CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers PRODUCT FEATURES Datasheet General Description Applications The CAP1133, which incorporates SMSC's RightTouch(R) 1 technology, is a multiple channel Capacitive Touch sensor with multiple power LED drivers. It contains three (3) individual capacitive touch sensor inputs with programmable sensitivity for use in touch sensor applications. Each sensor input automatically recalibrates to compensate for gradual environmental changes. The CAP1133 also contains three (3) LED drivers that offer full-on / off, variable rate blinking, dimness controls, and breathing. Each of the LED drivers may be linked to one of the sensor inputs to be actuated when a touch is detected. As well, each LED driver may be individually controlled via a host controller. The CAP1133 includes Multiple Pattern Touch recognition that allows the user to select a specific set of buttons to be touched simultaneously. If this pattern is detected, then a status bit is set and an interrupt generated. Features Deep Sleep is the lowest power state available, drawing 5uA (typical) of current. In this state, no sensor inputs are active. Communications will wake the device. Three (3) Capacitive Touch Sensor Inputs -- Programmable sensitivity -- Automatic recalibration -- Individual thresholds for each button Proximity Detection Multiple Button Pattern Detection Calibrates for Parasitic Capacitance Analog Filtering for System Noise Sources Press and Hold feature for Volume-like Applications SMBus / I2C Compliant Communication Interface Low Power Operation -- 5uA quiescent current in Deep Sleep -- 50uA quiescent current in Standby (1 sensor input monitored) -- Samples one or more channels in Standby Additionally, the CAP1133 includes circuitry and support for enhanced sensor proximity detection. The CAP1133 offers multiple power states operating at low quiescent currents. In the Standby state of operation, one or more capacitive touch sensor inputs are active and all LEDs may be used. Desktop and Notebook PCs LCD Monitors Consumer Electronics Appliances Three (3) LED Driver Outputs -- Open Drain or Push-Pull -- Programmable blink, breathe, and dimness controls -- Can be linked to Capacitive Touch Sensor inputs Available in 10-pin 3mm x 3mm RoHS compliant DFN package 1. SMSC, the SMSC logo and RightTouch are registered trademarks and the RightTouch logo is a trademark of Standard Microsystems Corporation ("SMSC"). Block Diagram LED1 LED2 LED3 VDD GND SMCLK LED Driver, Breathe, and Dimness control Capacitive Touch Sensing Algorithm SMBus Slave Protocol SMDATA ALERT# CS1 SMSC CAP1133 CS2 CS3 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Ordering Information: ORDERING NUMBER CAP1133-1-AIA-TR PACKAGE 10-pin DFN 3mm x 3mm (Lead-free RoHS compliant) FEATURES Three capacitive touch sensor inputs, Three LED drivers, SMBus interface Reel size is 4,000 pieces This product meets the halogen maximum concentration values per IEC61249-2-21 For RoHS compliance and environmental information, please visit www.smsc.com/rohs Please contact your SMSC sales representative for additional documentation related to this product such as application notes, anomaly sheets, and design guidelines. Copyright (c) 2012 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office to obtain the latest specifications before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor devices any licenses under any patent rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC's website at http://www.smsc.com. SMSC is a registered trademark of Standard Microsystems Corporation ("SMSC"). Product names and company names are the trademarks of their respective holders. The Microchip name and logo, and the Microchip logo are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT; TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Revision 1.32 (01-05-12) 2 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table of Contents Chapter 1 Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Chapter 2 Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Chapter 3 Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.1 3.2 3.3 3.4 Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Management Bus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2.1 SMBus Start Bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2.2 SMBus Address and RD / WR Bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2.3 SMBus Data Bytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2.4 SMBus ACK and NACK Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2.5 SMBus Stop Bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2.6 SMBus Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2.7 SMBus and I2C Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SMBus Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3.1 SMBus Write Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3.2 SMBus Read Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3.3 SMBus Send Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3.4 SMBus Receive Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I2C Protocols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.4.1 Block Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.4.2 Block Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 14 14 14 14 15 15 15 15 15 16 16 16 16 17 17 17 Chapter 4 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 4.1 4.2 4.3 4.4 Power States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.1 Linking LEDs to Capacitive Touch Sensor Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Capacitive Touch Sensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.1 Sensing Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.2 Recalibrating Sensor Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.3 Proximity Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.4 Multiple Touch Pattern Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.5 Low Frequency Noise Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.6 RF Noise Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ALERT# Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.1 Sensor Interrupt Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 19 19 19 20 20 21 21 21 21 21 21 Chapter 5 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 5.1 5.2 5.3 5.4 5.5 5.6 5.7 Main Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2.1 General Status - 02h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2.2 Sensor Input Status - 03h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2.3 LED Status - 04h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Noise Flag Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Delta Count Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensitivity Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.6.1 Configuration - 20h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.6.2 Configuration 2 - 44h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Enable Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SMSC CAP1133 3 DATASHEET 26 27 27 27 28 28 29 29 31 31 31 32 Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet 5.8 5.9 5.10 5.11 5.12 5.13 5.14 5.15 5.16 5.17 5.18 5.19 5.20 5.21 5.22 5.23 5.24 5.25 5.26 5.27 5.28 5.29 5.30 5.31 5.32 5.33 5.34 5.35 5.36 5.37 5.38 5.39 5.40 5.41 5.42 Sensor Input Configuration Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Configuration 2 Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Averaging and Sampling Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Calibration Activate Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interrupt Enable Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Repeat Rate Enable Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multiple Touch Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multiple Touch Pattern Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multiple Touch Pattern Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recalibration Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Threshold Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Noise Threshold Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standby Channel Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standby Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standby Sensitivity Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standby Threshold Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Base Count Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Output Type Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input LED Linking Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Polarity Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Output Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Linked LED Transition Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Mirror Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Behavior Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Pulse 1 Period Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Pulse 2 Period Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Breathe Period Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Duty Cycle Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Direct Ramp Rates Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Off Delay Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Calibration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manufacturer ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Revision Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 35 36 37 38 38 39 39 41 41 43 43 44 44 46 47 47 48 48 49 50 51 52 52 54 56 57 57 58 59 60 64 64 64 64 Chapter 6 Package Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 6.1 6.2 CAP1133 Package Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Package Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Appendix A Device Delta . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 A.1 Delta from CAP1033 to CAP1133 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Chapter 7 Datasheet Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Revision 1.32 (01-05-12) 4 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet List of Figures Figure 1.1 Figure 3.1 Figure 4.1 Figure 4.2 Figure 4.3 Figure 5.1 Figure 5.2 Figure 5.3 Figure 5.4 Figure 5.5 Figure 5.6 Figure 5.7 Figure 5.8 Figure 6.1 Figure 6.2 Figure 6.3 Figure 6.4 SMSC CAP1133 CAP1133 Pin Diagram (10-Pin DFN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 SMBus Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 System Diagram for CAP1133 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Sensor Interrupt Behavior - Repeat Rate Enabled. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Sensor Interrupt Behavior - No Repeat Rate Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Pulse 1 Behavior with Non-Inverted Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Pulse 1 Behavior with Inverted Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Pulse 2 Behavior with Non-Inverted Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Pulse 2 Behavior with Inverted Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Breathe Behavior with Non-Inverted Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Breathe Behavior with Inverted Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Direct Behavior for Non-Inverted Polarity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Direct Behavior for Inverted Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 10-Pin DFN 3mm x 3mm Package Drawings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 10-Pin DFN 3mm x 3mm Package Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 10-Pin DFN 3mm x 3mm PCB Footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 CAP1133 Package Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 5 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet List of Tables Table 1.1 Table 1.2 Table 2.1 Table 2.2 Table 3.1 Table 3.2 Table 3.3 Table 3.4 Table 3.5 Table 3.6 Table 3.7 Table 5.1 Table 5.2 Table 5.3 Table 5.4 Table 5.5 Table 5.6 Table 5.7 Table 5.8 Table 5.9 Table 5.10 Table 5.11 Table 5.12 Table 5.13 Table 5.14 Table 5.15 Table 5.16 Table 5.17 Table 5.18 Table 5.19 Table 5.20 Table 5.21 Table 5.22 Table 5.23 Table 5.24 Table 5.25 Table 5.26 Table 5.27 Table 5.28 Table 5.29 Table 5.30 Table 5.31 Table 5.32 Table 5.33 Table 5.34 Table 5.35 Table 5.36 Table 5.37 Table 5.38 Table 5.39 Table 5.40 Table 5.41 Pin Description for CAP1133. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Pin Types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Absolute Maximum Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Electrical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Protocol Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Write Byte Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Read Byte Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Send Byte Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Receive Byte Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Block Write Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Block Read Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Register Set in Hexadecimal Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Main Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 GAIN Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Noise Flag Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Sensor Input Delta Count Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Sensitivity Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 DELTA_SENSE Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 BASE_SHIFT Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Sensor Input Enable Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Sensor Input Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 MAX_DUR Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 RPT_RATE Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Sensor Input Configuration 2 Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 M_PRESS Bit Decode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Averaging and Sampling Configuration Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 AVG Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 SAMP_TIME Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 CYCLE_TIME Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Calibration Activate Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Interrupt Enable Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Repeat Rate Enable Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Multiple Touch Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 B_MULT_T Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Multiple Touch Pattern Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 MTP_TH Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Multiple Touch Pattern Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Recalibration Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 NEG_DELTA_CNT Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 CAL_CFG Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Sensor Input Threshold Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Sensor Input Noise Threshold Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 CSx_BN_TH Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Standby Channel Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Standby Configuration Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 STBY_AVG Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 STBY_SAMP_TIME Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 STBY_CY_TIME Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Standby Sensitivity Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 STBY_SENSE Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Revision 1.32 (01-05-12) 6 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table 5.42 Table 5.43 Table 5.44 Table 5.45 Table 5.46 Table 5.47 Table 5.48 Table 5.49 Table 5.50 Table 5.51 Table 5.52 Table 5.53 Table 5.54 Table 5.55 Table 5.56 Table 5.57 Table 5.58 Table 5.59 Table 5.60 Table 5.61 Table 5.62 Table 5.63 Table 5.64 Table 5.65 Table 5.66 Table 5.67 Table 5.68 Table 5.69 Table A.1 Table 7.1 SMSC CAP1133 Standby Threshold Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Base Count Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Output Type Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input LED Linking Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Polarity Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Output Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Polarity Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Linked LED Transition Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Mirror Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Behavior Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LEDx_CTL Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Pulse 1 Period Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Pulse / Breathe Period Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Pulse 2 Period Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Breathe Period Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Configuration Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PULSEX_CNT Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Duty Cycle Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Duty Cycle Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Direct Ramp Rates Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rise / Fall Rate Decode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Off Delay Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Breathe Off Delay Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Off Delay Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Calibration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vendor ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Revision Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Register Delta From CAP1033 to CAP1133 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Customer Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 DATASHEET 47 47 48 48 49 50 50 51 52 52 53 54 55 56 57 57 58 58 59 59 60 60 62 63 64 64 64 64 68 70 Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Chapter 1 Pin Description CAP1133 3mm x 3mm DFN ALERT# 1 10 CS1 SMDATA 2 9 CS2 SMCLK 3 8 CS3 VDD 4 7 LED3 LED1 5 6 LED2 GND Figure 1.1 CAP1133 Pin Diagram (10-Pin DFN) Table 1.1 Pin Description for CAP1133 PIN NUMBER 1 PIN NAME UNUSED CONNECTION PIN FUNCTION PIN TYPE Active low alert / interrupt output usable for SMBus alert OD (5V) Connect to Ground Active high alert / interrupt output usable for SMBus alert DO leave open ALERT# 2 SMDATA Bi-directional, open-drain SMBus data - requires pull-up DIOD (5V) 3 SMCLK SMBus clock input - requires pull-up resistor DI (5V) 4 VDD Positive Power supply Power n/a Open drain LED 1 driver (default) OD (5V) Connect to Ground Push-pull LED 1 driver DO leave open or connect to Ground Open drain LED 2 driver (default) OD (5V) Connect to Ground Push-pull LED 2 driver DO leave open or connect to Ground n/a 5 6 LED1 LED2 Revision 1.32 (01-05-12) 8 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table 1.1 Pin Description for CAP1133 (continued) PIN NUMBER PIN NAME 7 UNUSED CONNECTION PIN FUNCTION PIN TYPE Open drain LED 3 driver (default) OD (5V) Connect to Ground Push-pull LED 3 driver DO leave open or connect to Ground LED3 8 CS3 Capacitive Touch Sensor Input 3 AIO Connect to Ground 9 CS2 Capacitive Touch Sensor Input 2 AIO Connect to Ground 10 CS1 Capacitive Touch Sensor Input 1 AIO Connect to Ground Bottom Pad GND Ground Power n/a APPLICATION NOTE: When the ALERT# pin is configured as an active low output, it will be open drain. When it is configured as an active high output, it will be push-pull. APPLICATION NOTE: For the 5V tolerant pins that have a pull-up resistor, the pull-up voltage must not exceed 3.6V when the CAP1133 is unpowered. The pin types are described in Table 1.2. All pins labeled with (5V) are 5V tolerant. Table 1.2 Pin Types PIN TYPE Power DI AIO DESCRIPTION This pin is used to supply power or ground to the device. Digital Input - This pin is used as a digital input. This pin is 5V tolerant. Analog Input / Output -This pin is used as an I/O for analog signals. DIOD Digital Input / Open Drain Output - This pin is used as a digital I/O. When it is used as an output, it is open drain and requires a pull-up resistor. This pin is 5V tolerant. OD Open Drain Digital Output - This pin is used as a digital output. It is open drain and requires a pull-up resistor. This pin is 5V tolerant. DO Push-pull Digital Output - This pin is used as a digital output and can sink and source current. DIO Push-pull Digital Input / Output - This pin is used as an I/O for digital signals. SMSC CAP1133 9 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Chapter 2 Electrical Specifications Table 2.1 Absolute Maximum Ratings Voltage on 5V tolerant pins (V5VT_PIN) -0.3 to 5.5 V Voltage on 5V tolerant pins (|V5VT_PIN - VDD|) Note 2.2 0 to 3.6 V Voltage on VDD pin -0.3 to 4 V Voltage on any other pin to GND -0.3 to VDD + 0.3 V Package Power Dissipation up to TA = 85C for 10 pin DFN (see Note 2.3) 0.7 W Junction to Ambient (JA) 77.7 C/W Operating Ambient Temperature Range -40 to 125 C Storage Temperature Range -55 to 150 C ESD Rating, All Pins, HBM 8000 V Note 2.1 Stresses above those listed could cause permanent damage to the device. This is a stress rating only and functional operation of the device at any other condition above those indicated in the operation sections of this specification is not implied. Note 2.2 For the 5V tolerant pins that have a pull-up resistor, the voltage difference between V5VT_PIN and VDD must never exceed 3.6V. Note 2.3 The Package Power Dissipation specification assumes a recommended thermal via design consisting of a 2x2 matrix of 0.3mm (12mil) vias at 1.0mm pitch connected to the ground plane with a 1.6 x 2.3mm thermal landing. Table 2.2 Electrical Specifications VDD = 3V to 3.6V, TA = 0C to 85C, all Typical values at TA = 27C unless otherwise noted. CHARACTERISTIC SYMBOL MIN TYP MAX UNIT CONDITIONS DC Power Supply Voltage Revision 1.32 (01-05-12) VDD 3.0 3.3 3.6 10 DATASHEET V SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table 2.2 Electrical Specifications (continued) VDD = 3V to 3.6V, TA = 0C to 85C, all Typical values at TA = 27C unless otherwise noted. CHARACTERISTIC SYMBOL MIN TYP MAX UNIT CONDITIONS uA Standby state active 1 sensor input monitored No LEDs active Default conditions (8 avg, 70ms cycle time) uA Standby state active 1 sensor input monitored No LEDs active 1 avg, 140ms cycle time, Supply Current 120 ISTBY ISTBY 170 50 IDSLEEP 5 15 uA Deep Sleep state active LEDs at 100% or 0% Duty Cycle No communications TA < 40C 3.135 < VDD < 3.465V IDD 500 600 uA Capacitive Sensing Active No LEDs active Capacitive Touch Sensor Inputs Maximum Base Capacitance CBASE Minimum Detectable Capacitive Shift CTOUCH 20 Recommended Cap Shift CTOUCH 0.1 Power Supply Rejection 50 PSR pF Pad untouched fF Pad touched - default conditions (1 avg, 35ms cycle time, 1x sensitivity) pF Pad touched - Not tested 10 counts /V Untouched Current Counts Base Capacitance 5pF - 50pF Maximum sensitivity Negative Delta Counts disabled All other parameters default 15 ms 200 ms 2 3 Timing Time to communications ready tCOMM_DLY Time to first conversion ready tCONV_DLY 170 LED Drivers Duty Cycle DUTYLED Drive Frequency fLED Sinking Current ISINK 24 mA VOL = 0.4 Sourcing Current ISOURCE 24 mA VOH = VDD - 0.4 SMSC CAP1133 0 100 2 % Programmable kHz 11 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table 2.2 Electrical Specifications (continued) VDD = 3V to 3.6V, TA = 0C to 85C, all Typical values at TA = 27C unless otherwise noted. CHARACTERISTIC Leakage Current SYMBOL MIN TYP MAX ILEAK UNIT CONDITIONS 5 uA powered or unpowered TA < 85C pull-up voltage < 3.6V if unpowered 0.4 V ISINK_IO = 8mA ISOURCE_IO = 8mA I/O Pins Output Low Voltage VOL Output High Voltage VOH VDD 0.4 V Input High Voltage VIH 2.0 V Input Low Voltage VIL 0.8 V Leakage Current ILEAK 5 uA powered or unpowered TA < 85C pull-up voltage < 3.6V if unpowered SMBus Timing Input Capacitance CIN Clock Frequency fSMB Spike Suppression tSP Bus Free Time Stop to Start tBUF 1.3 us Start Setup Time tSU:STA 0.6 us Start Hold Time tHD:STA 0.6 us Stop Setup Time tSU:STO 0.6 us Data Hold Time tHD:DAT 0 us When transmitting to the master Data Hold Time tHD:DAT 0.3 us When receiving from the master Data Setup Time tSU:DAT 0.6 us Clock Low Period tLOW 1.3 us Clock High Period tHIGH 0.6 us Clock / Data Fall Time tFALL 300 ns Min = 20+0.1CLOAD ns Clock / Data Rise Time tRISE 300 ns Min = 20+0.1CLOAD ns Capacitive Load CLOAD 400 pF per bus line Note 2.4 Revision 1.32 (01-05-12) 5 pF 10 400 kHz 50 ns The ALERT pin will not glitch high or low at power up if connected to VDD or another voltage. 12 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Note 2.5 SMSC CAP1133 The SMCLK and SMDATA pins will not glitch low at power up if connected to VDD or another voltage. 13 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Chapter 3 Communications 3.1 Communications The CAP1133 communicates using the SMBus or I2C protocol. The CAP1133 supports the following protocols: Send Byte, Receive Byte, Read Byte, Write Byte, Read Block, and Write Block. In addition, the device supports I2C formatting for block read and block write protocols. 3.2 System Management Bus The CAP1133 communicates with a host controller, such as an SMSC SIO, through the SMBus. The SMBus is a two-wire serial communication protocol between a computer host and its peripheral devices. A detailed timing diagram is shown in Figure 3.1. Stretching of the SMCLK signal is supported; however, the CAP1133 will not stretch the clock signal. TLOW THIGH THD:STA TSU:STO TRISE SMCLK THD:STA TFALL THD:DAT TSU:STA TSU:DAT SMDATA TBUF P S S S - Start Condition P - Stop Condition P Figure 3.1 SMBus Timing Diagram 3.2.1 SMBus Start Bit The SMBus Start bit is defined as a transition of the SMBus Data line from a logic `1' state to a logic `0' state while the SMBus Clock line is in a logic `1' state. 3.2.2 SMBus Address and RD / WR Bit The SMBus Address Byte consists of the 7-bit client address followed by the RD / WR indicator bit. If this RD / WR bit is a logic `0', then the SMBus Host is writing data to the client device. If this RD / WR bit is a logic `1', then the SMBus Host is reading data from the client device. The CAP1133 responds to SMBus address 0101_000(r/w). 3.2.3 SMBus Data Bytes All SMBus Data bytes are sent most significant bit first and composed of 8-bits of information. Revision 1.32 (01-05-12) 14 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet 3.2.4 SMBus ACK and NACK Bits The SMBus client will acknowledge all data bytes that it receives. This is done by the client device pulling the SMBus Data line low after the 8th bit of each byte that is transmitted. This applies to both the Write Byte and Block Write protocols. The Host will NACK (not acknowledge) the last data byte to be received from the client by holding the SMBus data line high after the 8th data bit has been sent. For the Block Read protocol, the Host will ACK each data byte that it receives except the last data byte. 3.2.5 SMBus Stop Bit The SMBus Stop bit is defined as a transition of the SMBus Data line from a logic `0' state to a logic `1' state while the SMBus clock line is in a logic `1' state. When the CAP1133 detects an SMBus Stop bit and it has been communicating with the SMBus protocol, it will reset its client interface and prepare to receive further communications. 3.2.6 SMBus Timeout The CAP1133 includes an SMBus timeout feature. Following a 30ms period of inactivity on the SMBus where the SMCLK pin is held low, the device will timeout and reset the SMBus interface. The timeout function defaults to disabled. It can be enabled by setting the TIMEOUT bit in the Configuration register (see Section 5.6, "Configuration Registers"). 3.2.7 SMBus and I2C Compatibility The major differences between SMBus and I2C devices are highlighted here. For more information, refer to the SMBus 2.0 and I2C specifications. For information on using the CAP1133 in an I2C system, refer to SMSC AN 14.0 SMSC Dedicated Slave Devices in I2C Systems. 1. CAP1133 supports I2C fast mode at 400kHz. This covers the SMBus max time of 100kHz. 2. Minimum frequency for SMBus communications is 10kHz. 3. The SMBus client protocol will reset if the clock is held at a logic `0' for longer than 30ms. This timeout functionality is disabled by default in the CAP1133 and can be enabled by writing to the TIMEOUT bit. I2C does not have a timeout. 4. The SMBus client protocol will reset if both the clock and data lines are held at a logic `1' for longer than 200s (idle condition). This function is disabled by default in the CAP1133 and can be enabled by writing to the TIMEOUT bit. I2C does not have an idle condition. 5. I2C devices do not support the Alert Response Address functionality (which is optional for SMBus). 6. I2C devices support block read and write differently. I2C protocol allows for unlimited number of bytes to be sent in either direction. The SMBus protocol requires that an additional data byte indicating number of bytes to read / write is transmitted. The CAP1133 supports I2C formatting only. 3.3 SMBus Protocols The CAP1133 is SMBus 2.0 compatible and supports Write Byte, Read Byte, Send Byte, and Receive Byte as valid protocols as shown below. All of the below protocols use the convention in Table 3.1. SMSC CAP1133 15 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table 3.1 Protocol Format DATA SENT TO THE HOST DATA SENT TO DEVICE Data sent 3.3.1 Data sent SMBus Write Byte The Write Byte is used to write one byte of data to a specific register as shown in Table 3.2. Table 3.2 Write Byte Protocol START SLAVE ADDRESS WR ACK REGISTER ADDRESS ACK REGISTER DATA ACK STOP 1 ->0 0101_000 0 0 XXh 0 XXh 0 0 -> 1 3.3.2 SMBus Read Byte The Read Byte protocol is used to read one byte of data from the registers as shown in Table 3.3. Table 3.3 Read Byte Protocol START 1->0 SLAVE ADDRESS 0101_000 3.3.3 WR ACK REGISTER ADDRESS ACK START CLIENT ADDRESS 0 0 XXh 0 1 ->0 0101_000 RD 1 ACK 0 REGISTER DATA XXh NACK 1 STOP 0 -> 1 SMBus Send Byte The Send Byte protocol is used to set the internal address register pointer to the correct address location. No data is transferred during the Send Byte protocol as shown in Table 3.4. APPLICATION NOTE: The Send Byte protocol is not functional in Deep Sleep (i.e., DSLEEP bit is set). Table 3.4 Send Byte Protocol START SLAVE ADDRESS WR ACK REGISTER ADDRESS ACK STOP 1 -> 0 0101_000 0 0 XXh 0 0 -> 1 3.3.4 SMBus Receive Byte The Receive Byte protocol is used to read data from a register when the internal register address pointer is known to be at the right location (e.g., set via Send Byte). This is used for consecutive reads of the same register as shown in Table 3.5. APPLICATION NOTE: The Receive Byte protocol is not functional in Deep Sleep (i.e., DSLEEP bit is set). Revision 1.32 (01-05-12) 16 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table 3.5 Receive Byte Protocol START SLAVE ADDRESS RD ACK REGISTER DATA NACK STOP 1 -> 0 0101_000 1 0 XXh 1 0 -> 1 3.4 I2C Protocols The CAP1133 supports I2C Block Write and Block Read. The protocols listed below use the convention in Table 3.1. 3.4.1 Block Write The Block Write is used to write multiple data bytes to a group of contiguous registers as shown in Table 3.6. APPLICATION NOTE: When using the Block Write protocol, the internal address pointer will be automatically incremented after every data byte is received. It will wrap from FFh to 00h. Table 3.6 Block Write Protocol START SLAVE ADDRESS WR ACK REGISTER ADDRESS ACK REGISTER DATA ACK 1 ->0 0101_000 0 0 XXh 0 XXh 0 REGISTER DATA ACK REGISTER DATA ACK ... REGISTER DATA ACK STOP XXh 0 XXh 0 ... XXh 0 0 -> 1 3.4.2 Block Read The Block Read is used to read multiple data bytes from a group of contiguous registers as shown in Table 3.7. APPLICATION NOTE: When using the Block Read protocol, the internal address pointer will be automatically incremented after every data byte is received. It will wrap from FFh to 00h. Table 3.7 Block Read Protocol START SLAVE ADDRESS WR ACK REGISTER ADDRESS ACK START SLAVE ADDRESS RD ACK REGISTER DATA 1->0 0101_000 0 0 XXh 0 1 ->0 0101_000 1 0 XXh ACK REGISTER DATA ACK REGISTER DATA ACK REGISTER DATA ACK ... REGISTER DATA NACK STOP 0 XXh 0 XXh 0 XXh 0 ... XXh 1 0 -> 1 SMSC CAP1133 17 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Chapter 4 General Description The CAP1133 is a multiple channel Capacitive Touch sensor with multiple power LED drivers. It contains three (3) individual capacitive touch sensor inputs with programmable sensitivity for use in touch sensor applications. Each sensor input automatically recalibrates to compensate for gradual environmental changes. The CAP1133 also contains three (3) low side (or push-pull) LED drivers that offer full-on / off, variable rate blinking, dimness controls, and breathing. Each of the LED drivers may be linked to one of the sensor inputs to be actuated when a touch is detected. As well, each LED driver may be individually controlled via a host controller. The CAP1133 offers multiple power states. It operates at the lowest quiescent current during its Deep Sleep state. In the low power Standby state, it can monitor one or more channels and respond to communications normally. The device communicates with a host controller using SMBus / I2C. The host controller may poll the device for updated information at any time or it may configure the device to flag an interrupt whenever a touch is detected on any sensor pad. A typical system diagram is shown in Figure 4.1. VDD 3.3V - 5V ALERT# SMDATA SMCLK Embedded Controller Touch Button CS1 Touch Button CS2 LED2 Touch Button CS3 LED3 CAP1133 LED1 Figure 4.1 System Diagram for CAP1133 Revision 1.32 (01-05-12) 18 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet 4.1 Power States The CAP1133 has three operating states depending on the status of the STBY and DSLEEP bits. When the device transitions between power states, previously detected touches (for inactive channels) are cleared and the status bits reset. 