SPEC NO: DSAK2442 REV NO: V.4A DATE: MAR/02/2013 PAGE: 1 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005917
2.8X0.8mm RIGHT ANGLE SMD CHIP LED
LAMP
Part Number: AA2810ASES/J3 Hyper Red
Features
z2.8mmX0.8mm right angle SMT LED, 1.2mm thickness.
zLow power consumption.
zIdeal for backlight and indicator.
zVarious colors and lens types available.
zPackage : 2000pcs / reel.
zMoisture sensitivity level : level 3.
zRoHS compliant.
Description
The Hyper Red device is based on light emitting diode chip
made from AlGaInP.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.1(0.0039") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAK2442 REV NO: V.4A DATE: MAR/02/2013 PAGE: 2 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005917
Handling Precautions
Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic
significantly reduces thermal stress, it is more susceptible to damage by external mechanical force.
As a result, special handling precautions need to be observed during assembly using silicone encapsulated
LED products. Failure to comply might lead to damage and premature failure of the LED.
1. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry.
2. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of
leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances.
All design applications should refer to Kingbright application notes available at
http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAK2442 REV NO: V.4A DATE: MAR/02/2013 PAGE: 3 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005917
Selection Guide
Absolute Maximum Ratings at TA=25°C
Electrical / Optical Characteristics at TA=25°C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
Part No. Dice Lens Type
Iv (mcd) [2]
@ 20mA
V
iewing
Angle [1]
Min. Typ. 2θ1/2
AA2810ASES/J3 Hyper Red (AlGaInP) Water Clear
1300 1800
*400 *550
110°
Symbol Parameter Device Typ. Max. Units Test Conditions
λpeak Peak Wavelength Hyper Red 640 nm IF=20mA
λD [1] Dominant Wavelength Hyper Red 625 nm IF=20mA
Δλ1/2 Spectral Line Half-width Hyper Red 25 nm IF=20mA
C Capacitance Hyper Red 27 pF VF=0V;f=1MHz
VF [2] Forward Voltage Hyper Red 2.2 2.8 V IF=20mA
IR Reverse Current Hyper Red 10 uA VR=5V
Parameter Hyper Red Units
Power dissipation 84 mW
DC Forward Current 30 mA
Peak Forward Current [1] 150 mA
Reverse Voltage 5 V
Operating Temperature -40°C To +85°C
Storage Temperature -40°C To +85°C
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
* Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Notes:
1.Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
3. Wavelength value is traceable to the CIE127-2007 compliant national standards.
SPEC NO: DSAK2442 REV NO: V.4A DATE: MAR/02/2013 PAGE: 4 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005917
Hyper Red AA2810ASES/J3
SPEC NO: DSAK2442 REV NO: V.4A DATE: MAR/02/2013 PAGE: 5 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005917
AA2810ASES/J3
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAK2442 REV NO: V.4A DATE: MAR/02/2013 PAGE: 6 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005917
PACKING & LABEL SPECIFICATIONS AA2810ASES/J3
