
14
t
11
t
9
t
12
t
3
t
13
t
17
t
15
t
16
02739-003
Figure 3. CPHA = 1 Timing Diagram
CLK
CPOL = 0
B23–MSB O U T B0–LSB
SDO
B23–MSB I N
B23 B0
HIGH
OR LOW HIGH
OR LOW
B0–LSB
SDI
RDY
CPHA = 0
*NO T DEF INED, BUT NO RM ALLY M S B OF CHARACT E R P REVIOUSL Y RECEIVED.
THE CPOL = 0 MICROCONTROLLER COMMAND ALIGNS THE INCOMING DATA TO THE POSITIVE EDGE OF THE CLOCK.
*
CS
t
2
t
1
t
4
t
5
t
7
t
6
t
10
t
8
t
14
t
11
t
9
t
12
t
3
t
13
t
17
t
15
t
16
02739-004
Figure 4. CPHA = 0 Timing Diagram
Data Sheet AD5231
Rev. D | Page 7 of 28
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 3.
Parameters Ratings
VDD to GND 0.3 V, +7 V
VSS to GND +0.3 V, 7 V
VDD to VSS 7 V
VA, VB, VW to GND VSS0.3 V, VDD + 0.3 V
A–B, AW, B–W
Intermittent1 ±20 mA
Continuous ±2 mA
Digital Input and Output Voltage
to GND
0.3 V, VDD + 0.3 V
Operating Temperature Range2 40°C to +85°C
Maximum Junction Temperature
(TJ max)
150°C
Storage Temperature 65°C to +150°C
Reflow Soldering
Peak Temperature 260°C
Time at Peak Temperature 20 sec to 40 sec
Thermal Resistance
Junction-to-Ambient JA),TSSOP-16
150°C/W
Junction-to-Case JC), TSSOP-16 28°C/W
Package Power Dissipation (TJ max − TA)/θJA
1 Maximum terminal current is bounded by the maximum current handling of the
switches, maximum power dissipation of the package, and maximum applied
voltage across any two of the A, B, and W terminals at a given resistance.
2 Includes programming of nonvolatile memory.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
AD5231 Data Sheet
Rev. D | Page 8 of 28
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
16
15
14
13
12
11
10
9
RDY
V
DD
A
W
TOP VI EW
(No t t o Scal e)
AD5231
1
2
3
4
5
6
7
8
CLK
SDI
SDO
V
SS
GND
T
O1
B
O2
CS
PR
WP
02739-005
Figure 5. Pin Configuration
Table 4. Pin Function Descriptions
Pin No. Mnemonic Description
1 O1 Nonvolatile Digital Output 1. ADDR = 0x1, data bit position D0. For example, to store O1 high, the data bit
format is 0x310001.
2 CLK Serial Input Register Clock Pin. Shifts in one bit at a time on positive clock edges.
3 SDI Serial Data Input Pin. Shifts in one bit at a time on positive clock CLK edges. MSB loaded first.
4 SDO Serial Data Output Pin. Serves readback and daisy-chain functions.
Command 9 and Command 10 activate the SDO output for the readback function, delayed by 24 or 25 clock
pulses, depending on the clock polarity before and after the data-word (see Figure 3, Figure 4, and Table 7).
In other commands, the SDO shifts out the previously loaded SDI bit pattern, delayed by 24 or 25 clock pulses
depending on the clock polarity (see Figure 3 and Figure 4). This previously shifted-out SDI can be used for
daisy-chaining multiple devices.
Whenever SDO is used, a pull-up resistor in the range of 1 kΩ to 10 kΩ is needed.
5 GND Ground Pin. Logic ground reference.
6 VSS Negative Supply. Connect to 0 V for single-supply applications. If VSS is used in dual-supply applications, it must be
able to sink 40 mA for 25 ms when storing data to EEMEM.
7
T
Reserved for factory testing. Connect to V
DD
or V
SS
.
8 B Terminal B of RDAC.
9 W Wiper Terminal of RDAC. ADDR (RDAC) = 0x0.
10 A Terminal A of RDAC.
11 VDD Positive Power Supply Pin.
12 WP Optional Write Protect Pin. When active low, WP prevents any changes to the present contents, except PR and
Instruction 1 and Instruction 8 and refreshes the RDAC register from EEMEM. Execute a NOP instruction before
returning to WP high. Tie WP to VDD, if not used.
13 PR Optional Hardware Override Preset Pin. Refreshes the scratchpad register with current contents of the EEMEM
register. Factory default loads midscale 51210 until EEMEM is loaded with a new value by the user. PR is activated
at the logic high transition. Tie PR to VDD, if not used.
14 CS Serial Register Chip Select Active Low. Serial register operation takes place when CS returns to logic high.
15 RDY Ready. Active-high open-drain output. Identifies completion of Instructions 2, 3, 8, 9, 10, and PR.
16 O2 Nonvolatile Digital Output 2. ADDR = 0x1, data bit position D1. For example, to store O2 high, the data bit
format is 0x310002.
Data Sheet AD5231
Rev. D | Page 9 of 28
TYPICAL PERFORMANCE CHARACTERISTICS
CODE ( Decimal)
0
INL ERRO R ( LSB)
1.5
0
–1.0
1.0
0.5
256 512 768 1024
–0.5
128 384 640 896
TA = +85°C
TA = +25°C
TA = –40° C
02739-006
Figure 6. INL vs. Code, TA = −40°C, +25°C, +85°C Overlay, RAB = 10 k
CODE ( Decimal)
DNL E RROR (L S B)
0
–2.0
2.0
1.0
–1.0
0256 512
768 1024128 384 640 896
–0.5
1.5
0.5
–1.5
V
DD
= 5V, V
SS
= 0V
T
A
= +85°C
T
A
= +25°C
T
A
= –40° C
02739-007
Figure 7. DNL vs. Code, TA = −40°C, +25°C, +85°C Overlay, RAB = 10 k
CODE ( Decimal)
R-INL (LSB)
0
–1.0
1.0
0.5
–0.5
0256 512 768 1024128 384 640 896
TA = +85°C
TA = +25°C
TA = –40° C
VDD = 5V , VSS = 0V
02739-008
Figure 8. R-INL vs. Code, TA = −40°C, +25°C, +85°C Overlay, RAB = 10 k
CODE ( Decimal)
0128 256 384 512 640 768 896 1024
2.0
1.5
1.0
0.5
0
–2.0
–1.5
–1.0
–0.5
R-DNL ( LSB)
V
DD
= 5V, V
SS
= 0V
T
A
= +85°C T
A
= +25°C
T
A
= –40° C
02739-009
Figure 9. R-DNL vs. Code, TA = −40°C, +25°C, +85°C Overlay, RAB = 10 k
CODE ( Decimal)
RHEOSTAT MODE TEMPCO (ppm/°C)
3000
0256 512 768 1024128 384 640 896
2500
2000
1500
1000
500
0
V
DD
= 5.5V , V
SS
= 0V
T
A
= –40° C TO + 85°C
02739-010
Figure 10. (∆RWB/RWB)/∆T × 106
CODE ( Decimal)
POTENTIOMETER MODE TEMPCO (ppm/°C)
100
0256 512 768 1024128 384 640 896
80
60
40
20
0
–20
VDD = 5.5V, VSS = 0V
TA = –40° C TO + 85°C
VB = 0V
VA = 2.00V
02739-011
Figure 11. (∆VW/VW)/∆T × 106
AD5231 Data Sheet
Rev. D | Page 10 of 28
CODE ( Decimal)
R
W
(Ω)
60
0256 512 768 1024
128
384 640 896
50
40
30
20
10
0
V
DD
= 2.7V , V
SS
= 0V
T
A
= 25° C
02739-012
Figure 12. Wiper On Resistance vs. Code
TEMPERATURE (°C)
CURRENT ( µ A)
4
–40 040 80–20 20 60 100
3
2
1
0
–1
IDD @ V DD/VSS = 5V /0V
ISS @ VDD/VSS = 5V /0V
IDD @ V DD/VSS = 2.7V/0V
ISS @ VDD/VSS = 2.7V/0V
02739-013
Figure 13. IDD vs. Temperature, RAB = 10 k
CLOCK FRE QUENCY (MHz)
I
DD
(mA)
0.25
0 2 4 6 8 10 12
0.20
0.15
0.10
0.05
0
V
DD
= 5V
V
SS
= 0V
MIDSCALE
ZERO-SCALE
FULL-SCALE
02739-014
Figure 14. IDD vs. Clock Frequency, RAB = 10 k
FRE QUENCY ( Hz )
2
0
–161k 10k
GAIN (d B)
–2
–4
–12
–6
–8
–10
–14
100k 1M
f–3dB
= 37kHz, R
AB
= 10kΩ
f–3dB
= 44kHz, R
AB
= 100kΩ
f–3dB
= 85kHz, R
AB
= 50kΩ
V
A
= 1mV rms
V
DD
/V
SS
= ±2. 5V
D = MI DS CALE
02739-015
Figure 15. −3 dB Bandwidth vs. Resistance (Figure 32)
FRE QUENCY ( kHz )
0.12
0.01
THD + NOI S E ( %)
0.10
0.08
0.04
00.1 1 10 100
0.06
0.02
V
DD
/V
SS
= ±2. 5V
V
A
= 1V rms
R
AB
= 10kΩ
50kΩ
100kΩ
02739-016
Figure 16. Total Harmonic Distortion vs. Frequency
FREQUENCY (Hz)
0
–501k
GAIN (d B)
–25
100k
10k
–5
–30
–35
–40
–45
–20
–10
–15
1M 10M
CODE = 0x200
0x100
0x80
0x40
0x20
0x10
0x01
0x02
0x04
0x08
02739-017
Figure 17. Gain vs. Frequency vs. Code, RAB = 10 kΩ (Figure 32)
Data Sheet AD5231
Rev. D | Page 11 of 28
FREQUENCY (Hz)
0
–50
1k
GAIN (d B)
100k
10k
–30
–40
–20
–10
1M
0x04
0x01
–60
0x02
CODE = 0x200
0x100
0x80
0x40
0x20
0x10
0x08
02739-018
Figure 18. Gain vs. Frequency vs. Code, RAB = 50 kΩ (Figure 32)
FRE QUENCY ( Hz )
0
–50
1k
GAIN (d B)
100k
10k
–30
–40
–20
–10
1M
0x04
0x01
–60
0x02
CODE = 0x200
0x100
0x80
0x40
0x20
0x10
0x08
02739-019
Figure 19. Gain vs. Frequency vs. Code, RAB = 100 kΩ (Figure 32)
FREQUENCY (Hz)
PSRR ( –dB)
80
100 10k 1M1k 100k 10M
70
50
30
20
0
60
40
10 V
DD
= 5.0V ± 100mV AC
V
SS
= 0V, V
A
= 5V, V
B
= 0V
MEAS URE D AT V
W
WITH CODE = 0x200
R
AB
= 100kΩ
R
AB
= 50kΩ
R
AB
= 10kΩ
02739-020
Figure 20. PSRR vs. Frequency
100µs/DIV
VDD = 5V
VA = 2.25V
VB = 0V VA
VW
0.5V/DIV
EXPECTED
VALUE
MIDSCALE
100
90
10
0%
02739-021
Figure 21. Power-On Reset, VA = 2.25 V, VB = 0 V, Code = 1010101010B
TIME (µs)
V
OUT
(V)
2.55
010 20515 25
2.53
2.51
2.49
2.47
2.45
V
DD
/V
SS
= 5V/ 0V
CODE = 0x200 TO 0x1FF
R
AB
= 10kΩ
R
AB
= 50kΩ
R
AB
= 100kΩ
02739-022
Figure 22. Midscale Glitch Energy, Code 0x200 to 0x1FF
4ms/DIV
5V/DIV
5V/DIV
5V/DIV
CS
CLK
SDI
IDD
20mA/DIV
02739-023
Figure 23. IDD vs. Time when Storing Data to EEMEM
AD5231 Data Sheet
Rev. D | Page 12 of 28
4ms/DIV
5V/DIV
5V/DIV
5V/DIV
CS
CLK
SDI
*SUPPLY CURRE NT RETURNS T O MINI M UM P OWE R CONSUM P TI ON
IF INSTRUCTION 0 (NOP) IS EXECUTED IMMEDIATELY AFTER
INSTRUCT IO N 1 ( RE AD E E M E M ) .
I
DD
*
2mA/DIV
02739-024
Figure 24. IDD vs. Time when Restoring Data from EEMEM
CODE ( Decimal)
100
1
0.01 1024
THEORETICAL—I
WB_MAX
(mA)
0.1
10
896
768
640
512
384128 2560
VA = VB = OPEN
TA = 25° C
RAB = 10kΩ
RAB = 50kΩ
RAB = 100kΩ
02739-025
Figure 25. IWB_MAX vs. Code
Data Sheet AD5231
Rev. D | Page 13 of 28
TEST CIRCUITS
Figure 26 to Figure 35 define the test conditions used in the specifications.
AW
B
NC
IW
DUT
VMS
NC = NO CONNECT
02739-026
Figure 26. Resistor Position Nonlinearity Error
(Rheostat Operation; R-INL, R-DNL)
AW
B
DUT
VMS
V+
V+ = VDD
1LSB = V + /2N
02739-027
Figure 27. Potentiometer Divider Nonlinearity Error (INL, DNL)
AW
B
DUT I
W
V
MS1
V
MS2
V
W
R
W
= [V
MS1
– V
MS2
]/I
W
02739-028
Figure 28. Wiper Resistance
AW
BV
MS
V
A
V
DD
V+
V+ = V
DD
±10%
PSRR (dB) = 20 lo g ΔV
MS
ΔV
DD
PSS (%/%) = ΔV
MS
%
ΔV
DD
%
02739-029
Figure 29. Power Supply Sensitivity (PSS, PSRR)
OFFSET BIAS
OFFSET
GND
AB
DUT
W5V
V
IN
V
OUT
OP279
02739-030
Figure 30. Inverting Gain
OFFSET BIAS
OFFSET
GND A BDUT
W
5V
VIN VOUT
OP279
02739-031
Figure 31. Noninverting Gain
OFFSET
GND
A
B
DUT W
+15V
VOUT
VIN OP42
–15V
+2.5V
02739-032
Figure 32. Gain vs. Frequency
+
DUT
NC
CODE = 0x000
0.1V
V
BIAS
R
SW
=0.1V
I
SW
I
SW
W
B
A
NC = NO CONNECT
02739-033
Figure 33. Incremental On Resistance
I
CM
V
CM
W
B
V
DD
DUT
NC
NC
GNDV
SS
A
NC = NO CONNECT
02739-034
Figure 34. Common-Mode Leakage Current
200µA IOL
200µA IOH
VOH (MIN)
OR
VOL (MAX)
TO OUTPUT
PIN CL
50pF
02739-057
Figure 35. Load Circuit for Measuring VOH and VOL (The diode bridge test
circuit is equivalent to the application circuit with RPULL-UP of 2.2 kΩ)
AD5231 Data Sheet
Rev. D | Page 14 of 28
THEORY OF OPERATION
The AD5231 digital potentiometer is designed to operate as a
true variable resistor replacement device for analog signals that
remain within the terminal voltage range of VSS < VTERM < VDD.
