© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 9/20/2013 1
One world. One KEMET
Benets
• AEC–Q200automotivequalied
• -55°C to +125°C operating temperature range
• Pb-FreeandRoHSCompliant
• Temperaturestabledielectric
• EIA0402,0603,0805,1206,1210,1812,and2220,casesizes
• DC voltage ratings of 6.3 V, 10 V, 16 V, 25 V, 50 V, 100 V,
200V,and250V
• Capacitanceofferingsrangingfrom10pFto22μF
• Availablecapacitancetolerancesof±5%,±10%,and±20%
• Non-polardevice,minimizinginstallationconcerns
• 100%puremattetin-platedterminationnishallowingfor
excellentsolderability
Applications
Typicalapplicationsincludedecoupling,bypass,lteringand
transient voltage suppression.
Overview
KEMET’sAutomotiveGradeSeriessurfacemountcapacitorsin
X7Rdielectricaresuitedforavarietyofapplicationsrequiring
proven,reliableperformanceinharshenvironments.Whether
under-hoodorin-cabin,thesedevicesemphasizethevitaland
robustnatureofcapacitorsrequiredformissionandsafetycritical
automotivecircuits.Strictertestingprotocolandinspection
criteriahavebeenestablishedforautomotivegradeproducts
inrecognitionofpotentiallyharshenvironmentalconditions.
KEMETautomotivegradeseriescapacitorsmeetthedemanding
AutomotiveElectronicsCouncil'sAEC–Q200qualication
requirements
X7Rdielectricfeaturesa125°Cmaximumoperatingtemperature
andisconsidered“temperaturestable,”TheElectronicsIndustries
Alliance(EIA)characterizesX7RdielectricasaClassIImaterial.
Componentsofthisclassicationarexed,ceramicdielectric
capacitorssuitedforbypassanddecouplingapplicationsor
forfrequencydiscriminatingcircuitswhereQandstabilityof
capacitancecharacteristicsarenotcritical.X7Rexhibitsa
predictablechangeincapacitancewithrespecttotimeandvoltage
andboastsaminimalchangeincapacitancewithreferenceto
ambienttemperature.Capacitancechangeislimitedto±15%from
-55°C to +125°C.
SurfaceMountMultilayerCeramicChipCapacitors(SMDMLCCs)
X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Ordering Information
C0805 C225 M 4 R A CAUTO
Ceramic
CaseSize
(L"xW")
Specication/
Series
Capacitance
Code(pF)
Capacitance
Tolerance Voltage Dielectric
Failure Rate/
Design TerminationFinish1
Packaging/Grade
(C-Spec)3
0402
0603
0805
1206
1210
1812
2220
C=Standard
2SignicantDigits
+ Number of Zeros
J = ±5%
K = ±10%
M = ±20%
9 = 6.3 V
8 = 10 V
4 = 16 V
3 = 25 V
5 = 50 V
1 = 100 V
2 = 200 V
A = 250 V
R = X7R A = N/A C = 100% Matte Sn AUTO = Automotive
Grade7"Reel
Unmarked
1 Additional termination nish options may be available. Contact KEMET for details
2 Additional reeling or packaging options may be available. Contact KEMET for details.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 9/20/2013 2
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Dimensions – Millimeters (Inches)
Ceramic Surface Mount
WL
TB
S
100% Tin or SnPb Plate
Nickel Plate
Conductive Metalization
Electrodes
EIA
Size
Code
Size
L
Length
W
Width
T
Thickness
B
Bandwidth
S
Separation
Minimum
Mounting
Technique
0402 1005 1.00 (.040) ± 0.05 (.002) 0.50 (.020) ± 0.05 (.002)
See Table 2 for
Thickness
0.30 (.012) ± 0.10 (.004) 0.30 (.012) SolderReowOnly
0603 1608 1.60 (.063) ± 0.15 (.006) 0.80 (.032) ± 0.15 (.006) 0.35 (.014) ± 0.15 (.006) 0.70 (.028)
SolderWaveor
SolderReow
0805 2012 2.00 (.079) ± 0.20 (.008) 1.25 (.049) ± 0.20 (.008) 0.50 (0.02) ± 0.25 (.010) 0.75 (.030)
1206 3216 3.20 (.126) ± 0.20 (.008) 1.60 (.063) ± 0.20 (.008) 0.50 (0.02) ± 0.25 (.010)
N/A
121013225 3.20 (.126) ± 0.20 (.008) 2.50 (.098) ± 0.20 (.008) 0.50 (0.02) ± 0.25 (.010)
SolderReowOnly1812 4532 4.50 (.177) ± 0.30 (.012) 3.20 (.126) ± 0.30 (.012) 0.60 (.024) ± 0.35 (.014)
2220 5650 5.70 (.224) ± 0.40 (.016) 5.00 (.197) ± 0.40 (.016) 0.60 (.024) ± 0.35 (.014)
1 For capacitance values ≥ 12 µF add 0.02 (0.001) to the width tolerance dimension
Qualication/Certication
AutomotiveGradeproductsmeetorexceedtherequirementsoutlinedbytheAutomotiveElectronicsCouncil.Detailsregardingtest
methodsandconditionsarereferencedindocumentAEC–Q200,StressTestQualicationforPassiveComponents.Foradditional
informationregardingtheAutomotiveElectronicsCouncilandAEC–Q200,pleasevisittheirwebsiteatwww.aecouncil.com.
Environmental Compliance
Pb-FreeandRoHSCompliant.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 9/20/2013 3
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Electrical Parameters/Characteristics
Item Parameters/Characteristics
Operating Temperature Range -55°C to +125°C
CapacitanceChangewithReferenceto+25°Cand0VDCApplied(TCC) ±15%
AgingRate(Maximum%CapacitanceLoss/DecadeHour) 3.0%
DielectricWithstandingVoltage(DWV)
250%ofratedvoltage
(5±1secondsandcharge/dischargenotexceeding50mA)
DissipationFactor(DF)MaximumLimit@25ºC 5%(6.3and10V),3.5%(16and25V)and2.5%(50to250V)
InsulationResistance(IR)Limit@25°C
SeeInsulationResistanceLimitTable
(Ratedvoltageappliedfor120±5seconds@25°C)
Regarding aging rate: Capacitance measurements (including tolerance) are indexed to a referee time of 1,000 hours.
To obtain IR limit, divide MΩ-µF value by the capacitance and compare to GΩ limit. Select the lower of the two limits.
Capacitance and dissipation factor (DF) measured under the following conditions:
1 kHz ±50 Hz and 1.0 ±0.2 Vrms if capacitance ≤ 10 µF
120 Hz ±10 Hz and 0.5 ±0.1 Vrms if capacitance >10 µF
Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 and Agilent E4980 have a feature known as
Automatic Level Control (ALC). The ALC feature should be switched to "ON."
Post Environmental Limits
High Temperature Life, Biased Humidity, Moisture Resistance
Dielectric RatedDC
Voltage
Capacitance
Value
Dissipation Factor
(Maximum %)
Capacitance
Shift
Insulation
Resistance
X7R
> 25
All
3.0
±20% 10%ofInitialLimit16/25 5.0
< 16 7.5
Insulation Resistance Limit Table
EIA Case Size
1,000 Megohm
Microfarads or 100 GΩ
500 Megohm
Microfarads or 10 GΩ
0201
N/A
ALL
0402
< 0.012 µF
≥0.012µF
0603
< 0.047 µF
≥0.047µF
0805
< 0.047 µF
≥0.047µF
1206
< 0.22 µF
≥0.22µF
1210
< 0.39 µF
≥0.39µF
1808
ALL
N/A
1812
< 2.2 µF
≥2.2µF
1825
ALL
N/A
2220
< 10 µF
≥10µF
2225
ALL
N/A
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 9/20/2013 4
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Capacitance Cap
Code
Series C0402 C0603 C0805 C1206
Voltage Code 9843 5 98435129843512A 9 843512A
Voltage DC
6.3
10
16
25
50
6.3
10
16
25
50
100
200
6.3
10
16
25
50
100
200
250
6.3
10
16
25
50
100
200
250
Capacitance
Tolerance
Product Availability and Chip Thickness Codes – See Table 2 for Chip Thickness Dimensions
10-91 pF 100-910 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC EB EB EB EB EB EB EB
100 - 150 pF 101-151 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC EB EB EB EB EB EB EB
180 - 820 pF 181-820 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB
1,000 pF 102 J K M BB BB BB BB BB CB CB CB CB CF CB CF DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
1,200 pF 122 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
1,500 pF 152 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
1,800 pF 182 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
2,200 pF 222 J K M BB BB BB BB BB CB CB CB CB CF CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
2,700 pF 272 J K M BB BB BB BB BB CB CB CB CB CB CF CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
3,300 pF 332 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
3,900 pF 392 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
4,700 pF 472 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
5,600 pF 562 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
6,800 pF 682 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
8,200 pF 822 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
10,000 pF 103 J K M BB BB BB BB BB CB CB CB CB CF CF CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
12,000 pF 123 J K M BB BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
15,000 pF 153 J K M BB BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DD DC DC EB EB EB EB EB EB EB EB
18,000 pF 183 J K M BB BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DD DC DC EB EB EB EB EB EB EB EB
22,000 pF 223 J K M BB BB BB BB BB CB CB CB CB CF CF DC DC DC DC DC DD DC DC EB EB EB EB EB EB EB EB
27,000 pF 273 J K M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DD DE EB EB EB EB EB EB EB EB
33,000 pF 333 J K M BB BB BB BB CB CB CB CF CB CB DC DC DC DC DC DD DE EB EB EB EB EB EB EB EB
39,000 pF 393 J K M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DD DE EB EB EB EB EB EC EB EB
47,000 pF 473 J K M BB BB BB BB CB CB CB CB CF CB DC DC DC DC DC DE DG EB EB EB EB EB EC ED ED
56,000 pF 563 J K M BB BB BB CB CB CB CB CB DD DD DD DD DD DE DG EB EB EB EB EB EB ED ED
68,000 pF 683 J K M BB BB BB CB CB CB CB CF DD DD DD DD DD DE EB EB EB EB EB EB ED ED
82,000 pF 823 J K M BB BB BB CB CB CB CB CB DD DD DD DD DD DE EB EB EB EB EB EB ED ED
0.10 µF 104 J K M BB BB BB CB CB CF CF CF DC DC DC DC DC DE EB EB EB EB EB EB EM EM
0.12 µF 124 J K M CB CB CB CB CB DC DC DC DC DD DG EC EC EC EC EC EC EG
0.15 µF 154 J K M CB CB CB CB CB DC DC DC DC DD DG EC EC EC EC EC EC EG
0.18 µF 184 J K M CB CB CB CB DC DC DC DC DD DG EC EC EC EC EC EC
0.22 µF 224 J K M CB CB CB CB DC DC DC DC DD DG EC EC EC EC EC EC
0.27 µF 274 J K M CB CB CB DD DD DD DD DD EB EB EB EB EC EM
0.33 µF 334 J K M CB CB CB DD DD DD DD DD EB EB EB EB EC EG
0.39 µF 394 J K M CB CB CB DG DG DG DG DE EB EB EB EB EC EG
0.47 µF 474 J K M CB CB CB DD DD DD DD DE EC EC EC EC EC EG
0.56 µF 564 J K M DD DD DD DG DH ED ED ED ED EC
0.68 µF 684 J K M DD DD DD DG DH EE EE EE EE ED
0.82 µF 824 J K M DD DD DD DG EF EF EF EF ED
1.0 µF 105 J K M DD DD DD DG EF EF EF EG ED
1.2 µF 125 J K M DE DE DE ED ED ED EG EH
1.5 µF 155 J K M DG DG DG EF EF EF EG EH
1.8 µF 185 J K M DG DG DG ED ED ED EF EH
2.2 µF 225 J K M DG DG DG ED ED ED EF EH
2.7 µF 275 J K M EN EN EN EH
3.3 µF 335 J K M ED ED ED EH
3.9 µF 395 J K M EF EF EF EH
4.7 µF 475 J K M EF EF EF EH
5.6 µF 565 J K M EH EH EH
6.8 µF 685 J K M EH EH EH
8.2 µF 825 J K M EH EH EH
10 µF 106 J K M EH EH EH
Capacitance Cap
Code
Voltage DC
6.3
10
16
25
50
6.3
10
16
25
50
100
200
6.3
10
16
25
50
100
200
250
6.3
10
16
25
50
100
200
250
Voltage Code 9843 5 98435129843512A 9 843512A
Series
C0402
C0603
C0805
C1206
Table 1A – Capacitance Range/Selection Waterfall (0402 – 1206 Case Sizes)
Roll Over for
Order Info.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 9/20/2013 5
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Table 1B – Capacitance Range/Selection Waterfall (1210 – 2220 Case Sizes)
Capacitance Cap
Code
Series C1210 C1812 C1825 C2220
Voltage Code 9843512A3 5 12A512A3 5 12A
Voltage DC
6.3
10
16
25
50
100
200
250
25
50
100
200
250
50
100
200
250
25
50
100
200
250
Capacitance
Tolerance
Product Availability and Chip Thickness Codes – See Table 2 for Chip Thickness Dimensions
10 - 91 pF 100-910 J K M FB FB FB FB FB FB FB
100 - 390 pF 101-391 J K M FB FB FB FB FB FB FB
470 - 820 pF 471-821 J K M FB FB FB FB FB FB FB GB GB GB GB
1,000 pF 102 J K M FB FB FB FB FB FB FB GB GB GB GB
1,200 pF 122 J K M FB FB FB FB FB FB FB GB GB GB GB
1,500 pF 152 J K M FB FB FB FB FB FB FE GB GB GB GB
1,800 pF 182 J K M FB FB FB FB FB FB FE GB GB GB GB
2,200 pF 222 J K M FB FB FB FB FB FB FB FB GB GB GB GB
2,700 pF 272 J K M FB FB FB FB FB FB FB FB GB GB GB GB
3,300 pF 332 J K M FB FB FB FB FB FB FB FB GB GB GB GB
3,900 pF 392 J K M FB FB FB FB FB FB FB FB GB GB GB GB
4,700 pF 472 J K M FB FB FB FB FB FB FB FB GB GB GB GD
5,600 pF 562 J K M FB FB FB FB FB FB FB FB GB GB GB GH
6,800 pF 682 J K M FB FB FB FB FB FB FB FB GB GB GB GB GB JE JE JE
8,200 pF 822 J K M FB FB FB FB FB FB FB FB GB GB GB GB GB JE JE JE
10,000 pF 103 J K M FB FB FB FB FB FB FB FB GB GB GB GB GB JE JE JE
12,000 pF 123 J K M FB FB FB FB FB FB FB FB GB GB GB GB GB JE JE JE
15,000 pF 153 J K M FB FB FB FB FB FB FB FB GB GB GB GB GB JE JE JE
18,000 pF 183 J K M FB FB FB FB FB FB FB FB GB GB GB GB GB JE JE JE
22,000 pF 223 J K M FB FB FB FB FB FB FB FB GB GB GB GB GB HB HB HB HB JE JE JE
27,000 pF 273 J K M FB FB FB FB FB FB FB FB GB GB GB GB GB HB HB HB HB JE JE JE
33,000 pF 333 J K M FB FB FB FB FB FB FB FB GB GB GB GB GB HB HB HB HB JB JB JB
39,000 pF 393 J K M FB FB FB FB FB FB FB FB GB GB GB GB GB HB HB HB HB JB JB JB
47,000 pF 473 J K M FB FB FB FB FB FB FB FB GB GB GB GB GB HB HB HB HB JB JB JB
56,000 pF 563 J K M FB FB FB FB FB FB FC FC GB GB GB GB GB HB HB HB HB JB JB JB
68,000 pF 683 J K M FB FB FB FB FB FB FC FC GB GB GB GB GB HB HB HB HB JB JB JB
82,000 pF 823 J K M FB FB FB FB FB FC FF FF GB GB GB GB GB HB HB HB HB JB JB JC JC JC
0.10 µF 104 J K M FB FB FB FB FB FD FG FG GB GB GB GB GB HB HB HB HB JB JB JC JC JC
0.12 µF 124 J K M FB FB FB FB FB FD GB GB GB GB GB HB HB HB HB JB JB JC JC JC
0.15 µF 154 J K M FC FC FC FC FC FD GB GB GB GE GE HB HB HB HB JB JB JC JC JC
0.18 µF 184 J K M FC FC FC FC FC FD GB GB GB GG GG HB HB HB HB JB JB JC JC JC
0.22 µF 224 J K M FC FC FC FC FC FD GB GB GB GG GG HB HB HB HB JB JB JC JC JC
0.27 µF 274 J K M FC FC FC FC FC FD GB GB GG GG GG HB HB HB HB JC JC JC JC JC
0.33 µF 334 J K M FD FD FD FD FD FD GB GB GG GG GG HB HB HB HB JC JC JC JC JC
0.39 µF 394 J K M FD FD FD FD FD FD GB GB GG GG GG HD HD HD HD JC JC JC JC JC
0.47 µF 474 J K M FD FD FD FD FD FD GB GB GG GJ GJ HD HD HD HD JC JC JC JC JC
0.56 µF 564 J K M FD FD FD FD FD FF GC GC GG HD HD HD HD JC JD JD JD JD
0.68 µF 684 J K M FD FD FD FD FD FG GC GC GG HD HD HD HD JC JD JD JD JD
0.82 µF 824 J K M FF FF FF FF FF FL GE GE GG HF HF HF HF JC JF JF JF JF
1.0 µF 105 J K M FH FH FH FH FH FM GE GE GG HF HF HF HF JC JF JF JF JF
1.2 µF 125 J K M FH FH FH FH FG JC JC
1.5 µF 155 J K M FH FH FH FH FG JC JC
1.8 µF 185 J K M FH FH FH FH FG JD JD
2.2 µF 225 J K M FJ FJ FJ FJ FG GO GO JF JF
2.7 µF 275 J K M FE FE FE FG FH
3.3 µF 335 J K M FF FF FF FM FM
3.9 µF 395 J K M FG FG FG FG FK
4.7 µF 475 J K M FC FC FC FG FS GK GK JF JF
5.6 µF 565 J K M FF FF FF FH
6.8 µF 685 J K M FG FG FG FM
8.2 µF 825 J K M FH FH FH FK
10 µF 106 J K M FH FH FH FS GK JF JO
15 µF 156 J K M JO
22 µF 226 J K M FS FS JO
Capacitance Cap
Code
Voltage DC
6.3
10
16
25
50
100
200
250
25
50
100
200
250
50
100
200
250
25
50
100
200
250
Voltage Code 9843512A3 5 12A512A3 5 12A
Series
C1210
C1812
C1825
C2220
Roll Over for
Order Info.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 9/20/2013 6
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Table 2 – Chip Thickness/Packaging Quantities
Thickness
Code
Case
Size
Thickness ±
Range (mm)
Paper Quantity Plastic Quantity
7" Reel 13" Reel 7" Reel 13" Reel
BB
0402
0.50 ± 0.05
10,000
50,000
0
0
CB
0603
0.80 ± 0.07
4,000
10,000
0
0
CF
0603
0.80 ± 0.07
4,000
15,000
0
0
DC
0805
0.78 ± 0.10
4,000
10,000
0
0
DD
0805
0.90 ± 0.10
4,000
10,000
0
0
DE
0805
1.00 ± 0.10
0
0
2,500
10,000
DG
0805
1.25 ± 0.15
0
0
2,500
10,000
DH
0805
1.25 ± 0.20
0
0
2,500
10,000
EB
1206
0.78 ± 0.10
4,000
10,000
4,000
10,000
EC
1206
0.90 ± 0.10
0
0
4,000
10,000
EN
1206
0.95 ± 0.10
0
0
4,000
10,000
ED
1206
1.00 ± 0.10
0
0
2,500
10,000
EE
1206
1.10 ± 0.10
0
0
2,500
10,000
EF
1206
1.20 ± 0.15
0
0
2,500
10,000
EM
1206
1.25 ± 0.15
0
0
2,500
10,000
EG
1206
1.60 ± 0.15
0
0
2,000
8,000
EH
1206
1.60 ± 0.20
0
0
2,000
8,000
FB
1210
0.78 ± 0.10
0
0
4,000
10,000
FC
1210
0.90 ± 0.10
0
0
4,000
10,000
FD
1210
0.95 ± 0.10
0
0
4,000
10,000
FE
1210
1.00 ± 0.10
0
0
2,500
10,000
FF
1210
1.10 ± 0.10
0
0
2,500
10,000
FG
1210
1.25 ± 0.15
0
0
2,500
10,000
FL
1210
1.40 ± 0.15
0
0
2,000
8,000
FH
1210
1.55 ± 0.15
0
0
2,000
8,000
FM
1210
1.70 ± 0.20
0
0
2,000
8,000
FJ
1210
1.85 ± 0.20
0
0
2,000
8,000
FK
1210
2.10 ± 0.20
0
0
2,000
8,000
FS
1210
2.50 ± 0.30
0
0
1,000
4,000
NA
1706
0.90 ± 0.10
0
0
4,000
10,000
NC
1706
1.00 ± 0.15
0
0
4,000
10,000
LD
1808
0.90 ± 0.10
0
0
2,500
10,000
LF
1808
1.00 ± 0.15
0
0
2,500
10,000
GB
1812
1.00 ± 0.10
0
0
1,000
4,000
GC
1812
1.10 ± 0.10
0
0
1,000
4,000
GD
1812
1.25 ± 0.15
0
0
1,000
4,000
GE
1812
1.30 ± 0.10
0
0
1,000
4,000
GH
1812
1.40 ± 0.15
0
0
1,000
4,000
GG
1812
1.55 ± 0.10
0
0
1,000
4,000
GK
1812
1.60 ± 0.20
0
0
1,000
4,000
GJ
1812
1.70 ± 0.15
0
0
1,000
4,000
GO
1812
2.50 ± 0.20
0
0
500
2,000
HB
1825
1.10 ± 0.15
0
0
1,000
4,000
HD
1825
1.30 ± 0.15
0
0
1,000
4,000
HF
1825
1.50 ± 0.15
0
0
1,000
4,000
JB
2220
1.00 ± 0.15
0
0
1,000
4,000
JC
2220
1.10 ± 0.15
0
0
1,000
4,000
JD
2220
1.30 ± 0.15
0
0
1,000
4,000
JE
2220
1.40 ± 0.15
0
0
1,000
4,000
JF
2220
1.50 ± 0.15
0
0
1,000
4,000
JO
2220
2.40 ± 0.15
0
0
500
2,000
Thickness
Code
Case
Size
Thickness ±
Range (mm)
7" Reel 13" Reel 7" Reel 13" Reel
Paper Quantity Plastic Quantity
Package quantity based on nished chip thickness specications
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 9/20/2013 7
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Table 3 – Chip Capacitor Land Pattern Design Recommendations per IPC–7351
EIA
Size
Code
Metric
Size
Code
Density Level A:
Maximum (Most)
Land Protrusion (mm)
Density Level B:
Median (Nominal)
Land Protrusion (mm)
Density Level C:
Minimum (Least)
Land Protrusion (mm)
C
Y
X
V1
V2
C
Y
X
V1
V2
C
Y
X
V1
V2
0402 1005 0.50 0.72 0.72 2.20 1.20 0.45 0.62 0.62 1.90 1.00 0.40 0.52 0.52 1.60 0.80
0603 1608 0.90 1.15 1.10 4.00 2.10 0.80 0.95 1.00 3.10 1.50 0.60 0.75 0.90 2.40 1.20
0805 2012 1.00 1.35 1.55 4.40 2.60 0.90 1.15 1.45 3.50 2.00 0.75 0.95 1.35 2.80 1.70
1206 3216 1.60 1.35 1.90 5.60 2.90 1.50 1.15 1.80 4.70 2.30 1.40 0.95 1.70 4.00 2.00
1210 3225 1.60 1.35 2.80 5.65 3.80 1.50 1.15 2.70 4.70 3.20 1.40 0.95 2.60 4.00 2.90
121013225 1.50 1.60 2.90 5.60 3.90 1.40 1.40 2.80 4.70 3.30 1.30 1.20 2.70 4.00 3.00
1812 4532 2.15 1.60 3.60 6.90 4.60 2.05 1.40 3.50 6.00 4.00 1.95 1.20 3.40 5.30 3.70
2220 5650 2.75 1.70 5.50 8.20 6.50 2.65 1.50 5.40 7.30 5.90 2.55 1.30 5.30 6.60 5.60
1 Only for capacitance values ≥ 22 µF
Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reow solder
processes. KEMET only recommends wave soldering of EIA 0603, 0805, and 1206 case sizes.
Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reow solder processes.
Density Level C: For high component density product applications. Before adapting the minimum land pattern variations the user should perform qualication
testing based on the conditions outlined in IPC Standard 7351 (IPC–7351).
Soldering Process
RecommendedSolderingTechnique:
•SolderwaveorsolderreowforEIAcasesizes0603,0805,and1206
•AllotherEIAcasesizesarelimitedtosolderreowonly
RecommendedSolderingProle:
•KEMETrecommendsfollowingtheguidelinesoutlinedinIPC/JEDECJ–STD–020
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 9/20/2013 8
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Table 4 – Performance & Reliability: Test Methods and Conditions
Stress Reference Test or Inspection Method
TerminalStrength JIS–C–6429 Appendix1,Note:Forceof1.8kgfor60seconds.
BoardFlex JIS–C–6429
Appendix2,Note:Standardterminationsystem–2.0mm(minimum)forallexcept3mmforC0G.
Flexibleterminationsystem–3.0mm(minimum).
Solderability J–STD–002
Magnication50X.Conditions:
a)MethodB,4hours@155°C,dryheat@235°C
b)MethodB@215°Ccategory3
c)MethodD,category3@260°C
TemperatureCycling JESD22MethodJA–104 1,000Cycles(-55°Cto+125°C).Measurementat24hours+/-2hoursaftertestconclusion.
BiasedHumidity MIL–STD–202Method103
LoadHumidity:1,000hours85°C/85%RHandratedvoltage.Add100Kohmresistor.Measurement
at24hours+/-2hoursaftertestconclusion.
LowVoltHumidity:1,000hours85°C/85%RHand1.5V.Add100Kohmresistor.
Measurementat24hours+/-2hoursaftertestconclusion.
Moisture Resistance MIL–STD–202Method106
t=24hours/cycle.Steps7aand7bnotrequired.Unpowered.
Measurementat24hours+/-2hoursaftertestconclusion.
ThermalShock MIL–STD–202Method107
-55°C/+125°C.Note:Numberofcyclesrequired–300,maximumtransfertime–20seconds,dwell
time – 15 minutes. Air – Air.
HighTemperatureLife
MIL–STD–202Method108
/EIA–198
1,000hoursat125°C(85°CforX5R,Z5UandY5V)with2Xratedvoltageapplied.
StorageLife MIL–STD–202Method108 150°C,0VDCfor1,000hours.
Vibration MIL–STD–202Method204
5g'sfor20min.,12cycleseachof3orientations.Note:Use8"X5"PCB0.031"thick7secure
pointsononelongsideand2securepointsatcornersofoppositesides.Partsmountedwithin2"
fromanysecurepoint.Testfrom10–2,000Hz
MechanicalShock MIL–STD–202Method213 Figure1ofMethod213,ConditionF.
Resistance to Solvents MIL–STD–202Method215 Addaqueouswashchemical,OKEMCleanorequivalent.
Storage and Handling
Ceramicchipcapacitorsshouldbestoredinnormalworkingenvironments.Whilethechipsthemselvesarequiterobustinother
environments,solderabilitywillbedegradedbyexposuretohightemperatures,highhumidity,corrosiveatmospheres,andlongterm
storage.Inaddition,packagingmaterialswillbedegradedbyhightemperature–reelsmaysoftenorwarpandtapepeelforcemay
increase.KEMETrecommendsthatmaximumstoragetemperaturenotexceed40ºCandmaximumstoragehumiditynotexceed70%
relativehumidity.Temperatureuctuationsshouldbeminimizedtoavoidcondensationonthepartsandatmospheresshouldbefreeof
chlorineandsulfurbearingcompounds.Foroptimizedsolderabilitychipstockshouldbeusedpromptly,preferablywithin1.5yearsof
receipt.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 9/20/2013 9
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Construction
Reference Item Material
A
Termination
System
Finish 100% Matte Sn
BBarrierLayer Ni
CBase Metal Cu
DInnerElectrode Ni
EDielectric Material BaTiO
3
Note: Image is exaggerated in order to clearly identify all components of construction.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 9/20/2013 10
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Capacitor Marking (Optional):
Thesesurfacemountmultilayerceramiccapacitorsare
normallysuppliedunmarked.Ifrequired,theycanbemarked
as an extra cost option. Marking is available on most KEMET
devicesbutmustberequestedusingthecorrectordering
codeidentier(s).Ifthisoptionisrequested,twosidesofthe
ceramicbodywillbelasermarkedwitha“K”toidentifyKEMET,
followedbytwocharacters(perEIA–198-seetablebelow)to
identifythecapacitancevalue.EIA0603casesizedevicesare
limitedtothe“K”characteronly.
Lasermarkingoptionisnotavailableon:
• C0G,UltraStableX8RandY5Vdielectricdevices
• EIA0402casesizedevices
• EIA0603casesizedeviceswithFlexibleTerminationoption.
• KPSCommercialandAutomotiveGradestackeddevices.
Markingappearsinlegiblecontrast.Illustratedbelowisan
exampleofanMLCCwithlasermarkingof“KA8”,which
designatesaKEMETdevicewithratedcapacitanceof100µF.
Orientationofmarkingisvendoroptional.
_
KA8
Capacitance (pF) For Various Alpha/Numeral Identi ers
Alpha
Character
Numeral
9
0
1
2
3
4
5
6
7
8
Capacitance (pF)
A
0.1
1 0
10
100
1,000
10,000
100,000
1,000,000
10,000,000
100,000,000
B
0.11
1.1
11
110
1,10 0
11,000
110,000
1,100,000
11,000,000
110,000,000
C 0.12 1 2 12 120 1,200 12,000 120,000 1,200,000 12,000,000 120,000,000
D
0.13
1 3
13
130
1,300
13,000
130,000
1,300,000
13,000,000
130,000,000
E
0.15
1 5
15
150
1,500
15,000
150,000
1,500,000
15,000,000
150,000,000
F
0.16
1 6
16
160
1,600
16,000
160,000
1,600,000
16,000,000
160,000,000
G
0.18
1 8
18
180
1,800
18,000
180,000
1,800,000
18,000,000
180,000,000
H 0.2 2 0 20 200 2,000 20,000 200,000 2,000,000 20,000,000 200,000,000
J
0.22
2 2
22
220
2,200
22,000
220,000
2,200,000
22,000,000
220,000,000
K
0.24
2.4
24
240
2,400
24,000
240,000
2,400,000
24,000,000
240,000,000
L
0.27
2.7
27
270
2,700
27,000
270,000
2,700,000
27,000,000
270,000,000
M
0.3
3 0
30
300
3,000
30,000
300,000
3,000,000
30,000,000
300,000,000
N 0.33 3 3 33 330 3,300 33,000 330,000 3,300,000 33,000,000 330,000,000
P
0.36
3 6
36
360
3,600
36,000
360,000
3,600,000
36,000,000
360,000,000
Q
0.39
3 9
39
390
3,900
39,000
390,000
3,900,000
39,000,000
390,000,000
R
0.43
4 3
43
430
4,300
43,000
430,000
4,300,000
43,000,000
430,000,000
S
0.47
4.7
47
470
4,700
47,000
470,000
4,700,000
47,000,000
470,000,000
T 0.51 5.1 51 510 5,100 51,000 510,000 5,100,000 51,000,000 510,000,000
U
0.56
5 6
56
560
5,600
56,000
560,000
5,600,000
56,000,000
560,000,000
V
0.62
6 2
62
620
6,200
62,000
620,000
6,200,000
62,000,000
620,000,000
W
0.68
6 8
68
680
6,800
68,000
680,000
6,800,000
68,000,000
680,000,000
X
0.75
7 5
75
750
7,500
75,000
750,000
7,500,000
75,000,000
750,000,000
Y 0.82 8 2 82 820 8,200 82,000 820,000 8,200,000 82,000,000 820,000,000
Z
0.91
9.1
91
910
9,100
91,000
910,000
9,100,000
91,000,000
910,000,000
a
0.25
2 5
25
250
2,500
25,000
250,000
2,500,000
25,000,000
250,000,000
b
0.35
3 5
35
350
3,500
35,000
350,000
3,500,000
35,000,000
350,000,000
d
0.4
4 0
40
400
4,000
40,000
400,000
4,000,000
40,000,000
400,000,000
e 0.45 4 5 45 450 4,500 45,000 450,000 4,500,000 45,000,000 450,000,000
f
0.5
5 0
50
500
5,000
50,000
500,000
5,000,000
50,000,000
500,000,000
m
0.6
6 0
60
600
6,000
60,000
600,000
6,000,000
60,000,000
600,000,000
n
0.7
7 0
70
700
7,000
70,000
700,000
7,000,000
70,000,000
700,000,000
t
0.8
8 0
80
800
8,000
80,000
800,000
8,000,000
80,000,000
800,000,000
y 0.9 9 0 90 900 9,000 90,000 900,000 9,000,000 90,000,000 900,000,000
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 9/20/2013 11
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Tape & Reel Packaging Information
KEMEToffersmultilayerceramicchipcapacitorspackagedin8,12and16mmtapeon7"and13"reelsinaccordancewithEIA
Standard481.Thispackagingsystemiscompatiblewithalltape-fedautomaticpickandplacesystems.SeeTable2fordetailson
reelingquantitiesforcommercialchips.
8 mm, 12 mm
or 16 mm Carrier Tape
178 mm (7.00")
or
330 mm (13.00")
Anti-Static Reel
Embossed Plastic* or
Punched Paper Carrier.
Embossment or Punched Cavity
Anti-Static Cover Tape
(.10 mm (.004") Maximum Thickness)
Chip and KPS Orientation in Pocket
(except 1825 Commercial, and 1825 and 2225 Military)
*EIA 01005, 0201, 0402 and 0603 case sizes available on punched paper carrier only.
KEMET
®
Bar Code Label
Sprocket Holes
Table 5 – Carrier Tape Con guration – Embossed Plastic & Punched Paper (mm)
EIA Case Size Tape Size (W)* Pitch (P
1
)*
01005 – 0402 8 2
0603 – 1210 8 4
1805 – 1808 12 4
≥1812 12 8
KPS 1210 12 8
KPS 1812 & 2220 16 12
Array0508&0612 8 4
*Refer to Figures 1 & 2 for W and P1 carrier tape reference locations.
*Refer to Tables 6 & 7 for tolerance speci cations.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 9/20/2013 12
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Figure 1 – Embossed (Plastic) Carrier Tape Dimensions
Po
T
F
W
Center Lines of Cavity
Ao
Bo
User Direction of Unreeling
Cover Tape
Ko
B
1
is for tape feeder reference only,
including draft concentric about B
o.
T
2
ØD
1
ØDo
B
1
S
1
T
1
E
1
E
2
P
1
P
2
Embossment
For cavity size,
see Note 1 Table 4
[10 pitches cumulative
tolerance on tape ± 0.2 mm]
Table 6 – Embossed (Plastic) Carrier Tape Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
TapeSize D0
D
1
Minimum
Note 1
E1P0 P2
R Reference
Note 2
S
1
Minimum
Note 3
T
Maximum
T
1
Maximum
8 mm
1.5 +0.10/-0.0
(0.059 +0.004/-0.0)
1.0
(0.039)
1.75 ±0.10
(0.069 ±0.004)
4.0 ±0.10
(0.157 ±0.004)
2.0 ±0.05
(0.079 ±0.002)
25.0
(0.984)
0.600
(0.024)
0.600
(0.024)
0.100
(0.004)
12 mm 1.5
(0.059)
30
(1.181)
16 mm
Variable Dimensions — Millimeters (Inches)
TapeSize Pitch
B
1
Maximum
Note 4
E
2
Minimum
F P1
T
2
Maximum
W
Maximum
A0,B0 & K0
8 mm Single (4 mm)
4.35
(0.171)
6.25
(0.246)
3.5 ±0.05
(0.138 ±0.002)
4.0 ±0.10
(0.157 ±0.004)
2.5
(0.098)
8.3
(0.327)
Note 512 mm
Single (4 mm) &
Double (8 mm)
8.2
(0.323)
10.25
(0.404)
5.5 ±0.05
(0.217 ±0.002)
8.0 ±0.10
(0.315 ±0.004)
4.6
(0.181)
12.3
(0.484)
16 mm Triple (12 mm)
12.1
(0.476)
14.25
(0.561)
7.5 ±0.05
(0.138 ±0.002)
12.0 ±0.10
(0.157 ±0.004)
4.6
(0.181)
16.3
(0.642)
1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and
hole location shall be applied independent of each other.
2. The tape with or without components shall pass around R without damage (see Figure 6).
3. If S1 < 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481 paragraph 4.3 section b).
4. B1 dimension is a reference dimension for tape feeder clearance only.
5. The cavity de ned by A0, B0 and K0 shall surround the component with suf cient clearance that:
(a) the component does not protrude above the top surface of the carrier tape.
(b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
(c) rotation of the component is limited to 20° maximum for 8 and 12 mm tapes and 10° maximum for 16 mm tapes (see Figure 3).
(d) lateral movement of the component is restricted to 0.5 mm maximum for 8 and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see Figure 4).
(e) for KPS Series product, A0 and B0 are measured on a plane 0.3 mm above the bottom of the pocket.
(f) see Addendum in EIA Standard 481 for standards relating to more precise taping requirements.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 9/20/2013 13
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Figure 2 – Punched (Paper) Carrier Tape Dimensions
User Direction of Unreeling
Top Cover Tape
T
Center Lines of Cavity
P
1
ØDo Po
P
2
E
1
F
E
2
W
G
A
0
B
0
Cavity Size,
See
Note 1, Table 7
Bottom Cover Tape
T
1
T
1
Bottom Cover Tape
[10 pitches cumulative
tolerance on tape ± 0.2 mm]
Table 7 – Punched (Paper) Carrier Tape Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
TapeSize D0E1P0P2T1 Maximum G Minimum
R Reference
Note 2
8 mm 1.5 +0.10 -0.0
(0.059 +0.004 -0.0)
1.75 ±0.10
(0.069 ±0.004)
4.0 ±0.10
(0.157 ±0.004)
2.0 ±0.05
(0.079 ±0.002)
0.10
(0.004) Maximum
0.75
(0.030)
25
(0.984)
Variable Dimensions — Millimeters (Inches)
TapeSize Pitch E2 Minimum F P1 T Maximum WMaximum A0 B0
8 mm Half(2mm) 6.25
(0.246)
3.5 ±0.05
(0.138 ±0.002)
2.0 ±0.05
(0.079 ±0.002)
1.1
(0.098)
8.3
(0.327)
Note 1
8 mm Single (4 mm)
4.0 ±0.10
(0.157 ±0.004)
8.3
(0.327)
1. The cavity de ned by A0, B0 and T shall surround the component with suf cient clearance that:
a) the component does not protrude beyond either surface of the carrier tape.
b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
c) rotation of the component is limited to 20° maximum (see Figure 3).
d) lateral movement of the component is restricted to 0.5 mm maximum (see Figure 4).
e) see Addendum in EIA Standard 481 for standards relating to more precise taping requirements.
2. The tape with or without components shall pass around R without damage (see Figure 6).
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 9/20/2013 14
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Packaging Information Performance Notes
1. Cover Tape Break Force: 1.0 Kg minimum.
2. Cover Tape Peel Strength: Thetotalpeelstrengthofthecovertapefromthecarriertapeshallbe:
Tape Width Peel Strength
8 mm 0.1 to 1.0 Newton (10 to 100 gf)
12and16mm 0.1 to 1.3 Newton (10 to 130 gf)
Thedirectionofthepullshallbeoppositethedirectionofthecarriertapetravel.Thepullangleofthecarriertapeshallbe165°to180°
fromtheplaneofthecarriertape.Duringpeeling,thecarrierand/orcovertapeshallbepulledatavelocityof300±10mm/minute.
3. Labeling:Barcodelabeling(standardorcustom)shallbeonthesideofthereeloppositethesprocketholes.Refer to EIA
Standards 556 and 624.
Figure 3 – Maximum Component Rotation
Ao
Bo
°
T
°
s
Maximum Component Rotation
Top View
Maximum Component Rotation
Side View
Tape Maximum
Width (mm) Rotation (°
T)
8,12 20
16 – 200 10 Tape Maximum
Width (mm) Rotation ( °
S)
8,12 20
16 – 56 10
72 – 200 5
Typical Pocket Centerline
Typical Component Centerline
Figure 4 – Maximum Lateral Movement
0.5 mm maximum
0.5 mm maximum
8 mm & 12 mm Tape
1.0 mm maximum
1.0 mm maximum
16 mm Tape
Figure 5 – Bending Radius
RR
Bending
Radius
Embossed
Carrier
Punched
Carrier
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 9/20/2013 15
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Figure 6 – Reel Dimensions
AD(See Note)
Full Radius,
See Note
B(see Note)
Access Hole at
Slot Location
(Ø 40 mm minimum)
If present,
tape slot in core
for tape start:
2.5 mm minimum width x
10.0 mm minimum depth
W3(Includes
flange distortion
at outer edge)
W2(Measured at hub)
W1(Measured at hub)
C
(Arbor hole
diameter)
Note: Drive spokes optional; if used, dimensions B and D shall apply.
N
Table 8 – Reel Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
TapeSize A B Minimum CD Minimum
8 mm 178 ±0.20
(7.008 ±0.008)
or
330 ±0.20
(13.000 ±0.008)
1.5
(0.059)
13.0 +0.5/-0.2
(0.521 +0.02/-0.008)
20.2
(0.795)
12 mm
16 mm
Variable Dimensions — Millimeters (Inches)
TapeSize N Minimum W
1
W
2
Maximum W
3
8 mm
50
(1.969)
8.4 +1.5/-0.0
(0.331 +0.059/-0.0)
14.4
(0.567)
Shallaccommodatetapewidth
withoutinterference
12 mm
12.4 +2.0/-0.0
(0.488 +0.078/-0.0)
18.4
(0.724)
16 mm
16.4 +2.0/-0.0
(0.646 +0.078/-0.0)
22.4
(0.882)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 9/20/2013 16
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Figure 7 – Tape Leader & Trailer Dimensions
Trailer
160 mm Minimum
Carrier Tape
END START
Round Sprocket Holes
Elongated Sprocket Holes
(32 mm tape and wider)
Top Cover Tape
Top Cover Tape
Punched Carrier
8 mm & 12 mm only
Embossed Carrier
Components
100 mm
Minimum Leader
400 mm Minimum
Figure 8 – Maximum Camber
Carrier Tape
Round Sprocket Holes
1 mm Maximum, either direction
Straight Edge
250 mm
Elongated sprocket holes
(32 mm & wider tapes)
Bulk Cassette Packaging (Ceramic Chips Only)
MeetsDimensionalRequirementsIEC–286andEIAJ7201
Unit mm *Reference
110 ± 0.7
31.5 ± 0
0.2
36 ± 0
0.2
19.0*
5 0*
10*
53 3*
68 ± 0.1
88 ± 0.1
12.0 ± 0.1
3.0 ± 0
0.2
2.0 ± 0.1
0
1.5 ± 0
0.1
Capacitor Dimensions for Bulk Cassette
Cassette Packaging – Millimeters
EIA Size
Code
Metric Size
Code
L Length W Width B Bandwidth
S Separation
Minimum
T Thickness
Number of
Pieces/Cassette
0402 1005 1.0 ±0.05 0.5 ±0.05 0.2 to 0.4 0.3 0.5 ±0.05 50,000
0603 1608 1.6 ±0.07 0.8 ±0.07 0.2 to 0.5 0.7 0.8 ±0.07 15,000
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 9/20/2013 17
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
KEMET Corporation
World Headquarters
2835KEMETWay
Simpsonville, SC 29681
MailingAddress:
P.O. Box 5928
Greenville, SC 29606
www.kemet.com
Tel:864-963-6300
Fax:864-963-6521
Corporate Of ces
FortLauderdale,FL
Tel:954-766-2800
North America
Southeast
LakeMary,FL
Tel:407-855-8886
Northeast
Wilmington,MA
Tel:978-658-1663
Central
Novi, MI
Tel:248-994-1030
West
Milpitas, CA
Tel:408-433-9950
Mexico
Guadalajara,Jalisco
Tel:52-33-3123-2141
Europe
Southern Europe
Paris, France
Tel:33-1-4646-1006
SassoMarconi,Italy
Tel:39-051-939111
Central Europe
Landsberg,Germany
Tel:49-8191-3350800
Kamen,Germany
Tel:49-2307-438110
Northern Europe
Bishop’sStortford,UnitedKingdom
Tel:44-1279-460122
Espoo,Finland
Tel:358-9-5406-5000
Asia
Northeast Asia
HongKong
Tel:852-2305-1168
Shenzhen,China
Tel:86-755-2518-1306
Beijing,China
Tel:86-10-5829-1711
Shanghai,China
Tel:86-21-6447-0707
Taipei, Taiwan
Tel:886-2-27528585
Southeast Asia
Singapore
Tel:65-6586-1900
Penang,Malaysia
Tel:60-4-6430200
Bangalore,India
Tel:91-806-53-76817
Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not
assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of
KEMET Electronics Corporation.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 9/20/2013 18
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Other KEMET Resources
Tools
Resource Location
CongureAPart:CapEdge http://capacitoredge.kemet.com
SPICE & FIT Software http://www.kemet.com/spice
SearchOurFAQs:KnowledgeEdge http://www.kemet.com/keask
ElectrolyticLifeCalculator http://www.kemet.com:8080/elc
Product Information
Resource Location
Products http://www.kemet.com/products
TechnicalResources(IncludingSolderingTechniques) http://www.kemet.com/technicalpapers
RoHSStatement http://www.kemet.com/rohs
QualityDocuments http://www.kemet.com/qualitydocuments
Product Request
Resource Location
Sample Request http://www.kemet.com/sample
Engineering Kit Request http://www.kemet.com/kits
Contact
Resource Location
Website www.kemet.com
Contact Us http://www.kemet.com/contact
Investor Relations http://www.kemet.com/ir
Call Us 1-877-MyKEMET
Twitter http://twitter.com/kemetcapacitors
Disclaimer
Allproductspecications,statements,informationanddata(collectively,the“Information”)inthisdatasheetaresubjecttochange.Thecustomerisresponsibleforcheckingand
verifyingtheextenttowhichtheInformationcontainedinthispublicationisapplicabletoanorderatthetimetheorderisplaced.
AllInformationgivenhereinisbelievedtobeaccurateandreliable,butitispresentedwithoutguarantee,warranty,orresponsibilityofanykind,expressedorimplied.
StatementsofsuitabilityforcertainapplicationsarebasedonKEMETElectronicsCorporation’s(“KEMET”)knowledgeoftypicaloperatingconditionsforsuchapplications,butare
notintendedtoconstitute–andKEMETspecicallydisclaims–anywarrantyconcerningsuitabilityforaspeciccustomerapplicationoruse.TheInformationisintendedforuseonly
bycustomerswhohavetherequisiteexperienceandcapabilitytodeterminethecorrectproductsfortheirapplication.AnytechnicaladviceinferredfromthisInformationorotherwise
providedbyKEMETwithreferencetotheuseofKEMET’sproductsisgivengratis,andKEMETassumesnoobligationorliabilityfortheadvicegivenorresultsobtained.
AlthoughKEMETdesignsandmanufacturesitsproductstothemoststringentqualityandsafetystandards,giventhecurrentstateoftheart,isolatedcomponentfailuresmaystill
occur.Accordingly,customerapplicationswhichrequireahighdegreeofreliabilityorsafetyshouldemploysuitabledesignsorothersafeguards(suchasinstallationofprotective
circuitryorredundancies)inordertoensurethatthefailureofanelectricalcomponentdoesnotresultinariskofpersonalinjuryorpropertydamage.
Althoughallproduct–relatedwarnings,cautionsandnotesmustbeobserved,thecustomershouldnotassumethatallsafetymeasuresareindictedorthatothermeasuresmaynot
berequired.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 9/20/2013 19
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Digitally signed by Marcy Brand
DN: c=US, st=FL, l=Fort Lauderdale, o=KEMET Corporation, ou=Marketing Communications, cn=Marcy Brand,
email=marcybrand@kemet.com
Date: 2013.09.20 14:24:54 -04'00'