TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING r r TAOS100A - FEBRUARY 2010 Features PACKAGE FN DUAL FLAT NO-LEAD (TOP VIEW) D Ambient Light Sensing and Proximity Detection in Single Device D Ambient Light Sensing (ALS) - - - - Approximates Human Eye Response Programmable Analog Gain Programmable Integration Time Programmable Interrupt Function with Upper and Lower Threshold - Resolution Up to 16 Bits - Very High Sensitivity -- Operates Well Behind Darkened Glass - Up to 1,000,000:1 Dynamic Range D Proximity Detection D - Programmable Number of IR Pulses - Programmable Current Sink for the IR LED -- No Limiting Resistor Needed - Programmable Interrupt Function with Upper and Lower Threshold - Covers a 2000:1 Dynamic Range Programmable Wait Timer - Programmable from 2.72 ms to > 8 Seconds - Wait State -- 65 mA Typical Current VDD 1 6 SDA SCL 2 5 INT GND 3 4 LDR D I2C Interface Compatible D D - Up to 400 kHz (I2C Fast Mode) - Dedicated Interrupt Pin Small 2 mm 2 mm ODFN Package Sleep Mode -- 2.5 mA Typical Current Applications D D D D D Cell Phone Backlight Dimming Cell Phone Touch Screen Disable Notebook/Monitor Security Automatic Speakerphone Enable Automatic Menu Popup Description The TSL2771 family of devices provides both ambient light sensing (ALS) and proximity detection (when coupled with an external IR LED). The ALS approximates human eye response to light intensity under a variety of lighting conditions and through a variety of attenuation materials. The proximity detection feature allows a large dynamic range of operation for use in short distance detection behind dark glass such as in a cell phone or for longer distance measurements for applications such as presence detection for monitors or laptops. The programmable proximity detection enables continuous measurements across the entire range. In addition, an internal state machine provides the ability to put the device into a low power mode in between ALS and proximity measurements providing very low average power consumption. While useful for general purpose light sensing, the TSL2771 is particularly useful for display management with the purpose of extending battery life and providing optimum viewing in diverse lighting conditions. Display panel and keyboard backlighting can account for up to 30 to 40 percent of total platform power. The ALS features are ideal for use in notebook PCs, LCD monitors, flat-panel televisions, and cell phones. The proximity function is targeted specifically towards cell phone, LCD monitor, laptop, and flat-panel television applications. In cell phones, the proximity detection can detect when the user positions the phone close to their ear. The device is fast enough to provide proximity information at a high repetition rate needed when answering a phone call. It can also detect both close and far distances so the application can implement more complex algorithms to provide a more robust interface. In laptop or monitor applications, the product is sensitive enough to determine whether a user is in front of the laptop using the keyboard or away from the desk. This provides both improved "green" power saving capability and the added security to lock the computer when the user is not present. The LUMENOLOGY r Company Copyright E 2010, TAOS Inc. r Texas Advanced Optoelectronic Solutions Inc. 1001 Klein Road S Suite 300 S Plano, TX 75074 S (972) r 673-0759 www.taosinc.com 1 TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 Functional Block Diagram Prox Control GND Interrupt IR LED Constant Current Sink LDR Prox Integration Prox ADC INT Upper Limit Prox Data Lower Limit VDD = 2.4 V to 3.6 V SCL I2C Interface Wait Control Upper Limit Clear ADC Clear Clear Data ALS Control IR ADC IR Lower Limit SDA IR Data Detailed Description The TSL2771 light-to-digital device provides on-chip clear and IR diodes, integrating amplifiers, ADCs, accumulators, clocks, buffers, comparators, a state machine and an I2C interface. Each device combines one clear photodiode (visible plus infrared) and one infrared-responding (IR) photodiode. Two integrating ADCs simultaneously convert the amplified photodiode currents into a digital value providing up to 16 bits of resolution. Upon completion of the conversion cycle, the conversion result is transferred to the clear and IR data registers. This digital output can be read by a microprocessor through which the illuminance (ambient light level) in Lux is derived using an empirical formula to approximate the human eye response. Communication to the device is accomplished through a fast (up to 400 kHz), two-wire I2C serial bus for easy connection to a microcontroller or embedded controller. The digital output of the TSL2771 device is inherently more immune to noise when compared to an analog interface. The TSL2771 provides a separate pin for level-style interrupts. When interrupts are enabled and a pre-set value is exceeded, the interrupt pin is asserted and remains asserted until cleared by the controlling firmware. The interrupt feature simplifies and improves system efficiency by eliminating the need to poll a sensor for a light intensity or proximity value. An interrupt is generated when the value of an ALS or proximity conversion exceeds either an upper or lower threshold. In addition, a programmable interrupt persistence feature allows the user to determine how many consecutive exceeded thresholds are necessary to trigger an interrupt. Interrupt thresholds and persistence settings are configured independently for both ALS and proximity. Proximity detection requires only a single external IR LED. An internal LED driver can be configured to provide a constant current sink of 12.5 mA, 25 mA, 50 mA, or 100 mA of current. No external current limiting resistor is required. The number of proximity LED pulses can be programmed from 1 to 255 pulses. Each pulse has a 16-s period. This LED current coupled with the programmable number of pulses provides a 2000:1 contiguous dynamic range. Copyright E 2010, TAOS Inc. The LUMENOLOGY r Company r r 2 www.taosinc.com TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 Terminal Functions TERMINAL FN PKG NO. NAME TYPE DESCRIPTION 1 VDD Supply voltage. 2 SCL 3 GND 4 LDR O LED driver for proximity emitter -- up to 100 mA, open drain. 5 INT O Interrupt -- open drain. 6 SDA I/O I2C serial data I/O terminal -- serial data I/O for I2C . I I2C serial clock input terminal -- clock signal for I2C serial data. Power supply ground. All voltages are referenced to GND. Available Options DEVICE PACKAGE - LEADS INTERFACE DESCRIPTION ORDERING NUMBER TSL27711 FN-6 I2C Vbus = VDD Interface TSL27711FN TSL27713 FN-6 I2C Vbus = 1.8 V Interface TSL27713FN Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8 V Digital output voltage range, VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 3.8 V Digital output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -1 mA to 20 mA Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40C to 85C ESD tolerance, human body model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000 V Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: All voltages are with respect to GND. Recommended Operating Conditions MIN NOM MAX Supply voltage, VDD 2.4 3 3.6 V Operating free-air temperature, TA -30 70 C The LUMENOLOGY r Company UNIT Copyright E 2010, TAOS Inc. r r www.taosinc.com 3 TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 Operating Characteristics, VDD = 3 V, TA = 25C (unless otherwise noted) PARAMETER TEST CONDITIONS MIN Active -- ATIME = 100 ms IDD Supply current VOL INT SDA output low voltage INT, I LEAK Leakage current, SDA, SCL, INT pins I LEAK Leakage current, LDR pin VIH SCL SDA input high voltage SCL, VIL SCL SDA input low voltage SCL, TYP MAX 175 250 Wait mode 65 Sleep mode 2.5 A 4 3 mA sink current 0 0.4 6 mA sink current 0 0.6 -5 5 10 TSL27711 0.7 VDD TSL27713 1.25 UNIT V A A V TSL27711 0.3 VDD TSL27713 0.54 V ALS Characteristics, VDD = 3 V, TA = 25C, Gain = 16, AEN = 1 (unless otherwise noted) (Notes 1 ,2, 3) PARAMETER TEST CONDITIONS Dark ALS ADC count value Ee = 0, AGAIN = 120x, ATIME = 0xDB (100 ms) ALS ADC integration time step size ATIME = 0xFF CHANNEL MIN TYP MAX Clear 0 1 5 IR 0 1 5 2.58 2.72 ALS ADC Number of integration steps 1 Full scale ADC counts per step Full scale ADC count value ATIME = 0xC0 W/cm2, ALS ADC count value ALS ADC count value ratio: Clear/IR Re Irradiance responsivity G i scaling, Gain li relative l ti to t 1x gain i setting p = 625 nm, Ee = 171.6 ATIME = 0xF6 (27 ms) ms), GAIN = 16x See note 2. Clear p = 850 nm, Ee = 219.7 W/cm2, ATIME = 0xF6 (27 ms) ms), GAIN = 16x See note 3. Clear 4000 IR UNIT counts 2.9 ms 256 steps 1024 steps 65535 steps 5000 6000 790 counts 4000 IR 5000 6000 2800 p = 625 nm nm, ATIME = 0xF6 (27 ms) See note 2. 2 10 8 10.8 15 8 15.8 20.8 20 8 p = 850 nm nm, ATIME = 0xF6 (27 ms) See note 3. 3 41 56 68 p = 625 nm, ATIME = 0xF6 (27 ms) See note 2. Clear 29.1 IR 4.6 p = 850 nm, ATIME = 0xF6 (27 ms) See note 3. Clear 22.8 IR 12.7 counts/ (W/ cm2) 8x -10 10 16x -10 10 10 -10 10 120x % % NOTES: 1. Optical measurements are made using small-angle incident radiation from light-emitting diode optical sources. Visible 625 nm LEDs and infrared 850 nm LEDs are used for final product testing for compatibility with high-volume production. 2. The 625 nm irradiance Ee is supplied by an AlInGaP light-emitting diode with the following typical characteristics: peak wavelength p = 625 nm and spectral halfwidth 1/2 = 20 nm. 3. The 850 nm irradiance Ee is supplied by a GaAs light-emitting diode with the following typical characteristics: peak wavelength p = 850 nm and spectral halfwidth 1/2 = 42 nm. Copyright E 2010, TAOS Inc. The LUMENOLOGY r Company r r 4 www.taosinc.com TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 Proximity Characteristics, VDD = 3 V, TA = 25C, Gain = 16, PEN = 1 (unless otherwise noted) PARAMETER IDD TEST CONDITIONS CONDITION MIN TYP 2.58 2.72 Supply current -- LDR pulse on ADC conversion time step size 3 PTIME = 0xFF ALS ADC number of integration steps 1 Full scale ADC counts per step 0 Two or more pulses ISINK sink current @ 600 mV, LDR pin 75 100 PDRIVE=1 50 PDRIVE=2 25 PDRIVE=3 12.5 Proximity distance ms 256 steps 255 pulses steps s s 7.33 PDRIVE=0 Proximity LED Drive mA 16 Proximity pulse -- LED on time UNIT 2.9 1024 Proximity IR LED pulse count Proximity pulse period MAX 125 mA 18 inches Proximity Distance is dependent upon emitter properties the reflective properties of the proximity reflecting surface. The nominal value shown uses an IR emitter with a peak wavelength of 850nm and a 20 half angle. The proximity reflecting surface used is a 16" x 20" Kodak 90% grey card. 60 mw/SR, 100 mA, 64 pulses, open view (no glass). Note: Greater distances are achievable with appropriate system considerations. Wait Characteristics, VDD = 3 V, TA = 25C, Gain = 16, WEN = 1 (unless otherwise noted) PARAMETER Wait step size TEST CONDITIONS CHANNEL WTIME = 0xFF Wait number of integration steps MIN TYP 2.58 2.72 1 MAX UNIT 2.9 ms 256 steps AC Electrical Characteristics, VDD = 3 V, TA = 25C (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 400 kHz f(SCL) Clock frequency (I2C only) t(BUF) Bus free time between start and stop condition 1.3 s t(HDSTA) Hold time after (repeated) start condition. After this period, the first clock is generated. 0.6 s t(SUSTA) Repeated start condition setup time 0.6 s t(SUSTO) Stop condition setup time 0.6 s t(HDDAT) Data hold time 0 s t(SUDAT) Data setup time 100 ns t(LOW) SCL clock low period 1.3 s t(HIGH) SCL clock high period 0.6 tF Clock/data fall time 300 ns tR Clock/data rise time 300 ns Ci Input pin capacitance 10 pF 0 s Specified by design and characterization; not production tested. The LUMENOLOGY r Company Copyright E 2010, TAOS Inc. r r www.taosinc.com 5 TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 PARAMETER MEASUREMENT INFORMATION t(LOW) t(R) t(F) VIH SCL VIL t(HDSTA) t(BUF) t(HIGH) t(HDDAT) t(SUSTA) t(SUSTO) t(SUDAT) VIH SDA VIL P Stop Condition S S Start Condition Start P Stop t(LOWSEXT) SCLACK SCLACK t(LOWMEXT) t(LOWMEXT) t(LOWMEXT) SCL SDA Figure 1. Timing Diagrams Copyright E 2010, TAOS Inc. The LUMENOLOGY r Company r r 6 www.taosinc.com TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 TYPICAL CHARACTERISTICS LDR OUTPUT COMPLIANCE SPECTRAL RESPONSIVITY 112.5 1 Ch 0 100 0.8 87.5 Load Current -- mA Normalized Responsivity 100 mA 0.6 0.4 Ch 1 75 62.5 50 mA 50 37.5 25 mA 25 0.2 12.5 mA 12.5 0 300 400 500 600 700 800 0 0 900 1000 1100 0.3 - Wavelength - nm Figure 2 0.9 1.2 Figure 3 NORMALIZED RESPONSIVITY vs. ANGULAR DISPLACEMENT NORMALIZED IDD vs. VDD and TEMPERATURE 110% 0.6 VOL - Output Low Voltage - V 1.0 108% 104% 50C 25C 102% 100% 0C 98% 96% Optical Axis 0.8 106% Normalized Responsivity IDD Normalized @ 3 V, 25C 75C 0.6 0.4 0.2 94% 92% 2.7 2.8 2.9 3 3.1 3.2 3.3 VDD -- V 0 -90 -Q Figure 4 The LUMENOLOGY r Company +Q -60 -30 0 30 60 Q - Angular Displacement - 90 Figure 5 Copyright E 2010, TAOS Inc. r r www.taosinc.com 7 TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 PRINCIPLES OF OPERATION System State Machine The TSL2771 provides control of ALS, proximity detection, and power management functionality through an internal state machine (Figure 6). After a power-on-reset, the device is in the sleep mode. As soon as the PON bit is set, the device will move to the start state. It will then continue through the Prox, Wait, and ALS states. If these states are enabled, the device will execute each function. If the PON bit is set to 0, the state machine will continue until all conversions are completed and then go into a low power sleep mode. Sleep PON = 1 (r 0:b0) PON = 0 (r 0:b0) Start Prox ALS Wait Figure 6. Simplified State Diagram NOTE: In this document, the nomenclature uses the bit field name in italics followed by the register number and bit number to allow the user to easily identify the register and bit that controls the function. For example, the power on (PON) is in register 0, bit 0. This is represented as PON (r0:b0). Clear and IR Diodes Conventional silicon detectors respond strongly to infrared light, which the human eye does not see. This can lead to significant error when the infrared content of the ambient light is high (such as with incandescent lighting) due to the difference between the silicon detector response and the brightness perceived by the human eye. This problem is overcome in the TSL2771 through the use of two photodiodes. One of the photodiodes, referred to as the clear channel, is sensitive to both visible and infrared light while the second photodiode is sensitive primarily to infrared light. Two integrating ADCs convert the photodiode currents to digital outputs. The IRDATA digital value is used to compensate for the effect of the infrared component of light on the CDATA (clear) digital value. The ADC digital outputs from the two channels are used in a formula to obtain a value that approximates the human eye response in units of lux. Copyright E 2010, TAOS Inc. The LUMENOLOGY r Company r r 8 www.taosinc.com TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 ALS Operation The ALS engine contains ALS gain control (AGAIN) and two integrating analog-to-digital converters (ADC) for the clear and IR photodiodes (Figure 7). The ALS integration time (ATIME) impacts both the resolution and the sensitivity of the ALS reading. Integration of both channels occurs simultaneously and upon completion of the conversion cycle, the results are transferred to the clear and IR data registers (CDATAx and IR DATAx). This data is also referred to as channel count. The transfers are double-buffered to ensure that invalid data is not read during the transfer. After the transfer, the device automatically moves to the next state in accordance with the configured state machine. ATIME(r 1) 2.72 ms to 700 ms Clear ALS Clear CDATAH(r 0x15), CDATAL(r 0x14) Clear Data ALS Control IR IR ADC IR Data IRDATAH(r 0x17), IRDATAL(r 0x16) AGAIN(r 0x0F, b1:0) 1, 8, 16, 120 Gain Figure 7. ALS Operation The ALS gain can be set to amplify the clear channel and IR channel by 1, 8, 16, or 120x. The register bits CONTROL (r0x0F, b1:0) are used to set the gain. Integration time can be set from 2.7ms to 700ms. The registers for programming the integration and wait times are a 2's compliment values. The actual time can be calculated as follows: ATIME = 256 - Integration Time / 2.72 ms Inversely, the time can be calculated from the register value as follows: Integration Time = 2.72 ms x (256 - ATIME) For example, if a 100-ms integration time is needed, the device needs to be programmed to: 256 - (100 / 2.72) = 256 - 37 = 219 = 0xDB Conversely, the programmed value of 0xC0 would correspond to: (256 - 0xC0) x 2.72 = 64 x 2.72 = 172 ms. The LUMENOLOGY r Company Copyright E 2010, TAOS Inc. r r www.taosinc.com 9 TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 Calculating Lux The lux calculation is a function of several factors including the clear channel count (CDATA), IR channel count (IRDATA), ALS gain (AGAIN), and ALS integration time (ATIME). The Clear and IR channel information is used to calculate an IR Factor (IRF) and IR adjusted count (IAC), which indicates the attenuation to the clear channel to account for the IR content in the signal. The IR Factor is calculated based on empirical device measurements under different lighting conditions. Count per lux (CPL) is a function of the AGAIN, ATIME, light attenuation, and a device factor (DF). Lux is also dependent upon light attenuation, referred to as glass attenuation (GA). This is used to scale the lux value to account for some interference such as an aperture, neutral density filter, or a light pipe. If light is attenuated equally across the spectrum (300 nm to 1100 nm), then a linear GA can be used to compensate for the light loss of the system. If the sensor is exposed to light without an aperture in an open-air system, then GA is unity. If the GA is nonlinear, then the IR Factor and LPC will need to be derived under the new conditions. The lux value can be calculated from the following equation: lux = IR Adjusted Count (IAC) x Counts per lux (CPL) Where: IAC = IRF x CDATA CPL = Integration Time x Gain / GA x DF For the TSL2771x FN package in open air to the light source, this factor is 52. RAW Channel Data Lux is calculated as a function of the clear count (CDATA) and IR count (IRDATA). Because all registers are byte-oriented, 16-bit DATA must be created from two register reads: CDATA = 256 x CDATAH (r0x15) + CDATA (r0x14) Likewise: IRDATA = 256 x IRDATAH (r0x17) + IRDATA (r0x16) Saturation The device can saturate if the light is brighter than can be accumulated with the light-to-frequency conversion. The full scale value for saturation will depend upon the integration time programmed into the device. In saturation, the device accumulates 1024 counts for each 2.72 ms of integration time programmed. For each ATIME programmed, the maximum count (saturation level) is the lesser of (1024 x (256 - ATIME)) or 65,535. There is also a second condition that impacts saturation. If there is ripple in the received signal, such as under fluorescent lights, then the signal will go in and out of saturation and the value read from clear or IR channel will be less than the maximum but still have some effects of being saturated. Because of this, it is necessary to lower gain if channel values are above 70% of the saturated calculation. This is especially true in high gain mode with AC-modulated light sources that produce flicker. Under this condition, a channel reading may be slightly below the saturated calculation but in reality be saturated during the peaks, resulting in a value less than the actual light level. If the ALS integration time is greater than 172 s, the saturation level is 50,000, otherwise it is calculated as: SATURATION = 0.75 x (1024 x (256 - ATIME) - 1) Copyright E 2010, TAOS Inc. The LUMENOLOGY r Company r r 10 www.taosinc.com TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 IR Factor and IAC The IR factor (IRF) is derived from the clear channel (CDATA), which is sensitive to both visible and infrared light, and the IR channel (IRDATA), which is sensitive primarily to infrared light. The IR Factor is calculated based on the ratio of the two photodiodes, which provides an optimized equation. RATIO = IRDATA / CDATA Because the two photodiodes have different spectral responses, the ratio of the channels will vary depending on a particular light source's spectral power distribution (SPD). Light sources such as an incandescent bulb or sunlight have high amounts of infrared energy, while fluorescent bulbs have virtually no infrared energy. Fluorescent lights have an IR Factor of approximately 80%; while incandescent light sources, with large amounts IR, have IR Factors between 10% and 20%. IRF = (1.000 - 1.846 x RATIO) IRF = (1.268 - 2.740 x RATIO) IRF = (0.749 - 1.374 x RATIO) IRF = (0.477 - 0.769 x RATIO) IRF = 0 For RATIO = 0% to 30% For RATIO = 30% to 38% For RATIO = 38% to 45% For RATIO = 45% to 54% For RATIO > 54% IRF is used in understanding the light attenuation under different circumstances. However, it is seldom calculated in the actual implementation. IAC is typically used such that the RATIO not needed in this calculation. IAC = (1.000 x CDATA - 1.846 x IRDATA) IAC = (1.268 x CDATA - 2.740 x IRDATA) IAC = (0.749 x CDATA - 1.374 x IRDATA) IAC = (0.477 x CDATA - 0.769 x IRDATA) IAC = 0 For RATIO = 0% to 30% For RATIO = 30% to 38% For RATIO = 38% to 45% For RATIO = 45% to 54% For RATIO > 54% Sample Lux Calculation Assume: GA = 1, Gain = 16, Integration Time = 200 ms Clear Data = 19476, IR Data = 1438 decimal First, calculate IAC Ratio = IRDATA / CDATA = 1438 / 19476 = 7.4% For a ratio of 7.4%, use the first equation: IAC = (1.000 x CDATA - 1.846 x IRDATA) IAC = (1.000 x 19476 - 1.846 x 1438) IAC = 16821 Next, calculate CPL: CPL = (Integration Time x Gain) / GA x DF CPL = 200 x 16 / (1 x 52) CPL = 61.5 Finally, calculate lux: lux = 16821 / 61.5 lux = 273 Various techniques can be used to eliminate floating point calculations such as multiplying coefficients by 1000 or 1024. Care must be taken to keep the math in the integer size allocated and to keep the appropriate amount of precision to avoid round-off errors. The LUMENOLOGY r Company Copyright E 2010, TAOS Inc. r r www.taosinc.com 11 TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 Fluorescent Ripple Rejection There are many factors that will impact the decision on which value to use for integration time and gain. One of the first factors is 50/60-Hz ripple rejection for fluorescent lighting. The programmed value needs to be multiples of 10 / 8.3 ms, or the half cycle time. Both frequencies can be rejected with a programmed value of 50 ms (ATIME=0xED). With this value, the resolution will be 1.3 lux per count. If higher resolution is needed, a longer integration time may be needed. In this case, the integration time should be programmed in multiples of 50. Recommended ALS Operations With the programming versatility of the integration time and gain, it can be difficult to understand when to use the different modes. Figure 8 shows a plot of the IRF equations. Figure 9 shows a log-log plot of the lux vs. integration time and gain with a spectral factor of unity and no IR present. GAIN AND INTEGRATION TIME to LUX (with NO IR) ATTENUATION vs. CH1 /CH0 Ratio 1 100 k 0.9 Fluorescent 10 k 0.8 1000 0.6 100 Lux I R Factor 0.7 0.5 10 0.4 0.3 1 0.2 Incandescent 0.1 0.1 0 0.01 0 0.2 0.4 0.6 0.8 1 100 10000 Counts CH1 / CH0 Ratio Figure 9 Figure 8 The maximum illuminance that can be measured is approximately 19 k-lux with no IR present. The intercept with a count of 1 shows the resolution of each setting. The lux values in the table increase as the SF increases (spectral attenuation increases). For example, if a 10% transmissive glass is used, the lux values would all be multiplied by 10. The lux values in the table decrease as the IR Factor decreases. For example, with a 10% IR Factor, which corresponds to a strong incandescent light, the Lux value would need to be divided by 10. The light level is the next determining factor for configuring device settings. Under bright conditions, the count will be fairly high. If a low light measurement is needed, a higher gain and/or longer integration time will be needed. As a general rule, it is recommended to have a clear channel count of at least 10 to accurately apply the lux equation. The digital accumulation is limited to 16 bits, which occurs at an integration time of 173 ms. This is the maximum recommended programmed integration time before increasing the gain. (150 ms is the maximum to reduce the fluorescent ripple.) Copyright E 2010, TAOS Inc. The LUMENOLOGY r Company r r 12 www.taosinc.com TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 Proximity Detection Proximity sensing uses an external light source (generally an infrared emitter) to emit light, which is then viewed by the integrated light detector to measure the amount of reflected light when an object is in the light path (Figure 10). The amount of light detected from a reflected surface can then be used to determine an object's proximity to the sensor. Surface Reflectivity (SR) Glass Attenuation (GA) Distance (D) IR LED 2771 Background Energy (BGE) Optical Crosstalk (OC) Figure 10. Proximity Detection The TSL2771 has controls for the number of IR pulses (PPCOUNT), the integration time (PTIME), the LED drive current (PDRIVE), and the photodiode configuration (PDIODE) (Figure 11). The photodiode configuration can be set to infrared diode (recommended), clear diode, or a combination of both diodes. At the end of the integration cycle, the results are latched into the proximity data (PDATA) register. IR LED VDD PDRIVE(r 0x0F, b7:6) PTIME(r 2) IR LED Constant Current Sink Prox Control Prox Integration Clear Prox ADC IR Prox Data PDATAH(r 0x019), PDATAL(r 0x014) PPCOUNT(r 0x0E) Figure 11. Proximity Detection Operation The LED drive current is controlled by a regulated current sink on the LDR pin. This feature eliminates the need to use a current limiting resistor to control LED current. The LED drive current can be configured for 12.5 mA, 25 mA, 50 mA, or 100 mA. For higher LED drive requirements, an external P type transistor can be used to control the LED current. The number of LED pulses can be programmed to any value between 1 and 255 pulses as needed. Increasing the number of LED pulses at a given current will increase the sensor sensitivity. Sensitivity grows by the square root of the number of pulses. Each pulse has a 16-s period. The LUMENOLOGY r Company Copyright E 2010, TAOS Inc. r r www.taosinc.com 13 TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 Add IR + Background Subtract Background LED On LED Off 16 ms IR LED Pulses Figure 12. Proximity IR LED Waveform The proximity integration time (PTIME) is the period of time that the internal ADC converts the analog signal to a digital count. It is recommend that this be set to a minimum of PTIME = 0xFF or 2.72 ms. The combination of LED power and number of pulses can be used to control the distance at which the sensor can detect proximity. Figure 13 shows an example of the distances covered with settings such that each curve covers 2x the distance. Counts up to 64 pulses provide a 16x range. PROXIMITY ADC COUNT vs. RELATIVE DISTANCE 1000 25 mA, 1 Pulse 100 mA, 64 Pulses Proximity ADC Count 800 100 mA, 16 Pulses 600 400 100 mA, 4 Pulses 100 mA, 1 Pulse 200 0 1 2 4 8 16 Relative Distance Figure 13 Copyright E 2010, TAOS Inc. The LUMENOLOGY r Company r r 14 www.taosinc.com TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 Interrupts The interrupt feature of the TSL2771 simplifies and improves system efficiency by eliminating the need to poll the sensor for a light intensity or proximity value. The interrupt mode is determined by the PIEN or AIEN field in the ENABLE register. The TSL2771 implements four 16-bit-wide interrupt threshold registers that allow the user to define thresholds above and below a desired light level. For ALS, an interrupt can be generated when the ALS clear data (CDATA) exceeds the upper threshold value (AIHTx) or falls below the lower threshold (AILTx). For proximity, an interrupt can be generated when the proximity data (PDATA) exceeds the upper threshold value (PIHTx) or falls below the lower threshold (PILTx). To further control when an interrupt occurs, the TSL2771 provides an interrupt persistence feature. This feature allows the user to specify a number of conversion cycles for which an event exceeding the ALS interrupt threshold must persist (APERS) or the proximity interrupt threshold must persist (PPERS) before actually generating an interrupt. Refer to the register descriptions for details on the length of the persistence. Prox Integration Prox ADC PIHTH(r 0x0B), PIHTL(r 0x0A8) PPERS(r 0x0C, b7:4) Upper Limit Prox Persistence Prox Data Lower Limit PILTH(r 09), PILTL(r 08) AIHTH(r 07), AIHTL(r 06) Upper Limit Clear ADC Clear APERS(r 0x0C, b3:0) ALS Persistence Clear Data Lower Limit IR IR ADC IR Data AILTH(r 05), AILTL(r 04) Figure 14. Programmable Interrupt The LUMENOLOGY r Company Copyright E 2010, TAOS Inc. r r www.taosinc.com 15 TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 State Diagram Figure 15 shows a more detailed flow for the state machine. The device starts in the sleep mode. The PON bit is written to enable the device. A 2.7-ms delay will occur before entering the start state. If the PEN bit is set, the state machine will step through the proximity states of proximity accumulate and then proximity ADC conversion. As soon as the conversion is complete, the state machine will move to the following state. If the WEN bit is set, the state machine will then cycle through the wait state. If the WLONG bit is set, the wait cycles are extended by 12x over normal operation. When the wait counter terminates, the state machine will step to the ALS state. The AEN should always be set, even in proximity-only operation. In this case, a minimum of 1 integration time step should be programmed. The ALS state machine will continue until it reaches the terminal count at which point the data will be latched in the ALS register and the interrupt set, if enabled. Up to 255 LED Pulses Pulse Frequency: 62.5 kHz Time: 16.3 ms - 4.2 ms Maximum 4.2ms Up to 255 steps Step: 2.72 ms Time: 2.72 ms - 696 ms 120 Hz Minimum - 8 ms 100 Hz Minimum - 10 ms Sleep PON = 1 PON = 0 Start Prox Accum ALS PEN = 1 Prox Check ALS Check Prox ADC ALS Delay AEN = 1 Up to 255 steps Step: 2.72 ms Time: 2.72 mS - 696 ms Recommended - 2.72 ms 1024 Counts Wait Check Time: 2.72 ms WEN = 1 Wait WLONG = 0 Counts up to 256 steps Step: 2.72 ms Time: 2.72 ms - 696 ms Minimum - 2.72 ms WLONG = 1 Counts up to 256 steps Step: 32.64 ms Time: 32.64 ms - 8.35 s Minimum - 32.64 ms Figure 15. Expanded State Diagram Copyright E 2010, TAOS Inc. The LUMENOLOGY r Company r r 16 www.taosinc.com TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 Power Management Power consumption can be controlled through the use of the wait state timing because the wait state consumes only 65 A of power. Figure 16 shows an example of using the power management feature to achieve an average power consumption of 155 A current with four 100-mA pulses of proximity detection and 50 ms of ALS detection. For I2C read and write transactions, if the PON bit is set to 0 the bit is overridden allowing the oscillator to be enabled. 4 IR LED Pulses Prox Accum Prox ADC 64 ms (32 ms LED On Time) 2.72 ms Example: 100 ms Cycle TIme WAIT 47 ms ALS 50 ms State Duration (ms) Current (mA) Prox Accum (LED On) Prox ADC Wait ALS 0.064 (0.032) 2.7 47 50 100.0 0.175 0.065 0.175 Avg = ((0.032 100) + (2.72 0.175) + (47 0.065) + (50 0.175)) / 100 = 155 mA Figure 16. Power Consumption Calculations The LUMENOLOGY r Company Copyright E 2010, TAOS Inc. r r www.taosinc.com 17 TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 Basic Software Operation The following pseudo code shows how to do basic initialization of the TSL2771. unit8 ATIME,PIME,WTIME,PPCOUNT; ATIME = 0xff; // 2.72ms - minimum ALS integration time WTIME = 0xff; // 2.72ms - minimum Wait time PTIME = 0xff; // 2.72ms - minimum Prox integration time PPCOUNT = 1; // Minimum prox pulse count WriteRegData(0, 0); //Disable and Powerdown WriteRegData (1, ATIME); WriteRegData (2, PTIME); WriteRegData (3, WTIME); WriteRegData (0xe, PPCOUNT); unit8 PDRIVE, PDIODE, PGAIN, AGAIN; PDRIVE = 0; //100mA of LED Power PDIODE = 0x20; // IR Diode PGAIN = 0; //1x Prox gain AGAIN = 0; //1x ALS gain WriteRegData (0xf, PDRIVE | PDIODE | PGAIN | AGAIN); unit8 WEN, PEN, AEN, PON; WEN = 8; // Enable Wait PEN = 4; // Enable Prox AEN = 2; // Enable ALS PON = 1; // Enable Power On WriteRegData (0, WEN | PEN | AEN | PON); Wait(12); // WriteRegData(0,0x0f); //Wait for 12 ms int Clear_data, IR_data, Prox_data; Clear_data = Read_Word(0x14); IR_data = Read_Word(0x16); Prox_data = Read_Word(0x18); WriteRegData (unit8 reg, unit 8 data); { m_I2CBus.WriteI2C(0x39, 0x80 | reg 1 &data); } unit16 Read_Word (unit8 reg); { unit8 barr [2]; m_I2CBus.ReadI2C(0x39, 0xA0 | reg, 2, ref barr); return (uint16)(barr[0] + 256 barr[1]); } Copyright E 2010, TAOS Inc. The LUMENOLOGY r Company r r 18 www.taosinc.com TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 I2C Protocol Interface and control of the TSL2771 is accomplished through an I2C serial compatible interface (standard or fast mode) to a set of registers that provide access to device control functions and output data. The device supports a single slave address of 0x39 hex using 7-bit addressing protocol. (Contact factory for other addressing options.) The I2C standard provides for three types of bus transaction: read, write, and a combined protocol (Figure 17). During a write operation, the first byte written is a command byte followed by data. In a combined protocol, the first byte written is the command byte followed by reading a series of bytes. If a read command is issued, the register address from the previous command will be used for data access. Likewise, if the MSB of the command is not set, the device will write a series of bytes at the address stored in the last valid command with a register address. The command byte contains either control information or a 5-bit register address. The control commands can also be used to clear interrupts. For a complete description of I2C protocols, please review the I2C Specification at: http://www.semiconductors.philips.com. A N P R S S W ... Acknowledge (0) Not Acknowledged (1) Stop Condition Read (1) Start Condition Repeated Start Condition Write (0) Continuation of protocol Master-to-Slave Slave-to-Master 1 7 1 1 S Slave Address W A 8 Command Code 1 8 1 A Data Byte A 8 1 1 ... P I2C Write Protocol 1 S 7 Slave Address 1 R 1 A 8 1 Data A Data A 1 ... P I2C Read Protocol 1 7 1 1 8 1 1 8 1 1 S Slave Address W A Command Code A S Data R A 8 Data 1 8 1 A Data A 1 ... P I2C Read Protocol -- Combined Format Figure 17. I2C Protocols The LUMENOLOGY r Company Copyright E 2010, TAOS Inc. r r www.taosinc.com 19 TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 Register Set The TSL2771 is controlled and monitored by data registers and a command register accessed through the serial interface. These registers provide for a variety of control functions and can be read to determine results of the ADC conversions. The register set is summarized in Table 1. Table 1. Register Address ADDRESS RESISTER NAME R/W -- COMMAND W 0x00 ENABLE 0x01 0x02 0x03 0x04 0x05 REGISTER FUNCTION RESET VALUE Specifies register address 0x00 R/W Enables states and interrupts 0x00 ATIME R/W ALS ADC time 0xFF PTIME R/W Proximity ADC time 0xFF WTIME R/W Wait time 0xFF AILTL R/W ALS interrupt low threshold low byte 0x00 AILTH R/W ALS interrupt low threshold high byte 0x00 0x06 AIHTL R/W ALS interrupt high threshold low byte 0x00 0x07 AIHTH R/W ALS interrupt high threshold high byte 0x00 0x08 PILTL R/W Proximity interrupt low threshold low byte 0x00 0x09 PILTH R/W Proximity interrupt low threshold high byte 0x00 0x0A PIHTL R/W Proximity interrupt high threshold low byte 0x00 0x0B PIHTH R/W Proximity interrupt high threshold high byte 0x00 0x0C PERS R/W Interrupt persistence filters 0x00 0x0D CONFIG R/W Configuration 0x00 0x0E PPCOUNT R/W Proximity pulse count 0x00 0x0F CONTROL R/W Gain control register 0x00 0x12 ID R Device ID 0x13 STATUS R Device status 0x00 0x14 CDATA R Clear ADC low data register 0x00 0x15 CDATAH R Clear ADC high data register 0x00 0x16 IRDATA R IR ADC low data register 0x00 0x17 IRDATAH R IR ADC high data register 0x00 0x18 PDATA R Proximity ADC low data register 0x00 0x19 PDATAH R Proximity ADC high data register 0x00 ID The mechanics of accessing a specific register depends on the specific protocol used. See the section on I2C protocols on the previous pages. In general, the COMMAND register is written first to specify the specific control/status register for following read/write operations. Copyright E 2010, TAOS Inc. The LUMENOLOGY r Company r r 20 www.taosinc.com TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 Command Register The command registers specifies the address of the target register for future write and read operations. Table 2. Command Register 7 6 COMMAND COMMAND FIELD BITS COMMAND 7 TYPE 6:5 5 4 3 TYPE 2 1 0 -- ADD DESCRIPTION Select Command Register. Must write as 1 when addressing COMMAND register. Selects type of transaction to follow in subsequent data transfers: FIELD VALUE INTEGRATION TIME 00 Repeated byte protocol transaction 01 Auto-increment protocol transaction 10 Reserved -- Do not use 11 Special function -- See description below Transaction type 00 will repeatedly read the same register with each data access. Transaction type 01 will provide an auto-increment function to read successive register bytes. ADD 4:0 Address register/special function register. Depending on the transaction type, see above, this field either specifies a special function command or selects the specific control-status-register for following write and read transactions: FIELD VALUE READ VALUE 00000 Normal -- no action 00101 Proximity interrupt clear 00110 ALS interrupt clear 00111 Proximity and ALS interrupt clear other Reserved -- Do not write ALS/Proximity Interrupt Clear. Clears any pending ALS/Proximity interrupt. This special function is self clearing. The LUMENOLOGY r Company Copyright E 2010, TAOS Inc. r r www.taosinc.com 21 TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 Enable Register (0x00) The ENABLE register is used to power the TSL2571 device on/off, enable functions, and interrupts. Table 3. Enable Register 7 6 Reserved ENABLE 5 4 3 2 1 0 PIEN Resv AIEN WEN PEN AEN PON Address 0x00 FIELD BITS DESCRIPTION Reserved 7:6 PIEN 5 Proximity interrupt mask. When asserted, permits proximity interrupts to be generated. AIEN 4 ALS interrupt mask. When asserted, permits ALS interrupts to be generated. WEN 3 Wait Enable. This bit activates the wait feature. Writing a 1 activates the wait timer. Writing a 0 disables the wait timer. PEN 2 Proximity enable. This bit activates the proximity function. Writing a 1 enables proximity. Writing a 0 disables proximity. AEN 1 ALS Enable. This bit actives the two channel ADC. Writing a 1 activates the ALS. Writing a 0 disables the ALS. PON 1, 2 0 Power ON. This bit activates the internal oscillator to permit the timers and ADC channels to operate. Writing a 1 activates the oscillator. Writing a 0 disables the oscillator. Reserved. Write as 0. NOTES: 1. See Power Management section for more information. 2. A minimum interval of 2.72 ms must pass after PON is asserted before either a proximity or ALS can be initiated. This required time is enforced by the hardware in cases where the firmware does not provide it. Copyright E 2010, TAOS Inc. The LUMENOLOGY r Company r r 22 www.taosinc.com TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 ALS Timing Register (0x01) The ALS timing register controls the internal integration time of the ALS clear and IR channel ADCs in 2.72 ms increments. Table 4. ALS Timing Register FIELD BITS ATIME 7:0 DESCRIPTION VALUE INTEG_CYCLES TIME MAX COUNT 0xFF 1 2.72 ms 1024 0xF6 10 27.2 ms 10240 0xDB 37 100 ms 37888 0xC0 64 174 ms 65535 0x00 256 696 ms 65535 Proximity Time Control Register (0x02) The proximity timing register controls the integration time of the proximity ADC in 2.72 ms increments. It is recommended that this register be programmed to a value of 0xFF (1 cycle, 1024 bits). Table 5. Proximity Time Control Register FIELD BITS PTIME 7:0 DESCRIPTION VALUE INTEG_CYCLES TIME MAX COUNT 0xFF 1 2.72 ms 1024 Wait Time Register (0x03) Wait time is set 2.72 ms increments unless the WLONG bit is asserted in which case the wait times are 12x longer. WTIME is programmed as a 2's complement number. Table 6. Wait Time Register FIELD BITS WTIME 7:0 DESCRIPTION REGISTER VALUE WAIT TIME TIME (WLONG = 0) TIME (WLONG = 1) 0xFF 1 2.72 ms 0.032 sec 0xB6 74 200 ms 2.4 sec 0x00 256 700 ms 8.3sec NOTE: The Proximity Wait Time Register should be configured before PEN and/or AEN is/are asserted. The LUMENOLOGY r Company Copyright E 2010, TAOS Inc. r r www.taosinc.com 23 TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 ALS Interrupt Threshold Register (0x04 - 0x07) The ALS interrupt threshold registers provides the values to be used as the high and low trigger points for the comparison function for interrupt generation. If the value generated by the ALS channel crosses below the low threshold specified, or above the higher threshold, an interrupt is asserted on the interrupt pin. Table 7. ALS Interrupt Threshold Register REGISTER ADDRESS BITS AILTL 0x04 7:0 ALS clear channel low threshold lower byte DESCRIPTION AILTH 0x05 7:0 ALS clear channel low threshold upper byte AIHTL 0x06 7:0 ALS clear channel high threshold lower byte AIHTH 0x07 7:0 ALS clear channel high threshold upper byte Proximity Interrupt Threshold Register (0x08 - 0x0B) The proximity interrupt threshold registers provide the values to be used as the high and low trigger points for the comparison function for interrupt generation. If the value generated by proximity channel crosses below the lower threshold specified, or above the higher threshold, an interrupt is signaled to the host processor. Table 8. Proximity Interrupt Threshold Register REGISTER ADDRESS BITS PILTL 0x08 7:0 Proximity ADC channel low threshold lower byte PILTH 0x09 7:0 Proximity ADC channel low threshold upper byte PIHTL 0x0A 7:0 Proximity ADC channel high threshold lower byte PIHTH 0x0B 7:0 Proximity ADC channel high threshold upper byte Copyright E 2010, TAOS Inc. DESCRIPTION The LUMENOLOGY r Company r r 24 www.taosinc.com TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 Persistence Register (0x0C) The persistence register controls the filtering interrupt capabilities of the device. Configurable filtering is provided to allow interrupts to be generated after each ADC integration cycle or if the ADC integration has produced a result that is outside of the values specified by threshold register for some specified amount of time. Separate filtering is provided for proximity and ALS functions. ALS interrupts are generated by looking only at the ADC integration results of CDATA. Table 9. Persistence Register 7 6 PERS 4 3 PPERS FIELD BITS PPERS 7:4 APERS 5 3:0 The LUMENOLOGY r Company 2 1 0 Address 0x0C APERS DESCRIPTION Proximity interrupt persistence. Controls rate of proximity interrupt to the host processor. FIELD VALUE MEANING INTERRUPT PERSISTENCE FUNCTION 0000 --- 0001 1 1 proximity value out of range 0010 2 2 consecutive proximity values out of range ... ... ... 1111 15 15 consecutive proximity values out of range Every proximity cycle generates an interrupt Interrupt persistence. Controls rate of interrupt to the host processor. FIELD VALUE MEANING 0000 Every INTERRUPT PERSISTENCE FUNCTION 0001 1 1 clear channel value outside of threshold range 0010 2 2 clear channel consecutive values out of range 0011 3 3 clear channel consecutive values out of range 0100 5 5 clear channel consecutive values out of range 0101 10 10 clear channel consecutive values out of range 0110 15 15 clear channel consecutive values out of range Every ALS cycle generates an interrupt 0111 20 20 clear channel consecutive values out of range 1000 25 25 clear channel consecutive values out of range 1001 30 30 clear channel consecutive values out of range 1010 35 35 clear channel consecutive values out of range 1011 40 40 clear channel consecutive values out of range 1100 45 45 clear channel consecutive values out of range 1101 50 50 clear channel consecutive values out of range 1110 55 55 clear channel consecutive values out of range 1111 60 60 clear channel consecutive values out of range Copyright E 2010, TAOS Inc. r r www.taosinc.com 25 TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 Configuration Register (0x0D) The configuration register sets the wait long time. Table 10. Configuration Register 7 6 5 CONFIG 4 3 2 Reserved 1 0 WLONG Reserved Address 0x0D FIELD BITS Reserved 7:2 DESCRIPTION WLONG 1 Wait Long. When asserted, the wait cycles are increased by a factor 12x from that programmed in the WTIME register. Reserved 0 Reserved. Write as 0. Reserved. Write as 0. Proximity Pulse Count Register (0x0E) The proximity pulse count register sets the number of proximity pulses that will be transmitted. When proximity detection is enabled, a proximity detect cycle occurs after each ALS cycle. PPULSE defines the number of pulses to be transmitted at a 62.5-kHz rate. NOTE: The ATIME register will be used to time the interval between proximity detection events even if the ALS function is disabled. Table 11. Proximity Pulse Count Register 7 6 5 PPULSE 4 3 2 1 Address 0x0E PPULSE FIELD BITS PPULSE 7:0 Copyright E 2010, TAOS Inc. DESCRIPTION Proximity Pulse Count. Specifies the number of proximity pulses to be generated. The LUMENOLOGY r Company r r 26 0 www.taosinc.com TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 Control Register (0x0F) The Control register provides eight bits of miscellaneous control to the analog block. These bits typically control functions such as gain settings and/or diode selection. Table 12. Gain Register 7 6 CONTROL 5 FIELD BITS 7:6 3 ResvPDIODE PDRIVE PDRIVE 4 2 Reserved 0 Address 0x0F AGAIN DESCRIPTION LED Drive Strength. FIELD VALUE PDIODE 1 5:4 LED STRENGTH 00 100 mA 01 50 mA 10 25 mA 11 12.5 mA Proximity Diode Select. FIELD VALUE DIODE SELECTION 00 Reserved 01 Proximity uses the clear (broadband) diode 10 Proximity uses the IR diode 11 Proximity uses both the clear diode and the IR 1 diode Reserved 3:2 Reserved. AGAIN 1:0 ALS Gain Control. Write bits as zero (0:0) FIELD VALUE ALS GAIN VALUE 00 1x gain 01 8x gain 10 16x gain 11 120x gain ID Register (0x12) The ID Register provides the value for the part number. The ID register is a read-only register. Table 13. ID Register 7 6 5 ID 4 3 2 1 Address 0x12 ID FIELD BITS ID 7:0 0 DESCRIPTION 0x00 = TSL27711 Part number identification The LUMENOLOGY r Company 0x08 = TSL27713 Copyright E 2010, TAOS Inc. r r www.taosinc.com 27 TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 Status Register (0x13) The Status Register provides the internal status of the device. This register is read only. Table 14. Status Register 7 STATUS 6 Reserved 5 4 PINT Resv AINT 3 2 1 0 Reserved AVALID FIELD BIT Reserved 7:6 PINT 5 Proximity Interrupt. Indicates that the device is asserting a proximity interrupt. AINT 4 ALS Interrupt. Indicates that the device is asserting an ALS interrupt. Reserved 3:1 AVALID 0 Address 0x13 DESCRIPTION Reserved. Reserved. ALS Valid. Indicates that the ALS clear / IR channels have completed an integration cycle. ADC Channel Data Registers (0x14 - 0x17) ALS clear and IR data are stored as two 16-bit values. To ensure the data is read correctly, a two-byte read I2C transaction should be used with auto increment protocol bits set in the command register. With this operation, when the lower byte register is read, the upper eight bits are stored in a shadow register, which is read by a subsequent read to the upper byte. The upper register will read the correct value even if additional ADC integration cycles end between the reading of the lower and upper registers. Table 15. ADC Channel Data Registers REGISTER ADDRESS BITS DESCRIPTION CDATAL 0x14 7:0 ALS clear data low byte CDATAH 0x15 7:0 ALS clear data high byte IRDATAL 0x16 7:0 ALS IR data low byte IRDATAH 0x17 7:0 ALS IR data high byte Proximity Data Register (0x18 - 0x19h) Proximity data is stored as a 16-bit value. To ensure the data is read correctly, a two-byte read I2C transaction should be utilized with auto increment protocol bits set in the command register. With this operation, when the lower byte register is read, the upper eight bits are stored into a shadow register, which is read by a subsequent read to the upper byte. The upper register will read the correct value even if the next ADC cycle ends between the reading of the lower and upper registers. Table 16. PDATA Registers Copyright E 2010, TAOS Inc. REGISTER ADDRESS BITS DESCRIPTION PDATAL 0x18 7:0 Proximity data low byte PDATAH 0x19 7:0 Proximity data high byte The LUMENOLOGY r Company r r 28 www.taosinc.com TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 APPLICATION INFORMATION: HARDWARE LED Driver Pin with Proximity Detection The application hardware circuit with proximity detection requires an LED connected as shown in Figure 18. Vbat may be an independent power source. If Vbat = Vdd (same source), however, tie the two power lines together as close to the source as possible. VBUS Vbat VDD LED 1 mF RP RP 1 mF TSL2771 RPI LDR INT SCL SDA Figure 18. Application Hardware Circuit for Proximity Sensing with Internal LED Driver If the hardware application requires more than 100 mA of current to drive the LED, then an external transistor should be used. Note, R2 should be sized adequately to bias the gate voltage given the LDR current mode setting. See Figure 19. VBUS Vbat VDD R2 1 mF RP RP RPI 1 mF LED R1 TSL2771 LDR INT SCL SDA Figure 19. Application Hardware Circuit for Proximity Sensing with External LED Driver Using P-FET Transistor The LUMENOLOGY r Company Copyright E 2010, TAOS Inc. r r www.taosinc.com 29 TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 APPLICATION INFORMATION: HARDWARE PCB Pad Layout Suggested PCB pad layout guidelines for the Dual Flat No-Lead (FN) surface mount package are shown in Figure 20. 2500 Note: Pads can be extended further if hand soldering is needed. 1000 1000 400 650 1700 650 400 NOTES: A. All linear dimensions are in micrometers. B. This drawing is subject to change without notice. Figure 20. Suggested FN Package PCB Layout Copyright E 2010, TAOS Inc. The LUMENOLOGY r Company r r 30 www.taosinc.com TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 MECHANICAL DATA PACKAGE FN TOP VIEW Dual Flat No-Lead Pin 1 Marker PIN OUT TOP VIEW PIN 1 2000 75 2000 75 VDD 1 6 SDA SCL 2 5 INT GND 3 4 LDR Photo-Active Area END VIEW SIDE VIEW 650 50 203 8 Seating Plane 650 300 50 BOTTOM VIEW 650 300 50 PIN 1 Pb 750 150 Lead Free NOTES: A. All linear dimensions are in micrometers. Dimension tolerance is 20 m unless otherwise noted. B. The photodiode active area is 466 m square and its center is 140 m above and 20 m to the right of the package center. The die placement tolerance is 75 m in any direction. C. Package top surface is molded with an electrically nonconductive clear plastic compound having an index of refraction of 1.55. D. Contact finish is copper alloy A194 with pre-plated NiPdAu lead finish. E. This package contains no lead (Pb). F. This drawing is subject to change without notice. Figure 21. Package FN -- Dual Flat No-Lead Packaging Configuration The LUMENOLOGY r Company Copyright E 2010, TAOS Inc. r r www.taosinc.com 31 TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 MECHANICAL DATA TOP VIEW 2.00 0.05 1.75 4.00 1.50 4.00 B + 0.30 8.00 - 0.10 3.50 0.05 1.00 0.25 A B A DETAIL B DETAIL A 5 Max 5 Max 0.254 0.02 2.18 0.05 NOTES: A. B. C. D. E. F. G. 2.18 0.05 0.83 0.05 Ao Bo Ko All linear dimensions are in millimeters. Dimension tolerance is 0.10 mm unless otherwise noted. The dimensions on this drawing are for illustrative purposes only. Dimensions of an actual carrier may vary slightly. Symbols on drawing Ao, Bo, and Ko are defined in ANSI EIA Standard 481-B 2001. Each reel is 178 millimeters in diameter and contains 3500 parts. TAOS packaging tape and reel conform to the requirements of EIA Standard 481-B. In accordance with EIA standard, device pin 1 is located next to the sprocket holes in the tape. This drawing is subject to change without notice. Figure 22. Package FN Carrier Tape Copyright E 2010, TAOS Inc. The LUMENOLOGY r Company r r 32 www.taosinc.com TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 MANUFACTURING INFORMATION The FN package has been tested and has demonstrated an ability to be reflow soldered to a PCB substrate. The process, equipment, and materials used in these test are detailed below. The solder reflow profile describes the expected maximum heat exposure of components during the solder reflow process of product on a PCB. Temperature is measured on top of component. The components should be limited to a maximum of three passes through this solder reflow profile. Table 17. TSL2771 Solder Reflow Profile PARAMETER REFERENCE TSL2771 Average temperature gradient in preheating Soak time 2.5C/sec tsoak 2 to 3 minutes Time above 217C t1 Max 60 sec Time above 230C t2 Max 50 sec Time above Tpeak -10C t3 Max 10 sec Peak temperature in reflow Tpeak 260C Temperature gradient in cooling Tpeak Max -5C/sec Not to scale -- for reference only T3 T2 Temperature (C) T1 Time (sec) t3 t2 tsoak t1 Figure 23. TSL2771 Solder Reflow Profile Graph The LUMENOLOGY r Company Copyright E 2010, TAOS Inc. r r www.taosinc.com 33 TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 MANUFACTURING INFORMATION Moisture Sensitivity Optical characteristics of the device can be adversely affected during the soldering process by the release and vaporization of moisture that has been previously absorbed into the package. To ensure the package contains the smallest amount of absorbed moisture possible, each device is dry-baked prior to being packed for shipping. Devices are packed in a sealed aluminized envelope called a moisture barrier bag with silica gel to protect them from ambient moisture during shipping, handling, and storage before use. The Moisture Barrier Bags should be stored under the following conditions: Temperature Range Relative Humidity Total Time < 40C < 90% No longer than 12 months from the date code on the aluminized envelope if unopened. Rebaking of the reel will be required if the devices have been stored unopened for more than 12 months and the Humidity Indicator Card shows the parts to be out of the allowable moisture region. Opened reels should be used within 168 hours if exposed to the following conditions: Temperature Range Relative Humidity < 30C < 60% If rebaking is required, it should be done at 50C for 12 hours. The FN package has been assigned a moisture sensitivity level of MSL 3. Copyright E 2010, TAOS Inc. The LUMENOLOGY r Company r r 34 www.taosinc.com TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 PRODUCTION DATA -- information in this document is current at publication date. Products conform to specifications in accordance with the terms of Texas Advanced Optoelectronic Solutions, Inc. standard warranty. Production processing does not necessarily include testing of all parameters. LEAD-FREE (Pb-FREE) and GREEN STATEMENT Pb-Free (RoHS) TAOS' terms Lead-Free or Pb-Free mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TAOS Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br) TAOS defines Green to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material). Important Information and Disclaimer The information provided in this statement represents TAOS' knowledge and belief as of the date that it is provided. TAOS bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TAOS has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TAOS and TAOS suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. NOTICE Texas Advanced Optoelectronic Solutions, Inc. (TAOS) reserves the right to make changes to the products contained in this document to improve performance or for any other purpose, or to discontinue them without notice. Customers are advised to contact TAOS to obtain the latest product information before placing orders or designing TAOS products into systems. TAOS assumes no responsibility for the use of any products or circuits described in this document or customer product design, conveys no license, either expressed or implied, under any patent or other right, and makes no representation that the circuits are free of patent infringement. TAOS further makes no claim as to the suitability of its products for any particular purpose, nor does TAOS assume any liability arising out of the use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. TEXAS ADVANCED OPTOELECTRONIC SOLUTIONS, INC. PRODUCTS ARE NOT DESIGNED OR INTENDED FOR USE IN CRITICAL APPLICATIONS IN WHICH THE FAILURE OR MALFUNCTION OF THE TAOS PRODUCT MAY RESULT IN PERSONAL INJURY OR DEATH. USE OF TAOS PRODUCTS IN LIFE SUPPORT SYSTEMS IS EXPRESSLY UNAUTHORIZED AND ANY SUCH USE BY A CUSTOMER IS COMPLETELY AT THE CUSTOMER'S RISK. LUMENOLOGY, TAOS, the TAOS logo, and Texas Advanced Optoelectronic Solutions are registered trademarks of Texas Advanced Optoelectronic Solutions Incorporated. The LUMENOLOGY r Company Copyright E 2010, TAOS Inc. r r www.taosinc.com 35 TSL2771 LIGHT-TO-DIGITAL CONVERTER with PROXIMITY SENSING TAOS100A - FEBRUARY 2010 Copyright E 2010, TAOS Inc. The LUMENOLOGY r Company r r 36 www.taosinc.com