The basic voltage range is limited to VDD − VSS < 5.5 V. The
digital potentiometer wiper position is determined by the
RDAC register contents.
The RDAC register acts as a scratchpad register, allowing as
many value changes as necessary to place the potentiometer
wiper in the correct position. The scratchpad register can be
programmed with any position value using the standard SPI
serial interface mode by loading the complete representative
data-word. Once a desirable position is found, this value can be
stored in an EEMEM register. Thereafter, the wiper position is
always restored to that position for subsequent power-up.
The storing of EEMEM data takes approximately 25 ms; during
this time, the shift register is locked, preventing any changes
from taking place. The RDY pin pulses low to indicate the
completion of this EEMEM storage.
The following instructions facilitate the user’s programming
needs (see Table 7 for details):
0. Do nothing.
1. Restore EEMEM content to RDAC.
2. Store RDAC setting to EEMEM.
3. Store RDAC setting or user data to EEMEM.
4. Decrement 6 dB.
5. Decrement 6 dB.
6. Decrement one step.
7. Decrement one step.
8. Reset EEMEM content to RDAC.
9. Read EEMEM content from SDO.
10. Read RDAC wiper setting from SDO.
11. Write data to RDAC.
12. Increment 6 dB.
13. Increment 6 dB.
14. Increment one step.
15. Increment one step.
SCRATCHPAD AND EEMEM PROGRAMMING
The scratchpad RDAC register directly controls the position of
the digital potentiometer wiper. For example, when the scratchpad
register is loaded with all zeros, the wiper is connected to
Terminal B of the variable resistor. The scratchpad register is a
standard logic register with no restriction on the number of
changes allowed, but the EEMEM registers have a program
erase/write cycle limitation (see the Flash/EEMEM Reliability
section).
BASIC OPERATION
The basic mode of setting the variable resistor wiper position
(programming the scratchpad register) is accomplished by
loading the serial data input register with Instruction 11 (0xB),
Address 0, and the desired wiper position data. When the
proper wiper position is determined, the user can load the serial
data input register with Instruction 2 (0x2), which stores the
wiper position data in the EEMEM register. After 25 ms, the
wiper position is permanently stored in the nonvolatile
memory. Table 5 provides a programming example listing the
sequence of serial data input (SDI) words with the serial data
output appearing at the SDO pin in hexadecimal format.
Table 5. Set and Store RDAC Data to EEMEM Register
SDI
SDO
Action
0xB00100 0xXXXXXX Writes data 0x100 to the RDAC
register, Wiper W moves to 1/4
full-scale position.
0x20XXXX 0xB00100 Stores RDAC register content into
the EEMEM register.
At system power-on, the scratchpad register is automatically
refreshed with the value previously stored in the EEMEM
register. The factory-preset EEMEM value is midscale, but
it can be changed by the user thereafter.
During operation, the scratchpad (RDAC) register can be
refreshed with the EEMEM register data with Instruction 1
(0x1) or Instruction 8 (0x8). The RDAC register can also be
refreshed with the EEMEM register data under hardware
control by pulsing the PR pin. The PR pulse first sets the wiper
at midscale when brought to logic zero, and then, on the
positive transition to logic high, it reloads the RDAC wiper
register with the contents of EEMEM.
Many additional advanced programming commands are
available to simplify the variable resistor adjustment process
(see Table 7). For example, the wiper position can be changed
one step at a time using the increment/decrement instruction or
by 6 dB with the shift left/right instruction. Once an increment,
decrement, or shift instruction has been loaded into the shift
register, subsequent CS strobes can repeat this command.
A serial data output SDO pin is available for daisy-chaining and
for readout of the internal register contents.
EEMEM PROTECTION
The write protect (WP) pin disables any changes to the
scratchpad register contents, except for the EEMEM setting,
which can still be restored using Instruction 1, Instruction 8,
and the PR pulse. Therefore, WP can be used to provide a
hardware EEMEM protection feature. To disable WP, it is
recommended to execute a NOP instruction before returning
WP to logic high.
Data Sheet AD5231
Rev. D | Page 15 of 28
DIGITAL INPUT/OUTPUT CONFIGURATION
All digital inputs are ESD-protected, high input impedance that
can be driven directly from most digital sources. Active at logic
low, PR and WP must be tied to VDD if they are not used. No
internal pull-up resistors are present on any digital input pins.
The SDO and RDY pins are open-drain digital outputs that
need pull-up resistors only if these functions are used. A resistor
value in the range of 1 kΩ to 10 kΩ is a proper choice that
balances the dissipation and switching speed.
The equivalent serial data input and output logic is shown in
Figure 36. The open-drain output SDO is disabled whenever
chip-select CS is in logic high. ESD protection of the digital
inputs is shown in Figure 37 and Figure 38.
COUNTER
SERIAL
REGISTER
CLK
SDI
5V
R
PULL-UP
SDO
GND
PR WP
AD5231
CS
COMMAND
PROCESSOR
AND ADDRESS
DECODE
VALID
COMMAND
02739-035
Figure 36. Equivalent Digital Input-Output Logic
LOGIC
PINS
V
DD
GND
INPUT
300Ω
02739-036
Figure 37. Equivalent ESD Digital Input Protection
GND
WP
V
DD
INPUT
300Ω
02739-037
Figure 38. Equivalent WP Input Protection
SERIAL DATA INTERFACE
The AD5231 contains a 4-wire SPI-compatible digital interface
(SDI, SDO, CS, and CLK). It uses a 24-bit serial data-word
loaded MSB first. The format of the SPI-compatible word is
shown in Table 6. The chip-select CS pin must be held low until
the complete data-word is loaded into the SDI pin. When CS
returns high, the serial data-word is decoded according to the
instructions in Table 7. The command bits (Cx) control the
operation of the digital potentiometer. The address bits (Ax)
determine which register is activated. The data bits (Dx) are the
values that are loaded into the decoded register.
The AD5231 has an internal counter that counts a multiple of
24 bits (a frame) for proper operation. For example, AD5231
works with a 48-bit word, but it cannot work properly with a
23-bit or 25-bit word. In addition, AD5231 has a subtle feature
that, if CS is pulsed without CLK and SDI, the part repeats the
previous command (except during power-up). As a result, care
must be taken to ensure that no excessive noise exists in the
CLK or CS line that might alter the effective number of bits
(ENOB) pattern. Also, to prevent data from mislocking (due
to noise, for example), the counter resets if the count is not a
multiple of four when CS goes high.
The SPI interface can be used in two slave modes: CPHA = 1,
CPOL = 1 and CPHA = 0, CPOL = 0. CPHA and CPOL refer to
the control bits that dictate SPI timing in the following
MicroConverters® and microprocessors: ADuC812/ADuC824,
M68HC11, and MC68HC16R1/916R1.
DAISY-CHAIN OPERATION
The serial data output pin (SDO) serves two purposes. It can be
used to read the contents of the wiper setting and EEMEM
values using Instruction 10 and Instruction 9, respectively. The
remaining instructions (0 to 8, 11 to 15) are valid for daisy-
chaining multiple devices in simultaneous operations. Daisy-
chaining minimizes the number of port pins required from
the controlling IC (see Figure 39). The SDO pin contains an
open-drain N-Ch FET that requires a pull-up resistor if this
function is used. As shown in Figure 39, users need to tie the
SDO pin of one package to the SDI pin of the next package.
Users might need to increase the clock period, because the
pull-up resistor and the capacitive loading at the SDO to SDI
interface might require additional time delay between sub-
sequent packages. When two AD5231s are daisy-chained,
48 bits of data are required. The first 24 bits go to U2 and the
second 24 bits go to U1. The CS should be kept low until all
48 bits are clocked into their respective serial registers. The CS
is then pulled high to complete the operation.
SDI SDO
CLK
RP
2kΩ
µC SDI SDO
CLK
U1 U2
AD5231 AD5231
CS
CS
+V
02739-038
Figure 39. Daisy-Chain Configuration Using SDO
AD5231 Data Sheet
Rev. D | Page 16 of 28
TERMINAL VOLTAGE OPERATION RANGE
The AD5231’s positive VDD and negative VSS power supplies
define the boundary conditions for proper 3-terminal digital
potentiometer operation. Supply signals present on the A, B,
and W terminals that exceed VDD or VSS are clamped by the
internal forward-biased diodes (see Figure 40).
The ground pin of the AD5231 device is primarily used as a
digital ground reference, which needs to be tied to the common
ground of the PCB. The digital input control signals to the
AD5231 must be referenced to the device ground pin (GND)
and satisfy the logic level defined in the Specifications section.
An internal level-shift circuit ensures that the common-mode
voltage range of the three terminals extends from VSS to VDD,
regardless of the digital input level.
V
SS
V
DD
A
W
B
02739-039
Figure 40. Maximum Terminal Voltages Set by VDD and VSS
POWER-UP SEQUENCE
Because there are diodes to limit the voltage compliance at the
A, B, and W terminals (Figure 40), it is important to power
VDD/VSS first before applying any voltage to Terminal A,
Terminal B, and Terminal W. Otherwise, the diode is forward-
biased such that VDD/VSS are powered unintentionally and
might affect the rest of the users circuit. The ideal power-up
sequence is GND, VDD, VSS, digital inputs, and VA/VB/VW. The
order of powering VA, VB, VW, and digital inputs is not
important as long as they are powered after VDD/VSS.
Regardless of the power-up sequence and the ramp rates of the
power supplies, once VDD/VSS are powered, the power-on preset
remains effective, which restores the EEMEM value to the
RDAC register.
LATCHED DIGITAL OUTPUTS
A pair of digital outputs, O1 and O2, is available on the
AD5231. These outputs provide a nonvolatile Logic 0 or Logic 1
setting. O1 and O2 are standard CMOS logic outputs, shown in
Figure 41. These outputs are ideal to replace the functions often
provided by DIP switches. In addition, they can be used to drive
other standard CMOS logic-controlled parts that need an
occasional setting change. Pin O1 and Pin O2 default to Logic 1,
and they can drive up to 50 mA of load at 5 V/25°C.
V
DD
GND
OUTPUTS
O1 AND O2
PINS
02739-040
Figure 41. Logic Outputs O1 and O2
Data Sheet AD5231
Rev. D | Page 17 of 28
In Table 6, command bits are C0 to C3, address bits are A3 to A0, Data Bit D0 to Data Bit D9 are applicable to RDAC, and D0 to D15 are
applicable to EEMEM.
Table 6. AD5231 24-Bit Serial Data-Word
MSB Command Byte 0
Data Byte 1
Data Byte 0
LSB
RDAC C3 C2 C1 C0 0 0 0 0 X X X X X X D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
EEMEM
C3
C2
C1
C0
A3
A2
A1
A0
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
Command instruction codes are defined in Table 7.
Table 7. Command/Operation Truth Table1, 2, 3
Instruction
Number
Command Byte 0 Data Byte 1 Data Byte 0
Operation
B23 B16 B15 B8 B7 B0
C3 C2 C1 C0 A3 A2 A1 A0 X D9 D8 D7 D0
0 0 0 0 0 X X X X X X X X X NOP: Do nothing. See Table 15.
1 0 0 0 1 0 0 0 0 X X X X X Restore EEMEM(0) contents to RDAC register.
This command leaves the device in the read
program power state. To return the part to
the idle state, perform NOP instruction 0. See
Table 15.
2 0 0 1 0 0 0 0 0 X X X X X
Store Wiper Setting: Store RDAC setting to
EEMEM(0). See Table 14.
3
4
0 0 1 1 A3 A2 A1 A0 D15 D8 D7 D0
Store contents of Data Bytes 0 and 1 (total
16 bits) to EEMEM (ADDR 1to ADDR 15). See
Table 17.
4
5
0 1 0 0 0 0 0 0 X X X X X Decrement RDAC by 6 dB.
55 0 1 0 1 X X X X X X X X X Same as Instruction 4.
65 0 1 1 0 0 0 0 0 X X X X X Decrement RDAC by 1 position.
75 0 1 1 1 X X X X X X X X X Same as Instruction 6.
8 1 0 0 0 X X X X X X X X X Reset: Restore RDAC with EEMEM (0) value.
9 1 0 0 1 A3 A2 A1 A0 X X X X X Read EEMEM (ADDR 0 to ADDR 15) from SDO
output in the next frame. See Table 18.
10
1
0
1
0
0
0
0
0
X
X
X
X
X
Read RDAC wiper setting from SDO output
in the next frame. See Table 19.
11 1 0 1 1 0 0 0 0 X D9 D8 D7 D0
Write contents of Data Bytes 0 and 1 (total
10 bits) to RDAC. See Table 13.
125 1 1 0 0 0 0 0 0 X X X X X Increment RDAC by 6 dB. See Table 16.
135 1 1 0 1 X X X X X X X X X Same as Instruction 12.
145 1 1 1 0 0 0 0 0 X X X X X Increment RDAC by 1 position. See Table 14.
155 1 1 1 1 X X X X X X X X X Same as Instruction 14.
1 The SDO output shifts out the last 24 bits of data clocked into the serial register for daisy-chain operation. Exception: for any instruction following Instruction 9 or
Instruction 10, the selected internal register data is present in Data Byte 0 and Data Byte 1. The instruction following 9 and 10 must also be a full 24-bit data-word to
completely clock out the contents of the serial register.
2 The RDAC register is a volatile scratchpad register that is refreshed at power-on from the corresponding nonvolatile EEMEM register.
3 Execution of these operations takes place when the CS strobe returns to logic high.
4 Instruction 3 writes two data bytes (16 bits of data) to EEMEM. In the case of 0 addresses, only the last 10 bits are valid for wiper position setting.
5 The increment, decrement, and shift instructions ignore the contents of the shift register Data Byte 0 and Data Byte 1.
AD5231 Data Sheet
Rev. D | Page 18 of 28
ADVANCED CONTROL MODES
The AD5231 digital potentiometer includes a set of user
programming features to address the wide number of
applications for these universal adjustment devices.
Key programming features include:
Scratchpad programming to any desirable values
Nonvolatile memory storage of the scratchpad RDAC register
value in the EEMEM register
Increment and decrement instructions for the RDAC wiper
register
Left and right bit shift of the RDAC wiper register to achieve
±6 dB level changes
28 extra bytes of user-addressable nonvolatile memory
Linear Increment and Decrement Instructions
The increment and decrement instructions (14, 15, 6, and 7) are
useful for linear step-adjustment applications. These commands
simplify microcontroller software coding by allowing the
controller to send just an increment or decrement command to
the device.
For an increment command, executing Instruction 14 with the
proper address automatically moves the wiper to the next
resistance segment position. Instruction 15 performs the same
function, except that the address does not need to be specified.
Logarithmic Taper Mode Adjustment
Four programming instructions produce logarithmic taper
increment and decrement of the wiper. These settings are
activated by the 6 dB increment and 6 dB decrement
instructions (12, 13, 4, and 5). For example, starting at zero
scale, executing the increment Instruction 12 eleven times
moves the wiper in 6 dB per step from 0% to full scale, RAB. The
6 dB increment instruction doubles the value of the RDAC
register contents each time the command is executed. When the
wiper position is near the maximum setting, the last 6 dB
increment instruction causes the wiper to go to the full-scale
1023 code position. Further 6 dB per increment instructions do
not change the wiper position beyond its full scale.
The 6 dB step increments and 6 dB step decrements are
achieved by shifting the bit internally to the left or right,
respectively. The following information explains the nonideal
±6 dB step adjustment under certain conditions. Table 8
illustrates the operation of the shifting function on the RDAC
register data bits. Each table row represents a successive shift
operation. Note that the left-shift 12 and 13 instructions were
modified such that, if the data in the RDAC register is equal to
zero and the data is shifted left, the RDAC register is then set to
Code 1. Similarly, if the data in the RDAC register is greater
than or equal to midscale and the data is shifted left, then the
data in the RDAC register is automatically set to full scale. This
makes the left-shift function as ideal a logarithmic adjustment
as possible.
The right-shift 4 and 5 instructions are ideal only if the LSB is 0
(ideal logarithmic = no error). If the LSB is 1, the right-shift
function generates a linear half-LSB error, which translates to
a number-of-bits dependent logarithmic error, as shown in
Figure 42. The plot shows the error of the odd numbers of bits
for the AD5231.
Table 8. Detail Left-Shift and Right-Shift Functions
for 6 dB Step Increment and Decrement
Left-Shift
(+6 dB/step)
Left-Shift Right-Shift
Right-Shift
(–6 dB/step)
00 0000 0000 11 1111 1111
00 0000 0001 01 1111 1111
00 0000 0010 00 1111 1111
00 0000 0100 00 0111 1111
00 0000 1000 00 0011 1111
00 0001 0000 00 0001 1111
00 0010 0000 00 0000 1111
00 0100 0000 00 0000 0111
00 1000 0000
00 0000 0011
01 0000 0000 00 0000 0001
10 0000 0000 00 0000 0000
11 1111 1111 00 0000 0000
11 1111 1111 00 0000 0000
Actual conformance to a logarithmic curve between the data
contents in the RDAC register and the wiper position for each
right-shift 4 and 5 command execution contains an error only
for odd numbers of bits. Even numbers of bits are ideal. The
graph in Figure 42 shows plots of Log_Error [20 × log10
(error/code)] for the AD5231. For example, Code 3 Log_Error
= 20 × log10 (0.5/3) = −15.56 dB, which is the worst case. The
plot of Log_Error is more significant at the lower codes.
CODE ( From 1 t o 1023 b y 2.0 × 10
3
)
0
(dB)
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1
0
–40
–20
–60
–80
02739-041
Figure 42. Plot of Log_Error Conformance for Odd Numbers of Bits Only
(Even Numbers of Bits Are Ideal)
Data Sheet AD5231
Rev. D | Page 19 of 28
Using Additional Internal Nonvolatile EEMEM
The AD5231 contains additional user EEMEM registers for
storing any 16-bit data such as memory data for other compo-
nents, look-up tables, or system identification information.
Table 9 provides an address map of the internal storage registers
shown in the functional block diagram as EEMEM1, EEMEM2,
and 28 bytes (14 addresses × 2 bytes each) of user EEMEM.
Table 9. EEMEM Address Map
Address EEMEM for
0000 RDAC1, 2
0001 O1 and O23
0010 USER14
0011 USER2
1110 USER13
1111 USER14
1 RDAC data stored in EEMEM location is transferred to the RDAC register at
power-on, or when Instruction 1, Instruction 8, or PR are executed.
2 Execution of Instruction 1 leaves the device in the read mode power
consumption state. After the last Instruction 1 is executed, the user should
perform a NOP, Instruction 0 to return the device to the low power idling
state.
3 O1 and O2 data stored in EEMEM locations is transferred to the
corresponding digital register at power-on, or when Instruction 1 and
Instruction 8 are executed.
4 USERx are internal nonvolatile EEMEM registers available to store 16-bit
information using Instruction 3 and restore the contents using Instruction 9.
RDAC STRUCTURE
The patent-pending RDAC contains multiple strings of equal
resistor segments with an array of analog switches that act as the
wiper connection. The number of positions is the resolution of
the device. The AD5231 has 1024 connection points, allowing it
to provide better than 0.1% settability resolution. Figure 43
shows an equivalent structure of the connections among the
three terminals of the RDAC. The SWA and SWB are always on,
while the switches SW(0) to SW(2N1) are on one at a time,
depending on the resistance position decoded from the data
bits. Because the switch is not ideal, there is a 15 Ω wiper
resistance, RW. Wiper resistance is a function of supply voltage
and temperature. The lower the supply voltage or the higher the
temperature, the higher the resulting wiper resistance. Users
should be aware of the wiper resistance dynamics if accurate
prediction of the output resistance is needed.
SW(1)
SW(0)
SW
B
B
SW
A
SW(2
N
–1)
SW(2
N
–2)
A
W
R
S
R
S
R
S
R
S
= R
AB
/2
N
DIGITAL
CIRCUITRY
OMITTED FOR
CLARITY
RDAC
WIPER
REGISTER
AND
DECODER
02739-042
Figure 43. Equivalent RDAC Structure (Patent Pending)
Table 10. Nominal Individual Segment Resistor (RS)
Device
Resolution
10 k
Version
50 kΩ
Version
100 kΩ
Version
10-Bit 9.8 Ω 48.8 Ω 97.6 Ω
PROGRAMMING THE VARIABLE RESISTOR
Rheostat Operation
The nominal resistance of the RDAC between Terminal A and
Terminal B, RAB, is available with 10 kΩ, 50 kΩ, and 100 kΩ
with 1024 positions (10-bit resolution). The final digit(s) of the
part number determine the nominal resistance value, for
example, 10 kΩ = 10; 50 kΩ = 50; 100 kΩ = C.
The 10-bit data-word in the RDAC latch is decoded to select
one of the 1024 possible settings. The following discussion
describes the calculation of resistance RWB at different codes of a
10 kΩ part. For VDD = 5 V, the wiper’s first connection starts at
Terminal B for data 0x000. RWB(0) is 15 Ω because of the wiper
resistance, and because it is independent of the nominal
resistance. The second connection is the first tap point where
RWB (1) becomes 9.7 Ω + 15 Ω = 24.7 Ω for data 0x001. The
third connection is the next tap point representing RWB (2) =
19.4 Ω + 15 Ω = 34.4 Ω for data 0x002 and so on. Each LSB data
value increase moves the wiper up the resistor ladder until the
last tap point is reached at RWB (1023) = 10,005 Ω. See Figure 43
for a simplified diagram of the equivalent RDAC circuit. When
RWB is used, Terminal A can be left floating or tied to the wiper.
AD5231 Data Sheet
Rev. D | Page 20 of 28
CODE ( Decimal)
100
75
001023256
R
WA
(D), R
WB
(D); ( % of No min al R
AB
)
512 768
50
25
R
WB
R
WA
02739-043
Figure 44. RWA(D) and RWB(D) vs. Decimal Code
The general equation that determines the programmed output
resistance between W and B is
W
AB
WB RR
D
DR +×= 1024
)(
(1)
where:
D is the decimal equivalent of the data contained in the RDAC
register.
RAB is the nominal resistance between Terminal A and
Terminal B.
RW is the wiper resistance.
For example, the output resistance values in Table 11 are set
for the given RDAC latch codes with VDD = 5 V (applies to
RAB = 10 kΩ digital potentiometers).
Table 11. RWB (D) at Selected Codes for RAB = 10 kΩ
D (DEC) RWB(D) (Ω) Output State
1023 10,005 Full scale
512 50,015 Midscale
1 24.7 1 LSB
0 15 Zero scale (wiper contact resistor)
Note that, in the zero-scale condition, a finite wiper resistance
of 15 Ω is present. Care should be taken to limit the current
flow between W and B in this state to no more than 20 mA to
avoid degradation or possible destruction of the internal switches.
Like the mechanical potentiometer that the RDAC replaces, the
AD5231 part is totally symmetrical. The resistance between
Wiper W and Terminal A also produces a digitally controlled
complementary resistance, RWA . Figure 44 shows the symmetrical
programmability of the various terminal connections. When
RWA is used, Terminal B can be left floating or tied to the wiper.
Setting the resistance value for RWA starts at a maximum value
of resistance and decreases as the data loaded in the latch is
increased in value.
The general transfer equation for this operation is
W
AB
WB
RR
D
DR +×
=1024
1024
)(
(2)
For example, the output resistance values in Table 12 are set for
the RDAC latch codes with VDD = 5 V (applies to RAB = 10 kΩ
digital potentiometers).
Table 12. RWA(D) at Selected Codes for RAB = 10 kΩ
D (DEC) RWA(D) (Ω) Output State
1023 24.7 Full scale
512
5015
Midscale
1 10005 1 LSB
0 10,015 Zero scale
The typical distribution of RAB from device to device matches
tightly when they are processed in the same batch. When
devices are processed at a different time, device-to-device
matching becomes process-lot dependent and exhibits a −40%
to +20% variation. The change in RAB with temperature has a
600 ppm/°C temperature coefficient.
PROGRAMMING THE POTENTIOMETER DIVIDER
Voltage Output Operation
The digital potentiometer can be configured to generate an
output voltage at the wiper terminal that is proportional to the
input voltages applied to Terminal A and Terminal B. For
example, connecting Terminal A to 5 V and Terminal B to
ground produces an output voltage at the wiper that can be any
value from 0 V to 5 V. Each LSB of voltage is equal to the
voltage applied across Terminals A–B divided by the 2N position
resolution of the potentiometer divider.
Because AD5231 can also be supplied by dual supplies, the
general equation defining the output voltage at VW with respect
to ground for any given input voltages applied to Terminal A
and Terminal B is
B
AB
W
VV
D
DV +×
=1024
)(
(3)
Equation 3 assumes that VW is buffered so that the effect of
wiper resistance is minimized. Operation of the digital
potentiometer in divider mode results in more accurate
operation over temperature. Here, the output voltage is
dependent on the ratio of the internal resistors and not the
absolute value; therefore, the drift improves to 15 ppm/°C.
There is no voltage polarity restriction between Terminal A,
Terminal B, and Terminal W as long as the terminal voltage
(VTERM) stays within VSS < VTERM < VDD.
Data Sheet AD5231
Rev. D | Page 21 of 28
PROGRAMMING EXAMPLES
The following programming examples illustrate a typical
sequence of events for various features of the AD5231. See
Table 7 for the instructions and data-word format. The
instruction numbers, addresses, and data appearing at SDI
and SDO pins are in hexadecimal format.
Table 13. Scratchpad Programming
SDI SDO Action
0xB00100 0xXXXXXX Writes data 0x100 into RDAC register,
Wiper W moves to 1/4 full-scale position.
Table 14. Incrementing RDAC Followed by Storing the
Wiper Setting to EEMEM
SDI SDO Action
0xB00100 0xXXXXXX Writes data 0x100 into RDAC register,
Wiper W moves to 1/4 full-scale
position.
0xE0XXXX 0xB00100 Increments RDAC register by one to
0x101.
0xE0XXXX
0xE0XXXX
Increments RDAC register by one to
0x102. Continue until desired wiper
position is reached.
0x20XXXX 0xXXXXXX Stores RDAC register data into
EEMEM(0). Optionally tie WP to GND
to protect EEMEM values.
The EEMEM value for the RDAC can be restored by power-on,
by strobing the PR pin, or by programming, as shown in
Table 15.
Table 15. Restoring the EEMEM Value to the RDAC Register
SDI SDO Action
0x10XXXX 0xXXXXXX Restores the EEMEM(0) value to the
RDAC register.
0x00XXXX 0x10XXXX NOP. Recommended step to minimize
power consumption.
Table 16. Using Left-Shift by One to Increment 6 dB Step
SDI SDO Action
0xC0XXXX 0xXXXXXX Moves the wiper to double the
present data contained in the RDAC
register.
Table 17. Storing Additional User Data in EEMEM
SDI SDO Action
0x32AAAA 0xXXXXXX Stores data 0xAAAA in the extra
EEMEM location USER1. (Allowable to
address in 14 locations with a
maximum of 16 bits of data.)
0x335555 0x32AAAA Stores data 0x5555 in the extra
EEMEM location USER2. (Allowable to
address in 14 locations with a
maximum of 16 bits of data.)
Table 18. Reading Back Data from Memory Locations
SDI SDO Action
0x92XXXX 0xXXXXXX Prepares data read from EEMEM(2)
location.
0x00XXXX 0x92AAAA NOP Instruction 0 sends a 24-bit word
out of SDO, where the last 16 bits
contain the contents in the EEMEM(2)
location. The NOP command ensures
that the device returns to the idle
power dissipation state.
Table 19. Reading Back Wiper Settings
SDI SDO Action
0xB00200 0xXXXXXX Writes RDAC to midscale.
0xC0XXXX 0xB00200 Doubles RDAC from midscale to full
scale (left-shift instruction).
0xA0XXXX 0xC0XXXX Prepares reading wiper setting from
RDAC register.
0xXXXXXX
0xA003FF
Reads back full-scale value from SDO.
AD5231 Data Sheet
Rev. D | Page 22 of 28
FLASH/EEMEM RELIABILITY
The Flash/EE memory array on the AD5231 is fully qualified
for two key Flash/EE memory characteristics, namely Flash/EE
memory cycling endurance and Flash/EE memory data
retention.
Endurance quantifies the ability of the Flash/EE memory to be
cycled through many program, read, and erase cycles. In real
terms, a single endurance cycle is composed of four
independent, sequential events. These events are defined as
Initial page erase sequence
Read/verify sequence
Byte program sequence
Second read/verify sequence
During reliability qualification, Flash/EE memory is cycled
from 0x000 to 0x3FF until a first fail is recorded signifying the
endurance limit of the on-chip Flash/EE memory.
As indicated in the Specifications section, the AD5231 Flash/EE
memory endurance qualification has been carried out in
accordance with JEDEC Specification A117 over the industrial
temperature range of −40°C to +85°C. The results allow the
specification of a minimum endurance figure over supply and
temperature of 100,000 cycles, with an endurance figure of
700,000 cycles being typical of operation at 25°C.
Retention quantifies the ability of the Flash/EE memory to
retain its programmed data over time. Again, the AD5231 has
been qualified in accordance with the formal JEDEC Retention
Lifetime Specification (A117) at a specific junction temperature
(TJ = 55°C). As part of this qualification procedure, the
Flash/EE memory is cycled to its specified endurance limit,
described previously, before data retention is characterized.
This means that the Flash/EE memory is guaranteed to retain
its data for its full specified retention lifetime every time the
Flash/EE memory is reprogrammed. It should also be noted
that retention lifetime, based on an activation energy of 0.6 eV,
derates with TJ, as shown in Figure 45. For example, the data is
retained for 100 years at 55°C operation, but reduces to 15 years
at 85°C operation. Beyond these limits, the part must be
reprogrammed so that the data can be restored.
300
250
040
RET E NTION (Y ears)
200
150
100
50
50 60 70 80 90 100 110
T
J
JUNCTIONTEMPERATURE C)
ANALOG DE V ICES
TY P ICAL P E RFO RM ANCE
AT T
J
= 55° C
02739-044
Figure 45. Flash/EE Memory Data Retention
Data Sheet AD5231
Rev. D | Page 23 of 28
APPLICATIONS
BIPOLAR OPERATION FROM DUAL SUPPLIES
The AD5231 can be operated from dual supplies ±2.5 V, which
enables control of ground referenced ac signals or bipolar
operation. AC signals as high as VDD/VSS can be applied directly
across Terminal A to Terminal B with output taken from
Terminal W. See Figure 46 for a typical circuit connection.
±2.5V p-p
AD5231
V
SS
GND
SDI
CLK
SS
SCLK
MOSI
GND
µC
±1.25V p-p
V
DD
V
DD
+2.5V
–2.5V
CS
D = MI DS CALE
A
W
B
02739-045
Figure 46. Bipolar Operation from Dual Supplies
HIGH VOLTAGE OPERATION
The digital potentiometer can be placed directly in the feedback
or input path of an op amp for gain control, provided that the
voltage across Terminals AB, Terminals WA, or Terminals
WB does not exceed |5 V|. When high voltage gain is needed,
users should set a fixed gain in an op amp operated at a higher
voltage and let the digital potentiometer control the adjustable
input. Figure 47 shows a simple implementation.
R2R
5V
AD5231
AW
B
15V
V+
V– V
O
0VTO15V
A1
+
C
C
2.2pF
02739-046
Figure 47. 15 V Voltage Span Control
BIPOLAR PROGRAMMABLE GAIN AMPLIFIER
There are several ways to achieve bipolar gain. Figure 48 shows
one versatile implementation. Digital potentiometer U1 sets the
adjustment range; the wiper voltage VW2 can, therefore, be
programmed between Vi and −KVi at a given U2 setting. For
linear adjustment, configure A2 as a noninverting amplifier and
the transfer function becomes
+××
+= KK
D
R1
R2
V
V
2
I
O
)1(
1024
1
(4)
where:
K is the ratio of RWB/RWA that is set by U1.
D is the decimal equivalent of the input code.
V+
V–
OP2177
AD5231
V+
V–
OP2177
AD5231
Vi A
W
B–KVi
AB
W
V
DD
V
O
V
SS
R1
R2
A
U2
A2
U1
C
C
2.2pF
V
DD
V
SS
02739-047
Figure 48. Bipolar Programmable Gain Amplifier
In the simpler (and much more usual) case where K = 1,
a pair of matched resistors can replace U1. Equation 4 can be
simplified to
×
+= 1
1024
2
1
2
D
R1
R2
V
V
I
O
(5)
Table 20 shows the result of adjusting D with A2 configured as a
unity gain, a gain of 2, and a gain of 10. The result is a bipolar
amplifier with linearly programmable gain and 1024-step
resolution.
Table 20. Result of Bipolar Gain Amplifier
D R1 = ∞, R2 = 0 R1 = R2 R2 = 9 × R1
0 −1 −2 10
256 0.5 −1 −5
512 0 0 0
768 0.5 1 5
1023 0.992 1.984 9.92
10-BIT BIPOLAR DAC
If the circuit in Figure 48 is changed with the input taken from a
voltage reference and A2 configured as a buffer, a 10-bit bipolar
DAC can be realized. Compared to the conventional DAC, this
circuit offers comparable resolution but not the precision
because of the wiper resistance effects. Degradation of the
nonlinearity and temperature coefficient is prominent near
both ends of the adjustment range. On the other hand, this
circuit offers a unique nonvolatile memory feature that in some
cases outweighs any shortfall in precision.
The output of this circuit is
REF
O
V
D
V×
= 1
1024
2
2
(6)
AD5231 Data Sheet
Rev. D | Page 24 of 28
V+
V–
AD8552
AD5231
V
O
V+
V–
AD8552
–2.5VREF
BA
W
A1
U1
+2.5VREF
V
OUT
V
IN
TRIM
GND
ADR421
+5V
–5V
–5V
+5V
R R
A2
+5V
02739-048
Figure 49. 10-Bit Bipolar DAC
10-BIT UNIPOLAR DAC
Figure 50 shows a unipolar 10-bit DAC using AD5231. The
buffer is needed to drive various leads.
AD5231
V+
V–
AD8601
W
A1
GND
AD1582
5V
5V
U1 3A
BV
O
1
2
V
OUT
V
IN
02739-049
Figure 50. 10-Bit Unipolar DAC
PROGRAMMABLE VOLTAGE SOURCE WITH
BOOSTED OUTPUT
For applications that require high current adjustment, such as a
laser diode driver or tunable laser, a boosted voltage source can
be considered (see Figure 51).
AD5231
V+
V–
W
AD8601
A
B
VIN VOUT
IL
2N7002 RBIAS
SIGNAL CC
LD
U2
02739-058
Figure 51. Programmable Booster Voltage Source
In this circuit, the inverting input of the op amp forces the VOUT
to be equal to the wiper voltage set by the digital potentiometer.
The load current is then delivered by the supply via the
N-Ch FET N1. N1 power handling must be adequate to dissipate
(Vi − VO) × IL power. This circuit can source a maximum of
100 mA with a 5 V supply.
For precision applications, a voltage reference such as ADR421,
ADR03, or ADR370 can be applied at Terminal A of the digital
potentiometer.
PROGRAMMABLE CURRENT SOURCE
A programmable current source can be implemented with the
circuit shown in Figure 52.
V+
V–
OP1177
U2
VIN
SLEEP
REF191
GND
VOUT
3
2
4
6
U1
AD5231
W
A
B
VL
IL
+5V
–5V
+5V
+
–2.048V TOVL
0V T O (2. 048V + VL)
RS
102Ω
C1
1µF
RL
100Ω
02739-051
Figure 52. Programmable Current Source
REF191 is a unique low supply, headroom precision reference
that can deliver the 20 mA needed at 2.048 V. The load current
is simply the voltage across Terminals B–W of the digital
potentiometer divided by RS:
1024×
×
=
S
REF
LR
D
V
I
(7)
The circuit is simple, but be aware that there are two issues.
First, dual-supply op amps are ideal because the ground
potential of REF191 can swing from −2.048 V at zero scale to VL
at full scale of the potentiometer setting. Although the circuit
works under single-supply, the programmable resolution of the
system is reduced. Second, the voltage compliance at VL is
limited to 2.5 V or equivalently a 125 Ω load. Should higher
voltage compliance be needed, users can consider digital
potentiometers AD5260, AD5280, and AD7376. Figure 53
shows an alternate circuit for high voltage compliance.
To achieve higher current, such as when driving a high power
LED, the user can replace the UI with an LDO, reduce RS, and
add a resistor in series with the digital potentiometer’s
A terminal. This limits the potentiometer’s current and
increases the current adjustment resolution.
Data Sheet AD5231
Rev. D | Page 25 of 28
PROGRAMMABLE BIDIRECTIONAL CURRENT
SOURCE
For applications that require bidirectional current control or
higher voltage compliance, a Howland current pump can be a
solution. If the resistors are matched, the load current is
( )
WL V
R2B
R1
R2BR2A
I×
+
=
(8)
–15V
OP2177
V+
V–
+15V
+
C1
10pF
R2
15kΩ
R1
150kΩ
RL
500Ω
R2B
50Ω
VL
R1
150kΩ R2A
14.95kΩ
IL
OP2177
V+
V–
+15V
+
–15V
A1
AD5231
A
B W
+2.5V
–2.5V
A2
02739-052
Figure 53. Programmable Bidirectional Current Source
R2B, in theory, can be made as small as necessary to achieve the
current needed within the A2 output current-driving capability.
In this circuit, OP2177 delivers ±5 mA in both directions, and
the voltage compliance approaches 15 V. It can be shown that
the output impedance is
)(
)(
R2BR2AR1'R1R2'
R2AR1R2BR1'
Z
O
+
+
=
(9)
ZO can be infinite if resistors R1 and R2 match precisely with R1
and R2A + R2B, respectively. On the other hand, ZO can be
negative if the resistors are not matched. As a result, C1, in the
range of 1 pF to 10 pF, is needed to prevent oscillation from the
negative impedance.
RESISTANCE SCALING
The AD5231 offers 10 kΩ, 50 kΩ, and 100 kΩ nominal
resistance. For users who need lower resistance but want to
maintain the number of adjustment steps, they can parallel
multiple devices. For example, Figure 54 shows a simple scheme
of paralleling two AD5231s. To adjust half the resistance
linearly per step, users need to program both devices coherently
with the same settings and tie the terminals as shown.
A1
B1 W1 W2
A2
B2
LD
02739-053
Figure 54. Reduce Resistance by Half with Linear Adjustment Characteristics
In voltage diver mode, by paralleling a discrete resistor as
shown in Figure 55, a proportionately lower voltage appears at
Terminals AB. This translates into a finer degree of precision,
because the step size at Terminal W is smaller. The voltage can
be found as follows:
DD
AB
AB
WV
D
R2RR3
)R2R
DV ××
+
=1024//
//(
)(
(10)
R1
R2 A
BW
R3
02739-059
Figure 55. Lowering the Nominal Resistance
Figure 54 and Figure 55 show that the digital potentiometers
change steps linearly. On the other hand, pseudo log taper
adjustment is usually preferred in applications such as audio
control. Figure 56 shows another type of resistance scaling. In
this configuration, the smaller the R2 with respect to R1, the
more the pseudo log taper characteristic of the circuit behaves.
R1 R2
V
O
A
BW
02739-055
Figure 56. Resistor Scaling with Pseudo Log Adjustment Characteristics
AD5231 Data Sheet
Rev. D | Page 26 of 28
RDAC CIRCUIT SIMULATION MODEL
The internal parasitic capacitances and the external load
dominates the ac characteristics of the RDACs. The −3 dB
bandwidth of the AD5231BRU10 (10 kΩ resistor) measures
370 kHz at half scale when configured as a potentiometer
divider. Figure 15 provides the large signal BODE plot charac-
teristics. A parasitic simulation mode is shown in Figure 57.
A
RDAC
10kΩ
W
B
C
A
50pF C
B
50pF
C
W
50pF
02739-056
Figure 57. RDAC Circuit Simulation Model for RDAC = 10 kΩ
The following code provides a macro model net list for the
10 k RDAC:
.PARAM D = 1024, RDAC = 10E3
*
.SUBCKT DPOT (A, W, B)
*
CA A 0 50E-12
RWA A W {(1-D/1024)* RDAC + 15}
CW W 0 50E-12
RWB W B {D/1024 * RDAC + 15}
CB B 0 50E-12
*
.ENDS DPOT
Data Sheet AD5231
Rev. D | Page 27 of 28
OUTLINE DIMENSIONS
16 9
81
PI N 1
SEATING
PLANE
4.50
4.40
4.30
6.40
BSC
5.10
5.00
4.90
0.65
BSC
0.15
0.05
1.20
MAX 0.20
0.09 0.75
0.60
0.45
0.30
0.19
COPLANARITY
0.10
COM P LIANT T O JEDE C S TANDARDS M O-153-AB
Figure 58. 16-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-16)
Dimensions shown in millimeters
ORDERING GUIDE
Model1 RAB (kΩ) Temperature Range Package Description Package Option Ordering Quantity
AD5231BRU10 10 40°C to +85°C 16-Lead TSSOP RU-16 96
AD5231BRU10-REEL7 10 40°C to +85°C 16-Lead TSSOP RU-16 1,000
AD5231BRUZ10 10 40°C to +85°C 16-Lead TSSOP RU-16 96
AD5231BRUZ10-REEL7 10 40°C to +85°C 16-Lead TSSOP RU-16 1,000
AD5231BRUZ50 50 40°C to +85°C 16-Lead TSSOP RU-16 96
AD5231BRUZ50-REEL7 50 40°C to +85°C 16-Lead TSSOP RU-16 1,000
AD5231BRU100 100 40°C to +85°C 16-Lead TSSOP RU-16 96
AD5231BRU100-REEL7 100 40°C to +85°C 16-Lead TSSOP RU-16 1,000
AD5231BRUZ100 100 40°C to +85°C 16-Lead TSSOP RU-16 96
AD5231BRUZ100-RL7 100 40°C to +85°C 16-Lead TSSOP RU-16 1,000
1 Z = RoHS Compliant Part.
AD5231 Data Sheet
Rev. D | Page 28 of 28
NOTES
Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I2C Patent
Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
©2001–2013 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D02739-0-3/13(D)