*Common to Substrate and Case
Flat Package
S4S3
D4D3
D2D1
S2S1
IN2IN1
V+ V*
VLVR
1
2
3
4
5
6
7
14
13
12
11
10
9
8
Top View
D1S1
NC
Dual-In-Line
IN1
D3V
S3VR
S4VL
D4V+
NC IN2
D2S2
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
Top View
Refer to JAN38510 Information, Military Section
DG189/190/191
Vishay Siliconix
Document Number: 70034
S-51140—Rev. D, 20-Jun-05
www.vishay.com
1
High-Speed Drivers with Dual SPDT JFET Switches
FEATURES BENEFITS APPLICATIONS
DConstant On-Resistance Over
Entire Analog Range
DLow Leakage
DLow Crosstalk
DRad Hardness
DLow Distortion
DEliminates Large Signal Errors
DHigh Precision
DHigh Bandwidth Capability
DFault Protection
DAudio Switching
DVideo Switching
DSample/Hold
DGuidance and Control Systems
DAerospace
DESCRIPTION
The DG189/190/191 are precision dual single-pole,
double-throw (SPDT) analog switches designed to provide
accurate switching of video and audio signals. This series is
ideally suited for applications requiring a constant
on-resistance over the entire analog range.
The major difference in the devices is the on-resistance
(DG189—10 , DG190—30 , DG191—75  Reduced
errors are achieved through low leakage current (ID(on)
< 2 nA). Applications which benefit from the flat JFET
on-resistance include audio switching, video switching, and
data acquisition.
To achieve fast and accurate switch performance, each device
comprises four n-channel JFET transistors and a TTL
compatible bipolar driver. The driver is designed to achieve
break-before-make switching action, eliminating the
inadvertent shorting between channels and the crosstalk
which would result. In the on state, each switch conducts
current equally well in either direction. In the off condition, the
switches will block up to 20 V peak-to-peak, with feedthrough
of less than 60 dB at 10 MHz.
FUNCTIONAL BLOCK DIAGRAM AND PIN CONFIGURATION
TRUTH TABLE
Logic SW1, SW2SW3, SW4
0 OFF ON
1 ON OFF
Logic
0
v 08 V
L
og
i
c
“0”
v
0
.
8 V
Logic
1” w 24 V
g
Logic “1” w 2.4 V
DG189/190/191
Vishay Siliconix
www.vishay.com
2
Document Number: 70034
S-51140—Rev. D, 20-Jun-05
ORDERING INFORMATION
Temp Range Package Part Number
DG189BP
25 to 85_C16-Pin Sidebraze DG190BP
DG191BP
DG189AP
DG190AP
16 Pin Sidebraze
DG191AP
55 to 125
_
C
16-Pin Sidebraze DG189AP, DG189AP/883, 5962-9068901MEA
55 to 125_CDG190AP, DG190AP/883, JM38510/11107BEA
DG191AP, DG191AP/883, JM38510/11108BEA
14 Pin Flat Pack
JM38510/11107BXA
14-Pin Flat Pack JM38510/11108BXA
ABSOLUTE MAXIMUM RATINGS
V+ to V36 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
V+ to VD 33 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VS, VD to V−−0.3 to 33 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VD to VD "22 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VL to V36 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VL to VIN 8 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VL to VR 8 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VIN to VR8 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VR to V27 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VR to VIN 2 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current (S or D) DG189 200 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current (S or D) DG190, DG191 30 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current (All Other Pins) 30 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage Temperature 65 to 150_C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Dissipationa
16-Pin Sidebrazeb900 mW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14-Pin Flat Packc900 mW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notes:
a. All leads welded or soldered to PC Board.
b. Derate 12 mW/_C above 75_C
c. Derate 10 mW/_C above 75_C
SCHEMATIC DIAGRAM (TYPICAL CHANNEL)
FIGURE 1.
VR
VLV+
S
IN
D
V
DG189/190/191
Vishay Siliconix
Document Number: 70034
S-51140—Rev. D, 20-Jun-05
www.vishay.com
3
SPECIFICATIONSa FOR DG189
Test Conditions
Unless Specified
A Suffix
55 to 125_C
B Suffix
25 to 85_C
Parameter Symbol V+ = 15 V, V = 15 V, VL = 5 V
VR = 0 V, VIN = 0.8 V or 2 VfTempbTypcMindMaxdMindMaxdUnit
Analog Switch
Analog Signal RangeeVANALOG Full 7.5 15 7.5 15 V
Drain-Source
On-Resistance rDS(on) IS = 10 mA, VD = 7.5 V Room
Full
7.5 10
20
15
25
Source Off
IS( ff)
VS = "10 V, VD = #10 V
V+ = 10 V, V = 20 V
Room
Hot
0.05 10
1000
15
300
Source Off
Leakage Current IS(off)
VS = "7.5 V, VD = #7.5 V Room
Hot
0.05 10
1000
15
300
Drain Off
ID( ff)
VS = "10 V, VD = #10 V
V+ = 10 V, V = 20 V
Room
Hot
0.04 10
1000
15
300 nA
Drain Off
Leakage Current ID(off)
VS = "7.5 V, VD = #7.5 V Room
Hot
0.03 10
1000
15
300
Channel On
Leakage Current ID(on) VD = VS = "7.5 V Room
Hot
0.1 2
200
10
200
Saturation Drain Current IDSS 2 ms Pulse Duration Room 300 mA
Digital Input
Input Current with
Input Voltage High IINH VIN = 5 V Room
Hot
<0.01 10
20
10
20
A
Input Current with
Input Voltage Low IINL VIN = 0 V Full 30 250 250
A
Dynamic Characteristics
Turn-On Time ton
See Switching Time Test Circuit
Room 240 400 425
ns
Turn-Off Time toff
S
ee
S
w
i
tc
hi
ng
Ti
me
T
est
Ci
rcu
i
tRoom 140 200 225 ns
Source-Off Capacitance CS(off) VS = 5 V, ID = 0 Room 21
Drain-Off Capacitance CD(off) f = 1 MHz VD = 5 V, IS = 0 Room 17 pF
Channel-On Capacitance CD(on) VD = VS = 0 V Room 17
Off Isolation OIRR f = 1 MHz, RL = 75 Room >55 dB
Power Supplies
Positive Supply Current I+ Room 0.6 1.5 1.5
Negative Supply Current I
VIN = 0 V or 5 V
Room 2.7 55
mA
Logic Supply Current IL
V
IN
=
0 V
,
or
5 V
Room 3.1 4.5 4.5 m
A
Reference Supply Current IRRoom 122
Notes:
a. Refer to PROCESS OPTION FLOWCHART.
b. Room = 25_C, Full = as determined by the operating temperature suffix.
c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
d. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
e. Guaranteed by design, not subject to production test.
f. VIN = input voltage to perform proper function.
DG189/190/191
Vishay Siliconix
www.vishay.com
4
Document Number: 70034
S-51140—Rev. D, 20-Jun-05
SPECIFICATIONSa FOR DG190
Test Conditions
Unless Specified
A Suffix
55 to 125_C
B Suffix
25 to 85_C
Parameter Symbol V+ = 15 V, V = 15 V, VL = 5 V
VR = 0 V, VIN = 0.8 V or 2 VfTempbTypcMindMaxdMindMaxdUnit
Analog Switch
Analog Signal RangeeVANALOG Full 7.5 15 7.5 15 V
Drain-Source
On-Resistance rDS(on) IS = 10 mA, VD = 7.5 V Room
Full
18 30
60
50
75
Source Off
IS( ff)
VS = "10 V, VD = #10 V
V+ = 10 V, V = 20 V
Room
Hot
0.06 1
100
5
100
Source Off
Leakage Current IS(off)
VS = "7.5 V, VD = #7.5 V Room
Hot
0.1 1
100
5
100
Drain Off
ID( ff)
VS = "10 V, VD = #10 V
V+ = 10 V, V = 20 V
Room
Hot
0.05 1
100
5
100 nA
Drain Off
Leakage Current ID(off)
VS = "7.5 V, VD = #7.5 V Room
Hot
0.06 1
100
5
100
Channel On
Leakage Current ID(on) VD = VS = "7.5 V Room
Hot
0.02 2
200
10
200
Digital Input
Input Current with
Input Voltage High IINH VIN = 5 V Room
Hot
<0.01 10
20
10
20
Input Current with
Input Voltage Low IINL VIN = 0 V Full 30 250 250
A
Dynamic Characteristics
Turn-On Time ton
See Switching Time Test Circuit
Room 85 150 180
Turn-Off Time toff
See Switching Time Test Circuit Room 95 130 150 ns
Source-Off Capacitance CS(off) VS = 5 V, ID = 0 Room 9
Drain-Off Capacitance CD(off) f = 1 MHz VD = 5 V, IS = 0 Room 6 pF
Channel-On Capacitance CD(on) VD = VS = 0 V Room 14
Off Isolation OIRR f = 1 MHz, RL = 75 Room >50 dB
Power Supplies
Positive Supply Current I+ Room 0.6 1.5 1.5
Negative Supply Current I
VIN = 0 V or 5 V
Room 2.7 55
Logic Supply Current IL
V
IN
=
0 V
,
or
5 V
Room 3.1 4.5 4.5
m
Reference Supply Current IRRoom 122
Notes:
a. Refer to PROCESS OPTION FLOWCHART.
b. Room = 25_C, Full = as determined by the operating temperature suffix.
c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
d. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
e. Guaranteed by design, not subject to production test.
f. VIN = input voltage to perform proper function.
DG189/190/191
Vishay Siliconix
Document Number: 70034
S-51140—Rev. D, 20-Jun-05
www.vishay.com
5
SPECIFICATIONSa FOR DG191
Test Conditions
Unless Specified
A Suffix
55 to 125_C
B Suffix
25 to 85_C
Parameter Symbol V+ = 15 V, V = 15 V, VL = 5 V
VR = 0 V, VIN = 0.8 V or 2 VfTempbTypcMindMaxdMindMaxdUnit
Analog Switch
Analog Signal RangeeVANALOG Full 10 15 10 15 V
Drain-Source
On-Resistance rDS(on) IS = 10 mA, VD = 7.5 V Room
Full
35 75
150
100
150
Source Off
IS( ff)
VS = "10 V, VD = #10 V
V+ = 10 V, V = 20 V
Room
Hot
0.05 1
100
5
100
Source Off
Leakage Current IS(off)
VS = "10 V, VD = #10 V Room
Hot
0.07 1
100
5
100
Drain Off
ID( ff)
VS = "10 V, VD = #10 V
V+ = 10 V, V = 20 V
Room
Hot
0.04 1
100
5
100 nA
Drain Off
Leakage Current ID(off)
VS = "10 V, VD = #10 V Room
Hot
0.05 1
100
5
100
Channel On
Leakage Current ID(on) VD = VS = "10 V Room
Hot
0.03 2
200
10
200
Digital Input
Input Current with
Input Voltage High IINH VIN = 5 V Room
Hot
<0.01 10
20
10
20
A
Input Current with
Input Voltage Low IINL VIN = 0 V Full 30 250 250
A
Dynamic Characteristics
Turn-On Time ton
See Switching Time Test Circuit
Room 120 250 300
ns
Turn-Off Time toff
S
ee
S
w
i
tc
hi
ng
Ti
me
T
est
Ci
rcu
i
tRoom 100 130 150 ns
Source-Off Capacitance CS(off) VS = 5 V, ID = 0 Room 9
Drain-Off Capacitance CD(off) f = 1 MHz VD = 5 V, IS = 0 Room 6 pF
Channel-On Capacitance CD(on) VD = VS = 0 V Room 14
p
Off Isolation OIRR f = 1 MHz, RL = 75 Room >50 dB
Positive Supply Current I+ Room 0.6 1.5 1.5
Negative Supply Current I
VIN = 0 V or 5 V
Room 2.7 55
mA
Logic Supply Current IL
VIN = 0 V, or 5 V Room 3.1 4.5 4.5 mA
Reference Supply Current IRRoom 122
Notes:
a. Refer to PROCESS OPTION FLOWCHART.
b. Room = 25_C, Full = as determined by the operating temperature suffix.
c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
d. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
e. Guaranteed by design, not subject to production test.
f. VIN = input voltage to perform proper function.
DG189/190/191
Vishay Siliconix
www.vishay.com
6
Document Number: 70034
S-51140—Rev. D, 20-Jun-05
TYPICAL CHARACTERISTICS (25_C UNLESS NOTED)
, I, I+, I (mA)ILR
A)IIN (m
IIN vs. VIN and TemperatureSupply Current vs. Temperature
Temperature (_C) Temperature (_C)
5
4
3
2
1
0
55 35 15 5 25 45 65 85 105 125
0
100
80
60
40
20
55 35 15 5 25 45 65 85 105 125
IL
I+
IR
I
IINL
IINH
VINL = 0
VINH = 5 V
(ns)tON
,t
OFF
Temperature (_C)
Switching Time vs. VD and Temperature (DG189)rDS(on) vs. Temperature
Temperature (_C)
rDS(on) ()
100
1
50 25 0 25 50 75 100 125
10
230
90
55 35 15 5 25 45 65 85 105 125
210
190
170
150
130
110
VD= 7.5 V
IS = 10 mA
tOFF
tON
DG189
DG190
DG191
VD = 7.5 V
VD = 7.5 V
Leakage vs. Temperature (DG189) Switching Time vs. VD and Temperature (DG190/191)
(nA)I , I
SD
(ns)tON
,t
OFF
Temperature (_C) Temperature (_C)
100
0.1
25 45 65 85 105 125
10
1
ID(on)
ID(off)
IS(off)
V+ = 10 V
V = 20 V
VL = 5 V
VR = 0
130
50
55 35 15 5 25 45 65 85 105 125
120
110
100
90
80
70
60
tOFF
tON
VD = 7.5 V
VD = 7.5 V
DG189/190/191
Vishay Siliconix
Document Number: 70034
S-51140—Rev. D, 20-Jun-05
www.vishay.com
7
TYPICAL CHARACTERISTICS (25_C UNLESS NOTED)
(pF)CS, D
ID(off) vs. Temperature (DG190/191)
(nA)
ID
Temperature (_C)
100
10
1
0.1
25 45 65 85 105 125
B Suffix
A Suffix
Capacitance vs. VD or VS (DG189)
VD or VS Drain or Source Voltage (V)
30
26
22
18
14
10
840 4 8
CD(off)
CS(off)
CD(on)
f = 1 MHz
V+ = 10 V, V = 20 V
VD = 10 V, VS = 10 V
ISO (dB)
(pF)CS, D
Off Isolation vs. FrequencyCapacitance vs. VD or VS (DG190/191)
VD or VS Drain or Source Voltage (V) f Frequency (Hz)
100
90
80
70
60
50
40
30
20
10
0
105106107108
V+ = 15 V, V = 15 V
VR = 0, VL = 5 V
RL = 75
VIN w 220 mVRMS
DG189
DG190/191
20
18
16
14
12
10
8
6
4
2
0
10 86420 2 46 810
CD(off)
CS(off)
CD(on)
Capacitance is measured from test terminal
to common.
VINL = 0.8 V
VINH = 2 V
f = 1 MHz
DG189/190/191
Vishay Siliconix
www.vishay.com
8
Document Number: 70034
S-51140—Rev. D, 20-Jun-05
TEST CIRCUITS
Feedthrough due to charge injection may result in spikes at the leading and trailing edge of the output waveform.
FIGURE 2. Switching Time
Logic
Input
Switch
Output
tOFF
tON
tr <10 ns
tf <10 ns
90%
50%
0 V
3 V
0 V
0 V
90%
3 V
3 V
VL
V
V+
IN
CL
100 pF
RL
1 k
D1VO
S3
S1
VS2
VS1
15 V
+15 V+5 V
CL (includes fixture and stray capacitance)
tON: VS = 3 V
tOFF:V
S = 3 V
VR
D3
VOUT +VSx
RL
RL)rDS(on)
APPLICATION HINTSa
Switch
V+
Positive
Supply Voltage
(V)
V
Negative
Supply
Voltage
(V)
VL
Logic Supply
Voltage
(V)
VR
Reference
Supply
Voltage
(V)
VIN
Logic Input
Voltage
VINH(min)/VINL(max
)
(V)
VS
Analog
Voltage
Range
(V)
DG189
DG190
15b
10
12
15
20
12
5
5
5
GND
GND
GND
2.0/0.8
2.0/0.8
2.0/0.8
7.5 to 15
12.5 to 10
4.5 to 12
DG191
15b
10
12
15
20
12
5
5
5
GND
GND
GND
2.0/0.8
2.0/0.8
2.0/0.8
10 to 15
15 to 10
7 to 12
Notes:
a. Application Hints are for DESIGN AID ONLY, not guaranteed and not subject to production testing.
b. Electrical Parameter Chart based on V+ = 15 V, VL = 5 V, VR = GND
Document Number: 91000 www.vishay.com
Revision: 18-Jul-08 1
Disclaimer
Legal Disclaimer Notice
Vishay
All product specifications and data are subject to change without notice.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein
or in any other disclosure relating to any product.
Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any
information provided herein to the maximum extent permitted by law. The product specifications do not expand or
otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed
therein, which apply to these products.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this
document or by any conduct of Vishay.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless
otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such
applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting
from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding
products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners.