LM4861 LM4861 1.1W Audio Power Amplifier with Shutdown Mode Literature Number: SNAS095B LM4861 1.1W Audio Power Amplifier with Shutdown Mode General Description Key Specifications The LM4861 is a bridge-connected audio power amplifier capable of delivering 1.1W of continuous average power to an 8 load with 1% THD+N using a 5V power supply. Boomer audio power amplifiers were designed specifically to provide high quality output power with a minimal amount of external components using surface mount packaging. Since the LM4861 does not require output coupling capacitors, bootstrap capacitors, or snubber networks, it is optimally suited for low-power portable systems. The LM4861 features an externally controlled, low-power consumption shutdown mode, as well as an internal thermal shutdown protection mechanism. The unity-gain stable LM4861 can be configured by external gain-setting resistors for differential gains of up to 10 without the use of external compensation components. Higher gains may be achieved with suitable compensation. j THD+N for 1kHz at 1W continuous average output power into 8 j Output power at 10% THD+N at 1kHz into 8 j Shutdown Current 1.0% (max) 1.5W (typ) 0.6A (typ) Features n No output coupling capacitors, bootstrap capacitors, or snubber circuits are necessary n Small Outline (SO) packaging n Compatible with PC power supplies n Thermal shutdown protection circuitry n Unity-gain stable n External gain configuration capability Applications n n n n Personal computers Portable consumer products Self-powered speakers Toys and games Connection Diagram Small Outline Package 01198602 Top View Order Number LM4861M See NS Package Number M08A Boomer (R) is a registered trademark of National Semiconductor Corporation. (c) 2003 National Semiconductor Corporation DS011986 www.national.com LM4861 1.1W Audio Power Amplifier with Shutdown Mode February 2003 LM4861 Typical Application 01198601 FIGURE 1. Typical Audio Amplifier Application Circuit www.national.com 2 See AN-450 "Surface Mounting and their Effects on Product Reliability" for other methods of soldering surface mount devices. (Note 2) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage Operating Ratings 6.0V Storage Temperature -65C to +150C Temperature Range -0.3V to VDD + 0.3V Input Voltage Power Dissipation (Note 3) Internally limited ESD Susceptibility (Note 4) 3000V ESD Susceptibility (Note 5) 250V Junction Temperature Soldering Information Small Outline Package Vapor Phase (60 sec.) Infrared (15 sec.) TMIN TA TMAX -40C TA +85C 2.0V VDD 5.5V Supply Voltage Thermal Resistance 150C 215C 220C JC (typ) -- M08A 35C/W JA (typ) -- M08A 140C/W JC (typ) -- N08E 37C/W JA (typ) -- N08E 107C/W Electrical Characteristics (Note 1) (Note 2) The following specifications apply for VDD = 5V, unless otherwise specified. Limits apply for TA = 25C. LM4861 Symbol VDD Parameter Conditions Typical Limit (Note 6) (Note 7) Supply Voltage Units (Limits) 2.0 V (min) 5.5 V (max) mA (max) IDD Quiescent Power Supply Current VIN = 0V, IO = 0A (Note 8) 6.5 10.0 ISD Shutdown Current Vpin1 = VDD 0.6 10.0 A (max) VOS Output Offset Voltage VIN = 0V 5.0 50.0 mV (max) 1.0 W (min) PO Output Power THD = 1% (max); f = 1 kHz 1.1 THD+N Total Harmonic Distortion + Noise PO = 1Wrms; 20 Hz f 20 kHz 0.72 % PSRR Power Supply Rejection Ratio VDD = 4.9V to 5.1V 65 dB Note 1: All voltages are measured with respect to the ground pin, unless otherwise specified. Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given, however, the typical value is a good indication of device performance. Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, JA, and the ambient temperature TA. The maximum allowable power dissipation is PDMAX = (TJMAX - TA)/JA or the number given in the Absolute Maximum Ratings, whichever is lower. For the LM4861, TJMAX = 150C, and the typical junction-to-ambient thermal resistance, when board mounted, is 140C/W. Note 4: Human body model, 100pF discharged through a 1.5k resistor. Note 5: Machine Model, 220pF-240pF discharged through all pins. Note 6: Typicals are measured at 25C and represent the parametric norm. Note 7: Limits are guaranteed to Nationai's AOQL (Average Outgoing Quality Level). Note 8: The quiescent power supply current depends on the offset voltage when a practical load is connected to the amplifier. 