1. Fully Active - The device is fully active. It is monitoring all active capacitive sensor inputs and driving all LED channels as defined. 2. Standby - The device is in a lower power state. It will measure a programmable number of channels using the Standby Configuration controls (see Section 5.20 through Section 5.22). Interrupts will still be generated based on the active channels. The device will still respond to communications normally and can be returned to the Fully Active state of operation by clearing the STBY bit. 3. Deep Sleep - The device is in its lowest power state. It is not monitoring any capacitive sensor inputs and not driving any LEDs. All LEDs will be driven to their programmed non-actuated state and no PWM operations will be done. While in Deep Sleep, the device can be awakened by SMBus communications targeting the device. This will not cause the DSLEEP to be cleared so the device will return to Deep Sleep once all communications have stopped. APPLICATION NOTE: In the Deep Sleep state, the LED output will be either high or low and will not be PWM'd at the min or max duty cycle. 4.2 LED Drivers The CAP1133 contains three (3) LED drivers. Each LED driver can be linked to its respective capacitive touch sensor input or it can be controlled by the host. Each LED driver can be configured to operate in one of the following modes with either push-pull or open drain drive. 1. Direct - The LED is configured to be on or off when the corresponding input stimulus is on or off (or inverted). The brightness of the LED can be programmed from full off to full on (default). Additionally, the LED contains controls to individually configure ramping on, off, and turn-off delay. 2. Pulse 1 - The LED is configured to "Pulse" (transition ON-OFF-ON) a programmable number of times with programmable rate and min / max brightness. This behavior may be actuated when a press is detected or when a release is detected. 3. Pulse 2 - The LED is configured to "Pulse" while actuated and then "Pulse" a programmable number of times with programmable rate and min / max brightness when the sensor pad is released. 4. Breathe - The LED is configured to transition continuously ON-OFF-ON (i.e. to "Breathe") with a programmable rate and min / max brightness. When an LED is not linked to a sensor and is actuated by the host, there's an option to assert the ALERT# pin when the initiated LED behavior has completed. 4.2.1 Linking LEDs to Capacitive Touch Sensor Inputs All LEDs can be linked to the corresponding capacitive touch sensor input so that when the sensor input detects a touch, the corresponding LED will be actuated at one of the programmed responses. 4.3 Capacitive Touch Sensing The CAP1133 contains three (3) independent capacitive touch sensor inputs. Each sensor input has dynamic range to detect a change of capacitance due to a touch. Additionally, each sensor input can be configured to be automatically and routinely re-calibrated. SMSC CAP1133 19 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet 4.3.1 Sensing Cycle Each capacitive touch sensor input has controls to be activated and included in the sensing cycle. When the device is active, it automatically initiates a sensing cycle and repeats the cycle every time it finishes. The cycle polls through each active sensor input starting with CS1 and extending through CS3. As each capacitive touch sensor input is polled, its measurement is compared against a baseline "Not Touched" measurement. If the delta measurement is large enough, a touch is detected and an interrupt is generated. The sensing cycle time is programmable (see Section 5.10, "Averaging and Sampling Configuration Register"). 4.3.2 Recalibrating Sensor Inputs There are various options for recalibrating the capacitive touch sensor inputs. Recalibration re-sets the Base Count Registers (Section 5.24, "Sensor Input Base Count Registers") which contain the "not touched" values used for touch detection comparisons. APPLICATION NOTE: The device will recalibrate all sensor inputs that were disabled when it transitions from Standby. Likewise, the device will recalibrate all sensor inputs when waking out of Deep Sleep. 4.3.2.1 Manual Recalibration The Calibration Activate Registers (Section 5.11, "Calibration Activate Register") force recalibration of selected sensor inputs. When a bit is set, the corresponding capacitive touch sensor input will be recalibrated (both analog and digital). The bit is automatically cleared once the recalibration routine has finished. Note: During this recalibration routine, the sensor inputs will not detect a press for up to 200ms and the Sensor Base Count Register values will be invalid. In addition, any press on the corresponding sensor pads will invalidate the recalibration. 4.3.2.2 Automatic Recalibration Each sensor input is regularly recalibrated at a programmable rate (see Section 5.17, "Recalibration Configuration Register"). By default, the recalibration routine stores the average 64 previous measurements and periodically updates the base "not touched" setting for the capacitive touch sensor input. Note: Automatic recalibration only works when the delta count is below the active sensor input threshold. It is disabled when a touch is detected. 4.3.2.3 Negative Delta Count Recalibration It is possible that the device loses sensitivity to a touch. This may happen as a result of a noisy environment, an accidental recalibration during a touch, or other environmental changes. When this occurs, the base untouched sensor input may generate negative delta count values. The NEG_DELTA_CNT bits (see Section 5.17, "Recalibration Configuration Register") can be set to force a recalibration after a specified number of consecutive negative delta readings. Note: During this recalibration, the device will not respond to touches. 4.3.2.4 Delayed Recalibration It is possible that a "stuck button" occurs when something is placed on a button which causes a touch to be detected for a long period. By setting the MAX_DUR_EN bit (see Section 5.6, "Configuration Registers"), a recalibration can be forced when a touch is held on a button for longer than the duration specified in the MAX_DUR bits (see Section 5.8, "Sensor Input Configuration Register"). Revision 1.32 (01-05-12) 20 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Note: Delayed recalibration only works when the delta count is above the active sensor input threshold. If enabled, it is invoked when a sensor pad touch is held longer than the MAX_DUR bit setting. 4.3.3 Proximity Detection Each sensor input can be configured to detect changes in capacitance due to proximity of a touch. This circuitry detects the change of capacitance that is generated as an object approaches, but does not physically touch, the enabled sensor pad(s). When a sensor input is selected to perform proximity detection, it will be sampled from 1x to 128x per sampling cycle. The larger the number of samples that are taken, the greater the range of proximity detection is available at the cost of an increased overall sampling time. 4.3.4 Multiple Touch Pattern Detection The multiple touch pattern (MTP) detection circuitry can be used to detect lid closure or other similar events. An event can be flagged based on either a minimum number of sensor inputs or on specific sensor inputs simultaneously exceeding an MTP threshold or having their Noise Flag Status Register bits set. An interrupt can also be generated. During an MTP event, all touches are blocked (see Section 5.15, "Multiple Touch Pattern Configuration Register"). 4.3.5 Low Frequency Noise Detection Each sensor input has an EMI noise detector that will sense if low frequency noise is injected onto the input with sufficient power to corrupt the readings. If this occurs, the device will reject the corrupted sample and set the corresponding bit in the Noise Status register to a logic `1'. 4.3.6 RF Noise Detection Each sensor input contains an integrated RF noise detector. This block will detect injected RF noise on the CS pin. The detector threshold is dependent upon the noise frequency. If RF noise is detected on a CS line, that sample is removed and not compared against the threshold. 4.4 ALERT# Pin The ALERT# pin is an active low (or active high when configured) output that is driven when an interrupt event is detected. Whenever an interrupt is generated, the INT bit (see Section 5.1, "Main Control Register") is set. The ALERT# pin is cleared when the INT bit is cleared by the user. Additionally, when the INT bit is cleared by the user, status bits are only cleared if no touch is detected. 4.4.1 Sensor Interrupt Behavior The sensor interrupts are generated in one of two ways: 1. An interrupt is generated when a touch is detected and, as a user selectable option, when a release is detected (by default - see Section 5.6). See Figure 4.3. 2. If the repeat rate is enabled then, so long as the touch is held, another interrupt will be generated based on the programmed repeat rate (see Figure 4.2). When the repeat rate is enabled, the device uses an additional control called MPRESS that determines whether a touch is flagged as a simple "touch" or a "press and hold". The MPRESS[3:0] bits set a minimum press timer. When the button is touched, the timer begins. If the sensor pad is released before the minimum press timer expires, it is flagged as a touch and an interrupt is generated upon release. If the sensor input detects a touch for longer than this timer value, it is flagged as a "press SMSC CAP1133 21 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet and hold" event. So long as the touch is held, interrupts will be generated at the programmed repeat rate and upon release (if enabled). APPLICATION NOTE: Figure 4.2 and Figure 4.3 show default operation which is to generate an interrupt upon sensor pad release and an active-low ALERT# pin. APPLICATION NOTE: The host may need to poll the device twice to determine that a release has been detected. Interrupt on Touch Polling Cycle (35ms) Min Press Setting (280ms) Touch Detected Button Repeat Rate (175ms) Interrupt on Release (optional) Button Repeat Rate (175ms) INT bit ALERT# pin (active low) Button Status Write to INT bit Figure 4.2 Sensor Interrupt Behavior - Repeat Rate Enabled Interrupt on Touch Polling Cycle (35ms) Interrupt on Release (optional) Touch Detected INT bit ALERT# pin (active low) Button Status Write to INT bit Figure 4.3 Sensor Interrupt Behavior - No Repeat Rate Enabled Revision 1.32 (01-05-12) 22 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Chapter 5 Register Description The registers shown in Table 5.1 are accessible through the communications protocol. An entry of `-' indicates that the bit is not used and will always read `0'. Table 5.1 Register Set in Hexadecimal Order REGISTER ADDRESS R/W REGISTER NAME FUNCTION DEFAULT VALUE PAGE 00h R/W Main Control Controls general power states and power dissipation 00h Page 26 02h R General Status Stores general status bits 00h Page 27 03h R Sensor Input Status Returns the state of the sampled capacitive touch sensor inputs 00h Page 27 04h R LED Status Stores status bits for LEDs 00h Page 27 0Ah R Noise Flag Status Stores the noise flags for sensor inputs 00h Page 28 10h R Sensor Input 1 Delta Count Stores the delta count for CS1 00h Page 29 11h R Sensor Input 2 Delta Count Stores the delta count for CS2 00h Page 29 12h R Sensor Input 3 Delta Count Stores the delta count for CS3 00h Page 29 1Fh R/W Sensitivity Control Controls the sensitivity of the threshold and delta counts and data scaling of the base counts 2Fh Page 29 20h R/W Configuration Controls general functionality 20h Page 31 21h R/W Sensor Input Enable Controls whether the capacitive touch sensor inputs are sampled 07h Page 32 22h R/W Sensor Input Configuration Controls max duration and autorepeat delay for sensor inputs operating in the full power state A4h Page 33 23h R/W Sensor Input Configuration 2 Controls the MPRESS controls for all sensor inputs 07h Page 35 24h R/W Averaging and Sampling Config Controls averaging and sampling window 39h Page 36 26h R/W Calibration Activate Forces re-calibration for capacitive touch sensor inputs 00h Page 37 27h R/W Interrupt Enable Enables Interrupts associated with capacitive touch sensor inputs 07h Page 38 28h R/W Repeat Rate Enable Enables repeat rate for all sensor inputs 07h Page 38 SMSC CAP1133 23 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table 5.1 Register Set in Hexadecimal Order (continued) REGISTER ADDRESS R/W REGISTER NAME FUNCTION DEFAULT VALUE PAGE 2Ah R/W Multiple Touch Configuration Determines the number of simultaneous touches to flag a multiple touch condition 80h Page 39 2Bh R/W Multiple Touch Pattern Configuration Determines the multiple touch pattern (MTP) configuration 00h Page 39 2Dh R/W Multiple Touch Pattern Determines the pattern or number of sensor inputs used by the MTP circuitry 07h Page 41 2Fh R/W Recalibration Configuration Determines re-calibration timing and sampling window 8Ah Page 41 30h R/W Sensor Input 1 Threshold Stores the delta count threshold to determine a touch for Capacitive Touch Sensor Input 1 40h Page 43 31h R/W Sensor Input 2 Threshold Stores the delta count threshold to determine a touch for Capacitive Touch Sensor Input 2 40h Page 43 32h R/W Sensor Input 3 Threshold Stores the delta count threshold to determine a touch for Capacitive Touch Sensor Input 3 40h Page 43 38h R/W Sensor Input Noise Threshold Stores controls for selecting the noise threshold for all sensor inputs 01h Page 43 Standby Configuration Registers 40h R/W Standby Channel Controls which sensor inputs are enabled while in standby 00h Page 44 41h R/W Standby Configuration Controls averaging and cycle time while in standby 39h Page 44 42h R/W Standby Sensitivity Controls sensitivity settings used while in standby 02h Page 46 43h R/W Standby Threshold Stores the touch detection threshold for active sensor inputs in standby 40h Page 47 44h R/W Configuration 2 Stores additional configuration controls for the device 40h Page 31 Base Count Registers 50h R Sensor Input 1 Base Count Stores the reference count value for sensor input 1 C8h Page 47 51h R Sensor Input 2 Base Count Stores the reference count value for sensor input 2 C8h Page 47 52h R Sensor Input 3 Base Count Stores the reference count value for sensor input 3 C8h Page 47 00h Page 48 LED Controls 71h R/W Revision 1.32 (01-05-12) LED Output Type Controls the output type for the LED outputs 24 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table 5.1 Register Set in Hexadecimal Order (continued) REGISTER ADDRESS R/W REGISTER NAME FUNCTION DEFAULT VALUE PAGE 72h R/W Sensor Input LED Linking Controls linking of sensor inputs to LED channels 00h Page 48 73h R/W LED Polarity Controls the output polarity of LEDs 00h Page 49 74h R/W LED Output Control Controls the output state of the LEDs 00h Page 50 77h R/W LED Linked Transition Control Controls the transition when LEDs are linked to CS channels 00h Page 51 79h R/W LED Mirror Control Controls the mirroring of duty cycles for the LEDs 00h Page 52 81h R/W LED Behavior 1 Controls the behavior and response of LEDs 1 - 3 00h Page 52 84h R/W LED Pulse 1 Period Controls the period of each breathe during a pulse 20h Page 54 85h R/W LED Pulse 2 Period Controls the period of the breathing during breathe and pulse operation 14h Page 56 86h R/W LED Breathe Period Controls the period of an LED breathe operation 5Dh Page 57 88h R/W LED Config Controls LED configuration 04h Page 57 90h R/W LED Pulse 1 Duty Cycle Determines the min and max duty cycle for the pulse operation F0h Page 58 91h R/W LED Pulse 2 Duty Cycle Determines the min and max duty cycle for breathe and pulse operation F0h Page 58 92h R/W LED Breathe Duty Cycle Determines the min and max duty cycle for the breathe operation F0h Page 58 93h R/W LED Direct Duty Cycle Determines the min and max duty cycle for Direct mode LED operation F0h Page 58 94h R/W LED Direct Ramp Rates Determines the rising and falling edge ramp rates of the LEDs 00h Page 59 95h R/W LED Off Delay Determines the off delay for all LED behaviors 00h Page 60 R Sensor Input 1 Calibration Stores the upper 8-bit calibration value for sensor input 1 00h Page 64 R Sensor Input 2 Calibration Stores the upper 8-bit calibration value for sensor input 2 00h Page 64 R Sensor Input 3 Calibration Stores the upper 8-bit calibration value for sensor input 3 00h Page 64 R Sensor Input Calibration LSB 1 Stores the 2 LSBs of the calibration value for sensor inputs 1 - 3 00h Page 64 R Product ID Stores a fixed value that identifies each product 54h Page 64 B1h B2h B3h B9h FDh SMSC CAP1133 25 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table 5.1 Register Set in Hexadecimal Order (continued) REGISTER ADDRESS R/W REGISTER NAME FUNCTION DEFAULT VALUE PAGE FEh R Manufacturer ID Stores a fixed value that identifies SMSC 5Dh Page 64 FFh R Revision Stores a fixed value that represents the revision number 83h Page 64 During Power-On-Reset (POR), the default values are stored in the registers. A POR is initiated when power is first applied to the part and the voltage on the VDD supply surpasses the POR level as specified in the electrical characteristics. Any reads to undefined registers will return 00h. Writes to undefined registers will not have an effect. When a bit is "set", this means that the user writes a logic `1' to it. When a bit is "cleared", this means that the user writes a logic `0' to it. 5.1 Main Control Register Table 5.2 Main Control Register ADDR R/W REGISTER 00h R/W Main Control B7 B6 GAIN[1:0] B5 B4 B3 B2 B1 B0 DEFAULT STBY DSLEEP - - - INT 00h The Main Control register controls the primary power state of the device. Bits 7 - 6 - GAIN[1:0] - Controls the gain used by the capacitive touch sensing circuitry. As the gain is increased, the effective sensitivity is likewise increased as a smaller delta capacitance is required to generate the same delta count values. The sensitivity settings may need to be adjusted along with the gain settings such that data overflow does not occur. APPLICATION NOTE: The gain settings apply to both Standby and Active states. Table 5.3 GAIN Bit Decode GAIN[1:0] 1 0 CAPACITIVE TOUCH SENSOR GAIN 0 0 1 0 1 2 1 0 4 1 1 8 Bit 5 - STBY - Enables Standby. `0' (default) - Sensor input scanning is active and LEDs are functional. `1' - Capacitive touch sensor input scanning is limited to the sensor inputs set in the Standby Channel register (see Section 5.20). The status registers will not be cleared until read. LEDs that are linked to capacitive touch sensor inputs will remain linked and active. Sensor inputs that are Revision 1.32 (01-05-12) 26 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet no longer sampled will flag a release and then remain in a non-touched state. LEDs that are manually controlled will be unaffected. Bit 4 - DSLEEP - Enables Deep Sleep by deactivating all functions. `0' (default) - Sensor input scanning is active and LEDs are functional. `1' - All sensor input scanning is disabled. All LEDs are driven to their programmed non-actuated state and no PWM operations will be done. The status registers are automatically cleared and the INT bit is cleared. Bit 0 - INT - Indicates that there is an interrupt. When this bit is set, it asserts the ALERT# pin. If a channel detects a touch and its associated interrupt enable bit is not set to a logic `1', no action is taken. This bit is cleared by writing a logic `0' to it. When this bit is cleared, the ALERT# pin will be deasserted and all status registers will be cleared if the condition has been removed. 5.2 `0' - No interrupt pending. `1' - A touch has been detected on one or more channels and the interrupt has been asserted. Status Registers Table 5.4 Status Registers ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 02h R General Status - - - LED - MULT MTP TOUCH 00h 03h R Sensor Input Status - - - - - CS3 CS2 CS1 00h 04h R LED Status - - - - - LED3_ DN LED2_ DN LED1_ DN 00h All status bits are cleared when the device enters the Deep Sleep (DSLEEP = `1' - see Section 5.1). 5.2.1 General Status - 02h Bit 4 - LED - Indicates that one or more LEDs have finished their programmed activity. This bit is set if any bit in the LED Status register is set. Bit 2 - MULT - Indicates that the device is blocking detected touches due to the Multiple Touch detection circuitry (see Section 5.14). This bit will not cause the INT bit to be set and hence will not cause an interrupt. Bit 1 - MTP - Indicates that the device has detected a number of sensor inputs that exceed the MTP threshold either via the pattern recognition or via the number of sensor inputs (see Section 5.15). This bit will cause the INT bit to be set if the MTP_ALERT bit is also set. This bit will not be cleared until the condition that caused it to be set has been removed. Bit 0 - TOUCH - Indicates that a touch was detected. This bit is set if any bit in the Sensor Input Status register is set. 5.2.2 Sensor Input Status - 03h The Sensor Input Status Register stores status bits that indicate a touch has been detected. A value of `0' in any bit indicates that no touch has been detected. A value of `1' in any bit indicates that a touch has been detected. SMSC CAP1133 27 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet All bits are cleared when the INT bit is cleared and if a touch on the respective capacitive touch sensor input is no longer present. If a touch is still detected, the bits will not be cleared (but this will not cause the interrupt to be asserted - see Section 5.6). Bit 2 - CS3 - Indicates that a touch was detected on Sensor Input 3. This sensor input can be linked to LED3. Bit 1 - CS2 - Indicates that a touch was detected on Sensor Input 2. This sensor input can be linked to LED2. Bit 0 - CS1 - Indicates that a touch was detected on Sensor Input 1. This sensor input can be linked to LED1. 5.2.3 LED Status - 04h The LED Status Registers indicate when an LED has completed its configured behavior (see Section 5.31, "LED Behavior Register") after being actuated by the host (see Section 5.28, "LED Output Control Register"). These bits are ignored when the LED is linked to a capacitive sensor input. All LED Status bits are cleared when the INT bit is cleared. Bit 2 - LED3_DN - Indicates that LED3 has finished its behavior after being actuated by the host. Bit 1 - LED2_DN - Indicates that LED2 has finished its behavior after being actuated by the host. Bit 0 - LED1_DN - Indicates that LED1 has finished its behavior after being actuated by the host. 5.3 Noise Flag Status Registers Table 5.5 Noise Flag Status Registers ADDR R/W REGISTER 0Ah R Noise Flag Status B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT - - - CS3_ NOISE CS2_ NOISE CS1_ NOISE 00h The Noise Flag Status registers store status bits that are generated from the analog block if the detected noise is above the operating region of the analog detector or the RF noise detector. These bits indicate that the most recently received data from the sensor input is invalid and should not be used for touch detection. So long as the bit is set for a particular channel, the delta count value is reset to 00h and thus no touch is detected. These bits are not sticky and will be cleared automatically if the analog block does not report a noise error. APPLICATION NOTE: If the MTP detection circuitry is enabled, these bits count as sensor inputs above the MTP threshold (see Section 4.3.4, "Multiple Touch Pattern Detection") even if the corresponding delta count is not. If the corresponding delta count also exceeds the MTP threshold, it is not counted twice. APPLICATION NOTE: Regardless of the state of the Noise Status bits, if low frequency noise is detected on a sensor input, that sample will be discarded unless the DIS_ANA_NOISE bit is set. As well, if RF noise is detected on a sensor input, that sample will be discarded unless the DIS_RF_NOISE bit is set. Revision 1.32 (01-05-12) 28 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet 5.4 Sensor Input Delta Count Registers Table 5.6 Sensor Input Delta Count Registers ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 10h R Sensor Input 1 Delta Count Sign 64 32 16 8 4 2 1 00h 11h R Sensor Input 2 Delta Count Sign 64 32 16 8 4 2 1 00h 12h R Sensor Input 3 Delta Count Sign 64 32 16 8 4 2 1 00h The Sensor Input Delta Count registers store the delta count that is compared against the threshold used to determine if a touch has been detected. The count value represents a change in input due to the capacitance associated with a touch on one of the sensor inputs and is referenced to a calibrated base "Not Touched" count value. The delta is an instantaneous change and is updated once per sensor input per sensing cycle (see Section 4.3.1, "Sensing Cycle"). The value presented is a standard 2's complement number. In addition, the value is capped at a value of 7Fh. A reading of 7Fh indicates that the sensitivity settings are too high and should be adjusted accordingly (see Section 5.5). The value is also capped at a negative value of 80h for negative delta counts which may result upon a release. 5.5 Sensitivity Control Register Table 5.7 Sensitivity Control Register ADDR R/W REGISTER B7 1Fh R/W Sensitivity Control - B6 B5 B4 DELTA_SENSE[2:0] B3 B2 B1 B0 DEFAULT BASE_SHIFT[3:0] The Sensitivity Control register controls the sensitivity of a touch detection. Bits 6-4 DELTA_SENSE[2:0] - Controls the sensitivity of a touch detection. The sensitivity settings act to scale the relative delta count value higher or lower based on the system parameters. A setting of 000b is the most sensitive while a setting of 111b is the least sensitive. At the more sensitive settings, touches are detected for a smaller delta capacitance corresponding to a "lighter" touch. These settings are more sensitive to noise, however, and a noisy environment may flag more false touches with higher sensitivity levels. APPLICATION NOTE: A value of 128x is the most sensitive setting available. At the most sensitivity settings, the MSB of the Delta Count register represents 64 out of ~25,000 which corresponds to a touch of approximately 0.25% of the base capacitance (or a C of 25fF from a 10pF base capacitance). Conversely, a value of 1x is the least sensitive setting available. At these settings, the MSB of the Delta Count register corresponds to a delta count of 8192 counts out of ~25,000 which corresponds to a touch of approximately 33% of the base capacitance (or a C of 3.33pF from a 10pF base capacitance). SMSC CAP1133 29 DATASHEET Revision 1.32 (01-05-12) 2Fh 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table 5.8 DELTA_SENSE Bit Decode DELTA_SENSE[2:0] 2 1 0 SENSITIVITY MULTIPLIER 0 0 0 128x (most sensitive) 0 0 1 64x 0 1 0 32x (default) 0 1 1 16x 1 0 0 8x 1 0 1 4x 1 1 0 2x 1 1 1 1x - (least sensitive) Bits 3 - 0 - BASE_SHIFT[3:0] - Controls the scaling and data presentation of the Base Count registers. The higher the value of these bits, the larger the range and the lower the resolution of the data presented. The scale factor represents the multiplier to the bit-weighting presented in these register descriptions. APPLICATION NOTE: The BASE_SHIFT[3:0] bits normally do not need to be updated. These settings will not affect touch detection or sensitivity. These bits are sometimes helpful in analyzing the Cap Sensing board performance and stability. Table 5.9 BASE_SHIFT Bit Decode BASE_SHIFT[3:0] 3 2 1 0 DATA SCALING FACTOR 0 0 0 0 1x 0 0 0 1 2x 0 0 1 0 4x 0 0 1 1 8x 0 1 0 0 16x 0 1 0 1 32x 0 1 1 0 64x 0 1 1 1 128x 1 0 0 0 256x 256x (default = 1111b) All others Revision 1.32 (01-05-12) 30 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet 5.6 Configuration Registers Table 5.10 Configuration Registers ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 20h R/W Configuration TIMEOUT - DIS_ DIG_ NOISE DIS_ ANA_ NOISE MAX_ DUR_EN - - - A0h (rev B) 20h (rev C) 44h R/W Configuration 2 INV_LINK_ TRAN ALT_ POL BLK_PWR_ CTRL BLK_POL_ MIR SHOW_ RF_ NOISE DIS_ RF_ NOISE - INT_ REL_n 40h The Configuration registers control general global functionality that affects the entire device. 5.6.1 Configuration - 20h Bit 7 - TIMEOUT - Enables the timeout and idle functionality of the SMBus protocol. `0' (default for Functional Revision C) - The SMBus timeout and idle functionality are disabled. The SMBus interface will not time out if the clock line is held low. Likewise, it will not reset if both the data and clock lines are held high for longer than 200us. This is used for I2C compliance. `1' (default for Functional Revision B) - The SMBus timeout and idle functionality are enabled. The SMBus interface will time out if the clock line is held low for longer than 30ms. Likewise, it will reset if both the data and clock lines are held high for longer than 200us. Bit 5 - DIS_DIG_NOISE - Determines whether the digital noise threshold (see Section 5.19, "Sensor Input Noise Threshold Register") is used by the device. Setting this bit disables the feature. `0' - The digital noise threshold is used. If a delta count value exceeds the noise threshold but does not exceed the touch threshold, the sample is discarded and not used for the automatic recalibration routine. `1' (default) - The noise threshold is disabled. Any delta count that is less than the touch threshold is used for the automatic re-calibration routine. Bit 4 - DIS_ANA_NOISE - Determines whether the analog noise filter is enabled. Setting this bit disables the feature. `0' (default) - If low frequency noise is detected by the analog block, the delta count on the corresponding channel is set to 0. Note that this does not require that Noise Status bits be set. `1' - A touch is not blocked even if low frequency noise is detected. Bit 3 - MAX_DUR_EN - Determines whether the maximum duration recalibration is enabled. 5.6.2 `0' (default) - The maximum duration recalibration functionality is disabled. A touch may be held indefinitely and no re-calibration will be performed on any sensor input. `1' - The maximum duration recalibration functionality is enabled. If a touch is held for longer than the MAX_DUR bit settings, then the re-calibration routine will be restarted (see Section 5.8). Configuration 2 - 44h Bit 7 - INV_LINK_TRAN - Determines the behavior of the Linked LED Transition controls (see Section 5.29). `0' (default) - The Linked LED Transition controls set the min duty cycle equal to the max duty cycle. `1' - The Linked LED Transition controls will invert the touch signal. For example, a touch signal will be inverted to a non-touched signal. SMSC CAP1133 31 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Bit 6 - ALT_POL - Determines the ALERT# pin polarity and behavior. `0' - The ALERT# pin is active high and push-pull. `1' (default) - The ALERT# pin is active low and open drain. Bit 5 - BLK_PWR_CTRL - Determines whether the device will reduce power consumption while waiting between conversion time completion and the end of the polling cycle. `0' (default) - The device will always power down as much as possible during the time between the end of the last conversion and the end of the polling cycle. `1' - The device will not power down the Cap Sensor during the time between the end of the last conversion and the end of the polling cycle. Bit 4 - BLK_POL_MIR - Determines whether the LED Mirror Control register bits are linked to the LED Polarity bits. Setting this bit blocks the normal behavior which is to automatically set and clear the LED Mirror Control bits when the LED Polarity bits are set or cleared. `0' (default) - When the LED Polarity controls are set, the corresponding LED Mirror control is automatically set. Likewise, when the LED Polarity controls are cleared, the corresponding LED Mirror control is also cleared. `1' - When the LED Polarity controls are set, the corresponding LED Mirror control is not automatically set. Bit 3 - SHOW_RF_NOISE - Determines whether the Noise Status bits will show RF Noise as the only input source. `0' (default) - The Noise Status registers will show both RF noise and low frequency EMI noise if either is detected on a capacitive touch sensor input. `1' - The Noise Status registers will only show RF noise if it is detected on a capacitive touch sensor input. EMI noise will still be detected and touches will be blocked normally; however, the status bits will not be updated. Bit 2 - DIS_RF_NOISE - Determines whether the RF noise filter is enabled. Setting this bit disables the feature. `0' (default) - If RF noise is detected by the analog block, the delta count on the corresponding channel is set to 0. Note that this does not require that Noise Status bits be set. `1' - A touch is not blocked even if RF noise is detected. Bit 0 - INT_REL_n - Controls the interrupt behavior when a release is detected on a button. 5.7 `0' (default) - An interrupt is generated when a press is detected and again when a release is detected and at the repeat rate (if enabled - see Section 5.13). `1' - An interrupt is generated when a press is detected and at the repeat rate but not when a release is detected. Sensor Input Enable Registers Table 5.11 Sensor Input Enable Registers ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 21h R/W Sensor Input Enable - - - - - CS3_EN CS2_EN CS1_EN 07h The Sensor Input Enable registers determine whether a capacitive touch sensor input is included in the sampling cycle. The length of the sampling cycle is not affected by the number of sensor inputs measured. Revision 1.32 (01-05-12) 32 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Bit 2 - CS3_EN - Enables the CS3 input to be included during the sampling cycle. `0' - The CS3 input is not included in the sampling cycle. `1' (default) - The CS3 input is included in the sampling cycle. Bit 1 - CS2_EN - Enables the CS2 input to be included during the sampling cycle. Bit 0 - CS1_EN - Enables the CS1 input to be included during the sampling cycle. 5.8 Sensor Input Configuration Register Table 5.12 Sensor Input Configuration Register ADDR R/W REGISTER 22h R/W Sensor Input Configuration B7 B6 B5 B4 B3 MAX_DUR[3:0] B2 B1 B0 DEFAULT RPT_RATE[3:0] A4h The Sensor Input Configuration Register controls timings associated with the Capacitive sensor inputs 1 - 3. Bits 7 - 4 - MAX_DUR[3:0] - (default 1010b) - Determines the maximum time that a sensor pad is allowed to be touched until the capacitive touch sensor input is recalibrated, as shown in Table 5.13. Table 5.13 MAX_DUR Bit Decode MAX_DUR[3:0] 3 2 1 0 TIME BEFORE RECALIBRATION 0 0 0 0 560ms 0 0 0 1 840ms 0 0 1 0 1120ms 0 0 1 1 1400ms 0 1 0 0 1680ms 0 1 0 1 2240ms 0 1 1 0 2800ms 1 1 1 3360ms SMSC CAP1133 33 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table 5.13 MAX_DUR Bit Decode (continued) MAX_DUR[3:0] 3 2 1 0 TIME BEFORE RECALIBRATION 1 0 0 0 3920ms 1 0 0 1 4480ms 1 0 1 0 5600ms (default) 1 0 1 1 6720ms 1 1 0 0 7840ms 1 1 0 1 8906ms 1 1 1 0 10080ms 1 1 1 1 11200ms Bits 3 - 0 - RPT_RATE[3:0] - (default 0100b) Determines the time duration between interrupt assertions when auto repeat is enabled. The resolution is 35ms the range is from 35ms to 560ms as shown in Table 5.14. Table 5.14 RPT_RATE Bit Decode RPT_RATE[3:0] 3 2 1 0 INTERRUPT REPEAT RATE 0 0 0 0 35ms 0 0 0 1 70ms 0 0 1 0 105ms 0 0 1 1 140ms 0 1 0 0 175ms (default) 0 1 0 1 210ms 0 1 1 0 245ms 0 1 1 1 280ms 1 0 0 0 315ms 1 0 0 1 350ms 1 0 1 0 385ms 1 0 1 1 420ms 1 1 0 0 455ms 1 1 0 1 490ms 1 1 1 0 525ms 1 1 1 1 560ms Revision 1.32 (01-05-12) 34 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet 5.9 Sensor Input Configuration 2 Register Table 5.15 Sensor Input Configuration 2 Register ADDR R/W REGISTER B7 B6 B5 B4 23h R/W Sensor Input Configuration 2 - - - - B3 B2 B1 B0 M_PRESS[3:0] DEFAULT 07h Bits 3 - 0 - M_PRESS[3:0] - (default 0111b) - Determines the minimum amount of time that sensor inputs configured to use auto repeat must detect a sensor pad touch to detect a "press and hold" event. If the sensor input detects a touch for longer than the M_PRESS[3:0] settings, a "press and hold" event is detected. If a sensor input detects a touch for less than or equal to the M_PRESS[3:0] settings, a touch event is detected. The resolution is 35ms the range is from 35ms to 560ms as shown in Table 5.16. Table 5.16 M_PRESS Bit Decode M_PRESS[3:0] 3 2 1 0 M_PRESS SETTINGS 0 0 0 0 35ms 0 0 0 1 70ms 0 0 1 0 105ms 0 0 1 1 140ms 0 1 0 0 175ms 0 1 0 1 210ms 0 1 1 0 245ms 0 1 1 1 280ms (default) 1 0 0 0 315ms 1 0 0 1 350ms 1 0 1 0 385ms 1 0 1 1 420ms 1 1 0 0 455ms 1 1 0 1 490ms 1 1 1 0 525ms 1 1 1 1 560ms SMSC CAP1133 35 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet 5.10 Averaging and Sampling Configuration Register Table 5.17 Averaging and Sampling Configuration Register ADDR R/W REGISTER 24h R/W Averaging and Sampling Config B7 B6 B5 B4 AVG[2:0] B3 B2 SAMP_TIME[1:0] B1 B0 DEFAULT CYCLE_TIME [1:0] 39h The Averaging and Sampling Configuration register controls the number of samples taken and the total sensor input cycle time for all active sensor inputs while the device is functioning in Active state. Bits 6 - 4 - AVG[2:0] - Determines the number of samples that are taken for all active channels during the sensor cycle as shown in Table 5.18. All samples are taken consecutively on the same channel before the next channel is sampled and the result is averaged over the number of samples measured before updating the measured results. For example, if CS1, CS2, and CS3 are sampled during the sensor cycle, and the AVG[2:0] bits are set to take 4 samples per channel, then the full sensor cycle will be: CS1, CS1, CS1, CS1, CS2, CS2, CS2, CS2, CS3, CS3, CS3, CS3. Table 5.18 AVG Bit Decode AVG[2:0] 2 1 0 NUMBER OF SAMPLES TAKEN PER MEASUREMENT 0 0 0 1 0 0 1 2 0 1 0 4 0 1 1 8 (default) 1 0 0 16 1 0 1 32 1 1 0 64 1 1 1 128 Bits 3 - 2 - SAMP_TIME[1:0] - Determines the time to take a single sample as shown in Table 5.19. Table 5.19 SAMP_TIME Bit Decode SAMP_TIME[1:0] 1 0 SAMPLE TIME 0 0 320us 0 1 640us 1 0 1.28ms (default) Revision 1.32 (01-05-12) 36 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table 5.19 SAMP_TIME Bit Decode (continued) SAMP_TIME[1:0] 1 0 SAMPLE TIME 1 1 2.56ms Bits 1 - 0 - CYCLE_TIME[1:0] - Determines the overall cycle time for all measured channels during normal operation as shown in Table 5.20. All measured channels are sampled at the beginning of the cycle time. If additional time is remaining, then the device is placed into a lower power state for the remaining duration of the cycle. Table 5.20 CYCLE_TIME Bit Decode CYCLE_TIME[1:0] 1 0 OVERALL CYCLE TIME 0 0 35ms 0 1 70ms (default) 1 0 105ms 1 1 140ms APPLICATION NOTE: The programmed cycle time is only maintained if the total averaging time for all samples is less than the programmed cycle. The AVG[2:0] bits will take priority so that if more samples are required than would normally be allowed during the cycle time, the cycle time will be extended as necessary to accommodate the number of samples to be measured. 5.11 Calibration Activate Register Table 5.21 Calibration Activate Register ADDR R/W REGISTER 26h R/W Calibration Activate B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT - - - CS3_ CAL CS2_ CAL CS1_ CAL 00h The Calibration Activate register forces the respective sensor inputs to be re-calibrated affecting both the analog and digital blocks. During the re-calibration routine, the sensor inputs will not detect a press for up to 600ms and the Sensor Input Base Count register values will be invalid. During this time, any press on the corresponding sensor pads will invalidate the re-calibration. When finished, the CALX[9:0] bits will be updated (see Section 5.39). When the corresponding bit is set, the device will perform the calibration and the bit will be automatically cleared once the re-calibration routine has finished. Bit 2 - CS3_CAL - When set, the CS3 input is re-calibrated. This bit is automatically cleared once the sensor input has been re-calibrated successfully. Bit 1 - CS2_CAL - When set, the CS2 input is re-calibrated. This bit is automatically cleared once the sensor input has been re-calibrated successfully. SMSC CAP1133 37 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Bit 0 - CS1_CAL - When set, the CS1 input is re-calibrated. This bit is automatically cleared once the sensor input has been re-calibrated successfully. 5.12 Interrupt Enable Register Table 5.22 Interrupt Enable Register ADDR R/W REGISTER 27h R/W Interrupt Enable B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT - - - CS3_ INT_EN CS2_ INT_EN CS1_ INT_EN 07h The Interrupt Enable register determines whether a sensor pad touch or release (if enabled) causes the interrupt pin to be asserted. Bit 2 - CS3_INT_EN - Enables the interrupt pin to be asserted if a touch is detected on CS3 (associated with the CS3 status bit). `0' - The interrupt pin will not be asserted if a touch is detected on CS3 (associated with the CS6 status bit). `1' (default) - The interrupt pin will be asserted if a touch is detected on CS3 (associated with the CS6 status bit). Bit 1 - CS2_INT_EN - Enables the interrupt pin to be asserted if a touch is detected on CS2 (associated with the CS2 status bit). Bit 0 - CS1_INT_EN - Enables the interrupt pin to be asserted if a touch is detected on CS1 (associated with the CS1 status bit). 5.13 Repeat Rate Enable Register Table 5.23 Repeat Rate Enable Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 28h R/W Repeat Rate Enable - - - - - CS3_ RPT_EN CS2_ RPT_EN CS1_ RPT_EN 07h The Repeat Rate Enable register enables the repeat rate of the sensor inputs as described in Section 4.4.1. Bit 2 - CS3_RPT_EN - Enables the repeat rate for capacitive touch sensor input 3. `0' - The repeat rate for CS3 is disabled. It will only generate an interrupt when a touch is detected and when a release is detected no matter how long the touch is held for. `1' (default) - The repeat rate for CS3 is enabled. In the case of a "touch" event, it will generate an interrupt when a touch is detected and a release is detected (as determined by the INT_REL_n bit - see Section 5.6). In the case of a "press and hold" event, it will generate an interrupt when a touch is detected and at the repeat rate so long as the touch is held d. Bit 1 - CS2_RPT_EN - Enables the repeat rate for capacitive touch sensor input 2. Bit 0 - CS1_RPT_EN - Enables the repeat rate for capacitive touch sensor input 1. Revision 1.32 (01-05-12) 38 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet 5.14 Multiple Touch Configuration Register Table 5.24 Multiple Touch Configuration ADDR R/W REGISTER B7 B6 B5 B4 2Ah R/W Multiple Touch Config MULT_ BLK_ EN - - - B3 B2 B_MULT_T[1:0] B1 B0 DEFAULT - - 80h The Multiple Touch Configuration register controls the settings for the multiple touch detection circuitry. These settings determine the number of simultaneous buttons that may be pressed before additional buttons are blocked and the MULT status bit is set. Bit 7 - MULT_BLK_EN - Enables the multiple button blocking circuitry. `0' - The multiple touch circuitry is disabled. The device will not block multiple touches. `1' (default) - The multiple touch circuitry is enabled. The device will flag the number of touches equal to programmed multiple touch threshold and block all others. It will remember which sensor inputs are valid and block all others until that sensor pad has been released. Once a sensor pad has been released, the N detected touches (determined via the cycle order of CS1 - CS3) will be flagged and all others blocked. Bits 3 - 2 - B_MULT_T[1:0] - Determines the number of simultaneous touches on all sensor pads before a Multiple Touch Event is detected and sensor inputs are blocked. The bit decode is given by Table 5.25. Table 5.25 B_MULT_T Bit Decode B_MULT_T[1:0] 5.15 1 0 NUMBER OF SIMULTANEOUS TOUCHES 0 0 1 (default) 0 1 2 1 0 3 1 1 3 Multiple Touch Pattern Configuration Register Table 5.26 Multiple Touch Pattern Configuration ADDR R/W REGISTER B7 B6 B5 2Bh R/W Multiple Touch Pattern Config MTP_ EN - - B4 B3 B2 MTP_TH[1:0] B1 B0 DEFAULT COMP_ PTRN MTP_ ALERT 00h The Multiple Touch Pattern Configuration register controls the settings for the multiple touch pattern detection circuitry. This circuitry works like the multiple touch detection circuitry with the following differences: SMSC CAP1133 39 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet 1. The detection threshold is a percentage of the touch detection threshold as defined by the MTP_TH[1:0] bits whereas the multiple touch circuitry uses the touch detection threshold. 2. The MTP detection circuitry either will detect a specific pattern of sensor inputs as determined by the Multiple Touch Pattern register settings or it will use the Multiple Touch Pattern register settings to determine a minimum number of sensor inputs that will cause the MTP circuitry to flag an event. When using pattern recognition mode, if all of the sensor inputs set by the Multiple Touch Pattern register have a delta count greater than the MTP threshold or have their corresponding Noise Flag Status bits set, the MTP bit will be set. When using the absolute number mode, if the number of sensor inputs with thresholds above the MTP threshold or with Noise Flag Status bits set is equal to or greater than this number, the MTP bit will be set. 3. When an MTP event occurs, all touches are blocked and an interrupt is generated. 4. All sensor inputs will remain blocked so long as the requisite number of sensor inputs are above the MTP threshold or have Noise Flag Status bits set. Once this condition is removed, touch detection will be restored. Note that the MTP status bit is only cleared by writing a `0' to the INT bit once the condition has been removed. Bit 7 - MTP_EN - Enables the multiple touch pattern detection circuitry. `0' (default) - The MTP detection circuitry is disabled. `1' - The MTP detection circuitry is enabled. Bits 3-2 - MTP_TH[1:0] - Determine the MTP threshold, as shown in Table 5.27. This threshold is a percentage of sensor input threshold (see Section 5.18, "Sensor Input Threshold Registers") when the device is in the Fully Active state or of the standby threshold (see Section 5.23, "Standby Threshold Register") when the device is in the Standby state. Table 5.27 MTP_TH Bit Decode MTP_TH[1:0] 1 0 THRESHOLD DIVIDE SETTING 0 0 12.5% (default) 0 1 25% 1 0 37.5% 1 1 100% Bit 1 - COMP_PTRN - Determines whether the MTP detection circuitry will use the Multiple Touch Pattern register as a specific pattern of sensor inputs or as an absolute number of sensor inputs. `0' (default) - The MTP detection circuitry will use the Multiple Touch Pattern register bit settings as an absolute minimum number of sensor inputs that must be above the threshold or have Noise Flag Status bits set. The number will be equal to the number of bits set in the register. `1' - The MTP detection circuitry will use pattern recognition. Each bit set in the Multiple Touch Pattern register indicates a specific sensor input that must have a delta count greater than the MTP threshold or have a Noise Flag Status bit set. If the criteria are met, the MTP status bit will be set. Bit 0 - MTP_ALERT - Enables an interrupt if an MTP event occurs. In either condition, the MTP status bit will be set. `0' (default) - If an MTP event occurs, the ALERT# pin is not asserted. `1' - If an MTP event occurs, the ALERT# pin will be asserted. Revision 1.32 (01-05-12) 40 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet 5.16 Multiple Touch Pattern Register Table 5.28 Multiple Touch Pattern Register ADDR R/W REGISTER 2Dh R/W Multiple Touch Pattern B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT - - - CS3_ PTRN CS2_ PTRN CS1_ PTRN 07h The Multiple Touch Pattern register acts as a pattern to identify an expected sensor input profile for diagnostics or other significant events. There are two methods for how the Multiple Touch Pattern register is used: as specific sensor inputs or number of sensor input that must exceed the MTP threshold or have Noise Flag Status bits set. Which method is used is based on the COMP_PTRN bit (see Section 5.15). The methods are described below. 1. Specific Sensor Inputs: If, during a single polling cycle, the specific sensor inputs above the MTP threshold or with Noise Flag Status bits set match those bits set in the Multiple Touch Pattern register, an MTP event is flagged. 2. Number of Sensor Inputs: If, during a single polling cycle, the number of sensor inputs with a delta count above the MTP threshold or with Noise Flag Status bits set is equal to or greater than the number of pattern bits set, an MTP event is flagged. Bit 2 - CS3_PTRN - Determines whether CS3 is considered as part of the Multiple Touch Pattern. `0' - CS3 is not considered a part of the pattern. `1' - CS3 is considered a part of the pattern or the absolute number of sensor inputs that must have a delta count greater than the MTP threshold or have the Noise Flag Status bit set is increased by 1. Bit 1 - CS2_PTRN - Determines whether CS2 is considered as part of the Multiple Touch Pattern. Bit 0 - CS1_PTRN - Determines whether CS1 is considered as part of the Multiple Touch Pattern. 5.17 Recalibration Configuration Register Table 5.29 Recalibration Configuration Registers ADDR R/W REGISTER B7 B6 B5 2Fh R/W Recalibration Configuration BUT_ LD_TH NO_ CLR_ INTD NO_ CLR_ NEG B4 B3 B2 NEG_DELTA_ CNT[1:0] B1 CAL_CFG[2:0] B0 DEFAULT 8Ah The Recalibration Configuration register controls the automatic re-calibration routine settings as well as advanced controls to program the Sensor Input Threshold register settings. Bit 7 - BUT_LD_TH - Enables setting all Sensor Input Threshold registers by writing to the Sensor Input 1 Threshold register. `0' - Each Sensor Input X Threshold register is updated individually. `1' (default) - Writing the Sensor Input 1 Threshold register will automatically overwrite the Sensor Input Threshold registers for all sensor inputs (Sensor Input Threshold 1 through Sensor Input Threshold 3). The individual Sensor Input X Threshold registers (Sensor Input 2 Threshold and Sensor Input 3 Threshold) can be individually updated at any time. SMSC CAP1133 41 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Bit 6 - NO_CLR_INTD - Controls whether the accumulation of intermediate data is cleared if the noise status bit is set. `0' (default) - The accumulation of intermediate data is cleared if the noise status bit is set. `1' - The accumulation of intermediate data is not cleared if the noise status bit is set. APPLICATION NOTE: Bits 5 and 6 should both be set to the same value. Either both should be set to `0' or both should be set to `1'. Bit 5 - NO_CLR_NEG - Controls whether the consecutive negative delta counts counter is cleared if the noise status bit is set. `0' (default) - The consecutive negative delta counts counter is cleared if the noise status bit is set. `1' - The consecutive negative delta counts counter is not cleared if the noise status bit is set. Bits 4 - 3 - NEG_DELTA_CNT[1:0] - Determines the number of negative delta counts necessary to trigger a digital re-calibration as shown in Table 5.30. Table 5.30 NEG_DELTA_CNT Bit Decode NEG_DELTA_CNT[1:0] 1 0 NUMBER OF CONSECUTIVE NEGATIVE DELTA COUNT VALUES 0 0 8 0 1 16 (default) 1 0 32 1 1 None (disabled) Bits 2 - 0 - CAL_CFG[2:0] - Determines the update time and number of samples of the automatic recalibration routine. The settings apply to all sensor inputs universally (though individual sensor inputs can be configured to support re-calibration - see Section 5.11). Table 5.31 CAL_CFG Bit Decode CAL_CFG[2:0] 2 1 0 RECALIBRATION SAMPLES (SEE Note 5.1) 0 0 0 16 16 0 0 1 32 32 0 1 0 64 64 (default) 0 1 1 128 128 1 0 0 256 256 1 0 1 256 1024 1 1 0 256 2048 1 1 1 256 4096 Revision 1.32 (01-05-12) 42 DATASHEET UPDATE TIME (SEE Note 5.2) SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet 5.18 Note 5.1 Recalibration Samples refers to the number of samples that are measured and averaged before the Base Count is updated however does not control the base count update period. Note 5.2 Update Time refers to the amount of time (in polling cycle periods) that elapses before the Base Count is updated. The time will depend upon the number of channels active, the averaging setting, and the programmed cycle time. Sensor Input Threshold Registers Table 5.32 Sensor Input Threshold Registers ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 30h R/W Sensor Input 1 Threshold - 64 32 16 8 4 2 1 40h 31h R/W Sensor Input 2 Threshold - 64 32 16 8 4 2 1 40h 32h R/W Sensor Input 3 Threshold - 64 32 16 8 4 2 1 40h The Sensor Input Threshold registers store the delta threshold that is used to determine if a touch has been detected. When a touch occurs, the input signal of the corresponding sensor pad changes due to the capacitance associated with a touch. If the sensor input change exceeds the threshold settings, a touch is detected. When the BUT_LD_TH bit is set (see Section 5.17 - bit 7), writing data to the Sensor Input 1 Threshold register will update all of the sensor input threshold registers (31h - 32h inclusive). 5.19 Sensor Input Noise Threshold Register Table 5.33 Sensor Input Noise Threshold Register ADDR R/W REGISTER 38h R/W Sensor Input Noise Threshold B7 B6 B5 B4 B3 B2 B1 B0 CS_BN_TH [1:0] DEFAULT 01h The Sensor Input Noise Threshold register controls the value of a secondary internal threshold to detect noise and improve the automatic recalibration routine. If a capacitive touch sensor input exceeds the Sensor Input Noise Threshold but does not exceed the sensor input threshold, it is determined to be caused by a noise spike. That sample is not used by the automatic re-calibration routine. This feature can be disabled by setting the DIS_DIG_NOISE bit. Bits 1-0 - CS1_BN_TH[1:0] - Controls the noise threshold for all capacitive touch sensor inputs, as shown in Table 5.34. The threshold is proportional to the threshold setting. SMSC CAP1133 43 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table 5.34 CSx_BN_TH Bit Decode CS_BN_TH[1:0] 5.20 1 0 PERCENT THRESHOLD SETTING 0 0 25% 0 1 37.5% (default) 1 0 50% 1 1 62.5% Standby Channel Register Table 5.35 Standby Channel Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 40h R/W Standby Channel - - - - - CS3_ STBY CS2_ STBY CS1_ STBY 00h The Standby Channel register controls which (if any) capacitive touch sensor inputs are active during Standby. Bit 2 - CS3_STBY - Controls whether the CS3 channel is active in Standby. `0' (default) - The CS3 channel not be sampled during Standby mode. `1' - The CS3 channel will be sampled during Standby Mode. It will use the Standby threshold setting, and the standby averaging and sensitivity settings. Bit 1 - CS2_STBY - Controls whether the CS2 channel is active in Standby. Bit 0 - CS1_STBY - Controls whether the CS1 channel is active in Standby. 5.21 Standby Configuration Register Table 5.36 Standby Configuration Register ADDR R/W REGISTER B7 41h R/W Standby Configuration AVG_ SUM B6 B5 B4 STBY_AVG[2:0] B3 B2 STBY_SAMP_ TIME[1:0] B1 B0 STBY_CY_TIME [1:0] DEFAULT 39h The Standby Configuration register controls averaging and cycle time for those sensor inputs that are active in Standby. This register is useful for detecting proximity on a small number of sensor inputs as it allows the user to change averaging and sample times on a limited number of sensor inputs and still maintain normal functionality in the fully active state. Bit 7 - AVG_SUM - Determines whether the active sensor inputs will average the programmed number of samples or whether they will accumulate for the programmed number of samples. Revision 1.32 (01-05-12) 44 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet `0' - (default) - The active sensor input delta count values will be based on the average of the programmed number of samples when compared against the threshold. `1' - The active sensor input delta count values will be based on the summation of the programmed number of samples when compared against the threshold. This bit should only be set when performing proximity detection as a physical touch will overflow the delta count registers and may result in false readings. Bits 6 - 4 - STBY_AVG[2:0] - Determines the number of samples that are taken for all active channels during the sensor cycle as shown in Table 5.37. All samples are taken consecutively on the same channel before the next channel is sampled and the result is averaged over the number of samples measured before updating the measured results. Table 5.37 STBY_AVG Bit Decode STBY_AVG[2:0] 2 1 0 NUMBER OF SAMPLES TAKEN PER MEASUREMENT 0 0 0 1 0 0 1 2 0 1 0 4 0 1 1 8 (default) 1 0 0 16 1 0 1 32 1 1 0 64 1 1 1 128 Bit 3-2 - STBY SAMP_TIME[1:0] - Determines the time to take a single sample when the device is in Standby as shown in Table 5.38. Table 5.38 STBY_SAMP_TIME Bit Decode STBY_SAMP_TIME[1:0] 1 0 SAMPLING TIME 0 0 320us 0 1 640us 1 0 1.28ms (default) 1 1 2.56ms Bits 1 - 0 - STBY_CY_TIME[2:0] - Determines the overall cycle time for all measured channels during standby operation as shown in Table 5.39. All measured channels are sampled at the beginning of the cycle time. If additional time is remaining, the device is placed into a lower power state for the remaining duration of the cycle. SMSC CAP1133 45 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table 5.39 STBY_CY_TIME Bit Decode STBY_CY_TIME[1:0] 1 0 OVERALL CYCLE TIME 0 0 35ms 0 1 70ms (default) 1 0 105ms 1 1 140ms APPLICATION NOTE: The programmed cycle time is only maintained if the total averaging time for all samples is less than the programmed cycle. The STBY_AVG[2:0] bits will take priority so that if more samples are required than would normally be allowed during the cycle time, the cycle time will be extended as necessary to accommodate the number of samples to be measured. 5.22 Standby Sensitivity Register Table 5.40 Standby Sensitivity Register ADDR R/W REGISTER B7 B6 B5 B4 B3 42h R/W Standby Sensitivity - - - - - B2 B1 B0 DEFAULT STBY_SENSE[2:0] 02h The Standby Sensitivity register controls the sensitivity for sensor inputs that are active in Standby. Bits 2 - 0 - STBY_SENSE[2:0] - Controls the sensitivity for sensor inputs that are active in Standby. The sensitivity settings act to scale the relative delta count value higher or lower based on the system parameters. A setting of 000b is the most sensitive while a setting of 111b is the least sensitive. At the more sensitive settings, touches are detected for a smaller delta C corresponding to a "lighter" touch. These settings are more sensitive to noise however and a noisy environment may flag more false touches than higher sensitivity levels. APPLICATION NOTE: A value of 128x is the most sensitive setting available. At the most sensitivity settings, the MSB of the Delta Count register represents 64 out of ~25,000 which corresponds to a touch of approximately 0.25% of the base capacitance (or a C of 25fF from a 10pF base capacitance). Conversely a value of 1x is the least sensitive setting available. At these settings, the MSB of the Delta Count register corresponds to a delta count of 8192 counts out of ~25,000 which corresponds to a touch of approximately 33% of the base capacitance (or a C of 3.33pF from a 10pF base capacitance). Table 5.41 STBY_SENSE Bit Decode STBY_SENSE[2:0] 2 1 0 SENSITIVITY MULTIPLIER 0 0 0 128x (most sensitive) 0 0 1 64x Revision 1.32 (01-05-12) 46 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table 5.41 STBY_SENSE Bit Decode (continued) STBY_SENSE[2:0] 5.23 2 1 0 SENSITIVITY MULTIPLIER 0 1 0 32x (default) 0 1 1 16x 1 0 0 8x 1 0 1 4x 1 1 0 2x 1 1 1 1x - (least sensitive) Standby Threshold Register Table 5.42 Standby Threshold Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 43h R/W Standby Threshold - 64 32 16 8 4 2 1 40h The Standby Threshold register stores the delta threshold that is used to determine if a touch has been detected. When a touch occurs, the input signal of the corresponding sensor pad changes due to the capacitance associated with a touch. If the sensor input change exceeds the threshold settings, a touch is detected. 5.24 Sensor Input Base Count Registers Table 5.43 Sensor Input Base Count Registers ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 50h R Sensor Input 1 Base Count 128 64 32 16 8 4 2 1 C8h 51h R Sensor Input 2 Base Count 128 64 32 16 8 4 2 1 C8h 52h R Sensor Input 3 Base Count 128 64 32 16 8 4 2 1 C8h The Sensor Input Base Count registers store the calibrated "Not Touched" input value from the capacitive touch sensor inputs. These registers are periodically updated by the re-calibration routine. The routine uses an internal adder to add the current count value for each reading to the sum of the previous readings until sample size has been reached. At this point, the upper 16 bits are taken and used as the Sensor Input Base Count. The internal adder is then reset and the re-calibration routine continues. The data presented is determined by the BASE_SHIFT[3:0] bits (see Section 5.5). SMSC CAP1133 47 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet 5.25 LED Output Type Register Table 5.44 LED Output Type Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 71h R/W LED Output Type - - - - - LED3_ OT LED2_ OT LED1_ OT 00h The LED Output Type register controls the type of output for the LED pins. Each pin is controlled by a single bit. Refer to application note 21.4 CAP1188 Family LED Configuration Options for more information about implementing LEDs. Bit 2 - LED3_OT - Determines the output type of the LED3 pin. `0' (default) - The LED3 pin is an open-drain output with an external pull-up resistor. When the appropriate pin is set to the "active" state (logic `1'), the pin will be driven low. Conversely, when the pin is set to the "inactive" state (logic `0'), the pin will be left in a High Z state and pulled high via an external pull-up resistor. `1' - The LED3 pin is a push-pull output. When driving a logic `1', the pin is driven high. When driving a logic `0', the pin is driven low. Bit 1 - LED2_OT - Determines the output type of the LED2 pin. Bit 0 - LED1_OT - Determines the output type of the LED1 pin. 5.26 Sensor Input LED Linking Register Table 5.45 Sensor Input LED Linking Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 72h R/W Sensor Input LED Linking - - - - - CS3_ LED3 CS2_ LED2 CS1_ LED1 00h The Sensor Input LED Linking register controls whether a capacitive touch sensor input is linked to an LED output. If the corresponding bit is set, then the appropriate LED output will change states defined by the LED Behavior controls (see Section 5.31) in response to the capacitive touch sensor input. Bit 2 - CS3_LED3 - Links the LED3 output to a detected touch on the CS3 sensor input. When a touch is detected, the LED is actuated and will behave as determined by the LED Behavior controls. `0' (default) - The LED 3 output is not associated with the CS3 input. If a touch is detected on the CS3 input, the LED will not automatically be actuated. The LED is enabled and controlled via the LED Output Control register (see Section 5.28) and the LED Behavior registers (see Section 5.31). `1' - The LED 3 output is associated with the CS3 input. If a touch is detected on the CS3 input, the LED will be actuated and behave as defined in Table 5.52. Bit 1 - CS2_LED2 - Links the LED2 output to a detected touch on the CS2 sensor input. When a touch is detected, the LED is actuated and will behave as determined by the LED Behavior controls. Bit 0 - CS1_LED1 - Links the LED1 output to a detected touch on the CS1 sensor input. When a touch is detected, the LED is actuated and will behave as determined by the LED Behavior controls. Revision 1.32 (01-05-12) 48 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet 5.27 LED Polarity Register Table 5.46 LED Polarity Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 73h R/W LED Polarity - - - - - LED3_ POL LED2_ POL LED1_ POL 00h The LED Polarity register controls the logical polarity of the LED outputs. When these bits are set or cleared, the corresponding LED Mirror controls are also set or cleared (unless the BLK_POL_MIR bit is set - see Section 5.6, "Configuration Registers"). Table 5.48, "LED Polarity Behavior" shows the interaction between the polarity controls, output controls, and relative brightness. APPLICATION NOTE: The polarity controls determine the final LED pin drive. A touch on a linked capacitive touch sensor input is treated in the same way as the LED Output Control bit being set to a logic `1'. APPLICATION NOTE: The LED drive assumes that the LEDs are configured such that if the LED pin is driven to a logic `0' then the LED will be on and that the CAP1133 LED pin is sinking the LED current. Conversely, if the LED pin is driven to a logic `1', the LED will be off and there is no current flow. See Figure 4.1, "System Diagram for CAP1133". APPLICATION NOTE: This application note applies when the LED polarity is inverted (LEDx_POL = `0'). For LED operation, the duty cycle settings determine the % of time that the LED pin will be driven to a logic `0' state in. The Max Duty Cycle settings define the maximum % of time that the LED pin will be driven low (i.e. maximum % of time that the LED is on) while the Min Duty Cycle settings determine the minimum % of time that the LED pin will be driven low (i.e. minimum % of time that the LED is on). When there is no touch detected or the LED Output Control register bit is at a logic `0', the LED output will be driven at the minimum duty cycle setting. Breathe operations will ramp the duty cycle from the minimum duty cycle to the maximum duty cycle. APPLICATION NOTE: This application note applies when the LED polarity is non-inverted (LEDx_POL = `1'). For LED operation, the duty cycle settings determine the % of time that the LED pin will be driven to a logic `1' state. The Max Duty Cycle settings define the maximum % of time that the LED pin will be driven high (i.e. maximum % of time that the LED is off) while the Min Duty Cycle settings determine the minimum % of time that the LED pin will be driven high (i.e. minimum % of time that the LED is off). When there is no touch detected or the LED Output Control register bit is at a logic `0', the LED output will be driven at 100 minus the minimum duty cycle setting. Breathe operations will ramp the duty cycle from 100 minus the minimum duty cycle to 100 minus the maximum duty cycle. APPLICATION NOTE: The LED Mirror controls (see Section 5.30, "LED Mirror Control Register") work with the polarity controls with respect to LED brightness but will not have a direct effect on the output pin drive. Bit 2 - LED3_POL - Determines the polarity of the LED3 output. `0' (default) - The LED3 output is inverted. For example, a setting of `1' in the LED Output Control register will cause the LED pin output to be driven to a logic `0'. `1' - The LED3 output is non-inverted. For example, a setting of `1' in the LED Output Control register will cause the LED pin output to be driven to a logic `1' or left in the high-z state as determined by its output type Bit 1 - LED2_POL - Determines the polarity of the LED2 output. Bit 0 - LED1_POL - Determines the polarity of the LED1 output. SMSC CAP1133 49 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet 5.28 LED Output Control Register Table 5.47 LED Output Control Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 74h R/W LED Output Control - - - - - LED3_ DR LED2_ DR LED1_ DR 00h The LED Output Control Register controls the output state of the LED pins that are not linked to sensor inputs. Note: If an LED is linked to a sensor input in the Sensor Input LED Linking Register (Section 5.26, "Sensor Input LED Linking Register"), the corresponding bit in the LED Output Control Register is ignored (i.e. a linked LED cannot be host controlled). The LED Polarity Control Register will determine the non actuated state of the LED pins. The actuated LED behavior is determined by the LED behavior controls (see Section 5.31, "LED Behavior Register"). Table 5.48 shows the interaction between the polarity controls, output controls, and relative brightness. Bit 2 - LED3_DR - Determines whether LED3 output is driven high or low. `0' (default) - The LED3 output is driven at the minimum duty cycle or not actuated. `1' - The LED3 output is driven at the maximum duty cycle or is actuated. Bit 1 - LED2_DR - Determines whether LED2 output is driven high or low. Bit 0 - LED1_DR - Determines whether LED1 output is driven high or low. Table 5.48 LED Polarity Behavior LED OUTPUT CONTROL REGISTER OR TOUCH POLARITY MAX DUTY MIN DUTY BRIGHTNESS LED APPEARANCE inverted (`0') not used minimum % of time that the LED is on (logic 0) maximum brightness at min duty cycle on at min duty cycle 1 inverted (`0') maximum % of time that the LED is on (logic 0) minimum % of time that the LED is on (logic 0) maximum brightness at max duty cycle. Brightness ramps from min duty cycle to max duty cycle according to LED behavior 0 noninverted (`1') not used minimum % of time that the LED is off (logic 1) maximum brightness at 100 minus min duty cycle. on at 100 - min duty cycle 0 Revision 1.32 (01-05-12) 50 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table 5.48 LED Polarity Behavior (continued) LED OUTPUT CONTROL REGISTER OR TOUCH POLARITY noninverted (`1') 1 5.29 MAX DUTY maximum % of time that the LED is off (logic 1) LED APPEARANCE MIN DUTY BRIGHTNESS minimum % of time that the LED is off (logic 1) For Direct behavior, maximum brightness is 100 minus max duty cycle. When breathing, max brightness is 100 minus min duty cycle. Brightness ramps from 100 - min duty cycle to 100 - max duty cycle. according to LED behavior Linked LED Transition Control Register Table 5.49 Linked LED Transition Control Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 77h R/W Linked LED Transition Control - - - - - LED3_ LTRAN LED2_ LTRAN LED1_ LTRAN 00h The Linked LED Transition Control register controls the LED drive when the LED is linked to a capacitive touch sensor input. These controls work in conjunction with the INV_LINK_TRAN bit (see Section 5.6.2, "Configuration 2 - 44h") to create smooth transitions from host control to linked LEDs. Bit 2 - LED3_LTRAN - Determines the transition effect when LED3 is linked to CS3. `0' (default) - When the LED output control bit for CS3 is `1', and then CS3 is linked to LED3 and no touch is detected, the LED will change states. `1' - If the INV_LINK_TRAN bit is `1', when the LED output control bit for CS3 is `1', and then CS3 is linked to LED3 and no touch is detected, the LED will not change states. In addition, the LED state will change when the sensor pad is touched. If the INV_LINK_TRAN bit is `0', when the LED output control bit for CS3 is `1', and then CS3 is linked to LED3 and no touch is detected, the LED will not change states. However, the LED state will not change when the sensor pad is touched. APPLICATION NOTE: If the LED behavior is not "Direct" and the INV_LINK_TRAN bit it `0', the LED will not perform as expected when the LED3_LTRAN bit is set to `1'. Therefore, if breathe and pulse behaviors are used, set the INV_LINK_TRAN bit to `1'. Bit 1 - LED2_LTRAN - Determines the transition effect when LED2 is linked to CS2. Bit 0 - LED1_LTRAN - Determines the transition effect when LED1 is linked to CS1. SMSC CAP1133 51 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet 5.30 LED Mirror Control Register Table 5.50 LED Mirror Control Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 79h R/W LED Mirror Control - - - - - LED3_ MIR_ EN LED2_ MIR _ EN LED1_ MIR _ EN 00h The LED Mirror Control Registers determine the meaning of duty cycle settings when polarity is noninverted for each LED channel. When the polarity bit is set to `1' (non-inverted), to obtain correct steps for LED ramping, pulse, and breathe behaviors, the min and max duty cycles need to be relative to 100%, rather than the default, which is relative to 0%. APPLICATION NOTE: The LED drive assumes that the LEDs are configured such that if the LED pin is driven to a logic `0', the LED will be on and the CAP1133 LED pin is sinking the LED current. When the polarity bit is set to `1', it is considered non-inverted. For systems using the opposite LED configuration, mirror controls would apply when the polarity bit is `0'. These bits are changed automatically if the corresponding LED Polarity bit is changed (unless the BLK_POL_MIR bit is set - see Section 5.6). Bit 2 - LED3_MIR_EN - Determines whether the duty cycle settings are "biased" relative to 0% or 100% duty cycle. `0' (default) - The duty cycle settings are determined relative to 0% and are determined directly with the settings. `1' - The duty cycle settings are determined relative to 100%. Bit 1 - LED2_MIR_EN - Determines whether the duty cycle settings are "biased" relative to 0% or 100% duty cycle. Bit 0 - LED1_MIR_EN - Determines whether the duty cycle settings are "biased" relative to 0% or 100% duty cycle. 5.31 LED Behavior Register Table 5.51 LED Behavior Register ADDR R/W REGISTER B7 B6 81h R/W LED Behavior 1 - - B5 B4 LED3_CTL[1:0] B3 B2 LED2_CTL[1:0] B1 B0 LED1_CTL[1:0] DEFAULT 00h The LED Behavior register controls the operation of LEDs. Each LED pin is controlled by a 2-bit field and the behavior is determined by whether the LED is linked to a capacitive touch sensor input or not. If the corresponding LED output is linked to a capacitive touch sensor input, the appropriate behavior will be enabled / disabled based on touches and releases. If the LED output is not associated with a capacitive touch sensor input, the appropriate behavior will be enabled / disabled by the LED Output Control register. If the respective LEDx_DR bit is set to a logic `1', this will be associated as a "touch", and if the LEDx_DR bit is set to a logic `0', this will be associated as a "release". Revision 1.32 (01-05-12) 52 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table 5.52, "LEDx_CTL Bit Decode" shows the behavior triggers. The defined behavior will activate when the Start Trigger is met and will stop when the Stop Trigger is met. Note the behavior of the Breathe Hold and Pulse Release option. The LED Polarity Control register will determine the non actuated state of the LED outputs (see Section 5.27, "LED Polarity Register"). APPLICATION NOTE: If an LED is not linked to a capacitive touch sensor input and is breathing (via the Breathe or Pulse behaviors), it must be unactuated and then re-actuated before changes to behavior are processed. For example, if the LED output is breathing and the Maximum duty cycle is changed, this change will not take effect until the LED output control register is set to `0' and then re-set to `1'. APPLICATION NOTE: If an LED is not linked to the capacitive touch sensor input and configured to operate using Pulse 1 Behavior, then the circuitry will only be actuated when the corresponding output control bit is set. It will not check the bit condition until the Pulse 1 behavior is finished. The device will not remember if the bit was cleared and reset while it was actuated. APPLICATION NOTE: If an LED is actuated and not linked and the desired LED behavior is changed, this new behavior will take effect immediately; however, the first instance of the changed behavior may act incorrectly (e.g. if changed from Direct to Pulse 1, the LED output may `breathe' 4 times and then end at minimum duty cycle). LED Behaviors will operate normally once the LED has been un-actuated and then re-actuated. APPLICATION NOTE: If an LED is actuated and it is switched from linked to a capacitive touch sensor input to unlinked (or vice versa), the LED will respond to the new command source immediately if the behavior was Direct or Breathe. For Pulse behaviors, it will complete the behavior already in progress. For example, if a linked LED was actuated by a touch and the control is changed so that it is unlinked, it will check the status of the corresponding LED Output Control bit. If that bit is `0', then the LED will behave as if a release was detected. Likewise, if an unlinked LED was actuated by the LED Output Control register and the control is changed so that it is linked and no touch is detected, then the LED will behave as if a release was detected. Bits 5 - 4 - LED3_CTL[1:0] - Determines the behavior of LED3 as shown in Table 5.52. Bits 3 - 2 - LED2_CTL[1:0] - Determines the behavior of LED2 as shown in Table 5.52. Bits 1 - 0 - LED1_CTL[1:0] - Determines the behavior of LED1 as shown in Table 5.52. Table 5.52 LEDx_CTL Bit Decode LEDX_CTL [1:0] 1 0 0 0 0 1 SMSC CAP1133 OPERATION DESCRIPTION START TRIGGER STOP TRIGGER Release Detected or LED Output Control bit cleared n/a Direct The LED is driven to the programmed state (active or inactive). See Figure 5.7 Touch Detected or LED Output Control bit set Pulse 1 The LED will "Pulse" a programmed number of times. During each "Pulse" the LED will breathe up to the maximum brightness and back down to the minimum brightness so that the total "Pulse" period matches the programmed value. Touch or Release Detected or LED Output Control bit set or cleared (see Section 5.32) 53 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table 5.52 LEDx_CTL Bit Decode (continued) LEDX_CTL [1:0] 1 1 1 0 START TRIGGER STOP TRIGGER Pulse 2 The LED will "Pulse" when the start trigger is detected. When the stop trigger is detected, it will "Pulse" a programmable number of times then return to its minimum brightness. Touch Detected or LED Output Control bit set Release Detected or LED Output Control bit cleared Breathe The LED will breathe. It will be driven with a duty cycle that ramps up from the programmed minimum duty cycle (default 0%) to the programmed maximum duty cycle duty cycle (default 100%) and then back down. Each ramp takes up 50% of the programmed period. The total period of each "breath" is determined by the LED Breathe Period controls - see Section 5.34. Touch Detected or LED Output Control bit set Release Detected or LED Output Control bit cleared OPERATION DESCRIPTION 0 1 APPLICATION NOTE: The PWM frequency is determined based on the selected LED behavior, the programmed breathe period, and the programmed min and max duty cycles. For the Direct behavior mode, the PWM frequency is calculated based on the programmed Rise and Fall times. If these are set at 0, then the maximum PWM frequency will be used based on the programmed duty cycle settings. 5.32 LED Pulse 1 Period Register Table 5.53 LED Pulse 1 Period Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 84h R/W LED Pulse 1 Period ST_ TRIG P1_ PER6 P1_ PER5 P1_ PER4 P1_ PER3 P1_ PER2 P1_ PER1 P1_ PER0 20h The LED Pulse Period 1 register determines the overall period of a pulse operation as determined by the LED_CTL registers (see Table 5.52 - setting 01b). The LSB represents 32ms so that a setting of 18h (24d) would represent a period of 768ms (24 x 32ms = 768ms). The total range is from 32ms to 4.064 seconds as shown in Table 5.54 with the default being 1024ms. APPLICATION NOTE: Due to constraints on the LED Drive PWM operation, any Breathe Period less than 160ms (05h) may not be achievable. The device will breathe at the minimum period possible as determined by the period and min / max duty cycle settings. Bit 7 - ST_TRIG - Determines the start trigger for the LED Pulse behavior. `0' (default) - The LED will Pulse when a touch is detected or the drive bit is set. `1' - The LED will Pulse when a release is detected or the drive bit is cleared. The Pulse 1 operation is shown in Figure 5.1 when the LED output is configured for non-inverted polarity (LEDx_POL = 1) and in Figure 5.2 for inverted polarity (LEDx_POL = 0). Revision 1.32 (01-05-12) 54 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet . Touch Detected or Release Detected X pulses after touch or after release Normal - untouched operation (100% - Pulse 1 Min Duty Cycle) * Brightness Normal - untouched operation LED Brightness (100% - Pulse 1 Max Duty Cycle) * Brightness Pulse 1 Period (P1_PER) Figure 5.1 Pulse 1 Behavior with Non-Inverted Polarity Touch Detected or Release Detected X pulses after touch or after release Pulse 1 Max Duty Cycle * Brightness LED Brightness Normal - untouched operation Normal - untouched operation Pulse 1 Min Duty Cycle * Brightness Pulse Period (P1_PER) Figure 5.2 Pulse 1 Behavior with Inverted Polarity Table 5.54 LED Pulse / Breathe Period Example SETTING (HEX) SETTING (DECIMAL) TOTAL BREATHE / PULSE PERIOD (MS) 00h 0 32 01h 1 32 02h 2 64 SMSC CAP1133 55 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table 5.54 LED Pulse / Breathe Period Example (continued) 5.33 SETTING (HEX) SETTING (DECIMAL) TOTAL BREATHE / PULSE PERIOD (MS) 03h 3 96 ... ... ... 7Dh 125 4000 7Eh 126 4032 7Fh 127 4064 LED Pulse 2 Period Register Table 5.55 LED Pulse 2 Period Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 85h R/W LED Pulse 2 Period - P2_ PER6 P2_ PER5 P2_ PER4 P2_ PER3 P2_ PER2 P2_ PER1 P2_ PER0 14h The LED Pulse 2 Period register determines the overall period of a pulse operation as determined by the LED_CTL registers (see Table 5.52 - setting 10b). The LSB represents 32ms so that a setting of 18h (24d) would represent a period of 768ms. The total range is from 32ms to 4.064 seconds (see Table 5.54) with a default of 640ms. APPLICATION NOTE: Due to constraints on the LED Drive PWM operation, any Breathe Period less than 160ms (05h) may not be achievable. The device will breathe at the minimum period possible as determined by the period and min / max duty cycle settings. The Pulse 2 Behavior is shown in Figure 5.3 for non-inverted polarity (LEDx_POL = 1) and in Figure 5.4 for inverted polarity (LEDx_POL = 0). Normal - untouched operation Release Detected Touch Detected X additional pulses after release Normal - untouched operation (100% - Pulse 2 Min Duty Cycle) * Brightness LED Brightness ... Pulse Period (P2_PER) (100% - Pulse 2 Max Duty Cycle) * Brightness Figure 5.3 Pulse 2 Behavior with Non-Inverted Polarity Revision 1.32 (01-05-12) 56 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Normal - untouched operation Release Detected Touch Detected Normal - untouched operation X additional pulses after release Pulse 2 Max Duty Cycle * Brightness LED Brightness ... Pulse 2 Min Duty Cycle * Brightness Pulse Period (P2_PER) Figure 5.4 Pulse 2 Behavior with Inverted Polarity 5.34 LED Breathe Period Register Table 5.56 LED Breathe Period Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 86h R/W LED Breathe Period - BR_ PER6 BR_ PER5 BR_ PER4 BR_ PER3 BR_ PER2 BR_ PER1 BR_ PER0 5Dh The LED Breathe Period register determines the overall period of a breathe operation as determined by the LED_CTL registers (see Table 5.52 - setting 11b). The LSB represents 32ms so that a setting of 18h (24d) would represent a period of 768ms. The total range is from 32ms to 4.064 seconds (see Table 5.54) with a default of 2976ms. APPLICATION NOTE: Due to constraints on the LED Drive PWM operation, any Breathe Period less than 160ms (05h) may not be achievable. The device will breathe at the minimum period possible as determined by the period and min / max duty cycle settings. 5.35 LED Configuration Register Table 5.57 LED Configuration Register ADDR R/W REGISTER B7 B6 88h R/W LED Config - RAMP_ ALERT B5 B4 B3 PULSE2_CNT[2:0] B2 B1 B0 DEFAULT PULSE1_CNT[2:0] The LED Configuration register controls general LED behavior as well as the number of pulses that are sent for the PULSE LED output behavior. Bit 6 - RAMP_ALERT - Determines whether the device will assert the ALERT# pin when LEDs actuated by the LED Output Control register bits have finished their respective behaviors. Interrupts will only be generated if the LED activity is generated by writing the LED Output Control registers. Any LED activity associated with touch detection will not cause an interrupt to be generated when the LED behavior has been finished. SMSC CAP1133 57 DATASHEET Revision 1.32 (01-05-12) 04h 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet `0' (default) - The ALERT# pin will not be asserted when LEDs actuated by the LED Output Control register have finished their programmed behaviors. `1' - The ALERT# pin will be asserted whenever any LED that is actuated by the LED Output Control register has finished its programmed behavior. Bits 5 - 3 - PULSE2_CNT[2:0] - Determines the number of pulses used for the Pulse 2 behavior as shown in Table 5.58. Bits 2 - 0 - PULSE1_CNT[2:0] - Determines the number of pulses used for the Pulse 1 behavior as shown in Table 5.58. Table 5.58 PULSEX_CNT Decode PULSEX_CNT[2:0] 2 1 0 NUMBER OF BREATHS 0 0 0 1 (default - Pulse 2) 0 0 1 2 0 1 0 3 0 1 1 4 1 0 0 5 (default - Pulse 1) 1 0 1 6 1 1 0 7 1 1 1 8 5.36 LED Duty Cycle Registers Table 5.59 LED Duty Cycle Registers ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 90h R/W LED Pulse 1 Duty Cycle P1_MAX_DUTY[3:0] P1_MIN_DUTY[3:0] F0h 91h R/W LED Pulse 2 Duty Cycle P2_MAX_DUTY[3:0] P2_MIN_DUTY[3:0] F0h 92h R/W LED Breathe Duty Cycle BR_MAX_DUTY[3:0] BR_MIN_DUTY[3:0] F0h 93h R/W Direct Duty Cycle DR_MAX_DUTY[3:0] DR_MIN_DUTY[3:0] F0h The LED Duty Cycle registers determine the minimum and maximum duty cycle settings used for the LED for each LED behavior. These settings affect the brightness of the LED when it is fully off and fully on. The LED driver duty cycle will ramp up from the minimum duty cycle to the maximum duty cycle and back down again. Revision 1.32 (01-05-12) 58 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet APPLICATION NOTE: When operating in Direct behavior mode, changes to the Duty Cycle settings will be applied immediately. When operating in Breathe, Pulse 1, or Pulse 2 modes, the LED must be unactuated and then re-actuated before changes to behavior are processed. Bits 7 - 4 - X_MAX_DUTY[3:0] - Determines the maximum PWM duty cycle for the LED drivers as shown in Table 5.60. Bits 3 - 0 - X_MIN_DUTY[3:0] - Determines the minimum PWM duty cycle for the LED drivers as shown in Table 5.60. Table 5.60 LED Duty Cycle Decode X_MAX/MIN_DUTY [3:0] 3 2 1 0 MAXIMUM DUTY CYCLE MINIMUM DUTY CYCLE 0 0 0 0 7% 0% 0 0 0 1 9% 7% 0 0 1 0 11% 9% 0 0 1 1 14% 11% 0 1 0 0 17% 14% 0 1 0 1 20% 17% 0 1 1 0 23% 20% 0 1 1 1 26% 23% 1 0 0 0 30% 26% 1 0 0 1 35% 30% 1 0 1 0 40% 35% 1 0 1 1 46% 40% 1 1 0 0 53% 46% 1 1 0 1 63% 53% 1 1 1 0 77% 63% 1 1 1 1 100% 77% 5.37 LED Direct Ramp Rates Register Table 5.61 LED Direct Ramp Rates Register ADDR R/W REGISTER B7 B6 94h R/W LED Direct Ramp Rates - - B5 B4 B3 RISE_RATE[2:0] B2 B1 B0 FALL_RATE[2:0] DEFAULT 00h The LED Direct Ramp Rates register control the rising and falling edge time of an LED that is configured to operate in Direct behavior mode. The rising edge time corresponds to the amount of time the LED takes to transition from its minimum duty cycle to its maximum duty cycle. Conversely, the SMSC CAP1133 59 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet falling edge time corresponds to the amount of time that the LED takes to transition from its maximum duty cycle to its minimum duty cycle. Bits 5 - 3 - RISE_RATE[2:0] - Determines the rising edge time of an LED when it transitions from its minimum drive state to its maximum drive state as shown in Table 5.62. Bits 2 - 0 - FALL_RATE[2:0] - Determines the falling edge time of an LED when it transitions from its maximum drive state to its minimum drive state as shown in Table 5.62. Table 5.62 Rise / Fall Rate Decode RISE_RATE/ FALL_RATE/ BIT DECODE 2 1 0 RISE / FALL TIME (TRISE / TFALL)) 0 0 0 0 0 0 1 250ms 0 1 0 500ms 0 1 1 750ms 1 0 0 1s 1 0 1 1.25s 1 1 0 1.5s 1 1 1 2s 5.38 LED Off Delay Register Table 5.63 LED Off Delay Register ADDR R/W REGISTER B7 95h R/W LED Off Delay Register - B6 B5 B4 BR_OFF_DLY[2:0] B3 B2 B1 DIR_OFF_DLY[3:0] B0 DEFAULT 00h The LED Off Delay register determines the amount of time that an LED remains at its maximum duty cycle (or minimum as determined by the polarity controls) before it starts to ramp down. If the LED is operating in Breathe mode, this delay is applied at the top of each "breath". If the LED is operating in the Direct mode, this delay is applied when the LED is unactuated. Bits 6 - 4 - BR_OFF_DLY[2:0] - Determines the Breathe behavior mode off delay, which is the amount of time an LED in Breathe behavior mode remains inactive after it finishes a breathe pulse (ramp on and ramp off), as shown in Figure 5.5 (non-inverted polarity LEDx_POL = 1) and Figure 5.6 (inverted polarity LEDx_POL = 0). Available settings are shown in Table 5.64. Revision 1.32 (01-05-12) 60 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet LED Actuated LED Unactuated 100% - Breathe Max Min Cycle * Brightness LED Brightness Breathe Period (BR_PER) 100% - Breathe Min Duty Cycle * Brightness Breathe Off Delay (BR_OFF_DLY) Figure 5.5 Breathe Behavior with Non-Inverted Polarity LED Actuated LED Unactuated Breathe Max Duty Cycle * Brightness LED Brightness Breathe Min Duty Cycle * Brightness Breathe Period (BR_PER) Breathe Off Delay (BR_OFF_DLY) Figure 5.6 Breathe Behavior with Inverted Polarity SMSC CAP1133 61 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table 5.64 Breathe Off Delay Settings BR_OFF_DLY [2:0] 2 1 0 OFF DELAY 0 0 0 0 (default) 0 0 1 0.25s 0 1 0 0.5s 0 1 1 0.75s 1 0 0 1.0s 1 0 1 1.25s 1 1 0 1.5s 1 1 1 2.0s Bits 3 - 0 - DIR_OFF_DLY[3:0] - Determines the turn-off delay, as shown in Table 5.65, for all LEDs that are configured to operate in Direct behavior mode. The Direct behavior operation is determined by the combination of programmed Rise Time, Fall Time, Min and Max Duty cycles, Off Delay, and polarity. Figure 5.7 shows the behavior for non-inverted polarity (LEDx_POL = 1) while Figure 5.8 shows the behavior for inverted polarity (LEDx_POL = 0). N orm al - untouched operation LE D B rightness Touch D etected R elease D etected N orm al - untouched operation (100% - M in D uty C ycle) * B rightness R IS E _R A TE S etting (t R IS E ) (100% - M ax D uty C ycle) * B rightness O ff D elay (t O FF _D LY ) FA LL_R A TE S etting (t FA LL ) Figure 5.7 Direct Behavior for Non-Inverted Polarity Revision 1.32 (01-05-12) 62 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Release Detected Touch Detected M ax Duty Cycle * Brightness LED Brightness Norm al - untouched operation M in Duty Cycle * Brightness Norm al - untouched operation RISE_RATE Setting (t R ISE ) O ff Delay (t OFF_DLY ) FALL_RATE Setting (t FALL ) Figure 5.8 Direct Behavior for Inverted Polarity Table 5.65 Off Delay Decode OFF DELAY[3:0] BIT DECODE 3 2 1 0 OFF DELAY (TOFF_DLY) 0 0 0 0 0 0 0 0 1 250ms 0 0 1 0 500ms 0 0 1 1 750ms 0 1 0 0 1s 0 1 0 1 1.25s 0 1 1 0 1.5s 0 1 1 1 2s 1 0 0 0 2.5s 1 0 0 1 3.0s 1 0 1 0 3.5s 1 0 1 1 4.0s 1 1 0 0 4.5s All others SMSC CAP1133 5.0s 63 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet 5.39 Sensor Input Calibration Registers Table 5.66 Sensor Input Calibration Registers ADDR REGISTER R/W B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT B1h Sensor Input 1 Calibration R CAL1_9 CAL1_8 CAL1_7 CAL1_6 CAL1_5 CAL1_4 CAL1_3 CAL1_2 00h B2h Sensor Input 2 Calibration R CAL2_9 CAL2_8 CAL2_7 CAL2_6 CAL2_5 CAL2_4 CAL2_3 CAL2_2 00h B3h Sensor Input 3 Calibration R CAL3_9 CAL3_8 CAL3_7 CAL3_6 CAL3_5 CAL3_4 CAL3_3 CAL3_2 00h B9h Sensor Input Calibration LSB 1 R - - CAL3_1 CAL3_0 CAL2_1 CAL2_0 CAL1_1 CAL1_0 00h The Sensor Input Calibration registers hold the 10-bit value that represents the last calibration value. 5.40 Product ID Register Table 5.67 Product ID Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT FDh R Product ID 0 1 0 1 0 1 0 0 54h The Product ID register stores a unique 8-bit value that identifies the device. 5.41 Manufacturer ID Register Table 5.68 Vendor ID Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT FEh R Manufacturer ID 0 1 0 1 1 1 0 1 5Dh The Vendor ID register stores an 8-bit value that represents SMSC. 5.42 Revision Register Table 5.69 Revision Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT FFh R Revision 1 0 0 0 0 0 1 1 83h The Revision register stores an 8-bit value that represents the part revision. Revision 1.32 (01-05-12) 64 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Chapter 6 Package Information 6.1 CAP1133 Package Drawings Figure 6.1 10-Pin DFN 3mm x 3mm Package Drawings SMSC CAP1133 65 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Figure 6.2 10-Pin DFN 3mm x 3mm Package Dimensions Figure 6.3 10-Pin DFN 3mm x 3mm PCB Footprint Revision 1.32 (01-05-12) 66 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet 6.2 Package Marking TOP LINE 1: Device code, First 2 of last 6 digits of Lot Number 1 A 2x 0.6 LINE 2: Last 4 digits of Lot Number e4 PB-FREE/GREEN SYMBOL (Ni/Pd PP-LF) PIN 1 LINES 1 & 2: CENTER HORIZONTAL ALIGNMENT LINE 3: AS SHOWN BOTTOM BOTTOM MARKING IS NOT ALLOWED Figure 6.4 CAP1133 Package Marking SMSC CAP1133 67 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Appendix A Device Delta A.1 Delta from CAP1033 to CAP1133 1. Updated circuitry to improve power supply rejection. 2. Updated LED driver duty cycle decode values to have more distribution at lower values - closer to a logarithmic curve. See Table 5.60, "LED Duty Cycle Decode". 3. Updated bug that breathe periods were not correct above 2.6s. This includes rise / fall time decodes above 1.5s. 4. Added 1 bit to the LED Off Delay register (see Section 5.38, "LED Off Delay Register") to extend times from 2s to 5s in 0.5s intervals. 5. Breathe behavior modified. A breathe off delay control was added to the LED Off Delay Register (see Section 5.38, "LED Off Delay Register") so the LEDs can be configured to remain inactive between breathes. 6. Added controls for the LED transition effects when linking LEDs to capacitive sensor inputs. See Section 5.29, "Linked LED Transition Control Register". 7. Added controls to "mirror" the LED duty cycle outputs so that when polarity changes, the LED brightness levels look right. These bits are automatically set when polarity is set. Added control to break this auto-set behavior. See Section 5.30, "LED Mirror Control Register". 8. Added Multiple Touch Pattern detection circuitry. See Section 5.15, "Multiple Touch Pattern Configuration Register". 9. Added General Status register to flag Multiple touches, Multiple Touch Pattern issues and general touch detections. See Section 5.2, "Status Registers". 10. Added bits 6 and 5 to the Recalibration Configuration register (2Dh - see Section 5.17, "Recalibration Configuration Register"). These bits control whether the accumulation of intermediate data and the consecutive negative delta counts counter are cleared when the noise status bit is set. 11. Added Configuration 2 register for LED linking controls, noise detection controls, and control to interrupt on press but not on release. Added control to change alert pin polarity. See Section 5.6, "Configuration Registers". 12. Updated Deep Sleep behavior so that device does not clear DSLEEP bit on received communications but will wake to communicate. 13. Changed PWM frequency for LED drivers. The PWM frequency was derived from the programmed breathe period and duty cycle settings and it ranged from ~4Hz to ~8000 Hz. The PWM frequency has been updated to be a fixed value of ~2000Hz. 14. Register delta: Table A.1 Register Delta From CAP1033 to CAP1133 ADDRESS REGISTER DELTA DELTA DEFAULT 00h Page 26 Changed - Main Status / Control added bits 7-6 to control gain 00h 02h Page 27 New - General Status new register to store MTP, MULT, LED, and general TOUCH bits 00h Revision 1.32 (01-05-12) 68 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table A.1 Register Delta From CAP1033 to CAP1133 (continued) ADDRESS REGISTER DELTA DELTA DEFAULT 44h Page 31 New - Configuration 2 new register to control alert polarity, LED touch linking behavior, LED output behavior, and noise detection, and interrupt on release 40h 24h Page 36 Changed - Averaging Control updated register bits - moved SAMP_AVG[2:0] bits and added SAMP_TIME bit 1. Default changed 39h 2Bh Page 39 New - Multiple Touch Pattern Configuration new register for Multiple Touch Pattern configuration - enable and threshold settings 80h 2Dh Page 41 New - Multiple Touch Pattern Register new register for Multiple Touch Pattern detection circuitry - pattern or number of sensor inputs 07h 2Fh Page 41 Changed Recalibration Configuration updated register - updated CAL_CFG bit decode to add a 128 averages setting and removed highest time setting. Default changed. Added bit 6 NO_CLR_INTD and bit 5 NO_CLR_NEG. 8Ah 38h Page 43 Changed - Sensor Input Noise Threshold updated register bits - removed bits 7 - 3 and consolidated all controls into bits 1 0. These bits will set the noise threshold for all channels. Default changed 01h 39h Removed - Noise Threshold Register 2 removed register n/a 41h Page 44 Changed - Standby Configuration updated register bits - moved STBY_AVG[2:0] bits and added STBY_TIME bit 1. Default changed 39h 77h Page 51 New - Linked LED Transition Control new register to control transition effect when LED linked to sensor inputs 00h 79h Page 52 New - LED Mirror Control new register to control LED output mirroring for brightness control when polarity changed 00h 90h Page 58 Changed - LED Pulse 1 Duty Cycle changed bit decode to be more logarithmic F0h 91h Page 58 Changed - LED Pulse 2 Duty Cycle changed bit decode to be more logarithmic F0h 92h Page 58 Changed - LED Breathe Duty Cycle changed bit decode to be more logarithmic F0h 93h Page 58 Changed - LED Direct Duty Cycle changed bit decode to be more logarithmic F0h 95h Added controls - LED Off Delay Added bits 6-4 BR_OFF_DLY[2:0] Added bit 3 DIR_OFF_DLY[3] 00h FDh Page 64 Changed - Product ID Changed bit decode for CAP1133 54h SMSC CAP1133 69 DATASHEET Revision 1.32 (01-05-12) 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Chapter 7 Datasheet Revision History Table 7.1 Customer Revision History REVISION LEVEL & DATE Rev. 1.32 (01-05-12) Rev. 1.31 (08-18-11) Rev. 1.3 (05-18-11) Rev. 1.2 (02-10-11) Rev. 1.1 (11-17-10) Revision 1.32 (01-05-12) SECTION/FIGURE/ENTRY CORRECTION Table 2.2, "Electrical Specifications" Added conditions for tHD:DAT. Section 3.2.7, "SMBus and I2C Compatibility" Renamed from "SMBus and I2C Compliance." First paragraph, added last sentence: "For information on using the CAP1133 in an I2C system, refer to SMSC AN 14.0 SMSC Dedicated Slave Devices in I2C Systems." Added: CAP1133 supports I2C fast mode at 400kHz. This covers the SMBus max time of 100kHz. Section 5.4, "Sensor Input Delta Count Registers" Changed negative value cap from FFh to 80h. Section 3.3.3, "SMBus Send Byte" Added an application note: The Send Byte protocol is not functional in Deep Sleep (i.e., DSLEEP bit is set). Section 3.3.4, "SMBus Receive Byte" Added an application note: The Receive Byte protocol is not functional in Deep Sleep (i.e., DSLEEP bit is set). Section 5.2, "Status Registers" Removed RESET as bit 3 in register 02h. Section 5.42, "Revision Register" Updated revision ID from 82h to 83h. Section 5.2, "Status Registers" Added RESET as bit 3 in register 02h. Section A.8, "Delta from Rev B (Mask B0) to Rev C (Mask B1)" Added. Table 2.2, "Electrical Specifications" PSR improvements made in functional revision B. Changed PSR spec from 100 typ and 200 max counts / V to 3 and 10 counts / V. Conditions updated. Section 4.3.2, "Recalibrating Sensor Inputs" Added more detail with subheadings for each type of recalibration. Section 5.6, "Configuration Registers" Added bit 5 BLK_PWR_CTRL to the Configuration 2 Register 44h. The TIMEOUT bit is set to `1' by default for functional revision B and is set to `0' by default for functional revision C. Section 5.42, "Revision Register" Updated revision ID in register FFh from 81h to 82h. Document Updated for functional revision B. See Section A.7, "Delta from Rev A (Mask A0) to Rev B (Mask B0)". 70 DATASHEET SMSC CAP1133 3 Channel Capacitive Touch Sensor with 3 LED Drivers Datasheet Table 7.1 Customer Revision History (continued) REVISION LEVEL & DATE SECTION/FIGURE/ENTRY Cover CORRECTION Added to General Description: "includes circuitry and support for enhanced sensor proximity detection." Added the following Features: Rev. 1.0 (06-14-10) SMSC CAP1133 Calibrates for Parasitic Capacitance Analog Filtering for System Noise Sources Press and Hold feature for Volume-like Applications Table 2.2, "Electrical Specifications" Conditions for Power Supply Rejection modified adding the following: Sampling time = 2.56ms Averaging = 1 Negative Delta Counts = Disabled All other parameters default Section 5.11, "Calibration Activate Register" Updated register description to indicate which recalibration routine is used. Section 5.14, "Multiple Touch Configuration Register" Updated register description to indicate what will happen. Table 5.34, "CSx_BN_TH Bit Decode" Table heading changed from "Threshold Divide Setting" to "Percent Threshold Setting". Initial release 71 DATASHEET Revision 1.32 (01-05-12) Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Microchip: CAP1133-1-AIA-TR