CAT24C44 256-Bit Serial Nonvolatile CMOS Static RAM FEATURES Single 5V Supply JEDEC Standard Pinouts: -8-pin DIP -8-pin SOIC Infinite E2PROM to RAM Recall CMOS and TTL Compatible I/O 100,000 Program/Erase Cycles (E2PROM) Low CMOS Power Consumption: Auto Recall on Power-up -Active: 3 mA Max. -Standby: 30 A Max. Commercial, Industrial and Automotive Temperature Ranges Power Up/Down Protection 10 Year Data Retention DESCRIPTION The CAT24C44 Serial NVRAM is a 256-bit nonvolatile memory organized as 16 words x 16 bits. The high speed Static RAM array is bit for bit backed up by a nonvolatile E2PROM array which allows for easy transfer of data from RAM array to E2PROM (STORE) and from E2PROM to RAM (RECALL). STORE operations are completed in 10ms max. and RECALL operations typically within 1.5s. The CAT24C44 features unlimited RAM write operations either through external RAM writes or internal recalls from E2PROM. Internal false store protection circuitry prohibits STORE operations when VCC is less than 3.5V (typical) ensuring E2PROM data integrity. PIN CONFIGURATION PIN FUNCTIONS The CAT24C44 is manufactured using Catalyst's advanced CMOS floating gate technology. It is designed to endure 100,000 program/erase cycles (E2PROM) and has a data retention of 10 years. The device is available in JEDEC approved 8-pin plastic DIP and SOIC packages. Pin Name DIP Package (P) CE SK DI DO 1 2 3 4 8 7 6 5 VCC STORE RECALL VSS SOIC Package (S) CE SK DI DO 1 2 3 4 8 7 6 5 VCC STORE RECALL VSS 5157 FHD F01 (c) 1998 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice Function SK Serial Clock DI Serial Input DO Serial Data Output CE Chip Enable RECALL Recall STORE Store VCC +5V VSS Ground Doc. No. 25019-0A 2/98 N-1 1 CAT24C44 BLOCK DIAGRAM E2PROM ARRAY RECALL ROW DECODE STATIC RAM ARRAY 256-BIT STORE STORE CONTROL LOGIC RECALL CE INSTRUCTION REGISTER DI COLUMN DECODE DO SK VCC VSS INSTRUCTION DECODE 4-BIT COUNTER 5157 FHD F09 MODE SELECTION(1)(2) Mode STORE RECALL Software Instruction Write Enable Latch Previous Recall Latch Hardware Recall(3) 1 0 NOP X X Software Recall 1 1 RCL X X Hardware Store(3) 0 1 NOP SET TRUE Software Store 1 1 STO SET TRUE X = Don't Care POWER-UP TIMING(4) Symbol Parameter Min. Max. Units VCCSR VCC Slew Rate 0.5 0.005 V/m tpur Power-Up to Read Operations 200 s tpuw Power-Up to Write or Store Operation 5 ms Note: (1) The store operation has priority over all the other operations. (2) The store operation is inhibited when VCC is below 3.5V. (3) NOP designates that the device is not currently executing an instruction. (4) This parameter is tested initially and after a design or process change that affects the parameter. Doc. No. 25019-0A 2/98 N-1 2 CAT24C44 ABSOLUTE MAXIMUM RATINGS* *COMMENT Temperature Under Bias ................. -55C to +125C Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability. Storage Temperature ....................... -65C to +150C Voltage on Any Pin with Respect to Ground(2) ............. -2.0 to +VCC +2.0V VCC with Respect to Ground ............... -2.0V to +7.0V Package Power Dissipation Capability (Ta = 25C) ................................... 1.0W Lead Soldering Temperature (10 secs) ............ 300C Output Short Circuit Current(3) ........................ 100 mA RELIABILITY CHARACTERISTICS Symbol Parameter Min. Max. Units Reference Test Method 100,000 Cycles/Byte MIL-STD-883, Test Method 1033 10 Years MIL-STD-883, Test Method 1008 MIL-STD-883, Test Method 3015 NEND(1) Endurance TDR(1) Data Retention VZAP(1) ESD Susceptibility 2000 Volts ILTH(1)(4) Latch-Up 100 mA JEDEC Standard 17 D.C. OPERATING CHARACTERISTICS VCC = 5V 10%, unless otherwise specified. Limits Symbol Parameter ICCO Min. Typ. Max. Unit Conditions Current Consumption (Operating) 3 mA Inputs = 5.5V, TA = 0C All Outputs Unloaded ISB Current Consumption (Standby) 30 A CE = VIL ILI Input Current 2 A 0 VIN 5.5V ILO Output Leakage Current 10 A 0 VOUT 5.5V VIH High Level Input Voltage 2 VCC V VIL Low Level Input Voltage 0 0.8 V VOH High Level Output Voltage VOL Low Level Output Voltage 2.4 0.4 V IOH = -2mA V IOL = 4.2mA CAPACITANCE TA = 25C, f = 1.0 MHz, VCC = 5V Symbol CI/O(1) CIN(1) Parameter Max. Unit Conditions Input/Output Capacitance 10 pF VI/O = 0V Input Capacitance 6 pF VIN = 0V Note: (1) This parameter is tested initially and after a design or process change that affects the parameter. (2) The minimum DC input voltage is -0.5V. During transitions, inputs may undershoot to -2.0V for periods of less than 20 ns. Maximum DC voltage on output pins is VCC +0.5V, which may overshoot to VCC +2.0V for periods of less than 20 ns. (3) Output shorted for no more than one second. No more than one output shorted at a time. (4) Latch-up protection is provided for stresses up to 100 mA on address and data pins from -1V to VCC +1V. 3 Doc. No. 25019-0A 2/98 N-1 CAT24C44 A.C. CHARACTERISTICS VCC = 5V 10%, unless otherwise specified. Symbol Parameter Min. Max. Units 1 MHz Conditions FSK SK Frequency DC tSKH SK Positive Pulse Width 400 ns tSKL SK Negative Pulse Width 400 ns CL = 100pF + 1TTL gate tDS Data Setup Time 400 ns VOH = 2.2V, VOL = 0.65V tDH Data Hold Time 80 ns VIH = 2.2V, VIL = 0.65V tPD SK Data Valid Time 375 ns Input rise and fall times = 10ns tZ CE Disable Time 1 s tCES CE Enable Setup Time 800 ns tCEH CE Enable Hold Time 400 ns tCDS CE De-Select Time 800 ns A.C. CHARACTERISTICS, Store Cycle VCC = 5V 10%, unless otherwise specified. Limits Symbol Parameter tST Store Time tSTP Store Pulse Width tSTZ Store Disable Time Min. Max. Units Conditions 10 ms CL = 100pF + 1TTL gate ns VOH = 2.2V, VOL = 0.65V 100 ns VIH = 2.2V, VIL = 0.65V Max. Units Conditions 200 A.C. CHARACTERISTICS, Recall Cycle VCC = 5V 10%, unless otherwise specified. Symbol Parameter Min. tRCC Recall Cycle Time 2.5 s tRCP Recall Pulse Width 500 ns CL = 100pF + 1TTL gate tRCZ Recall Disable Time ns VOH = 2.2V, VOL = 0.65V tORC Recall Enable Time ns VIH = 2.2V, VIL = 0.65V tARC Recall Data Access Time 500 10 1.5 s INSTRUCTION SET Format Instruction Start Bit Address OP Code Operation WRDS 1 XXXX 000 Reset Write Enable Latch (Disables, Writes and Stores) STO 1 XXXX 001 Store RAM Data in E2PROM WRITE 1 AAAA 011 Write Data into RAM Address AAAA WREN 1 XXXX 100 Set Write Enable Latch (Enables, Writes and Stores) RCL 1 XXXX 101 Recall E2PROM Data into RAM READ 1 AAAA 11X Read Data From RAM Address AAAA X = Don't care A = Address bit Doc. No. 25019-0A 2/98 N-1 4 CAT24C44 from the device: If the CE pin is prematurely deselected while shifting in an instruction, that instruction will not be executed, and the shift register internal to the CAT24C44 will be cleared. If there are more than or less than 16 clocks during a memory data transfer, an improper data transfer will result. The SK clock is completely static allowing the user to stop the clock and restart it to resume shifting of data. DEVICE OPERATION The CAT24C44 is intended for use with standard microprocessors. The CAT24C44 is organized as 16 registers by 16 bits. Seven 8-bit instructions control the device's operating modes, the RAM reading and writing, and the E2PROM storing and recalling. It is also possible to control the E2PROM store and recall functions in hardware with the STORE and RECALL pins. The CAT24C44 operates on a single 5V supply and will generate, on chip, the high voltage required during a RAM to E2PROM storing operation. Read Upon receiving a start bit, 4 address bits, and the 3-bit read command (clocked into the DI pin), the DO pin of the CAT24C44 will come out of the high impedance state and the 16 bits of data, located at the address specified in the instructions, will be clocked out of the device. When clocking data from the device, the first bit clocked out (DO) is timed from the falling edge of the 8th clock, all succeeding bits (D1-D15) are timed from the rising edge of the clock. Instructions, addresses and write data are clocked into the DI pin on the rising edge of the clock (SK). The DO pin remains in a high impedance state except when outputting data from the device. The CE (Chip Enable) pin must remain high during the entire data transfer. The format for all instructions sent to the CAT24C44 is a logical `1' start bit, 4 address bits (data read or write operations) or 4 "Don't Care" bits (device mode operations), and a 3-bit op code (see Instruction Set). For data write operations, the 8-bit instruction is followed by 16 bits of data. For data read instructions, DO will come out of the high impedance state and enable 16 bits of data to be clocked from the device. The 8th bit of the read instruction is a "Don't Care" bit. This is to eliminate any bus contention that would occur in applications where the DI and DO pins are tied together to form a common DI/DO line. A word of caution while clocking data to and Write After receiving a start bit, 4 address bits, and the 3-bit WRITE command, the 16-bit word is clocked into the device for storage into the RAM memory location specified. The CE pin must remain high during the entire write operation. Figure 1. RAM Read Cycle Timing CE 1 2 3 4 5 6 7 8 1 A A A A 1 1 X 9 10 11 12 22 23 24 SK (8) (1) DI HIGH-Z DO D0 D1 D2 D3 D14 D15 D0 5157 FHD F02 Figure 2. RAM Write Cycle Timing CE 1 2 3 4 5 6 7 1 A A A A 0 1 8 9 10 11 12 22 23 24 SK DI 1 Note: (1) Bit 8 of READ instruction is "Don't Care". D0 D1 D2 D3 D13 D14 D15 5157 FHD F03 5 Doc. No. 25019-0A 2/98 N-1 CAT24C44 WREN/WRDS (STO). The WRDS (write/store disable) can be used to disable all CAT24C44 programming functions, and will prevent any accidental writing to the RAM, or storing to the E2PROM. The CAT24C44 powers up in the program disable state (the "write enable latch" is reset). Any programming after power-up or after a WRDS (RAM write/E2PROM store disable) instruction must first be preceded by the WREN (RAM write/E2PROM store enable) instruction. Once writing/storing is enabled, it will remain enabled until power to the device is removed, the WRDS instruction is sent, or an E2PROM store has been executed Data can be read normally from the CAT24C44 regardless of the "write enable latch" status. Figure 3. Read Cycle Timing SK CYCLE # 6 7 8 9 10 11 SK V IH CE t PD DI t PD tZ HIGH-Z DO D0 D1 Dn HIGH-Z 5157 FHD F04 Figure 4. Write Cycle Timing 1/F SK t SKH SK x t SKL 1 2 n t CES t CEH t CDS CE t DS t DH DI 5157 FHD F05 Doc. No. 25019-0A 2/98 N-1 6 CAT24C44 RECALL RCL/RECALL inadvertent store operations, the following conditions must each be met before data can be transferred into nonvolatile storage: Data is transferred from the E2PROM data memory to RAM by either sending the RCL instruction or by pulling the RECALL input pin low. A recall operation must be performed before the E2PROM store, or RAM write operations can be executed. Either a hardware or software recall operation will set the "previous recall" latch internal to the CAT24C44. * The "previous recall" latch must be set (either a software or hardware recall operation). * The "write enable" latch must be set (WREN instruction issued). POWER-ON RECALL * STO instruction issued or STORE input low. The CAT24C44 has a power-on recall function that transfers the E2PROM data to the RAM. After Power-up, all functions are inhibited for at least 200ns (Tpur) from stable Vcc. During the store operation, all other CAT24C44 functions are inhibited. Upon completion of the store operation, the "write enable" latch is reset. The device also provides false store protection whenever VCC falls below a 3.5V level. If VCC falls below this level, the store operation is disabled and the "write enable" latch is reset. STORE STO/STORE Data in the RAM memory area is stored in the E2PROM memory either by sending the STO instruction or by pulling the STORE input pin low. As security against any Figure 5. Recall Cycle Timing tRCC tRCP RECALL tRCZ tARC HIGH-Z DO VALID DATA tORC UNDEFINED DATA 5157 FHD F06 Figure 6. Hardware Store Cycle Timing tST tSTP STORE tSTZ HIGH-Z DO 5157 FHD F07 7 Doc. No. 25019-0A 2/98 N-1 CAT24C44 Figure 7. Non-Data Operations CE 1 2 3 4 5 1 X X X X 6 7 8 SK DI OP-CODE 5157 FHD F08 ORDERING INFORMATION Prefix Device # CAT 24C44 Optional Company ID Product Number Suffix S I -TE13 Temperature Range Blank = Commercial (0 - 70C) I = Industrial (-40 - 85C) A = Automotive (-40 - 105C)* Tape & Reel TE13: 2000/Reel Package P: PDIP S: SOIC (JEDEC) 24C44 F11 * -40 to +125C is available upon request Notes: (1) The device used in the above example is a 24C44SI-TE13 (SOIC, Industrial Temperature, Tape & Reel) Doc. No. 25019-0A 2/98 N-1 8