3 www.national.com LM4861 Absolute Maximum Ratings LM4861 High Gain Application Circuit 01198603 FIGURE 2. Audio Ampiifier with AVD = 20 Single Ended Application Circuit 01198604 *CS and CB size depend on specific application requirements and constraints. Typical vaiues of CS and CB are 0.1 F. **Pin 1 should be connected to VDD to disable the amplifier or to GND to enable the amplifier. This pin should not be left floating. ***These components create a "dummy" load for pin 8 for stability purposes. FIGURE 3. Single-Ended Amplifier with AV = -1 www.national.com 4 LM4861 External Components Description (Figures 1, 2) Components Functional Description 1. Ri Inverting input resistance which sets the closed-loop gain in conjunction with Rf. This resistor also forms a high pass filter with Ci at fC = 1 / (2 Ri Ci). 2. Ci Input coupling capacitor which blocks DC voltage at the amplifier's input terminals. Also creates a highpass filter with Ri at fC = 1 / (2 Ri Ci). 3. Rf Feedback resistance which sets closed-loop gain in conjunction with Ri. 4. CS Supply bypass capacitor which provides power supply filtering. Refer to the Application Information section for proper placement and selection of supply bypass capacitor. 5. CB Bypass pin capacitor which provides half supply filtering. Refer to the Application Information section for proper placement and selection of bypass capacitor. 6. Cf (Note 9) Cf in conjunction with Rf creates a low-pass filter which bandwidth limits the amplifier and prevents possible high frequency oscillation bursts. fC = 1 / (2 Rf Cf) Note 9: Optional component dependent upon specific design requirements. Refer to the Application Information section for more information. Typical Performance Characteristics THD+N vs Frequency THD+N vs Frequency 01198605 01198606 THD+N vs Frequency THD+N vs Output Power 01198607 01198609 5 www.national.com LM4861 Typical Performance Characteristics (Continued) Output Power vs Load Resistance THD+N vs Output Power 01198610 01198617 Output Power vs Supply Voltage Power Dissipation vs Output Power 01198618 01198616 Supply Current Distribution vs Temperature Noise Floor vs Frequency 01198615 01198614 www.national.com 6 LM4861 Typical Performance Characteristics (Continued) Supply Current vs Supply Voltage Power Derating Curve 01198613 01198612 Power Supply Rejection Ratio Open Loop Frequency Response 01198620 01198619 7 www.national.com LM4861 625mW.The maximum power dissipation point obtained from Equation 1 must not be greater than the power dissipation that results from Equation 2: PDMAX = (TJMAX - TA) / JA (2) Application Information BRIDGE CONFIGURATION EXPLANATION As shown in Figure 1 , the LM4861 has two operational amplifiers internally, allowing for a few different amplifier configurations. The first amplifier's gain is externally configurable, while the second amplifier is internally fixed in a unity-gain, inverting configuration. The closed-loop gain of the first amplifier is set by selecting the ratio of Rf to Ri while the second amplifier's gain is fixed by the two internal 40k resistors. Figure 1 shows that the output of amplifier one serves as the input to amplifier two which results in both amplifiers producing signals identical in magnitude, but out of phase 180. Consequently, the differential gain for the IC is: Avd = 2 * (Rf / Ri) By driving the load differentially through outputs VO1 and VO2, an amplifier configuration commonly referred to as "bridged mode" is established. Bridged mode operation is different from the classical single-ended amplifier configuration where one side of its load is connected to ground. A bridge amplifier design has a few distinct advantages over the single-ended configuration, as it provides differential drive to the load, thus doubling output swing for a specified supply voltage. Consequently, four times the output power is possible as compared to a single-ended amplifier under the same conditions. This increase in attainable output power assumes that the amplifier is not current limited or clipped. In order to choose an amplifier's closed-loop gain without causing excessive clipping which will damage high frequency transducers used in loudspeaker systems, please refer to the Audio Power Amplifier Design section. A bridge configuration, such as the one used in Boomer Audio Power Amplifiers, also creates a second advantage over single-ended amplifiers. Since the differential outputs, VO1 and VO2, are biased at half-supply, no net DC voltage exists across the load. This eliminates the need for an output coupling capacitor which is required in a single supply, single-ended amplifier configuration. Without an output coupling capacitor in a single supply, single-ended amplifier, the half-supply bias across the load would result in both increased internal IC power dissipation and also permanent loudspeaker damage. An output coupling capacitor forms a high pass filter with the load requiring that a large value such as 470F be used with an 8 load to preserve low frequency response. This combination does not produce a flat response down to 20Hz, but does offer a compromise between printed circuit board size and system cost, versus low frequency response. For the LM4861 surface mount package, JA = 140C/W and TJMAX = 150C. Depending on the ambient temperature, TA, of the system surroundings, Equation 2 can be used to find the maximum internal power dissipation supported by the IC packaging. If the result of Equation 1 is greater than that of Equation 2, then either the supply voltage must be decreased or the load impedance increased. For the typical application of a 5V power supply, with an 8 load, the maximum ambient temperature possible without violating the maximum junction temperature is approximately 62.5C provided that device operation is around the maximum power dissipation point. Power dissipation is a function of output power and thus, if typical operation is not around the maximum power dissipation point, the ambient temperature can be increased. Refer to the Typical Performance Characteristics curves for power dissipation information for lower output powers. POWER SUPPLY BYPASSING As with any power amplifier, proper supply bypassing is critical for low noise performance and high power supply rejection. The capacitor location on both the bypass and power supply pins should be as close to the device as possible. As displayed in the Typical Performance Characteristics section, the effect of a larger half supply bypass capacitor is improved low frequency THD+N due to increased half-supply stability. Typical applications employ a 5V regulator with 10F and a 0.1F bypass capacitors which aid in supply stability, but do not eliminate the need for bypassing the supply nodes of the LM4861. The selection of bypass capacitors, especially CB, is thus dependant upon desired low frequency THD+N, system cost, and size constraints. SHUTDOWN FUNCTION In order to reduce power consumption while not in use, the LM4861 contains a shutdown pin to externally turn off the amplifier's bias circuitry. The shutdown feature turns the amplifier off when a logic high is placed on the shutdown pin. Upon going into shutdown, the output is immediately disconnected from the speaker. A typical quiescent current of 0.6A results when the supply voltage is applied to the shutdown pin. In many applications, a microcontroller or microprocessor output is used to control the shutdown circuitry which provides a quick, smooth transition into shutdown. Another solution is to use a single-pole, single-throw switch that when closed, is connected to ground and enables the amplifier. If the switch is open, then a soft pull-up resistor of 47k will disable the LM4861. There are no soft pull-down resistors inside the LM4861, so a definite shutdown pin voltage must be applied externally, or the internal logic gate will be left floating which could disable the amplifier unexpectedly. POWER DISSIPATION Power dissipation is a major concern when designing a successful amplifier, whether the amplifier is bridged or single-ended. A direct consequence