LM4808 LM4808 Dual 105 mW Headphone Amplifier Literature Number: SNAS051C LM4808 Dual 105 mW Headphone Amplifier General Description Key Specifications The LM4808 is a dual audio power amplifier capable of delivering 105mW per channel of continuous average power into a 16 load with 0.1% (THD+N) from a 5V power supply. Boomer audio power amplifiers were designed specifically to provide high quality output power with a minimal amount of external components using surface mount packaging. Since the LM4808 does not require bootstrap capacitors or snubber networks, it is optimally suited for low-power portable systems. The unity-gain stable LM4808 can be configured by external gain-setting resistors. n THD+N at 1kHz at 105mW continuous average output power into 16 0.1% (typ) n THD+N at 1kHz at 70mW continuous average output power into 32 0.1% (typ) n Output power at 0.1% THD+N at 1kHz into 32 70mW (typ) Features n n n n n LLP, MSOP, and SOP surface mount packaging Switch on/off click suppression Excellent power supply ripple rejection Unity-gain stable Minimum external components Applications n Headphone Amplifier n Personal Computers n Portable electronic devices Typical Application 10127601 *Refer to the Application Information Section for information concerning proper selection of the input and output coupling capacitors. FIGURE 1. Typical Audio Amplifier Application Circuit Boomer (R) is a registered trademark of National Semiconductor Corporation. (c) 2001 National Semiconductor Corporation DS101276 www.national.com LM4808 Dual 105 mW Headphone Amplifier August 2001 LM4808 Connection Diagrams LLP Package 10127657 Top View Order Number LM4808LD See NS Package Number LDA08B SOP & MSOP Package 10127602 Top View Order Number LM4808M, LM4808MM See NS Package Number M08A, MUA08A www.national.com 2 (Note 3) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage 6.0V 56C/W JA (MSOP) 210C/W JC (SOP) 35C/W JA (SOP) 170C/W JC (LLP) 15C/W -65C to +150C JA (LLP) 117C/W (Note 9) -0.3V to VDD + 0.3V JA (LLP) 150C/W (Note 10) Storage Temperature Input Voltage JC (MSOP) Power Dissipation (Note 4) Internally limited ESD Susceptibility (Note 5) 3500V ESD Susceptibility (Note 6) 250V Junction Temperature Operating Ratings Temperature Range 150C TMIN TA TMAX Soldering Information (Note 1) -40C T Small Outline Package Vapor Phase (60 seconds) 215C Infrared (15 seconds) 220C A 85C 2.0V VDD 5.5V Supply Voltage Note 1: See AN-450 "Surface Mounting and their Effects on Product Reliability" for other methods of soldering surface mount devices. Thermal Resistance Electrical Characteristics (Notes 2, 3) The following specifications apply for VDD = 5V unless otherwise specified, limits apply to TA = 25C. Symbol Parameter Conditions LM4808 Typ (Note Limit (Note 7) 8) VDD Supply Voltage Units (Limits) 2.0 V (min) 5.5 V (max) 1.2 3.0 mA (max) IDD Supply Current VIN = 0V, IO = 0A Ptot Total Power Dissipation VIN = 0V, IO = 0A 6 16.5 mW (max) VOS Input Offset Voltage VIN = 0V 10 50 mV (max) Ibias Input Bias Current VCM Common Mode Voltage GV Open-Loop Voltage Gain Io Max Output Current RO Output Resistance VO Output Swing PSRR Power Supply Rejection Ratio 10 pA 0 V 4.3 V RL = 5k 67 dB THD+N < 0.1 % 70 mA 0.1 RL = 32, 0.1% THD+N, Min .3 RL = 32, 0.1% THD+N, Max 4.7 Cb = 1.0F, Vripple = 100mVPP, f = 100Hz 89 dB 75 dB RL = 16, VO =3.5VPP (at 0 dB) 0.05 % 66 dB RL = 32, VO =3.5VPP (at 0 dB) 0.05 % 66 dB Crosstalk Channel Separation RL = 32 THD+N Total Harmonic Distortion + Noise f = 1 kHz V SNR Signal-to-Noise Ratio VO = 3.5Vpp (at 0 dB) 105 dB fG Unity Gain Frequency Open Loop, RL = 5k 5.5 MHz Po Output Power THD+N = 0.1%, f = 1 kHz RL = 16 105 RL = 32 70 mW 60 mW THD+N = 10%, f = 1 kHz CI RL = 16 150 mW RL = 32 90 mW 3 pF Input Capacitance 3 www.national.com LM4808 Absolute Maximum Ratings LM4808 Electrical Characteristics (Notes 2, 3) (Continued) The following specifications apply for VDD = 5V unless otherwise specified, limits apply to TA = 25C. Symbol Parameter Conditions LM4808 Typ (Note Limit (Note 7) 8) CL Load Capacitance SR Slew Rate 200 Unity Gain Inverting 3 Units (Limits) pF V/s Electrical Characteristics (Notes 2, 3) The following specifications apply for VDD = 3.3V unless otherwise specified, limits apply to TA = 25C. Symbol Parameter Conditions Conditions Typ (Note Limit (Note 7) 8) IDD Supply Current VIN = 0V, IO = 0A VOS Input Offset Voltage VIN = 0V Po Output Power Units (Limits) 1.0 mA (max) 7 mV (max) RL = 16 40 mW RL = 32 28 mW RL = 16 56 mW RL = 32 38 mW THD+N = 0.1%, f = 1 kHz THD+N = 10%, f = 1 kHz Electrical Characteristics (Notes 2, 3) The following specifications apply for VDD = 2.6V unless otherwise specified, limits apply to TA = 25C. Symbol Parameter Conditions Conditions Typ (Note Limit (Note 7) 8) IDD Supply Current VIN = 0V, IO = 0A VOS Input Offset Voltage VIN = 0V Po Output Power THD+N = 0.1%, f = 1 kHz Units (Limits) 0.9 mA (max) 5 mV (max) RL = 16 20 mW RL = 32 16 mW RL = 16 31 mW RL = 32 22 mW THD+N = 10%, f = 1 kHz Note 2: All voltages are measured with respect to the ground pin, unless otherwise specified. Note 3: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given, however, the typical value is a good indication of device performance. Note 4: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, JA, and the ambient temperature TA. The maximum allowable power dissipation is P DMAX = (TJMAX - TA) / JA. For the LM4808, TJMAX = 150C, and the typical junction-to-ambient thermal resistance, when board mounted, is 210C/W for package MUA08A and 170C/W for package M08A. Note 5: Human body model, 100 pF discharged through a 1.5 k resistor. Note 6: Machine Model, 220 pF-240 pF discharged through all pins. Note 7: Typicals are measured at 25C and represent the parametric norm. Note 8: Tested limits are guaranteed to National's AOQL (Average Outgoing Quality Level). Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis. Note 9: The given JA is for an LM4808 packaged in an LDA08B with the Exposed-DAP soldered to a printed circuit board copper pad with an area equivalent to that of the Exposed-DAP itself. Note 10: The given JA is for an LM4808 packaged in an LDA08B with the Exposed-DAP not soldered to any printed circuit board copper. www.national.com 4 LM4808 External Components Description (Figure 1) Components Functional Description 1. Ri The inverting input resistance, along with Rf, set the closed-loop gain. Ri, along with Ci, form a high pass filter with fc = 1/(2RiCi). 2. Ci The input coupling capacitor blocks DC voltage at the amplifier's input terminals. Ci, along with Ri, create a highpass filter with fC = 1/(2RiCi). Refer to the section, Selecting Proper External Components, for an explanation of determining the value of Ci. 3. Rf The feedback resistance, along with Ri, set closed-loop gain. 4. CS This is the supply bypass capacitor. It provides power supply filtering. Refer to the Application Information section for proper placement and selection of the supply bypass capacitor. 5. CB This is the half-supply bypass pin capacitor. It provides half-supply filtering. Refer to the section, Selecting Proper External Components, for information concerning proper placement and selection of CB. 6. CO This is the output coupling capacitor. It blocks the DC voltage at the amplifier's output and forms a high pass filter with RL at fO = 1/(2RLCO) 7. RB This is the resistor which forms a voltage divider that provides 1/2 VDD to the non-inverting input of the amplifier. Typical Performance Characteristics THD+N vs Frequency THD+N vs Frequency 10127603 10127604 THD+N vs Frequency THD+N vs Frequency 10127605 10127606 5 www.national.com LM4808 Typical Performance Characteristics (Continued) THD+N vs Frequency THD+N vs Frequency 10127607 10127608 THD+N vs Frequency THD+N vs Frequency 10127609 10127610 THD+N vs Frequency THD+N vs Frequency 10127611 www.national.com 10127612 6 LM4808 Typical Performance Characteristics (Continued) THD+N vs Output Power THD+N vs Output Power 10127613 10127614 THD+N vs Output Power THD+N vs Output Power 10127615 10127616 THD+N vs Output Power THD+N vs Output Power 10127617 10127618 7 www.national.com LM4808 Typical Performance Characteristics (Continued) THD+N vs Output Power THD+N vs Output Power 10127619 10127620 Output Power vs Load Resistance THD+N vs Output Power 10127622 10127621 Output Power vs Load Resistance Output Power vs Load Resistance 10127623 www.national.com 10127624 8 LM4808 Typical Performance Characteristics (Continued) Output Power vs Supply Voltage Output Power vs Power Supply 10127625 10127626 Output Power vs Power Supply Clipping Voltage vs Supply Voltage 10127628 10127627 Power Dissipation vs Output Power Power Dissipation vs Output Power 10127629 10127630 9 www.national.com LM4808 Typical Performance Characteristics (Continued) Power Dissipation vs Output Power Channel Separation 10127631 10127632 Channel Separation Noise Floor 10127633 10127634 Open Loop Frequency Response Power Supply Rejection Ratio 10127650 10127635 www.national.com 10 LM4808 Typical Performance Characteristics (Continued) Open Loop Frequency Response Open Loop Frequency Response 10127651 10127638 Supply Current vs Supply Voltage Frequency Response vs Output Capacitor Size 10127644 10127645 Frequency Response vs Output Capacitor Size Frequency Response vs Output Capacitor Size 10127646 10127647 11 www.national.com LM4808 Typical Performance Characteristics (Continued) Typical Application Frequency Response Typical Application Frequency Response 10127648 www.national.com 10127649 12 As with any power amplifier, proper supply bypassing is critical for low noise performance and high power supply rejection. Applications that employ a 5V regulator typically use a 10F in parallel with a 0.1F filter capacitors to stabilize the regulator's output, reduce noise on the supply line, and improve the supply's transient response. However, their presence does not eliminate the need for a local 0.1F supply bypass capacitor, CS, connected between the LM4808's supply pins and ground. Keep the length of leads and traces that connect capacitors between the LM4808's power supply pin and ground as short as possible. Connecting a 1.0F capacitor, CB, between the IN A(+) / IN B(+) node and ground improves the internal bias voltage's stability and improves the amplifier's PSRR. The PSRR improvements increase as the bypass pin capacitor value increases. Too large, however, increases the amplifier's turn-on time. The selection of bypass capacitor values, especially CB, depends on desired PSRR requirements, click and pop performance (as explained in the section, Selecting Proper External Components), system cost, and size constraints. EXPOSED-DAP PACKAGE PCB MOUNTING CONSIDERATION The LM4808's exposed-dap (die attach paddle) package (LD) provides a low thermal resistance between the die and the PCB to which the part is mounted and soldered. This allows rapid heat transfer from the die to the surrounding PCB copper traces, ground plane, and surrounding air. The LD package should have its DAP soldered to a copper pad on the PCB. The DAP's PCB copper pad may be connected to a large plane of continuous unbroken copper. This plane forms a thermal mass, heat sink, and radiation area. However, since the LM4808 is designed for headphone applications, connecting a copper plane to the DAP's PCB copper pad is not required. The LM4808's Power Dissipation vs Output Power Curve in the Typical Performance Characteristics shows that the maximum power dissipated is just 45mW per amplifier with a 5V power supply and a 32 load. Further detailed and specific information concerning PCB layout, fabrication, and mounting an LD (LLP) package is available from National Semiconductor's Package Engineering Group under application note AN1187. SELECTING PROPER EXTERNAL COMPONENTS Optimizing the LM4808's performance requires properly selecting external components. Though the LM4808 operates well when using external components with wide tolerances, best performance is achieved by optimizing component values. The LM4808 is unity-gain stable, giving a designer maximum design flexibility. The gain should be set to no more than a given application requires. This allows the amplifier to achieve minimum THD+N and maximum signal-to-noise ratio. These parameters are compromised as the closed-loop gain increases. However, low gain demands input signals with greater voltage swings to achieve maximum output power. Fortunately, many signal sources such as audio CODECs have outputs of 1VRMS (2.83VP-P). Please refer to the Audio Power Amplifier Design section for more information on selecting the proper gain. POWER DISSIPATION Power dissipation is a major concern when using any power amplifier and must be thoroughly understood to ensure a successful design. Equation 1 states the maximum power dissipation point for a single-ended amplifier operating at a given supply voltage and driving a specified output load. PDMAX = (VDD) 2 / (22RL) (1) Since the LM4808 has two operational amplifiers in one package, the maximum internal power dissipation point is twice that of the number which results from Equation 1. Even with the large internal power dissipation, the LM4808 does not require heat sinking over a large range of ambient temperature. From Equation 1, assuming a 5V power supply and a 32 load, the maximum power dissipation point is 40mW per amplifier. Thus the maximum package dissipation point is 80mW. The maximum power dissipation point obtained must not be greater than the power dissipation that results from Equation 2: PDMAX = (TJMAX - TA) / JA Input and Output Capacitor Value Selection Amplifying the lowest audio frequencies requires high value input and output coupling capacitors (CI and CO in Figure 1). A high value capacitor can be expensive and may compromise space efficiency in portable designs. In many cases, however, the speakers used in portable systems, whether internal or external, have little ability to reproduce signals below 150Hz. Applications using speakers with this limited frequency response reap little improvement by using high value input and output capacitors. Besides affecting system cost and size, Ci has an effect on the LM4808's click and pop performance. The magnitude of the pop is directly proportional to the input capacitor's size. Thus, pops can be minimized by selecting an input capacitor value that is no higher than necessary to meet the desired -3dB frequency. As shown in Figure 1, the input resistor, RI and the input capacitor, CI, produce a -3dB high pass filter cutoff frequency that is found using Equation (3). In addition, the output load RL, and the output capacitor CO, produce a -3db high pass filter cutoff frequency defined by Equation (4). (2) For package MUA08A, JA = 210C/W. TJMAX = 150C for the LM4808. Depending on the ambient temperature, TA, of the system surroundings, Equation 2 can be used to find the maximum internal power dissipation supported by the IC packaging. If the result of Equation 1 is greater than that of Equation 2, then either the supply voltage must be decreased, the load impedance increased or TA reduced. For the typical application of a 5V power supply, with a 32 load, the maximum ambient temperature possible without violating the maximum junction temperature is approximately 133.2C provided that device operation is around the maximum power dissipation point. Power dissipation is a function of output power and thus, if typical operation is not around the maximum power dissipation point, the ambient temperature may be increased accordingly. Refer to the Typical Performance Characteristics curves for power dissipation information for lower output powers. 13 fI-3db =1/2RICI (3) fO-3db =1/2RLCO (4) www.national.com LM4808 POWER SUPPLY BYPASSING Application Information LM4808 Application Information package. Once the power dissipation equations have been addressed, the required gain can be determined from Equation (7). (Continued) Also, careful consideration must be taken in selecting a certain type of capacitor to be used in the system. Different types of capacitors (tantalum, electrolytic, ceramic) have unique performance characteristics and may affect overall system performance. (7) Thus, a minimum gain of 1.497 allows the LM4808 to reach full output swing and maintain low noise and THD+N perfromance. For this example, let AV =1.5. The amplifiers overall gain is set using the input (Ri ) and feedback (Rf ) resistors. With the desired input impedance set at 20k, the feedback resistor is found using Equation (8). Bypass Capacitor Value Besides minimizing the input capacitor size, careful consideration should be paid to the value of the bypass capacitor, CB. Since CB determines how fast the LM4808 settles to quiescent operation, its value is critical when minimizing turn-on pops. The slower the LM4808's outputs ramp to their quiescent DC voltage (nominally 1/2 VDD), the smaller the turn-on pop. Choosing CB equal to 1.0F or larger, will minimize turn-on pops. As discussed above, choosing Ci no larger than necessary for the desired bandwith helps minimize clicks and pops. AV = Rf/Ri (8) The value of Rf is 30k. AUDIO POWER AMPLIFIER DESIGN The last step in this design is setting the amplifier's -3db frequency bandwidth. To achieve the desired 0.25dB pass band magnitude variation limit, the low frequency response must extend to at lease one-fifth the lower bandwidth limit and the high frequency response must extend to at least five times the upper bandwidth limit. The gain variation for both response limits is 0.17dB, well within the 0.25dB desired limit. The results are an Design a Dual 70mW/32 Audio Amplifier Given: Power Output 70mW Load Impedance Input Level 32 1Vrms (max) Input Impedance Bandwidth 20k 100Hz-20kHz 0.50dB The design begins by specifying the minimum supply voltage necessary to obtain the specified output power. One way to find the minimum supply voltage is to use the Output Power vs Supply Voltage curve in the Typical Performance Characteristics section. Another way, using Equation (5), is to calculate the peak output voltage necessary to achieve the desired output power for a given load impedance. To account for the amplifier's dropout voltage, two additional voltages, based on the Dropout Voltage vs Supply Voltage in the Typical Performance Characteristics curves, must be added to the result obtained by Equation (5). For a single-ended application, the result is Equation (6). VDD (2VOPEAK + (VODTOP + VODBOT)) (9) fH = 20kHz*5 = 100kHz (10) and a (5) As stated in the External Components section, both Ri in conjunction with Ci, and Co with RL, create first order highpass filters. Thus to obtain the desired low frequency response of 100Hz within 0.5dB, both poles must be taken into consideration. The combination of two single order filters at the same frequency forms a second order response. This results in a signal which is down 0.34dB at five times away from the single order filter -3dB point. Thus, a frequency of 20Hz is used in the following equations to ensure that the response is better than 0.5dB down at 100Hz. (6) Ci 1 / (2 * 20 k * 20 Hz) = 0.397F; use 0.39F. Co 1 / (2 * 32 * 20 Hz) = 249F; use 330F. The high frequency pole is determined by the product of the desired high frequency pole, fH, and the closed-loop gain, AV. With a closed-loop gain of 1.5 and fH = 100kHz, the resulting GBWP = 150kHz which is much smaller than the LM4808's GBWP of 900kHz. This figure displays that if a designer has a need to design an amplifier with a higher gain, the LM4808 can still be used without running into bandwidth limitations. The Output Power vs Supply Voltage graph for a 32 load indicates a minimum supply voltage of 4.8V. This is easily met by the commonly used 5V supply voltage. The additional voltage creates the benefit of headroom, allowing the LM4808 to produce peak output power in excess of 70mW without clipping or other audible distortion. The choice of supply voltage must also not create a situation that violates maximum power dissipation as explained above in the Power Dissipation section. Remember that the maximum power dissipation point from Equation (1) must be multiplied by two since there are two independent amplifiers inside the www.national.com fL = 100Hz/5 = 20Hz 14 LM4808 Demonstration Board Layout 10127660 Recommended LD PC Board Layout: Top Silkscreen 10127639 Recommended SO PC Board Layout: Top Silkscreen 10127640 10127661 Recommended SOP PC Board Layout: Top Layer Recommended LD PC Board Layout: Top Layer 10127642 10127662 Recommended SOP PC Board Layout: Bottom Layer Recommended LD PC Board Layout: Bottom Layer 15 www.national.com LM4808 Physical Dimensions inches (millimeters) unless otherwise noted Order Number LM4808LD NS Package Number LDA08B Order Number LM4808M NS Package Number M08A www.national.com 16 LM4808 Dual 105 mW Headphone Amplifier Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Order Number LM4808MM NS Package Number MUA08A LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated