*CORE M* ORE M*CO E M*CORE Freescale Semiconductor, Inc. MMC2107/D REV 2 MMC2107 Technical Data HCMOS Microcontroller Unit Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... blank For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. MMC2107 Freescale Semiconductor, Inc... Technical Data Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Motorola and are registered trademarks of Motorola, Inc. DigitalDNA is a trademark of Motorola, Inc. MMC2107 - Rev. 2.0 (c) Motorola, Inc., 2000 Technical Data MOTOROLA 3 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Technical Data Technical Data MMC2107 - Rev. 2.0 4 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Technical Data -- MMC2107 List of Sections Section 1. General Description . . . . . . . . . . . . . . . . . . . . 43 Freescale Semiconductor, Inc... Section 2. System Memory Map . . . . . . . . . . . . . . . . . . . 51 Section 3. Chip Configuration Module (CCM) . . . . . . . . 89 Section 4. Signal Description. . . . . . . . . . . . . . . . . . . . . 107 Section 5. Reset Controller Module. . . . . . . . . . . . . . . . 129 Section 6. M*CORE M210 Central Processor Unit (CPU) . . . . . . . . . . . . . . . . . . . . . . . . . . 143 Section 7. Interrupt Controller Module . . . . . . . . . . . . . 153 Section 8. Static Random-Access Memory (SRAM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 Section 9. Non-Volatile Memory FLASH (CMFR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 Section 10. Clock Module . . . . . . . . . . . . . . . . . . . . . . . . 221 Section 11. Ports Module . . . . . . . . . . . . . . . . . . . . . . . . 247 Section 12. Edge Port Module (EPORT) . . . . . . . . . . . . 261 Section 13. Watchdog Timer Module . . . . . . . . . . . . . . 271 Section 14. Programmable Interrupt Timer Modules (PIT1 and PIT2) . . . . . . . . . . . . . . 281 Section 15. Timer Modules (TIM1 and TIM2). . . . . . . . . 293 MMC2107 - Rev. 2.0 MOTOROLA Technical Data List of Sections For More Information On This Product, Go to: www.freescale.com 5 Freescale Semiconductor, Inc. List of Sections Section 16. Serial Communications Interface Modules (SCI1 and SCI2) . . . . . . . . . . . . . . 329 Section 17. Serial Peripheral Interface Module (SPI) . . . . . . . . . . . . . . . . . . . . . . . . 371 Section 18. Queued Analog-to-Digital Converter (QADC) . . . . . . . . . . . . . . . . . . . . 399 Freescale Semiconductor, Inc... Section 19. External Bus Interface Module (EBI) . . . . . 503 Section 20. Chip Select Module . . . . . . . . . . . . . . . . . . . 521 Section 21. JTAG Test Access Port and OnCE . . . . . . 533 Section 22. Electrical Specifications. . . . . . . . . . . . . . . 585 Section 23. Mechanical Specifications . . . . . . . . . . . . . 609 Section 24. Ordering Information . . . . . . . . . . . . . . . . . 615 Technical Data 6 MMC2107 - Rev. 2.0 List of Sections For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Table of Contents Freescale Semiconductor, Inc... Section 1. General Description 1.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 1.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 1.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 1.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Section 2. System Memory Map 2.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 2.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 2.3 Address Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 2.4 Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 Section 3. Chip Configuration Module (CCM) 3.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 3.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 3.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 3.4 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90 3.4.1 Master Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 3.4.2 Single-Chip Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 3.4.3 Emulation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 3.4.4 Factory Access Slave Test (FAST) Mode . . . . . . . . . . . . . . 91 3.5 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 3.6 Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Table of Contents For More Information On This Product, Go to: www.freescale.com 7 Freescale Semiconductor, Inc. Table of Contents 3.7 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 3.7.1 Programming Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 3.7.2 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 3.7.3 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 3.7.3.1 Chip Configuration Register . . . . . . . . . . . . . . . . . . . . . . . 94 3.7.3.2 Reset Configuration Register . . . . . . . . . . . . . . . . . . . . . . 97 3.7.3.3 Chip Identification Register . . . . . . . . . . . . . . . . . . . . . . . 99 3.7.3.4 Chip Test Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Freescale Semiconductor, Inc... 3.8 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 3.8.1 Reset Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 3.8.2 Chip Mode Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 3.8.3 Boot Device Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 3.8.4 Output Pad Strength Configuration . . . . . . . . . . . . . . . . . .105 3.8.5 Clock Mode Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 3.8.6 Internal FLASH Configuration . . . . . . . . . . . . . . . . . . . . . . 106 3.9 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 3.10 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 Section 4. Signal Description 4.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 4.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 4.3 Package Pinout Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 4.4 MMC2107 Specific Implementation Signal Issues . . . . . . . . .120 4.4.1 RSTOUT Signal Functions . . . . . . . . . . . . . . . . . . . . . . . . . 120 4.4.2 INT Signal Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 4.5 Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121 4.5.1 Reset Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 4.5.1.1 Reset In (RESET) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 4.5.1.2 Reset Out (RSTOUT). . . . . . . . . . . . . . . . . . . . . . . . . . . 121 4.5.2 Phase-Lock Loop (PLL) and Clock Signals . . . . . . . . . . . . 122 4.5.2.1 External Clock In (EXTAL) . . . . . . . . . . . . . . . . . . . . . . .122 4.5.2.2 Crystal (XTAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 4.5.2.3 Clock Out (CLKOUT) . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 4.5.2.4 Synthesizer Power (VDDSYN and VSSSYN) . . . . . . . . . . . 122 Technical Data 8 MMC2107 - Rev. 2.0 Table of Contents For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Table of Contents Freescale Semiconductor, Inc... 4.5.3 4.5.3.1 4.5.3.2 4.5.3.3 4.5.3.4 4.5.3.5 4.5.3.6 4.5.3.7 4.5.3.8 4.5.3.9 4.5.3.10 4.5.3.11 4.5.4 4.5.4.1 4.5.4.2 4.5.4.3 4.5.5 4.5.5.1 4.5.5.2 4.5.5.3 4.5.5.4 4.5.6 4.5.6.1 4.5.6.2 4.5.7 4.5.8 4.5.8.1 4.5.8.2 4.5.8.3 4.5.8.4 4.5.9 4.5.9.1 4.5.9.2 4.5.9.3 4.5.9.4 4.5.9.5 4.5.9.6 External Memory Interface Signals . . . . . . . . . . . . . . . . . .122 Data Bus (D[31:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 Show Cycle Strobe (SHS) . . . . . . . . . . . . . . . . . . . . . . .123 Transfer Acknowledge (TA) . . . . . . . . . . . . . . . . . . . . . . 123 Transfer Error Acknowledge (TEA) . . . . . . . . . . . . . . . . 123 Emulation Mode Chip Selects (CSE[1:0]) . . . . . . . . . . . 123 Transfer Code (TC[2:0]) . . . . . . . . . . . . . . . . . . . . . . . . . 123 Read/Write (R/W). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 Address Bus (A[22:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . 124 Enable Byte (EB[3:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . 124 Chip Select (CS[3:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 Output Enable (OE) . . . . . . . . . . . . . . . . . . . . . . . . . . . .124 Edge Port Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 External Interrupts (INT[7:6]) . . . . . . . . . . . . . . . . . . . . . 124 External Interrupts (INT[5:2]) . . . . . . . . . . . . . . . . . . . . . 124 External Interrupts (INT[1:0]) . . . . . . . . . . . . . . . . . . . . . 125 Serial Peripheral Interface Module Signals . . . . . . . . . . . . 125 Master Out/Slave In (MOSI). . . . . . . . . . . . . . . . . . . . . . 125 Master In/Slave Out (MISO). . . . . . . . . . . . . . . . . . . . . . 125 Serial Clock (SCK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 Slave Select (SS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 Serial Communications Interface Module Signals . . . . . . . 125 Receive Data (RXD1 and RXD2) . . . . . . . . . . . . . . . . . . 125 Transmit Data (TXD1 and TXD2). . . . . . . . . . . . . . . . . . 126 Timer Signals (ICOC1[3:0] and ICOC2[3:0]) . . . . . . . . . . . 126 Analog-to-Digital Converter Signals . . . . . . . . . . . . . . . . . . 126 Analog Inputs (PQA[4:3], PQA[1:0], and PQB[3:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 Analog Reference (VRH and VRL) . . . . . . . . . . . . . . . . . 126 Analog Supply (VDDA and VSSA) . . . . . . . . . . . . . . . . . .126 Positive Supply (VDDH) . . . . . . . . . . . . . . . . . . . . . . . . . 126 Debug and Emulation Support Signals . . . . . . . . . . . . . . . 127 Test Reset (TRST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 Test Clock (TCLK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 Test Mode Select (TMS) . . . . . . . . . . . . . . . . . . . . . . . . 127 Test Data Input (TDI) . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 Test Data Output (TDO). . . . . . . . . . . . . . . . . . . . . . . . . 127 Debug Event (DE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Table of Contents For More Information On This Product, Go to: www.freescale.com 9 Freescale Semiconductor, Inc. Table of Contents 4.5.10 Test Signal (TEST). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 4.5.11 Power and Ground Signals . . . . . . . . . . . . . . . . . . . . . . . . 128 4.5.11.1 Power for FLASH Erase/Program (VPP) . . . . . . . . . . . . 128 4.5.11.2 Power and Ground for FLASH Array (VDDF and VSSF) . . . . . . . . . . . . . . . . . . . . . . . . . . . .128 4.5.11.3 Standby Power (VSTBY) . . . . . . . . . . . . . . . . . . . . . . . . . 128 4.5.11.4 Positive Supply (VDD). . . . . . . . . . . . . . . . . . . . . . . . . . . 128 4.5.11.5 Ground (VSS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128 Freescale Semiconductor, Inc... Section 5. Reset Controller Module 5.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 5.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 5.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 5.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 5.5 Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 5.6 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 132 5.6.1 Reset Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . .133 5.6.2 Reset Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 5.6.3 Reset Test Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 5.7 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 5.7.1 Reset Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 5.7.1.1 Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 5.7.1.2 External Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 5.7.1.3 Watchdog Timer Reset . . . . . . . . . . . . . . . . . . . . . . . . . 137 5.7.1.4 Loss of Clock Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . .137 5.7.1.5 Loss of Lock Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 5.7.1.6 Software Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 5.7.2 Reset Control Flow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 5.7.2.1 Synchronous Reset Requests . . . . . . . . . . . . . . . . . . . . 138 5.7.2.2 Internal Reset Request . . . . . . . . . . . . . . . . . . . . . . . . . 140 5.7.2.3 Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 5.7.3 Concurrent Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 5.7.3.1 Reset Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 5.7.3.2 Reset Status Flags. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 5.8 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 Technical Data 10 MMC2107 - Rev. 2.0 Table of Contents For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Table of Contents Freescale Semiconductor, Inc... Section 6. M*CORE M210 Central Processor Unit (CPU) 6.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 6.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 6.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 6.4 Microarchitecture Summary . . . . . . . . . . . . . . . . . . . . . . . . . . 145 6.5 Programming Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 6.6 Data Format Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 6.7 Operand Addressing Capabilities . . . . . . . . . . . . . . . . . . . . . . 150 6.8 Instruction Set Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 Section 7. Interrupt Controller Module 7.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 7.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 7.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 7.4 Low-Power Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 154 7.5 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 7.6 External Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 7.7 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 155 7.7.1 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 7.7.2 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157 7.7.2.1 Interrupt Control Register. . . . . . . . . . . . . . . . . . . . . . . . 157 7.7.2.2 Interrupt Status Register . . . . . . . . . . . . . . . . . . . . . . . . 159 7.7.2.3 Interrupt Force Registers . . . . . . . . . . . . . . . . . . . . . . . . 160 7.7.2.4 Interrupt Pending Register . . . . . . . . . . . . . . . . . . . . . . .162 7.7.2.5 Normal Interrupt Enable Register. . . . . . . . . . . . . . . . . . 163 7.7.2.6 Normal Interrupt Pending Register. . . . . . . . . . . . . . . . . 164 7.7.2.7 Fast Interrupt Enable Register . . . . . . . . . . . . . . . . . . . . 165 7.7.2.8 Fast Interrupt Pending Register . . . . . . . . . . . . . . . . . . .166 7.7.2.9 Priority Level Select Registers . . . . . . . . . . . . . . . . . . . . 167 7.8 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 7.8.1 Interrupt Sources and Prioritization . . . . . . . . . . . . . . . . . .168 7.8.2 Fast and Normal Interrupt Requests . . . . . . . . . . . . . . . . . 168 7.8.3 Autovectored and Vectored Interrupt Requests . . . . . . . . .169 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Table of Contents For More Information On This Product, Go to: www.freescale.com 11 Freescale Semiconductor, Inc. Table of Contents 7.8.4 7.8.4.1 7.8.4.2 7.8.4.3 7.8.5 Interrupt Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 M*CORE Processor Configuration . . . . . . . . . . . . . . . . . 171 Interrupt Controller Configuration. . . . . . . . . . . . . . . . . . 171 Interrupt Source Configuration . . . . . . . . . . . . . . . . . . . . 172 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Freescale Semiconductor, Inc... Section 8. Static Random-Access Memory (SRAM) 8.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 8.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 8.3 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175 8.4 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 8.5 Standby Power Supply Pin (VSTBY) . . . . . . . . . . . . . . . . . . . . 176 8.6 Standby Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 8.7 Reset Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 8.8 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 Section 9. Non-Volatile Memory FLASH (CMFR) 9.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 9.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 9.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 9.4 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .182 9.4.1 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .182 9.4.2 Disabled Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182 9.5 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 9.6 Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 9.7 Registers and Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . 186 9.7.1 Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .187 9.7.1.1 CMFR Module Configuration Register . . . . . . . . . . . . . .188 9.7.1.2 CMFR Module Test Register . . . . . . . . . . . . . . . . . . . . . 193 9.7.1.3 CMFR High-Voltage Control Register . . . . . . . . . . . . . . 196 9.7.2 Array Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .203 9.7.2.1 Read Page Buffers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203 9.7.2.2 Program Page Buffers . . . . . . . . . . . . . . . . . . . . . . . . . . 204 Technical Data 12 MMC2107 - Rev. 2.0 Table of Contents For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Table of Contents Freescale Semiconductor, Inc... 9.8 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 9.8.1 Master Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 9.8.2 Register Read and Write Operation . . . . . . . . . . . . . . . . . . 205 9.8.3 Array Read Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 9.8.4 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206 9.8.4.1 Program Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207 9.8.4.2 Program Margin Reads . . . . . . . . . . . . . . . . . . . . . . . . . 211 9.8.4.3 Programming Shadow Information. . . . . . . . . . . . . . . . . 212 9.8.4.4 Program Pulse-Width and Amplitude Modulation . . . . . 213 9.8.4.5 Overprogramming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213 9.8.5 Erasing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214 9.8.5.1 Erase Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 9.8.5.2 Erase Margin Reads . . . . . . . . . . . . . . . . . . . . . . . . . . . 218 9.8.5.3 Erasing Shadow Information Words. . . . . . . . . . . . . . . . 219 9.8.6 Erase Pulse Amplitude and Width Modulation . . . . . . . . . . 219 9.8.7 Emulation Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 9.9 Master Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .220 9.10 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 Section 10. Clock Module 10.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 10.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222 10.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222 10.4 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .223 10.4.1 Normal PLL Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 10.4.2 1:1 PLL Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 10.4.3 External Clock Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 10.4.4 Low-Power Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 10.4.4.1 Wait and Doze Modes . . . . . . . . . . . . . . . . . . . . . . . . . . 223 10.4.4.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 10.5 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 10.6 Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .225 10.6.1 EXTAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 10.6.2 XTAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 10.6.3 CLKOUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Table of Contents For More Information On This Product, Go to: www.freescale.com 13 Freescale Semiconductor, Inc. Table of Contents 10.6.4 10.6.5 VDDSYN and VSSSYN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 RSTOUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226 10.7 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 226 10.7.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226 10.7.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 10.7.2.1 Synthesizer Control Register . . . . . . . . . . . . . . . . . . . . . 227 10.7.2.2 Synthesizer Status Register. . . . . . . . . . . . . . . . . . . . . . 230 10.7.2.3 Synthesizer Test Register . . . . . . . . . . . . . . . . . . . . . . .233 10.7.2.4 Synthesizer Test Register 2 . . . . . . . . . . . . . . . . . . . . . . 234 Freescale Semiconductor, Inc... 10.8 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235 10.8.1 System Clock Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235 10.8.2 System Clocks Generation. . . . . . . . . . . . . . . . . . . . . . . . . 236 10.8.3 PLL Lock Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236 10.8.3.1 PLL Loss of Lock Conditions . . . . . . . . . . . . . . . . . . . . . 238 10.8.3.2 PLL Loss of Lock Reset . . . . . . . . . . . . . . . . . . . . . . . . . 238 10.8.4 Loss of Clock Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . 238 10.8.4.1 Alternate Clock Selection . . . . . . . . . . . . . . . . . . . . . . . . 239 10.8.4.2 Loss-of-Clock Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . .242 10.8.5 Clock Operation During Reset . . . . . . . . . . . . . . . . . . . . . . 243 10.8.6 PLL Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243 10.8.6.1 Phase and Frequency Detector (PFD). . . . . . . . . . . . . .245 10.8.6.2 Charge Pump/Loop Filter . . . . . . . . . . . . . . . . . . . . . . . . 245 10.8.6.3 Voltage Control Output (VCO) . . . . . . . . . . . . . . . . . . . . 246 10.8.6.4 Multiplication Factor Divider (MFD) . . . . . . . . . . . . . . . . 246 10.9 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246 10.10 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246 Section 11. Ports Module 11.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247 11.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248 11.3 Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249 11.4 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 249 11.4.1 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250 11.4.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251 11.4.2.1 Port Output Data Registers . . . . . . . . . . . . . . . . . . . . . . 251 11.4.2.2 Port Data Direction Registers. . . . . . . . . . . . . . . . . . . . . 252 Technical Data 14 MMC2107 - Rev. 2.0 Table of Contents For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Table of Contents 11.4.2.3 11.4.2.4 11.4.2.5 11.4.2.6 Port Pin Data/Set Data Registers . . . . . . . . . . . . . . . . . 253 Port Clear Output Data Registers . . . . . . . . . . . . . . . . . 254 Port C/D Pin Assignment Register . . . . . . . . . . . . . . . . . 255 Port E Pin Assignment Register. . . . . . . . . . . . . . . . . . .256 11.5 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 11.5.1 Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258 11.5.2 Port Digital I/O Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259 Freescale Semiconductor, Inc... 11.6 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259 Section 12. Edge Port Module (EPORT) 12.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261 12.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261 12.3 Low-Power Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 262 12.3.1 Wait and Doze Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262 12.3.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .263 12.4 Interrupt/General-Purpose I/O Pin Descriptions . . . . . . . . . . . 263 12.5 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 263 12.5.1 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263 12.5.2 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264 12.5.2.1 EPORT Pin Assignment Register . . . . . . . . . . . . . . . . . 264 12.5.2.2 EPORT Data Direction Register. . . . . . . . . . . . . . . . . . .266 12.5.2.3 Edge Port Interrupt Enable Register . . . . . . . . . . . . . . . 267 12.5.2.4 Edge Port Data Register . . . . . . . . . . . . . . . . . . . . . . . . 268 12.5.2.5 Edge Port Pin Data Register . . . . . . . . . . . . . . . . . . . . . 268 12.5.2.6 Edge Port Flag Register. . . . . . . . . . . . . . . . . . . . . . . . . 269 Section 13. Watchdog Timer Module 13.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271 13.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271 13.3 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .272 13.3.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .272 13.3.2 Doze Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .272 13.3.3 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .272 13.3.4 Debug Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Table of Contents For More Information On This Product, Go to: www.freescale.com 15 Freescale Semiconductor, Inc. Table of Contents 13.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273 13.5 Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273 Freescale Semiconductor, Inc... 13.6 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 274 13.6.1 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274 13.6.2 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274 13.6.2.1 Watchdog Control Register . . . . . . . . . . . . . . . . . . . . . . 275 13.6.2.2 Watchdog Modulus Register . . . . . . . . . . . . . . . . . . . . . 277 13.6.2.3 Watchdog Count Register . . . . . . . . . . . . . . . . . . . . . . .278 13.6.2.4 Watchdog Service Register . . . . . . . . . . . . . . . . . . . . . . 279 Section 14. Programmable Interrupt Timer Modules (PIT1 and PIT2) 14.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281 14.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282 14.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282 14.4 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .283 14.4.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .283 14.4.2 Doze Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .283 14.4.3 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .283 14.4.4 Debug Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283 14.5 Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283 14.6 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 284 14.6.1 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284 14.6.2 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284 14.6.2.1 PIT Control and Status Register . . . . . . . . . . . . . . . . . .285 14.6.2.2 PIT Modulus Register . . . . . . . . . . . . . . . . . . . . . . . . . . 288 14.6.2.3 PIT Count Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289 14.7 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290 14.7.1 Set-and-Forget Timer Operation . . . . . . . . . . . . . . . . . . . . 290 14.7.2 Free-Running Timer Operation . . . . . . . . . . . . . . . . . . . . . 291 14.7.3 Timeout Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .291 14.8 Interrupt Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292 Technical Data 16 MMC2107 - Rev. 2.0 Table of Contents For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Table of Contents Section 15. Timer Modules (TIM1 and TIM2) 15.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293 15.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295 15.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295 15.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296 Freescale Semiconductor, Inc... 15.5 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .297 15.5.1 Supervisor and User Modes. . . . . . . . . . . . . . . . . . . . . . . . 297 15.5.2 Run Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297 15.5.3 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .297 15.5.4 Wait, Doze, and Debug Modes . . . . . . . . . . . . . . . . . . . . . 297 15.5.5 Test Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .297 15.6 Signal Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298 15.6.1 ICOC[2:0] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298 15.6.2 ICOC3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298 15.7 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 298 15.7.1 Timer Input Capture/Output Compare Select Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 15.7.2 Timer Compare Force Register . . . . . . . . . . . . . . . . . . . . . 301 15.7.3 Timer Output Compare 3 Mask Register . . . . . . . . . . . . . . 302 15.7.4 Timer Output Compare 3 Data Register. . . . . . . . . . . . . . . 303 15.7.5 Timer Counter Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 304 15.7.6 Timer System Control Register 1 . . . . . . . . . . . . . . . . . . . . 305 15.7.7 Timer Toggle-On-Overflow Register . . . . . . . . . . . . . . . . . 306 15.7.8 Timer Control Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . 307 15.7.9 Timer Control Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . 308 15.7.10 Timer Interrupt Enable Register . . . . . . . . . . . . . . . . . . . . . 309 15.7.11 Timer System Control Register 2 . . . . . . . . . . . . . . . . . . . . 310 15.7.12 Timer Flag Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312 15.7.13 Timer Flag Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313 15.7.14 Timer Channel Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 314 15.7.15 Pulse Accumulator Control Register . . . . . . . . . . . . . . . . . 315 15.7.16 Pulse Accumulator Flag Register . . . . . . . . . . . . . . . . . . . . 317 15.7.17 Pulse Accumulator Counter Registers . . . . . . . . . . . . . . . . 318 15.7.18 Timer Port Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . 319 15.7.19 Timer Port Data Direction Register . . . . . . . . . . . . . . . . . .320 15.7.20 Timer Test Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Table of Contents For More Information On This Product, Go to: www.freescale.com 17 Freescale Semiconductor, Inc. Table of Contents 15.8 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321 15.8.1 Prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321 15.8.2 Input Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321 15.8.3 Output Compare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .322 15.8.4 Pulse Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323 15.8.4.1 Event Counter Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 323 15.8.4.2 Gated Time Accumulation Mode . . . . . . . . . . . . . . . . . .324 15.8.5 General-Purpose I/O Ports. . . . . . . . . . . . . . . . . . . . . . . . . 325 15.9 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326 Freescale Semiconductor, Inc... 15.10 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326 15.10.1 Timer Channel Interrupts (CxF) . . . . . . . . . . . . . . . . . . . . . 326 15.10.2 Pulse Accumulator Overflow (PAOVF). . . . . . . . . . . . . . . . 327 15.10.3 Pulse Accumulator Input (PAIF) . . . . . . . . . . . . . . . . . . . . . 327 15.10.4 Timer Overflow (TOF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327 Section 16. Serial Communications Interface Modules (SCI1 and SCI2) 16.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329 16.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330 16.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331 16.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332 16.5 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .333 16.5.1 Doze Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .333 16.5.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .333 16.6 Signal Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334 16.6.1 RXD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334 16.6.2 TXD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334 16.7 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 334 16.7.1 SCI Baud Rate Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 336 16.7.2 SCI Control Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . .337 16.7.3 SCI Control Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . .340 16.7.4 SCI Status Register 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342 16.7.5 SCI Status Register 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344 16.7.6 SCI Data Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345 16.7.7 SCI Pullup and Reduced Drive Register . . . . . . . . . . . . . . 346 Technical Data 18 MMC2107 - Rev. 2.0 Table of Contents For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Table of Contents 16.7.8 16.7.9 SCI Port Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . .347 SCI Data Direction Register . . . . . . . . . . . . . . . . . . . . . . . . 348 16.8 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349 16.9 Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349 16.10 Baud Rate Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 Freescale Semiconductor, Inc... 16.11 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351 16.11.1 Frame Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352 16.11.2 Transmitting a Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353 16.11.3 Break Frames. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355 16.11.4 Idle Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355 16.12 Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356 16.12.1 Frame Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356 16.12.2 Receiving a Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356 16.12.3 Data Sampling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357 16.12.4 Framing Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362 16.12.5 Baud Rate Tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362 16.12.5.1 Slow Data Tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . 363 16.12.5.2 Fast Data Tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . 364 16.12.6 Receiver Wakeup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365 16.12.6.1 Idle Input Line Wakeup (WAKE = 0) . . . . . . . . . . . . . . . 365 16.12.6.2 Address Mark Wakeup (WAKE = 1). . . . . . . . . . . . . . . . 365 16.13 Single-Wire Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366 16.14 Loop Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367 16.15 I/O Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368 16.16 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369 16.17 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369 16.17.1 Transmit Data Register Empty . . . . . . . . . . . . . . . . . . . . . . 369 16.17.2 Transmission Complete . . . . . . . . . . . . . . . . . . . . . . . . . . . 369 16.17.3 Receive Data Register Full. . . . . . . . . . . . . . . . . . . . . . . . . 370 16.17.4 Idle Receiver Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370 16.17.5 Overrun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Table of Contents For More Information On This Product, Go to: www.freescale.com 19 Freescale Semiconductor, Inc. Table of Contents Section 17. Serial Peripheral Interface Module (SPI) 17.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371 17.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372 17.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372 17.4 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .373 17.5 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373 Freescale Semiconductor, Inc... 17.6 Signal Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374 17.6.1 MISO (Master In/Slave Out) . . . . . . . . . . . . . . . . . . . . . . . . 374 17.6.2 MOSI (Master Out/Slave In) . . . . . . . . . . . . . . . . . . . . . . . . 374 17.6.3 SCK (Serial Clock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375 17.6.4 SS (Slave Select) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375 17.7 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 375 17.7.1 SPI Control Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376 17.7.2 SPI Control Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378 17.7.3 SPI Baud Rate Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 379 17.7.4 SPI Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381 17.7.5 SPI Data Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382 17.7.6 SPI Pullup and Reduced Drive Register . . . . . . . . . . . . . . 383 17.7.7 SPI Port Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . .384 17.7.8 SPI Port Data Direction Register . . . . . . . . . . . . . . . . . . . . 385 17.8 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386 17.8.1 Master Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387 17.8.2 Slave Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387 17.8.3 Transmission Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . 388 17.8.3.1 Transfer Format When CPHA = 1 . . . . . . . . . . . . . . . . . 388 17.8.3.2 Transfer Format When CPHA = 0 . . . . . . . . . . . . . . . . . 390 17.8.4 SPI Baud Rate Generation. . . . . . . . . . . . . . . . . . . . . . . . . 393 17.8.5 Slave-Select Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393 17.8.6 Bidirectional Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394 17.8.7 Error Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .395 17.8.7.1 Write Collision Error . . . . . . . . . . . . . . . . . . . . . . . . . . . .395 17.8.7.2 Mode Fault Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395 17.8.8 Low-Power Mode Options . . . . . . . . . . . . . . . . . . . . . . . . . 396 17.8.8.1 Run Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396 17.8.8.2 Doze Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396 17.8.8.3 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396 Technical Data 20 MMC2107 - Rev. 2.0 Table of Contents For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Table of Contents 17.9 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397 17.10 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397 17.10.1 SPI Interrupt Flag (SPIF) . . . . . . . . . . . . . . . . . . . . . . . . . . 397 17.10.2 Mode Fault (MODF) Flag . . . . . . . . . . . . . . . . . . . . . . . . . . 397 Freescale Semiconductor, Inc... Section 18. Queued Analog-to-Digital Converter (QADC) 18.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399 18.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 401 18.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 402 18.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 403 18.5 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .404 18.5.1 Debug Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 404 18.5.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .405 18.6 Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405 18.6.1 Port QA Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406 18.6.1.1 Port QA Analog Input Pins . . . . . . . . . . . . . . . . . . . . . . .406 18.6.1.2 Port QA Digital Input/Output Pins . . . . . . . . . . . . . . . . . 407 18.6.2 Port QB Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407 18.6.2.1 Port QB Analog Input Pins . . . . . . . . . . . . . . . . . . . . . . .407 18.6.2.2 Port QB Digital Input Pins . . . . . . . . . . . . . . . . . . . . . . .407 18.6.3 External Trigger Input Pins. . . . . . . . . . . . . . . . . . . . . . . . . 408 18.6.4 Multiplexed Address Output Pins . . . . . . . . . . . . . . . . . . . . 408 18.6.5 Multiplexed Analog Input Pins . . . . . . . . . . . . . . . . . . . . . . 409 18.6.6 Voltage Reference Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . 409 18.6.7 Dedicated Analog Supply Pins . . . . . . . . . . . . . . . . . . . . . . 409 18.7 Memory Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409 18.8 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411 18.8.1 QADC Module Configuration Register . . . . . . . . . . . . . . . . 411 18.8.2 QADC Test Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412 18.8.3 Port Data Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412 18.8.4 Port QA Data Direction Register . . . . . . . . . . . . . . . . . . . . 414 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Table of Contents For More Information On This Product, Go to: www.freescale.com 21 Freescale Semiconductor, Inc. Table of Contents Freescale Semiconductor, Inc... 18.8.5 18.8.5.1 18.8.5.2 18.8.5.3 18.8.6 18.8.6.1 18.8.6.2 18.8.7 18.8.8 18.8.8.1 18.8.8.2 18.8.8.3 Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .416 Control Register 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 416 Control Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419 QADC Control Register 2. . . . . . . . . . . . . . . . . . . . . . . . 422 Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .427 QADC Status Register 0 . . . . . . . . . . . . . . . . . . . . . . . . 427 QADC Status Register 1 . . . . . . . . . . . . . . . . . . . . . . . . 436 Conversion Command Word Table . . . . . . . . . . . . . . . . . .437 Result Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .441 Right-Justified Unsigned Result Register. . . . . . . . . . . . 441 Left-Justified Signed Result Register . . . . . . . . . . . . . . . 442 Left-Justified Unsigned Result Register . . . . . . . . . . . . . 442 18.9 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443 18.9.1 QADC Bus Accessing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443 18.9.2 External Multiplexing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443 18.9.2.1 External Multiplexing Operation . . . . . . . . . . . . . . . . . . .443 18.9.2.2 Module Version Options. . . . . . . . . . . . . . . . . . . . . . . . . 444 18.9.2.3 External Multiplexed Address Configuration . . . . . . . . .446 18.9.3 Analog Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 446 18.9.3.1 Analog-to-Digital Converter Operation . . . . . . . . . . . . . .446 18.9.3.2 Conversion Cycle Times . . . . . . . . . . . . . . . . . . . . . . . . 446 18.9.3.3 Channel Decode and Multiplexer . . . . . . . . . . . . . . . . . . 448 18.9.3.4 Sample Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .448 18.9.3.5 Digital-to-Analog Converter (DAC) Array . . . . . . . . . . . . 449 18.9.3.6 Comparator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449 18.9.3.7 Bias . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449 18.9.3.8 Successive-Approximation Register . . . . . . . . . . . . . . . 449 18.9.3.9 State Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .450 18.10 Digital Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .450 18.10.1 Queue Priority Timing Examples. . . . . . . . . . . . . . . . . . . . 450 18.10.1.1 Queue Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .451 18.10.1.2 Queue Priority Schemes . . . . . . . . . . . . . . . . . . . . . . . . 453 18.10.2 Boundary Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 465 18.10.3 Scan Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 466 18.10.4 Disabled Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 467 18.10.5 Reserved Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 467 Technical Data 22 MMC2107 - Rev. 2.0 Table of Contents For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Table of Contents Freescale Semiconductor, Inc... 18.10.6 Single-Scan Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 467 18.10.6.1 Software-Initiated Single-Scan Mode. . . . . . . . . . . . . . . 468 18.10.6.2 External Trigger Single-Scan Mode . . . . . . . . . . . . . . . . 469 18.10.6.3 External Gated Single-Scan Mode. . . . . . . . . . . . . . . . . 470 18.10.6.4 Interval Timer Single-Scan Mode. . . . . . . . . . . . . . . . . . 470 18.10.7 Continuous-Scan Modes . . . . . . . . . . . . . . . . . . . . . . . . . . 472 18.10.7.1 Software-Initiated Continuous-Scan Mode. . . . . . . . . . . 473 18.10.7.2 External Trigger Continuous-Scan Mode . . . . . . . . . . . . 474 18.10.7.3 External Gated Continuous-Scan Mode . . . . . . . . . . . . 474 18.10.7.4 Periodic Timer Continuous-Scan Mode . . . . . . . . . . . . . 475 18.10.8 QADC Clock (QCLK) Generation . . . . . . . . . . . . . . . . . . . . 476 18.10.9 Periodic/Interval Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . .480 18.10.10 Conversion Command Word Table . . . . . . . . . . . . . . . . . .481 18.10.11 Result Word Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 485 18.11 Pin Connection Considerations . . . . . . . . . . . . . . . . . . . . . . .486 18.11.1 Analog Reference Pins. . . . . . . . . . . . . . . . . . . . . . . . . . . .486 18.11.2 Analog Power Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 486 18.11.3 Conversion Timing Schemes . . . . . . . . . . . . . . . . . . . . . . .488 18.11.4 Analog Supply Filtering and Grounding . . . . . . . . . . . . . . . 490 18.11.5 Accommodating Positive/Negative Stress Conditions . . . .494 18.11.6 Analog Input Considerations . . . . . . . . . . . . . . . . . . . . . . .495 18.11.7 Analog Input Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 497 18.11.7.1 Settling Time for the External Circuit . . . . . . . . . . . . . . . 498 18.11.7.2 Error Resulting from Leakage . . . . . . . . . . . . . . . . . . . . 499 18.12 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 18.12.1 Interrupt Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 18.12.2 Interrupt Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .501 Section 19. External Bus Interface Module (EBI) 19.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503 19.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 504 19.3 Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .505 19.3.1 Data Bus (D[31:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 506 19.3.2 Show Cycle Strobe (SHS) . . . . . . . . . . . . . . . . . . . . . . . . . 506 19.3.3 Transfer Acknowledge (TA) . . . . . . . . . . . . . . . . . . . . . . . . 506 19.3.4 Transfer Error Acknowledge (TEA) . . . . . . . . . . . . . . . . . .506 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Table of Contents For More Information On This Product, Go to: www.freescale.com 23 Freescale Semiconductor, Inc. Table of Contents Freescale Semiconductor, Inc... 19.3.5 19.3.6 19.3.7 19.3.8 19.3.9 19.3.10 19.3.11 19.3.12 19.3.13 Emulation Mode Chip Selects (CSE[1:0]) . . . . . . . . . . . . . 506 Transfer Code (TC[2:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . . 506 Read/Write (R/W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507 Address Bus (A[22:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507 Enable Byte (EB[3:0]). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507 Chip Selects (CS[3:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507 Output Enable (OE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507 Transfer Size (TSIZ[1:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . 507 Processor Status (PSTAT[3:0]) . . . . . . . . . . . . . . . . . . . . . 507 19.4 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 508 19.5 Operand Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 508 19.6 Enable Byte Pins (EB[3:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . . 510 19.7 Bus Master Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 510 19.7.1 Read Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511 19.7.1.1 State 1 (X1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512 19.7.1.2 Optional Wait States (X2W) . . . . . . . . . . . . . . . . . . . . . . 512 19.7.1.3 State 2 (X2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512 19.7.2 Write Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 513 19.7.2.1 State 1 (X1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 514 19.7.2.2 Optional Wait States (X2W) . . . . . . . . . . . . . . . . . . . . . . 514 19.7.2.3 State 2 (X2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 514 19.8 Bus Exception Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 516 19.8.1 Transfer Error Termination . . . . . . . . . . . . . . . . . . . . . . . . . 516 19.8.2 Transfer Abort Termination . . . . . . . . . . . . . . . . . . . . . . . . 516 19.9 Emulation Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 516 19.9.1 Emulation Chip-Selects (CSE[1:0]) . . . . . . . . . . . . . . . . . .516 19.9.2 Internal Data Transfer Display (Show Cycles) . . . . . . . . . . 517 19.9.3 Show Strobe (SHS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 518 19.10 Bus Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 519 19.11 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 520 Section 20. Chip Select Module 20.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 521 20.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 521 20.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 522 Technical Data 24 MMC2107 - Rev. 2.0 Table of Contents For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Table of Contents 20.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 523 20.5 Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 524 20.6 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 524 20.6.1 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 524 20.6.2 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 525 20.7 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530 20.8 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 531 Freescale Semiconductor, Inc... Section 21. JTAG Test Access Port and OnCE 21.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 533 21.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 535 21.3 Top-Level Test Access Port (TAP) . . . . . . . . . . . . . . . . . . . . . 537 21.3.1 Test Clock (TCLK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 538 21.3.2 Test Mode Select (TMS) . . . . . . . . . . . . . . . . . . . . . . . . . . 538 21.3.3 Test Data Input (TDI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 538 21.3.4 Test Data Output (TDO) . . . . . . . . . . . . . . . . . . . . . . . . . . . 538 21.3.5 Test Reset (TRST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 538 21.3.6 Debug Event (DE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 538 21.4 Top-Level TAP Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . .540 21.5 Instruction Shift Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 541 21.5.1 EXTEST Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 541 21.5.2 IDCODE Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 542 21.5.3 SAMPLE/PRELOAD Instruction . . . . . . . . . . . . . . . . . . . . . 543 21.5.4 ENABLE_MCU_ONCE Instruction . . . . . . . . . . . . . . . . . . .543 21.5.5 HIGHZ Instruction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 544 21.5.6 CLAMP Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 544 21.5.7 BYPASS Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 544 21.6 IDCODE Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545 21.7 Bypass Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 546 21.8 Boundary SCAN Register . . . . . . . . . . . . . . . . . . . . . . . . . . . .546 21.9 Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 546 21.10 Non-Scan Chain Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . 547 21.11 Boundary Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 547 21.12 Low-Level TAP (OnCE) Module . . . . . . . . . . . . . . . . . . . . . . .553 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Table of Contents For More Information On This Product, Go to: www.freescale.com 25 Freescale Semiconductor, Inc. Table of Contents 21.13 Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .555 21.13.1 Debug Serial Input (TDI) . . . . . . . . . . . . . . . . . . . . . . . . . . 555 21.13.2 Debug Serial Clock (TCLK) . . . . . . . . . . . . . . . . . . . . . . . . 555 21.13.3 Debug Serial Output (TDO) . . . . . . . . . . . . . . . . . . . . . . . . 555 21.13.4 Debug Mode Select (TMS). . . . . . . . . . . . . . . . . . . . . . . . . 556 21.13.5 Test Reset (TRST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 556 21.13.6 Debug Event (DE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 556 Freescale Semiconductor, Inc... 21.14 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 556 21.14.1 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 557 21.14.2 OnCE Controller and Serial Interface. . . . . . . . . . . . . . . . . 558 21.14.3 OnCE Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . 559 21.14.3.1 Internal Debug Request Input (IDR) . . . . . . . . . . . . . . . 559 21.14.3.2 CPU Debug Request (DBGRQ) . . . . . . . . . . . . . . . . . . .560 21.14.3.3 CPU Debug Acknowledge (DBGACK) . . . . . . . . . . . . . .560 21.14.3.4 CPU Breakpoint Request (BRKRQ). . . . . . . . . . . . . . . . 560 21.14.3.5 CPU Address, Attributes (ADDR, ATTR) . . . . . . . . . . . . 560 21.14.3.6 CPU Status (PSTAT) . . . . . . . . . . . . . . . . . . . . . . . . . . . 560 21.14.3.7 OnCE Debug Output (DEBUG) . . . . . . . . . . . . . . . . . . . 560 21.14.4 OnCE Controller Registers . . . . . . . . . . . . . . . . . . . . . . . . . 561 21.14.4.1 OnCE Command Register . . . . . . . . . . . . . . . . . . . . . . .561 21.14.4.2 OnCE Control Register . . . . . . . . . . . . . . . . . . . . . . . . . 564 21.14.4.3 OnCE Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . 568 21.14.5 OnCE Decoder (ODEC) . . . . . . . . . . . . . . . . . . . . . . . . . . . 570 21.14.6 Memory Breakpoint Logic. . . . . . . . . . . . . . . . . . . . . . . . . . 570 21.14.6.1 Memory Address Latch (MAL) . . . . . . . . . . . . . . . . . . . . 571 21.14.6.2 Breakpoint Address Base Registers . . . . . . . . . . . . . . . 571 21.14.7 Breakpoint Address Mask Registers . . . . . . . . . . . . . . . . . 571 21.14.7.1 Breakpoint Address Comparators . . . . . . . . . . . . . . . . . 572 21.14.7.2 Memory Breakpoint Counters . . . . . . . . . . . . . . . . . . . . 572 21.14.8 OnCE Trace Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 572 21.14.8.1 OnCE Trace Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . 573 21.14.8.2 Trace Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 574 21.14.9 Methods of Entering Debug Mode . . . . . . . . . . . . . . . . . . . 574 21.14.9.1 Debug Request During RESET . . . . . . . . . . . . . . . . . . .574 21.14.9.2 Debug Request During Normal Activity . . . . . . . . . . . . . 575 21.14.9.3 Debug Request During Stop, Doze, or Wait Mode . . . .575 21.14.9.4 Software Request During Normal Activity . . . . . . . . . . . 575 Technical Data 26 MMC2107 - Rev. 2.0 Table of Contents For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Table of Contents Freescale Semiconductor, Inc... 21.14.10 Enabling OnCE Trace Mode . . . . . . . . . . . . . . . . . . . . . . .575 21.14.11 Enabling OnCE Memory Breakpoints. . . . . . . . . . . . . . . . . 576 21.14.12 Pipeline Information and Write-Back Bus Register . . . . . . 576 21.14.12.1 Program Counter Register . . . . . . . . . . . . . . . . . . . . . . .577 21.14.12.2 Instruction Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . 577 21.14.12.3 Control State Register . . . . . . . . . . . . . . . . . . . . . . . . . . 577 21.14.12.4 Writeback Bus Register . . . . . . . . . . . . . . . . . . . . . . . . . 579 21.14.12.5 Processor Status Register . . . . . . . . . . . . . . . . . . . . . . .579 21.14.13 Instruction Address FIFO Buffer (PC FIFO) . . . . . . . . . . . . 580 21.14.14 Reserved Test Control Registers . . . . . . . . . . . . . . . . . . . . 581 21.14.15 Serial Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 581 21.14.16 OnCE Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 582 21.14.17 Target Site Debug System Requirements . . . . . . . . . . . . . 582 21.14.18 Interface Connector for JTAG/OnCE Serial Port . . . . . . . . 582 Section 22. Electrical Specifications 22.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 585 22.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 585 22.3 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . 586 22.4 Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 587 22.5 Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 587 22.6 Electrostatic Discharge (ESD) Protection . . . . . . . . . . . . . . . . 587 22.7 DC Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 588 22.8 PLL Electrical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . 590 22.9 QADC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . .591 22.10 FLASH Memory Characteristics . . . . . . . . . . . . . . . . . . . . . . .594 22.11 External Interface Timing Characteristics . . . . . . . . . . . . . . . . 596 22.12 Reset and Configuration Override Timing . . . . . . . . . . . . . . . 601 22.13 SPI Timing Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . 602 22.14 OnCE, JTAG, and Boundary Scan Timing . . . . . . . . . . . . . . . 605 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Table of Contents For More Information On This Product, Go to: www.freescale.com 27 Freescale Semiconductor, Inc. Table of Contents Freescale Semiconductor, Inc... Section 23. Mechanical Specifications 23.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 609 23.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 609 23.3 Bond Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 610 23.4 Package Information for the 144-Pin LQFP . . . . . . . . . . . . . . 611 23.5 Package Information for the 100-Pin LQFP . . . . . . . . . . . . . . 611 23.6 144-Pin LQFP Mechanical Drawing . . . . . . . . . . . . . . . . . . . . 612 23.7 100-Pin LQFP Mechanical Drawing . . . . . . . . . . . . . . . . . . . . 613 Section 24. Ordering Information 24.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 615 24.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 615 24.3 MC Order Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .615 Technical Data 28 MMC2107 - Rev. 2.0 Table of Contents For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 List of Figures Freescale Semiconductor, Inc... Figure Title 1-1 2-1 2-2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Address Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Register Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 3-1 3-2 3-3 3-4 3-5 Chip Configuration Module Block Diagram . . . . . . . . . . . . . 92 Chip Configuration Register (CCR) . . . . . . . . . . . . . . . . . . .94 Reset Configuration Register (RCON) . . . . . . . . . . . . . . . . . 97 Chip Identification Register (CIR). . . . . . . . . . . . . . . . . . . . . 99 Chip Test Register (CTR). . . . . . . . . . . . . . . . . . . . . . . . . . 100 4-1 4-2 144-Pin LQFP Assignments . . . . . . . . . . . . . . . . . . . . . . . . 115 100-Pin LQFP Assignments . . . . . . . . . . . . . . . . . . . . . . . . 116 5-1 5-2 5-3 5-4 5-5 Reset Controller Block Diagram . . . . . . . . . . . . . . . . . . . . . 131 Reset Control Register (RCR) . . . . . . . . . . . . . . . . . . . . . . 133 Reset Status Register (RSR) . . . . . . . . . . . . . . . . . . . . . . .134 Reset Test Register (RTR). . . . . . . . . . . . . . . . . . . . . . . . . 135 Reset Control Flow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 6-1 6-2 6-3 6-4 M*CORE Processor Block Diagram . . . . . . . . . . . . . . . . . . 145 Programming Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 Data Organization in Memory. . . . . . . . . . . . . . . . . . . . . . .149 Data Organization in Registers . . . . . . . . . . . . . . . . . . . . . 149 7-1 7-2 7-3 7-4 7-5 Interrupt Controller Block Diagram . . . . . . . . . . . . . . . . . . .155 Interrupt Control Register (ICR) . . . . . . . . . . . . . . . . . . . . . 157 Interrupt Status Register (ISR) . . . . . . . . . . . . . . . . . . . . . . 159 Interrupt Force Register High (IFRH) . . . . . . . . . . . . . . . . . 160 Interrupt Force Register Low (IFRL). . . . . . . . . . . . . . . . . . 161 MMC2107 - Rev. 2.0 MOTOROLA Page Technical Data List of Figures For More Information On This Product, Go to: www.freescale.com 29 Freescale Semiconductor, Inc. List of Figures Freescale Semiconductor, Inc... Figure Title 7-6 7-7 7-8 7-9 7-10 7-11 Interrupt Pending Register (IPR) . . . . . . . . . . . . . . . . . . . . 162 Normal Interrupt Enable Register (NIER) . . . . . . . . . . . . . .163 Normal Interrupt Pending Register (NIPR). . . . . . . . . . . . . 164 Fast Interrupt Enable Register (FIER) . . . . . . . . . . . . . . . . 165 Fast Interrupt Pending Register (FIPR) . . . . . . . . . . . . . . . 166 Priority Level Select Registers (PLSR0-PLSR39) . . . . . . . 167 9-1 9-2 9-3 9-4 9-5 9-6 9-7 9-8 9-9 9-10 CMFR 128-Kbyte Block Diagram . . . . . . . . . . . . . . . . . . . . 183 CMFR Array and Control Register Addressing . . . . . . . . .186 CMFR Module Configuration Register (CMFRMCR) . . . . .188 CMFR Module Test Register (CMFRMTR) . . . . . . . . . . . . 193 CMFR High-Voltage Control Register (CMFRCTL) . . . . . . 196 Pulse Status Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197 FLASH Programming Flowchart. . . . . . . . . . . . . . . . . . . . . 209 Program State Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . 210 FLASH Erasing Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . 216 Erase State Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217 10-1 10-2 10-3 10-4 10-5 10-6 10-7 10-8 Clock Module Block Diagram . . . . . . . . . . . . . . . . . . . . . . .224 Synthesizer Control Register (SYNCR) . . . . . . . . . . . . . . . 227 Synthesizer Status Register (SYNSR) . . . . . . . . . . . . . . . . 230 Synthesizer Test Register (SYNTR). . . . . . . . . . . . . . . . . . 233 Synthesizer Test Register 2 (SYNTR2) . . . . . . . . . . . . . . . 234 Lock Detect Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . .237 PLL Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244 Crystal Oscillator Example . . . . . . . . . . . . . . . . . . . . . . . . . 244 11-1 11-2 11-3 11-4 11-5 11-6 Ports Module Block Diagram . . . . . . . . . . . . . . . . . . . . . . .248 Port Output Data Registers (PORTx) . . . . . . . . . . . . . . . . . 251 Port Data Direction Registers (DDRx) . . . . . . . . . . . . . . . . 252 Port Pin Data/Set Data Registers (PORTxP/SETx) . . . . . . 253 Port Clear Output Data Registers (CLRx) . . . . . . . . . . . . . 254 Port C, D, I7, and I6 Pin Assignment Register (PCDPAR). . . . . . . . . . . . . . . . . . . . . . . . . . . .255 Port E Pin Assignment Register (PEPAR) . . . . . . . . . . . . . 256 11-7 Technical Data 30 Page MMC2107 - Rev. 2.0 List of Figures For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. List of Figures Freescale Semiconductor, Inc... Figure Title 11-8 11-9 Digital Input Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259 Digital Output Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259 12-1 12-2 12-3 12-4 12-5 12-6 12-7 EPORT Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . .262 EPORT Pin Assignment Register (EPPAR) . . . . . . . . . . . . 264 EPORT Data Direction Register (EPDDR). . . . . . . . . . . . . 266 EPORT Port Interrupt Enable Register (EPIER) . . . . . . . . 267 EPORT Port Data Register (EPDR) . . . . . . . . . . . . . . . . . . 268 EPORT Port Pin Data Register (EPPDR) . . . . . . . . . . . . . 268 EPORT Port Flag Register (EPFR) . . . . . . . . . . . . . . . . . .269 13-1 13-2 13-3 13-4 13-5 Watchdog Timer Block Diagram. . . . . . . . . . . . . . . . . . . . . 273 Watchdog Control Register (WCR) . . . . . . . . . . . . . . . . . .275 Watchdog Modulus Register (WMR) . . . . . . . . . . . . . . . . . 277 Watchdog Count Register (WCNTR) . . . . . . . . . . . . . . . . . 278 Watchdog Service Register (WSR) . . . . . . . . . . . . . . . . . .279 14-1 14-2 14-3 14-4 14-5 14-6 PIT Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282 PIT Control and Status Register (PCSR) . . . . . . . . . . . . . .285 PIT Modulus Register (PMR) . . . . . . . . . . . . . . . . . . . . . . .288 PIT Count Register (PCNTR) . . . . . . . . . . . . . . . . . . . . . . .289 Counter Reloading from the Modulus Latch. . . . . . . . . . . . 290 Counter in Free-Running Mode . . . . . . . . . . . . . . . . . . . . . 291 15-1 15-2 Timer Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296 Timer Input Capture/Output Compare Select Register (TIMIOS) . . . . . . . . . . . . . . . . . . . . . . .300 Timer Compare Force Register (TIMCFORC) . . . . . . . . . . 301 Timer Output Compare 3 Mask Register (TIMOC3M) . . . .302 Timer Output Compare 3 Data Register (TIMOC3D) . . . . .303 Timer Counter Register High (TIMCNTH) . . . . . . . . . . . . . 304 Timer Counter Register Low (TIMCNTL) . . . . . . . . . . . . . .304 Timer System Control Register (TIMSCR1) . . . . . . . . . . . . 305 Fast Clear Flag Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306 Timer Toggle-On-Overflow Register (TIMTOV) . . . . . . . . .306 Timer Control Register 1 (TIMCTL1) . . . . . . . . . . . . . . . . . 307 15-3 15-4 15-5 15-6 15-7 15-8 15-9 15-10 15-11 MMC2107 - Rev. 2.0 MOTOROLA Page Technical Data List of Figures For More Information On This Product, Go to: www.freescale.com 31 Freescale Semiconductor, Inc. List of Figures Figure Freescale Semiconductor, Inc... 15-12 15-13 15-14 15-15 15-16 15-17 15-18 15-19 15-20 15-21 Title 15-23 15-24 15-25 15-26 Timer Control Register 2 (TIMCTL2) . . . . . . . . . . . . . . . . . 308 Timer Interrupt Enable Register (TIMIE) . . . . . . . . . . . . . . 309 Timer System Control Register 2 (TIMSCR2) . . . . . . . . . . 310 Timer Flag Register 1 (TIMFLG1) . . . . . . . . . . . . . . . . . . . 312 Timer Flag Register 2 (TIMFLG2) . . . . . . . . . . . . . . . . . . . 313 Timer Channel [0:3] Register High (TIMCxH) . . . . . . . . . . 314 Timer Channel [0:3] Register Low (TIMCxL) . . . . . . . . . . . 314 Pulse Accumulator Control Register (TIMPACTL) . . . . . . . 315 Pulse Accumulator Flag Register (TIMPAFLG) . . . . . . . . .317 Pulse Accumulator Counter Register High (TIMPACNTH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318 Pulse Accumulator Counter Register Low (TIMPACNTL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .318 Timer Port Data Register (TIMPORT) . . . . . . . . . . . . . . . . 319 Timer Port Data Direction Register (TIMDDR) . . . . . . . . . . 320 Timer Test Register (TIMTST) . . . . . . . . . . . . . . . . . . . . . . 321 Channel 3 Output Compare/Pulse Accumulator Logic. . . . 324 16-1 16-2 16-3 16-4 16-5 16-6 16-7 16-8 16-9 16-10 16-11 16-12 16-13 16-14 16-15 16-16 16-17 16-18 SCI Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332 SCI Baud Rate Register High (SCIBDH) . . . . . . . . . . . . . . 336 SCI Baud Rate Register Low (SCIBDL) . . . . . . . . . . . . . . . 336 SCI Control Register 1 (SCICR1) . . . . . . . . . . . . . . . . . . . . 337 SCI Control Register 2 (SCICR2) . . . . . . . . . . . . . . . . . . . . 340 SCI Status Register 1 (SCISR1) . . . . . . . . . . . . . . . . . . . . 342 SCI Status Register 2 (SCISR2) . . . . . . . . . . . . . . . . . . . . 344 SCI Data Register High (SCIDRH) . . . . . . . . . . . . . . . . . . .345 SCI Data Register Low (SCIDRL) . . . . . . . . . . . . . . . . . . . 345 SCI Pullup and Reduced Drive Register (SCIPURD). . . . .346 SCI Port Data Register (SCIPORT) . . . . . . . . . . . . . . . . . . 347 SCI Data Direction Register (SCIDDR) . . . . . . . . . . . . . . . 348 SCI Data Formats. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349 Transmitter Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . 351 SCI Receiver Block Diagram . . . . . . . . . . . . . . . . . . . . . . .356 Receiver Data Sampling. . . . . . . . . . . . . . . . . . . . . . . . . . . 357 Start Bit Search Example 1 . . . . . . . . . . . . . . . . . . . . . . . . 359 Start Bit Search Example 2 . . . . . . . . . . . . . . . . . . . . . . . . 360 15-22 Technical Data 32 Page MMC2107 - Rev. 2.0 List of Figures For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. List of Figures Freescale Semiconductor, Inc... Figure Title 16-19 16-20 16-21 16-22 16-23 16-24 16-25 16-26 Start Bit Search Example 3 . . . . . . . . . . . . . . . . . . . . . . . . 360 Start Bit Search Example 4 . . . . . . . . . . . . . . . . . . . . . . . . 361 Start Bit Search Example 5 . . . . . . . . . . . . . . . . . . . . . . . . 361 Start Bit Search Example 6 . . . . . . . . . . . . . . . . . . . . . . . . 362 Slow Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363 Fast Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364 Single-Wire Operation (LOOPS = 1, RSRC = 1) . . . . . . . . 366 Loop Operation (LOOPS = 1, RSRC = 0) . . . . . . . . . . . . . 367 17-1 17-2 17-3 17-4 17-5 17-6 17-7 17-8 17-9 17-10 17-11 17-12 17-13 SPI Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373 SPI Control Register 1 (SPICR1) . . . . . . . . . . . . . . . . . . . . 376 SPI Control Register 2 (SPICR2) . . . . . . . . . . . . . . . . . . . . 378 SPI Baud Rate Register (SPIBR) . . . . . . . . . . . . . . . . . . . . 379 SPI Status Register (SPISR) . . . . . . . . . . . . . . . . . . . . . . .381 SPI Data Register (SPIDR) . . . . . . . . . . . . . . . . . . . . . . . . 382 SPI Pullup and Reduced Drive Register (SPIPURD) . . . . .383 SPI Port Data Register (SPIPORT) . . . . . . . . . . . . . . . . . .384 SPI Port Data Direction Register (SPIDDR). . . . . . . . . . . . 385 Full-Duplex Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386 SPI Clock Format 1 (CPHA = 1). . . . . . . . . . . . . . . . . . . . . 389 SPI Clock Format 0 (CPHA = 0). . . . . . . . . . . . . . . . . . . . . 391 Transmission Error Due to Master/Slave Clock Skew . . . .392 18-1 18-2 18-3 18-4 18-5 18-6 18-7 18-8 18-9 18-10 18-11 18-12 18-13 QADC Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 403 QADC Input and Output Signals . . . . . . . . . . . . . . . . . . . . 406 QADC Module Configuration Register (QADCMCR) . . . . .411 QADC Test Register (QADCTEST) . . . . . . . . . . . . . . . . . .412 QADC Port QA Data Register (PORTQA) . . . . . . . . . . . . . 413 QADC Port QB Data Register (PORTQB) . . . . . . . . . . . . . 413 QADC Port QA Data Direction Register (DDRQA). . . . . . . 415 QADC Control Register 0 (QACR0) . . . . . . . . . . . . . . . . . . 416 QADC Control Register 1 (QACR1) . . . . . . . . . . . . . . . . . . 419 QADC Control Register 2 (QACR2) . . . . . . . . . . . . . . . . . . 422 QADC Status Register 0 (QASR0) . . . . . . . . . . . . . . . . . . .427 Queue Status Transition. . . . . . . . . . . . . . . . . . . . . . . . . . . 435 QADC Status Register 1 (QASR1) . . . . . . . . . . . . . . . . . . .436 MMC2107 - Rev. 2.0 MOTOROLA Page Technical Data List of Figures For More Information On This Product, Go to: www.freescale.com 33 Freescale Semiconductor, Inc. List of Figures Figure Freescale Semiconductor, Inc... 18-14 18-15 18-16 18-17 18-18 18-19 18-20 18-21 18-22 18-23 18-24 18-25 18-26 18-27 18-28 18-29 18-30 18-31 18-32 18-33 18-34 18-35 18-36 18-37 18-38 18-39 18-40 18-41 18-42 18-43 18-44 18-45 18-46 18-47 18-48 Title Conversion Command Word Table (CCW) . . . . . . . . . . . . 437 Right-Justified Unsigned Result Register (RJURR) . . . . . . 441 Left-Justified Signed Result Register (LJSRR) . . . . . . . . .442 Left-Justified Unsigned Result Register (LJURR) . . . . . . . 442 External Multiplexing Configuration . . . . . . . . . . . . . . . . . .445 QADC Analog Subsystem Block Diagram . . . . . . . . . . . . . 447 Conversion Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 447 Bypass Mode Conversion Timing. . . . . . . . . . . . . . . . . . . . 448 QADC Queue Operation with Pause . . . . . . . . . . . . . . . . . 452 CCW Priority Situation 1. . . . . . . . . . . . . . . . . . . . . . . . . . . 455 CCW Priority Situation 2. . . . . . . . . . . . . . . . . . . . . . . . . . . 456 CCW Priority Situation 3. . . . . . . . . . . . . . . . . . . . . . . . . . . 457 CCW Priority Situation 4. . . . . . . . . . . . . . . . . . . . . . . . . . . 457 CCW Priority Situation 5. . . . . . . . . . . . . . . . . . . . . . . . . . . 458 CCW Priority Situation 6. . . . . . . . . . . . . . . . . . . . . . . . . . . 459 CCW Priority Situation 7. . . . . . . . . . . . . . . . . . . . . . . . . . . 459 CCW Priority Situation 8. . . . . . . . . . . . . . . . . . . . . . . . . . . 460 CCW Priority Situation 9. . . . . . . . . . . . . . . . . . . . . . . . . . . 460 CCW Priority Situation 10. . . . . . . . . . . . . . . . . . . . . . . . . . 461 CCW Priority Situation 11. . . . . . . . . . . . . . . . . . . . . . . . . . 461 CCW Freeze Situation 12. . . . . . . . . . . . . . . . . . . . . . . . . . 462 CCW Freeze Situation 13. . . . . . . . . . . . . . . . . . . . . . . . . . 462 CCW Freeze Situation 14. . . . . . . . . . . . . . . . . . . . . . . . . . 463 CCW Freeze Situation 15. . . . . . . . . . . . . . . . . . . . . . . . . . 463 CCW Freeze Situation 16. . . . . . . . . . . . . . . . . . . . . . . . . . 463 CCW Freeze Situation 17. . . . . . . . . . . . . . . . . . . . . . . . . . 464 CCW Freeze Situation 18. . . . . . . . . . . . . . . . . . . . . . . . . . 464 CCW Freeze Situation 19. . . . . . . . . . . . . . . . . . . . . . . . . . 464 QADC Clock Subsystem Functions . . . . . . . . . . . . . . . . . .477 QADC Clock Programmability Examples . . . . . . . . . . . . . .479 QADC Conversion Queue Operation . . . . . . . . . . . . . . . . . 482 Equivalent Analog Input Circuitry . . . . . . . . . . . . . . . . . . . . 487 Errors Resulting from Clipping . . . . . . . . . . . . . . . . . . . . . . 488 External Positive Edge Trigger Mode Timing With Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . 489 Gated Mode, Single Scan Timing. . . . . . . . . . . . . . . . . . . . 491 Technical Data 34 Page MMC2107 - Rev. 2.0 List of Figures For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. List of Figures Freescale Semiconductor, Inc... Figure Title 18-49 18-50 18-51 18-52 18-53 18-54 Gated Mode, Continuous Scan Timing . . . . . . . . . . . . . . . 491 Star-Ground at the Point of Power Supply Origin. . . . . . . . 493 Input Pin Subjected to Negative Stress . . . . . . . . . . . . . . . 494 Input Pin Subjected to Positive Stress . . . . . . . . . . . . . . . . 494 External Multiplexing of Analog Signal Sources. . . . . . . . .496 Electrical Model of an A/D Input Pin. . . . . . . . . . . . . . . . . . 497 19-1 19-2 19-3 19-4 19-5 Read Cycle Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511 Write Cycle Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . 513 Master Mode -- 1-Clock Read and Write Cycle. . . . . . . . .515 Master Mode -- 2-Clock Read and Write Cycle. . . . . . . . .515 Internal (Show) Cycle Followed . . . . . . . . . . . . . . . . . . . . . . . . by External 1-Clock Read . . . . . . . . . . . . . . . . . . . . . . .518 Internal (Show) Cycle Followed by External 1-Clock Write . . . . . . . . . . . . . . . . . . . . . . .519 19-6 20-1 20-2 20-3 20-4 20-5 Chip Select Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . 523 Chip Select Control Register 0 (CSCR0) . . . . . . . . . . . . . .525 Chip Select Control Register 1 (CSCR1) . . . . . . . . . . . . . .526 Chip Select Control Register 2 (CSCR2) . . . . . . . . . . . . . .526 Chip Select Control Register 3 (CSCR3) . . . . . . . . . . . . . .527 21-1 Top-Level Tap Module and Low-Level (OnCE) TAP Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 536 Top-Level TAP Controller State Machine . . . . . . . . . . . . . .540 IDCODE Register Bit Specification . . . . . . . . . . . . . . . . . .545 OnCE Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 553 Low-Level (OnCE) Tap Module Data Registers (DRs). . . . 554 OnCE Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .557 OnCE Controller and Serial Interface. . . . . . . . . . . . . . . . . 559 OnCE Command Register (OCMR) . . . . . . . . . . . . . . . . . . 562 OnCE Control Register (OCR) . . . . . . . . . . . . . . . . . . . . . . 564 OnCE Status Register (OSR) . . . . . . . . . . . . . . . . . . . . . . .568 OnCE Memory Breakpoint Logic . . . . . . . . . . . . . . . . . . . . 570 OnCE Trace Logic Block Diagram . . . . . . . . . . . . . . . . . . .573 CPU Scan Chain Register (CPUSCR) . . . . . . . . . . . . . . . . 576 21-2 21-3 21-4 21-5 21-6 21-7 21-8 21-9 21-10 21-11 21-12 21-13 MMC2107 - Rev. 2.0 MOTOROLA Page Technical Data List of Figures For More Information On This Product, Go to: www.freescale.com 35 Freescale Semiconductor, Inc. List of Figures Freescale Semiconductor, Inc... Figure Title 21-14 21-15 21-16 Control State Register (CTL) . . . . . . . . . . . . . . . . . . . . . . .578 OnCE PC FIFO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 580 Recommended Connector Interface to JTAG/OnCE Port . . . . . . . . . . . . . . . . . . . . . . . . . . . .583 22-1 22-2 22-3 22-4 22-5 22-6 22-7 22-8 22-9 22-10 22-11 22-12 22-13 VPP versus Programming Time . . . . . . . . . . . . . . . . . . . . . 595 VPP versus Programming Pulses . . . . . . . . . . . . . . . . . . . . 595 CLKOUT Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .597 Clock Read/Write Cycle Timing . . . . . . . . . . . . . . . . . . . . . 598 Read/Write Cycle Timing with Wait States. . . . . . . . . . . . . 599 Show Cycle Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600 RESET and Configuration Override Timing . . . . . . . . . . . . 601 SPI Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 603 Test Clock Input Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . 605 Boundary Scan (JTAG) Timing . . . . . . . . . . . . . . . . . . . . . 606 Test Access Port Timing . . . . . . . . . . . . . . . . . . . . . . . . . . 606 TRST Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 606 Debug Event Pin Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . 607 Technical Data 36 Page MMC2107 - Rev. 2.0 List of Figures For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 List of Tables Freescale Semiconductor, Inc... Table Title 2-1 Register Address Location Map . . . . . . . . . . . . . . . . . . . . . . . 53 3-1 3-2 3-3 3-4 3-5 3-6 3-7 3-8 3-9 3-10 3-11 3-12 3-13 Signal Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Write-Once Bits Read/Write Accessibility. . . . . . . . . . . . . . . . 93 Chip Configuration Module Memory Map . . . . . . . . . . . . . . . . 94 Chip Configuration Mode Selection . . . . . . . . . . . . . . . . . . . . 95 Bus Monitor Timeout Values . . . . . . . . . . . . . . . . . . . . . . . . . 97 Reset Configuration Pin States During Reset . . . . . . . . . . . 101 Configuration During Reset . . . . . . . . . . . . . . . . . . . . . . . . . 102 Chip Configuration Mode Selection . . . . . . . . . . . . . . . . . . . 103 Chip Select CS0 Configuration Encoding. . . . . . . . . . . . . . . 104 Boot Device Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 Output Pad Driver Strength Selection . . . . . . . . . . . . . . . . . 105 Clock Mode Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Internal FLASH Configuration. . . . . . . . . . . . . . . . . . . . . . . . 106 4-1 4-2 Package Pinouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 Signal Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 5-1 5-2 5-3 Reset Controller Signal Properties . . . . . . . . . . . . . . . . . . . . 131 Reset Controller Module Memory Map. . . . . . . . . . . . . . . . . 132 Reset Source Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . .136 6-1 M*CORE Instruction Set . . . . . . . . . . . . . . . . . . . . . . . . . . . .150 7-1 7-2 7-3 7-4 Interrupt Controller Module Memory Map. . . . . . . . . . . . . . . 156 MASK Encoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158 Priority Select Encoding . . . . . . . . . . . . . . . . . . . . . . . . . . . .167 Fast Interrupt Vector Number . . . . . . . . . . . . . . . . . . . . . . . . 170 MMC2107 - Rev. 2.0 MOTOROLA Page Technical Data List of Tables For More Information On This Product, Go to: www.freescale.com 37 Freescale Semiconductor, Inc. List of Tables Freescale Semiconductor, Inc... Table Title 7-5 7-6 Vector Table Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 Interrupt Source Assignment . . . . . . . . . . . . . . . . . . . . . . . . 172 9-1 9-2 9-3 9-4 9-5 9-6 Non-Volatile Memory FLASH Memory Map . . . . . . . . . . . . . 187 Negative Voltage Modulation . . . . . . . . . . . . . . . . . . . . . . . . 194 Drain Amplitude Modulation (GDB = 0) . . . . . . . . . . . . . . . . 195 System Clock Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198 Clock Period Exponent and Pulse Width Range . . . . . . . . .199 Determining SCLKR[2:0], CLKPE[1:0], and CLKPM[6:0] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 Program Interlock State Descriptions . . . . . . . . . . . . . . . . . . 210 Results of Programming Margin Read . . . . . . . . . . . . . . . . . 212 Required Programming Algorithm . . . . . . . . . . . . . . . . . . . . 213 Erase Interlock State Descriptions . . . . . . . . . . . . . . . . . . . . 217 Required Erase Algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . 219 9-7 9-8 9-9 9-10 9-11 10-1 10-2 10-3 10-4 10-5 10-6 10-7 10-8 10-9 Signal Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 Clock Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . 226 System Frequency Multiplier of the Reference Frequency in Normal PLL Mode . . . . . . . . . . . . . . . . . . . 228 STPMD[1:0] Operation in Stop Mode . . . . . . . . . . . . . . . . . . 230 System Clock Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231 Clock-Out and Clock-In Relationships . . . . . . . . . . . . . . . . . 235 Loss of Clock Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239 Stop Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240 Charge Pump Current and MFD in Normal Mode Operation . . . . . . . . . . . . . . . . . . . . . . .245 11-1 11-2 11-3 I/O Port Module Memory Map . . . . . . . . . . . . . . . . . . . . . . .250 PEPAR Reset Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256 Ports A-I Supported Pin Functions . . . . . . . . . . . . . . . . . . . 258 12-1 12-2 Edge Port Module Memory Map. . . . . . . . . . . . . . . . . . . . . . 263 EPPAx Field Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265 13-1 Watchdog Timer Module Memory Map . . . . . . . . . . . . . . . . 274 Technical Data 38 Page MMC2107 - Rev. 2.0 List of Tables For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. List of Tables Freescale Semiconductor, Inc... Table Title 14-1 14-2 14-3 Programmable Interrupt Timer Modules Memory Map . . . . .284 Prescaler Select Encoding . . . . . . . . . . . . . . . . . . . . . . . . . . 286 PIT Interrupt Requests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292 15-1 15-2 15-3 15-4 15-5 15-6 15-7 15-8 Signal Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298 Timer Modules Memory Map . . . . . . . . . . . . . . . . . . . . . . . . 299 Output Compare Action Selection . . . . . . . . . . . . . . . . . . . . 307 Input Capture Edge Selection. . . . . . . . . . . . . . . . . . . . . . . . 308 Prescaler Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311 Clock Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316 TIMPORT I/O Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325 Timer Interrupt Requests . . . . . . . . . . . . . . . . . . . . . . . . . . . 326 16-1 16-2 16-4 16-5 16-6 16-7 16-8 16-9 16-10 Signal Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334 Serial Communications Interface Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335 SCI Normal, Loop, and Single-Wire Mode Pin Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338 Example Baud Rates (System Clock = 33 MHz) . . . . . . . . .350 Example 10-Bit and 11-Bit Frames. . . . . . . . . . . . . . . . . . . . 352 Start Bit Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 358 Data Bit Recovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .358 Stop Bit Recovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .359 SCI Port Control Summary . . . . . . . . . . . . . . . . . . . . . . . . . . 368 SCI Interrupt Request Sources. . . . . . . . . . . . . . . . . . . . . . .369 17-1 17-2 17-3 17-4 17-5 17-6 17-7 17-8 Signal Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374 SPI Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375 SS Pin I/O Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . 377 Bidirectional Pin Configurations . . . . . . . . . . . . . . . . . . . . . . 378 SPI Baud Rate Selection (33-MHz Module Clock) . . . . . . . . 380 SPI Port Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .384 Normal Mode and Bidirectional Mode . . . . . . . . . . . . . . . . . 394 SPI Interrupt Request Sources. . . . . . . . . . . . . . . . . . . . . . .397 16-3 MMC2107 - Rev. 2.0 MOTOROLA Page Technical Data List of Tables For More Information On This Product, Go to: www.freescale.com 39 Freescale Semiconductor, Inc. List of Tables Table Freescale Semiconductor, Inc... 18-1 18-2 18-3 18-4 18-5 18-6 18-7 18-8 18-9 18-10 Title 18-17 18-18 Multiplexed Analog Input Channels . . . . . . . . . . . . . . . . . . . 409 QADC Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 410 Prescaler Clock High Times . . . . . . . . . . . . . . . . . . . . . . . . . 417 Prescaler Clock Low Times . . . . . . . . . . . . . . . . . . . . . . . . . 418 Queue 1 Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . 420 Queue 2 Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . 423 Pause Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429 Queue Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433 Input Sample Times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 439 Non-Multiplexed Channel Assignments and Pin Designations. . . . . . . . . . . . . . . . . . . . . . . . . . . .440 Multiplexed Channel Assignments and Pin Designations. . . . . . . . . . . . . . . . . . . . . . . . . . . .440 Analog Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444 Trigger Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454 Status Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454 QADC Clock Programmability . . . . . . . . . . . . . . . . . . . . . . .479 External Circuit Settling Time to 1/2 LSB (10-Bit Conversions) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 499 Error Resulting From Input Leakage (IOff) . . . . . . . . . . . . . . 500 QADC Status Flags and Interrupt Sources. . . . . . . . . . . . . .500 19-1 19-2 19-3 19-4 Signal Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 505 Data Transfer Cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 509 EB[3:0] Assertion Encoding . . . . . . . . . . . . . . . . . . . . . . . . . 510 Emulation Mode Chip-Select Summary . . . . . . . . . . . . . . . . 517 20-1 20-2 20-3 20-4 Signal Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 524 Chip Select Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . 524 Chip Select Wait States Encoding . . . . . . . . . . . . . . . . . . . . 529 Chip Select Address Range Encoding . . . . . . . . . . . . . . . . . 531 21-1 21-2 21-3 21-4 JTAG Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .542 List of Pins Not Scanned in JTAG Mode . . . . . . . . . . . . . . . 548 Boundary-Scan Register Definition . . . . . . . . . . . . . . . . . . . 549 OnCE Register Addressing . . . . . . . . . . . . . . . . . . . . . . . . . 563 18-11 18-12 18-13 18-14 18-15 18-16 Technical Data 40 Page MMC2107 - Rev. 2.0 List of Tables For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. List of Tables Freescale Semiconductor, Inc... Table Title 21-5 21-6 21-7 Sequential Control Field Settings . . . . . . . . . . . . . . . . . . . . . 565 Memory Breakpoint Control Field Settings . . . . . . . . . . . . . .567 Processor Mode Field Settings. . . . . . . . . . . . . . . . . . . . . . .569 22-1 22-2 22-3 22-4 22-5 22-6 22-7 22-8 22-9 22-10 22-11 22-12 22-13 22-14 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . 586 Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 587 ESD Protection Characteristics . . . . . . . . . . . . . . . . . . . . . . 587 DC Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 588 PLL Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . 590 QADC Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . 591 QADC Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . 592 QADC Conversion Specifications. . . . . . . . . . . . . . . . . . . . . 593 FLASH Program and Erase Characteristics . . . . . . . . . . . . . 594 FLASH EEPROM Module Life Characteristics . . . . . . . . . . . 594 External Interface Timing Characteristics. . . . . . . . . . . . . . . 596 Reset and Configuration Override Timing . . . . . . . . . . . . . . 601 SPI Timing Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 602 OnCE, JTAG, and Boundary Scan Timing . . . . . . . . . . . . . .605 24-1 MC Order Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 615 MMC2107 - Rev. 2.0 MOTOROLA Page Technical Data List of Tables For More Information On This Product, Go to: www.freescale.com 41 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... List of Tables Technical Data 42 MMC2107 - Rev. 2.0 List of Tables For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 1. General Description Freescale Semiconductor, Inc... 1.1 Contents 1.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 1.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 1.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 1.2 Introduction The MMC2107 is the first member of a family of general-purpose microcontrollers (MCU) based on the M*CORETM M210 central processor unit (CPU). As a low-voltage part, the MMC2107 operates at voltages between 2.7 volts and 3.6 volts. It is particularly suited for use in battery-powered applications. The operating frequency is up to a maximum of 33 MHz over a temperature range of -40C to 85C. Available packages are 100-pin low-profile quad flat pack (LQFP) or a 144-pin LQFP for applications requiring the full external memory interface support or a large number of general-purpose inputs/outputs (GPIO). TMM*CORE is a trademark of Motorola, Inc. MMC2107 - Rev. 2.0 MOTOROLA Technical Data General Description For More Information On This Product, Go to: www.freescale.com 43 Freescale Semiconductor, Inc. General Description 1.3 Features Freescale Semiconductor, Inc... Features of the MMC2107 include: * M*CORE M210 integer processor: - 32-bit reduced instruction set computer (RISC) architecture - Low power and high performance * OnCETM debug support * On-chip 128-Kbyte FLASH: - Motorola's one transistor, CDR MoneT(1) FLASH bit cell - Page mode (2111) read access - External VPP required for programming - 16-K block size * On-chip, 8-Kbyte static random-access memory (SRAM): - One clock per access (including bytes, half-words, and words) - Byte, half-word (16 bits), and word (32 bits) read/write accesses - Standby power supply support * Serial peripheral interface (SPI): - Master mode and slave mode - Wired-OR mode - Slave select output - Mode fault error flag with CPU interrupt capability - Double-buffered operation - Serial clock with programmable polarity and phase - Control of SPI operation during wait mode - Reduced drive control TMOnCE is a trademark of Motorola, Inc. 1. CDR MoneT designates the Motorola one-transistor bitcell. Technical Data 44 MMC2107 - Rev. 2.0 General Description For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... General Description Features * Two serial communications interfaces (SCI): - Full-duplex operation - Standard mark/space non-return-to-zero (NRZ) format - 13-bit baud rate selection - Programmable 8-bit or 9-bit data format - Separately enabled transmitter and receiver - Separate receiver and transmitter CPU interrupt requests - Programmable transmitter output polarity - Two receiver wakeup methods (idle line and address mark) - Interrupt-driven operation with eight flags - Receiver framing error detection - Hardware parity checking - 1/16 bit-time noise detection - General-purpose input/output port * Two timers: - Four 16-bit input capture/output compare channels - 16-bit architecture - 16-bit pulse accumulator - Pulse widths variable from microseconds to seconds - Prescaler - Toggle-on-overflow feature for pulse-width modulator (PWM) generation - Timer port pullups enabled on reset * Queued analog-to-digital converter (QADC): - Eight analog input channels - 10-bit resolution 2 counts accuracy - Minimum 7 s conversion time - Internal sample and hold - Programmable input sample time for various source impedances - Two conversion command queues with a total of 64 entries - Subqueues possible using pause mechanism - Queue complete and pause software interrupts available on both queues MMC2107 - Rev. 2.0 MOTOROLA Technical Data General Description For More Information On This Product, Go to: www.freescale.com 45 Freescale Semiconductor, Inc. General Description - Queue pointers indicate current location for each queue - Automated queue modes initiated by: External edge trigger and gated trigger Periodic/interval timer, within queued analog-to-digital converter (QADC) module {queue1 and queue2} Software command Freescale Semiconductor, Inc... - Single-scan or continuous-scan of queues - Output data readable in three formats: Right-justified unsigned Left-justified signed Left-justified unsigned - Unused analog channels can be used as digital input/output (I/O) - Minimum pin set configuration implemented * Interrupt controller: - Up to 40 interrupt sources - 32 unique programmable priority levels for each interrupt source - Independent enable/disable of pending interrupts based on priority level - Select normal or fast interrupt request for each priority level - Fast interrupt requests always have priority over normal interrupts. - Ability to mask interrupts at and below a defined priority level - Ability to select between autovectored or vectored interrupt requests - Vectored interrupts generated based on priority level - Ability to generate a separate vector number for normal and fast interrupts - Ability for software to self-schedule interrupts - Software visibility of pending interrupts and interrupt signals to core - Asynchronous operation to support wakeup from low-power modes Technical Data 46 MMC2107 - Rev. 2.0 General Description For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... General Description Features * External interrupts supported: - Rising/falling edge select - Low-level sensitive - Ability for software generation of external interrupt event - General-purpose input/output support * Periodic interval timer: - 16-bit counter - Selectable as free running or count down * Watchdog timer: - 16-bit counter - Low-power mode support * Phase-lock loop (PLL): - Reference crystal from 2 to 10 MHz - Low-power modes supported - Separate clock-out signal * Reset: - Separate reset in and reset out signals - Six sources of reset: Power-on reset (POR) External Software Watchdog Loss of clock Loss of lock - Status flag indication of source of last reset * Chip configurations: - Support for single-chip, master, emulation, and test modes - System configuration during reset - Bus monitor - Configurable output pad drive strength control MMC2107 - Rev. 2.0 MOTOROLA Technical Data General Description For More Information On This Product, Go to: www.freescale.com 47 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... General Description * General-purpose input/output (GPIO): - Up to 72 bits of GPIO - Coherent 32-bit control - Bit manipulation supported via set/clear functions - Unused peripheral pins may be used as extra GPIO. - Reduced drive control * M*CORE to IPbus interface: - Complete interfacing between the M*CORE bus and the IPbus peripheral bus - Minimum of three clocks for peripheral bus access - Data alignment and data width conversion between the M*CORE 32-bit data bus and the IPbus peripheral data buses * External interface: - Provides for direct support of asynchronous random-access memory (RAM), read-only memory (ROM), and FLASH - Support interfacing to 16-bit and 32-bit data buses - 32-bit external bidirectional data bus - 23-bit address bus - Four chip selects - Byte/write enables - Ability to boot from internal or external memories - Internal bus activity is visible via show-cycle mode - Special chip selects support replacement of GPIO with external logic (port replacement logic) - Emulation of internal page mode FLASH support * Joint Test Action Group (JTAG) support for system-level board testing 1.4 Block Diagram The basic structure of the MMC2107 is shown in Figure 1-1. Technical Data 48 MMC2107 - Rev. 2.0 General Description For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. TRST TCLK TMS TDI TDO DE VSTBY General Description Block Diagram VSS x 8 VDD x 8 JTAG TAP SRAM 8-KBYTE FLASH 128-KBYTE VPP VDDF, VSSF TEST IPBUS INTERFACE PROGRAMMABLE INTERVAL TIMER 1 INTERRUPT CONTROLLER PROGRAMMABLE INTERVAL TIMER 2 EDGE PORT WATCHDOG TIMER INT[7:0] A[22:0] PORTS M*CORE BUS CS M*CORE (M210) EXTERNAL MEMORY INTERFACE OnCE PSTAT[3:0] R/W EB[3:0] CS[3:0] TC[2:0] SHS CSE[1:0] TA TEA OE TEST EXTAL XTAL CLKOUT VDDSYN VSSSYN OSC/PLL POR RESET RSTOUT RESET IPBUS VRL, VRH TIM1 TIM2 SCI1 SPI SCI2 ADC VDDA, VSSA PQA[4:3] PQA[1:0] PQB[3:0] MISO MOSI SCK SS TXD2 RXD2 RXD1 TXD1 ICOC2[3:0] VDDH ICOC1[3:0] Freescale Semiconductor, Inc... D[31:0] Figure 1-1. Block Diagram MMC2107 - Rev. 2.0 MOTOROLA Technical Data General Description For More Information On This Product, Go to: www.freescale.com 49 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... General Description Technical Data 50 MMC2107 - Rev. 2.0 General Description For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 2. System Memory Map Freescale Semiconductor, Inc... 2.1 Contents 2.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 2.3 Address Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 2.4 Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 2.2 Introduction The address map, shown in Figure 2-1, includes: * 128 Kbytes of internal FLASH * 8 Kbytes of internal static random-access memory (SRAM) * Internal memory mapped registers * External address space MMC2107 - Rev. 2.0 MOTOROLA Technical Data System Memory Map For More Information On This Product, Go to: www.freescale.com 51 Freescale Semiconductor, Inc. System Memory Map 2.3 Address Map Freescale Semiconductor, Inc... EXTERNAL MEMORY 0x8000_0000 REGISTERS SEE 2.4 Register Map 0x00c0_0000 0x0080_0000 0 INTERNAL SRAM 8 KBYTES INTERNAL FLASH 128 KBYTES Figure 2-1. Address Map Technical Data 52 MMC2107 - Rev. 2.0 System Memory Map For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. System Memory Map Address Map Freescale Semiconductor, Inc... Table 2-1. Register Address Location Map(1) Base Address (Hex) Usage 0x00c0_0000 Ports(2) (PORTS) 0x00c1_0000 Chip configuration (CCM) 0x00c2_0000 Chip selects (CS) 0x00c3_0000 Clocks (CLOCK) 0x00c4_0000 Reset (RESET) 0x00c5_0000 Interrupt controller (INTC) 0x00c6_0000 Edge port (EPORT) 0x00c7_0000 Watchdog timer (WDT) 0x00c8_0000 Programmable interrupt timer 1 (PIT1) 0x00c9_0000 Programmable interrupt timer 2 (PIT2) 0x00ca_0000 Queued analog-to-digital converter (QADC) 0x00cb_0000 Serial peripheral interface (SPI) 0x00cc_0000 Serial communications interface 1 (SCI1) 0x00cd_0000 Serial communications interface 2 (SCI2) 0x00ce_0000 Timer 1 (TIM1) 0x00cf_0000 Timer 2 (TIM2) 0x00d0_0000 FLASH registers (CMFR) 1. See module sections for details of how much of each block is being decoded. Accesses to addresses outside the module memory maps (and also the reserved area 0x00d1_0000-0x7fff_ffff) will not be responded to and will result in a bus monitor transfer error exception. 2. The port register space is mirrored/repeated in the 64-Kbyte block. This allows the full 64-Kbyte block to be decoded and used to execute an external access to a port replacement unit in emulation mode. MMC2107 - Rev. 2.0 MOTOROLA Technical Data System Memory Map For More Information On This Product, Go to: www.freescale.com 53 Freescale Semiconductor, Inc. System Memory Map 2.4 Register Map Address Register Name Bit Number Ports (PORTS) Freescale Semiconductor, Inc... 0x00c0_0000 0x00c0_0001 0x00c0_0002 0x00c0_0003 0x00c0_0004 0x00c0_0005 0x00c0_0006 P = Current pin state Port A Output Data Register (PORTA) See page 251. Port B Output Data Register (PORTB) See page 251. Port C Output Data Register (PORTC) See page 251. Port D Output Data Register (PORTD) See page 251. Port E Output Data Register (PORTE) See page 251. Port F Output Data Register (PORTF) See page 251. Port G Output Data Register (PORTG) See page 251. U = Unaffected Bit 7 6 5 4 3 2 1 Bit 0 PORTA7 PORTA6 PORTA5 PORTA4 PORTA3 PORTA2 PORTA1 PORTA0 1 1 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 PORTB7 PORTB6 PORTB5 PORTB4 PORTB3 PORTB2 PORTB1 PORTB0 1 1 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 PORTC7 PORTC6 PORTC5 PORTC4 PORTC3 PORTC2 PORTC1 PORTC0 1 1 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 PORTD7 PORTD6 PORTD5 PORTD4 PORTD3 PORTD2 PORTD1 PORTD0 1 1 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 PORTE7 PORTE6 PORTE5 PORTE4 PORTE3 PORTE2 PORTE1 PORTE0 1 1 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 PORTF7 PORTF6 PORTF5 PORTF4 PORTF3 PORTF2 PORTF1 PORTF0 1 1 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 PORTG7 PORTG6 PORTG5 PORTG4 PORTG3 PORTG2 PORTG1 PORTG0 1 1 1 1 1 1 1 1 Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset : Read: Write: Reset: Read: Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 1 of 34) Technical Data 54 MMC2107 - Rev. 2.0 System Memory Map For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. System Memory Map Register Map Address 0x00c0_0007 Freescale Semiconductor, Inc... 0x00c0_0008 Register Name Port H Output Data Register (PORTH) See page 251. Port I Output Data Register (PORTI) See page 251. 0x00c0_0009 0x00c0_000b 0x00c0_000c 0x00c0_000d 0x00c0_000e 0x00c0_000f 0x00c0_0010 P = Current pin state Bit Number Bit 7 6 5 4 3 2 1 Bit 0 PORTH7 PORTH6 PORTH5 PORTH4 PORTH3 PORTH2 PORTH1 PORTH0 1 1 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 PORTI7 PORTI6 PORTI5 PORTI4 PORTI3 PORTI2 PORTI1 PORTI0 1 1 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 Read: Write: Reset: Read: Write: Reset: Writes have no effect, reads return 0s, and the access terminates without a transfer error exception. Reserved Port A Data Direction Register (DDRA) See page 252. Port B Data Direction Register (DDRB) See page 252. Port C Data Direction Register (DDRC) See page 252. Port D Data Direction Register (DDRD) See page 252. Port E Data Direction Register (DDRE) See page 252. U = Unaffected Bit 7 6 5 4 3 2 1 Bit 0 DDRA7 DDRA6 DDRA5 DDRA4 DDRA3 DDRA2 DDRA1 DDRA0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 DDRB7 DDRB6 DDRB5 DDRB4 DDRB3 DDRB2 DDRB1 DDRB0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 DDRC7 DDRC6 DDRC5 DDRC4 DDRC3 DDRC2 DDRC1 DDRC0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 DDRD7 DDRD6 DDRD5 DDRD4 DDRD3 DDRD2 DDRD1 DDRD0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 DDRE7 DDRE6 DDRE5 DDRE4 DDRE3 DDRE2 DDRE1 DDRE0 0 0 0 0 0 0 0 0 Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 2 of 34) MMC2107 - Rev. 2.0 MOTOROLA Technical Data System Memory Map For More Information On This Product, Go to: www.freescale.com 55 Freescale Semiconductor, Inc. System Memory Map Address 0x00c0_0011 Freescale Semiconductor, Inc... 0x00c0_0012 0x00c0_0013 0x00c0_0014 0x00c0_0015 0x00c0_0017 Register Name Port F Data Direction Register (DDRF) See page 252. Port G Data Direction Register (DDRG) See page 252. Port H Data Direction Register (DDRH) See page 252. Port I Data Direction Register (DDRI) See page 252. Bit Number Bit 7 6 5 4 3 2 1 Bit 0 DDRF7 DDRF6 DDRF5 DDRF4 DDRF3 DDRF2 DDRF1 DDRF0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 DDRG7 DDRG6 DDRG5 DDRG4 DDRG3 DDRG2 DDRG1 DDRG0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 DDRH7 DDRH6 DDRH5 DDRH4 DDRH3 DDRH2 DDRH1 DDRH0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 DDRI7 DDRI6 DDRI5 DDRI4 DDRI3 DDRI2 DDRI1 DDRI0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: Writes have no effect, reads return 0s, and the access terminates without a transfer error exception. Reserved Bit 7 0x00c0_0018 P = Current pin state 4 3 2 1 Bit 0 6 5 4 3 2 1 Bit 0 Port B Pin Data/Set Read: PORTBP7 PORTBP6 PORTBP5 PORTBP4 PORTBP3 PORTBP2 PORTBP1 PORTBP0 Data Register Write: SETB7 SETB6 SETB5 SETB4 SETB3 SETB2 SETB1 SETB0 (PORTBP/SETB) See page 253. Reset: P P P P P P P P Bit 7 0x00c0_001a 5 Port A Pin Data/Set Read: PORTAP7 PORTAP6 PORTAP5 PORTAP4 PORTAP3 PORTAP2 PORTAP1 PORTAP0 Data Register Write: SETA7 SETA6 SETA5 SETA4 SETA3 SETA2 SETA1 SETA0 (PORTAP/SETA) See page 253. Reset: P P P P P P P P Bit 7 0x00c0_0019 6 6 5 4 3 2 1 Bit 0 Port C Pin Data/Set Read: PORTCP7 PORTCP6 PORTCP5 PORTCP4 PORTCP3 PORTCP2 PORTCP1 PORTCP0 Data Register Write: SETC7 SETC6 SETC5 SETC4 SETC3 SETC2 SETC1 SETC0 (PORTCP/SETC) See page 253. Reset: P P P P P P P P U = Unaffected = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 3 of 34) Technical Data 56 MMC2107 - Rev. 2.0 System Memory Map For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. System Memory Map Register Map Address Register Name Bit Number Bit 7 0x00c0_001b Freescale Semiconductor, Inc... Port I Pin Data/Set Read: PORTIP7 Data Register Write: SETI7 (PORTIP/SETI) See page 253. Reset: P Bit 7 0x00c0_0021 0x00c0_0023 0x00c0_0024 P = Current pin state 1 Bit 0 6 5 4 3 2 1 Bit 0 6 5 4 3 2 1 Bit 0 6 5 4 3 2 1 Bit 0 6 5 4 3 2 1 Bit 0 Port H Pin Data/Set Read: PORTHP7 PORTHP6 PORTHP5 PORTHP4 PORTHP3 PORTHP2 PORTHP1 PORTHP0 Data Register Write: SETH7 SETH6 SETH5 SETH4 SETH3 SETH2 SETH1 SETH0 (PORTHP/SETH) See page 253. Reset: P P P P P P P P Bit 7 0x00c0_0020 2 Port G Pin Data/Set Read: PORTGP7 PORTGP6 PORTGP5 PORTGP4 PORTGP3 PORTGP2 PORTGP1 PORTGP0 Data Register Write: SETG7 SETG6 SETG5 SETG4 SETG3 SETG2 SETG1 SETG0 (PORTGP/SETG) See page 253. Reset: P P P P P P P P Bit 7 0x00c0_001f 3 Port F Pin Data/Set Read: PORTFP7 PORTFP6 PORTFP5 PORTFP4 PORTFP3 PORTFP2 PORTFP1 PORTFP0 Data Register Write: SETF7 SETF6 SETF5 SETF4 SETF3 SETF2 SETF1 SETF0 (PORTFP/SETF) See page 253. Reset: P P P P P P P P Bit 7 0x00c0_001e 4 Port E Pin Data/Set Read: PORTEP7 PORTEP6 PORTEP5 PORTEP4 PORTEP3 PORTEP2 PORTEP1 PORTEP0 Data Register Write: SETE7 SETE6 SETE5 SETE4 SETE3 SETE2 SETE1 SETE0 (PORTEP/SETE) See page 253. Reset: P P P P P P P P Bit 7 0x00c0_001d 5 Port D Pin Data/Set Read: PORTDP7 PORTDP6 PORTDP5 PORTDP4 PORTDP3 PORTDP2 PORTDP1 PORTDP0 Data Register Write: SETD7 SETD6 SETD5 SETD4 SETD3 SETD2 SETD1 SETD0 (PORTDP/SETD) See page 253. Reset: P P P P P P P P Bit 7 0x00c0_001c 6 U = Unaffected 5 4 3 2 1 Bit 0 PORTIP6 PORTIP5 PORTIP4 PORTIP3 PORTIP2 PORTIP1 PORTIP0 SETI6 SETI5 SETI4 SETI3 SETI2 SETI1 SETI0 P P P P P P P 6 5 4 3 2 1 Bit 0 Writes have no effect, reads return 0s, and the access terminates without a transfer error exception. Reserved Port A Clear Output Data Register (CLRA) See page 254. 6 Bit 7 6 5 4 3 2 1 Bit 0 Read: 0 0 0 0 0 0 0 0 Write: CLRA7 CLRA6 CLRA5 CLRA4 CLRA3 CLRA2 CLRA1 CLRA0 Reset: 0 0 0 0 0 0 0 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 4 of 34) MMC2107 - Rev. 2.0 MOTOROLA Technical Data System Memory Map For More Information On This Product, Go to: www.freescale.com 57 Freescale Semiconductor, Inc. System Memory Map Address 0x00c0_0025 Freescale Semiconductor, Inc... 0x00c0_0026 0x00c0_0027 0x00c0_0028 0x00c0_0029 0x00c0_002a 0x00c0_002b P = Current pin state Register Name Port B Clear Output Data Register (CLRB) See page 254. Port C Clear Output Data Register (CLRC) See page 254. Port D Clear Output Data Register (CLRD) See page 254. Port E Clear Output Data Register (CLRE) See page 254. Port F Clear Output Data Register (CLRF) See page 254. Port G Clear Output Data Register (CLRG) See page 254. Port H Clear Output Data Register (CLRH) See page 254. U = Unaffected Bit Number Bit 7 6 5 4 3 2 1 Bit 0 Read: 0 0 0 0 0 0 0 0 Write: CLRB7 CLRB6 CLRB5 CLRB4 CLRB3 CLRB2 CLRB1 CLRB0 Reset: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Read: 0 0 0 0 0 0 0 0 Write: CLRC7 CLRC6 CLRC5 CLRC4 CLRC3 CLRC2 CLRC1 CLRC0 Reset: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Read: 0 0 0 0 0 0 0 0 Write: CLRD7 CLRD6 CLRD5 CLRD4 CLRD3 CLRD2 CLRD1 CLRD0 Reset: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Read: 0 0 0 0 0 0 0 0 Write: CLRE7 CLRE6 CLRE5 CLRE4 CLRE3 CLRE2 CLRE1 CLRE0 Reset: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Read: 0 0 0 0 0 0 0 0 Write: CLRF7 CLRF6 CLRF5 CLRF4 CLRF3 CLRF2 CLRF1 CLRF0 Reset: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Read: 0 0 0 0 0 0 0 0 Write: CLRG7 CLRG6 CLRG5 CLRG4 CLRG3 CLRG2 CLRG1 CLRG0 Reset: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Read: 0 0 0 0 0 0 0 0 Write: CLRH7 CLRH6 CLRH5 CLRH4 CLRH3 CLRH2 CLRH1 CLRH0 Reset: 0 0 0 0 0 0 0 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 5 of 34) Technical Data 58 MMC2107 - Rev. 2.0 System Memory Map For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. System Memory Map Register Map Address 0x00c0_002c Register Name Port I Clear Output Data Register (CLRI) See page 254. Freescale Semiconductor, Inc... 0x00c0_002d 0x00c0_002f Bit Number Bit 7 6 5 4 3 2 1 Bit 0 Read: 0 0 0 0 0 0 0 0 Write: CLRI7 CLRI6 CLRI5 CLRI4 CLRI3 CLRI2 CLRI1 CLRI0 Reset: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Writes have no effect, reads return 0s, and the access terminates without a transfer error exception. Reserved Bit 7 0x00c0_0030 Port C/D Pin Read: PCDPA Assignment Register Write: (PCDPAR) See page 255. Reset: See note 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Note: Reset state determined during reset configuration. PCDPA = 1 except in single-chip mode or when an external boot device is selected with a 16-bit port size in master mode. Bit 7 0x00c0_0031 5 4 3 2 1 Bit 0 Port E Pin Read: PEPA7 PEPA6 PEPA5 PEPA4 PEPA3 PEPA2 PEPA1 PEPA0 Assignment Register Write: (PEPAR) See page 256. Reset: Reset state determined during reset configuration as shown in Table 11-2. PEPAR Reset Values. Bit 7 0x00c0_0032 0x00c0_003f 0x00c0_0040 0x00c0_ffff Reserved U = Unaffected 6 5 4 3 2 1 Bit 0 Writes have no effect, reads return 0s, and the access terminates without a transfer error exception. Reserved Bit 7 P = Current pin state 6 6 5 4 3 2 1 Bit 0 Ports register space (block of 0x00c0_0000 through 0x00c0_oo3f) is mirrored/repeated. = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 6 of 34) MMC2107 - Rev. 2.0 MOTOROLA Technical Data System Memory Map For More Information On This Product, Go to: www.freescale.com 59 Freescale Semiconductor, Inc. System Memory Map Address Register Name Bit Number Chip Configuration Module (CCM) Bit 15 0x00c1_0000 0x00c1_0001 Chip Configuration Read: Register Write: (CCR) See page 94. Reset: Read: 14 13 12 SHEN EMINT 0 LOAD 11 10 9 Bit 8 0 MODE2 MODE1 MODE0 Note 1 0 Note 2 Note 2 0 Note 1 Note 1 Note 1 Bit 7 6 5 4 3 2 1 Bit 0 SZEN PSTEN SHINT BME BMD BMT1 BMT0 Note 3 Note 2 0 1 0 0 0 0 Freescale Semiconductor, Inc... Write: Reset: 0 Notes: 1. Determined during reset configuration 2. 0 for all configurations except emulation mode, 1 for emulation mode 3. 0 for all configurations except emulation and master modes, 1 for emulation and master modes Bit 7 0x00c1_0002 0x00c1_0004 0x00c1_0005 4 3 2 1 Bit 0 6 5 4 3 2 1 Bit 0 Writes have no effect, reads return 0s, and the access terminates without a transfer error exception. Reserved Reset Configuration Register (RCON) See page 97. 5 Writes have no effect, reads return 0s, and the access terminates without a transfer error exception. Reserved Bit 7 0x00c1_0003 6 Read: Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 RLOAD 0 0 0 MODE 0 0 0 0 Write: Reset: Read: 1 1 RPLLSEL RPLLREF 1 0 BOOTPS BOOTSEL Write: Reset: P = Current pin state U = Unaffected 1 1 1 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 7 of 34) Technical Data 60 MMC2107 - Rev. 2.0 System Memory Map For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. System Memory Map Register Map Address 0x00c1_0006 0x00c1_0007 Register Name Chip Identification Register (CIR) See page 99. Bit Number Read: 14 13 12 11 10 9 Bit 8 0 PIN7 0 PIN6 0 PIN5 1 PIN4 0 PIN3 1 PIN2 1 PIN1 1 PIN0 0 0 0 1 0 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 0 PRN7 0 PRN6 0 PRN5 0 PRN4 0 PRN3 0 PRN2 0 PRN1 0 PRN0 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Write: Reset: Read: Freescale Semiconductor, Inc... Bit 15 Write: Reset: 0x00c1_0008 0x00c1_0009 Chip Test Register (CTR) See page 100. Read: Write: Reset: Read: Write: Reset: 0x00c1_000a 0x00c1_000b Writes have no effect, reads return 0s, and the access terminates without a transfer error exception. Reserved Bit 7 0x00c1_000c 0x00c1_000f Unimplemented P = Current pin state Unimplemented U = Unaffected 5 4 3 2 1 Bit 0 Access results in the module generating an access termination transfer error. Bit 7 0x00c1_0010 0x00c1_ffff 6 6 5 4 3 2 1 Bit 0 Access results in a bus monitor timeout generating an access termination transfer error. = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 8 of 34) MMC2107 - Rev. 2.0 MOTOROLA Technical Data System Memory Map For More Information On This Product, Go to: www.freescale.com 61 Freescale Semiconductor, Inc. System Memory Map Address Register Name Bit Number Chip Selects (CS) 0x00c2_0000 0x00c2_0001 Chip Select Control Register 0 (CSCR0) See page 525. Bit 15 14 13 12 11 10 9 Bit 8 SO RO PS WWS WE WS2 WS1 WS0 0 0 See note 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 TAEN CSEN 0 1 See note Read: Write: Reset: Read: Freescale Semiconductor, Inc... Write: Reset: 0 0 0 0 0 Note: Reset state determined during reset configuration. 