SN54ACT563, SN74ACT563 OCTAL D-TYPE TRANSPARENT LATCHES WITH 3-STATE OUTPUTS SCAS550A - NOVEMBER 1995 - REVISED 1996 D D D SN54ACT563 . . . J OR W PACKAGE SN74ACT563 . . . DB, DW, N, OR PW PACKAGE (TOP VIEW) Inputs Are TTL-Voltage Compatible 3-State Inverted Outputs Drive Bus Lines Directly Flow-Through Architecture to Optimize PCB Layout EPIC (Enhanced-Performance Implanted CMOS) 1-m Process Package Options Include Plastic Small-Outline (DW), Shrink Small-Outline (DB), Thin Shrink Small-Outline (PW), Ceramic Chip Carriers (FK) and Flatpacks (W), and Standard Plastic (N) and Ceramic (J) DIPs OE 1D 2D 3D 4D 5D 6D 7D 8D GND description 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VCC 1Q 2Q 3Q 4Q 5Q 6Q 7Q 8Q LE SN54ACT563 . . . FK PACKAGE (TOP VIEW) 2D 1D OE VCC The 'ACT563 are octal D-type transparent latches with 3-state outputs. When the latch-enable (LE) input is high, the Q outputs are set to the complements of the data (D) inputs. When LE is taken low, the Q outputs are latched at the inverse logic levels set up at the D inputs. 3D 4D 5D 6D 7D 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 2Q 3Q 4Q 5Q 6Q 8D GND CLK 8Q 7Q A buffered output-enable (OE) input places the eight outputs in either a normal logic state (high or low logic levels) or the high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and increased high logic level provide the capability to drive bus lines without interface or pullup components. 1Q D D OE does not affect internal operations of the latches. Old data can be retained or new data can be entered while the outputs are in the high-impedance state. The SN54ACT563 is characterized for operation over the full military temperature range of - 55C to 125C. The SN74ACT563 is characterized for operation from -40C to 85C. FUNCTION TABLE (each latch) INPUTS OUTPUT Q OE LE D L H H L L H L H L L X Q0 H X X Z Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. EPIC is a trademark of Texas Instruments Incorporated. Copyright 1996, Texas Instruments Incorporated UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SN54ACT563, SN74ACT563 OCTAL D-TYPE TRANSPARENT LATCHES WITH 3-STATE OUTPUTS SCAS550A - NOVEMBER 1995 - REVISED 1996 logic symbol OE LE 1D 2D 3D 4D 5D 6D 7D 8D 1 11 2 logic diagram (positive logic) EN OE C1 1D 1 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 LE 1 11 1Q C1 2Q 3Q 1D 2 19 1Q 1D 4Q 5Q 6Q To Seven Other Channels 7Q 8Q This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to VCC + 0.5 V Output voltage range, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0 or VI > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA Output clamp current, IOK (VO < 0 or VO > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mA Maximum power dissipation at TA = 55C (in still air) (see Note 2): DB package . . . . . . . . . . . . . . . . . 0.6 W DW package . . . . . . . . . . . . . . . . . 1.6 W N package . . . . . . . . . . . . . . . . . . . 1.3 W PW package . . . . . . . . . . . . . . . . . 0.7 W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The maximum package power dissipation is calculated using a junction temperature of 150C and a board trace length of 750 mils, except for the N package, which has a trace length of zero. 