3MTM Moisture Barrier Bag Dri-Shield 2000 Product Data Sheet Product Data Sheet 3MTM Static Shielding Bag 1900 and 1910 This transparent metal-in static shielding bag is designed to provide a static safe environment for sensitive electronic devices. Bags are printed with an ESD warning symbol and a lot code for traceability. Open top (1900) and ZipTop (1910) styles are available. The bags are heat sealable. 3M Static Shielding Bags 1900 are manufactured from a polyester, metal, polyethylene laminate. The polyester dielectric in concert with the metal layer is intended to provide shielding of Electrostatic Discharge (ESD) and to help minimize the penetration of electric field. These bags are tested to meet or exceed certain electrical and physical requirements of Static Shielding Bags, ANSI/ESD S541, and to be ANSI/ESD S20.20 program compliant. Bags are RoHS Compliant* and lead-free**. 3MTM Static Shielding Bag 1900 and 1910 Physical Typical Value Testing Method Tensile Strength 5100 PSI, 35 MPa ASTM D882 Puncture Resistance 12 lbs, 53 N MIL-STD-3010C Method 2065 Seal Strength 9 lbs, 40 N ASTM D882 Thickness 2.8 mils, .071 mm +/-15% MIL-STD-3010C Method 1003 Marking Adhesion Pass IPC-TM-650 2.4.1 Transparency 40% Tobias Electrical Typical Value Testing Method ESD Shielding <10 nJ ANSI/ESD STM11.31 Surface Resistance Interior <1x1011 ohms ANSI/ESD STM11.11 Surface Resistance Exterior <1x1011 ohms ANSI/ESD STM11.11 Static Decay < 2 seconds ETS 406D Cleanliness Typical Value Testing Method Silicone Not Detected FTIR Heat Sealing Conditions Typical Value Temperature 375F, 190C Time 0.5 - 3.5 seconds Pressure 30 - 70 PSI, 206 - 482 KPa This product is intended for commercial use only. This product is not on the Qualified Product Listing under the Defense Standardization Program. 3MTM Moisture Barrier Bag Dri-Shield 2000 Product Data Sheet Product Data Sheet OpenOpen Top Top BagBag 3M Static Shielding Bag 1900 and 1910 TM ZipTop BagBag ZipTop 3MTM Static Shielding Bags, Open Top 1900 Dimensions (W x L in.) Part No. Dimensions (W x L in.) Part No. Dimensions (W x L in.) Part No. 3x5 19035 7 x 15 190715 12 x 16 1901216 4x4 19044 8x 8 19088 12 x 18 1901218 4x6 19046 8 x 10 190810 14 x 18 1901418 5x8 19058 8 x 12 190812 15 x 18 1901518 6x8 19068 10 x 12 1901012 16 x 24 1901624 6 x 10 190610 10 x 14 1901014 18 x 18 1901818 11 x 15 1901115 18 x 24 1901824 Custom Sizes Available 3MTM Static Shielding Bags, ZipTop 1910 Dimensions (W x L in.) Part No. Dimensions (W x L in.) Part No. Dimensions (W x L in.) Part No. 3x5 19135 6 x 10 191610 11 x 15 1911115 4x6 19146 8x8 191810 12 x 16 1911216 5x8 19158 8 x 12 191812 12 x 18 1911218 6x8 19168 10 x 12 1911012 18 x 18 1911818 Custom Sizes Available 3M is a trademark of 3M Company. All other trademarks are owned by their respective companies. * RoHS 2011/65/EU Compliant means that the product or part does not contain any of the substances in excess of the maximum concentration values ("MCVs") in EU RoHS Directive 2011/65/EU. The MCVs are by weight in homogeneous materials. This information represents 3M's knowledge and belief, which may be based in whole or in part on information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty section. **Lead-free means that the product has less than 2 ppm of lead when tested by ICP-AES, with reference to EPA method 3051A/3052. Tolerance (inches): Width -0, +0.250 Length +/- 0.125 Offset 0 to 0.250 widthsizes +/- for 0.125 *Seal Standard prompt shipment (usually same day). * Width is measured from inside seam to inside seam. * Length is measured from the top edge to the bottom fold. * Opening is in the "width" dimension. * Custom bag sizes are available. Important Notice All statements, technical information, and recommendations related to 3M's products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M's current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for one year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M's option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. 3 Electronic Solutions Division Static Control Products 926 JR Industrial Drive Sanford, NC 27332-9733 Toll-Free: 866-722-3736 International: 919-718-0000 Email: 3mstaticinfo@mmm.com www.3Mstatic.com Tolerance (inches): Width -0, +0.250 Length +/- 0.125 Offset 0 to 0.250 Seal width +/- 0.125 Please recycle. Printed in USA. (c) 3M 2013. All rights reserved. 98-0799-1128-9 JHA