0x00c2_0002 0x00c2_0003 Chip Select Control Register 1 (CSCR1) See page 526. Bit 15 14 13 12 11 10 9 Bit 8 SO RO PS WWS WE WS2 WS1 WS0 0 0 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 TAEN CSEN 0 1 See note Read: Write: Reset: Read: Write: Reset: 0 0 0 0 0 Note: Reset state determined during reset configuration 0x00c2_0004 0x00c2_0005 Chip Select Control Register 2 (CSCR2) See page 526. Bit 15 14 13 12 11 10 9 Bit 8 SO RO PS WWS WE WS2 WS1 WS0 0 0 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 TAEN CSEN 1 0 Read: Write: Reset: Read: Write: Reset: P = Current pin state U = Unaffected 0 0 0 0 0 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 9 of 34) Technical Data 62 MMC2107 - Rev. 2.0 System Memory Map For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. System Memory Map Register Map Address 0x00c2_0006 0x00c2_0007 Register Name Chip Select Control Register 3 (CSCR3) See page 527. Bit Number Bit 15 14 13 12 11 10 9 Bit 8 SO RO PS WWS WE WS2 WS1 WS0 0 0 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 TAEN CSEN Read: Write: Reset: Read: Write: Freescale Semiconductor, Inc... Reset: 0x00c2_0008 0x00c2_ffff Unimplemented 0 0 0 0 0 0 1 0 Bit 7 6 5 4 3 2 1 Bit 0 Access results in a bus monitor timeout generating an access termination transfer error. Clocks (CLOCK) 0x00c3_0000 0x00c3_0001 Synthesizer Control Register (SYNCR) See page 227. Bit 15 14 13 12 11 10 9 Bit 8 LOLRE MFD2 MFD1 MFD0 LOCRE RFD2 RFD1 RFD0 0 0 1 0 0 0 0 1 Bit 7 6 5 4 3 2 1 Bit 0 LOCEN DISCLK FWKUP RSVD4 STMPD1 STMPD0 RSVD1 RSVD0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 PLLSEL PLLREF LOCKS LOCK LOCS 0 0 Note 1 Note 1 Note 2 Note 2 0 0 0 Read: Write: Reset: Read: Write: Reset: 0x00c3_0002 Synthesizer Status Register (SYNSR) See page 230. Read: PLLMODE Write: Reset: Note 1 Notes: 1. Reset state determined during reset configuration 2. See the LOCKS and LOCK bit descriptions. P = Current pin state U = Unaffected = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 10 of 34) MMC2107 - Rev. 2.0 MOTOROLA Technical Data System Memory Map For More Information On This Product, Go to: www.freescale.com 63 Freescale Semiconductor, Inc. System Memory Map Address 0x00c3_0003 Register Name Synthesizer Test Register (SYNTR) See page 233. Bit Number Read: Freescale Semiconductor, Inc... Synthesizer Test Register 2 (SYNTR2) See page 234. 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 31 30 29 28 27 26 25 Bit 24 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 23 22 21 20 19 18 17 Bit 16 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 RSVD9 RSVD8 Write: Reset: 0x00c3_0004 0x00c3_0005 0x00c3_0006 0x00c3_0007 Bit 7 Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 RSVD7 RSVD6 RSVD5 RSVD4 RSVD3 RSVD2 RSVD2 RSVD0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Read: Write: Reset: 0x00c3_0008 0x00c3_ffff Unimplemented Access results in a bus monitor timeout generating an access termination transfer error. Reset (RESET) 0x00c4_0000 P = Current pin state Reset Control Register (RCR) See page 133. U = Unaffected Bit 7 6 5 4 3 2 1 Bit 0 FRCRSTOUT 0 0 0 0 0 0 SOFTRST 0 0 0 0 0 0 0 0 Read: Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 11 of 34) Technical Data 64 MMC2107 - Rev. 2.0 System Memory Map For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. System Memory Map Register Map Address Register Name Reset Status Register (RSR) See page 134. 0x00c4_0001 Reset Test Register (RTR) See page 135. Freescale Semiconductor, Inc... 0x00c4_0002 0x00c4_0003 Bit Number Read: Bit 7 6 5 4 3 2 1 Bit 0 0 0 SOFT WDR POR EXT LOC LOL 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Write: Reset: Read: Write: Reset: Writes have no effect, reads return 0s, and the access terminates without a transfer error exception. Reserved Bit 7 0x00c4_0004 0x00c4_ffff Reset dependent Unimplemented 6 5 4 3 2 1 Bit 0 Access results in a bus monitor timeout generating an access termination transfer error. Interrupt Controller (INTC) 0x00c5_0000 0x00c5_0001 Interrupt Control Register (ICR) See page 157. Bit 15 14 13 12 11 10 9 Bit 8 AE FVE ME MFI 0 0 0 0 1 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 MASK4 MASK3 MASK2 MASK1 MASK0 Read: Write: Reset: Read: Write: Reset: 0x00c5_0002 0x00c5_0003 Interrupt Status Register (ISR) See page 159. Read: 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 INT FINT 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 VEC6 VEC5 VEC4 VEC3 VEC2 VEC1 VEC0 0 0 0 0 0 0 0 0 Write: Reset: Read: Write: Reset: P = Current pin state U = Unaffected = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 12 of 34) MMC2107 - Rev. 2.0 MOTOROLA Technical Data System Memory Map For More Information On This Product, Go to: www.freescale.com 65 Freescale Semiconductor, Inc. System Memory Map Address 0x00c5_0004 0x00c5_0005 0x00c5_0006 0x00c5_0007 Register Name Interrupt Force Register High (IFRH) See page 160. Bit Number Read: Bit 31 30 29 28 27 26 25 Bit 24 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 23 22 21 20 19 18 17 Bit 16 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 IF39 IF38 IF37 IF36 IF35 IF34 IF33 IF32 0 0 0 0 0 0 0 0 Bit 31 30 29 28 27 26 25 Bit 24 IF31 IF30 IF29 IF28 IF27 IF26 IF25 IF24 0 0 0 0 0 0 0 0 Bit 23 22 21 20 19 18 17 Bit 16 IF23 IF22 IF21 IF20 IF19 IF18 IF17 IF16 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 IF15 IF14 IF13 IF12 IF11 IF10 IF9 IF8 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 IF7 IF6 IF5 IF4 IF3 IF2 IF1 IF0 0 0 0 0 0 0 0 0 Write: Reset: Read: Write: Freescale Semiconductor, Inc... Reset: Read: Write: Reset: Read: Write: Reset: 0x00c5_0008 0x00c5_0009 0x00c5_000a 0x00c5_000b Interrupt Force Register Low (IFRL) See page 161. Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: P = Current pin state U = Unaffected = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 13 of 34) Technical Data 66 MMC2107 - Rev. 2.0 System Memory Map For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. System Memory Map Register Map Address Register Name Interrupt Pending Register (IPR) See page 162. 0x00c5_000c 0x00c5_000d 0x00c5_000e 0x00c5_000f Bit Number Read: Bit 31 30 29 28 27 26 25 Bit 24 IP31 IP30 IP29 IP28 IP27 IP26 IP25 IP24 0 0 0 0 0 0 0 0 Bit 23 22 21 20 19 18 17 Bit 16 IP23 IP22 IP21 IP20 IP19 IP18 IP17 IP16 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 IP15 IP14 IP13 IP12 IP11 IP10 IP9 IP8 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 IP7 IP6 IP5 IP4 IP3 IP2 IP1 IP0 0 0 0 0 0 0 0 0 Bit 31 30 29 28 27 26 25 Bit 24 NIE31 NIE30 NIE29 NIE28 NIE27 NIE26 NIE25 NIE24 0 0 0 0 0 0 0 0 Bit 23 22 21 20 19 18 17 Bit 16 NIE23 NIE22 NIE21 NIE20 NIE19 NIE18 NIE17 NIE16 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 NIE15 NIE14 NIE13 NIE12 NIE11 NIE10 NIE9 NIE8 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 NIE7 NIE6 NIE5 NIE4 NIE3 NIE2 NIE1 NIE0 0 0 0 0 0 0 0 0 Write: Reset: Read: Write: Freescale Semiconductor, Inc... Reset: Read: Write: Reset: Read: Write: Reset: 0x00c5_0010 0x00c5_0011 0x00c5_0012 0x00c5_0013 Normal Interrupt Enable Register (NIER) See page 163. Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: P = Current pin state U = Unaffected = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 14 of 34) MMC2107 - Rev. 2.0 MOTOROLA Technical Data System Memory Map For More Information On This Product, Go to: www.freescale.com 67 Freescale Semiconductor, Inc. System Memory Map Address 0x00c5_0014 0x00c5_0015 0x00c5_0016 0x00c5_0017 Register Name Normal Interrupt Pending Register (NIPR) See page 164. Bit Number Read: Bit 31 30 29 28 27 26 25 Bit 24 NIP31 NIP30 NIP29 NIP28 NIP27 NIP26 NIP25 NIP24 0 0 0 0 0 0 0 0 Bit 23 22 21 20 19 18 17 Bit 16 NIP23 NIP22 NIP21 NIP20 NIP19 NIP18 NIP17 NIP16 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 NIP15 NIP14 NIP13 NIP12 NIP11 NIP10 NIP9 NIP8 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 NIP7 NIP6 NIP5 NIP4 NIP3 NIP2 NIP1 NIP0 0 0 0 0 0 0 0 0 Bit 31 30 29 28 27 26 25 Bit 24 FIE31 FIE30 FIE29 FIE28 FIE27 FIE26 FIE25 FIE24 0 0 0 0 0 0 0 0 Bit 23 22 21 20 19 18 17 Bit 16 FIE23 FIE22 FIE21 FIE20 FIE19 FIE18 FIE17 FIE16 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 FIE15 FIE14 FIE13 FIE12 FIE11 FIE10 FIE9 FIE8 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 FIE7 FIE6 FIE5 FIE4 FIE3 FIE2 FIE1 FIE0 0 0 0 0 0 0 0 0 Write: Reset: Read: Write: Freescale Semiconductor, Inc... Reset: Read: Write: Reset: Read: Write: Reset: 0x00c5_0018 0x00c5_0019 0x00c5_001a 0x00c5_001b Fast Interrupt Enable Register (FIER) See page 165. Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: P = Current pin state U = Unaffected = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 15 of 34) Technical Data 68 MMC2107 - Rev. 2.0 System Memory Map For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. System Memory Map Register Map Address 0x00c5_001c 0x00c5_001d 0x00c5_001e 0x00c5_001f Register Name Fast Interrupt Pending Register (FIPR) See page 166. Bit Number Read: Bit 31 30 29 28 27 26 25 Bit 24 FIP31 FIP30 FIP29 FIP28 FIP27 FIP26 FIP25 FIP24 0 0 0 0 0 0 0 0 Bit 23 22 21 20 19 18 17 Bit 16 FIP23 FIP22 FIP21 FIP20 FIP19 FIP18 FIP17 FIP16 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 FIP15 FIP14 FIP13 FIP12 FIP11 FIP10 FIP9 FIP8 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 FIP7 FIP6 FIP5 FIP4 FIP3 FIP2 FIP1 FIP0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 PLS4 PLS3 PLS2 PLS1 PLS0 Write: Reset: Read: Write: Freescale Semiconductor, Inc... Reset: Read: Write: Reset: Read: Write: Reset: 0x00c5_0040 through 0x00c5_0067 0x00c5_0068 0x00c5_007f Priority Level Select Read: Registers Write: (PLSR39--PLSR0) See page 167. Reset: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Unimplemented Access results in the module generating an access termination transfer error. Bit 7 0x00c5_0080 0x00c5_ffff P = Current pin state Unimplemented U = Unaffected 6 5 4 3 2 1 Bit 0 Access results in a bus monitor timeout generating an access termination transfer error. = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 16 of 34) MMC2107 - Rev. 2.0 MOTOROLA Technical Data System Memory Map For More Information On This Product, Go to: www.freescale.com 69 Freescale Semiconductor, Inc. System Memory Map Address Register Name Bit Number Edge Port (EPORT) Bit 15 0x00c6_0000 0x00c6_0001 EPORT Pin Assignment Register (EPPAR) See page 264. 14 13 12 11 10 9 Bit 8 Read: EPPA7 EPPA6 EPPA5 EPPA4 Write: Reset: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Read: EPPA3 EPPA2 EPPA1 EPPA0 Freescale Semiconductor, Inc... Write: Reset: EPORT Data Direction Register (EPDDR) See page 266. 0x00c6_0002 0x00c6_0003 EPORT Port Interrupt Enable Register (EPIER) See page 267. EPORT Port Data Register (EPDR) See page 268. 0x00c6_0004 EPORT Port Pin Data Register (EPPDR) See page 268. 0x00c6_0005 0x00c6_0006 EPORT Port Flag Regiser (EPFR) See page 269. 0x00c6_0007 P = Current pin state Reserved U = Unaffected 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 EPDD7 EPDD6 EPDD5 EPDD4 EPDD3 EPDD2 EPDD1 EPDD0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 EPIE7 EPIE6 EPIE5 EPIE4 EPIE3 EPIE2 EPIE1 EPIE0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 EPD7 EPD6 EPD5 EPD4 EPD3 EPD2 EPD1 EPD0 1 1 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 EPPD7 EPPD6 EPPD5 EPPD4 EPPD3 EPPD2 EPPD1 EPPD0 P P P P P P P P Bit 7 6 5 4 3 2 1 Bit 0 EPF7 EPF6 EPF5 EPF4 EPF3 EPF2 EPF1 EPF0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: Writes have no effect, reads return 0s, and the access terminates without a transfer error exception. = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 17 of 34) Technical Data 70 MMC2107 - Rev. 2.0 System Memory Map For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. System Memory Map Register Map Address Register Name Bit Number Bit 7 0x00c6_0008 0x00c6_ffff Unimplemented 6 5 4 3 2 1 Bit 0 Access results in a bus monitor timeout generating an access termination transfer error. Watchdog Timer (WDT) Freescale Semiconductor, Inc... 0x00c7_0000 0x00c7_0001 Watchdog Control Register (WCR) See page 275. Read: Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 WAIT DOZE DBG EN Write: Reset: Read: Write: Reset: 0x00c7_0002 0x00c7_0003 Watchdog Modulus Register (WMR) See page 277. 0 0 0 0 1 1 1 1 Bit 15 14 13 12 11 10 9 Bit 8 WM15 WM14 WM13 WM12 WM11 WM10 WM9 WM8 1 1 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 WM7 WM6 WM5 WM4 WM3 WM2 WM1 WM0 1 1 1 1 1 1 1 1 Bit 15 14 13 12 11 10 9 Bit 8 WC15 WC14 WC13 WC12 WC11 WC10 WC9 WC8 1 1 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 WC7 WC6 WC5 WC4 WC3 WC2 WC1 WC0 1 1 1 1 1 1 1 1 Read: Write: Reset: Read: Write: Reset: 0x00c7_0004 0x00c7_0005 Watchdog Count Register (WCNTR) See page 278. Read: Write: Reset: Read: Write: Reset: P = Current pin state U = Unaffected = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 18 of 34) MMC2107 - Rev. 2.0 MOTOROLA Technical Data System Memory Map For More Information On This Product, Go to: www.freescale.com 71 Freescale Semiconductor, Inc. System Memory Map Address 0x00c7_0006 0x00c7_0007 Register Name Watchdog Service Register (WSR) See page 279. Bit Number Bit 15 14 13 12 11 10 9 Bit 8 WS15 WS14 WS13 WS12 WS11 WS10 WS9 WS8 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 WS7 WS6 WS5 WS4 WS3 WS2 WS1 WS0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Read: Write: Reset: Read: Write: Freescale Semiconductor, Inc... Reset: 0x00c7_0008 0x00c7_ffff Unimplemented Access results in a bus monitor timeout generating an access termination transfer error. Programmable Interrupt Timer 1 (PIT1) and Programming Interrupt Timer 2 (PIT2) Note: Addresses for PIT1 are at 0x00c8_#### and addresses for PIT2 are at 0x00c9_####. 0x00c8_0000 0x00c8_0001 0x00c9_0000 0x00c9_0001 PIT Control and Status Register (PCSR) See page 285. Read: Bit 15 14 13 12 0 0 0 0 11 10 9 Bit 8 PRE3 PRE2 PRE1 PRE0 Write: Reset: Read: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 PDOZE PDBG OVW PIE PIF RLD EN 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 PM15 PM14 PM13 PM12 PM11 PM10 PM9 PM8 1 1 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 PM7 PM6 PM5 PM4 PM3 PM2 PM1 PM0 1 1 1 1 1 1 1 1 0 Write: Reset: 0x00c8_0002 0x00c8_0003 0x00c9_0002 0x00c9_0003 PIT Modulus Register (PMR) See page 288. Read: Write: Reset: Read: Write: Reset: P = Current pin state U = Unaffected = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 19 of 34) Technical Data 72 MMC2107 - Rev. 2.0 System Memory Map For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. System Memory Map Register Map Address 0x00c8_0004 0x00c8_0005 0x00c9_0004 0x00c9_0005 Register Name PIT Count Register (PCNTR) See page 289. Bit Number Read: Bit 15 14 13 12 11 10 9 Bit 8 PC15 PC14 PC13 PC12 PC11 PC10 PC9 PC8 1 1 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 1 1 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 Write: Reset: Read: Write: Freescale Semiconductor, Inc... Reset: 0x00c8_0006 0x00c8_0007 Unimplemented Access results in the module generating an access termination transfer error. Bit 7 0x00ca_0008 0x00ca_ffff Unimplemented 6 5 4 3 2 1 Bit 0 Access results in a bus monitor timeout generating an access termination transfer error. Queued Analog-to-Digital Converter (QADC) 0x00ca_0000 0x00ca_0001 QADC Module Read: Configuration Register Write: (QADCMCR) See page 411. Reset: Bit 15 14 13 12 11 10 9 Bit 8 QSTOP QDBG 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 Read: SUPV Write: Reset: 0x00ca_0002 0x00ca_0003 QADC Test Register (QADCTEST) See page 412. Access results in the module generating an access termination transfer error if not in test mode. Bit 7 6 5 4 3 2 1 Bit 0 Access results in the module generating an access termination transfer error if not in test mode. P = Current pin state U = Unaffected = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 20 of 34) MMC2107 - Rev. 2.0 MOTOROLA Technical Data System Memory Map For More Information On This Product, Go to: www.freescale.com 73 Freescale Semiconductor, Inc. System Memory Map Address Register Name 0x00ca_0004 0x00ca_0005 Bit Number Reserved Writes have no effect, reads return 0s, and the access terminates without a transfer error exception. Bit 7 6 5 4 3 2 1 Bit 0 Writes have no effect, reads return 0s, and the access terminates without a transfer error exception. QADC Port A Data Register (PORTQA) See page 413. Freescale Semiconductor, Inc... 0x00ca_0006 QADC Port B Data Register (PORTQB) See page 413. 0x00ca_0007 Read: 6 5 0 0 0 4 3 PQA4 PQA3 2 1 Bit 0 PQA1 PQA0 0 Write: Reset: Read: 0 0 0 P P 0 P P Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 PQB3 PQB2 PQB1 PQB0 Write: Reset: QADC Port A Data Read: Direction Register Write: (DDRQA) See page 415. Reset: 0x00ca_0008 0x00ca_0009 Bit 7 Read: 0 0 0 0 P P P P Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 DDQA4 DDQA3 DDQA1 DDQA0 0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 Write: Reset: 0x00ca_000a 0x00ca_000b QADC Control Register 0 (QACR0) See page 416. Read: Write: Reset: Read: Write: Reset: P = Current pin state U = Unaffected MUX TRG PSH8 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 PSH7 PSH6 PSH5 PSH4 PSA PSL2 PSL1 PSL0 0 0 1 1 0 1 1 1 = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 21 of 34) Technical Data 74 MMC2107 - Rev. 2.0 System Memory Map For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. System Memory Map Register Map Address 0x00ca_000c 0x00ca_000d Register Name QADC Control Register 1 (QACR1) See page 419. Bit Number Bit 15 14 CIE1 PIE1 Read: Read: 12 11 10 9 Bit 8 MQ112 MQ111 MQ110 MQ19 MQ18 0 Write: Reset: 13 SSE1 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 CIE2 PIE2 MQ212 MQ211 MQ210 MQ29 MQ28 Write: Freescale Semiconductor, Inc... Reset: 0x00ca_000e 0x00ca_000f QADC Control Register 2 (QACR2) See page 422. Read: 0 Write: Reset: SSE2 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 RESUME BQ26 BQ25 BQ24 BQ23 BQ22 BQ21 BQ20 0 1 1 1 1 1 1 1 Bit 15 14 13 12 11 10 9 Bit 8 QS9 QS8 CF1 PF1 CF2 PF2 TOR1 TOR2 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 QS7 QS6 CWP5 CWP4 CWP3 CWP2 CWP1 CWP0 0 0 0 0 0 0 0 0 Read: Write: Reset: 0x00ca_0010 0x00ca_0011 QADC Status Register 0 (QASR0) See page 427. Read: Write: Reset: Read: Write: Reset: P = Current pin state U = Unaffected = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 22 of 34) MMC2107 - Rev. 2.0 MOTOROLA Technical Data System Memory Map For More Information On This Product, Go to: www.freescale.com 75 Freescale Semiconductor, Inc. System Memory Map Address 0x00ca_0012 0x00ca_0013 Register Name QADC Status Register 1 (QASR1) See page 436. Bit Number Read: Bit 15 14 13 12 11 10 9 Bit 8 0 0 CWPQ15 CWPQ14 CWPQ13 CWPQ12 CWPQ11 CWPQ10 0 0 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 0 0 CWPQ25 CWPQ24 CWPQ23 CWPQ22 CWPQ21 CWPQ20 0 0 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 Write: Reset: Read: Write: Freescale Semiconductor, Inc... Reset: 0x00ca_0014 0x00ca_01ff Writes have no effect, reads return 0s, and the access terminates without a transfer error exception. Reserved Conversion Command Read: Word Register Write: (CCW) See page 437. Reset: 0x00ca_0200 0x00ca_027e Read: Write: Reset: 0x00ca_0280 0x00ca_02fe Right-Justified Unsigned Result Register (RJURR) See page 441. Read: Bit 15 14 13 12 11 10 0 0 0 0 0 0 9 Bit 8 P BYP 0 0 0 0 0 0 U U Bit 7 6 5 4 3 2 1 Bit 0 IST1 IST0 CHAN5 CHAN4 CHAN3 CHAN2 CHAN1 CHAN0 U U U U U U U U Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 RESULT Write: Reset: Read: Write: 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 RESULT Reset: P = Current pin state U = Unaffected = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 23 of 34) Technical Data 76 MMC2107 - Rev. 2.0 System Memory Map For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. System Memory Map Register Map Address Register Name Bit Number Bit 15 0x00ca_0300 0x00ca_037e Left-Justified Signed Result Register (LJSRR) See page 442. 14 13 12 11 10 9 Bit 8 Read: S RESULT Write: Reset: Bit 7 6 Read: 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 13 12 11 10 9 Bit 8 RESULT Write: Freescale Semiconductor, Inc... Reset: Bit 15 0x00ca_0380 0x00ca_03fe Left-Justified Unsigned Result Register (LJURR) See page 442. 14 Read: RESULT Write: Reset: Bit 7 6 Read: 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 5 4 3 2 1 Bit 0 RESULT Write: Reset: Bit 7 0x00ca_0400 0x00ca_ffff Unimplemented 6 Access results in a bus monitor timeout generating an access termination transfer error. Serial Peripheral Interface (SPI) 0x00cb_0000 0x00cb_0001 P = Current pin state SPI Control Register 1 (SPICR1) See page 376. SPI Control Register 2 (SPICR2) See page 378. U = Unaffected Bit 7 6 5 4 3 2 1 Bit 0 SPIE SPE SWOM MSTR CPOL CPHA SSOE LSBFE 0 0 0 0 0 1 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 SPISDOZ SPC0 0 0 Read: Write: Reset: Read: Write: Reset: 0 0 0 0 0 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 24 of 34) MMC2107 - Rev. 2.0 MOTOROLA Technical Data System Memory Map For More Information On This Product, Go to: www.freescale.com 77 Freescale Semiconductor, Inc. System Memory Map Address Register Name Bit Number Bit 7 SPI Baud Rate Register (SPIBR) See page 379. 0x00cb_0002 SPI Status Register (SPISR) See page 381. Freescale Semiconductor, Inc... 0x00cb_0003 0x00cb_0004 5 4 SPI Data Register (SPIDR) See page 382. SPPR6 SPPR5 SPPR4 0 0 0 0 Bit 7 6 5 SPIF WCOL 0 Bit 7 0x00cb_0007 0x00cb_0008 SPI Port Data Direction Register (SPIDDR) See page 385. 0x00cb_0009 0x00cb_000f P = Current pin state Reserved U = Unaffected 3 1 Bit 0 SPR2 SPR1 SPR0 0 0 0 0 4 3 2 1 Bit 0 0 MODF 0 0 0 0 0 0 0 0 0 0 0 6 5 4 3 2 1 Bit 0 0 Write: Reset: Read: Write: Reset: Writes have no effect, reads return 0s, and the access terminates without a transfer error exception. Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 RSVD5 RDPSP RSVD1 PUPSP Read: Write: Reset: SPI Pullup and Reduced Read: Drive Register Write: (SPIPURD) See page 383. Reset: SPI Port Data Register (SPIPORT) See page 384. 2 0 Reserved 0x00cb_0005 0x00cb_0006 Read: 6 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 RSVD7 RSVD6 RSVD5 RSVD4 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 RSVD7 RSVD6 RSVD5 RSVD4 DDRSP3 DDRSP2 DDRSP1 DDRSP0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Read: PORTSP3 PORTSP2 PORTSP1 PORTSP0 Write: Reset: Read: Write: Reset: Writes have no effect, reads return 0s, and the access terminates without a transfer error exception. = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 25 of 34) Technical Data 78 MMC2107 - Rev. 2.0 System Memory Map For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. System Memory Map Register Map Address Register Name Bit Number Bit 7 0x00cb_0010 0x00cb_ffff Unimplemented 6 5 4 3 2 1 Bit 0 Access results in a bus monitor timeout generating an access termination transfer error. Freescale Semiconductor, Inc... Serial Communications Interface 1 (SCI1) and Serial Communications Interface 2 (SCI2) Note: Addresses for SCI1 are at 0x00cc_#### and addresses for SCI2 are at 0x00cd_####. 0x00cc_0000 0x00cd_0000 0x00cc_0001 0x00cd_0001 SCI Baud Rate Register High (SCIBDH) See page 336. SCI Baud Rate Register Low (SCIBDL) See page 336. 0x00cc_0002 0x00cd_0002 0x00cc_0003 0x00cd_0003 0x00cc_0004 0x00cd_0004 0x00cc_0005 0x00cd_0005 P = Current pin state SCI Control Register 1 (SCICR1) See page 337. SCI Control Register 2 (SCICR2) See page 340. SCI Status Register 1 (SCISR1) See page 342. SCI Status Register 2 (SCISR2) See page 344. U = Unaffected Read: Bit 7 6 5 0 0 0 4 3 2 1 Bit 0 SBR12 SBR11 SBR10 SBR9 SBR8 Write: Reset: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 SBR7 SBR6 SBR5 SBR4 SBR3 SBR2 SBR1 SBR0 0 0 0 0 0 1 0 0 Bit 7 6 5 4 3 2 1 Bit 0 LOOPS WOMS RSRC M WAKE ILT PE PT 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 TIE TCIE RIE ILIE TE RE RWU SBK 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 TDRE TC RDRF IDLE OR NF FE PF 1 1 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 RAF 0 0 0 0 0 0 0 0 Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 26 of 34) MMC2107 - Rev. 2.0 MOTOROLA Technical Data System Memory Map For More Information On This Product, Go to: www.freescale.com 79 Freescale Semiconductor, Inc. System Memory Map Address Register Name Bit Number Bit 7 SCI Data Register High (SCIDRH) See page 345. 0x00cc_0006 0x00cd_0006 SCI Data Register Low (SCIDRL) See page 345. Freescale Semiconductor, Inc... 0x00cc_0007 0x00cd_0007 0x00cc_0008 0x00cd_0008 Read: R8 0x00cc_000a 0x00cd_000a 0x00cc_000b 0x00cc_000f 0x00cd_000b 0x00cd_000f SCI Port Data Register (SCIPORT) See page 347. SCI Data Direction Register (SCIDDR) See page 348. Reset: P = Current pin state U = Unaffected 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Read: R7 R6 R5 R4 R3 R2 R1 R0 Write: T7 T6 T5 T4 T3 T2 T1 T0 Reset: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 RSVD5 RDPSCI RSVD1 PUPSCI 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 RSVD7 RSVD6 RSVD5 RSVD4 RSVD3 RSVD2 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 RSVD7 RSVD6 RSVD5 RSVD4 RSVD3 RSVD2 DDRSC1 DDRSC0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 Read: PORTSC1 PORTSC0 Write: Reset: Read: Write: Reset: Writes have no effect, reads return 0s, and the access terminates without a transfer error exception. Reserved Unimplemented 4 Write: Bit 7 0x00cc_0010 0x00cc_ffff 0x00cd_0010 0x00cd_ffff 5 T8 SCI Pullup and Reduced Read: SCISDOZ Drive Register Write: (SCIPURD) See page 346. Reset: 0 0x00cc_0009 0x00cd_0009 6 6 5 4 3 2 1 Bit 0 Access results in a bus monitor timeout generating an access termination transfer error. = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 27 of 34) Technical Data 80 MMC2107 - Rev. 2.0 System Memory Map For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. System Memory Map Register Map Address Register Name Bit Number Timer 1 (TIM1) and Timer 2 (TIM2) Note: Addresses for TIM1 are at 0x00ce_#### and addresses for TIM2 are at 0x00cf_####. Freescale Semiconductor, Inc... 0x00ce_0000 0x00cf_0000 Timer Input Capture/ Read: Output Compare Select Write: Register (TIMIOS) See page 300. Reset: Timer Compare Force Register (TIMCFORC) See page 301. 0x00ce_0001 0x00cf_0001 0x00ce_0002 0x00cf_0002 0x00ce_0003 0x00cf_0003 0x00ce_0004 0x00cf_0004 0x00ce_0005 0x00cf_0005 Read: Timer Counter Register High (TIMCNTH) See page 304. Timer Counter Register Low (TIMCNTL) See page 304. 0x00ce_0006 0x00cf_0006 P = Current pin state Timer System Control Register 1 (TIMSCR1) See page 305. U = Unaffected 6 5 4 0 0 0 0 Reset: Read: 3 2 1 Bit 0 IOS3 IOS2 IOS1 IOS0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 FOC3 FOC2 FOC1 FOC0 Write: Timer Output Compare 3 Read: Mask Register Write: (TIMOC3M) See page 302. Reset: Timer Output Compare 3 Data Register (TIMOC3D) See page 303. Bit 7 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 OC3M3 OC3M2 OC3M1 OC3M0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 OC3D3 OC3D2 OC3D1 OC3D0 Write: Reset: Read: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 Write: Reset: Read: Write: Reset: Read: TIMEN TFFCA Write: Reset: 0 0 0 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 28 of 34) MMC2107 - Rev. 2.0 MOTOROLA Technical Data System Memory Map For More Information On This Product, Go to: www.freescale.com 81 Freescale Semiconductor, Inc. System Memory Map Address Register Name Bit Number Bit 7 0x00ce_0007 0x00cf_0007 Freescale Semiconductor, Inc... 0x00ce_0008 0x00cf_0008 0x00ce_0009 0x00cf_0009 0x00ce_000a 0x00cf_000a 0x00ce_000b 0x00cf_000b 0x00ce_000c 0x00cf_000c 0x00ce_000d 0x00cf_000d 0x00ce_000e 0x00cf_000e P = Current pin state Timer Control Register 1 (TIMCTL1) See page 307. Timer Interrupt Enable Register (TIMIE) See page 309. Timer System Control Register 2 (TIMSCR2) See page 310. Timer Flag Register 1 (TIMFLG1) See page 312. U = Unaffected 4 Read: Bit 7 6 5 4 0 0 0 0 3 2 1 Bit 0 3 2 1 Bit 0 TOV3 TOV2 TOV1 TOV0 Write: Reset: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 OM3 OL3 OM2 OL2 OM1 OL1 OM0 OL0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Read: Write: Reset: Writes have no effect, reads return 0s, and the access terminates without a transfer error exception. Reserved Timer Control Register 2 (TIMCTL2) See page 308. 5 Writes have no effect, reads return 0s, and the access terminates without a transfer error exception. Reserved Timer Toggle on Overflow Register (TIMTOV) See page 306. 6 Bit 7 6 5 4 3 2 1 Bit 0 EDG3B EDG3A EDG2B EDG2A EDG1B EDG1A EDG0B EDG10 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 C3I C2I C1I C0I Read: Write: Reset: Read: Write: Reset: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 PUPT RDPT TCRE PR2 PR1 PR0 Read: 0 TOI Write: Reset: Read: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 C3F C2F C1F C0F 0 0 0 0 Write: Reset: 0 0 0 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 29 of 34) Technical Data 82 MMC2107 - Rev. 2.0 System Memory Map For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. System Memory Map Register Map Address Register Name Bit Number Bit 7 Timer Flag Register 2 (TIMFLG2) See page 313. 0x00ce_000f 0x00cf_000f Freescale Semiconductor, Inc... 0x00ce_0010 0x00cf_0010 0x00ce_0011 0x00cf_0011 0x00ce_0012 0x00cf_0012 0x00ce_0013 0x00cf_0013 0x00ce_0014 0x00cf_0014 0x00ce_0015 0x00cf_0015 0x00ce_0016 0x00cf_0016 Timer Channel 0 Register High (TIMC0H) See page 314. Timer Channel 0 Register Low (TIMC0L) See page 314. Timer Channel 1 Register High (TIMC1H) See page 314. Timer Channel 1 Register Low (TIMC1L) See page 314. Timer Channel 2 Register High (TIMC2H) See page 314. Timer Channel 2 Register Low (TIMC2L) See page 314. Timer Channel 3 Register High (TIMC3H) See page 314. P = Current pin state U = Unaffected 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 Read: TOF Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 30 of 34) MMC2107 - Rev. 2.0 MOTOROLA Technical Data System Memory Map For More Information On This Product, Go to: www.freescale.com 83 Freescale Semiconductor, Inc. System Memory Map Address 0x00ce_0017 0x00cf_0017 Register Name Timer Channel 3 Register Low (TIMC3L) See page 314. Freescale Semiconductor, Inc... Pulse Accumulator Flag Register (TIMPAFLG) See page 317. 0x00ce_0019 0x00cf_0019 0x00ce_001c 0x00cf_001c 0x00ce_001e 0x00cf_001e Reset: Read: 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 PAE PAMOD PEDGE CLK1 CLK0 PAOVI PAI 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 PAOVF PAIF 0 Write: Reset: Pulse Accumulator Read: Counter Register Low Write: (TIMPACNTL) See page 318. Reset: 0x00ce_001b 0x00cf_001b 6 Write: Pulse Accumulator Read: Counter Register High Write: (TIMPACNTH) See page 318. Reset: 0x00ce_001a 0x00cf_001a Bit 7 Read: Pulse Accumulator Read: Control Register Write: (TIMPACTL) See page 315. Reset: 0x00ce_0018 0x00cf_0018 0x00ce_001d 0x00cf_001d Bit Number 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Writes have no effect, reads return 0s, and the access terminates without a transfer error exception. Reserved Timer Port Data Register (TIMPORT) See page 319. Timer Port Data Direction Register (TIMDDR) See page 320. P = Current pin state U = Unaffected Read: Bit 7 6 5 4 0 0 0 0 3 2 1 Bit 0 PORTT3 PORTT2 PORTT1 PORTT0 Write: Reset: Read: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 DDRT3 DDRT2 DDRT1 DDRT0 0 0 0 0 Write: Reset: 0 0 0 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 31 of 34) Technical Data 84 MMC2107 - Rev. 2.0 System Memory Map For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. System Memory Map Register Map Address Freescale Semiconductor, Inc... 0x00ce_001f 0x00cf_001f 0x00ce_0020 0x00ce_ffff 0x00cf_0030 0x00cf_ffff Register Name Timer Test Register (TIMTST) See page 321. Bit Number Read: Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Write: Reset: Unimplemented Access results in the module generating an access termination transfer error. Non-Volatile Memory FLASH (CMFR) 0x00d0_0000 0x00d0_0001 0x00d0_0002 0x00d0_0003 CMFR Module Read: Configuration Register Write: (CMFRMCR) See page 188. Reset: Bit 31 30 FSTOP FDBG 0 0 Bit 23 29 28 27 26 25 Bit 24 EME SIE LOCKCTL DIS RSVD24 0 Note 1 0 0 Note 1 0 22 21 20 19 18 17 Bit 16 SUPV7 SUPV6 SUPV5 SUPV4 SUPV3 SUPV2 SUPV1 SUPV0 1 1 1 1 1 1 1 1 Bit 15 14 13 12 11 10 9 Bit 8 DATA7 DATA6 DATA5 DATA4 DATA3 DATA2 DATA1 DATA0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 Read: Write: Reset: Read: Write: Reset: Read: PROTECT7 PROTECT6 PROTECT5 PROTECT4 PROTECT3 PROTECT2 PROTECT1 PROTECT0 Write: Reset: 1 1 1 1 1 1 1 1 Notes: 1. Reset state is defined by reset override. P = Current pin state U = Unaffected = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 32 of 34) MMC2107 - Rev. 2.0 MOTOROLA Technical Data System Memory Map For More Information On This Product, Go to: www.freescale.com 85 Freescale Semiconductor, Inc. System Memory Map Address 0x00d0_0004 0x00d0_0005 0x00d0_0006 0x00d0_0007 Register Name CMFR Module Test Register (CMFRMTR) See page 193. Bit Number Read: Bit 31 30 29 28 27 26 25 Bit 24 0 0 0 0 0 0 0 0 Bit 23 22 21 20 19 18 17 Bit 16 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 NVR PAWS2 PAWS1 PAWS0 0 0 0 0 4 3 2 1 Bit 0 0 0 0 0 0 Write: Reset: Read: Write: Freescale Semiconductor, Inc... Reset: Read: Write: Reset: Bit 7 Read: 6 5 RSVD6 GDB 0 0 0 0 0 0 0 0 Bit 31 30 29 28 27 26 25 Bit 24 SCLKR2 SCLKR1 SCLKR0 CLKPE1 CLKPE0 0 Write: Reset: 0x00d0_0008 0x00d0_0009 0x00d0_000a 0x00d0_000b CMFR High-Voltage Read: Control Register Write: (CMFRCTL) See page 196. Reset: Read: 0 HVS 0 0 0 0 0 0 0 0 0 Bit 23 22 21 20 19 18 17 Bit 16 CLKPM6 CLKPM5 CLKPM4 CLKPM3 CLKPM2 CLKPM1 CLKPM0 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 BLOCK7 BLOCK6 BLOCK5 BLOCK4 BLOCK3 BLOCK2 BLOCK1 BLOCK0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 1 0 0 ERASE SES EHV 0 0 0 0 Write: Reset: Read: Write: Reset: Read: 0 RSVD6 Write: Reset: P = Current pin state U = Unaffected 0 0 1 0 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 33 of 34) Technical Data 86 MMC2107 - Rev. 2.0 System Memory Map For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. System Memory Map Register Map Address Register Name Bit Number Bit 7 0x00d0_000c 0x00d0_001c Unimplemented Freescale Semiconductor, Inc... P = Current pin state Unimplemented U = Unaffected 5 4 3 2 1 Bit 0 Access results in the module generating an access termination transfer error. Bit 7 0x00d0_001d 0x7fff_ffff 6 6 5 4 3 2 1 Bit 0 Access results in a bus monitor timeout generating an access termination transfer error. = Writes have no effect and the access terminates without a transfer error exception. Figure 2-2. Register Summary (Sheet 34 of 34) MMC2107 - Rev. 2.0 MOTOROLA Technical Data System Memory Map For More Information On This Product, Go to: www.freescale.com 87 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... System Memory Map Technical Data 88 MMC2107 - Rev. 2.0 System Memory Map For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 3. Chip Configuration Module (CCM) Freescale Semiconductor, Inc... 3.1 Contents 3.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 3.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 3.4 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90 3.4.1 Master Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 3.4.2 Single-Chip Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 3.4.3 Emulation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 3.4.4 Factory Access Slave Test (FAST) Mode . . . . . . . . . . . . . . 91 3.5 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 3.6 Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92 3.7 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 3.7.1 Programming Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 3.7.2 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 3.7.3 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 3.7.3.1 Chip Configuration Register . . . . . . . . . . . . . . . . . . . . . . . 94 3.7.3.2 Reset Configuration Register . . . . . . . . . . . . . . . . . . . . . . 97 3.7.3.3 Chip Identification Register . . . . . . . . . . . . . . . . . . . . . . . 99 3.7.3.4 Chip Test Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 3.8 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 3.8.1 Reset Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 3.8.2 Chip Mode Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 3.8.3 Boot Device Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 3.8.4 Output Pad Strength Configuration . . . . . . . . . . . . . . . . . .105 3.8.5 Clock Mode Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 3.8.6 Internal FLASH Configuration . . . . . . . . . . . . . . . . . . . . . . 106 3.9 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 3.10 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Chip Configuration Module (CCM) For More Information On This Product, Go to: www.freescale.com 89 Freescale Semiconductor, Inc. Chip Configuration Module (CCM) 3.2 Introduction The chip configuration module (CCM) controls the chip configuration and mode of operation. 3.3 Features Freescale Semiconductor, Inc... The CCM performs these operations. * Selects the chip operating mode: - Master mode - Single-chip mode - Emulation mode - Factory access slave test (FAST) mode for factory test only * Selects external clock or phase-lock loop (PLL) mode with internal or external reference * Selects output pad strength * Selects boot device * Selects module configuration * Selects bus monitor configuration 3.4 Modes of Operation The CCM configures the chip for four modes of operation: * Master mode * Single-chip mode * Emulation mode * FAST mode for factory test only The operating mode is determined at reset and cannot be changed thereafter. Technical Data 90 MMC2107 - Rev. 2.0 Chip Configuration Module (CCM) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Chip Configuration Module (CCM) Modes of Operation Freescale Semiconductor, Inc... 3.4.1 Master Mode In master mode, the internal central processor unit (CPU) can access external memories and peripherals. Full master mode functionality requires the bonding out of the optional pins. The external bus consists of a 32-bit data bus and 23 address lines. Available bus control signals include R/W, TC[2:0], TSIZ[1:0], TA, TEA, OE, and EB[3:0]. Up to four chip selects can be programmed to select and control external devices and to provide bus cycle termination. When interfacing to 16-bit ports, the ports C and D pins and EB[3:2] can be configured as general-purpose input/output (I/O). 3.4.2 Single-Chip Mode In single-chip mode, all memory is internal to the chip. External bus pins are configured as digital I/O. 3.4.3 Emulation Mode Emulation mode supports external port replacement logic. All ports are emulated and all primary pin functions are enabled. Since the full external bus must be visible to support the external port replacement logic, the emulation mode pin configuration resembles master mode. Full emulation mode functionality requires bonding out the optional pins. Emulation mode chip selects are provided to give additional information about the bus cycle. Also, the signal SHS is provided as a strobe for capturing addresses and data during show cycles. 3.4.4 Factory Access Slave Test (FAST) Mode FAST mode is for factory test only. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Chip Configuration Module (CCM) For More Information On This Product, Go to: www.freescale.com 91 Freescale Semiconductor, Inc. Chip Configuration Module (CCM) Freescale Semiconductor, Inc... 3.5 Block Diagram RESET CONFIGURATION OUTPUT PAD STRENGTH SELECTION CHIP MODE SELECTION CLOCK MODE SELECTION BOOT DEVICE SELECTION MODULE CONFIGURATION CHIP CONFIGURATION REGISTER RESET CONFIGURATION REGISTER CHIP IDENTIFICATION REGISTER CHIP TEST REGISTER Figure 3-1. Chip Configuration Module Block Diagram 3.6 Signal Descriptions Table 3-1 provides an overview of the CCM signals. For more detailed information, refer to Section 4. Signal Description. Table 3-1. Signal Properties Name Function RCON Reset configuration select VDDSYN Clock mode select -- D[31:16] Reset configuration overrides -- Technical Data 92 Reset State Internal weak pullup device MMC2107 - Rev. 2.0 Chip Configuration Module (CCM) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Chip Configuration Module (CCM) Memory Map and Registers 3.7 Memory Map and Registers This subsection provides a description of the memory map and registers. 3.7.1 Programming Model Freescale Semiconductor, Inc... The CCM programming model consists of these registers: * The chip configuration register (CCR) controls the main chip configuration. * The reset configuration register (RCON) indicates the default chip configuration. * The chip identification register (CIR) contains a unique part number. * The chip test register (CTR) contains chip-specific test functions. Some control register bits are implemented as write-once bits. These bits are always readable, but once the bit has been written, additional writes have no effect, except during debug mode and test operations. Some write-once bits and test bits can be read and written while in debug mode or test mode. When debug or test mode is exited, the chip configuration module resumes operation based on the current register values. If a write to a write-once register bit occurs while in debug or test mode, the register bit remains writable on exit from debug or test mode. Table 3-2 shows the accessibility of write-once bits. Table 3-2. Write-Once Bits Read/Write Accessibility Configuration Read/Write Access All configurations Read-always Debug operation (all modes) Write-always Test operation (all modes) Write-always Master mode Write-once Single-chip mode Write-once FAST mode Write-once Emulation mode Write-once MMC2107 - Rev. 2.0 MOTOROLA Technical Data Chip Configuration Module (CCM) For More Information On This Product, Go to: www.freescale.com 93 Freescale Semiconductor, Inc. Chip Configuration Module (CCM) 3.7.2 Memory Map Table 3-3. Chip Configuration Module Memory Map Address Bits 31-16 Bits 15-0 Access(1) 0x00c1_0000 Chip configuration register (CCR) Reserved (2) S 0x00c1_0004 Reset configuration register (RCON) Chip identification register (CIR) S 0x00c1_0008 Chip test register (CTR) Reserved (2) S Unimplemented(3) Freescale Semiconductor, Inc... 0x00c1_000c -- 1. S = CPU supervisor mode access only. User mode accesses to supervisor only addresses have no effect and result in a cycle termination transfer error. 2. Writing to reserved addresses has no effect; reading returns 0s. 3. Accessing an unimplemented address has no effect and causes a cycle termination transfer error. 3.7.3 Register Descriptions The following subsection describes the CCM registers. 3.7.3.1 Chip Configuration Register Address: 0x00c1_0000 and 0x00c1_0001 Bit 15 Read: 14 13 12 SHEN EMINT 0 LOAD 11 10 9 Bit 8 0 MODE2 MODE1 MODE0 Write: Reset: Read: Note 1 0 Note 2 Note 2 0 Note 1 Note 1 Note 1 Bit 7 6 5 4 3 2 1 Bit 0 SZEN PSTEN SHINT BME BMD BMT1 BMT0 Note 3 Note 2 0 1 0 0 0 0 Write: Reset: 0 = Writes have no effect and the access terminates without a transfer error exception. Notes: 1. Determined during reset configuration 2. 0 for all configurations except emulation mode, 1 for emulation mode 3. 0 for all configurations except emulation and master modes, 1 for emulation and master modes Figure 3-2. Chip Configuration Register (CCR) Technical Data 94 MMC2107 - Rev. 2.0 Chip Configuration Module (CCM) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Chip Configuration Module (CCM) Memory Map and Registers LOAD -- Pad Driver Load Bit The LOAD bit selects full or default drive strength for selected pad output drivers. For maximum capacitive load, set the LOAD bit to select full drive strength. For reduced power consumption, clear the LOAD bit to select default drive strength. 1 = Full drive strength 0 = Default drive strength Table 3-2 shows the read/write accessibility of this write-once bit. Freescale Semiconductor, Inc... SHEN -- Show Cycle Enable Bit The SHEN bit enables the external memory interface to drive the external bus during internal transfer operations. 1 = Show cycles enabled 0 = Show cycles disabled In emulation mode, the SHEN bit is read-only. In all other modes, it is a read/write bit. EMINT -- Emulate Internal Address Space Bit The EMINT bit enables chip select 1 (CS1) to decode the internal memory address space. 1 = CS1 decodes internal memory address space. 0 = CS1 decodes external memory address space. The EMINT bit is read-always but can be written only in emulation mode. MODE[2:0] -- Chip Configuration Mode Field This read-only field reflects the chip configuration mode, as shown in Table 3-4. Table 3-4. Chip Configuration Mode Selection MODE[2:0] Chip Configuration Mode 111 Master mode 110 Single-chip mode 10X FAST mode 0XX Emulation mode MMC2107 - Rev. 2.0 MOTOROLA Technical Data Chip Configuration Module (CCM) For More Information On This Product, Go to: www.freescale.com 95 Freescale Semiconductor, Inc. Chip Configuration Module (CCM) SZEN -- TSIZ[1:0] Enable Bits This read/write bit enables the TSIZ[1:0] function of the external pins. 1 = TSIZ[1:0] function enabled 0 = TSIZ[1:0] function disabled PSTEN -- PSTAT[3:0] Signal Enable Bits Freescale Semiconductor, Inc... This read/write bit enables the PSTAT[3:0] function of the external pins. 1 = PSTAT[3:0] function enabled 0 = PSTAT[3:0] function disabled SHINT -- Show Interrupt Bit The SHINT bit allows visibility to any active interrupt request to the processor. If the SHINT bit is set, the RSTOUT pin is the OR of the fast and normal interrupt signals. 1 = Internal requests reflected on RSTOUT pin 0 = Normal RSTOUT pin function The SHINT bit is read/write always. NOTE: The FRCRSTOUT function in the reset controller has a higher priority than the SHINT function. BME -- Bus Monitor External Enable Bit The BME bit enables the bus monitor to operate during external bus cycles. 1 = Bus monitor enabled on external bus cycles 0 = Bus monitor disabled on external bus cycles Table 3-2 shows the read/write accessibility of this write-once bit. BMD -- Bus Monitor Debug Mode Bit The BMD bit controls how the bus monitor responds during debug mode. 1 = Bus monitor enabled in debug mode 0 = Bus monitor disabled in debug mode This bit is read/write always. Technical Data 96 MMC2107 - Rev. 2.0 Chip Configuration Module (CCM) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Chip Configuration Module (CCM) Memory Map and Registers BMT[1:0] -- Bus Monitor Timing Field The BMT field selects the timeout time for the bus monitor as shown in Table 3-5. Freescale Semiconductor, Inc... Table 3-5. Bus Monitor Timeout Values BMT[1:0] Timeout Period (in System Clocks) 00 64 01 32 10 16 11 8 Table 3-2 shows the read/write accessibility of these write-once bits. 3.7.3.2 Reset Configuration Register The reset configuration register (RCON) is a read-only register; writing to RCON has no effect. At reset, RCON determines the default operation of certain chip functions. All default functions defined by the RCON values may be overridden during reset configuration only if the external RCON pin is asserted. Address: 0x00c1_0004 and 0x00c1_0005 Read: Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 RLOAD 0 0 0 MODE 0 0 0 0 Write: Reset: Read: 1 1 RPLLSEL RPLLREF 1 0 BOOTPS BOOTSEL Write: Reset: 1 1 1 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 3-3. Reset Configuration Register (RCON) MMC2107 - Rev. 2.0 MOTOROLA Technical Data Chip Configuration Module (CCM) For More Information On This Product, Go to: www.freescale.com 97 Freescale Semiconductor, Inc. Chip Configuration Module (CCM) RPLLSEL -- PLL Mode Select Bit When the PLL is enabled, the read-only RPLLSEL bit reflects the default PLL mode. 1 = Normal PLL mode 0 = 1:1 PLL mode The default PLL mode can be overridden during reset configuration. If the default mode is overridden, the PLLSEL bit in the clock module SYNSR reflects the PLL mode. Freescale Semiconductor, Inc... RPLLREF -- PLL Reference Bit When the PLL is enabled in normal PLL mode, the read-only RPLLREF bit reflects the default PLL reference. 1 = Crystal oscillator is PLL reference. 0 = External clock is PLL reference. The default PLL reference can be overridden during reset configuration. If the default mode is overridden, the PLLREF bit in the clock module SYNSR reflects the PLL reference. RLOAD -- Pad Driver Load Bit The read-only RLOAD bit reflects the pad driver strength configuration. 1 = Full drive strength 0 = Default drive strength The default function of the pad driver strength can be overridden during reset configuration. If the default mode is overridden, the LOAD bit in CCR reflects the pad driver strength configuration. BOOTPS -- Boot Port Size Bit If the boot device is configured to be external, the read-only BOOTPS bit reflects the default selection for the boot port size. 1 = Boot device uses 32-bit port. 0 = Boot device uses 16-bit port. The default function of the boot port size can be overridden during reset configuration. If the default mode is overridden, the PS bit in CSCR0 reflects the boot device port size configuration. BOOTSEL -- Boot Select Bit This read-only bit reflects the default selection for the boot device. 1 = Boot from external boot device 0 = Boot from internal boot device Technical Data 98 MMC2107 - Rev. 2.0 Chip Configuration Module (CCM) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Chip Configuration Module (CCM) Memory Map and Registers The default function of the boot select can be overridden during reset configuration. If the default mode is overridden, the CSEN bit in CSCR0 bit reflects the boot device configuration. MODE -- Chip Configuration Mode Bit Freescale Semiconductor, Inc... The read-only MODE bit reflects the default chip configuration mode. 1 = Master mode 0 = Single-chip mode The default mode can be overridden during reset configuration. If the default mode is overridden, the MODE0 bit in CCR reflects the mode configuration. 3.7.3.3 Chip Identification Register The chip identification register (CIR) is a read-only register; writing to CIR has no effect. Address: 0x00c1_0006 and 0x00c1_0007 Read: Bit 15 14 13 12 11 10 9 Bit 8 0 PIN7 0 PIN6 0 PIN5 1 PIN4 0 PIN3 1 PIN2 1 PIN1 1 PIN0 0 0 0 1 0 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 0 PRN7 0 PRN6 0 PRN5 0 PRN4 0 PRN3 0 PRN2 0 PRN1 0 PRN0 0 0 0 0 0 0 0 0 Write: Reset: Read: Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 3-4. Chip Identification Register (CIR) PIN[7:0] -- Part Identification Number Field This read-only field contains a unique identification number for the part. PRN[7:0] -- Part Revision Number Field This read-only field contains the full-layer mask revision number. This number is increased by one for each new full-layer mask set of this part. The revision numbers are assigned in chronological order. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Chip Configuration Module (CCM) For More Information On This Product, Go to: www.freescale.com 99 Freescale Semiconductor, Inc. Chip Configuration Module (CCM) 3.7.3.4 Chip Test Register The chip test register (CTR) is reserved for factory testing. NOTE: To safeguard against unintentionally activating test logic, write $0000 to the lock-out test features. Setting any bit in CTR may lead to unpredictable results. Freescale Semiconductor, Inc... Address: 0x00c1_0008 and 0x00c1_0009 Read: Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Write: Reset: Read: Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 3-5. Chip Test Register (CTR) 3.8 Functional Description Six functions are defined within the chip configuration module: 1. Reset configuration 2. Chip mode selection 3. Boot device selection 4. Output pad strength configuration 5. Clock mode selection 6. Module configuration These functions are described here. Technical Data 100 MMC2107 - Rev. 2.0 Chip Configuration Module (CCM) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Chip Configuration Module (CCM) Functional Description 3.8.1 Reset Configuration During reset, the pins for the reset override functions are immediately configured to known states, even if the clock source is not present. Table 3-6 shows the states of the external pins while in reset. Table 3-6. Reset Configuration Pin States During Reset Freescale Semiconductor, Inc... Pin Pin Function(1) I/O Output State Input State D[28, 26, 23:21, 19:16], PA[4, 2], PB[7:5, 3:0] Digital I/O or primary Input function -- Must be driven by external logic RCON RCON function for all Input modes(2) -- Internal weak pullup device VDDSYN Not affected -- Must be driven by external logic Input 1. If the external RCON pin is not asserted during reset, pin functions are determined by the default operation mode defined in the RCON register. If the external RCON pin is asserted, pin functions are determined by the chip operation mode defined by the override values driven on the external data bus pins. 2. During reset, the external RCON pin assumes its RCON pin function, but this pin changes to the function defined by the chip operation mode immediately after reset. See Table 3-7. If the RCON pin is not asserted during reset, the chip configuration and the reset configuration pin functions after reset are determined by RCON or fixed defaults, regardless of the states of the external data pins. The internal configuration signals are driven to levels specified by the RCON register's reset state for default module configuration. If the external RCON pin is asserted during reset, then various chip functions, including the reset configuration pin functions after reset, are configured according to the levels driven onto the external data pins. (See Table 3-7.) The internal configuration signals are driven to reflect the levels on the external configuration pins to allow for module configuration. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Chip Configuration Module (CCM) For More Information On This Product, Go to: www.freescale.com 101 Freescale Semiconductor, Inc. Chip Configuration Module (CCM) Table 3-7. Configuration During Reset(1) Pin(s) Affected Freescale Semiconductor, Inc... D[31:0], SHS, TA, TEA, CSE[1:0], TC[2:0], OE, A[22:0], EB[3:0], CS[3:0] Default Configuration VDD, VDD, RCON0 Override Pins in Reset(2),(3) Function D[26,17:16] Chip Mode Selected 111 Master mode 110 Single-chip mode 10X FAST mode 0XX Emulation mode D[19:18] CS[1:0] X0 Internal with 32-bit port 01 External with 16-bit port 11 External with 32-bit port RCON[3:2] D21 All output pins Boot Device RCON5 Output Pad Drive Strength 0 Default strength 1 Full strength VDDSYN, D[23:22] Clock mode Internal FLASH configuration VDDSYN, RCON[7:6] VDD Clock Mode 0XX External clock mode (PLL disabled) 10X 1:1 PLL mode 110 Normal PLL mode with external clock reference 111 Normal PLL mode w/crystal oscillator reference D28 Module Configuration 1 Internal FLASH enabled 0 Internal FLASH disabled 1. Modifying the default configurations is possible only if the external RCON pin is asserted. 2. The D[31:29, 27, 25:24, 20, 15:0] pins do not affect reset configuration. 3. The external reset override circuitry drives the data bus pins with the override values while RSTOUT is asserted. It must stop driving the data bus pins within one CLKOUT cycle after RSTOUT is negated. To prevent contention with the external reset override circuitry, the reset override pins are forced to inputs during reset and do not become outputs until at least one CLKOUT cycle after RSTOUT is negated. Technical Data 102 MMC2107 - Rev. 2.0 Chip Configuration Module (CCM) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Chip Configuration Module (CCM) Functional Description 3.8.2 Chip Mode Selection The chip mode is selected during reset and reflected in the MODE field of the chip configuration register (CCR). Once reset is exited, the operating mode cannot be changed. Table 3-8 shows the mode selection during reset configuration. Freescale Semiconductor, Inc... Table 3-8. Chip Configuration Mode Selection(1) Chip Configuration Mode CCR Register MODE Field MODE2 MODE1 MODE0 Master mode D26 driven high D17 driven high D16 driven high Single-chip mode D26 driven high D17 driven high D16 driven low FAST mode D26 driven high D17 driven low D16 don't care Emulation mode D26 driven low D17 don't care D16 don't care 1. Modifying the default configurations is possible only if the external RCON pin is asserted. During reset, certain module configurations depend on whether emulation mode is active as determined by the state of the internal emulation signal. 3.8.3 Boot Device Selection During reset configuration, the CS0 chip select pin is optionally configured to select an external boot device. In this case, the CSEN bit in CSCR0 is set, enabling CS0 after reset. CS0 will be asserted for the initial boot fetch accessed from address 0x0. It is assumed that the reset vector loaded from address 0x0 causes the CPU to start executing from external memory space decoded by CS0. Also, the PS bit is configured for either a 16-bit or 32-bit port size depending on the external boot device. See Table 3-9. In emulation mode, the CS1 chip select pin is optionally configured for emulating an internal memory. In emulation mode and booting from internal memory, the CSEN bit in CSCR1 is set, enabling CS1 after reset. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Chip Configuration Module (CCM) For More Information On This Product, Go to: www.freescale.com 103 Freescale Semiconductor, Inc. Chip Configuration Module (CCM) Table 3-9. Chip Select CS0 Configuration Encoding CSCR0 Register Chip Select CS0 Control CSCR1 Register CSEN Bit PS Bit CSEN Bit Chip select disabled (32-bit port size) 0 1 1(1) Chip select enabled with 16-bit port size 1 0 0 Chip select enabled with 32-bit port size 1 1 0 Freescale Semiconductor, Inc... 1. CSCR1 CSEN is initially set only in emulation mode when booting from internal memory and is cleared otherwise. Once reset is exited, the states of the CSEN and PS bits in CSCR0 and the CSEN bit in CSCR1 remain, but can be modified by software. NOTE: When booting externally, the D28 pin should be driven low during reset configuration to disable the internal FLASH located at address 0x0 so that no conflict exists with the external boot device. The boot device selection during reset configuration is summarized in Table 3-10. Table 3-10. Boot Device Selection(1) CSCR0 Register Boot Device Selection CSEN Bit CSCR1 Register PS Bit CSEN Bit Internal boot device; default 32-bit port D18 driven low D19 don't care D18 driven low External boot device with 16-bit port D18 driven high D19 driven low D18 driven high External boot device with 32-bit port D18 driven high D19 driven high D18 driven high 1. Modifying the default configurations is possible only if the external RCON pin is asserted. Technical Data 104 MMC2107 - Rev. 2.0 Chip Configuration Module (CCM) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Chip Configuration Module (CCM) Functional Description 3.8.4 Output Pad Strength Configuration Output pad strength is determined during reset configuration as shown in Table 3-11. Once reset is exited, the output pad strength configuration can be changed by programming the LOAD bit of the chip configuration register. Table 3-11. Output Pad Driver Strength Selection(1) Freescale Semiconductor, Inc... Optional Pin Function Selection CCR Register LOAD Bit Output pads configured for default strength D21 driven low Output pads configured for full strength D2 driven high 1. Modifying the default configurations is possible only if the external RCON pin is asserted low. 3.8.5 Clock Mode Selection The clock mode is selected during reset and reflected in the PLLMODE, PLLSEL, and PLLREF bits of SYNSR. Once reset is exited, the clock mode cannot be changed. Table 3-12 summarizes clock mode selection during reset configuration. Table 3-12. Clock Mode Selection(1) Synthesizer Status Register (SYNSR) Clock Mode MODE Bit PLLSEL Bit PLLREF Bit External clock mode; PLL disabled VDDSYN driven low D23 don't care D22 don't care 1:1 PLL mode VDDSYN driven high D23 driven low D22 don't care Normal PLL mode; external clock reference VDDSYN driven high D23 driven high D22 driven low Normal PLL mode; crystal oscillator reference VDDSYN driven high D23 driven high D22 driven high 1. Modifying the default configurations is possible only if the external RCON pin is asserted low. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Chip Configuration Module (CCM) For More Information On This Product, Go to: www.freescale.com 105 Freescale Semiconductor, Inc. Chip Configuration Module (CCM) 3.8.6 Internal FLASH Configuration During reset configuration, the D28 pin controls whether or not the internal FLASH is enabled or disabled as shown in Table 3-13. Table 3-13. Internal FLASH Configuration(1) Freescale Semiconductor, Inc... Internal FLASH Configuration External D28 State Internal FLASH enabled D28 pin driven high Internal FLASH disabled D28 pin driven low 1. Modifying the default configurations is possible only if the external RCON pin is asserted low. 3.9 Reset Reset initializes CCM registers to a known startup state as described in 3.7 Memory Map and Registers. The CCM controls chip configuration at reset as described in 3.8 Functional Description. 3.10 Interrupts The CCM does not generate interrupt requests. Technical Data 106 MMC2107 - Rev. 2.0 Chip Configuration Module (CCM) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 4. Signal Description Freescale Semiconductor, Inc... 4.1 Contents 4.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 4.3 Package Pinout Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 4.4 MMC2107 Specific Implementation Signal Issues . . . . . . . . .120 4.4.1 RSTOUT Signal Functions . . . . . . . . . . . . . . . . . . . . . . . . . 120 4.4.2 INT Signal Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 4.5 Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121 4.5.1 Reset Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 4.5.1.1 Reset In (RESET) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 4.5.1.2 Reset Out (RSTOUT). . . . . . . . . . . . . . . . . . . . . . . . . . . 121 4.5.2 Phase-Lock Loop (PLL) and Clock Signals . . . . . . . . . . . . 122 4.5.2.1 External Clock In (EXTAL) . . . . . . . . . . . . . . . . . . . . . . .122 4.5.2.2 Crystal (XTAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 4.5.2.3 Clock Out (CLKOUT) . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 4.5.2.4 Synthesizer Power (VDDSYN and VSSSYN) . . . . . . . . . . . 122 4.5.3 External Memory Interface Signals . . . . . . . . . . . . . . . . . .122 4.5.3.1 Data Bus (D[31:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 4.5.3.2 Show Cycle Strobe (SHS) . . . . . . . . . . . . . . . . . . . . . . .123 4.5.3.3 Transfer Acknowledge (TA) . . . . . . . . . . . . . . . . . . . . . . 123 4.5.3.4 Transfer Error Acknowledge (TEA) . . . . . . . . . . . . . . . . 123 4.5.3.5 Emulation Mode Chip Selects (CSE[1:0]) . . . . . . . . . . . 123 4.5.3.6 Transfer Code (TC[2:0]) . . . . . . . . . . . . . . . . . . . . . . . . . 123 4.5.3.7 Read/Write (R/W). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 4.5.3.8 Address Bus (A[22:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . 124 4.5.3.9 Enable Byte (EB[3:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . 124 4.5.3.10 Chip Select (CS[3:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 4.5.3.11 Output Enable (OE) . . . . . . . . . . . . . . . . . . . . . . . . . . . .124 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Signal Description For More Information On This Product, Go to: www.freescale.com 107 Freescale Semiconductor, Inc. Signal Description Freescale Semiconductor, Inc... 4.5.4 4.5.4.1 4.5.4.2 4.5.4.3 4.5.5 4.5.5.1 4.5.5.2 4.5.5.3 4.5.5.4 4.5.6 4.5.6.1 4.5.6.2 4.5.7 4.5.8 4.5.8.1 4.5.8.2 4.5.8.3 4.5.8.4 4.5.9 4.5.9.1 4.5.9.2 4.5.9.3 4.5.9.4 4.5.9.5 4.5.9.6 4.5.10 4.5.11 4.5.11.1 4.5.11.2 4.5.11.3 4.5.11.4 4.5.11.5 Edge Port Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 External Interrupts (INT[7:6]) . . . . . . . . . . . . . . . . . . . . . 124 External Interrupts (INT[5:2]) . . . . . . . . . . . . . . . . . . . . . 124 External Interrupts (INT[1:0]) . . . . . . . . . . . . . . . . . . . . . 125 Serial Peripheral Interface Module Signals . . . . . . . . . . . . 125 Master Out/Slave In (MOSI). . . . . . . . . . . . . . . . . . . . . . 125 Master In/Slave Out (MISO). . . . . . . . . . . . . . . . . . . . . . 125 Serial Clock (SCK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 Slave Select (SS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 Serial Communications Interface Module Signals . . . . . . . 125 Receive Data (RXD1 and RXD2) . . . . . . . . . . . . . . . . . . 125 Transmit Data (TXD1 and TXD2). . . . . . . . . . . . . . . . . . 126 Timer Signals (ICOC1[3:0] and ICOC2[3:0]) . . . . . . . . . . . 126 Analog-to-Digital Converter Signals . . . . . . . . . . . . . . . . . . 126 Analog Inputs (PQA[4:3], PQA[1:0], . . . . . . . . . . . . . . . . . . and PQB[3:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 Analog Reference (VRH and VRL) . . . . . . . . . . . . . . . . . 126 Analog Supply (VDDA and VSSA) . . . . . . . . . . . . . . . . . .126 Positive Supply (VDDH) . . . . . . . . . . . . . . . . . . . . . . . . . 126 Debug and Emulation Support Signals . . . . . . . . . . . . . . . 127 Test Reset (TRST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 Test Clock (TCLK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 Test Mode Select (TMS) . . . . . . . . . . . . . . . . . . . . . . . . 127 Test Data Input (TDI) . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 Test Data Output (TDO). . . . . . . . . . . . . . . . . . . . . . . . . 127 Debug Event (DE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 Test Signal (TEST). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Power and Ground Signals . . . . . . . . . . . . . . . . . . . . . . . . 128 Power for FLASH Erase/Program (VPP) . . . . . . . . . . . . 128 Power and Ground for FLASH Array (VDDF and VSSF) . . . . . . . . . . . . . . . . . . . . . . . . . . . .128 Standby Power (VSTBY) . . . . . . . . . . . . . . . . . . . . . . . . . 128 Positive Supply (VDD). . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Ground (VSS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128 Technical Data 108 MMC2107 - Rev. 2.0 Signal Description For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Signal Description Introduction 4.2 Introduction Freescale Semiconductor, Inc... The MMC2107 is available in two packages: * 100-pin Joint-Electron Device Engineering Council (JEDEC) low-profile quad flat pack (LQFP) -- The 100-pin device is a minimum pin set for single-chip mode implementation. * 144-pin JEDEC LQFP -- The 144-pin implementation includes 44 optional pins as a bond-out option to: - Accommodate an expanded set of features - Allow expansion of the number of general-purpose input/output (I/O) - Utilize off-chip memory - Provide enhanced support for development purposes The optional group of pins includes: NOTE: * 23 address output lines * Four chip selects * Two emulation chip selects * Four byte/write enables * Read/write (R/W) signal * Output enable signal * Three transfer code signals * Six power/ground pins The optional pins are either all present or none of them are present. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Signal Description For More Information On This Product, Go to: www.freescale.com 109 Freescale Semiconductor, Inc. Signal Description 4.3 Package Pinout Summary Refer to: * Table 4-1 for a summary of the pinouts for both packages * Figure 4-1 and Figure 4-2 for a pictorial view of the pinouts * Table 4-2 for a brief description of each signal Table 4-1. Package Pinouts (Sheet 1 of 5) Freescale Semiconductor, Inc... Pin Number 100-Pin Package 1 1 D30 / PA6 2 2 D29 / PA5 3 3 D28 / PA4 4 4 D27 / PA3 5 5 D26 / PA2 6 -- A11 7 6 D25 / PA1 8 -- VSS 9 -- VDD 10 7 D24 / PA0 11 -- A10 12 8 D23 / PB7 13 -- A9 14 -- A8 15 9 D22 / PB6 16 10 D21 / PB5 17 11 D20 / PB4 18 12 VSS 19 13 VDD 20 14 D19 / PB3 21 15 D18 / PB2 22 16 D17 / PB1 23 -- A7 24 -- A6 Technical Data 110 Pin Name 144-Pin Package MMC2107 - Rev. 2.0 Signal Description For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Signal Description Package Pinout Summary Table 4-1. Package Pinouts (Sheet 2 of 5) Freescale Semiconductor, Inc... Pin Number 100-Pin Package 25 17 D16 / PB0 26 -- A5 27 18 D15 / PC7 28 -- A4 29 -- A3 30 19 D14 / PC6 31 20 D13 / PC5 32 21 VSS 33 22 VDD 34 23 D12 / PC4 35 24 D11 / PC3 36 25 D10 / PC2 37 26 D9 / PC1 38 27 D8 / PC0 39 28 D7 / PD7 40 29 D6 / PD6 41 30 D5 / PD5 42 31 D4 / PD4 43 32 D3 / PD3 44 -- VSS 45 -- VDD 46 33 D2 / PD2 47 -- A2 48 34 D1 / PD1 49 -- A1 50 -- A0 51 35 D0 / PD0 52 36 ICOC23 53 37 ICOC22 54 38 ICOC21 55 39 ICOC20 MMC2107 - Rev. 2.0 MOTOROLA Pin Name 144-Pin Package Technical Data Signal Description For More Information On This Product, Go to: www.freescale.com 111 Freescale Semiconductor, Inc. Signal Description Table 4-1. Package Pinouts (Sheet 3 of 5) Freescale Semiconductor, Inc... Pin Number 100-Pin Package 56 40 ICOC13 57 41 ICOC12 58 42 ICOC11 59 -- R/W 60 -- CSE1 61 43 ICOC10 62 -- CSE0 63 44 TEST 64 -- VSS 65 -- VDD 66 45 TXD2 67 -- TC2 68 46 RXD2 69 47 TXD1 70 48 RXD1 71 49 INT0 72 50 INT1 73 51 VSSF 74 52 VDDF 75 53 INT2 76 54 VSS 77 55 VDD 78 -- TC1 79 56 INT3 80 -- TC0 81 -- CS3 82 57 INT4 83 -- CS2 84 58 INT5 85 -- CS1 Technical Data 112 Pin Name 144-Pin Package MMC2107 - Rev. 2.0 Signal Description For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Signal Description Package Pinout Summary Table 4-1. Package Pinouts (Sheet 4 of 5) Freescale Semiconductor, Inc... Pin Number 100-Pin Package 86 -- CS0 87 59 VPP 88 60 INT6 89 61 INT7 90 62 MOSI 91 63 MISO 92 64 VSTBY 93 65 SCK 94 66 SS 95 -- OE 96 -- EB3 97 67 SHS / PE7 98 -- EB2 99 68 TA / PE6 100 -- EB1 101 -- EB0 102 69 TEA / PE5 103 70 VDDH 104 71 PQB3 105 72 PQB2 106 73 PQB1 107 74 PQB0 108 75 PQA4 109 76 PQA3 110 77 PQA1 111 78 PQA0 112 79 VRL 113 80 VRH 114 81 VSSA 115 82 VDDA MMC2107 - Rev. 2.0 MOTOROLA Pin Name 144-Pin Package Technical Data Signal Description For More Information On This Product, Go to: www.freescale.com 113 Freescale Semiconductor, Inc. Signal Description Table 4-1. Package Pinouts (Sheet 5 of 5) Freescale Semiconductor, Inc... Pin Number 100-Pin Package 116 -- A22 117 -- A21 118 83 RESET 119 -- A20 120 84 RSTOUT 121 -- A19 122 -- A18 123 85 VDDSYN 124 86 XTAL 125 87 EXTAL 126 88 VSSSYN 127 89 VSS 128 90 CLKOUT 129 91 VDD 130 92 TCLK 131 -- A17 132 -- A16 133 93 TDI 134 -- A15 135 94 TDO 136 -- A14 137 -- A13 138 95 TMS 139 -- A12 140 96 VSS 141 97 VDD 142 98 TRST 143 99 DE 144 100 D31 / PA7 Technical Data 114 Pin Name 144-Pin Package MMC2107 - Rev. 2.0 Signal Description For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 PQA4 PQB0 PQB1 PQB2 PQB3 VDDH TEA EB0 EB1 TA EB2 SHS EB3 OE SS SCK VSTBY MISO MOSI INT7 INT6 VPP CS0 CS1 INT5 CS2 INT4 CS3 TC0 INT3 TC1 VDD VSS INT2 VDDF VSSF 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 D30 D29 D28 D27 D26 A11 D25 VSS VDD D24 A10 D23 A9 A8 D22 D21 D20 VSS VDD D19 D18 D17 A7 A6 D16 A5 D15 A4 A3 D14 D13 VSS VDD D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 VSS VDD D2 A2 D1 A1 A0 D0 ICOC23 ICOC22 ICOC21 ICOC20 ICOC13 ICOC12 ICOC11 R/W CSE1 ICOC10 CSE0 TEST VSS VDD TXD2 TC2 RXD2 TXD1 RXD1 INT0 INT1 Freescale Semiconductor, Inc... 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 D31 DE TRST VDD VSS A12 TMS A13 A14 TDO A15 TDI A16 A17 TCLK VDD CLKOUT VSS VSSSYN EXTAL XTAL VDDSYN A18 A19 RSTOUT A20 RESET A21 A22 VDDA VSSA VRH VRL PQA0 PQA1 PQA3 Signal Description Package Pinout Summary Figure 4-1. 144-Pin LQFP Assignments MMC2107 - Rev. 2.0 MOTOROLA Technical Data Signal Description For More Information On This Product, Go to: www.freescale.com 115 Freescale Semiconductor, Inc. PQA1 PQA3 78 77 76 VRH VRL PQA0 80 79 VDDA VSSA 82 81 RSTOUT RESET 85 84 83 EXTAL XTAL VDDSYN 87 86 VSS VSSSYN 90 89 88 TCLK VDD CLKOUT 92 91 TDO TDI 94 93 VSS TMS 97 96 95 DE TRST VDD 1 2 3 75 PQA4 PA5 PA4 74 73 PA3 PA2 PA1 4 5 72 71 PQB0 PQB1 PQB2 6 7 70 11 12 54 47 48 TXD1 RXD1 INT0 51 MISO MOSI INT7 INT6 VPP INT5 INT4 INT3 VDD VSS INT2 VDDF VSSF INT1 45 46 TXD2 RXD2 49 50 43 44 41 42 ICOC11 ICOC10 TEST 39 40 53 52 ICOC13 ICOC12 23 24 25 ICOC21 ICOC20 PC4 PC3 PC2 VSTBY 56 55 37 38 21 22 35 36 VSS VDD 64 63 58 57 PD0 ICOC23 ICOC22 18 19 20 SS SCK 59 33 34 PC7 PC6 PC5 66 65 61 60 PD2 PD1 16 17 31 32 PB1 PB0 67 62 PD4 PD3 13 14 15 PC1 PC0 PB3 PB2 29 30 PB4 VSS VDD 8 9 10 27 28 PB6 PB5 PQB3 VDDH PE5 PE6 PE7 69 68 PD7 PD6 PD5 PA0 PB7 26 PA6 Freescale Semiconductor, Inc... 99 98 100 PA7 Signal Description Figure 4-2. 100-Pin LQFP Assignments Technical Data 116 MMC2107 - Rev. 2.0 Signal Description For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Signal Description Package Pinout Summary Table 4-2. Signal Descriptions (Sheet 1 of 3) Name (1) Alternate Qty. Dir. Input Input Hyst. Sync.(2) Drive Strength Pullup (4) Control(3) Output Driver (ST/OD/SP)(5) Reset RESET -- 1 I/O(6) Y Y -- Pullup -- RSTOUT SHOWINT 1 I/O(6) -- -- LOAD -- ST Freescale Semiconductor, Inc... Clock EXTAL -- 1 I N N -- -- SP XTAL -- 1 O -- -- -- -- SP CLKOUT -- 1 I/O(6) -- -- LOAD -- ST VDDSYN -- 1 I -- -- -- -- -- VSSSYN -- 1 I -- -- -- -- -- External Memory Interface and Ports D[31:0] PA[7:0], PB[7:0] PC[7:0], PD[7:0] 32 I/O Y Y LOAD -- ST SHS RCON / PE7 1 I/O Y Y LOAD Pullup ST TA PE6 1 I/O Y Y LOAD Pullup ST TEA PE5 1 I/O Y Y LOAD Pullup ST CSE[1:0] PE[4:3] 2 I/O Y Y LOAD Pullup ST TC[2:0] PE[2:0] 3 I/O Y Y LOAD Pullup ST R/W PF7 1 I/O Y Y LOAD Pullup ST A[22:0] PF[6:0], PG[7:0] PH[7:0] 23 I/O Y Y LOAD Pullup ST EB[3:0] PI[7:4] 4 I/O Y Y LOAD Pullup ST CS[3:0] PI[3:0] 4 I/O Y Y LOAD Pullup ST OE -- 1 I/O(6) -- -- LOAD -- ST Edge Port INT[7:6] TSIZ[1:0] / GPIO 2 I/O Y Y LOAD -- -- INT[5:2] PSTAT[3:0] / GPIO 4 I/O Y Y LOAD -- -- INT[1:0] GPIO 2 I/O Y Y LOAD -- -- MMC2107 - Rev. 2.0 MOTOROLA Technical Data Signal Description For More Information On This Product, Go to: www.freescale.com 117 Freescale Semiconductor, Inc. Signal Description Table 4-2. Signal Descriptions (Sheet 2 of 3) Name(1) Alternate Qty. Dir. Input Input Hyst. Sync.(2) Drive Strength Control(3) Pullup(4) Output Driver (ST/OD/SP)(5) Freescale Semiconductor, Inc... Serial Peripheral Interface (SPI) MOSI GPIO 1 I/O Y Y RDPSP0 Pullup(4) ST / OD (7) MISO GPIO 1 I/O Y Y RDPSP0 Pullup(4) ST / OD (7) SCK GPIO 1 I/O Y Y RDPSP0 Pullup(4) ST / OD (7) SS GPIO 1 I/O Y Y RDPSP0 Pullup(4) ST / OD (7) Serial Communication Interface (SCI1 and SCI2) TXD1 GPIO 1 I/O Y Y RDPSCI0 Pullup(4) ST / OD (7) RXD1 GPIO 1 I/O Y Y RDPSCI0 Pullup(4) ST / OD (7) TXD2 GPIO 1 I/O Y Y RDPSCI0 Pullup(4) ST / OD (7) RXD2 GPIO 1 I/O Y Y RDPSCI0 Pullup(4) ST / OD (7) Timer 1 and Timer 2 ICOC13 IC / OC / PAI / GPIO 1 I/O Y Y RDPT Pullup(4) ST ICOC1[2:0] IC / OC / GPIO 3 I/O Y Y RDPT Pullup(4) ST ICOC23 IC / OC / PAI / GPIO 1 I/O Y Y RDPT Pullup(4) ST ICOC2[2:0] IC / OC / GPIO 3 I/O Y Y RDPT Pullup(4) ST Queued Analog-to-Digital Converter (QADC) PQA4-PQA3, PQA1-PQA0 GPIO 4 I/O Y Y -- -- ST PQB[3:0] GPI 4 I Y Y -- -- -- VRH -- 1 I -- -- -- -- -- VRL -- 1 I -- -- -- -- -- VDDA -- 1 I -- -- -- -- -- VSSA -- 1 I -- -- -- -- -- VDDH -- 1 I -- -- -- -- -- Technical Data 118 MMC2107 - Rev. 2.0 Signal Description For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Signal Description Package Pinout Summary Table 4-2. Signal Descriptions (Sheet 3 of 3) Name(1) Alternate Qty. Dir. Input Input Hyst. Sync.(2) Drive Strength Control(3) Pullup(4) Output Driver (ST/OD/SP)(5) Freescale Semiconductor, Inc... Debug and JTAG Test Port Control TRST -- 1 I Y N -- Pullup -- TCLK -- 1 I Y N -- Pullup -- TMS -- 1 I Y N -- Pullup -- TDI -- 1 I Y N -- Pullup -- TDO -- 1 O(8) -- -- LOAD -- ST DE -- 1 I/O Y N LOAD Pullup OD N -- -- -- Test TEST -- 1 I Y Power Supplies VPP -- 1 I -- -- -- -- -- VDDF -- 1 I -- -- -- -- -- VSSF -- 1 I -- -- -- -- -- VSTBY -- 1 I -- -- -- -- -- VDD -- 5 I -- -- -- -- -- VSS -- 5 I -- -- -- -- -- VDD -- 3 I -- -- -- -- -- VSS -- 3 I -- -- -- -- -- Total 100 Total with optional pins 144 1. Shaded signals are for optional bond-out for 144-pin package. 2. Synchronized input used only if signal configured as a digital I/O. RESET signal is always synchronized, except in lowpower stop mode. 3. LOAD (chip configuration register bit), RDPSP0 (SPIPURD register bit in SPI), RDPSCI0 (SCIPURD register bit in both SCIs), RDPT (TIMSCR2 register bit in both timers) 4. All pullups are disconnected when the signal is programmed as an output. 5. Output driver type: ST = standard, OD = standard driver with open-drain pulldown option selected, SP = special 6. Digital input function for RSTOUT, CLKOUT, OE, and digital output function for RESET used only for JTAG boundary scan 7. Open-drain and pullup function selectable via programmer's model in module configuration registers 8. Three-state output with no input function MMC2107 - Rev. 2.0 MOTOROLA Technical Data Signal Description For More Information On This Product, Go to: www.freescale.com 119 Freescale Semiconductor, Inc. Signal Description 4.4 MMC2107 Specific Implementation Signal Issues Most modules are designed to allow expanded capabilities if all the module signals to the pads are implemented. This subsection discusses how these modules are implemented on the MMC2107. 4.4.1 RSTOUT Signal Functions Freescale Semiconductor, Inc... The RSTOUT signal has these multiple functions: CAUTION: * Whenever the internal system reset is asserted, the RSTOUT signal will always be asserted to indicate the reset condition to the system. * If the internal reset is not asserted, then setting the FRCRSTOUT bit in the reset control register will assert the RSTOUT signal for as long as the FRCRSTOUT bit is set. * If the internal reset is not asserted and the FRCRSTOUT bit is not set, then setting the SHOWINT bit in the chip configuration register will reflect internal interrupt requests out to the RSTOUT signal. * If the internal reset is not asserted and the FRCRSTOUT bit is not set and the SHOWINT bit is not set, then the RSTOUT signal will be negated to indicate to the system that there is no reset condition. External logic used to drive reset configuration data during reset needs to be considered when using the RSTOUT signal for a function other than an indication of reset. Technical Data 120 MMC2107 - Rev. 2.0 Signal Description For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Signal Description Signal Descriptions 4.4.2 INT Signal Functions Freescale Semiconductor, Inc... The INT signals have these multiple functions: NOTE: * If the SZEN bit in the chip configuration register is set, then INT[7:6] will be used to reflect the state of the TSIZ[1:0] signals from the M*CORE. * If the PSTEN bit in the chip configuration register is set, then INT[5:2] will be used to reflect the state of the PSTAT[3:0] signals from the M*CORE. If the SZEN or PSTEN bits are set during emulation mode, then the corresponding edge port INT functions are lost and will not be emulated externally. The default reset values for PUPSCI1 and PUPSCI0 will be 0. Thus, the pullup function is disabled by default. 4.5 Signal Descriptions This subsection provides a brief description of the signals. For more detailed information, reference the module section. 4.5.1 Reset Signals These signals are used to either reset the chip or as a reset indication. 4.5.1.1 Reset In (RESET) This active-low input signal is used as an external reset request. 4.5.1.2 Reset Out (RSTOUT) This active-low output signal is an indication that the internal reset controller has reset the chip. When RSTOUT is active, the user may drive override options on the data bus. RSTOUT is three-stated in phase-lock loop (PLL) test mode. RSTOUT may also be used to reflect an indication of an internal interrupt request. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Signal Description For More Information On This Product, Go to: www.freescale.com 121 Freescale Semiconductor, Inc. Signal Description 4.5.2 Phase-Lock Loop (PLL) and Clock Signals These signals are used to support the on-chip clock generation circuitry. 4.5.2.1 External Clock In (EXTAL) Freescale Semiconductor, Inc... This input signal is always driven by an external clock input except when used as a connection to the external crystal when the internal oscillator circuit is used. The clock source is configured during reset. 4.5.2.2 Crystal (XTAL) This output signal is used as a connection to the external crystal when the internal oscillator circuit is used. XTAL should be grounded when using an external clock input. 4.5.2.3 Clock Out (CLKOUT) This output signal reflects the internal system clock. 4.5.2.4 Synthesizer Power (VDDSYN and VSSSYN) These are dedicated quiet power and ground supply signals for the frequency synthesizer circuit. 4.5.3 External Memory Interface Signals In addition to the function stated here, these signals can be configured as discrete I/O signals also. 4.5.3.1 Data Bus (D[31:0]) These three-state bidirectional signals provide the general-purpose data path between the microcontroller unit (MCU) and all other devices. Technical Data 122 MMC2107 - Rev. 2.0 Signal Description For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Signal Description Signal Descriptions 4.5.3.2 Show Cycle Strobe (SHS) This output signal is used in emulation mode as a strobe for capturing addresses, controls, and data during show cycles. This signal is also used as RCON. NOTE: This input signal, used only during reset, indicates whether the states on the external signals affect the chip configuration. Freescale Semiconductor, Inc... 4.5.3.3 Transfer Acknowledge (TA) This signal indicates that the external data transfer is complete. During a read cycle, when the processor recognizes TA, it latches the data and then terminates the bus cycle. During a write cycle, when the processor recognizes TA, the bus cycle is terminated. This signal is an input in master and emulation modes. 4.5.3.4 Transfer Error Acknowledge (TEA) This signal indicates an error condition exists for the bus transfer. The bus cycle is terminated and the central processor unit (CPU) begins execution of the access error exception. This signal is an input in master and emulation modes. 4.5.3.5 Emulation Mode Chip Selects (CSE[1:0]) These output signals provide information for development support. 4.5.3.6 Transfer Code (TC[2:0]) These output signals indicate the data transfer code for the current bus cycle. 4.5.3.7 Read/Write (R/W) This output signal indicates the direction of the data transfer on the bus. A logic 1 indicates a read from a slave device and a logic 0 indicates a write to a slave device. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Signal Description For More Information On This Product, Go to: www.freescale.com 123 Freescale Semiconductor, Inc. Signal Description 4.5.3.8 Address Bus (A[22:0]) These output signals provide the address for the current bus transfer. 4.5.3.9 Enable Byte (EB[3:0]) These output signals indicate which byte of data is valid during external cycles. Freescale Semiconductor, Inc... 4.5.3.10 Chip Select (CS[3:0]) These output signals select external devices for external bus transactions. 4.5.3.11 Output Enable (OE) This output signal indicates when an external device can drive data during external read cycles. 4.5.4 Edge Port Signals These signals are used by the edge port module. 4.5.4.1 External Interrupts (INT[7:6]) These bidirectional signals function as either external interrupt sources or GPIO. Also, these signals may be used to reflect the internal TSIZ[1:0] signals and externally to provide an indication of the M*CORE transfer size. 4.5.4.2 External Interrupts (INT[5:2]) These bidirectional signals function as either external interrupt sources or GPIO. Also, these signals may be used to reflect the internal PSTAT[3:0] signals and externally to provide an indication of the M*CORE processor status. Technical Data 124 MMC2107 - Rev. 2.0 Signal Description For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Signal Description Signal Descriptions 4.5.4.3 External Interrupts (INT[1:0]) These bidirectional signals function as either external interrupt sources or GPIO. 4.5.5 Serial Peripheral Interface Module Signals Freescale Semiconductor, Inc... These signals are used by the SPI module and may also be configured to be discrete I/O signals. 4.5.5.1 Master Out/Slave In (MOSI) This signal is the serial data output from the SPI in master mode and the serial data input in slave mode. 4.5.5.2 Master In/Slave Out (MISO) This signal is the serial data input to the SPI in master mode and the serial data output in slave mode. 4.5.5.3 Serial Clock (SCK) The serial clock synchronizes data transmissions between master and slave devices. SCK is an output if the SPI is configured as a master and SCK is an input if the SPI is configured as a slave. 4.5.5.4 Slave Select (SS) This I/O signal is the peripheral chip select signal in master mode and is an active-low slave select in slave mode. 4.5.6 Serial Communications Interface Module Signals These signals are used by the two SCI modules. 4.5.6.1 Receive Data (RXD1 and RXD2) These signals are used for the SCI receiver data input and are also available for GPIO when not configured for receiver operation. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Signal Description For More Information On This Product, Go to: www.freescale.com 125 Freescale Semiconductor, Inc. Signal Description 4.5.6.2 Transmit Data (TXD1 and TXD2) These signals are used for the SCI transmitter data output and are also available for GPIO when not configured for transmitter operation. 4.5.7 Timer Signals (ICOC1[3:0] and ICOC2[3:0]) Freescale Semiconductor, Inc... These signals provide the external interface to the timer functions. They may be configured as general-purpose I/O if the timer output function is not needed. The default state at reset is general-purpose input. 4.5.8 Analog-to-Digital Converter Signals These signals are used by the analog-to-digital converter (QADC) module. 4.5.8.1 Analog Inputs (PQA[4:3], PQA[1:0], and PQB[3:0]) These signals provide the analog inputs to the QADC. The PQA signals may also be used as general-purpose digital I/O. The PQB signals may also be used as general-purpose digital inputs. 4.5.8.2 Analog Reference (VRH and VRL) These signals serve as the high (VRH) and low (VRL) reference potentials for the analog converter. 4.5.8.3 Analog Supply (VDDA and VSSA) These dedicated power supply signals isolate the sensitive analog circuitry from the normal levels of noise present on the digital power supply. 4.5.8.4 Positive Supply (VDDH) This signal supplies positive power to the ESD structures in the QADC pads. Technical Data 126 MMC2107 - Rev. 2.0 Signal Description For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Signal Description Signal Descriptions 4.5.9 Debug and Emulation Support Signals These signals are used as the interface to the on-chip JTAG (Joint Test Action Group) controller and also to interface to the OnCE logic. 4.5.9.1 Test Reset (TRST) Freescale Semiconductor, Inc... This active-low input signal is used to initialize the JTAG and OnCE logic asynchronously. 4.5.9.2 Test Clock (TCLK) This input signal is the test clock used to synchronize the JTAG and OnCE logic. 4.5.9.3 Test Mode Select (TMS) This input signal is used to sequence the JTAG state machine. TMS is sampled on the rising edge of TCLK. 4.5.9.4 Test Data Input (TDI) This input signal is the serial input for test instructions and data. TDI is sampled on the rising edge of TCLK. 4.5.9.5 Test Data Output (TDO) This output signal is the serial output for test instructions and data. TDO is three-stateable and is actively driven in the shift-IR and shift-DR controller states. TDO changes on the falling edge of TCLK. 4.5.9.6 Debug Event (DE) This is a bidirectional, active-low signal. As an output, this signal will be asserted for three system clocks, synchronous to the rising CLKOUT edge, to acknowledge that the CPU has entered debug mode as a result of a debug request or a breakpoint condition. As an input, this signal provides multiple functions. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Signal Description For More Information On This Product, Go to: www.freescale.com 127 Freescale Semiconductor, Inc. Signal Description 4.5.10 Test Signal (TEST) This input signal (TEST) is reserved for factory testing only and should be connected to VSS to prevent unintentional activation of test functions. Freescale Semiconductor, Inc... 4.5.11 Power and Ground Signals These signals provide system power and ground to the chip. Multiple signals are provided for adequate current capability. All power supply signals must have adequate bypass capacitance for high-frequency noise suppression. 4.5.11.1 Power for FLASH Erase/Program (VPP) This signal supplies an isolated power for FLASH program and erase operations. 4.5.11.2 Power and Ground for FLASH Array (VDDF and VSSF) These signals supply an isolated power and ground to the FLASH array. 4.5.11.3 Standby Power (VSTBY) This signal is used to provide standby voltage to the RAM array if VDD is lost. 4.5.11.4 Positive Supply (VDD) This signal supplies positive power to the core logic and I/O pads. 4.5.11.5 Ground (VSS) This signal is the negative supply (ground) to the chip. Technical Data 128 MMC2107 - Rev. 2.0 Signal Description For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 5. Reset Controller Module Freescale Semiconductor, Inc... 5.1 Contents 5.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 5.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 5.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 5.5 Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 5.6 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 132 5.6.1 Reset Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . .133 5.6.2 Reset Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 5.6.3 Reset Test Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 5.7 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 5.7.1 Reset Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 5.7.1.1 Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 5.7.1.2 External Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 5.7.1.3 Watchdog Timer Reset . . . . . . . . . . . . . . . . . . . . . . . . . 137 5.7.1.4 Loss of Clock Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . .137 5.7.1.5 Loss of Lock Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 5.7.1.6 Software Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 5.7.2 Reset Control Flow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 5.7.2.1 Synchronous Reset Requests . . . . . . . . . . . . . . . . . . . . 138 5.7.2.2 Internal Reset Request . . . . . . . . . . . . . . . . . . . . . . . . . 140 5.7.2.3 Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 5.7.3 Concurrent Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 5.7.3.1 Reset Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 5.7.3.2 Reset Status Flags. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 5.8 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Reset Controller Module For More Information On This Product, Go to: www.freescale.com 129 Freescale Semiconductor, Inc. Reset Controller Module 5.2 Introduction The reset controller is provided to: * Determine the cause of reset * Assert the appropriate reset signals to the system * Keep a history of what caused the reset Freescale Semiconductor, Inc... 5.3 Features Features of the reset controller module include: * Six sources of reset: - - - - - - External Power-on reset (POR) Watchdog timer Phase-lock loop (PLL) loss of lock PLL loss of clock Software * Software can assert external RSTOUT pin independent of chip reset state. * Software readable status flags indicating the cause of the last reset Technical Data 130 MMC2107 - Rev. 2.0 Reset Controller Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Reset Controller Module Block Diagram 5.4 Block Diagram Figure 5-1 shows the structure of the reset controller. RESET PIN Freescale Semiconductor, Inc... POWER-ON RESET RSTOUT PIN WATCHDOG TIMER TIMEOUT TO INTERNAL RESETS RESET CONTROLLER PLL LOSS OF CLOCK PLL LOSS OF LOCK SOFTWARE RESET Figure 5-1. Reset Controller Block Diagram 5.5 Signals See Table 5-1 for an overview of the reset controller signal properties. For additional information, refer to Section 4. Signal Description. Table 5-1. Reset Controller Signal Properties Name RESET pin RSTOUT pin Alternate Direction Input Hysteresis Input Synchronization Pullup(1) -- I Y Y(2) Y SHOWINT O -- -- -- 1. Pullups are disconnected from pins configured as outputs. 2. RESET is always synchronized except when in low-power stop mode. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Reset Controller Module For More Information On This Product, Go to: www.freescale.com 131 Freescale Semiconductor, Inc. Reset Controller Module 5.6 Memory Map and Registers Freescale Semiconductor, Inc... The reset controller programming model consists of the following registers: * Reset control register (RCR) -- Selects interrupt controller functions * Reset status register (RSR) -- Reflects the state of the last reset source * Reset test register (RTR) -- Used only for factory test Table 5-2. Reset Controller Module Memory Map Address Bits 7-0 Access(1) 0x000c4_0000 Reset control register (RCR) S/U 0x000c4_0001 Reset status register (RSR) S/U 0x000c4_0002 Reset test register (RTR) S/U 0x000c4_0003 Reserved(2) -- 1. S/U = CPU supervisor or user mode access. User mode accesses to supervisor only addresses have no effect and result in a a cycle termination transfer error. 2. Within the specified module memory map, accessing reserved addresses does not generate a bus error exception. Reads of reserved addresses return 0s and writes have no effect. Technical Data 132 MMC2107 - Rev. 2.0 Reset Controller Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Reset Controller Module Memory Map and Registers 5.6.1 Reset Control Register The reset control register (RCR) allows software control for requesting a reset or for independently asserting the external RSTOUT pin. RCR is read/write always. Address: 0x000c4_0000 Bit 7 6 5 4 3 2 1 Bit 0 FRCRSTOUT 0 0 0 0 0 0 SOFTRST 0 0 0 0 0 0 0 0 Freescale Semiconductor, Inc... Read: Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 5-2. Reset Control Register (RCR) SOFTRST -- Software Reset Request Bit The SOFTRST bit allows software to request a reset. Note that the reset caused by setting this bit clears this bit. 1 = Request software reset 0 = No software reset request FRCRSTOUT -- Force RSTOUT Pin Bit The FRCRSTOUT bit allows software to assert or negate the external RSTOUT pin. 1 = Assert the RSTOUT pin. 0 = Do not assert the RSTOUT pin. CAUTION: External logic driving reset configuration data during reset needs to be considered when asserting the RSTOUT pin when setting FRCRSTOUT. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Reset Controller Module For More Information On This Product, Go to: www.freescale.com 133 Freescale Semiconductor, Inc. Reset Controller Module 5.6.2 Reset Status Register The reset status register (RSR) contains a status bit for every reset source. When reset is entered, the cause of the reset condition is latched along with a value of 0 for the other reset sources that were not pending at the time of the reset condition. These values are then reflected in the RSR. One or more status bits may be set at the same time. The cause of any subsequent reset is also recorded in the register, overwriting status from the previous reset condition. Freescale Semiconductor, Inc... RSR can be read at any time. Writing to RSR has no effect. Address: 0x000c4_0001 Read: Bit 7 6 5 4 3 2 1 Bit 0 0 0 SOFT WDR POR EXT LOC LOL 0 0 Write: Reset: Reset dependent = Writes have no effect and the access terminates without a transfer error exception. Figure 5-3. Reset Status Register (RSR) SOFT-- Software Reset Flag SOFT indicates that the last reset was caused by software. 1 = Last reset caused by software 0 = No software reset WDR -- Watchdog Timer Reset Flag WDR indicates that the last reset was caused by a watchdog timer timeout. 1 = Last reset caused by watchdog timer timeout 0 = No watchdog timer timeout reset POR -- Power-On Reset Flag POR indicates that the last reset was caused by a power-on reset. 1 = Last reset caused by power-on reset 0 = Last reset not caused by power-on reset Technical Data 134 MMC2107 - Rev. 2.0 Reset Controller Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Reset Controller Module Memory Map and Registers EXT -- External Reset Flag EXT indicates that the last reset was caused by an external device asserting the external RESET pin. 1 = Last reset state caused by external device asserting the external RESET pin 0 = No external reset Freescale Semiconductor, Inc... LOC -- Loss of Clock Reset Flag LOC indicates that the last reset state was caused by a loss of clock detected by the loss of clock circuit. 1 = Last reset caused by loss of clock 0 = No loss of clock reset LOL -- Loss of Lock Reset Flag LOL indicates that the last reset state was caused by a loss of lock detected by the PLL circuit. 1 = Last reset caused by loss of lock 0 = No loss of lock 5.6.3 Reset Test Register The reset test register (RTR) is used only for factory testing. This register is read-only when not in test mode. Address: 0x000c4_0002 Read: Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 5-4. Reset Test Register (RTR) MMC2107 - Rev. 2.0 MOTOROLA Technical Data Reset Controller Module For More Information On This Product, Go to: www.freescale.com 135 Freescale Semiconductor, Inc. Reset Controller Module 5.7 Functional Description This subsection provides a functional description of the MMC2107 reset controller module. 5.7.1 Reset Sources Freescale Semiconductor, Inc... Table 5-3 defines the sources of reset and the signals driven by the reset controller. Table 5-3. Reset Source Summary Source Type Power on Asynchronous External RESET pin (not stop mode) Synchronous External RESET pin (during stop mode) Asynchronous Watchdog timer Synchronous Loss of clock Asynchronous Loss of lock Asynchronous Software Synchronous To protect data integrity, a synchronous reset source is not acted upon by the reset control logic until the end of the current bus cycle. Reset is then asserted on the next rising edge of the system clock after the cycle is terminated. Whenever the reset control logic must synchronize reset to the end of the bus cycle, the internal bus monitor is automatically enabled regardless of the BME bit setting in the chip configuration register (CCR). Then if the current bus cycle is not terminated normally, the bus monitor terminates the cycle based on the length of time programmed in the BMT field of CCR. Internal single-byte, half-word, or word writes are guaranteed to complete without data corruption when a synchronous reset occurs. External writes, including word writes to 16-bit ports, are also guaranteed to complete. Asynchronous reset sources usually indicate a catastrophic failure. Therefore, the reset control logic does not wait for the current bus cycle to complete. Reset is asserted immediately to the system. Technical Data 136 MMC2107 - Rev. 2.0 Reset Controller Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Reset Controller Module Functional Description 5.7.1.1 Power-On Reset At power-up, the reset controller asserts RSTOUT. RSTOUT continues to be asserted until VDD has reached a minimum acceptable level and, if a PLL clock mode is selected, until the PLL achieves phase lock. Then after approximately another 512 cycles, RSTOUT is negated and the part begins operation. Freescale Semiconductor, Inc... 5.7.1.2 External Reset Asserting the external RESET pin for at least four rising CLKOUT edges causes the external reset request to be recognized and latched. The bus monitor is enabled and the current bus cycle is completed. The reset controller asserts RSTOUT for approximately 512 cycles after the RESET pin is negated and the PLL has acquired lock. The part then exits reset and begins operation. In low-power stop mode, the system clocks are stopped. Asserting the external RESET pin during stop mode causes an external reset to be recognized. 5.7.1.3 Watchdog Timer Reset A watchdog timer timeout causes the watchdog timer reset request to be recognized and latched. The bus monitor is enabled and the current bus cycle is completed. If the RESET pin is negated and the PLL has acquired lock, the reset controller asserts RSTOUT for approximately 512 cycles. Then the part exits reset and begins operation. 5.7.1.4 Loss of Clock Reset This reset condition occurs in PLL clock mode when the LOCRE bit in SYNCR is set and either the PLL reference or the PLL fails. The reset controller asserts RSTOUT for approximately 512 cycles after the PLL has acquired lock. The part then exits reset and begins operation. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Reset Controller Module For More Information On This Product, Go to: www.freescale.com 137 Freescale Semiconductor, Inc. Reset Controller Module 5.7.1.5 Loss of Lock Reset This reset condition occurs in PLL clock mode when the LOLRE bit in SYNCR is set and the PLL loses lock. The reset controller asserts RSTOUT for approximately 512 cycles after the PLL has acquired lock. The part then exits reset and begins operation. Freescale Semiconductor, Inc... 5.7.1.6 Software Reset A software reset occurs when the SOFTRST bit is set. If the RESET pin is negated and the PLL has acquired lock, the reset controller asserts RSTOUT for approximately 512 cycles. Then the part exits reset and begins operation. 5.7.2 Reset Control Flow Figure 5-5 shows the reset logic control flow. In the flow description that follows, there are references in parentheses to the control state box numbers in the figure. All cycle counts given are approximate. 5.7.2.1 Synchronous Reset Requests If either the external RESET pin is asserted by an external device for at least four rising CLKOUT edges (3), or the watchdog timer times out, or software requests a reset, the reset control logic latches the reset request internally and enables the bus monitor (5). When the current bus cycle is completed (6), RSTOUT is asserted (7). The reset control logic waits until the RESET pin is negated (8) and for the PLL to attain lock (9, 9A) before waiting 512 CLKOUT cycles (10). The reset control logic may latch the configuration according to the RCON pin level (11, 11A) before negating RSTOUT (12). If the external RESET pin is asserted by an external device for at least four rising CLKOUT edges during the 512 count (10) or during the wait for PLL lock (9A), the reset flow switches to (8) and waits for the RESET pin to be negated before continuing. Technical Data 138 MMC2107 - Rev. 2.0 Reset Controller Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Reset Controller Module Functional Description 0 1 LOSS OF CLOCK? POR Y N 2 LOSS OF LOCK? Y Freescale Semiconductor, Inc... N 3 4 5 RESET PIN OR WD TIMEOUT OR SW RESET? N Y ASSERT RSTOUT AND LATCH RESET STATUS ENABLE BUS MONITOR 6 BUS CYCLE COMPLETE? N Y 7 ASSERT RSTOUT AND LATCH RESET STATUS 8 N RESET NEGATED? Y 9 PLL MODE? Y 9A N PLL LOCKED? N Y 10 WAIT 512 CLKOUT CYCLES 12 11A 11 NEGATE RSTOUT RCON ASSERTED? Y LATCH CONFIGURATION N Figure 5-5. Reset Control Flow MMC2107 - Rev. 2.0 MOTOROLA Technical Data Reset Controller Module For More Information On This Product, Go to: www.freescale.com 139 Freescale Semiconductor, Inc. Reset Controller Module 5.7.2.2 Internal Reset Request If reset is asserted by an asynchronous internal reset source, such as loss of clock (1) or loss of lock (2), the reset control logic asserts RSTOUT (4). The reset control logic waits for the PLL to attain lock (9, 9A) before waiting 512 CLKOUT cycles (10). Then the reset control logic may latch the configuration according to the RCON pin level (11, 11A) before negating RSTOUT (12). Freescale Semiconductor, Inc... If a loss of lock occurs during the 512 count (10), the reset flow switches to (9A) and waits for the PLL to lock before continuing. 5.7.2.3 Power-On Reset When the reset sequence is initiated by power-on reset (0), the same reset sequence is followed as for the other asynchronous reset sources. 5.7.3 Concurrent Resets This subsection describes the concurrent resets. 5.7.3.1 Reset Flow If a power-on reset condition is detected during any reset sequence, the power-on reset sequence starts immediately (0). If the external RESET pin is asserted for at least four rising CLKOUT edges while waiting for PLL lock or the 512 cycles, the external reset is recognized. Reset processing switches to wait for the external RESET pin to negate (8). If a loss of clock or loss of lock condition is detected while waiting for the current bus cycle to complete (5, 6) for an external reset request, the cycle is terminated. The reset status bits are latched (7) and reset processing waits for the external RESET pin to negate (8). If a loss of clock or loss of lock condition is detected during the 512-cycle wait, the reset sequence continues after a PLL lock (9, 9A). Technical Data 140 MMC2107 - Rev. 2.0 Reset Controller Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Reset Controller Module Interrupts 5.7.3.2 Reset Status Flags For a power-on reset, the POR bit in RSR is set, and the SOFT, WDR, EXT, LOC, and LOL bits are cleared even if another type of reset condition is detected during the reset sequence for the POR. Freescale Semiconductor, Inc... If a loss of clock or loss of lock condition is detected while waiting for the current bus cycle to complete (5, 6) for an external reset request, the EXT bit along with the LOC and/or LOL bits are set. 5.8 Interrupts The reset controller does not generate interrupt requests. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Reset Controller Module For More Information On This Product, Go to: www.freescale.com 141 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Reset Controller Module Technical Data 142 MMC2107 - Rev. 2.0 Reset Controller Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 6. M*CORE M210 Central Processor Unit (CPU) Freescale Semiconductor, Inc... 6.1 Contents 6.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 6.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 6.4 Microarchitecture Summary . . . . . . . . . . . . . . . . . . . . . . . . . . 145 6.5 Programming Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 6.6 Data Format Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 6.7 Operand Addressing Capabilities . . . . . . . . . . . . . . . . . . . . . . 150 6.8 Instruction Set Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 6.2 Introduction The M*CORE M210 central processor unit (CPU) architecture is one of the most compact, full 32-bit core implementations available. The pipelined reduced instruction set computer (RISC) execution unit uses 16-bit instructions to achieve maximum speed and code efficiency, while conserving on-chip memory resources. The instruction set is designed to support high-level language implementation. A non-intrusive resident debugging system supports product development and in-situ testing. The M*CORE technology library also encompasses a full complement of on-chip peripheral modules designed specifically for embedded control applications. Total system power consumption is determined by all the system components, rather than the processor core alone. In particular, memory power consumption (both on-chip and external) is a dominant factor in total power consumption of the core plus memory subsystem. With this in mind, the M*CORE instruction set architecture trades absolute performance capability for reduced total energy consumption. This is accomplished while maintaining an acceptably high level of performance at a given clock frequency. MMC2107 - Rev. 2.0 MOTOROLA Technical Data M*CORE M210 Central Processor Unit (CPU) For More Information On This Product, Go to: www.freescale.com 143 Freescale Semiconductor, Inc. M*CORE M210 Central Processor Unit (CPU) Freescale Semiconductor, Inc... The streamlined execution engine uses many of the same performance enhancements and implementation techniques incorporated in desktop RISC processors. A strictly defined load/store architecture minimizes control complexity. Use of a fixed, 16-bit instruction encoding significantly lowers the memory bandwidth needed to sustain a high rate of instruction execution, and careful selection of the instruction set allows the code density and overall memory efficiency of the M*CORE architecture to surpass those of complex instruction set computer (CISC) architectures. These factors reduce system energy consumption significantly, and the fully static M*CORE design uses other techniques to reduce it even more. The core uses dynamic clock management to automatically power-down internal functions that are not in use on a clock-by-clock basis. It also incorporates three power-conservation operating modes, which are invoked via dedicated instructions. 6.3 Features The main features of the M*CORE are: * 32-bit load/store RISC architecture * Fixed 16-bit instruction length * 16 entry, 32-bit general-purpose register file * Efficient 4-stage execution pipeline, hidden from application software * Single-cycle execution for most instructions, 2-cycle branches and memory accesses * Support for byte/half-word/word memory access * Fast interrupt support, with 16 entry user-controlled alternate register file * Vectored and autovectored interrupt support * On-chip emulation support * Full static design for minimal power consumption Technical Data 144 MMC2107 - Rev. 2.0 M*CORE M210 Central Processor Unit (CPU) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. M*CORE M210 Central Processor Unit (CPU) Microarchitecture Summary 6.4 Microarchitecture Summary Figure 6-1 is a block diagram of the M*CORE processor. Freescale Semiconductor, Inc... The processor utilizes a 4-stage pipeline for instruction execution. The instruction fetch, instruction decode/register file read, execute, and register file writeback stages operate in an overlapped fashion, allowing single clock instruction execution for most instructions. The execution unit consists of a 32-bit arithmetic/logic unit, a 32-bit barrel shifter, a find-first-one unit, result feed-forward hardware, and miscellaneous support hardware for multiplication, division, and multiple-register loads and stores. DATA CALCULATION GENERAL-PURPOSE REGISTER FILE 32 BITS X 16 ADDRESS GENERATION ALTERNATE REGISTER FILE 32 BITS X 16 CONTROL REGISTER FILE 32 BITS X 13 Y PORT X PORT ADDRESS MUX ADDRESS BUS IMMEDIATE MUX PC INCREMENT SCALE BRANCH ADDER BARREL SHIFTER MULTIPLIER DIVIDER SIGN EXT. MUX MUX INSTRUCTION PIPELINE ADDER/LOGICAL PRIORITY ENCODER/ ZERO DETECT RESULT MUX INSTRUCTION DECODE WRITEBACK BUS H/W ACCELERATOR INTERFACE BUS DATA BUS Figure 6-1. M*CORE Processor Block Diagram MMC2107 - Rev. 2.0 MOTOROLA Technical Data M*CORE M210 Central Processor Unit (CPU) For More Information On This Product, Go to: www.freescale.com 145 Freescale Semiconductor, Inc. M*CORE M210 Central Processor Unit (CPU) Arithmetic and logical operations are executed in a single cycle. Multiplication is implemented with a 2-bit per clock, overlapped-scan, modified Booth algorithm with early-out capability, to reduce execution time for operations with small multipliers. Divide is implemented with a 1-bit per clock early-in algorithm. The find-first-one unit operates in a single clock cycle. Freescale Semiconductor, Inc... The program counter unit incorporates a dedicated branch address adder to minimize delays during change of flow operations. Branch target addresses are calculated in parallel with branch instruction decode. Taken branches and jumps require only two clocks; branches which are not taken execute in a single clock. Memory load and store operations are provided for 8-bit (byte), 16-bit (half-word), and 32-bit (word) data, with automatic zero extension for byte and half-word load operations. These instructions can execute in as few as two clock cycles. Load and store multiple register instructions allow low overhead context save and restore operations. These instructions can execute in (N+1) clock cycles, where N is the number of registers to transfer. A condition code/carry (C) bit is provided for condition testing and for use in implementing arithmetic and logical operations with operands/results greater than 32 bits. The C bit is typically set by explicit test/comparison operations, not as a side-effect of normal instruction operation. Exceptions to this rule occur for specialized operations where it is desirable to combine condition setting with actual computation. The processor uses autovectors for both normal and fast interrupt requests. Fast interrupts take precedence over normal interrupts. Both types have dedicated exception shadow registers. For service requests of either kind, an automatic vector is generated when the request is made. Technical Data 146 MMC2107 - Rev. 2.0 M*CORE M210 Central Processor Unit (CPU) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. M*CORE M210 Central Processor Unit (CPU) Programming Model 6.5 Programming Model Figure 6-2 shows the M*CORE programming model. The model is defined differently for supervisor and user privilege modes. By convention, in both modes R15 serves as the link register for subroutine calls. R0 is typically used as stack pointer. R0 R1 Freescale Semiconductor, Inc... ALTERNATE FILE R0' R0 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R12 R13 R14 R1 PSR CR0 R2 VBR CR1 R3 EPSR CR2 R4 FPSR CR3 R5 EPC CR4 R6 FPC CR5 R7 SS0 CR6 R8 SS1 CR7 R9 SS2 CR8 R10 SS3 CR9 R11 SS4 CR10 R12 GCR CR11 R13 GSR CR12 R14 R15 R15 PC PC C C USER PROGRAMMER'S MODEL * BIT 0 OF PSR SUPERVISOR PROGRAMMER'S MODEL Figure 6-2. Programming Model The user programming model consists of 16 general-purpose 32-bit registers (R[15:0]), the 32-bit PC, and the C bit. The C bit is implemented as bit 0 of the processor status register (PSR) and is the only portion of the PSR accessible in the user model. MMC2107 - Rev. 2.0 MOTOROLA Technical Data M*CORE M210 Central Processor Unit (CPU) For More Information On This Product, Go to: www.freescale.com 147 Freescale Semiconductor, Inc. M*CORE M210 Central Processor Unit (CPU) The supervisor programming model consists of the user model plus 16 additional 32-bit general-purpose registers (R[15:0]', or the alternate file), the entire PSR, and a set of status/control registers (CR[12:0]). Setting the S bit in the PSR enables supervisor mode operation. The alternate file allows very low overhead context switching for real-time event handling. While the alternate file is enabled, general-purpose operands are accessed from it. Freescale Semiconductor, Inc... The vector base register (VBR) determines the base address of the exception vector table. Exception shadow registers EPC and EPSR are used to save the states of the program counter and PSR, respectively, when an exception occurs. Shadow registers FPC and FPSR save the states of the program counter and PSR, respectively, when an exception occurs. Scratch registers (SS[4:0]) are used to handle exception events. The global control (GCR) and status (GSR) registers can be used for a variety of system monitoring tasks. The supervisor programming model includes the PSR, which contains operation control and status information. In addition, a set of exception shadow registers is provided to save the state of the PSR and the program counter at the time an exception occurs. A separate set of shadow registers is provided for fast interrupt support to minimize context saving overhead. Five scratch registers are provided for supervisor software use in handling exception events. A single register is provided to alter the base address of the exception vector table. Two registers are provided for global control and status. Technical Data 148 MMC2107 - Rev. 2.0 M*CORE M210 Central Processor Unit (CPU) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. M*CORE M210 Central Processor Unit (CPU) Data Format Summary 6.6 Data Format Summary The operand data formats supported by the integer unit are standard two's-complement data formats. The operand size for each instruction is either explicitly encoded in the instruction (load/store instructions) or implicitly defined by the instruction operation (index operations, byte extraction). Typically, instructions operate on all 32 bits of the source operand(s) and generate a 32-bit result. Freescale Semiconductor, Inc... Memory is viewed from a big-endian byte ordering perspective. The most significant byte (byte 0) of word 0 is located at address 0. Bits are numbered within a word starting with bit 31 as the most significant bit. 31 0 BYTE 0 BYTE 1 BYTE 2 BYTE 3 WORD AT 0X0000 000 0 BYTE 4 BYTE 5 BYTE 6 BYTE 7 WORD AT 0X0000 000 4 BYTE 8 BYTE 9 BYTE A BYTE B WORD AT 0X0000 000 8 BYTE C BYTE D BYTE E BYTE F WORD AT 0X0000 000 C Figure 6-3. Data Organization in Memory 31 87 S S S S S S S S S S S S S S S S S S S S S SSSS 31 0 BYTE 87 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 31 BYTE 16 15 S S S S S S S S S S S S S S S S 31 SIGNED BYTE UNSIGNED BYTE 0 S SIGNED HALF-WORD HALF-WORD 16 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 UNSIGNED HALF-WORD HALF-WORD 31 0 BYTE 0 BYTE 1 BYTE 2 BYTE 3 WORD Figure 6-4. Data Organization in Registers MMC2107 - Rev. 2.0 MOTOROLA Technical Data M*CORE M210 Central Processor Unit (CPU) For More Information On This Product, Go to: www.freescale.com 149 Freescale Semiconductor, Inc. M*CORE M210 Central Processor Unit (CPU) 6.7 Operand Addressing Capabilities Freescale Semiconductor, Inc... M*CORE accesses all memory operands through load and store instructions, transferring data between the general-purpose registers and memory. Register-plus-four-bit scaled displacement addressing mode is used for load and store instructions addressing byte, half-word, and word data. Load and store multiple instructions allow a subset of the 16 general-purpose registers to be transferred to or from a base address pointed to by register R0 (the default stack pointer by convention). Load and store register quadrant instructions use register indirect addressing to transfer a register quadrant to or from memory. 6.8 Instruction Set Overview The instruction set is tailored to support high-level languages and is optimized for those instructions most commonly executed. A standard set of arithmetic and logical instructions is provided, as well as instruction support for bit operations, byte extraction, data movement, control flow modification, and a small set of conditionally executed instructions which can be useful in eliminating short conditional branches. Table 6-1 is an alphabetized listing of the M*CORE instruction set. Refer to the M*CORE Reference Manual (Motorola document order number MCORERM/AD) for more details on instruction operation. Table 6-1. M*CORE Instruction Set (Sheet 1 of 3) Mnemonic ABS ADDC ADDI ADDU AND ANDI ANDN ASR ASRC Description Absolute Value Add with C Bit Add Immediate Add Unsigned Logical AND Logical AND Immediate AND NOT Arithmetic Shift Right Arithmetic Shift Right, Update C Bit Technical Data 150 MMC2107 - Rev. 2.0 M*CORE M210 Central Processor Unit (CPU) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. M*CORE M210 Central Processor Unit (CPU) Instruction Set Overview Table 6-1. M*CORE Instruction Set (Sheet 2 of 3) Freescale Semiconductor, Inc... Mnemonic Description BCLRI BF BGENI BGENR BKPT BMASKI BR BREV BSETI BSR BT BTSTI Bit Clear Immediate Branch on Condition False Bit Generate Immediate Bit Generate Register Breakpoint Bit Mask Immediate Branch Bit Reverse Bit Set Immediate Branch to Subroutine Branch on Condition True Bit Test Immediate CLRF CLRT CMPHS CMPLT CMPLTI CMPNE CMPNEI Clear Register on Condition False Clear Register on Condition True Compare Higher or Same Compare Less Than Compare Less Than Immediate Compare Not Equal Compare Not Equal Immediate DECF DECGT DECLT DECNE DECT DIVS DIVU DOZE Decrement on Condition False Decrement Register and Set Condition if Result Greater Than Zero Decrement Register and Set Condition if Result Less Than Zero Decrement Register and Set Condition if Result Not Equal to Zero Decrement on Condition True Divide Signed Integer Divide Unsigned Integer Doze FF1 Find First One INCF INCT IXH IXW Increment on Condition False Increment on Condition True Index Half-Word Index Word JMP JMPI JSR JSRI Jump Jump Indirect Jump to Subroutine Jump to Subroutine Indirect LD.[BHW] LDM LDQ LOOPT LRW LSL, LSR LSLC, LSRC LSLI, LSRI Load Load Multiple Registers Load Register Quadrant Decrement with C-Bit Update and Branch if Condition True Load Relative Word Logical Shift Left and Right Logical Shift Left and Right, Update C Bit Logical Shift Left and Right by Immediate MMC2107 - Rev. 2.0 MOTOROLA Technical Data M*CORE M210 Central Processor Unit (CPU) For More Information On This Product, Go to: www.freescale.com 151 Freescale Semiconductor, Inc. M*CORE M210 Central Processor Unit (CPU) Table 6-1. M*CORE Instruction Set (Sheet 3 of 3) Freescale Semiconductor, Inc... Mnemonic Description MFCR MOV MOVI MOVF MOVT MTCR MULT MVC MVCV Move from Control Register Move Move Immediate Move on Condition False Move on Condition True Move to Control Register Multiply Move C Bit to Register Move Inverted C Bit to Register NOT Logical Complement OR Logical Inclusive-OR ROTLI RSUB RSUBI RTE RFI Rotate Left by Immediate Reverse Subtract Reverse Subtract Immediate Return from Exception Return from Interrupt SEXTB SEXTH ST.[BHW] STM STQ STOP SUBC SUBU SUBI SYNC Sign-Extend Byte Sign-Extend Half-Word Store Store Multiple Registers Store Register Quadrant Stop Subtract with C Bit Subtract Subtract Immediate Synchronize TRAP TST TSTNBZ Trap Test Operands Test for No Byte Equal Zero WAIT Wait XOR XSR XTRB0 XTRB1 XTRB2 XTRB3 Exclusive OR Extended Shift Right Extract Byte 0 Extract Byte 1 Extract Byte 2 Extract Byte 3 ZEXTB ZEXTH Zero-Extend Byte Zero-Extend Half-Word Technical Data 152 MMC2107 - Rev. 2.0 M*CORE M210 Central Processor Unit (CPU) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 7. Interrupt Controller Module Freescale Semiconductor, Inc... 7.1 Contents 7.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 7.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 7.4 Low-Power Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 154 7.5 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 7.6 External Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 7.7 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 155 7.7.1 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 7.7.2 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157 7.7.2.1 Interrupt Control Register. . . . . . . . . . . . . . . . . . . . . . . . 157 7.7.2.2 Interrupt Status Register . . . . . . . . . . . . . . . . . . . . . . . . 159 7.7.2.3 Interrupt Force Registers . . . . . . . . . . . . . . . . . . . . . . . . 160 7.7.2.4 Interrupt Pending Register . . . . . . . . . . . . . . . . . . . . . . .162 7.7.2.5 Normal Interrupt Enable Register. . . . . . . . . . . . . . . . . . 163 7.7.2.6 Normal Interrupt Pending Register. . . . . . . . . . . . . . . . . 164 7.7.2.7 Fast Interrupt Enable Register . . . . . . . . . . . . . . . . . . . . 165 7.7.2.8 Fast Interrupt Pending Register . . . . . . . . . . . . . . . . . . .166 7.7.2.9 Priority Level Select Registers . . . . . . . . . . . . . . . . . . . . 167 7.8 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 7.8.1 Interrupt Sources and Prioritization . . . . . . . . . . . . . . . . . .168 7.8.2 Fast and Normal Interrupt Requests . . . . . . . . . . . . . . . . . 168 7.8.3 Autovectored and Vectored Interrupt Requests . . . . . . . . .169 7.8.4 Interrupt Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 7.8.4.1 M*CORE Processor Configuration . . . . . . . . . . . . . . . . . 171 7.8.4.2 Interrupt Controller Configuration. . . . . . . . . . . . . . . . . . 171 7.8.4.3 Interrupt Source Configuration . . . . . . . . . . . . . . . . . . . . 172 7.8.5 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Interrupt Controller Module For More Information On This Product, Go to: www.freescale.com 153 Freescale Semiconductor, Inc. Interrupt Controller Module 7.2 Introduction The interrupt controller collects requests from multiple interrupt sources and provides an interface to the processor core interrupt logic. 7.3 Features Freescale Semiconductor, Inc... Features of the interrupt controller module include: * Up to 40 interrupt sources * 32 unique programmable priority levels for each interrupt source * Independent enable/disable of pending interrupts based on priority level * Select normal or fast interrupt request for each priority level * Fast interrupt requests always have priority over normal interrupts * Ability to mask interrupts at and below a defined priority level * Ability to select between autovectored or vectored interrupt requests * Vectored interrupts generated based on priority level * Ability to generate a separate vector number for normal and fast interrupts * Ability for software to self-schedule interrupts * Software visibility of pending interrupts and interrupt signals to core * Asynchronous operation to support wakeup from low-power modes 7.4 Low-Power Mode Operation The interrupt controller is not affected by any low-power modes. All logic between the input sources and generating the raw interrupt to the M*CORE processor is combinational. This allows the M*CORE processor to wake up during low-power stop mode when all system clocks are stopped. Technical Data 154 MMC2107 - Rev. 2.0 Interrupt Controller Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Interrupt Controller Module Block Diagram 7.5 Block Diagram F I E R I F R F I P R M 32-TO-5 U PRIORITY X 32 ENCODER 5 & FVE INTERRUPT SOURCES Freescale Semiconductor, Inc... OR 40 & 32 40 PRIORITY LEVEL SELECT I P R FMASK & 32 NMASK & OR 32 & S Y N C 32 N I E R MASK ICR N I P R 5 NORMAL AND FAST INTERRUPTS ISR AE 32 DECODE VECTOR NUMBER OR 32 40 x 5 BITS PLSR PLSR PLSR PLSR S Y N C 32 AUTOVECTOR SELECT NMASK & ME 32 MFI & FMASK Figure 7-1. Interrupt Controller Block Diagram 7.6 External Signals No interrupt controller signals connect off-chip. 7.7 Memory Map and Registers This subsection describes the memory map (see Table 7-1) and registers. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Interrupt Controller Module For More Information On This Product, Go to: www.freescale.com 155 Freescale Semiconductor, Inc. Interrupt Controller Module 7.7.1 Memory Map Table 7-1. Interrupt Controller Module Memory Map Address Freescale Semiconductor, Inc... 0x00c5_0000 Bits 31-24 Bits 23-16 Interrupt control register (ICR) Bits 15-8 Bits 7-0 Interrupt status register (ISR) Access(1) S/U 0x00c5_0004 Interrupt force register high (IFRH) S/U 0x00c5_0008 IInterrupt force register low (IFRL) S/U 0x00c5_000c Interrupt pending register (IPR) S/U 0x00c5_0010 Normal interrupt enable register (NIER) S/U 0x00c5_0014 Normal interrupt pending register (NIPR) S/U 0x00c5_0018 Fast interrupt enable register (FIER) S/U 0x00c5_001c Fast interrupt pending register (FIPR) S/U 0x00c5_0020 through 0x00c5_003c Unimplemented(2) -- Priority level select registers (PLSR0-PLSR39) 0x00c5_0040 PLSR0 PLSR1 PLSR2 PLSR3 S 0x00c5_0044 PLSR4 PLSR5 PLSR6 PLSR7 S 0x00c5_0048 PLSR8 PLSR9 PLSR10 PLSR11 S 0x00c5_004c PLSR12 PLSR13 PLSR14 PLSR15 S 0x00c5_0050 PLSR16 PLSR17 PLSR18 PLSR19 S 0x00c5_0054 PLSR20 PLSR21 PLSR22 PLSR23 S 0x00c5_0058 PLSR24 PLSR25 PLSR26 PLSR27 S 0x00c5_005c PLSR28 PLSR29 PLSR30 PLSR31 S 0x00c5_0060 PLSR32 PLSR33 PLSR34 PLSR35 S 0x00c5_0064 PLSR36 PLSR37 PLSR38 PLSR39 S 0x00c5_0068 through 0x00c5_007c Unimplemented(2) -- 1. S = CPU supervisor mode access only. S/U = CPU supervisor or user mode access. User mode accesses to supervisor only addresses have no effect and result in a cycle termination transfer error. 2. Accesses to unimplemented address locations have no effect and result in a cycle termination transfer error. Technical Data 156 MMC2107 - Rev. 2.0 Interrupt Controller Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Interrupt Controller Module Memory Map and Registers 7.7.2 Registers This subsection contains a description of the interrupt controller module registers. 7.7.2.1 Interrupt Control Register Freescale Semiconductor, Inc... The 16-bit interrupt control register (ICR) selects whether interrupt requests are autovectored or vectored, and if vectored, whether fast interrupts generate a different vector number than normal interrupts. This register also controls the masking functions. Address: 0x00c5_0000 and 0x00c5_0001 Bit 15 14 13 12 11 10 9 Bit 8 AE FVE ME MFI 0 0 0 0 1 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 MASK4 MASK3 MASK2 MASK1 MASK0 0 0 0 0 0 Read: Write: Reset: Read: Write: Reset: 0 0 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 7-2. Interrupt Control Register (ICR) AE -- Autovector Enable Bit The read/write AE bit enables autovectored interrupt requests. Reset sets AE. 1 = Autovectored interrupt requests 0 = Vectored interrupt requests FVE -- Fast Vector Enable Bit The read/write FVE bit enables fast vectored interrupt requests to have vector numbers separate from normal vectored interrupt requests. Reset clears FVE. 1 = Unique vector numbers for fast vectored interrupt requests 0 = Same vector number for fast and normal vectored interrupt requests MMC2107 - Rev. 2.0 MOTOROLA Technical Data Interrupt Controller Module For More Information On This Product, Go to: www.freescale.com 157 Freescale Semiconductor, Inc. Interrupt Controller Module ME -- Mask Enable Bit The read/write ME bit enables interrupt masking. Reset clears ME. 1 = Interrupt masking enabled 0 = Interrupt masking disabled MFI -- Mask Fast Interrupts Bit Freescale Semiconductor, Inc... The read/write MFI bit enables masking of fast interrupt requests. Reset clears MFI. 1 = Fast interrupt requests masked by MASK value. All normal interrupt requests are masked. 0 = Fast interrupt requests are not masked regardless of the MASK value. The MASK only applies to normal interrupts. Reset clears MFI. MASK[4:0] -- Interrupt Mask Field The read/write MASK[4:0] field determines which interrupt priority levels are masked. When the ME bit is set, all pending interrupt requests at priority levels at and below the current MASK value are masked. To mask all normal interrupts without masking any fast interrupts, set the MASK value to 31 with the MFI bit cleared. See Table 7-2. Reset clears MASK[4:0]. Table 7-2. MASK Encoding MASK[4:0] Decimal Binary Masked Priority Levels 0 00000 0 1 00001 1-0 2 00010 2-0 3 00011 3-0 * * * * * * * * * 31 11111 31-0 Technical Data 158 MMC2107 - Rev. 2.0 Interrupt Controller Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Interrupt Controller Module Memory Map and Registers 7.7.2.2 Interrupt Status Register The 16-bit, read-only interrupt status register (ISR) reflects the state of the interrupt controller outputs to the M*CORE processor. Writes to this register have no effect and are terminated normally. Address: 0x00c5_0002 and 0x00c5_0003 Read: Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 INT FINT 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 VEC6 VEC5 VEC4 VEC3 VEC2 VEC1 VEC0 0 0 0 0 0 0 0 0 Freescale Semiconductor, Inc... Write: Reset: Read: Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 7-3. Interrupt Status Register (ISR) INT -- Normal Interrupt Request Flag The read-only INT flag indicates whether the normal interrupt request signal to the M*CORE processor is asserted or negated. Reset clears INT. 1 = Normal interrupt request asserted 0 = Normal interrupt request negated FINT -- Fast Interrupt Request Flag The read-only FINT flag indicates whether the fast interrupt request signal to the M*CORE processor is asserted or negated. Reset clears FINT. 1 = Fast interrupt request asserted 0 = Fast interrupt request negated VEC[6:0] -- Interrupt Vector Number Field The read-only VEC[6:0] field reflects the state of the 7-bit interrupt vector number. Reset clears VEC[6:0]. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Interrupt Controller Module For More Information On This Product, Go to: www.freescale.com 159 Freescale Semiconductor, Inc. Interrupt Controller Module 7.7.2.3 Interrupt Force Registers The two 32-bit read/write interrupt force registers (IFRH and IFRL) individually force interrupt source requests. Address: 0x00c5_0004 through 0x00c5_0007 Read: Bit 31 30 29 28 27 26 25 Bit 24 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 23 22 21 20 19 18 17 Bit 16 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 IF39 IF38 IF37 IF36 IF35 IF34 IF33 IF32 0 0 0 0 0 0 0 0 Write: Freescale Semiconductor, Inc... Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 7-4. Interrupt Force Register High (IFRH) Technical Data 160 MMC2107 - Rev. 2.0 Interrupt Controller Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Interrupt Controller Module Memory Map and Registers Address: 0x00c5_0008 through 0x00c5_000b Bit 31 30 29 28 27 26 25 Bit 24 IF31 IF30 IF29 IF28 IF27 IF26 IF25 IF24 0 0 0 0 0 0 0 0 Bit 23 22 21 20 19 18 17 Bit 16 IF23 IF22 IF21 IF20 IF19 IF18 IF17 IF16 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 IF15 IF14 IF13 IF12 IF11 IF10 IF9 IF8 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 IF7 IF6 IF5 IF4 IF3 IF2 IF1 IF0 0 0 0 0 0 0 0 0 Read: Write: Reset: Read: Freescale Semiconductor, Inc... Write: Reset: Read: Write: Reset: Read: Write: Reset: Figure 7-5. Interrupt Force Register Low (IFRL) IF[39:0] -- Interrupt Force Field This read/write field forces interrupt requests at the corresponding source numbers. IFRH and IFRL allow software generation of interrupt requests for functional or debug purposes. Writing 0 to an IF bit negates the interrupt request. Reset clears the IF[39:0] field. 1 = Force interrupt request 0 = Interrupt source not forced MMC2107 - Rev. 2.0 MOTOROLA Technical Data Interrupt Controller Module For More Information On This Product, Go to: www.freescale.com 161 Freescale Semiconductor, Inc. Interrupt Controller Module 7.7.2.4 Interrupt Pending Register The 32-bit, read-only interrupt pending register (IPR) reflects any currently pending interrupts which are assigned to each priority level. Writes to this register have no effect and are terminated normally. Address: 0x00c5_000c through 0x00c5_000f Read: Bit 31 30 29 28 27 26 25 Bit 24 IP31 IP30 IP29 IP28 IP27 IP26 IP25 IP24 0 0 0 0 0 0 0 0 Bit 23 22 21 20 19 18 17 Bit 16 IP23 IP22 IP21 IP20 IP19 IP18 IP17 IP16 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 IP15 IP14 IP13 IP12 IP11 IP10 IP9 IP8 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 IP7 IP6 IP5 IP4 IP3 IP2 IP1 IP0 0 0 0 0 0 0 0 0 Freescale Semiconductor, Inc... Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 7-6. Interrupt Pending Register (IPR) IP[31:0] -- Interrupt Pending Field A read-only IPx bit is set when at least one interrupt request is asserted at priority level x. Reset clears IP[31:0]. 1 = At least one interrupt request asserted at priority level x 0 = All interrupt requests at level x negated Technical Data 162 MMC2107 - Rev. 2.0 Interrupt Controller Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Interrupt Controller Module Memory Map and Registers 7.7.2.5 Normal Interrupt Enable Register The read/write, 32-bit normal interrupt enable register (NIER) individually enables any current pending interrupts which are assigned to each priority level as a normal interrupt source. Enabling an interrupt source which has an asserted request causes that request to become pending, and a request to the M*CORE processor is asserted if not already outstanding. Freescale Semiconductor, Inc... Address: 0x00c5_0010 through 0x00c5_0013 Bit 31 30 29 28 27 26 25 Bit 24 NIE31 NIE30 NIE29 NIE28 NIE27 NIE26 NIE25 NIE24 0 0 0 0 0 0 0 0 Bit 23 22 21 20 19 18 17 Bit 16 NIE23 NIE22 NIE21 NIE20 NIE19 NIE18 NIE17 NIE16 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 NIE15 NIE14 NIE13 NIE12 NIE11 NIE10 NIE9 NIE8 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 NIE7 NIE6 NIE5 NIE4 NIE3 NIE2 NIE1 NIE0 0 0 0 0 0 0 0 0 Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: Figure 7-7. Normal Interrupt Enable Register (NIER) NIE[31:0] -- Normal Interrupt Enable Field The read/write NIE[31:0] field enables interrupt requests from sources at the corresponding priority level as normal interrupt requests. Reset clears NIE[31:0]. 1 = Normal interrupt request enabled 0 = Normal interrupt request disabled MMC2107 - Rev. 2.0 MOTOROLA Technical Data Interrupt Controller Module For More Information On This Product, Go to: www.freescale.com 163 Freescale Semiconductor, Inc. Interrupt Controller Module 7.7.2.6 Normal Interrupt Pending Register The read-only, 32-bit normal interrupt pending register (NIPR) reflects any currently pending normal interrupts which are assigned to each priority level. Writes to this register have no effect and are terminated normally. Address: 0x00c5_0014 through 0x00c5_0017 Freescale Semiconductor, Inc... Read: Bit 31 30 29 28 27 26 25 Bit 24 NIP31 NIP30 NIP29 NIP28 NIP27 NIP26 NIP25 NIP24 0 0 0 0 0 0 0 0 Bit 23 22 21 20 19 18 17 Bit 16 NIP23 NIP22 NIP21 NIP20 NIP19 NIP18 NIP17 NIP16 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 NIP15 NIP14 NIP13 NIP12 NIP11 NIP10 NIP9 NIP8 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 NIP7 NIP6 NIP5 NIP4 NIP3 NIP2 NIP1 NIP0 0 0 0 0 0 0 0 0 Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 7-8. Normal Interrupt Pending Register (NIPR) NIP[31:0] -- Normal Interrupt Pending Field A read-only NIPx bit is set when at least one normal interrupt request is asserted at priority level x. Reset clears NIP[31:0]. 1 = At least one normal interrupt request asserted at priority level x 0 = All normal interrupt requests at priority level x negated Technical Data 164 MMC2107 - Rev. 2.0 Interrupt Controller Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Interrupt Controller Module Memory Map and Registers 7.7.2.7 Fast Interrupt Enable Register The read/write, 32-bit fast interrupt enable register (FIER) enables any current pending interrupts which are assigned at each priority level as a fast interrupt source. Enabling an interrupt source which has an asserted request causes that interrupt to become pending, and a request to the M*CORE processor is asserted if not already outstanding. Freescale Semiconductor, Inc... Address: 0x00c5_0018 through 0x00c5_001b Bit 31 30 29 28 27 26 25 Bit 24 FIE31 FIE30 FIE29 FIE28 FIE27 FIE26 FIE25 FIE24 0 0 0 0 0 0 0 0 Bit 23 22 21 20 19 18 17 Bit 16 FIE23 FIE22 FIE21 FIE20 FIE19 FIE18 FIE17 FIE16 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 FIE15 FIE14 FIE13 FIE12 FIE11 FIE10 FIE9 FIE8 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 FIE7 FIE6 FIE5 FIE4 FIE3 FIE2 FIE1 FIE0 0 0 0 0 0 0 0 0 Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: Figure 7-9. Fast Interrupt Enable Register (FIER) FIE[31:0] -- Fast Interrupt Enable Field The read/write FIE[31:0] field enables interrupt requests from sources at the corresponding priority level as fast interrupts. Reset clears FIE[31:0]. 1 = Fast interrupt enabled 0 = Fast interrupt disabled MMC2107 - Rev. 2.0 MOTOROLA Technical Data Interrupt Controller Module For More Information On This Product, Go to: www.freescale.com 165 Freescale Semiconductor, Inc. Interrupt Controller Module 7.7.2.8 Fast Interrupt Pending Register The read-only, 32-bit fast interrupt pending register (FIPR) reflects any currently pending fast interrupts which are assigned to each priority level. Writes to this register have no effect and are terminated normally. Address: 0x00c5_001c through 0x00c5_001f Read: Bit 31 30 29 28 27 26 25 Bit 24 FIP31 FIP30 FIP29 FIP28 FIP27 FIP26 FIP25 FIP24 0 0 0 0 0 0 0 0 Bit 23 22 21 20 19 18 17 Bit 16 FIP23 FIP22 FIP21 FIP20 FIP19 FIP18 FIP17 FIP16 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 FIP15 FIP14 FIP13 FIP12 FIP11 FIP10 FIP9 FIP8 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 FIP7 FIP6 FIP5 FIP4 FIP3 FIP2 FIP1 FIP0 0 0 0 0 0 0 0 0 Freescale Semiconductor, Inc... Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 7-10. Fast Interrupt Pending Register (FIPR) FIP[31:0] -- Fast Interrupt Pending Field A read-only FIP[x] bit is set when at least one interrupt request at priority level x is pending and enabled as a fast interrupt. Reset clears FIP[31:0]. 1 = At least one fast interrupt request asserted at priority level x 0 = Any fast interrupt requests at priority level x negated Technical Data 166 MMC2107 - Rev. 2.0 Interrupt Controller Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Interrupt Controller Module Functional Description 7.7.2.9 Priority Level Select Registers There are 40 read/write, 8-bit priority level select registers PLSR0-PLSR39, one for every interrupt source. The PLSRx register assigns a priority level to interrupt source x. Address: 0x00c5_0040 through 0x00c5_0067 Freescale Semiconductor, Inc... Read: Bit 7 6 5 0 0 0 4 3 2 1 Bit 0 PLS4 PLS3 PLS2 PLS1 PLS0 0 0 0 0 0 Write: Reset: 0 0 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 7-11. Priority Level Select Registers (PLSR0-PLSR39) PLS[4:0] -- Priority Level Select Field The PLS[4:0] field assigns a priority level from 0 to 31 to the corresponding interrupt source. Reset clears PLS[4:0]. Table 7-3. Priority Select Encoding PLS[4:0] Priority Level Vector Number 00000 0 (lowest) 00000 00001-11110 1-30 00001-11110 11111 31 (highest) 11111 7.8 Functional Description The interrupt controller collects interrupt requests from multiple interrupt sources and provides an interface to the processor core interrupt logic. Interrupt controller functions include: * Interrupt source prioritization * Fast and normal interrupt requests * Autovectored and vectored interrupt requests * Interrupt configuration MMC2107 - Rev. 2.0 MOTOROLA Technical Data Interrupt Controller Module For More Information On This Product, Go to: www.freescale.com 167 Freescale Semiconductor, Inc. Interrupt Controller Module Freescale Semiconductor, Inc... 7.8.1 Interrupt Sources and Prioritization Each interrupt source in the system sends a unique signal to the interrupt controller. Up to 40 interrupt sources are supported. Each interrupt source can be programmed to one of 32 priority levels using PLSR in the interrupt controller. The highest priority level is 31 and lowest priority level is 0. By default, each interrupt source is assigned to the priority level 0. Each interrupt source is associated with a 5-bit priority level select value that selects one of 32 priority levels. The interrupt controller uses the priority levels as the basis for the generation of all interrupt signals to the M*CORE processor. Interrupt requests may be forced by software by writing to IFRH and IFRL. Each bit of IFRH and IFRL is logically ORed with the corresponding interrupt source signal before the priority level select logic. To negate the forced interrupt request, the interrupt handler can clear the appropriate IFR bit. IPR reflects the state of each priority level. 7.8.2 Fast and Normal Interrupt Requests FIER allows individual enabling or masking of pending fast interrupt requests. FIER is logically ANDed with IPR, and the result is stored in FIPR. FIPR bits are bit-wise ORed together and inverted to form the fast interrupt signal routed to the M*CORE processor. The FIPR allows software to quickly determine the highest priority pending fast interrupt. The output of FIPR also feeds into a 32-to-5 priority encoder to generate the vector number to present to the M*CORE processor if vectored interrupts are required. NIER allows individual enabling or masking of pending normal interrupt requests. NIER is logically ANDed with IPR, and the result is stored in NIPR. NIPR bits are bit-wise ORed together and inverted to form the normal interrupt signal routed to the M*CORE processor. The normal interrupt signal is only asserted if the fast interrupt signal is negated. The NIPR allows software to quickly determine the highest priority pending normal interrupt. The output of NIPR also feeds into a 32-to-5 priority encoder to generate the vector number to present to the M*CORE processor if vectored interrupts are required. If the fast interrupt signal is asserted, then the vector number is determined by the highest priority fast interrupt. Technical Data 168 MMC2107 - Rev. 2.0 Interrupt Controller Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Interrupt Controller Module Functional Description If an interrupt is pending at a given priority level and both the corresponding FIER and NIER bits are set, then both the corresponding FIPR and NIPR bits are set, assuming these bits are not masked. Fast interrupt requests always have priority over normal interrupt requests, even if the normal interrupt request is at a higher priority level than the highest fast interrupt request. If the fast interrupt signal is asserted when the normal interrupt signal is already asserted, then the normal interrupt signal is negated. Freescale Semiconductor, Inc... IPR, NIPR, and FIPR are read-only. To clear a pending interrupt, the interrupt must be cleared at the source using a special clearing sequence defined by each source. All interrupt sources to the interrupt controller are to be held until recognized and cleared by the interrupt service routine. The interrupt controller does not have any edge-detect logic. Edge-triggered interrupt sources are handled at the source module. In ICR, the MASK[4:0] bits can mask interrupt sources at and below a selected priority level. The MFI bit determines whether the mask applies only to normal interrupts or to fast interrupts with all normal interrupts being masked. The ME bit enables interrupt masking. ISR reflects the current vector number and the states of the signals to the M*CORE processor. The vector number and fast/normal interrupt sources are synchronized before being sent to the M*CORE processor. Thus, the interrupt controller adds one clock of latency to the interrupt sequence. The fast and normal interrupt raw sources are not synchronized to allow these signals to be used to wake up the M*CORE processor during stop mode when all system clocks are stopped. 7.8.3 Autovectored and Vectored Interrupt Requests The AE bit in ICR enables autovectored interrupt requests to the M*CORE processor. AE is set by default, and all interrupt requests are autovectored. An interrupt handler may read FIPR or NIPR to determine the priority of the interrupt source. If multiple interrupt sources share the same priority level, then it is up to the interrupt service routine to determine the correct source of the interrupt. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Interrupt Controller Module For More Information On This Product, Go to: www.freescale.com 169 Freescale Semiconductor, Inc. Interrupt Controller Module If the AE bit is 0, then each interrupt request is presented with a vector number. The low five bits of the vector number (4-0) are determined based on the highest pending priority, with active fast interrupts having priority over active normal interrupts. The remaining two bits (vector bits 5 and 6) are determined based on whether the interrupt request is a fast interrupt and the setting of the FVE bit. If FVE is set, then a fast interrupt request has a vector number different from that of a normal interrupt request as shown in Table 7-4. Freescale Semiconductor, Inc... Table 7-4. Fast Interrupt Vector Number Fast Interrupt FVE Interrupt Vector Bits 6:5 No X 01 X 0 01 Yes 1 10 If FVE is 0, both normal and fast interrupts requests assigned to priority levels 0-31 are mapped to vector numbers 32-63 in the vector table. If FVE is 1, normal interrupt requests assigned to priority levels 0-31 are mapped to vector numbers 32-63 in the vector table. If FVE is 1, then fast interrupt requests assigned to priority levels 0-31 are mapped to vector numbers 64-95 in the vector table. See Table 7-5. Table 7-5. Vector Table Mapping Vector Number Usage Interrupt Vector Bits 6:5 0-31 Fixed exceptions (including autovectors) 00 32-63 Vectored interrupts 32 = lowest priority 63 = highest priority 01 64-95 Vectored interrupts 64 = lowest priority 95 = highest priority 10 96-127 Vectored interrupts (not used) 11 Technical Data 170 MMC2107 - Rev. 2.0 Interrupt Controller Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Interrupt Controller Module Functional Description 7.8.4 Interrupt Configuration Freescale Semiconductor, Inc... After reset, all interrupts are disabled by default. To properly configure the system to handle interrupt requests, configuration must be performed at three levels: * M*CORE processor * Interrupt controller * Local interrupt sources Configure the M*CORE first, the interrupt controller second, and the local interrupt sources last. 7.8.4.1 M*CORE Processor Configuration For fast interrupts, set the FIE[x] bit in FIER in the M*CORE processor. For normal interrupts, set the NIE[x] bit. Both FIE and NIE are cleared at reset. To allow long latency, multicycle instructions to be interrupted before completion, set the IC bit. VBR in the M*CORE processor defines the base address of the exception vector table. If autovectors are to be used, then initialize the INT and FINT autovectors (vector numbers 10 and 11, respectively). If vectored interrupts are to be used, then initialize the vectored interrupts (vector numbers 32-63 and/or 64-95). Whether 32 or 64 vectors are required depends on whether the fast interrupts share vectors with the normal interrupt sources based on the FVE bit in the interrupt controller ICR. For each vector number, create an interrupt service routine to service the interrupt, clear the local interrupt flag, and return from the interrupt routine. 7.8.4.2 Interrupt Controller Configuration By default, each interrupt source to the interrupt controller is assigned a priority level of 0 and disabled. Each interrupt source can be programmed to one of 32 priority levels and enabled as either a fast or normal interrupt source. Also, the FVE and AE bits in ICR can be programmed to select autovectored/vectored interrupts and also determine if the fast interrupt vector number is to be separate from the normal interrupt vector. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Interrupt Controller Module For More Information On This Product, Go to: www.freescale.com 171 Freescale Semiconductor, Inc. Interrupt Controller Module 7.8.4.3 Interrupt Source Configuration Each module that is capable of generating an interrupt request has an interrupt request enable/disable bit. To allow the interrupt source to be asserted, set the local interrupt enable bit. Freescale Semiconductor, Inc... Once an interrupt request is asserted, the module keeps the source asserted until the interrupt service routine performs a special sequence to clear the interrupt flag. Clearing the flag negates the interrupt request. 7.8.5 Interrupts The interrupt controller assigns a number to each interrupt source, as Table 7-6 shows. Table 7-6. Interrupt Source Assignment Source Module 0 Flag Source Description Flag Clearing Mechanism PF1 Queue 1 conversion pause CF1 Queue 1 conversion complete Write CF1 = 0 after reading CF1 = 1 2 PF2 Queue 2 conversion pause 3 CF2 Queue 2 conversion complete Write CF2 = 0 after reading CF2 = 1 1 Write PF1 = 0 after reading PF1 = 1 ADC 4 MODF Write PF2 = 0 after reading PF2 = 1 Mode fault Write to SPICR1 after reading MODF = 1 SPI 5 SPIF Transfer complete Access SPIDR after reading SPIF = 1 6 TDRE Transmit data register empty Write SCIDRL after reading TDRE = 1 7 TC Transmit complete Write SCIDRL after reading TC = 1 Receive data register full Read SCIDRL after reading RDRF = 1 8 SCI1 RDRF 9 OR Receiver overrun Read SCIDRL after reading OR = 1 10 IDLE Receiver line idle Read SCIDRL after reading IDLE = 1 11 TDRE Transmit data register empty Write SCIDRL after reading TDRE = 1 12 TC Transmit complete Write SCIDRL after reading TC = 1 Receive data register full Read SCIDRL after reading RDRF = 1 13 SCI2 RDRF 14 OR Receiver overrun Read SCIDRL after reading OR = 1 15 IDLE Receiver line idle Read SCIDRL after reading IDLE = 1 Technical Data 172 MMC2107 - Rev. 2.0 Interrupt Controller Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Interrupt Controller Module Functional Description Table 7-6. Interrupt Source Assignment (Continued) Source Module Source Description Flag Clearing Mechanism 16 C0F Timer channel 0 Write C0F = 1 or access IC/OC if TFFCA = 1 17 C1F Timer channel 1 Write 1 to C1F or access IC/OC if TFFCA = 1 18 C2F Timer channel 2 Write 1 to C2F or access IC/OC if TFFCA = 1 C3F Timer channel 3 Write 1 to C3F or access IC/OC if TFFCA = 1 20 TOF Timer overflow Write TOF = 1 or access TIMCNTH/L if TFFCA = 1 21 PAIF Pulse accumulator input Write PAIF = 1 or access PAC if TFFCA = 1 19 Freescale Semiconductor, Inc... Flag TIM1 22 PAOVF Pulse accumulator overflow Write PAOVF = 1 or access PAC if TFFCA = 1 23 C0F Timer channel 0 Write C0F = 1 or access IC/OC if TFFCA = 1 24 C1F Timer channel 1 Write C1F = 1 or access IC/OC if TFFCA = 1 25 C2F Timer channel 2 Write C2F = 1 or access IC/OC if TFFCA = 1 C3F Timer channel 3 Write C3F = 1 or access IC/OC if TFFCA = 1 27 TOF Timer overflow Write TOF = 1 or access TIMCNTH/L if TFFCA = 1 28 PAIF Pulse accumulator input Write PAIF = 1 or access PAC if TFFCA = 1 26 TIM2 29 PAOVF Pulse accumulator overflow Write PAOVF = 1 or access PAC if TFFCA = 1 30 PIT1 PIF PIT interrupt flag Write PIF = 1 or write PMR 31 PIT2 PIF PIT interrupt flag Write PIF = 1 or write PMR 32 EPF0 Edge port flag 0 Write EPF0 = 1 33 EPF1 Edge port flag 1 Write EPF1 = 1 34 EPF2 Edge port flag 2 Write EPF2 = 1 EPF3 Edge port flag 3 Write EPF3 = 1 EPF4 Edge port flag 4 Write EPF4 = 1 37 EPF5 Edge port flag 5 Write EPF5 = 1 38 EPF6 Edge port flag 6 Write EPF6 = 1 39 EPF7 Edge port flag 7 Write EPF7 = 1 35 36 EPORT MMC2107 - Rev. 2.0 MOTOROLA Technical Data Interrupt Controller Module For More Information On This Product, Go to: www.freescale.com 173 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Interrupt Controller Module Technical Data 174 MMC2107 - Rev. 2.0 Interrupt Controller Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 8. Static Random-Access Memory (SRAM) Freescale Semiconductor, Inc... 8.1 Contents 8.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 8.3 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175 8.4 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 8.5 Standby Power Supply Pin (VSTBY) . . . . . . . . . . . . . . . . . . . . 176 8.6 Standby Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 8.7 Reset Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 8.8 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 8.2 Introduction Features of the static random-access memory (SRAM) include: * On-chip, 8-Kbyte static random-access memory (SRAM) * Fixed address space * Byte, half-word (16-bit), or word (32-bit) read/write accesses * One clock per access (including bytes, half-words, and words) * Supervisor or user mode access * Standby power supply switch to support an external power supply 8.3 Modes of Operation Access to the SRAM is not restricted in any way. The array can be accessed in all supervisor and user modes. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Static Random-Access Memory (SRAM) For More Information On This Product, Go to: www.freescale.com 175 Freescale Semiconductor, Inc. Static Random-Access Memory (SRAM) 8.4 Low-Power Modes In wait, doze, and stop modes, clocks to the SRAM are disabled. No recovery time is required when exiting any low-power mode. 8.5 Standby Power Supply Pin (VSTBY) Freescale Semiconductor, Inc... The standby power supply pin (VSTBY) provides standby voltage to the RAM array if VDD is lost. VSTBY is isolated from all other VDD nodes. 8.6 Standby Operation When the chip is powered down, the contents of the SRAM array are maintained by the standby power supply, VSTBY. If the standby voltage falls below the minimum required voltage, the SRAM contents may be corrupted. The SRAM automatically switches to standby operation with no loss of data when the voltage on VDD is below the voltage on VSTBY. In standby mode, the SRAM does not respond to any bus cycles. Unexpected operation may occur if the central processor unit (CPU) requests data from the SRAM in standby mode. If standby operation is not needed, then the VSTBY pin should be connected to VDD. The current on VSTBY may exceed its specified maximum value at some time during the transition time during which VDD is at or below the voltage switch threshold to a threshold above VSS. If the standby power supply cannot provide enough current to maintain VSTBY above the required minimum value, then a capacitor must be provided from VSTBY to VSS. The value of the capacitor, C, can be calculated as: t C = I x ---V where: I is the difference between the transition current requirement and the maximum power supply current, t is the duration of the VDD transition near the voltage switch threshold, and V is the difference between the minimum available supply voltage and the required minimum VSTBY voltage. Technical Data 176 MMC2107 - Rev. 2.0 Static Random-Access Memory (SRAM) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Static Random-Access Memory (SRAM) Reset Operation 8.7 Reset Operation The SRAM contents are undefined immediately following a power-on reset. SRAM contents are unaffected by system reset. If a synchronous reset occurs during a read or write access, then the access completes normally and any pipelined access in progress is stopped without corruption of the SRAM contents. Freescale Semiconductor, Inc... 8.8 Interrupts The SRAM module does not generate interrupt requests. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Static Random-Access Memory (SRAM) For More Information On This Product, Go to: www.freescale.com 177 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Static Random-Access Memory (SRAM) Technical Data 178 MMC2107 - Rev. 2.0 Static Random-Access Memory (SRAM) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 9. Non-Volatile Memory FLASH (CMFR) Freescale Semiconductor, Inc... 9.1 Contents 9.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 9.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 9.4 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .182 9.4.1 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .182 9.4.2 Disabled Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182 9.5 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 9.6 Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 9.7 Registers and Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . 186 9.7.1 Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .187 9.7.1.1 CMFR Module Configuration Register . . . . . . . . . . . . . .188 9.7.1.2 CMFR Module Test Register . . . . . . . . . . . . . . . . . . . . . 193 9.7.1.3 CMFR High-Voltage Control Register . . . . . . . . . . . . . . 196 9.7.2 Array Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .203 9.7.2.1 Read Page Buffers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203 9.7.2.2 Program Page Buffers . . . . . . . . . . . . . . . . . . . . . . . . . . 204 9.8 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 9.8.1 Master Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 9.8.2 Register Read and Write Operation . . . . . . . . . . . . . . . . . . 205 9.8.3 Array Read Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 9.8.4 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206 9.8.4.1 Program Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207 9.8.4.2 Program Margin Reads . . . . . . . . . . . . . . . . . . . . . . . . . 211 9.8.4.3 Programming Shadow Information. . . . . . . . . . . . . . . . . 212 9.8.4.4 Program Pulse-Width and Amplitude Modulation . . . . . 213 9.8.4.5 Overprogramming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com 179 Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Freescale Semiconductor, Inc... 9.8.5 9.8.5.1 9.8.5.2 9.8.5.3 9.8.6 9.8.7 Erasing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214 Erase Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 Erase Margin Reads . . . . . . . . . . . . . . . . . . . . . . . . . . . 218 Erasing Shadow Information Words. . . . . . . . . . . . . . . . 219 Erase Pulse Amplitude and Width Modulation . . . . . . . . . . 219 Emulation Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 9.9 Master Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .220 9.10 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 9.2 Introduction This section describes the operation of the embedded FLASH memory. The FLASH memory can be read, programmed, and erased from a single external programming voltage supply, VPP. The program and erase operations are enabled through the use of an internal charge pump. The CDR MoneT FLASH uses the Motorola one-transistor bitcell (MoneT). The 128-Kbyte CMFR array is divided into 16-Kbyte (16,384 bytes) array blocks. The CMFR array size is created by using eight array blocks. The primary function of the CMFR is to serve as electrically programmable and erasable NVM to store program instructions and/or data. It is a class of nonvolatile solid state silicon memory device consisting of an array of isolated elements, a means for selectively adding and removing charge to the elements electrically and a means of selectively sensing the stored charge in the elements. When power is removed from the device, the stored charge of the isolated elements are retained. The CMFR is arranged into two major sections as shown in Figure 9-1. The first section is the MoneT array used to store system program and data. The second section is the bus interface unit (BIU) that controls access and operation of the CMFR array. Technical Data 180 MMC2107 - Rev. 2.0 Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Features 9.3 Features Features of the CMFR module include: * MoneT FLASH bitcell * 128-Kbyte array size using 16-Kbyte blocks * Array block restriction control: Freescale Semiconductor, Inc... - - - - Array block erasing Array protection for program and erase operations Supervisor space and supervisor/unrestricted space selection Data space and instruction/data spaces selection. * 32-bit word length * Page mode read: - - - - * Retains two separate pages Read page size of 32 bytes (8 words) Off-page read access time of two clocks On-page read access time of one clock Programming: - Program up to 512 bytes at a time - Simultaneously program up to eight 64-byte pages located at the same block offset address * External VPP program and erase power supply MMC2107 - Rev. 2.0 MOTOROLA Technical Data Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com 181 Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) 9.4 Modes of Operation This subsection describes the two modes of operation: 1. Stop mode 2. Disabled mode Freescale Semiconductor, Inc... 9.4.1 Stop Mode When the FSTOP bit in the CMFR module configuration register (CMFRMCR) register is set, the CMFR enters a low-power operation mode. Write to FSTOP bit is allowed only when SES = 0 in the CMFR high-voltage control register (no high-voltage operations). When the FSTOP bit is set, only CMFRMCR can be accessed, accesses to the array are ignored, and accesses to other registers are terminated with bus errors. To prevent unpredictable behavior it is recommended to change this bit separately. The CMFR requires a recovery time of 16 clocks after exiting stop mode. This means that if a read access to the array is done immediately after writing FSTOP = 0, the access is completed after 16 clocks. 9.4.2 Disabled Mode When the DIS bit in CMFRMCR is set, the array is disabled and the BIU does not respond to array accesses. Write to DIS bit is allowed only when SES = 0 (no high-voltage operations). Disabling the CMFR does not place the module in the lowest power consumption mode like stop mode, but does place the CMFR in a safe state and prevents the CMFR from conflicting on the internal bus during an external boot. There is no recovery time required when re-enabling the CMFR. For details of the CMFR module configuration register (CMFRMCR) see 9.7.1.1 CMFR Module Configuration Register and 9.7.1.3 CMFR High-Voltage Control Register. Technical Data 182 MMC2107 - Rev. 2.0 Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Block Diagram 9.5 Block Diagram 64-BYTE PROGRAM PAGE BUFFER 7 16-KBYTE ARRAY BLOCK 7 0x0001_c000--0x0001_ffff 64-BYTE PROGRAM PAGE BUFFER 6 16-KBYTE ARRAY BLOCK 6 0x0001_8000--0x0001_bfff Freescale Semiconductor, Inc... 32-BYTE READ PAGE BUFFER 1 16-KBYTE ARRAY BLOCK 5 0x0001_4000--0x0001_7fff 64-BYTE PROGRAM PAGE BUFFER 5 16-KBYTE ARRAY BLOCK 4 0x0001_0000--0x0001_3fff 64-BYTE PROGRAM PAGE BUFFER 4 64-BYTE PROGRAM PAGE BUFFER 3 16-KBYTE ARRAY BLOCK 3 0x0000_c000--0x0000_ffff 64-BYTE PROGRAM PAGE BUFFER 2 16-KBYTE ARRAY BLOCK 2 0x0000_8000--0x0000_bfff 32-BYTE READ PAGE BUFFER 0 16-KBYTE ARRAY BLOCK 1 0x0000_4000--0x0000_7fff 64-BYTE PROGRAM PAGE BUFFER 1 16-KBYTE ARRAY BLOCK 0 AND SHADOW INFORMATION 0x0000_0000--0x0000_3fff 64-BYTE PROGRAM PAGE BUFFER 0 BUS INTERFACE UNIT (BIU) Figure 9-1. CMFR 128-Kbyte Block Diagram The CMFR is divided into array blocks to allow for independent erase, address attributes restriction, and protection from program and erase for each array block. The size of an array block in the CMFR module is fixed at 16 Kbytes. The total CMFR array is distributed into eight blocks. For a detailed description of the read page buffer operation see 9.7.2.1 Read Page Buffers and 9.8.3 Array Read Operation. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com 183 Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Freescale Semiconductor, Inc... To improve system performance, the BIU accesses information in the array at 32 bytes per access. These 32 bytes are copied in a read page buffer aligned to the low-order addresses. A CMFR array contains two non-overlapping read page buffers. The first read page buffer is associated to the lower array blocks. The second read page buffer is associated to the higher array blocks. Read access time of the data in the current read page buffers is one system clock, while the time to read a new page into a page buffer and access the required information is two system clocks. These accesses are known as an on-page read and an off-page read, respectively. To prevent the BIU from accessing an unnecessary page from the array, the CMFR monitors the address to determine if the required information is in one of the two current read page buffers and the access is valid for the module. This strategy allows the CMFR to have a two-clock read for an off-page access and one-clock for an on-page access. In normal operation write accesses to the CMFR array are not allowed, a write access causes a bus error. The CMFR requires an external program or erase voltage, VPP, to program or erase the array. Special control logic is included to require a specific series of read and write accesses. To improve program performance, the CMFR programs up to eight unique 64-byte pages simultaneously in eight separate array blocks. These 64 bytes are aligned to the low-order addresses to form a program page buffer. Each of the pages being programmed simultaneously are located at the same block offset address. Erasing is performed on one or more of the selected array blocks simultaneously. An extra row (256 bytes) of the CMFR array is used to provide reset configuration information and is called shadow information. This row may be accessed by setting the SIE bit in the CMFR module configuration register and accessing the CMFR array. The shadow information is in the lowest array block 0 of the CMFR array. Note that the shadow row is erased with block 0. Technical Data 184 MMC2107 - Rev. 2.0 Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Glossary of Terms 9.6 Glossary of Terms Array block - CMFR array subdivision is a 16-Kbyte contiguous block of information. Each array block can be erased independently. BIU - Bus interface unit that controls access and operation of the CMFR CMFR - CDR MoneT FLASH ARray Freescale Semiconductor, Inc... Erase interlock write - A write to any CMFR array address after initializing the erase sequence Erase margin read - Special off-page read of the CMFR array in which the CMFR hardware adjusts the reference of the sense amplifier to check for correct erase operation. All CMFR off-page reads between the erase interlock write and clearing the SES bit are erase margin reads. Initialize program/erase sequence - The write to the high-voltage control register that changes the SES bit from a 0 to a 1 MoneT - The Motorola one-transistor bitcell Off-page read - Array read operation that requires two clocks and updates a page buffer On-page read - Array read operation that accesses information in one of the read page buffers and requires one clock. Overprogrammed - By exceeding the specified programming time and/or voltage, a CMFR bit can be overprogrammed. This causes erased bits in the same column in the same array block to read as programmed. Programming write - A write to a CMFR array address to transfer information into a program page buffer. The CMFR accepts programming writes after initializing the program sequence until the EHV bit is changed from a 0 to a 1. Program margin read - Special off-page read of the CMFR array in which the CMFR hardware adjusts the reference of the sense amplifier to check for correct program operation. All CMFR array off-page reads between the first programming write and clearing the SES bit are program margin reads. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com 185 Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Program page buffer - 64 bytes of information used to program the CMFR. This information is aligned to a 64-byte boundary within the CMFR. The CMFR module has eight program page buffers, one per array block. Freescale Semiconductor, Inc... Read page buffer - 32-byte block of information that is read from the CMFR array. This information is aligned to a 32-byte boundary within the CMFR. The CMFR module has two read page buffers. Shadow information - An extra row (256 bytes) of the CMFR array used to provide Motorola internal use data and also possibly user defined information. This row may be accessed by setting the SIE bit in the CMFR module configuration register and accessing the CMFR array. The shadow information is the lowest array block 0 of the CMFR array. 9.7 Registers and Memory Map The CMFR module consists of two addressed sections. The first is the 32-byte control registers used to configure, program, erase, and test the array while, the second is the array. See Figure 9-2. 0x00d0_001f UNIMPLEMENTED CMFR HIGH-VOLTAGE CONTROL REGISTER (CMFRCTL) CMFR MODULE TEST REGISTER (CMFRMTR) CMFR MODULE CONFIGURATION REGISTER (CMFRMCR) 0x00d0_0020 0x00d0_0000 FLASH CONTROL 32 BYTES 0x00d0_000c 0x00d0_000b 0x00d0_0008 0x00d0_0007 0x00d0_0004 0x00d0_0003 0x00d0_0000 0x0001_ffff CMFR FLASH 128 KBYTES 0x0000_0000 Figure 9-2. CMFR Array and Control Register Addressing Technical Data 186 MMC2107 - Rev. 2.0 Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Registers and Memory Map 9.7.1 Control Registers The control registers control CMFR operation. On reset, the registers are loaded with default reset information. Freescale Semiconductor, Inc... Table 9-1. Non-Volatile Memory FLASH Memory Map Address Control Register Located in Supervisor Data Space 0x00d0_0000 Module configuration register (CMFRMCR) 0x00d0_0004 Module test register (CMFRMTR) 0x00d0_0008 High-voltage control register (CMFRCTL) 0x00d0_000c through 0x00d0_001f Unimplemented The access time of a CMFR register is one system clock for both read and write accesses. Accesses to unimplemented registers cause the BIU to generate a transfer error exception. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com 187 Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) 9.7.1.1 CMFR Module Configuration Register The CMFR module configuration register (CMFRMCR) controls operation of the CMFR array and BIU. Address: 0x00d0_0000 through 0x00d0_0003 Bit 31 30 28 27 26 25 Bit 24 FSTOP FDBG EME SIE LOCKCTL DIS RSVD24 0 0 0 Note 1 0 0 Note 1 0 Bit 23 22 21 20 19 18 17 Bit 16 SUPV7 SUPV6 SUPV5 SUPV4 SUPV3 SUPV2 SUPV1 SUPV0 1 1 1 1 1 1 1 1 Bit 15 14 13 12 11 10 9 Bit 8 DATA7 DATA6 DATA5 DATA4 DATA3 DATA2 DATA1 DATA0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Read: 29 0 Freescale Semiconductor, Inc... Write: Reset: Read: Write: Reset: Read: Write: Reset: Read: PROTECT7 PROTECT6 PROTECT5 PROTECT4 PROTECT3 PROTECT2 PROTECT1 PROTECT0 Write: Reset: 1 1 1 1 1 1 1 1 = Writes have no effect and the access terminates without a transfer error exception. Notes: 1. Reset state is determined during reset configuration. Figure 9-3. CMFR Module Configuration Register (CMFRMCR) Technical Data 188 MMC2107 - Rev. 2.0 Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Registers and Memory Map FSTOP -- FLASH Stop Enable Bit The read-always FSTOP bit causes the CMFR to enter a low-power stop mode. Writing has no effect if SES = 1. When FSTOP is set, the BIU continues to operate to allow accesses to CMFRMCR. Accesses to other registers are terminated with bus error. Accesses to the array are ignored. To prevent unpredictable behavior, change the FSTOP bit in a separate write operation. 1 = CMFR in low-power stop mode 0 = CMFR in normal mode Freescale Semiconductor, Inc... FDBG -- FLASH Debug Enable Bit The read/write FDBG bit determines whether the set-once LOCKCTL bit is writable when the chip is in debug mode. Writing to the FDBG bit must occur before the LOCKCTL bit is writable. 1 = Debug mode enabled 0 = Debug mode disabled EME -- Emulation Enable Bit The read-always EME bit enables the CMFR to enter emulation mode. EME is writable when the LOCKCTL and DIS bits are set. During emulation mode the CMFR terminates array access cycles, but does not drive data. Array data can be emulated by reading an external memory, and on-page/off-page timing is the same as in non-emulation mode. Note that write accesses to the array space are the same as normal mode. 1 = Emulation mode enabled 0 = Emulation mode disabled For more information about emulation operation see 9.8.7 Emulation Operation. SIE -- Shadow Information Enable Bit The read-always SIE bit selects the shadow information row. SIE is write-protected when the ERASE bit is clear and the SES bit is set. When SIE is set and an array location is read using supervisor data, the shadow information is read from a location determined by the column, 32 byte read page select, and word addresses of the access. Accessing the control block registers accesses the registers and not the shadow information. 1 = Shadow information enabled; normal array access disabled 0 = Shadow information disabled; normal array access enabled MMC2107 - Rev. 2.0 MOTOROLA Technical Data Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com 189 Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) The address range of the shadow information is the entire address range of the array, but the high order array addresses, are not used to encode the location. NOTE: When SIE = 1, only the program page buffer associated with the lowest block can be programmed. The other program page buffers cannot be accessed and do not apply any programming voltages to their array blocks while programming the shadow information. The shadow information is in block 0. Freescale Semiconductor, Inc... LOCKCTL -- Lock Control Bit The read-always, set-once LOCKCTL bit controls the write-lock function. Once the LOCKCTL bit is set in normal operation, the write-lock can only be disabled again by a master reset. The LOCKCTL bit is writable if the device is in debug mode. 1 = Write-locked registers protected 0 = Write-lock disabled Setting the LOCKCTL bit locks the SUPV[7:0], DATA[7:0] and PROTECT[7:0] bits. Writing to these bits has no effect; the cycle ends normally and the bits do not change. NOTE: If LOCKCTL is set before PROTECT[7:0] is cleared, the device must use debug mode to program or erase the CMFR. The default reset state of LOCKCTL is 0. It can be set once after master reset to allow protection of the write-locked register bits after initialization. If the LOCKCTL bit and write-locked register bits are written simultaneously, the new value does not affect the current cycle. DIS -- Disable Bit The read-always DIS bit disables array information. Writing to DIS has no effect if the SES bit is set. When DIS is set, the array is disabled and the CMFR BIU does not respond to array accesses. The reset value is defined during reset configuration by the external D28 pin. 1 = Array information disabled 0 = Array information enabled Technical Data 190 MMC2107 - Rev. 2.0 Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Registers and Memory Map RSVD24 -- Reserved Writing to this read/write bit updates the value but has no effect on functionality. SUPV[7:0] -- Supervisor Space Field The read-always SUPV[7:0] field controls supervisor/unrestricted address space assignment of array blocks. The field is writable when the LOCKCTL bit is clear. Freescale Semiconductor, Inc... Array blocks that correspond to 1s in SUPV[7:0] are selected for data address space. Each array block can be mapped into supervisor or unrestricted address space. When an array block is mapped into supervisor address space (SUPV[M] = 1) only supervisor accesses are allowed. A user access to a location in supervisor address space causes a data error exception. When an array block is mapped into unrestricted address space (SUPV[M] = 0) both supervisor and user accesses are allowed. The default reset state of SUPV[7:0] bits are supervisor address space (SUPV[M] = 1). 1 = Array block in supervisor address space 0 = Array block in unrestricted address space DATA[7:0] -- Data Space Field The read-always DATA[7:0] field controls data/program address space assignment of array blocks. When LOCKCTL = 1, the DATA[7:0] field is write-protected, and writing to it has no effect. Array blocks that correspond to 1s in DATA[7:0] are selected for data address space. Each array block can be mapped into data address space or both data and program address space. When an array block is mapped into data address space (DATA[M] = 1) only data accesses are allowed. A program access to a location in data address space causes a data error exception. When an array block is mapped into both data and program address space (DATA[M] = 0) both data and program accesses are allowed. The default reset state of DATA[7:0] bits are data and program address space (DATA[M] = 0). 1 = Array block in data address space 0 = Array block is both data and program address space MMC2107 - Rev. 2.0 MOTOROLA Technical Data Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com 191 Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) PROTECT[7:0] -- Block Protect Field The read-always PROTECT[7:0] field protects array blocks from program and erase operations. If LOCKCTL = 1 or SES = 1, writing to PROTECT[7:0] has no effect. Array blocks that correspond to 1s in PROTECT[7:0] are selected for data address space. Freescale Semiconductor, Inc... Each array block can be protected from program and erase operation by setting its PROTECT bit. The CMFR BIU performs all programming and erase interlocks except that the program and erase voltages are not applied to locations within the protected array block(s). The default reset state of PROTECT[7:0] bits are protected (PROTECT[M] = 1). 1 = Array block protected 0 = Array block not protected CAUTION: If the LOCKCTL bit is set before PROTECT[7:0] is cleared, the device must use debug mode to program or erase the CMFR. Technical Data 192 MMC2107 - Rev. 2.0 Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Registers and Memory Map 9.7.1.2 CMFR Module Test Register The CMFR module test register (CMFRMTR) controls the CMFR array and BIU. Address: 0x00d0_0004 through 0x00d0_0007 Read: Bit 31 30 29 28 27 26 25 Bit 24 0 0 0 0 0 0 0 0 Bit 23 22 21 20 19 18 17 Bit 16 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 NVR PAWS2 PAWS1 PAWS0 0 0 0 0 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 Freescale Semiconductor, Inc... Write: Reset: Read: Write: Reset: Read: Write: Reset: Bit 7 Read: 6 5 RSVD6 GDB 0 0 0 Write: Reset: 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 9-4. CMFR Module Test Register (CMFRMTR) MMC2107 - Rev. 2.0 MOTOROLA Technical Data Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com 193 Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) NVR -- Negative Voltage Range Select Bit The read-always NVR bit modulates the negative pump output to select the negative voltage range in program and erase modes as shown in Table 9-2. NVR is writable when the HVS bit is clear but has no effect when the GDB bit is clear. 1 = Negative voltage low range 0 = Negative voltage high range Freescale Semiconductor, Inc... Table 9-2. Negative Voltage Modulation PAWS[2:0] NVR = 0 NVR = 1 100 -6 V -2 V 101 -7 V -3 V 110 -8 V -4 V 111 -9 V -5 V 0XX Reserved(1) 1. When PAWS[2] = 0 and PAWS[1:0] have no effect. PAWS[2:0] -- Pulse Amplitude/Width Select Field The read-always PAWS[2:0] field selects the pulse drain amplitude and width for program or erase operations. PAWS[2:0] is writable when the HVS bit is clear. PAWS[2] must be set for all program and erase operations. If GDB = 1, the gate/source voltage applied during program/erase is determined by PAWS[1:0] and NVR and shown in Table 9-2. NOTE: The program pulse time is equal to the value selected by the pulse width timing control. When SES = 1, write to SCLKR[2:0], CLKPE[1:0], and CLKPM[6:0] only when PAWS[2] = 1. Do not write to PAWS[2:0] during high-voltage operations. RSVD6 -- Reserved Reserved for factory test and must remain clear at all times Technical Data 194 MMC2107 - Rev. 2.0 Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Registers and Memory Map GDB -- Gate or Drain/Source Select Bit The read-always GDB bit selects gate, source, or drain for voltage modulation. GDB is writable when the SES bit is clear. Freescale Semiconductor, Inc... GDB selects the gate, source, or drain. In programming, GDB selects gate (GDB = 1) or drain (GDB = 0) voltage for amplitude modulation. When PAWS[2] = 0, mask plugs control amplitude modulation. When PAWS[2] = 1, the PAWS[1:0] bits control amplitude modulation. 1 = Gate selected 0 = Drain/source selected Table 9-3. Drain Amplitude Modulation (GDB = 0) PAWS[2:0] Drain Voltage 100 60% VPP 101 70% VPP 110 80% VPP 111 VPP MMC2107 - Rev. 2.0 MOTOROLA Technical Data Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com 195 Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) 9.7.1.3 CMFR High-Voltage Control Register The CMFR high-voltage control register (CMFRCTL) controls the program and erase operations of the CMFR. Address: 0x00d0_0008 through 0x00d0_000b Bit 31 Read: 30 29 28 27 SCLKR2 SCLKR1 SCLKR0 0 HVS 26 25 Bit 24 CLKPE1 CLKPE0 0 Freescale Semiconductor, Inc... Write: Reset: Read: 0 0 0 0 0 0 0 0 Bit 23 22 21 20 19 18 17 Bit 16 CLKPM6 CLKPM5 CLKPM4 CLKPM3 CLKPM2 CLKPM1 CLKPM0 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 BLOCK7 BLOCK6 BLOCK5 BLOCK4 BLOCK3 BLOCK2 BLOCK1 BLOCK0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 1 0 0 ERASE SES EHV 0 0 0 0 Write: Reset: Read: Write: Reset: Read: 0 RSVD6 Write: Reset: 0 0 1 0 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 9-5. CMFR High-Voltage Control Register (CMFRCTL) HVS -- High Voltage Status Bit The read-only HVS bit reflects the status of the program/erase pulse. Writing to HVS has no effect. HVS is set when a pulse is active and during recovery. While HVS = 1, accesses to the array cause a bus error, and SES cannot be changed. The pulse becomes active when the EHV bit is set and is terminated by clearing EHV or by the pulse width timing control. See Figure 9-6. 1 = Pulse applied to array or CMFR in recovery 0 = Pulse not applied to array Technical Data 196 MMC2107 - Rev. 2.0 Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Registers and Memory Map EHV HVS PULSE WIDTH RECOVERY RECOVERY Recovery = 48 scaled clocks or 128 clocks Freescale Semiconductor, Inc... Figure 9-6. Pulse Status Timing The recovery time is the time that the CMFR requires to remove the program or erase voltage from the array before switching to another mode of operation. The recovery time is determined by the SCLKR[2:0] field and the ERASE bit. If SCLKR is not 000, the recovery time is 48 of the scaled clock periods. If SCLKR = 000 the recovery time is 128 clocks. Once reset is completed HVS indicates no program or erase pulse (HVS = 0). SCLKR[2:0] -- System Clock Range Field The read/write SCLKR[2:0] field selects the system clock range for program/erase pulse timing. NOTE: The SCLKR[2:0] bits are not write protected by the SES bit. Unless the PAWS[2] bit is set, writes to SCLKR[2:0] in software should not be changed if SES = 1. To control the pulse widths for program and erase operations, the CMFR uses the system clock and the timing control in CMFRCTL. The total pulse time is defined by: pulse width = system clock period x R x 2N x M Where: R = clock scaling (see Table 9-4) N = 5 + CLKPE[1:0] + ( (ERASE) x 10) M = 1 + CLKPM[6:0] MMC2107 - Rev. 2.0 MOTOROLA Technical Data Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com 197 Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Table 9-4. System Clock Range System Clock Frequency (MHz) SCLKR[2:0] Minimum Freescale Semiconductor, Inc... 000 Maximum(1) Clock Scaling (R) Reserved 001 8 12 1 010 12 18 3/2 011 18 24 2 100 24 36 3 101 36 40 4 110 and 111 Reserved by Motorola for future use 1. The maximum system clock frequency is 33 MHz. The control of the program/erase pulse timing is divided into three functions. The first term of the timing control is the clock scaling, R. The value of R is determined by the system clock range (SCLKR[2:0]). SCLKR[2:0] defines the base clock of the pulse timer. Use Table 9-4 to set SCLKR[2:0] based on the system clock frequency. CAUTION: If the correct value for SCLKR[2:0] is not selected from the table, the pulse timer may run too fast and cause damage to the device. The system clock period is multiplied by the clock scaling value to generate a 83.3-ns to 125-ns scaled clock. This scaled clock is used to run the charge pump submodule and the next functional block of the timing control. NOTE: The minimum specified system clock frequency for program and erase operations is 8.0 MHz. The CMFR does not have any means to monitor the system clock frequency and cannot prevent program or erase operation at frequencies below 8.0 MHz. Attempting to program or erase the CMFR at system clock frequencies lower than 8.0 MHz does not damage the device if the maximum pulse times and total times are not exceeded. While some bits in the CMFR array may change state if programmed or erased at system clock frequencies below 8.0 MHz, the full program or erase transition is not assured. Technical Data 198 MMC2107 - Rev. 2.0 Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Registers and Memory Map CAUTION: Never stop or alter the system clock frequency during a program or erase operation. Changing the clock frequency during program or erase results in inaccurate pulse widths and variations in the charge pump output. The default reset state of SCLKR[2:0] is 000, giving a clock scaling of 1, and the program or erase pulse is not terminated until EHV is cleared by a software write. CLKPE[1:0] -- Clock Period Exponent Field Freescale Semiconductor, Inc... The read/write CLKPE[1:0] field selects the clock period exponent for program/erase pulse timing. The second term of the timing control is the clock multiplier, 2N. The program pulse number (pulse), clock period exponent bits (CLKPE[1:0]), and ERASE define the exponent in the 2N multiply of the clock period. The exponent, N, is defined by the equation: N = 5 + CLKPE[1:0] + [(ERASE) x 10] All of the exponents are shown in Table 9-5. NOTE: The CLKPE[1:0] bits are not write protected by the SES bit. Unless the PAWS[2] bit is set, writes to CLKPE[1:0] in software should not be changed if SES = 1. The default reset state of CLKPE[1:0] is 00 . Table 9-5. Clock Period Exponent and Pulse Width Range Pulse Width Range for all System Clock Frequencies from 8.0 MHz to 33.0 MHz ERASE CLKPE[1:0] Exponent (N) 2N 0 1 Minimum x 1.25E - 7 Maximum(1) 2N x 128 x 8.33E - 8 00 5 4.00 s 0.34 ms 01 6 8.00 s 0.68 ms 10 7 16.00 s 1.36 ms 11 8 32.0 s 2.73 ms 00 15 4.096 ms 349.5 ms 01 16 8.192 ms 699.0 ms 10 17 16.39 ms 1.398 s 11 18 32.77 ms 2.796 s 1. The maximum system clock frequency is 33 MHz. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com 199 Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) CLKPM[6:0] -- Clock Period Multiplier Field The third term of the timing control is the linear clock multiplier, M. The clock period multiplier, CLKPM[6:0], defines a linear multiplier for the program or erase pulse. M is defined by: M = 1 + (CLKPM[6:0]) This allows the program/erase pulse to be from 1 to 128 times the pulse set by the system clock period, SCLKR[2:0] and CLKPE[1:0]. Freescale Semiconductor, Inc... The default reset state of CLKPM[6:0] is binary 000 0000, which gives a multiplier of 1. NOTE: The CLKPM[6:0] bits are not write protected by the SES bit. Unless the PAWS[2] bit is set, writes to CLKPM[6:0] in software should not be changed if SES = 1. Table 9-6 shows an example of calculating the values of SCLKR[2:0], CLKPE[1:0] and CLKPM[6:0] for a 1-ms program pulse, ERASE = 0, in a system with a 33.0-MHz system clock having a period of 30.3 ns. Table 9-6. Determining SCLKR[2:0], CLKPE[1:0], and CLKPM[6:0] No. Example Calculation 1 Determine SCLKR[2:0] -- Table 9-4 shows that a SCLKR[2:0] value of 100 and an R value of 3 gives a system clock frequency from 24 MHz to 36 MHz. 2 Determine CLKPE[1:0] -- 9.7.1 Control Registers shows that when ERASE = 0, a 1-ms program pulse can be generated by an N value of 7 (CLKPE[1:0] = 10) or 8 (CLKPE[1:0] = 11). An N value of 8 is used in this example. 3 Determine CLKPM[6:0] -- Using the selected values of N and R in the pulse width equation, pulse width = system clock period x R x 2N x M and solving for M yields 42.97. Rounding M to 43 and using the M equation, M = 1 + (CLKPM[6:0]) and solving for CLKPM[6:0] yields 42. 4 Check the results -- pulse width = 30.3 ns x 3 x 28 x 43 = 1.00 ms where SCLKR[2:0] = 100, CLKPE[1:0] = 11, CLKPM[6:0] = 0101010, ERASE = 0, system clock frequency = 33.0 MHz Technical Data 200 MMC2107 - Rev. 2.0 Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Registers and Memory Map BLOCK[7:0] -- Block Program and Erase Field Freescale Semiconductor, Inc... The read/write BLOCK[7:0] field selects array blocks for program or erase operation. BLOCK[7:0] is writable when the SES bit is clear. If SES is written in the same cycle with BLOCK[7:0] bits, the write permission to BLOCK[7:0] bits depends on the previous value of SES. Up to eight blocks at once can be selected for program operation. Array blocks that correspond to 1s in BLOCK[7:0] are selected for program or erase operation. The BLOCK[7:0] default state is $00, not selected for program or erase. 1 = Array block selected for program or erase 0 = Array block not selected for program or erase RSVD6 -- Reserved Reserved for test purposes. Writing to this read/write bit updates the values and could affect functionality if set to 1. ERASE -- Program or Erase Select Bit The read-always ERASE bit selects program or erase operations. ERASE is writable when the SES bit is clear. If SES and ERASE are written in the same cycle, the write permission to ERASE bit depends on the previous value of SES. When ERASE = 0, the array is configured for programming, and if SES = 1 the SIE bit is write locked. When ERASE = 1, the array is configured for erasing, and SES does not write lock the SIE bit. 1 = Erase operation 0 = Program operation SES -- Start/End Sequence Bit The read-always SES bit signals the start and end of a program or erase sequence. SES is writable when the HVS and EHV bits are clear. If SES and EHV are written in the same cycle, the write permission to SES depends on the previous value of EHV. At the start of a program or erase sequence, SES is set, locking PROTECT[7:0], BLOCK[7:0], and ERASE. 1 = CMFR configured for program or erase operation 0 = CMFR not configured for program or erase operation NOTE: SES does not lock the SCLKR[2:0], CLKPE[1:0], and CLKPM[6:0] bits. Do not change these bits in software when SES = 1 unless PAWS[2] = 1. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com 201 Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) At this point the CMFR is ready to receive the programming writes, the erase interlock write, or a write to CMFRMCR for programming the reset values of the DIS bit, or a write to CMFRRC. NOTE: The erase interlock write is a write to any CMFR array location after SES is set and ERASE = 1. Freescale Semiconductor, Inc... If the ERASE bit is a 0, the CMFR BIU accepts programming writes to the CMFR array address for programming. The first programming write selects the program page offset address to be programmed along with the data for the programming buffers at the location written. All programming writes after the first write update the program buffers using the lower address and the block address to select the program page buffers to receive the data. See 9.7.2.2 Program Page Buffers for further information. After the data has been written to the program buffers the EHV bit is set (written to a 1) to start the programming pulse and lock out further programming writes. If the ERASE bit is a 1, the CMFR BIU accepts writes to the CMFR array address for erase. An erase interlock write is required before the EHV bit can be set. At the end of the program or erase operation, the SES bit must be cleared (written to a 0) to return to normal operation and release the program buffers and the locked bits. The CMFR requires a recovery time of 16 clocks after negating SES. This means that if a read access to the CMFR array is done immediately after writing SES = 0, the access is completed after 16 clocks. Also, the FSTOP bit should not be asserted during this recovery time. The default reset state of SES is not configured for program or erase operation (SES = 0). EHV -- Enable High-Voltage Bit The read-always EHV bit controls the application of the program or erase voltage to the CMFR. High-voltage operations to the array, special shadow locations or NVM registers can occur only if EHV = 1. EHV can be asserted only after the SES bit has been asserted and a valid programming write(s) or erase hardware interlock write has occurred. Attempts to assert EHV when SES is negated (including the cycle which writes 0 to SES), or when a valid programming write or erase hardware interlock write has not occurred since SES was asserted have no effect. Technical Data 202 MMC2107 - Rev. 2.0 Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Registers and Memory Map Once EHV is set, SES cannot be changed; attempts to read or write the array or CMFRRC cause bus errors. The default reset state of EHV disables program or erase pulses (EHV = 0). A master reset while EHV = 1 terminates the high-voltage operation and the CMFR generates the required sequence to disable the high voltage without damage to the high-voltage circuits. 1 = Program/erase pulse enabled 0 = Program/erase pulse disabled Freescale Semiconductor, Inc... 9.7.2 Array Addressing Information in the array is accessed in 32-byte pages. Two read page buffers are aligned to the low order addresses. The first page buffer is for the lower array blocks. The second page buffer is for the higher array blocks. Access time of information in the read page buffers is one system clock. Access time for an off-page read is two system clocks. To prevent the BIU from accessing an unnecessary page from the array, the CMFR monitors the address to determine if the required information is within one of the two read page buffers and the access is valid for the module. This strategy allows the CMFR to have a 2-clock read for an off-page access and a 1-clock read for an on-page access. Writing to the array while not in a program/erase sequence causes a bus error. 9.7.2.1 Read Page Buffers The two 32-byte read page buffers are fully independent and are located in two separate read sections of the array. The BIU monitors the status and address of each page buffer. The status of the read page buffers are usually valid, but are made invalid by these operations: * Reset * Programming write * Erase interlock write * Setting the EHV bit * Clearing the SES bit * Setting or clearing the SIE bit * Exiting stop mode * Exiting disable mode * Exiting boot mode MMC2107 - Rev. 2.0 MOTOROLA Technical Data Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com 203 Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Freescale Semiconductor, Inc... Each access to the array determines if the requested location is within the current pages. If the requested location is not within the read page buffers, the appropriate read page buffer is made invalid and a new page of information is fetched from the array. The page buffer address is updated and status is made valid. If the requested location is within one of the current page buffers or has been fetched from the array, the selected bytes are transferred to the CPU, completing the access. Array accesses that make the page buffer(s) invalid are off-page reads that require two system clocks. Array accesses that do not make the page buffer(s) invalid are on-page reads that require one system clock. 9.7.2.2 Program Page Buffers The CMFR can program up to eight 64-byte pages at one time. Each program page buffer is associated with one array block. All program page buffers share the same block offset address, stored in the BIU. The block offset address is extracted from the address of the first programming write. To select the array block to be programmed, the program page buffers use BLOCK[7:0]. The data programmed in each array block is determined by the programming writes to the program buffer for each block. All program buffer data is unique whereas the program page offset address is shared by all blocks. An array block is selected for programming if the corresponding BLOCK bit is a 1. If BLOCK[M] = 1, then array block[M] is programmed. If BLOCK[M] = 0, then array block[M] is not programmed. The program page buffers are written regardless of the state of the BLOCK bits, but high-voltage is not applied to blocks for which BLOCK[M] = 0. Bits in the program page buffers select the non-programmed state if SES = 0. During a program margin read, the program buffers update bits to the non-programmed state for bits that correspond to array bits that the program margin read has determined are programmed. Technical Data 204 MMC2107 - Rev. 2.0 Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Functional Description 9.8 Functional Description The CMFR is an electrically erasable and programmable non-volatile memory. This subsection describes the functioning of the CMFR during various operational modes. Freescale Semiconductor, Inc... 9.8.1 Master Reset The device signals a master reset to the CMFR when a full reset is required. A master reset is the highest priority operation for the CMFR and terminates all other operations. The CMFR uses master reset to initialize all register bits to their default reset value. If the CMFR is in program or erase operation (EHV = 1) and a master reset is generated, the module performs the needed interlocks to disable the high voltage without damage to the high voltage circuits. Master reset terminates any other mode of operation and forces the CMFR BIU to a state ready to receive accesses. 9.8.2 Register Read and Write Operation The CMFR control registers are accessible for read or write operation at all times while the device is powered up except during master reset. The access time of a CMFR register is one system clock for both read and write accesses. Accesses to unimplemented registers causes the BIU to generate a data error exception. 9.8.3 Array Read Operation The CMFR array is available for read operation under most conditions while the device is powered up. Reads of the array are ignored (no response) during master reset or while the CMFR is disabled or in stop mode. During programming and erase operation while the high voltage is applied to the array (EHV = 1 or HVS = 1) the BIU generates data errors for all array accesses. At certain points, as defined in the program or erase sequence, reading the array results in a margin read. These margin reads return the status of the program or erase operation and not the data in the array. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com 205 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Non-Volatile Memory FLASH (CMFR) The type of array read is determined by comparing the address of the requested information with the address of the read page buffers. If the requested address is not in one of the read page buffers or if the read page buffer has been made invalid, an off-page read results. This read updates the selected array block's read page buffer address, copies the information from the array into the read page buffer, and drives a word/half-word onto the data bus. The off-page read requires a minimum of two clocks; margin off-page reads require additional clocks (see 9.8.4.2 Program Margin Reads and 9.8.5.2 Erase Margin Reads). If the address of the requested information is within the address ranges of either of the read page buffers, the second type of read is performed. This read is an on-page read and requires one clock to transfer information from the read page buffer onto the data bus. NOTE: After reset, programming writes, erase interlock write, setting EHV, clearing SES, setting/clearing SIE and exiting stop mode or disable mode, the page buffers do not contain valid information and the CMFR must do an off-page read before an on-page read can be done. 9.8.4 Programming To modify the charge stored in the isolated element of the CMFR bit from a logic 1 state to a logic 0 state, a programming operation is required. A programmed bit reads as logic 0. This programming operation applies the required voltages to change the charge state of the selected bits without changing the logic state of any other bits in the array. The program operation cannot change the logic 0 state to a logic 1 state; this transition must be done by the erase operation. An erased bit reads as logic 1. Programming uses a set of eight program buffers of 64 bytes to store the required data, an address offset buffer to store the starting address of the block(s) to be programmed, and a block select buffer that stores information on which block(s) are to be programmed. From one to eight of the program page buffers may be programmed at one time. CAUTION: Do not program any page more than once after a successful erase operation. While this does not physically damage the array it causes an increased partial disturb time for the unselected bits on the row and columns that are not programmed. A full erase of all blocks being programmed must be done before the CMFR can be used reliably. Technical Data 206 MMC2107 - Rev. 2.0 Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Functional Description Blocks of the CMFR that are protected (PROTECT[block] = 1) are not programmed. The program sequence is outlined in 9.8.4.1 Program Sequence and depicted in the flowchart form in Figure 9-7. 9.8.4.1 Program Sequence Freescale Semiconductor, Inc... Use this sequence to enable the high voltage to the array or shadow information for program operation: 1. Make sure the CMFRMTR and CMFRCTL are in their reset states. 2. Set PAWS[2] = 1 and GDB = 1 in CMFRMTR. 3. In CMFRMCR, write PROTECT[7:0] to disable protection of blocks to be programmed. 4. Use the procedure in Table 9-6 to write the pulse width timing control fields for a program pulse. 5. In CMFRCTL, clear the ERASE bit, and write BLOCK[7:0] to select the array blocks to be programmed. 6. In CMFRCTL, set the SES bit. 7. Programming write -- A successful write to the array locations to be programmed. This updates the programming page buffer(s) with the information to be programmed. All accesses to the array after the first write are to the same block offset address regardless of the address provided. Thus the locations accessed after the first programming write are limited to the page locations to be programmed. Off-page read accesses of the array after the first programming write are program margin reads. NOTE: All program page buffers share the same block offset address stored in the BIU. The block offset address is extracted from the address of the first programming write. To select the array block(s) to be programmed, the program page buffers use BLOCK[7:0]. Subsequent writes fill in the programming page buffers using the block address to select the program page buffer and the page word address to select the word in the page buffer. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com 207 Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) 8. In CMFRCTL, set the EHV bit. NOTE: If a program page buffer word has not received a programming write, no programming voltages are applied to the drain of the corresponding word in the array. At this point, writing to the program page buffers is disabled and causes a bus error until SES has been cleared and set. 9. Read CMFRCTL until HVS = 0. 10. In CMFRCTL, clear the EHV bit. Freescale Semiconductor, Inc... 11. Verify the program by reading the words of the pages that are being programmed. These are program margin reads. A bit that was successfully programmed returns a 0 during a margin read. It returns a 1 if it has been unsuccessfully programmed. If any bit intended to be programmed does not return a 0 after reading all the locations, the margin read has failed. If the margin read is successful continue to step 12, otherwise do the following: a. Write new pulse width parameters (if required, see Table 9-9 for the required programming algorithm) CLKPE and CLKPM. b. Write new values for PAWS and NVR (if required, see Table 9-9) c. Go back to step 8 to apply additional pulses. To reduce the time for verification, read two locations in each array block that is being programmed after reading a non-programmed bit. After a location has been verified (all bits are programmed), it is not necessary to reverify the location, as no further programming voltages are applied to the drain of the corresponding bits. CAUTION: After a program pulse, read at least one location with address bit 5 = 0 and one location with address bit 5 = 1 on each programmed page. Failure to do so may result in the loss of information in the CMFR array, and a full erase of all blocks being programmed must be done before the CMFR can be used reliably. 12. In CMFRCTL, clear the SES bit. 13. If more information needs to be programmed, go to step 3. Technical Data 208 MMC2107 - Rev. 2.0 Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Functional Description 1. MAKE SURE CMFRMTR AND CMFRCTL ARE IN THEIR RESET STATES 2. SET PAWS [2] = 1 AND GDB = 1 IN THE CMFRMTR 3. DISABLE PROTECTION OF THE BLOCKS TO BE PROGRAMMED PROTECT[7:0] IN CMFRMCR Freescale Semiconductor, Inc... 4. WRITE THE PULSE WIDTH TIMING CONTROL FIELDS FOR A PROGRAM PULSE (SEE TABLE 9-8) SCLKR[2:], CLKPE[1:], CLKPM[6:0] IN CMFRCTL 5. 6. 7. 8. SELECT PROGRAM OPERATION AND SELECT THE ARRAY BLOCK TO BE PROGRAMMED ERASE = 0, BLOCK[7:0] IN CMFRCTL CONFIGURE CMFR FOR PROGRAM OPERATION SES = 1 IN CMFRCTL WRITE 64 BYTES OF DATA TO THE LOCATION TO BE PROGRAMMED ENABLE HIGH-VOLTAGE PULSE FOR PROGRAMMING EHV = 1 IN CMFRCTL 9. NO 11a. 11b. 11c. UPDATE CLKPE, CLKPM, PAWS, AND NVR IF NEEDED PULSE APPLIED TO THE CMFR ARRAY BLOCK? HVS = 0 IN CMFRCTL YES 10. DISABLE HIGH-VOLTAGE PULSE EHV = 0 IN CMFRCTL FAILED 11. VERIFICATION PROCESS OK 12. END OF THE PROGRAMMING SEQUENCE SES = 0 IN CMFRCTL 13. YES PROGRAM NEXT PAGE? NO FINISH Notes: 1. This page program algorithm assumes the blocks to be programmed are initially erased. 2. Make sure that CMFRMTR is in its reset state at the beginning of the programming process and afterwards. Figure 9-7. FLASH Programming Flowchart MMC2107 - Rev. 2.0 MOTOROLA Technical Data Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com 209 Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) T3 S2 T1 RESET S3 T2 T6 T4 S1 S4 T7 Freescale Semiconductor, Inc... T8 T5 T9 S5 Figure 9-8. Program State Diagram Table 9-7. Program Interlock State Descriptions State Mode Next State S1 Normal operation: Normal array reads and register accesses. Block protect information and pulse width timing control can be modified. S2 T2 Write ERASE = 0 and SES = 1 S1 T1 Write SES = 0 or master reset S3 Hardware interlock: Successful programming write to any array location. Latches selected data word into programming page buffer; address latched to select location to program. Bit that has been written remains in program buffer until another write to it, or SES is cleared, or a program margin read T3 determines bit needs no modification by program operation. If write is to a register (except CMFRMCR), no data is stored in program page buffers, and CMFR remains in S2. Writing to CMFRMCR does not allow array to be programmed. S2 First program hardware interlock write: Normal read operation. Array accepts programming writes. Normal register accesses. CMFRCTL write cannot change EHV. If write is to a register other than CMFRMCR, no data is stored in program page buffers; CMFR remains in S2. Transition Requirement Technical Data 210 MMC2107 - Rev. 2.0 Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Functional Description Freescale Semiconductor, Inc... Table 9-7. Program Interlock State Descriptions (Continued) Next State Transition Requirement State Mode S1 T6 Write SES = 0 or master reset S3 Expanded program hardware interlock operation: Program margin reads. Programming writes accepted; all eight program pages can be programmed. Writes can be to any array location. Program page buffers updated using only data, lower address, and block address. Normal register accesses. CMFRCTL write can change EHV. If write is to a register, no data is stored in program page buffer. S4 T4 Write EHV = 1 Program operation: High voltage applied to array or shadow information to program CMFR bitcells. Pulse width timer active if SCLKR[2:0] 0; HVS can be polled to time program pulse. Programming writes not accepted. During programming, array cannot be accessed (bus error). Normal register accesses. CMFRCTL write can change only EHV. S1 T7 Master reset S5 T5 EHV = 0 and HVS = 0 Program margin read operation: Reads determine if bits on selected page need modification by program operation. Once bit is fully programmed, data stored in program page is updated; no further programming occurs for that bit and value read is 0. S4 T8 Write EHV = 1 S1 T9 Write SES = 0 or a master reset S4 S5 While it is not necessary to read all words on a page to determine if another program pulse is needed, all pages being programmed must be read once after each program pulse. 9.8.4.2 Program Margin Reads The CMFR provides a program margin read with electrical margin for the program state. Program margin reads provide sufficient margin to assure specified data retention. The program margin read is enabled when SE = 1 and a programming write has occurred. To increase the access time of the program margin read the off-page access time is 17 clocks instead of the usual 2-clock off-page read access time. The program margin read and subsequent on-page program verify reads MMC2107 - Rev. 2.0 MOTOROLA Technical Data Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com 211 Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) return a 1 for any bit that has not completely programmed. Bits left in the non-programmed state after the programming write read as a 0s. Bits that have completed programming read as 0s and update the data in the programming page buffer so that no further programming of those bits occurs. Freescale Semiconductor, Inc... Table 9-8. Results of Programming Margin Read Current Data in Program Page Buffer Current Bit State Read Output New Data for the Program Page Buffer 0 Programmed -- 0 0 1 0 Erased -- 1 1 0 1 Programmed -- 0 0 1 1 Erased -- 1 0 1 The program margin read occurs while doing the off-page read. A program margin read must be done for all pages that are being programmed after each program pulse. CAUTION: Failure to read each page that is being programmed after each program pulse may result in the loss of information in the array. While this does not physically damage the array a full erase of all blocks being programmed must be done before the CMFR can be used reliably. 9.8.4.3 Programming Shadow Information Programming the shadow information uses the same procedure as programming the array except that only program page 0 is used to program the shadow information. Before starting the program sequence SIE must be a 1. BLOCK and PROTECT bits do not affect programming of the shadow locations. Technical Data 212 MMC2107 - Rev. 2.0 Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Functional Description 9.8.4.4 Program Pulse-Width and Amplitude Modulation To prevent bits from possibly becoming depleted (over programmed), the first programming pulses should be of reduced duration and with reduced drain voltage. Refer to Table 9-9 for the required programming steps to insure FLASH reliability. Freescale Semiconductor, Inc... NOTE: The values of PAWS[2:0] and NVR should be updated on the appropriate pulse to change the programming voltage and CLKPM should be updated to adjust the pulse width. Table 9-9. Required Programming Algorithm Voltage Step PAWS[2:0] NVR Pulse Width Number of Pulses -2 V 100 1 250 s 4 -3 V 101 1 250 s 4 -4 V 110 1 250 s 4 -5 V 111 1 250 s 4 -6 V 100 0 50 s 20 -7 V 101 0 50 s 20 -8 V 110 0 50 s 20 -9 V 111 0 50 s 20 -9 V 111 0 100 s Any additional GDB = 1 for all programming operations. Margin reads are required after every pulse. 9.8.4.5 Overprogramming Programming a bit without a program margin read after each program pulse or exceeding the specified program times or voltages results in an overprogrammed state. Once a bit is overprogrammed, data in the array block that is located in the same column is lost as the overprogrammed bit causes the entire column to appear programmed. To restore an array block with an overprogrammed bit, the block must be erased and reprogrammed. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com 213 Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) 9.8.5 Erasing Freescale Semiconductor, Inc... To modify the charge stored in the isolated element of a bit from a logic 0 state to a logic 1 state, an erase operation is required. The erase operation cannot change the logic 1 state to a logic 0 state; this transition must be done by the program operation. Erase is a bulk operation that affects the stored charge of all the isolated elements in an array block. To make the block erasable, the array is divided into blocks that are physically isolated from each other. Each of the array blocks may be erased in isolation or in any combination. The array block size is fixed for all blocks at 16 Kbytes and the module is comprised of eight blocks. Array blocks that are protected (PROTECT[M] = 1) are not erased. The array blocks selected for erase operation are determined by BLOCK[7:0]. NOTE: Erasing BLOCK 0 also erases the shadow information. The erase sequence is outlined in 9.8.5.1 Erase Sequence and depicted in the flowchart form in Figure 9-9. Technical Data 214 MMC2107 - Rev. 2.0 Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Functional Description 9.8.5.1 Erase Sequence Use this sequence to enable the high voltage to the array or shadow information for erase operation: 1. Make sure that CMFRMTR is in its reset state, and write PAWS[2:0] = 111 to override firmware amplitude modulation. 2. In CMFRMCR, write PROTECT[7:0] to disable protection of the blocks to be erased. Freescale Semiconductor, Inc... 3. Use the procedure in Table 9-6 to write the pulse-width timing control fields for an erase pulse with BLOCK[7:0] selecting the blocks to be erased and ERASE = SES = 1 in CMFRCTL. 4. Execute an erase interlock write to any array location. 5. In CMFRCTL, write EHV = 1. 6. Read CMFRCTL until HVS = 0. 7. In CMFRCTL, write EHV = 0. 8. Verify the erase by reading all locations that are being erased, including the shadow information if the block that contains it is erased. Off-page reads are erase margin reads that update the read page buffer. If all the locations read as erased, continue to the next step otherwise, update PAWS and NVR (if required, see Table 9-9). Then go back to step 5. To reduce the time for verification, upon the first read of a 0, go to step 5. After a location has been verified (all bits are erased), it is not necessary to reverify locations after subsequent erase pulses. 9. In CMFRCTL, write SES = 0. 10. Make sure that CMFRMTR is in its reset state. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com 215 Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) 1. 2. 3.1. Freescale Semiconductor, Inc... 3.2. 3.3. 4. 5. OVERRIDE FIRMWARE AMPLITUDE MODULATION PAWS[2:0] = 111 IN CMFRMTR DISABLE PROTECTION OF THE BLOCKS TO BE ERASED PROTECT[7:0] IN CMFRMCR WRITE THE PULSE WIDTH TIMING CONTROL FIELDS FOR A ERASE PULSE (SEE TABLE 9-8) SCLKR[2:0], CLKPE[1:0], CLKPM[6:0] IN CMFRCTL SELECT ERASE OPERATION AND SELECT THE ARRAY BLOCK TO BE ERASED ERASE = 1, BLOCK[7:0] IN CMFRCTL CONFIGURE CMFR FOR PROGRAM OPERATION SES = 1 IN CMFRCTL EXECUTE AN ERASE INTERLOCK WRITE TO ANY ARRAY LOCATION TO BE ERASED ENABLE HIGH-VOLTAGE PULSE FOR ERASING EHV = 1 IN CMFRCTL 6. NO UPDATE PAWS AND NVR, IF REQUIRED YES 7. FAILED PULSE APPLIED TO THE CMFR ARRAY BLOCK? HVS = 0 IN CMFRCTL DISABLE HIGH-VOLTAGE PULSE EHV = 0 IN CMFRCTL 8. VERIFICATION PROCESS OK 9. END OF THE ERASING SEQUENCE SES = 0 IN CMFRCTL Note: Make sure that CMFRMTR is i its reset state at the beginning of the erasing process and afterwards. Figure 9-9. FLASH Erasing Flowchart Technical Data 216 MMC2107 - Rev. 2.0 Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Functional Description T3 S2 T1 RESET S3 T2 T6 T4 S1 S4 Freescale Semiconductor, Inc... T7 T5 T8 T9 S5 Figure 9-10. Erase State Diagram Table 9-10 Erase Interlock State Descriptions State Mode Next State S1 Normal operation: Normal array reads and register accesses. Block protect information and pulse-width timing control can be modified. S2 T2 Write ERASE = 1 and SES = 1 S1 T1 Write SES = 0 or a master reset S2 Erase hardware interlock write: Normal read operation. CMFR accepts erase hardware interlock write to any array location. Normal register access (except CMFRMCR). CMFRCTL write cannot set EHV. Register write (except CMFRMCR) is not erase hardware interlock write; CMFR remains in S2. CMFRMCR write causes transition to S3. S3 Hardware interlock: Write to any array location is erase interlock write. Register write other than CMFRMCR is not erase T3 hardware interlock write; CMFR remains in S2. CMFRMCR write causes transition to S3; NVM fuses cleared during high-voltage pulse Transition Requirement MMC2107 - Rev. 2.0 MOTOROLA Technical Data Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com 217 Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Freescale Semiconductor, Inc... Table 9-10 Erase Interlock State Descriptions (Continued) Next State Transition Requirement State Mode S1 T6 Write SES = 0 or a master reset S3 High voltage write enable: Erase margin reads occur. CMFR accepts erase hardware interlock write. Normal register accesses (except CMFRMCR). CMFRMCR write causes NVM fuses to be cleared during the high-voltage pulse. If CMFRMCR was written, a CMFRMCR read returns the NVM fuses value. CMFRCTL write can change EHV. When HVS goes high, NVR and PAWS are locked. S4 T4 Write EHV = 1 Erase operation: High voltage applied to array blocks to erase bitcells. Pulse-width timer active if SCLKR[2:0] 0; HVS can be polled to time the erase pulse. During erase, array cannot be accessed (bus error). Normal register accesses. CMFRCTL write can change only EHV. S1 T7 Master reset S5 T5 EHV = 0 and HVS = 0 Erase margin read operation: Reads determine if bits in selected blocks need modification by the erase operation. Erased bit reads as 1. All words in erased blocks must be read to determine if erase is complete. S4 T8 Write EHV = 1 S1 T9 Write SES = 0 or a master reset S4 S5 9.8.5.2 Erase Margin Reads The CMFR provides an erase margin read with electrical margin for the erase state. Erase margin reads provide sufficient margin to assure specified data retention. The erase margin read is enabled when SES = 1 and the erase write has occurred. The erase margin read and subsequent on-page erase verify reads return a 0 for any bit that has not completely erased. Bits that have completed erasing read as a 1s. To increase the access time of the erase margin read, the off-page access time is 17 clocks instead of the usual 2-clock off-page read access time. The erase margin read occurs while doing an off-page read. All locations within the block(s) that are being erased must read as a 1 to determine that no more erase pulses are required. Technical Data 218 MMC2107 - Rev. 2.0 Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) Functional Description 9.8.5.3 Erasing Shadow Information Words The shadow information words are erased with either array block 0 depending upon the array configuration. To verify that the shadow information words are erased with block 0, erase margin reads should be performed with the SIE bit set in CMFRMCR while the shadow information is read. For the erase operation to be completed, block 0 must also be fully verified. Freescale Semiconductor, Inc... NOTE: Setting SIE = 1 disables normal array access and should be cleared after verifying the shadow information. 9.8.6 Erase Pulse Amplitude and Width Modulation Refer to Table 9-11 for the required erase algorithm to insure reliability of the FLASH. NOTE: The values of PAWS[2:0] and NVR should be updated on the appropriate pulse to change the erase voltage. Table 9-11. Required Erase Algorithm Voltage Step PAWS[2:0] NVR Pulse Width Number of Pulses -2 V 100 1 100 ms 1 -3 V 101 1 100 ms 1 -4 V 110 1 100 ms 1 -5 V 111 1 100 ms 1 -6 V 100 0 100 ms 1 -7 V 101 0 100 ms 1 -8 V 110 0 100 ms 1 -9 V 111 0 100 ms 20 GDB = 0 for all erase operations. Margin reads are required after the first -9-V pulse. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com 219 Freescale Semiconductor, Inc. Non-Volatile Memory FLASH (CMFR) 9.8.7 Emulation Operation Freescale Semiconductor, Inc... In emulation mode, to support emulation of the internal FLASH memory with external memory devices, the CMFR responds to an array access only by terminating the access. During emulation, the CMFR does not drive any data and the data should be provided by an external device. This synchronizes the timing of 1-clock on-page accesses and 2-clock off-page accesses during emulation from external memory. 9.9 Master Reset The device signals a master reset to the CMFR when a full reset is required. A master reset is the highest priority operation for the CMFR and terminates all other operations. The CMFR uses master reset to initialize all register bits to their default reset value. If the CMFR is in program or erase operation (EHV = 1) and a master reset is generated, the module performs the needed interlocks to disable the high voltage without damage to the high voltage circuits. Master reset terminates any other mode of operation and forces the CMFR BIU to a state ready to receive accesses. 9.10 Interrupts The CMFR does not generate interrupt requests. Technical Data 220 MMC2107 - Rev. 2.0 Non-Volatile Memory FLASH (CMFR) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 10. Clock Module Freescale Semiconductor, Inc... 10.1 Contents 10.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222 10.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222 10.4 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .223 10.4.1 Normal PLL Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 10.4.2 1:1 PLL Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 10.4.3 External Clock Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 10.4.4 Low-Power Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 10.4.4.1 Wait and Doze Modes . . . . . . . . . . . . . . . . . . . . . . . . . . 223 10.4.4.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 10.5 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 10.6 Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .225 10.6.1 EXTAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 10.6.2 XTAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 10.6.3 CLKOUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 10.6.4 VDDSYN and VSSSYN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 10.6.5 RSTOUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226 10.7 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 226 10.7.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226 10.7.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 10.7.2.1 Synthesizer Control Register . . . . . . . . . . . . . . . . . . . . . 227 10.7.2.2 Synthesizer Status Register. . . . . . . . . . . . . . . . . . . . . . 230 10.7.2.3 Synthesizer Test Register . . . . . . . . . . . . . . . . . . . . . . .233 10.7.2.4 Synthesizer Test Register 2 . . . . . . . . . . . . . . . . . . . . . . 234 10.8 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235 10.8.1 System Clock Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235 10.8.2 System Clocks Generation. . . . . . . . . . . . . . . . . . . . . . . . . 236 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Clock Module For More Information On This Product, Go to: www.freescale.com 221 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Clock Module 10.8.3 10.8.3.1 10.8.3.2 10.8.4 10.8.4.1 10.8.4.2 10.8.5 10.8.6 10.8.6.1 10.8.6.2 10.8.6.3 10.8.6.4 10.9 PLL Lock Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236 PLL Loss of Lock Conditions . . . . . . . . . . . . . . . . . . . . . 238 PLL Loss of Lock Reset . . . . . . . . . . . . . . . . . . . . . . . . . 238 Loss of Clock Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . 238 Alternate Clock Selection . . . . . . . . . . . . . . . . . . . . . . . . 239 Loss-of-Clock Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . .242 Clock Operation During Reset . . . . . . . . . . . . . . . . . . . . . . 243 PLL Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243 Phase and Frequency Detector (PFD). . . . . . . . . . . . . .245 Charge Pump/Loop Filter . . . . . . . . . . . . . . . . . . . . . . . . 245 Voltage Control Output (VCO) . . . . . . . . . . . . . . . . . . . . 246 Multiplication Factor Divider (MFD) . . . . . . . . . . . . . . . . 246 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246 10.10 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246 10.2 Introduction The clock module contains: * Crystal oscillator (OSC) * Phase-locked loop (PLL) * Reduced frequency divider (RFD) * Status and control registers * Control logic To improve noise immunity, the PLL and OSC have their own power supply pins, VDDSYN and VSSSYN. All other circuits are powered by the normal internal supply pins, VDD and VSS. 10.3 Features Features of the clock module include: * 2- to 10-MHz reference crystal * Support for low-power modes * Separate clock out signal Technical Data 222 MMC2107 - Rev. 2.0 Clock Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Clock Module Modes of Operation 10.4 Modes of Operation The clock module can be operated in normal PLL mode, 1:1 PLL mode, or external clock mode. Freescale Semiconductor, Inc... 10.4.1 Normal PLL Mode In normal PLL mode, the PLL is fully programmable. It can synthesize frequencies ranging from 2x to 9x the reference frequency and has a post divider capable of reducing this synthesized frequency without disturbing the PLL. The PLL reference can be either a crystal oscillator or an external clock. 10.4.2 1:1 PLL Mode In 1:1 PLL mode, the PLL synthesizes a frequency equal to the external clock input reference frequency. The post divider is not active. 10.4.3 External Clock Mode In external clock mode, the PLL is bypassed, and the external clock is applied to EXTAL. 10.4.4 Low-Power Options During wakeup from a low-power mode, the FLASH clock always clocks through at least 16 cycles before the core clocks are enabled. This allows the FLASH module time to recover from the low-power mode, and software can immediately resume fetching instructions from the flash memory. 10.4.4.1 Wait and Doze Modes In wait and doze modes, the system clocks to the peripherals are enabled, and the clocks to the CPU, FLASH, and random-access memory (RAM) are stopped. Each module can disable the module clocks locally at the module level. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Clock Module For More Information On This Product, Go to: www.freescale.com 223 Freescale Semiconductor, Inc. Clock Module 10.4.4.2 Stop Mode Freescale Semiconductor, Inc... In stop mode, all system clocks are disabled. There are several options for enabling/disabling the PLL and/or crystal oscillator in stop mode at the price of increased wakeup recovery time. The PLL can be disabled in stop mode, but then it requires a wakeup period before it can relock. The OSC can also be disabled during stop mode, but then it requires a wakeup period to restart. When the PLL is enabled in stop mode (STPMD[1:0]), the external CLKOUT signal can support systems using CLKOUT as the clock source. There is also a fast wakeup option for quickly enabling the system clocks during stop recovery. This eliminates the wakeup recovery time but at a price of sending a potentially unstable clock to the system. To prevent a non-locked PLL frequency overshoot when using the fast wakeup option, change the RFD divisor to the current RFD value plus one before entering stop mode. In external clock mode, there are no wakeup periods for oscillator startup or PLL lock. 10.5 Block Diagram EXTAL XTAL OSCILLATOR VDDSYN VSSSYN REFERENCE CLOCK RSTOUT VCO CLKOUT RFD PLL CLKOUT CLKGEN INTERNAL CLOCKS DISCLK Figure 10-1. Clock Module Block Diagram Technical Data 224 MMC2107 - Rev. 2.0 Clock Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Clock Module Signal Descriptions 10.6 Signal Descriptions The clock module signals are summarized in Table 10-1 and a brief description follows. For more detailed information, refer to Section 4. Signal Description. Table 10-1. Signal Properties Freescale Semiconductor, Inc... Name Function EXTAL Oscillator or clock input XTAL Oscillator output CLKOUT System clock output VDDSYN Clock module power supply inputs VSSSYN RSTOUT Reset signal from reset controller 10.6.1 EXTAL This input is driven by an external clock except when used as a connection to the external crystal when using the internal oscillator. 10.6.2 XTAL This output is an internal oscillator connection to the external crystal. 10.6.3 CLKOUT This output reflects the internal system clock. 10.6.4 VDDSYN and VSSSYN These are dedicated power and ground inputs for the frequency synthesizer. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Clock Module For More Information On This Product, Go to: www.freescale.com 225 Freescale Semiconductor, Inc. Clock Module 10.6.5 RSTOUT The RSTOUT pin is asserted by: * Internal system reset signal, or * FRCRSTOUT bit in the reset control status register (RCR); see 5.6.1 Reset Control Register Freescale Semiconductor, Inc... 10.7 Memory Map and Registers The clock programming model consists of these registers: * Synthesizer control register (SYNCR) -- Defines clock operation * Synthesizer status register (SYNSR) -- Reflects clock status * Synthesizer test register (SYNTR) -- Used for factory test * Synthesizer test register 2 (SYNTR2) -- Used only for factory test 10.7.1 Module Memory Map Table 10-2. Clock Module Memory Map Address Register Name Access(1) 0x00c3_0000 Synthesizer control register (SYNCR) S 0x00c3_0002 Synthesizer status register (SYNSR) S 0x00c3_0003 Synthesizer test register (SYNTR) S 0x00c3_0004 Synthesizer test register 2 (SYNTR2) S 1. S = CPU supervisor mode access only. Technical Data 226 MMC2107 - Rev. 2.0 Clock Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Clock Module Memory Map and Registers 10.7.2 Register Descriptions This subsection provides a description of the clock module registers. 10.7.2.1 Synthesizer Control Register The synthesizer control register (SYNCR) is read/write always. Freescale Semiconductor, Inc... Address: 0x00c3_0000 and 0x00c3_0001 Bit 15 14 13 12 11 10 9 Bit 8 LOLRE MFD2 MFD1 MFD0 LOCRE RFD2 RFD1 RFD0 0 0 1 0 0 0 0 1 Bit 7 6 5 4 3 2 1 Bit 0 LOCEN DISCLK FWKUP RSVD4 STMPD1 STMPD0 RSVD1 RSVD0 0 0 0 0 0 0 0 0 Read: Write: Reset: Read: Write: Reset: Figure 10-2. Synthesizer Control Register (SYNCR) LOLRE -- Loss of Lock Reset Enable Bit The LOLRE bit determines how the system handles a loss of lock indication. When operating in normal mode or 1:1 PLL mode, the PLL must be locked before setting the LOLRE bit. Otherwise reset is immediately asserted. To prevent an immediate reset, the LOLRE bit must be cleared before writing the MFD[2:0] bits or entering stop mode with the PLL disabled. 1 = Reset on loss of lock 0 = No reset on loss of lock NOTE: In external clock mode, the LOLRE bit has no effect. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Clock Module For More Information On This Product, Go to: www.freescale.com 227 Freescale Semiconductor, Inc. Clock Module MFD[2:0] -- Multiplication Factor Divider Field MFD[2:0] contain the binary value of the divider in the PLL feedback loop. See Table 10-3. The MFD[2:0] value is the multiplication factor applied to the reference frequency. When MFD[2:0] are changed or the PLL is disabled in stop mode, the PLL loses lock. In 1:1 PLL mode, MFD[2:0] are ignored, and the multiplication factor is one. Freescale Semiconductor, Inc... NOTE: In external clock mode, the MFD[2:0] bits have no effect. See Table 10-6. Table 10-3. System Frequency Multiplier of the Reference Frequency(1) in Normal PLL Mode RFD[2:0] MFD[2:0] 000 (2x) 001 (3x) 010 (4x) 011 (5x) 100 (6x) 101 (7x) 110 (8x) 111 (9x) 000 (/ 1) 2 3 4 5 6 7 8 9 001 (/ 2)(2) 1 3/2 2 5/2 3 7/2 4 9/2 010 (/ 4) 1/2 3/4 1 5/4 3/2 7/4 2 9/4 011 (/ 8) 1/4 3/8 1/2 5/8 3/4 7/8 1 9/8 100 (/ 16) 1/8 3/16 1/4 5/16 3/8 7/16 1/2 9/16 101 (/ 32) 1/16 3/32 1/8 5/32 3/16 7/32 1/4 9/32 110 (/ 64) 1/32 3/64 1/16 5/64 3/32 7/64 1/8 9/64 111 (/ 128) 1/64 3/128 1/32 5/128 3/64 7/128 1/16 9/128 1. fsys = fref x (MFD + 2)/2RFD 2. Default value out of reset LOCRE -- Loss of Clock Reset Enable Bit The LOCRE bit determines how the system handles a loss of clock condition. When the LOCEN bit is clear, LOCRE has no effect. If the LOCS flag in SYNSR indicates a loss of clock condition, setting the LOCRE bit causes an immediate reset. To prevent an immediate reset, the LOCRE bit must be cleared before entering stop mode with the PLL disabled. 1 = Reset on loss of clock 0 = No reset on loss of clock NOTE: In external clock mode, the LOCRE bit has no effect. Technical Data 228 MMC2107 - Rev. 2.0 Clock Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Clock Module Memory Map and Registers RFD[2:0] -- Reduced Frequency Divider Field The binary value written to RFD[2:0] is the PLL frequency divisor. See Table 10-3. Changing RFD[2:0] does not affect the PLL or cause a relock delay. Changes in clock frequency are synchronized to the next falling edge of the current system clock. To avoid surpassing the allowable system operating frequency, write to RFD[2:0] only when the LOCK bit is set. Freescale Semiconductor, Inc... NOTE: In external clock mode, the RFD[2:0] bits have no effect. See Table 10-6. LOCEN -- Loss of Clock Enable Bit The LOCEN bit enables the loss of clock function. LOCEN does not affect the loss of lock function. 1 = Loss of clock function enabled 0 = Loss of clock function disabled NOTE: In external clock mode, the LOCEN bit has no effect. DISCLK -- Disable CLKOUT Bit The DISCLK bit determines whether CLKOUT is driven. Setting the DISCLK bit holds CLKOUT low. 1 = CLKOUT disabled 0 = CLKOUT enabled FWKUP -- Fast Wakeup Bit The FWKUP bit determines when the system clocks are enabled during wakeup from stop mode. 1 = System clocks enabled on wakeup regardless of PLL lock status 0 = System clocks enabled only when PLL is locked or operating normally NOTE: When FWKUP = 0, if the PLL or OSC is enabled and unintentionally lost in stop mode, the PLL wakes up in self-clocked mode or reference clock mode depending on the clock that was lost. In external clock mode, the FWKUP bit has no effect on the wakeup sequence. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Clock Module For More Information On This Product, Go to: www.freescale.com 229 Freescale Semiconductor, Inc. Clock Module STPMD[1:0] -- Stop Mode Bits STPMD[1:0] control PLL and CLKOUT operation in stop mode as shown in Table 10-4. Table 10-4. STPMD[1:0] Operation in Stop Mode Operation During Stop Mode Freescale Semiconductor, Inc... STPMD[1:0] System Clocks PLL OSC CLKOUT 00 Disabled Enabled Enabled Enabled 01 Disabled Enabled Enabled Disabled 10 Disabled Disabled Enabled Disabled 11 Disabled Disabled Disabled Disabled RSVD4, RSVD1, and RSVD0 -- Reserved Writing to these read/write bits updates their values but has no effect on functionality. 10.7.2.2 Synthesizer Status Register The synthesizer status register (SYNSR) is a read-only register that can be read at any time. Writing to the SYNSR has no effect and terminates the cycle normally. Address: 0x00c3_0002 Bit 7 Read: PLLMODE 6 5 4 3 2 1 Bit 0 PLLSEL PLLREF LOCKS LOCK LOCS 0 0 Note 1 Note 1 Note 2 Note 2 0 0 0 Write: Reset: Note 1 = Writes have no effect and the access terminates without a transfer error exception. Notes: 1. Reset state determined during reset configuration. 2. See the LOCKS and LOCK bit descriptions. Figure 10-3. Synthesizer Status Register (SYNSR) Technical Data 230 MMC2107 - Rev. 2.0 Clock Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Clock Module Memory Map and Registers PLLMODE -- Clock Mode Bit The MODE bit is configured at reset and reflects the clock mode as shown in Table 10-5. 1 = PLL clock mode 0 = External clock mode Table 10-5. System Clock Modes Freescale Semiconductor, Inc... MODE:PLLSEL:PLLREF Clock Mode 000 External clock mode 100 1:1 PLL mode 110 Normal PLL mode with external clock reference 111 Normal PLL mode with crystal oscillator reference PLLSEL -- PLL Select Bit The PLLSEL bit is configured at reset and reflects the PLL mode as shown in Table 10-5. 1 = Normal PLL mode 0 = 1:1 PLL mode PLLREF -- PLL Reference Bit The PLLREF bit is configured at reset and reflects the PLL reference source in normal PLL mode as shown in Table 10-5. 1 = Crystal clock reference 0 = External clock reference LOCKS -- Sticky PLL Lock Bit The LOCKS flag is a sticky indication of PLL lock status. 1 = No unintentional PLL loss of lock since last system reset or MFD change 0 = PLL loss of lock since last system reset or MFD change or currently not locked due to exit from STOP with FWKUP set The lock detect function sets the LOCKS bit when the PLL achieves lock after: - A system reset, or - A write to SYNCR that changes the MFD[2:0] bits When the PLL loses lock, LOCKS is cleared. When the PLL relocks, LOCKS remains cleared until one of the two listed events occurs. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Clock Module For More Information On This Product, Go to: www.freescale.com 231 Freescale Semiconductor, Inc. Clock Module In stop mode, if the PLL is intentionally disabled, then the LOCKS bit reflects the value prior to entering stop mode. However, if FWKUP is set, then LOCKS is cleared until the PLL regains lock. Once lock is regained, the LOCKS bit reflects the value prior to entering stop mode. Furthermore, reading the LOCKS bit at the same time that the PLL loses lock does not return the current loss of lock condition. In external clock mode, LOCKS remains cleared after reset. In normal PLL mode and 1:1 PLL mode, LOCKS is set after reset. Freescale Semiconductor, Inc... LOCK -- PLL Lock Flag 1 = PLL locked 0 = PLL not locked The LOCK flag is set when the PLL is locked. PLL lock occurs when the synthesized frequency is within approximately 0.75 percent of the programmed frequency. The PLL loses lock when a frequency deviation of greater than approximately 1.5 percent occurs. Reading the LOCK flag at the same time that the PLL loses lock or acquires lock does not return the current condition of the PLL. The power-on reset circuit uses the LOCK bit as a condition for releasing reset. If operating in external clock mode, LOCK remains cleared after reset. LOCS -- Sticky Loss Of Clock Flag 1 = Loss of clock detected since exiting reset or oscillator not yet recovered from exit from stop mode with FWKUP = 1 0 = Loss of clock not detected since exiting reset The LOCS flag is a sticky indication of whether a loss of clock condition has occurred at any time since exiting reset in normal PLL and 1:1 PLL modes. LOCS = 0 when the system clocks are operating normally. LOCS = 1 when system clocks have failed due to a reference failure or PLL failure. After entering stop mode with FWKUP set and the PLL and oscillator intentionally disabled (STPMD[1:0] = 11), the PLL exits stop mode in SCM while the oscillator starts up. During this time, LOCS is temporarily set regardless of LOCEN. It is cleared once the oscillator comes up and the PLL is attempting to lock. If a read of the LOCS flag and a loss of clock condition occur simultaneously, the flag does not reflect the current loss of clock condition. Technical Data 232 MMC2107 - Rev. 2.0 Clock Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Clock Module Memory Map and Registers A loss of clock condition can be detected only if LOCEN = 1 or the oscillator has not yet returned from exit from stop mode with FWKUP = 1. NOTE: The LOCS flag is always 0 in external clock mode. 10.7.2.3 Synthesizer Test Register Freescale Semiconductor, Inc... The synthesizer test register (SYNTR) is only for factory testing. When not in test mode, SYNTR is read-only. Address: 0x00c3_0003 Read: Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 10-4. Synthesizer Test Register (SYNTR) MMC2107 - Rev. 2.0 MOTOROLA Technical Data Clock Module For More Information On This Product, Go to: www.freescale.com 233 Freescale Semiconductor, Inc. Clock Module 10.7.2.4 Synthesizer Test Register 2 The synthesizer test register 2 (SYNTR2) is only for factory testing. Address: 0x00c3_0004 through 0x00c3_0007 Read: Bit 31 30 29 28 27 26 25 Bit 24 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 23 22 21 20 19 18 17 Bit 16 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 RSVD9 RSVD8 Write: Freescale Semiconductor, Inc... Reset: Read: Write: Reset: Read: Write: Reset: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 RSVD7 RSVD6 RSVD5 RSVD4 RSVD3 RSVD2 RSVD1 RSVD0 0 0 0 0 0 0 0 0 Read: Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 10-5. Synthesizer Test Register 2 (SYNTR2) Bits 31-10 Bits 31-10 are read-only. Writing to bits 31-10 has no effect. RSVD9-RSVD0 -- Reserved The RSVD bits can be read at any time. Writes to these bits update the register values but have no effect on functionality. Technical Data 234 MMC2107 - Rev. 2.0 Clock Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Clock Module Functional Description 10.8 Functional Description This subsection provides a functional description of the clock module. Freescale Semiconductor, Inc... 10.8.1 System Clock Modes The system clock source is determined during reset. The value of VDDSYN is latched during reset and is expected to remain at that state after reset is negated. If VDDSYN is changed during a reset other than power-on reset, the internal clocks may glitch as the clock source is changed between external clock mode and PLL clock mode. Whenever VDDSYN is changed in reset, an immediate loss of lock condition occurs. Table 10-6 shows the clock-out frequency to clock-in frequency relationships for the possible clock modes. Table 10-6. Clock-Out and Clock-In Relationships PLL Options(1) Clock Mode Normal PLL clock mode fsys = fref x (MFD + 2)/2RFD 1:1 PLL clock mode fsys = fref External clock mode fsys = fref/2 1. fref = input reference frequency fsys = CLKOUT frequency MFD ranges from 0 to 7. RFD ranges from 0 to 7. CAUTION: XTAL must be tied low in external clock mode when reset is asserted. If it is not, clocks could be suspended indefinitely. The external clock is divided by two internally to produce the system clocks. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Clock Module For More Information On This Product, Go to: www.freescale.com 235 Freescale Semiconductor, Inc. Clock Module 10.8.2 System Clocks Generation In normal PLL clock mode, the default system frequency is two times the reference frequency after reset. The RFD[2:0] and MFD[2:0] bits in SYNCR select the frequency multiplier. Freescale Semiconductor, Inc... When programming the PLL, do not exceed the maximum system clock frequency listed in the electrical specifications. Use this procedure to accommodate the frequency overshoot that occurs when the MFD bits are changed: 1. Determine the appropriate value for the MFD and RFD fields in SYNCR. The amount of jitter in the system clocks can be minimized by selecting the maximum MFD factor that can be paired with an RFD factor to provide the required frequency. 2. Write a value of RFD (from step 1) + 1 to the RFD field of SYNCR. 3. Write the MFD value from step 1 to SYNCR. 4. Monitor the LOCK flag in SYNSR. When the PLL achieves lock, write the RFD value from step 1 to the RFD field of SYNCR. This changes the system clocks frequency to the required frequency. NOTE: Keep the maximum system clock frequency below the limit given in Section 22. Electrical Specifications. 10.8.3 PLL Lock Detection The lock detect logic monitors the reference frequency and the PLL feedback frequency to determine when frequency lock is achieved. Phase lock is inferred by the frequency relationship, but is not guaranteed. The LOCK flag in SYNSR reflects the PLL lock status. A sticky lock flag, LOCKS, is also provided. The lock detect function uses two counters. One is clocked by the reference and the other is clocked by the PLL feedback. When the reference counter has counted N cycles, its count is compared to that of the feedback counter. If the feedback counter has also counted N cycles, the process is repeated for N + K counts. Then, if the two counters still match, the lock criteria is relaxed by 1/2 and the system is notified that the PLL has achieved frequency lock. Technical Data 236 MMC2107 - Rev. 2.0 Clock Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Clock Module Functional Description After lock is detected, the lock circuit continues to monitor the reference and feedback frequencies using the alternate count and compare process. If the counters do not match at any comparison time, then the LOCK flag is cleared to indicate that the PLL has lost lock. At this point, the lock criteria is tightened and the lock detect process is repeated. Freescale Semiconductor, Inc... The alternate count sequences prevent false lock detects due to frequency aliasing while the PLL tries to lock. Alternating between tight and relaxed lock criteria prevents the lock detect function from randomly toggling between locked and non-locked status due to phase sensitivities. Figure 10-6 shows the sequence for detecting locked and non-locked conditions. In external clock mode, the PLL is disabled and cannot lock. START WITH TIGHT LOCK CRITERIA LOSS OF LOCK DETECTED SET TIGHT LOCK CRITERIA AND NOTIFY SYSTEM OF LOSS OF LOCK CONDITION REFERENCE COUNT REFERENCE COUNT FEEDBACK COUNT FEEDBACK COUNT COUNT N REFERENCE CYCLES AND COMPARE NUMBER OF FEEDBACK CYCLES ELAPSED REFERENCE COUNT = FEEDBACK COUNT = N IN SAME COUNT/COMPARE SEQUENCE LOCK DETECTED. SET RELAXED LOCK CONDITION AND NOTIFY SYSTEM OF LOCK CONDITION COUNT N + K REFERENCE CYCLES AND COMPARE NUMBER OF FEEDBACK CYCLES ELAPSED REFERENCE COUNT = FEEDBACK COUNT = N + K IN SAME COUNT/COMPARE SEQUENCE Figure 10-6. Lock Detect Sequence MMC2107 - Rev. 2.0 MOTOROLA Technical Data Clock Module For More Information On This Product, Go to: www.freescale.com 237 Freescale Semiconductor, Inc. Clock Module 10.8.3.1 PLL Loss of Lock Conditions Freescale Semiconductor, Inc... Once the PLL acquires lock after reset, the LOCK and LOCKS flags are set. If the MFD is changed, or if an unexpected loss of lock condition occurs, the LOCK and LOCKS flags are negated. While the PLL is in the non-locked condition, the system clocks continue to be sourced from the PLL as the PLL attempts to relock. Consequently, during the relocking process, the system clocks frequency is not well defined and may exceed the maximum system frequency, violating the system clock timing specifications. However, once the PLL has relocked, the LOCK flag is set. The LOCKS flag remains cleared if the loss of lock is unexpected. The LOCKS flag is set when the loss of lock is caused by changing MFD. If the PLL is intentionally disabled during stop mode, then after exit from stop mode, the LOCKS flag reflects the value prior to entering stop mode once lock is regained. 10.8.3.2 PLL Loss of Lock Reset If the LOLRE bit in SYNCR is set, a loss of lock condition asserts reset. Reset reinitializes the LOCK and LOCKS flags. Therefore, software must read the LOL bit in reset status register (RSR) to determine if a loss of lock caused the reset. See 5.6.2 Reset Status Register. To exit reset in PLL mode, the reference must be present, and the PLL must achieve lock. In external clock mode, the PLL cannot lock. Therefore, a loss of lock condition cannot occur, and the LOLRE bit has no effect. 10.8.4 Loss of Clock Detection The LOCEN bit in SYNCR enables the loss of clock detection circuit to monitor the input clocks to the phase and frequency detector (PFD). When either the reference or feedback clock frequency falls below the minimum frequency, the loss of clock circuit sets the sticky LOCS flag in SYNSR. NOTE: In external clock mode, the loss of clock circuit is disabled. Technical Data 238 MMC2107 - Rev. 2.0 Clock Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Clock Module Functional Description 10.8.4.1 Alternate Clock Selection Freescale Semiconductor, Inc... Depending on which clock source fails, the loss-of-clock circuit switches the system clocks source to the remaining operational clock. The alternate clock source generates the system clocks until reset is asserted. As Table 10-7 shows, if the reference fails, the PLL goes out of lock and into self-clocked mode (SCM). The PLL remains in SCM until the next reset. When the PLL is operating in SCM, the system frequency depends on the value in the RFD field. The SCM system frequency stated in electrical specifications assumes that the RFD has been programmed to binary 000. If the loss-of-clock condition is due to PLL failure, the PLL reference becomes the system clocks source until the next reset, even if the PLL regains and relocks. Table 10-7. Loss of Clock Summary Clock Mode System Clock Source Before Failure Reference Failure Alternate Clock Selected by LOC Circuit(1) Until Reset PLL Failure Alternate Clock Selected by LOC Circuit Until Reset PLL PLL PLL self-clocked mode PLL reference External External clock None NA 1. The LOC circuit monitors the reference and feedback inputs to the PFD. See Figure 10-8. A special loss-of-clock condition occurs when both the reference and the PLL fail. The failures may be simultaneous, or the PLL may fail first. In either case, the reference clock failure takes priority and the PLL attempts to operate in SCM. If successful, the PLL remains in SCM until the next reset. If the PLL cannot operate in SCM, the system remains static until the next reset. Both the reference and the PLL must be functioning properly to exit reset. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Clock Module For More Information On This Product, Go to: www.freescale.com 239 Freescale Semiconductor, Inc. Clock Module Freescale Semiconductor, Inc... FWKUP X X X X X X -- NRM 0 0 LOCS OSC EXT LOCK PLL Expected PLL Action at Stop LOCKS MODE In LOCEN LOCRE LOLRE Table 10-8. Stop Mode Operation (Sheet 1 of 3) -- EXT 0 0 0 Lose reference clock Stuck -- -- -- NRM `LK 1 `LC Stuck -- -- -- PLL Action During Stop Regain Lose lock, 0 Off Off 0 f.b. clock, reference clock No regain Regain clocks, but don't regain lock NRM NRM X 0 0 0 Lose lock, 0 Off Off 1 f.b. clock, reference clock 0 Off On 0 Lose lock 0 0 0 Off On 1 Lose lock SCM-> unstable NRM 0 On On 0 -- 0-> 1-> No f.b. clock regain Stuck -- -- -- Regain NRM `LK 1 `LC Lose reference clock or no lock regain Stuck -- -- -- Lose reference clock, NRM regain `LK 1 `LC Block LOCKS from being cleared `LC Block LOCKS until lock regained Unstable NRM Lose reference clock Stuck or no f.b. clock regain 0 0 0 On On 1 -- 0->`LK 0->1 -- -- 0->`LK 0->1 240 `LC `LK 1 `LC Lose lock or clock Stuck -- -- -- Lose lock, regain NRM 0 1 `LC Lose clock and lock, regain NRM 0 1 `LC NRM `LK 1 `LC 0 0->1 `LC Lose lock Unstable NRM Lose lock, regain NRM 0 1 `LC Lose clock Stuck -- -- -- Lose clock, regain without lock Unstable NRM 0 0->1 `LC Lose clock, regain with lock NRM 0 1 `LC Technical Data Block LOCKS from being cleared -- NRM -- NRM Block LOCS and LOCKS until clock and lock respectively regain; enter SCM regardless of LOCEN bit 0-> -- 0 0 Block LOCS and LOCKS until clock and lock respectively 0->`LK 0->1 1->`LC regain; enter SCM regardless of LOCEN bit until reference regained SCM-> Lose reference clock, Unstable NRM regain NRM Comments No reference clock regain No lock regain NRM MODE Out LOCS not set because LOCEN = 0 LOCS not set because LOCEN = 0 MMC2107 - Rev. 2.0 Clock Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Clock Module Functional Description FWKUP X Lose lock, X f.b. clock, RESET reference clock NRM 0 0 1 On On X 1 0 Lose lock, Regain 0 Off Off 0 f.b. clock, reference clock No regain Freescale Semiconductor, Inc... NRM NRM NRM NRM NRM NRM NRM 1 0 1 0 1 0 1 0 1 0 0 Off On 0 0 Off On 1 0 On On 0 0 On On 1 1 On On X 1 1 X Off X -- Lose lock, f.b. clock Lose lock, f.b. clock -- -- -- LOCS OSC X X 1 Off LOCK PLL NRM Expected PLL Action at Stop LOCKS MODE In LOCEN LOCRE LOLRE Table 10-8. Stop Mode Operation (Sheet 2 of 3) RESET -- -- -- NRM `LK 1 `LC RESET -- -- -- Reset immediately NRM `LK 1 `LC REF not entered during stop; SCM entered during stop only during OSC startup Stuck -- -- -- Regain NRM `LK 1 `LC No f.b. clock or lock regain Stuck -- -- -- Lose reference clock SCM 0 0 1 Regain f.b. clock Unstable NRM No f.b. clock regain Stuck -- -- -- Lose reference clock SCM 0 0 1 -- NRM `LK 1 `LC Lose reference clock SCM 0 0 1 Wakeup without lock Wakeup without lock PLL Action During Stop -- Lose lock or clock 1 1 -- REF mode not entered during stop Wakeup without lock REF mode not entered during stop Wakeup without lock REF 0 X 1 Stuck -- -- -- Lose lock, regain NRM 0 1 `LC -- NRM `LK 1 `LC Lose reference clock SCM 0 0 1 Wakeup without lock Lose f.b. clock REF 0 X 1 Wakeup without lock Lose lock Unstable NRM 0 0->1 `LC NRM `LK 1 `LC RESET -- -- -- Reset immediately RESET -- -- -- Reset immediately NRM `LK 1 `LC Lose clock RESET -- -- -- Lose lock Stuck -- -- -- Lose lock, regain NRM 0 1 `LC -- Lose lock or clock MMC2107 - Rev. 2.0 MOTOROLA `LC Reset immediately Lose lock Lose lock, X f.b. clock, RESET reference clock 0 On On 0 0->`LK 0->1 Comments Lose f.b. clock -- NRM MODE Out Reset immediately Technical Data Clock Module For More Information On This Product, Go to: www.freescale.com 241 Freescale Semiconductor, Inc. Clock Module LOCK LOCS Expected PLL Action at Stop LOCKS FWKUP OSC PLL MODE In LOCEN LOCRE LOLRE Table 10-8. Stop Mode Operation (Sheet 3 of 3) NRM `LK 1 `LC Lose clock RESET -- -- -- Lose lock Unstable NRM 0 0->1 `LC NRM 0 1 `LC NRM `LK 1 `LC RESET -- -- -- REF 0 X 1 PLL Action During Stop -- NRM 1 1 0 On On 1 -- Freescale Semiconductor, Inc... Lose lock, regain -- MODE Out NRM 1 1 1 On On X -- REF 1 0 0 X X X -- Lose reference clock Stuck -- -- -- SCM 1 0 0 Off X 0 PLL disabled Regain SCM SCM 0 0 1 SCM 1 0 0 Off X 1 PLL disabled Regain SCM SCM 0 0 1 SCM 1 0 0 On On 0 -- -- SCM Lose reference clock SCM 0 0 1 SCM 1 0 0 On On 1 -- -- SCM Lose reference clock SCM 0 0 1 Lose clock or lock -- Comments Reset immediately Reset immediately Wakeup without lock Wakeup without lock PLL = PLL enabled during STOP mode. PLL = On when STPMD[1:0] = 00 or 01 OSC = OSC enabled during STOP mode. OSC = On when STPMD[1:0] = 00, 01, or 10 MODES NRM = normal PLL crystal clock reference or normal PLL external reference or PLL 1:1 mode. During PLL 1:1 or normal external reference mode, the oscillator is never enabled. Therefore, during these modes, refer to the OSC = On case regardless of STPMD values. EXT = external clock mode REF = PLL reference mode due to losing PLL clock or lock from NRM mode SCM = PLL self-clocked mode due to losing reference clock from NRM mode RESET = immediate reset LOCKS `LK = expecting previous value of LOCKS before entering stop 0->`LK = current value is 0 until lock is regained which then will be the previous value before entering stop 0-> = current value is 0 until lock is regained but lock is never expected to regain LOCS `LC = expecting previous value of LOCS before entering stop 1->`LC = current value is 1 until clock is regained which then will be the previous value before entering stop 1-> = current value is 1 until clock is regained but CLK is never expected to regain 10.8.4.2 Loss-of-Clock Reset When a loss-of-clock condition is recognized, reset is asserted if the LOCRE bit in SYNCR is set. The LOCS bit in SYNSR is cleared after reset. Therefore, the LOC bit must be read in RSR to determine that a loss of clock condition occurred. LOCRE has no effect in external clock mode. To exit reset in PLL mode, the reference must be present, and the PLL must acquire lock. Technical Data 242 MMC2107 - Rev. 2.0 Clock Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Clock Module Functional Description 10.8.5 Clock Operation During Reset In external clock mode, the system is static and does not recognize reset until a clock is applied to EXTAL. Freescale Semiconductor, Inc... In PLL mode, the PLL operates in self-clocked mode (SCM) during reset until the input reference clock to the PLL begins operating within the limits given in the electrical specifications. If a PLL failure causes a reset, the system enters reset using the reference clock. Then the clock source changes to the PLL operating in SCM. If SCM is not functional, the system becomes static. Alternately, if the LOCEN bit in SYNCR is clear when the PLL fails, the system becomes static. If external reset is asserted, the system cannot enter reset unless the PLL is capable of operating in SCM. 10.8.6 PLL Operation In PLL mode, the PLL synthesizes the system clocks. The PLL can multiply the reference clock frequency by 2x to 9x, provided that the system clock (CLKOUT) frequency remains within the range listed in electrical specifications. For example, if the reference frequency is 2 MHz, the PLL can synthesize frequencies of 4 MHz to 18 MHz. In addition, the RFD can reduce the system frequency by dividing the output of the PLL. The RFD is not in the feedback loop of the PLL, so changing the RFD divisor does not affect PLL operation. Figure 10-8 shows the external support circuitry for the crystal oscillator with example component values. Actual component values depend on crystal specifications. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Clock Module For More Information On This Product, Go to: www.freescale.com 243 Freescale Semiconductor, Inc. Clock Module LOCK DETECT LOCK LOSS OF CLOCK DETECT LOCS VDDSYN VSSSYN RSTOUT Freescale Semiconductor, Inc... CHARGE PUMP REFERENCE CLOCK UP PFD FEEDBACK CLOCK CHARGE PUMP DOWN 1:1 PLL MODE VCO CLKOUT FILTER VCO MFD[2:0] OE CLKOUT MFD 2X TO 9X DIVIDE-BYTWO CLKOUT Figure 10-7. PLL Block Diagram C1 C2 VSSSYN EXTAL XTAL ON-CHIP 8-MHz CRYSTAL CONFIGURATION C1 = C2 = 16 pF RF = 1 M RS = 470 VSSSYN RS RF Figure 10-8. Crystal Oscillator Example Technical Data 244 MMC2107 - Rev. 2.0 Clock Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Clock Module Functional Description 10.8.6.1 Phase and Frequency Detector (PFD) Freescale Semiconductor, Inc... The PFD is a dual-latch phase-frequency detector. It compares both the phase and frequency of the reference and feedback clocks. The reference clock comes from either the crystal oscillator or an external clock source. The feedback clock comes from: * CLKOUT in 1:1 PLL mode, or * VCO output divided by two if CLKOUT is disabled in 1:1 PLL mode, or * VCO output divided by the MFD in normal PLL mode When the frequency of the feedback clock equals the frequency of the reference clock, the PLL is frequency-locked. If the falling edge of the feedback clock lags the falling edge of the reference clock, the PFD pulses the UP signal. If the falling edge of the feedback clock leads the falling edge of the reference clock, the PFD pulses the DOWN signal. The width of these pulses relative to the reference clock depends on how much the two clocks lead or lag each other. Once phase lock is achieved, the PFD continues to pulse the UP and DOWN signals for very short durations during each reference clock cycle. These short pulses continually update the PLL and prevent the frequency drift phenomenon known as dead-banding. 10.8.6.2 Charge Pump/Loop Filter In 1:1 PLL mode, the charge pump uses a fixed current. In normal mode the current magnitude of the charge pump varies with the MFD as shown in Table 10-9. Table 10-9. Charge Pump Current and MFD in Normal Mode Operation Charge Pump Current MFD 1X 0 MFD < 2 2X 2 MFD < 6 4X 6 MFD The UP and DOWN signals from the PFD control whether the charge pump applies or removes charge, respectively, from the loop filter. The filter is integrated on the chip. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Clock Module For More Information On This Product, Go to: www.freescale.com 245 Freescale Semiconductor, Inc. Clock Module 10.8.6.3 Voltage Control Output (VCO) The voltage across the loop filter controls the frequency of the VCO output. The frequency-to-voltage relationship (VCO gain) is positive, and the output frequency is four times the target system frequency. Freescale Semiconductor, Inc... 10.8.6.4 Multiplication Factor Divider (MFD) When the PLL is not in 1:1 PLL mode, the MFD divides the output of the VCO and feeds it back to the PFD. The PFD controls the VCO frequency via the charge pump and loop filter such that the reference and feedback clocks have the same frequency and phase. Thus, the frequency of the input to the MFD, which is also the output of the VCO, is the reference frequency multiplied by the same amount that the MFD divides by. For example, if the MFD divides the VCO frequency by six, the PLL is frequency locked when the VCO frequency is six times the reference frequency. The presence of the MFD in the loop allows the PLL to perform frequency multiplication, or synthesis. In 1:1 PLL mode, the MFD is bypassed, and the effective multiplication factor is one. 10.9 Reset The clock module can assert a reset when a loss of clock or loss of lock occurs as described in 10.8 Functional Description. Reset initializes the clock module registers to a known startup state as described in 10.7 Memory Map and Registers. 10.10 Interrupts The clock module does not generate interrupt requests. Technical Data 246 MMC2107 - Rev. 2.0 Clock Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 11. Ports Module Freescale Semiconductor, Inc... 11.1 Contents 11.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248 11.3 Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249 11.4 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 249 11.4.1 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250 11.4.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251 11.4.2.1 Port Output Data Registers . . . . . . . . . . . . . . . . . . . . . . 251 11.4.2.2 Port Data Direction Registers. . . . . . . . . . . . . . . . . . . . . 252 11.4.2.3 Port Pin Data/Set Data Registers . . . . . . . . . . . . . . . . . 253 11.4.2.4 Port Clear Output Data Registers . . . . . . . . . . . . . . . . . 254 11.4.2.5 Port C/D Pin Assignment Register . . . . . . . . . . . . . . . . . 255 11.4.2.6 Port E Pin Assignment Register. . . . . . . . . . . . . . . . . . .256 11.5 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 11.5.1 Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258 11.5.2 Port Digital I/O Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259 11.6 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Ports Module For More Information On This Product, Go to: www.freescale.com 247 Freescale Semiconductor, Inc. Ports Module 11.2 Introduction Many of the pins associated with the external interface may be used for several different functions. Their primary function is to provide an external interface to access off-chip resources. When not used for their primary functions, many of the pins may be used as digital input/output (I/O) pins. In some cases, the pin function is set by the operating mode, and the alternate pin functions are not supported. Freescale Semiconductor, Inc... To facilitate the digital I/O function, these pins are grouped into 8-bit ports. Each port has registers that configure the pins for the desired function, monitor the pins, and control the pins within the ports. R/W / PF7(1) PORT A D[31:24] / PA[7:0] PORT F PORT B D[23:16] / PB[7:0] PORT G A[15:8] / PG[7:0](1) PORT C D[15:8] / PC[7:0] PORT H A[7:0] / PH[7:0](1) PORT D D[7:0] / PD[7:0] PORT I PORT E SHS / RCON / PE7 TA / PE6 TEA / PE5 CSE[1:0] / PE[4:3](1) TC[2:0] / PE[2:0](1) A[22:16] / PF[6:0](1) EB[3:0] / PI[7:4](1) CS[3:0]/ PI[3:0](1) Note 1. These pins are found only on the 144-pin package. Figure 11-1. Ports Module Block Diagram Technical Data 248 MMC2107 - Rev. 2.0 Ports Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Ports Module Signals 11.3 Signals See Table 11-3 in 11.5 Functional Description for signal location and naming convention. 11.4 Memory Map and Registers Freescale Semiconductor, Inc... The ports programming model consists of these registers: * The port output data registers (PORTx) store the data to be driven on the corresponding port pins when the pins are configured for digital output. * The port data direction registers (DDRx) control the direction of the port pin drivers when the pins are configured for digital I/O. * Port pin data/set data registers (PORTxP/SETx): - Reflect the current state of the port pins - Allow for setting individual bits in PORTx * The port clear output data registers (CLRx) allow for clearing individual bits in PORTx. * The port pin assignment registers (PCDPAR and PEPAR) control the function of each pin of the C, D, E, I7, and I6 ports. In emulation mode, accesses to the port registers are ignored and the port access goes external so that emulation hardware can satisfy the port access request. The cycle termination is always provided by the port logic, even in emulation mode. All port registers are word-, half-word, and byte-accessible and are grouped to allow coherent access to port data register groups. Writing to reserved bits in the port registers has no effect and reading returns 0s. The I/O ports have a base address of 0x00c0_0000. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Ports Module For More Information On This Product, Go to: www.freescale.com 249 Freescale Semiconductor, Inc. Ports Module 11.4.1 Memory Map Freescale Semiconductor, Inc... Table 11-1. I/O Port Module Memory Map Address Bits 31-24 Bits 23-16 Bits 15-8 Bits 7-0 Access(1) 0x00c0_0000 PORTA PORTB PORTC PORTD S/U 0x00c0_0004 PORTE PORTF PORTG PORTH S/U 0x00c0_0008 PORTI 0x00c0_000c DDRA DDRB DDRC DDRD S/U 0x00c0_0010 DDRE DDRF DDRG DDRH S/U 0x00c0_0014 DDRI 0x00c0_0018 PORTAP/SETA PORTBP/SETB PORTCP/SETC PORTDP/SETD S/U 0x00c0_001c PORTEP/SETE PORTFP/SETF PORTGP/SETG PORTHP/SETH S/U 0x00c0_0020 PORTIP/SETI 0x00c0_0024 CLRA CLRB CLRC CLRD S/U 0x00c0_0028 CLRE CLRF CLRG CLRH S/U 0x00c0_002c CLRI 0x00c0_0030 PCDPAR 0x00c0_0034- 0x00c0_003c Reserved(2) S/U Reserved(2) S/U Reserved(2) Reserved(2) Reserved (2) PEPAR Reserved(2) S/U S/U S/U S/U 1. S/U = CPU supervisor or user mode access. User mode accesses to supervisor only addresses have no effect and result in a cycle termination transfer error. 2. Writes have no effect, reads return 0s, and the access terminates without a transfer error exception. Technical Data 250 MMC2107 - Rev. 2.0 Ports Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Ports Module Memory Map and Registers 11.4.2 Register Descriptions This subsection provides a description of the I/O port registers. 11.4.2.1 Port Output Data Registers Freescale Semiconductor, Inc... The port output data registers (PORTx) store the data to be driven on the corresponding port x pins when the pins are configured for digital output. Reading PORTx returns the current value in the register, not the port x pin values. The SETx and CLRx registers also affect the PORTx register bits. To set bits in PORTx, write 1s to the corresponding bits in PORTxP/SETx. To clear bits in PORTx, write 0s to the corresponding bits in CLRx. PORTx are read/write registers when not in emulation mode. Reset sets PORTx. Address: 0x00c0_0000 -- PORTA 0x00c0_0001 -- PORTB 0x00c0_0002 -- PORTC 0x00c0_0003 -- PORTD 0x00c0_0004 -- PORTE 0x00c0_0005 -- PORTF 0x00c0_0006 -- PORTG 0x00c0_0007 -- PORTH 0x00c0_0008 -- PORTI 7 6 5 4 3 2 1 Bit 0 PORTx7 PORTx6 PORTx5 PORTx4 PORTx3 PORTx2 PORTx1 PORTx0 1 1 1 1 1 1 1 1 Read: Write: Reset: Figure 11-2. Port Output Data Registers (PORTx) MMC2107 - Rev. 2.0 MOTOROLA Technical Data Ports Module For More Information On This Product, Go to: www.freescale.com 251 Freescale Semiconductor, Inc. Ports Module 11.4.2.2 Port Data Direction Registers A port data direction register (DDRx) controls the direction of the port x pin drivers when the pins are configured for digital I/O. Setting any bit in DDRx configures the corresponding port x pin as an output. Clearing any bit in DDRx configures the corresponding pin as an input. When a pin is not configured for digital I/O, its corresponding data direction bit has no effect. Freescale Semiconductor, Inc... DDRx are read/write registers when not in emulation mode. Reset clears DDRx. Address: 0x00c0_000c -- DDRA 0x00c0_000d -- DDRB 0x00c0_000e -- DDRC 0x00c0_000f -- DDRD 0x00c0_0010 -- DDRE 0x00c0_0011 -- DDRF 0x00c0_0012 -- DDRG 0x00c0_0013 -- DDRH 0x00c0_0014 -- DDRI Bit 7 6 5 4 3 2 1 Bit 0 DDRx7 DDRx6 DDRx5 DDRx4 DDRx3 DDRx2 DDRx1 DDRx0 0 0 0 0 0 0 0 0 Read: Write: Reset: Figure 11-3. Port Data Direction Registers (DDRx) DDRx[7:0] -- Port x Data Direction Bits 1 = Pin configured as output 0 = Pin configured as input Technical Data 252 MMC2107 - Rev. 2.0 Ports Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Ports Module Memory Map and Registers 11.4.2.3 Port Pin Data/Set Data Registers Reading a port pin data/set data register (PORTxP/SETx) returns the current state of the port x pins. Writing 1s to PORTxP/SETx sets the corresponding bits in PORTx. Writing 0s has no effect. PORTxP/SETx are read/write registers when not in emulation mode. Freescale Semiconductor, Inc... Address: 0x00c0_0018 -- PORTAP/SETA 0x00c0_0019 -- PORTBP/SETB 0x00c0_001a -- PORTCP/SETC 0x00c0_001b -- PORTDP/SETD 0x00c0_001c -- PORTEP/SETE 0x00c0_001d -- PORTFP/SETF 0x00c0_001e -- PORTGP/SETG 0x00c0_001f -- PORTHP/SETH 0x00c0_0020 -- PORTIP/SETI Bit 7 6 5 4 3 2 1 Bit 0 Read: PORTxP7 PORTxP6 PORTxP5 PORTxP4 PORTxP3 PORTxP2 PORTxP1 PORTxP0 Write: SETx7 SETx6 SETx5 SETx4 SETx3 SETx2 SETx1 SETx0 Reset: P P P P P P P P P = Current pin state Figure 11-4. Port Pin Data/Set Data Registers (PORTxP/SETx) MMC2107 - Rev. 2.0 MOTOROLA Technical Data Ports Module For More Information On This Product, Go to: www.freescale.com 253 Freescale Semiconductor, Inc. Ports Module 11.4.2.4 Port Clear Output Data Registers Writing 0s to a port clear output data register (CLRx) clears the corresponding bits in PORTx. Writing 1s has no effect. Reading CLRx returns 0s. CLRx are read/write registers when not in emulation mode. Freescale Semiconductor, Inc... Address: 0x00c0_0024 -- CLRA 0x00c0_0025 -- CLRB 0x00c0_0026 -- CLRC 0x00c0_0027 -- CLRD 0x00c0_0028 -- CLRE 0x00c0_0029 -- CLRF 0x00c0_002a -- CLRG 0x00c0_002b -- CLRH 0x00c0_002c -- CLRI Bit 7 6 5 4 3 2 1 Bit 0 Read: 0 0 0 0 0 0 0 0 Write: CLRx7 CLRx6 CLRx5 CLRx4 CLRx3 CLRx2 CLRx1 CLRx0 Reset: 0 0 0 0 0 0 0 0 Figure 11-5. Port Clear Output Data Registers (CLRx) Technical Data 254 MMC2107 - Rev. 2.0 Ports Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Ports Module Memory Map and Registers 11.4.2.5 Port C/D Pin Assignment Register The port C/D pin assignment register (PCDPAR) controls the pin function of ports C, D, I7, and I6. PCDPAR is a read/write register when not in emulation mode. Address: 0x00c0_0030 Bit 7 Read: 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Freescale Semiconductor, Inc... PCDPA Write: Reset: See note = Writes have no effect and the access terminates without a transfer error exception. Note: Reset state determined during reset configuration. PCDPA = 1 except in single-chip mode or when an external boot device is selected with a 16-bit port size in master mode. Figure 11-6. Port C, D, I7, and I6 Pin Assignment Register (PCDPAR) PCDPA -- Port C, D, I7, and I6 Pin Assignment Bit 1 = Port C, D, I7, and I6 pins configured for primary function 0 = Port C, D, I7, and I6 pins configured for digital I/O MMC2107 - Rev. 2.0 MOTOROLA Technical Data Ports Module For More Information On This Product, Go to: www.freescale.com 255 Freescale Semiconductor, Inc. Ports Module 11.4.2.6 Port E Pin Assignment Register The port E pin assignment register (PEPAR) controls the pin function of port E. PEPAR is a read/write register when not in emulation mode. Address: 0x00c0_0031 Bit 7 6 5 4 3 2 1 Bit 0 PEPA7 PEPA6 PEPA5 PEPA4 PEPA3 PEPA2 PEPA1 PEPA0 Freescale Semiconductor, Inc... Read: Write: Reset: See note Note: Reset state determined during reset configuration as shown in Table 11-2. Figure 11-7. Port E Pin Assignment Register (PEPAR) PEPA[7:0] -- Port E Pin Assignment Bits 1 = Port E pins configured for primary function 0 = Port E pins configured for digital I/O Table 11-2. PEPAR Reset Values PEPAR Pin Master Mode Single-Chip Mode Emulation Mode PEPA7 SHS 1 0 1 PEPA6 TA 1 0 1 PEPA5 TEA 1 0 1 PEPA[4:3] CSE[1:0] 0 0 1 PEPA[2:0] TC[2:0] 0 0 1 Technical Data 256 MMC2107 - Rev. 2.0 Ports Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Ports Module Functional Description 11.5 Functional Description The initial pin function is determined during reset configuration. The pin assignment registers (PCDPAR and PEPAR) allow the user to select between digital I/O or another pin function after reset. In single-chip mode, all pins are configured as digital I/O by default. Every digital I/O pin is individually configurable as an input or an output via a data direction register (DDRx). Freescale Semiconductor, Inc... Every port has an output data register (PORTx) and a pin data register (PORTxP/SETx) to monitor and control the state of its pins. Data written to PORTx is stored and then driven to the corresponding PORTx pins configured as outputs. Reading PORTx returns the current state of the register regardless of the state of the corresponding pins. Reading PORTxP returns the current state of the corresponding pins, regardless of whether the pins are input or output. Every port has a set register (PORTxP/SETx) and a clear register (CLRx) for setting or clearing individual bits in PORTx. In master mode and emulation mode, ports A and B function as the upper external data bus, D[31:16]. When the PCDPA bit is set, ports C and D function as the lower external data bus, D[15:0]. Ports E-I are configured to support external memory and emulation functions. In master mode, the function of EB[3:2] is determined by the PCDPA bit. The function of CS[3:0] is determined by the individual chip select enable (CSENx) bits. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Ports Module For More Information On This Product, Go to: www.freescale.com 257 Freescale Semiconductor, Inc. Ports Module 11.5.1 Pin Functions Freescale Semiconductor, Inc... Pin Port Table 11-3. Ports A-I Supported Pin Functions Master Mode Single-Chip Mode Emulation Mode(1) D[31:24] A D[31:24] (I/O) PA[7:0] (I/O) D[31:24] (I/O) D[23:16] B D[23:16] (I/O) PB[7:0](I/O) D[23:16](I/O) D[15:8] D[15:8] (I/O) (PCDPA = 1) C or PC[7:0] (I/O) (PCDPA = 0) PC[7:0] (I/O) (PCDPA = 0)(2) D[15:8] (I/O) (PCDPA = 1) D[7:0] D[7:0] (I/O) (PCDPA = 1) D or PD[7:0] (I/O) (PCDPA = 0) PD[7:0] (I/O) (PCDPA = 0)(2) D[7:0] (I/O) (PCDPA = 1) SHS(3) SHS (O) (PEPAR7 = 1) or PE7 (I/O) (PEPAR7 = 0) PE7 (I/O) (PEPAR7 = 0)(4) SHS (O) (PEPAR7 = 1) TA TA (I) (PEPAR6 = 1) or PE6 (I/O) (PEPAR6 = 0) PE6 (I/O) (PEPAR6 = 0)(4) TA (I) (PEPAR6 = 1) TEA (I) (PEPAR5 = 1) E or PE5 (I/O) (PEPAR5 = 0) PE5 (I/O) (PEPAR5 = 0)(4) TEA (I) (PEPAR5 = 1) TEA CSE[1:0] (O) (PEPAR[4:3] = 1) or PE[4:3] (I/O) (PEPAR[4:3] = 0)(4) CSE[1:0] (O) (PEPAR[4:3] = 1) PE[4:3] (I/O) (PEPAR[4:3] = 0) CSE[1:0] TC[2:0] (O) (PEPAR[2:0] = 1) or PE[2:0] (I/O) (PEPAR[2:0] = 0)(4) TC[2:0] (O) (PEPAR[2:0] = 1) PE[2:0] (I/O) (PEPAR[2:0] = 0) TC[2:0] R/W A[22:16] F R/W (O) PF7 (I/O) R/W (O) A[22:16] (O) PF[6:0] (I/O) A[22:16] (O) A[15:8] G A[15:8] (O) PG[7:0] (I/O) A[15:8] (O) A[7:0] H A[7:0] (O) PH[7:0] (I/O) A[7:0] (O) EB[3:2] (O) (PCDPA = 1) or PI[7:6] (I/O) (PCDPA = 0) PI[7:6] (I/O) (PCDPA = 0)(2) EB[3:2] (O) (PCDPA = 1) EB[1:0] (O) PI[5:4] (I/O) EB[1:0] (O) CS[3:0] (O) (CSENx = 1) or PI[3:0] (I/O) (CSENx = 0) PI[3:0] (I/O)(5) CS[3:0] (O)(5) EB[3:2] EB[1:0] I CS[3:0] 1. Digital I/O pin function provided by port replacement unit. 2. Writing PCDPA = 1 has an undefined pin operation for D[31:16] and EB[3:2] in single-chip mode. 3. This pin functions as the reset configuration override enable (RCON) during reset. 4. Writing PEPAx = 1 has an undefined pin operation for port E pins in single-chip mode. 5. CSENx has no effect on selecting CS[3:0] pin function in single-chip or emulation modes. Technical Data 258 MMC2107 - Rev. 2.0 Ports Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Ports Module Interrupts 11.5.2 Port Digital I/O Timing Input data on all pins configured as digital I/O is synchronized to the rising edge of CLKOUT. See Figure 11-8. CLKOUT Freescale Semiconductor, Inc... INPUT PIN REGISTER PIN DATA Figure 11-8. Digital Input Timing Data written to PORTx of any pin configured as a digital output is immediately driven to its respective pin. See Figure 11-9. CLKOUT OUTPUT DATA REGISTER OUTPUT PIN Figure 11-9. Digital Output Timing 11.6 Interrupts The ports module does not generate interrupt requests. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Ports Module For More Information On This Product, Go to: www.freescale.com 259 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Ports Module Technical Data 260 MMC2107 - Rev. 2.0 Ports Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 12. Edge Port Module (EPORT) 12.1 Contents Freescale Semiconductor, Inc... 12.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261 12.3 Low-Power Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 262 12.3.1 Wait and Doze Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262 12.3.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .263 12.4 Interrupt/General-Purpose I/O Pin Descriptions . . . . . . . . . . . 263 12.5 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 263 12.5.1 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263 12.5.2 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264 12.5.2.1 EPORT Pin Assignment Register . . . . . . . . . . . . . . . . . 264 12.5.2.2 EPORT Data Direction Register. . . . . . . . . . . . . . . . . . .266 12.5.2.3 Edge Port Interrupt Enable Register . . . . . . . . . . . . . . . 267 12.5.2.4 Edge Port Data Register . . . . . . . . . . . . . . . . . . . . . . . . 268 12.5.2.5 Edge Port Pin Data Register . . . . . . . . . . . . . . . . . . . . . 268 12.5.2.6 Edge Port Flag Register. . . . . . . . . . . . . . . . . . . . . . . . . 269 12.2 Introduction The edge port module (EPORT) has eight external interrupt pins. Each pin can be configured individually as a low level-sensitive interrupt pin, an edge-detecting interrupt pin (rising edge, falling edge, or both), or a general-purpose input/output (I/O) pin. See Figure 12-1. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Edge Port Module (EPORT) For More Information On This Product, Go to: www.freescale.com 261 Freescale Semiconductor, Inc. Edge Port Module (EPORT) STOP MODE EPPAR[2n, 2n + 1] EDGE DETECT LOGIC D0 EPFR[n] D0 Q D1 Q IPBUS Freescale Semiconductor, Inc... D1 TO INTERRUPT CONTROLLER EPPDR[n] SYNCHRONIZER RISING EDGE OF CLOCK EPIER[n] INTx PIN EPDR[n] EPDDR[n] Figure 12-1. EPORT Block Diagram 12.3 Low-Power Mode Operation This subsection describes the operation of the EPORT module in low-power modes. 12.3.1 Wait and Doze Modes In wait and doze modes, the EPORT module continues to operate normally and may be configured to exit the low-power modes by generating an interrupt request on either a selected edge or a low level on an external pin. Technical Data 262 MMC2107 - Rev. 2.0 Edge Port Module (EPORT) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Edge Port Module (EPORT) Interrupt/General-Purpose I/O Pin Descriptions 12.3.2 Stop Mode In stop mode, there are no clocks available to perform the edge-detect function. Only the level-detect logic is active (if configured) to allow any low level on the external interrupt pin to generate an interrupt (if enabled) to exit stop mode. Freescale Semiconductor, Inc... NOTE: The input pin synchronizer is bypassed for the level-detect logic since no clocks are available. 12.4 Interrupt/General-Purpose I/O Pin Descriptions All pins default to general-purpose input pins at reset. The pin value is synchronized to the rising edge of CLKOUT when read from the EPORT pin data register (EPPDR). The values used in the edge/level detect logic are also synchronized to the rising edge of CLKOUT. These pins use Schmitt triggered input buffers which have built in hysteresis designed to decrease the probability of generating false edge-triggered interrupts for slow rising and falling input signals. 12.5 Memory Map and Registers This subsection describes the memory map and register structure. 12.5.1 Memory Map Refer to Table 12-1 for a description of the EPORT memory map. The EPORT has a base address of 0x00c6_0000. Table 12-1. Edge Port Module Memory Map Address Bits 15-8 0x00c6_0000 Bits 7-0 EPORT pin assignment register (EPPAR) Access(1) S 0x00c6_0002 EPORT data direction register (EPDDR) EPORT interrupt enable register (EPIER) S 0x00c6_0004 EPORT data register (EPDR) EPORT pin data register (EPPDR) S/U 0x00c6_0006 EPORT flag register (EPFR) Reserved(2) S/U 1. S = CPU supervisor mode access only. S/U = CPU supervisor or user mode access. User mode accesses to supervisor only addresses have no effect and result in a cycle termination transfer error. 2. Writing to reserved address locations has no effect, and reading returns 0s. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Edge Port Module (EPORT) For More Information On This Product, Go to: www.freescale.com 263 Freescale Semiconductor, Inc. Edge Port Module (EPORT) 12.5.2 Registers Freescale Semiconductor, Inc... The EPORT programming model consists of these registers: * The EPORT pin assignment register (EPPAR) controls the function of each pin individually. * The EPORT data direction register (EPDDR) controls the direction of each one of the pins individually. * The EPORT interrupt enable register (EPIER) enables interrupt requests for each pin individually. * The EPORT data register (EPDR) holds the data to be driven to the pins. * The EPORT pin data register (EPPDR) reflects the current state of the pins. * The EPORT flag register (EPFR) individually latches EPORT edge events. 12.5.2.1 EPORT Pin Assignment Register Address: 0x00c6_0000 and 0x00c6_0001 Bit 15 14 13 12 11 10 9 Bit 8 Read: EPPA7 EPPA6 EPPA5 EPPA4 Write: Reset: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Read: EPPA3 EPPA2 EPPA1 EPPA0 Write: Reset: 0 0 0 0 0 0 0 0 Figure 12-2. EPORT Pin Assignment Register (EPPAR) Technical Data 264 MMC2107 - Rev. 2.0 Edge Port Module (EPORT) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Edge Port Module (EPORT) Memory Map and Registers EPPA[7:0] -- EPORT Pin Assignment Select Fields The read/write EPPAx fields configure EPORT pins for level detection and rising and/or falling edge detection as Table 12-2 shows. Pins configured as level-sensitive are inverted so that a logic 0 on the external pin represents a valid interrupt request. Level-sensitive interrupt inputs are not latched. To guarantee that a level-sensitive interrupt request is acknowledged, the interrupt source must keep the signal asserted until acknowledged by software. Freescale Semiconductor, Inc... Pins configured as edge-triggered are latched and need not remain asserted for interrupt generation. A pin configured for edge detection is monitored regardless of its configuration as input or output. Table 12-2. EPPAx Field Settings EPPAx Pin Configuration 00 Pin INTx level-sensitive 01 Pin INTx rising edge triggered 10 Pin INTx falling edge triggered 11 Pin INTx both falling edge and rising edge triggered Interrupt requests generated in the EPORT module can be masked by the interrupt controller module. EPPAR functionality is independent of the selected pin direction. Reset clears the EPPAx fields. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Edge Port Module (EPORT) For More Information On This Product, Go to: www.freescale.com 265 Freescale Semiconductor, Inc. Edge Port Module (EPORT) 12.5.2.2 EPORT Data Direction Register Address: 0x00c6_0002 Bit 7 6 5 4 3 2 1 Bit 0 EPDD7 EPDD6 EPDD5 EPDD4 EPDD3 EPDD2 EPDD1 EPDD0 0 0 0 0 0 0 0 0 Read: Write: Reset: Freescale Semiconductor, Inc... Figure 12-3. EPORT Data Direction Register (EPDDR) EPDD[7:0] -- Edge Port Data Direction Bits Setting any bit in the EPDDR configures the corresponding pin as an output. Clearing any bit in EPDDR configures the corresponding pin as an input. Pin direction is independent of the level/edge detection configuration. Reset clears EPDD[7:0]. To use an EPORT pin as an external interrupt request source, its corresponding bit in EPDDR must be clear. Software can generate interrupt requests by programming the EPORT data register when the EPDDR selects output. 1 = Corresponding EPORT pin configured as output 0 = Corresponding EPORT pin configured as input Technical Data 266 MMC2107 - Rev. 2.0 Edge Port Module (EPORT) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Edge Port Module (EPORT) Memory Map and Registers 12.5.2.3 Edge Port Interrupt Enable Register Address: 0x00c6_0003 Bit 7 6 5 4 3 2 1 Bit 0 EPIE7 EPIE6 EPIE5 EPIE4 EPIE3 EPIE2 EPIE1 EPIE0 0 0 0 0 0 0 0 0 Read: Write: Reset: Freescale Semiconductor, Inc... Figure 12-4. EPORT Port Interrupt Enable Register (EPIER) EPIE[7:0] -- Edge Port Interrupt Enable Bits The read/write EPIE[7:0] bits enable EPORT interrupt requests. If a bit in EPIER is set, EPORT generates an interrupt request when: * The corresponding bit in the EPORT flag register (EPFR) is set or later becomes set, or * The corresponding pin level is low and the pin is configured for level-sensitive operation Clearing a bit in EPIER negates any interrupt request from the corresponding EPORT pin. Reset clears EPIE[7:0]. 1 = Interrupt requests from corresponding EPORT pin enabled 0 = Interrupt requests from corresponding EPORT pin disabled MMC2107 - Rev. 2.0 MOTOROLA Technical Data Edge Port Module (EPORT) For More Information On This Product, Go to: www.freescale.com 267 Freescale Semiconductor, Inc. Edge Port Module (EPORT) 12.5.2.4 Edge Port Data Register Address: 0x00c6_0004 Bit 7 6 5 4 3 2 1 Bit 0 EPD7 EPD6 EPD5 EPD4 EPD3 EPD2 EPD1 EPD0 1 1 1 1 1 1 1 1 Read: Write: Freescale Semiconductor, Inc... Reset: Figure 12-5. EPORT Port Data Register (EPDR) EPD[7:0] -- Edge Port Data Bits Data written to EPDR is stored in an internal register; if any pin of the port is configured as an output, the bit stored for that pin is driven onto the pin. Reading EDPR returns the data stored in the register. Reset sets EPD[7:0]. 12.5.2.5 Edge Port Pin Data Register Address: 0x00c6_0005 Read: Bit 7 6 5 4 3 2 1 Bit 0 EPPD7 EPPD6 EPPD5 EPPD4 EPPD3 EPPD2 EPPD1 EPPD0 P P P P P P P P Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. P = Current pin state Figure 12-6. EPORT Port Pin Data Register (EPPDR) EPPD[7:0] -- Edge Port Pin Data Bits The read-only EPPDR reflects the current state of the EPORT pins. Writing to EPPDR has no effect, and the write cycle terminates normally. Reset does not affect EPPDR. Technical Data 268 MMC2107 - Rev. 2.0 Edge Port Module (EPORT) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Edge Port Module (EPORT) Memory Map and Registers 12.5.2.6 Edge Port Flag Register Address: 0x00c6_0006 Bit 7 6 5 4 3 2 1 Bit 0 EPF7 EPF6 EPF5 EPF4 EPF3 EPF2 EPF1 EPF0 0 0 0 0 0 0 0 0 Read: Write: Reset: Freescale Semiconductor, Inc... Figure 12-7. EPORT Port Flag Register (EPFR) EPF[7:0] -- Edge Port Flag Bits When an EPORT pin is configured for edge triggering, its corresponding read/write bit in EPFR indicates that the selected edge has been detected. Reset clears EPF[7:0]. 1 = Selected edge for INTx pin has been detected. 0 = Selected edge for INTx pin has not been detected. Bits in this register are set when the selected edge is detected on the corresponding pin. A bit remains set until cleared by writing a 1 to it. Writing 0 has no effect. If a pin is configured as level-sensitive (EPPARx = 00), pin transitions do not affect this register. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Edge Port Module (EPORT) For More Information On This Product, Go to: www.freescale.com 269 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Edge Port Module (EPORT) Technical Data 270 MMC2107 - Rev. 2.0 Edge Port Module (EPORT) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 13. Watchdog Timer Module 13.1 Contents Freescale Semiconductor, Inc... 13.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271 13.3 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .272 13.3.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .272 13.3.2 Doze Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .272 13.3.3 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .272 13.3.4 Debug Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272 13.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273 13.5 Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273 13.6 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 274 13.6.1 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274 13.6.2 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274 13.6.2.1 Watchdog Control Register . . . . . . . . . . . . . . . . . . . . . . 275 13.6.2.2 Watchdog Modulus Register . . . . . . . . . . . . . . . . . . . . . 277 13.6.2.3 Watchdog Count Register . . . . . . . . . . . . . . . . . . . . . . .278 13.6.2.4 Watchdog Service Register . . . . . . . . . . . . . . . . . . . . . . 279 13.2 Introduction The watchdog timer is a 16-bit timer used to help software recover from runaway code. The watchdog timer has a free-running down-counter (watchdog counter) that generates a reset on underflow. To prevent a reset, software must periodically restart the countdown. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Watchdog Timer Module For More Information On This Product, Go to: www.freescale.com 271 Freescale Semiconductor, Inc. Watchdog Timer Module 13.3 Modes of Operation This subsection describes the operation of the watchdog timer in low-power modes and debug mode of operation. Freescale Semiconductor, Inc... 13.3.1 Wait Mode In wait mode with the WAIT bit set in the watchdog control register (WCR), watchdog timer operation stops. In wait mode with the WAIT bit clear, the watchdog timer continues to operate normally. 13.3.2 Doze Mode In doze mode with the DOZE bit set in WCR, watchdog timer module operation stops. In doze mode with the DOZE bit clear, the watchdog timer continues to operate normally. 13.3.3 Stop Mode The watchdog operation stops in stop mode. When stop mode is exited, the watchdog operation continues operation from the state it was in prior to entering stop mode. 13.3.4 Debug Mode In debug mode with the DBG bit set in WCR, watchdog timer module operation stops. In debug mode with the DBG bit clear, the watchdog timer continues to operate normally. When debug mode is exited, watchdog timer operation continues from the state it was in before entering debug mode, but any updates made in debug mode remain. Technical Data 272 MMC2107 - Rev. 2.0 Watchdog Timer Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Watchdog Timer Module Block Diagram 13.4 Block Diagram IPBUS 16-BIT WCNTR Freescale Semiconductor, Inc... SYSTEM CLOCK DIVIDE BY 4096 16-BIT WSR 16-BIT WATCHDOG COUNTER EN COUNT = 0 RESET LOAD COUNTER WAIT DOZE 16-BIT WMR DBG IPBUS Figure 13-1. Watchdog Timer Block Diagram 13.5 Signals The watchdog timer module has no off-chip signals. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Watchdog Timer Module For More Information On This Product, Go to: www.freescale.com 273 Freescale Semiconductor, Inc. Watchdog Timer Module 13.6 Memory Map and Registers This subsection describes the memory map and registers for the watchdog timer. The watchdog timer has a base address of 0x00c7_0000. 13.6.1 Memory Map Freescale Semiconductor, Inc... Refer to Table 13-1 for an overview of the watchdog memory map. Table 13-1. Watchdog Timer Module Memory Map Address Bits 15-8 Bits 7-0 Access(1) 0x00c7_0000 Watchdog control register (WCR) S 0x00c7_0002 Watchdog modulus register (WMR) S 0x00c7_0004 Watchdog count register (WCNTR) S/U 0x00c7_0006 Watchdog service register (WSR) S/U 1. S = CPU supervisor mode access only. S/U = CPU supervisor or user mode access. User mode accesses to supervisor only addresses have no effect and result in a cycle termination transfer error. 13.6.2 Registers The watchdog timer programming model consists of these registers: * The watchdog control register (WCR) configures watchdog timer operation. * The watchdog modulus register (WMR) determines the timer modulus reload value. * The watchdog count register (WCNTR) provides visibility to the watchdog counter value. * The watchdog service register (WSR) requires a service sequence to prevent reset. Technical Data 274 MMC2107 - Rev. 2.0 Watchdog Timer Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Watchdog Timer Module Memory Map and Registers 13.6.2.1 Watchdog Control Register The 16-bit read/write watchdog control register (WCR) configures watchdog timer operation. Address: 0x00c7_0000 and 0x00c7_0001 Read: Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 WAIT DOZE DBG EN 1 1 1 1 Freescale Semiconductor, Inc... Write: Reset: Read: Write: Reset: 0 0 0 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 13-2. Watchdog Control Register (WCR) WAIT -- Wait Mode Bit The read-always, write-once WAIT bit controls the function of the watchdog timer in wait mode. Once written, the WAIT bit is not affected by further writes except in debug mode. Reset sets WAIT. 1 = Watchdog timer stopped in wait mode 0 = Watchdog timer not affected in wait mode DOZE -- Doze Mode Bit The read-always, write-once DOZE bit controls the function of the watchdog timer in doze mode. Once written, the DOZE bit is not affected by further writes except in debug mode. Reset sets DOZE. 1 = Watchdog timer stopped in doze mode 0 = Watchdog timer not affected in doze mode MMC2107 - Rev. 2.0 MOTOROLA Technical Data Watchdog Timer Module For More Information On This Product, Go to: www.freescale.com 275 Freescale Semiconductor, Inc. Watchdog Timer Module DBG -- Debug Mode Bit The read-always, write-once DBG bit controls the function of the watchdog timer in debug mode. Once written, the DBG bit is not affected by further writes except in debug mode. Freescale Semiconductor, Inc... During debug mode, watchdog timer registers can be written and read normally. When debug mode is exited, timer operation continues from the state it was in before entering debug mode, but any updates made in debug mode remain. If a write-once register is written for the first time in debug mode, the register is still writable when debug mode is exited. 1 = Watchdog timer stopped in debug mode 0 = Watchdog timer not affected in debug mode NOTE: Changing the DBG bit from 1 to 0 during debug mode starts the watchdog timer. Changing the DBG bit from 0 to 1 during debug mode stops the watchdog timer. EN -- Watchdog Enable Bit The read-always, write-once EN bit enables the watchdog timer. Once written, the EN bit is not affected by further writes except in debug mode. When the watchdog timer is disabled, the watchdog counter and prescaler counter are held in a stopped state. 1 = Watchdog timer enabled 0 = Watchdog timer disabled Technical Data 276 MMC2107 - Rev. 2.0 Watchdog Timer Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Watchdog Timer Module Memory Map and Registers 13.6.2.2 Watchdog Modulus Register Address: 0x00c7_0002 and 0x00c7_0003 Bit 15 14 13 12 11 10 9 Bit 8 WM15 WM14 WM13 WM12 WM11 WM10 WM9 WM8 1 1 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 WM7 WM6 WM5 WM4 WM3 WM2 WM1 WM0 1 1 1 1 1 1 1 1 Read: Write: Freescale Semiconductor, Inc... Reset: Read: Write: Reset: Figure 13-3. Watchdog Modulus Register (WMR) WM[15:0] -- Watchdog Modulus Field The read-always, write-once WM[15:0] field contains the modulus that is reloaded into the watchdog counter by a service sequence. Once written, the WM[15:0] field is not affected by further writes except in debug mode. Writing to WMR immediately loads the new modulus value into the watchdog counter. The new value is also used at the next and all subsequent reloads. Reading WMR returns the value in the modulus register. Reset initializes the WM[15:0] field to 0xFFFF. NOTE: The prescaler counter is reset anytime a new value is loaded into the watchdog counter and also during reset. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Watchdog Timer Module For More Information On This Product, Go to: www.freescale.com 277 Freescale Semiconductor, Inc. Watchdog Timer Module 13.6.2.3 Watchdog Count Register Address: 0x00c7_0004 and 0x00c7_0005 Read: Bit 15 14 13 12 11 10 9 Bit 8 WC15 WC14 WC13 WC12 WC11 WC10 WC9 WC8 1 1 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 WC7 WC6 WC5 WC4 WC3 WC2 WC1 WC0 1 1 1 1 1 1 1 1 Write: Freescale Semiconductor, Inc... Reset: Read: Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 13-4. Watchdog Count Register (WCNTR) WC[15:0] -- Watchdog Count Field The read-only WC[15:0] field reflects the current value in the watchdog counter. Reading the 16-bit WCNTR with two 8-bit reads is not guaranteed to return a coherent value. Writing to WCNTR has no effect, and write cycles are terminated normally. Technical Data 278 MMC2107 - Rev. 2.0 Watchdog Timer Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Watchdog Timer Module Memory Map and Registers 13.6.2.4 Watchdog Service Register When the watchdog timer is enabled, writing 0x5555 and then 0xAAAA to the watchdog service register (WSR) before the watchdog counter times out prevents a reset. If WSR is not serviced before the timeout, the watchdog timer sends a signal to the reset controller module which sets the WDR bit and asserts a system reset. Freescale Semiconductor, Inc... Both writes must occur in the order listed before the timeout, but any number of instructions can be executed between the two writes. However, writing any value other than 0x5555 or 0xAAAA to WSR resets the servicing sequence, requiring both values to be written to keep the watchdog timer from causing a reset. Address: 0x00c7_0006 and 0x00c7_0007 Bit 15 14 13 12 11 10 9 Bit 8 WS15 WS14 WS13 WS12 WS11 WS10 WS9 WS8 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 WS7 WS6 WS5 WS4 WS3 WS2 WS1 WS0 0 0 0 0 0 0 0 0 Read: Write: Reset: Read: Write: Reset: Figure 13-5. Watchdog Service Register (WSR) MMC2107 - Rev. 2.0 MOTOROLA Technical Data Watchdog Timer Module For More Information On This Product, Go to: www.freescale.com 279 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Watchdog Timer Module Technical Data 280 MMC2107 - Rev. 2.0 Watchdog Timer Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 14. Programmable Interrupt Timer Modules (PIT1 and PIT2) Freescale Semiconductor, Inc... 14.1 Contents 14.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282 14.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282 14.4 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .283 14.4.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .283 14.4.2 Doze Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .283 14.4.3 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .283 14.4.4 Debug Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283 14.5 Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283 14.6 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 284 14.6.1 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284 14.6.2 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284 14.6.2.1 PIT Control and Status Register . . . . . . . . . . . . . . . . . .285 14.6.2.2 PIT Modulus Register . . . . . . . . . . . . . . . . . . . . . . . . . . 288 14.6.2.3 PIT Count Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289 14.7 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290 14.7.1 Set-and-Forget Timer Operation . . . . . . . . . . . . . . . . . . . . 290 14.7.2 Free-Running Timer Operation . . . . . . . . . . . . . . . . . . . . . 291 14.7.3 Timeout Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .291 14.8 Interrupt Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Programmable Interrupt Timer Modules (PIT1 and PIT2) For More Information On This Product, Go to: www.freescale.com 281 Freescale Semiconductor, Inc. Programmable Interrupt Timer Modules (PIT1 and PIT2) 14.2 Introduction The programmable interrupt timer (PIT) is a 16-bit timer that provides precise interrupts at regular intervals with minimal processor intervention. The timer can either count down from the value written in the modulus latch, or it can be a free-running down-counter. Freescale Semiconductor, Inc... This device has two programmable interrupt timers. PIT1 has a base address located at 0x00c8_0000. PIT2 base address is 0x00c9_0000. 14.3 Block Diagram IPBUS 16-BIT PCNTR SYSTEM CLOCK PRESCALER COUNT = 0 16-BIT PIT COUNTER PIF LOAD COUNTER EN PRE[3:0] TO INTERRUPT CONTROLLER PIE OVW RLD PDOZE PDBG 16-BIT PMR IPBUS Figure 14-1. PIT Block Diagram Technical Data 282 MMC2107 - Rev. 2.0 Programmable Interrupt Timer Modules (PIT1 and PIT2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Programmable Interrupt Timer Modules (PIT1 and PIT2) Modes of Operation 14.4 Modes of Operation This subsection describes the three low-power modes and the debug mode. Freescale Semiconductor, Inc... 14.4.1 Wait Mode In wait mode, the PIT module continues to operate normally and can be configured to exit the low-power mode by generating an interrupt request. 14.4.2 Doze Mode In doze mode with the PDOZE bit set in the PIT control and status register (PCSR), PIT module operation stops. In doze mode with the PDOZE bit clear, doze mode does not affect PIT operation. When doze mode is exited, PIT operation continues from the state it was in before entering doze mode. 14.4.3 Stop Mode In stop mode, the system clock is absent, and PIT module operation stops. 14.4.4 Debug Mode In debug mode with the PDBG bit set in PCSR, PIT module operation stops. In debug mode with the PDBG bit clear, debug mode does not affect PIT operation. When debug mode is exited, PIT operation continues from the state it was in before entering debug mode, but any updates made in debug mode remain. 14.5 Signals The PIT module has no off-chip signals. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Programmable Interrupt Timer Modules (PIT1 and PIT2) For More Information On This Product, Go to: www.freescale.com 283 Freescale Semiconductor, Inc. Programmable Interrupt Timer Modules (PIT1 and PIT2) 14.6 Memory Map and Registers This subsection describes the memory map and register structure for PIT1 and PIT2. 14.6.1 Memory Map Freescale Semiconductor, Inc... Refer to Table 14-1 for a description of the memory map. This device has two programmable interrupt timers. PIT1 has a base address located at 0x00c8_0000. PIT2 base address is 0x00c9_0000. Table 14-1. Programmable Interrupt Timer Modules Memory Map PIT1 Address PIT2 Address 0x00c8_0000 0x00c9_0000 PIT control and status register (PCSR) S 0x00c8_0002 0x00c9_0002 PIT modulus register (PMR) S 0x00c8_0004 0x00c9_0004 PIT count register (PCNTR) S/U 0x00c8_0006 0x00c9_0006 Unimplemented(2) -- Bits 15-8 Bits 7-0 Access(1) 1. S = CPU supervisor mode access only. S/U = CPU supervisor or user mode access. User mode accesses to supervisor only addresses have no effect and result in a cycle termination transfer error. 2. Accesses to unimplemented address locations have no effect and result in a cycle termination transfer error. 14.6.2 Registers The PIT programming model consists of these registers: * The PIT control and status register (PCSR) configures the timer's operation. * The PIT modulus register (PMR) determines the timer modulus reload value. * The PIT count register (PCNTR) provides visibility to the counter value. Technical Data 284 MMC2107 - Rev. 2.0 Programmable Interrupt Timer Modules (PIT1 and PIT2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Programmable Interrupt Timer Modules (PIT1 and PIT2) Memory Map and Registers 14.6.2.1 PIT Control and Status Register Address: PIT1 -- 0x00c8_0000 and 0x00c8_0001 PIT2 -- 0x00c9_0000 and 0x00c9_0001 Read: Bit 15 14 13 12 0 0 0 0 11 10 9 Bit 8 PRE3 PRE2 PRE1 PRE0 Write: Freescale Semiconductor, Inc... Reset: Read: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 PDOZE PDBG OVW PIE PIF RLD EN 0 0 0 0 0 0 0 0 Write: Reset: 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 14-2. PIT Control and Status Register (PCSR) PRE[3:0] -- Prescaler Bits The read/write PRE[3:0] bits select the system clock divisor to generate the PIT clock as Table 14-2 shows. To accurately predict the timing of the next count, change the PRE[3:0] bits only when the enable bit (EN) is clear. Changing the PRE[3:0] resets the prescaler counter. System reset and the loading of a new value into the counter also reset the prescaler counter. Setting the EN bit and writing to PRE[3:0] can be done in this same write cycle. Clearing the EN bit stops the prescaler counter. PDOZE -- Doze Mode Bit The read/write PDOZE bit controls the function of the PIT in doze mode. Reset clears PDOZE. 1 = PIT function stopped in doze mode 0 = PIT function not affected in doze mode When doze mode is exited, timer operation continues from the state it was in before entering doze mode. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Programmable Interrupt Timer Modules (PIT1 and PIT2) For More Information On This Product, Go to: www.freescale.com 285 Freescale Semiconductor, Inc. Programmable Interrupt Timer Modules (PIT1 and PIT2) Table 14-2. Prescaler Select Encoding Freescale Semiconductor, Inc... PRE[3:0] System Clock Divisor 0000 1 0001 2 0010 4 0011 8 0100 16 0101 32 0110 64 0111 128 1000 256 1001 512 1010 1,024 1011 2,048 1100 4,096 1101 8,192 1110 16,384 1111 32,768 PDBG -- Debug Mode Bit The read/write PDBG bit controls the function of the PIT in debug mode. Reset clears PDBG. 1 = PIT function stopped in debug mode 0 = PIT function not affected in debug mode During debug mode, register read and write accesses function normally. When debug mode is exited, timer operation continues from the state it was in before entering debug mode, but any updates made in debug mode remain. NOTE: Changing the PDBG bit from 1 to 0 during debug mode starts the PIT timer. Likewise, changing the PDBG bit from 0 to 1 during debug mode stops the PIT timer. Technical Data 286 MMC2107 - Rev. 2.0 Programmable Interrupt Timer Modules (PIT1 and PIT2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Programmable Interrupt Timer Modules (PIT1 and PIT2) Memory Map and Registers OVW -- Overwrite Bit The read/write OVW bit enables writing to PMR to immediately overwrite the value in the PIT counter. 1 = Writing PMR immediately replaces value in PIT counter. 0 = Value in PMR replaces value in PIT counter when count reaches 0x0000. PIE -- PIT Interrupt Enable Bit Freescale Semiconductor, Inc... The read/write PIE bit enables the PIF flag to generate interrupt requests. 1 = PIF interrupt requests enabled 0 = PIF interrupt requests disabled PIF -- PIT Interrupt Flag The read/write PIF flag is set when the PIT counter reaches 0x0000. Clear PIF by writing a 1 to it or by writing to PMR. Writing 0 has no effect. Reset clears PIF. 1 = PIT count has reached 0x0000. 0 = PIT count has not reached 0x0000. RLD -- Reload Bit The read/write RLD bit enables loading the value of PMR into the PIT counter when the count reaches 0x0000. 1 = Counter reloaded from PMR on count of 0x0000 0 = Counter rolls over to 0xFFFF on count of 0x0000 EN -- PIT Enable Bit The read/write EN bit enables PIT operation. When the PIT is disabled, the counter and prescaler are held in a stopped state. 1 = PIT enabled 0 = PIT disabled MMC2107 - Rev. 2.0 MOTOROLA Technical Data Programmable Interrupt Timer Modules (PIT1 and PIT2) For More Information On This Product, Go to: www.freescale.com 287 Freescale Semiconductor, Inc. Programmable Interrupt Timer Modules (PIT1 and PIT2) 14.6.2.2 PIT Modulus Register The 16-bit read/write PIT modulus register (PMR) contains the timer modulus value for loading into the PIT counter when the count reaches 0x0000 and the RLD bit is set. Freescale Semiconductor, Inc... When the OVW bit is set, PMR is transparent, and the value written to PMR is immediately loaded into the PIT counter. The prescaler counter is reset anytime a new value is loaded into the PIT counter and also during reset. Reading the PMR returns the value written in the modulus latch. Reset initializes PMR to 0xFFFF. Address: PIT1 -- 0x00c8_0002 and 0x00c8_0003 PIT2 -- 0x00c9_0002 and 0x00c9_0003 Bit 15 14 13 12 11 10 9 Bit 8 PM15 PM14 PM13 PM12 PM11 PM10 PM9 PM8 1 1 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 PM7 PM6 PM5 PM4 PM3 PM2 PM1 PM0 1 1 1 1 1 1 1 1 Read: Write: Reset: Read: Write: Reset: Figure 14-3. PIT Modulus Register (PMR) Technical Data 288 MMC2107 - Rev. 2.0 Programmable Interrupt Timer Modules (PIT1 and PIT2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Programmable Interrupt Timer Modules (PIT1 and PIT2) Memory Map and Registers 14.6.2.3 PIT Count Register The 16-bit, read-only PIT control register (PCNTR) contains the counter value. Reading the 16-bit counter with two 8-bit reads is not guaranteed to be coherent. Writing to PCNTR has no effect, and write cycles are terminated normally. Freescale Semiconductor, Inc... Address: PIT1 -- 0x00c8_0004 and 0x00c8_0005 PIT2 -- 0x00c9_0004 and 0x00c9_0005 Read: Bit 15 14 13 12 11 10 9 Bit 8 PC15 PC14 PC13 PC12 PC11 PC10 PC9 PC8 1 1 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 1 1 1 1 1 1 1 1 Write: Reset: Read: Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 14-4. PIT Count Register (PCNTR) MMC2107 - Rev. 2.0 MOTOROLA Technical Data Programmable Interrupt Timer Modules (PIT1 and PIT2) For More Information On This Product, Go to: www.freescale.com 289 Freescale Semiconductor, Inc. Programmable Interrupt Timer Modules (PIT1 and PIT2) 14.7 Functional Description This subsection describes the PIT functional operation. 14.7.1 Set-and-Forget Timer Operation This mode of operation is selected when the RLD bit in the PCSR register is set. Freescale Semiconductor, Inc... When the PIT counter reaches a count of 0x0000, the PIF flag is set in PCSR. The value in the modulus latch is loaded into the counter, and the counter begins decrementing toward 0x0000. If the PIE bit is set in PCSR, the PIF flag issues an interrupt request to the CPU. When the OVW bit is set in PCSR, the counter can be directly initialized by writing to PMR without having to wait for the count to reach 0x0000. PIT CLOCK COUNTER MODULUS 0x0002 0x0001 0x0000 0x0005 0x0005 PIF Figure 14-5. Counter Reloading from the Modulus Latch Technical Data 290 MMC2107 - Rev. 2.0 Programmable Interrupt Timer Modules (PIT1 and PIT2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Programmable Interrupt Timer Modules (PIT1 and PIT2) Functional Description 14.7.2 Free-Running Timer Operation This mode of operation is selected when the RLD bit in PCSR is clear. In this mode, the counter rolls over from 0x0000 to 0xFFFF without reloading from the modulus latch and continues to decrement. Freescale Semiconductor, Inc... When the counter reaches a count of 0x0000, the PIF flag is set in PCSR. If the PIE bit is set in PCSR, the PIF flag issues an interrupt request to the CPU. When the OVW bit is set in PCSR, the counter can be directly initialized by writing to PMR without having to wait for the count to reach 0x0000. PIT CLOCK COUNTER 0x0002 MODULUS 0x0001 0x0000 0xFFFF 0x0005 PIF Figure 14-6. Counter in Free-Running Mode 14.7.3 Timeout Specifications The 16-bit PIT counter and prescaler supports different timeout periods. The prescaler divides the system clock as selected by the PRE[3:0] bits in PCSR. The PM[15:0] bits in PMR select the timeout period. timeout period = PRE[3:0] x (PM[15:0] + 1) clocks MMC2107 - Rev. 2.0 MOTOROLA Technical Data Programmable Interrupt Timer Modules (PIT1 and PIT2) For More Information On This Product, Go to: www.freescale.com 291 Freescale Semiconductor, Inc. Programmable Interrupt Timer Modules (PIT1 and PIT2) 14.8 Interrupt Operation Table 14-3 lists the interrupt requests generated by the PIT. Table 14-3. PIT Interrupt Requests Interrupt Request Flag Enable Bit Timeout PIF PIE Freescale Semiconductor, Inc... The PIF flag is set when the PIT counter reaches 0x0000. The PIE bit enables the PIF flag to generate interrupt requests. Clear PIF by writing a 1 to it or by writing to the PMR. Technical Data 292 MMC2107 - Rev. 2.0 Programmable Interrupt Timer Modules (PIT1 and PIT2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 15. Timer Modules (TIM1 and TIM2) Freescale Semiconductor, Inc... 15.1 Contents 15.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295 15.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295 15.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296 15.5 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .297 15.5.1 Supervisor and User Modes. . . . . . . . . . . . . . . . . . . . . . . . 297 15.5.2 Run Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297 15.5.3 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .297 15.5.4 Wait, Doze, and Debug Modes . . . . . . . . . . . . . . . . . . . . . 297 15.5.5 Test Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .297 15.6 Signal Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298 15.6.1 ICOC[2:0] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298 15.6.2 ICOC3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298 15.7 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 298 15.7.1 Timer Input Capture/Output Compare Select Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 15.7.2 Timer Compare Force Register . . . . . . . . . . . . . . . . . . . . . 301 15.7.3 Timer Output Compare 3 Mask Register . . . . . . . . . . . . . . 302 15.7.4 Timer Output Compare 3 Data Register. . . . . . . . . . . . . . . 303 15.7.5 Timer Counter Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 304 15.7.6 Timer System Control Register 1 . . . . . . . . . . . . . . . . . . . . 305 15.7.7 Timer Toggle-On-Overflow Register . . . . . . . . . . . . . . . . . 306 15.7.8 Timer Control Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . 307 15.7.9 Timer Control Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . 308 15.7.10 Timer Interrupt Enable Register . . . . . . . . . . . . . . . . . . . . . 309 15.7.11 Timer System Control Register 2 . . . . . . . . . . . . . . . . . . . . 310 15.7.12 Timer Flag Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312 15.7.13 Timer Flag Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313 15.7.14 Timer Channel Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 314 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com 293 Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) 15.7.15 15.7.16 15.7.17 15.7.18 15.7.19 15.7.20 Pulse Accumulator Control Register . . . . . . . . . . . . . . . . . 315 Pulse Accumulator Flag Register . . . . . . . . . . . . . . . . . . . . 317 Pulse Accumulator Counter Registers . . . . . . . . . . . . . . . . 318 Timer Port Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . 319 Timer Port Data Direction Register . . . . . . . . . . . . . . . . . .320 Timer Test Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321 Freescale Semiconductor, Inc... 15.8 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321 15.8.1 Prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321 15.8.2 Input Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321 15.8.3 Output Compare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .322 15.8.4 Pulse Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323 15.8.4.1 Event Counter Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 323 15.8.4.2 Gated Time Accumulation Mode . . . . . . . . . . . . . . . . . .324 15.8.5 General-Purpose I/O Ports. . . . . . . . . . . . . . . . . . . . . . . . . 325 15.9 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326 15.10 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326 15.10.1 Timer Channel Interrupts (CxF) . . . . . . . . . . . . . . . . . . . . . 326 15.10.2 Pulse Accumulator Overflow (PAOVF). . . . . . . . . . . . . . . . 327 15.10.3 Pulse Accumulator Input (PAIF) . . . . . . . . . . . . . . . . . . . . . 327 15.10.4 Timer Overflow (TOF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327 Technical Data 294 MMC2107 - Rev. 2.0 Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) Introduction 15.2 Introduction Freescale Semiconductor, Inc... The MMC2107 has two 4-channel timer modules (TIM1 and TIM2). Each consists of a 16-bit programmable counter driven by a 7-stage programmable prescaler. Each of the four timer channels can be configured for input capture or output. Additionally, one of the channels, channel 3, can be configured as a pulse accumulator. A timer overflow function allows software to extend the timing capability of the system beyond the 16-bit range of the counter. The input capture and output compare functions allow simultaneous input waveform measurements and output waveform generation. The input capture function can capture the time of a selected transition edge. The output compare function can generate output waveforms and timer software delays. The 16-bit pulse accumulator can operate as a simple event counter or a gated time accumulator. The pulse accumulator shares timer channel 3 when in event mode. 15.3 Features Features of the timer include: * Four 16-bit input capture/output compare channels * 16-bit architecture * Programmable prescaler * Pulse widths variable from microseconds to seconds * Single 16-bit pulse accumulator * Toggle-on-overflow feature for pulse-width modulator (PWM) generation * Option for enabling timer port pullups on reset MMC2107 - Rev. 2.0 MOTOROLA Technical Data Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com 295 Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) 15.4 Block Diagram CLK[1:0] PR[2:0] PACLK PACLK/256 PACLK/65536 SYSTEM CLOCK CHANNEL 3 OUTPUT COMPARE MUX PRESCALER TCRE CxI TIMCNTH:TIMCNTL CxF Freescale Semiconductor, Inc... CLEAR COUNTER 16-BIT COUNTER TOF INTERRUPT LOGIC TOI TE INTERRUPT REQUEST CHANNEL 0 16-BIT COMPARATOR EDGE DETECT C0F IOS0 TIMC0H:TIMC0L 16-BIT LATCH EDG0A OM:OL0 EDG0B TOV0 CH. 0 CAPTURE PT0 LOGIC CH. 0 COMPARE ICOC0 PIN CHANNEL 1 16-BIT COMPARATOR EDGE DETECT C1F IOS1 TIMC1H:TIMC1L 16-BIT LATCH EDG1A OM:OL1 EDG1B TOV1 CH. 1 CAPTURE PT1 LOGIC CH. 1 COMPARE ICOC1 PIN CHANNEL 2 CHANNEL3 16-BIT COMPARATOR EDGE DETECT C3F IOS3 TIMC3H:TIMC3L 16-BIT LATCH EDG3A OM:OL3 EDG3B TOV3 PEDGE PAOVF TIMPACNTH:TIMPACNTL PACLK/65536 PAE INTERRUPT REQUEST INTERRUPT LOGIC CH. 3 COMPARE ICOC3 PIN PAIF DIVIDE-BY-64 PACLK CH.3 CAPTURE PA INPUT EDGE DETECT MUX 16-BIT COUNTER PACLK/256 PT3 LOGIC MODULE CLOCK PAMOD PAOVI PAI PAOVF PAIF Figure 15-1. Timer Block Diagram Technical Data 296 MMC2107 - Rev. 2.0 Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) Modes of Operation 15.5 Modes of Operation This subsection describes the supervisor and user modes, the five low-power options, and test mode. Freescale Semiconductor, Inc... 15.5.1 Supervisor and User Modes The SO bit in the chip-select control register determines whether the processor is operating in user mode or supervisor mode. Accessing supervisor address locations while not in supervisor mode causes the timer to assert a transfer error. 15.5.2 Run Mode Clearing the TIMEN bit in the timer system control register 1 (TIMSCR1) or the PAE bit in the pulse accumulator control register (TIMPACTL) reduces power consumption in run mode. Timer registers are still accessible, but all timer functions are disabled. 15.5.3 Stop Mode If the central processor unit (CPU) enters stop mode, timer operation stops. Upon exiting stop mode, the timer resumes operation unless stop mode was exited by reset. 15.5.4 Wait, Doze, and Debug Modes The timer is unaffected by these low-power modes. 15.5.5 Test Mode A high signal on the TEST pin puts the processor in test mode or special mode. The timer behaves as in user mode, except that timer test registers are accessible. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com 297 Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) 15.6 Signal Description Table 15-1 provides an overview of the signal properties. Freescale Semiconductor, Inc... Table 15-1. Signal Properties Name(1) Port ICOC0 TIMPORT0 ICOC1 Function Reset State Pullup Channel 0 IC/OC pin Pin state Active TIMPORT1 Timer channel 1 IC/OC pin Pin state Active ICOC2 TIMPORT2 Timer channel 2 IC/OC pin Pin state Active ICOC3 TIMPORT3 Timer channel 3 IC/OC or PA pin Pin state Active 1. Pin signal names may change according to user requirements. 15.6.1 ICOC[2:0] The ICOC[2:0] pins are for channel 2-0 input capture and output compare functions. These pins are available for general-purpose input/output (I/O) when not configured for timer functions. 15.6.2 ICOC3 The ICOC3 pin is for channel 3 input capture and output compare functions or for the pulse accumulator input. This pin is available for general-purpose I/O when not configured for timer functions. 15.7 Memory Map and Registers See Table 15-2 for a memory map of the two timer modules. Timer 1 has a base address of 0x00ce_0000. Timer 2 has a base address of 0x00cf_0000. NOTE: Reading reserved or unimplemented locations returns 0s. Writing to reserved or unimplemented locations has no effect. Technical Data 298 MMC2107 - Rev. 2.0 Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) Memory Map and Registers Table 15-2. Timer Modules Memory Map Freescale Semiconductor, Inc... Address Bits 7-0 Access(1) 0x00cf_0000 Timer IC/OC select register (TIMIOS) S 0x00ce_0001 0x00cf_0001 Timer compare force register (TIMCFORC) S 0x00ce_0002 0x00cf_0002 Timer output compare 3 mask register (TIMOC3M) S 0x00ce_0003 0x00cf_0003 Timer output compare 3 data register (TIMOC3D) S 0x00ce_0004 0x00cf_0004 Timer counter register high (TIMCNTH) S 0x00ce_0005 0x00cf_0005 Timer counter register low (TIMCNTL) S 0x00ce_0006 0x00cf_0006 Timer system control register 1 (TIMSCR1) S 0x00ce_0007 0x00cf_0007 Reserved (2) -- 0x00ce_0008 0x00cf_0008 Timer toggle-on-overflow register (TMTOV) S 0x00ce_0009 0x00cf_0009 Timer control register 1 (TIMCTL1) S 0x00ce_000a 0x00cf_000a Reserved (2) -- 0x00ce_000b 0x00cf_000b Timer control register 2 (TIMCTL2) S 0x00ce_000c 0x00cf_000c Timer interrupt enable register (TIMIE) S 0x00ce_000d 0x00cf_000d Timer system control register 2 (TIMSCR2) S 0x00ce_000e 0x00cf_000e Timer flag register 1 (TIMFLG1) S 0x00ce_000f 0x00cf_000f Timer flag register 2 (TIMFLG2) S 0x00ce_0010 0x00cf_0010 Timer channel 0 register high (TIMC0H) S 0x00ce_0011 0x00cf_0011 Timer channel 0 register low (TIMC0L) S 0x00ce_0012 0x00cf_0012 Timer channel 1 register high (TIMC1H) S 0x00ce_0013 0x00cf_0013 Timer channel 1 register low (TIMC1L) S 0x00ce_0014 0x00cf_0014 Timer channel 2 register high (TIMC2H) S 0x00ce_0015 0x00cf_0015 Timer channel 2 register low (TIMC2L) S 0x00ce_0016 0x00cf_0016 Timer channel 3 register high (TIMC3H) S 0x00ce_0017 0x00cf_0017 Timer channel 3 register low (TIMC3L) S 0x00ce_0018 0x00cf_0018 Pulse accumulator control register (TIMPACTL) S 0x00ce_0019 0x00cf_0019 Pulse accumulator flag register (TIMPAFLG) S 0x00ce_001a 0x00cf_001a Pulse accumulator counter register high (TIMPACNTH) S 0x00ce_001b 0x00cf_001b Pulse accumulator counter register low (TIMPACNTL) S 0x00ce_001c 0x00cf_001c Reserved (2) -- 0x00ce_001d 0x00cf_001d Timer port data register (TIMPORT) S 0x00ce_001e 0x00cf_001e Timer port data direction register (TIMDDR) S 0x00ce_001f 0x00cf_001f Timer test register (TIMTST) S TIM1 TIM2 0x00ce_0000 1. S = CPU supervisor mode access only. 2. Writes have no effect, reads return 0s, and the access terminates without a transfer error exception. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com 299 Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) 15.7.1 Timer Input Capture/Output Compare Select Register Address: TIM1 -- 0x00ce_0000 TIM2 -- 0x00cf_0000 Read: Bit 7 6 5 4 0 0 0 0 3 2 1 Bit 0 IOS3 IOS2 IOS1 IOS0 0 0 0 0 Write: Reset: 0 0 0 0 Freescale Semiconductor, Inc... = Writes have no effect and the access terminates without a transfer error exception. Figure 15-2. Timer Input Capture/Output Compare Select Register (TIMIOS) Read: Anytime; always read $00 Write: Anytime IOS[3:0] -- I/O Select Bits The IOS[3:0] bits enable input capture or output compare operation for the corresponding timer channels. 1 = Output compare enabled 0 = Input capture enabled Technical Data 300 MMC2107 - Rev. 2.0 Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) Memory Map and Registers 15.7.2 Timer Compare Force Register Address: TIM1 -- 0x00ce_0001 TIM2 -- 0x00cf_0001 Read: Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 FOC3 FOC2 FOC1 FOC0 0 0 0 0 Write: Freescale Semiconductor, Inc... Reset: 0 0 0 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 15-3. Timer Compare Force Register (TIMCFORC) Read: Anytime Write: Anytime FOC[3:0] -- Force Output Compare Bits Setting an FOC bit causes an immediate output compare on the corresponding channel. Forcing an output compare does not set the output compare flag. 1 = Force output compare 0 = No effect NOTE: A successful channel 3 output compare overrides any channel 2:0 compares. For each OC3M bit that is set, the output compare action reflects the corresponding OC3D bit. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com 301 Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) 15.7.3 Timer Output Compare 3 Mask Register Address: TIM1 -- 0x00ce_0002 TIM2 -- 0x00cf_0002 Read: Bit 7 6 5 4 0 0 0 0 3 2 1 Bit 0 OC3M3 OC3M2 OC3M1 OC3M0 0 0 0 0 Write: Freescale Semiconductor, Inc... Reset: 0 0 0 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 15-4. Timer Output Compare 3 Mask Register (TIMOC3M) Read: Anytime Write: Anytime OC3M[3:0] -- Output Compare 3 Mask Bits Setting an OC3M bit configures the corresponding TIMPORT pin to be an output. OC3Mx makes the timer port pin an output regardless of the data direction bit when the pin is configured for output compare (IOSx = 1). The OC3Mx bits do not change the state of the TIMDDR bits. 1 = Corresponding TIMPORT pin configured as output 0 = No effect Technical Data 302 MMC2107 - Rev. 2.0 Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) Memory Map and Registers 15.7.4 Timer Output Compare 3 Data Register Address: TIM1 -- 0x00ce_0003 TIM2 -- 0x00cf_0003 Read: Bit 7 6 5 4 0 0 0 0 3 2 1 Bit 0 OC3D3 OC3D2 OC3D1 OC3D0 0 0 0 0 Write: Freescale Semiconductor, Inc... Reset: 0 0 0 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 15-5. Timer Output Compare 3 Data Register (TIMOC3D) Read: Anytime Write: Anytime OC3D[3:0] -- Output Compare 3 Data Bits When a successful channel 3 output compare occurs, these bits transfer to the timer port data register if the corresponding OC3Mx bits are set. NOTE: A successful channel 3 output compare overrides any channel 2:0 compares. For each OC3M bit that is set, the output compare action reflects the corresponding OC3D bit. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com 303 Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) 15.7.5 Timer Counter Registers Address: TIM1 -- 0x00ce_0004 TIM2 -- 0x00cf_0004 Read: Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 Write: Freescale Semiconductor, Inc... Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 15-6. Timer Counter Register High (TIMCNTH) Address: TIM1 -- 0x00ce_0005 TIM2 -- 0x00cf_0005 Read: Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 15-7. Timer Counter Register Low (TIMCNTL) Read: Anytime Write: Only in test (special) mode; has no effect in normal modes To ensure coherent reading of the timer counter, such that a timer rollover does not occur between two back-to-back 8-bit reads, it is recommended that only half-word (16-bit) accesses be used. A write to TIMCNT may have an extra cycle on the first count because the write is not synchronized with the prescaler clock. The write occurs at least one cycle before the synchronization of the prescaler clock. Technical Data 304 MMC2107 - Rev. 2.0 Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) Memory Map and Registers 15.7.6 Timer System Control Register 1 Address: TIM1 -- 0x00ce_0006 TIM2 -- 0x00cf_0006 Bit 7 Read: 6 5 0 0 TIMEN 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 TFFCA Write: Reset: 0 0 0 0 Freescale Semiconductor, Inc... = Writes have no effect and the access terminates without a transfer error exception. Figure 15-8. Timer System Control Register (TIMSCR1) Read: Anytime Write: Anytime TIMEN -- Timer Enable Bit TIMEN enables the timer. When the timer is disabled, only the registers are accessible. Clearing TIMEN reduces power consumption. 1 = Timer enabled 0 = Timer and timer counter disabled TFFCA -- Timer Fast Flag Clear All Bit TFFCA enables fast clearing of the main timer interrupt flag registers (TIMFLG1 and TIMFLG2) and the PA flag register (TIMPAFLG). TFFCA eliminates the software overhead of a separate clear sequence. When TFFCA is set: - An input capture read or a write to an output compare channel clears the corresponding channel flag, CxF. - Any access of the timer count registers (TIMCNTH/L) clears the TOF flag. - Any access of the PA counter registers (TIMPACNT) clears both the PAOVF and PAIF flags in TIMPAFLG. Writing logic 1s to the flags clears them only when TFFCA is clear. 1 = Fast flag clearing 0 = Normal flag clearing MMC2107 - Rev. 2.0 MOTOROLA Technical Data Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com 305 Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) WRITE TIMFLG1 REGISTER DATA BIT x CxF CLEAR CxF FLAG TFFCA READ TIMCx REGISTERS Freescale Semiconductor, Inc... WRITE TIMCx REGISTERS Figure 15-9. Fast Clear Flag Logic 15.7.7 Timer Toggle-On-Overflow Register Address: TIM1 -- 0x00ce_0008 TIM2 -- 0x00cf_0008 Read: Bit 7 6 5 4 0 0 0 0 3 2 1 Bit 0 TOV3 TOV2 TOV1 TOV0 0 0 0 0 Write: Reset: 0 0 0 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 15-10. Timer Toggle-On-Overflow Register (TIMTOV) Read: Anytime Write: Anytime TOV[3:0]-- Toggle-On-Overflow Bits TOV[3:0] toggles the output compare pin on overflow. This feature only takes effect when in output compare mode. When set, it takes precedence over forced output compare but not channel 3 override events. 1 = Toggle output compare pin on overflow feature enabled 0 = Toggle output compare pin on overflow feature disabled Technical Data 306 MMC2107 - Rev. 2.0 Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) Memory Map and Registers 15.7.8 Timer Control Register 1 Address: TIM1 -- 0x00ce_0009 TIM2 -- 0x00cf_0009 Bit 7 6 5 4 3 2 1 Bit 0 OM3 OL3 OM2 OL2 OM1 OL1 OM0 OL0 0 0 0 0 0 0 0 0 Read: Write: Reset: Freescale Semiconductor, Inc... = Writes have no effect and the access terminates without a transfer error exception. Figure 15-11. Timer Control Register 1 (TIMCTL1) Read: Anytime Write: Anytime OMx/OLx -- Output Mode/Output Level Bits These bit pairs select the output action to be taken as a result of a successful output compare. When either OMx or OLx is set and the IOSx bit is set, the pin is an output regardless of the state of the corresponding DDR bit. Table 15-3. Output Compare Action Selection OMx:OLx Action on Output Compare 00 Timer disconnected from output pin logic 01 Toggle OCx output line 10 Clear OCx output line 11 Set OCx line Channel 3 shares a pin with the pulse accumulator input pin. To use the PAI input, clear both the OM3 and OL3 bits and clear the OC3M3 bit in the output compare 3 mask register. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com 307 Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) 15.7.9 Timer Control Register 2 Address: TIM1 -- 0x00ce_000b TIM2 -- 0x00cf_000b Bit 7 6 5 4 3 2 1 Bit 0 EDG3B EDG3A EDG2B EDG2A EDG1B EDG1A EDG0B EDG10 0 0 0 0 0 0 0 0 Read: Write: Reset: Freescale Semiconductor, Inc... = Writes have no effect and the access terminates without a transfer error exception. Figure 15-12. Timer Control Register 2 (TIMCTL2) Read: Anytime Write: Anytime EDGx[B:A] -- Input Capture Edge Control Bits These eight bit pairs configure the input capture edge detector circuits. Table 15-4. Input Capture Edge Selection EDGx[B:A] Edge Selection 00 Input capture disabled 01 Input capture on rising edges only 10 Input capture on falling edges only 11 Input capture on any edge (rising or falling) Technical Data 308 MMC2107 - Rev. 2.0 Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) Memory Map and Registers 15.7.10 Timer Interrupt Enable Register Address: TIM1 -- 0x00ce_000c TIM2 -- 0x00cf_000c Read: Bit 7 6 5 4 0 0 0 0 3 2 1 Bit 0 C3I C2I C1I C0I 0 0 0 0 Write: Reset: 0 0 0 0 Freescale Semiconductor, Inc... = Writes have no effect and the access terminates without a transfer error exception. Figure 15-13. Timer Interrupt Enable Register (TIMIE) Read: Anytime Write: Anytime C[3:0]I -- Channel Interrupt Enable Bits C[3:0]I enable the C[3:0]F flags in timer flag register 1 to generate interrupt requests. 1 = Corresponding channel interrupt requests enabled 0 = Corresponding channel interrupt requests disabled MMC2107 - Rev. 2.0 MOTOROLA Technical Data Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com 309 Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) 15.7.11 Timer System Control Register 2 Address: TIM1 -- 0x00ce_000d TIM2 -- 0x00cf_000d Bit 7 6 Read: 5 4 3 2 1 Bit 0 PUPT RDPT TCRE PR2 PR1 PR0 0 0 0 0 0 0 0 TOI Write: Reset: 0 0 Freescale Semiconductor, Inc... = Writes have no effect and the access terminates without a transfer error exception. Figure 15-14. Timer System Control Register 2 (TIMSCR2) Read: Anytime Write: Anytime TOI -- Timer Overflow Interrupt Enable Bit TOI enables timer overflow interrupt requests. 1 = Overflow interrupt requests enabled 0 = Overflow interrupt requests disabled PUPT -- Timer Pullup Enable Bit PUPT enables pullup resistors on the timer ports when the ports are configured as inputs. 1 = Pullup resistors enabled 0 = Pullup resistors disabled RDPT -- Timer Drive Reduction Bit RDPT reduces the output driver size. 1 = Output drive reduction enabled 0 = Output drive reduction disabled TCRE -- Timer Counter Reset Enable Bit TCRE enables a counter reset after a channel 3 compare. 1 = Counter reset enabled 0 = Counter reset disabled NOTE: When the timer channel 3 registers contain $0000 and TCRE is set, the timer counter registers remain at $0000 all the time. Technical Data 310 MMC2107 - Rev. 2.0 Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) Memory Map and Registers When the timer channel 3 registers contain $FFFF and TCRE is set, TOF never gets set even though the timer counter registers go from $FFFF to $0000. PR[2:0] -- Prescaler Bits These bits select the prescaler divisor for the timer counter. Freescale Semiconductor, Inc... Table 15-5. Prescaler Selection NOTE: PR[2:0] Prescaler Divisor 000 1 001 2 010 4 011 8 100 16 101 32 110 64 111 128 The newly selected prescaled clock does not take effect until the next synchronized edge of the prescaled clock when the clock count transitions to $0000.) MMC2107 - Rev. 2.0 MOTOROLA Technical Data Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com 311 Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) 15.7.12 Timer Flag Register 1 Address: TIM1 -- 0x00ce_000e TIM2 -- 0x00cf_000e Read: Bit 7 6 5 4 0 0 0 0 3 2 1 Bit 0 C3F C2F C1F C0F 0 0 0 0 Write: Reset: 0 0 0 0 Freescale Semiconductor, Inc... = Writes have no effect and the access terminates without a transfer error exception. Figure 15-15. Timer Flag Register 1 (TIMFLG1) Read: Anytime Write: Anytime; writing 1 clears flag; writing 0 has no effect C[3:0]F -- Channel Flags A channel flag is set when an input capture or output compare event occurs. Clear a channel flag by writing a 1 to it. NOTE: When the fast flag clear all bit, TFFCA, is set, an input capture read or an output compare write clears the corresponding channel flag. TFFCA is in timer system control register 1 (TIMSCR1). When a channel flag is set, it does not inhibit subsequent output compares or input captures. Technical Data 312 MMC2107 - Rev. 2.0 Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) Memory Map and Registers 15.7.13 Timer Flag Register 2 Address: TIM1 -- 0x00ce_000f TIM2 -- 0x00cf_000f Bit 7 Read: 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 TOF Write: Reset: 0 Freescale Semiconductor, Inc... = Writes have no effect and the access terminates without a transfer error exception. Figure 15-16. Timer Flag Register 2 (TIMFLG2) Read: Anytime Write: Anytime; writing 1 clears flag; writing 0 has no effect TOF -- Timer Overflow Flag TOF is set when the timer counter rolls over from $FFFF to $0000. If the TOI bit in TIMSCR2 is also set, TOF generates an interrupt request. Clear TOF by writing a 1 to it. 1 = Timer overflow 0 = No timer overflow NOTE: When the timer channel 3 registers contain $FFFF and TCRE is set, TOF never gets set even though the timer counter registers go from $FFFF to $0000. When the fast flag clear all bit, TFFCA, is set, any access to the timer counter registers clears timer flag register 2. The TFFCA bit is in timer system control register 1 (TIMSCR1). When TOF is set, it does not inhibit subsequent overflow events. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com 313 Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) 15.7.14 Timer Channel Registers Address: TIMC0H -- 0x00ce_0010/0x00cf_0010 TIMC1H -- 0x00ce_0012/0x00cf_0012 TIMC2H -- 0x00ce_0014/0x00cf_0014 TIMC3H -- 0x00ce_0016/0x00cf_0016 Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 Read: Write: Freescale Semiconductor, Inc... Reset: Figure 15-17. Timer Channel [0:3] Register High (TIMCxH) Address: TIMC0L -- 0x00ce_0011/0x00cf_0011 TIMC1L -- 0x00ce_0013/0x00cf_0013 TIMC2L -- 0x00ce_0015/0x00cf_0015 TIMC3L -- 0x00ce_0017/0x00cf_0017 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 Read: Write: Reset: Figure 15-18. Timer Channel [0:3] Register Low (TIMCxL) Read: Anytime Write: Output compare channel, anytime; input capture channel, no effect When a channel is configured for input capture (IOSx = 0), the timer channel registers latch the value of the free-running counter when a defined transition occurs on the corresponding input capture pin. When a channel is configured for output compare (IOSx = 1), the timer channel registers contain the output compare value. To ensure coherent reading of the timer counter, such that a timer rollover does not occur between back-to-back 8-bit reads, it is recommended that only half-word (16-bit) accesses be used. Technical Data 314 MMC2107 - Rev. 2.0 Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) Memory Map and Registers 15.7.15 Pulse Accumulator Control Register Address: TIM1 -- 0x00ce_0018 TIM2 -- 0x00cf_0018 Bit 7 Read: 6 5 4 3 2 1 Bit 0 PAE PAMOD PEDGE CLK1 CLK0 PAOVI PAI 0 0 0 0 0 0 0 0 Write: Reset: 0 Freescale Semiconductor, Inc... = Writes have no effect and the access terminates without a transfer error exception. Figure 15-19. Pulse Accumulator Control Register (TIMPACTL) Read: Anytime Write: Anytime PAE -- Pulse Accumulator Enable Bit PAE enables the pulse accumulator. 1 = Pulse accumulator enabled 0 = Pulse accumulator disabled NOTE: The pulse accumulator can operate in event mode even when the timer enable bit, TIMEN, is clear. PAMOD -- Pulse Accumulator Mode Bit PAMOD selects event counter mode or gated time accumulation mode. 1 = Gated time accumulation mode 0 = Event counter mode PEDGE -- Pulse Accumulator Edge Bit PEDGE selects falling or rising edges on the PAI pin to increment the counter. In event counter mode (PAMOD = 0): 1 = Rising PAI edge increments counter 0 = Falling PAI edge increments counter MMC2107 - Rev. 2.0 MOTOROLA Technical Data Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com 315 Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) In gated time accumulation mode (PAMOD = 1): 1 = Low PAI input enables divided-by-64 clock to pulse accumulator and trailing rising edge on PAI sets PAIF flag. 0 = High PAI input enables divided-by-64 clock to pulse accumulator and trailing falling edge on PAI sets PAIF flag. NOTE: The timer prescaler generates the divided-by-64 clock. If the timer is not active, there is no divided-by-64 clock. To operate in gated time accumulation mode: Freescale Semiconductor, Inc... 1. Apply logic 0 to RESET pin. 2. Initialize registers for pulse accumulator mode test. 3. Apply appropriate level to PAI pin. 4. Enable timer. CLK[1:0] -- Clock Select Bits CLK[1:0] select the timer counter input clock as shown in Table 15-6. Table 15-6. Clock Selection CLK[1:0] Timer Counter Clock(1) 00 Timer prescaler clock(2) 01 PACLK 10 PACLK/256 11 PACLK/65536 1. Changing the CLKx bits causes an immediate change in the timer counter clock input. 2. When PAE = 0, the timer prescaler clock is always the timer counter clock. PAOVI -- Pulse Accumulator Overflow Interrupt Enable Bit PAOVI enables the PAOVF flag to generate interrupt requests. 1 = PAOVF interrupt requests enabled 0 = PAOVF interrupt requests disabled PAI -- Pulse Accumulator Input Interrupt Enable Bit PAI enables the PAIF flag to generate interrupt requests. 1 = PAIF interrupt requests enabled 0 = PAIF interrupt requests disabled Technical Data 316 MMC2107 - Rev. 2.0 Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) Memory Map and Registers 15.7.16 Pulse Accumulator Flag Register Address: TIM1 -- 0x00ce_0019 TIM2 -- 0x00cf_0019 Read: Bit 7 6 5 4 3 2 0 0 0 0 0 0 1 Bit 0 PAOVF PAIF 0 0 Write: Reset: 0 0 0 0 0 0 Freescale Semiconductor, Inc... = Writes have no effect and the access terminates without a transfer error exception. Figure 15-20. Pulse Accumulator Flag Register (TIMPAFLG) Read: Anytime Write: Anytime; writing 1 clears the flag; writing 0 has no effect PAOVF -- Pulse Accumulator Overflow Flag PAOVF is set when the 16-bit pulse accumulator rolls over from $FFFF to $0000. If the PAOVI bit in TIMPACTL is also set, PAOVF generates an interrupt request. Clear PAOVF by writing a 1 to it. 1 = Pulse accumulator overflow 0 = No pulse accumulator overflow PAIF -- Pulse Accumulator Input Flag PAIF is set when the selected edge is detected at the PAI pin. In event counter mode, the event edge sets PAIF. In gated time accumulation mode, the trailing edge of the gate signal at the PAI pin sets PAIF. If the PAI bit in TIMPACTL is also set, PAIF generates an interrupt request. Clear PAIF by writing a 1 to it. 1 = Active PAI input 0 = No active PAI input NOTE: When the fast flag clear all enable bit, TFFCA, is set, any access to the pulse accumulator counter registers clears all the flags in TIMPAFLG. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com 317 Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) 15.7.17 Pulse Accumulator Counter Registers Address: TIM1 -- 0x00ce_001a TIM2 -- 0x00cf_001a Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 Read: Write: Reset: Freescale Semiconductor, Inc... Figure 15-21. Pulse Accumulator Counter Register High (TIMPACNTH) Address: TIM1 -- 0x00ce_001b TIM2 -- 0x00cf_001b Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 Read: Write: Reset: Figure 15-22. Pulse Accumulator Counter Register Low (TIMPACNTL) Read: Anytime Write: Anytime These registers contain the number of active input edges on the PAI pin since the last reset. NOTE: Reading the pulse accumulator counter registers immediately after an active edge on the PAI pin may miss the last count since the input first has to be synchronized with the bus clock. To ensure coherent reading of the PA counter, such that the counter does not increment between back-to-back 8-bit reads, it is recommended that only half-word (16-bit) accesses be used. Technical Data 318 MMC2107 - Rev. 2.0 Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) Memory Map and Registers 15.7.18 Timer Port Data Register Address: TIM1 -- 0x00ce_001d TIM2 -- 0x00cf_001d Read: Bit 7 6 5 4 0 0 0 0 3 2 1 Bit 0 PORTT3 PORTT2 PORTT1 PORTT0 0 0 0 0 Write: Reset: 0 0 0 0 Freescale Semiconductor, Inc... = Writes have no effect and the access terminates without a transfer error exception. Figure 15-23. Timer Port Data Register (TIMPORT) Read: Anytime; read pin state when corresponding TIMDDR bit is 0; read pin driver state when corresponding TIMDDR bit is 1 Write: Anytime PORTT[3:0] -- Timer Port Input Capture/Output Compare Data Bits Data written to TIMPORT is buffered and drives the pins only when they are configured as general-purpose outputs. Reading an input (DDR bit = 0) reads the pin state; reading an output (DDR bit = 1) reads the latch. Writing to a pin configured as a timer output does not change the pin state. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com 319 Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) 15.7.19 Timer Port Data Direction Register Address: TIM1 -- 0x00ce_001e TIM2 -- 0x00cf_001e Read: Bit 7 6 5 4 0 0 0 0 3 2 1 Bit 0 DDRT3 DDRT2 DDRT1 DDRT0 0 0 0 0 IC/OC3 IC/OC2 IC/OC1 IC/OC0 Write: Reset: 0 0 Freescale Semiconductor, Inc... Timer function: Pulse accumulator function: 0 0 PAI = Writes have no effect and the access terminates without a transfer error exception. Figure 15-24. Timer Port Data Direction Register (TIMDDR) Read: Anytime Write: Anytime DDRT[3:0] -- TIMPORT Data Direction Bits These bits control the port logic of TIMPORT. Reset clears the timer port data direction register, configuring all timer port pins as inputs. 1 = Corresponding pin configured as output 0 = Corresponding pin configured as input Technical Data 320 MMC2107 - Rev. 2.0 Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) Functional Description 15.7.20 Timer Test Register The timer test register (TIMTST) is only for factory testing. When not in test mode, TIMTST is read-only. Address: TIM1 -- 0x00ce_001f TIM2 -- 0x00cf_001f Freescale Semiconductor, Inc... Read: Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 15-25. Timer Test Register (TIMTST) 15.8 Functional Description The timer module is a 16-bit, 4-channel timer with input capture and output compare functions and a pulse accumulator. 15.8.1 Prescaler The prescaler divides the module clock by 1, 2, 4, 8, 16, 32, 64, or 128. The PR[2:0] bits in TIMSCR2 select the prescaler divisor. 15.8.2 Input Capture Clearing an I/O select bit, IOSx, configures channel x as an input capture channel. The input capture function captures the time at which an external event occurs. When an active edge occurs on the pin of an input capture channel, the timer transfers the value in the timer counter into the timer channel registers, TIMCxH and TIMCxL. The minimum pulse width for the input capture input is greater than two module clocks. The input capture function does not force data direction. The timer port data direction register controls the data direction of an input capture pin. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com 321 Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) Pin conditions such as rising or falling edges can trigger an input capture only on a pin configured as an input. An input capture on channel x sets the CxF flag. The CxI bit enables the CxF flag to generate interrupt requests. 15.8.3 Output Compare Freescale Semiconductor, Inc... Setting an I/O select bit, IOSx, configures channel x as an output compare channel. The output compare function can generate a periodic pulse with a programmable polarity, duration, and frequency. When the timer counter reaches the value in the channel registers of an output compare channel, the timer can set, clear, or toggle the channel pin. An output compare on channel x sets the CxF flag. The CxI bit enables the CxF flag to generate interrupt requests. The output mode and level bits, OMx and OLx, select, set, clear, or toggle on output compare. Clearing both OMx and OLx disconnects the pin from the output logic. Setting a force output compare bit, FOCx, causes an output compare on channel x. A forced output compare does not set the channel flag. A successful output compare on channel 3 overrides output compares on all other output compare channels. A channel 3 output compare can cause bits in the output compare 3 data register to transfer to the timer port data register, depending on the output compare 3 mask register. The output compare 3 mask register masks the bits in the output compare 3 data register. The timer counter reset enable bit, TCRE, enables channel 3 output compares to reset the timer counter. A channel 3 output compare can reset the timer counter even if the OC3/PAI pin is being used as the pulse accumulator input. An output compare overrides the data direction bit of the output compare pin but does not change the state of the data direction bit. Writing to the timer port bit of an output compare pin does not affect the pin state. The value written is stored in an internal latch. When the pin becomes available for general-purpose output, the last value written to the bit appears at the pin. Technical Data 322 MMC2107 - Rev. 2.0 Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) Functional Description 15.8.4 Pulse Accumulator The pulse accumulator (PA) is a 16-bit counter that can operate in two modes: 1. Event counter mode -- Counts edges of selected polarity on the pulse accumulator input pin, PAI Freescale Semiconductor, Inc... 2. Gated time accumulation mode -- Counts pulses from a divide-by-64 clock The PA mode bit, PAMOD, selects the mode of operation. The minimum pulse width for the PAI input is greater than two module clocks. 15.8.4.1 Event Counter Mode Clearing the PAMOD bit configures the PA for event counter operation. An active edge on the PAI pin increments the PA. The PA edge bit, PEDGE, selects falling edges or rising edges to increment the PA. An active edge on the PAI pin sets the PA input flag, PAIF. The PA input interrupt enable bit, PAI, enables the PAIF flag to generate interrupt requests. NOTE: The PAI input and timer channel 3 use the same pin. To use the PAI input, disconnect it from the output logic by clearing the channel 3 output mode and output level bits, OM3 and OL3. Also clear the channel 3 output compare 3 mask bit, OC3M3. The PA counter registers, TIMPACNTH/L, reflect the number of active input edges on the PAI pin since the last reset. The PA overflow flag, PAOVF, is set when the PA rolls over from $FFFF to $0000. The PA overflow interrupt enable bit, PAOVI, enables the PAOVF flag to generate interrupt requests. NOTE: The PA can operate in event counter mode even when the timer enable bit, TIMEN, is clear. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com 323 Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) 15.8.4.2 Gated Time Accumulation Mode Setting the PAMOD bit configures the PA for gated time accumulation operation. An active level on the PAI pin enables a divide-by-64 clock to drive the PA. The PA edge bit, PEDGE, selects low levels or high levels to enable the divided-by-64 clock. The trailing edge of the active level at the PAI pin sets the PA input flag, PAIF. The PA input interrupt enable bit, PAI, enables the PAIF flag to generate interrupt requests. Freescale Semiconductor, Inc... NOTE: The PAI input and timer channel 3 use the same pin. To use the PAI input, disconnect it from the output logic by clearing the channel 3 output mode and output level bits, OM3 and OL3. Also clear the channel 3 output compare mask bit, OC3M3. The PA counter registers, TIMPACNTH/L reflect the number of pulses from the divide-by-64 clock since the last reset. NOTE: The timer prescaler generates the divide-by-64 clock. If the timer is not active, there is no divide-by-64 clock. PULSE ACCUMULATOR PAD CHANNEL 3 OUTPUT COMPARE OM3 OL3 OC3M3 Figure 15-26. Channel 3 Output Compare/Pulse Accumulator Logic Technical Data 324 MMC2107 - Rev. 2.0 Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) Functional Description 15.8.5 General-Purpose I/O Ports An I/O pin used by the timer defaults to general-purpose I/O unless an internal function which uses that pin is enabled. The timer pins can be configured for either an input capture function or an output compare function. The IOSx bits in the timer IC/OC select register configure the timer port pins as either input capture or output compare pins. Freescale Semiconductor, Inc... The timer port data direction register controls the data direction of an input capture pin. External pin conditions trigger input captures on input capture pins configured as inputs. To configure a pin for input capture: 1. Clear the pin's IOS bit in TIMIOS. 2. Clear the pin's DDR bit in TIMDDR. 3. Write to TIMCTL2 to select the input edge to detect. TIMDDR does not affect the data direction of an output compare pin. The output compare function overrides the data direction register but does not affect the state of the data direction register. To configure a pin for output compare: 1. Set the pin's IOS bit in TIMIOS. 2. Write the output compare value to TIMCxH/L. 3. Clear the pin's DDR bit in TIMDDR. 4. Write to the OMx/OLx bits in TIMCTL1 to select the output action. Table 15-7. TIMPORT I/O Function In Out Data Direction Register Output Compare Action Reading at Data Bus Reading at Pin 0 0 Pin Pin 0 1 Pin Output compare action 1 1 Port data register Output compare action 1 0 Port data register Port data register MMC2107 - Rev. 2.0 MOTOROLA Technical Data Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com 325 Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) 15.9 Reset Reset initializes the timer registers to a known startup state as described in the 15.7 Memory Map and Registers. 15.10 Interrupts Freescale Semiconductor, Inc... Table 15-8 lists the interrupt requests generated by the timer. Table 15-8. Timer Interrupt Requests Interrupt Request Flag Enable Bit Channel 3 IC/OC C3F C3I Channel 2 IC/OC C2F C2I Channel 1 IC/OC C1F C1I Channel 0 IC/OC C0F C0I PAOVF PAOVI PA input PAIF PAI Timer overflow TOF TOI PA overflow 15.10.1 Timer Channel Interrupts (CxF) A channel flag is set when an input capture or output compare event occurs. Clear a channel flag by writing a 1 to it. NOTE: When the fast flag clear all bit, TFFCA, is set, an input capture read or an output compare write clears the corresponding channel flag. TFFCA is in timer system control register 1 (TIMSCR1). When a channel flag is set, it does not inhibit subsequent output compares or input captures Technical Data 326 MMC2107 - Rev. 2.0 Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Timer Modules (TIM1 and TIM2) Interrupts 15.10.2 Pulse Accumulator Overflow (PAOVF) PAOVF is set when the 16-bit pulse accumulator rolls over from $FFFF to $0000. If the PAOVI bit in TIMPACTL is also set, PAOVF generates an interrupt request. Clear PAOVF by writing a 1 to it. NOTE: When the fast flag clear all enable bit, TFFCA, is set, any access to the pulse accumulator counter registers clears all the flags in TIMPAFLG. Freescale Semiconductor, Inc... 15.10.3 Pulse Accumulator Input (PAIF) PAIF is set when the selected edge is detected at the PAI pin. In event counter mode, the event edge sets PAIF. In gated time accumulation mode, the trailing edge of the gate signal at the PAI pin sets PAIF. If the PAI bit in TIMPACTL is also set, PAIF generates an interrupt request. Clear PAIF by writing a 1 to it. NOTE: When the fast flag clear all enable bit, TFFCA, is set, any access to the pulse accumulator counter registers clears all the flags in TIMPAFLG. 15.10.4 Timer Overflow (TOF) TOF is set when the timer counter rolls over from $FFFF to $0000. If the TOI bit in TIMSCR2 is also set, TOF generates an interrupt request. Clear TOF by writing a 1 to it. NOTE: When the timer channel 3 registers contain $FFFF and TCRE is set, TOF never gets set even though the timer counter registers go from $FFFF to $0000. When the fast flag clear all bit, TFFCA, is set, any access to the timer counter registers clears timer flag register 2. The TFFCA bit is in timer system control register 1 (TIMSCR1). When TOF is set, it does not inhibit future overflow events. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com 327 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Timer Modules (TIM1 and TIM2) Technical Data 328 MMC2107 - Rev. 2.0 Timer Modules (TIM1 and TIM2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 16. Serial Communications Interface Modules (SCI1 and SCI2) Freescale Semiconductor, Inc... 16.1 Contents 16.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330 16.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331 16.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332 16.5 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .333 16.5.1 Doze Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .333 16.5.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .333 16.6 Signal Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334 16.6.1 RXD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334 16.6.2 TXD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334 16.7 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 334 16.7.1 SCI Baud Rate Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 336 16.7.2 SCI Control Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . .337 16.7.3 SCI Control Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . .340 16.7.4 SCI Status Register 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342 16.7.5 SCI Status Register 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344 16.7.6 SCI Data Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345 16.7.7 SCI Pullup and Reduced Drive Register . . . . . . . . . . . . . . 346 16.7.8 SCI Port Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . .347 16.7.9 SCI Data Direction Register . . . . . . . . . . . . . . . . . . . . . . . . 348 16.8 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349 16.9 Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349 16.10 Baud Rate Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 16.11 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351 16.11.1 Frame Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352 16.11.2 Transmitting a Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353 16.11.3 Break Frames. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355 16.11.4 Idle Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com 329 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Serial Communications Interface Modules (SCI1 and SCI2) 16.12 Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356 16.12.1 Frame Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356 16.12.2 Receiving a Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356 16.12.3 Data Sampling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357 16.12.4 Framing Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362 16.12.5 Baud Rate Tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362 16.12.5.1 Slow Data Tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . 363 16.12.5.2 Fast Data Tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . 364 16.12.6 Receiver Wakeup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365 16.12.6.1 Idle Input Line Wakeup (WAKE = 0) . . . . . . . . . . . . . . . 365 16.12.6.2 Address Mark Wakeup (WAKE = 1). . . . . . . . . . . . . . . . 365 16.13 Single-Wire Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366 16.14 Loop Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367 16.15 I/O Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368 16.16 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369 16.17 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369 16.17.1 Transmit Data Register Empty . . . . . . . . . . . . . . . . . . . . . . 369 16.17.2 Transmission Complete . . . . . . . . . . . . . . . . . . . . . . . . . . . 369 16.17.3 Receive Data Register Full. . . . . . . . . . . . . . . . . . . . . . . . . 370 16.17.4 Idle Receiver Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370 16.17.5 Overrun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370 16.2 Introduction The serial communications interface (SCI) allows asynchronous serial communications with peripheral devices and other microcontroller units (MCU). The MMC2107 has two identical SCI modules, each with its own control registers and input/output (I/O) pins. In the text that follows, SCI register names are denoted generically. Thus, SCIPORT refers interchangeably to SCI1PORT and SCI2PORT, the port data registers for SCI1 and SCI2, respectively. Technical Data 330 MMC2107 - Rev. 2.0 Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) Features 16.3 Features Freescale Semiconductor, Inc... Features of each SCI module include: * Full-duplex operation * Standard mark/space non-return-to-zero (NRZ) format * 13-bit baud rate selection * Programmable 8-bit or 9-bit data format * Separately enabled transmitter and receiver * Separate receiver and transmitter central processor unit (CPU) interrupt requests * Programmable transmitter output polarity * Two receiver wakeup methods: - Idle line wakeup - Address mark wakeup * Interrupt-driven operation with eight flags: - - - - - - - - Transmitter empty Transmission complete Receiver full Idle receiver input Receiver overrun Noise error Framing error Parity error * Receiver framing error detection * Hardware parity checking * 1/16 bit-time noise detection * General-purpose, I/O capability MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com 331 Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) 16.4 Block Diagram IPBUS SCI DATA REGISTER RAF R8 FE IDLE PF RDRF NF OR RECEIVE SHIFT REGISTER RXD PIN Freescale Semiconductor, Inc... SCBR[12:0] RE SYSTEM CLOCK RECEIVE AND WAKEUP CONTROL BAUD RATE GENERATOR ILIE IDLE INTERRUPT REQUEST RDRF/OR INTERRUPT REQUEST RIE RWU LOOPS RSRC /16 M WAKE DATA FORMAT CONTROL ILT PE PT TE TRANSMIT CONTROL LOOPS SBK RSRC TIE TDRE TXD PIN TRANSMIT SHIFT REGISTER TC T8 TCIE TDRE INTERRUPT REQUEST TC INTERRUPT REQUEST SCI DATA REGISTER IPBUS Figure 16-1. SCI Block Diagram Technical Data 332 MMC2107 - Rev. 2.0 Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) Modes of Operation 16.5 Modes of Operation SCI operation is identical in run, special, and emulation modes. The SCI has two low-power modes, doze and stop. NOTE: Run mode is the normal mode of operation and the WAIT instruction does not affect SCI operation. Freescale Semiconductor, Inc... 16.5.1 Doze Mode When the SCIDOZ bit in the SCI pullup and reduced drive (SCIPURD) register is set, the DOZE instruction stops the SCI clock and puts the SCI in a low-power state. The DOZE instruction does not affect SCI register states. Any transmission or reception in progress stops at doze mode entry and resumes when an internal or external interrupt request brings the CPU out of doze mode. Exiting doze mode by reset aborts any transmission or reception in progress and resets the SCI. When the SCIDOZ bit is clear, execution of the DOZE instruction has no effect on the SCI. Normal module operation continues, allowing any SCI interrupt to bring the CPU out of doze mode. 16.5.2 Stop Mode The STOP instruction stops the SCI clock and puts the SCI in a low-power state. The STOP instruction does not affect SCI register states. Any transmission or reception in progress halts at stop mode entry and resumes when an external interrupt request brings the CPU out of stop mode. Exiting stop mode by reset aborts any transmission or reception in progress and resets the SCI. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com 333 Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) 16.6 Signal Description Table 16-1 gives an overview of the signals which are described here. Freescale Semiconductor, Inc... Table 16-1. Signal Properties Name Function Port Reset State Pullup RXD Receive data pin SCIPORT0 0 Disabled TXD Transmit data pin SCIPORT1 0 Disabled 16.6.1 RXD RXD is the SCI receiver pin. RXD is available for general-purpose I/O when it is not configured for receiver operation. 16.6.2 TXD TXD is the SCI transmitter pin. TXD is available for general-purpose I/O when it is not configured for transmitter operation. 16.7 Memory Map and Registers Table 16-1 shows the SCI memory map. NOTE: Reading unimplemented addresses (0x00cc_000b through 0x00cc_000f) returns 0s. Writing to unimplemented addresses has no effect. Accessing unimplemented addresses does not generate an error response. Technical Data 334 MMC2107 - Rev. 2.0 Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) Memory Map and Registers Table 16-2. Serial Communications Interface Module Memory Map(1) Freescale Semiconductor, Inc... Address Bits 7-0 Access(2) 0x00cd_0000 SCI baud register high (SCIBDH) S/U 0x00cc_0001 0x00cd_0001 SCI baud register low (SCIBDL) S/U 0x00cc_0002 0x00cd_0002 SCI control register1 (SCICR1) S/U 0x00cc_0003 0x00cd_0003 SCI control register 2 (SCICR2) S/U 0x00cc_0004 0x00cd_0004 SCI status register 1 (SCISR1) S/U 0x00cc_0005 0x00cd_0005 SCI status register 2 (SCISR2) S/U 0x00cc_0006 0x00cd_0006 SCI data register high (SCIDRH) S/U 0x00cc_0007 0x00cd_0007 SCI data register low (SCIDRL) S/U 0x00cc_0008 0x00cd_0008 SCI pullup and reduced drive register (SCIPURD) S/U 0x00cc_0009 0x00cd_0009 SCI port data register (SCIPORT) S/U 0x00cc_000a 0x00cd_000a SCI data direction register (SCIDDR) S/U 0x00cc_000b to 0x00cc_000f 0x00cd_000b to 0x00cd_000f Reserved(3) S/U SCI1 SCI2 0x00cc_0000 1. Each module is assigned 64 Kbytes of address space, all of which may not be decoded. Accesses outside of the specified module memory map generate a bus error exception. 2. S/U = CPU supervisor or user mode access. User mode accesses to supervisor only addresses have no effect and result in a cycle termination transfer error. 3. Within the specified module memory map, accessing reserved addresses does not generate a bus error exception. Reads of reserved addresses return 0s and writes have no effect. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com 335 Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) 16.7.1 SCI Baud Rate Registers Address: SCI1 -- 0x00cc_0000 SCI2 -- 0x00cd_0000 Read: Bit 7 6 5 0 0 0 0 0 0 4 3 2 1 Bit 0 SBR12 SBR11 SBR10 SBR9 SBR8 0 0 0 0 0 Write: Reset: Freescale Semiconductor, Inc... = Writes have no effect and the access terminates without a transfer error exception. Figure 16-2. SCI Baud Rate Register High (SCIBDH) Address: SCI1 -- 0x00cc_0001 SCI2 -- 0x00cd_0001 Read: Bit 7 6 5 4 3 2 1 Bit 0 SBR7 SBR6 SBR5 SBR4 SBR3 SBR2 SBR1 SBR0 0 0 0 0 0 1 0 0 Write: Reset: Figure 16-3. SCI Baud Rate Register Low (SCIBDL) Read: Anytime Write: Anytime SBR[12:8], SBR[7:0] -- SCI Baud Rate Bits These read/write bits control the SCI baud rate: SCI baud rate = fsys 16 x SBR[12:0] where: 1 SBR[12:0] 8191 NOTE: The baud rate generator is disabled until the TE bit or the RE bit in SCICR2 is set for the first time after reset. The baud rate generator is disabled when SBR[12:0] = 0. Writing to SCIBDH has no effect without also writing to SCIBDL. Writing to SCIBDH puts the data in a temporary location until data is written to SCIBDL. Technical Data 336 MMC2107 - Rev. 2.0 Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) Memory Map and Registers 16.7.2 SCI Control Register 1 Address: SCI1 -- 0x00cc_0002 SCI2 -- 0x00cd_0002 Read: Bit 7 6 5 4 3 2 1 Bit 0 LOOPS WOMS RSRC M WAKE ILT PE PT 0 0 0 0 0 0 0 0 Write: Reset: Freescale Semiconductor, Inc... Figure 16-4. SCI Control Register 1 (SCICR1) Read: Anytime Write: Anytime LOOPS -- Loop Select Bit This read/write control bit switches the SCI between normal mode and loop mode. Reset clears LOOPS. 1 = Loop mode SCI operation 0 = Normal mode SCI operation The SCI operates normally (LOOPS = 0, RSRC = X) when the output of its transmitter is connected to the TXD pin, and the input of its receiver is connected to the RXD pin. In loop mode (LOOPS =1, RSRC = 0), the input to the SCI receiver is internally disconnected from the RXD pin logic and instead connected to the output of the SCI transmitter. The behavior of TXD is governed by the DDRSC1 bit in SCIDDR. If DDRSC1 = 1, the TXD pin is driven with the output of the SCI transmitter. If DDRSC1 = 0, the TXD pin idles high. See 16.14 Loop Operation for additional information. For either loop mode or single-wire mode to function, both the SCI receiver and transmitter must be enabled by setting the RE and TE bits in SCIxCR2. NOTE: The RXD pin becomes general-purpose I/O when LOOPS = 1, regardless of the state of the RSRC bit. DDRSC0 in SCIDDR is the data direction bit for the RXD pin. Table 16-3 shows how the LOOPS, RSRC, and DDRSC0 bits affect SCI operation and the configuration of the RXD and TXD pins. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com 337 Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) RSRC SCI Mode 0 X Normal Freescale Semiconductor, Inc... 0 Loop Receiver Input Tied to RXD input buffer RXD Pin Function Receive pin 1 Transmitter Output TXD Pin Function X Tied to TXD output driver Transmit pin 0 Tied to receiver input only None (idles high) Tied to transmitter output Generalpurpose I/O 1 DDRSC0 LOOPS Table 16-3. SCI Normal, Loop, and Single-Wire Mode Pin Configurations 1 Tied to receiver input and TXD output driver Transmit pin 0 No connection Receive pin 1 Tied to TXD output driver Transmit pin Single-wire Tied to TXD WOMS -- Wired-OR Mode Select Bit This read/write bit configures the TXD and RXD pins for open-drain operation. This allows all of the TXD pins to be tied together in a multiple-transmitter system. WOMS also affects the TXD and RXD pins when they are general-purpose outputs. External pullup resistors are necessary on open-drain outputs. Reset clears WOMS. 1 = TXD and RXD pins open-drain when outputs 0 = TXD and RXD pins CMOS drive when outputs RSRC -- Receiver Source Bit This read/write bit selects the internal feedback path to the receiver input when LOOPS = 1. Reset clears RSRC. 1 = Receiver input tied to TXD pin when LOOPS = 1 0 = Receiver input tied to transmitter output when LOOPS = 1 M -- Data Format Mode Bit This read/write bit selects 11-bit or 10-bit frames. Reset clears M. 1 = Frames have 1 start bit, 9 data bits, and 1 stop bit. 0 = Frames have 1 start bit, 8 data bits, and 1 stop bit. Technical Data 338 MMC2107 - Rev. 2.0 Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) Memory Map and Registers WAKE -- Wakeup Bit This read/write bit selects the condition that wakes up the SCI receiver when it has been placed in a standby state by setting the RWU bit in SCICR2. When WAKE is set, a logic 1 (address mark) in the most significant bit position of a received data character wakes the receiver. An idle condition on the RXD pin does so when WAKE = 0. Reset clears WAKE. 1 = Address mark receiver wakeup 0 = Idle line receiver wakeup Freescale Semiconductor, Inc... ILT -- Idle Line Type Bit This read/write bit determines when the receiver starts counting logic 1s as idle character bits. The counting begins either after the start bit or after the stop bit. If the count begins after the start bit, then a string of logic 1s preceding the stop bit may cause false recognition of an idle character. Beginning the count after the stop bit avoids false idle character recognition, but requires properly synchronized transmissions. Reset clears ILT. 1 = Idle frame bit count begins after stop bit. 0 = Idle frame bit count begins after start bit. PE -- Parity Enable Bit This read/write bit enables the parity function. When enabled, the parity function inserts a parity bit in the most significant bit position of an SCI data word. Reset clears PE. 1 = Parity function enabled 0 = Parity function disabled PT -- Parity Type Bit This read/write bit selects even parity or odd parity. With even parity, an even number of 1s clears the parity bit and an odd number of 1s sets the parity bit. With odd parity, an odd number of 1s clears the parity bit and an even number of 1s sets the parity bit. Reset clears PT. 1 = Odd parity when PE = 1 0 = Even parity when PE = 1 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com 339 Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) 16.7.3 SCI Control Register 2 Address: SCI1 -- 0x00cc_0003 SCI2 -- 0x00cd_0003 Bit 7 6 5 4 3 2 1 Bit 0 TIE TCIE RIE ILIE TE RE RWU SBK 0 0 0 0 0 0 0 0 Read: Write: Reset: Freescale Semiconductor, Inc... Figure 16-5. SCI Control Register 2 (SCICR2) Read: Anytime Write: Anytime TIE -- Transmitter Interrupt Enable Bit This read/write bit allows the TDRE flag to generate interrupt requests. Reset clears TIE. 1 = TDRE interrupt requests enabled 0 = TDRE interrupt requests disabled TCIE -- Transmission Complete Interrupt Enable Bit This read/write bit allows the TC flag to generate interrupt requests. Reset clears TCIE. 1 = TC interrupt requests enabled 0 = TC interrupt requests disabled RIE -- Receiver Interrupt Enable Bit This read/write bit allows the RDRF and OR flags to generate interrupt requests. Reset clears RIE. 1 = RDRF and OR interrupt requests enabled 0 = RDRF and OR interrupt requests disabled ILIE -- Idle Line Interrupt Enable Bit This read/write bit allows the IDLE flag to generate interrupt requests. Reset clears ILIE. 1 = IDLE interrupt requests enabled 0 = IDLE interrupt requests disabled Technical Data 340 MMC2107 - Rev. 2.0 Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) Memory Map and Registers TE -- Transmitter Enable Bit This read/write bit enables the transmitter and configures the TXD pin as the transmitter output. Toggling TE queues an idle frame. Reset clears TE. 1 = Transmitter enabled 0 = Transmitter disabled RE -- Receiver Enable Bit Freescale Semiconductor, Inc... This read/write bit enables the receiver. Reset clears RE. 1 = Receiver enabled 0 = Receiver disabled NOTE: When LOOPS = 0 and TE = RE = 1, the RXD pin is an input and the TXD pin is an output regardless of the state of the DDRSC1 (TXD) and DDRSC0 (RXD) bits. RWU -- Receiver Wakeup Bit This read/write bit puts the receiver in a standby state that inhibits receiver interrupt requests. The WAKE bit determines whether an idle input or an address mark wakes up the receiver and clears RWU. Reset clears RWU. 1 = Receiver asleep when RE = 1 0 = Receiver awake when RE = 1 SBK -- Send Break Bit Setting this read/write bit causes the SCI to send break frames of 10 (M = 0) or 11 (M =1) logic 0s. To send one break frame, set SBK and then clear it before the break frame is finished transmitting. As long as SBK is set, the transmitter continues to send break frames. 1 = Transmitter sends break frames. 0 = Transmitter does not send break frames. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com 341 Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) 16.7.4 SCI Status Register 1 Address: SCI1 -- 0x00cc_0004 SCI2 -- 0x00cd_0004 Read: Bit 7 6 5 4 3 2 1 Bit 0 TDRE TC RDRF IDLE OR NF FE PF 1 1 0 0 0 0 0 0 Write: Freescale Semiconductor, Inc... Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 16-6. SCI Status Register 1 (SCISR1) Read: Anytime Write: Has no meaning or effect TDRE -- Transmit Data Register Empty Flag The TDRE flag is set when the transmit shift register receives a word from the SCI data register. It signals that the SCIDRH and SCIDRL are empty and can receive new data to transmit. If the TIE bit in the SCICR2 is also set, TDRE generates an interrupt request. Clear TDRE by reading SCISR1 and then writing to SCIDRL. Reset sets TDRE. 1 = Transmit data register empty 0 = Transmit data register not empty TC -- Transmit Complete Flag The TC flag is set when TDRE = 1 and no data, preamble, or break frame is being transmitted. It signals that no transmission is in progress. If the TCIE bit is set in SCICR2, TC generates an interrupt request. When TC is set, the TXD pin is idle (logic 1). TC is cleared automatically when a data, preamble, or break frame is queued. Clear TC by reading SCISR1 with TC set and then writing to SCIDRL. TC cannot be cleared while a transmission is in progress. Reset sets TC. 1 = No transmission in progress 0 = Transmission in progress Technical Data 342 MMC2107 - Rev. 2.0 Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) Memory Map and Registers RDRF -- Receive Data Register Full Flag The RDRF flag is set when the data in the receive shift register is transferred to SCIDRH and SCIDRL. It signals that the received data is available to the MCU. If the RIE bit is set in SCICR2, RDRF generates an interrupt request. Clear RDRF by reading the SCISR1 and then reading SCIDRL. Reset clears RDRF. 1 = Received data available in SCIDRH and SCIDRL 0 = Received data not available in SCIDRH and SCIDRL IDLE -- Idle Line Flag Freescale Semiconductor, Inc... The IDLE flag is set when 10 (if M = 0) or 11 (if M = 1) consecutive logic 1s appear on the receiver input. If the ILIE bit in SCICR2 is set, IDLE generates an interrupt request. Once IDLE is cleared, a valid frame must again set the RDRF flag before an idle condition can set the IDLE flag. Clear IDLE by reading SCISR1 and then reading SCIDRL. Reset clears IDLE. 1 = Receiver idle 0 = Receiver active or idle since reset or idle since IDLE flag last cleared NOTE: When RWU =1, an idle line condition does not set the IDLE flag. OR -- Overrun Flag The OR flag is set if data is not read from SCIDRL before the receive shift register receives the stop bit of the next frame. This is a receiver overrun condition. If the RIE bit in SCICR2 is set, OR generates an interrupt request. The data in the shift register is lost, but the data already in the SCIDRH and SCIDRL is not affected. Clear OR by reading SCISR1 and then reading SCIDRL. Reset clears OR. 1 = Overrun 0 = No overrun NF -- Noise Flag The NF flag is set when the SCI detects noise on the receiver input. NF is set during the same cycle as the RDRF flag but does not get set in the case of an overrun. Clear NF by reading SCISR1 and then reading SCIDRL. Reset clears NF. 1 = Noise 0 = No noise MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com 343 Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) FE -- Framing Error Flag The FE flag is set when a logic 0 is accepted as the stop bit. FE is set during the same cycle as the RDRF flag but does not get set in the case of an overrun. FE inhibits further data reception until it is cleared. Clear FE by reading SCISR1 and then reading SCIDRL. Reset clears FE. 1 = Framing error 0 = No framing error Freescale Semiconductor, Inc... PF -- Parity Error Flag The PF flag is set when PE = 1 and the parity of the received data does not match its parity bit. Clear PF by reading SCISR1 and then reading SCIDRL. Reset clears PF. 1 = Parity error 0 = No parity error 16.7.5 SCI Status Register 2 Address: SCI1 -- 0x00cc_0005 SCI2 -- 0x00cd_0005 Read: Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 RAF 0 0 0 0 0 0 0 0 Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 16-7. SCI Status Register 2 (SCISR2) Read: Anytime Write: Has no meaning or effect RAF -- Receiver Active Flag The RAF flag is set when the receiver detects a logic 0 during the RT1 time period of the start bit search. When the receiver detects an idle character, it clears RAF. Reset clears RAF. 1 = Reception in progress 0 = No reception in progress Technical Data 344 MMC2107 - Rev. 2.0 Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) Memory Map and Registers 16.7.6 SCI Data Registers Address: SCI1 -- 0x00cc_0006 SCI2 -- 0x00cd_0006 Bit 7 Read: 6 R8 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 T8 Write: Reset: 0 0 Freescale Semiconductor, Inc... = Writes have no effect and the access terminates without a transfer error exception. Figure 16-8. SCI Data Register High (SCIDRH) Address: SCI1 -- 0x00cc_0007 SCI2 -- 0x00cd_0007 Bit 7 6 5 4 3 2 1 Bit 0 Read: R7 R6 R5 R4 R3 R2 R1 R0 Write: T7 T6 T5 T4 T3 T2 T1 T0 Reset: 0 0 0 0 0 0 0 0 Figure 16-9. SCI Data Register Low (SCIDRL) Read: Anytime Write: Anytime; writing to R8 has no effect R8 -- Receive Bit 8 The R8 bit is the ninth received data bit when using the 9-bit data format (M = 1). Reset clears R8. T8 -- Transmit Bit 8 The T8 bit is the ninth transmitted data bit when using the 9-bit data format (M = 1). Reset clears T8. R[7:0] -- Receive Bits [7:0] The R[7:0] bits are receive bits [7:0] when using the 9-bit or 8-bit data format. Reset clears R[7:0]. T[7:0] -- Transmit Bits [7:0] The T[7:0] bits are transmit bits [7:0] when using the 9-bit or 8-bit data format. Reset clears T[7:0]. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com 345 Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) NOTE: If the value of T8 is the same as in the previous transmission, T8 does not have to be rewritten. The same value is transmitted until T8 is rewritten. When using the 8-bit data format, only SCIDRL needs to be accessed. When using 8-bit write instructions to transmit 9-bit data, write first to SCIDRH, then to SCIDRL. Freescale Semiconductor, Inc... 16.7.7 SCI Pullup and Reduced Drive Register Address: SCI1 -- 0x00cc_0008 SCI2 -- 0x00cd_0008 Bit 7 6 Read: 5 4 RSVD5 RDPSCI 0 0 0 SCISDOZ 3 2 0 0 1 Bit 0 RSVD1 PUPSCI 0 0 Write: Reset: 0 0 0 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 16-10. SCI Pullup and Reduced Drive Register (SCIPURD) Write: Anytime SCISDOZ -- SCI Stop in Doze Mode Bit The SCISDOZ bit disables the SCI in doze mode. 1 = SCI disabled in doze mode 0 = SCI enabled in doze mode RSVD[5:1] -- Reserved Writing to these read/write bits updates their values but has no effect on functionality. RDPSCI -- Reduced Drive Bit This read/write bit controls the drive capability of TXD and RXD. 1 = Reduced TXD and RXD pin drive 0 = Full TXD and RXD pin drive Technical Data 346 MMC2107 - Rev. 2.0 Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) Memory Map and Registers PUPSCI -- Pullup Enable Bit This read/write bit enables the pullups on pins TXD and RXD. If a pin is programmed as an output, the pullup is disabled. 1 = TXD and RXD pullups enabled 0 = TXD and RXD pullups disabled 16.7.8 SCI Port Data Register Freescale Semiconductor, Inc... Address: SCI1 -- 0x00cc_0009 SCI2 -- 0x00cd_0009 Bit 7 6 5 4 3 2 RSVD7 RSVD6 RSVD5 RSVD4 RSVD3 RSVD2 0 0 0 0 0 0 1 Bit 0 Read: PORTSC1 PORTSC0 Write: Reset: Pin function: 0 0 TXD RXD Figure 16-11. SCI Port Data Register (SCIPORT) Read: Anytime; when DDRSCx = 0, its pin is configured as an input, and reading PORTSCx returns the pin level; when DDRSCx = 1, its pin is configured as an output, and reading PORTSCx returns the pin driver input level. Write: Anytime; data stored in internal latch drives pin only if DDRSC bit = 1 RSVD[7:2] -- Reserved Writing to these read/write bits updates their values but has no effect on functionality. PORTSC[1:0] -- SCIPORT Data Bits These are the read/write data bits of the SCI port. NOTE: Writes to SCIPORT do not change the pin state when the pin is configured for SCI input. To ensure correct reading of the SCI pin values from SCIPORT, always wait at least one cycle after writing to SCIDDR before reading SCIPORT. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com 347 Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) 16.7.9 SCI Data Direction Register Address: SCI1 -- 0x00cc_000a SCI2 -- 0x00cd_000a Bit 7 6 5 4 3 2 RSVD7 RSVD6 RSVD5 RSVD4 RSVD3 RSVD2 0 0 0 0 0 0 1 Bit 0 Read: DDRSC1 DDRSC0 Write: Reset: 0 0 Freescale Semiconductor, Inc... Figure 16-12. SCI Data Direction Register (SCIDDR) Read: Anytime Write: Anytime RSVD[7:2] -- Reserved Writing to these read/write bits updates their values but has no effect on functionality. DDRSC[1:0] -- SCIPORT Data Direction Bits These bits control the data direction of the SCIPORT pins. Reset clears DDRSC[1:0]. 1 = Corresponding pin configured as output 0 = Corresponding pin configured as input NOTE: When LOOPS = 0 and TE = RE = 1, the RXD pin is an input and the TXD pin is an output regardless of the state of the DDRSC1 (TXD) and DDRSC0 (RXD) bits. Technical Data 348 MMC2107 - Rev. 2.0 Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) Functional Description 16.8 Functional Description Freescale Semiconductor, Inc... The SCI allows full-duplex, asynchronous, non-return-to-zero (NRZ) serial communication between the MCU and remote devices, including other MCUs. The SCI transmitter and receiver operate independently, although they use the same baud rate generator. The CPU monitors the status of the SCI, writes the data to be transmitted, and processes received data. 16.9 Data Format The SCI uses the standard NRZ mark/space data format shown in Figure 16-13. Each frame has a start bit, eight or nine data bits, and one or two stop bits. Clearing the M bit in SCCR1 configures the SCI for 10-bit frames. Setting the M bit configures the SCI for 11-bit frames. When the SCI is configured for 9-bit data, the ninth data bit is the T8 bit in SCI data register high (SCIDRH). It remains unchanged after transmission and can be used repeatedly without rewriting it. A frame with nine data bits has a total of 11 bits. 10-BIT FRAME M = 1 in SCICR1 START BIT BIT 0 BIT 1 BIT 2 BIT 3 BIT 4 BIT 5 BIT 6 BIT 7 STOP BIT NEXT START BIT 11-BIT FRAME M = 1 IN SCICR1 START BIT BIT 0 BIT 1 BIT 2 BIT 3 BIT 4 BIT 5 BIT 6 BIT 7 BIT 8 STOP BIT NEXT START BIT Figure 16-13. SCI Data Formats MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com 349 Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) 16.10 Baud Rate Generation A 13-bit modulus counter in the baud rate generator derives the baud rate for both the receiver and the transmitter. The value from 0 to 8191 written to SCIBDH and SCIBDL determines the system clock divisor. The baud rate clock is synchronized with the bus clock and drives the receiver. The baud rate clock divided by 16 drives the transmitter. The receiver acquisition rate is 16 samples per bit time. Freescale Semiconductor, Inc... Baud rate generation is subject to two sources of error: 1. Integer division of the module clock may not give the exact target frequency. 2. Synchronization with the bus clock can cause phase shift. Table 16-4. Example Baud Rates (System Clock = 33 MHz) SBR[12:0] Receiver Clock (Hz) Transmitter Clock (Hz) Target Baud Rate Percent Error 0x0012 1,833,333.3 114,583.3 115,200 0.54 0x0024 916,666.7 57,291.7 57,600 0.54 0x0036 611,111.1 38,194.4 38,400 0.54 0x003d 540,983.6 33,811.4 33,600 0.63 0x0048 458,333.3 28,645.8 28,800 0.54 0x006b 308,411.2 19,275.7 19,200 0.39 0x0008f 230,769.2 14,423.1 14,400 0.16 0x00d7 153,488.4 95,93.0 9,600 0.07 0x01ae 76,744.2 4,796.5 4,800 0.07 0x035b 38,416.8 2,401.0 2,400 0.04 0x06b7 19,197.2 1,199.8 1,200 0.01 0x0d6d 9,601.4 600.1 600 0.01 0x1adb 4,800.0 300.0 300 0 Technical Data 350 MMC2107 - Rev. 2.0 Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) Transmitter 16.11 Transmitter IPBUS SYSTEM CLOCK BAUD DIVIDER / 16 LOOPS SCI DATA REGISTER LOOP CONTROL Freescale Semiconductor, Inc... H 11-BIT TRANSMIT SHIFT REGISTER 8 7 6 5 4 3 2 1 0 L PIN BUFFER AND CONTROL MSB M START STOP SBR[12:0] FORCE PIN DIRECTION BREAK (ALL 0s) PREAMBLE (ALL 1s) PARITY GENERATION SHIFT ENABLE PT TXD PIN WOMS LOAD FROM SCIDR PE TO RECEIVER TRANSMITTER CONTROL TDRE INTERRUPT REQUEST TC INTERRUPT REQUEST TDRE TE SBK TIE TC TCIE Figure 16-14. Transmitter Block Diagram MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com 351 Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) 16.11.1 Frame Length The transmitter can generate either 10-bit or 11-bit frames. In SCICR1, the M bit selects frame length, and the PE bit enables the parity function. One data bit may be an address mark or an extra stop bit. All frames begin with a start bit and end with one or two stop bits. When transmitting 9-bit data, bit T8 in SCI data register high (SCIDRH) is the ninth bit (bit 8). Freescale Semiconductor, Inc... Table 16-5. Example 10-Bit and 11-Bit Frames M Bit 0 1 Frame Length Start Bit Data Bits Parity Bit Address Mark(1) Stop Bit(s) 1 8 No No 1 1 7 No No 2 1 7 No Yes 1 1 7 Yes No 1 1 9 No No 1 1 8 No No 2 1 8 No Yes 1 1 8 Yes No 1 1 7 No Yes 2 1 7 Yes No 2 10 bits 11 bits 1. When implementing a multidrop network using the SCI, the address mark bit is used to designate subsequent data frames as a network address and not device data. Technical Data 352 MMC2107 - Rev. 2.0 Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) Transmitter 16.11.2 Transmitting a Frame To begin an SCI transmission: 1. Configure the SCI: a. Write a baud rate value to SCIBDH and SCIBDL. b. Write to SCICR1 to: i. Enable or disable loop mode and select the receiver feedback path Freescale Semiconductor, Inc... ii. Select open-drain or wired-OR SCI outputs iii. Select 10-bit or 11-bit frames iv. Select the receiver wakeup condition: address mark or idle line v. Select idle line type vi. Enable or disable the parity function and select odd or even parity c. Write to SCICR2 to: i. Enable or disable TDRE, TC, RDRF, and IDLE interrupt requests ii. Enable the transmitter and queue a break frame iii. Enable or disable the receiver iv. Put the receiver in standby if required 2. Transmit a byte: a. Clear the TDRE flag by reading SCISR1 and, if sending 9-bit data, write the ninth data bit to SCDRH. b. Write the byte to be transmitted (or low-order 8 bits if sending 9-bit data) to SCIDRL. 3. Repeat step 2 for each subsequent transmission. Writing the TE bit from 0 to 1 loads the transmit shift register with a preamble of 10 (if M = 0) or 11 (if M = 1) logic 1s. When the preamble shifts out, the SCI transfers the data from SCIDRH and SCIDRL to the transmit shift register. The transmit shift register prefaces the data with a 0 start bit and appends the data with a 1 stop bit and begins shifting out the frame. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com 353 Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) The SCI sets the TDRE flag every time it transfers data from SCIDRH and SCIDRL to the transmit shift register. TDRE indicates that SCIDRH and SCIDRL can accept new data. If the TIE bit is set, TDRE generates an interrupt request. NOTE: SCIDRH and SCIDRL transfer data to the transmit shift register and sets TDRE 9/16ths of a bit time after the previous frame's stop bit starts to shift out. Freescale Semiconductor, Inc... Hardware supports odd or even parity. When parity is enabled, the most significant data bit is the parity bit. When the transmit shift register is not transmitting a frame, the TXD pin goes to the idle condition, logic 1. Clearing the TE bit while the transmitter is idle will return control of the TXD pin to the SCI data direction (SCIDDR) and SCI port (SCIPORT) registers. If the TE bit is cleared while a transmission is in progress (while TC = 0), the frame in the transmit shift register continues to shift out. Then the TXD pin reverts to being a general-purpose I/O pin even if there is data pending in the SCI data register. To avoid accidentally cutting off a message, always wait until TDRE is set after the last frame before clearing TE. To separate messages with preambles with minimum idle line time, use this sequence between messages: 1. Write the last byte of the first message to SCIDRH and SCIDRL. 2. Wait until the TDRE flag is set, indicating the transfer of the last frame to the transmit shift register. 3. Queue a preamble by clearing and then setting the TE bit. 4. Write the first byte of the second message to SCIDRH and SCIDRL. When the SCI relinquishes the TXD pin, the SCIPORT and SCIDDR registers control the TXD pin. To force TXD high when turning off the transmitter, set bit 1 of the SCI port register (SCIPORT) and bit 1 of the SCI data direction register (SCIDDR). The TXD pin goes high as soon as the SCI relinquishes control of it. Technical Data 354 MMC2107 - Rev. 2.0 Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) Transmitter 16.11.3 Break Frames Freescale Semiconductor, Inc... Setting the SBK bit in SCICR2 loads the transmit shift register with a break frame. A break frame contains all logic 0s and has no start, stop, or parity bit. Break frame length depends on the M bit in the SCICR1 register. As long as SBK is set, the SCI continuously loads break frames into the transmit shift register. After SBK is clear, the transmit shift register finishes transmitting the last break frame and then transmits at least one logic 1. The automatic logic 1 at the end of a break frame guarantees the recognition of the next start bit. The SCI recognizes a break frame when a start bit is followed by eight or nine 0 data bits and a 0 where the stop bit should be. Receiving a break frame has these effects on SCI registers: * Sets the FE flag * Sets the RDRF flag * Clears the SCIDRH and SCIDRL * May set the OR flag, NF flag, PE flag, or the RAF flag 16.11.4 Idle Frames An idle frame contains all logic 1s and has no start, stop, or parity bit. Idle frame length depends on the M bit in the SCICR1 register. The preamble is a synchronizing idle frame that begins the first transmission after writing the TE bit from 0 to 1. If the TE bit is cleared during a transmission, the TXD pin becomes idle after completion of the transmission in progress. Clearing and then setting the TE bit during a transmission queues an idle frame to be sent after the frame currently being transmitted. NOTE: When queueing an idle frame, return the TE bit to logic 1 before the stop bit of the current frame shifts out to the TXD pin. Setting TE after the stop bit appears on TXD causes data previously written to SCIDRH and SCIDRL to be lost toggle TE for a queued idle frame while the TDRE flag is set and immediately before writing new data to SCIDRH and SCIDRL. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com 355 Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) 16.12 Receiver IPBUS STOP BAUD DIVIDER DATA RECOVERY FROM TXD OR TRANSMITTER LOOP CONTROL RE 11-BIT RECEIVE SHIFT REGISTER 8 7 6 5 4 3 2 1 0 L MSB RXD H ALL 1S Freescale Semiconductor, Inc... SYSTEM CLOCK START SCI DATA REGISTER SBR[12:0] RAF LOOPS FE M RSRC WAKE ILT PE PT IDLE INTERRUPT REQUEST RDRF/OR INTERRUPT REQUEST NF WAKEUP LOGIC RWU PE R8 PARITY CHECKING IDLE ILIE RDRF RIE OR Figure 16-15. SCI Receiver Block Diagram 16.12.1 Frame Length The receiver can handle either 8-bit or 9-bit data. The state of the M bit in SCICR1 selects frame length. When receiving 9-bit data, bit R8 in SCIDRH is the ninth bit (bit 8). 16.12.2 Receiving a Frame When the SCI receives a frame, the receive shift register shifts the frame in from the RXD pin. Technical Data 356 MMC2107 - Rev. 2.0 Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) Receiver After an entire frame shifts into the receive shift register, the data portion of the frame transfers to SCIDRH and SCIDRL. The RDRF flag is set, indicating that the received data can be read. If the RIE bit is also set, RDRF generates an interrupt request. The receiver samples the RXD pin at the RT clock rate. The RT clock is an internal signal with a frequency 16 times the baud rate. To adjust for baud rate mismatch, the RT clock resynchronizes: * After every start bit * After the receiver detects a data bit change from logic 1 to logic 0 (after the majority of data bit samples at RT8, RT9, and RT10 returns a valid logic 1 and the majority of the next RT8, RT9, and RT10 samples returns a valid logic 0) To locate the start bit, data recovery logic does an asynchronous search for a 0 preceded by three 1s. When the falling edge of a possible start bit occurs, the RT clock begins to count to 16. LSB START BIT RXD SAMPLES 1 1 1 1 1 1 1 1 0 0 START BIT QUALIFICATION 0 0 START BIT VERIFICATION 0 0 0 DATA SAMPLING RT4 RT3 RT2 RT1 RT16 RT15 RT14 RT13 RT12 RT11 RT9 RT10 RT8 RT7 RT6 RT5 RT4 RT3 RT2 RT1 RT1 RT1 RT1 RT1 RT1 RT1 RT CLOCK COUNT RT1 RT CLOCK RT1 Freescale Semiconductor, Inc... 16.12.3 Data Sampling RESET RT CLOCK Figure 16-16. Receiver Data Sampling MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com 357 Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) To verify the start bit and to detect noise, data recovery logic takes samples at RT3, RT5, and RT7. Freescale Semiconductor, Inc... Table 16-6. Start Bit Verification RT3, RT5, and RT7 Samples Start Bit Verification Noise Flag 000 Yes 0 001 Yes 1 010 Yes 1 011 No 0 100 Yes 1 101 No 0 110 No 0 111 No 0 If start bit verification is not successful, the RT clock is reset and a new search for a start bit begins. To determine the value of a data bit and to detect noise, recovery logic takes samples at RT8, RT9, and RT10. Table 16-7. Data Bit Recovery NOTE: RT8, RT9, and RT10 Samples Data Bit Determination Noise Flag 000 0 0 001 0 1 010 0 1 011 1 1 100 0 1 101 1 1 110 1 1 111 1 0 The RT8, RT9, and RT10 data samples do not affect start bit verification. If any or all of the RT8, RT9, and RT10 samples are logic 1s following a successful start bit verification, the NF flag is set and the receiver interprets the bit as a start bit (logic 0). Technical Data 358 MMC2107 - Rev. 2.0 Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) Receiver The RT8, RT9, and RT10 samples also verify stop bits. RT8, RT9, and RT10 Samples Framing Error Flag Noise Flag 000 1 0 001 1 1 010 1 1 011 0 1 100 1 1 101 0 1 110 0 1 111 0 0 In Figure 16-17, the verification samples RT3 and RT5 determine that the first low detected was noise and not the beginning of a start bit. The RT clock is reset and the start bit search begins again. The NF flag is not set because the noise occurred before the start bit was verified. LSB START BIT 0 0 0 0 0 0 0 RT10 1 RT9 RT1 1 RT8 RT1 1 RT7 0 RT1 1 RT1 1 RT5 1 RT1 RXD SAMPLES RT1 RT3 RT2 RT1 RT16 RT15 RT14 RT13 RT12 RT11 RT6 RT5 RT4 RT3 RT2 RT4 RT CLOCK COUNT RT3 RT CLOCK RT2 Freescale Semiconductor, Inc... Table 16-8. Stop Bit Recovery RESET RT CLOCK Figure 16-17. Start Bit Search Example 1 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com 359 Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) In Figure 16-18, noise is perceived as the beginning of a start bit although the RT3 sample is high. The RT3 sample sets the noise flag. Although the perceived bit time is misaligned, the RT8, RT9, and RT10 data samples are within the bit time, and data recovery is successful. PERCEIVED START BIT ACTUAL START BIT LSB RT1 1 0 0 0 0 RT9 RT1 0 RT8 RT1 1 RT7 1 RT1 1 RT1 1 0 RT7 RT6 RT5 RT4 RT3 RT2 RT1 RT16 RT15 RT14 RT13 RT12 RT11 RT10 RT6 RT5 RT4 RT3 RT CLOCK COUNT RT2 RT CLOCK RESET RT CLOCK Figure 16-18. Start Bit Search Example 2 In Figure 16-19 a large burst of noise is perceived as the beginning of a start bit, although the RT5 sample is high. The RT5 sample sets the noise flag. Although this is a worst-case misalignment of perceived bit time, the data samples RT8, RT9, and RT10 are within the bit time and data recovery is successful. PERCEIVED START BIT LSB ACTUAL START BIT RT1 0 1 0 0 0 0 RT9 0 RT10 1 RT8 1 RT7 1 RT1 SAMPLES RT1 RXD RT1 RT9 RT8 RT7 RT6 RT5 RT4 RT3 RT2 RT1 RT16 RT15 RT14 RT13 RT12 RT11 RT6 RT5 RT4 RT CLOCK COUNT RT3 RT CLOCK RT2 Freescale Semiconductor, Inc... 1 RT1 RXD SAMPLES RESET RT CLOCK Figure 16-19. Start Bit Search Example 3 Technical Data 360 MMC2107 - Rev. 2.0 Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) Receiver Figure 16-20 shows the effect of noise early in the start bit time. Although this noise does not affect proper synchronization with the start bit time, it does set the noise flag. LSB PERCEIVED AND ACTUAL START BIT 1 1 1 1 1 1 1 1 0 RT1 RT1 RT1 RT1 RT1 RT1 RT1 RT1 RT1 1 0 RT3 RT2 RT1 RT16 RT15 RT14 RT13 RT12 RT11 RT10 RT9 RT8 RT7 RT6 RT5 RT4 RT3 RT CLOCK COUNT RT2 RT CLOCK RESET RT CLOCK Figure 16-20. Start Bit Search Example 4 Figure 16-21 shows a burst of noise near the beginning of the start bit that resets the RT clock. The sample after the reset is low but is not preceded by three high samples that would qualify as a falling edge. Depending on the timing of the start bit search and on the data, the frame may be missed entirely or it may set the framing error flag. 0 RT1 RT1 RT1 RT1 RT1 RT1 RT1 RT1 0 1 1 0 0 0 0 0 0 0 0 RT1 1 RT1 1 RT1 1 RT1 1 RT1 1 RT1 1 RT1 1 RT1 1 RT7 1 RT1 SAMPLES LSB START BIT NO START BIT FOUND RXD RT1 RT1 RT1 RT1 RT1 RT6 RT5 RT4 RT CLOCK COUNT RT3 RT CLOCK RT2 Freescale Semiconductor, Inc... 1 RT1 RXD SAMPLES RESET RT CLOCK Figure 16-21. Start Bit Search Example 5 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com 361 Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) In Figure 16-22 a noise burst makes the majority of data samples RT8, RT9, and RT10 high. This sets the noise flag but does not reset the RT clock. In start bits only, the RT8, RT9, and RT10 data samples are ignored. LSB START BIT 1 1 1 1 1 0 RT1 RT1 RT1 RT1 RT1 RT1 RT1 RT1 0 0 0 1 0 1 RT10 1 RT9 1 RT8 1 RT7 1 RT1 RT3 RT2 RT1 RT16 RT15 RT14 RT13 RT12 RT11 RT6 RT5 RT4 RT CLOCK COUNT RT3 RT CLOCK RT2 Freescale Semiconductor, Inc... SAMPLES RT1 RXD RESET RT CLOCK Figure 16-22. Start Bit Search Example 6 16.12.4 Framing Errors If the data recovery logic does not detect a 1 where the stop bit should be in an incoming frame, it sets the FE flag in SCISR1. A break frame also sets the FE flag because a break frame has no stop bit. The FE flag is set at the same time that the RDRF flag is set. 16.12.5 Baud Rate Tolerance A transmitting device may be operating at a baud rate below or above the receiver baud rate. Accumulated bit time misalignment can cause one of the RT8, RT9, and RT10 stop bit data samples to fall outside the stop bit. A noise error occurs if the samples are not all the same value. If more than one of the samples is outside the stop bit, a framing error occurs. In most applications, the baud rate tolerance is much more than the degree of misalignment that is likely to occur. As the receiver samples an incoming frame, it resynchronizes the RT clock on any valid falling edge within the frame. Resynchronization within frames corrects misalignments between transmitter bit times and receiver bit times. Technical Data 362 MMC2107 - Rev. 2.0 Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) Receiver 16.12.5.1 Slow Data Tolerance Figure 16-23 shows how much a slow received frame can be misaligned without causing a noise error or a framing error. The slow stop bit begins at RT8 instead of RT1 but arrives in time for the stop bit data samples at RT8, RT9, and RT10. MSB STOP RT16 RT15 RT14 RT13 RT12 RT11 RT10 RT9 RT8 RT7 RT6 RT5 RT4 RT3 RT2 RT1 Freescale Semiconductor, Inc... RECEIVER RT CLOCK DATA SAMPLES Figure 16-23. Slow Data For 8-bit data, sampling of the stop bit takes the receiver: 9 bit times x 16 RT cycles + 10 RT cycles = 154 RT cycles. With the misaligned data shown in Figure 16-23, the receiver counts 154 RT cycles at the point when the count of the transmitting device is: 9 bit times x 16 RT cycles + 3 RT cycles = 147 RT cycles. The maximum percent difference between the receiver count and the transmitter count for slow 8-bit data with no errors is: 154 - 147 x 100 = 4.54% -------------------------154 For 9-bit data, sampling of the stop bit takes the receiver: 10 bit times x 16 RT cycles + 10 RT cycles = 170 RT cycles. With the misaligned data shown in Figure 16-23, the receiver counts 170 RT cycles at the point when the count of the transmitting device is: 10 bit times x 16 RT cycles + 3 RT cycles = 163 RT cycles. The maximum percent difference between the receiver count and the transmitter count for slow 9-bit data with no errors is: 170 - 163 x 100 = 4.12% -------------------------170 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com 363 Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) 16.12.5.2 Fast Data Tolerance Figure 16-24 shows how much a fast received frame can be misaligned without causing a noise error or a framing error. The fast stop bit ends at RT10 instead of RT16 but is still sampled at RT8, RT9, and RT10. STOP IDLE OR NEXT FRAME RT16 RT15 RT14 RT13 RT12 RT11 RT10 RT9 RT8 RT7 RT6 RT5 RT4 RT3 RT2 Freescale Semiconductor, Inc... RT1 RECEIVER RT CLOCK DATA SAMPLES Figure 16-24. Fast Data For 8-bit data, sampling of the stop bit takes the receiver: 9 bit times x 16 RT cycles + 10 RT cycles = 154 RT cycles. With the misaligned data shown in Figure 16-24, the receiver counts 154 RT cycles at the point when the count of the transmitting device is: 10 bit times x 16 RT cycles = 160 RT cycles. The maximum percent difference between the receiver count and the transmitter count for fast 8-bit data with no errors is: 154 - 160 x 100 = 3.90% -------------------------154 For 9-bit data, sampling of the stop bit takes the receiver: 10 bit times x 16 RT cycles + 10 RT cycles = 170 RT cycles. With the misaligned data shown in Figure 16-24, the receiver counts 170 RT cycles at the point when the count of the transmitting device is: 11 bit times x 16 RT cycles = 176 RT cycles. The maximum percent difference between the receiver count and the transmitter count for fast 9-bit data with no errors is: 170 - 176 x 100 = 3.53% -------------------------170 Technical Data 364 MMC2107 - Rev. 2.0 Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) Receiver 16.12.6 Receiver Wakeup So that the SCI can ignore transmissions intended only for other devices in multiple-receiver systems, the receiver can be put into a standby state. Setting the RWU bit in SCICR2 puts the receiver into a standby state during which receiver interrupts are disabled. Freescale Semiconductor, Inc... The transmitting device can address messages to selected receivers by including addressing information in the initial frame or frames of each message. The WAKE bit in SCICR1 determines how the SCI is brought out of the standby state to process an incoming message. The WAKE bit enables either idle line wakeup or address mark wakeup. 16.12.6.1 Idle Input Line Wakeup (WAKE = 0) When WAKE = 0, an idle condition on the RXD pin clears the RWU bit and wakes up the receiver. The initial frame or frames of every message contain addressing information. All receivers evaluate the addressing information, and receivers for which the message is addressed process the frames that follow. Any receiver for which a message is not addressed can set its RWU bit and return to the standby state. The RWU bit remains set and the receiver remains on standby until another idle frame appears on the RXD pin. Idle line wakeup requires that messages be separated by at least one idle frame and that no message contains idle frames. The idle frame that wakes up the receiver does not set the IDLE flag or the RDRF flag. The ILT bit in SCICR1 determines whether the receiver begins counting logic 1s as idle frame bits after the start bit or after the stop bit. 16.12.6.2 Address Mark Wakeup (WAKE = 1) When WAKE = 1, an address mark clears the RWU bit and wakes up the receiver. An address mark is a 1 in the most significant data bit position. The receiver interprets the data as address data. When using address mark wakeup, the MSB of all non-address data must be 0. User code must compare the address data to the receiver's address and, if the MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com 365 Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) addresses match, the receiver processes the frames that follow. If the addresses do not match, user code must put the receiver back to sleep by setting the RWU bit. The RWU bit remains set and the receiver remains on standby until another address frame appears on the RXD pin. Freescale Semiconductor, Inc... The address mark clears the RWU bit before the stop bit is received and sets the RDRF flag. Address mark wakeup allows messages to contain idle frames but requires that the most significant byte (MSB) be reserved for address data. NOTE: With the WAKE bit clear, setting the RWU bit after the RXD pin has been idle can cause the receiver to wake up immediately. 16.13 Single-Wire Operation Normally, the SCI uses the TXD pin for transmitting and the RXD pin for receiving (LOOPS = 0, RSRC = X). In single-wire mode, the RXD pin is disconnected from the SCI and is available as a general-purpose I/O pin. The SCI uses the TXD pin for both receiving and transmitting. In single-wire mode (LOOPS = 1, RXRC = 1), setting the data direction bit for the TXD pin configures TXD as the output for transmitted data. Clearing the data direction bit configures TXD as the input for received data. TRANSMITTER TXD SCIDDR BIT = 1 TXD WOMS RECEIVER TRANSMITTER RXD NC GENERAL-PURPOSE I/O TXD TXD SCIDDR BIT = 0 RECEIVER RXD GENERAL-PURPOSE I/O Figure 16-25. Single-Wire Operation (LOOPS = 1, RSRC = 1) Technical Data 366 MMC2107 - Rev. 2.0 Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) Loop Operation Freescale Semiconductor, Inc... Enable single-wire operation by setting the LOOPS bit and the RSRC bit in SCICR1. Setting the LOOPS bit disables the path from the RXD pin to the receiver. Setting the RSRC bit connects the receiver input to the output of the TXD pin driver. Both the transmitter and receiver must be enabled (TE = 1 and RE = 1). The WOMS bit in the SCICR1 register configures the TXD pin for full CMOS drive or for open-drain drive. WOMS controls the TXD pin in both normal operation and in single-wire operation. When WOMS is set, the DDR bit for the TXD pin does not have to be cleared for transmitter to receive data. 16.14 Loop Operation In loop mode (LOOPS = 1, RSRC = 0), the transmitter output goes to the receiver input. The RXD pin is disconnected from the SCI and is available as a general-purpose I/O pin. Setting the DDR bit for the TXD pin connects the transmitter output to the TXD pin. Clearing the data direction bit disconnects the transmitter output from the TXD pin. TRANSMITTER TXD TXD SCIDDR BIT = 1 WOMS RECEIVER RXD H TXD TRANSMITTER TXD SCIDDR BIT = 0 GENERAL-PURPOSE I/O WOMS RECEIVER RXD GENERAL-PURPOSE I/O Figure 16-26. Loop Operation (LOOPS = 1, RSRC = 0) MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com 367 Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) Enable loop operation by setting the LOOPS bit and clearing the RSRC bit in SCICR1. Setting the LOOPS bit disables the path from the RXD pin to the receiver. Clearing the RSRC bit connects the transmitter output to the receiver input. Both the transmitter and receiver must be enabled (TE = 1 and RE = 1). Freescale Semiconductor, Inc... The WOMS bit in SCICR1 configures the TXD pin for full CMOS drive or for open-drain drive. WOMS controls the TXD pin during both normal operation and loop operation. 16.15 I/O Ports The SCIPORT register is associated with two pins: * The TXD pin is connected to SCIPORT1. * The RXD pin is connected to SCIPORT0. The SCI data direction register (SCIDDR) configures the pins as inputs or outputs. The SCI pullup and reduced drive register (SCIPURD) controls pin drive capability and enables or disables pullups. The WOMS bit in SCICR1 configures output ports as full CMOS drive outputs or as open-drain outputs. Table 16-9. SCI Port Control Summary Pullup Enable Control Reduced Drive Control Wired-OR Mode Control Register Bit Reset State Register Bit Reset State Register Bit Reset State SCIPURD PUPSCI 0 SCIPURD RDPSCI 0 SCICR1 WOMS CMOS drive Technical Data 368 MMC2107 - Rev. 2.0 Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) Reset 16.16 Reset Reset initializes the SCI registers to a known startup state as described in 16.7 Memory Map and Registers. 16.17 Interrupts Freescale Semiconductor, Inc... Table 16-10 lists the five interrupt requests associated with each SCI module. Table 16-10. SCI Interrupt Request Sources Source Transmitter Receiver Flag Enable Bit TDRE TIE TC TCIE RDRF RIE OR RIE IDLE ILIE 16.17.1 Transmit Data Register Empty The TDRE flag is set when the transmit shift register receives a byte from the SCI data register. It signals that SCIDRH and SCIDRL are empty and can receive new data to transmit. If the TIE bit in SCICR2 is also set, TDRE generates an interrupt request. Clear TDRE by reading SCISR1 and then writing to SCIDRL. Reset sets TDRE. 16.17.2 Transmission Complete The TC flag is set when TDRE = 1 and no data, preamble, or break frame is being transmitted. It signals that no transmission is in progress. If the TCIE bit is set in SCICR2, TC generates an interrupt request. When TC is set, the TXD pin is idle (logic 1). TC is cleared automatically when a data, preamble, or break frame is queued. Clear TC by reading SCISR1 with TC set and then writing to the SCIDRL register. TC cannot be cleared while a transmission is in progress. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com 369 Freescale Semiconductor, Inc. Serial Communications Interface Modules (SCI1 and SCI2) 16.17.3 Receive Data Register Full The RDRF flag is set when the data in the receive shift register transfers to SCIDRH and SCIDRL. It signals that the received data is available to be read. If the RIE bit is set in SCICR2, RDRF generates an interrupt request. Clear RDRF by reading SCISR1 and then reading SCIDRL. Freescale Semiconductor, Inc... 16.17.4 Idle Receiver Input The IDLE flag is set when 10 (if M = 0) or 11 (if M = 1) consecutive logic 1s appear on the receiver input. This signals an idle condition on the receiver input. If the ILIE bit in SCICR2 is set, IDLE generates an interrupt request. Once IDLE is cleared, a valid frame must again set the RDRF flag before an idle condition can set the IDLE flag. Clear IDLE by reading SCISR1 with IDLE set and then reading SCIDRL. 16.17.5 Overrun The OR flag is set if data is not read from SCIDRL before the receive shift register receives the stop bit of the next frame. This signals a receiver overrun condition. If the RIE bit in SCICR2 is set, OR generates an interrupt request. The data in the shift register is lost, but the data already in SCIDRH and SCIDRL is not affected. Clear OR by reading SCISR1 and then reading SCIDRL. Technical Data 370 MMC2107 - Rev. 2.0 Serial Communications Interface Modules (SCI1 and SCI2) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 17. Serial Peripheral Interface Module (SPI) Freescale Semiconductor, Inc... 17.1 Contents 17.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372 17.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372 17.4 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .373 17.5 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373 17.6 Signal Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374 17.6.1 MISO (Master In/Slave Out) . . . . . . . . . . . . . . . . . . . . . . . . 374 17.6.2 MOSI (Master Out/Slave In) . . . . . . . . . . . . . . . . . . . . . . . . 374 17.6.3 SCK (Serial Clock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375 17.6.4 SS (Slave Select) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375 17.7 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 375 17.7.1 SPI Control Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376 17.7.2 SPI Control Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378 17.7.3 SPI Baud Rate Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 379 17.7.4 SPI Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381 17.7.5 SPI Data Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382 17.7.6 SPI Pullup and Reduced Drive Register . . . . . . . . . . . . . . 383 17.7.7 SPI Port Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . .384 17.7.8 SPI Port Data Direction Register . . . . . . . . . . . . . . . . . . . . 385 17.8 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386 17.8.1 Master Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387 17.8.2 Slave Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387 17.8.3 Transmission Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . 388 17.8.3.1 Transfer Format When CPHA = 1 . . . . . . . . . . . . . . . . . 388 17.8.3.2 Transfer Format When CPHA = 0 . . . . . . . . . . . . . . . . . 390 17.8.4 SPI Baud Rate Generation. . . . . . . . . . . . . . . . . . . . . . . . . 393 17.8.5 Slave-Select Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393 17.8.6 Bidirectional Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com 371 Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) 17.8.7 Error Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .395 17.8.7.1 Write Collision Error . . . . . . . . . . . . . . . . . . . . . . . . . . . .395 17.8.7.2 Mode Fault Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395 17.8.8 Low-Power Mode Options . . . . . . . . . . . . . . . . . . . . . . . . . 396 17.8.8.1 Run Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396 17.8.8.2 Doze Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396 17.8.8.3 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396 Freescale Semiconductor, Inc... 17.9 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397 17.10 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397 17.10.1 SPI Interrupt Flag (SPIF) . . . . . . . . . . . . . . . . . . . . . . . . . . 397 17.10.2 Mode Fault (MODF) Flag . . . . . . . . . . . . . . . . . . . . . . . . . . 397 17.2 Introduction The serial peripheral interface (SPI) module allows full-duplex, synchronous, serial communication between the microcontroller unit (MCU) and peripheral devices. Software can poll the SPI status flags or SPI operation can be interrupt driven. 17.3 Features Features include: * Master mode and slave mode * Wired-OR mode * Slave-select output * Mode fault error flag with central processor unit (CPU) interrupt capability * Double-buffered operation * Serial clock with programmable polarity and phase * Control of SPI operation during doze mode * Reduced drive control for lower power consumption Technical Data 372 MMC2107 - Rev. 2.0 Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) Modes of Operation 17.4 Modes of Operation The SPI functions in these three modes: 1. Run mode -- Run mode is the normal mode of operation. 2. Doze mode -- Doze mode is a configurable low-power mode. 17.5 Block Diagram SPE MSTR WCOL SPI CONTROL SPIF SPI INTERRUPT REQUEST MODF SPIE SPI CLOCK PUPSP RDPSP SHIFT CONTROL LSBFE BAUD RATE GENERATOR DIVIDER 2 4 8 MISO 16 32 64 128 256 BAUD RATE SELECT CLOCK CONTROL SHIFT REGISTER MSB PIN CONTROL LSB SPIPORT Freescale Semiconductor, Inc... 3. Stop mode -- The SPI is inactive in stop mode. MOSI SCK SS SPPR[6:4] SPR[2:0] MSTR SPI DATA REGISTER CPOL SSOE CPHA SPISDOZ MSTR SWOM DDRSP[7:0] SPC0 IP INTERFACE Figure 17-1. SPI Block Diagram MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com 373 Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) 17.6 Signal Description An overview of the signals is provided in Table 17-1. Freescale Semiconductor, Inc... Table 17-1. Signal Properties Function(1) Name Port Reset State MISO SPIPORT0 Master data in/slave data out 0 MOSI SPIPORT1 Master data out/slave data in 0 SCK SPIPORT2 Serial clock 0 SS SPIPORT3 Slave select 0 1. The SPI ports (MISO, MOSI, SCK, and SS) are general-purpose I/O ports when the SPI is disabled (SPE = 0). 17.6.1 MISO (Master In/Slave Out) MISO is one of the two SPI data pins. In master mode, MISO is the data input. In slave mode, MISO is the data output and is three-stated until a master drives the SS input pin low. In bidirectional mode, a slave MISO pin is the SISO pin (slave in/slave out). In a multiple-master system, all MISO pins are tied together. 17.6.2 MOSI (Master Out/Slave In) MOSI is one of the two SPI data pins. In master mode, MOSI is the data output. In slave mode, MOSI is the data input. In bidirectional mode, a master MOSI pin is the MOMI pin (master out/master in). In a multiple-master system, all MOSI pins are tied together. Technical Data 374 MMC2107 - Rev. 2.0 Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) Memory Map and Registers 17.6.3 SCK (Serial Clock) The SCK pin is the serial clock pin for synchronizing transmissions between master and slave devices. In master mode, SCK is an output. In slave mode, SCK is an input. In a multiple-master system, all SCK pins are tied together. 17.6.4 SS (Slave Select) Freescale Semiconductor, Inc... In master mode, the SS pin can be: * A mode-fault input * A general-purpose input * A general-purpose output * A slave-select output In slave mode, the SS pin is always a slave-select input. 17.7 Memory Map and Registers Table 17-2 shows the SPI memory map. NOTE: Reading reserved addresses (0x00cb_004 and 0x00cb_0009 through 0x00cb_000b) and unimplemented addresses (0x00cb_000c through 0x00cb_000f) returns 0s. Writing to unimplemented addresses has no effect. Accessing unimplemented addresses does not generate an error response. Table 17-2. SPI Memory Map Address Bits 7-0 Access(1) 0x00cb_0000 SPI control register 1 (SPICR1) S/U 0x00cb_0001 SPI control register 2 (SPICR2) S/U 0x00cb_0002 SPI baud rate register (SPIBR) S/U 0x00cb_0003 SPI status register (SPISR) S/U 0x00cb_0005 SPI data register (SPIDR) S/U 0x00cb_0006 SPI pullup and reduced drive register (SPIPURD) S/U 0x00cb_0007 SPI port data register (SPIPORT) S/U 0x00cb_0008 SPI port data direction register (SPIDDR) S/U 1. S/U = CPU supervisor or user mode access. User mode accesses to supervisor only addresses have no effect and result in a cycle termination transfer error. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com 375 Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) 17.7.1 SPI Control Register 1 Address: 0x00cb_0000 Bit 7 6 5 4 3 2 1 Bit 0 SPIE SPE SWOM MSTR CPOL CPHA SSOE LSBFE 0 0 0 0 0 1 0 0 Read: Write: Reset: Freescale Semiconductor, Inc... Figure 17-2. SPI Control Register 1 (SPICR1) Read: Anytime Write: Anytime SPIE -- SPI Interrupt Enable Bit The SPIE bit enables the SPIF and MODF flags to generate interrupt requests. Reset clears SPIE. 1 = SPIF and MODF interrupt requests enabled 0 = SPIF and MODF interrupt requests disabled SPE -- SPI System Enable Bit The SPE bit enables the SPI and dedicates SPI port pins [3:0] to SPI functions. When SPE is clear, the SPI system is initialized but in a low-power disabled state. Reset clears SPE. 1 = SPI enabled 0 = SPI disabled SWOM -- SPI Wired-OR Mode Bit The SWOM bit configures the output buffers of SPI port pins [3:0] as open-drain outputs. SWOM controls SPI port pins [3:0] whether they are SPI outputs or general-purpose outputs. Reset clears SWOM. 1 = Output buffers of SPI port pins [3:0] open-drain 0 = Output buffers of SPI port pins [3:0] CMOS drive Technical Data 376 MMC2107 - Rev. 2.0 Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) Memory Map and Registers MSTR -- Master Bit The MSTR bit selects SPI master mode or SPI slave mode operation. Reset clears MSTR. 1 = Master mode 0 = Slave mode CPOL -- Clock Polarity Bit Freescale Semiconductor, Inc... The CPOL bit selects an inverted or non-inverted SPI clock. To transmit data between SPI modules, the SPI modules must have identical CPOL values. Reset clears CPOL. 1 = Active-low clock; SCK idles high 0 = Active-high clock; SCK idles low CPHA -- Clock Phase Bit The CPHA bit delays the first edge of the SCK clock. Reset sets CPHA. 1 = First SCK edge at start of transmission 0 = First SCK edge 1/2 cycle after start of transmission SSOE -- Slave Select Output Enable Bit The SSOE bit and the DDRSP3 bit configure the SS pin as a general-purpose input or a slave-select output. Reset clears SSOE. Table 17-3. SS Pin I/O Configurations DDRSP3 SSOE NOTE: Master Mode Slave Mode 0 0 Mode-fault input Slave-select input 0 1 General-purpose input Slave-select input 1 0 General-purpose output Slave-select input 1 1 Slave-select output Slave-select input Setting the SSOE bit disables the mode fault detect function. LSBFE -- LSB-First Enable Bit The LSBFE enables data to be transmitted LSB first. Reset clears LSBFE. 1 = Data transmitted LSB first. 0 = Data transmitted MSB first NOTE: In SPIDR, the MSB is always bit 7 regardless of the LSBFE bit. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com 377 Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) 17.7.2 SPI Control Register 2 Address: 0x00cb_0001 Read: Bit 7 6 5 4 3 2 0 0 0 0 0 0 1 Bit 0 SPISDOZ SPC0 0 0 Write: Freescale Semiconductor, Inc... Reset: 0 0 0 0 0 1 = Writes have no effect and the access terminates without a transfer error exception. Figure 17-3. SPI Control Register 2 (SPICR2) Read: Anytime Write: Anytime; writing to unimplemented bits has no effect SPISDOZ -- SPI Stop in Doze Bit The SPIDOZ bit stops the SPI clocks when the CPU is in doze mode. Reset clears SPISDOZ. 1 = SPI inactive in doze mode 0 = SPI active in doze mode SPC0 -- Serial Pin Control Bit 0 The SPC0 bit enables the bidirectional pin configurations shown in Table 17-4. Reset clears SPC0. Table 17-4. Bidirectional Pin Configurations Pin Mode SPC0 MSTR A MISO Pin(1) MOSI Pin(2) SCK Pin(3) 0 Slave data output Slave data input B 1 Master data input Master data output SCK output C 0 Slave data I/O GP(5) I/O SCK input Slave-select input 1 GP I/O Master data I/O SCK output MODF input (DDRSP3 = 0) or GP output (DDRSP3 = 1) Normal Bidirectional D SCK input SS Pin(4) 0 1 Slave-select input MODF input (DDRSP3 = 0) or GP output (DDRSP3 = 1) 1. Slave output is enabled if SPIDDR bit 0 = 1, SS = 0, and MSTR = 0 (A, C). 2. Master output is enabled if SPIDDR bit 1 = 1 and MSTR = 1 (B, D). 3. SCK output is enabled if SPIDDR bit 2 = 1 and MSTR = 1 (B, D). 4. SS output is enabled if SPIDDR bit 3 = 1, SPICR1 bit 1 (SSOE) = 1, and MSTR = 1 (B, D). 5. GP = General-purpose Technical Data 378 MMC2107 - Rev. 2.0 Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) Memory Map and Registers 17.7.3 SPI Baud Rate Register Address: 0x00cb_0002 Bit 7 Read: 6 5 4 SPPR6 SPPR5 SPPR4 0 0 0 0 3 2 1 Bit 0 SPR2 SPR1 SPR0 0 0 0 0 Write: Reset: 0 0 Freescale Semiconductor, Inc... = Writes have no effect and the access terminates without a transfer error exception. Figure 17-4. SPI Baud Rate Register (SPIBR) Read: Anytime Write: Anytime; writing to unimplemented bits has no effect SPPR[6:4] -- SPI Baud Rate Preselection Bits The SPPR[6:4] and SPR[2:0] bits select the SPI clock divisor as shown in Table 17-5. Reset clears SPPR[6:4] and SPR[2:0], selecting an SPI clock divisor of 2. SPR[2:0] -- SPI Baud Rate Bits The SPPR[6:4] and SPR[2:0] bits select the SPI clock divisor as shown in Table 17-5. Reset clears SPPR[6:4] and SPR[2:0], selecting an SPI clock divisor of 2. NOTE: Writing to SPIBR during a transmission may cause spurious results. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com 379 Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) Table 17-5. SPI Baud Rate Selection (33-MHz Module Clock) SPR[2:0] SPI Clock Divisor Baud Rate SPPR[6:4] SPR[2:0] SPI Clock Divisor Baud Rate 000 000 2 16.5 MHz 100 000 10 3.3 MHz 000 001 4 8.25 MHz 100 001 20 1.65 MHz 000 010 8 4.125 MHz 100 010 40 825 MHz 000 011 16 2.06 MHz 100 011 80 412.5 kHz 000 100 32 1.03 MHz 100 100 160 206.25 kHz 000 101 64 515.62 kHz 100 101 320 103.13 kHz 000 110 128 257.81 kHz 100 110 640 51.56 kHz 000 111 256 128.9 kHz 100 111 1280 25.78 kHz 001 000 4 8.25 MHz 101 000 12 2.75 MHz 001 001 8 4.12 MHz 101 001 24 1.375 MHz 001 010 16 2.06 MHz 101 010 48 687.5 kHz 001 011 32 1.03 MHz 101 011 96 343.75 kHz 001 100 64 515.62 kHz 101 100 192 171.88 kHz 001 101 128 257.81 kHz 101 101 384 85.94 kHz 001 110 256 128.9 kHz 101 110 768 42.97 kHz 001 111 512 64.45 kHz 101 111 1536 21.48 kHz 010 000 6 5.5 MHz 110 000 14 2.36 MHz 010 001 12 2.75 MHz 110 001 28 1.18 MHz 010 010 24 1.375 MHz 110 010 56 589.29 kHz 010 011 48 687.5 kHz 110 011 112 296.64 kHz 010 100 96 343.75 kHz 110 100 224 147.32 kHz 010 101 192 171.88 kHz 110 101 448 73.66 kHz 010 110 384 85.94 kHz 110 110 896 36.83 kHz 010 111 768 42.97 kHz 110 111 1792 18.42 kHz 011 000 8 4.13 MHz 111 000 16 2.06 MHz 011 001 16 2.06 MHz 111 001 32 1.03 MHz 011 010 32 1.03 MHz 111 010 64 515.63 kHz 011 011 64 515.63 kHz 111 011 128 257.81 kHz 011 100 128 257.81 kHz 111 100 256 128.91 kHz 011 101 256 128.91 kHz 111 101 512 64.45 kHz 011 110 512 64.45 kHz 111 110 1024 32.23 kHz 011 111 1024 32.23 kHz 111 111 2048 16.11 kHz Freescale Semiconductor, Inc... SPPR[6:4] Technical Data 380 MMC2107 - Rev. 2.0 Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) Memory Map and Registers 17.7.4 SPI Status Register Address: 0x00cb_0003 Read: Bit 7 6 5 4 3 2 1 Bit 0 SPIF WCOL 0 MODF 0 0 0 0 0 0 0 0 0 0 0 0 Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Freescale Semiconductor, Inc... Figure 17-5. SPI Status Register (SPISR) Read: Anytime Write: Has no meaning or effect SPIF -- SPI Interrupt Flag The SPIF flag is set after the eighth SCK cycle in a transmission when received data transfers from the shift register to SPIDR. If the SPIE bit is also set, SPIF generates an interrupt request. Once SPIF is set, no new data can be transferred into SPIDR until SPIF is cleared. Clear SPIF by reading SPISR with SPIF set and then accessing SPIDR. Reset clears SPIF. 1 = New data available in SPIDR 0 = No new data available in SPIDR WCOL -- Write Collision Flag The WCOL flag is set when software writes to SPIDR during a transmission. Clear WCOL by reading SPISR with WCOL set and then accessing SPIDR. Reset clears WCOL. 1 = Write collision 0 = No write collision MODF -- Mode Fault Flag The MODF flag is set when the SS pin of a master SPI is driven low and the SS pin is configured as a mode-fault input. If the SPIE bit is also set, MODF generates an interrupt request. A mode fault clears the SPE, MSTR, and DDRSP[2:0] bits. Clear MODF by reading SPISR with MODF set and then writing to SPICR1. Reset clears MODF. 1 = Mode fault 0 = No mode fault MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com 381 Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) 17.7.5 SPI Data Register Address: 0x00cb_0005 Bit 7 6 5 4 3 2 1 Bit 0 BIT 7 6 5 4 3 2 1 BIT 0 0 0 0 0 0 0 0 0 Read: Write: Reset: Freescale Semiconductor, Inc... Figure 17-6. SPI Data Register (SPIDR) Read: Anytime; normally read only after SPIF is set Write: Anytime; see WCOL SPIDR is both the input and output register for SPI data. Writing to SPIDR while a transmission is in progress sets the WCOL flag and disables the attempted write. Read SPIDR after the SPIF flag is set and before the end of the next transmission. If the SPIF flag is not serviced before a new byte enters the shift register, the new byte and any successive bytes are lost. The byte already in the SPIDR remains there until SPIF is serviced. Technical Data 382 MMC2107 - Rev. 2.0 Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) Memory Map and Registers 17.7.6 SPI Pullup and Reduced Drive Register Address: 0x00cb_0006 Read: Bit 7 6 0 0 5 4 RSVD5 RDPSP 0 0 3 2 0 0 1 Bit 0 RSVD1 PUPSP 0 0 Write: Reset: 0 0 0 0 Freescale Semiconductor, Inc... = Writes have no effect and the access terminates without a transfer error exception. Figure 17-7. SPI Pullup and Reduced Drive Register (SPIPURD) Read: Anytime Write: Anytime; writing to unimplemented bits has no effect RSVD5 and RSVD1 -- Reserved Writing to these read/write bits updates their values but has no effect on functionality. RDPSP -- SPI Port Reduced Drive Control Bit 1 = Reduced drive capability on SPIPORT bits [7:4] 0 = Full drive enabled on SPIPORT bits [7:4] PUPSP -- SPI Port Pullup Enable Bit 1 = Pullup devices enabled for SPIPORT bits [3:0] 0 = Pullup devices disabled for SPIPORT bits [3:0] MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com 383 Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) 17.7.7 SPI Port Data Register Address: 0x00cb_0007 Bit 7 6 5 4 3 RSVD7 RSVD6 RSVD5 RSVD4 0 0 0 0 2 1 Bit 0 Read: PORTSP3 PORTSP2 PORTSP1 PORTSP0 Write: Reset: Freescale Semiconductor, Inc... Pin function: 0 0 0 0 SS SCK MOSI/ MOMI MISO/ SISO Figure 17-8. SPI Port Data Register (SPIPORT) Read: Anytime Write: Anytime RSVD[7:4] -- Reserved Writing to these read/write bits updates their values but has no effect on functionality. PORTSP[3:0] -- SPI Port Data Bits Data written to SPIPORT drives pins only when they are configured as general-purpose outputs. Reading an input (DDRSP bit clear) returns the pin level; reading an output (DDRSP bit set) returns the pin driver input level. Writing to any of the PORTSP[3:0] pins does not change the pin state when the pin is configured for SPI output. SPIPORT I/O function depends upon the state of the SPE bit in SPICR1 and the state the DDRSP bits in SPIDDR. Table 17-6. SPI Port Summary Pullup Enable Control Wired-OR Mode Control Reduced Drive Control Register Bit Reset State Register Bit Reset State Register Bit Reset State SPIPURD PUPSP 0 SPIPURD RDPSP[1:0] Full drive SPICR1 SWOM Normal Technical Data 384 MMC2107 - Rev. 2.0 Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) Memory Map and Registers 17.7.8 SPI Port Data Direction Register Address: 0x00cb_0008 Bit 7 6 5 4 3 2 1 Bit 0 RSVD7 RSVD6 RSVD5 RSVD4 DDRSP3 DDRSP2 DDRSP1 DDRSP0 0 0 0 0 0 0 0 0 SS SCK MOSI/ MOMI MISO/ SISO Read: Write: Reset: Freescale Semiconductor, Inc... Pin function: Figure 17-9. SPI Port Data Direction Register (SPIDDR) Read: Anytime Write: Anytime RSVD[7:4] -- Reserved Writing to these read/write bits updates their values but has no effect on functionality. DDRSP[3:0] -- Data Direction Bits The DDRSP[3:0] bits control the data direction of SPIPORT pins. Reset clears DDRSP[3:0]. 1 = Corresponding pin configured as output 0 = Corresponding pin configured as input In slave mode, DDRSP3 has no meaning or effect. In master mode, DDRSP3 determines whether SPI port pin 3 is a mode-fault input, a general-purpose output, or a slave-select output. NOTE: When the SPI is enabled (SPE = 1), the MISO, MOSI, and SCK pins: * Are inputs if their SPI functions are input functions regardless of the state of their DDRSP bits. * Are outputs if their SPI functions are output functions only if their DDRSP bits are set. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com 385 Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) 17.8 Functional Description The SPI module allows full-duplex, synchronous, serial communication between the MCU and peripheral devices. Software can poll the SPI status flags or SPI operation can be interrupt driven. Freescale Semiconductor, Inc... Setting the SPE bit in SPICR1 enables the SPI and dedicates four SPI port pins to SPI functions: * Slave select (SS) * Serial clock (SCK) * Master out/slave in (MOSI) * Master in/slave out (MISO) When the SPE bit is clear, the SS, SCK, MOSI, and MISO pins are general-purpose I/O pins controlled by SPIDDR. The 8-bit shift register in a master SPI is linked by the MOSI and MISO pins to the 8-bit shift register in the slave. The linked shift registers form a distributed 16-bit register. In an SPI transmission, the SCK clock from the master shifts the data in the 16-bit register eight bit positions, and the master and slave exchange data. Data written to the master SPIDR register is the output data to the slave. After the exchange, data read from the master SPIDR is the input data from the slave. SPIDR SHIFT REGISTER BAUD RATE GENERATOR SPIDR MISO MISO MOSI MOSI SCK SCK SS VDD SHIFT REGISTER SS MASTER SPI SLAVE SPI Figure 17-10. Full-Duplex Operation Technical Data 386 MMC2107 - Rev. 2.0 Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) Functional Description 17.8.1 Master Mode Setting the MSTR bit in SPICR1 puts the SPI in master mode. Only a master SPI can initiate a transmission. Writing to the master SPIDR begins a transmission. If the shift register is empty, the byte transfers to the shift register and begins shifting out on the MOSI pin under the control of the master SCK clock. The SCK clock starts one-half SCK cycle after writing to SPIDR. Freescale Semiconductor, Inc... The SPR[2:0] and SPPR[6:4] bits in SPIBR control the baud rate generator and determine the speed of the shift register. The SCK pin is the SPI clock output. Through the SCK pin, the baud rate generator of the master controls the shift register of the slave. The MSTR bit in SPICR1 and the SPC0 bit in SPICR2 control the function of the data pins, MOSI and MISO. The SS pin is normally an input that remains in the inactive high state. Setting the DDRSP3 bit in SPIDDR configures SS as an output. The DDRSP3 bit and the SSOE bit in SPICR1 can configure SS for general-purpose I/O, mode fault detection, or slave selection. See Table 17-3. The SS output goes low during each transmission and is high when the SPI is in the idle state. Driving the master SS input low sets the MODF flag in SPISR, indicating a mode fault. More than one master may be trying to drive the MOSI and SCK lines simultaneously. A mode fault clears the data direction bits of the MISO, MOSI (or MOMI), and SCK pins to make them inputs. A mode fault also clears the SPE and MSTR bits in SPICR1. If the SPIE bit is also set, the MODF flag generates an interrupt request. 17.8.2 Slave Mode Clearing the MSTR bit in SPICR1 puts the SPI in slave mode. The SCK pin is the SPI clock input from the master, and the SS pin is the slave-select input. For a transmission to occur, the SS pin must be driven low and remain low until the transmission is complete. The MSTR bit and the SPC0 bit in SPICR2 control the function of the data pins, MOSI and MISO. The SS input also controls the MISO pin. If SS is low, the MSB in the shift register shifts out on the MISO pin. If SS MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com 387 Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) is high, the MISO pin is in a high impedance state, and the slave ignores the SCK input. NOTE: When using peripherals with full-duplex capability, do not simultaneously enable two receivers that drive the same MISO output line. Freescale Semiconductor, Inc... As long as only one slave drives the master input line, it is possible for several slaves to receive the same transmission simultaneously. If the CPHA bit in SPICR1 is clear, odd-numbered edges on the SCK input latch the data on the MOSI pin. Even-numbered edges shift the data into the LSB position of the SPI shift register and shift the MSB out to the MISO pin. If the CPHA bit is set, even-numbered edges on the SCK input latch the data on the MOSI pin. Odd-numbered edges shift the data into the LSB position of the SPI shift register and shift the MSB out to the MISO pin. The transmission is complete after the eighth shift. The received data transfers to SPIDR, setting the SPIF flag in SPISR. 17.8.3 Transmission Formats The CPHA and CPOL bits in SPICR1 select one of four combinations of serial clock phase and polarity. Clock phase and polarity must be identical for the master SPI device and the communicating slave device. 17.8.3.1 Transfer Format When CPHA = 1 Some peripherals require the first SCK edge to occur before the slave MSB becomes available at its MISO pin. When the CPHA bit is set, the master SPI waits for a synchronization delay of one-half SCK clock cycle. Then it issues the first SCK edge at the beginning of the transmission. The first edge causes the slave to transmit its MSB to the MISO pin of the master. The second edge and the following even-numbered edges latch the data. The third edge and the following odd-numbered edges shift the latched slave data into the master shift register and shift master data out on the master MOSI pin. Technical Data 388 MMC2107 - Rev. 2.0 Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) Functional Description * Data that was in the master SPIDR register is in the slave SPIDR. Data that was in the slave SPIDR register is in the master SPIDR. * The SCK clock stops and the SPIF flag in SPISR is set, indicating that the transmission is complete. If the SPIE bit in SPCR1 is set, SPIF generates an interrupt request. Figure 17-11 shows the timing of a transmission with the CPHA bit set. The SS pin of the master must be either high or configured as a general-purpose output not affecting the SPI. BEGIN TRANSMISSION END TRANSMISSION SCK (CPOL = 0) SCK (CPOL = 1) IF NEXT TRANSFER BEGINS HERE Freescale Semiconductor, Inc... After the 16th and final SCK edge: SAMPLE INPUT MOSI/MISO CHANGE OUTPUT MOSI PIN CHANGE OUTPUT MISO PIN SS PIN OUTPUT MASTER ONLY SLAVE SS PIN tL MSB FIRST (LSBFE = 0): LSB FIRST (LSBFE = 1): tT MSB LSB BIT 6 BIT 1 BIT 5 BIT 2 BIT 4 BIT 3 BIT 3 BIT 4 BIT 2 BIT 5 BIT 1 BIT 6 LSB MSB tI tL MINIMUM 1/2 SCK FOR tT, tL, tl Legend: tL = Minimum leading time before the first SCK edge tT = Minimum trailing time after the last SCK edge tI = Minimum idling time between transmissions (minimum SS high time) tL, tT , and tI are guaranteed for master mode and required for slave mode. Figure 17-11. SPI Clock Format 1 (CPHA = 1) MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com 389 Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) When CPHA = 1, the slave SS line can remain low between bytes. This format is good for systems with a single master and a single slave driving the MISO data line. Writing to SPIDR while a transmission is in progress sets the WCOL flag to indicate a write collision and inhibits the write. WCOL does not generate an interrupt request; the SPIF interrupt request comes at the end of the transfer that was in progress at the time of the error. Freescale Semiconductor, Inc... 17.8.3.2 Transfer Format When CPHA = 0 In some peripherals, the slave MSB is available at its MISO pin as soon as the slave is selected. When the CPHA bit is clear, the master SPI delays its first SCK edge for half a SCK cycle after the transmission starts. The first edge and all following odd-numbered edges latch the slave data. Even-numbered SCK edges shift slave data into the master shift register and shift master data out on the master MOSI pin. After the 16th and final SCK edge: * Data that was in the master SPIDR is in the slave SPIDR. Data that was in the slave SPIDR is in the master SPIDR. * The SCK clock stops and the SPIF flag in SPISR is set, indicating that the transmission is complete. If the SPIE bit in SPCR1 is set, SPIF generates an interrupt request. Figure 17-12 shows the timing of a transmission with the CPHA bit clear. The SS pin of the master must be either high or configured as a general-purpose output not affecting the SPI. Technical Data 390 MMC2107 - Rev. 2.0 Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) Functional Description BEGIN TRANSMISSION END TRANSMISSION SCK (CPOL = 0) IF NEXT TRANSFER BEGINS HERE SCK (CPOL = 1) SAMPLE INPUT MOSI/MISO Freescale Semiconductor, Inc... CHANGE OUTPUT MOSI PIN CHANGE OUTPUT MISO PIN SS PIN OUTPUT MASTER ONLY SLAVE SS PIN tL MSB FIRST (LSBFE = 0): LSB FIRST (LSBFE = 1): tT MSB LSB Bit 6 Bit 1 Bit 5 Bit 2 Bit 4 Bit 3 Bit 3 Bit 4 Bit 2 Bit 5 Bit 1 Bit 6 LSB MSB tI tL MINIMUM 1/2 SCK FOR tT, tL, tl Legend: tL = Minimum leading time before the first SCK edge tT = Minimum trailing time after the last SCK edge tI = Minimum idling time between transmissions (minimum SS high time) tL, tT, and tI are guaranteed for master mode and required for slave mode. Figure 17-12. SPI Clock Format 0 (CPHA = 0) When CPHA = 0, the slave SS pin must be negated and reasserted between bytes. NOTE: Clock skew between the master and slave can cause data to be lost when: * CPHA = 0, and, * The baud rate is the SPI clock divided by two, and * The master SCK frequency is half the slave SPI clock frequency, and * Software writes to the slave SPIDR just before the synchronized SS signal goes low. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com 391 Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) SCK (CPOL = 0) SCK (CPOL = 1) SAMPLE I MOSI/MISO CHANGE O MOSI PIN Freescale Semiconductor, Inc... CHANGE O MISO PIN SS PIN (I) SPI CLOCK SS SYNCHRONIZED TO SPI CLOCK MISO PIN SPIDR WRITE THIS CYCLE Figure 17-13. Transmission Error Due to Master/Slave Clock Skew The synchronized SS signal is synchronized to the SPI clock. Figure 17-13 shows an example with the synchronized SS signal almost a full SPI clock cycle late. While the synchronized SS of the slave is high, writing is allowed even though the SS pin is already low. The write can change the MISO pin while the master is sampling the MISO line. The first bit of the transfer may not be stable when the master samples it, so the byte sent to the master may be corrupted. Also, if the slave generates a late write, its state machine may not have time to reset, causing it to incorrectly receive a byte from the master. This error is most likely when the SCK frequency is half the slave SPI clock frequency. At other baud rates, the SCK skew is no more than one SPI clock, and there is more time between the synchronized SS signal and the first SCK edge. For example, with a SCK frequency one-fourth Technical Data 392 MMC2107 - Rev. 2.0 Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) Functional Description the slave SPI clock frequency, there are two SPI clocks between the fall of SS and the SCK edge. As long as another late SPIDR write does not occur, the following bytes to and from the slave are correctly transmitted. Freescale Semiconductor, Inc... 17.8.4 SPI Baud Rate Generation The baud rate generator divides the SPI clock to produce the SPI baud clock. The SPPR[6:4] and SPR[2:0] bits in SPIBR select the SPI clock divisor: SPI clock divisor = (SPPR + 1) x 2(SPR+1) where: SPPR = the value written to bits SPPR[6:4] SPR = the value written to bits SPR[2:0] The baud rate generator is active only when the SPI is in master mode and transmitting. Otherwise, the divider is inactive to reduce IDD current. 17.8.5 Slave-Select Output The slave-select output feature automatically drives the SS pin low during transmission to select external devices and drives it high during idle to deselect external devices. When SS output is selected, the SS output pin is connected to the SS input pin of the external device. In master mode only, setting the SSOE bit in SPICR1 and the DDRSP[3] bit in SPIDDR configures the SS pin as a slave-select output. Setting the SSOE bit disables the mode fault feature. NOTE: Be careful when using the slave-select output feature in a multimaster system. The mode fault feature is not available for detecting system errors between masters. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com 393 Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) 17.8.6 Bidirectional Mode Setting the SPC0 bit in SPICR1 selects bidirectional mode (see Table 17-7). The SPI uses only one data pin for the interface with external device(s). The MSTR bit determines which pin to use. In master mode, the MOSI pin is the master out/master in pin, MOMI. In slave mode, the MISO pin is the slave out/slave in pin, SISO. The MISO pin in master mode and MOSI pin in slave mode are general-purpose I/O pins. Freescale Semiconductor, Inc... The direction of each data I/O pin depends on its data direction register bit. A pin configured as an output is the output from the shift register. A pin configured as an input is the input to the shift register, and data coming out of the shift register is discarded. The SCK pin is an output in master mode and an input in slave mode. The SS pin can be an input or an output in master mode, and it is always an input in slave mode. In bidirectional mode, a mode fault does not clear DDRSP0, the data direction bit for the SISO pin. Table 17-7. Normal Mode and Bidirectional Mode SPE = 1 Master Mode, MSTR = 1 SERIAL OUT Normal Mode SPC0 = 0 SPI MOSI MISO SWOM enables open drain output. SERIAL OUT Bidirectional Mode SPC0 = 1 SPI SERIAL IN SERIAL IN SPI DDRSP1 SERIAL IN Slave Mode, MSTR = 0 MOMI SERIAL OUT SPI PORT PIN 0 SWOM enables open drain output. SPI port pin 0 is general-purpose I/O. SPI PORT PIN 1 SERIAL IN SERIAL OUT DDRSP0 SISO SWOM enables open drain output. SPI port pin 1 is general-purpose I/O. Technical Data 394 MISO SWOM enables open drain output. SPI DDRSP1 MOSI DDRSP0 MMC2107 - Rev. 2.0 Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) Functional Description 17.8.7 Error Conditions The SPI has two error conditions: * Write collision error * Mode fault error Freescale Semiconductor, Inc... 17.8.7.1 Write Collision Error The WCOL flag in SPISR indicates that a serial transfer was in progress when the MCU tried to write new data to SPIDR. Valid write times are listed below (see Figure 17-11 and Figure 17-12 for definitions of tT and tI): * In master mode, a valid write is within tI (when SS is high). * In slave phase 0, a valid write within tI (when SS is high). * In slave phase 1, a valid write is within tT or tI (after the last SCK edge and before SS goes low), excluding the first two SPI clocks after the last SCK edge (the beginning of tT is an illegal write). A write during any other time causes a WCOL error. The write is disabled to avoid writing over the data being transmitted. WCOL does not generate an interrupt request because the WCOL flag can be read upon completion of the transmission that was in progress at the time of the error. 17.8.7.2 Mode Fault Error If the SS input of a master SPI goes low, it indicates a system error in which more than one master may be trying to drive the MOSI and SCK lines simultaneously. This condition is not permitted in normal operation; it sets the MODF flag in SPISR. If the SPIE bit in SPICR1 is also set, MODF generates an interrupt request. Configuring the SS pin as a general-purpose output or a slave-select output disables the mode fault function. A mode fault clears the SPE and MSTR bits and the DDRSP bits of the SCK, MISO, and MOSI (or MOMI) pins. This forces those pins to be high-impedance inputs to avoid any conflict with another output driver. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com 395 Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) If the mode fault error occurs in bidirectional mode, the DDRSP bit of the SISO pin is not affected, since it is a general-purpose I/O pin. 17.8.8 Low-Power Mode Options This subsection describes the low-power mode options. Freescale Semiconductor, Inc... 17.8.8.1 Run Mode Clearing the SPE bit in SPICR1 puts the SPI in a disabled, low-power state. SPI registers are accessible, but SPI clocks are disabled. 17.8.8.2 Doze Mode SPI operation in doze mode depends on the state of the SPISDOZ bit in SPICR2. * If SPISDOZ is clear, the SPI operates normally in doze mode. * If SPISDOZ is set, the SPI clock stops, and the SPI enters a low-power state in doze mode. - Any master transmission in progress stops at doze mode entry and resumes at doze mode exit. - Any slave transmission in progress continues if a master continues to drive the slave SCK pin. The slave stays synchronized to the master SCK clock. NOTE: Although the slave shift register can receive MOSI data, it cannot transfer data to SPIDR or set the SPIF flag in doze or stop mode. If the slave enters doze mode in an idle state and exits doze mode in an idle state, SPIF remains clear and no transfer to SPIDR occurs. 17.8.8.3 Stop Mode SPI operation in stop mode is the same as in doze mode with the SPISDOZ bit set. Technical Data 396 MMC2107 - Rev. 2.0 Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Serial Peripheral Interface Module (SPI) Reset 17.9 Reset Reset initializes the SPI registers to a known startup state as described in 17.7 Memory Map and Registers. A transmission from a slave after reset and before writing to the SPIDR register is either indeterminate or the byte last received from the master before the reset. Reading the SPIDR after reset returns 0s. Freescale Semiconductor, Inc... 17.10 Interrupts Table 17-8. SPI Interrupt Request Sources Interrupt Request Mode fault Flag Enable Bit MODF SPIE Transmission complete SPIF 17.10.1 SPI Interrupt Flag (SPIF) SPIF is set after the eighth SCK cycle in a transmission when received data transfers from the shift register to SPIDR. If the SPIE bit is also set, SPIF generates an interrupt request. Once SPIF is set, no new data can be transferred into SPIDR until SPIF is cleared. Clear SPIF by reading SPISR with SPIF set and then accessing SPIDR. Reset clears SPIF. 17.10.2 Mode Fault (MODF) Flag MODF is set when the SS pin of a master SPI is driven low and the SS pin is configured as a mode-fault input. If the SPIE bit is also set, MODF generates an interrupt request. A mode fault clears the SPE, MSTR, and DDRSP[2:0] bits. Clear MODF by reading SPISR with MODF set and then writing to SPICR1. Reset clears MODF. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com 397 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Serial Peripheral Interface Module (SPI) Technical Data 398 MMC2107 - Rev. 2.0 Serial Peripheral Interface Module (SPI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 18. Queued Analog-to-Digital Converter (QADC) Freescale Semiconductor, Inc... 18.1 Contents 18.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 401 18.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 402 18.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 403 18.5 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .404 18.5.1 Debug Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 404 18.5.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .405 18.6 Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405 18.6.1 Port QA Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406 18.6.1.1 Port QA Analog Input Pins . . . . . . . . . . . . . . . . . . . . . . .406 18.6.1.2 Port QA Digital Input/Output Pins . . . . . . . . . . . . . . . . . 407 18.6.2 Port QB Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407 18.6.2.1 Port QB Analog Input Pins . . . . . . . . . . . . . . . . . . . . . . .407 18.6.2.2 Port QB Digital Input Pins . . . . . . . . . . . . . . . . . . . . . . .407 18.6.3 External Trigger Input Pins. . . . . . . . . . . . . . . . . . . . . . . . . 408 18.6.4 Multiplexed Address Output Pins . . . . . . . . . . . . . . . . . . . . 408 18.6.5 Multiplexed Analog Input Pins . . . . . . . . . . . . . . . . . . . . . . 409 18.6.6 Voltage Reference Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . 409 18.6.7 Dedicated Analog Supply Pins . . . . . . . . . . . . . . . . . . . . . . 409 18.7 Memory Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409 18.8 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411 18.8.1 QADC Module Configuration Register . . . . . . . . . . . . . . . . 411 18.8.2 QADC Test Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412 18.8.3 Port Data Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412 18.8.4 Port QA Data Direction Register . . . . . . . . . . . . . . . . . . . . 414 18.8.5 Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .416 18.8.5.1 Control Register 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 416 18.8.5.2 Control Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419 18.8.5.3 QADC Control Register 2. . . . . . . . . . . . . . . . . . . . . . . . 422 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 399 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) 18.8.6 Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .427 18.8.6.1 QADC Status Register 0 . . . . . . . . . . . . . . . . . . . . . . . . 427 18.8.6.2 QADC Status Register 1 . . . . . . . . . . . . . . . . . . . . . . . . 436 18.8.7 Conversion Command Word Table . . . . . . . . . . . . . . . . . .437 18.8.8 Result Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .441 18.8.8.1 Right-Justified Unsigned Result Register. . . . . . . . . . . . 441 18.8.8.2 Left-Justified Signed Result Register . . . . . . . . . . . . . . . 442 18.8.8.3 Left-Justified Unsigned Result Register . . . . . . . . . . . . . 442 Freescale Semiconductor, Inc... 18.9 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443 18.9.1 QADC Bus Accessing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443 18.9.2 External Multiplexing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443 18.9.2.1 External Multiplexing Operation . . . . . . . . . . . . . . . . . . .443 18.9.2.2 Module Version Options. . . . . . . . . . . . . . . . . . . . . . . . . 444 18.9.2.3 External Multiplexed Address Configuration . . . . . . . . .446 18.9.3 Analog Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 446 18.9.3.1 Analog-to-Digital Converter Operation . . . . . . . . . . . . . .446 18.9.3.2 Conversion Cycle Times . . . . . . . . . . . . . . . . . . . . . . . . 446 18.9.3.3 Channel Decode and Multiplexer . . . . . . . . . . . . . . . . . . 448 18.9.3.4 Sample Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .448 18.9.3.5 Digital-to-Analog Converter (DAC) Array . . . . . . . . . . . . 449 18.9.3.6 Comparator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449 18.9.3.7 Bias . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449 18.9.3.8 Successive-Approximation Register . . . . . . . . . . . . . . . 449 18.9.3.9 State Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .450 18.10 Digital Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .450 18.10.1 Queue Priority Timing Examples. . . . . . . . . . . . . . . . . . . . 450 18.10.1.1 Queue Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .451 18.10.1.2 Queue Priority Schemes . . . . . . . . . . . . . . . . . . . . . . . . 453 18.10.2 Boundary Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 465 18.10.3 Scan Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 466 18.10.4 Disabled Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 467 18.10.5 Reserved Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 467 18.10.6 Single-Scan Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 467 18.10.6.1 Software-Initiated Single-Scan Mode. . . . . . . . . . . . . . . 468 18.10.6.2 External Trigger Single-Scan Mode . . . . . . . . . . . . . . . . 469 18.10.6.3 External Gated Single-Scan Mode. . . . . . . . . . . . . . . . . 470 18.10.6.4 Interval Timer Single-Scan Mode. . . . . . . . . . . . . . . . . . 470 Technical Data 400 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Introduction Freescale Semiconductor, Inc... 18.10.7 Continuous-Scan Modes . . . . . . . . . . . . . . . . . . . . . . . . . . 472 18.10.7.1 Software-Initiated Continuous-Scan Mode. . . . . . . . . . . 473 18.10.7.2 External Trigger Continuous-Scan Mode . . . . . . . . . . . . 474 18.10.7.3 External Gated Continuous-Scan Mode . . . . . . . . . . . . 474 18.10.7.4 Periodic Timer Continuous-Scan Mode . . . . . . . . . . . . . 475 18.10.8 QADC Clock (QCLK) Generation . . . . . . . . . . . . . . . . . . . . 476 18.10.9 Periodic/Interval Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . .480 18.10.10 Conversion Command Word Table . . . . . . . . . . . . . . . . . .481 18.10.11 Result Word Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 485 18.11 Pin Connection Considerations . . . . . . . . . . . . . . . . . . . . . . .486 18.11.1 Analog Reference Pins. . . . . . . . . . . . . . . . . . . . . . . . . . . .486 18.11.2 Analog Power Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 486 18.11.3 Conversion Timing Schemes . . . . . . . . . . . . . . . . . . . . . . .488 18.11.4 Analog Supply Filtering and Grounding . . . . . . . . . . . . . . . 490 18.11.5 Accommodating Positive/Negative Stress Conditions . . . .494 18.11.6 Analog Input Considerations . . . . . . . . . . . . . . . . . . . . . . .495 18.11.7 Analog Input Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 497 18.11.7.1 Settling Time for the External Circuit . . . . . . . . . . . . . . . 498 18.11.7.2 Error Resulting from Leakage . . . . . . . . . . . . . . . . . . . . 499 18.12 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 18.12.1 Interrupt Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 18.12.2 Interrupt Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .501 18.2 Introduction The queued analog-to-digital converter (QADC) is a 10-bit, unipolar, successive approximation converter. A minimum of eight analog input channels can be supported using internal multiplexing. A maximum of 18 input channels can be supported in the expanded, externally multiplexed mode. The actual number of channels depends upon the number of pins available to the QADC module. The QADC consists of an analog front-end and a digital control subsystem, which includes an IPbus interface block. The analog section includes input pins, an analog multiplexer, and sample and hold analog circuits. The analog conversion is performed by MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 401 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) the digital-to-analog converter (DAC) resistor-capacitor (RC) array and a high-gain comparator. The digital control section contains queue control logic to sequence the conversion process and interrupt generation logic. Also included are the periodic/interval timer, control and status registers, the conversion command word (CCW) table, random-access memory (RAM), and the result table RAM. Freescale Semiconductor, Inc... The bus interface unit (BIU) allows the QADC to operate with the applications software through the IPbus environment. 18.3 Features Features of the QADC module include: * Internal sample and hold * Up to eight analog input channels using internal multiplexing * Directly supports up to four external multiplexers (for example, the MC14051) * Up to 18 total input channels with internal and external multiplexing * Programmable input sample time for various source impedances * Two conversion command queues with a total of 64 entries * Sub-queues possible using pause mechanism * Queue complete and pause software interrupts available on both queues * Queue pointers indicate current location for each queue * Automated queue modes initiated by: - External edge trigger and gated trigger - Periodic/interval timer, within QADC module [queues 1 and 2] - Software command * Single-scan or continuous-scan of queues * 64 result registers Technical Data 402 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Block Diagram * Output data readable in three formats: - Right-justified unsigned - Left-justified signed - Left-justified unsigned * Unused analog channels can be used as digital ports Freescale Semiconductor, Inc... 18.4 Block Diagram EXTERNAL MUX ADDRESS ANALOG POWER INPUTS 8 ANALOG CHANNELS (4 GPIO) REFERENCE INPUTS EXTERNAL TRIGGERS ANALOG INPUT MUX AND DIGITAL PIN FUNCTIONS 10-BIT ANALOG-TO-DIGITAL CONVERTER DIGITAL CONTROL 64-ENTRY QUEUE OF 10-BIT CONVERSION COMMAND WORDS (CCWs) IP INTERFACE 64-ENTRY TABLE OF 10-BIT RESULTS 10-BIT TO 16-BIT RESULT ALIGNMENT Figure 18-1. QADC Block Diagram MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 403 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) 18.5 Modes of Operation This subsection describes the two modes of operation: * Debug mode * Stop mode 18.5.1 Debug Mode Freescale Semiconductor, Inc... If the QDBG bit in the module configuration register (QADCMCR) is set, then the QADC enters debug mode when background debug mode is enabled and a breakpoint is processed. When in debug mode and the QDBG bit is set, the QADC finishes any conversion in progress and then freezes. Depending on when debug mode is asserted, the three possible queue freeze scenarios are: * When a queue is not executing, the QADC freezes immediately. * When a queue is executing, the QADC completes the current conversion and then freezes. * If during the execution of the current conversion, the queue operating mode for the active queue is changed, or a queue 2 abort occurs, the QADC freezes immediately. When the QADC enters debug mode while a queue is active, the current CCW location of the queue pointer is saved. Debug mode: * Stops the analog clock * Holds the periodic/interval timer in reset * Prevents external trigger events from being captured * Keeps all QADC registers and RAM accessible Although the QADC saves a pointer to the next CCW in the current queue, the software can force the QADC to execute a different CCW by writing new queue operating modes for normal operation. The QADC looks at the queue operating modes, the current queue pointer, and any pending trigger events to decide which CCW to execute. Technical Data 404 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Signals 18.5.2 Stop Mode The QADC enters a low-power idle state whenever the QSTOP bit is set or the part is in stop mode. Freescale Semiconductor, Inc... QADC stop: * Disables the analog-to-digital converter, effectively turning off the analog circuit. * Aborts the conversion sequence in progress * Changes the data direction register (DDRQA), port data registers (PORTQA and PORTQB), control registers (QACR2, QACR1, and QACR0) and the status registers (QASR1 and QASR0) to read-only. Only the module configuration register (QADCMCR) is writable. * Causes the RAM to not be accessible, can not read valid results from RAM (result word table and CCW) nor write to the RAM (result word table and CCW). * Resets QACR1, QACR2, QASR0, and QASR1 * Holds the QADC periodic/interval timer in reset Because the bias currents to the analog circuit are turned off in stop, the QADC requires some recovery time (tSR) to stabilize the analog circuits. 18.6 Signals The QADC uses the external pins shown in Figure 18-2. There are eight channel/port pins that can support up to 18 channels when external multiplexing is used (including internal channels). All of the channel pins can also be used as general-purpose digital port pins. In addition, there are also two analog reference pins and two analog submodule power pins. The QADC has external trigger inputs and the multiplexer outputs combined onto some of the channel pins. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 405 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) 18.6.1 Port QA Pin Functions The four port QA pins can be used as analog inputs or as a bidirectional 4-bit digital input/output port. 18.6.1.1 Port QA Analog Input Pins INTERNAL DIGITAL POWER SHARED WITH OTHER MODULES VSSI VDDI ANALOG POWER AND GROUND VSSA VDDA ANALOG REFERENCES VRH VRL PORT QB ANALOG INPUTS EXTERNAL MUX INPUTS DIGITAL INPUTS PORT QA ANALOG INPUTS EXTERNAL TRIGGER INPUTS EXTERNAL MUX ADDRESS OUTPUTS DIGITAL I/O AN0/ANW/PQB0 AN1/ANX/PQB1 AN2/ANY/PQB2 AN3/ANZ/PQB3 AN52/MA0/PQA0 AN53/MA1/PQA1 PORT QB Freescale Semiconductor, Inc... When used as analog inputs, the four port QA pins are referred to as AN[56:55, 53:52]. Due to the digital output drivers associated with port QA, the analog characteristics of port QA may be different from those of port QB. ANALOG MUX AND PORT LOGIC ANALOG CONVERTER DIGITAL RESULTS AND CONTROL AN55/ETRIG1/PQA3 AN56/ETRIG2/PQA4 Figure 18-2. QADC Input and Output Signals Technical Data 406 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Signals 18.6.1.2 Port QA Digital Input/Output Pins Port QA pins are referred to as PQA[4:3, 1:0] when used as a bidirectional 4-bit digital input/output port. These four pins may be used for general-purpose digital input signals or digital output signals. Freescale Semiconductor, Inc... Port QA pins are connected to a digital input synchronizer during reads and may be used as general-purpose digital inputs when the applied voltages meet high-voltage input (VIH) and low-voltage input (VIL) requirements. Each port QA pin is configured as an input or output by programming the upper half of the port data direction register (DDRQA). The digital input signal states are read by the software in the upper half of the port data register when the port data direction register specifies that the pins are inputs. The digital data in the port data register is driven onto the port QA pins when the corresponding bit in the port data direction register specifies output. Since the outputs are configured as output drivers, external pullup provisions are not necessary when the output is used to drive another integrated circuit. 18.6.2 Port QB Pin Functions The four port QB pins can be used as analog inputs or as an 4-bit digital input-only port. 18.6.2.1 Port QB Analog Input Pins When used as analog inputs, the four port QB pins are referred to as AN[3:0]. Since port QB functions as analog and digital input only, the analog characteristics may be different from those of port QA. 18.6.2.2 Port QB Digital Input Pins Port QB pins are referred to as PQB[3:0] when used as an 4-bit digital input only port. In addition to functioning as analog input pins, the port QB pins are also connected to the input of a synchronizer during reads and may be used as general-purpose digital inputs when the applied voltages meet VIH and VIL requirements. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 407 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Since port QB pins are input only, a data direction register is not necessary. The digital input signal states are read by the software in the lower half of the port data register. Freescale Semiconductor, Inc... 18.6.3 External Trigger Input Pins The QADC uses two external trigger pins (ETRIG[2:1]). Each of the two input external trigger pins is associated with one of the scan queues, queue 1 or queue 2. The assignment of ETRIG[2:1] to a queue is made in QACR0 by the TRG bit. When TRG = 0, ETRIG1 triggers queue 1 and ETRIG2 triggers queue 2. When TRG = 1, ETRIG1 triggers queue 2 and ETRIG2 triggers queue 1. 18.6.4 Multiplexed Address Output Pins In the non-multiplexed mode, the eight channel pins are connected to an internal multiplexer which routes the analog signals into the internal A/D converter. In the externally multiplexed mode, the QADC allows automatic channel selection through up to four external 4-to-1 selector chips. The QADC provides a 2-bit multiplexed address output to the external multiplex chips to allow selection of one of four inputs. The multiplexed address output signals (MA[1:0]) can be used as multiplexed address output bits or as general-purpose I/O. MA[1:0] are used as the address inputs for one to two dual 4-channel multiplexer chips. Since the MA[1:0] pins are digital outputs in the multiplexed mode, the software programmed input/output direction for the multiplexed address pins in the data direction register is superseded. Technical Data 408 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Memory Map 18.6.5 Multiplexed Analog Input Pins In the external multiplexed mode, four of the port QB pins are redefined to each represent four input channels. See Table 18-1. Table 18-1. Multiplexed Analog Input Channels Freescale Semiconductor, Inc... Multiplexed Analog Input Channels ANw Even numbered channels from 0 to 6 ANx Odd numbered channels from 1 to 7 ANy Even channels from 16 to 22 ANz Odd channels from 17 to 23 18.6.6 Voltage Reference Pins VRH and VRL are the dedicated input pins for the high and low reference voltages. Separating the reference inputs from the power supply pins allows for additional external filtering, which increases reference voltage precision and stability, and subsequently contributes to a higher degree of conversion accuracy. 18.6.7 Dedicated Analog Supply Pins VDDA and VSSA pins supply power to the analog subsystems of the QADC module. Dedicated power is required to isolate the sensitive analog circuitry from the normal levels of noise present on the digital power supply. 18.7 Memory Map The QADC occupies 1 Kbyte, or 512 16-bit entries, of address space. Ten 16-bit registers are control, port, and status registers, 64 16-bit entries are the CCW table, and 64 16-bit entries are the result table which occupies 192 16-bit address locations because the result data is readable in three data alignment formats. Table 18-2 is the QADC memory map. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 409 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Table 18-2. QADC Memory Map Address LSB Access (1) 0x00ca_0000 QADC module configuration register (QADCMCR) S 0x00ca_0002 QADC test register (QADCTEST)(2) S 0x00ca_0004 Reserved(3) -- 0x00ca_0006 Freescale Semiconductor, Inc... MSB Port QA data register (PORTQA) Port QB data register (PORTQB) S/U 0x00ca_0008 Port QA data direction register (DDRQA) S/U 0x00ca_000a QADC control register 0 (QACR0) S/U 0x00ca_000c QADC control register 1 (QACR1) S/U 0x00ca_000e QADC control register 2 (QACR2) S/U 0x00ca_0010 QADC status register 0 (QASR0) S/U 0x00ca_0012 QADC status register 1 (QASR1) S/U 0x00ca_0014- 0x00ca_01fe Reserved(3) -- 0x00ca_0200- 0x00ca_027e Conversion command word table (CCW) S/U 0x00ca_0280- 0x00ca_02fe Right justified, unsigned result register (RJURR) S/U 0x00ca_0300- 0x00ca_037e Left justified, signed result register (LJSRR) S/U 0x00ca_0380- 0x00ca_03fe Left justified, unsigned result register (LJURR) S/U 1. S = CPU supervisor mode access only. S/U = CPU supervisor or user mode access. User mode accesses to supervisor only addresses have no effect and result in a cycle termination transfer error. 2. Access results in the module generating an access termination transfer error if not in test mode. 3. Read/writes have no effect and the access terminates with a transfer error exception. Technical Data 410 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Register Descriptions 18.8 Register Descriptions This subsection describes the QADC registers. 18.8.1 QADC Module Configuration Register Freescale Semiconductor, Inc... The QADCMCR contains fields and bits that control freeze and stop modes and determines the privilege level required to access most registers. Address: 0x00ca_0000 and 0x00ca_0001 Bit 15 14 13 12 11 10 9 Bit 8 QSTOP QDBG 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Read: Write: Reset: Read: SUPV Write: Reset: 1 = Writes have no effect and the access terminates without a transfer error exception. Figure 18-3. QADC Module Configuration Register (QADCMCR) QSTOP -- Stop Enable Bit 1 = Forces QADC to idle state 0 = QADC is not forced to idle state QDBG -- Debug Enable Bit 1 = Finish any conversion in progress, then freezes in debug mode 0 = Ignore request to enter debug mode and continue conversions SUPV -- Supervisor/Unrestricted Data Space Bit 1 = Only supervisor mode access allowed; user mode accesses have no effect and result in a cycle termination transfer error 0 = Supervisor and user mode accesses allowed MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 411 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) 18.8.2 QADC Test Register QADCTEST is used only during factory testing of the MCU. Attempts to access this register outside of factory test mode will result in access privilege violation. Address: 0x00ca_0002 and 0x00ca_0003 Bit 15 14 13 12 11 10 9 Bit 8 Read: Freescale Semiconductor, Inc... Access results in the module generating an access termination transfer error if not in test mode. Write: Bit 7 6 5 4 3 2 1 Bit 0 Read: Access results in the module generating an access termination transfer error if not in test mode. Write: Figure 18-4. QADC Test Register (QADCTEST) 18.8.3 Port Data Registers QADC ports A and B are accessed through two 8-bit port data registers (PORTQA and PORTQB). Port QA pins are referred to as PQA[4:3, 1:0] when used as a bidirectional, 4-bit, input/output port that may be used for general-purpose digital input signals or digital output signals. Port QA can also be used for analog inputs (AN[56:55, 53:52]), external trigger inputs (ETRIG[2:1]), and external multiplexer address outputs (MA[1:0]). Port QB pins are referred to as PQB[3:0] when used as an input-only, 4-bit, digital port that may be used for general-purpose digital input signals. Data for PQB[3:0] is accessed from PORTQB. Port QB can also be used for non-multiplexed (AN[3:0]) and multiplexed (ANz, ANy, ANx, ANw) analog inputs. PORTQA and PORTQB are not initialized by reset. Technical Data 412 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Register Descriptions Address: 0x00ca_0006 Read: Bit 7 6 5 0 0 0 4 3 PQA4 PQA3 P P 2 1 Bit 0 PQA1 PQA0 P P 0 Write: Reset: 0 0 0 0 = Writes have no effect and the access terminates without a transfer error exception. Freescale Semiconductor, Inc... P = Current pin state if DDR is input, otherwise undefined Analog Channel: Muxed Address Outputs: External Trigger Inputs: AN56 AN55 ETRIG2 ETRIG1 AN53 MA1 AN52 MA0 Figure 18-5. QADC Port QA Data Register (PORTQA) Address: 0x00ca_0007 Read: Bit 7 6 5 4 0 0 0 0 3 2 1 Bit 0 PQB3 PQB2 PQB1 PQB0 P P P P Write: Reset: 0 0 0 0 = Writes have no effect and the access terminates without a transfer error exception. P = Current pin state if DDR is input, otherwise undefined Analog Channel: Muxed Analog Inputs: AN3 AN2 AN2 ANy AN1 ANx AN0 ANw Figure 18-6. QADC Port QB Data Register (PORTQB) Read: Anytime Write: Anytime except stop mode MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 413 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) 18.8.4 Port QA Data Direction Register Freescale Semiconductor, Inc... The port data direction register (DDRQA) is associated with the port QA digital I/O pins. The bidirectional pins may have somewhat higher leakage and capacitance specifications. Any bit in this register set to 1 configures the corresponding pin as an output. Any bit in this register cleared to 0 configures the corresponding pin as an input. The software is responsible for ensuring that DDR bits are not set to 1 on pins used for analog inputs. When the DDR bit is set to 1 and the pin is selected for analog conversion, the voltage sampled is that of the output digital driver as influenced by the load. When the MUX (externally multiplexed) bit is set in QACR0, the data direction register settings are ignored for the bits corresponding to PQA[1:0], the two multiplexed address (MA[1:0]) output pins. The MA[1:0] pins are forced to be digital outputs, regardless of the data direction setting, and the multiplexed address outputs are driven. The data returned during a port data register read is the value of MA[1:0], regardless of the data direction setting. Similarly, when the external trigger pins are assigned to port pins and external trigger queue operating mode is selected, the data direction setting for the corresponding pins, PQA3 or PQA4, is ignored. The port pins are forced to be digital inputs for ETRIG1 and/or ETRIG2. The data driven during a port data register read is the actual value of the pin, regardless of the data direction setting. NOTE: Use caution when mixing digital and analog inputs. They should be isolated as much as possible. Rise and fall times should be as large as possible to minimize ac coupling effects. Since port QB is input-only, a data direction register is not needed. Therefore, the lower byte of the port data direction register is not implemented. Technical Data 414 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Register Descriptions Address: 0x00ca_0008 and 0x00ca_0009 Read: Bit 15 14 13 0 0 0 12 11 DDQA4 DDQA3 10 9 Bit 8 DDQA1 DDQA0 0 Write: Reset: Read: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Freescale Semiconductor, Inc... Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 18-7. QADC Port QA Data Direction Register (DDRQA) Read: Anytime Write: Anytime except stop mode MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 415 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) 18.8.5 Control Registers This subsection describes the QADC control registers. 18.8.5.1 Control Register 0 Freescale Semiconductor, Inc... Control register 0 (QACR0) establishes the QCLK with prescaler parameter fields and defines whether external multiplexing is enabled. They are typically written once when the software initializes the QADC and not changed afterward. Address: 0x00ca_000a and 0x00ca_000b Bit 15 Read: 14 13 0 0 MUX 12 11 10 9 0 0 0 Bit 8 TRG PSH8 Write: Reset: 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 PSH7 PSH6 PSH5 PSH4 PSA PSL2 PSL1 PSL0 0 0 1 1 0 1 1 1 Read: Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 18-8. QADC Control Register 0 (QACR0) Read: Anytime Write: Anytime except stop mode MUX -- Externally Multiplexed Mode Bit The MUX bit allows the software to select the externally multiplexed mode, which affects the interpretation of the channel numbers and forces the MA[1:0] pins to be outputs. 1 = Externally multiplexed, 18 possible channels 0 = Internally multiplexed, eight possible channels Technical Data 416 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Register Descriptions TRG -- Trigger Assignment Bit The TRG bit allows the software to assign the ETRIG[2:1] pins to queue 1 and queue 2. 1 = ETRIG1 triggers queue 2, ETRIG2 triggers queue 1 0 = ETRIG1 triggers queue 1, ETRIG2 triggers queue 2 PSH[8:4] -- Prescaler Clock High Time Field Freescale Semiconductor, Inc... The PSH field selects the QCLK high time in the prescaler. See Section 22. Electrical Specifications for operating clock frequency (fQCLK) values. To keep the QCLK within the specified range, the PSH field selects the high time of the QCLK, which can range from 1 to 32 system clock cycles. The minimum high time for the QCLK is specified as tPSH. Table 18-3 displays the bits in PSH field which enable a range of QCLK high times. Table 18-3. Prescaler Clock High Times PSH[8:4] QCLK High Time PSH[8:4] QCLK High Time 00000 1 system clock cycle 10000 17 system clock cycles 00001 2 system clock cycles 10001 18 system clock cycles 00010 3 system clock cycles 10010 19 system clock cycles 00011 4 system clock cycles 10011 20 system clock cycles 00100 5 system clock cycles 10100 21 system clock cycles 00101 6 system clock cycles 10101 22 system clock cycles 00110 7 system clock cycles 10110 23 system clock cycles 00111 8 system clock cycles 10111 24 system clock cycles 01000 9 system clock cycles 11000 25 system clock cycles 01001 10 system clock cycles 11001 26 system clock cycles 01010 11 system clock cycles 11010 27 system clock cycles 01011 12 system clock cycles 11011 28 system clock cycles 01100 13 system clock cycles 11100 29 system clock cycles 01101 14 system clock cycles 11101 30 system clock cycles 01110 15 system clock cycles 11110 31 system clock cycles 01111 16 system clock cycles 11111 32 system clock cycles MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 417 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) PSA -- Prescaler Add Clock Tick Bit PSA is maintained for software compatibility but has no functional benefit to this version of the module. PSL[2:0] -- Prescaler Clock Low Time Field The PSL field selects the QCLK low time in the prescaler. See Section 22. Electrical Specifications for f QCLK values. Freescale Semiconductor, Inc... To keep the QCLK within the specified range, the PSL field selects the low time of the QCLK, which can range from one to eight system clock cycles. The minimum low time for the clock is specified as tPSL. Table 18-4 displays the bits in PSL field which enable a range of QCLK low times. Table 18-4. Prescaler Clock Low Times PSL[2:0] QCLK Low Time 000 1 system clock cycle 001 2 system clock cycles 010 3 system clock cycles 011 4 system clock cycles 100 5 system clock cycles 101 6 system clock cycles 110 7 system clock cycles 111 8 system clock cycles Technical Data 418 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Register Descriptions 18.8.5.2 Control Register 1 Control register 1 (QACR1) is the mode control register for the operation of queue 1. The applications software defines the queue operating mode for the queue and may enable a completion and/or pause interrupt. Most of the bits are typically written once when the software initializes the QADC and not changed afterward. Stop mode resets the register ($0000) Freescale Semiconductor, Inc... Address: 0x00ca_000c and 0x00ca_000d Bit 15 14 12 11 10 9 Bit 8 CIE1 PIE1 MQ112 MQ111 MQ110 MQ19 MQ18 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Read: Write: Reset: Read: 13 0 SSE1 Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 18-9. QADC Control Register 1 (QACR1) Read: Anytime Write: Anytime except stop mode CIE1 -- Queue 1 Completion Interrupt Enable Bit CIE1 enables an interrupt upon completion of queue 1. The interrupt request is initiated when the conversion is complete for the CCW in queue 1. 1 = Enable interrupt after the conversion of the sample requested by the last CCW in queue 1 0 = Disable queue 1 completion interrupt MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 419 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) PIE1 -- Queue 1 Pause Interrupt Enable Bit PIE1 enables an interrupt when queue 1 enters the pause state. The interrupt request is initiated when conversion is complete for a CCW that has the pause bit set. 1 = Enable an interrupt after an end-of-conversion for queue 1 which has the pause bit set. 0 = Disable the pause interrupt associated with queue 1. SSE1 -- Queue 1 Single-Scan Enable Bit Freescale Semiconductor, Inc... SSE1 enables a single-scan of queue 1 to start after a trigger event occurs. The SSE1 bit may be set to a 1 during the same write cycle when the MQ1 bits are set for one of the single-scan queue operating modes. The single-scan enable bit can be written as a 1 or a 0, but is always read as a 0, unless a test mode is selected. The SSE1 bit enables a trigger event to initiate queue execution for any single-scan operation on queue 1.The QADC clears the SSE1 bit when the single-scan is complete. 1 = Accept a trigger event to start queue 1 in a single-scan mode. 0 = Trigger events are not accepted for single-scan modes. MQ1[12:8] -- Queue 1 Operating Mode Field The MQ1 field selects the queue operating mode for queue 1. Table 18-5 shows the bits in the MQ1 field which enable different queue 1 operating modes. Table 18-5. Queue 1 Operating Modes MQ1[12:8] Operating Mode 00000 Disabled mode, conversions do not occur 00001 Software-triggered single-scan mode (started with SSE1) 00010 External-trigger rising-edge single-scan mode 00011 External-trigger falling-edge single-scan mode 00100 Interval timer single-scan mode: time = QCLK period x 27 00101 Interval timer single-scan mode: time = QCLK period x 28 00110 Interval timer single-scan mode: time = QCLK period x 29 00111 Interval timer single-scan mode: time = QCLK period x 210 01000 Interval timer single-scan mode: time = QCLK period x 211 Technical Data 420 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Register Descriptions Table 18-5. Queue 1 Operating Modes (Continued) Freescale Semiconductor, Inc... MQ1[12:8] Operating Mode 01001 Interval timer single-scan mode: time = QCLK period x 212 01010 Interval timer single-scan mode: time = QCLK period x 213 01011 Interval timer single-scan mode: time = QCLK period x 214 01100 Interval timer single-scan mode: time = QCLK period x 215 01101 Interval timer single-scan mode: time = QCLK period x 216 01110 Interval timer single-scan mode: time = QCLK period x 217 01111 Externally gated single-scan mode (started with SSE1) 10000 Reserved mode 10001 Software-triggered continuous-scan mode 10010 External-trigger rising-edge continuous-scan mode 10011 External-trigger falling-edge continuous-scan mode 10100 Periodic timer continuous-scan mode: time = QCLK period x 27 10101 Periodic timer continuous-scan mode: time = QCLK period x 28 10110 Periodic timer continuous-scan mode: time = QCLK period x 29 10111 Periodic timer continuous-scan mode: time = QCLK period x 210 11000 Periodic timer continuous-scan mode: time = QCLK period x 211 11001 Periodic timer continuous-scan mode: time = QCLK period x 212 11010 Periodic timer continuous-scan mode: time = QCLK period x 213 11011 Periodic timer continuous-scan mode: time = QCLK period x 214 11100 Periodic timer continuous-scan mode: time = QCLK period x 215 11101 Periodic timer continuous-scan mode: time = QCLK period x 216 11110 Periodic timer continuous-scan mode: time = QCLK period x 217 11111 Externally gated continuous-scan mode MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 421 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) 18.8.5.3 QADC Control Register 2 Control register 2 (QACR2) is the mode control register for the operation of queue 2. Software specifies the queue operating mode of queue 2 and may enable a completion and/or a pause interrupt. Most of the bits are typically written once when the software initializes the QADC and not changed afterward. Stop mode resets the register ($007f) Freescale Semiconductor, Inc... Address: 0x00ca_000e and 0x00ca_000f Bit 15 14 CIE2 PIE2 Read: 12 11 10 9 Bit 8 MQ212 MQ211 MQ210 MQ29 MQ28 0 Write: Reset: 13 SSE2 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 RESUME BQ26 BQ25 BQ24 BQ23 BQ22 BQ21 BQ20 0 1 1 1 1 1 1 1 Read: Write: Reset: Figure 18-10. QADC Control Register 2 (QACR2) Read: Anytime Write: Anytime except stop mode CIE2 -- Queue 2 Completion Software Interrupt Enable Bit CIE2 enables an interrupt upon completion of queue 2. The interrupt request is initiated when the conversion is complete for the CCW in queue 2. 1 = Enable an interrupt after an end-of-conversion for queue 2. 0 = Disable the queue completion interrupt associated with queue 2. Technical Data 422 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Register Descriptions PIE2 -- Queue 2 Pause Software Interrupt Enable Bit PIE2 enables an interrupt when queue 2 enters the pause state. The interrupt request is initiated when conversion is complete for a CCW that has the pause bit set. 1 = Enable an interrupt after an end-of-conversion for queue 2 which has the pause bit set. 0 = Disable the pause interrupt associated with queue 2. SSE2 -- Queue 2 Single-Scan Enable Bit Freescale Semiconductor, Inc... SSE2 enables a single-scan of queue 2 to start after a trigger event occurs. The SSE2 bit may be set to a 1 during the same write cycle when the MQ2 bits are set for one of the single-scan queue operating modes. The single-scan enable bit can be written as a 1 or a 0, but is always read as a 0, unless a test mode is selected. The SSE2 bit enables a trigger event to initiate queue execution for any single-scan operation on queue 2. The QADC clears the SSE2 bit when the single-scan is complete. 1 = Accept a trigger event to start queue 2 in a single-scan mode. 0 = Trigger events are not accepted for single-scan modes. MQ2[12:8] -- Queue 2 Operating Mode Field The MQ2 field selects the queue operating mode for queue 2. Table 18-6 shows the bits in the MQ2 field which enable different queue 2 operating modes. Table 18-6. Queue 2 Operating Modes MQ2[12:8] Operating Modes 00000 Disabled mode, conversions do not occur 00001 Software triggered single-scan mode (started with SSE2) 00010 External trigger rising edge single-scan mode 00011 External trigger falling edge single-scan mode 00100 Interval timer single-scan mode: time = QCLK period x 27 00101 Interval timer single-scan mode: time = QCLK period x 28 00110 Interval timer single-scan mode: time = QCLK period x 29 00111 Interval timer single-scan mode: time = QCLK period x 210 01000 Interval timer single-scan mode: time = QCLK period x 211 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 423 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Table 18-6. Queue 2 Operating Modes (Continued) Freescale Semiconductor, Inc... MQ2[12:8] Operating Modes 01001 Interval timer single-scan mode: time = QCLK period x 212 01010 Interval timer single-scan mode: time = QCLK period x 213 01011 Interval timer single-scan mode: time = QCLK period x 214 01100 Interval timer single-scan mode: time = QCLK period x 215 01101 Interval timer single-scan mode: time = QCLK period x 216 01110 Interval timer single-scan mode: time = QCLK period x 217 01111 Reserved mode 10000 Reserved mode 10001 Software triggered continuous-scan mode 10010 External trigger rising edge continuous-scan mode 10011 External trigger falling edge continuous-scan mode 10100 Periodic timer continuous-scan mode: time = QCLK period x 27 10101 Periodic timer continuous-scan mode: time = QCLK period x 28 10110 Periodic timer continuous-scan mode: time = QCLK period x 29 10111 Periodic timer continuous-scan mode: time = QCLK period x 210 11000 Periodic timer continuous-scan mode: time = QCLK period x 211 11001 Periodic timer continuous-scan mode: time = QCLK period x 212 11010 Periodic timer continuous-scan mode: time = QCLK period x 213 11011 Periodic timer continuous-scan mode: time = QCLK period x 214 11100 Periodic timer continuous-scan mode: time = QCLK period x 215 11101 Periodic timer continuous-scan mode: time = QCLK period x 216 11110 Periodic timer continuous-scan mode: time = QCLK period x 217 11111 Reserved mode Technical Data 424 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Register Descriptions RESUME -- Queue 2 Resume Bit RESUME selects the queue 2 resumption point after suspension due to queue 1. If RESUME is changed during the execution of queue 2, the change is not recognized until an end-of-queue condition is reached or the queue operating mode of queue 2 is changed. The primary reason for selecting re-execution of the entire queue or subqueue is to guarantee that all samples are taken consecutively in one scan (coherency). Freescale Semiconductor, Inc... When subqueues are not used, queue 2 execution restarts after suspension with the first CCW in queue 2. When a pause has previously occurred in queue 2 execution, queue execution restarts after suspension with the first CCW in the current subqueue. A subqueue is considered to be a stand-alone sequence of conversions. Once a pause flag has been set to report subqueue completion, that subqueue is not repeated until all CCWs in queue 2 are executed. An example of using the RESUME bit is when the frequency of queue 1 trigger events prohibit queue 2 completion. If the rate of queue 1 execution is too high, it is best for queue 2 execution to continue with the CCW that was being converted when queue 2 was suspended. This allows queue 2 to eventually complete execution. 1 = After suspension, begin execution with the aborted CCW in queue 2. 0 = After suspension, begin execution with the first CCW of queue 2 or the current subqueue of queue 2. BQ2[6:0] -- Beginning of Queue 2 Field BQ2[6:0] indicates the CCW location where queue 2 begins. To allow the length of queue 1 and queue 2 to vary, a programmable pointer identifies the CCW table location where queue 2 begins. The BQ2 field also serves as an end-of-queue condition for queue 1. Setting BQ2[6:0] beyond physical CCW table memory space allows queue 1 all 64 entries. Software defines the beginning of queue 2 by programming the BQ2 field in QACR2. BQ2 is usually programmed before or at the same time as the queue operating mode for queue 2 is selected. If BQ2 is 64 or greater, queue 2 has no entries, the entire CCW table is dedicated to queue 1 and CCW63 is the end-of-queue 1. If BQ2[6:0] is 0, the entire CCW table is dedicated to queue 2. As a special case, MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 425 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) when a queue operating mode for queue 1 is selected and a trigger event occurs for queue 1 with BQ2 set to 0, queue 1 execution is terminated after CCW0 is read. Conversions do not occur. Freescale Semiconductor, Inc... The BQ2[6:0] pointer may be changed dynamically, to alternate between queue 2 scan sequences. A change in BQ2[6:0] after queue 2 has begun or if queue 2 has a trigger pending does not affect queue 2 until queue 2 is started again. For example, two scan sequences could be defined as follows: The first sequence starts at CCW10, with a pause after CCW11 and an EOQ programmed in CCW15; the second sequence starts at CCW16, with a pause after CCW17 and an EOQ programmed in CCW39. With BQ2[6:0] set to CCW10 and the continuous-scan mode selected, queue execution begins. When the pause is encountered in CCW11, a software interrupt routine can redefine BQ2[6:0] to be CCW16. Therefore, after the end-of-queue is recognized in CCW15, an internal retrigger event is generated and execution restarts at CCW16. When the pause software interrupt occurs again, software can change BQ2 back to CCW10. After the end-of-queue is recognized in CCW39, an internal retrigger event is created and execution now restarts at CCW10. If BQ2[6:0] is changed while queue 1 is active, the effect of BQ2[6:0] as an end-of-queue indication for queue 1 is immediate. However, beware of the risk of losing the end-of-queue 1 when changing BQ2[6:0]. Using EOQ (chan63) to end queue 1 is recommended. NOTE: If BQ2[6:0] was assigned to the CCW that queue 1 is currently working on, then that conversion is completed before BQ2[6:0] takes effect. Each time a CCW is read for queue 1, the CCW location is compared with the current value of the BQ2[6:0] pointer to detect a possible end-of-queue condition. For example, if BQ2[6:0] is changed to CCW3 while queue 1 is converting CCW2, queue 1 is terminated after the conversion is completed. However, if BQ2[6:0] is changed to CCW1 while queue 1 is converting CCW2, the QADC would not recognize a BQ2[6:0] end-of-queue condition until queue 1 execution reached CCW1 again, presumably on the next pass through the queue. Technical Data 426 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Register Descriptions 18.8.6 Status Registers This subsection describes the QADC status registers. 18.8.6.1 QADC Status Register 0 The QADC status register 0 (QASR0) contains information about the state of each queue and the current A/D conversion. Freescale Semiconductor, Inc... Stop mode resets the register ($0000) Address: 0x00ca_0010 and 0x00ca_0011 Bit 15 14 13 12 11 10 9 Bit 8 CF1 PF1 CF2 PF2 TOR1 TOR2 QS9 QS8 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 QS7 QS6 CWP5 CWP4 CWP3 CWP2 CWP1 CWP0 0 0 0 0 0 0 0 0 Read: Write: Reset: Read: Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 18-11. QADC Status Register 0 (QASR0) Read: Anytime Write: For flag bits (CF1, PF1, CF2, PF2, TOR1, TOR2): Writing a 1 has no effect, write a 0 to clear. For QA[9:6] and CWP: Write has no effect. Never in stop mode CF1 -- Queue 1 Completion Flag CF1 indicates that a queue 1 scan has been completed. The scan completion flag is set by the QADC when the input channel sample requested by the last CCW in queue 1 is converted, and the result is stored in the result table. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 427 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) The end-of-queue 1 is identified when execution is complete on the CCW in the location prior to that pointed to by BQ2, when the current CCW contains an end-of-queue code instead of a valid channel number, or when the currently completed CCW is in the last location of the CCW RAM. Freescale Semiconductor, Inc... When CF1 is set and interrupts are enabled for that queue completion flag, the QADC asserts an interrupt request. The software reads the completion flag during an interrupt service routine to identify the interrupt request. The interrupt request is cleared when the software writes a 0 to the completion flag bit, when the bit was previously read as a 1. Once set, only software or reset can clear CF1. CF1 is maintained by the QADC regardless of whether the corresponding interrupt is enabled. The software polls for CF1 bit to see if it is set. This allows the software to recognize that the QADC is finished with a queue 1 scan. The software acknowledges that it has detected the completion flag being set by writing a 0 to the completion flag after the bit was read as a 1. PF1 -- Queue 1 Pause Flag PF1 indicates that a queue 1 scan has reached a pause. PF1 is set by the QADC when the current queue 1 CCW has the pause bit set, the selected input channel has been converted, and the result has been stored in the result table. Once PF1 is set, the queue enters the paused state and waits for a trigger event to allow queue execution to continue. However, if the CCW with the pause bit set is the last CCW in a queue, the queue execution is complete. The queue status becomes idle, not paused, and both the pause and completion flags are set. Another exception occurs in software controlled mode, where the PF1 can be set but queue 1 never enters the pause state since queue 1 continues without pausing. When PF1 is set and interrupts are enabled for the corresponding queue, the QADC asserts an interrupt request. The software may read PF1 during an interrupt service routine to identify the interrupt request. The interrupt request is cleared when the software writes a 0 to PF1, when the bit was previously read as a 1. Once set, only software or reset can clear PF1. Technical Data 428 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Register Descriptions In external gated single-scan and continuous-scan mode, the definition of PF1 has been redefined. When the gate closes before the end-of-queue 1 is reached, PF1 becomes set to indicate that an incomplete scan has occurred. In single-scan mode, setting PF1 can be used to cause an interrupt and software can then determine if queue 1 should be enabled again. In either external gated mode, setting PF1 indicates that the results for queue 1 have not been collected during one scan (coherently). Freescale Semiconductor, Inc... NOTE: If a pause in a CCW is encountered in external gated mode for either single-scan and continuous-scan mode, the pause flag will not set, and execution continues without pausing. This has allowed for the added definition of PF1 in the external gated modes. PF1 is maintained by the QADC regardless of whether the corresponding interrupts are enabled. The software may poll PF1 to find out when the QADC has reached a pause in scanning a queue.The software acknowledges that it has detected a pause flag being set by writing a 0 to PF1 after the bit was last read as a 1. 1 = Queue 1 has reached a pause or gate closed before end-of-queue in gated mode. 0 = Queue 1 has not reached a pause or gate has not closed before end-of-queue in gated mode. See Table 18-7 for a summary of pause response in all scan modes. Table 18-7. Pause Response Scan Mode Queue Operation PF Asserts? External trigger single-scan Pauses Yes External trigger continuous-scan Pauses Yes Interval timer trigger single-scan Pauses Yes Interval timer continuous-scan Pauses Yes Software-initiated single-scan Continues Yes Software-initiated continuous-scan Continues Yes External gated single-scan Continues No External gated continuous-scan Continues No MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 429 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) CF2 -- Queue 2 Completion Flag CF2 indicates that a queue 2 scan has been completed. CF2 is set by the QADC when the input channel sample requested by the last CCW in queue 2 is converted, and the result is stored in the result table. The end-of-queue 2 is identified when the current CCW contains an end-of-queue code instead of a valid channel number or when the currently completed CCW is in the last location of the CCW RAM. Freescale Semiconductor, Inc... When CF2 is set and interrupts are enabled for that queue completion flag, the QADC asserts an interrupt request. The software reads CF2 during an interrupt service routine to identify the interrupt request. The interrupt request is cleared when the software writes a 0 to the CF2 bit, when the bit was previously read as a 1. Once set, only software or reset can clear CF2. CF2 is maintained by the QADC regardless of whether the corresponding interrupts are enabled. The software polls for CF2 to see if it is set. This allows the software to recognize that the QADC is finished with a queue 2 scan. The software acknowledges that it has detected the completion flag being set by writing a 0 to the completion flag after the bit was read as a 1. PF2 -- Queue 2 Pause Flag PF2 indicates that a queue 2 scan has reached a pause. PF2 is set by the QADC when the current queue 2 CCW has the pause bit set, the selected input channel has been converted, and the result has been stored in the result table. Once PF2 is set, the queue enters the paused state and waits for a trigger event to allow queue execution to continue. However, if the CCW with the pause bit set is the last CCW in a queue, the queue execution is complete. The queue status becomes idle, not paused, and both the pause and completion flags are set. Another exception occurs in software controlled mode, where the PF2 can be set but queue 2 never enters the pause state. When PF2 is set and interrupts are enabled for the corresponding queue, the QADC asserts an interrupt request. The software reads PF2 during an interrupt service routine to identify the interrupt request. The interrupt request is cleared when the software writes a 0 to PF2, when the bit was previously read as a 1. Once set, only software or reset can clear PF2. Technical Data 430 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Register Descriptions PF2 is maintained by the QADC regardless of whether the corresponding interrupts are enabled. The software may poll PF2 to find out when the QADC has reached a pause in scanning a queue. The software acknowledges that it has detected a pause flag being set by writing a 0 to PF2 after the bit was last read as a 1. 1 = queue 2 has reached a pause. 0 = queue 2 has not reached a pause. See Table 18-7 for a summary of pause response in all scan modes. TOR1 -- Queue 1 Trigger Overrun Freescale Semiconductor, Inc... TOR1 indicates that an unexpected trigger event has occurred for queue 1. TOR1 can be set only while queue 1 is in the active state. A trigger event generated by a transition on the external trigger pin or by the periodic/interval timer may be captured as a trigger overrun. TOR1 cannot occur when the software-initiated single-scan mode or the software-initiated continuous-scan mode are selected. TOR1 occurs when a trigger event is received while a queue is executing and before the scan has completed or paused. TOR1 has no effect on the queue execution. After a trigger event has occurred for queue 1, and before the scan has completed or paused, additional queue 1 trigger events are not retained. Such trigger events are considered unexpected, and the QADC sets the TOR1 error status bit. An unexpected trigger event may be a system overrun situation, indicating a system loading mismatch. In external gated continuous-scan mode, the definition of TOR1 has been redefined. In the case when queue 1 reaches an end-of-queue condition for the second time during an open gate, TOR1 becomes set. This is considered an overrun condition. In this case CF1 has been set for the first end-of-queue 1 condition and then TOR1 becomes set for the second end-of-queue 1 condition. For TOR1 to be set, software must not clear CF1 before the second end-of-queue 1. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 431 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) The software acknowledges that it has detected a trigger overrun being set by writing a 0 to the trigger overrun, after the bit was read as a 1. Once set, only software or reset can clear TOR1. 1 = At least one unexpected queue 1 trigger event has occurred or queue 1 reaches an end-of-queue condition for the second time in gated mode 0 = No unexpected queue 1 trigger events have occurred TOR2 -- Queue 2 Trigger Overrun Flag Freescale Semiconductor, Inc... TOR2 indicates that an unexpected trigger event has occurred for queue 2. TOR2 can be set when queue 2 is in the active, suspended, and trigger pending states. The TOR2 trigger overrun can occur only when using an external trigger mode or a periodic/interval timer mode. Trigger overruns cannot occur when the software-initiated single-scan mode and the software-initiated continuous-scan mode are selected. TOR2 occurs when a trigger event is received while queue 2 is executing, suspended, or a trigger is pending. TOR2 has no effect on the queue execution. A trigger event that causes a trigger overrun is not retained since it is considered unexpected. An unexpected trigger event may be a system overrun situation, indicating a system loading mismatch. The software acknowledges that it has detected a trigger overrun being set by writing a 0 to the trigger overrun, after the bit was read as a 1. Once set, only software or reset can clear TOR2. 1 = At least one unexpected queue 2 trigger event has occurred. 0 = No unexpected queue 2 trigger events have occurred. QS[9:6] -- Queue Status Field The 4-bit read-only QS field indicates the current condition of queue 1 and queue 2. There are five queue status conditions: - Idle - Active - Paused - Suspended - Trigger pending Technical Data 432 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Register Descriptions The two most significant bits are associated primarily with queue 1, and the remaining two bits are associated with queue 2. Since the priority scheme between the two queues causes the status to be interlinked, the status bits are considered as one 4-bit field. Table 18-8 shows the bits in the QS field and how they affect the status of queue 1 and queue 2. One or both queues may be in the idle state. When a queue is idle, CCWs are not being executed for that queue, the queue is not in the pause state, and there is not a trigger pending. Freescale Semiconductor, Inc... The idle state occurs when a queue is disabled, when a queue is in a reserved mode, or when a queue is in a valid queue operating mode awaiting a trigger event to initiate queue execution. Table 18-8. Queue Status QS[9:6] Queue 1/Queue 2 States 0000 Queue 1 idle, queue 2 idle 0001 Queue 1 idle, queue 2 paused 0010 Queue 1 idle, queue 2 active 0011 Queue 1 idle, queue 2 trigger pending 0100 Queue 1 paused, queue 2 idle 0101 Queue 1 paused, queue 2 paused 0110 Queue 1 paused, queue 2 active 0111 Queue 1 paused, queue 2 trigger pending 1000 Queue 1 active, queue 2 idle 1001 Queue 1 active, queue 2 paused 1010 Queue 1 active, queue 2 suspended 1011 Queue 1 active, queue 2 trigger pending 1100 Reserved 1101 Reserved 1110 Reserved 1111 Reserved A queue is in the active state when a valid queue operating mode is selected, when the selected trigger event has occurred, or when the QADC is performing a conversion specified by a CCW from that queue. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 433 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Only one queue can be active at a time. Either or both queues can be in the paused state. A queue is paused when the previous CCW executed from that queue had the pause bit set. The QADC does not execute any CCWs from the paused queue until a trigger event occurs. Consequently, the QADC can service queue 2 while queue 1 is paused. Freescale Semiconductor, Inc... Only queue 2 can be in the suspended state. When a trigger event occurs on queue 1 while queue 2 is executing, the current queue 2 conversion is aborted. The queue 2 status is reported as suspended. Queue 2 transitions back to the active state when queue 1 becomes idle or paused. A trigger pending state is required since both queues cannot be active at the same time. The status of queue 2 is changed to trigger pending when a trigger event occurs for queue 2 while queue 1 is active. In the opposite case, when a trigger event occurs for queue 1 while queue 2 is active, queue 2 is aborted and the status is reported as queue 1 active, queue 2 suspended. So due to the priority scheme, only queue 2 can be in the trigger pending state. Two transition cases cause the queue 2 status to be trigger pending before queue 2 is shown to be in the active state. When queue 1 is active and there is a trigger pending on queue 2, after queue 1 completes or pauses, queue 2 continues to be in the trigger pending state for a few clock cycles. The fleeting status conditions are: * queue 1 idle with queue 2 trigger pending * queue 1 paused with queue 2 trigger pending Figure 18-12 displays the status conditions of the queue status field as the QADC goes through the transition from queue 1 active to queue 2 active. The queue status field is affected by the stop mode. Since all of the analog logic and control registers are reset, the queue status field is reset to queue 1 idle, queue 2 idle. During the debug mode, the queue status field is not modified. The queue status field retains the status it held prior to freezing. As a result, the queue status can show queue 1 active, queue 2 idle, even though neither queue is being executed during freeze. Technical Data 434 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Queued Analog-to-Digital Converter (QADC) Register Descriptions QUEUE 1 QUEUE 2 ACTIVE IDLE ACTIVE TRIGGER PENDING IDLE (PAUSED) TRIGGER PENDING IDLE (PAUSED) ACTIVE Figure 18-12. Queue Status Transition CWP[5:0] -- Command Word Pointer Field The CWP allows the software to know which CCW is executing at present, or was last completed. The command word pointer is a software read-only field, and write operations have no effect. The CWP allows software to monitor the progress of the QADC scan sequence. The CWP field is a CCW word pointer with a valid range of 0 to 63. When a queue enters the paused state, the CWP points to the CCW with the pause bit set. While in pause, the CWP value is maintained until a trigger event occurs on the same queue or the other queue. Usually, the CWP is updated a few clock cycles before the queue status field shows that the queue has become active. For example, software may read a CWP pointing to a CCW in queue 2, and the status field shows queue 1 paused, queue 2 trigger pending. When the QADC finishes the scan of the queue, the CWP points to the CCW where the end-of-queue condition was detected. Therefore, when the end-of-queue condition is a CCW with the EOQ code (channel 63), the CWP points to the CCW containing the EOQ. When the last CCW in a queue is in the last CCW table location (CCW63), and it does not contain the EOQ code, the end-of-queue is detected when the following CCW is read, so the CWP points to word CCW0. Finally, when queue 1 operation is terminated after a CCW is read that is defined as BQ2, the CWP points to the same CCW as BQ2. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 435 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) During the stop mode, the CWP is reset to 0, since the control registers and the analog logic are reset. When the debug mode is entered, the CWP is unchanged; it points to the last executed CCW. 18.8.6.2 QADC Status Register 1 Stop mode resets the register ($3f3f) Freescale Semiconductor, Inc... Address: 0x00ca_0012 and 0x00ca_0013 Read: Bit 15 14 13 12 11 10 9 Bit 8 0 0 CWPQ15 CWPQ14 CWPQ13 CWPQ12 CWPQ11 CWPQ10 0 0 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 0 0 CWPQ25 CWPQ24 CWPQ23 CWPQ22 CWPQ21 CWPQ20 0 0 1 1 1 1 1 1 Write: Reset: Read: Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 18-13. QADC Status Register 1 (QASR1) Read: Anytime Write: Never CWPQ1[5:0] -- Queue 1 Command Word Pointer Field CWPQ1[5:0] allows the software to know what CCW was last completed for queue 1. This field is a software read-only field, and write operations have no effect. CWPQ1 allows software to read the last executed CCW in queue 1, regardless of which queue is active. The CWPQ1[5:0] field is a CCW word pointer with a valid range of 0 to 63 (0x3f). In contrast to CWP, CPWQ1 is updated when the conversion result is written. When the QADC finishes a conversion in queue 1, both the result register is written and the CWPQ1 is updated. Finally, when queue 1 operation is terminated after a CCW is read that is defined as BQ2, CWP points to BQ2 while CWPQ1 points to the last CCW queue 1. Technical Data 436 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Register Descriptions During the stop mode, the CWPQ1 is reset to 63 (0x3f), since the control registers and the analog logic are reset. When the debug mode is entered, the CWPQ1 is unchanged; it points to the last executed CCW in queue 1. Freescale Semiconductor, Inc... CWPQ2[5:0] -- Queue 2 Command Word Pointer Field CWPQ2[5:0] allows the software to know what CCW was last completed for queue 2. This field is a software read-only field, and write operations have no effect. CWPQ2[5:0] allows software to read the last executed CCW in queue 2, regardless which queue is active. The CWPQ2[5:0] field is a CCW word pointer with a valid range of 0 to 63. In contrast to CWP, CPWQ2 is updated when the conversion result is written. When the QADC finishes a conversion in queue 2, both the result register is written and the CWPQ2 are updated. During the stop mode, the CWPQ2 is reset to 63, since the control registers and the analog logic are reset. When the debug mode is entered, the CWP is unchanged; it points to the last executed CCW in queue 2. 18.8.7 Conversion Command Word Table Address: 0x00ca_0200 through 0x00ca_027e Read: Bit 15 14 13 12 11 10 0 0 0 0 0 0 9 Bit 8 P BYP Write: Reset: 0 0 0 0 0 0 U U Bit 7 6 5 4 3 2 1 Bit 0 IST1 IST0 CHAN5 CHAN4 CHAN3 CHAN2 CHAN1 CHAN0 U U U U U U U U Read: Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. U = Unaffected Figure 18-14. Conversion Command Word Table (CCW) MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 437 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Read: Anytime except reads during stop mode are invalid Write: Anytime except stop mode P -- Pause Bit Freescale Semiconductor, Inc... The pause bit allows software to create subqueues within queue 1 and queue 2. The QADC performs the conversion specified by the CCW with the pause bit set, and then the queue enters the pause state. Another trigger event causes execution to continue from the pause to the next CCW. 1 = Enter pause state after execution of current CCW 0 = Do not enter pause state after execution of current CCW NOTE: The P bit does not cause the queue to pause in the software controlled modes or external gated modes. BYP -- Sample Amplifier Bypass Bit Setting the BYP field in the CCW enables the amplifier bypass mode for a conversion and subsequently changes the timing. The initial sample time is eliminated, reducing the potential conversion time by two QCLKs. However, due to internal RC effects, a minimum final sample time of four QCLKs must be allowed. When using this mode, the external circuit should be of low source impedance. Loading effects of the external circuitry need to be considered, since the benefits of the sample amplifier are not present. 1 = Amplifier bypass mode enabled 0 = Amplifier bypass mode disabled NOTE: BYP is maintained for software compatibility but has no functional benefit to this version of the module. IST[0:1] -- Input Sample Time Field The IST field allows software to specify the length of the sample window. Provision is made to vary the input sample time, through software control, to offer flexibility in the source impedance of the circuitry providing the QADC analog channel inputs. Longer sample times permit more accurate A/D conversions of signals with higher source impedances. Table 18-9 shows the four selectable input sample times. Technical Data 438 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Register Descriptions Table 18-9. Input Sample Times IST[0:1] Input Sample Times 00 Input sample time = QCLK period x 2 01 Input sample time = QCLK period x 4 10 Input sample time = QCLK period x 8 11 Input sample time = QCLK period x 16 Freescale Semiconductor, Inc... The programmable sample time can also be used to increase the time interval between conversions to adjust the queue execution time or the sampling rate. CHAN[5:0] -- Channel Number Field The CHAN field selects the input channel number. The software programs the channel field of the CCW with the channel number corresponding to the analog input pin to be sampled and converted. The analog input pin channel number assignments and the pin definitions vary depending on whether the multiplexed or non-multiplexed mode is used by the application. As far as the queue scanning operations are concerned, there is no distinction between an internally or externally multiplexed analog input. Table 18-10 shows the channel number assignments for the non-multiplexed mode. Table 18-11 shows the channel number assignments for the multiplexed mode. The channel field is programmed for channel 63 to indicate the end of the queue. Channels 60 to 62 are special internal channels. When one of the special channels is selected, the sampling amplifier is not used. The value of VRL, VRH, or (VRH-VRL)/2 is placed directly onto the converter. Also for the internal special channels, programming any input sample time other than two has no benefit except to lengthen the overall conversion time. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 439 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Table 18-10. Non-Multiplexed Channel Assignments and Pin Designations Channel Number(1) in CCW CHAN Field Freescale Semiconductor, Inc... Non-Multiplexed Input Pins Port Pin Name Analog Pin Name Other Functions Pin Type Binary Decimal PQB0 PQB1 PQB2 PQB3 AN0 AN1 AN2 AN3 -- -- -- -- Input Input Input Input 000000 000001 000010 000011 0 1 2 3 PQA0 PQA1 AN52 AN53 -- -- Input/output Input/output 110100 110101 52 53 PQA3 PQA4 AN55 AN56 ETRIG1 ETRIG2 Input/output Input/output 110111 111000 55 56 VRL -- Low reference High reference -- -- -- (VRH-VRL)/2 Input Input -- 111100 111101 111110 60 61 62 -- -- End-of-queue code -- 111111 63 VRH 1. All channels not listed are reserved or unimplemented and return undefined results. Table 18-11. Multiplexed Channel Assignments and Pin Designations Channel Number(1) in CCW CHAN Field Multiplexed Input Pins Port Pin Name Analog Pin Name Other Functions Pin Type Binary Decimal PQB0 PQB1 PQB2 PQB3 ANw ANx ANy ANz -- -- -- -- Input Input Input Input 000XX0 000XX1 010XX0 010XX1 0, 2, 4, 6 1, 3, 5, 7 16, 18, 20, 22 17, 19, 21, 23 PQA0 PQA1 -- -- MA0 MA1 Output Output 110100 110101 52 53 PQA3 PQA4 AN55 AN56 ETRIG1 ETRIG2 Input/output Input/output 110111 111000 55 56 VRL VRH -- Low reference High reference -- -- -- (VRH-VRL)/2 Input Input -- 111100 111101 111110 60 61 62 -- -- End-of-queue code -- 111111 63 1. All channels not listed are reserved or unimplemented and return undefined results. Technical Data 440 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Register Descriptions 18.8.8 Result Registers This subsection describes the result registers. 18.8.8.1 Right-Justified Unsigned Result Register Address: 0x00ca_0280 through 0x00ca_02fe Read: Bit 15 14 13 12 11 10 0 0 0 0 0 0 9 Bit 8 Freescale Semiconductor, Inc... RESULT Write: Reset: 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Read: RESULT Write: Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 18-15. Right-Justified Unsigned Result Register (RJURR) Read: Anytime except reads during stop mode are invalid Write: Anytime except stop mode RESULT[9:0] -- Result Field The conversion result is unsigned, right-justified data. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 441 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) 18.8.8.2 Left-Justified Signed Result Register Address: 0x00ca_0300 through 0x00ca_037e Bit 15 14 13 12 11 10 9 Bit 8 Read: Write: S RESULT Reset: Bit 7 6 Freescale Semiconductor, Inc... Read: Write: 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 RESULT Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 18-16. Left-Justified Signed Result Register (LJSRR) S -- Sign Bit RESULT[14:6] -- Result Field The conversion result is signed, left-justified data. 18.8.8.3 Left-Justified Unsigned Result Register Address: 0x00ca_0380 through 0x00ca_03fe Bit 15 14 13 12 Read: 11 10 9 Bit 8 RESULT Write: Reset: Bit 7 Read: Write: Reset: 6 RESULT 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 18-17. Left-Justified Unsigned Result Register (LJURR) RESULT[15:6] -- Result Field The conversion result is unsigned, left-justified data. Technical Data 442 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Functional Description 18.9 Functional Description This subsection provides a functional description of the QADC. 18.9.1 QADC Bus Accessing Coherency of results read across multiple cycles is not guaranteed. Freescale Semiconductor, Inc... 18.9.2 External Multiplexing External multiplexer chips concentrate a number of analog signals onto a few inputs to the analog converter. This is helpful in applications that need to convert more analog signals than the A/D converter can normally provide. External multiplexing also puts the multiplexed chip closer to the signal source. This minimizes the number of analog signals that need to be shielded due to the proximity to noisy high speed digital signals at the microcontroller chip. For example, four 4-input multiplexer chips can be put at the connector where the analog signals first arrive on the computer board. As a result, only four analog signals need to be shielded from noise as they approach the microcontroller chip, rather than having to protect 16 analog signals. However, external multiplexer chips may introduce additional noise and errors if not properly utilized. Therefore, it is necessary to maintain low "on" resistance (the impedance of an analog switch when active within a multiplexed chip) and insert a low pass filter (R/C) on the input side of the multiplexed chip. 18.9.2.1 External Multiplexing Operation The QADC can use from one to four or two dual external multiplexer chips to expand the number of analog signals that may be converted. Up to 16 analog channels can be converted through external multiplexer selection. The externally multiplexed channels are automatically selected from the channel field of the conversion command word (CCW) table, the same as internally multiplexed channels. The software selects the external multiplexed mode by setting the MUX bit in control register 0 (QACR0). MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 443 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Freescale Semiconductor, Inc... Figure 18-18 shows the maximum configuration of four external multiplexer chips connected to the QADC. The external multiplexer chips select one of four analog inputs and connect it to one analog output, which becomes an input to the QADC. The QADC provides two multiplexed address signals -- MA[1:0] -- to select one of four inputs. These inputs are connected to all four external multiplexer chips. The analog output of the four multiplex chips are each connected to separate QADC inputs (ANw, ANx, ANy, and ANz) as shown in Figure 18-18. When the external multiplexed mode is selected, the QADC automatically creates the MA output signals from the channel number in each CCW. The QADC also converts the proper input channel (ANw, ANx, ANy, and ANz) by interpreting the CCW channel number. As a result, up to 16 externally multiplexed channels appear to the conversion queues as directly connected signals. The software simply puts the channel number of externally multiplexed channels into CCWs. Figure 18-18 shows that the two MA signals may also be analog input pins. When external multiplexing is selected, none of the MA pins can be used for analog or digital inputs. They become multiplexed address outputs and are unaffected by DDRQA[1:0]. 18.9.2.2 Module Version Options The number of available analog channels varies, depending on whether external multiplexing is used. A maximum of 16 analog channels are supported by the internal multiplexing circuitry of the converter. Table 18-12 shows the total number of analog input channels supported with 0 to four external multiplexer chips. Table 18-12. Analog Input Channels Number of Analog Input Channels Available Directly Connected + External Multiplexed = Total Channels(1), (2) No External Mux One External Mux Two External Muxes Three External Muxes Four External Muxes 8 5+4=9 4 + 8 = 12 3 + 12 = 15 2 + 16 = 18 1. The external trigger inputs are not shared with two analog input pins. 2. When external multiplexing is used, two input channels can be configured as multiplexed address outputs, and for each external multiplexer chip, one input channel is a multiplexed analog input. Technical Data 444 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Functional Description Freescale Semiconductor, Inc... AN1 AN3 AN5 AN7 MUX MUX AN0/ANW/PQB0 AN1/ANX/PQB1 AN2/ANY/PQB2 AN3/ANZ/PQB3 PORT QB AN0 AN2 AN4 AN6 AN55/ETRIG1PQA3 AN56/ETRIG2/PQA4 AN16 AN18 AN20 AN22 AN17 AN19 AN21 AN23 PORT QA AN52/MA0/PQA0 AN53/MA1/PQA1 MUX MUX Figure 18-18. External Multiplexing Configuration MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 445 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) 18.9.2.3 External Multiplexed Address Configuration The QADC can drive external multiplexed addresses. If configured to drive external addresses, the external address pins MA[1:0] will function as address pins and will not maintain analog input functions in external address mode. Freescale Semiconductor, Inc... 18.9.3 Analog Subsystem This section describes the QADC analog subsystem, which includes the front-end analog multiplexer and analog-to-digital converter. 18.9.3.1 Analog-to-Digital Converter Operation The analog subsystem consists of the path from the input pins to the A/D converter block. Signals from the queue control logic are fed to the multiplexer and state machine. The end-of-conversion (EOC) signal and the successive-approximation register (SAR) reflect the result of the conversion. Figure 18-19 shows a block diagram of the QADC analog subsystem. NOTE: The following description assumes the use of a buffer amplifier. 18.9.3.2 Conversion Cycle Times Total conversion time is made up of initial sample time, final sample time, and resolution time. Initial sample time refers to the time during which the selected input channel is coupled through the buffer amplifier to the sample capacitor. This buffer is used to quickly reproduce its input signal on the sample capacitor and minimize charge sharing errors. During the final sampling period the amplifier is bypassed, and the multiplexer input charges the sample capacitor array directly for improved accuracy. During the resolution period, the voltage in the sample capacitor is converted to a digital value and stored in the SAR. Initial sample time is fixed at two QCLK cycles. Final sample time can be 2, 4, 8, or 16 QCLK cycles, depending on the value of the IST field in the CCW. Resolution time is 10 QCLK cycles. Technical Data 446 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Functional Description PQA4 10-BIT A/D CONVERTER 4 CHAN[5:0] INPUT PQA0 PQB3 Freescale Semiconductor, Inc... BIAS CIRCUIT SAMPLE BUFFER INTERNAL CHANNEL DECODE PQB0 POWER DOWN STOP RST QCLK 2 CSAMP STATE MACHINE & LOGIC BYP START CONV. END OF CONV. SAR TIMING VRH 10-BIT RC DAC 10 VRL IST SIGNALS FROM/TO QUEUE CONTROL LOGIC CHAN. DECODE & MUX 8: 1 SAR[9:0] 10 VDDA ANALOG POWER SUCCESSIVE APPROXIMATION REGISTER COMPARATOR VSSA Figure 18-19. QADC Analog Subsystem Block Diagram Therefore, conversion time requires a minimum of 14 QCLK clocks (7 s with a 2.0-MHz QCLK). If the maximum final sample time period of 16 QCLKs is selected, the total conversion time is 28 QCLKs or 14 s (with a 2.0-MHz QCLK). BUFFER SAMPLE TIME: 2 CYCLES FINAL SAMPLE TIME: N CYCLES (2,4,8,16) RESOLUTION TIME: 10 CYCLES QCLK SAMPLE TIME SUCCESSIVE APPROXIMATION RESOLUTION SEQUENCE Figure 18-20. Conversion Timing MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 447 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Freescale Semiconductor, Inc... If the amplifier bypass mode is enabled for a conversion by setting the amplifier bypass (BYP) field in the CCW, the timing changes to that shown in Figure 18-21. See 18.8.7 Conversion Command Word Table for more information on the BYP field. The initial sample time is eliminated, reducing the potential conversion time by two QCLKs. When using the bypass mode, the external circuit should be of low source impedance (typically less than 10 k). Also, the loading effects to the external circuitry by the QADC need to be considered, since the benefits of the sample amplifier are not present. NOTE: Because of internal RC time constants, it is not recommended to use a sample time of two QCLKs in bypass mode for high-frequency operation. SAMPLE TIME: N CYCLES (2,4,8,16) RESOLUTION TIME: 10 CYCLES SAMPLE TIME SUCCESSIVE-APPROXIMATION RESOLUTION SEQUENCE QCLK Figure 18-21. Bypass Mode Conversion Timing 18.9.3.3 Channel Decode and Multiplexer The internal multiplexer selects one of the eight analog input pins for conversion. The selected input is connected to the Sample Buffer Amplifier or to the sample capacitor. The multiplexer also includes positive and negative stress protection circuitry, which prevents deselected channels from affecting the selected channel when current is injected into the deselected channels. 18.9.3.4 Sample Buffer The sample buffer is used to raise the effective input impedance of the A/D converter, so that external components (higher bandwidth or higher impedance) are less critical to accuracy. The input voltage is buffered onto the sample capacitor to reduce crosstalk between channels. Technical Data 448 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Functional Description 18.9.3.5 Digital-to-Analog Converter (DAC) Array Freescale Semiconductor, Inc... The digital-to-analog converter (DAC) array consists of binary-weighted capacitors and a resistor-divider chain. The reference voltages, VRH and VRL, are used by the DAC to perform ratiometric conversions. The DAC also converts the following three internal channels: * VRH -- reference voltage high * VRL -- reference voltage low * (VRH-VRL)/2 -- reference voltage The DAC array serves to provide a mechanism for the successive approximation A/D conversion. Resolution begins with the most significant bit (MSB) and works down to the least significant bit (LSB). The switching sequence is controlled by the comparator and SAR logic. The sample capacitor samples and holds the voltage to be converted. 18.9.3.6 Comparator During the approximation process, the comparator senses whether the digitally selected arrangement of the DAC array produces a voltage level higher or lower than the sampled input. The comparator output feeds into the SAR which accumulates the A/D conversion result sequentially, beginning with the MSB. 18.9.3.7 Bias The bias circuit is controlled by the STOP signal to power-up and power-down all the analog circuits. 18.9.3.8 Successive-Approximation Register The input of the SAR is connected to the comparator output. The SAR sequentially receives the conversion value one bit at a time, starting with the MSB. After accumulating the 10 bits of the conversion result, the SAR data is transferred to the appropriate result location, where it may be read from the IPbus by user software. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 449 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) 18.9.3.9 State Machine Freescale Semiconductor, Inc... The state machine receives the QCLK, RST, STOP, IST[1:0], BYP, CHAN[5:0], and START CONV. signals, from which it generates all timing to perform an A/D conversion. The start-conversion signal (START CONV.) indicates to the A/D converter that the desired channel has been sent to the MUX. IST[1:0] indicates the desired sample time. BYP indicates whether to bypass the sample amplifier. The end-of-conversion (EOC) signal notifies the queue control logic that a result is available for storage in the result RAM. 18.10 Digital Control The digital control subsystem includes the control logic to sequence the conversion activity, the clock and periodic/interval timer, control and status registers, the conversion command word table RAM, and the result word table RAM. The central element for control of the QADC conversions is the 64-entry conversion command word (CCW) table. Each CCW specifies the conversion of one input channel. Depending on the application, one or two queues can be established in the CCW table. A queue is a scan sequence of one or more input channels. By using a pause mechanism, subqueues can be created in the two queues. Each queue can be operated using one of several different scan modes. The scan modes for queue 1 and queue 2 are programmed in the control registers QACR1 and QACR2. Once a queue has been started by a trigger event (any of the ways to cause the QADC to begin executing the CCWs in a queue or subqueue), the QADC performs a sequence of conversions and places the results in the result word table. 18.10.1 Queue Priority Timing Examples This subsection describes the QADC priority scheme when trigger events on two queues overlap or conflict. Technical Data 450 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Digital Control 18.10.1.1 Queue Priority Freescale Semiconductor, Inc... Queue 1 has priority over queue 2 execution. These cases show the conditions under which queue 1 asserts its priority: * When a queue is not active, a trigger event for queue 1 or queue 2 causes the corresponding queue execution to begin. * When queue 1 is active and a trigger event occurs for queue 2, queue 2 cannot begin execution until queue 1 reaches completion or the paused state. The status register records the trigger event by reporting the queue 2 status as trigger pending. Additional trigger events for queue 2, which occur before execution can begin, are captured as trigger overruns. * When queue 2 is active and a trigger event occurs for queue 1, the current queue 2 conversion is aborted. The status register reports the queue 2 status as suspended. Any trigger events occurring for queue 2 while queue 2 is suspended are captured as trigger overruns. Once queue 1 reaches the completion or the paused state, queue 2 begins executing again. The programming of the RESUME bit in QACR2 determines which CCW is executed in queue 2. * When simultaneous trigger events occur for queue 1 and queue 2, queue 1 begins execution and the queue 2 status is changed to trigger pending. * Subqueues that are paused The pause feature can be used to divide queue 1 and/or queue 2 into multiple subqueues. A subqueue is defined by setting the pause bit in the last CCW of the subqueue. Figure 18-22 shows the CCW format and an example of using pause to create subqueues. Queue 1 is shown with four CCWs in each subqueue and queue 2 has two CCWs in each subqueue. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 451 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) CONVERSION COMMAND WORD (CCW) TABLE RESULT WORD TABLE P 00 0 BEGINNING OF QUEUE 1 00 0 0 1 PAUSE 0 0 0 1 PAUSE 0 * Freescale Semiconductor, Inc... * * * P * 0 BQ2 0 END OF QUEUE 1 0 BEGINNING OF QUEUE 2 1 PAUSE CHANNEL SELECT, SAMPLE, HOLD, A/D CONVERSION * 0 1 PAUSE 0 1 PAUSE 0 63 * * * * P * * 1 PAUSE 0 END OF QUEUE 2 63 Figure 18-22. QADC Queue Operation with Pause The queue operating mode selected for queue 1 determines what type of trigger event causes the execution of each of the subqueues within queue 1. Similarly, the queue operating mode for queue 2 determines the type of trigger event required to execute each of the subqueues within queue 2. For example, when the external trigger rising edge continuous-scan mode is selected for queue 1, and there are six subqueues within queue 1, a separate rising edge is required on the external trigger pin after every pause to begin the execution of each subqueue (refer to Figure 18-22). The choice of single-scan or continuous-scan applies to the full queue, and is not applied to each subqueue. Once a subqueue is initiated, each Technical Data 452 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Digital Control Freescale Semiconductor, Inc... CCW is executed sequentially until the last CCW in the subqueue is executed and the pause state is entered. Execution can only continue with the next CCW, which is the beginning of the next subqueue. A subqueue cannot be executed a second time before the overall queue execution has been completed. Trigger events which occur during the execution of a subqueue are ignored, except that the trigger overrun flag is set. When a continuous-scan mode is selected, a trigger event occurring after the completion of the last subqueue (after the queue completion flag is set), causes the execution to continue with the first subqueue, starting with the first CCW in the queue. When the QADC encounters a CCW with the pause bit set, the queue enters the paused state after completing the conversion specified in the CCW with the pause bit. The pause flag is set and a pause software interrupt may optionally be issued. The status of the queue is shown to be paused, indicating completion of a subqueue. The QADC then waits for another trigger event to again begin execution of the next subqueue. 18.10.1.2 Queue Priority Schemes Since there are two conversion command queues and only one A/D converter, there is a priority scheme to determine which conversion is to occur. Each queue has a variety of trigger events that are intended to initiate conversions, and they can occur asynchronously in relation to each other and other conversions in progress. For example, a queue can be idle awaiting a trigger event, a trigger event can have occurred, but the first conversion has not started, a conversion can be in progress, a pause condition can exist awaiting another trigger event to continue the queue, and so on. The following paragraphs and figures outline the prioritizing criteria used to determine which conversion occurs in each overlap situation. NOTE: Each situation in Figure 18-23 through Figure 18-33 are labeled S1 through S19. In each diagram, time is shown increasing from left to right. The execution of queue 1 and queue 2 (Q1 and Q2) is shown as a string of rectangles representing the execution time of each CCW in the queue. In most of the situations, there are four CCWs (labeled C1 to C4) in both queue 1 and queue 2. In some of the situations, CCW C2 is presumed MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 453 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) to have the pause bit set, to show the similarities of pause and end-of-queue as terminations of queue execution. Trigger events are described in Table 18-13. Table 18-13. Trigger Events Freescale Semiconductor, Inc... Trigger Events T1 Events that trigger queue 1 execution (external trigger, software-initiated single-scan enable bit, or completion of the previous continuous loop) T2 Events that trigger queue 2 execution (external trigger, software-initiated single-scan enable bit, timer period/interval expired, or completion of the previous continuous loop) When a trigger event causes a CCW execution in progress to be aborted, the aborted conversion is shown as a ragged end of a shortened CCW rectangle. The situation diagrams also show when key status bits are set. Table 18-14 describes the status bits. Table 18-14. Status Bits Bit Function CF flag Set when the end of the queue is reached PF flag Set when a queue completes execution up through a pause bit Trigger overrun error (TOR) Set when a new trigger event occurs before the queue is finished serving the previous trigger event Below the queue execution flows are three sets of blocks that show the status information that is made available to the software. The first two rows of status blocks show the condition of each queue as: * Idle * Active * Pause * Suspended (queue 2 only) * Trigger pending The third row of status blocks shows the 4-bit QS status register field that encodes the condition of the two queues. Two transition status cases, Technical Data 454 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Digital Control QS = 0011 and QS = 0111, are not shown because they exist only very briefly between stable status conditions. Freescale Semiconductor, Inc... The first three examples in Figure 18-23 through Figure 18-25 (S1, S2, and S3) show what happens when a new trigger event is recognized before the queue has completed servicing the previous trigger event on the same queue. In situation S1 (Figure 18-23), one trigger event is being recognized on each queue while that queue is still working on the previously recognized trigger event. The trigger overrun error status bit is set, and otherwise, the premature trigger event is ignored. A trigger event which occurs before the servicing of the previous trigger event is through does not disturb the queue execution in progress. T1 Q1: T1 C1 C2 C3 C4 T2 TOR1 T2 CF1 Q2: C1 C2 C3 TOR2 Q1 IDLE QS 0000 ACTIVE 1000 CF2 IDLE ACTIVE IDLE Q2 C4 0000 0010 IDLE 0000 Figure 18-23. CCW Priority Situation 1 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 455 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Freescale Semiconductor, Inc... In situation S2 (Figure 18-24), more than one trigger event is recognized before servicing of a previous trigger event is complete, the trigger overrun bit is again set, but otherwise, the additional trigger events are ignored. After the queue is complete, the first newly detected trigger event causes queue execution to begin again. When the trigger event rate is high, a new trigger event can be seen very soon after completion of the previous queue, leaving software little time to retrieve the previous results. Also, when trigger events are occurring at a high rate for queue 1, the lower priority queue 2 channels may not get serviced at all. T1 T1 T1 T1 T1 T2 Q1: C1 C2 C3 C4 C1 C2 C3 Q2: TOR1 TOR1 TOR1 CF1 T2 T2 C2 C3 C4 C1 TOR2 TOR2 Q1 IDLE ACTIVE ACTIVE 1000 1000 CF2 IDLE IDLE Q2 QS IDLE C4 CF1 0000 ACTIVE IDLE 0010 0000 Figure 18-24. CCW Priority Situation 2 Technical Data 456 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Digital Control Situation S3 (Figure 18-25) shows that when the pause feature is in use, the trigger overrun error status bit is set the same way, and that queue execution continues unchanged. T1 Q1: T1 C1 T1 C2 C3 T2 TOR1 Freescale Semiconductor, Inc... T2 TOR1 C1 0000 PF2 0100 CF2 IDLE ACTIVE PAUSE 0110 C4 TOR2 ACTIVE 1000 T2 C3 PAUSE IDLE Q2 QS ACTIVE CF1 C2 TOR2 IDLE C4 T2 PF1 Q2: Q1 T1 1001 0101 0001 ACTIVE IDLE 0010 0000 Figure 18-25. CCW Priority Situation 3 The next two situations consider trigger events that occur for the lower priority queue 2, while queue 1 is actively being serviced. Situation S4 (Figure 18-26) shows that a queue 2 trigger event that is recognized while queue 1 is active is saved, and as soon as queue 1 is finished, queue 2 servicing begins. T1 Q1: C1 C2 C3 C4 CF1 T2 C1 C2 C3 C4 Q2: CF2 Q1 IDLE IDLE Q2 QS ACTIVE 0000 1000 IDLE TRIGGERED ACTIVE IDLE 1011 0010 0000 Figure 18-26. CCW Priority Situation 4 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 457 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Situation S5 (Figure 18-27) shows that when multiple queue 2 trigger events are detected while queue 1 is busy, the trigger overrun error bit is set, but queue 1 execution is not disturbed. Situation S5 also shows that the effect of queue 2 trigger events during queue 1 execution is the same when the pause feature is in use in either queue. T1 T1 Q1: C1 C2 Freescale Semiconductor, Inc... T2 T2 C3 T2 T2 PF1 Q2: C1 Q2 QS IDLE ACTIVE IDLE 0000 1000 CF1 C2 TOR1 Q1 C4 C3 TOR1 PF2 PAUSE TRIG ACTIVE 1011 0110 C4 CF2 IDLE ACTIVE ACTIVE PAUSE 0101 1001 TRIG ACTIVE IDLE 1011 0010 0000 Figure 18-27. CCW Priority Situation 5 The remaining situations, S6 through S11, show the impact of a queue 1 trigger event occurring during queue 2 execution. Queue 1 is higher in priority, the conversion taking place in queue 2 is aborted, so that there is not a variable latency time in responding to queue 1 trigger events. Technical Data 458 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Digital Control In situation 6 (Figure 18-28), the conversion initiated by the second CCW in queue 2 is aborted just before the conversion is complete, so that queue 1 execution can begin. Queue 2 is considered suspended. After queue 1 is finished, queue 2 starts over with the first CCW, when the RES (resume) control bit is set to 0. Situation S7 (Figure 18-29) shows that when pause operation is not in use with queue 2, queue 2 suspension works the same way. Freescale Semiconductor, Inc... T1 Q1: T1 C1 C2 C3 C4 RESUME=0 T2 PF1 CF1 Q2: C1 C1 C2 C2 C3 C4 CF2 Q1 Q2 QS IDLE ACTIVE PAUSE IDLE 0000 0100 1000 ACTIVE ACTIVE IDLE ACTIVE SUSPEND ACTIVE 0110 1010 0010 IDLE 0000 Figure 18-28. CCW Priority Situation 6 T1 Q1: T1 C1 C2 C3 C4 RESUME = 0 T2 PF1 Q2: CF1 C1 C1 C2 C2 C3 C4 CF2 Q1 Q2 QS IDLE ACTIVE PAUSE IDLE 0000 1000 0100 ACTIVE ACTIVE IDLE ACTIVE SUSPEND ACTIVE 0110 1010 0010 IDLE 0000 Figure 18-29. CCW Priority Situation 7 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 459 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Situations S8 and S9 (Figure 18-30 and Figure 18-31) repeat the same two situations with the RESUME bit set to a 1. When the RES bit is set, following suspension, queue 2 resumes execution with the aborted CCW, not the first CCW in the queue. T1 Q1: T1 C1 C2 C3 C4 T2 PF1 CF1 Freescale Semiconductor, Inc... Q2: C1 C2 C2 C3 C4 RESUME=1 CF2 IDLE Q1 ACTIVE PAUSE IDLE Q2 QS 0000 IDLE ACTIVE SUSPEND ACTIVE IDLE 0110 1010 0010 0000 0100 1000 ACTIVE ACTIVE Figure 18-30. CCW Priority Situation 8 T1 Q1: T1 C1 C2 T2 Q2: C3 PF1 C1 C1 C2 C4 T2 CF1 C3 C2 C4 C4 PF2 ACTIVE IDLE Q1 RESUME=1 CF2 PAUSE Q2 IDLE ACTIVE SUSPEND ACT PAUSE QS 0000 0010 1010 0110 0101 ACTIVE ACTIVE 0110 IDLE SUSPEND ACT IDLE 1010 0010 0000 Figure 18-31. CCW Priority Situation 9 Technical Data 460 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Digital Control Situations S10 and S11 (Figure 18-32 and Figure 18-33) show that when an additional trigger event is detected for queue 2 while the queue is suspended, the trigger overrun error bit is set, the same as if queue 2 were being executed when a new trigger event occurs. Trigger overrun on queue 2 thus permits the software to know that queue 1 is taking up so much QADC time that queue 2 trigger events are being lost. T1 Freescale Semiconductor, Inc... Q1: C1 T2 Q2: T1 C2 T2 C1 C3 PF1 T2 C1 C2 C2 TOR2 T2 C3 IDLE ACTIVE SUSPEND ACTIVE QS 0000 0010 1010 0110 C4 TOR2 PAUSE Q2 CF1 C3 PF2 ACTIVE IDLE Q1 C4 CF2 ACTIVE PAUSE ACT 0101 0110 RESUME = 0 IDLE SUSPEND ACTIVE IDLE 1010 0010 0000 Figure 18-32. CCW Priority Situation 10 T1 Q1: T2 Q2: T1 C1 C2 T2 C1 C2 PF1 T2 Q2 IDLE ACTIVE SUSPEND QS 0000 0010 1010 C4 PF2 ACTIVE IDLE CF1 ACT PAUSE 0101 RESUME = 1 C4 CF2 TOR2 PAUSE 0110 C4 T2 C3 C2 TOR2 Q1 C3 ACTIVE IDLE ACTIVE SUSPEND ACT IDLE 0110 1010 0010 0000 Figure 18-33. CCW Priority Situation 11 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 461 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Freescale Semiconductor, Inc... The previous situations cover normal overlap conditions that arise with asynchronous trigger events on the two queues. An additional conflict to consider is that the freeze condition can arise while the QADC is actively executing CCWs. The conventional use for the debug mode is for software/hardware debugging. When the CPU background debug mode is enabled and a breakpoint occurs, the freeze signal is issued, which can cause peripheral modules to stop operation. When freeze is detected, the QADC completes the conversion in progress, unlike queue 1 suspending queue 2. After the freeze condition is removed, the QADC continues queue execution with the next CCW in sequence. Trigger events that occur during freeze are not captured. When a trigger event is pending for queue 2 before freeze begins, that trigger event is remembered when the freeze is passed. Similarly, when freeze occurs while queue 2 is suspended, after freeze, queue 2 resumes execution as soon as queue 1 is finished. Situations 12 through 19 (Figure 18-34 to Figure 18-41) show examples of all of the freeze situations. FREEZE T1 Q1: C1 C2 C3 C4 CF1 Figure 18-34. CCW Freeze Situation 12 FREEZE T2 Q2: C1 C2 C3 C4 CF2 Figure 18-35. CCW Freeze Situation 13 Technical Data 462 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Digital Control (TRIGGERS IGNORED) FREEZE T1 Q1: T1 C1 T1 C2 C3 T2 C4 T2 CF1 Freescale Semiconductor, Inc... Figure 18-36. CCW Freeze Situation 14 (TRIGGERS IGNORED) FREEZE T2 Q2: T2 C1 T2 C2 C3 T1 C4 T1 CF2 Figure 18-37. CCW Freeze Situation 15 (TRIGGERS IGNORED) FREEZE T1 Q1: T1 C1 C2 T1 C3 PF1 C4 CF1 Figure 18-38. CCW Freeze Situation 16 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 463 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) (TRIGGERS IGNORED) FREEZE T2 T2 Q2: C1 T2 C2 C3 C4 PF2 CF2 Freescale Semiconductor, Inc... Figure 18-39. CCW Freeze Situation 17 FREEZE T1 Q1: C1 C2 C3 C4 T2 CF1 (TRIGGER CAPTURED, RESPONSE DELAYED AFTER FREEZE) Q2: C1 C2 C3 C4 CF2 Figure 18-40. CCW Freeze Situation 18 FREEZE T1 Q1: C1 C2 C3 T2 Q2: C4 CF1 C1 C2 C3 C4 C4 CF2 Figure 18-41. CCW Freeze Situation 19 Technical Data 464 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Digital Control 18.10.2 Boundary Conditions Freescale Semiconductor, Inc... The queue operation boundary conditions are: NOTE: * The first CCW in a queue contains channel 63, the end-of-queue (EOQ) code. The queue becomes active and the first CCW is read. The end-of-queue is recognized, the completion flag is set, and the queue becomes idle. A conversion is not performed. * BQ2 (beginning of queue 2) is set at the end of the CCW table (63) and a trigger event occurs on queue 2. The end-of-queue condition is recognized, a conversion is performed, the completion flag is set, and the queue becomes idle. * BQ2 is set to CCW0 and a trigger event occurs on queue 1. After reading CCW0, the end-of-queue condition is recognized, the completion flag is set, and the queue becomes idle. A conversion is not performed. * BQ2 (beginning of queue 2) is set beyond the end of the CCW table (64-127) and a trigger event occurs on queue 2. The end-of-queue condition is recognized immediately, the completion flag is set, and the queue becomes idle. A conversion is not performed. Multiple end-of-queue conditions may be recognized simultaneously, although there is no change in the QADC behavior. For example, if BQ2 is set to CCW0, CCW0 contains the EOQ code, and a trigger event occurs on queue 1, the QADC reads CCW0 and detects both end-of-queue conditions. The completion flag is set and queue 1 becomes idle. Boundary conditions also exist for combinations of pause and end-of-queue. One case is when a pause bit is in one CCW and an end-of-queue condition is in the next CCW. The conversion specified by the CCW with the pause bit set completes normally. The pause flag is set. However, since the end-of-queue condition is recognized, the completion flag is also set and the queue status becomes idle, not paused. Examples of this situation include: * The pause bit is set in CCW5 and the channel 63 (EOQ) code is in CCW6. * The pause is in CCW63. * During queue 1 operation, the pause bit is set in CCW20 and BQ2 points to CCW21. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 465 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Freescale Semiconductor, Inc... Another pause and end-of-queue boundary condition occurs when the pause and an end-of-queue condition occur in the same CCW. Both the pause and end-of-queue conditions are recognized simultaneously. The end-of-queue condition has precedence so a conversion is not performed for the CCW and the pause flag is not set. The QADC sets the completion flag and the queue status becomes idle. Examples of this situation are: * The pause bit is set in CCW10 and EOQ is programmed into CCW10. * During queue 1 operation, the pause bit set in CCW32, which is also BQ2. 18.10.3 Scan Modes The QADC queuing mechanism allows the application to utilize different requirements for automatically scanning input channels. In single-scan mode, a single pass through a sequence of conversions defined by a queue is performed. In continuous-scan mode, multiple passes through a sequence of conversions defined by a queue are executed. The possible modes are: * Disabled mode and reserved mode * Software-initiated single-scan mode * External trigger single-scan mode * External gated single-scan mode * Interval timer single-scan mode * Software-initiated continuous-scan mode * External trigger continuous-scan mode * External gated continuous-scan mode * Periodic timer continuous-scan mode These paragraphs describe single-scan and continuous-scan operations. Technical Data 466 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Digital Control 18.10.4 Disabled Mode When the disabled mode is selected, the queue is not active. Trigger events cannot initiate queue execution. When both queue 1 and queue 2 are disabled, wait states are not encountered for IPbus accesses of the RAM. When both queues are disabled, it is safe to change the QCLK prescaler values. Freescale Semiconductor, Inc... 18.10.5 Reserved Mode Reserved mode allows for future mode definitions. When the reserved mode is selected, the queue is not active. It functions the same as disabled mode. 18.10.6 Single-Scan Modes When the application software wants to execute a single pass through a sequence of conversions defined by a queue, a single-scan queue operating mode is selected. By programming the MQ field in QACR1 or QACR2, these modes can be selected: NOTE: * Software-initiated single-scan mode * External trigger single-scan mode * External gated single-scan mode * Interval timer single-scan mode Queue 2 cannot be programmed for external gated single-scan mode. In all single-scan queue operating modes, the software must also enable the queue to begin execution by writing the single-scan enable bit to a 1 in the queue's control register. The single-scan enable bits, SSE1 and SSE2, are provided for queue 1 and queue 2 respectively. Until the single-scan enable bit is set, any trigger events for that queue are ignored. The single-scan enable bit may be set to a 1 during the write cycle, which selects the single-scan queue operating mode. The single-scan enable bit is set through software, but will always read as a 0. Once set, writing the single-scan enable bit to 0 has no effect. Only the QADC can clear the single-scan enable bit. The completion flag, MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 467 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Freescale Semiconductor, Inc... completion interrupt, or queue status are used to determine when the queue has completed. After the single-scan enable bit is set, a trigger event causes the QADC to begin execution with the first CCW in the queue. The single-scan enable bit remains set until the queue is completed. After the queue reaches completion, the QADC resets the single-scan enable bit to 0. If the single-scan enable bit is written to a 1 or a 0 by the software before the queue scan is complete, the queue is not affected. However, if the software changes the queue operating mode, the new queue operating mode and the value of the single-scan enable bit are recognized immediately. The conversion in progress is aborted and the new queue operating mode takes effect. In the software-initiated single-scan mode, the writing of a 1 to the single-scan enable bit causes the QADC to generate a trigger event internally and the queue execution begins immediately. In the other single-scan queue operating modes, once the single-scan enable bit is written, the selected trigger event must occur before the queue can start. The single-scan enable bit allows the entire queue to be scanned once. A trigger overrun is captured if a trigger event occurs during queue execution in an edge-sensitive external trigger mode or a periodic/interval timer mode. In the interval timer single-scan mode, the next expiration of the timer is the trigger event for the queue. After the queue execution is complete, the queue status is shown as idle. The software can restart the queue by setting the single-scan enable bit to a 1. Queue execution begins with the first CCW in the queue. 18.10.6.1 Software-Initiated Single-Scan Mode Software can initiate the execution of a scan sequence for queues 1 or 2 by selecting the software-initiated single-scan mode, and writing the single-scan enable bit in QACR1 or QACR2. A trigger event is generated internally and the QADC immediately begins execution of the first CCW in the queue. If a pause occurs, another trigger event is generated internally, and then execution continues without pausing. The QADC automatically performs the conversions in the queue until an end-of-queue condition is encountered. The queue remains idle until the software again sets the single-scan enable bit. While the time to Technical Data 468 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Digital Control internally generate and act on a trigger event is very short, software can momentarily read the status conditions, indicating that the queue is paused. The trigger overrun flag is never set while in the software-initiated single-scan mode. Freescale Semiconductor, Inc... The software-initiated single-scan mode is useful in these applications: * Allows software complete control of the queue execution * Allows the software to easily alternate between several queue sequences 18.10.6.2 External Trigger Single-Scan Mode The external trigger single-scan mode is available on both queue 1 and queue 2. The software programs the polarity of the external trigger edge that is to be detected, either a rising or a falling edge. The software must enable the scan to occur by setting the single-scan enable bit for the queue. The first external trigger edge causes the queue to be executed one time. Each CCW is read and the indicated conversions are performed until an end-of-queue condition is encountered. After the queue is completed, the QADC clears the single-scan enable bit. Software may set the single-scan enable bit again to allow another scan of the queue to be initiated by the next external trigger edge. The external trigger single-scan mode is useful when the input trigger rate can exceed the queue execution rate. Analog samples can be taken in sync with an external event, even though the software is not interested in data taken from every edge. The software can start the external trigger single-scan mode and get one set of data, and at a later time, start the queue again for the next set of samples. When a pause bit is encountered during external trigger single-scan mode, another trigger event is required for queue execution to continue. Software involvement is not needed to enable queue execution to continue from the paused state. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 469 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) 18.10.6.3 External Gated Single-Scan Mode Freescale Semiconductor, Inc... The QADC provides external gating for queue 1 only. When external gated single-scan mode is selected, the input level on the associated external trigger pin enables and disables queue execution. The polarity of the external gated signal is fixed so only a high level opens the gate and a low level closes the gate. Once the gate is open, each CCW is read and the indicated conversions are performed until the gate is closed. Software must enable the scan to occur by setting the single-scan enable bit for queue 1. If a pause in a CCW is encountered, the pause flag does not become set, and execution continues without pausing. While the gate is open, queue 1 executes one time. Each CCW is read and the indicated conversions are performed until an end-of-queue condition is encountered. When queue 1 completes, the QADC sets the completion flag (CF1) and clears the single-scan enable bit. Software may set the single-scan enable bit again to allow another scan of queue 1 to be initiated during the next open gate. If the gate closes before queue 1 completes execution, the current CCW completes, execution of queue 1 stops, the single-scan enable bit is cleared, and the PF1 bit is set. Software can read the CWPQ1 to determine the last valid conversion in the queue. Software must set the single-scan enable bit again and should clear the PF1 bit before another scan of queue 1 is initiated during the next open gate. The start of queue 1 is always the first CCW in the CCW table. Since the condition of the gate is only sampled after each conversion during queue execution, closing the gate for a period less than a conversion time interval does not guarantee the closure will be captured. 18.10.6.4 Interval Timer Single-Scan Mode Both queues can use the periodic/interval timer in a single-scan queue operating mode. The timer interval can range from 128 to 128 KQCLK cycles in binary multiples. When the interval timer single-scan mode is selected and the software sets the single-scan enable bit in QACR1(2), the timer begins counting. When the time interval elapses, an internal trigger event is created to start the queue and the QADC begins execution with the first CCW. Technical Data 470 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Digital Control The QADC automatically performs the conversions in the queue until a pause or an end-of-queue condition is encountered. When a pause occurs, queue execution stops until the timer interval elapses again, and queue execution continues. When the queue execution reaches an end-of-queue situation, the single-scan enable bit is cleared. Software may set the single-scan enable bit again, allowing another scan of the queue to be initiated by the interval timer. Freescale Semiconductor, Inc... The interval timer generates a trigger event whenever the time interval elapses. The trigger event may cause the queue execution to continue following a pause, or may be considered a trigger overrun. Once the queue execution is completed, the single-scan enable bit must be set again to enable the timer to count again. Normally, only one queue will be enabled for interval timer single-scan mode and the timer will reset at the end-of-queue. However, if both queues are enabled for either single-scan or continuous interval timer mode, the end-of-queue condition will not reset the timer while the other queue is active. In this case, the timer will reset when both queues have reached end-of-queue. See 18.10.9 Periodic/Interval Timer for a definition of interval timer reset conditions. The interval timer single-scan mode can be used in applications which need coherent results, for example: * When it is necessary that all samples are guaranteed to be taken during the same scan of the analog pins. * When the interrupt rate in the periodic timer continuous-scan mode would be too high. * In sensitive battery applications, where the single-scan mode uses less power than the software-initiated continuous-scan mode. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 471 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) 18.10.7 Continuous-Scan Modes Freescale Semiconductor, Inc... When the application software wants to execute multiple passes through a sequence of conversions defined by a queue, a continuous-scan queue operating mode is selected. By programming the MQ1(2) field in QACR1(2), these software-initiated modes can be selected: * Software-initiated continuous-scan mode * External trigger continuous-scan mode * External gated continuous-scan mode * Periodic timer continuous-scan mode When a queue is programmed for a continuous-scan mode, the single-scan enable bit in the queue control register does not have any meaning or effect. As soon as the queue operating mode is programmed, the selected trigger event can initiate queue execution. In the case of the software-initiated continuous-scan mode, the trigger event is generated internally and queue execution begins immediately. In the other continuous-scan queue operating modes, the selected trigger event must occur before the queue can start. A trigger overrun is captured if a trigger event occurs during queue execution in the external trigger continuous-scan mode and the periodic timer continuous-scan mode. After the queue execution is complete, the queue status is shown as idle. Since the continuous-scan queue operating modes allow the entire queue to be scanned multiple times, software involvement is not needed to enable queue execution to continue from the idle state. The next trigger event causes queue execution to begin again, starting with the first CCW in the queue. NOTE: Coherent samples are guaranteed. The time between consecutive conversions has been designed to be consistent. However, there is one exception. For queues that end with a CCW containing EOQ code (channel 63), the last queue conversion to the first queue conversion requires one additional CCW fetch cycle. Therefore continuous samples are not coherent at this boundary. In addition, the time from trigger to first conversion can not be guaranteed since it is a function of clock synchronization, programmable trigger events, queue priorities, and so on. Technical Data 472 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Digital Control 18.10.7.1 Software-Initiated Continuous-Scan Mode When the software-initiated continuous-scan mode is programmed, the trigger event is generated automatically by the QADC. Queue execution begins immediately. If a pause is encountered, another trigger event is generated internally, and then execution continues without pausing. When the end-of-queue is reached, another internal trigger event is generated and queue execution begins again from the beginning of the queue. Freescale Semiconductor, Inc... While the time to internally generate and act on a trigger event is very short, software can momentarily read the status conditions, indicating that the queue is idle. The trigger overrun flag is never set while in the software-initiated continuous-scan mode. The software-initiated continuous-scan mode keeps the result registers updated more frequently than any of the other queue operating modes. The software can always read the result table to get the latest converted value for each channel. The channels scanned are kept up to date by the QADC without software involvement. Software can read a result value at any time. The software-initiated continuous-scan mode may be chosen for either queue, but is normally used only with queue 2. When the software-initiated continuous-scan mode is chosen for queue 1, that queue operates continuously and queue 2, being lower in priority, never gets executed. The short interval of time between a queue 1 completion and the subsequent trigger event is not sufficient to allow queue 2 execution to begin. The software-initiated continuous-scan mode is a useful choice with queue 2 for converting channels that do not need to be synchronized to anything, or for the slow-to-change analog channels. Interrupts are normally not used with the software-initiated continuous-scan mode. Rather, the software reads the latest conversion result from the result table at any time. Once initiated, software action is not needed to sustain conversions of channel. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 473 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Freescale Semiconductor, Inc... 18.10.7.2 External Trigger Continuous-Scan Mode The QADC provides external trigger pins for both queues. When the external trigger software-initiated continuous-scan mode is selected, a transition on the associated external trigger pin initiates queue execution. The polarity of the external trigger signal is programmable, so that the software can select a mode which begins queue execution on the rising or falling edge. Each CCW is read and the indicated conversions are performed until an end-of-queue condition is encountered. When the next external trigger edge is detected, the queue execution begins again automatically. Software initialization is not needed between trigger events. When a pause bit is encountered in external trigger continuous-scan mode, another trigger event is required for queue execution to continue. Software involvement is not needed to enable queue execution to continue from the paused state. Some applications need to synchronize the sampling of analog channels to external events. There are cases when it is not possible to use software initiation of the queue scan sequence, since interrupt response times vary. 18.10.7.3 External Gated Continuous-Scan Mode The QADC provides external gating for queue 1 only. When external gated continuous-scan mode is selected, the input level on the associated external trigger pin enables and disables queue execution. The polarity of the external gated signal is fixed so a high level opens the gate and a low level closes the gate. Once the gate is open, each CCW is read and the indicated conversions are performed until the gate is closed. When the gate opens again, the queue execution automatically begins again from the beginning of the queue. Software initialization is not needed between trigger events. If a pause in a CCW is encountered, the pause flag does not become set, and execution continues without pausing. The purpose of external gated continuous-scan mode is to continuously collect digitized samples while the gate is open and to have the most recent samples available. It is up to the programmer to ensure that the queue is large enough so that a maximum gate open time will not reach Technical Data 474 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Digital Control an end-of-queue. However it is useful to take advantage of a smaller queue in the manner described in the next paragraph. Freescale Semiconductor, Inc... In the event that the queue completes before the gate closes, a completion flag will be set and the queue will roll over to the beginning and continue conversions until the gate closes. If the gate remains open and the completion flag is not cleared, when the queue completes a second time the trigger overrun flag will be set and the queue will roll-over again. The queue will continue to execute until the gate closes or the mode is disabled. If the gate closes before queue 1 completes execution, the current CCW completes execution of queue 1 stops and QADC sets the PF1 bit to indicate an incomplete queue. Software can read the CWPQ1 to determine the last valid conversion in the queue. In this mode, if the gate opens again, execution of queue 1 begins again. The start of queue 1 is always the first CCW in the CCW table. Since the condition of the gate is only sampled after each conversion during queue execution, closing the gate for a period less than a conversion time interval does not guarantee the closure will be captured. 18.10.7.4 Periodic Timer Continuous-Scan Mode The QADC includes a dedicated periodic timer for initiating a scan sequence on queue 1 and/or queue 2. Software selects a programmable timer interval ranging from 128 to 128K times the QCLK period in binary multiples. The QCLK period is prescaled down from the IPbus MCU clock. When a periodic timer continuous-scan mode is selected for queue 1 and/or queue 2, the timer begins counting. After the programmed interval elapses, the timer generated trigger event starts the appropriate queue. Meanwhile, the QADC automatically performs the conversions in the queue until an end-of-queue condition or a pause is encountered. When a pause occurs, the QADC waits for the periodic interval to expire again, then continues with the queue. Once end-of-queue has been detected, the next trigger event causes queue execution to begin again with the first CCW in the queue. The periodic timer generates a trigger event whenever the time interval elapses. The trigger event may cause the queue execution to continue following a pause or queue completion, or may be considered a trigger MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 475 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) overrun. As with all continuous-scan queue operating modes, software action is not needed between trigger events. Since both queues may be triggered by the periodic/interval timer, see 18.10.9 Periodic/Interval Timer for a summary of periodic/interval timer reset conditions. Freescale Semiconductor, Inc... Software enables the completion interrupt when using the periodic timer continuous-scan mode. When the interrupt occurs, the software knows that the periodically collected analog results have just been taken. The software can use the periodic interrupt to obtain nonanalog inputs as well, such as contact closures, as part of a periodic look at all inputs. 18.10.8 QADC Clock (QCLK) Generation Figure 18-42 is a block diagram of the clock subsystem. The QCLK provides the timing for the A/D converter state machine which controls the timing of the conversion. The QCLK is also the input to a 17-stage binary divider which implements the periodic/interval timer. To retain the specified analog conversion accuracy, the QCLK frequency (fQCLK) must be within the tolerance specified in Section 22. Electrical Specifications. Before using the QADC, the software must initialize the prescaler with values that put the QCLK within the specified range. Though most software applications initialize the prescaler once and do not change it, write operations to the prescaler fields are permitted. NOTE: For software compatibility with earlier versions of QADC, the definition of PSL, PSH, and PSA have been maintained. However, the requirements on minimum time and minimum low time no longer exist. CAUTION: A change in the prescaler value while a conversion is in progress is likely to corrupt the result from any conversion in progress. Therefore, any prescaler write operation should be done only when both queues are in the disabled modes. Technical Data 476 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Digital Control ZERO DETECT [5] SYSTEM CLOCK (fsys) LOAD PSH 5-BIT DOWN COUNTER CLOCK GENERATE Freescale Semiconductor, Inc... HIGH-TIME CYCLES (PSH) [5] QCLK fsys /2 to fsys/40 [3] ONE'S COMPLEMENT COMPARE SET QCLK LOW-TIME CYCLES (PSL) [3] SAR CONTROL INPUT SAMPLE TIME FROM CCW [2] ATD CONVERTER STATE MACHINE SAR [10] BINARY COUNTER 27 28 29 210 211 212 213 214 215 216 217 QUEUE1 AND QUEUE2 TIMER MODE RATE SELECTION [8] PERIODIC TIMER/INTERVAL TIMER SELECT PERIODIC/INTERVAL TRIGGER EVENT FOR Q1 AND Q2 [2] Figure 18-42. QADC Clock Subsystem Functions To accommodate wide variations of the main MCU clock frequency (IPbus system clock - fsys), QCLK is generated by a programmable prescaler which divides the MCU system clock. To allow the A/D conversion time to be maximized across the spectrum of system clock frequencies, the QADC prescaler permits the frequency of QCLK to be software selectable. It also allows the duty cycle of the QCLK waveform to be programmable. The software establishes the basic high phase of the QCLK waveform with the PSH (prescaler clock high time) field in QACR0 and selects the basic low phase of QCLK with the PSL (prescaler clock low time) field. The combination of the PSH and PSL parameters establishes the frequency of the QCLK. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 477 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) NOTE: The guideline for selecting PSH and PSL is to maintain approximately 50 percent duty cycle; for prescaler values less than 16 or PSH ~=PSL. For prescaler values greater than 16, keep PSL as large as possible. Freescale Semiconductor, Inc... Figure 18-42 shows that the prescaler is essentially a variable pulse width signal generator. A 5-bit down counter, clocked at the system clock rate, is used to create both the high phase and the low phase of the QCLK signal. At the beginning of the high phase, the 5-bit counter is loaded with the 5-bit PSH value. When the 0 detector finds that the high phase is finished, the QCLK is reset. A 3-bit comparator looks for a one's complement match with the 3-bit PSL value, which is the end of the low phase of the QCLK. These equations define QCLK frequency: high QCLK time = (PSH + 1) / fsys low QCLK time = (PSL + 1) / fsys fQCLK = 1 / (high QCLK time + low QCLK time) Where: PSH = 0 to 31, the prescaler QCLK high cycles in QACR0 PSL = 0 to 7, the prescaler QCLK low cycles in QACR0 fsys = system clock frequency fQCLK = QCLK frequency These are equations for calculating the QCLK high and low phases in example 1: high QCLK time = (11 + 1) / 40 x 106 = 300 ns low QCLK time = (7 + 1) / 40 x 106 = 200 ns fQCLK = 1/(300 + 200) = 2 MHz These are equations for calculating the QCLK high and low phases in example 2: high QCLK time = (7 + 1) / 32 x 106 = 250 ns low QCLK time = (7 + 1) / 32 x 106 = 250 ns fQCLK = 1/(250 + 250) = 2 MHz Technical Data 478 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Digital Control Figure 18-43 and Table 18-15 show examples of QCLK programmability. The examples include conversion times based on this assumption: Input sample time is as fast as possible (IST = 0, 2 QCLK cycles). Freescale Semiconductor, Inc... Figure 18-43 and Table 18-15 also show the conversion time calculated for a single conversion in a queue. For other MCU system clock frequencies and other input sample times, the same calculations can be made. SYSTEM CLOCK (fsys) QCLK EXAMPLE 1 QCLK EXAMPLE 2 20 CYCLES Figure 18-43. QADC Clock Programmability Examples Table 18-15. QADC Clock Programmability Input Sample Time IST = Binary 00 Control Register 0 Information NOTE: Example Number Frequency PSH PSL QCLK (MHz) Conversion Time (s) 1 40 MHz 11 7 2.0 7.0 2 32 MHz 7 7 2.0 7.0 PSA is maintained for software compatibility but has no functional benefit to this version of the module. The MCU system clock frequency is the basis of the QADC timing. The QADC requires that the system clock frequency be at least twice the QCLK frequency. The QCLK frequency is established by the combination of the PSH and PSL parameters in QACR0. The 5-bit PSH field selects the number of system clock cycles in the high phase of the QCLK wave. The 3-bit PSL field selects the number of system clock cycles in the low phase of the QCLK wave. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 479 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Example 1 in Figure 18-43 shows that when PSH = 11, the QCLK remains high for 12 cycles of the system clock. It also shows that when PSL = 7, the QCLK remains low for eight system clock cycles. In Example 2, PSH = 7, and the QCLK remains high for eight cycles of the system clock. It also shows that when PSL = 7, the QCLK remains low for eight system clock cycles. 18.10.9 Periodic/Interval Timer Freescale Semiconductor, Inc... The on-chip periodic/interval timer can be used to generate trigger events at a programmable interval, initiating execution of queue 1 and/or queue 2. The periodic/interval timer stays reset under these conditions: NOTE: * Both queue 1 and queue 2 are programmed to any mode which does not use the periodic/interval timer. * IPbus system reset is asserted. * Stop mode is selected. * Debug mode is selected. Interval timer single-scan mode does not use the periodic/interval timer until the single-scan enable bit is set. These conditions will cause a pulsed reset of the periodic/interval timer during use: * A queue 1 operating mode change to a mode which uses the periodic/interval timer, even if queue 2 is already using the timer * A queue 2 operating mode change to a mode which uses the periodic/interval timer, provided queue 1 is not in a mode which uses the periodic/interval timer * Roll over of the timer During the low-power stop mode, the periodic/interval timer is held in reset. Since low-power stop mode causes QACR1 and QACR2 to be reset to 0, a valid periodic or interval timer mode must be written after stop mode is exited to release the timer from reset. When the IPbus internal FREEZE line is asserted and a periodic or interval timer mode is selected, the timer counter is reset after the conversion in progress completes. When the periodic or interval timer Technical Data 480 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Digital Control mode has been enabled (the timer is counting), but a trigger event has not been issued, the debug mode takes effect immediately, and the timer is held in reset. When the internal FREEZE line is negated, the timer counter starts counting from the beginning. Refer to 18.5.1 Debug Mode for more information. 18.10.10 Conversion Command Word Table Freescale Semiconductor, Inc... The conversion command word (CCW) table is a RAM, 64 words long on 16-bit address boundaries where 10 bits of each entry are implemented. A CCW can be programmed by the software to request a conversion of one analog input channel. The CCW table is written by software and is not modified by the QADC. Each CCW requests the conversion of an analog channel to a digital result. The CCW specifies the analog channel number, the input sample time, and whether the queue is to pause after the current CCW. The 10 implemented bits of the CCW word are read/write data, where they may be written when the software initializes the QADC. The remaining six bits are unimplemented so these read as 0s, and write operations have no effect. Each location in the CCW table corresponds to a location in the result word table. When a conversion is completed for a CCW entry, the 10-bit result is written in the corresponding result word entry. The QADC provides 64 CCW table entries. The beginning of queue 1 is the first location in the CCW table. The first location of queue 2 is specified by the beginning of queue 2 pointer (BQ2) in QACR2. To dedicate the entire CCW table to queue 1, queue 2 is programmed to be in the disabled mode, and BQ2 is programmed to 64 or greater. To dedicate the entire CCW table to queue 2, queue 1 is programmed to be in the disabled mode, and BQ2 is specified as the first location in the CCW table. Figure 18-44 illustrates the operation of the queue structure. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 481 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) CONVERSION COMMAND WORD (CCW) TABLE 00 RESULT WORD TABLE BEGINNING OF QUEUE 1 00 * * * * * * CHANNEL SELECT, SAMPLE, HOLD, A/D CONVERSION END OF QUEUE 1 Freescale Semiconductor, Inc... BEGINNING OF QUEUE 2 63 * * * * * * 63 END OF QUEUE 2 10-BIT RESULT, READABLE IN THREE 16-BIT FORMATS 10-BIT CONVERSION COMMAND WORD FORMAT 9 8 [7:6] [5:0] 15 14 13 12 11 10 [9:0] P BYP IST CHAN 0 0 0 0 0 0 RESULT RIGHT-JUSTIFIED, UNSIGNED RESULT P -- PAUSE AFTER CONVERSION UNTIL NEXT TRIGGER BYP -- BYPASS BUFFER AMPLIFIER IST -- INPUT SAMPLE TIME CHAN -- CHANNEL NUMBER AND END-OF-QUEUE CODE [15:6] S RESULT [5:0] 0 0 0 0 0 0 LEFT-JUSTIFIED, SIGNED RESULT [15:6] [5:0] RESULT 0 0 0 0 0 0 LEFT-JUSTIFIED, UNSIGNED RESULT Figure 18-44. QADC Conversion Queue Operation To prepare the QADC for a scan sequence, the software writes to the CCW table to specify the desired channel conversions. The software also establishes the criteria for initiating the queue execution by programming the queue operating mode. The queue operating mode determines what type of trigger event causes queue execution to begin. A trigger event refers to any of the ways to cause the QADC to begin executing the CCWs in a queue or subqueue. An external trigger is only one of the possible trigger events. A scan sequence may be initiated by: * A software command * Expiration of the periodic/interval timer * External trigger signal * External gated signal (queue 1 only) Technical Data 482 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Digital Control The software also specifies whether the QADC is to perform a single pass through the queue or is to scan continuously. When a single-scan mode is selected, the software selects the queue operating mode and sets the single-scan enable bit. When a continuous-scan mode is selected, the queue remains active in the selected queue operating mode after the QADC completes each queue scan sequence. Freescale Semiconductor, Inc... During queue execution, the QADC reads each CCW from the active queue and executes conversions in four stages: * Initial sample * Final sample * Resolution During initial sample, a buffered version of the selected input channel is connected to the sample capacitor at the input of the sample buffer amplifier. During the final sample period, the sample buffer amplifier is bypassed, and the multiplexer input charges the sample capacitor directly. Each CCW specifies a final input sample time of 2, 4, 8, or 16 QCLK cycles. When an analog-to-digital conversion is complete, the result is written to the corresponding location in the result word table. The QADC continues to sequentially execute each CCW in the queue until the end of the queue is detected or a pause bit is found in a CCW. When the pause bit is set in the current CCW, the QADC stops execution of the queue until a new trigger event occurs. The pause status flag bit is set, which may cause an interrupt to notify the software that the queue has reached the pause state. After the trigger event occurs, the paused state ends and the QADC continues to execute each CCW in the queue until another pause is encountered or the end of the queue is detected. The end-of-queue condition is indicated by: * The CCW channel field is programmed with 63 ($3F) to specify the end of the queue. * The end-of-queue 1 is implied by the beginning of queue 2, which is specified in the BQ2 field in QACR2. * The physical end of the queue RAM space defines the end of either queue. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 483 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Freescale Semiconductor, Inc... When any of the end-of-queue conditions is recognized, a queue completion flag is set, and if enabled, an interrupt is issued to the software. These situations prematurely terminate queue execution: * Since queue 1 is higher in priority than queue 2, when a trigger event occurs on queue 1 during queue 2 execution, the execution of queue 2 is suspended by aborting the execution of the CCW in progress, and the queue 1 execution begins. When queue 1 execution is completed, queue 2 conversions restart with the first CCW entry in queue 2 or the first CCW of the queue 2 subqueue being executed when queue 2 was suspended. Alternately, conversions can restart with the aborted queue 2 CCW entry. The RESUME bit in QACR2 allows the software to select where queue 2 begins after suspension. By choosing to re-execute all of the suspended queue 2 queue and subqueue CCWs, all of the samples are guaranteed to have been taken during the same scan pass. However, a high trigger event rate for queue 1 can prohibit the completion of queue 2. If this occurs, the software may choose to begin execution of queue 2 with the aborted CCW entry. * Software can change the queue operating mode to disabled mode. Any conversion in progress for that queue is aborted. Putting a queue into the disabled mode does not power down the converter. * Software can change the queue operating mode to another valid mode. Any conversion in progress for that queue is aborted. The queue restarts at the beginning of the queue, once an appropriate trigger event occurs. * For low-power operation, software can set the stop mode bit to prepare the module for a loss of clocks. The QADC aborts any conversion in progress when the stop mode is entered. * When the freeze enable bit is set by software and the IPbus internal FREEZE line is asserted, the QADC freezes at the end of the conversion in progress. When internal FREEZE is negated, the QADC resumes queue execution beginning with the next CCW entry. Refer to 18.5.1 Debug Mode for more information. Technical Data 484 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Digital Control 18.10.11 Result Word Table The result word table is a RAM, 64 words long and 10 bits wide. An entry is written by the QADC after completing an analog conversion specified by the corresponding CCW table entry. Software can read or write the result word table, but in normal operation, the software reads the result word table to obtain analog conversions from the QADC. Unimplemented bits are read as 0s, and write operations do not have any effect. Freescale Semiconductor, Inc... While there is only one result word table, the data can be accessed in three different data formats: * Right justified in the 16-bit word, with 0s in the higher order unused bits * Left justified, with the most significant bit inverted to form a sign bit, and 0s in the unused lower order bits * Left justified, with 0s in the lower order unused bits The left justified, signed format corresponds to a half-scale, offset binary, two's complement data format. The data is routed onto the IPbus according to the selected format. The address used to access the table determines the data alignment format. All write operations to the result word table are right justified. The three result data formats are produced by routing the RAM bits onto the data bus. The software chooses among the three formats by reading the result at the memory address which produces the desired data alignment. The result word table is read/write accessible by software. During normal operation, applications software only needs to read the result table. Write operations to the table may occur during test or debug breakpoint operation. When locations in the CCW table are not used by an application, software could use the corresponding locations in the result word table as scratch pad RAM, remembering that only 10 bits are implemented. The result alignment is only implemented for software read operations. Since write operations are not the normal use for the result registers, only one write data format is supported, which is right justified data. NOTE: Some write operations, like bit manipulation, may not operate as expected because the hardware cannot access a true 16-bit value. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 485 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) 18.11 Pin Connection Considerations The QADC requires accurate, noise-free input signals for proper operation. This section discusses the design of external circuitry to maximize QADC performance. Freescale Semiconductor, Inc... 18.11.1 Analog Reference Pins No A/D converter can be more accurate than its analog reference. Any noise in the reference can result in at least that much error in a conversion. The reference for the QADC, supplied by pins VRH and VRL, should be low-pass filtered from its source to obtain a noise-free, clean signal. In many cases, simple capacitive bypassing may suffice. In extreme cases, inductors or ferrite beads may be necessary if noise or RF energy is present. Series resistance is not advisable since there is an effective dc current requirement from the reference voltage by the internal resistor string in the RC DAC array. External resistance may introduce error in this architecture under certain conditions. Any series devices in the filter network should contain a minimum amount of DC resistance. For accurate conversion results, the analog reference voltages must be within the limits defined by VDDA and VSSA, as explained in this subsection. 18.11.2 Analog Power Pins The analog supply pins (VDDA and VSSA) define the limits of the analog reference voltages (VRH and VRL) and of the analog multiplexer inputs. Figure 18-45 is a diagram of the analog input circuitry. Since the sample amplifier is powered by VDDA and VSSA, it can accurately transfer input signal levels up to but not exceeding VDDA and down to but not below VSSA. If the input signal is outside of this range, the output from the sample amplifier is clipped. In addition, VRH and VRL must be within the range defined by VDDA and VSSA. As long as VRH is less than or equal to VDDA and VRL is greater than or equal to VSSA and the sample amplifier has accurately transferred the input signal, resolution is ratiometric within the limits Technical Data 486 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Pin Connection Considerations VDDA VRH SAMPLE AMP S/H RC DAC COMPARATOR Freescale Semiconductor, Inc... 16 CHANNELS TOTAL CP V SSA VRL Figure 18-45. Equivalent Analog Input Circuitry defined by VRL and VRH. If VRH is greater than VDDA, the sample amplifier can never transfer a full-scale value. If VRL is less than VSSA, the sample amplifier can never transfer a 0 value. In addition, VRH and VRL must be within the range defined by VDDA and VSSA. As long as VRH is less than or equal to VDDA and VRL is greater than or equal to VSSA and the sample amplifier has accurately transferred the input signal, resolution is ratiometric within the limits defined by VRL and VRH. If VRH is greater than VDDA, the sample amplifier can never transfer a full-scale value. If VRL is less than VSSA, the sample amplifier can never transfer a 0 value. Figure 18-46 shows the results of reference voltages outside the range defined by VDDA and VSSA. At the top of the input signal range, VDDA is 10 mV lower than VRH. This results in a maximum obtainable 10-bit conversion value of $3FE. At the bottom of the signal range, VSSA is 15 mV higher than VRL, resulting in a minimum obtainable 10-bit conversion value of three. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 487 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) 3FF 10-BIT RESULT (HEXADECIMAL) Freescale Semiconductor, Inc... 3FE 3FD 3FC 3FB 3FA 8 7 6 5 4 3 2 1 0 .010 .020 .030 5.100 5.110 5.120 5.130 INPUTS IN VOLTS (VRH = 5.120 V, VRL = 0 V) Figure 18-46. Errors Resulting from Clipping 18.11.3 Conversion Timing Schemes This section contains some conversion timing examples. Figure 18-47 shows the timing for basic conversions where it is assumed that: * Q1 begins with CCW0 and ends with CCW3. * CCW0 has pause bit set. * CCW1 does not have pause bit set. * External trigger rise edge for Q1. * CCW4 = BQ2 and Q2 is disabled. * Q1 Res shows relative result register updates. Recall that when QS = 0, both queues are disabled, when QS = 8, queue 1 is active and queue 2 is idle, and when QS = 4, queue 1 is paused and queue 2 is disabled. Technical Data 488 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Pin Connection Considerations TIME BETWEEN TRIGGERS CONVERSION TIME S 14 QCLKS CONVERSION TIME S 14 QCLKS QCLK TRIG1 Freescale Semiconductor, Inc... EOC QS CWP 8 0 LAST CWPQ1 Q1 RES 4 8 CCW0 LAST CCW1 CCW2 CCW0 CCW1 R0 R1 Figure 18-47. External Positive Edge Trigger Mode Timing With Pause A time separator is provided between the triggers and the end of conversion (EOC). The relationship to QCLK displayed is not guaranteed. CWPQ1 and CWPQ2 typically lag CWP and only match CWP when the associated queue is inactive. Another way to view CWPQ1(2) is that these registers update when EOC triggers the result register to be written. In the case with the pause bit set (CCW0), CWP does not increment until triggered. In the case with the pause bit clear (CCW1), the CWP increments with the EOC. The conversion results Q1 Res(x) show the result associated with CCW(x). So that R0 represents the result associated with CCW0. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 489 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Figure 18-48 shows the timing for conversions in gated mode single scan with same assumptions in example 1 except: * No pause bits set in any CCW * External trigger gated mode single scan for Q1 * Single scan bit is set. Freescale Semiconductor, Inc... When the gate closes and opens again, the conversions start with the first CCW in Q1. When the gate closes, the active conversion completes before the queue goes idle. When Q1 completes both the CF1 bit sets and the SSE bit clears. A proposed amended definition for the PF bit in this mode, to reflect the condition that a gate closing occurred before the queue completed, is under consideration. Figure 18-49 shows the timing for conversions in gated mode continuous scan with the same assumptions as in Figure 18-48. At the end of Q1,the completion flag CF1 sets and the queue restarts. If the queue starts a second time and completes, the trigger overrun flag TOR1 sets. 18.11.4 Analog Supply Filtering and Grounding Two important factors influencing performance in analog integrated circuits are supply filtering and grounding. Generally, digital circuits use bypass capacitors on every VDD/VSS pin pair. This applies to analog subsystems or submodules also. Equally important as bypassing is the distribution of power and ground. Technical Data 490 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Pin Connection Considerations TRIG1 (GATE) EOC QS 0 Freescale Semiconductor, Inc... CWP 8 LAST 0 CCW0 8 CCW1 CCW0 0 CCW1 CCW2 CCW3 CWPQ1 LAST CCW0 CCW1 CCW0 CCW1 CCW2 CCW3 Q1 RES LAST R0 R1 R0 R1 R2 R3 SSE SOFTWARE MUST SET SSE. CF1 SOFTWARE MUST CLEAR PF1. PF1 Figure 18-48. Gated Mode, Single Scan Timing TRIG1 (GATE) EOC QS CWP 0 8 LAST CCW0 CCW1 CCW2 CCW3 CCW0 CCW3 CCW0 CSPQ1 LAST CCW0 CCW1 CCW2 CCW3 CCW2 CCW3 Q1 RES LAST XX R0 R1 R2 R3 R2 R3 CF1 TOR1 QUEUE RESTART QUEUE RESTART Figure 18-49. Gated Mode, Continuous Scan Timing MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 491 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Freescale Semiconductor, Inc... Analog supplies should be isolated from digital supplies as much as possible. This necessity stems from the higher performance requirements often associated with analog circuits. Therefore, deriving an analog supply from a local digital supply is not recommended. However, if for economic reasons digital and analog power are derived from a common regulator, filtering of the analog power is recommended in addition to the bypassing of the supplies already mentioned. For example, an RC low pass filter could be used to isolate the digital and analog supplies when generated by a common regulator. If multiple high precision analog circuits are locally employed (for example, two A/D converters), the analog supplies should be isolated from each other as sharing supplies introduces the potential for interference between analog circuits. Grounding is the most important factor influencing analog circuit performance in mixed signal systems (or in standalone analog systems). Close attention must be paid not to introduce additional sources of noise into the analog circuitry. Common sources of noise include ground loops, inductive coupling, and combining digital and analog grounds together inappropriately. The problem of how and when to combine digital and analog grounds arises from the large transients which the digital ground must handle. If the digital ground is not able to handle the large transients, the current from the large transients can return to ground through the analog ground. It is the excess current overflowing into the analog ground which causes performance degradation by developing a differential voltage between the true analog ground and the microcontroller's ground pin. The end result is that the ground observed by the analog circuit is no longer true ground and often ends in skewed results. Two similar approaches designed to improve or eliminate the problems associated with grounding excess transient currents involve star-point ground systems. One approach is to star-point the different grounds at the power supply origin, thus keeping the ground isolated. Refer to Figure 18-50. Another approach is to star-point the different grounds near the analog ground pin on the microcontroller by using small traces for connecting the non-analog grounds to the analog ground. The small traces are meant only to accommodate dc differences, not ac transients. Technical Data 492 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Pin Connection Considerations NOTE: This star-point scheme still requires adequate grounding for digital and analog subsystems in addition to the star-point ground. ANALOG POWER SUPPLY +5 V PGND +5 V VDDA VSSA AGND VRL VRH Freescale Semiconductor, Inc... +5 V DIGITAL POWER SUPPLY VSS QADC VDD PCB Figure 18-50. Star-Ground at the Point of Power Supply Origin Other suggestions for PCB layout in which the QADC is employed include: * Analog ground must be low impedance to all analog ground points in the circuit. * Bypass capacitors should be as close to the power pins as possible. * The analog ground should be isolated from the digital ground. This can be done by cutting a separate ground plane for the analog ground. * Non-minimum traces should be utilized for connecting bypass capacitors and filters to their corresponding ground/power points. * Minimum distance for trace runs when possible. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 493 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) 18.11.5 Accommodating Positive/Negative Stress Conditions Freescale Semiconductor, Inc... Positive or negative stress refers to conditions which exceed nominally defined operating limits. Examples include applying a voltage exceeding the normal limit on an input (for example, voltages outside of the suggested supply/reference ranges) or causing currents into or out of the pin which exceed normal limits. QADC specific considerations are voltages greater than VDDA, VRH, or less than VSSA applied to an analog input which cause excessive currents into or out of the input. Refer to Section 22. Electrical Specifications for more information on exact magnitudes. Either stress conditions can potentially disrupt conversion results on neighboring inputs. Parasitic devices, associated with CMOS processes, can cause an immediate disruptive influence on neighboring pins. Common examples of parasitic devices are diodes to substrate and bipolar devices with the base terminal tied to substrate (VSSI/VSSA ground). Under stress conditions, current injected on an adjacent pin can cause errors on the selected channel by developing a voltage drop across the selected channel's impedances. Figure 18-51 shows an active parasitic bipolar NPN transistor when an input pin is subjected to negative stress conditions. Figure 18-52 shows positive stress conditions can activate a similar PNP transistor. VStress + IINJN RStress 10 K IIn RSelected ANn PIN UNDER STRESS PARASITIC DEVICE ADJACENT PIN ANn+1 VIn Figure 18-51. Input Pin Subjected to Negative Stress VStress + RStress 10 K RSelected VIn IINJP IIn ANn PIN UNDER STRESS VDDA PARASITIC DEVICE ANn+1 ADJACENT PIN Figure 18-52. Input Pin Subjected to Positive Stress Technical Data 494 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Pin Connection Considerations The current into the pin (IINJN or IINJP) under negative or positive stress is determined by these equations: -( V -V ) Stress BE I INJN = ----------------------------------------------R Stress V -V -V Stress EB DDA I INJP = --------------------------------------------------------------R Stress Freescale Semiconductor, Inc... where: VStress = Adjustable voltage source VEB = Parasitic PNP emitter/base voltage VBE = Parasitic NPN base/emitter voltage RStress = Source impedance (10 K resistor in Figure 18-51 and Figure 18-52 on stressed channel) = Source impedance on channel selected for conversion RSelected The current into (IIn) the neighboring pin is determined by the KN (current coupling ratio) of the parasitic bipolar transistor (KN 1). The IIn can be expressed by this equation: IIn = - KN * IINJ where: IINJ is either IINJN or IINJP. A method for minimizing the impact of stress conditions on the QADC is to strategically allocate QADC inputs so that the lower accuracy inputs are adjacent to the inputs most likely to see stress conditions. Also, suitable source impedances should be selected to meet design goals and minimize the effect of stress conditions. 18.11.6 Analog Input Considerations The source impedance of the analog signal to be measured and any intermediate filtering should be considered whether external multiplexing is used or not. Figure 18-53 shows the connection of eight typical analog signal sources to one QADC analog input pin through a separate multiplexer chip. Also, an example of an analog signal source connected directly to a QADC analog input channel is displayed. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 495 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) ANALOG SIGNAL SOURCE R Source2 FILTERING AND INTERCONNECT R Filter2 TYPICAL MUX CHIP (MC54HC4051, MC74HC4051, MC54HC4052, MC74HC4052, MC54HC4053, ETC.) INTERCONNECT QADC ~ 0.01 mF1 C Source R Source2 R Filter2 C Filter C MUXIN ~ 0.01 mF1 C Source Freescale Semiconductor, Inc... R Source2 R Filter2 C Filter C MUXIN ~ R MUXOUT 0.01 mF1 C Source R Source2 R Filter2 C Filter C MUXIN ~ C MUXOUT 0.01 mF1 C Source R Source2 R Filter2 C Filter C PCB C MUXIN CP C SAMP CIn = CP + CSAMP ~ 0.01 mF1 C Source R Source2 R Filter2 C Filter C MUXIN ~ 0.01 mF1 C Source R Source2 R Filter2 C Filter C MUXIN ~ 0.01 mF1 C Source R Source2 R Filter2 C Filter C MUXIN ~ 0.01 mF1 C Source R Source2 C Filter C MUXIN R Filter2 ~ 0.01 mF1 C Source C Filter Notes: 1. Typical value 2. RFilter Typically 10 K-20 K. C PCB CP C SAMP Figure 18-53. External Multiplexing of Analog Signal Sources Technical Data 496 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Pin Connection Considerations 18.11.7 Analog Input Pins Freescale Semiconductor, Inc... Analog inputs should have low ac impedance at the pins. Low ac impedance can be realized by placing a capacitor with good high frequency characteristics at the input pin of the part. Ideally, that capacitor should be as large as possible (within the practical range of capacitors that still have good high-frequency characteristics). This capacitor has two effects: * It helps attenuate any noise that may exist on the input. * It sources charge during the sample period when the analog signal source is a high-impedance source. Series resistance can be used with the capacitor on an input pin to implement a simple RC filter. The maximum level of filtering at the input pins is application dependent and is based on the bandpass characteristics required to accurately track the dynamic characteristics of an input. Simple RC filtering at the pin may be limited by the source impedance of the transducer or circuit supplying the analog signal to be measured. (See 18.11.7.2 Error Resulting from Leakage). In some cases, the size of the capacitor at the pin may be very small. Figure 18-54 is a simplified model of an input channel. Refer to this model in the following discussion of the interaction between the external circuitry and the circuitry inside the QADC. SOURCE EXTERNAL FILTER RSRC INTERNAL CIRCUIT MODEL S1 S2 S3 RF AMP CSAMP VSRC CF V SRC = Source voltage RSRC = Source impedance RF = Filter impedance CF = Filter capacitor CP VI CP = Internal parasitic capacitance CSAMP= Sample capacitor VI = Internal voltage source during sample and hold Figure 18-54. Electrical Model of an A/D Input Pin MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 497 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) In Figure 18-54, RF, RSRC and CF comprise the external filter circuit. CP is the internal parasitic capacitor. CSamp is the capacitor array used to sample and hold the input voltage. VI is an internal voltage source used to provide charge to Csamp during sample phase. Freescale Semiconductor, Inc... The following paragraphs provide a simplified description of the interaction between the QADC and the user's external circuitry. This circuitry is assumed to be a simple RC low-pass filter passing a signal from a source to the QADC input pin. These simplifying assumptions are made: * The external capacitor is perfect (no leakage, no significant dielectric absorption characteristics, etc.) * All parasitic capacitance associated with the input pin is included in the value of the external capacitor. * Inductance is ignored. * The "on" resistance of the internal switches is 0 ohms and the "off" resistance is infinite. 18.11.7.1 Settling Time for the External Circuit The values for RSRC, RF, and CF in the user's external circuitry determine the length of time required to charge CF to the source voltage level (VSRC). At time t = 0, Vsrc changes in Figure 18-54 while S1 is open, disconnecting the internal circuitry from the external circuitry. Assume that the initial voltage across CF is 0. As CF charges, the voltage across it is determined by the equation, where t is the total charge time: VCF = VSRC (1 -e-t/(RF + RSRC) CF) As t approaches infinity, VCF will equal VSRC. (This assumes no internal leakage.) With 10-bit resolution, 1/2 of a count is equal to 1/2048 full-scale value. Assuming worst case (VSRC = full scale), Table 18-16 shows the required time for CF to charge to within 1/2 of a count of the actual source voltage during 10-bit conversions. Table 18-16 is based on the RC network in Figure 18-54. NOTE: The following times are completely independent of the A/D converter architecture (assuming the QADC is not affecting the charging). Technical Data 498 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Pin Connection Considerations Table 18-16. External Circuit Settling Time to 1/2 LSB (10-Bit Conversions) Freescale Semiconductor, Inc... Filter Capacitor (CF) Source Resistance (RF + RSRC) 100 1 k 10 k 100 k 1 F 760 s 7.6 ms 76 ms 760 ms 0.1 F 76 s 760 s 7.6 ms 76 ms 0.01 F 7.6 s 76 s 760 s 7.6 ms 0.001 F 760 ns 7.6 s 76 s 760 s 100 pF 76 ns 760 ns 7.6 s 76 s The external circuit described in Table 18-16 is a low-pass filter. A user interested in measuring an ac component of the external signal must take the characteristics of this filter into account. 18.11.7.2 Error Resulting from Leakage A series resistor limits the current to a pin therefore, input leakage acting through a large source impedance can degrade A/D accuracy. The maximum input leakage current is specified in Section 22. Electrical Specifications. Input leakage is greater at higher operating temperatures. In the temperature range from 125C to 50C, the leakage current is halved for every 8C to 12C reduction in temperature. Assuming VRH-VRL = 5.12 V, 1 count (with 10-bit resolution) corresponds to 5 mV of input voltage. A typical input leakage of 200 nA acting through 10 k of external series resistance results in an error of 0.4 count (2.0 mV). If the source impedance is 100 k and a typical leakage of 100 nA is present, an error of 2 counts (10 mV) is introduced. In addition to internal junction leakage, external leakage (for example, if external clamping diodes are used) and charge sharing effects with internal capacitors also contribute to the total leakage current. Table 18-17 illustrates the effect of different levels of total leakage on accuracy for different values of source impedance. The error is listed in terms of 10-bit counts. CAUTION: Leakage from the part below 200 nA is obtainable only within a limited temperature range. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 499 Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Table 18-17. Error Resulting From Input Leakage (IOff) Leakage Value (10-Bit Conversions) Freescale Semiconductor, Inc... Source Impedance 100 nA 200 nA 500 nA 1000 nA 1 k -- -- 0.1 counts 0.2 counts 10 k 0.2 counts 0.4 counts 1 counts 2 counts 100 k 2 counts 4 count 10 counts 20 counts 18.12 Interrupts The four interrupt lines are outputs of the module and have no priority or arbitration within the module. 18.12.1 Interrupt Operation QADC inputs can be monitored by polling or by using interrupts. When interrupts are not needed, software can disable the pause and completion interrupts and monitor the completion flag and the pause flag for each queue in the status register (QASR). In other words, flag bits can be polled to determine when new results are available. Table 18-18 shows the status flag and interrupt enable bits which correspond to queue 1 and queue 2 activity. Table 18-18. QADC Status Flags and Interrupt Sources Queue Queue Activity Result written to last CCW in queue 1 Queue 1 Result written for a CCW with pause bit set in queue 1 Result written to last CCW in queue 2 Queue 2 Result written for a CCW with pause bit set in queue 2 Status Flag Interrupt Enable Bit CF1 CIE1 PF1 PIE1 CF2 CIE2 PF2 PIE2 If interrupts are enabled for an event, the QADC requests interrupt service when the event occurs. Using interrupts does not require continuously polling the status flags to see if an event has taken place. Technical Data 500 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Queued Analog-to-Digital Converter (QADC) Interrupts However, status flags must be cleared after an interrupt is serviced, in to disable the interrupt request Freescale Semiconductor, Inc... In both polled and interrupt-driven operating modes, status flags must be re-enabled after an event occurs. Flags are re-enabled by clearing appropriate QASR bits in a particular sequence. The register must first be read, then 0s must be written to the flags that are to be cleared. If a new event occurs between the time that the register is read and the time that it is written, the associated flag is not cleared. 18.12.2 Interrupt Sources The QADC includes four sources of interrupt requests, each of which is separately enabled. Each time the result is written for the last conversion command word (CCW) in a queue, the completion flag for the corresponding queue is set, and when enabled, an interrupt request is generated. In the same way, each time the result is written for a CCW with the pause bit set, the queue pause flag is set, and when enabled, an interrupt request is generated. Refer to Table 18-18. The pause and complete interrupts for queue 1 and queue 2 have separate interrupt vector levels, so that each source can be separately serviced. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com 501 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Queued Analog-to-Digital Converter (QADC) Technical Data 502 MMC2107 - Rev. 2.0 Queued Analog-to-Digital Converter (QADC) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 19. External Bus Interface Module (EBI) 19.1 Contents Freescale Semiconductor, Inc... 19.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 504 19.3 Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .505 19.3.1 Data Bus (D[31:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 506 19.3.2 Show Cycle Strobe (SHS) . . . . . . . . . . . . . . . . . . . . . . . . . 506 19.3.3 Transfer Acknowledge (TA) . . . . . . . . . . . . . . . . . . . . . . . . 506 19.3.4 Transfer Error Acknowledge (TEA) . . . . . . . . . . . . . . . . . .506 19.3.5 Emulation Mode Chip Selects (CSE[1:0]) . . . . . . . . . . . . . 506 19.3.6 Transfer Code (TC[2:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . . 506 19.3.7 Read/Write (R/W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507 19.3.8 Address Bus (A[22:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507 19.3.9 Enable Byte (EB[3:0]). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507 19.3.10 Chip Selects (CS[3:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507 19.3.11 Output Enable (OE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507 19.3.12 Transfer Size (TSIZ[1:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . 507 19.3.13 Processor Status (PSTAT[3:0]) . . . . . . . . . . . . . . . . . . . . . 507 19.4 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 508 19.5 Operand Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 508 19.6 Enable Byte Pins (EB[3:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . . 510 19.7 Bus Master Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 510 19.7.1 Read Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511 19.7.1.1 State 1 (X1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512 19.7.1.2 Optional Wait States (X2W) . . . . . . . . . . . . . . . . . . . . . . 512 19.7.1.3 State 2 (X2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512 19.7.2 Write Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 513 19.7.2.1 State 1 (X1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 514 19.7.2.2 Optional Wait States (X2W) . . . . . . . . . . . . . . . . . . . . . . 514 19.7.2.3 State 2 (X2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 514 MMC2107 - Rev. 2.0 MOTOROLA Technical Data External Bus Interface Module (EBI) For More Information On This Product, Go to: www.freescale.com 503 Freescale Semiconductor, Inc. External Bus Interface Module (EBI) 19.8 Bus Exception Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 516 19.8.1 Transfer Error Termination . . . . . . . . . . . . . . . . . . . . . . . . . 516 19.8.2 Transfer Abort Termination . . . . . . . . . . . . . . . . . . . . . . . . 516 19.9 Emulation Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 516 19.9.1 Emulation Chip-Selects (CSE[1:0]) . . . . . . . . . . . . . . . . . .516 19.9.2 Internal Data Transfer Display (Show Cycles) . . . . . . . . . . 517 19.9.3 Show Strobe (SHS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 518 19.10 Bus Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 519 Freescale Semiconductor, Inc... 19.11 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 520 19.2 Introduction The external bus interface (EBI) module is responsible for controlling the transfer of information between the internal M*CORE local bus and external address space. The external bus has 23 address lines and 32 data lines. In master mode and emulation mode, the EBI functions as a bus master and allows internal bus cycles to access external resources. In single-chip mode, the EBI is active, but the external data bus is not available, and no external data or termination signals are transferred to the internal bus. The EBI supports data transfers to both 32-bit and 16-bit ports. Chip-select channels are programmed to define the port size for specific address ranges. When no chip-select is active during an external data transfer, the port size is assumed to be 32 bits. The EBI supports a variable length external bus cycle to accommodate the access speed of any device. During an external data transfer, the EBI drives the address pins, byte enable pins, output enable pins, size pins, and read/write pins. Wait states are inserted until the bus cycle is terminated by the assertion of the internal transfer acknowledge signal by a chip-select channel or by the assertion of the external TA or TEA pins. The minimum external bus cycle is one clock. Technical Data 504 MMC2107 - Rev. 2.0 External Bus Interface Module (EBI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. External Bus Interface Module (EBI) Signal Descriptions The EBI also drives the address, size, and read/write pins during internal data transfers, but the output enable and byte enable pins are not asserted. To see the internal data bus on the external pins, show cycles must be enabled. Freescale Semiconductor, Inc... Only internal sources can terminate internal data transfers. Chip-select channels, external TA assertion, and external TEA assertion cannot terminate internal data transfers. 19.3 Signal Descriptions Table 19-1 provides an overview of the signal properties which are discussed in this subsection. Table 19-1. Signal Properties Name Port Function D[31:0] PA, PB, PC, PD SHS PE7 Show cycle strobe Active TA PE6 Transfer acknowledge Active TEA PE5 Transfer error acknowledge Active CSE[1:0] PE[4:3] Emulation chip selects Active TC[2:0] PE[2:0] Transfer code Active R/W PF7 Read/write Active A[22:0] PF[6:0], PG, PH Address bus Active EB[3:0] PI[7:4] Enable byte Active CS[3:0] PI[3:0] Chip selects Active OE -- Output enable -- TSIZ[1:0] -- Transfer size -- PSTAT[3:0] -- Processor status -- Data bus MMC2107 - Rev. 2.0 MOTOROLA Pullup -- Technical Data External Bus Interface Module (EBI) For More Information On This Product, Go to: www.freescale.com 505 Freescale Semiconductor, Inc. External Bus Interface Module (EBI) 19.3.1 Data Bus (D[31:0]) The three-state bidirectional data bus (D[31:0]) signals are the general-purpose data path between the microcontroller unit (MCU) and all other devices. 19.3.2 Show Cycle Strobe (SHS) Freescale Semiconductor, Inc... In emulation mode, show cycle strobe (SHS) is the strobe for capturing address, controls, and data during show cycles. 19.3.3 Transfer Acknowledge (TA) The transfer acknowledge (TA) signal indicates that the external data transfer is complete. During a read cycle, when the processor recognizes TA, it latches the data and then terminates the bus cycle. During a write cycle, when the processor recognizes TA, the bus cycle is terminated. TA is an input in master and emulation modes. 19.3.4 Transfer Error Acknowledge (TEA) The transfer error acknowledge (TEA) indicates an error condition exists for the bus transfer. The bus cycle is terminated and the CPU begins execution of the access error exception. TEA is an input in master and emulation modes. 19.3.5 Emulation Mode Chip Selects (CSE[1:0]) The emulation mode chip selects (CSE[1:0]) output signals provide information for development support. 19.3.6 Transfer Code (TC[2:0]) The transfer code (TC[2:0]) output signals indicate the data transfer code for the current bus cycle. Technical Data 506 MMC2107 - Rev. 2.0 External Bus Interface Module (EBI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. External Bus Interface Module (EBI) Signal Descriptions 19.3.7 Read/Write (R/W) The read/write (R/W) output signal indicates the direction of the data transfer on the bus. A logic 1 indicates a read from a slave device and a logic 0 indicates a write to a slave device. 19.3.8 Address Bus (A[22:0]) Freescale Semiconductor, Inc... The address bus (A[22:0]) output signals provide the address for the current bus transfer. 19.3.9 Enable Byte (EB[3:0]) The enable byte (EB[3:0]) output signals indicate which byte of data is valid during external cycles. 19.3.10 Chip Selects (CS[3:0]) The chip selects (CS[3:0]) output signals select external devices for external bus transactions. 19.3.11 Output Enable (OE) The output enable (OE) signal indicates when an external device can drive data during external read cycles. 19.3.12 Transfer Size (TSIZ[1:0]) TSIZ[1:0] provides an indication of the M*CORE transfer size. 19.3.13 Processor Status (PSTAT[3:0]) PSTAT[3:0] provides an indication of the M*CORE processor status. MMC2107 - Rev. 2.0 MOTOROLA Technical Data External Bus Interface Module (EBI) For More Information On This Product, Go to: www.freescale.com 507 Freescale Semiconductor, Inc. External Bus Interface Module (EBI) 19.4 Memory Map and Registers The EBI is not memory-mapped and has no software-accessible registers. 19.5 Operand Transfer Freescale Semiconductor, Inc... The possible operand accesses for the internal M*CORE bus are: * Byte * Aligned upper half-word * Aligned lower half-word * Aligned word No misaligned transfers are supported. The EBI controls the byte, half-word, or word operand transfers between the M*CORE bus and a 16-bit or 32-bit port. "Port" refers to the width of the data path that an external device uses during a data transfer. Each port is assigned to particular bits of the data bus. A 16-bit port is assigned to pins D[31:16] and a 32-bit port is assigned to pins D[31:0]. In the case of a word (32-bit) access to a 16-bit port, the EBI runs two external bus cycles to complete the transfer. During the first external bus cycle, the A[1:0] pins are driven low, and the TSIZ[1:0] pins are driven to indicate word size. During the second cycle, A1 is driven high to increment the external address by two bytes, A0 is still driven low, and the TSIZ[1:0] pins are driven to indicate half-word size. During any word-size transfer, the EBI always drives the A[1:0] pins low during a word transfer (except on the second cycle of a word to half-word port transfer in which A1 is incremented). Table 19-2 shows each possible transfer size, alignment, and port width. The data bytes shown in the table represent external data pins. This data is multiplexed and driven to the external data bus as shown. The bytes labeled with a dash are not required; the M*CORE will ignore them on read transfers, and drive them with undefined data on write transfers. Technical Data 508 MMC2107 - Rev. 2.0 External Bus Interface Module (EBI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. External Bus Interface Module (EBI) Operand Transfer Table 19-2. Data Transfer Cases External Pins Transfer Port Size Width TSIZ1 TSIZ0 A1 A0 16 0 16 0 Freescale Semiconductor, Inc... 1 16 1 16 0 1 0 0 -- -- D[23:16] -- -- -- D[23:16] -- -- -- -- D[31:24] -- -- -- D[15:8] -- -- -- -- D[23:16] -- -- -- D[7:0] D[31:24] D[23:16] -- -- D[31:24] D[23:16] -- -- 0 -- -- D[31:24] D[23:16] -- -- D[15:8] D[7:0] -- -- 0 32 32 -- 0 16 1 -- 0 32 Word D[31:24] 1 32 16(1) -- 0 32 1 -- 1 16 Half-word -- 1 32 Byte D[31:24] 0 32 0 Data Bus Transfer 0 0 1 0 0 0 D[31:24] D[23:16] -- -- D[31:24] D[23:16] D[31:24] D[23:16] D[15:8] D[7:0] 1. The EBI runs two cycles for word accesses to 16-bit ports. The table shows the data placement for both bus cycles. MMC2107 - Rev. 2.0 MOTOROLA Technical Data External Bus Interface Module (EBI) For More Information On This Product, Go to: www.freescale.com 509 Freescale Semiconductor, Inc. External Bus Interface Module (EBI) 19.6 Enable Byte Pins (EB[3:0]) The enable byte pins (EB[3:0]) are configurable as byte enables for read and write cycles, or as write enables for write cycles only. The default function is byte enable unless there is an active chip-select match with the WE bit set. In all external cycles when one or more EB pins are asserted, the encoding corresponds to the external data pins to be used for the transfer as outlined in Table 19-3. Freescale Semiconductor, Inc... Table 19-3. EB[3:0] Assertion Encoding EB Pin External Data Pins EB0 D[31:24] EB1 D[23:16] EB2 D[15:8] EB3 D[7:0] 19.7 Bus Master Cycles In this subsection, each EBI bus cycle type is defined in terms of actions associated with a succession of internal states. These internal states are only for reference and may not correspond to any implemented machine states. Read or write operations may require multiple bus cycles to complete based on the operand size and target port size. Refer to 19.5 Operand Transfer for more information. In the discussion that follows, it is assumed that only a single bus cycle is required for a transfer. In the waveform diagrams (Figure 19-3 through Figure 19-6), data transfers are related to clock cycles, independent of the clock frequency. The external bus states are also noted. Technical Data 510 MMC2107 - Rev. 2.0 External Bus Interface Module (EBI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. External Bus Interface Module (EBI) Bus Master Cycles 19.7.1 Read Cycles During a read cycle, the EBI receives data from an external memory or peripheral device. During external read cycles, the OE pin is asserted regardless of operand size. See Figure 19-1. MMC2107 EXTERNAL PERIPHERAL Freescale Semiconductor, Inc... ADDRESS DEVICE 1. SET R/W TO READ. 2. DRIVE ADDRESS ON A[22:0]. 3. DRIVE TSIZ[1:0] PINS FOR OPERAND SIZE. 4. ASSERT CS IF USED. 5. ASSERT OE AND EB IF USED. PRESENT DATA 1. RECEIVE CS. 2. DECODE ADDRESS. 3. ASSERT TA IF NECESSARY FROM SLAVE DEVICE. 4. PUT DATA ON D[31:16] AND/OR D[15:0]. ACQUIRE DATA 1. RECEIVE DATA FROM D[31:16] AND/OR D[15:0]. 2. DRIVE DATA TO INTERNAL DATA BUS. 3. NEGATE OE AND EB. TERMINATE CYCLE 1. REMOVE DATA FROM D[31:16] AND/OR D[15:0]. 2. NEGATE TA. START NEXT CYCLE 1. NEGATE EB AND CS IF USED. Figure 19-1. Read Cycle Flowchart MMC2107 - Rev. 2.0 MOTOROLA Technical Data External Bus Interface Module (EBI) For More Information On This Product, Go to: www.freescale.com 511 Freescale Semiconductor, Inc. External Bus Interface Module (EBI) 19.7.1.1 State 1 (X1) The EBI drives the address bus. R/W is driven high to indicate a read cycle. The TSIZ[1:0] pins are driven to indicate the number of bytes in the transfer. TC[2:0] pins are driven to indicate the type of access. CS may be asserted to drive a device. Freescale Semiconductor, Inc... Later in state 1, OE is asserted. If the EB pins are not configured as write enables for this cycle, one or more EB pins are also asserted, depending on the size and position of the data to be transferred. If either the external TA pin or internal chip-select transfer acknowledge signal is asserted before the end of state 1, the EBI proceeds to state 2. 19.7.1.2 Optional Wait States (X2W) Wait states are inserted until the slave asserts the TA pin or the internal chip-select transfer acknowledge signal is asserted. Wait states are counted in full clocks. 19.7.1.3 State 2 (X2) One-half clock later in state 2, the selected device puts its information on D[31:16] and/or D[15:0]. One or both half-words of the external data bus are driven to the internal data bus. The address bus, R/W, CS, OE, EB, TC, and TSIZ pins remain valid through state 2 to allow for static memory operation and signal skew. The slave device asserts data until it detects the negation of OE, after which it and must remove its data within approximately one-half of a state. Note that the data bus may not become free until state 1. Technical Data 512 MMC2107 - Rev. 2.0 External Bus Interface Module (EBI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. External Bus Interface Module (EBI) Bus Master Cycles 19.7.2 Write Cycles On a write cycle, the EBI transfers data to an external memory or peripheral device. See Figure 19-2. MMC2107 EXTERNAL PERIPHERAL Freescale Semiconductor, Inc... ADDRESS DEVICE 1. DRIVE ADDRESS ON A[22:0]. 2. DRIVE TSIZ[1:0] PINS FOR OPERAND SIZE. 3. ASSERT CS IF USED. 4. CLEAR R/W TO WRITE. 5. ASSERT EB (ONE OR MORE DEPENDING ON DATA SIZE AND POSITION. 6. DRIVE DATA ON D[31:16] AND/OR D[15:0]. ACCEPT DATA 1. RECEIVE CS. 2. DECODE ADDRESS. 3. ASSERT TA IF NECESSARY FROM SLAVE DEVICE. 4. RECEIVE DATA FROM D[31:16] AND/OR D[15:0]. TERMINATE OUTPUT TRANSFER 1. NEGATE EB. TERMINATE CYCLE 1. NEGATE TA. START NEXT CYCLE 1. NEGATE CS IF USED. 2. REMOVE DATA FROM D[31:16] AND/OR D[15:0]. Figure 19-2. Write Cycle Flowchart MMC2107 - Rev. 2.0 MOTOROLA Technical Data External Bus Interface Module (EBI) For More Information On This Product, Go to: www.freescale.com 513 Freescale Semiconductor, Inc. External Bus Interface Module (EBI) 19.7.2.1 State 1 (X1) The EBI drives the address bus. The TSIZ[1:0] pins are driven to indicate the number of bytes in the transfer. TC[2:0] pins are driven to indicate the type of access. CS may be asserted to drive a device. OE is negated. Freescale Semiconductor, Inc... Later in state 1, R/W is driven low indicating a write cycle. One or more EB pins are asserted, depending on the size and position of the data to be transferred. If either the external TA pin or internal chip-select transfer acknowledge signal is asserted before the end of state 1, the EBI proceeds to state 2. 19.7.2.2 Optional Wait States (X2W) Wait states are inserted until the slave asserts the TA pin or the internal chip-select transfer acknowledge signal is asserted. The EBI drives its data onto data bus lines D[31:16] and/or D[15:0] on the first optional wait state. Wait states are counted in full clocks. 19.7.2.3 State 2 (X2) If the data was not already driven during optional wait states, the EBI drives its data onto D[31:16] and/or D[15:0] in state 2. EB is negated by the end of state 2. The address bus, data bus, R/W, CS, TC[2:0], and TSIZ[1:0] pins remain valid through state 2 to allow for static memory operation and signal skew. Figure 19-3 and Figure 19-4 illustrate external bus master cycles with and without wait states and show M*CORE bus activity. Technical Data 514 MMC2107 - Rev. 2.0 External Bus Interface Module (EBI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. External Bus Interface Module (EBI) Bus Master Cycles READ CLKOUT WRITE X1 X2 X1 X2 R/W A[22:0], TSIZ[1:0] A1 D[31:0] A2 D1 D2 CS Freescale Semiconductor, Inc... OE EB[3:0] EB[3:0] (EB SET AS WRITE ENABLE) TA, TEA Figure 19-3. Master Mode -- 1-Clock Read and Write Cycle READ CLKOUT X1 X2 WRITE X2W X2 X1 X2 X2W X2 R/W A[22:0], TSIZ[1:0] A1 D[31:0] A2 D1 D2 CS OE EB[3:0] EB[3:0] (EB SET AS WRITE ENABLE) TA, TEA Figure 19-4. Master Mode -- 2-Clock Read and Write Cycle MMC2107 - Rev. 2.0 MOTOROLA Technical Data External Bus Interface Module (EBI) For More Information On This Product, Go to: www.freescale.com 515 Freescale Semiconductor, Inc. External Bus Interface Module (EBI) 19.8 Bus Exception Operation Freescale Semiconductor, Inc... 19.8.1 Transfer Error Termination Normal bus cycle termination requires the assertion of the TA pin or the internal transfer acknowledge signal. Minimal bus exception support is provided by transfer error cycle termination. For transfer error cycle termination, the external TEA pin or the internal transfer error acknowledge signal is asserted. Transfer error cycle termination takes precedence over normal cycle termination, provided TEA assertion meets its timing constraints. The internal bus monitor will assert the internal transfer error acknowledge signal when TA response time is too long. 19.8.2 Transfer Abort Termination External bus cycles which are aborted by the M*CORE, still have the address, R/W, TC[2:0], TSIZ[1:0], CS (if used), OE (reads only), and SHS (if used) driven to the external pins. 19.9 Emulation Support 19.9.1 Emulation Chip-Selects (CSE[1:0]) While in emulation mode or master mode, special emulator chip-selects (CSE[1:0]) are driven externally to allow internal/external accesses to be tracked by external hardware See Table 19-4. In emulation mode, all port registers are mapped externally. CSE[1:0] = 10 whenever any emulated port registers are addressed. The lower bits of the address bus indicate the register accessed within the block. Accesses to the address space which contains the registers for the internal modules (except ports) are indicated by CSE[1:0] = 11. Internal accesses, other than to the specific module control registers, are indicated by CSE[1:0] = 01. To emulate internal FLASH, the external Technical Data 516 MMC2107 - Rev. 2.0 External Bus Interface Module (EBI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. External Bus Interface Module (EBI) Emulation Support D28 pin is driven low during reset configuration to disable the internal FLASH so that no conflict exists with the external memory device. It should be noted that at higher frequencies writes to external memories emulating the internal memories may require one clock for read accesses and two clocks for write accesses. Freescale Semiconductor, Inc... Table 19-4. Emulation Mode Chip-Select Summary(1) CSE1 CSE0 Indication in Emulation Mode 1 1 Internal access to any register space (excluding ports) Reset state (0x00c1_0000:0x00ff_ffff) 1 0 Internal access to ports register space (0x00c0_0000:0x00c0_ffff) 0 1 Internal access not covered by CSE encoding = 11, 10 (0x0000_0000:0x00bf_ffff; 0x0100_0000:0x07ff_ffff) 0 0 External access (0x8000_0000 to 0xffff_ffff) 1. CSE[1:0] is valid only for the duration of valid bus cycles or reset. Undefined otherwise. 19.9.2 Internal Data Transfer Display (Show Cycles) Internal data transfers normally occur without showing the internal data bus activity on the external data bus. For debugging purposes, however, it may be desirable to have internal cycle data appear on the external bus. These external bus cycles are referred to as show cycles and are distinguished from normal external cycles by the fact that OE and EB[3:0] remain negated. Regardless of whether show cycles are enabled, the EBI drives the address bus, TC[2:0], TSIZ[1:0] and R/W signals, indicating the internal cycle activity. When show cycles are disabled, D[31:0] remains in a high impedance state. When show cycles are enabled, OE and EB[3:0] remain negated while the internal data is presented on D[31:0] on the first clock tick after the termination of the internal cycle. Show cycles are always enabled in emulation mode. In master mode, show cycles are disabled coming out of reset and must be enabled by writing to the SHEN bit in the chip configuration register (CCR). MMC2107 - Rev. 2.0 MOTOROLA Technical Data External Bus Interface Module (EBI) For More Information On This Product, Go to: www.freescale.com 517 Freescale Semiconductor, Inc. External Bus Interface Module (EBI) NOTE: The PEPA and PCDPA bits in the ports must also be set to 1 to obtain full visibility. The waveforms shown in Figure 19-5 describe show cycles. 19.9.3 Show Strobe (SHS) Freescale Semiconductor, Inc... The show strobe (SHS) pin provides an indication to an external device (emulator or logic analyzer) when to latch address, TC[2:0], TSIZ[1:0], R/W, CSE, PSTAT, and data from the external pins. The SHS pin is enabled coming out of reset in emulation mode. In master mode, the SHS pin may be enabled by writing to the port E pin assignment register (PEPAR). For any external cycle or show cycle, the SHS pin is driven low to indicate valid address, TC, TSIZ, R/W, CSE, and PSTAT are present at the pins, and driven back high to indicate valid data. The SHS pin is driven low and back high only once per external bus cycle. See Figure 19-5 and Figure 19-6. INTERNAL CYCLE EXTERNAL READ X1 CLKOUT X2 R/W A{22:0], TSIZ[1:0] A1 A2 SHOW D[31:0] DATA D1 D2 SHS CSE[1:0] 00 CS OE EB[3:0] TA, TEA Figure 19-5. Internal (Show) Cycle Followed by External 1-Clock Read Technical Data 518 MMC2107 - Rev. 2.0 External Bus Interface Module (EBI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. External Bus Interface Module (EBI) Bus Monitor INTERNAL CYCLE EXTERNAL WRITE CLKOUT R/W A{22:0], TSIZ[1:0] A1 A2 SHOW D[31:0] DATA D1 D2 Freescale Semiconductor, Inc... SHS CSE[1:0] 00 CS OE EB[3:0] TA, TEA Figure 19-6. Internal (Show) Cycle Followed by External 1-Clock Write 19.10 Bus Monitor The bus monitor can be set detects excessively long bus access termination response times. Whenever an undecoded address is accessed or a peripheral is inoperative, the access is not terminated and the bus is potentially locked up while it waits for the required response. The bus monitor monitors the cycle termination response times during a bus cycle. If the cycle termination response time exceeds a programmed count, the bus monitor asserts an internal bus error. The bus monitor monitors the cycle termination response time (in system clock cycles) by using a programmable maximum allowable response period. There are four selectable response time periods for the bus monitor, selectable among 8, 16, 32, and 64 system clock cycles. The periods are selectable with the BMT[1:0] field in the chip configuration module CCR. The programmability of the timeout allows for varying external peripheral response times. The monitor is cleared and restarted MMC2107 - Rev. 2.0 MOTOROLA Technical Data External Bus Interface Module (EBI) For More Information On This Product, Go to: www.freescale.com 519 Freescale Semiconductor, Inc. External Bus Interface Module (EBI) on all bus accesses. If the cycle is not terminated within the selected response time, a timeout occurs and the bus monitor terminates the bus cycle. Freescale Semiconductor, Inc... The bus monitor can be configured with the BME bit in the chip configuration module CCR to monitor only internal bus accesses or both internal and external bus accesses. Also, the bus monitor can be disabled during debug mode for both internal and external accesses. Two external bus cycles are required for a single 32-bit access to a 16-bit port. If the bus monitor is enabled to monitor external accesses, then the bus monitor views the 32-bit access as two separate external bus cycles and not as one internal bus cycle. 19.11 Interrupts The EBI does not generate interrupt requests. Technical Data 520 MMC2107 - Rev. 2.0 External Bus Interface Module (EBI) For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 20. Chip Select Module Freescale Semiconductor, Inc... 20.1 Contents 20.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 521 20.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 522 20.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 523 20.5 Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 524 20.6 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 524 20.6.1 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 524 20.6.2 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 525 20.7 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530 20.8 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 531 20.2 Introduction The chip select module provides chip enable signals for external memory and peripheral devices. The chip selects can also be programmed to terminate bus cycles. Up to four asynchronous chip select signals are available. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Chip Select Module For More Information On This Product, Go to: www.freescale.com 521 Freescale Semiconductor, Inc. Chip Select Module 20.3 Features Freescale Semiconductor, Inc... Features of the chip select module include: * Reduced system complexity -- No external glue logic required for typical systems if chip selects are used. * Four programmable asynchronous active-low chip selects (CS[3:0]) -- Chip selects can be independently programmed with various features. * Control for external boot device -- CS0 can be enabled at reset to select an external boot device. * Fixed base addresses with 8-Mbyte block sizes * Support for emulating internal memory space -- When the EMINT bit is set in the chip configuration register (CCR), CS1 matches only addresses in the internal memory space. * Support for 16-bit and 32-bit external devices -- The external port size can be programmed to be 16 or 32 bits. * Programmable write protection -- Each chip select address range can be designated for read access only. * Programmable access protection -- Each chip select address range can be designated for supervisor access only. * Write-enable selection -- The enable byte pins (EB[3:0]) can be configured as byte enables (assert on both external read and write accesses) or write enables (only assert on external write accesses). * Bus cycle termination -- This option allows the chip select logic to terminate the bus cycle. * Programmable wait states -- To interface with various devices, up to seven wait states can be programmed before the access is terminated. * Programmable extra wait state for write accesses -- One wait state can be added to write accesses to allow writing to memories that require additional data setup time. Technical Data 522 MMC2107 - Rev. 2.0 Chip Select Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Chip Select Module Block Diagram 20.4 Block Diagram Figure 20-1 shows a programmable asynchronous chip select. All asynchronous chip selects have the same structure. All signals used to generate chip select signals are taken from the internal bus. Each chip select has a chip select control register to individually program the chip select characteristics. Freescale Semiconductor, Inc... All the chip selects share the same cycle termination generator. The active chip select for a particular bus cycle determines the number of wait states produced by the cycle termination generator before the cycle is terminated. ADDRESS M*CORE LOCAL BUS ADDRESS COMPARE MATCH DATA CHIP SELECT CONTROL REGISTERS PAD CONTROL ACCESS ATTRIBUTES CSx MATCH OPTION COMPARE TO CYCLE TERMINATION GENERATOR Figure 20-1. Chip Select Block Diagram MMC2107 - Rev. 2.0 MOTOROLA Technical Data Chip Select Module For More Information On This Product, Go to: www.freescale.com 523 Freescale Semiconductor, Inc. Chip Select Module 20.5 Signals Table 20-1 provides an overview of the signals described here. Freescale Semiconductor, Inc... Table 20-1. Signal Properties Name Function Reset State Pullup CS0 Chip select 0 pin 1 Active CS1 Chip select 1 pin 1 Active CS2 Chip select 2 pin 1 Active CS3 Chip select 3 pin 1 Active CS[3:0] are chip-select outputs. CS[3:0] are available for general-purpose input/output (I/O) when not configured for chip select operation. 20.6 Memory Map and Registers Table 20-2 shows the chip select memory map. The registers are described in 20.6.2 Registers. 20.6.1 Memory Map Table 20-2. Chip Select Memory Map Address Bits 31-16 Access(1), (2) Bits 15-0 0x00c2_0000 CSCR0 -- chip select control register 0 CSCR1 -- chip select control register 1 S 0x00c2_0004 CSCR2 -- chip select control register 2 CSCR3 -- chip select control register 3 S 1. User mode accesses to supervisor-only address locations have no effect and result in a cycle termination transfer error. 2. S = CPU supervisor mode access only. Technical Data 524 MMC2107 - Rev. 2.0 Chip Select Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Chip Select Module Memory Map and Registers 20.6.2 Registers The chip programming model consists of four chip select control registers (CSCR0-CSCR3), one for each chip select (CS[3:0]). CSCR0-CSCR3 are read/write always and define the conditions for asserting the chip select signals. Freescale Semiconductor, Inc... All the chip select control registers are the same except for the reset states of the CSEN and PS bits in CSCR0 and the CSEN bit in CSCR1. This allows CS0 to be enabled at reset with either a 16-bit or 32-bit port size for selecting an external boot device and allows CS1 to be used to emulate internal memory. Address: 0x00c2_0000 and 0x00c2_0001 Bit 15 14 13 12 11 10 9 Bit 8 SO RO PS WWS WE WS2 WS1 WS0 0 0 See note 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 TAEN CSEN 1 See note Read: Write: Reset: Read: Write: Reset: 0 0 0 0 0 0 = Writes have no effect and the access terminates without a transfer error exception. Note: Reset state determined during reset configuration. Figure 20-2. Chip Select Control Register 0 (CSCR0) MMC2107 - Rev. 2.0 MOTOROLA Technical Data Chip Select Module For More Information On This Product, Go to: www.freescale.com 525 Freescale Semiconductor, Inc. Chip Select Module Address: 0x00c2_0002 and 0x00c2_0003 Read: Bit 15 14 13 12 11 10 9 Bit 8 SO RO PS WWS WE WS2 WS1 WS0 0 0 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 TAEN CSEN 0 0 0 0 0 0 1 See note Write: Reset: Read: Write: Freescale Semiconductor, Inc... Reset: = Writes have no effect and the access terminates without a transfer error exception. Note: Reset state determined during reset configuration. Figure 20-3. Chip Select Control Register 1 (CSCR1) Address: 0x00c2_0004 and 0x00c2_0005 Bit 15 14 13 12 11 10 9 Bit 8 SO RO PS WWS WE WS2 WS1 WS0 0 0 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 TAEN CSEN 1 0 Read: Write: Reset: Read: Write: Reset: 0 0 0 0 0 0 = Writes have no effect and the access terminates without a transfer error exception. Figure 20-4. Chip Select Control Register 2 (CSCR2) Technical Data 526 MMC2107 - Rev. 2.0 Chip Select Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Chip Select Module Memory Map and Registers Address: 0x00c2_00006 and 0x00c2_0007 Read: Bit 15 14 13 12 11 10 9 Bit 8 SO RO PS WWS WE WS2 WS1 WS0 0 0 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 TAEN CSEN 0 0 0 0 0 0 1 0 Write: Reset: Read: Write: Freescale Semiconductor, Inc... Reset: = Writes have no effect and the access terminates without a transfer error exception. Figure 20-5. Chip Select Control Register 3 (CSCR3) SO -- Supervisor-Only Bit The SO bit restricts user mode access to the address range defined by the corresponding chip select. If the SO bit is 1, only supervisor mode access is permitted. If the SO bit is 0, both supervisor and user level accesses are permitted. When an access is made to a memory space assigned to the chip select, the chip select logic compares the SO bit with bit 2 of the internal transfer code, which indicates whether the access is at the supervisor or user level. If the chip select logic detects a protection violation, the access is ignored. 1 = Only supervisor mode accesses allowed; user mode accesses ignored by chip select logic 0 = Supervisor and user mode accesses allowed RO -- Read-Only Bit The RO bit restricts write accesses to the address range defined by the corresponding chip select. If the RO bit is 1, only read access is permitted. If the RO bit is 0, both read and write accesses are permitted. When an access is made to a memory space assigned to the chip select, the chip select logic compares the RO bit with the internal MMC2107 - Rev. 2.0 MOTOROLA Technical Data Chip Select Module For More Information On This Product, Go to: www.freescale.com 527 Freescale Semiconductor, Inc. Chip Select Module read/write signal, which indicates whether the access is a read (read/write = 1) or a write (read/write = 0). If the chip select logic detects a violation (RO = 1 with read/write = 0), the access is ignored. 1 = Only read accesses allowed; write accesses ignored by the chip select logic 0 = Read and write accesses allowed PS -- Port Size Bit Freescale Semiconductor, Inc... The PS bit defines the width of the external data port supported by the chip select as either 16-bit or 32-bit. When a chip select is programmed as a 16-bit port, the external device must be connected to D[31:16]. For 32-bit accesses to 16-bit ports, the external memory interface initiates two bus cycles and multiplexes data as needed to complete the data transfer. 1 = 32 bit port 0 = 16 bit port WWS -- Write Wait State Bit The WWS bit determines if an additional wait state is required for write cycles. WWS does not affect read cycles. 1 = One additional wait state added for write cycles 0 = No additional wait state added for write cycles WE -- Write Enable Bit The WE bit defines when the enable byte output pins (EB[3:0]) are asserted. When WE is 0, EB[3:0] are configured as byte enables and assert for both external read and external write accesses. When WE is 1, EB[3:0] are configured as write enables and assert only for external write accesses. 1 = EB[3:0] configured as write enables 0 = EB[3:0] configured as byte enables NOTE: The WE bit has no effect on the EB[3:0] pin function if the chip select is not active. If the chip select is not active, the EB[3:0] pin function is byte enable by default. WS[2:0] -- Wait States Field The WS field determines the number of wait states for the chip select logic to insert before asserting the internal cycle termination signal. One wait state is equal to one system clock cycle. If WS is configured for zero wait states, then the internal cycle termination signal is Technical Data 528 MMC2107 - Rev. 2.0 Chip Select Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Chip Select Module Memory Map and Registers asserted in the clock cycle following the start of the cycle access, resulting in one-clock transfers. A WS configured for one wait state means that the internal cycle termination signal is asserted two clock cycles after the start of the cycle access. Since the internal cycle termination signal is asserted internally after the programmed number of wait states, software can adjust the bus timing to accommodate the access speed of the external device. With up to seven possible wait states, even slow devices can be interfaced with the MCU. Freescale Semiconductor, Inc... Table 20-3. Chip Select Wait States Encoding Number of Wait States WS[2:0] WWS = 0 WWS = 1 Read Access Write Access Read Access Write Access 000 0 0 0 1 001 1 1 1 2 010 2 2 2 3 011 3 3 3 4 100 4 4 4 5 101 5 5 5 6 110 6 6 6 7 111 7 7 7 8 TAEN -- Transfer Acknowledge Enable Bit The TAEN bit determines whether the internal cycle termination signal is asserted by the chip select logic when accesses occur to the address range defined by the corresponding chip select. When TAEN is 0, an external device is responsible for asserting the external TA pin to terminate the bus access. When TAEN is 1, the chip select logic asserts the internal cycle termination signal after a time determined by the programmed number of wait states. When TAEN is 1, external logic can still terminate the access before the internal cycle termination signal is asserted by asserting the external TA pin. 1 = Internal cycle termination signal asserted by chip select logic 0 = Internal cycle termination signal asserted by external logic MMC2107 - Rev. 2.0 MOTOROLA Technical Data Chip Select Module For More Information On This Product, Go to: www.freescale.com 529 Freescale Semiconductor, Inc. Chip Select Module CSEN -- Chip Select Enable Bit The CSEN bit enables the chip select logic. When the chip select function is disabled, the CSx signal is negated high. 1 = Chip select function enabled 0 = Chip select function disabled 20.7 Functional Description Freescale Semiconductor, Inc... Each chip select can provide a chip enable signal for an external device and assert the internal bus cycle termination signal. Setting the CSEN bit in CSCR enables the chip select to provide an external chip enable. Setting both the CSEN and TAEN bits in CSCR enables the chip select to generate the internal bus cycle termination signal. Both the chip select pin assertion and the bus cycle termination function depend on an initial address/option match for activation. During the matching process, the fixed base address of each chip select is compared to the corresponding address for the bus cycle to determine whether an address match has occurred. This match is further qualified by comparing the internal read/write indication and access type with the programmed values in CSCR of each chip select. When the address and option information match the current cycle, the chip select is activated. If no chip select matches the bus cycle information for the current access, the chip select logic does not respond in any way. Only one chip select can be active for a given bus cycle. The configuration of the active chip select, determined by the wait state (WS/WWS) field, the port size (PS) field, and the write enable (WE) field, is used for the access. NOTE: WWS and WS are valid only if the TAEN bit is 1 for the active chip select. When no chip select pin is available, the active chip select can still terminate the bus cycle. If both the CSEN and TAEN bits are 1 and the address/options match the chip select configuration, then the chip select logic asserts the internal termination signal; the bus cycle terminates after the programmed number of wait states. If the external TA or TEA Technical Data 530 MMC2107 - Rev. 2.0 Chip Select Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Chip Select Module Interrupts pin is asserted before the chip select logic asserts the internal cycle termination signal, then the bus cycle is terminated early. If internal address bit 31 is 0, then the access is internal. If internal address bit 31 is 1, then the access is external. NOTE: Chip select logic does not decode internal address bits A[30:25]. Freescale Semiconductor, Inc... Table 20-4. Chip Select Address Range Encoding Chip Select Block Size Address Bits Compared (A[31:23])(1) CS0 8 MB 1XXX_XXX0_0 CS1 8 MB 1XXX_XXX0_1(2) CS2 8 MB 1XXX_XXX1_0 CS3 8 MB 1XXX_XXX1_1 1. The chip selects do not decode A[30:25]. Thus, the total 32-Mbyte block size is repeated/mirrored in external memory space. 2. If the EMINT bit in the chip configuration module CCR is set, then CS1 matches only internal accesses to the 8-MB block starting at address 0 to support emulation of internal memory. Thus, A[31:23] match 0xxx_xxx0_0. 20.8 Interrupts The chip select module does not generate interrupt requests. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Chip Select Module For More Information On This Product, Go to: www.freescale.com 531 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Chip Select Module Technical Data 532 MMC2107 - Rev. 2.0 Chip Select Module For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 21. JTAG Test Access Port and OnCE 21.1 Contents Freescale Semiconductor, Inc... 21.2 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 535 21.3 Top-Level Test Access Port (TAP) . . . . . . . . . . . . . . . . . . . . 537 21.3.1 Test Clock (TCLK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 538 21.3.2 Test Mode Select (TMS) . . . . . . . . . . . . . . . . . . . . . . . . . 538 21.3.3 Test Data Input (TDI) . . . . . . . . . . . . . . . . . . . . . . . . . . . .538 21.3.4 Test Data Output (TDO) . . . . . . . . . . . . . . . . . . . . . . . . . . 538 21.3.5 Test Reset (TRST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 538 21.3.6 Debug Event (DE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 538 21.4 Top-Level TAP Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . 540 21.5 Instruction Shift Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 541 21.5.1 EXTEST Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 541 21.5.2 IDCODE Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 542 21.5.3 SAMPLE/PRELOAD Instruction . . . . . . . . . . . . . . . . . . . . 543 21.5.4 ENABLE_MCU_ONCE Instruction . . . . . . . . . . . . . . . . . . 543 21.5.5 HIGHZ Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 544 21.5.6 CLAMP Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 544 21.5.7 BYPASS Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 544 21.6 IDCODE Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .545 21.7 Bypass Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 546 21.8 Boundary SCAN Register. . . . . . . . . . . . . . . . . . . . . . . . . . . 546 21.9 Restrictions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 546 21.10 Non-Scan Chain Operation . . . . . . . . . . . . . . . . . . . . . . . . . 547 21.11 Boundary Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 547 21.12 Low-Level TAP (OnCE) Module . . . . . . . . . . . . . . . . . . . . . . 553 21.13 Signal Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 555 21.13.1 Debug Serial Input (TDI) . . . . . . . . . . . . . . . . . . . . . . . . . 555 21.13.2 Debug Serial Clock (TCLK) . . . . . . . . . . . . . . . . . . . . . . .555 21.13.3 Debug Serial Output (TDO) . . . . . . . . . . . . . . . . . . . . . . .555 MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 533 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Freescale Semiconductor, Inc... 21.13.4 Debug Mode Select (TMS). . . . . . . . . . . . . . . . . . . . . . . . 556 21.13.5 Test Reset (TRST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 556 21.13.6 Debug Event (DE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 556 21.14 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 556 21.14.1 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .557 21.14.2 OnCE Controller and Serial Interface. . . . . . . . . . . . . . . . 558 21.14.3 OnCE Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . 559 21.14.3.1 Internal Debug Request Input (IDR) . . . . . . . . . . . . . . 559 21.14.3.2 CPU Debug Request (DBGRQ). . . . . . . . . . . . . . . . . . 560 21.14.3.3 CPU Debug Acknowledge (DBGACK). . . . . . . . . . . . . 560 21.14.3.4 CPU Breakpoint Request (BRKRQ). . . . . . . . . . . . . . . 560 21.14.3.5 CPU Address, Attributes (ADDR, ATTR) . . . . . . . . . . . 560 21.14.3.6 CPU Status (PSTAT) . . . . . . . . . . . . . . . . . . . . . . . . . . 560 21.14.3.7 OnCE Debug Output (DEBUG) . . . . . . . . . . . . . . . . . .560 21.14.4 OnCE Controller Registers. . . . . . . . . . . . . . . . . . . . . . . . 561 21.14.4.1 OnCE Command Register . . . . . . . . . . . . . . . . . . . . . . 561 21.14.4.2 OnCE Control Register . . . . . . . . . . . . . . . . . . . . . . . . 564 21.14.4.3 OnCE Status Register . . . . . . . . . . . . . . . . . . . . . . . . . 568 21.14.5 OnCE Decoder (ODEC) . . . . . . . . . . . . . . . . . . . . . . . . . . 570 21.14.6 Memory Breakpoint Logic . . . . . . . . . . . . . . . . . . . . . . . . 570 21.14.6.1 Memory Address Latch (MAL) . . . . . . . . . . . . . . . . . . .571 21.14.6.2 Breakpoint Address Base Registers . . . . . . . . . . . . . . 571 21.14.7 Breakpoint Address Mask Registers . . . . . . . . . . . . . . . . 571 21.14.7.1 Breakpoint Address Comparators . . . . . . . . . . . . . . . . 572 21.14.7.2 Memory Breakpoint Counters . . . . . . . . . . . . . . . . . . . 572 21.14.8 OnCE Trace Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 572 21.14.8.1 OnCE Trace Counter . . . . . . . . . . . . . . . . . . . . . . . . . . 573 21.14.8.2 Trace Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 574 21.14.9 Methods of Entering Debug Mode . . . . . . . . . . . . . . . . . . 574 21.14.9.1 Debug Request During RESET . . . . . . . . . . . . . . . . . . 574 21.14.9.2 Debug Request During Normal Activity . . . . . . . . . . . . 575 21.14.9.3 Debug Request During Stop, Doze, or Wait Mode . . . 575 21.14.9.4 Software Request During Normal Activity . . . . . . . . . . 575 21.14.10 Enabling OnCE Trace Mode . . . . . . . . . . . . . . . . . . . . . . 575 21.14.11 Enabling OnCE Memory Breakpoints . . . . . . . . . . . . . . . 576 21.14.12 Pipeline Information and Write-Back Bus Register . . . . . 576 21.14.12.1 Program Counter Register . . . . . . . . . . . . . . . . . . . . . . 577 21.14.12.2 Instruction Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 577 Technical Data 534 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Introduction Freescale Semiconductor, Inc... 21.14.12.3 Control State Register . . . . . . . . . . . . . . . . . . . . . . . . . 577 21.14.12.4 Writeback Bus Register . . . . . . . . . . . . . . . . . . . . . . . . 579 21.14.12.5 Processor Status Register . . . . . . . . . . . . . . . . . . . . . . 579 21.14.13 Instruction Address FIFO Buffer (PC FIFO) . . . . . . . . . . . 580 21.14.14 Reserved Test Control Registers . . . . . . . . . . . . . . . . . . .581 21.14.15 Serial Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 581 21.14.16 OnCE Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 582 21.14.17 Target Site Debug System Requirements . . . . . . . . . . . . 582 21.14.18 Interface Connector for JTAG/OnCE Serial Port . . . . . . . 582 21.2 Introduction The MMC2107 has two JTAG (Joint Test Action Group) TAP (test access port) controllers: 1. A top-level controller that allows access to the MMC2107's boundary scan (external pins) register, IDCODE register, and bypass register 2. A low-level OnCE (on-chip emulation) controller that allows access to MMC2107's central processor unit (CPU) and debugger-related registers At power-up, only the top-level TAP controller will be visible. If desired, a user can then enable the low-level OnCE controller which will in turn disable the top-level TAP controller. The top-level TAP controller will remain disabled until either power is removed and reapplied to the MMC2107 or until the test reset signal, TRST, is asserted (logic 0). The OnCE TAP controller can be enabled in either of two ways: 1. With the top-level TAP controller in its test-logic-reset state: a. Deassert TRST, test reset (logic1) b. Assert DE, the debug event (logic 0) for two TCLK, test clock, cycles 2. Shift the ENABLE_MCU_ONCE instruction, 0x3, into the top-level TAP controller's instruction register (IR) and pass through the TAP controller state update-IR. Refer to Figure 21-1. MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 535 536 TDI 0 LSB MSB 3 Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com B TDO TDO MUX A SELECT 0 LSB BYPASS 0 LSB MSB 31 LOW-LEVEL TDO MUX MSB 199 IDCODE (SHIFT) REGISTER 1 BIT MUX OnCE CMD INSTRUCTION REGISTER SELECT OnCE TAP CONTROLLER LOW-LEVEL TAP (OnCE) MODULE Figure 21-1. Top-Level Tap Module and Low-Level (OnCE) TAP Module SELECT TOP-LEVEL TDO MUX BOUNDARY SCAN (SHIFT) REGISTER IF YES, THEN B, SELECT LOW-LEVEL (OnCE) TDO; IF NO, THAN A, SELECT TOP-LEVEL TDO TAP INSTRUCTION REGISTER IR[3:0] = 0 x 3? ENABLE_MCU_ONCE CMD TAP CONTROLLER TOP-LEVEL TAP MODULE DE TCLK TMS TRST Freescale Semiconductor, Inc... OnCE DATA REGISTERS Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE MMC2107 - Rev. 2.0 MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Top-Level Test Access Port (TAP) 21.3 Top-Level Test Access Port (TAP) Freescale Semiconductor, Inc... The MMC2107 provides a dedicated user-accessible test access port (TAP) that is fully compatible with the IEEE 1149.1 Standard Test Access Port and Boundary-Scan Architecture. Problems associated with testing high-density circuit boards have led to development of this proposed standard under the sponsorship of the Test Technology Committee of IEEE and the Joint Test Action Group (JTAG). The MMC2107 implementation supports circuit-board test strategies based on this standard. The top-level TAP consists of five dedicated signal pins, a 16-state TAP controller, an instruction register, and three data registers, a boundary scan register for monitoring and controlling the device's external pins, a device identification register, and a 1-bit bypass (do nothing) register. The top-level TAP provides the ability to: 1. Perform boundary scan (external pin) drive and monitor operations to test circuitry external to the MMC2107 2. Disable the MMC2107's output pins 3. Read the MMC2107's IDCODE device identification register CAUTION: Certain precautions must be observed to ensure that the top-level TAP module does not interfere with non-test operation. See 21.10 Non-Scan Chain Operation for details. The MMC2107's top-level TAP module includes a TAP controller, a 4-bit instruction register, and three test data registers (a 1-bit bypass register, a 200-bit boundary scan register, and a 32-bit IDCODE register). The top-level tap controller and the low-level (OnCE) TAP controller share the external signals described here. MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 537 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE 21.3.1 Test Clock (TCLK) TCLK is a test clock input to synchronize the test logic. TCLK is independent of the MMC2107 processor clock. It includes an internal pullup resistor. Freescale Semiconductor, Inc... 21.3.2 Test Mode Select (TMS) TMS is a test mode select input (with an internal pullup resistor) that is sampled on the rising edge of TCLK to sequence the TAP controller's state machine. 21.3.3 Test Data Input (TDI) TDI is a serial test data input (with an internal pullup resistor) that is sampled on the rising edge of TCLK. 21.3.4 Test Data Output (TDO) TDO is a three-state test data output that is actively driven in the shift-IR and shift-DR controller states. TDO changes on the falling edge of TCLK. 21.3.5 Test Reset (TRST) TRST is an active low asynchronous reset with an internal pullup resistor that forces the TAP controller into the test-logic-reset state. 21.3.6 Debug Event (DE) This is a bidirectional, active-low signal. As an output, this signal will be asserted for three system clocks, synchronous to the rising CLKOUT edge, to acknowledge that the CPU has entered debug mode as a result of a debug request or a breakpoint condition. Technical Data 538 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Top-Level Test Access Port (TAP) Freescale Semiconductor, Inc... As an input, this signal provides multiple functions such as: NOTE: * The main function is a means of entering debug mode from an external command controller. This signal, when asserted, causes the CPU to finish the current instruction being executed, save the instruction pipeline information, enter debug mode, and wait for commands to be entered from the serial debug input line. This input must be asserted for at least three system clocks, sampled with the rising CLKOUT edge. This function is ignored during reset. While the processor is in debug mode, this signal is still sampled but has no effect until debug mode is exited. * Another input function is to enable OnCE. This is an alternate method to the ENABLE_MCU_ONCE JTAG command to enable the OnCE logic to be accessible via the JTAG interface. This input signal must be asserted low (while in the test-logic-reset state with POR/TRST not asserted) for at least two TCLK rising edges. Once enabled, the OnCE will remain enabled until the next POR or TRST resets. * Another input function is as a wake-up event from a low-power mode of operation. Asynchronously asserting this signal will cause the clock controller to restart. This signal must be held asserted until the M*CORE receives three valid rising edges on the system clock. Then the processor will exit the low-power mode and go into debug mode. If used to enter debug mode, DE must be pulled negated before the processor exits debug mode to prevent a still low signal from being unintentionally recognized as another debug request. Also, asserting this signal to enter debug mode may prevent external logic from seeing the processor output acknowledgment since the external pullup may not be able to pull the signal negated before the handshake is asserted. Finally, if using this signal to enable OnCE outside of reset it may be seen as a request to enter debug mode. MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 539 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE 21.4 Top-Level TAP Controller The top-level TAP controller is responsible for interpreting the sequence of logical values on the TMS signal. It is a synchronous state machine that controls the operation of the JTAG logic. The machine's states are shown in Figure 21-2. The value shown adjacent to each arc represents the value of the TMS signal sampled on the rising edge of the TCLK signal. Freescale Semiconductor, Inc... The top-level TAP controller can be asynchronously reset to the testlogic-reset state by asserting TRST, test reset. As Figure 21-2 shows, holding TMS high (to logic 1) while clocking TCLK through at least five rising edges will also cause the state machine to enter its test-logic-reset state. TEST-LOGICRESET 1 0 RUN-TEST/IDLE 1 SELECT-DR_SCAN 0 1 SELECT-IR_SCAN 0 0 1 1 CAPTURE-DR CAPTURE-IR 0 0 SHIFT-DR 1 SHIFT-IR 0 1 1 EXIT1-DR PAUSE-IR 0 EXIT2-DR 1 0 UPDATE-DR 0 0 EXIT2-IR 1 1 1 1 0 PAUSE-DR 1 0 EXIT1-IR 0 0 1 UPDATE-IR 1 0 Figure 21-2. Top-Level TAP Controller State Machine Technical Data 540 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Instruction Shift Register 21.5 Instruction Shift Register Freescale Semiconductor, Inc... The MMC2107 top-level TAP module uses a 4-bit instruction shift register with no parity. This register transfers its value to a parallel hold register and applies an instruction on the falling edge of TCLK when the TAP state machine is in the update-IR state. To load the instructions into the shift portion of the register, place the serial data on the TDI pin prior to each rising edge of TCLK. The MSB of the instruction shift register is the bit closest to the TDI pin and the LSB is the bit closest to the TDO pin. Table 21-1 lists the instructions supported along with their opcodes, IR3-IR0. The last three instructions in the table are reserved for manufacturing purposes only. Unused opcodes are currently decoded to perform the BYPASS operation, but Motorola reserves the right to change their decodings in the future. 21.5.1 EXTEST Instruction The external test instruction (EXTEST) selects the boundary-scan register. The EXTEST instruction forces all output pins and bidirectional pins configured as outputs to the preloaded fixed values (with the SAMPLE/PRELOAD instruction) and held in the boundary-scan update registers. The EXTEST instruction can also configure the direction of bidirectional pins and establish high-impedance states on some pins. EXTEST also asserts internal reset for the MMC2107 system logic to force a predictable internal state while performing external boundary scan operations. MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 541 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Table 21-1. JTAG Instructions Freescale Semiconductor, Inc... Instruction IR3-IR0 Instruction Summary EXTEST 0000 Selects the boundary scan register while applying fixed values to output pins and asserting functional reset IDCODE 0001 Selects IDCODE register for shift SAMPLE/PRELOAD 0010 Selects the boundary scan register for shifting, sampling, and preloading without disturbing functional operation ENABLE_MCU_ONCE 0011 Instruction to enable the M*CORE TAP controller HIGHZ 1001 Selects the bypass register while three-stating all output pins and asserting functional reset CLAMP 1100 Selects bypass while applying fixed values to output pins and asserting functional reset BYPASS 1111 Selects the bypass register for data operations Reserved 0100 0110 Instruction for chip manufacturing purposes only Reserved 0101 Instruction for chip manufacturing purposes only(1) Reserved 0111-1000 1101-1110 Decoded to select bypass register(2) 1010-1011 1. To exit this instruction, the TRST pin must be asserted or power-on reset. 2. Motorola reserves the right to change the decoding of the unused opcodes in the future. 21.5.2 IDCODE Instruction The IDCODE instruction selects the 32-bit IDCODE register for connection as a shift path between the TDI pin and the TDO pin. This instruction allows interrogation of the MMC2107 to determine its version number and other part identification data. The IDCODE register has been implemented in accordance with the IEEE 1149.1 standard so that the least significant bit of the shift register stage is set to logic 1 on the rising edge of TCLK following entry into the capture-DR state. Therefore, the first bit to be shifted out after selecting the IDCODE register is always Technical Data 542 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Instruction Shift Register a logic 1. The remaining 31 bits are also set to fixed values on the rising edge of TCLK following entry into the capture-DR state. IDCODE is the default instruction placed into the instruction register when the top-level TAP resets. Thus, after a TAP reset, the IDCODE (data) register will be selected automatically. 21.5.3 SAMPLE/PRELOAD Instruction Freescale Semiconductor, Inc... The SAMPLE/PRELOAD instruction provides two separate functions. First, it obtains a sample of the system data and control signals present at the MMC2107 input pins and just prior to the boundary scan cell at the output pins. This sampling occurs on the rising edge of TCLK in the capture-DR state when an instruction encoding of hex 2 is resident in the instruction register. The user can observe this sampled data by shifting it through the boundary scan register to the output TDO by using the shift-DR state. Both the data capture and the shift operation are transparent to system operation. NOTE: The user is responsible for providing some form of external synchronization to achieve meaningful results because there is no internal synchronization between TCLK and the system clock. The second function of the SAMPLE/PRELOAD instruction is to initialize the boundary scan register update cells before selecting EXTEST or CLAMP. This is achieved by ignoring the data being shifted out of the TDO pin while shifting in initialization data. The update-DR state in conjunction with the falling edge of TCLK can then transfer this data to the update cells. This data will be applied to the external output pins when EXTEST or CLAMP instruction is applied. 21.5.4 ENABLE_MCU_ONCE Instruction The ENABLE_MCU_ONCE is a public instruction to enable the M*CORE OnCE TAP controller. When the OnCE TAP controller is enabled, the top-level TAP controller connects the internal OnCE TDO to the pin TDO and remains in the run-test/idle state. It will remain in this state until TRST is asserted. While the OnCE TAP controller is enabled, the top-level JTAG remains transparent. MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 543 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE 21.5.5 HIGHZ Instruction Freescale Semiconductor, Inc... The HIGHZ instruction is provided as a manufacturer's optional public instruction to prevent having to backdrive the output pins during circuit-board testing. When HIGHZ is invoked, all output drivers, including the 2-state drivers, are turned off (for example, high impedance). The instruction selects the bypass register. HIGHZ also asserts internal reset for the MMC2107 system logic to force a predictable internal state. 21.5.6 CLAMP Instruction The CLAMP instruction selects the bypass register and asserts internal reset while simultaneously forcing all output pins and bidirectional pins configured as outputs to the fixed values that are preloaded and held in the boundary scan update register. This instruction enhances test efficiency by reducing the overall shift path to a single bit (the bypass register) while conducting an EXTEST type of instruction through the boundary scan register. 21.5.7 BYPASS Instruction The BYPASS instruction selects the single-bit bypass register, creating a single-bit shift register path from the TDI pin to the bypass register to the TDO pin. This instruction enhances test efficiency by reducing the overall shift path when a device other than the MMC2107 processor becomes the device under test on a board design with multiple chips on the overall IEEE 1149.1 standard defined boundary scan chain. The bypass register has been implemented in accordance with IEEE 1149.1 standard so that the shift register state is set to logic 0 on the rising edge of TCLK following entry into the capture-DR state. Therefore, the first bit to be shifted out after selecting the bypass register is always a logic 0 (to differentiate a part that supports an IDCODE register from a part that supports only the bypass register). Technical Data 544 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE IDCODE Register 21.6 IDCODE Register Freescale Semiconductor, Inc... An IEEE 1149.1 standard compliant JTAG identification register (IDCODE) has been included on the MMC2107. Bit 31 30 29 28 27 26 25 Bit 24 0 0 0 0 0 1 0 1 Bit 23 22 21 20 19 18 17 Bit 16 1 1 0 0 0 0 0 1 Bit 15 14 13 12 11 10 9 Bit 8 0 1 1 1 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 1 1 1 0 1 Figure 21-3. IDCODE Register Bit Specification Bits 31-28 -- Version Number (Part Revision Number) This is equivalent to the lower four bits of the PRN of the chip identification register located in the chip configuration module. Bits 27-22 -- Design Center Indicates the Motorola Microcontroller Division Bits 21-12 -- Device Number (Part Identification Number) Bits 19-12 are equivalent to the PIN of the chip identification register located in the chip configuration module. Bits 11-1 -- JEDEC ID Indicates the reduced JEDEC ID for Motorola. JEDEC refers to the Joint Electron Device Engineering Council. Refer to JEDEC publication 106-A and chapter 11 of the IEEE 1149.1 standard for further information on this field. Bit 0 Differentiates this register as the JTAG IDCODE register (as opposed to the bypass register), according to the IEEE 1149.1 standard MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 545 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE 21.7 Bypass Register The MMC2107 includes an IEEE 1149.1 standard-compliant bypass register, which creates a single bit shift register path from TDI to the bypass register to TDO when the BYPASS instruction is selected. Freescale Semiconductor, Inc... 21.8 Boundary SCAN Register MMC2107 includes an IEEE 1149.1 standard-compliant boundary-scan register. The boundary-scan register is connected between TDI and TDO when the EXTEST or SAMPLE/PRELOAD instructions are selected. This register captures signal pin data on the input pins, forces fixed values on the output signal pins, and selects the direction and drive characteristics (a logic value or high impedance) of the bidirectional and three-state signal pins. 21.9 Restrictions The test logic is implemented using static logic design, and TCLK can be stopped in either a high or low state without loss of data. The system logic, however, operates on a different system clock which is not synchronized to TCLK internally. Any mixed operation requiring the use of the IEEE 1149.1 standard test logic, in conjunction with system functional logic that uses both clocks, must have coordination and synchronization of these clocks done externally. The control afforded by the output enable signals using the boundary scan register and the EXTEST instruction requires a compatible circuit-board test environment to avoid device-destructive configurations. The user must avoid situations in which MMC2107 output drivers are enabled into actively driven networks. Technical Data 546 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Non-Scan Chain Operation MMC2107 features a low-power stop mode. The interaction of the scan chain interface with low-power stop mode is: 1. The TAP controller must be in the test-logic-reset state to either enter or remain in the low-power stop mode. Leaving the test-logic-reset state negates the ability to achieve low-power, but does not otherwise affect device functionality. Freescale Semiconductor, Inc... 2. The TCLK input is not blocked in low-power stop mode. To consume minimal power, the TCLK input should be externally connected to VDD. 3. The TMS, TDI, TRST pins include on-chip pullup resistors. In low-power stop mode, these three pins should remain either unconnected or connected to VDD to achieve minimal power consumption. 21.10 Non-Scan Chain Operation Keeping the TAP controller in the test-logic-reset state will ensure that the scan chain test logic is kept transparent to the system logic. It is recommended that TMS, TDI, TCLK, and TRST be pulled up. TRST could be connected to ground. However, since there is a pullup on TRST, some amount of current will result. JTAG will be initialized to the test-logic-reset state on power-up without TRST asserted low due to the JTAG power-on-reset internal input. The low-level TAP module in the M*CORE also has the power-on-reset input. 21.11 Boundary Scan The MMC2107 boundary-scan register contains 200 bits. This register can be connected between TDI and TDO when EXTEST or SAMPLE/PRELOAD instructions are selected. This register is used for capturing signal pin data on the input pins, forcing fixed values on the output signal pins, and selecting the direction and drive characteristics (a logic value or high impedance) of the bidirectional and three-state signal pins. This IEEE 1149.1 standard-compliant boundary-scan register contains bits for bonded-out and non-bonded signals excluding JTAG signals, analog signals, power supplies, compliance enable pins, and clock MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 547 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE signals.To maintain JTAG compliance, TEST should be held to logic 0 and DE should be held to logic 1. These non-scanned pins are shown in Table 21-2. Freescale Semiconductor, Inc... Table 21-2. List of Pins Not Scanned in JTAG Mode Pin Name Pin Type EXTAL Clock/analog XTAL Clock/analog VDDSYN Supply VSSSYN Supply PQA4-PQA3 and PQA1-PQA0 Analog PQB3-PQB0 Analog VRH Supply VRL Supply VDDA Supply VSSA Supply VDDH Supply TRST JTAG TCLK JTAG TMS JTAG TDI JTAG TDO JTAG DE JTAG compliance enable TEST JTAG compliance enable Vpp Supply VDDF Supply VSSF Supply VSTBY Supply VDD Supply VSS Supply Technical Data 548 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Boundary Scan Freescale Semiconductor, Inc... Table 21-3 defines the boundary-scan register. * The first column shows bit numbers assigned to each of the register's cells. The bit nearest to TDO (the first to be shifted in) is defined as bit 0. * The second column lists the logical state bit for each MMC2107 pin alternately with the read/write direction control bit for that pin. The logic state bits are non-inverting with respect to their associated pins, so that a 1 logical state bit equates to a logical high voltage on its corresponding pin. A direction control bit value of 1 causes a pin's logical state to be expressed by its logic state bit, a read of a pin. A direction control bit value of 0 causes a pin's logical voltage to follow the state of its logical state bit, a write to a pin. Table 21-3. Boundary-Scan Register Definition (Sheet 1 of 4) (Note: Shaded regions indicate optional pins) Bit Logical State and Direction Control Bits for Each Pin Logical State and Direction Control Bits for Each Pin Bit 0 D31 logical state 17 A18 direction control 1 D31 direction control 18 A19 logical state 2 A12 logical state 19 A19 direction control 3 A12 direction control 20 RSTOUT logical state 4 A13 logical state 21 RSTOUT direction control 5 A13 direction control 22 A20 logical state 6 A14 logical state 23 A20 direction control 7 A14 direction control 24 RESET logical state 8 A15 logical state 25 RESET direction control 9 A15 direction control 26 A21 logical state 10 A16 logical state 27 A21 direction control 11 A16 direction control 28 A22 logical state 12 A17 logical state 29 A22 direction control 13 A17 direction control 30 TEA logical state 14 CLKOUT logical state 31 TEA direction control 15 CLKOUT direction control 32 EB0 logical state 16 A18 logical state 33 EB0 direction control MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 549 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Table 21-3. Boundary-Scan Register Definition (Sheet 2 of 4) (Note: Shaded regions indicate optional pins) Freescale Semiconductor, Inc... Bit Logical State and Direction Control Bits for Each Pin Logical State and Direction Control Bits for Each Pin Bit 34 EB1 logical state 64 CS2 logical state 35 EB1 direction control 65 CS2 direction control 36 TA logical state 66 INT4 logical state 37 TA direction control 67 INT4 direction control 38 EB2 logical state 68 CS3 logical state 39 EB2 direction control 69 CS3 direction control 40 SHS logical state 70 TC0 logical state 41 SHS direction control 71 TC0 direction control 42 EB3 logical state 72 INT3 logical state 43 EB3 direction control 73 INT3 direction control 44 OE logical state 74 TC1 logical state 45 OE direction control 75 TC1 direction control 46 SS logical state 76 INT2 logical state 47 SS direction control 77 INT2 direction control 48 SCK logical state 78 INT1 logical state 49 SCK direction control 79 INT1 direction control 50 MISO logical state 80 INT0 logical state 51 MISO direction control 81 INT0 direction control 52 MOSI logical state 82 RXD1 logical state 53 MOSI direction control 83 RXD1 direction control 54 INT7 logical state 84 TXD1 logical state 55 INT7 direction control 85 TXD1 direction control 56 INT6 logical state 86 RXD2 logical state 57 INT6 direction control 87 RXD2 direction control 58 CS0 logical state 88 TC2 logical state 59 CS0 direction control 89 TC2 direction control 60 CS1 logical state 90 TXD2 logical state 61 CS1 direction control 91 TXD2 direction control 62 INT5 logical state 92 CSE0 logical state 63 INT5 direction control 93 CSE0 direction control Technical Data 550 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Boundary Scan Table 21-3. Boundary-Scan Register Definition (Sheet 3 of 4) (Note: Shaded regions indicate optional pins) Freescale Semiconductor, Inc... Bit Logical State and Direction Control Bits for Each Pin Logical State and Direction Control Bits for Each Pin Bit 94 ICOC1_0 logical state 124 D2 logical state 95 ICOC1_0 direction control 125 D2 direction control 96 CSE1 logical state 126 D3 logical state 97 CSE1 direction control 127 D3 direction control 98 R/W logical state 128 D4 logical state 99 R/W direction control 129 D4 direction control 100 ICOC1_1 logical state 130 D5 logical state 101 ICOC1_1 direction control 131 D5 direction control 102 ICOC1_2 logical state 132 D6 logical state 103 ICOC1_2 direction control 133 D6 direction control 104 ICOC1_3 logical state 134 D7 logical state 105 ICOC1_3 direction control 135 D7 direction control 106 ICOC2_0 logical state 136 D8 logical state 107 ICOC2_0 direction control 137 D8 direction control 108 ICOC2_1 logical state 138 D9 logical state 109 ICOC2_1 direction control 139 D9 direction control 110 ICOC2_2 logical state 140 D10 logical state 111 ICOC2_2 direction control 141 D10 direction control 112 ICOC2_3 logical state 142 D11 logical state 113 ICOC2_3 direction control 143 D11 direction control 114 D0 logical state 144 D12 logical state 115 D0 direction control 145 D12 direction control 116 A0 logical state 146 D13 logical state 117 A0 direction control 147 D13 direction control 118 A1 logical state 148 D14 logical state 119 A1 direction control 149 D14 direction control 120 D1 logical state 150 A3 logical state 121 D1 direction control 151 A3 direction control 122 A2 logical state 152 A4 logical state 123 A2 direction control 153 A4 direction control MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 551 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Table 21-3. Boundary-Scan Register Definition (Sheet 4 of 4) (Note: Shaded regions indicate optional pins) Freescale Semiconductor, Inc... Bit Logical State and Direction Control Bits for Each Pin Logical State and Direction Control Bits for Each Pin Bit 154 D15 logical state 177 A8 direction control 155 D15 direction control 178 A9 logical state 156 A5 logical state 179 A9 direction control 157 A5 direction control 180 D23 logical state 158 D16 logical state 181 D23 direction control 159 D16 direction control 182 A10 logical state 160 A6 logical state 183 A10 direction control 161 A6 direction control 184 D24 logical state 162 A7 logical state 185 D24 direction control 163 A7 direction control 186 D25 logical state 164 D17 logical state 187 D25 direction control 165 D17 direction control 188 A11 logical state 166 D18 logical state 189 A11 direction control 167 D18 direction control 190 D26 logical state 168 D19 logical state 191 D16 direction control 169 D19 direction control 192 D27 logical state 170 D20 logical state 193 D27 direction control 171 D20 direction control 194 D28 logical state 172 D21 logical state 195 D28 direction control 173 D21 direction control 196 D29 logical state 174 D22 logical state 197 D29 direction control 175 D22 direction control 198 D30 logical state 176 A8 logical state 199 D30 direction control Technical Data 552 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Low-Level TAP (OnCE) Module 21.12 Low-Level TAP (OnCE) Module The low-level TAP (OnCE, on-chip emulation) circuitry provides a simple, inexpensive debugging interface that allows external access to the processor's internal registers and to memory/peripherals. OnCE capabilities are controlled through a serial interface, mapped onto a JTAG test access port (TAP) protocol. Refer to Figure 21-4 for a block diagram of the OnCE. Freescale Semiconductor, Inc... NOTE: The interface to the OnCE controller and its resources is based on the TAP defined for JTAG in the IEEE 1149.1 standard. PIPELINE INFORMATION BREAKPOINT AND TRACE LOGIC OnCE CONTROLLER AND SERIAL INTERFACE PC FIFO TCLK TDI TMS TDO TRST DE BREAKPOINT REGISTERS AND COMPARATORS Figure 21-4. OnCE Block Diagram Figure 21-5 shows the OnCE (low-level TAP module) data registers in the MMC2107. MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 553 554 0x3 MEMORY BKPT COUNTER A (SHIFT) REGISTER, MBCA TRACE COUNTER (SHIFT) REGISTER, OTC OCMR, RS[4:0] = 0 LSB MSB 15 Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com PROGRAM COUNTER FIFO AND INCREMENT COUNTER (SHIFT) REGISTER, PC FIFO 0x5 0 LSB MSB 15 0x7 0 LSB BKPT ADDRESS BASE REGISTER B (SHIFT) REGISTER, BABB MSB 31 BKPT ADDRESS BASE REGISTER A (SHIFT) REGISTER, BABA 0x6 0 LSB MSB 31 0 LSB MSB 31 0x9 0 LSB MSB 31 0 LSB MSB 31 CPU SCAN CHAIN REGISTER (SHIFT) REGISTER, CPUSCR 0xa TDO (TEST DATA OUT) BKPT ADDRESS MASK REGISTER B (SHIFT) REGISTER, BAMB MUX BKPT ADDRESS MASK REGISTER A (SHIFT) REGISTER, BAMA 0x8 TDI (TEST DATA IN) 0 LSB 32 31 64 63 96 95 112 111 MSB 127 1 BIT OnCE CONTROL REGISTER (SHIFT) REGISTER, OCR 0xc BYPASS REGISTER PASSTHROUGH (SHIFT) REGISTER, BYPASS WBBR PSR PC IR CTL 0xb OnCE STATUS (SHIFT) REGISTER, OSR BCA RCA BCB SQC DR IDRE TME FRZC RCB 0xd Figure 21-5. Low-Level (OnCE) Tap Module Data Registers (DRs) 0 LSB MSB 15 MEMORY BKPT COUNTER B (SHIFT) REGISTER, MBCB 0x4 RS4-RS0 FROM ONCE CMD (INSTRUCTION) REGISTER, OCMR IN Figure 21-1 DETAILED VIEW OF OnCE DATA REGISTERS BLOCK FOUND IN FIGURE 21-1 Freescale Semiconductor, Inc... 0 LSB 6 5 4 17 16 15 14 13 12 11 10 MSB 31 0x1f 0 LSB MSB 15 BYPASS 1 BIT REGISTER PASSTHROUGH, BYPASS 0xe Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE MMC2107 - Rev. 2.0 MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Signal Descriptions Freescale Semiconductor, Inc... 21.13 Signal Descriptions The OnCE pin interface is used to transfer OnCE instructions and data to the OnCE control block. Depending on the particular resource being accessed, the CPU may need to be placed in debug mode. For resources outside of the CPU block and contained in the OnCE block, the processor is not disturbed and may continue execution. If a processor resource is required, the OnCE controller may assert a debug request (DBGRQ) to the CPU. This causes the CPU to finish the instruction being executed, save the instruction pipeline information, enter debug mode, and wait for further commands. Asserting DBGRQ causes the device to exit stop, doze, or wait mode. 21.13.1 Debug Serial Input (TDI) Data and commands are provided to the OnCE controller through the TDI pin. Data is latched on the rising edge of the TCLK serial clock. Data is shifted into the OnCE serial port least significant bit (LSB) first. 21.13.2 Debug Serial Clock (TCLK) The TCLK pin supplies the serial clock to the OnCE control block. The serial clock provides pulses required to shift data and commands into and out of the OnCE serial port. (Data is clocked into the OnCE on the rising edge and is clocked out of the OnCE serial port on the falling edge.) The debug serial clock frequency must be no greater than 50 percent of the processor clock frequency. 21.13.3 Debug Serial Output (TDO) Serial data is read from the OnCE block through the TDO pin. Data is always shifted out the OnCE serial port LSB first. Data is clocked out of the OnCE serial port on the falling edge of TCLK. TDO is three-stateable and is actively driven in the shift-IR and shift-DR controller states. TDO changes on the falling edge of TCLK. MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 555 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE 21.13.4 Debug Mode Select (TMS) The TMS input is used to cycle through states in the OnCE debug controller. Toggling the TMS pin while clocking with TCLK controls the transitions through the TAP state controller. Freescale Semiconductor, Inc... 21.13.5 Test Reset (TRST) The TRST input is used to reset the OnCE controller externally by placing the OnCE control logic in a test logic reset state. OnCE operation is disabled in the reset controller and reserved states. 21.13.6 Debug Event (DE) The DE pin is a bidirectional open drain pin. As an input, DE provides a fast means of entering debug mode from an external command controller. As an output, this pin provides a fast means of acknowledging debug mode entry to an external command controller. The assertion of this pin by a command controller causes the CPU to finish the current instruction being executed, save the instruction pipeline information, enter debug mode, and wait for commands to be entered from the TDI line. If DE was used to enter debug mode, then DE must be negated after the OnCE responds with an acknowledgment and before sending the first OnCE command. The assertion of this pin by the CPU acknowledges that it has entered debug mode and is waiting for commands to be entered from the TDI line. 21.14 Functional Description The on-chip emulation (OnCE) circuitry provides a simple, inexpensive debugging interface that allows external access to the processor's internal registers and to memory/peripherals. OnCE capabilities are controlled through a serial interface, mapped onto a JTAG test access port (TAP) protocol. Figure 21-6 shows the components of the OnCE circuitry. Technical Data 556 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Functional Description The interface to the OnCE controller and its resources are based on the TAP defined for JTAG in the IEEE 1149.1 standard. 21.14.1 Operation Freescale Semiconductor, Inc... An instruction is scanned into the OnCE module through the serial interface and then decoded. Data may then be scanned in and used to update a register or resource on a write to the resource, or data associated with a resource may be scanned out for a read of the resource. TEST-LOGIC-RESET 1 0 RUN-TEST/IDLE 1 1 SELECT DRSCAN 0 0 1 1 SELECT -- IR SCAN 0 1 CAPTURE -- DR CAPTURE -- IR 0 0 SHIFT -- DR SHIFT -- IR 0 1 0 1 1 EXIT1 -- DR 0 0 PAUSE -- DR PAUSE -- IR 0 1 EXIT2 -- DR 0 0 1 0 EXIT2 -- IR 1 1 UPDATE -- DR 1 1 EXIT1 -- IR 0 UPDATE -- IR 1 0 Figure 21-6. OnCE Controller MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 557 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE For accesses to the CPU internal state, the OnCE controller requests the CPU to enter debug mode via the CPU DBGRQ input. Once the CPU enters debug mode, as indicated by the OnCE status register, the processor state may be accessed through the CPU scan register. Freescale Semiconductor, Inc... The OnCE controller is implemented as a 16-state finite state machine, with a one-to-one correspondence to the states defined for the JTAG TAP controller. CPU registers and the contents of memory locations are accessed by scanning instructions and data into and out of the CPU scan chain. Required data is accessed by executing the scanned instructions. Memory locations may be read by scanning in a load instruction to the CPU that references the desired memory location, executing the load instruction, and then scanning out the result of the load. Other resources are accessed in a similar manner. Resources contained in the OnCE module that do not require the CPU to be halted for access may be controlled while the CPU is executing and do not interfere with normal processor execution. Accesses to certain resources, such as the PC FIFO and the count registers, while not part of the CPU, may require the CPU to be stopped to allow access to avoid synchronization hazards. If it is known that the CPU clock is enabled and running no slower than the TCLK input, there is sufficient synchronization performed to allow reads but not writes of these specific resources. Debug firmware may ensure that it is safe to access these resources by reading the OSR to determine the state of the CPU prior to access. All other cases require the CPU to be in the debug state for deterministic operation. 21.14.2 OnCE Controller and Serial Interface Figure 21-7 is a block diagram of the OnCE controller and serial interface. The OnCE command register acts as the instruction register (IR) for the TAP controller. All other OnCE resources are treated as data registers (DR) by the TAP controller. The command register is loaded by serially shifting in commands during the TAP controller shift-IR state, and is loaded during the update-IR state. The command register selects a Technical Data 558 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Functional Description OnCE resource to be accessed as a DR during the TAP controller capture-DR, shift-DR and update-DR states. TDI OnCE COMMAND REGISTER TCLK ISBKPT OnCE DECODER Freescale Semiconductor, Inc... ISTRACE OnCE TAP CONTROLLER TMS ISDR OnCE STATUS AND CONTROL REGISTERS REGISTER READ TDO REGISTER WRITE CPU CONTROL/ STATUS Figure 21-7. OnCE Controller and Serial Interface 21.14.3 OnCE Interface Signals The following paragraphs describe the OnCE interface signals to other internal blocks associated with the OnCE controller. These signals are not available externally, and descriptions are provided to improve understanding of OnCE operation. 21.14.3.1 Internal Debug Request Input (IDR) The internal debug request input is a hardware signal which is used in some implementations to force an immediate debug request to the CPU. If present and enabled, it functions in an identical manner to the control function provided by the DR control bit in the OCR. This input is maskable by a control bit in the OCR. MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 559 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE 21.14.3.2 CPU Debug Request (DBGRQ) The DBGRQ signal is asserted by the OnCE control logic to request the CPU to enter the debug state. It may be asserted for a number of different conditions. Assertion of this signal causes the CPU to finish the current instruction being executed, save the instruction pipeline information, enter debug mode, and wait for further commands. Asserting DBGRQ causes the device to exit stop, doze, or wait mode. Freescale Semiconductor, Inc... 21.14.3.3 CPU Debug Acknowledge (DBGACK) The CPU asserts the DBGACK signal upon entering the debug state. This signal is part of the handshake mechanism between the OnCE control logic and the CPU. 21.14.3.4 CPU Breakpoint Request (BRKRQ) The BRKRQ signal is asserted by the OnCE control logic to signal that a breakpoint condition has occurred for the current CPU bus access. 21.14.3.5 CPU Address, Attributes (ADDR, ATTR) The CPU address and attribute information may be used in the memory breakpoint logic to qualify memory breakpoints with access address and cycle type information. 21.14.3.6 CPU Status (PSTAT) The trace logic uses the PSTAT signals to qualify trace count decrements with specific CPU activity. 21.14.3.7 OnCE Debug Output (DEBUG) The DEBUG signal is used to indicate to on-chip resources that a debug session is in progress. Peripherals and other units may use this signal to modify normal operation for the duration of a debug session. This may involve the CPU executing a sequence of instructions solely for the purpose of visibility/system control. These instructions are not part of the normal instruction stream that the CPU would have executed had it not been placed in debug mode. Technical Data 560 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Functional Description This signal is asserted the first time the CPU enters the debug state and remains asserted until the CPU is released by a write to the OnCE command register with the GO and EX bits set, and a register specified as either no register selected or the CPUSCR. This signal remains asserted even though the CPU may enter and exit the debug state for each instruction executed under control of the OnCE controller. Freescale Semiconductor, Inc... 21.14.4 OnCE Controller Registers This section describes the OnCE controller registers: * OnCE command register (OCMR) * OnCE control register (OCR) * OnCE status register (OSR) All OnCE registers are addressed by means of the RS field in the OCMR, as shown in Table 21-4. 21.14.4.1 OnCE Command Register The OnCE command register (OCMR) is an 8-bit shift register that receives its serial data from the TDI pin. This register corresponds to the JTAG IR and is loaded when the update-IR TAP controller state is entered. It holds the 8-bit commands shifted in during the shift-IR controller state to be used as input for the OnCE decoder. The OCMR contains fields for controlling access to a OnCE resource, as well as controlling single-step operation, and exit from OnCE mode. Although the OCMR is updated during the update-IR TAP controller state, the corresponding resource is accessed in the DR scan sequence of the TAP controller, and as such, the update-DR state must be transitioned through in order for an access to occur. In addition, the update-DR state must also be transitioned through in order for the single-step and/or exit functionality to be performed, even though the command appears to have no data resource requirement associated with it. MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 561 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Bit 7 6 5 4 3 2 1 Bit 0 R/W G EX RS4 RS3 RS2 RS1 RS0 Figure 21-8. OnCE Command Register (OCMR) R/W -- Read/Write Bit 1 = Read the data in the register specified by the RS field. 0 = Write the data associated with the command into the register specified by the RS field. Freescale Semiconductor, Inc... GO -- Go Bit When the GO bit is set, the device executes the instruction in the IR register in the CPUSCR. To execute the instruction, the processor leaves debug mode, executes the instruction, and if the EX bit is cleared, returns to debug mode immediately after executing the instruction. The processor resumes normal operation if the EX bit is set. The GO command is executed only if the operation is a read/write to either the CPUSCR or to "no register selected." Otherwise, the GO bit has no effect. The processor leaves debug mode after the TAP controller update-DR state is entered. 1 = Execute instruction in IR 0 = Inactive (no action taken) EX -- Exit Bit When the EX bit is set, the processor leaves debug mode and resumes normal operation until another debug request is generated. The exit command is executed only if the GO bit is set and the operation is a read/write to the CPUSCR or a read/write to "no register selected." Otherwise, the EX bit has no effect. The processor exits debug mode after the TAP controller update-DR state is entered. 1 = Leave debug mode 0 = Remain in debug mode RS4-RS0 -- Register Select Field The RS field defines the source for the read operation or the destination for the write operation. Table 21-4 shows OnCE register addresses. Technical Data 562 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Functional Description Table 21-4. OnCE Register Addressing Freescale Semiconductor, Inc... RS4-RS0 Register Selected 00000 Reserved 00001 Reserved 00010 Reserved 00011 OTC -- OnCE trace counter 00100 MBCA -- memory breakpoint counter A 00101 MBCB -- memory breakpoint counter B 00110 PC FIFO -- program counter FIFO and increment counter 00111 BABA -- breakpoint address base register A 01000 BABB -- breakpoint address base register B 01001 BAMA -- breakpoint address mask register A 01010 BAMB -- breakpoint address mask register B 01011 CPUSCR -- CPU scan chain register 01100 Bypass -- no register selected 01101 OCR -- OnCE control register 01110 OSR -- OnCE status register 01111 Reserved (factory test control register -- do not access) 10000 Reserved (MEM_BIST -- do not access) 10001-10110 10111 11000-11110 11111 Reserved (bypass, do not access) Reserved (LSRL, do not access) Reserved (bypass, do not access) Bypass MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 563 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE 21.14.4.2 OnCE Control Register The 32-bit OnCE control register (OCR) selects the events that put the device in debug mode and enables or disables sections of the OnCE logic. Read: Bit 31 30 29 28 27 26 25 Bit 24 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 23 22 21 20 19 18 17 Bit 16 0 0 0 0 0 0 SQC1 SQC0 Write: Freescale Semiconductor, Inc... Reset: Read: Write: Reset: 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 DR IDRE TME FRZC RCB BCB4 BCB3 BCB2 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 BCB1 BCB0 RCA BCA4 BCA3 BCA2 BCA1 BCA0 0 0 0 0 0 0 0 0 Read: Write: Reset: Read: Write: Reset: = Unimplemented or reserved Figure 21-9. OnCE Control Register (OCR) SQC1 and SQC0 -- Sequential Control Field The SQC field allows memory breakpoint B and trace occurrences to be suspended until a qualifying event occurs. Test logic reset clears the SQC field. See Table 21-5. Technical Data 564 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Functional Description Table 21-5. Sequential Control Field Settings Freescale Semiconductor, Inc... SQC1 and SQC0 Meaning 00 Disable sequential control operation. Memory breakpoints and trace operation are unaffected by this field. 01 Suspend normal trace counter operation until a breakpoint condition occurs for memory breakpoint B. In this mode, memory breakpoint B occurrences no longer cause breakpoint requests to be generated. Instead, trace counter comparisons are suspended until the first memory breakpoint B occurrence. After the first memory breakpoint B occurrence, trace counter control is released to perform normally, assuming TME is set. This allows a sequence of breakpoint conditions to be specified prior to trace counting. 10 Qualify memory breakpoint B matches with a breakpoint occurrence for memory breakpoint A. In this mode, memory breakpoint A occurrences no longer cause breakpoint requests to be generated. Instead, memory breakpoint B comparisons are suspended until the first memory breakpoint A occurrence. After the first memory breakpoint A occurrence, memory breakpoint B is enabled to perform normally. This allows a sequence of breakpoint conditions to be specified. 11 Combine the 01 and 10 qualifications. In this mode, no breakpoint requests are generated, and trace count operation is enabled once a memory breakpoint B occurrence follows a memory breakpoint A occurrence if TME is set. DR -- Debug Request Bit DR requests the CPU to enter debug mode unconditionally. The PM bits in the OnCE status register indicate that the CPU is in debug mode. Once the CPU enters debug mode, it returns there even with a write to the OCMR with GO and EX set until the DR bit is cleared. Test logic reset clears the DR bit. IDRE -- Internal Debug Request Enable Bit The internal debug request (IDR) input to the OnCE control logic may not be used in all implementations. In some implementations, the IDR control input may be connected and used as an additional hardware debug request. Test logic reset clears the IDRE bit. 1 = IDR input enabled 0 = IDR input disabled MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 565 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE TME -- Trace Mode Enable Bit TME enables trace operation. Test logic reset clears the TME bit. Trace operation is also affected by the SQC field. 1 = Trace operation enabled 0 = Trace operation disabled FRZC -- Freeze Control Bit Freescale Semiconductor, Inc... This control bit is used in conjunction with memory breakpoint B registers to select between asserting a breakpoint condition when a memory breakpoint B occurs or freezing the PC FIFO from further updates when memory breakpoint B occurs while allowing the CPU to continue execution. The PC FIFO remains frozen until the FRZO bit in the OSR is cleared. 1 = Memory breakpoint B occurrence freezes PC FIFO and does not assert breakpoint condition. 0 = Memory breakpoint B occurrence asserts breakpoint condition. RCB and RCA -- Memory Breakpoint B and A Range Control Bits RCB and RDA condition enabled memory breakpoint occurrences happen when memory breakpoint matches are either within or outside the range defined by memory base address and mask. 1 = Condition breakpoint on access outside of range 0 = Condition breakpoint on access within range BCB4-BCB0 and BCA4-BCA0 -- Memory Breakpoint B and A Control Fields The BCB and BCA fields enable memory breakpoints and qualify the access attributes to select whether the breakpoint matches are recognized for read, write, or instruction fetch (program space) accesses. Test logic reset clears BCB4-BCB0 and BCA4-BCA0. Technical Data 566 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Functional Description Table 21-6. Memory Breakpoint Control Field Settings Freescale Semiconductor, Inc... BCB4-BCB0 BCA4-BCA0 Description 00000 Breakpoint disabled 00001 Qualify match with any access 00010 Qualify match with any instruction access 00011 Qualify match with any data access 00100 Qualify match with any change of flow instruction access 00101 Qualify match with any data write 00110 Qualify match with any data read 00111 Reserved 01XXX Reserved 10000 Reserved 10001 Qualify match with any user access 10010 Qualify match with any user instruction access 10011 Qualify match with any user data access 10100 Qualify match with any user change of flow access 10101 Qualify match with any user data write 10110 Qualify match with any user data read 10111 Reserved 11000 Reserved 11001 Qualify match with any supervisor access 11010 Qualify match with any supervisor instruction access 11011 Qualify match with any supervisor data access 11100 Qualify match with any supervisor change of flow access 11101 Qualify match with any supervisor data write 11110 Qualify match with any supervisor data read 11111 Reserved MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 567 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE 21.14.4.3 OnCE Status Register The 16-bit OnCE status register (OSR) indicates the reason(s) that debug mode was entered and the current operating mode of the CPU. Read: Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 HDRO DRO 0 0 Write: Freescale Semiconductor, Inc... Reset: Read: Bit 7 6 5 4 3 2 1 Bit 0 MBO SWO TO FRZO SQB SQA PM1 PM0 0 0 0 0 0 0 0 0 Write: Reset: = Unimplemented or reserved Figure 21-10. OnCE Status Register (OSR) HDRO -- Hardware Debug Request Occurrence Flag HDRO is set when the processor enters debug mode as a result of a hardware debug request from the IDR signal or the DE pin. This bit is cleared on test logic reset or when debug mode is exited with the GO and EX bits set. DRO -- Debug Request Occurrence Flag DRO is set when the processor enters debug mode and the debug request (DR) control bit in the OnCE control register is set. This bit is cleared on test logic reset or when debug mode is exited with the GO and EX bits set. MBO -- Memory Breakpoint Occurrence Flag MBO is set when a memory breakpoint request has been issued to the CPU via the BRKRQ input and the CPU enters debug mode. In some situations involving breakpoint requests on instruction prefetches, the CPU may discard the request along with the prefetch. In this case, this bit may become set due to the CPU entering debug mode for another reason. This bit is cleared on test logic reset or when debug mode is exited with the GO and EX bits set. Technical Data 568 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Functional Description SWO -- Software Debug Occurrence Flag SWO bit is set when the processor enters debug mode of operation as a result of the execution of the BKPT instruction. This bit is cleared on test logic reset or when debug mode is exited with the GO and EX bits set. TO -- Trace Count Occurrence Flag Freescale Semiconductor, Inc... TO is set when the trace counter reaches zero with the trace mode enabled and the CPU enters debug mode. This bit is cleared on test logic reset or when debug mode is exited with the GO and EX bits set. FRZO -- FIFO Freeze Occurrence Flag FRZO is set when a FIFO freeze occurs. This bit is cleared on test logic reset or when debug mode is exited with the GO and EX bits set. SQB -- Sequential Breakpoint B Arm Occurrence Flag SQB is set when sequential operation is enabled and a memory breakpoint B event has occurred to enable trace counter operation. This bit is cleared on test logic reset or when debug mode is exited with the GO and EX bits set. SQA -- Sequential Breakpoint A Arm Occurrence Flag SQA is set when sequential operation is enabled and a memory breakpoint A event has occurred to enable memory breakpoint B operation. This bit is cleared on test logic reset or when debug mode is exited with the GO and EX bits set. PM1 and PM0 -- Processor Mode Field These flags reflect the processor operating mode. They allow coordination of the OnCE controller with the CPU for synchronization. Table 21-7. Processor Mode Field Settings PM1 and PM0 Meaning 00 Processor in normal mode 01 Processor in stop, doze, or wait mode 10 Processor in debug mode 11 Reserved MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 569 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE 21.14.5 OnCE Decoder (ODEC) The ODEC receives as input the 8-bit command from the OCMR and status signals from the processor. The ODEC generates all the strobes required for reading and writing the selected OnCE registers. 21.14.6 Memory Breakpoint Logic Freescale Semiconductor, Inc... Memory breakpoints can be set for a particular memory location or on accesses within an address range. The breakpoint logic contains an input latch for addresses, registers that store the base address and address mask, comparators, attribute qualifiers, and a breakpoint counter. Figure 21-11 illustrates the basic functionality of the OnCE memory breakpoint logic. This logic is duplicated to provide two independent breakpoint resources. ADDR[31:0] ATTR BC[4:0], RCx MEMORY ADDRESS LATCH DSCK DSO DSI ADDRESS COMPARATOR MATCH MEMORY BREAKPOINT QUALIFICATION ADDRESS BASE REGISTER X BREAKPOINT MATCH OCCURRED ADDRESS MASK REGISTER X DEC BREAKPOINT COUNTER COUNT = 0 ISBKPTx Figure 21-11. OnCE Memory Breakpoint Logic Technical Data 570 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Functional Description Freescale Semiconductor, Inc... Address comparators can be used to determine where a program may be getting lost or when data is being written to areas which should not be written. They are also useful in halting a program at a specific point to examine or change registers or memory. Using address comparators to set breakpoints enables the user to set breakpoints in RAM or ROM in any operating mode. Memory accesses are monitored according to the contents of the OCR. The address comparator generates a match signal when the address on the bus matches the address stored in the breakpoint address base register, as masked with individual bit masking capability provided by the breakpoint address mask register. The address match signal and the access attributes are further qualified with the RCx4-RCx0 and BCx4-BCx0 control bits. This qualification is used to decrement the breakpoint counter conditionally if its contents are non-zero. If the contents are zero, the counter is not decremented and the breakpoint event occurs (ISBKPTx asserted). 21.14.6.1 Memory Address Latch (MAL) The MAL is a 32-bit register that latches the address bus on every access. 21.14.6.2 Breakpoint Address Base Registers The 32-bit breakpoint address base registers (BABA and BABB) store memory breakpoint base addresses. BABA and BABB can be read or written through the OnCE serial interface. Before enabling breakpoints, the external command controller should load these registers. 21.14.7 Breakpoint Address Mask Registers The 32-bit breakpoint address mask registers (BAMA and BAMB) registers store memory breakpoint base address masks. BAMA and BAMB can be read or written through the OnCE serial interface. Before enabling breakpoints, the external command controller should load these registers. MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 571 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE 21.14.7.1 Breakpoint Address Comparators The breakpoint address comparators are not externally accessible. Each compares the memory address stored in MAL with the contents of BABx, as masked by BAMx, and signals the control logic when a match occurs. Freescale Semiconductor, Inc... 21.14.7.2 Memory Breakpoint Counters The 16-bit memory breakpoint counter registers (MBCA and MBCB) are loaded with a value equal to the number of times, minus one, that a memory access event should occur before a memory breakpoint is declared. The memory access event is specified by the RCx4-RCx0 and BCx4-BCx0 bits in the OCR and by the memory base and mask registers. On each occurrence of the memory access event, the breakpoint counter, if currently non-zero, is decremented. When the counter has reached the value of zero and a new occurrence takes place, the ISBKPTx signal is asserted and causes the CPU's BRKRQ input to be asserted. The MBCx can be read or written through the OnCE serial interface. Anytime the breakpoint registers are changed, or a different breakpoint event is selected in the OCR, the breakpoint counter must be written afterward. This assures that the OnCE breakpoint logic is reset and that no previous events will affect the new breakpoint event selected. 21.14.8 OnCE Trace Logic The OnCE trace logic allows the user to execute instructions in single or multiple steps before the device returns to debug mode and awaits OnCE commands from the debug serial port. The OnCE trace logic is independent of the M*CORE trace facility, which is controlled through the trace mode bits in the M*CORE processor status register. The OnCE trace logic block diagram is shown in Figure 21-12. Technical Data 572 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Functional Description 21.14.8.1 OnCE Trace Counter The OnCE trace counter register (OTC) is a 16-bit counter that allows more than one instruction to be executed in real time before the device returns to debug mode. This feature helps the software developer debug sections of code that are time-critical. The trace counter also enables the user to count the number of instructions executed in a code segment. END OF INSTRUCTION DSI Freescale Semiconductor, Inc... DSO DSCK DEC OnCE TRACE COUNTER COUNT = 0 ISTRACE Figure 21-12. OnCE Trace Logic Block Diagram The OTC register can be read, written, or cleared through the OnCE serial interface. If N instructions are to be executed before entering debug mode, the trace counter should be loaded with N - 1. N must not equal zero unless the sequential breakpoint control capability is being used. In this case a value of zero (indicating a single instruction) is allowed. A hardware reset clears the OTC. MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 573 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE 21.14.8.2 Trace Operation To initiate trace mode operation: Freescale Semiconductor, Inc... 1. Load the OTC register with a value. This value must be non-zero, unless sequential breakpoint control operation is enabled in the OCR register. In this case, a value of zero (indicating a single instruction) is allowed. 2. Initialize the program counter and instruction register in the CPUSCR with values corresponding to the start location of the instruction(s) to be executed real-time. 3. Set the TME bit in the OCR. 4. Release the processor from debug mode by executing the appropriate command issued by the external command controller. When debug mode is exited, the counter is decremented after each execution of an instruction. Interrupts can be serviced, and all instructions executed (including interrupt services) will decrement the trace counter. When the trace counter decrements to zero, the OnCE control logic requests that the processor re-enter debug mode, and the trace occurrence bit TO in the OSR is set to indicate that debug mode has been requested as a result of the trace count function. The trace counter allows a minimum of two instructions to be specified for execution prior to entering trace (specified by a count value of one), unless sequential breakpoint control operation is enabled in the OCR. In this case, a value of zero (indicating a single instruction) is allowed. 21.14.9 Methods of Entering Debug Mode The PM status field in the OSR indicates that the CPU has entered debug mode. The following paragraphs discuss conditions that invoke debug mode. 21.14.9.1 Debug Request During RESET When the DR bit in the OCR is set, assertion of RESET causes the device to enter debug mode. In this case the device may fetch the reset Technical Data 574 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Functional Description vector and the first instruction of the reset exception handler but does not execute an instruction before entering debug mode. Freescale Semiconductor, Inc... 21.14.9.2 Debug Request During Normal Activity Setting the DR bit in the OCR during normal device activity causes the device to finish the execution of the current instruction and then enter debug mode. Note that in this case the device completes the execution of the current instruction and stops after the newly fetched instruction enters the CPU instruction latch. This process is the same for any newly fetched instruction, including instructions fetched by interrupt processing or those that will be aborted by interrupt processing. 21.14.9.3 Debug Request During Stop, Doze, or Wait Mode Setting the DR bit in the OCR when the device is in stop, doze, or wait mode (for instance, after execution of a STOP, DOZE, or WAIT instruction) causes the device to exit the low-power state and enter the debug mode. Note that in this case, the device completes the execution of the STOP, DOZE, or WAIT instruction and halts after the next instruction enters the instruction latch. 21.14.9.4 Software Request During Normal Activity Executing the BKPT instruction when the FDB (force debug enable mode) control bit in the control state register is set causes the CPU to enter debug mode after the instruction following the BKPT instruction has entered the instruction latch. 21.14.10 Enabling OnCE Trace Mode When the OnCE trace mode mechanism is enabled and the trace count is greater than zero, the trace counter is decremented for each instruction executed. Completing execution of an instruction when the trace counter is zero causes the CPU to enter debug mode. NOTE: Only instructions actually executed cause the trace counter to decrement. An aborted instruction does not decrement the trace counter and does not invoke debug mode. MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 575 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE 21.14.11 Enabling OnCE Memory Breakpoints Freescale Semiconductor, Inc... When the OnCE memory breakpoint mechanism is enabled with a breakpoint counter value of zero, the device enters debug mode after completing the execution of the instruction that caused the memory breakpoint to occur. In case of breakpoints on instruction fetches, the breakpoint is acknowledged immediately after the execution of the fetched instruction. In case of breakpoints on data memory addresses, the breakpoint is acknowledged after the completion of the memory access instruction. 21.14.12 Pipeline Information and Write-Back Bus Register A number of on-chip registers store the CPU pipeline status and are configured in the CPU scan chain register (CPUSCR) for access by the OnCE controller. The CPUSCR is used to restore the pipeline and resume normal device activity upon return from debug mode. The CPUSCR also provides a mechanism for the emulator software to access processor and memory contents. Figure 21-13 shows the block diagram of the pipeline information registers contained in the CPUSCR. 31 0 TDO WBBR 31 0 PSR 31 0 PC 15 TDI 0 15 CTL 0 IR Figure 21-13. CPU Scan Chain Register (CPUSCR) Technical Data 576 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Functional Description 21.14.12.1 Program Counter Register The program counter register (PC) is a 32-bit latch that stores the value in the CPU program counter when the device enters debug mode. The CPU PC is affected by operations performed during debug mode and must be restored by the external command controller when the CPU returns to normal mode. Freescale Semiconductor, Inc... 21.14.12.2 Instruction Register The instruction register (IR) provides a mechanism for controlling the debug session. The IR allows the debug control block to execute selected instructions; the debug control module provides single-step capability. When scan-out begins, the IR contains the opcode of the next instruction to be executed at the time debug mode was entered. This opcode must be saved in order to resume normal execution at the point debug mode was entered. On scan-in, the IR can be filled with an opcode selected by debug control software in preparation for exiting debug mode. Selecting appropriate instructions allows a user to examine or change memory locations and processor registers. Once the debug session is complete and normal processing is to be resumed, the IR can be loaded with the value originally scanned out. 21.14.12.3 Control State Register The control state register (CTL) is used to set control values when debug mode is exited. On scan-in, this register is used to control specific aspects of the CPU. Certain bits reflect internal processor status and should be restored to their original values. The CTL register is a 16-bit latch that stores the value of certain internal CPU state variables before debug mode is entered. This register is affected by the operations performed during the debug session and should be restored by the external command controller when returning to normal mode. In addition to saved internal state variables, the bits are used by emulation firmware to control the debug process. MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 577 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Reserved bits represent the internal processor state. Restore these bits to their original value after a debug session is completed, for example, when a OnCE command is issued with the GO and EX bits set and not ignored. Set these bits to 1s while instructions are executed during a debug session. Bit 15 14 13 12 11 10 9 Bit 8 RSVD RSVD RSVD RSVD RSVD RSVD RSVD FFY Read: Write: Freescale Semiconductor, Inc... Reset: 0 Bit 7 6 5 4 3 2 1 Bit 0 FDB SZ1 SZ0 TC2 TC1 TC0 RSVD RSVD 0 0 0 0 0 0 Read: Write: Reset: Figure 21-14. Control State Register (CTL) FFY -- Feed Forward Y Operand Bit This control bit is used to force the content of the WBBR to be used as the Y operand value of the first instruction to be executed following an update of the CPUSCR. This gives the debug firmware the capability of updating processor registers by initializing the WBBR with the desired value, setting the FFY bit, and executing a MOV instruction to the desired register. FDB -- Force Debug Enable Mode Bit Setting this control bit places the processor in debug enable mode. In debug enable mode, execution of the BKPT instruction as well as recognition of the BRKRQ input causes the processor to enter debug mode, as if the DBGRQ input had been asserted. SZ1 and SZ0 -- Prefetch Size Field This control field is used to drive the CPU SIZ1 and SIZ0 outputs on the first instruction pre-fetch caused by issuing a OnCE command with the GO bit set and not ignored. It should be set to indicate a 16-bit size, for example, 0b10. This field should be restored to its original value after a debug session is completed, for example, when a OnCE command is issued with the GO and EX bits set and not ignored. Technical Data 578 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Functional Description TC -- Prefetch Transfer Code Freescale Semiconductor, Inc... This control field is used to drive the CPU TC2-TC0 outputs on the first instruction pre-fetch caused by issuing a OnCE command with the GO bit set and not ignored. It should typically be set to indicate a supervisor instruction access, for example, 0b110. This field should be restored to its original value after a debug session is completed, for example, when a OnCE command is issued with the GO and EX bits set and not ignored. 21.14.12.4 Writeback Bus Register The writeback bus register (WBBR) is a means of passing operand information between the CPU and the external command controller. Whenever the external command controller needs to read the contents of a register or memory location, it forces the device to execute an instruction that brings that information to WBBR. For example, to read the content of processor register r0, a MOV r0,r0 instruction is executed, and the result value of the instruction is latched into the WBBR. The contents of WBBR can then be delivered serially to the external command controller. To update a processor resource, this register is initialized with a data value to be written, and a MOV instruction is executed which uses this value as a write-back data value. The FFY bit in the CTL register forces the value of the WBBR to be substituted for the normal source value of a MOV instruction, thus allowing updates to processor registers to be performed. 21.14.12.5 Processor Status Register The processor status register (PSR) is a 32-bit latch used to read or write the M*CORE processor status register. Whenever the external command controller needs to save or modify the contents of the M*CORE processor status register, the PSR is used. This register is affected by the operations performed in debug mode and must be restored by the external command controller when returning to normal mode. MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 579 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE 21.14.13 Instruction Address FIFO Buffer (PC FIFO) To ease debugging activity and keep track of program flow, a first-in-first-out (FIFO) buffer stores the addresses of the last eight instruction change-of-flow prefetches that were issued. Freescale Semiconductor, Inc... The FIFO is a circular buffer containing eight 32-bit registers and one 3-bit counter. All the registers have the same address, but any read access to the FIFO address causes the counter to increment and point to the next FIFO register. The registers are serially available to the external command controller through the common FIFO address. Figure 21-15 shows the structure of the PC FIFO. INSTRUCTION FETCH ADDRESS PC FIFO REGISTER 0 PC FIFO REGISTER 1 PC FIFO REGISTER 2 CIRCULAR BUFFER POINTER PC FIFO REGISTER 3 PC FIFO REGISTER 4 PC FIFO REGISTER 5 PC FIFO REGISTER 6 PC FIFO REGISTER 7 PC FIFO SHIFT REGISTER TCLK TDO Figure 21-15. OnCE PC FIFO Technical Data 580 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Functional Description Freescale Semiconductor, Inc... The FIFO is not affected by operations performed in debug mode, except for incrementing the FIFO pointer when the FIFO is read. When debug mode is entered, the FIFO counter points to the FIFO register containing the address of the oldest of the eight change-of-flow pre-fetches. The first FIFO read obtains the oldest address, and the following FIFO reads return the other addresses from the oldest to the newest, in order of execution. To ensure FIFO coherence, a complete set of eight reads of the FIFO must be performed. Each read increments the FIFO pointer, causing it to point to the next location. After eight reads, the pointer points to the same location as before the start of the read procedure. 21.14.14 Reserved Test Control Registers The reserved test control registers (MEM_BIST, FTCR, and LSRL) are reserved for factory testing. CAUTION: To prevent damage to the device or system, do not access these registers during normal operation. 21.14.15 Serial Protocol The serial protocol permits an efficient means of communication between the OnCE external command controller and the MCU. Before starting any debugging activity, the external command controller must wait for an acknowledgment that the device has entered debug mode. The external command controller communicates with the device by sending 8-bit commands to the OnCE command register and 16 to 128 bits of data to one of the other OnCE registers. Both commands and data are sent or received LSB first. After sending a command, the external command controller must wait for the processor to acknowledge execution of certain commands before it can properly access another OnCE register. MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 581 Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE 21.14.16 OnCE Commands Freescale Semiconductor, Inc... The OnCE commands can be classified as: * Read commands (the device delivers the required data) * Write commands (the device receives data and writes the data in one of the OnCE registers) * Commands with no associated data transfers 21.14.17 Target Site Debug System Requirements A typical debug environment consists of a target system in which the MCU resides in the user-defined hardware. The external command controller acts as the medium between the MCU target system and a host computer. The external command controller circuit acts as a serial debug port driver and host computer command interpreter. The controller issues commands based on the host computer inputs from a user interface program which communicates with the user. 21.14.18 Interface Connector for JTAG/OnCE Serial Port Figure 21-16 shows the recommended connector pinout and interface requirements for debug controllers that access the JTAG/OnCE port. The connector has two rows of seven pins with 0.1-inch center-to-center spacing between pins in each row and each column. Technical Data 582 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. JTAG Test Access Port and OnCE Functional Description TARGET VDD GND TOP VIEW (0.1 INCH CENTER-TO-CENTER) 10 k TDI TDO 10 k TCLK 10 k GPIO/SI Freescale Semiconductor, Inc... 10 k TARGET_RESET WIRED OR WITH TARGET RESET CIRCUIT. THIS SIGNAL MUST BE ABLE TO ASSERT/MONITOR SYSTEM RESET. TARGET VDD GPIO/SO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 KEY (No Connect) TMS 10 k DE 10 k TRST 10 k TARGET VDD Note: GPIO/SI and GPIO/SO are not required for OnCE operation at this time. These pins can be used for high-speed downloads with a recommended interface. Figure 21-16. Recommended Connector Interface to JTAG/OnCE Port MMC2107 - Rev. 2.0 MOTOROLA Technical Data JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com 583 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... JTAG Test Access Port and OnCE Technical Data 584 MMC2107 - Rev. 2.0 JTAG Test Access Port and OnCE For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 22. Electrical Specifications Freescale Semiconductor, Inc... 22.1 Contents 22.2 22.3 22.4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 585 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . 586 Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 587 22.5 22.6 22.7 22.8 22.9 22.10 22.11 22.12 22.13 22.14 Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 587 Electrostatic Discharge (ESD) Protection . . . . . . . . . . . . . . . . 587 DC Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 588 PLL Electrical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . 590 QADC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . .591 FLASH Memory Characteristics . . . . . . . . . . . . . . . . . . . . . . .594 External Interface Timing Characteristics . . . . . . . . . . . . . . . . 596 Reset and Configuration Override Timing . . . . . . . . . . . . . . . 601 SPI Timing Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . 602 OnCE, JTAG, and Boundary Scan Timing . . . . . . . . . . . . . . . 605 22.2 Introduction This section contains electrical and timing specifications. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Electrical Specifications For More Information On This Product, Go to: www.freescale.com 585 Freescale Semiconductor, Inc. Electrical Specifications 22.3 Absolute Maximum Ratings Maximum ratings are the extreme limits to which the MCU can be exposed without permanently damaging it. See Table 22-1. Freescale Semiconductor, Inc... The MCU contains circuitry to protect the inputs against damage from high static voltages; however, do not apply voltages higher than those shown in the table. Keep VIn and VOut within the range VSS (VIn or VOut) VDD. Connect unused inputs to the appropriate voltage level, either VSS or VDD. This device is not guaranteed to operate properly at the maximum ratings. Refer to 22.7 DC Electrical Specifications for guaranteed operating conditions. Table 22-1. Absolute Maximum Ratings Parameter Symbol Value Unit VDD -0.3 to +4.0 V VDDSYN -0.3 to +4.0 V RAM memory standby supply voltage VSTBY -0.3 to + 4.0 V FLASH memory supply voltage VDDF -0.3 to +4.0 V FLASH memory program/erase supply voltage VPP -0.3 to + 6.0 V Analog supply voltage VDDA -0.3 to +6.0 V Analog reference supply voltage VRH -0.3 to +6.0 V Analog ESD protection voltage VDDH -0.3 to +6.0 V Digital input voltage(1) VIN -0.3 to + 4.0 V Analog input voltage VAIN -0.3 to + 6.0 V ID 25 mA TA (TL to TH) -40 to 85 C TSTG -65 to 150 C Supply voltage Clock synthesizer supply voltage Instantaneous maximum current single pin limit (applies to all pins)(2), (3) Operating temperature range (packaged) Storage temperature range 1. Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate resistance values for positive and negative clamp voltages, then use the larger of the two values. 2. All functional non-supply pins are internally clamped to VSS and V DD. 3. Power supply must maintain regulation within operating VDD range during instantaneous and operating maximum current conditions. If positive injection current (Vin > VDD) is greater than IDD, the injection current may flow out of VDD and could result in external power supply going out of regulation. Ensure external VDD load will shunt current greater than maximum injection current. This will be the greatest risk when the MCU is not consuming power (ex; no clock). Technical Data 586 MMC2107 - Rev. 2.0 Electrical Specifications For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Electrical Specifications Thermal Characteristics 22.4 Thermal Characteristics Table 22-2. Thermal Characteristics Parameter Thermal Resistance Plastic 100-pin LQFP surface mount Plastic 144-pin LQFP surface mount Symbol Value Unit JA 43.5 46.1 C/W Freescale Semiconductor, Inc... 22.5 Power Dissipation The average chip-junction temperature (TJ) in C can be obtained from: TJ = TA + PD x JA (1) where: = Ambient temperature, C TA JA = Package thermal resistance, junction-to-ambient, C/W PD = PINT + PI/O PINT = IDD x VDD, watts -- chip internal power PI/O = Power dissipation on input and output pins -- user determined For most applications, PI/O < PINT and can be neglected. An approximate relationship between PD and TJ (if PI/O is neglected) is: PD = K / (TJ + 273C) (2) Solving equations 1 and 2 for K gives: K = PD x (TA + 273C) + JA x PD 2 (3) where K is a constant pertaining to the particular part. K can be determined from equation (3) by measuring PD (at equilibrium) for a known TA. Using this value of K, the values of PD and TJ can be obtained by solving equations (1) and (2) iteratively for any value of TA. 22.6 Electrostatic Discharge (ESD) Protection Table 22-3. ESD Protection Characteristics Parameter(1) Symbol Value Units ESD target for human body model HBM 2000 V ESD target for machine model MM 200 V RSeries 1500 W C 100 pF RSeries 0 W C 200 pF HBM circuit description MM circuit description 1. All ESD testing is in conformity with CDF-AEC-Q100 Stress Test Qualification for Automotive Grade Integrated Circuits. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Electrical Specifications For More Information On This Product, Go to: www.freescale.com 587 Freescale Semiconductor, Inc. Electrical Specifications 22.7 DC Electrical Specifications Table 22-4. DC Electrical Specifications (VSS = VSSYN = VSSF = VSSA = 0 V, TA = TL to TH) Freescale Semiconductor, Inc... Parameter Symbol Min Max Unit Input high voltage VIH 0.7 x VDD VDD +0.3 V Input low voltage VIL VSS -0.3 0.35 x VDD V Input hysteresis VHYS 0.06 x VDD -- V Input leakage current, Vin = VDD or VSS, input-only pins IIn -1.0 1.0 A High impedance (off-state) leakage current Vin = VDD or VSS, all input/output and output pins IOZ -1.0 1.0 A Output high voltage IOH = -2.0 mA, all input/output and all output pins VOH VDD -0.5 -- V Output low voltage IOL = 2.0 mA, all input/output and all output pins VOL -- 0.5 V Weak internal pullup device current, tested at VIL maximum IAPU -10 -130 A Input capacitance All input-only pins All input/output (three-state) pins CIn -- -- 7 7 pF Load Capacitance 50% partial drive 100% full drive CL -- -- 25 50 pF VDD 2.7 3.6 V VDDSYN 2.7 3.6 V VSTBY 0.0 2.7 3.6 3.6 V 2.7 3.135 3.6 3.465 V VDDF -0.35 4.75 5.25 5.25 V -- -- -- -- -- 200 175 75 75 100 mA mA mA mA A Supply voltage, includes core modules and pads Clock synthesizer supply voltage RAM memory standby supply voltage Normal operation: VDD > VSTBY -0.3 V Standby mode: VDD < VSTBY -0.3 V FLASH memory supply voltage(1) Read Program or erase FLASH memory program/erase supply voltage Read Program or erase Operating supply current(2), (4) Master mode Single-chip mode Wait mode Doze mode Stop mode VDDF VPP IDD Technical Data 588 MMC2107 - Rev. 2.0 Electrical Specifications For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Electrical Specifications DC Electrical Specifications Table 22-4. DC Electrical Specifications (Continued) (VSS = VSSYN = VSSF = VSSA = 0 V, TA = TL to TH) Parameter Freescale Semiconductor, Inc... Clock synthesizer supply current(3) Normal operation 8-MHz crystal, VCO on, Max fsys Stop (OSC and PLL enabled) Stop (OSC enable, PLL disabled) Stop (OSC and PLL disabled) Symbol IDDSYN Min Max Unit -- -- -- -- 4 2 1 10 mA mA mA A -- -- -- 10 7 20 A mA A -- -- -- -- 50 50 20 10 mA mA mA A RAM memory standby supply current(4) Normal operation: VDD > VSTBY - 0.3 V Transient condition: VSTBY -0.3 V > VDD > VSS + 0.5 V Standby operation: VDD < VSS + 0.5 V ISTBY FLASH memory supply current(4) Read Program or erase Disabled Stop IDDF Flash memory program / erase supply current(4) Read Program or erase Disabled and stop IPP -- -- -- 100 100 10 A mA A IDDA -- -- 15.0 10.0 mA A -1.0 -10 1.0 10 Analog supply current(4) Normal operation Low-power stop DC injection current(4), (5), (6) VNEGCLAMP = VSS - 0.3 V, VPOSCLAMP = VDD + 0.3 Single pin limit Total MCU limit, includes sum of all stressed pins IIC mA 1. A voltage of at least VDDF -0.35 V must be applied at all times to the VPP pin or damage to the FLASH module can occur The FLASH can be damaged by power on and power off VPP transients. V PP must not rise to programming level while VDDF is below the specified minimum value, and must not fall below the minimum specified value while VDDF is applied. 2. Current measured at maximum system clock frequency, all modules active, and default drive strength with matching load. 3. Total device current consumption = IDD + IDDSYN + ISTBY + IDDF + IPP + IDDA 4. All functional non-supply pins are internally clamped to VSS and their respective VDD. 5. Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate resistance values for positive and negative clamp voltages, then use the larger of the two values. 6. Power supply must maintain regulation within operating VDD range during instantaneous and operating maximum current conditions. If positive injection current (Vin > VDD) is greater than IDD, the injection current may flow out of VDD and could result in external power supply going out of regulation. Ensure external VDD load will shunt current greater than maximum injection current. This will be the greatest risk when the MCU is not consuming power. Examples are: if no system clock is present, or if clock rate is very low which would reduce overall power consumption. Also, at power-up, system clock is not present during the power-up sequence until the PLL has attained lock. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Electrical Specifications For More Information On This Product, Go to: www.freescale.com 589 Freescale Semiconductor, Inc. Electrical Specifications 22.8 PLL Electrical Specifications Table 22-5. PLL Electrical Specifications (VDD and VDDSYN = 2.7 to 3.6 V, VSS = VSSSYN = 0 V, TA = TL to TH) Freescale Semiconductor, Inc... Parameter Symbol Min Max 2 2 10 10.0 33.0 33.0 Unit PLL reference frequency range Crystal reference External reference 1:1 mode fref System frequency(1) External reference On-chip PLL frequency fsys 0 fref/64 33.0 33.0 MHz Loss of reference frequency(2) fLOR 100 250 kHz fSCM 0.5 15 MHz EXTAL input high voltage Crystal mode All other modes (1:1, bypass, external) VIHEXT VDDSYN -1.0 2.0 VDDSYN VDDSYN V EXTAL input low voltage Crystal mode All other modes (1:1, bypass, external) VILEXT VSSSYN VSSSYN 1.0 0.8 V PLL lock time(4), (5) tLPLL -- 200 s Powerup-to-lock Time(4), (5) Without crystal reference tLPLK -- 200 s 1:1 clock skew (between CLKOUT and EXTAL)(6) tSkew -2 2 ns tdc 40 60 % fsys Frequency un-LOCK range fUL -1.5 1.5 % fsys Frequency LOCK range fLCK -0.75 0.75 % fsys -- -- 5 0.01 % fsys Self-clocked mode frequency Duty cycle of reference (3) (4) CLKOUT period jitter(7) Measured at fsys maximum Peak-to-peak jitter (clock edge to clock edge) Long-term jitter (averaged over 2-ms interval) CJitter MHz 1. All internal registers retain data at 0 Hz. 2. Loss of reference frequency is the reference frequency detected internally, which transitions the PLL into self-clocked mode. 3. Self-clocked mode frequency is the frequency that the PLL operates at when the reference frequency falls below fLOR with default MFD/RFD settings. 4. This specification applies to the period required for the PLL to relock after changing the MFD frequency control bits in the synthesizer control register (SYNCR). 5. Assuming a reference is available at power-up, lock time is measured from the time V DD and VDDSYN are valid to RSTOUT negating. If the crystal oscillator is being used as the reference for the PLL, then the crystal startup time must be added to the PLL lock time to determine the total startup time. 6. PLL is operating in 1:1 PLL mode. 7. Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum fsys. Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise injected into the PLL circuitry via VDDSYN and VSSSYN and variation in crystal oscillator frequency increase the C Jitter percentage for a given interval. Technical Data 590 MMC2107 - Rev. 2.0 Electrical Specifications For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Electrical Specifications QADC Electrical Characteristics 22.9 QADC Electrical Characteristics The QADC electrical characteristics are shown in Table 22-6, Table 22-7, and Table 22-8. Table 22-6. QADC Absolute Maximum Ratings Freescale Semiconductor, Inc... Parameter Symbol Min Max Unit Analog supply, with reference to VSSA VDDA -0.3 6.0 V Internal digital supply with reference to VSS VDD -0.3 4.0 V Maximum analog reference voltage with respect to VRL VRH -0.3 6.0 V VSS differential voltage VSS - VSSA -0.1 0.1 V VDD differential voltage (1) VDD - VDDA -6.0 4.0 V VREF differential voltage VRH - VRL -0.3 6.0 V VRH to VDDA differential voltage(2) VRH - VDDA -6.0 6.0 V VRL to VSSA differential voltage VRL - VSSA -0.3 0.3 V VDDH to VDDA differential voltage VDDH - VDDA -1.0 1.0 V Maximum input current(2), (3), (4) IMA -25 25 mA 1. Refers to allowed random sequencing of power supplies 2. Transitions within the limit do not affect device reliability or cause permanent damage. Exceeding limit may cause permanent conversion error on stressed channels and on unstressed channels. 3. Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate resistance values using VPOSCLAMP = VDDA + 0.3 V and VNEGCLAMP = -0.3 V, then use the larger of the calculated values. 4. Condition applies to one pin at a time. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Electrical Specifications For More Information On This Product, Go to: www.freescale.com 591 Freescale Semiconductor, Inc. Electrical Specifications Table 22-7. QADC Electrical Specifications (VDDH = VDDA = 5.0 V 0.5 V, VDD = 2.7 to 3.6 V, VSS and VSSA = 0 Vdc, fQCLK = 2.0 MHz, TA = TL to TH) Parameter(1) Symbol Min Max Unit VDDA 4.5 5.5 V VSS - VSSA -100 100 mV Reference voltage low(2) VRL VSSA VSSA + 0.1 V Reference voltage high (3) VRH VDDA - 0.1 VDDA V VRH - VRL 4.5 5.5 V VINDC VSSA -0.3 VDDA + 0.3 V Input high voltage, PQA and PQB VIH 0.7 x VDDH VDDH + 0.3 V Input low voltage, PQA and PQB VIL VSSA - 0.3 0.35 x VDDH V Input hysteresis, PQA and PQB(3) VHYS 0.6 x VDDH -- V VOL -- -- 0.4 0.2 V Analog supply Freescale Semiconductor, Inc... VSS differential voltage VREF differential voltage Input voltage Output low voltage, PQA(4) IOL = 5.3 mA IOL = 10.0 A Output high voltage, PQA(5) IOH = 2.0 mA IOH = 10.0 A VOH VDD -0.4 VDD -0.2 -- -- V Analog supply current Normal operation (5) Low-power stop IDDA -- -- 15.0 10.0 mA A Reference supply current, DC Reference supply current, transient IRef -- -- 250 2.0 A mA Load capacitance, PQA CL -- 50 pF IOff -200 -150 200 150 nA -- -- -- 15 10 5 Input current, channel off PQA, PQB (6) Total input capacitance PQA not sampling PQB not sampling Incremental capacitance added during sampling CIn pF 1. QADC converter specifications are only guaranteed for V DDH and VDDA = 5.0 V 0.5 V. VDDH and V DDA may be powered down to 2.7 V with only GPIO functions supported. 2. To obtain full-scale, full-range results, VSSA V RL VINDC VRH VDDA 3. Parameter applies to the following pins: Port A: PQA[7:0]/AN[59:58]/ETRIG[2:1] Port B: PQB[7:0]/AN[3:0]/AN[51:48]/AN[Z:W] 4. Full driver (push-pull) 5. Current measured at maximum system clock frequency with QADC active 6. Maximum leakage occurs at maximum operating temperature. Current decreases by approximately one-half for each 8C to 12C, in the ambient temperature range of -40C to +85C. Technical Data 592 MMC2107 - Rev. 2.0 Electrical Specifications For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Electrical Specifications QADC Electrical Characteristics Table 22-8. QADC Conversion Specifications (VDDH and VDDA = 5.0 Vdc 0.5 V, VDD = 2.7 to 3.6 V, VSS = VSSA = 0 Vdc, VRH - VRL = 5 V 0.5 V, TA = TL to TH) Freescale Semiconductor, Inc... No. Parameter frequency(1) Symbol Min Max Unit fQCLK 0.5 2.1 MHz CC 14 28 QCLK cycles tCONV 7.0 14.0 s 1 QADC clock (QCLK) 2 Conversion cycles 3 Conversion time, fQCLK = 2.0 MHz Minimum = CCW/IST =%00 Maximum = CCW/IST =%11 4 Stop mode recovery time tSR -- 10 s 5 Resolution(2) -- 5 -- mV 6 Absolute (total unadjusted) error(3), (4), (5) fQCLK = 2.0 MHz(2), two clock input sample time AE -2 2 Counts 7 Disruptive input injection current(6), (7), (8) IINJ(9) -1 1 mA 8 Current coupling ratio(10) PQA PQB K -- -- 8x10 -5 8x10 -5 m 9 Incremental error due to injection current All channels have same 10 k < RS <100 k Channel under test has RS = 10 k, IINJ = IINJMAX, IINJMIN EINJ -- -- -- +1.0 +1.0 +1.0 Counts Counts Counts 10 Source impedance at input(11) RS -- 100 k 11 Incremental capacitance during sampling(12) CSAMP -- 5 pF 1. Conversion characteristics vary with fQCLK rate. Reduced conversion accuracy occurs at max fQCLK rate. Using the QADC pins as GPIO functions during conversions may result in degraded results. 2. At VRH - V RL = 5.12 V, one count = 5 mV 3. Accuracy tested and guaranteed at VRH - VRL = 5.0 V 0.5 V 4. Absolute error includes 1/2 count (~2.5 mV) of inherent quantization error and circuit (differential, integral, and offset) error. Specification assumes that adequate low-pass filtering is present on analog input pins -- capacitive filter with 0.01 F to 0.1 F capacitor between analog input and analog ground, typical source isolation impedance of 10 k. 5. Input signals with large slew rates or high frequency noise components cannot be converted accurately. These signals may affect the conversion accuracy of other channels 6. Below disruptive current conditions, the channel being stressed has conversion values of $3FF for analog inputs greater than VRH and $000 for values less than VRL. This assumes that VRH < VDDA and VRL > VSSA due to the presence of the sample amplifier. Other channels are not affected by non-disruptive conditions. 7. Exceeding limit may cause conversion error on stressed channels and on unstressed channels. Transitions within the limit do not affect device reliability or cause permanent damage. 8. Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate resistance values using VPOSCLAMP = VDDA + 0.5 V and VNEGCLAMP = - 0.3 V, then use the larger of the calculated values. 9. Condition applies to two adjacent pins. 10. Current coupling ratio, K, is defined as the ratio of the output current, IOut, measured on the pin under test to the injection current, IINJ, when both adjacent pins are overstressed with the specified injection current. K = IOut/ IINJ The input voltage error on the channel under test is calculated as VERR = IINJ x K x RS. -- Continued -- MMC2107 - Rev. 2.0 MOTOROLA Technical Data Electrical Specifications For More Information On This Product, Go to: www.freescale.com 593 Freescale Semiconductor, Inc. Electrical Specifications Freescale Semiconductor, Inc... 11. Maximum source impedance is application-dependent. Error resulting from pin leakage depends on junction leakage into the pin and on leakage due to charge-sharing with internal capacitance. Error from junction leakage is a function of external source impedance and input leakage current. In the following expression, expected error in result value due to junction leakage is expressed in voltage (VERRJ): VERRJ = RS x IOff where: IOff is a function of operating temperature. Charge-sharing leakage is a function of input source impedance, conversion rate, change in voltage between successive conversions, and the size of the filtering capacitor used. Error levels are best determined empirically. In general, continuous conversion of the same channel may not be compatible with high-source impedance. 12. For a maximum sampling error of the input voltage 1 LSB, then the external filter capacitor, Cf 1024 x CSAMP. The value of C SAMP in the new design may be reduced. 22.10 FLASH Memory Characteristics The FLASH memory characteristics are shown in Table 22-9, Table 22-10, Figure 22-2, and Figure 22-1. Table 22-9. FLASH Program and Erase Characteristics (VDDF = 3.135 to 3.465 V, VPP = 4.75 to 5.25 V, TA = TL to TH) Parameter Symbol Min Typ Max Unit Number of erase pulses EPulse 8 8 20 -- Erase pulse time tErase Erase recovery time tE_Off 4.0 4.8 6.0 s Number of program pulses PPulse -- 500 Note 1 -- Program pulse time tPROG See Table 9-9. Required Programming Algorithm on page 213. Program recovery time tP_Off 4.0 See Table 9-11. Required Erase Algorithm on page 219. 4.8 6.0 s 1. Maximum pulses vary with VPP. Table 22-10. FLASH EEPROM Module Life Characteristics (VDDF = 2.7 to 3.6 V, VPP = 4.75 to 5.25 V, TA = TL to TH) Parameter Symbol Value Unit Maximum number of guaranteed program/ erase cycles(1) P/E 100(2) Cycles Data retention at average operating temperature of 85C Retention 10 Years 1. A program/erase cycle is defined as switching the bits from 1 0 1. 2. Reprogramming of a FLASH array block prior to erase is not required. Technical Data 594 MMC2107 - Rev. 2.0 Electrical Specifications For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Electrical Specifications FLASH Memory Characteristics 700 600 TIME (SECONDS) 500 400 300 Freescale Semiconductor, Inc... 200 100 0 4.75 4.85 4.95 5.05 5.15 5.25 5.35 VPP (V) Notes: 1. Data taken with VDD = 3.6 V at 25C 2. One page at a time programming of full 128-K array 3. Total number of pulses increases with lower VPP. See Figure 22-2. Figure 22-1. VPP versus Programming Time 7000 MINIMUM PULSES 6000 MAXIMUM PULSES PULSES 5000 AVERAGE PULSES/PAGE 4000 3000 Note: This is an example of a fairly worst-case part. Number of pulses required varies from part to part even at the same VPP. 2000 1000 0 4.75 4.95 5.15 5.35 VPP Figure 22-2. VPP versus Programming Pulses MMC2107 - Rev. 2.0 MOTOROLA Technical Data Electrical Specifications For More Information On This Product, Go to: www.freescale.com 595 Freescale Semiconductor, Inc. Electrical Specifications 22.11 External Interface Timing Characteristics Table 22-11. External Interface Timing Characteristics (VDD = 2.7 V to 3.6 V, VSS = 0 V, TA = TL to TH) Characteristic(1), (2) Freescale Semiconductor, Inc... No. Symbol Min Max Unit 1 CLKOUT period tcyc 30 -- ns 2 CLKOUT low pulse width tCLW 0.5 tcyc - 1 -- ns 3 CLKOUT high pulse width tCHW 0.5 tcyc - 1 -- ns 4 All rise times tCR -- 3 ns 5 All fall times tCF -- 3 ns 6 CLKOUT high to A[22:0], TSIZ[1:0] valid(3) tCHAV -- 10 ns 7 CLKOUT high to A[22:0], TSIZ[1:0] invalid tCHAI 0 -- ns 8 CLKOUT high to CS[3:0] asserted tCHCA -- 10 ns 9 CLKOUT high to CS[3:0] negated tCHCN 0 -- ns 10 CLKOUT high to CSE[1:0] valid tCHCEV -- 10 ns 11 CLKOUT high to CSE[1:0] invalid tCHCEI 0 -- ns 12 CLKOUT high to TC[2:0], PSTAT[3:0] valid tCHTV -- 15 ns 13 CLKOUT high to TC[2:0], PSTAT[3:0] invalid tCHTI 0 -- ns 14 CLKOUT high to R/W high hold time tCHRWH 0 10 ns 15 CLKOUT high to R/W valid write tCHRWV 0.25 tcyc 0.25 tcyc + 9 ns 16 CLKOUT high to OE, EB asserted(4), (5) tCHOEA 0.25 tcyc 0.25 tcyc + 9 ns 17 CLKOUT high to OE, EB read negated tCHOEN 0 9 ns CLKOUT low to EB write negated tCLEN 0.25 tcyc 0.25 tcyc + 10 ns 18 CLKOUT low to SHS low tCLSL 0 10 ns 19 CLKOUT High to SHS high(6) tCHSH 0 8 ns 20 CLKOUT low to data-out low impedance write/show tCHDOD 0 -- ns 21 CLKOUT high to data-out high impedance write/show(7) tCHDOZ 2 10 ns 22 CLKOUT low to data-out valid write tCLDOVW -- 12 ns 22A CLKOUT low to data-out valid show tCLDOVS -- 12 ns CLKOUT high to data-out invalid write/show tCHDOIW 10 -- ns 17A 23 Technical Data 596 MMC2107 - Rev. 2.0 Electrical Specifications For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Electrical Specifications External Interface Timing Characteristics Table 22-11. External Interface Timing Characteristics (Continued) (VDD = 2.7 V to 3.6 V, VSS = 0 V, TA = TL to TH) Characteristic(1), (2) Freescale Semiconductor, Inc... No. Symbol Min Max Unit 24 Data-in valid to CLKOUT high read tDIVCH 22 -- ns 25 CLKOUT high to data-in invalid read tCHDII 0 -- ns 26 TA, TEA asserted to CLKOUT high tTACH 0.25 tcyc + 14 -- ns 27 CLKOUT high to TA, TEA negated tCHTN 0 -- ns 1. All AC timing is shown with respect to 20% V DD and 80% VDD levels, unless otherwise noted. 2. Timing is not guaranteed during the clock cycle of mode and/or setup changes (for example, changing pin function between GPIO and primary function, changing GPIO between input/output functions, changing control registers that affect pin functions). 3. A[22:0], TSIZ[1:0], CS[3:0] valid to R/W (write), OE, EB asserted (minimum) spec is 0 ns. This parameter is characterized before qualification rather than 100% tested. 4. Write/show data high-Z to OE asserted (minimum) or from EB negated (write -- maximum) spec is 0 ns. This parameter is characterized before qualification rather than 100% tested. 5. To prevent an unintentional assertion glitch of the EB pins during a synchronous reset (and before the reset overrides configure the chip in a stable mode), leave the port output data register bits associated with the EB GPO default of 1 and do not pull the pins down with a current load. 6. SHS high to show data or write data invalid (minimum) spec is 0 ns. This parameter is characterized before qualification rather than 100% tested. 7. Write/show data high-Z and write/show data invalid is 0 ns for synchronous reset conditions. 1 4 5 CLKOUT 2 3 Figure 22-3. CLKOUT Timing MMC2107 - Rev. 2.0 MOTOROLA Technical Data Electrical Specifications For More Information On This Product, Go to: www.freescale.com 597 Freescale Semiconductor, Inc. Electrical Specifications CLKOUT 7 6 A[22:0] TSIZ[1:0] 9 8 CS3-CS0 10 11 CSE[1:0] Freescale Semiconductor, Inc... 12 13 TC[2:0], PSTAT[3:0] 14 R/W (READ) 15 R/W (WRITE) 17 16 OE 17A EB[3:0] (WRITE) EB[3:0] (READ) SHS 18 19 22 23 D[31:0] (WRITE) 20 21 24 25 D[31:0] (READ) 26 27 TA/TEA Figure 22-4. Clock Read/Write Cycle Timing Technical Data 598 MMC2107 - Rev. 2.0 Electrical Specifications For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Electrical Specifications External Interface Timing Characteristics CLKOUT 7 6 A[22:0] TSIZ[1:0] 8 9 CS3-CS0 10 11 CSE[1:0] Freescale Semiconductor, Inc... 12 13 TC[2:0], PSTAT[3:0] 14 R/W (READ) 15 R/W (WRITE) 17 16 OE 17A EB[3:0] (WRITE) EB[3:0] (READ) SHS 18 19 22 23 D[31:0] (WRITE) 20 21 24 25 D[31:0] (READ) 27 26 TA/TEA Figure 22-5. Read/Write Cycle Timing with Wait States MMC2107 - Rev. 2.0 MOTOROLA Technical Data Electrical Specifications For More Information On This Product, Go to: www.freescale.com 599 Freescale Semiconductor, Inc. Electrical Specifications CLKOUT 7 6 A[22:0] TSIZ[1:0] CS3-CS0 10 11 CSE[1:0] Freescale Semiconductor, Inc... 12 13 TC[2:0], PSTAT[3:0] 14 R/W (READ) 15 R/W (WRITE) OE EB[3:0] 18 19 SHS 22A 23 D[31:0] (WRITE) 20 21 TA/TEA Figure 22-6. Show Cycle Timing Technical Data 600 MMC2107 - Rev. 2.0 Electrical Specifications For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Electrical Specifications Reset and Configuration Override Timing 22.12 Reset and Configuration Override Timing Table 22-12. Reset and Configuration Override Timing (VDD = 2.7 to 3.6 V, VSS = 0 V, TA = TL to TH) Parameter(1) Freescale Semiconductor, Inc... No. Symbol Min Max Unit R1 RESET input asserted to CLKOUT high tRACH 10 -- ns R2 CLKOUT high to RESET input negated tCHRN 2 -- ns R3 RESET input assertion time(2) tRIAT 5 -- tcyc R4 CLKOUT high to RSTOUT valid(3) tCHROV -- 20 ns R5 RSTOUT asserted to config. overrides asserted tROACA 0 -- ns R6 Configuration override setup time to RSTOUT negated tCOS 20 -- tcyc R7 Configuration override hold time after RSTOUT negated tCOH 0 -- ns R8 RSTOUT negated to configuration override high impedance tRONCZ -- 1 tcyc 1. All AC timing is shown with respect to 20% V DD and 80% VDD levels, unless otherwise noted. 2. During low-power STOP, the synchronizers for the RESET input are bypassed and RESET is asserted asynchronously to the system. Thus, RESET must be held a minimum of 100 ns. 3. This parameter also covers the timing of the show interrupt function. CLKOUT R2 R1 RESET R3 R4 R4 RSTOUT R8 R5 R6 R7 CONFIGURATION OVERRIDES (RCON, D[28, 26, 23:21, 19:16]) Figure 22-7. RESET and Configuration Override Timing MMC2107 - Rev. 2.0 MOTOROLA Technical Data Electrical Specifications For More Information On This Product, Go to: www.freescale.com 601 Freescale Semiconductor, Inc. Electrical Specifications 22.13 SPI Timing Characteristics Table 22-13. SPI Timing Characteristics (VDD = 2.7 to 3.6 V, VSS = 0 V, TA = TL to TH) Freescale Semiconductor, Inc... No. Function Symbol Min Max Unit fop DC DC 1/2 x fsys 1/2 x fsys System frequency 1 Operating frequency Master Slave 2 SCK period Master Slave tSCK 2 2 2048 -- tcyc tcyc 3 Enable lead time Master Slave tLead 1/2 1 -- -- tsck tcyc 4 Enable lag time Master Slave tLag 1/2 1 -- -- tsck tcyc 5 Clock (SCK) high or low time Master Slave tWSCK tcyc - 30 tcyc - 30 1024 tcyc -- ns 6 Data setup time, inputs Master Slave tSU 25 25 -- -- ns 7 Data hold time, inputs Master Slave tHigh 0 25 -- -- ns 8 Slave access time tA -- 1 tcyc 9 Slave MISO disable time tDIS -- 1 tcyc 10 Data valid after SCK edge Master Slave tV -- -- 25 25 ns 11 Data hold time, outputs Master Slave tHold 0 0 -- -- ns 12 Rise time Input Output tRI tRO -- -- tcyc - 25 25 ns 13 Fall time Input Output tFI tFO -- -- tcyc - 25 25 ns Technical Data 602 MMC2107 - Rev. 2.0 Electrical Specifications For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Electrical Specifications SPI Timing Characteristics SS1 OUTPUT 2 1 SCK CPOL = 0 OUTPUT 11 4 12 SCK CPOL = 1 OUTPUT 5 Freescale Semiconductor, Inc... 3 4 6 MISO INPUT MSB IN2 BIT 6 . . . 1 9 LSB IN 9 MOSI OUTPUT 10 BIT 6 . . . 1 MSB OUT2 LSB OUT Notes: 1. SS output mode (DDS7 = 1, SSOE = 1) 2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB. A) SPI Master Timing (CPHA = 0) SS1 OUTPUT 1 2 12 11 11 12 3 SCK CPOL = 0 OUTPUT 4 4 SCK CPOL = 1 OUTPUT 5 MISO INPUT 6 MSB IN2 BIT 6 . . . 1 10 9 MOSI OUTPUT PORT DATA LSB IN MASTER MSB OUT2 BIT 6 . . . 1 MASTER LSB OUT PORT DATA Notes: 1. SS output mode (DDS7 = 1, SSOE = 1) 2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB. B) SPI Master Timing (CPHA = 1) Figure 22-8. SPI Timing Diagram (Sheet 1 of 2) MMC2107 - Rev. 2.0 MOTOROLA Technical Data Electrical Specifications For More Information On This Product, Go to: www.freescale.com 603 Freescale Semiconductor, Inc. Electrical Specifications SS INPUT 1 12 11 11 12 3 SCK CPOL = 0 INPUT 4 2 4 SCK CPOL = 1 INPUT 8 7 Freescale Semiconductor, Inc... MISO OUTPUT 9 BIT 6 . . . 1 MSB OUT SLAVE 5 10 10 SLAVE LSB OUT SEE NOTE 6 MOSI INPUT BIT 6 . . . 1 MSB IN LSB IN Note: Not defined, but normally MSB of character just received A) SPI Slave Timing (CPHA = 0) SS INPUT 3 1 2 12 11 11 12 SCK CPOL = 0 INPUT 4 4 SCK CPOL = 1 INPUT SEE NOTE 7 MOSI INPUT 8 10 9 MISO OUTPUT SLAVE MSB OUT 5 BIT 6 . . . 1 SLAVE LSB OUT 6 MSB IN BIT 6 . . . 1 LSB IN Note: Not defined, but normally LSB of character just received B) SPI Slave Timing (CPHA = 1) Figure 24-7. SPI Timing Diagram (Sheet 2 of 2) Technical Data 604 MMC2107 - Rev. 2.0 Electrical Specifications For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Electrical Specifications OnCE, JTAG, and Boundary Scan Timing 22.14 OnCE, JTAG, and Boundary Scan Timing Table 22-14. OnCE, JTAG, and Boundary Scan Timing (VDD = 2.7 to 3.6 V, VSS = 0 V, TA = TL to TH) Freescale Semiconductor, Inc... No. Characteristics Symbol Min Max Unit 1 TCLK frequency of operation fJCYC dc 1/2 x fsys MHz 2 TCLK cycle period tJCYC 2 -- tcyc 3 TCLK clock pulse width tJCW 25 -- ns 4 TCLK rise and fall times tJCRF 0 3 ns 5 Boundary scan input data setup time to TCLK rise tBSDST 5 -- ns 6 Boundary scan input data hold time after TCLK rise tBSDHT 24 -- ns 7 TCLK low-to-boundary scan output data valid tBSDV 0 40 ns 8 TCLK low-to-boundary scan output high Z tBSDZ 0 40 ns 9 TMS, TDI, and DE input data setup time to TCLK rise(1) tTAPDST 7 -- ns 10 TMS, TDI, and DE input data hold time after TCLK rise(1) tTAPDHT 15 -- ns 11 TCLK low to TDO data valid tTDODV 0 25 ns 12 TCLK low to TDO high Z tTDODZ 0 9 ns 13 TRST assert time tTRSTAT 100 -- ns 14 TRST setup time (negation) to TCLK high tTRSTST 10 -- ns 15 DE input data setup time to CLKOUT rise(1) tDEDST 10 -- ns 16 DE input data hold time after CLKOUT rise(1) tDEDHT 2 -- ns 17 CLKOUT high to DE data valid tDEDV 0 20 ns 18 CLKOUT high to DE high Z tDEDZ 0 10 ns 1. Parameters 9 and 10 apply to the DE pin when used to enable OnCE. Parameters 15 and 16 apply to the DE pin when used to request the processor to enter debug mode. 2 3 3 VIH TCLK INPUT VIL 4 4 Figure 22-9. Test Clock Input Timing MMC2107 - Rev. 2.0 MOTOROLA Technical Data Electrical Specifications For More Information On This Product, Go to: www.freescale.com 605 Freescale Semiconductor, Inc. Electrical Specifications TCLK VIH VIL 5 6 INPUT DATA VALID DATA INPUTS 7 OUTPUT DATA VALID DATA OUTPUTS 8 DATA OUTPUTS Freescale Semiconductor, Inc... 7 OUTPUT DATA VALID DATA OUTPUTS Figure 22-10. Boundary Scan (JTAG) Timing TCLK VIL VIH 9 TDI TMS DE 10 INPUT DATA VALID 11 OUTPUT DATA VALID TDO 12 TDO 11 OUTPUT DATA VALID TDO Figure 22-11. Test Access Port Timing TCLK 14 TRST 13 Figure 22-12. TRST Timing Technical Data 606 MMC2107 - Rev. 2.0 Electrical Specifications For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Electrical Specifications OnCE, JTAG, and Boundary Scan Timing CLKOUT VIL VIH 15 16 INPUT DATA VALID DE INPUT 17 OUTPUT DATA VALID DE 18 DE Freescale Semiconductor, Inc... 17 DE OUTPUT DATA VALID Figure 22-13. Debug Event Pin Timing MMC2107 - Rev. 2.0 MOTOROLA Technical Data Electrical Specifications For More Information On This Product, Go to: www.freescale.com 607 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Electrical Specifications Technical Data 608 MMC2107 - Rev. 2.0 Electrical Specifications For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 23. Mechanical Specifications Freescale Semiconductor, Inc... 23.1 Contents 23.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 609 23.3 Bond Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 610 23.4 Package Information for the 144-Pin LQFP . . . . . . . . . . . . . . 611 23.5 Package Information for the 100-Pin LQFP . . . . . . . . . . . . . . 611 23.6 144-Pin LQFP Mechanical Drawing . . . . . . . . . . . . . . . . . . . . 612 23.7 100-Pin LQFP Mechanical Drawing . . . . . . . . . . . . . . . . . . . . 613 23.2 Introduction The MMC2107 is available in two types of packages: 1. 100-pin low-profile quad flat pack (LQFP) version supporting single-chip mode of operation 2. 144-pin LQFP version supporting: - Single-chip operation with extra general-purpose input/output - Expanded master mode for interfacing to external memories - Emulation mode for development and debug This section shows the latest package specifications available at the time of this publication. To make sure that you have the latest information, contact one of the following: * Local Motorola Sales Office * World Wide Web at http://www.mcu.motsps.com Follow the World Wide Web on-line instructions to retrieve the current mechanical specifications. MMC2107 - Rev. 2.0 MOTOROLA Technical Data Mechanical Specifications For More Information On This Product, Go to: www.freescale.com 609 Freescale Semiconductor, Inc. Mechanical Specifications 23.3 Bond Pins The MMC2107 die has a total of 144 bond pads. Of these, the pads that are not bonded out in the 100-pin package are distributed around the circumference of the die. This optional group of pins includes: A[22:0] R/W EB[3:0] Freescale Semiconductor, Inc... CSE[1:0] TC[2:0] OE CS[3:0] 3 x VDD 3 x VSS For more detailed information, see Section 4. Signal Description. Technical Data 610 MMC2107 - Rev. 2.0 Mechanical Specifications For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Mechanical Specifications Package Information for the 144-Pin LQFP 23.4 Package Information for the 144-Pin LQFP Freescale Semiconductor, Inc... The production 144-pin package characteristics are: * Joint-Electron Device Engineering Council (JEDEC) standard * Low-profile quad flat pack (LQFP) * Dimension: 20 x 20 mm * Lead pitch: 0.5 mm * Thin: 1.4 mm * Case number: 918-03 * Clam shell socket: Yamaichi part #IC51-1444-1354 * Open face socket: Yamaichi part #IC201-1444-034 23.5 Package Information for the 100-Pin LQFP The production 100-pin package characteristics are: * JEDEC standard * Low-profile quad flat pack (LQFP) * Dimension: 14 x 14 mm * Lead pitch: 0.5 mm * Thin: 1.4 mm * Case number: 983-02 * Clam shell socket: Yamaichi part #IC51-1004-809 * Open face socket: Yamaichi part #IC201-1004-008 MMC2107 - Rev. 2.0 MOTOROLA Technical Data Mechanical Specifications For More Information On This Product, Go to: www.freescale.com 611 Freescale Semiconductor, Inc. Mechanical Specifications 23.6 144-Pin LQFP Mechanical Drawing 0.20 T L-M N 4X PIN 1 IDENT 4X 36 TIPS 144 0.20 T L-M N 109 1 108 4X J1 P J1 Freescale Semiconductor, Inc... L M CL B V X X=L, M OR N 140X B1 VIEW Y 36 VIEW Y V1 NOTES: 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS IN MILLIMETERS. 3. DATUMS L, M, N TO BE DETERMINED AT THE SEATING PLANE, DATUM T. 4. DIMENSIONS S AND V TO BE DETERMINED AT SEATING PLANE, DATUM T. 5. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS 0.25 PER SIDE. DIMENSIONS A AND B DO INCLUDE MOLD MISMATCH AND ARE DETERMINED AT DATUM PLANE H. 6. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL NOT CAUSE THE D DIMENSION TO EXCEED 0.35. 73 37 72 N A1 S1 A S VIEW AB C 0.1 T 2 144X SEATING PLANE 2 T PLATING J F C2 AA 0.05 R2 R1 D 0.25 BASE METAL GAGE PLANE 0.08 M T L-M N SECTION J1-J1 (ROTATED 90 ) 144 PL (K) C1 E (Y) VIEW AB 1 DIM A A1 B B1 C C1 C2 D E F G J K P R1 R2 S S1 V V1 Y Z AA 1 2 MILLIMETERS MIN MAX 20.00 BSC 10.00 BSC 20.00 BSC 10.00 BSC 1.40 1.60 0.05 0.15 1.35 1.45 0.17 0.27 0.45 0.75 0.17 0.23 0.50 BSC 0.09 0.20 0.50 REF 0.25 BSC 0.13 0.20 0.13 0.20 22.00 BSC 11.00 BSC 22.00 BSC 11.00 BSC 0.25 REF 1.00 REF 0.09 0.16 0 0 7 11 13 (Z) Technical Data 612 G MMC2107 - Rev. 2.0 Mechanical Specifications For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Mechanical Specifications 100-Pin LQFP Mechanical Drawing 23.7 100-Pin LQFP Mechanical Drawing 4X 0.2 T L-M N G 0.2 T L-M N 4X 25 TIPS 76 100 1 C L X X = L, M OR N AB 75 AB L VIEW Y M Freescale Semiconductor, Inc... BASE METAL B V F J 3X VIEW Y U V1 B1 D PLATING 25 51 26 SECTION AB-AB 50 N A1 0.08 M T L-M N ROTATED 90 CLOCKWISE S1 A S 4X C 2 100X 0.08 T SEATING PLANE T 4X 3 VIEW AA NOTES: 1. DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. 2. DIMENSIONS IN MILLIMETERS. 3. DATUMS L, M AND N TO BE DETERMINED AT THE SEATING PLANE, DATUM T. 4. DIMENSIONS S AND V TO BE DETERMINED AT SEATING PLANE, DATUM T. 5. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS 0.25 PER SIDE. DIMENSIONS A AND B INCLUDE MOLD MISMATCH. 6. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. DAMBAR PROTRUSION SHALL NOT CAUSE THE LEAD WIDTH TO EXCEED 0.35. MINIMUM SPACE BETWEEN PROTRUSION AND ADJACENT LEAD OR PROTRUSION 0.07. 0.05 (W) 1 2X R R1 0.25 C2 GAGE PLANE (K) E C1 (Z) VIEW AA MMC2107 - Rev. 2.0 MOTOROLA DIM A A1 B B1 C C1 C2 D E F G J K R1 S S1 U V V1 W Z 1 2 3 MILLIMETERS MIN MAX 14.00 BSC 7.00 BSC 14.00 BSC 7.00 BSC --1.70 0.05 0.20 1.30 1.50 0.10 0.30 0.45 0.75 0.15 0.23 0.50 BSC 0.07 0.20 0.50 REF 0.08 0.20 16.00 BSC 8.00 BSC 0.09 0.16 16.00 BSC 8.00 BSC 0.20 REF 1.00 REF 0 7 0 --12 REF 12 REF Technical Data Mechanical Specifications For More Information On This Product, Go to: www.freescale.com 613 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Mechanical Specifications Technical Data 614 MMC2107 - Rev. 2.0 Mechanical Specifications For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Technical Data -- MMC2107 Section 24. Ordering Information Freescale Semiconductor, Inc... 24.1 Contents 24.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 615 24.3 MC Order Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .615 24.2 Introduction This section contains instructions for ordering the MMC2107. 24.3 MC Order Numbers Table 24-1. MC Order Numbers MC Order Number(1) Operating Temperature Range MMC2107PU -40C to +85C MMC2107PV -40 C to +85 C 1. PU = 100-pin 14 x 14 mm low-profile quad flat pack (LQFP) PV = 144-pin 20 x 20 mm LQFP MMC2107 - Rev. 2.0 MOTOROLA Technical Data Ordering Information For More Information On This Product, Go to: www.freescale.com 615 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Ordering Information Technical Data 616 MMC2107 - Rev. 2.0 Ordering Information For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... blank For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. USA/EUROPE/LOCATIONS NOT LISTED: Motorola Literature Distribution P.O. Box 5405 Denver, Colorado 80217 1-303-675-2140 1-800-441-2447 MMC2107 Technical Data How to Reach Us: TECHNICAL INFORMATION CENTER: 1-800-521-6274 JAPAN: Motorola Japan Ltd. SPS, Technical Information Center 3-20-1, Minami-Azabu, Minato-ku Tokyo 106-8573 Japan 81-3-3440-3569 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd. Silicon Harbour Centre 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T., Hong Kong 852-26668334 HOME PAGE: http://www.motorola.com/semiconductors/ MMC2107/D REV 2 Q4/00 REV 1