of the increased power delivered to the load by a bridge amplifier is an increase in internal power dissipation. Equation 1 states the maximum power dissipation point for a bridge amplifier operating at a given supply voltage and driving a specified output load. (1) PDMAX = 4*(VDD)2 / (22RL) Since the LM4861 has two operational amplifiers in one package, the maximum internal power dissipation is 4 times that of a single-ended amplifier. Even with this substantial increase in power dissipation, the LM4861 does not require heatsinking. From Equation 1, assuming a 5V power supply and an 8 load, the maximum power dissipation point is www.national.com HIGHER GAIN AUDIO AMPLIFIER The LM4861 is unity-gain stable and requires no external components besides gain-setting resistors, an input coupling capacitor, and proper supply bypassing in the typical application. However, if a closed-loop differential gain of greater than 10 is required, a feedback capacitor may be needed, as shown in Figure 2, to bandwidth limit the amplifier. This feedback capacitor creates a low pass filter that eliminates 8 LM4861 Application Information AUDIO POWER AMPLIFIER DESIGN (Continued) Design a 1W / 8 Audio Amplifier possible high frequency oscillations. Care should be taken when calculating the -3dB frequency in that an incorrect combination of Rf and Cf will cause rolloff before 20kHz. A typical combination of feedback resistor and capacitor that will not produce audio band high frequency rolloff is Rf = 100k and Cf = 5pF. These components result in a -3dB point of approximately 320kHz. Once the differential gain of the amplifier has been calculated, a choice of Rf will result, and Cf can then be calculated from the formula stated in the External Components Description section. Given: Power Output Load Impedance Input Level Input Impedance Bandwidth 1 Wrms 8 1 Vrms 20 k 100 Hz-20 kHz 0.25 dB A designer must first determine the needed supply rail to obtain the specified output power. By extrapolating from the Output Power vs Supply Voltage graph in the Typical Performance Characteristics section, the supply rail can be easily found. A second way to determine the minimum supply rail is to calculate the required Vopeak using Equation 3 and add the dropout voltage. Using this method, the minimum supply voltage would be (Vopeak + VOD , where VOD is typically 0.6V. VOICE-BAND AUDIO AMPLIFIER Many applications, such as telephony, only require a voiceband frequency response. Such an application usually requires a flat frequency response from 300Hz to 3.5kHz. By adjusting the component values of Figure 2, this common application requirement can be implemented. The combination of Ri and Ci form a highpass filter while Rf and Cf form a lowpass filter. Using the typical voice-band frequency range, with a passband differential gain of approximately 100, the following values of Ri, Ci, Rf, and Cf follow from the equations stated in the External Components Description section. Ri = 10k, Rf = 510k ,Ci = 0.22F, and Cf = 15pF Five times away from a -3dB point is 0.17dB down from the flatband response. With this selection of components, the resulting -3dB points, fL and fH, are 72Hz and 20kHz, respectively, resulting in a flatband frequency response of better than 0.25dB with a rolloff of 6dB/octave outside of the passband. If a steeper rolloff is required, other common bandpass filtering techniques can be used to achieve higher order filters. (3) For 1W of output power into an 8 load, the required Vopeak is 4.0V. A minumum supply rail of 4.6V results from adding Vopeak and Vod. But 4.6V is not a standard voltage that exists in many applications and for this reason, a supply rail of 5V is designated. Extra supply voltage creates dynamic headroom that allows the LM4861 to reproduce peaks in excess of 1Wwithout clipping the signal. At this time, the designer must make sure that the power supply choice along with the output impedance does not violate the conditions explained in the Power Dissipation section. Once the power dissipation equations have been addressed, the required differential gain can be determined from Equation 