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN54ACT563, SN74ACT563 OCTAL D-TYPE TRANSPARENT LATCHES WITH 3-STATE OUTPUTS SCAS550A - NOVEMBER 1995 - REVISED 1996 recommended operating conditions (see Note 3) SN54ACT563 MAX MIN MAX 4.5 5.5 4.5 5.5 VCC VIH Supply voltage VIL VI Low-level input voltage Input voltage 0 VO IOH Output voltage 0 High-level output current IOL t/v Low-level output current High-level input voltage SN74ACT563 MIN 2 2 0.8 Input transition rise or fall rate TA Operating free-air temperature NOTE 3: Unused inputs must be held high or low to prevent them from floating. -55 UNIT V V 0.8 V VCC VCC V -24 -24 mA 24 24 mA 8 8 ns/V 85 C VCC VCC 125 0 0 -40 V electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS IOH = -50 50 A VOH IOH = -24 24 mA IOH = -50 mA IOH = -75 mA TA = 25C MIN TYP MAX SN54ACT563 MIN MAX 4.4 4.49 4.4 4.4 5.4 5.49 5.4 5.4 4.5 V 3.86 3.7 3.76 5.5 V 4.86 4.7 4.76 MAX V 3.85 4.5 V 0.001 5.5 V 0.001 0.1 0.1 0.1 0.1 0.1 0.1 4.5 V 0.36 0.5 0.44 5.5 V 0.36 0.5 0.44 5.5 V IOZ II VO = VCC or GND VI = VCC or GND 5.5 V 0.25 5.5 V 0.1 ICC VI = VCC or GND, IO = 0 One input at 3.4 V, Other inputs at GND or VCC 5.5 V 4 1.6 V 1.65 5.5 V 5.5 V UNIT 3.85 IOL = 50 mA IOL = 75 mA ICC MIN 5.5 V 5.5 V IOL = 24 mA SN74ACT563 4.5 V 5.5 V IOL = 50 A VOL VCC 1.65 5 0.6 2.5 A 1 1 A 80 40 A 1.5 mA Ci VI = VCC or GND 5V 4.5 Not more than one output should be tested at a time, and the duration of the test should not exceed 2 ms. This is the increase in supply current for each input that is at one of the specified TTL voltage levels rather than 0 V or VCC. pF timing requirements over recommended operating free-air temperature range, VCC = 5 V 0.5 V (unless otherwise noted) (see Figure 1) TA = 25C MIN MAX SN54ACT563 MIN MAX SN74ACT563 MIN MAX UNIT tw tsu Pulse duration, LE high 3 5 3 ns Setup time, data before LE 4 4.5 4.5 ns th Hold time, data after LE 0 1.5 0 ns PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 SN54ACT563, SN74ACT563 OCTAL D-TYPE TRANSPARENT LATCHES WITH 3-STATE OUTPUTS SCAS550A - NOVEMBER 1995 - REVISED 1996 switching characteristics over recommended operating VCC = 5 V 0.5 V (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL D Q tPLH tPHL LE Q tPZH tPZL OE Q tPHZ tPLZ OE Q MIN free-air TA = 25C TYP MAX temperature SN54ACT563 SN74ACT563 MIN MAX MIN MAX 3 7 11.5 1 14.5 2.5 12.5 3 6 10 1 12 2.5 11 3 6.5 10.5 1 12.5 2.5 11.5 2.5 5.5 9.5 1 11.5 2 10.5 2.5 5.5 9 1 11.5 2 10 2 5.5 8.5 1 11 2 9.5 3.5 6.5 10.5 1 12 2.5 11.5 2 4.5 8 1 9.5 1 8.5 range, UNIT ns ns ns ns operating characteristics, VCC = 5 V, TA = 25C PARAMETER Cpd TEST CONDITIONS Power dissipation capacitance CL = 50 pF, f = 1 MHz PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. 4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TYP 50 UNIT pF SN54ACT563, SN74ACT563 OCTAL D-TYPE TRANSPARENT LATCHES WITH 3-STATE OUTPUTS SCAS550A - NOVEMBER 1995 - REVISED 1996 PARAMETER MEASUREMENT INFORMATION 2 x VCC S1 500 From Output Under Test Open 500 CL = 50 pF (see Note A) TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 2 x VCC Open LOAD CIRCUIT 3V Timing Input 1.5 V 0V tw tsu 3V 1.5 V Input th 1.5 V 3V 1.5 V Data Input 1.5 V 0V 0V VOLTAGE WAVEFORMS VOLTAGE WAVEFORMS Output Control (low-level enabling) 3V Input 1.5 V 1.5 V 0V Output 50% VCC VOH 50% VCC VOL Output Waveform 2 S1 at Open (see Note B) 1.5 V 0V tPZL [ VCC tPLZ Output Waveform 1 S1 at 2 x VCC (see Note B) tPHL tPLH 3V 1.5 V 50% VCC VOL + 0.3 V VOL tPHZ tPZH 50% VCC VOH - 0.3 V VOH [0V VOLTAGE WAVEFORMS VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR 1 MHz, ZO = 50 , tr 2.5 ns, tf 2.5 ns. D. The outputs are measured one at a time with one input transition per measurement. Figure 1. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI's publication of information regarding any third party's products or services does not constitute TI's approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated