Two-chip SLIC Protector Modified TO-220 RoHS This two-chip SLIC modified TO-220 unidirectional protector is constructed with a 1 (T) 2 (G) 3 (R) SIDACtor(R) device and an integrated diode. It protects SLICs (Subscriber Line Interface Circuits) from damage during transient voltage activity and enables line cards to comply with various regulatory requirements including GR 1089, ITU K.20, K.21 and K.45, IEC 60950, UL 60950, and TIA-968-A (formerly known as FCC Part 68). For details of specific design criteria, see Figure 6.40 through Figure 6.43 in Section 6, "Reference Designs" of this Telecom Design Guide. Electrical Parameters VDRM Volts Part Number * VS Volts Pins 1-2, 3-2 VT Volts VF Volts IDRM Amps IS mAmps IT Amps IH mAmps 120 P0641A_2L 58 77 4 5 5 800 2.2 P0721A_2L 65 88 4 5 5 800 2.2 120 P0901A_2L 75 98 4 5 5 800 2.2 120 P1101A_2L 95 130 4 5 5 800 2.2 120 P1301A_2L 120 160 4 5 5 800 2.2 120 P1701A_2L 160 200 4 5 5 800 2.2 120 * "L" in part number indicates RoHS compliance. For non-RoHS compliant device, delete "L" from part number. For surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * VDRM is measured at IDRM. * VS and VF are measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Parallel capacitive loads may affect electrical parameters. * Compliance with GR 1089 or UL 60950 power fault tests may require special design considerations. Contact the factory for further information. Surge Ratings in Amps Series IPP 0.2x310 * 2x10 * 8x20 * 0.5x700 ** 2x10 ** 1.2x50 ** 10x160 * 10x160 ** 10x560 * 10x560 ** 5x320 * 9x720 ** Amps Amps Amps 10x360 * 10x1000 * 5x310 * ITSM 10x360 ** 10x1000 ** 10x700 ** 50 / 60 Hz Amps Amps Amps Amps A 20 150 150 90 50 75 75 C 50 500 400 200 150 200 175 Amps di/dt Amps Amps Amps/s 45 75 20 500 100 200 50 500 * Current waveform in s ** Voltage waveform in s www.littelfuse.com 3 - 68 (c) 2006 Littelfuse * Telecom Design Guide Two-chip SLIC Protector Modified TO-220 Thermal Considerations Symbol Modified TO-220 Value Unit Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C 50 C/W RJA PIN 1 Parameter TJ Thermal Resistance: Junction to Ambient PIN 3 PIN 2 Capacitance Values pF Pin 1-2 / 3-2 (4-5 / 6-5) Tip-Ground, Ring-Ground pF Part Number MIN MAX MIN MAX P0641AA2L 40 200 20 105 P0641AC2L 40 200 20 105 P0721AA2L 35 190 20 105 P0721AC2L 35 190 20 105 P0901AA2L 30 180 20 105 P0901AC2L 30 180 20 105 P1101AA2L 25 160 15 105 P1101AC2L 25 160 15 105 P1301AA2L 25 160 15 105 P1301AC2L 25 160 15 105 P1701AA2L 25 125 15 105 P1701AC2L 25 125 15 105 Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Telecom Design Guide * (c) 2006 Littelfuse 3 - 69 www.littelfuse.com SIDACtor Devices Package Two-chip SLIC Protector Modified TO-220 IPP - Peak Pulse Current - %IPP +I VF VS VDRM VT -V IDRM +V IH IS Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 IT 0 tr td t - Time (s) -I 14 12 10 IH 8 6 25 C 4 2 IH (TC = 25 C) tr x td Pulse Waveform Ratio of Percent of VS Change - % V-I Characteristics 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature www.littelfuse.com Normalized DC Holding Current versus Case Temperature 3 - 70 (c) 2006 Littelfuse * Telecom Design Guide