4. SINGLE-ENDED AUDIO AMPLIFIER Although the typical application for the LM4861 is a bridged monoaural amp, it can also be used to drive a load singleendedly in applications, such as PC cards, which require that one side of the load is tied to ground. Figure 3 shows a common single-ended application, where VO1 is used to drive the speaker. This output is coupled through a 470F capacitor, which blocks the half-supply DC bias that exists in all single-supply amplifier configurations. This capacitor, designated CO in Figure 3, in conjunction with RL, forms a highpass filter. The -3dB point of this high pass filter is 1/(2RLCO), so care should be taken to make sure that the product of RL and CO is large enough to pass low frequencies to the load. When driving an 8 load, and if a full audio spectrum reproduction is required, CO should be at least 470F. VO2, the output that is not used, is connected through a 0.1 F capacitor to a 2k load to prevent instability. While such an instability will not affect the waveform of VO1, it is good design practice to load the second output. (4) (5) Rf/Ri = AVD / 2 From equation 4, the minimum Avd is 2.83: Avd = 3 Since the desired input impedance was 20k, and with a Avd of 3, a ratio of 1:1.5 of Rf to Ri results in an allocation of Ri = 20k, Rf = 30k. The final design step is to address the bandwidth requirements which must be stated as a pair of -3dB frequency points. Five times away from a -3db point is 0.17dB down from passband response which is better than the required 0.25dB specified. This fact results in a low and high frequency pole of 20Hz and 100kHz respectively. As stated in the External Components section, Ri in conjunction with Ci create a highpass filter. Ci 1 / (2*20k*20Hz) = 0.397F; use 0.39F. The high frequency pole is determined by the product of the desired high frequency pole, fH, and the differential gain, Avd. With a Avd = 2 and fH = 100kHz, the resulting GBWP = 100kHz which is much smaller than the LM4861 GBWP of 4MHz. This figure displays that if a designer has a need to design an amplifier with a higher differential gain, the LM4861 can still be used without running into bandwidth problems. 9 www.national.com LM4861 LM4861 MDA MWA 1.1W Audio Power Amplifier with Shutdown Mode 01198626 Die Layout (B - Step) DIE/WAFER CHARACTERISTICS Fabrication Attributes General Die Information Physical Die Identification LM4861B Bond Pad Opening Size (min) 83m x 83m Die Step B Bond Pad Metalization ALUMINUM Passivation VOM NITRIDE Physical Attributes Wafer Diameter 150mm Back Side Metal BARE BACK Dise Size (Drawn) 1372m x 2032m 54.0mils x 80.0mils Back Side Connection GND Thickness 406m Nominal Min Pitch 108m Nominal Special Assembly Requirements: Note: Actual die size is rounded to the nearest micron. Die Bond Pad Coordinate Locations (B - Step) (Referenced to die center, coordinates in m) NC = No Connection, N.U. = Not Used SIGNAL NAME PAD# NUMBER X/Y COORDINATES PAD SIZE X Y X Y SHUTDOWN 1 -425 710 83 x BYPASS 2 -445 499 83 x 83 83 NC 3 -445 -34 83 x 170 NC 4 -445 -383 83 x 83 INPUT + 5 -445 -492 83 x 83 INPUT - 6 -352 -710 83 x 83 GND 7 -243 -710 83 x 83 Vo1 8 -91 -710 170 x 83 GND 9 445 -574 83 x 170 VDD 10 445 -2 83 x 170 NC 11 445 387 83 x 83 GND 12 445 633 83 x 170 Vo2 13 -63 710 170 x 83 GND 14 -215 710 83 x 83 www.national.com 10 LM4861 LM4861 MDA MWA 1.1W Audio Power Amplifier with Shutdown Mode (Continued) IN U.S.A Tel #: 1 877 Dial Die 1 877 342 5343 Fax: 1 207 541 6140 IN EUROPE Tel: 49 (0) 8141 351492 / 1495 Fax: 49 (0) 8141 351470 IN ASIA PACIFIC Tel: (852) 27371701 IN JAPAN Tel: 81 043 299 2308 11 www.national.com LM4861 1.1W Audio Power Amplifier with Shutdown Mode Physical Dimensions inches (millimeters) unless otherwise noted 8-Lead (0.150" Wide) Molded Small Outllne Package, JEDEC (M) Order Number LM4861 NS Package Number M08A LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Support Center Fax: 65-6250 4466 Email: ap.support@nsc.com Tel: 65-6254 4466 National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: nsj.crc@jksmtp.nsc.com Tel: 81-3-5639-7560 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated