DSPIC33FJ256GP710A-I/PF - MICROCHIP TECHNOLOGY

dsPIC33FJXXXGPX06A/X08A/X10A

Data Sheet

High-Performance ,

16-bit Digital Signal Controllers

Information contained in this publication regarding device

applications and the like is provided only for your convenience

and may be superseded by updates. It is your responsibility to

ensure that your application meets with your specifications.

MICROCHIP MAKES NO REPRESENTATIONS OR

WARRANTIES OF ANY KIND WHETHER EXPRESS OR

IMPLIED, WRITTEN OR ORAL, STATUTORY OR

OTHERWISE, RELATED TO THE INFORMATION,

INCLUDING BUT NOT LIMITED TO ITS CONDITION,

QUALITY, PERFORMANCE, MERCHANTABILITY OR

FITNESS FOR PURPOSE. Microchip disclaims all liability

arising from this information and its use. Use of Microchip

devices in life support and/or safety applications is entirely at

the buyer’s risk, and the buyer agrees to defend, indemnify and

hold harmless Microchip from any and all damages, claims,

suits, or expenses resulting from such use. No licenses are

conveyed, implicitly or otherwise, under any Microchip

intellectual property rights.

Trademarks

The Microchip name and logo, the Microchip logo, dsPIC,

KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART,

PIC32 logo, rfPIC and UNI/O are registered trademarks of

Microchip Technology Incorporated in the U.S.A. and other

countries.

FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor,

MXDEV, MXLAB, SEEVAL and The Embedded Control

Solutions Company are registered trademarks of Microchip

Technology Incorporated in the U.S.A.

Analog-for-the-Digital Age, Application Maestro, CodeGuard,

dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,

ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial

Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified

logo, MPLIB, MPLINK, mTouch, Omniscient Code

Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit,

PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance,

TSHARC, UniWinDriver, WiperLock and ZENA are

trademarks of Microchip Technology Incorporated in the

U.S.A. and other countries.

SQTP is a service mark of Microchip Technology Incorporated

in the U.S.A.

All other trademarks mentioned herein are property of their

respective companies.

Printed on recycled paper.

ISBN: 978-1-61341-014-1

Note the following details of the code protection feature on Microchip devices:

• Microchip products meet the specification contained in their particular Microchip Data Sheet.

• Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the

intended manner and under normal conditions.

• There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our

knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data

Sheets. Most likely, the person doing so is engaged in theft of intellectual property.

• Microchip is willing to work with the customer who is concerned about the integrity of their code.

• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not

mean that we are guaranteeing the product as “unbreakable.”

Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our

products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts

allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.

Microchip received ISO/TS-16949:2002 certification for its worldwide

headquarters, design and wafer fabrication facilities in Chandler and

Tempe, Arizona; Gresham, Oregon and design centers in California

and India. The Company’s quality system processes and procedures

are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping

devices, Serial EEPROMs, microperipherals, nonvolatile memory and

analog products. In addition, Microchip’s quality system for the design

and manufacture of development systems is ISO 9001:2000 certified.

dsPIC33FJXXXGPX06A/X08A/X10A

Operating Range:

• Up to 40 MIPS operation (@ 3.0-3.6V):

- Industrial temperature range (-40°C to +85°C)

- Extended temperature range (-40°C to +125°C)

• Up to 20 MIPS operation (@ 3.0-3.6V):

- High temperature range (-40°C to +150°C)

High-Performance DSC CPU:

• Modified Harvard architecture

• C compiler optimized instruction set

• 16-bit wide dat path

• 24-bit wide instructions

• Linear program memory addressing up to 4M

instruction words

• Linear data memory addressing up to 64 Kbytes

• 83 base instructions: mostly 1 word/1 cycle

• Sixteen 16-bit General Purpose Registers

• Two 40-bit accumulators:

- With rounding and saturation options

• Flexible and powerful addressing modes:

- Indirect, Modulo and Bit-Reversed

• Software stack

• 16 x 16 fractional/integer multiply operations

• 32/16 and 16/16 divide operations

• Single-cycle multiply and accumulate:

- Accumulator write back for DSP operations

- Dual data fetch

• Up to ±16-bit shifts for up to 40-bit data

Direct Memory Access (DMA):

• 8-channel hardware DMA:

• 2 Kbytes dual ported DMA buffer area

(DMA RAM) to store data transferred via DMA:

- Allows data transfer between RAM and a

peripheral while CPU is executing code

(no cycle stealing)

• Most peripherals support DMA

Interrupt Controller:

• 5-cycle latency

• Up to 63 available interrupt sources

• Up to five external interrupts

• Seven programmable priority levels

• Five processor exceptions

Digital I/O:

• Up to 85 programmable digital I/O pins

• Wake-up/Interrupt-on-Change on up to 24 pins

• Output pins can drive from 3.0V to 3.6V

• Up to 5.5V output with open drain configuration on

5V tolerant pins with an external pull-up

• 4 mA sink on all I/O pins

On-Chip Flash and SRAM:

• Flash program memory, up to 256 Kbytes

• Data SRAM, up to 30 Kbytes (includes 2 Kbytes

of DMA RAM):

System Management:

• Flexible clock options:

- External, crystal, resonator, internal RC

- Fully integrated PLL

- Extremely low jitter PLL

• Power-up Timer

• Oscillator Start-up Timer/Stabilizer

• Watchdog Timer with its own RC oscillator

• Fail-Safe Clock Monitor

• Reset by multiple sources

Power Management:

• On-chip 2.5V voltage regulator

• Switch between clock sources in real time

• Idle, Sleep and Doze modes with fast wake-up

Timers/Capture/Compare/PWM:

• Timer/Counters, up to nine 16-bit timers:

- Can pair up to make four 32-bit timers

- 1 timer runs as Real-Time Clock with external

32.768 kHz oscillator

- Programmable prescaler

• Input Capture (up to eight channels):

- Capture on up, down or both edges

- 16-bit capture input functions

- 4-deep FIFO on each capture

• Output Compare (up to eight channels):

- Single or Dual 16-Bit Compare mode

- 16-bit Glitchless PWM mode

High-Performance, 16-Bit Digital Signal Controllers

dsPIC33FJXXXGPX06A/X08A/X10A

Communication Modules:

• 3-wire SPI (up to two modules):

- Framing supports I/O interface to simple

codecs

- Supports 8-bit and 16-bit data

- Supports all serial clock formats and

sampling modes

•I

2C™ (up to two modules):

- Full Multi-Master Slave mode support

- 7-bit and 10-bit addressing

- Bus collision detection and arbitration

- Integrated signal conditioning

- Slave address masking

• UART (up to two modules):

- Interrupt on address bit detect

- Interrupt on UART error

- Wake-up on Start bit from Sleep mode

- 4-character TX and RX FIFO buffers

- LIN bus support

-IrDA

® encoding and decoding in hardware

- High-Speed Baud mode

- Hardware Flow Control with CTS and RTS

• Data Converter Interface (DCI) module:

- Codec interface

- Supports I2S and AC’97 protocols

- Up to 16-bit data words, up to 16 words per

frame

- 4-word deep TX and RX buffers

• Enhanced CAN (ECAN™ module) 2.0B active

(up to two modules):

- Up to eight transmit and up to 32 receive buffers

- 16 receive filters and three masks

- Loopback, Listen Only and Listen All

Messages modes for diagnostics and bus

monitoring

- Wake-up on CAN message

- Automatic processing of Remote

Transmission Requests

- FIFO mode using DMA

- DeviceNet™ addressing support

Analog-to-Digital Converters (ADCs):

• Up to two ADC modules in a device

• 10-bit, 1.1 Msps or 12-bit, 500 ksps conversion:

- Two, four or eight simultaneous samples

- Up to 32 input channels with auto-scanning

- Conversion start can be manual or

synchronized with one of four trigger sources

- Conversion possible in Sleep mode

- ±1 LSb max integral nonlinearity

- ±1 LSb max differential nonlinearity

CMOS Flash Technology:

• Low-power, high-speed Flash technology

• Fully static design

• 3.3V (±10%) operating voltage

• Industrial and extended temperature

• Low-power consumption

Packaging:

• 100-pin TQFP (14x14x1 mm and 12x12x1 mm)

• 80-pin TQFP (12x12x1 mm)

• 64-pin TQFP (10x10x1 mm)

• 64-pin QFN (9x9x0.9 mm)

Note: See the device variant tables for exact

peripheral features per device.

dsPIC33FJXXXGPX06A/X08A/X10A

dsPIC33F PRODUCT FAMILIES

The dsPIC33F General Purpose Family of devices

are ideal for a wide variety of 16-bit MCU embedded

applications. The controllers with codec interfaces are

well-suited for speech and audio processing

applications.

The device names, pin counts, memory sizes and

peripheral availability of each family are listed below,

followed by their pinout diagrams.

dsPIC33F General Purpose Family Controllers

Device Pins

Program

Flash

Memory

(Kbyte)

RAM

(Kbyte)(1)

16-bit Timer

Input Capture

Output Compare

Std. PWM

Codec

Interface

ADC

UART

SPI

I2C™

Enhanced

CAN™

I/O Pins (Max)(2)

Packages

dsPIC33FJ64GP206A 64 64 8 9 8 8 1 1 ADC, 18

221 053PT, MR

dsPIC33FJ64GP306A 64 64 16 9 8 8 1 1 ADC, 18

222 053PT, MR

dsPIC33FJ64GP310A 100 64 16 9 8 8 1 1 ADC, 32

222 085PF, PT

dsPIC33FJ64GP706A 64 64 16 9 8 8 1 2 ADC, 18

222 253PT, MR

dsPIC33FJ64GP708A 80 64 16 9 8 8 1 2 ADC, 24

222 269 PT

dsPIC33FJ64GP710A 100 64 16 9 8 8 1 2 ADC, 32

222 285PF, PT

dsPIC33FJ128GP206A 64 128 8 9 8 8 1 1 ADC, 18

221 053PT, MR

dsPIC33FJ128GP306A 64 128 16 9 8 8 1 1 ADC, 18

222 053PT, MR

dsPIC33FJ128GP310A 100 128 16 9 8 8 1 1 ADC, 32

222 085PF, PT

dsPIC33FJ128GP706A 64 128 16 9 8 8 1 2 ADC, 18

222 253PT, MR

dsPIC33FJ128GP708A 80 128 16 9 8 8 1 2 ADC, 24

222 269 PT

dsPIC33FJ128GP710A 100 128 16 9 8 8 1 2 ADC, 32

222 285PF, PT

dsPIC33FJ256GP506A 64 256 16 9 8 8 1 1 ADC, 18

222 153PT, MR

dsPIC33FJ256GP510A 100 256 16 9 8 8 1 1 ADC, 32

222 185PF, PT

dsPIC33FJ256GP710A 100 256 30 9 8 8 1 2 ADC, 32

222 285PF, PT

Note 1: RAM size is inclusive of 2 Kbytes DMA RAM.

2: Maximum I/O pin count includes pins shared by the peripheral functions.

dsPIC33FJXXXGPX06A/X08A/X10A

Pin Diagrams

64-Pin QFN(1)

PGEC2/SOSCO/T1CK/CN0/RC14

PGED2/SOSCI/T4CK/CN1/RC13

OC1/RD0

IC4/INT4/RD11

IC2/U1CTS/INT2/RD9

IC1/INT1/RD8

VSS

OSC2/CLKO/RC15

OSC1/CLKIN/RC12

VDD

SCL1/RG2

U1RTS/SCK1/INT0/RF6

U1RX/SDI1/RF2

U1TX/SDO1/RF3

COFS/RG15

AN16/T2CK/T7CK/RC1

AN17/T3CK/T6CK/RC2

SCK2/CN8/RG6

SDI2/CN9/RG7

SDO2/CN10/RG8

MCLR

VSS

VDD

AN3/CN5/RB3

AN2/SS1/CN4/RB2

PGEC3/AN1/VREF-/CN3/RB1

PGED3/AN0/VREF+/CN2/RB0

OC8/CN16/RD7

CSDO/RG13

CSDI/RG12

CSCK/RG14

VCAP

RG1

RF1

RG0

OC2/RD1

OC3/RD2

PGEC1/AN6/OCFA/RB6

PGED1/AN7/RB7

AVDD

AVSS

U2CTS/AN8/RB8

AN9/RB9

TMS/AN10/RB10

TDO/AN11/RB11

VSS

VDD

TCK/AN12/RB12

TDI/AN13/RB13

U2RTS/AN14/RB14

AN15/OCFB/CN12/RB15

U2TX/CN18/RF5

U2RX/CN17/RF4

SDA1/RG3

SS2/CN11/RG9

AN5/IC8/CN7/RB5

AN4/IC7/CN6/RB4

IC3/INT3/RD10

VDD

RF0

OC4/RD3

OC7/CN15/RD6

OC6/IC6/CN14/RD5

OC5/IC5/CN13/RD4

dsPIC33FJ64GP206A

dsPIC33FJ128GP206A

= Pins are up to 5V tolerant

64 63 62 61 60 59 58 57 56 55

22 23 24 25 26 27 28 29 30 31

17 18 19 20 21

53 52 51 50 49

Note 1: The metal plane at the bottom of the device is not connected to any pins and should be connected

to VSS externally.

dsPIC33FJXXXGPX06A/X08A/X10A

Pin Diagrams (Continued)

64-Pin QFN(1)

PGEC2/SOSCO/T1CK/CN0/RC14

PGED2/SOSCI/T4CK/CN1/RC13

OC1/RD0

IC4/INT4/RD11

IC2/U1CTS/INT2/RD9

IC1/INT1/RD8

VSS

OSC2/CLKO/RC15

OSC1/CLKIN/RC12

VDD

SCL1/RG2

U1RTS/SCK1/INT0/RF6

U1RX/SDI1/RF2

U1TX/SDO1/RF3

COFS/RG15

AN16/T2CK/T7CK/RC1

AN17/T3CK/T6CK/RC2

SCK2/CN8/RG6

SDI2/CN9/RG7

SDO2/CN10/RG8

MCLR

VSS

VDD

AN3/CN5/RB3

AN2/SS1/CN4/RB2

PGEC3/AN1/VREF-/CN3/RB1

PGED3/AN0/VREF+/CN2/RB0

OC8/CN16/RD7

CSDO/RG13

CSDI/RG12

CSCK/RG14

VCAP

RG1

RF1

RG0

OC2/RD1

OC3/RD2

PGEC1/AN6/OCFA/RB6

PGED1/AN7/RB7

AVDD

AVSS

U2CTS/AN8/RB8

AN9/RB9

TMS/AN10/RB10

TDO/AN11/RB11

VSS

VDD

TCK/AN12/RB12

TDI/AN13/RB13

U2RTS/AN14/RB14

AN15/OCFB/CN12/RB15

U2TX/SCL2/CN18/RF5

U2RX/SDA2/CN17/RF4

SDA1/RG3

SS2/CN11/RG9

AN5/IC8/CN7/RB5

AN4/IC7/CN6/RB4

IC3/INT3/RD10

VDD

RF0

OC4/RD3

OC7/CN15/RD6

OC6/IC6/CN14/RD5

OC5/IC5/CN13/RD4

dsPIC33FJ64GP306A

dsPIC33FJ128GP306A

= Pins are up to 5V tolerant

64 63 62 61 60 59 58 57 56 55

22 23 24 25 26 27 28 29 30 31

17 18 19 20 21

53 52 51 50 49

Note 1: The metal plane at the bottom of the device is not connected to any pins and should be connected

to VSS externally.

dsPIC33FJXXXGPX06A/X08A/X10A

Pin Diagrams (Continued)

64-Pin QFN(1)

PGEC2/SOSCO/T1CK/CN0/RC14

PGED2/SOSCI/T4CK/CN1/RC13

OC1/RD0

IC4/INT4/RD11

IC2/U1CTS/INT2/RD9

IC1/INT1/RD8

VSS

OSC2/CLKO/RC15

OSC1/CLKIN/RC12

VDD

SCL1/RG2

U1RTS/SCK1/INT0/RF6

U1RX/SDI1/RF2

U1TX/SDO1/RF3

COFS/RG15

AN16/T2CK/T7CK/RC1

AN17/T3CK/T6CK/RC2

SCK2/CN8/RG6

SDI2/CN9/RG7

SDO2/CN10/RG8

MCLR

VSS

VDD

AN3/CN5/RB3

AN2/SS1/CN4/RB2

PGEC3/AN1/VREF-/CN3/RB1

PGED3/AN0/VREF+/CN2/RB0

OC8/CN16/RD7

CSDO/RG13

CSDI/RG12

CSCK/RG14

VCAP

RG1

C1TX/RF1

RG0

OC2/RD1

OC3/RD2

PGEC1/AN6/OCFA/RB6

PGED1/AN7/RB7

AVDD

AVSS

U2CTS/AN8/RB8

AN9/RB9

TMS/AN10/RB10

TDO/AN11/RB11

VSS

VDD

TCK/AN12/RB12

TDI/AN13/RB13

U2RTS/AN14/RB14

AN15/OCFB/CN12/RB15

U2TX/SCL2/CN18/RF5

U2RX/SDA2/CN17/RF4

SDA1/RG3

SS2/CN11/RG9

AN5/IC8/CN7/RB5

AN4/IC7/CN6/RB4

IC3/INT3/RD10

VDD

C1RX/RF0

OC4/RD3

OC7/CN15/RD6

OC6/IC6/CN14/RD5

OC5/IC5/CN13/RD4

= Pins are up to 5V tolerant

64 63 62 61 60 59 58 57 56 55

22 23 24 25 26 27 28 29 30 31

17 18 19 20 21

53 52 51 50 49

dsPIC33FJ256GP506A

Note 1: The metal plane at the bottom of the device is not connected to any pins and should be connected

to VSS externally.

dsPIC33FJXXXGPX06A/X08A/X10A

Pin Diagrams (Continued)

64-Pin QFN(1)

PGEC2/SOSCO/T1CK/CN0/RC14

PGED2/SOSCI/T4CK/CN1/RC13

OC1/RD0

IC4/INT4/RD11

IC2/U1CTS/INT2/RD9

IC1/INT1/RD8

VSS

OSC2/CLKO/RC15

OSC1/CLKIN/RC12

VDD

SCL1/RG2

U1RTS/SCK1/INT0/RF6

U1RX/SDI1/RF2

U1TX/SDO1/RF3

COFS/RG15

AN16/T2CK/T7CK/RC1

AN17/T3CK/T6CK/RC2

SCK2/CN8/RG6

SDI2/CN9/RG7

SDO2/CN10/RG8

MCLR

VSS

VDD

AN3/CN5/RB3

AN2/SS1/CN4/RB2

PGEC3/AN1/VREF-/CN3/RB1

PGED3/AN0/VREF+/CN2/RB0

OC8/CN16/RD7

CSDO/RG13

CSDI/RG12

CSCK/RG14

VCAP

C2TX/RG1

C1TX/RF1

C2RX/RG0

OC2/RD1

OC3/RD2

PGEC1/AN6/OCFA/RB6

PGED1/AN7/RB7

AVDD

AVSS

U2CTS/AN8/RB8

AN9/RB9

TMS/AN10/RB10

TDO/AN11/RB11

VSS

VDD

TCK/AN12/RB12

TDI/AN13/RB13

U2RTS/AN14/RB14

AN15/OCFB/CN12/RB15

U2TX/SCL2/CN18/RF5

U2RX/SDA2/CN17/RF4

SDA1/RG3

SS2/CN11/RG9

AN5/IC8/CN7/RB5

AN4/IC7/CN6/RB4

IC3/INT3/RD10

VDD

C1RX/RF0

OC4/RD3

OC7/CN15/RD6

OC6/IC6/CN14/RD5

OC5/IC5/CN13/RD4

dsPIC33FJ64GP706A

dsPIC33FJ128GP706A

= Pins are up to 5V tolerant

64 63 62 61 60 59 58 57 56 55

22 23 24 25 26 27 28 29 30 31

17 18 19 20 21

53 52 51 50 49

Note 1: The metal plane at the bottom of the device is not connected to any pins and should be connected

to VSS externally.

dsPIC33FJXXXGPX06A/X08A/X10A

Pin Diagrams (Continued)

64-Pin TQFP

13 36

PGEC2/SOSCO/T1CK/CN0/RC14

PGED2/SOSCI/T4CK/CN1/RC13

OC1/RD0

IC4/INT4/RD11

IC2/U1CTS/INT2/RD9

IC1/INT1/RD8

VSS

OSC2/CLKO/RC15

OSC1/CLKIN/RC12

VDD

SCL1/RG2

U1RTS/SCK1/INT0/RF6

U1RX/SDI1/RF2

U1TX/SDO1/RF3

COFS/RG15

AN16/T2CK/T7CK/RC1

AN17/T3CK/T6CK/RC2

SCK2/CN8/RG6

SDI2/CN9/RG7

SDO2/CN10/RG8

MCLR

VSS

VDD

AN3/CN5/RB3

AN2/SS1/CN4/RB2

PGEC3/AN1/VREF-/CN3/RB1

PGED3/AN0/VREF+/CN2/RB0

OC8/CN16/RD7

CSDO/RG13

CSDI/RG12

CSCK/RG14

VCAP

RG1

RF1

RG0

OC2/RD1

OC3/RD2

PGEC1/AN6/OCFA/RB6

PGED1/AN7/RB7

AVDD

AVSS

U2CTS/AN8/RB8

AN9/RB9

TMS/AN10/RB10

TDO/AN11/RB11

VSS

VDD

TCK/AN12/RB12

TDI/AN13/RB13

U2RTS/AN14/RB14

AN15/OCFB/CN12/RB15

U2TX/CN18/RF5

U2RX/CN17/RF4

SDA1/RG3

SS2/CN11/RG9

AN5/IC8/CN7/RB5

AN4/IC7/CN6/RB4

IC3/INT3/RD10

VDD

RF0

OC4/RD3

OC7/CN15/RD6

OC6/IC6/CN14/RD5

OC5/IC5/CN13/RD4

dsPIC33FJ64GP206A

dsPIC33FJ128GP206A

= Pins are up to 5V tolerant

dsPIC33FJXXXGPX06A/X08A/X10A

Pin Diagrams (Continued)

64-Pin TQFP

13 36

PGEC2/SOSCO/T1CK/CN0/RC14

PGED2/SOSCI/T4CK/CN1/RC13

OC1/RD0

IC4/INT4/RD11

IC2/U1CTS/INT2/RD9

IC1/INT1/RD8

VSS

OSC2/CLKO/RC15

OSC1/CLKIN/RC12

VDD

SCL1/RG2

U1RTS/SCK1/INT0/RF6

U1RX/SDI1/RF2

U1TX/SDO1/RF3

COFS/RG15

AN16/T2CK/T7CK/RC1

AN17/T3CK/T6CK/RC2

SCK2/CN8/RG6

SDI2/CN9/RG7

SDO2/CN10/RG8

MCLR

VSS

VDD

AN3/CN5/RB3

AN2/SS1/CN4/RB2

PGEC3/AN1/VREF-/CN3/RB1

PGED3/AN0/VREF+/CN2/RB0

OC8/CN16/RD7

CSDO/RG13

CSDI/RG12

CSCK/RG14

VCAP

RG1

RF1

RG0

OC2/RD1

OC3/RD2

PGEC1/AN6/OCFA/RB6

PGED1/AN7/RB7

AVDD

AVSS

U2CTS/AN8/RB8

AN9/RB9

TMS/AN10/RB10

TDO/AN11/RB11

VSS

VDD

TCK/AN12/RB12

TDI/AN13/RB13

U2RTS/AN14/RB14

AN15/OCFB/CN12/RB15

U2TX/SCL2/CN18/RF5

U2RX/SDA2/CN17/RF4

SDA1/RG3

SS2/CN11/RG9

AN5/IC8/CN7/RB5

AN4/IC7/CN6/RB4

IC3/INT3/RD10

VDD

RF0

OC4/RD3

OC7/CN15/RD6

OC6/IC6/CN14/RD5

OC5/IC5/CN13/RD4

dsPIC33FJ64GP306A

dsPIC33FJ128GP306A

= Pins are up to 5V tolerant

dsPIC33FJXXXGPX06A/X08A/X10A

Pin Diagrams (Continued)

64-Pin TQFP

13 36

PGEC2/SOSCO/T1CK/CN0/RC14

PGED2/SOSCI/T4CK/CN1/RC13

OC1/RD0

IC4/INT4/RD11

IC2/U1CTS/INT2/RD9

IC1/INT1/RD8

VSS

OSC2/CLKO/RC15

OSC1/CLKIN/RC12

VDD

SCL1/RG2

U1RTS/SCK1/INT0/RF6

U1RX/SDI1/RF2

U1TX/SDO1/RF3

COFS/RG15

AN16/T2CK/T7CK/RC1

AN17/T3CK/T6CK/RC2

SCK2/CN8/RG6

SDI2/CN9/RG7

SDO2/CN10/RG8

MCLR

VSS

VDD

AN3/CN5/RB3

AN2/SS1/CN4/RB2

PGEC3/AN1/VREF-/CN3/RB1

PGED3/AN0/VREF+/CN2/RB0

OC8/CN16/RD7

CSDO/RG13

CSDI/RG12

CSCK/RG14

VCAP

RG1

C1TX/RF1

RG0

OC2/RD1

OC3/RD2

PGEC1/AN6/OCFA/RB6

PGED1/AN7/RB7

AVDD

AVSS

U2CTS/AN8/RB8

AN9/RB9

TMS/AN10/RB10

TDO/AN11/RB11

VSS

VDD

TCK/AN12/RB12

TDI/AN13/RB13

U2RTS/AN14/RB14

AN15/OCFB/CN12/RB15

U2TX/SCL2/CN18/RF5

U2RX/SDA2/CN17/RF4

SDA1/RG3

SS2/CN11/RG9

AN5/IC8/CN7/RB5

AN4/IC7/CN6/RB4

IC3/INT3/RD10

VDD

C1RX/RF0

OC4/RD3

OC7/CN15/RD6

OC6/IC6/CN14/RD5

OC5/IC5/CN13/RD4

dsPIC33FJ256GP506A

= Pins are up to 5V tolerant

dsPIC33FJXXXGPX06A/X08A/X10A

Pin Diagrams (Continued)

64-Pin TQFP

13 36

PGEC2/SOSCO/T1CK/CN0/RC14

PGED2/SOSCI/T4CK/CN1/RC13

OC1/RD0

IC4/INT4/RD11

IC2/U1CTS/INT2/RD9

IC1/INT1/RD8

VSS

OSC2/CLKO/RC15

OSC1/CLKIN/RC12

VDD

SCL1/RG2

U1RTS/SCK1/INT0/RF6

U1RX/SDI1/RF2

U1TX/SDO1/RF3

COFS/RG15

AN16/T2CK/T7CK/RC1

AN17/T3CK/T6CK/RC2

SCK2/CN8/RG6

SDI2/CN9/RG7

SDO2/CN10/RG8

MCLR

VSS

VDD

AN3/CN5/RB3

AN2/SS1/CN4/RB2

PGEC3/AN1/VREF-/CN3/RB1

PGED3/AN0/VREF+/CN2/RB0

OC8/CN16/RD7

CSDO/RG13

CSDI/RG12

CSCK/RG14

VCAP

C2TX/RG1

C1TX/RF1

C2RX/RG0

OC2/RD1

OC3/RD2

PGEC1/AN6/OCFA/RB6

PGED1/AN7/RB7

AVDD

AVSS

U2CTS/AN8/RB8

AN9/RB9

TMS/AN10/RB10

TDO/AN11/RB11

VSS

VDD

TCK/AN12/RB12

TDI/AN13/RB13

U2RTS/AN14/RB14

AN15/OCFB/CN12/RB15

U2TX/SCL2/CN18/RF5

U2RX/SDA2/CN17/RF4

SDA1/RG3

SS2/CN11/RG9

AN5/IC8/CN7/RB5

AN4/IC7/CN6/RB4

IC3/INT3/RD10

VDD

C1RX/RF0

OC4/RD3

OC7/CN15/RD6

OC6/IC6/CN14/RD5

OC5/IC5/CN13/RD4

dsPIC33FJ64GP706A

dsPIC33FJ128GP706A

= Pins are up to 5V tolerant

dsPIC33FJXXXGPX06A/X08A/X10A

Pin Diagrams (Continued)

80-Pin TQFP

dsPIC33FJ64GP708A

IC5/RD12

OC4/RD3

OC3/RD2

OC2/RD1

CSCK/RG14

AN23/CN23/RA7

AN22/CN22/RA6

C2RX/RG0

C2TX/RG1

C1TX/RF1

C1RX/RF0

CSDO/RG13

CSDI/RG12

OC8/CN16/RD7

OC6/CN14/RD5

OC1/RD0

IC4/RD11

IC2/RD9

IC1/RD8

IC3/RD10

OSC1/CLKIN/RC12

SCL1/RG2

U1RX/RF2

U1TX/RF3

PGEC2/SOSCO/T1CK/CN0/RC14

PGED2/SOSCI/CN1/RC13

REF

+/RA10

REF

-/RA9

U2CTS/AN8/RB8

AN9/RB9

AN10/RB10

AN11/RB11

U2RX/CN17/RF4

IC8/U1RTS/CN21/RD15

U2TX/CN18/RF5

PGEC1/AN6/OCFA/RB6

PGED1/AN7/RB7

AN17/T3CK/T6CK/RC2

AN18/T4CK/T9CK/RC3

AN19/T5CK/T8CK/RC4

SCK2/CN8/RG6

SDI2/CN9/RG7

SDO2/CN10/RG8

MCLR

SS2/CN11/RG9

AN4/CN6/RB4

AN3/CN5/RB3

AN2/SS1/CN4/RB2

PGEC3/AN1/CN3/RB1

PGED3/AN0/CN2/RB0

COFS/RG15

AN16/T2CK/T7CK/RC1

TDO/AN21/INT2/RA13

TMS/AN20/INT1/RA12

TCK/AN12/RB12

TDI/AN13/RB13

U2RTS/AN14/RB14

AN15/OCFB/CN12/RB15

CAP

OC5/CN13/RD4

IC6/CN19/RD13

SDA1/RG3

SDI1/RF7

SDO1/RF8

AN5/CN7/RB5

OSC2/CLKO/RC15

OC7/CN15/RD6

SCK1/INT0/RF6

IC7/U1CTS/CN20/RD14

SDA2/INT4/RA3

SCL2/INT3/RA2

dsPIC33FJ128GP708A

= Pins are up to 5V tolerant

dsPIC33FJXXXGPX06A/X08A/X10A

Pin Diagrams (Continued)

OC6/CN14/RD5

OC5/CN13/RD4

IC6/CN19/RD13

IC5/RD12

OC4/RD3

OC3/RD2

OC2/RD1

AN23/CN23/RA7

AN22/CN22/RA6

AN26/RE2

CSDO/RG13

CSDI/RG12

CSCK/RG14

AN25/RE1

AN24/RE0

RG0

AN28/RE4

AN27/RE3

RF0

CAP

PGED2/SOSCI/CN1/RC13

OC1/RD0

IC3/RD10

IC2/RD9

IC1/RD8

IC4/RD11

SDA2/RA3

SCL2/RA2

OSC2/CLKO/RC15

OSC1/CLKIN/RC12

SCL1/RG2

SCK1/INT0/RF6

SDI1/RF7

SDO1/RF8

SDA1/RG3

U1RX/RF2

U1TX/RF3

PGEC2/SOSCO/T1CK/CN0/RC14

REF

+/RA10

REF

-/RA9

AN8/RB8

AN9/RB9

AN10/RB10

AN11/RB11

U2CTS/RF12

U2RTS/RF13

IC7/U1CTS/CN20/RD14

IC8/U1RTS/CN21/RD15

PGEC1/AN6/OCFA/RB6

PGED1/AN7/RB7

U2TX/CN18/RF5

U2RX/CN17/RF4

AN29/RE5

AN30/RE6

AN31/RE7

AN16/T2CK/T7CK/RC1

AN17/T3CK/T6CK/RC2

AN18/T4CK/T9CK/RC3

AN19/T5CK/T8CK/RC4

SCK2/CN8/RG6

TMS/RA0

AN20/INT1/RA12

AN21/INT2/RA13

AN5/CN7/RB5

AN4/CN6/RB4

AN3/CN5/RB3

AN2/SS1/CN4/RB2

SDI2/CN9/RG7

SDO2/CN10/RG8

PGEC3/AN1/CN3/RB1

PGED3/AN0/CN2/RB0

COFS/RG15

SS2/CN11/RG9

MCLR

AN12/RB12

AN13/RB13

AN14/RB14

AN15/OCFB/CN12/RB15

RG1

RF1

OC8/CN16/RD7

OC7/CN15/RD6

TDO/RA5

INT4/RA15

INT3/RA14

TDI/RA4

TCK/RA1

100-Pin TQFP

dsPIC33FJ64GP310A

dsPIC33FJ128GP310A

100

= Pins are up to 5V tolerant

dsPIC33FJXXXGPX06A/X08A/X10A

Pin Diagrams (Continued)

OC6/CN14/RD5

OC5/CN13/RD4

IC6/CN19/RD13

IC5/RD12

OC4/RD3

OC3/RD2

OC2/RD1

AN23/CN23/RA7

AN22/CN22/RA6

AN26/RE2

CSDO/RG13

CSDI/RG12

CSCK/RG14

AN25/RE1

AN24/RE0

RG0

AN28/RE4

AN27/RE3

C1RX/RF0

CAP

PGED2/SOSCI/CN1/RC13

OC1/RD0

IC3/RD10

IC2/RD9

IC1/RD8

IC4/RD11

SDA2/RA3

SCL2/RA2

OSC2/CLKO/RC15

OSC1/CLKIN/RC12

SCL1/RG2

SCK1/INT0/RF6

SDI1/RF7

SDO1/RF8

SDA1/RG3

U1RX/RF2

U1TX/RF3

PGEC2/SOSCO/T1CK/CN0/RC14

REF

+/RA10

REF

-/RA9

AN8/RB8

AN9/RB9

AN10/RB10

AN11/RB11

U2CTS/RF12

U2RTS/RF13

IC7/U1CTS/CN20/RD14

IC8/U1RTS/CN21/RD15

PGEC1/AN6/OCFA/RB6

PGED1/AN7/RB7

U2TX/CN18/RF5

U2RX/CN17/RF4

AN29/RE5

AN30/RE6

AN31/RE7

AN16/T2CK/T7CK/RC1

AN17/T3CK/T6CK/RC2

AN18/T4CK/T9CK/RC3

AN19/T5CK/T8CK/RC4

SCK2/CN8/RG6

TMS/RA0

AN20/INT1/RA12

AN21/INT2/RA13

AN5/CN7/RB5

AN4/CN6/RB4

AN3/CN5/RB3

AN2/SS1/CN4/RB2

SDI2/CN9/RG7

SDO2/CN10/RG8

PGEC3/AN1/CN3/RB1

PGED3/AN0/CN2/RB0

COFS/RG15

SS2/CN11/RG9

MCLR

AN12/RB12

AN13/RB13

AN14/RB14

AN15/OCFB/CN12/RB15

RG1

C1TX/RF1

OC8/CN16/RD7

OC7/CN15/RD6

TDO/RA5

INT4/RA15

INT3/RA14

TDI/RA4

TCK/RA1

100-Pin TQFP

dsPIC33FJ256GP510A

100

= Pins are up to 5V tolerant

dsPIC33FJXXXGPX06A/X08A/X10A

Pin Diagrams (Continued)

OC6/CN14/RD5

OC5/CN13/RD4

IC6/CN19/RD13

IC5/RD12

OC4/RD3

OC3/RD2

OC2/RD1

AN23/CN23/RA7

AN22/CN22/RA6

AN26/RE2

CSDO/RG13

CSDI/RG12

CSCK/RG14

AN25/RE1

AN24/RE0

C2RX/RG0

AN28/RE4

AN27/RE3

C1RX/RF0

CAP

PGED2/SOSCI/CN1/RC13

OC1/RD0

IC3/RD10

IC2/RD9

IC1/RD8

IC4/RD11

SDA2/RA3

SCL2/RA2

OSC2/CLKO/RC15

OSC1/CLKIN/RC12

SCL1/RG2

SCK1/INT0/RF6

SDI1/RF7

SDO1/RF8

SDA1/RG3

U1RX/RF2

U1TX/RF3

PGEC2/SOSCO/T1CK/CN0/RC14

REF

+/RA10

REF

-/RA9

AN8/RB8

AN9/RB9

AN10/RB10

AN11/RB11

U2CTS/RF12

U2RTS/RF13

IC7/U1CTS/CN20/RD14

IC8/U1RTS/CN21/RD15

PGEC1/AN6/OCFA/RB6

PGED1/AN7/RB7

U2TX/CN18/RF5

U2RX/CN17/RF4

AN29/RE5

AN30/RE6

AN31/RE7

AN16/T2CK/T7CK/RC1

AN17/T3CK/T6CK/RC2

AN18/T4CK/T9CK/RC3

AN19/T5CK/T8CK/RC4

SCK2/CN8/RG6

TMS/RA0

AN20/INT1/RA12

AN21/INT2/RA13

AN5/CN7/RB5

AN4/CN6/RB4

AN3/CN5/RB3

AN2/SS1/CN4/RB2

SDI2/CN9/RG7

SDO2/CN10/RG8

PGEC3/AN1/CN3/RB1

PGED3/AN0/CN2/RB0

COFS/RG15

SS2/CN11/RG9

MCLR

AN12/RB12

AN13/RB13

AN14/RB14

AN15/OCFB/CN12/RB15

C2TX/RG1

C1TX/RF1

OC8/CN16/RD7

OC7/CN15/RD6

TDO/RA5

INT4/RA15

INT3/RA14

TDI/RA4

TCK/RA1

100-Pin TQFP

dsPIC33FJ128GP710A

100

dsPIC33FJ256GP710A

dsPIC33FJ64GP710A

= Pins are up to 5V tolerant

dsPIC33FJXXXGPX06A/X08A/X10A

Table of Contents

dsPIC33F Product Families ................................................................................................................................................................... 5

1.0 Device Overview ........................................................................................................................................................................ 21

2.0 Guidelines for Getting Started with 16-Bit Digital Signal Controllers .......................................................................................... 27

3.0 CPU............................................................................................................................................................................................ 31

4.0 Memory Organization ................................................................................................................................................................. 43

5.0 Flash Program Memory.............................................................................................................................................................. 81

6.0 Reset ......................................................................................................................................................................................... 87

7.0 Interrupt Controller ..................................................................................................................................................................... 93

8.0 Direct Memory Access (DMA) .................................................................................................................................................. 139

9.0 Oscillator Configuration ............................................................................................................................................................ 149

10.0 Power-Saving Features............................................................................................................................................................ 159

11.0 I/O Ports ................................................................................................................................................................................... 167

12.0 Timer1 ...................................................................................................................................................................................... 169

13.0 Timer2/3, Timer4/5, Timer6/7 and Timer8/9 ............................................................................................................................ 171

14.0 Input Capture............................................................................................................................................................................ 177

15.0 Output Compare ....................................................................................................................................................................... 179

16.0 Serial Peripheral Interface (SPI)............................................................................................................................................... 183

17.0 Inter-Integrated Circuit™ (I2C™) .............................................................................................................................................. 189

18.0 Universal Asynchronous Receiver Transmitter (UART) ........................................................................................................... 197

19.0 Enhanced CAN (ECAN™) Module ........................................................................................................................................... 203

20.0 Data Converter Interface (DCI) Module.................................................................................................................................... 231

21.0 10-Bit/12-Bit Analog-to-Digital Converter (ADC) ...................................................................................................................... 239

22.0 Special Features ...................................................................................................................................................................... 251

23.0 Instruction Set Summary .......................................................................................................................................................... 259

24.0 Development Support............................................................................................................................................................... 267

25.0 Electrical Characteristics .......................................................................................................................................................... 271

26.0 High Temperature Electrical Characteristics ............................................................................................................................ 319

27.0 Packaging Information.............................................................................................................................................................. 327

Appendix A: Migrating from dsPIC33FJXXXGPX06/X08/X10 Devices to dsPIC33FJXXXGPX06A/X08A/X10A Devices ................ 339

Appendix B: Revision History............................................................................................................................................................. 340

Index ................................................................................................................................................................................................. 343

The Microchip Web Site ..................................................................................................................................................................... 347

Customer Change Notification Service .............................................................................................................................................. 347

Customer Support .............................................................................................................................................................................. 347

Reader Response .............................................................................................................................................................................. 348

Product Identification System............................................................................................................................................................. 349

dsPIC33FJXXXGPX06A/X08A/X10A

TO OUR VALUED CUSTOMERS

It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip

products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and

enhanced as new volumes and updates are introduced.

If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via

E-mail at docerrors@microchip.com or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We wel-

come your feedback.

Most Current Data Sheet

To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at:

http://www.microchip.com

You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page.

The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000).

Errata

An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current

devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of

silicon and revision of document to which it applies.

To determine if an errata sheet exists for a particular device, please check with one of the following:

• Microchip’s Worldwide Web site; http://www.microchip.com

• Your local Microchip sales office (see last page)

When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are

using.

Customer Notification System

dsPIC33FJXXXGPX06A/X08A/X10A

NOTES:

dsPIC33FJXXXGPX06A/X08A/X10A

1.0 DEVICE OVERVIEW

This document contains device specific information for

the following devices:

• dsPIC33FJ64GP206A

• dsPIC33FJ64GP306A

• dsPIC33FJ64GP310A

• dsPIC33FJ64GP706A

• dsPIC33FJ64GP708A

• dsPIC33FJ64GP710A

• dsPIC33FJ128GP206A

• dsPIC33FJ128GP306A

• dsPIC33FJ128GP310A

• dsPIC33FJ128GP706A

• dsPIC33FJ128GP708A

• dsPIC33FJ128GP710A

• dsPIC33FJ256GP506A

• dsPIC33FJ256GP510A

• dsPIC33FJ256GP710A

The dsPIC33FJXXXGPX06A/X08A/X10A General

Purpose Family of device includes devices with a wide

range of pin counts (64, 80 and 100), different program

memory sizes (64 Kbytes, 128 Kbytes and 256 Kbytes)

and different RAM sizes (8 Kbytes, 16 Kbytes and

30 Kbytes).

This feature makes the family suitable for a wide variety

of high-performance digital signal control applications.

The device is pin compatible with the PIC24H family of

devices, and also share a very high degree of

compatibility with the dsPIC30F family devices. This

allows for easy migration between device families as may

be necessitated by the specific functionality,

computational resource and system cost requirements of

the application.

The dsPIC33FJXXXGPX06A/X08A/X10A device fam-

ily employs a powerful 16-bit architecture that seam-

lessly integrates the control features of a

Microcontroller (MCU) with the computational capabili-

ties of a Digital Signal Processor (DSP). The resulting

functionality is ideal for applications that rely on

high-speed, repetitive computations, as well as control.

The DSP engine, dual 40-bit accumulators, hardware

support for division operations, barrel shifter, 17 x 17

multiplier, a large array of 16-bit working registers and

a wide variety of data addressing modes, together

provide the dsPIC33FJXXXGPX06A/X08A/X10A

Central Processing Unit (CPU) with extensive

mathematical processing capability. Flexible and

deterministic interrupt handling, coupled with a

powerful array of peripherals, renders the

dsPIC33FJXXXGPX06A/X08A/X10A devices suitable

for control applications. Further, Direct Memory Access

(DMA) enables overhead-free transfer of data between

several peripherals and a dedicated DMA RAM.

Reliable, field programmable Flash program memory

ensures scalability of applications that use

dsPIC33FJXXXGPX06A/X08A/X10A devices.

Figure 1-1 illustrates a general block diagram of the

various core and peripheral modules in the

dsPIC33FJXXXGPX06A/X08A/X10A family of devices.

Table 1-1 provides the functions of the various pins

illustrated in the pinout diagrams.

Note: This data sheet summarizes the features

of the dsPIC33FJXXXGPX06A/X08A/

X10A family of devices. However, it is not

intended to be a comprehensive

reference source. To complement the

information in this data sheet, refer to the

latest family reference sections of the

“dsPIC33F/PIC24H Family Reference

Manual”, which are available from the

Microchip website (www.microchip.com).

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 1-1: dsPIC33FJXXXGPX06A/X08A/X10A GENERAL BLOCK DIAGRAM

OSC1/CLKI

OSC2/CLKO

VDD, VSS

Timing

Generation

MCLR

Power-up

Timer

Oscillator

Start-up Timer

Power-on

Reset

Watchdog

Timer

Brown-out

Reset

Precision

Reference

Band Gap

FRC/LPRC

Oscillators

Regulator

Voltage

VCAP

UART1,2

ECAN1,2

DCI

IC1-8 SPI1,2 I2C1,2

OC/

PORTA

Note: Not all pins or features are implemented on all device pinout configurations. See the “Pin Diagrams” section for the

specific pins and features present on each device.

PWM1-8

CN1-23

Instruction

Decode and

Control

PCH PCL

Program Counter

16-bit ALU

Instruction Reg

PCU

16 x 16

W Register Array

ROM Latch

EA MUX

Interrupt

Controller

PSV and Table

Data Access

Control Block

Stack

Control

Logic

Loop

Control

Logic

Data Latch

Address

Latch

Address Latch

Program Memory

Data Latch

Literal Data

16 16

Data Latch

Address

Latch

X RAM Y RAM

Y Data Bus

X Data Bus

DSP Engine

Divide Support

DMA

RAM

DMA

Controller

Control Signals

to Various Blocks

ADC1,2

Timers

PORTB

PORTC

PORTD

PORTE

PORTF

PORTG

Address Generator Units

1-9

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 1-1: PINOUT I/O DESCRIPTIONS

Pin Name Pin

Type

Buffer

Type Description

AN0-AN31 I Analog Analog input channels.

AVDD P P Positive supply for analog modules. This pin must be connected at all times.

AVSS P P Ground reference for analog modules.

CLKI

CLKO

ST/CMOS

—

External clock source input. Always associated with OSC1 pin function.

Oscillator crystal output. Connects to crystal or resonator in Crystal Oscillator

mode. Optionally functions as CLKO in RC and EC modes. Always associated

with OSC2 pin function.

CN0-CN23 I ST Input change notification inputs.

Can be software programmed for internal weak pull-ups on all inputs.

COFS

CSCK

CSDI

CSDO

I/O

—

Data Converter Interface frame synchronization pin.

Data Converter Interface serial clock input/output pin.

Data Converter Interface serial data input pin.

Data Converter Interface serial data output pin.

C1RX

C1TX

C2RX

C2TX

—

ECAN1 bus receive pin.

ECAN1 bus transmit pin.

ECAN2 bus receive pin.

ECAN2 bus transmit pin.

PGED1

PGEC1

PGED2

PGEC2

PGED3

PGEC3

I/O

Data I/O pin for programming/debugging communication channel 1.

Clock input pin for programming/debugging communication channel 1.

Data I/O pin for programming/debugging communication channel 2.

Clock input pin for programming/debugging communication channel 2.

Data I/O pin for programming/debugging communication channel 3.

Clock input pin for programming/debugging communication channel 3.

IC1-IC8 I ST Capture inputs 1 through 8.

INT0

INT1

INT2

INT3

INT4

External interrupt 0.

External interrupt 1.

External interrupt 2.

External interrupt 3.

External interrupt 4.

MCLR I/P ST Master Clear (Reset) input. This pin is an active-low Reset to the device.

OCFA

OCFB

OC1-OC8

—

Compare Fault A input (for Compare Channels 1, 2, 3 and 4).

Compare Fault B input (for Compare Channels 5, 6, 7 and 8).

Compare outputs 1 through 8.

OSC1

OSC2

I/O

ST/CMOS

—

Oscillator crystal input. ST buffer when configured in RC mode;

CMOS otherwise.

Oscillator crystal output. Connects to crystal or resonator in Crystal Oscillator

mode. Optionally functions as CLKO in RC and EC modes.

RA0-RA7

RA9-RA10

RA12-RA15

I/O

PORTA is a bidirectional I/O port.

RB0-RB15 I/O ST PORTB is a bidirectional I/O port.

RC1-RC4

RC12-RC15

I/O

PORTC is a bidirectional I/O port.

RD0-RD15 I/O ST PORTD is a bidirectional I/O port.

RE0-RE7 I/O ST PORTE is a bidirectional I/O port.

RF0-RF8

RF12-RF13

I/O

PORTF is a bidirectional I/O port.

Legend: CMOS = CMOS compatible input or output; Analog = Analog input; P = Power

ST = Schmitt Trigger input with CMOS levels; O = Output; I = Input

dsPIC33FJXXXGPX06A/X08A/X10A

RG0-RG3

RG6-RG9

RG12-RG15

I/O

PORTG is a bidirectional I/O port.

SCK1

SDI1

SDO1

SS1

SCK2

SDI2

SDO2

SS2

I/O

—

Synchronous serial clock input/output for SPI1.

SPI1 data in.

SPI1 data out.

SPI1 slave synchronization or frame pulse I/O.

Synchronous serial clock input/output for SPI2.

SPI2 data in.

SPI2 data out.

SPI2 slave synchronization or frame pulse I/O.

SCL1

SDA1

SCL2

SDA2

I/O

Synchronous serial clock input/output for I2C1.

Synchronous serial data input/output for I2C1.

Synchronous serial clock input/output for I2C2.

Synchronous serial data input/output for I2C2.

SOSCI

SOSCO

ST/CMOS

—

32.768 kHz low-power oscillator crystal input; CMOS otherwise.

32.768 kHz low-power oscillator crystal output.

TMS

TCK

TDI

TDO

—

JTAG Test mode select pin.

JTAG test clock input pin.

JTAG test data input pin.

JTAG test data output pin.

T1CK

T2CK

T3CK

T4CK

T5CK

T6CK

T7CK

T8CK

T9CK

Timer1 external clock input.

Timer2 external clock input.

Timer3 external clock input.

Timer4 external clock input.

Timer5 external clock input.

Timer6 external clock input.

Timer7 external clock input.

Timer8 external clock input.

Timer9 external clock input.

U1CTS

U1RTS

U1RX

U1TX

U2CTS

U2RTS

U2RX

U2TX

—

UART1 clear to send.

UART1 ready to send.

UART1 receive.

UART1 transmit.

UART2 clear to send.

UART2 ready to send.

UART2 receive.

UART2 transmit.

VDD P — Positive supply for peripheral logic and I/O pins.

VCAP P — CPU logic flter capacitor connection.

VSS P — Ground reference for logic and I/O pins.

VREF+ I Analog Analog voltage reference (high) input.

VREF- I Analog Analog voltage reference (low) input.

TABLE 1-1: PINOUT I/O DESCRIPTIONS (CONTINUED)

Pin Name Pin

Type

Buffer

Type Description

Legend: CMOS = CMOS compatible input or output; Analog = Analog input; P = Power

ST = Schmitt Trigger input with CMOS levels; O = Output; I = Input

dsPIC33FJXXXGPX06A/X08A/X10A

1.1 Referenced Sources

This device data sheet is based on the following

individual chapters of the “dsPIC33F/PIC24H Family

Reference Manual”. These documents should be

considered as the general reference for the operation

of a particular module or device feature.

•Section 1. “Introduction” (DS70197)

•Section 2. “CPU” (DS70204)

•Section 3. “Data Memory” (DS70202)

•Section 4. “Program Memory” (DS70203)

•Section 5. “Flash Programming” (DS70191)

•Section 6. “Interrupts” (DS70184)

•Section 7. “Oscillator” (DS70186)

•Section 8. “Reset” (DS70192)

•Section 9. “Watchdog Timer and Power-Saving Modes” (DS70196)

•Section 10. “I/O Ports” (DS70193)

•Section 11. “Timers” (DS70205)

•Section 12. “Input Capture” (DS70198)

•Section 13. “Output Compare” (DS70209)

•Section 16. “Analog-to-Digital Converter (ADC)” (DS70183)

•Section 17. “UART” (DS70188)

•Section 18. “Serial Peripheral Interface (SPI)” (DS70206)

•Section 19. “Inter-Integrated Circuit™ (I2C™)” (DS70195)

•Section 20. “Data Converter Interface (DCI)” (DS70288)

•Section 21. “Enhanced Controller Area Network (ECAN™)” (DS70185)

•Section 22. “Direct Memory Access (DMA)” (DS70182)

•Section 23. “CodeGuard™ Security” (DS70199)

•Section 24. “Programming and Diagnostics” (DS70207)

•Section 25. “Device Configuration” (DS70194)

•Section 26. “Development Tool Support” (DS70200)

Note: To access the documents listed below,

browse to the documentation section of

the dsPIC33FJ256GP710A product page

on the Microchip web site

(www.microchip.com) or select a family

reference manual section from the

following list.

In addition to parameters, features, and

other documentation, the resulting page

provides links to the related family

reference manual sections.

dsPIC33FJXXXGPX06A/X08A/X10A

NOTES:

dsPIC33FJXXXGPX06A/X08A/X10A

2.0 GUIDELINES FOR GETTING

STARTED WITH 16-BIT

DIGITAL SIGNAL

CONTROLLERS

2.1 Basic Connection Requirements

Getting started with the dsPIC33FJXXXGPX06A/

X08A/X10A family of 16-bit Digital Signal Controllers

(DSCs) requires attention to a minimal set of device pin

connections before proceeding with development. The

following is a list of pin names, which must always be

connected:

• All VDD and VSS pins

(see Section 2.2 “Decoupling Capacitors”)

• All AVDD and AVSS pins (regardless if ADC module

is not used)

(see Section 2.2 “Decoupling Capacitors”)

•V

CAP

(see Section 2.3 “CPU Logic Filter Capacitor

Connection (Vcap)”)

•MCLR

(see Section 2.4 “Master Clear (MCLR) Pin”)

• PGECx/PGEDx pins used for In-Circuit Serial

Programming™ (ICSP™) and debugging purposes

(see Section 2.5 “ICSP Pins”)

• OSC1 and OSC2 pins when external oscillator

source is used

(see Section 2.6 “External Oscillator Pins”)

Additionally, the following pins may be required:

•V

REF+/VREF- pins used when external voltage

reference for ADC module is implemented

2.2 Decoupling Capacitors

The use of decoupling capacitors on every pair of

power supply pins, such as VDD, VSS, AVDD and

AVSS is required.

Consider the following criteria when using decoupling

capacitors:

•Value and type of capacitor: Recommendation

of 0.1 µF (100 nF), 10-20V. This capacitor should

be a low-ESR and have resonance frequency in

the range of 20 MHz and higher. It is

recommended that ceramic capacitors be used.

•Placement on the printed circuit board: The

decoupling capacitors should be placed as close

to the pins as possible. It is recommended to

place the capacitors on the same side of the

board as the device. If space is constricted, the

capacitor can be placed on another layer on the

PCB using a via; however, ensure that the trace

length from the pin to the capacitor is within

one-quarter inch (6 mm) in length.

•Handling high frequency noise: If the board is

experiencing high frequency noise, upward of

tens of MHz, add a second ceramic-type capacitor

in parallel to the above described decoupling

capacitor. The value of the second capacitor can

be in the range of 0.01 µF to 0.001 µF. Place this

second capacitor next to the primary decoupling

capacitor. In high-speed circuit designs, consider

implementing a decade pair of capacitances as

close to the power and ground pins as possible.

For example, 0.1 µF in parallel with 0.001 µF.

•Maximizing performance: On the board layout

from the power supply circuit, run the power and

return traces to the decoupling capacitors first,

and then to the device pins. This ensures that the

decoupling capacitors are first in the power chain.

Equally important is to keep the trace length

between the capacitor and the power pins to a

minimum thereby reducing PCB track inductance.

Note 1: This data sheet summarizes the features

of the dsPIC33FJXXXGPX06A/X08A/

X10A family of devices. It is not intended

to be a comprehensive reference source.

To complement the information in this

data sheet, refer to the “dsPIC33F/

PIC24H Family Reference Manual”.

Please see the Microchip web site

(www.microchip.com) for the latest

dsPIC33F/PIC24H Family Reference

Manual sections.

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Note: The AVDD and AVSS pins must be

connected independent of the ADC

voltage reference source.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 2-1: RECOMMENDED

MINIMUM CONNECTION

2.2.1 TANK CAPACITORS

On boards with power traces running longer than six

inches in length, it is suggested to use a tank capacitor

for integrated circuits including DSCs to supply a local

power source. The value of the tank capacitor should

be determined based on the trace resistance that con-

nects the power supply source to the device, and the

maximum current drawn by the device in the applica-

tion. In other words, select the tank capacitor so that it

meets the acceptable voltage sag at the device. Typical

values range from 4.7 µF to 47 µF.

2.3 CPU Logic Filter Capacitor

Connection (VCAP)

A low-ESR (< 5 Ohms) capacitor is required on the

VCAP pin, which is used to stabilize the voltage

regulator output voltage. The VCAP pin must not be

connected to VDD, and must have a capacitor between

4.7 µF and 10 µF, 16V connected to ground. The type

can be ceramic or tantalum. Refer to Section 25.0

“Electrical Characteristics” for additional

information.

The placement of this capacitor should be close to the

VCAP. It is recommended that the trace length not

exceed one-quarter inch (6 mm). Refer to Section 22.2

“On-Chip Voltage Regulator” for details.

2.4 Master Clear (MCLR) Pin

The MCLR pin provides for two specific device

functions:

• Device Reset

• Device programming and debugging

During device programming and debugging, the

resistance and capacitance that can be added to the

pin must be considered. Device programmers and

debuggers drive the MCLR pin. Consequently,

specific voltage levels (VIH and VIL) and fast signal

transitions must not be adversely affected. Therefore,

specific values of R and C will need to be adjusted

based on the application and PCB requirements.

For example, as shown in Figure 2-2, it is

recommended that the capacitor C, be isolated from

the MCLR pin during programming and debugging

operations.

Place the components shown in Figure 2-2 within

one-quarter inch (6 mm) from the MCLR pin.

FIGURE 2-2: EXAMPLE OF MCLR PIN

CONNECTIONS

dsPIC33F

VDD

VSS

VDD

VSS

VDD

AVDD

AVSS

VDD

VSS

0.1 µF

Ceramic

0.1 µF

Ceramic

0.1 µF

Ceramic

0.1 µF

Ceramic

VDD

MCLR

0.1 µF

Ceramic

VCAP

10 Ω

Note 1: R≤ 10 kΩ is recommended. A suggested

starting value is 10 kΩ. Ensure that the

MCLR pin VIH and VIL specifications are met.

2: R1 ≤ 470Ω will limit any current flowing into

MCLR from the external capacitor C, in the

event of MCLR pin breakdown, due to

Electrostatic Discharge (ESD) or Electrical

Overstress (EOS). Ensure that the MCLR pin

VIH and VIL specifications are met.

VDD

MCLR

dsPIC33F

dsPIC33FJXXXGPX06A/X08A/X10A

2.5 ICSP Pins

The PGECx and PGEDx pins are used for In-Circuit

Serial Programming™ (ICSP™) and debugging pur-

poses. It is recommended to keep the trace length

between the ICSP connector and the ICSP pins on the

device as short as possible. If the ICSP connector is

expected to experience an ESD event, a series resistor

is recommended, with the value in the range of a few

tens of Ohms, not to exceed 100 Ohms.

Pull-up resistors, series diodes, and capacitors on the

PGECx and PGEDx pins are not recommended as they

will interfere with the programmer/debugger communi-

cations to the device. If such discrete components are

an application requirement, they should be removed

from the circuit during programming and debugging.

Alternatively, refer to the AC/DC characteristics and

timing requirements information in the respective

device Flash programming specification for information

on capacitive loading limits and pin input voltage high

(VIH) and input low (VIL) requirements.

Ensure that the “Communication Channel Select” (i.e.,

PGECx/PGEDx pins) programmed into the device

matches the physical connections for the ICSP to

MPLAB® ICD 2, MPLAB ICD 3 or MPLAB REAL ICE™.

For more information on ICD 2, ICD 3 and REAL ICE

connection requirements, refer to the following

documents that are available on the Microchip website.

•“MPLAB® ICD 2 In-Circuit Debugger User’s

Guide” DS51331

•“Using MPLAB® ICD 2” (poster) DS51265

•“MPLAB® ICD 2 Design Advisory” DS51566

•“Using MPLAB® ICD 3 In-Circuit Debugger”

(poster) DS51765

•“MPLAB® ICD 3 Design Advisory” DS51764

•“MPLAB® REAL ICE™ In-Circuit Emulator User’s

Guide” DS51616

•“Using MPLAB® REAL ICE™” (poster) DS51749

2.6 External Oscillator Pins

Many DSCs have options for at least two oscillators: a

high-frequency primary oscillator and a low-frequency

secondary oscillator (refer to Section 9.0 “Oscillator

Configuration” for details).

The oscillator circuit should be placed on the same

side of the board as the device. Also, place the

oscillator circuit close to the respective oscillator pins,

not exceeding one-half inch (12 mm) distance

between them. The load capacitors should be placed

next to the oscillator itself, on the same side of the

board. Use a grounded copper pour around the

oscillator circuit to isolate them from surrounding

circuits. The grounded copper pour should be routed

directly to the MCU ground. Do not run any signal

traces or power traces inside the ground pour. Also, if

using a two-sided board, avoid any traces on the

other side of the board where the crystal is placed. A

suggested layout is shown in Figure 2-3.

FIGURE 2-3: SUGGESTED PLACEMENT

OF THE OSCILLATOR

CIRCUIT

Main Oscillator

Guard Ring

Guard Trace

Secondary

Oscillator

dsPIC33FJXXXGPX06A/X08A/X10A

2.7 Oscillator Value Conditions on

Device Start-up

If the PLL of the target device is enabled and

configured for the device start-up oscillator, the

maximum oscillator source frequency must be limited

to ≤8 MHz for start-up with PLL enabled to comply with

device PLL start-up conditions. This means that if the

external oscillator frequency is outside this range, the

application must start-up in the FRC mode first. The

default PLL settings after a POR with an oscillator

frequency outside this range will violate the device

operating speed.

Once the device powers up, the application firmware

can initialize the PLL SFRs, CLKDIV and PLLDBF to a

suitable value, and then perform a clock switch to the

Oscillator + PLL clock source. Note that clock switching

must be enabled in the device Configuration word.

2.8 Configuration of Analog and

Digital Pins During ICSP

Operations

If MPLAB ICD 2, ICD 3 or REAL ICE is selected as a

debugger, it automatically initializes all of the A/D input

pins (ANx) as “digital” pins, by setting all bits in the

ADPCFG and ADPCFG2 registers.

The bits in the registers that correspond to the A/D pins

that are initialized by MPLAB ICD 2, ICD 3 or REAL

ICE, must not be cleared by the user application

firmware; otherwise, communication errors will result

between the debugger and the device.

If your application needs to use certain A/D pins as

analog input pins during the debug session, the user

application must clear the corresponding bits in the

ADPCFG and ADPCFG2 registers during initialization

of the ADC module.

When MPLAB ICD 2, ICD 3 or REAL ICE is used as a

programmer, the user application firmware must

correctly configure the ADPCFG and ADPCFG2

registers. Automatic initialization of these registers is

only done during debugger operation. Failure to

correctly configure the register(s) will result in all A/D

pins being recognized as analog input pins, resulting in

the port value being read as a logic ‘0’, which may

affect user application functionality.

2.9 Unused I/Os

Unused I/O pins should be configured as outputs and

driven to a logic-low state.

Alternatively, connect a 1k to 10k resistor between VSS

and the unused pins.

dsPIC33FJXXXGPX06A/X08A/X10A

3.0 CPU

The dsPIC33FJXXXGPX06A/X08A/X10A CPU module

has a 16-bit (data) modified Harvard architecture with an

enhanced instruction set, including significant support for

DSP. The CPU has a 24-bit instruction word with a variable

length opcode field. The Program Counter (PC) is 23 bits

wide and addresses up to 4M x 24 bits of user program

memory space. The actual amount of program memory

implemented varies by device. A single-cycle instruction

prefetch mechanism is used to help maintain throughput

and provides predictable execution. All instructions execute

in a single cycle, with the exception of instructions that

change the program flow, the double word move (

MOV.D

)

instruction and the table instructions. Overhead-free pro-

gram loop constructs are supported using the

and

REPEAT

instructions, both of which are interruptible at any

point.

The dsPIC33FJXXXGPX06A/X08A/X10A devices have

sixteen, 16-bit working registers in the programmer’s

model. Each of the working registers can serve as a data,

address or address offset register. The 16th working regis-

ter (W15) operates as a software Stack Pointer (SP) for

interrupts and calls.

The dsPIC33FJXXXGPX06A/X08A/X10A instruction set

has two classes of instructions: MCU and DSP. These two

instruction classes are seamlessly integrated into a single

CPU. The instruction set includes many addressing modes

and is designed for optimum C compiler efficiency. For most

instructions, the dsPIC33FJXXXGPX06A/X08A/X10A is

capable of executing a data (or program data) memory

read, a working register (data) read, a data memory write

and a program (instruction) memory read per instruction

cycle. As a result, three parameter instructions can be sup-

ported, allowing A + B = C operations to be executed in a

single cycle.

A block diagram of the CPU is shown in Figure 3-1. The

programmer’s model for the dsPIC33FJXXXGPX06A/

X08A/X10A is shown in Figure 3-2.

3.1 Data Addressing Overview

The data space can be addressed as 32K words or

64 Kbytes and is split into two blocks, referred to as X and

Y data memory. Each memory block has its own indepen-

dent Address Generation Unit (AGU). The MCU class of

instructions operates solely through the X memory AGU,

which accesses the entire memory map as one linear data

space. Certain DSP instructions operate through the X and

Y AGUs to support dual operand reads, which splits the

data address space into two parts. The X and Y data space

boundary is device-specific.

Overhead-free circular buffers (Modulo Addressing mode)

are supported in both X and Y address spaces. The Modulo

Addressing removes the software boundary checking over-

head for DSP algorithms. Furthermore, the X AGU circular

addressing can be used with any of the MCU class of

instructions. The X AGU also supports Bit-Reversed

Addressing to greatly simplify input or output data

reordering for radix-2 FFT algorithms.

The upper 32 Kbytes of the data space memory map can

optionally be mapped into program space at any 16K pro-

gram word boundary defined by the 8-bit Program Space

Visibility Page (PSVPAG) register. The program to data

space mapping feature lets any instruction access program

space as if it were data space. The data space also includes

2 Kbytes of DMA RAM, which is primarily used for DMA

data transfers, but may be used as general purpose RAM.

3.2 DSP Engine Overview

The DSP engine features a high-speed, 17-bit by 17-bit

multiplier, a 40-bit ALU, two 40-bit saturating accumula-

tors and a 40-bit bidirectional barrel shifter. The barrel

shifter is capable of shifting a 40-bit value, up to 16 bits

right or left, in a single cycle. The DSP instructions operate

seamlessly with all other instructions and have been

designed for optimal real-time performance. The

MAC

instruction and other associated instructions can concur-

rently fetch two data operands from memory while multi-

plying two W registers and accumulating and optionally

saturating the result in the same cycle. This instruction

functionality requires that the RAM memory data space be

split for these instructions and linear for all others. Data

space partitioning is achieved in a transparent and flexible

manner through dedicating certain working registers to

each address space.

3.3 Special MCU Features

The dsPIC33FJXXXGPX06A/X08A/X10A features a

17-bit by 17-bit, single-cycle multiplier that is shared by

both the MCU ALU and DSP engine. The multiplier can

perform signed, unsigned and mixed-sign multiplication.

Using a 17-bit by 17-bit multiplier for 16-bit by 16-bit mul-

tiplication not only allows you to perform mixed-sign multi-

plication, it also achieves accurate results for special

operations, such as (-1.0) x (-1.0).

The dsPIC33FJXXXGPX06A/X08A/X10A supports 16/16

and 32/16 divide operations, both fractional and integer.

All divide instructions are iterative operations. They must

be executed within a

REPEAT

loop, resulting in a total exe-

cution time of 19 instruction cycles. The divide operation

can be interrupted during any of those 19 cycles without

loss of data.

A 40-bit barrel shifter is used to perform up to a 16-bit, left

or right shift in a single cycle. The barrel shifter can be used

by both MCU and DSP instructions.

Note 1: This data sheet summarizes the features

of the dsPIC33FJXXXGPX06A/X08A/

X10A family of devices. However, it is not

intended to be a comprehensive refer-

ence source. To complement the infor-

mation in this data sheet, refer to Section

2. “CPU” (DS70204) in the “dsPIC33F/

PIC24H Family Reference Manual”,

which is available from the Microchip web

site (www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 3-1: dsPIC33FJXXXGPX06A/X08A/X10A CPU CORE BLOCK DIAGRAM

Instruction

Decode and

Control

PCH PCL

Program Counter

16-bit ALU

Instruction Reg

PCU

16 x 16

W Register Array

ROM Latch

EA MUX

Interrupt

Controller

Stack

Control

Logic

Loop

Control

Logic

Data Latch

Address

Latch

Control Signals

to Various Blocks

Literal Data

16 16

To Peripheral Modules

Data Latch

Address

Latch

X RAM Y RAM

Address Generator Units

Y Data Bus

X Data Bus

DMA

Controller

DMA

RAM

DSP Engine

Divide Support

PSV and Table

Data Access

Control Block

Program Memory

Data Latch

Address Latch

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 3-2: dsPIC33FJXXXGPX06A/X08A/X10A PROGRAMMER’S MODEL

PC22 PC0

7 0

D0D15

Program Counter

Data Table Page Address

STATUS Register

Working Registers

DSP Operand

Registers

W10

W11

W12/DSP Offset

W13/DSP Write Back

W14/Frame Pointer

W15/Stack Pointer

DSP Address

Registers

AD39 AD0AD31

DSP

Accumulators

AccA

AccB

7 0

Program Space Visibility Page Address

OA OB SA SB

RCOUNT

15 0

REPEAT Loop Counter

DCOUNT

15 0

DO Loop Counter

DOSTART

22 0

DO Loop Start Address

IPL2 IPL1

SPLIM Stack Pointer Limit Register

AD15

SRL

PUSH.S Shadow

DO Shadow

OAB SAB

15 0

Core Configuration Register

Legend

CORCON

DA DC RA N

TBLPAG

PSVPAG

IPL0 OV

W0/WREG

SRH

DO Loop End Address

DOEND

dsPIC33FJXXXGPX06A/X08A/X10A

3.4 CPU Control Registers

CPU control registers include:

•SR: CPU Status Register

•CORCON: Core Control Register

R-0 R-0 R/C-0 R/C-0 R-0 R/C-0 R -0 R/W-0

OA OB SA(1) SB(1) OAB SAB DA DC

bit 15 bit 8

R/W-0(2) R/W-0(3) R/W-0(3) R-0 R/W-0 R/W-0 R/W-0 R/W-0

IPL<2:0>(2) RA N OV Z C

bit 7 bit 0

Legend:

C = Clear only bit R = Readable bit U = Unimplemented bit, read as ‘0’

S = Set only bit W = Writable bit -n = Value at POR

‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 OA: Accumulator A Overflow Status bit

1 = Accumulator A overflowed

0 = Accumulator A has not overflowed

bit 14 OB: Accumulator B Overflow Status bit

1 = Accumulator B overflowed

0 = Accumulator B has not overflowed

bit 13 SA: Accumulator A Saturation ‘Sticky’ Status bit(1)

1 = Accumulator A is saturated or has been saturated at some time

0 = Accumulator A is not saturated

bit 12 SB: Accumulator B Saturation ‘Sticky’ Status bit(1)

1 = Accumulator B is saturated or has been saturated at some time

0 = Accumulator B is not saturated

bit 11 OAB: OA || OB Combined Accumulator Overflow Status bit

1 = Accumulators A or B have overflowed

0 = Neither Accumulators A or B have overflowed

bit 10 SAB: SA || SB Combined Accumulator ‘Sticky’ Status bit

1 = Accumulators A or B are saturated or have been saturated at some time in the past

0 = Neither Accumulator A or B are saturated

Note: This bit may be read or cleared (not set). Clearing this bit will clear SA and SB.

bit 9 DA: DO Loop Active bit

1 = DO loop in progress

0 = DO loop not in progress

Note 1: This bit may be read or cleared (not set).

2: The IPL<2:0> bits are concatenated with the IPL<3> bit (CORCON<3>) to form the CPU Interrupt Priority

Level. The value in parentheses indicates the IPL if IPL<3> = 1. User interrupts are disabled when

IPL<3> = 1.

3: The IPL<2:0> Status bits are read only when NSTDIS = 1 (INTCON1<15>).

dsPIC33FJXXXGPX06A/X08A/X10A

bit 8 DC: MCU ALU Half Carry/Borrow bit

1 = A carry-out from the 4th low-order bit (for byte sized data) or 8th low-order bit (for word sized data)

of the result occurred

0 = No carry-out from the 4th low-order bit (for byte sized data) or 8th low-order bit (for word sized

data) of the result occurred

bit 7-5 IPL<2:0>: CPU Interrupt Priority Level Status bits(2)

111 = CPU Interrupt Priority Level is 7 (15), user interrupts disabled

110 = CPU Interrupt Priority Level is 6 (14)

101 = CPU Interrupt Priority Level is 5 (13)

100 = CPU Interrupt Priority Level is 4 (12)

011 = CPU Interrupt Priority Level is 3 (11)

010 = CPU Interrupt Priority Level is 2 (10)

001 = CPU Interrupt Priority Level is 1 (9)

000 = CPU Interrupt Priority Level is 0 (8)

bit 4 RA: REPEAT Loop Active bit

1 = REPEAT loop in progress

0 = REPEAT loop not in progress

bit 3 N: MCU ALU Negative bit

1 = Result was negative

0 = Result was non-negative (zero or positive)

bit 2 OV: MCU ALU Overflow bit

This bit is used for signed arithmetic (2’s complement). It indicates an overflow of the magnitude which

causes the sign bit to change state.

1 = Overflow occurred for signed arithmetic (in this arithmetic operation)

0 = No overflow occurred

bit 1 Z: MCU ALU Zero bit

1 = An operation which affects the Z bit has set it at some time in the past

0 = The most recent operation which affects the Z bit has cleared it (i.e., a non-zero result)

bit 0 C: MCU ALU Carry/Borrow bit

1 = A carry-out from the Most Significant bit of the result occurred

0 = No carry-out from the Most Significant bit of the result occurred

Note 1: This bit may be read or cleared (not set).

2: The IPL<2:0> bits are concatenated with the IPL<3> bit (CORCON<3>) to form the CPU Interrupt Priority

Level. The value in parentheses indicates the IPL if IPL<3> = 1. User interrupts are disabled when

IPL<3> = 1.

3: The IPL<2:0> Status bits are read only when NSTDIS = 1 (INTCON1<15>).

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 R/W-0 R/W-0 R-0 R-0 R-0

— — —USEDT

(1) DL<2:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-1 R/W-0 R/C-0 R/W-0 R/W-0 R/W-0

SATA SATB SATDW ACCSAT IPL3(2) PSV RND IF

bit 7 bit 0

Legend: C = Clear only bit

R = Readable bit W = Writable bit -n = Value at POR ‘1’ = Bit is set

0’ = Bit is cleared ‘x = Bit is unknown U = Unimplemented bit, read as ‘0’

bit 15-13 Unimplemented: Read as ‘0’

bit 12 US: DSP Multiply Unsigned/Signed Control bit

1 = DSP engine multiplies are unsigned

0 = DSP engine multiplies are signed

bit 11 EDT: Early DO Loop Termination Control bit(1)

1 = Terminate executing DO loop at end of current loop iteration

0 = No effect

bit 10-8 DL<2:0>: DO Loop Nesting Level Status bits

111 = 7 DO loops active

•

001 = 1 DO loop active

000 = 0 DO loops active

bit 7 SATA: AccA Saturation Enable bit

1 = Accumulator A saturation enabled

0 = Accumulator A saturation disabled

bit 6 SATB: AccB Saturation Enable bit

1 = Accumulator B saturation enabled

0 = Accumulator B saturation disabled

bit 5 SATDW: Data Space Write from DSP Engine Saturation Enable bit

1 = Data space write saturation enabled

0 = Data space write saturation disabled

bit 4 ACCSAT: Accumulator Saturation Mode Select bit

1 = 9.31 saturation (super saturation)

0 = 1.31 saturation (normal saturation)

bit 3 IPL3: CPU Interrupt Priority Level Status bit 3(2)

1 = CPU interrupt priority level is greater than 7

0 = CPU interrupt priority level is 7 or less

bit 2 PSV: Program Space Visibility in Data Space Enable bit

1 = Program space visible in data space

0 = Program space not visible in data space

bit 1 RND: Rounding Mode Select bit

1 = Biased (conventional) rounding enabled

0 = Unbiased (convergent) rounding enabled

bit 0 IF: Integer or Fractional Multiplier Mode Select bit

1 = Integer mode enabled for DSP multiply ops

0 = Fractional mode enabled for DSP multiply ops

Note 1: This bit will always read as ‘0’.

2: The IPL3 bit is concatenated with the IPL<2:0> bits (SR<7:5>) to form the CPU interrupt priority level.

dsPIC33FJXXXGPX06A/X08A/X10A

3.5 Arithmetic Logic Unit (ALU)

The dsPIC33FJXXXGPX06A/X08A/X10A ALU is 16

bits wide and is capable of addition, subtraction, bit

shifts and logic operations. Unless otherwise

mentioned, arithmetic operations are 2’s complement

in nature. Depending on the operation, the ALU may

affect the values of the Carry (C), Zero (Z), Negative

(N), Overflow (OV) and Digit Carry (DC) Status bits in

the SR register. The C and DC Status bits operate as

Borrow and Digit Borrow bits, respectively, for

subtraction operations.

The ALU can perform 8-bit or 16-bit operations,

depending on the mode of the instruction that is used.

Data for the ALU operation can come from the W

addressing mode of the instruction. Likewise, output

data from the ALU can be written to the W register array

or a data memory location.

Refer to the “dsPIC30F/33F Programmer’s Reference

Manual” (DS70157) for information on the SR bits

affected by each instruction.

The dsPIC33FJXXXGPX06A/X08A/X10A CPU

incorporates hardware support for both multiplication

and division. This includes a dedicated hardware

multiplier and support hardware for 16-bit-divisor

division.

3.5.1 MULTIPLIER

Using the high-speed 17-bit x 17-bit multiplier of the DSP

engine, the ALU supports unsigned, signed or mixed-sign

operation in several MCU multiplication modes:

• 16-bit x 16-bit signed

• 16-bit x 16-bit unsigned

• 16-bit signed x 5-bit (literal) unsigned

• 16-bit unsigned x 16-bit unsigned

• 16-bit unsigned x 5-bit (literal) unsigned

• 16-bit unsigned x 16-bit signed

• 8-bit unsigned x 8-bit unsigned

3.5.2 DIVIDER

The divide block supports 32-bit/16-bit and 16-bit/16-bit

signed and unsigned integer divide operations with the

following data sizes:

• 32-bit signed/16-bit signed divide

• 32-bit unsigned/16-bit unsigned divide

• 16-bit signed/16-bit signed divide

• 16-bit unsigned/16-bit unsigned divide

The quotient for all divide instructions ends up in W0

and the remainder in W1. 16-bit signed and unsigned

DIV instructions can specify any W register for both the

16-bit divisor (Wn) and any W register (aligned) pair

(W(m + 1):Wm) for the 32-bit dividend. The divide

algorithm takes one cycle per bit of divisor, so both

32-bit/16-bit and 16-bit/16-bit instructions take the

same number of cycles to execute.

3.6 DSP Engine

The DSP engine consists of a high-speed,

17-bit x 17-bit multiplier, a barrel shifter and a 40-bit

adder/subtracter (with two target accumulators, round

and saturation logic).

The dsPIC33FJXXXGPX06A/X08A/X10A is a sin-

gle-cycle, instruction flow architecture; therefore, concur-

rent operation of the DSP engine with MCU instruction

flow is not possible. However, some MCU ALU and DSP

engine resources may be used concurrently by the same

instruction (e.g., ED, EDAC).

The DSP engine also has the capability to perform

inherent accumulator-to-accumulator operations which

require no additional data. These instructions are ADD,

SUB and NEG.

The DSP engine has various options selected through

various bits in the CPU Core Control register

(CORCON), as listed below:

• Fractional or integer DSP multiply (IF)

• Signed or unsigned DSP multiply (US)

• Conventional or convergent rounding (RND)

• Automatic saturation on/off for AccA (SATA)

• Automatic saturation on/off for AccB (SATB)

• Automatic saturation on/off for writes to data

memory (SATDW)

• Accumulator Saturation mode selection

(ACCSAT)

Table 3-1 provides a summary of DSP instructions. A

block diagram of the DSP engine is shown in

Figure 3-3.

TABLE 3-1: DSP INSTRUCTIONS

SUMMARY

Instruction Algebraic

Operation

ACC Write

Back

CLR A = 0 Yes

ED A = (x – y)2No

EDAC A = A + (x – y)2No

MAC A = A + (x • y) Yes

MAC A = A + x2 No

MOVSAC No change in A Yes

MPY A = x • y No

MPY A = x2No

MPY.N A = – x • y No

MSC A = A – x • y Yes

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 3-3: DSP ENGINE BLOCK DIAGRAM

Zero Backfill

Sign-Extend

Barrel

Shifter

40-bit Accumulator A

40-bit Accumulator B Round

Logic

X Data Bus

To/From W Array

Adder

Saturate

Negate

16 16

40 40

Y Data Bus

Carry/Borrow Out

Carry/Borrow In

Multiplier/Scaler

17-bit

dsPIC33FJXXXGPX06A/X08A/X10A

3.6.1 MULTIPLIER

The 17-bit x 17-bit multiplier is capable of signed or

unsigned operation and can multiplex its output using a

scaler to support either 1.31 fractional (Q31) or 32-bit

integer results. Unsigned operands are zero-extended

into the 17th bit of the multiplier input value. Signed

operands are sign-extended into the 17th bit of the

multiplier input value. The output of the 17-bit x 17-bit

multiplier/scaler is a 33-bit value which is

sign-extended to 40 bits. Integer data is inherently

represented as a signed two’s complement value,

where the Most Significant bit (MSb) is defined as a

sign bit. Generally speaking, the range of an N-bit two’s

complement integer is -2N-1 to 2N-1 - 1. For a 16-bit

integer, the data range is -32768 (0x8000) to 32767

(0x7FFF) including 0. For a 32-bit integer, the data

range is -2,147,483,648 (0x8000 0000) to

2,147,483,647 (0x7FFF FFFF).

When the multiplier is configured for fractional

multiplication, the data is represented as a two’s

complement fraction, where the MSb is defined as a

sign bit and the radix point is implied to lie just after the

sign bit (QX format). The range of an N-bit two’s

complement fraction with this implied radix point is -1.0

to (1 - 21-N). For a 16-bit fraction, the Q15 data range is

-1.0 (0x8000) to 0.999969482 (0x7FFF) including 0

and has a precision of 3.01518x10-5. In Fractional

mode, the 16 x 16 multiply operation generates a 1.31

product which has a precision of 4.65661 x 10-10.

The same multiplier is used to support the MCU

multiply instructions which include integer 16-bit

signed, unsigned and mixed sign multiplies.

The MUL instruction may be directed to use byte or

word sized operands. Byte operands will direct a 16-bit

result, and word operands will direct a 32-bit result to

the specified register(s) in the W array.

3.6.2 DATA ACCUMULATORS AND

ADDER/SUBTRACTER

The data accumulator consists of a 40-bit adder/

subtracter with automatic sign extension logic. It can

select one of two accumulators (A or B) as its

pre-accumulation source and post-accumulation

destination. For the ADD and LAC instructions, the data

to be accumulated or loaded can be optionally scaled

via the barrel shifter prior to accumulation.

3.6.2.1 Adder/Subtracter, Overflow and

Saturation

The adder/subtracter is a 40-bit adder with an optional

zero input into one side, and either true, or complement

data into the other input. In the case of addition, the

Carry/Borrow input is active-high and the other input is

true data (not complemented), whereas in the case of

subtraction, the Carry/Borrow input is active-low and

the other input is complemented. The adder/subtracter

generates Overflow Status bits, SA/SB and OA/OB,

which are latched and reflected in the STATUS

• Overflow from bit 39: this is a catastrophic

overflow in which the sign of the accumulator is

destroyed.

• Overflow into guard bits 32 through 39: this is a

recoverable overflow. This bit is set whenever all

the guard bits are not identical to each other.

The adder has an additional saturation block which

controls accumulator data saturation, if selected. It

uses the result of the adder, the Overflow Status bits

described above and the SAT<A:B> (CORCON<7:6>)

and ACCSAT (CORCON<4>) mode control bits to

determine when and to what value to saturate.

Six STATUS register bits have been provided to

support saturation and overflow; they are:

• OA: AccA overflowed into guard bits

• OB: AccB overflowed into guard bits

• SA: AccA saturated (bit 31 overflow and satura-

tion)

AccA overflowed into guard bits and saturated (bit

39 overflow and saturation)

• SB: AccB saturated (bit 31 overflow and satura-

tion)

AccB overflowed into guard bits and saturated (bit

39 overflow and saturation)

• OAB: Logical OR of OA and OB

• SAB: Logical OR of SA and SB

The OA and OB bits are modified each time data

passes through the adder/subtracter. When set, they

indicate that the most recent operation has overflowed

into the accumulator guard bits (bits 32 through 39).

The OA and OB bits can also optionally generate an

arithmetic warning trap when set and the

corresponding Overflow Trap Flag Enable bits (OVATE,

OVBTE) in the INTCON1 register (refer to Section 7.0

“Interrupt Controller”) are set. This allows the user to

take immediate action, for example, to correct system

gain.

dsPIC33FJXXXGPX06A/X08A/X10A

The SA and SB bits are modified each time data

passes through the adder/subtracter, but can only be

cleared by the user. When set, they indicate that the

accumulator has overflowed its maximum range (bit 31

for 32-bit saturation or bit 39 for 40-bit saturation) and

will be saturated (if saturation is enabled). When

saturation is not enabled, SA and SB default to bit 39

overflow and, thus, indicate that a catastrophic

overflow has occurred. If the COVTE bit in the

INTCON1 register is set, SA and SB bits will generate

an arithmetic warning trap when saturation is disabled.

The Overflow and Saturation Status bits can optionally

be viewed in the STATUS Register (SR) as the logical

OR of OA and OB (in bit OAB) and the logical OR of SA

and SB (in bit SAB). This allows programmers to check

one bit in the STATUS register to determine if either

accumulator has overflowed, or one bit to determine if

either accumulator has saturated. This would be useful

for complex number arithmetic which typically uses

both the accumulators.

The device supports three Saturation and Overflow

modes:

• Bit 39 Overflow and Saturation:

When bit 39 overflow and saturation occurs, the

saturation logic loads the maximally positive 9.31

(0x7FFFFFFFFF), or maximally negative 9.31

value (0x8000000000), into the target accumulator.

The SA or SB bit is set and remains set until

cleared by the user. This is referred to as ‘super

saturation’ and provides protection against errone-

ous data or unexpected algorithm problems (e.g.,

gain calculations).

• Bit 31 Overflow and Saturation:

When bit 31 overflow and saturation occurs, the

saturation logic then loads the maximally positive

1.31 value (0x007FFFFFFF), or maximally nega-

tive 1.31 value (0x0080000000), into the target

accumulator. The SA or SB bit is set and remains

set until cleared by the user. When this Saturation

mode is in effect, the guard bits are not used (so

the OA, OB or OAB bits are never set).

• Bit 39 Catastrophic Overflow:

The bit 39 Overflow Status bit from the adder is

used to set the SA or SB bit, which remains set

until cleared by the user. No saturation operation

is performed and the accumulator is allowed to

overflow (destroying its sign). If the COVTE bit in

the INTCON1 register is set, a catastrophic over-

flow can initiate a trap exception.

3.6.2.2 Accumulator ‘Write Back’

The MAC class of instructions (with the exception of

MPY, MPY.N, ED and EDAC) can optionally write a

rounded version of the high word (bits 31 through 16)

of the accumulator that is not targeted by the instruction

into data space memory. The write is performed across

the X bus into combined X and Y address space. The

following addressing modes are supported:

• W13, Register Direct:

The rounded contents of the non-target

accumulator are written into W13 as a

1.15 fraction.

• [W13]+ = 2, Register Indirect with Post-Increment:

The rounded contents of the non-target

accumulator are written into the address pointed

to by W13 as a 1.15 fraction. W13 is then

incremented by 2 (for a word write).

3.6.2.3 Round Logic

The round logic is a combinational block which

performs a conventional (biased) or convergent

(unbiased) round function during an accumulator write

(store). The Round mode is determined by the state of

the RND bit in the CORCON register. It generates a

16-bit, 1.15 data value which is passed to the data

space write saturation logic. If rounding is not indicated

by the instruction, a truncated 1.15 data value is stored

and the least significant word is simply discarded.

Conventional rounding zero-extends bit 15 of the

accumulator and adds it to the ACCxH word (bits 16

through 31 of the accumulator). If the ACCxL word

(bits 0 through 15 of the accumulator) is between

0x8000 and 0xFFFF (0x8000 included), ACCxH is

incremented. If ACCxL is between 0x0000 and 0x7FFF,

ACCxH is left unchanged. A consequence of this

algorithm is that over a succession of random rounding

operations, the value tends to be biased slightly

positive.

Convergent (or unbiased) rounding operates in the

same manner as conventional rounding, except when

ACCxL equals 0x8000. In this case, the Least

Significant bit (bit 16 of the accumulator) of ACCxH is

examined. If it is ‘1’, ACCxH is incremented. If it is ‘0’,

ACCxH is not modified. Assuming that bit 16 is

effectively random in nature, this scheme removes any

rounding bias that may accumulate.

The SAC and SAC.R instructions store either a

truncated (SAC), or rounded (SAC.R) version of the

contents of the target accumulator to data memory via

the X bus, subject to data saturation (see

Section 3.6.2.4 “Data Space Write Saturation”). For

the MAC class of instructions, the accumulator

write-back operation will function in the same manner,

addressing combined MCU (X and Y) data space

though the X bus. For this class of instructions, the data

is always subject to rounding.

dsPIC33FJXXXGPX06A/X08A/X10A

3.6.2.4 Data Space Write Saturation

In addition to adder/subtracter saturation, writes to data

space can also be saturated but without affecting the

contents of the source accumulator. The data space

write saturation logic block accepts a 16-bit, 1.15

fractional value from the round logic block as its input,

together with overflow status from the original source

(accumulator) and the 16-bit round adder. These inputs

are combined and used to select the appropriate 1.15

fractional value as output to write to data space

memory.

If the SATDW bit in the CORCON register is set, data

(after rounding or truncation) is tested for overflow and

adjusted accordingly, For input data greater than

0x007FFF, data written to memory is forced to the

maximum positive 1.15 value, 0x7FFF. For input data

less than 0xFF8000, data written to memory is forced

to the maximum negative 1.15 value, 0x8000. The

Most Significant bit of the source (bit 39) is used to

determine the sign of the operand being tested.

If the SATDW bit in the CORCON register is not set, the

input data is always passed through unmodified under

all conditions.

3.6.3 BARREL SHIFTER

The barrel shifter is capable of performing up to 16-bit

arithmetic or logic right shifts, or up to 16-bit left shifts

in a single cycle. The source can be either of the two

DSP accumulators or the X bus (to support multi-bit

shifts of register or memory data).

The shifter requires a signed binary value to determine

both the magnitude (number of bits) and direction of the

shift operation. A positive value shifts the operand right.

A negative value shifts the operand left. A value of ‘0’

does not modify the operand.

The barrel shifter is 40 bits wide, thereby obtaining a

40-bit result for DSP shift operations and a 16-bit result

for MCU shift operations. Data from the X bus is

presented to the barrel shifter between bit positions 16

to 31 for right shifts, and between bit positions 0 to 16

for left shifts.

dsPIC33FJXXXGPX06A/X08A/X10A

NOTES:

dsPIC33FJXXXGPX06A/X08A/X10A

4.0 MEMORY ORGANIZATION

The dsPIC33FJXXXGPX06A/X08A/X10A architecture

features separate program and data memory spaces

and buses. This architecture also allows the direct

access of program memory from the data space during

code execution.

4.1 Program Address Space

The program address memory space of the

dsPIC33FJXXXGPX06A/X08A/X10A devices is 4M

instructions. The space is addressable by a 24-bit

value derived from either the 23-bit Program Counter

(PC) during program execution, or from table operation

or data space remapping as described in Section 4.6

“Interfacing Program and Data Memory Spaces”.

User access to the program memory space is restricted

to the lower half of the address range (0x000000 to

0x7FFFFF). The exception is the use of TBLRD/TBLWT

operations, which use TBLPAG<7> to permit access to

the Configuration bits and Device ID sections of the

configuration memory space. Memory usage for the

dsPIC33FJXXXGPX06A/X08A/X10A of devices is

shown in Figure 4-1.

FIGURE 4-1: PROGRAM MEMORY FOR dsPIC33FJXXXGPX06A/X08A/X10A DEVICES

Note: This data sheet summarizes the features

of the dsPIC33FJXXXGPX06A/X08A/

X10A family of devices. However, it is not

intended to be a comprehensive refer-

ence source. To complement the informa-

tion in this data sheet, refer to Section 3.

“Data Memory” (DS70202) and Section

4. “Program Memory” (DS70203) in the

“dsPIC33F/PIC24H Family Reference

Manual”, which are available from the

Microchip web site (www.microchip.com).

Reset Address

0x000000

0x0000FE

0x000002

0x000100

Device Configuration

User Program

Flash Memory

0x00AC00

0x00ABFE

(22K instructions)

0x800000

0xF80000

Registers 0xF80017

0xF80010

DEVID (2)

0xFEFFFE

0xFF0000

0xFFFFFE

0xF7FFFE

Unimplemented

(Read ‘0’s)

GOTO Instruction

0x000004

Reserved

0x7FFFFE

Reserved

0x000200

0x0001FE

0x000104

Alternate Vector Table

Reserved

Interrupt Vector Table

Reset Address

Device Configuration

Registers

DEVID (2)

Unimplemented

(Read ‘0’s)

GOTO

Instruction

Reserved

Alternate Vector Table

Reserved

Interrupt Vector Table

Reset Address

Device Configuration

User Program

Flash Memory

(88K instructions)

Registers

DEVID (2)

GOTO Instruction

Reserved

Alternate Vector Table

Reserved

Interrupt Vector Table

dsPIC33FJ64GPXXXA dsPIC33FJ128GPXXXA dsPIC33FJ256GPXXXA

Configuration Memory Space User Memory Space

0x015800

0x0157FE

Note: Memory areas are not shown to scale.

User Program

(44K instructions)

Flash Memory

(Read ‘0’s)

Unimplemented

0x02AC00

0x02ABFE

dsPIC33FJXXXGPX06A/X08A/X10A

4.1.1 PROGRAM MEMORY

ORGANIZATION

The program memory space is organized in

word-addressable blocks. Although it is treated as

24 bits wide, it is more appropriate to think of each

address of the program memory as a lower and upper

word, with the upper byte of the upper word being

unimplemented. The lower word always has an even

address, while the upper word has an odd address

(Figure 4-2).

Program memory addresses are always word-aligned

on the lower word, and addresses are incremented or

decremented by two during code execution. This

arrangement also provides compatibility with data

memory space addressing and makes it possible to

access data in the program memory space.

4.1.2 INTERRUPT AND TRAP VECTORS

All dsPIC33FJXXXGPX06A/X08A/X10A devices

reserve the addresses between 0x00000 and

0x000200 for hard-coded program execution vectors.

A hardware Reset vector is provided to redirect code

execution from the default value of the PC on device

Reset to the actual start of code. A GOTO instruction is

programmed by the user at 0x000000, with the actual

address for the start of code at 0x000002.

dsPIC33FJXXXGPX06A/X08A/X10A devices also

have two interrupt vector tables, located from

0x000004 to 0x0000FF and 0x000100 to 0x0001FF.

These vector tables allow each of the many device

interrupt sources to be handled by separate Interrupt

Service Routines (ISRs). A more detailed discussion of

the interrupt vector tables is provided in Section 7.1

“Interrupt Vector Table”.

FIGURE 4-2: PROGRAM MEMORY ORGANIZATION

0816

PC Address

0x000000

0x000002

0x000004

0x000006

00000000

Program Memory

‘Phantom’ Byte

(read as ‘0’)

least significant word

most significant word

Instruction Width

0x000001

0x000003

0x000005

0x000007

msw

Address (lsw Address)

dsPIC33FJXXXGPX06A/X08A/X10A

4.2 Data Address Space

The dsPIC33FJXXXGPX06A/X08A/X10A CPU has a

separate 16-bit wide data memory space. The data

space is accessed using separate Address Generation

Units (AGUs) for read and write operations. Data

memory maps of devices with different RAM sizes are

shown in Figure 4-3 through Figure 4-5.

All Effective Addresses (EAs) in the data memory space

are 16 bits wide and point to bytes within the data space.

This arrangement gives a data space address range of

64 Kbytes or 32K words. The lower half of the data

memory space (that is, when EA<15> = 0) is used for

implemented memory addresses, while the upper half

(EA<15> = 1) is reserved for the Program Space

Visibility area (see Section 4.6.3 “Reading Data from

Program Memory Using Program Space Visibility”).

dsPIC33FJXXXGPX06A/X08A/X10A devices imple-

ment a total of up to 30 Kbytes of data memory. Should

an EA point to a location outside of this area, an all-zero

word or byte will be returned.

4.2.1 DATA SPACE WIDTH

The data memory space is organized in byte

addressable, 16-bit wide blocks. Data is aligned in data

memory and registers as 16-bit words, but all data

space EAs resolve to bytes. The Least Significant

Bytes (LSBs) of each word have even addresses, while

the Most Significant Bytes (MSBs) have odd

addresses.

4.2.2 DATA MEMORY ORGANIZATION

AND ALIGNMENT

To maintain backward compatibility with PIC® MCU

devices and improve data space memory usage

efficiency, the dsPIC33FJXXXGPX06A/X08A/X10A

instruction set supports both word and byte operations.

As a consequence of byte accessibility, all effective

address calculations are internally scaled to step

through word-aligned memory. For example, the core

recognizes that Post-Modified Register Indirect

Addressing mode [Ws++] will result in a value of Ws + 1

for byte operations and Ws + 2 for word operations.

Data byte reads will read the complete word that

contains the byte, using the LSb of any EA to determine

which byte to select. The selected byte is placed onto

the LSb of the data path. That is, data memory and

registers are organized as two parallel byte-wide

entities with shared (word) address decode but

separate write lines. Data byte writes only write to the

corresponding side of the array or register which

matches the byte address.

All word accesses must be aligned to an even address.

Misaligned word data fetches are not supported, so

care must be taken when mixing byte and word

operations, or translating from 8-bit MCU code. If a

misaligned read or write is attempted, an address error

trap is generated. If the error occurred on a read, the

instruction underway is completed; if it occurred on a

write, the instruction will be executed but the write does

not occur. In either case, a trap is then executed,

allowing the system and/or user to examine the

machine state prior to execution of the address Fault.

All byte loads into any W register are loaded into the

Least Significant Byte. The Most Significant Byte is not

modified.

A sign-extend instruction (SE) is provided to allow

users to translate 8-bit signed data to 16-bit signed

values. Alternatively, for 16-bit unsigned data, users

can clear the MSb of any W register by executing a

zero-extend (ZE) instruction on the appropriate

address.

4.2.3 SFR SPACE

The first 2 Kbytes of the Near Data Space, from 0x0000

to 0x07FF, is primarily occupied by Special Function

Registers (SFRs). These are used by the

dsPIC33FJXXXGPX06A/X08A/X10A core and periph-

eral modules for controlling the operation of the device.

SFRs are distributed among the modules that they

control, and are generally grouped together by module.

Much of the SFR space contains unused addresses;

these are read as ‘0’. A complete listing of implemented

SFRs, including their addresses, is shown in Table 4-1

through Ta b l e 4 - 3 4 .

4.2.4 NEAR DATA SPACE

The 8-Kbyte area between 0x0000 and 0x1FFF is

referred to as the Near Data Space. Locations in this

space are directly addressable via a 13-bit absolute

address field within all memory direct instructions.

Additionally, the whole data space is addressable using

MOV instructions, which support Memory Direct

Addressing mode with a 16-bit address field, or by

using Indirect Addressing mode using a working

Note: The actual set of peripheral features and

interrupts varies by the device. Please

refer to the corresponding device tables

and pinout diagrams for device-specific

information.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 4-3: DATA MEMORY MAP FOR dsPIC33FJXXXGPX06A/X08A/X10A DEVICES WITH 8

KBS RAM

0x0000

0x07FE

0x17FE

0xFFFE

LSB

Address

16 bits

LSBMSB

MSB

Address

0x0001

0x07FF

0x17FF

0xFFFF

Optionally

Mapped

into Program

Memory

0x27FF 0x27FE

0x0801 0x0800

0x1801 0x1800

2 Kbyte

SFR Space

8 Kbyte

SRAM Space

0x8001 0x8000

0x28000x2801

0x1FFE

0x2000

0x1FFF

0x2001

Space

Data

Near

8 Kbyte

SFR Space

X Data RAM (X)

X Data

Unimplemented (X)

DMA RAM

Y Data RAM (Y)

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 4-4: DATA MEMORY MAP FOR dsPIC33FJXXXGPX06A/X08A/X10A DEVICES WITH

16 KBS RAM

0x0000

0x07FE

0x27FE

0xFFFE

LSB

Address

16 bits

LSBMSB

MSB

Address

0x0001

0x07FF

0x27FF

0xFFFF

Optionally

Mapped

into Program

Memory

0x47FF 0x47FE

0x0801 0x0800

0x2801 0x2800

Near

Data

2 Kbyte

SFR Space

16 Kbyte

SRAM Space

8 Kbyte

Space

0x8001 0x8000

0x48000x4801

0x3FFE

0x4000

0x3FFF

0x4001

0x1FFE

0x1FFF

SFR Space

X Data RAM (X)

X Data

Unimplemented (X)

DMA RAM

Y Data RAM (Y)

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 4-5: DATA MEMORY MAP FOR dsPIC33FJXXXGPX06A/X08A/X10A DEVICES WITH

30 KBS RAM

0x0000

0x07FE

SFR Space

0xFFFE

X Data RAM (X)

16 bits

LSBMSB

0x0001

0x07FF

0xFFFF

X Data

Optionally

Mapped

into Program

Memory

Unimplemented (X)

0x0801 0x0800

2 Kbyte

SFR Space

0x4800

0x47FE

0x4801

0x47FF

0x7FFE

0x8000

30 Kbyte

SRAM Space

0x7FFF

0x8001

Y Data RAM (Y)

Near

Data

8 Kbyte

Space

0x77FE

0x7800

0x77FF

0x7800

LSB

Address

MSB

Address

DMA RAM

dsPIC33FJXXXGPX06A/X08A/X10A

4.2.5 X AND Y DATA SPACES

The core has two data spaces, X and Y. These data

spaces can be considered either separate (for some

DSP instructions), or as one unified linear address

range (for MCU instructions). The data spaces are

accessed using two Address Generation Units (AGUs)

and separate data paths. This feature allows certain

instructions to concurrently fetch two words from RAM,

thereby enabling efficient execution of DSP algorithms

such as Finite Impulse Response (FIR) filtering and

Fast Fourier Transform (FFT).

The X data space is used by all instructions and

supports all addressing modes. There are separate

read and write data buses for X data space. The X read

data bus is the read data path for all instructions that

view data space as combined X and Y address space.

It is also the X data prefetch path for the dual operand

DSP instructions (MAC class).

The Y data space is used in concert with the X data

space by the MAC class of instructions (CLR, ED,

EDAC, MAC, MOVSAC, MPY, MPY.N and MSC) to provide

two concurrent data read paths.

Both the X and Y data spaces support Modulo

Addressing mode for all instructions, subject to

addressing mode restrictions. Bit-Reversed Addressing

mode is only supported for writes to X data space.

All data memory writes, including in DSP instructions,

view data space as combined X and Y address space.

The boundary between the X and Y data spaces is

device-dependent and is not user-programmable.

All effective addresses are 16 bits wide and point to

bytes within the data space. Therefore, the data space

address range is 64 Kbytes, or 32K words, though the

implemented memory locations vary by device.

4.2.6 DMA RAM

Every dsPIC33FJXXXGPX06A/X08A/X10A device

contains 2 Kbytes of dual ported DMA RAM located at

the end of Y data space. Memory locations is part of Y

data RAM and is in the DMA RAM space are accessible

simultaneously by the CPU and the DMA controller

module. DMA RAM is utilized by the DMA controller to

store data to be transferred to various peripherals using

DMA, as well as data transferred from various

peripherals using DMA. The DMA RAM can be

accessed by the DMA controller without having to steal

cycles from the CPU.

When the CPU and the DMA controller attempt to

concurrently write to the same DMA RAM location, the

hardware ensures that the CPU is given precedence in

accessing the DMA RAM location. Therefore, the DMA

RAM provides a reliable means of transferring DMA

data without ever having to stall the CPU.

Note: DMA RAM can be used for general

purpose data storage if the DMA function

is not required in an application.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 4-1: CPU CORE REGISTERS MAP

SFR Name SFR

Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

WREG0 0000 Working Register 0

xxxx

WREG1 0002 Working Register 1

xxxx

WREG2 0004 Working Register 2

xxxx

WREG3 0006 Working Register 3

xxxx

WREG4 0008 Working Register 4

xxxx

WREG5 000A Working Register 5

xxxx

WREG6 000C Working Register 6

xxxx

WREG7 000E Working Register 7

xxxx

WREG8 0010 Working Register 8

xxxx

WREG9 0012 Working Register 9

xxxx

WREG10 0014 Working Register 10

xxxx

WREG11 0016 Working Register 11

xxxx

WREG12 0018 Working Register 12

xxxx

WREG13 001A Working Register 13

xxxx

WREG14 001C Working Register 14

xxxx

WREG15 001E Working Register 15

0800

SPLIM 0020 Stack Pointer Limit Register

xxxx

ACCAL 0022 Accumulator A Low Word Register

0000

ACCAH 0024 Accumulator A High Word Register

0000

ACCAU 0026 Accumulator A Upper Word Register

0000

ACCBL 0028 Accumulator B Low Word Register

0000

ACCBH 002A Accumulator B High Word Register

0000

ACCBU 002C Accumulator B Upper Word Register

0000

PCL 002E Program Counter Low Word Register

0000

PCH 0030 — — — — — — — — Program Counter High Byte Register

0000

TBLPAG 0032 — — — — — — — — Table Page Address Pointer Register

0000

PSVPAG 0034 — — — — — — — — Program Memory Visibility Page Address Pointer Register

0000

RCOUNT 0036 Repeat Loop Counter Register

xxxx

DCOUNT 0038 DCOUNT<15:0> xxxx

DOSTARTL 003A DOSTARTL<15:1> 0 xxxx

DOSTARTH 003C

— — — — — — — — — —

DOSTARTH<5:0> 00xx

DOENDL 003E DOENDL<15:1> 0 xxxx

DOENDH 0040

— — — — — — — — — —

DOENDH 00xx

SR 0042 OA OB SA SB OAB SAB DA DC IPL2 IPL1 IPL0 RA N OV Z C

0000

CORCON 0044 — — —USEDT DL<2:0>

SATA SATB SATDW ACCSAT IPL3 PSV RND IF

0020

MODCON 0046 XMODEN YMODEN

— —

BWM<3:0> YWM<3:0> XWM<3:0> 0000

XMODSRT 0048 XS<15:1> 0 xxxx

XMODEND 004A XE<15:1> 1 xxxx

YMODSRT 004C YS<15:1> 0 xxxx

YMODEND 004E YE<15:1> 1 xxxx

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33FJXXXGPX06A/X08A/X10A

XBREV 0050 BREN XB<14:0> xxxx

DISICNT 0052 —

— Disable Interrupts Counter

xxxx

BSRAM 0750

— — — — — — — — — — — — —

IW_BSR IR_BSR RL_BSR

0000

SSRAM 0752

— — — — — — — — — — — — —

IW_SSR IR_SSR RL_SSR

0000

TABLE 4-1: CPU CORE REGISTERS MAP (CONTINUED)

SFR Name SFR

Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 4-2: CHANGE NOTIFICATION REGISTER MAP FOR dsPIC33FJXXXGPX10A DEVICES

SFR

Name SFR

Addr Bit 15Bit 14Bit 13Bit 12Bit 11Bit 10Bit 9Bit 8Bit 7Bit 6Bit 5Bit 4Bit 3Bit 2Bit 1Bit 0All

Resets

CNEN1 0060 CN15IE CN14IE CN13IE CN12IE CN11IE CN10IE CN9IE CN8IE CN7IE CN6IE CN5IE CN4IE CN3IE CN2IE CN1IE CN0IE

0000

CNEN2 0062

————————

CN23IE CN22IE CN21IE CN20IE CN19IE CN18IE CN17IE CN16IE

0000

CNPU1 0068 CN15PUE CN14PUE CN13PUE CN12PUE CN11PUE CN10PUE CN9PUE CN8PUE CN7PUE CN6PUE CN5PUE CN4PUE CN3PUE CN2PUE CN1PUE CN0PUE

0000

CNPU2 006A

————————

CN23PUE CN22PUE CN21PUE CN20PUE CN19PUE CN18PUE CN17PUE CN16PUE

0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

TABLE 4-3: CHANGE NOTIFICATION REGISTER MAP FOR dsPIC33FJXXXGPX08A DEVICES

SFR

Name SFR

Addr Bit 15Bit 14Bit 13Bit 12Bit 11Bit 10Bit 9Bit 8Bit 7Bit 6Bit 5Bit 4Bit 3Bit 2Bit 1Bit 0All

Resets

CNEN1 0060 CN15IE CN14IE CN13IE CN12IE CN11IE CN10IE CN9IE CN8IE CN7IE CN6IE CN5IE CN4IE CN3IE CN2IE CN1IE CN0IE

0000

CNEN2 0062

——————————

CN21IE CN20IE CN19IE CN18IE CN17IE CN16IE

0000

CNPU1 0068 CN15PUE CN14PUE CN13PUE CN12PUE CN11PUE CN10PUE CN9PUE CN8PUE CN7PUE CN6PUE CN5PUE CN4PUE CN3PUE CN2PUE CN1PUE CN0PUE

0000

CNPU2 006A

——————————

CN21PUE CN20PUE CN19PUE CN18PUE CN17PUE CN16PUE

0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

TABLE 4-4: CHANGE NOTIFICATION REGISTER MAP FOR dsPIC33FJXXXGPX06A DEVICES

SFR

Name SFR

Addr Bit 15Bit 14Bit 13Bit 12Bit 11Bit 10Bit 9Bit 8Bit 7Bit 6Bit 5Bit 4Bit 3Bit 2Bit 1Bit 0All

Resets

CNEN1 0060 CN15IE CN14IE CN13IE CN12IE CN11IE CN10IE CN9IE CN8IE CN7IE CN6IE CN5IE CN4IE CN3IE CN2IE CN1IE CN0IE

0000

CNEN2 0062

——————————

CN21IE CN20IE — CN18IE CN17IE CN16IE

0000

CNPU1 0068 CN15PUE CN14PUE CN13PUE CN12PUE CN11PUE CN10PUE CN9PUE CN8PUE CN7PUE CN6PUE CN5PUE CN4PUE CN3PUE CN2PUE CN1PUE CN0PUE

0000

CNPU2 006A

——————————

CN21PUE CN20PUE — CN18PUE CN17PUE CN16PUE

0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 4-5: INTERRUPT CONTROLLER REGISTER MAP

SFR

Name

SFR

Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

INTCON1 0080 NSTDIS OVAERR OVBERR COVAERR COVBERR OVATE OVBTE COVTE SFTACERR DIV0ERR DMACERR MATHERR ADDRERR STKERR OSCFAIL —0000

INTCON2 0082 ALTIVT DISI — — — — — — — — — INT4EP INT3EP INT2EP INT1EP INT0EP 0000

IFS0 0084 — DMA1IF AD1IF U1TXIF U1RXIF SPI1IF SPI1EIF T3IF T2IF OC2IF IC2IF DMA0IF T1IF OC1IF IC1IF INT0IF 0000

IFS1 0086 U2TXIF U2RXIF INT2IF T5IF T4IF OC4IF OC3IF DMA2IF IC8IF IC7IF AD2IF INT1IF CNIF — MI2C1IF SI2C1IF 0000

IFS2 0088 T6IF DMA4IF — OC8IF OC7IF OC6IF OC5IF IC6IF IC5IF IC4IF IC3IF DMA3IF C1IF C1RXIF SPI2IF SPI2EIF 0000

IFS3 008A —— DMA5IF DCIIF DCIEIF —— C2IF C2RXIF INT4IF INT3IF T9IF T8IF MI2C2IF SI2C2IF T7IF 0000

IFS4 008C — — — — — — — — C2TXIF C1TXIF DMA7IF DMA6IF —U2EIFU1EIF—0000

IEC0 0094 — DMA1IE AD1IE U1TXIE U1RXIE SPI1IE SPI1EIE T3IE T2IE OC2IE IC2IE DMA0IE T1IE OC1IE IC1IE INT0IE 0000

IEC1 0096 U2TXIE U2RXIE INT2IE T5IE T4IE OC4IE OC3IE DMA2IE IC8IE IC7IE AD2IE INT1IE CNIE — MI2C1IE SI2C1IE 0000

IEC2 0098 T6IE DMA4IE — OC8IE OC7IE OC6IE OC5IE IC6IE IC5IE IC4IE IC3IE DMA3IE C1IE C1RXIE SPI2IE SPI2EIE 0000

IEC3 009A —— DMA5IE DCIIE DCIEIE —— C2IE C2RXIE INT4IE INT3IE T9IE T8IE MI2C2IE SI2C2IE T7IE 0000

IEC4 009C — — — — — — — — C2TXIE C1TXIE DMA7IE DMA6IE —U2EIEU1EIE—0000

IPC0 00A4 — T1IP<2:0> — OC1IP<2:0> —IC1IP<2:0>— INT0IP<2:0> 4444

IPC1 00A6 — T2IP<2:0> — OC2IP<2:0> —IC2IP<2:0>— DMA0IP<2:0> 4444

IPC2 00A8 — U1RXIP<2:0> — SPI1IP<2:0> — SPI1EIP<2:0> — T3IP<2:0> 4444

IPC3 00AA — — — — — DMA1IP<2:0> — AD1IP<2:0> — U1TXIP<2:0> 0444

IPC4 00AC — CNIP<2:0> — — — — — MI2C1IP<2:0> — SI2C1IP<2:0> 4044

IPC5 00AE — IC8IP<2:0> —IC7IP<2:0>— AD2IP<2:0> — INT1IP<2:0> 4444

IPC6 00B0 — T4IP<2:0> — OC4IP<2:0> — OC3IP<2:0> — DMA2IP<2:0> 4444

IPC7 00B2 — U2TXIP<2:0> — U2RXIP<2:0> — INT2IP<2:0> — T5IP<2:0> 4444

IPC8 00B4 — C1IP<2:0> — C1RXIP<2:0> — SPI2IP<2:0> — SPI2EIP<2:0> 4444

IPC9 00B6 — IC5IP<2:0> —IC4IP<2:0> —IC3IP<2:0>— DMA3IP<2:0> 4444

IPC10 00B8 —OC7IP<2:0> — OC6IP<2:0> — OC5IP<2:0> — IC6IP<2:0> 4444

IPC11 00BA — T6IP<2:0> — DMA4IP<2:0> — — — — —OC8IP<2:0>4404

IPC12 00BC — T8IP<2:0> —MI2C2IP<2:0>— SI2C2IP<2:0> — T7IP<2:0> 4444

IPC13 00BE — C2RXIP<2:0> — INT4IP<2:0> — INT3IP<2:0> — T9IP<2:0> 4444

IPC14 00C0 — DCIEIP<2:0> — — — — — — — — — C2IP<2:0> 4004

IPC15 00C2 — — — — — — — — — DMA5IP<2:0> — DCIIP<2:0> 0044

IPC16 00C4 — — — — — U2EIP<2:0> — U1EIP<2:0> — — — — 0440

IPC17 00C6 — C2TXIP<2:0> — C1TXIP<2:0> — DMA7IP<2:0> — DMA6IP<2:0> 4444

INTTREG 00E0 — — — —ILR<3:0> — VECNUM<6:0> 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 4-6: TIMER REGISTER MAP

SFR

Name SFR

Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TMR1 0100 Timer1 Register

0000

PR1 0102 Period Register 1

FFFF

T1CON 0104 TON

—

TSIDL

——————

TGATE TCKPS<1:0>

—

TSYNC TCS

—

0000

TMR2 0106 Timer2 Register

0000

TMR3HLD 0108 Timer3 Holding Register (for 32-bit timer operations only)

xxxx

TMR3 010A Timer3 Register

0000

PR2 010C Period Register 2

FFFF

PR3 010E Period Register 3

FFFF

T2CON 0110 TON

—

TSIDL

——————

TGATE TCKPS<1:0> T32

—

TCS

—

0000

T3CON 0112 TON

—

TSIDL

——————

TGATE TCKPS<1:0>

— —

TCS

—

0000

TMR4 0114 Timer4 Register

0000

TMR5HLD 0116 Timer5 Holding Register (for 32-bit operations only)

xxxx

TMR5 0118 Timer5 Register

0000

PR4 011A Period Register 4

FFFF

PR5 011C Period Register 5

FFFF

T4CON 011E TON

—

TSIDL

——————

TGATE TCKPS<1:0> T32

—

TCS

—

0000

T5CON 0120 TON

—

TSIDL

——————

TGATE TCKPS<1:0>

— —

TCS

—

0000

TMR6 0122 Timer6 Register

0000

TMR7HLD 0124 Timer7 Holding Register (for 32-bit operations only)

xxxx

TMR7 0126 Timer7 Register

0000

PR6 0128 Period Register 6

FFFF

PR7 012A Period Register 7

FFFF

T6CON 012C TON —TSIDL—————— TGATE TCKPS<1:0> T32 —TCS

—

0000

T7CON 012E TON —TSIDL—————— TGATE TCKPS<1:0> ——TCS

—

0000

TMR8 0130 Timer8 Register

0000

TMR9HLD 0132 Timer9 Holding Register (for 32-bit operations only)

xxxx

TMR9 0134 Timer9 Register

0000

PR8 0136 Period Register 8

FFFF

PR9 0138 Period Register 9

FFFF

T8CON 013A TON

—

TSIDL

——————

TGATE TCKPS<1:0> T32

—

TCS

—

0000

T9CON 013C TON

—

TSIDL

——————

TGATE TCKPS<1:0>

— —

TCS

—

0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 4-7: INPUT CAPTURE REGISTER MAP

SFR Name SFR

Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

IC1BUF 0140 Input 1 Capture Register

xxxx

IC1CON 0142

— —

ICSIDL

— — — — —

ICTMR ICI<1:0> ICOV ICBNE ICM<2:0>

0000

IC2BUF 0144 Input 2 Capture Register

xxxx

IC2CON 0146

— —

ICSIDL

— — — — —

ICTMR ICI<1:0> ICOV ICBNE ICM<2:0>

0000

IC3BUF 0148 Input 3 Capture Register

xxxx

IC3CON 014A

— —

ICSIDL

— — — — —

ICTMR ICI<1:0> ICOV ICBNE ICM<2:0>

0000

IC4BUF 014C Input 4 Capture Register

xxxx

IC4CON 014E

— —

ICSIDL

— — — — —

ICTMR ICI<1:0> ICOV ICBNE ICM<2:0>

0000

IC5BUF 0150 Input 5 Capture Register

xxxx

IC5CON 0152

— —

ICSIDL

— — — — —

ICTMR ICI<1:0> ICOV ICBNE ICM<2:0>

0000

IC6BUF 0154 Input 6 Capture Register

xxxx

IC6CON 0156

— —

ICSIDL

— — — — —

ICTMR ICI<1:0> ICOV ICBNE ICM<2:0>

0000

IC7BUF 0158 Input 7 Capture Register

xxxx

IC7CON 015A

— —

ICSIDL

— — — — —

ICTMR ICI<1:0> ICOV ICBNE ICM<2:0>

0000

IC8BUF 015C Input 8 Capture Register

xxxx

IC8CON 015E

— —

ICSIDL

— — — — —

ICTMR ICI<1:0> ICOV ICBNE ICM<2:0>

0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 4-8: OUTPUT COMPARE REGISTER MAP

SFR Name SFR

Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

OC1RS 0180 Output Compare 1 Secondary Register

xxxx

OC1R 0182 Output Compare 1 Register

xxxx

OC1CON 0184

— —

OCSIDL

— — — — — — — —

OCFLT OCTSEL OCM<2:0>

0000

OC2RS 0186 Output Compare 2 Secondary Register

xxxx

OC2R 0188 Output Compare 2 Register

xxxx

OC2CON 018A

— —

OCSIDL

— — — — — — — —

OCFLT OCTSEL OCM<2:0>

0000

OC3RS 018C Output Compare 3 Secondary Register

xxxx

OC3R 018E Output Compare 3 Register

xxxx

OC3CON 0190

— —

OCSIDL

— — — — — — — —

OCFLT OCTSEL OCM<2:0>

0000

OC4RS 0192 Output Compare 4 Secondary Register

xxxx

OC4R 0194 Output Compare 4 Register

xxxx

OC4CON 0196

— —

OCSIDL

— — — — — — — —

OCFLT OCTSEL OCM<2:0>

0000

OC5RS 0198 Output Compare 5 Secondary Register

xxxx

OC5R 019A Output Compare 5 Register

xxxx

OC5CON 019C

— —

OCSIDL

— — — — — — — —

OCFLT OCTSEL OCM<2:0>

0000

OC6RS 019E Output Compare 6 Secondary Register

xxxx

OC6R 01A0 Output Compare 6 Register

xxxx

OC6CON 01A2

— —

OCSIDL

— — — — — — — —

OCFLT OCTSEL OCM<2:0>

0000

OC7RS 01A4 Output Compare 7 Secondary Register

xxxx

OC7R 01A6 Output Compare 7 Register

xxxx

OC7CON 01A8

— —

OCSIDL

— — — — — — — —

OCFLT OCTSEL OCM<2:0>

0000

OC8RS 01AA Output Compare 8 Secondary Register

xxxx

OC8R 01AC Output Compare 8 Register

xxxx

OC8CON 01AE

— —

OCSIDL

— — — — — — — —

OCFLT OCTSEL OCM<2:0>

0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 4-9: I2C1 REGISTER MAP

SFR Name SFR

Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

I2C1RCV 0200 — ——————— Receive Register

0000

I2C1TRN 0202 — ——————— Transmit Register

00FF

I2C1BRG 0204 — —————— Baud Rate Generator Register

0000

I2C1CON 0206 I2CEN — I2CSIDL SCLREL IPMIEN A10M DISSLW SMEN GCEN STREN ACKDT ACKEN RCEN PEN RSEN SEN

1000

I2C1STAT 0208 ACKSTAT TRSTAT ——— BCL GCSTAT ADD10 IWCOL I2COV D_A P S R_W RBF TBF

0000

I2C1ADD 020A — ————— Address Register

0000

I2C1MSK 020C — ————— Address Mask Register

0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

TABLE 4-10: I2C2 REGISTER MAP

SFR Name SFR

Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

I2C2RCV 0210 — ——————— Receive Register

0000

I2C2TRN 0212 — ——————— Transmit Register

00FF

I2C2BRG 0214 — —————— Baud Rate Generator Register

0000

I2C2CON 0216 I2CEN — I2CSIDL SCLREL IPMIEN A10M DISSLW SMEN GCEN STREN ACKDT ACKEN RCEN PEN RSEN SEN

1000

I2C2STAT 0218 ACKSTAT TRSTAT — — — BCL GCSTAT ADD10 IWCOL I2COV D_A P S R_W RBF TBF

0000

I2C2ADD 021A — ————— Address Register

0000

I2C2MSK 021C — ————— Address Mask Register

0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 4-11: UART1 REGISTER MAP

SFR Name SFR

Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

U1MODE 0220 UARTEN — USIDL IREN RTSMD — UEN1 UEN0 WAKE LPBACK ABAUD URXINV BRGH PDSEL<1:0> STSEL

0000

U1STA 0222 UTXISEL1 UTXINV UTXISEL0 — UTXBRK UTXEN UTXBF TRMT URXISEL<1:0> ADDEN RIDLE PERR FERR OERR URXDA

0110

U1TXREG 0224 — — — — — — — UART Transmit Register

xxxx

U1RXREG 0226 — — — — — — — UART Receive Register

0000

U1BRG 0228 Baud Rate Generator Prescaler

0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

TABLE 4-12: UART2 REGISTER MAP

SFR

Name

SFR

Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

U2MODE 0230 UARTEN — USIDL IREN RTSMD — UEN1 UEN0 WAKE LPBACK ABAUD URXINV BRGH PDSEL<1:0> STSEL

0000

U2STA 0232 UTXISEL1 UTXINV UTXISEL0 — UTXBRK UTXEN UTXBF TRMT URXISEL<1:0> ADDEN RIDLE PERR FERR OERR URXDA

0110

U2TXREG 0234 — — — — — — — UART Transmit Register

xxxx

U2RXREG 0236 — — — — — — — UART Receive Register

0000

U2BRG 0238 Baud Rate Generator Prescaler

0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

TABLE 4-13: SPI1 REGISTER MAP

SFR

Name

SFR

Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

SPI1STAT 0240 SPIEN — SPISIDL ——————SPIROV———— SPITBF SPIRBF

0000

SPI1CON1 0242 — — — DISSCK DISSDO MODE16 SMP CKE SSEN CKP MSTEN SPRE<2:0> PPRE<1:0>

0000

SPI1CON2 0244 FRMEN SPIFSD FRMPOL ——————————— FRMDLY —

0000

SPI1BUF 0248 SPI1 Transmit and Receive Buffer Register

0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

TABLE 4-14: SPI2 REGISTER MAP

SFR Name SFR

Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

SPI2STAT 0260 SPIEN —SPISIDL—————— SPIROV ———— SPITBF SPIRBF

0000

SPI2CON1 0262 — — — DISSCK DISSDO MODE16 SMP CKE SSEN CKP MSTEN SPRE<2:0> PPRE<1:0>

0000

SPI2CON2 0264 FRMEN SPIFSD FRMPOL ——————————— FRMDLY —

0000

SPI2BUF 0268 SPI2 Transmit and Receive Buffer Register

0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 4-15: ADC1 REGISTER MAP

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

ADC1BUF0 0300 ADC Data Buffer 0 xxxx

AD1CON1 0320 ADON — ADSIDL ADDMABM — AD12B FORM<1:0> SSRC<2:0> — SIMSAM ASAM SAMP DONE 0000

AD1CON2 0322 VCFG<2:0> —— CSCNA CHPS<1:0> BUFS — SMPI<3:0> BUFM ALTS 0000

AD1CON3 0324 ADRC —— SAMC<4:0> ADCS<7:0> 0000

AD1CHS123 0326 — — — — — CH123NB<1:0> CH123SB — — — — — CH123NA<1:0> CH123SA 0000

AD1CHS0 0328 CH0NB —— CH0SB<4:0> CH0NA —— CH0SA<4:0> 0000

AD1PCFGH(1) 032A PCFG31 PCFG30 PCFG29 PCFG28 PCFG27 PCFG26 PCFG25 PCFG24 PCFG23 PCFG22 PCFG21 PCFG20 PCFG19 PCFG18 PCFG17 PCFG16 0000

AD1PCFGL 032C PCFG15 PCFG14 PCFG13 PCFG12 PCFG11 PCFG10 PCFG9 PCFG8 PCFG7 PCFG6 PCFG5 PCFG4 PCFG3 PCFG2 PCFG1 PCFG0 0000

AD1CSSH(1) 032E CSS31 CSS30 CSS29 CSS28 CSS27 CSS26 CSS25 CSS24 CSS23 CSS22 CSS21 CSS20 CSS19 CSS18 CSS17 CSS16 0000

AD1CSSL 0330 CSS15 CSS14 CSS13 CSS12 CSS11 CSS10 CSS9 CSS8 CSS7 CSS6 CSS5 CSS4 CSS3 CSS2 CSS1 CSS0 0000

AD1CON4 0332 — — — — — — — — — — — — — DMABL<2:0> 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

Note 1: Not all ANx inputs are available on all devices. See the device pin diagrams for available ANx inputs.

TABLE 4-16: ADC2 REGISTER MAP

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

ADC2BUF0 0340 ADC Data Buffer 0 xxxx

AD2CON1 0360 ADON — ADSIDL ADDMABM — AD12B FORM<1:0> SSRC<2:0> — SIMSAM ASAM SAMP DONE 0000

AD2CON2 0362 VCFG<2:0> —— CSCNA CHPS<1:0> BUFS — SMPI<3:0> BUFM ALTS 0000

AD2CON3 0364 ADRC —— SAMC<4:0> ADCS<7:0> 0000

AD2CHS123 0366 — — — — — CH123NB<1:0> CH123SB — — — — — CH123NA<1:0> CH123SA 0000

AD2CHS0 0368 CH0NB — — — CH0SB<3:0> CH0NA — — — CH0SA<3:0> 0000

Reserved 036A — — — — — — — — — — — — — — — — 0000

AD2PCFGL 036C PCFG15 PCFG14 PCFG13 PCFG12 PCFG11 PCFG10 PCFG9 PCFG8 PCFG7 PCFG6 PCFG5 PCFG4 PCFG3 PCFG2 PCFG1 PCFG0 0000

Reserved 036E — — — — — — — — — — — — — — — — 0000

AD2CSSL 0370 CSS15 CSS14 CSS13 CSS12 CSS11 CSS10 CSS9 CSS8 CSS7 CSS6 CSS5 CSS4 CSS3 CSS2 CSS1 CSS0 0000

AD2CON4 0372 — — — — — — — — — — — — —DMABL<2:0>0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 4-17: DMA REGISTER MAP

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

DMA0CON 0380 CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0> ——MODE<1:0>0000

DMA0REQ 0382 FORCE — — — — — — — — IRQSEL<6:0> 0000

DMA0STA 0384 STA<15:0> 0000

DMA0STB 0386 STB<15:0> 0000

DMA0PAD 0388 PAD<15:0> 0000

DMA0CNT 038A — — — — — — CNT<9:0> 0000

DMA1CON 038C CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0> ——MODE<1:0>0000

DMA1REQ 038E FORCE — — — — — — — — IRQSEL<6:0> 0000

DMA1STA 0390 STA<15:0> 0000

DMA1STB 0392 STB<15:0> 0000

DMA1PAD 0394 PAD<15:0> 0000

DMA1CNT 0396 — — — — — — CNT<9:0> 0000

DMA2CON 0398 CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0> ——MODE<1:0>0000

DMA2REQ 039A FORCE — — — — — — — — IRQSEL<6:0> 0000

DMA2STA 039C STA<15:0> 0000

DMA2STB 039E STB<15:0> 0000

DMA2PAD 03A0 PAD<15:0> 0000

DMA2CNT 03A2 — — — — — — CNT<9:0> 0000

DMA3CON 03A4 CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0> ——MODE<1:0>0000

DMA3REQ 03A6 FORCE — — — — — — — — IRQSEL<6:0> 0000

DMA3STA 03A8 STA<15:0> 0000

DMA3STB 03AA STB<15:0> 0000

DMA3PAD 03AC PAD<15:0> 0000

DMA3CNT 03AE — — — — — — CNT<9:0> 0000

DMA4CON 03B0 CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0> ——MODE<1:0>0000

DMA4REQ 03B2 FORCE — — — — — — — — IRQSEL<6:0> 0000

DMA4STA 03B4 STA<15:0> 0000

DMA4STB 03B6 STB<15:0> 0000

DMA4PAD 03B8 PAD<15:0> 0000

DMA4CNT 03BA — — — — — — CNT<9:0> 0000

DMA5CON 03BC CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0> ——MODE<1:0>0000

DMA5REQ 03BE FORCE — — — — — — — — IRQSEL<6:0> 0000

DMA5STA 03C0 STA<15:0> 0000

DMA5STB 03C2 STB<15:0> 0000

DMA5PAD 03C4 PAD<15:0> 0000

Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33FJXXXGPX06A/X08A/X10A

DMA5CNT 03C6 — — — — — — CNT<9:0> 0000

DMA6CON 03C8 CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0> ——MODE<1:0>0000

DMA6REQ 03CA FORCE — — — — — — — — IRQSEL<6:0> 0000

DMA6STA 03CC STA<15:0> 0000

DMA6STB 03CE STB<15:0> 0000

DMA6PAD 03D0 PAD<15:0> 0000

DMA6CNT 03D2 — — — — — — CNT<9:0> 0000

DMA7CON 03D4 CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0> ——MODE<1:0>0000

DMA7REQ 03D6 FORCE — — — — — — — — IRQSEL<6:0> 0000

DMA7STA 03D8 STA<15:0> 0000

DMA7STB 03DA STB<15:0> 0000

DMA7PAD 03DC PAD<15:0> 0000

DMA7CNT 03DE — — — — — — CNT<9:0> 0000

DMACS0 03E0 PWCOL7 PWCOL6 PWCOL5 PWCOL4 PWCOL3 PWCOL2 PWCOL1 PWCOL0 XWCOL7 XWCOL6 XWCOL5 XWCOL4 XWCOL3 XWCOL2 XWCOL1 XWCOL0 0000

DMACS1 03E2 — — — — LSTCH<3:0> PPST7 PPST6 PPST5 PPST4 PPST3 PPST2 PPST1 PPST0 0000

DSADR 03E4 DSADR<15:0> 0000

TABLE 4-17: DMA REGISTER MAP (CONTINUED)

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 4-18: ECAN1 REGISTER MAP WHEN C1CTRL1.WIN = 0 OR 1 FOR dsPIC33FJXXXGP506A/51A0/706A/708A/710A DEVICES ONLY

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

C1CTRL1 0400 —— CSIDL ABAT — REQOP<2:0> OPMODE<2:0> —CANCAP——WIN0480

C1CTRL2 0402 — — — — — — — — — — — DNCNT<4:0> 0000

C1VEC 0404 ——— FILHIT<4:0> — ICODE<6:0> 0000

C1FCTRL 0406 DMABS<2:0> — — — — — — — — FSA<4:0> 0000

C1FIFO 0408 ——FBP<5:0> —— FNRB<5:0> 0000

C1INTF 040A —— TXBO TXBP RXBP TXWAR RXWAR EWARN IVRIF WAKIF ERRIF — FIFOIF RBOVIF RBIF TBIF 0000

C1INTE 040C — — — — — — — — IVRIE WAKIE ERRIE — FIFOIE RBOVIE RBIE TBIE 0000

C1EC 040E TERRCNT<7:0> RERRCNT<7:0> 0000

C1CFG1 0410 — — — — — — — — SJW<1:0> BRP<5:0> 0000

C1CFG2 0412 —WAKFIL— — — SEG2PH<2:0> SEG2PHTS SAM SEG1PH<2:0> PRSEG<2:0> 0000

C1FEN1 0414

FLTEN15 FLTEN14 FLTEN13 FLTEN12 FLTEN11 FLTEN10 FLTEN9 FLTEN8 FLTEN7 FLTEN6 FLTEN5 FLTEN4 FLTEN3 FLTEN2 FLTEN1 FLTEN0

FFFF

C1FMSKSEL1 0418 F7MSK<1:0> F6MSK<1:0> F5MSK<1:0> F4MSK<1:0> F3MSK<1:0> F2MSK<1:0> F1MSK<1:0> F0MSK<1:0> 0000

C1FMSKSEL2 041A F15MSK<1:0> F14MSK<1:0> F13MSK<1:0> F12MSK<1:0> F11MSK<1:0> F10MSK<1:0> F9MSK<1:0> F8MSK<1:0> 0000

Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

TABLE 4-19: ECAN1 REGISTER MAP WHEN C1CTRL1.WIN = 0 FOR dsPIC33FJXXXGP506A/510A/706A/708A/710A DEVICES ONLY

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

0400-

041E

See definition when WIN = x

C1RXFUL1 0420 RXFUL15 RXFUL14 RXFUL13 RXFUL12 RXFUL11 RXFUL10 RXFUL9 RXFUL8 RXFUL7 RXFUL6 RXFUL5 RXFUL4 RXFUL3 RXFUL2 RXFUL1 RXFUL0 0000

C1RXFUL2 0422 RXFUL31 RXFUL30 RXFUL29 RXFUL28 RXFUL27 RXFUL26 RXFUL25 RXFUL24 RXFUL23 RXFUL22 RXFUL21 RXFUL20 RXFUL19 RXFUL18 RXFUL17 RXFUL16 0000

C1RXOVF1 0428 RXOVF15 RXOVF14 RXOVF13 RXOVF12 RXOVF11 RXOVF10 RXOVF9 RXOVF8 RXOVF7 RXOVF6 RXOVF5 RXOVF4 RXOVF3 RXOVF2 RXOVF1 RXOVF0 0000

C1RXOVF2 042A RXOVF31 RXOVF30 RXOVF29 RXOVF28 RXOVF27 RXOVF26 RXOVF25 RXOVF24 RXOVF23 RXOVF22 RXOVF21 RXOVF20 RXOVF19 RXOVF18 RXOVF17 RXOVF16 0000

C1TR01CON 0430

TXEN1 TXABT1 TXLARB1 TXERR1 TXREQ1 RTREN1 TX1PRI<1:0> TXEN0 TXABAT0 TXLARB0 TXERR0 TXREQ0 RTREN0 TX0PRI<1:0>

0000

C1TR23CON 0432

TXEN3 TXABT3 TXLARB3 TXERR3 TXREQ3 RTREN3 TX3PRI<1:0> TXEN2 TXABAT2 TXLARB2 TXERR2 TXREQ2 RTREN2 TX2PRI<1:0>

0000

C1TR45CON 0434

TXEN5 TXABT5 TXLARB5 TXERR5 TXREQ5 RTREN5 TX5PRI<1:0> TXEN4 TXABAT4 TXLARB4 TXERR4 TXREQ4 RTREN4 TX4PRI<1:0>

0000

C1TR67CON 0436

TXEN7 TXABT7 TXLARB7 TXERR7 TXREQ7 RTREN7 TX7PRI<1:0> TXEN6 TXABAT6 TXLARB6 TXERR6 TXREQ6 RTREN6 TX6PRI<1:0>

xxxx

C1RXD 0440 Received Data Word xxxx

C1TXD 0442 Transmit Data Word xxxx

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 4-20: ECAN1 REGISTER MAP WHEN C1CTRL1.WIN = 1 FOR dsPIC33FJXXXGP506A/510A/706A/708A/710A DEVICES ONLY

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

0400-

041E

See definition when WIN = x

C1BUFPNT1 0420 F3BP<3:0> F2BP<3:0> F1BP<3:0> F0BP<3:0> 0000

C1BUFPNT2 0422 F7BP<3:0> F6BP<3:0> F5BP<3:0> F4BP<3:0> 0000

C1BUFPNT3 0424 F11BP<3:0> F10BP<3:0> F9BP<3:0> F8BP<3:0> 0000

C1BUFPNT4 0426 F15BP<3:0> F14BP<3:0> F13BP<3:0> F12BP<3:0> 0000

C1RXM0SID 0430 SID<10:3> SID<2:0> —MIDE— EID<17:16> xxxx

C1RXM0EID 0432 EID<15:8> EID<7:0> xxxx

C1RXM1SID 0434 SID<10:3> SID<2:0> —MIDE— EID<17:16> xxxx

C1RXM1EID 0436 EID<15:8> EID<7:0> xxxx

C1RXM2SID 0438 SID<10:3> SID<2:0> —MIDE— EID<17:16> xxxx

C1RXM2EID 043A EID<15:8> EID<7:0> xxxx

C1RXF0SID 0440 SID<10:3> SID<2:0> —EXIDE— EID<17:16> xxxx

C1RXF0EID 0442 EID<15:8> EID<7:0> xxxx

C1RXF1SID 0444 SID<10:3> SID<2:0> —EXIDE— EID<17:16> xxxx

C1RXF1EID 0446 EID<15:8> EID<7:0> xxxx

C1RXF2SID 0448 SID<10:3> SID<2:0> —EXIDE— EID<17:16> xxxx

C1RXF2EID 044A EID<15:8> EID<7:0> xxxx

C1RXF3SID 044C SID<10:3> SID<2:0> —EXIDE— EID<17:16> xxxx

C1RXF3EID 044E EID<15:8> EID<7:0> xxxx

C1RXF4SID 0450 SID<10:3> SID<2:0> —EXIDE— EID<17:16> xxxx

C1RXF4EID 0452 EID<15:8> EID<7:0> xxxx

C1RXF5SID 0454 SID<10:3> SID<2:0> —EXIDE— EID<17:16> xxxx

C1RXF5EID 0456 EID<15:8> EID<7:0> xxxx

C1RXF6SID 0458 SID<10:3> SID<2:0> —EXIDE— EID<17:16> xxxx

C1RXF6EID 045A EID<15:8> EID<7:0> xxxx

C1RXF7SID 045C SID<10:3> SID<2:0> —EXIDE— EID<17:16> xxxx

C1RXF7EID 045E EID<15:8> EID<7:0> xxxx

C1RXF8SID 0460 SID<10:3> SID<2:0> —EXIDE— EID<17:16> xxxx

C1RXF8EID 0462 EID<15:8> EID<7:0> xxxx

C1RXF9SID 0464 SID<10:3> SID<2:0> —EXIDE— EID<17:16> xxxx

C1RXF9EID 0466 EID<15:8> EID<7:0> xxxx

C1RXF10SID 0468 SID<10:3> SID<2:0> —EXIDE— EID<17:16> xxxx

C1RXF10EID 046A EID<15:8> EID<7:0> xxxx

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33FJXXXGPX06A/X08A/X10A

C1RXF11SID 046C SID<10:3> SID<2:0> —EXIDE— EID<17:16> xxxx

C1RXF11EID 046E EID<15:8> EID<7:0> xxxx

C1RXF12SID 0470 SID<10:3> SID<2:0> —EXIDE— EID<17:16> xxxx

C1RXF12EID 0472 EID<15:8> EID<7:0> xxxx

C1RXF13SID 0474 SID<10:3> SID<2:0> —EXIDE— EID<17:16> xxxx

C1RXF13EID 0476 EID<15:8> EID<7:0> xxxx

C1RXF14SID 0478 SID<10:3> SID<2:0> —EXIDE— EID<17:16> xxxx

C1RXF14EID 047A EID<15:8> EID<7:0> xxxx

C1RXF15SID 047C SID<10:3> SID<2:0> —EXIDE— EID<17:16> xxxx

C1RXF15EID 047E EID<15:8> EID<7:0> xxxx

TABLE 4-20: ECAN1 REGISTER MAP WHEN C1CTRL1.WIN = 1 FOR dsPIC33FJXXXGP506A/510A/706A/708A/710A DEVICES ONLY

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 4-21: ECAN2 REGISTER MAP WHEN C2CTRL1.WIN = 0 OR 1 FOR dsPIC33FJXXXGP706A/708A/710A DEVICES ONLY

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

C2CTRL1 0500 ——CSIDLABAT — REQOP<2:0> OPMODE<2:0> — CANCAP ——WIN0480

C2CTRL2 0502 — — — — — — — — — — — DNCNT<4:0> 0000

C2VEC 0504 — — — FILHIT<4:0> — ICODE<6:0> 0000

C2FCTRL 0506 DMABS<2:0> — — — — — — — — FSA<4:0> 0000

C2FIFO 0508 —— FBP<5:0> —— FNRB<5:0> 0000

C2INTF 050A —— TXBO TXBP RXBP TXWAR RXWAR EWARN IVRIF WAKIF ERRIF — FIFOIF RBOVIF RBIF TBIF 0000

C2INTE 050C — — — — — — — — IVRIE WAKIE ERRIE — FIFOIE RBOVIE RBIE TBIE 0000

C2EC 050E TERRCNT<7:0> RERRCNT<7:0> 0000

C2CFG1 0510 — — — — — — — — SJW<1:0> BRP<5:0> 0000

C2CFG2 0512 — WAKFIL — — — SEG2PH<2:0> SEG2PHTS SAM SEG1PH<2:0> PRSEG<2:0> 0000

C2FEN1 0514 FLTEN15 FLTEN14 FLTEN13 FLTEN12 FLTEN11 FLTEN10 FLTEN9 FLTEN8 FLTEN7 FLTEN6 FLTEN5 FLTEN4 FLTEN3 FLTEN2 FLTEN1 FLTEN0 FFFF

C2FMSKSEL1 0518 F7MSK<1:0> F6MSK<1:0> F5MSK<1:0> F4MSK<1:0> F3MSK<1:0> F2MSK<1:0> F1MSK<1:0> F0MSK<1:0> 0000

C2FMSKSEL2 051A F15MSK<1:0> F14MSK<1:0> F13MSK<1:0> F12MSK<1:0> F11MSK<1:0> F10MSK<1:0> F9MSK<1:0> F8MSK<1:0> 0000

Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

TABLE 4-22: ECAN2 REGISTER MAP WHEN C2CTRL1.WIN = 0 FOR dsPIC33FJXXXGP706A/708A/710A DEVICES ONLY

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

0500-

051E

See definition when WIN = x

C2RXFUL1 0520 RXFUL15 RXFUL14 RXFUL13 RXFUL12 RXFUL11 RXFUL10 RXFUL9 RXFUL8 RXFUL7 RXFUL6 RXFUL5 RXFUL4 RXFUL3 RXFUL2 RXFUL1 RXFUL0 0000

C2RXFUL2 0522 RXFUL31 RXFUL30 RXFUL29 RXFUL28 RXFUL27 RXFUL26 RXFUL25 RXFUL24 RXFUL23 RXFUL22 RXFUL21 RXFUL20 RXFUL19 RXFUL18 RXFUL17 RXFUL16 0000

C2RXOVF1 0528 RXOVF15 RXOVF14 RXOVF13 RXOVF12 RXOVF11 RXOVF10 RXOVF09 RXOVF08 RXOVF7 RXOVF6 RXOVF5 RXOVF4 RXOVF3 RXOVF2 RXOVF1 RXOVF0 0000

C2RXOVF2 052A RXOVF31 RXOVF30 RXOVF29 RXOVF28 RXOVF27 RXOVF26 RXOVF25 RXOVF24 RXOVF23 RXOVF22 RXOVF21 RXOVF20 RXOVF19 RXOVF18 RXOVF17 RXOVF16 0000

C2TR01CON 0530 TXEN1 TX

ABAT1

LARB1

ERR1

REQ1

RTREN1 TX1PRI<1:0> TXEN0 TX

ABAT0

LARB0

ERR0

REQ0

RTREN0 TX0PRI<1:0> 0000

C2TR23CON 0532 TXEN3 TX

ABAT3

LARB3

ERR3

REQ3

RTREN3 TX3PRI<1:0> TXEN2 TX

ABAT2

LARB2

ERR2

REQ2

RTREN2 TX2PRI<1:0> 0000

C2TR45CON 0534 TXEN5 TX

ABAT5

LARB5

ERR5

REQ5

RTREN5 TX5PRI<1:0> TXEN4 TX

ABAT4

LARB4

ERR4

REQ4

RTREN4 TX4PRI<1:0> 0000

C2TR67CON 0536 TXEN7 TX

ABAT7

LARB7

ERR7

REQ7

RTREN7 TX7PRI<1:0> TXEN6 TX

ABAT6

LARB6

ERR6

REQ6

RTREN6 TX6PRI<1:0> xxxx

C2RXD 0540 Recieved Data Word xxxx

C2TXD 0542 Transmit Data Word xxxx

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 4-23: ECAN2 REGISTER MAP WHEN C2CTRL1.WIN = 1 FOR dsPIC33FJXXXGP706A/708A/710A DEVICES ONLY

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

0500

051E

See definition when WIN = x

C2BUFPNT1 0520 F3BP<3:0> F2BP<3:0> F1BP<3:0> F0BP<3:0> 0000

C2BUFPNT2 0522 F7BP<3:0> F6BP<3:0> F5BP<3:0> F4BP<3:0> 0000

C2BUFPNT3 0524 F11BP<3:0> F10BP<3:0> F9BP<3:0> F8BP<3:0> 0000

C2BUFPNT4 0526 F15BP<3:0> F14BP<3:0> F13BP<3:0> F12BP<3:0> 0000

C2RXM0SID 0530 SID<10:3> SID<2:0> —MIDE— EID<17:16> xxxx

C2RXM0EID 0532 EID<15:8> EID<7:0> xxxx

C2RXM1SID 0534 SID<10:3> SID<2:0> —MIDE— EID<17:16> xxxx

C2RXM1EID 0536 EID<15:8> EID<7:0> xxxx

C2RXM2SID 0538 SID<10:3> SID<2:0> —MIDE— EID<17:16> xxxx

C2RXM2EID 053A EID<15:8> EID<7:0> xxxx

C2RXF0SID 0540 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF0EID 0542 EID<15:8> EID<7:0> xxxx

C2RXF1SID 0544 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF1EID 0546 EID<15:8> EID<7:0> xxxx

C2RXF2SID 0548 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF2EID 054A EID<15:8> EID<7:0> xxxx

C2RXF3SID 054C SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF3EID 054E EID<15:8> EID<7:0> xxxx

C2RXF4SID 0550 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF4EID 0552 EID<15:8> EID<7:0> xxxx

C2RXF5SID 0554 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF5EID 0556 EID<15:8> EID<7:0> xxxx

C2RXF6SID 0558 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF6EID 055A EID<15:8> EID<7:0> xxxx

C2RXF7SID 055C SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF7EID 055E EID<15:8> EID<7:0> xxxx

C2RXF8SID 0560 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF8EID 0562 EID<15:8> EID<7:0> xxxx

C2RXF9SID 0564 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF9EID 0566 EID<15:8> EID<7:0> xxxx

C2RXF10SID 0568 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33FJXXXGPX06A/X08A/X10A

C2RXF10EID 056A EID<15:8> EID<7:0> xxxx

C2RXF11SID 056C SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF11EID 056E EID<15:8> EID<7:0> xxxx

C2RXF12SID 0570 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF12EID 0572 EID<15:8> EID<7:0> xxxx

C2RXF13SID 0574 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF13EID 0576 EID<15:8> EID<7:0> xxxx

C2RXF14SID 0578 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF14EID 057A EID<15:8> EID<7:0> xxxx

C2RXF15SID 057C SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF15EID 057E EID<15:8> EID<7:0> xxxx

TABLE 4-23: ECAN2 REGISTER MAP WHEN C2CTRL1.WIN = 1 FOR dsPIC33FJXXXGP706A/708A/710A DEVICES ONLY (CONTINUED)

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 4-24: DCI REGISTER MAP

SFR

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset State

DCICON1 0280 DCIEN —DCISIDL— DLOOP CSCKD CSCKE COFSD UNFM CSDOM DJST — — — COFSM1 COFSM0 0000 0000 0000 0000

DCICON2 0282 — — — —BLEN1BLEN0 —COFSG<3:0>—WS<3:0>0000 0000 0000 0000

DCICON3 0284 — — — — BCG<11:0> 0000 0000 0000 0000

DCISTAT 0286 — — — — SLOT3 SLOT2 SLOT1 SLOT0 — — — — ROV RFUL TUNF TMPTY 0000 0000 0000 0000

TSCON 0288 TSE15 TSE14 TSE13 TSE12 TSE11 TSE10 TSE9 TSE8 TSE7 TSE6 TSE5 TSE4 TSE3 TSE2 TSE1 TSE0 0000 0000 0000 0000

RSCON 028C RSE15 RSE14 RSE13 RSE12 RSE11 RSE10 RSE9 RSE8 RSE7 RSE6 RSE5 RSE4 RSE3 RSE2 RSE1 RSE0 0000 0000 0000 0000

RXBUF0 0290 Receive Buffer #0 Data Register 0000 0000 0000 0000

RXBUF1 0292 Receive Buffer #1 Data Register 0000 0000 0000 0000

RXBUF2 0294 Receive Buffer #2 Data Register 0000 0000 0000 0000

RXBUF3 0296 Receive Buffer #3 Data Register 0000 0000 0000 0000

TXBUF0 0298 Transmit Buffer #0 Data Register 0000 0000 0000 0000

TXBUF1 029A Transmit Buffer #1 Data Register 0000 0000 0000 0000

TXBUF2 029C Transmit Buffer #2 Data Register 0000 0000 0000 0000

TXBUF3 029E Transmit Buffer #3 Data Register 0000 0000 0000 0000

Legend: — = unimplemented, read as ‘0’.

Note 1: Refer to the “dsPIC33F/PIC24H Family Reference Manual” for descriptions of register bit fields.

TABLE 4-25: PORTA REGISTER MAP(1)

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TRISA 02C0

TRISA15 TRISA14 TRISA13 TRISA12 — TRISA10 TRISA9 — TRISA7 TRISA6 TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0

F6FF

PORTA 02C2

RA15 RA14 RA13 RA12 — RA10 RA9 — RA7 RA6 RA5 RA4 RA3 RA2 RA1 RA0

xxxx

LATA 02C4

LATA15 LATA14 LATA13 LATA12 — LATA10 LATA9 — LATA7 LATA6 LATA5 LATA4 LATA3 LATA2 LATA1 LATA0

xxxx

ODCA

(2)

06C0

ODCA15 ODCA14

— — — — — — — —

ODCA5 ODCA4 ODCA3 ODCA2 ODCA1 ODCA0

0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.

Note 1: The actual set of I/O port pins varies from one device to another. Please refer to the corresponding pinout diagrams.

TABLE 4-26: PORTB REGISTER MAP(1)

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TRISB 02C6 TRISB15 TRISB14 TRISB13 TRISB12 TRISB11 TRISB10 TRISB9 TRISB8 TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0

FFFF

PORTB 02C8 RB15 RB14 RB13 RB12 RB11 RB10 RB9 RB8 RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0

xxxx

LATB 02CA LATB15 LATB14 LATB13 LATB12 LATB11 LATB10 LATB9 LATB8 LATB7 LATB6 LATB5 LATB4 LATB3 LATB2 LATB1 LATB0

xxxx

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.

Note 1: The actual set of I/O port pins varies from one device to another. Please refer to the corresponding pinout diagrams.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 4-27: PORTC REGISTER MAP(1)

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TRISC 02CC TRISC15 TRISC14 TRISC13 TRISC12 ———————

TRISC4 TRISC3 TRISC2 TRISC1 —

F01E

PORTC 02CE RC15 RC14 RC13 RC12 ———————

RC4 RC3 RC2 RC1 —

xxxx

LATC 02D0 LATC15 LATC14 LATC13 LATC12 ———————

LATC4 LATC3 LATC2 LATC1 —

xxxx

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.

Note 1: The actual set of I/O port pins varies from one device to another. Please refer to the corresponding pinout diagrams.

TABLE 4-28: PORTD REGISTER MAP(1)

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TRISD 02D2

TRISD15 TRISD14 TRISD13 TRISD12

TRISD11 TRISD10 TRISD9 TRISD8 TRISD7 TRISD6 TRISD5 TRISD4 TRISD3 TRISD2 TRISD1 TRISD0

FFFF

PORTD 02D4

RD15 RD14 RD13 RD12

RD11 RD10 RD9 RD8 RD7 RD6 RD5 RD4 RD3 RD2 RD1 RD0

xxxx

LATD 02D6

LATD15 LATD14 LATD13 LATD12

LATD11 LATD10 LATD9 LATD8 LATD7 LATD6 LATD5 LATD4 LATD3 LATD2 LATD1 LATD0

xxxx

ODCD 06D2

ODCD15 ODCD14 ODCD13 ODCD12 ODCD11 ODCD10 ODCD9 ODCD8 ODCD7 ODCD6 ODCD5 ODCD4 ODCD3 ODCD2 ODCD1 ODCD0

0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.

Note 1: The actual set of I/O port pins varies from one device to another. Please refer to the corresponding pinout diagrams.

TABLE 4-29: PORTE REGISTER MAP(1)

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TRISE 02D8 ————————

TRISE7

TRISE6 TRISE5 TRISE4 TRISE3 TRISE2 TRISE1 TRISE0

00FF

PORTE 02DA ————————

RE7

RE6 RE5 RE4 RE3 RE2 RE1 RE0

xxxx

LATE 02DC ————————

LATE7

LATE6 LATE5 LATE4 LATE3 LATE2 LATE1 LATE0

xxxx

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.

Note 1: The actual set of I/O port pins varies from one device to another. Please refer to the corresponding pinout diagrams.

TABLE 4-30: PORTF REGISTER MAP(1)

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets

TRISF 02DE — —

TRISF13 TRISF12

— — —

TRISF8 TRISF7

TRISF6 TRISF5 TRISF4 TRISF3 TRISF2 TRISF1 TRISF0

31FF

PORTF 02E0 — —

RF13 RF12

— — — RF8 RF7 RF6 RF5 RF4 RF3 RF2 RF1 RF0

xxxx

LATF 02E2 — —

LATF13 LATF12

— — — LATF8 LATF7 LATF6 LATF5 LATF4 LATF3 LATF2 LATF1 LATF0

xxxx

ODCF 06DE — —

ODCF13 ODCF12

— — —

ODCF8 ODCF7 ODCF6 ODCF5 ODCF4 ODCF3 ODCF2 ODCF1 ODCF0

0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.

Note 1: The actual set of I/O port pins varies from one device to another. Please refer to the corresponding pinout diagrams.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 4-31: PORTG REGISTER MAP(1)

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TRISG 02E4

TRISG15 TRISG14 TRISG13 TRISG12 —— TRISG9 TRISG8 TRISG7 TRISG6 —— TRISG3 TRISG2 TRISG1 TRISG0

F3CF

PORTG 02E6

RG15 RG14 RG13 RG12 —— RG9 RG8 RG7 RG6 —— RG3 RG2 RG1 RG0

xxxx

LATG 02E8

LATG15 LATG14 LATG13 LATG12 —— LATG9 LATG8 LATG7 LATG6 —— LATG3 LATG2 LATG1 LATG0

xxxx

ODCG 06E4

ODCG15 ODCG14 ODCG13 ODCG12

— —

ODCG9 ODCG8 ODCG7 ODCG6

— —

ODCG3 ODCG2 ODCG1 ODCG0

0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.

Note 1: The actual set of I/O port pins varies from one device to another. Please refer to the corresponding pinout diagrams.

TABLE 4-32: SYSTEM CONTROL REGISTER MAP

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

RCON 0740 TRAPR IOPUWR — — — — — VREGS EXTR SWR SWDTEN WDTO SLEEP IDLE BOR POR

xxxx

(1)

OSCCON 0742 — COSC<2:0> — NOSC<2:0> CLKLOCK —LOCK—CF— LPOSCEN OSWEN 0300

(2)

CLKDIV 0744 ROI DOZE<2:0> DOZEN FRCDIV<2:0> PLLPOST<1:0> — PLLPRE<4:0> 3040

PLLFBD 0746 ——————— PLLDIV<8:0> 0030

OSCTUN 0748 — — — — — — — — — —TUN<5:0>0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

Note 1: RCON register Reset values dependent on type of Reset.

2: OSCCON register Reset values dependent on the FOSC Configuration bits and by type of Reset.

TABLE 4-33: NVM REGISTER MAP

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11Bit 10Bit 9Bit 8Bit 7Bit 6Bit 5Bit 4Bit 3Bit 2Bit 1Bit 0 All

Resets

NVMCON 0760 WR WREN WRERR ——————ERASE——NVMOP<3:0>

0000

(1)

NVMKEY 0766

———————— NVMKEY<7:0>

0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

Note 1: Reset value shown is for POR only. Value on other Reset states is dependent on the state of memory write or erase operations at the time of Reset.

TABLE 4-34: PMD REGISTER MAP

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

PMD1 0770 T5MD T4MD T3MD T2MD T1MD — — DCIMD I2C1MD U2MD U1MD SPI2MD SPI1MD C2MD C1MD AD1MD 0000

PMD2 0772 IC8MD IC7MD IC6MD IC5MD IC4MD IC3MD IC2MD IC1MD OC8MD OC7MD OC6MD OC5MD OC4MD OC3MD OC2MD OC1MD 0000

PMD3 0774 T9MD T8MD T7MD T6MD — — — — — — — — — —I2C2MDAD2MD0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33FJXXXGPX06A/X08A/X10A

4.2.7 SOFTWARE STACK

In addition to its use as a working register, the W15

devices is also used as a software Stack Pointer. The

Stack Pointer always points to the first available free

word and grows from lower to higher addresses. It

pre-decrements for stack pops and post-increments for

stack pushes, as shown in Figure 4-6. For a PC push

during any CALL instruction, the MSb of the PC is

zero-extended before the push, ensuring that the MSb

is always clear.

The Stack Pointer Limit register (SPLIM) associated

with the Stack Pointer sets an upper address boundary

for the stack. SPLIM is uninitialized at Reset. As is the

case for the Stack Pointer, SPLIM<0> is forced to ‘0’

because all stack operations must be word-aligned.

Whenever an EA is generated using W15 as a source

or destination pointer, the resulting address is

compared with the value in SPLIM. If the contents of

the Stack Pointer (W15) and the SPLIM register are

equal and a push operation is performed, a stack error

trap will not occur. The stack error trap will occur on a

subsequent push operation. Thus, for example, if it is

desirable to cause a stack error trap when the stack

grows beyond address 0x2000 in RAM, initialize the

SPLIM with the value 0x1FFE.

Similarly, a Stack Pointer underflow (stack error) trap is

generated when the Stack Pointer address is found to

be less than 0x0800. This prevents the stack from

interfering with the Special Function Register (SFR)

space.

A write to the SPLIM register should not be immediately

followed by an indirect read operation using W15.

FIGURE 4-6: CALL STACK FRAME

4.2.8 DATA RAM PROTECTION FEATURE

The dsPIC33F product family supports Data RAM

protection features which enable segments of RAM to

be protected when used in conjunction with Boot and

Secure Code Segment Security. BSRAM (Secure RAM

segment for BS) is accessible only from the Boot

Segment Flash code when enabled. SSRAM (Secure

RAM segment for RAM) is accessible only from the

Secure Segment Flash code when enabled. See

Table 4-1 for an overview of the BSRAM and SSRAM

SFRs.

4.3 Instruction Addressing Modes

The addressing modes in Ta b l e 4 - 3 5 form the basis of

the addressing modes optimized to support the specific

features of individual instructions. The addressing

modes provided in the MAC class of instructions are

somewhat different from those in the other instruction

types.

4.3.1 FILE REGISTER INSTRUCTIONS

Most file register instructions use a 13-bit address field

(f) to directly address data present in the first 8192

bytes of data memory (Near Data Space). Most file

which is denoted as WREG in these instructions. The

destination is typically either the same file register or

WREG (with the exception of the MUL instruction),

which writes the result to a register or register pair. The

MOV instruction allows additional flexibility and can

access the entire data space.

4.3.2 MCU INSTRUCTIONS

The 3-operand MCU instructions are of the form:

Operand 3 = Operand 1 <function> Operand 2

where:

Operand 1 is always a working register (i.e., the

addressing mode can only be register direct) which is

referred to as Wb.

Operand 2 can be a W register, fetched from data

memory, or a 5-bit literal. The result location can be

either a W register or a data memory location. The

following addressing modes are supported by MCU

instructions:

• Register Direct

• Register Indirect

• Register Indirect Post-Modified

• Register Indirect Pre-Modified

• 5-bit or 10-bit Literal

Note: A PC push during exception processing

concatenates the SRL register to the MSb

of the PC prior to the push.

PC<15:0>

000000000

015

W15 (before CALL)

W15 (after CALL)

Stack Grows Towards

Higher Address

0x0000

PC<22:16>

POP : [--W15]

PUSH : [W15++]

Note: Not all instructions support all the

addressing modes given above.

Individual instructions may support

different subsets of these addressing

modes.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 4-35: FUNDAMENTAL ADDRESSING MODES SUPPORTED

4.3.3 MOVE AND ACCUMULATOR

INSTRUCTIONS

Move instructions and the DSP accumulator class of

instructions provide a greater degree of addressing

flexibility than other instructions. In addition to the

Addressing modes supported by most MCU

instructions, move and accumulator instructions also

support Register Indirect with Register Offset

Addressing mode, also referred to as Register Indexed

mode.

In summary, the following Addressing modes are

supported by move and accumulator instructions:

• Register Direct

• Register Indirect

• Register Indirect Post-modified

• Register Indirect Pre-modified

• Register Indirect with Register Offset (Indexed)

• Register Indirect with Literal Offset

• 8-bit Literal

• 16-bit Literal

4.3.4 MAC INSTRUCTIONS

The dual source operand DSP instructions (CLR, ED,

EDAC, MAC, MPY, MPY.N, MOVSAC and MSC), also referred

to as MAC instructions, utilize a simplified set of

addressing modes to allow the user to effectively

manipulate the data pointers through register indirect

tables.

The 2-source operand prefetch registers must be

members of the set {W8, W9, W10, W11}. For data

reads, W8 and W9 are always directed to the X RAGU

and W10 and W11 will always be directed to the Y

AGU. The effective addresses generated (before and

after modification) must, therefore, be valid addresses

within X data space for W8 and W9 and Y data space

for W10 and W11.

In summary, the following addressing modes are

supported by the MAC class of instructions:

• Register Indirect

• Register Indirect Post-Modified by 2

• Register Indirect Post-Modified by 4

• Register Indirect Post-Modified by 6

• Register Indirect with Register Offset (Indexed)

4.3.5 OTHER INSTRUCTIONS

Besides the various addressing modes outlined above,

some instructions use literal constants of various sizes.

For example, BRA (branch) instructions use 16-bit signed

literals to specify the branch destination directly, whereas

the DISI instruction uses a 14-bit unsigned literal field. In

some instructions, such as ADD Acc, the source of an

operand or result is implied by the opcode itself. Certain

operations, such as NOP, do not have any operands.

4.4 Modulo Addressing

Modulo Addressing mode is a method of providing an

automated means to support circular data buffers using

hardware. The objective is to remove the need for

software to perform data address boundary checks

when executing tightly looped code, as is typical in

many DSP algorithms.

Modulo Addressing can operate in either data or program

space (since the data pointer mechanism is essentially

the same for both). One circular buffer can be supported

in each of the X (which also provides the pointers into

program space) and Y data spaces. Modulo Addressing

Addressing Mode Description

File Register Direct The address of the file register is specified explicitly.

decremented) by a constant value.

to form the EA.

Note: For the MOV instructions, the Addressing

mode specified in the instruction can differ

for the source and destination EA.

However, the 4-bit Wb (Register Offset)

field is shared between both source and

destination (but typically only used by

one).

Note: Not all instructions support all the

Addressing modes given above.

Individual instructions may support

different subsets of these Addressing

modes.

Note: Register Indirect with Register Offset

Addressing mode is only available for W9

(in X space) and W11 (in Y space).

dsPIC33FJXXXGPX06A/X08A/X10A

can operate on any W register pointer. However, it is not

advisable to use W14 or W15 for Modulo Addressing

since these two registers are used as the Stack Frame

Pointer and Stack Pointer, respectively.

In general, any particular circular buffer can only be

configured to operate in one direction as there are

certain restrictions on the buffer start address (for incre-

menting buffers), or end address (for decrementing

buffers), based upon the direction of the buffer.

The only exception to the usage restrictions is for

buffers which have a power-of-2 length. As these

buffers satisfy the start and end address criteria, they

may operate in a bidirectional mode (i.e., address

boundary checks will be performed on both the lower

and upper address boundaries).

4.4.1 START AND END ADDRESS

The Modulo Addressing scheme requires that a starting

and ending address be specified and loaded into the

16-bit Modulo Buffer Address registers: XMODSRT,

XMODEND, YMODSRT and YMODEND (see

Table 4-1).

The length of a circular buffer is not directly specified. It

is determined by the difference between the

corresponding start and end addresses. The maximum

possible length of the circular buffer is 32K words

(64 Kbytes).

4.4.2 W ADDRESS REGISTER

SELECTION

The Modulo and Bit-Reversed Addressing Control

as a W register field to specify the W Address registers.

The XWM and YWM fields select which registers will

operate with Modulo Addressing. If XWM = 15, X RAGU

and X WAGU Modulo Addressing is disabled. Similarly, if

YWM = 15, Y AGU Modulo Addressing is disabled.

The X Address Space Pointer W register (XWM), to

which Modulo Addressing is to be applied, is stored in

MODCON<3:0> (see Table 4-1). Modulo Addressing is

enabled for X data space when XWM is set to any value

other than ‘15’ and the XMODEN bit is set at

MODCON<15>.

The Y Address Space Pointer W register (YWM) to

which Modulo Addressing is to be applied is stored in

MODCON<7:4>. Modulo Addressing is enabled for Y

data space when YWM is set to any value other than

‘15’ and the YMODEN bit is set at MODCON<14>.

FIGURE 4-7: MODULO ADDRESSING OPERATION EXAMPLE

Note: Y space Modulo Addressing EA

calculations assume word sized data (LSb

of every EA is always clear).

0x1100

0x1163

Start Addr = 0x1100

End Addr = 0x1163

Length = 0x0032 words

Byte

Address MOV #0x1100, W0

MOV W0, XMODSRT ;set modulo start address

MOV #0x1163, W0

MOV W0, MODEND ;set modulo end address

MOV #0x8001, W0

MOV W0, MODCON ;enable W1, X AGU for modulo

MOV #0x0000, W0 ;W0 holds buffer fill value

MOV #0x1110, W1 ;point W1 to buffer

DO AGAIN, #0x31 ;fill the 50 buffer locations

MOV W0, [W1++] ;fill the next location

AGAIN: INC W0, W0 ;increment the fill value

dsPIC33FJXXXGPX06A/X08A/X10A

4.4.3 MODULO ADDRESSING

APPLICABILITY

Modulo Addressing can be applied to the Effective

Address (EA) calculation associated with any W

boundaries check for addresses less than, or greater

than, the upper (for incrementing buffers) and lower (for

decrementing buffers) boundary addresses (not just

equal to). Address changes may, therefore, jump

beyond boundaries and still be adjusted correctly.

4.5 Bit-Reversed Addressing

Bit-Reversed Addressing mode is intended to simplify

data re-ordering for radix-2 FFT algorithms. It is

supported by the X AGU for data writes only.

The modifier, which may be a constant value or register

contents, is regarded as having its bit order reversed. The

address source and destination are kept in normal order.

Thus, the only operand requiring reversal is the modifier.

4.5.1 BIT-REVERSED ADDRESSING

IMPLEMENTATION

Bit-Reversed Addressing mode is enabled when:

1. BWM bits (W register selection) in the

MODCON register are any value other than ‘15’

(the stack cannot be accessed using

Bit-Reversed Addressing).

2. The BREN bit is set in the XBREV register.

3. The addressing mode used is Register Indirect

with Pre-Increment or Post-Increment.

If the length of a bit-reversed buffer is M = 2N bytes,

the last ‘N’ bits of the data buffer start address must

be zeros.

XB<14:0> is the Bit-Reversed Address modifier, or

‘pivot point’, which is typically a constant. In the case of

an FFT computation, its value is equal to half of the FFT

data buffer size.

When enabled, Bit-Reversed Addressing is only

executed for Register Indirect with Pre-Increment or

Post-Increment Addressing and word sized data writes.

It will not function for any other addressing mode or for

byte sized data and normal addresses are generated

instead. When Bit-Reversed Addressing is active, the

W Address Pointer is always added to the address

modifier (XB) and the offset associated with the Regis-

ter Indirect Addressing mode is ignored. In addition, as

word sized data is a requirement, the LSb of the EA is

ignored (and always clear).

If Bit-Reversed Addressing has already been enabled

by setting the BREN bit (XBREV<15>), a write to the

XBREV register should not be immediately followed by

an indirect read operation using the W register that has

been designated as the bit-reversed pointer.

Note: The modulo corrected effective address is

written back to the register only when

Pre-Modify or Post-Modify Addressing

mode is used to compute the effective

address. When an address offset (e.g.,

[W7+W2]) is used, Modulo Address

correction is performed but the contents of

the register remain unchanged.

Note: All bit-reversed EA calculations assume

word sized data (LSb of every EA is

always clear). The XB value is scaled

accordingly to generate compatible (byte)

addresses.

Note: Modulo Addressing and Bit-Reversed

Addressing should not be enabled

together. In the event that the user

attempts to do so, Bit-Reversed Address-

ing will assume priority when active for the

X WAGU and X WAGU Modulo Addressing

will be disabled. However, Modulo

Addressing will continue to function in the X

RAGU.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 4-8: BIT-REVERSED ADDRESS EXAMPLE

TABLE 4-36: BIT-REVERSED ADDRESS SEQUENCE (16-ENTRY)

b3 b2 b1 0

b2 b3 b4 0

Bit Locations Swapped Left-to-Right

Around Center of Binary Value

Bit-Reversed Address

XB = 0x0008 for a 16-Word Bit-Reversed Buffer

b7 b6 b5 b1

b7 b6 b5 b4b11 b10 b9 b8

b11 b10 b9 b8

b15 b14 b13 b12

Sequential Address

Pivot Point

Normal Address Bit-Reversed Address

A3A2A1A0 Decimal A3A2A1A0 Decimal

0000 00000 0

0001 11000 8

0010 20100 4

0011 31100 12

0100 40010 2

0101 51010 10

0110 60110 6

0111 71110 14

1000 80001 1

1001 91001 9

1010 10 0101 5

1011 11 1101 13

1100 12 0011 3

1101 13 1011 11

1110 14 0111 7

1111 15 1111 15

dsPIC33FJXXXGPX06A/X08A/X10A

4.6 Interfacing Program and Data

Memory Spaces

The dsPIC33FJXXXGPX06A/X08A/X10A architecture

uses a 24-bit wide program space and a 16-bit wide

data space. The architecture is also a modified Harvard

scheme, meaning that data can also be present in the

program space. To use this data successfully, it must

be accessed in a way that preserves the alignment of

information in both spaces.

Aside from normal execution, the

dsPIC33FJXXXGPX06A/X08A/X10A architecture pro-

vides two methods by which program space can be

accessed during operation:

• Using table instructions to access individual bytes

or words anywhere in the program space

• Remapping a portion of the program space into

the data space (Program Space Visibility)

Table instructions allow an application to read or write

to small areas of the program memory. This capability

makes the method ideal for accessing data tables that

need to be updated from time to time. It also allows

access to all bytes of the program word. The

remapping method allows an application to access a

large block of data on a read-only basis, which is ideal

for look ups from a large table of static data. It can only

access the least significant word of the program word.

4.6.1 ADDRESSING PROGRAM SPACE

Since the address ranges for the data and program

spaces are 16 and 24 bits, respectively, a method is

needed to create a 23-bit or 24-bit program address

from 16-bit data registers. The solution depends on the

interface method to be used.

For table operations, the 8-bit Table Page register

(TBLPAG) is used to define a 32K word region within

the program space. This is concatenated with a 16-bit

EA to arrive at a full 24-bit program space address. In

this format, the Most Significant bit of TBLPAG is used

to determine if the operation occurs in the user memory

(TBLPAG<7> = 0) or the configuration memory

(TBLPAG<7> = 1).

For remapping operations, the 8-bit Program Space

Visibility register (PSVPAG) is used to define a

16K word page in the program space. When the Most

Significant bit of the EA is ‘1’, PSVPAG is concatenated

with the lower 15 bits of the EA to form a 23-bit program

space address. Unlike table operations, this limits

remapping operations strictly to the user memory area.

Table 4-37 and Figure 4-9 show how the program EA is

created for table operations and remapping accesses

from the data EA. Here, P<23:0> refers to a program

space word, whereas D<15:0> refers to a data space

word.

TABLE 4-37: PROGRAM SPACE ADDRESS CONSTRUCTION

Access Type Access

Space

Program Space Address

<23> <22:16> <15> <14:1> <0>

Instruction Access

(Code Execution)

User 0PC<22:1> 0

0xx xxxx xxxx xxxx xxxx xxx0

TBLRD/TBLWT

(Byte/Word Read/Write)

User TBLPAG<7:0> Data EA<15:0>

0xxx xxxx xxxx xxxx xxxx xxxx

Configuration TBLPAG<7:0> Data EA<15:0>

1xxx xxxx xxxx xxxx xxxx xxxx

Program Space Visibility

(Block Remap/Read)

User 0PSVPAG<7:0> Data EA<14:0>(1)

0 xxxx xxxx xxx xxxx xxxx xxxx

Note 1: Data EA<15> is always ‘1’ in this case, but is not used in calculating the program space address. Bit 15 of

the address is PSVPAG<0>.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 4-9: DATA ACCESS FROM PROGRAM SPACE ADDRESS GENERATION

0Program Counter

23 bits

PSVPAG

8 bits

15 bits

Program Counter(1)

Select

TBLPAG

8 bits

16 bits

Byte Select

1/0

User/Configuration

Table Operations(2)

Program Space Visibility(1)

Space Select

24 bits

23 bits

(Remapping)

1/0

Note 1: The LSb of program space addresses is always fixed as ‘0’ in order to maintain word

alignment of data in the program and data spaces.

2: Table operations are not required to be word-aligned. Table read operations are permitted

in the configuration memory space.

dsPIC33FJXXXGPX06A/X08A/X10A

4.6.2 DATA ACCESS FROM PROGRAM

MEMORY USING TABLE

INSTRUCTIONS

The TBLRDL and TBLWTL instructions offer a direct

method of reading or writing the lower word of any

address within the program space without going

through data space. The TBLRDH and TBLWTH

instructions are the only method to read or write the

upper 8 bits of a program space word as data.

The PC is incremented by two for each successive

24-bit program word. This allows program memory

addresses to directly map to data space addresses.

Program memory can thus be regarded as two 16-bit

word wide address spaces, residing side by side, each

with the same address range. TBLRDL and TBLWTL

access the space which contains the least significant

data word and TBLRDH and TBLWTH access the space

which contains the upper data byte.

Two table instructions are provided to move byte or

word sized (16-bit) data to and from program space.

Both function as either byte or word operations.

•TBLRDL (Table Read Low): In Word mode, it

maps the lower word of the program space

location (P<15:0>) to a data address (D<15:0>).

In Byte mode, either the upper or lower byte of the

lower program word is mapped to the lower byte of

a data address. The upper byte is selected when

Byte Select is ‘1’; the lower byte is selected when

it is ‘0’.

•TBLRDH (Table Read High): In Word mode, it

maps the entire upper word of a program address

(P<23:16>) to a data address. Note that D<15:8>,

the ‘phantom byte’, will always be ‘0’.

In Byte mode, it maps the upper or lower byte of

the program word to D<7:0> of the data address,

as above. Note that the data will always be ‘0’

when the upper ‘phantom’ byte is selected (Byte

Select = 1).

In a similar fashion, two table instructions, TBLWTH

and TBLWTL, are used to write individual bytes or

words to a program space address. The details of

their operation are explained in Section 5.0 “Flash

Program Memory”.

For all table operations, the area of program memory

space to be accessed is determined by the Table Page

memory space of the device, including user and

configuration spaces. When TBLPAG<7> = 0, the table

page is located in the user memory space. When

TBLPAG<7> = 1, the page is located in configuration

space.

FIGURE 4-10: ACCESSING PROGRAM MEMORY WITH TABLE INSTRUCTIONS

081623

00000000

‘Phantom’ Byte

TBLRDH.B (Wn<0> = 0)

TBLRDL.W

TBLRDL.B (Wn<0> = 1)

TBLRDL.B (Wn<0> = 0)

23 15 0

TBLPAG

0x000000

0x800000

0x020000

0x030000

Program Space

The address for the table operation is determined by the data EA

within the page defined by the TBLPAG register.

Only read operations are shown; write operations are also valid in

the user memory area.

dsPIC33FJXXXGPX06A/X08A/X10A

4.6.3 READING DATA FROM PROGRAM

MEMORY USING PROGRAM SPACE

VISIBILITY

The upper 32 Kbytes of data space may optionally be

mapped into any 16K word page of the program space.

This option provides transparent access of stored

constant data from the data space without the need to

use special instructions (i.e., TBLRDL/H).

Program space access through the data space occurs

if the Most Significant bit of the data space EA is ‘1’ and

program space visibility is enabled by setting the PSV

bit in the Core Control register (CORCON<2>). The

location of the program memory space to be mapped

into the data space is determined by the Program

Space Visibility Page register (PSVPAG). This 8-bit

16K words in program space. In effect, PSVPAG

functions as the upper 8 bits of the program memory

address, with the 15 bits of the EA functioning as the

lower bits. Note that by incrementing the PC by 2 for

each program memory word, the lower 15 bits of data

space addresses directly map to the lower 15 bits in the

corresponding program space addresses.

Data reads to this area add an additional cycle to the

instruction being executed, since two program memory

fetches are required.

Although each data space address, 8000h and higher,

maps directly into a corresponding program memory

address (see Figure 4-11), only the lower 16 bits of the

24-bit program word are used to contain the data. The

upper 8 bits of any program space location used as

data should be programmed with ‘1111 1111’ or

‘0000 0000’ to force a NOP. This prevents possible

issues should the area of code ever be accidentally

executed.

For operations that use PSV and are executed outside

a REPEAT loop, the MOV and MOV.D instructions

require one instruction cycle in addition to the specified

execution time. All other instructions require two

instruction cycles in addition to the specified execution

time.

For operations that use PSV, which are executed inside

a REPEAT loop, there will be some instances that

require two instruction cycles in addition to the

specified execution time of the instruction:

• Execution in the first iteration

• Execution in the last iteration

• Execution prior to exiting the loop due to an

interrupt

• Execution upon re-entering the loop after an

interrupt is serviced

Any other iteration of the REPEAT loop will allow the

instruction accessing data, using PSV, to execute in a

single cycle.

FIGURE 4-11: PROGRAM SPACE VISIBILITY OPERATION

Note: PSV access is temporarily disabled during

table reads/writes.

23 15 0

PSVPAG

Data Space

Program Space

0x0000

0x8000

0xFFFF

02 0x000000

0x800000

0x010000

0x018000

When CORCON<2> = 1 and EA<15> = 1:

The data in the page

designated by PSV-

PAG is mapped into

the upper half of the

data memory

space...

Data EA<14:0>

...while the lower 15 bits

of the EA specify an

exact address within

the PSV area. This

corresponds exactly to

the same lower 15 bits

of the actual program

space address.

PSV Area

dsPIC33FJXXXGPX06A/X08A/X10A

NOTES:

dsPIC33FJXXXGPX06A/X08A/X10A

5.0 FLASH PROGRAM MEMORY

The dsPIC33FJXXXGPX06A/X08A/X10A devices con-

tain internal Flash program memory for storing and

executing application code. The memory is readable,

writable and erasable during normal operation over the

entire VDD range.

Flash memory can be programmed in two ways:

• In-Circuit Serial Programming™ (ICSP™)

programming capability

• Run-Time Self-Programming (RTSP)

ICSP allows a dsPIC33FJXXXGPX06A/X08A/X10A

device to be serially programmed while in the end

application circuit. This is simply done with two lines for

programming clock and programming data (one of the

alternate programming pin pairs: PGECx/PGEDx), and

three other lines for power (VDD), ground (VSS) and

Master Clear (MCLR). This allows customers to manu-

facture boards with unprogrammed devices and then

program the digital signal controller just before shipping

the product. This also allows the most recent firmware

or a custom firmware to be programmed.

RTSP is accomplished using TBLRD (table read) and

TBLWT (table write) instructions. With RTSP, the user

can write program memory data either in blocks or

‘rows’ of 64 instructions (192 bytes) at a time or a single

program memory word, and erase program memory in

blocks or ‘pages’ of 512 instructions (1536 bytes) at a

time.

5.1 Table Instructions and Flash

Programming

Regardless of the method used, all programming of

Flash memory is done with the table read and table

write instructions. These allow direct read and write

access to the program memory space from the data

memory while the device is in normal operating mode.

The 24-bit target address in the program memory is

formed using bits<7:0> of the TBLPAG register and the

Effective Address (EA) from a W register specified in

the table instruction, as shown in Figure 5-1.

The TBLRDL and the TBLWTL instructions are used to

read or write to bits<15:0> of program memory.

TBLRDL and TBLWTL can access program memory in

both Word and Byte modes.

The TBLRDH and TBLWTH instructions are used to read

or write to bits<23:16> of program memory. TBLRDH

and TBLWTH can also access program memory in Word

or Byte mode.

FIGURE 5-1: ADDRESSING FOR TABLE REGISTERS

Note 1: This data sheet summarizes the features

of the dsPIC33FJXXXGPX06A/X08A/

X10A family of devices. However, it is not

intended to be a comprehensive refer-

ence source. To complement the infor-

mation in this data sheet, refer to Section

5. “Flash Programming” (DS70191) in

the “dsPIC33F/PIC24H Family

Reference Manual”, which is available

from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Program Counter

24 bits

Program Counter

TBLPAG Reg

8 bits

Working Reg EA

16 bits

Byte

24-bit EA

1/0

Select

Using

Table Instruction

Using

User/Configuration

Space Select

dsPIC33FJXXXGPX06A/X08A/X10A

5.2 RTSP Operation

The dsPIC33FJXXXGPX06A/X08A/X10A Flash pro-

gram memory array is organized into rows of 64

instructions or 192 bytes. RTSP allows the user to

erase a page of memory, which consists of eight rows

(512 instructions) at a time, and to program one row or

one word at a time. Table 25-12 illustrates typical erase

and programming times. The 8-row erase pages and

single row write rows are edge-aligned, from the begin-

ning of program memory, on boundaries of 1536 bytes

and 192 bytes, respectively.

The program memory implements holding buffers that

can contain 64 instructions of programming data. Prior

to the actual programming operation, the write data

must be loaded into the buffers in sequential order. The

instruction words loaded must always be from a group

of 64 boundary.

The basic sequence for RTSP programming is to set up

a Table Pointer, then do a series of TBLWT instructions

to load the buffers. Programming is performed by

setting the control bits in the NVMCON register. A total

of 64 TBLWTL and TBLWTH instructions are required

to load the instructions.

All of the table write operations are single-word writes

(two instruction cycles) because only the buffers are

written. A programming cycle is required for

programming each row.

5.3 Programming Operations

A complete programming sequence is necessary for

programming or erasing the internal Flash in RTSP

mode. The processor stalls (waits) until the

programming operation is finished.

The programming time depends on the FRC accuracy

(see Table 25-19) and the value of the FRC Oscillator

Tuning register (see Register 9-4). Use the following

formula to calculate the minimum and maximum values

for the Row Write Time, Page Erase Time and Word

Write Cycle Time parameters (see Table 25-12).

EQUATION 5-1: PROGRAMMING TIME

For example, if the device is operating at +125°C, the

FRC accuracy will be ±5%. If the TUN<5:0> bits (see

write time is equal to Equation 5-2.

EQUATION 5-2: MINIMUM ROW WRITE

TIME

The maximum row write time is equal to Equation 5-3.

EQUATION 5-3: MAXIMUM ROW WRITE

TIME

Setting the WR bit (NVMCON<15>) starts the

operation, and the WR bit is automatically cleared

when the operation is finished.

5.4 Control Registers

The two SFRs that are used to read and write the

program Flash memory are:

•NVMCON: Flash Memory Control Register

•NVMKEY: Non-Volatile Memory Key Register

The NVMCON register (Register 5-1) controls which

blocks are to be erased, which memory type is to be

programmed and the start of the programming cycle.

NVMKEY (Register 5-2) is a write-only register that is

used for write protection. To start a programming or

erase sequence, the user must consecutively write 0x55

and 0xAA to the NVMKEY register. Refer to Section 5.3

“Programming Operations” for further details.

7.37 MHz FRC Accuracy()%FRC Tuning()%××

----------------------------------------------------------------------------------------------------------------------------

TRW

11064 Cycles

7.37 MHz 10.05+()1 0.00375–()××

------------------------------------------------------------------------------------------------ 1.435ms==

TRW

11064 Cycles

7.37 MHz 10.05–()1 0.00375–()××

------------------------------------------------------------------------------------------------1.586ms==

dsPIC33FJXXXGPX06A/X08A/X10A

R/SO-0(1) R/W-0(1) R/W-0(1) U-0 U-0 U-0 U-0 U-0

WR WREN WRERR — — — — —

bit 15 bit 8

U-0 R/W-0(1) U-0 U-0 R/W-0(1) R/W-0(1) R/W-0(1) R/W-0(1)

— ERASE ——NVMOP<3:0>

(2)

bit 7 bit 0

Legend: SO = Settable only bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 WR: Write Control bit

1 = Initiates a Flash memory program or erase operation. The operation is self-timed and the bit is

cleared by hardware once operation is complete

0 = Program or erase operation is complete and inactive

bit 14 WREN: Write Enable bit

1 = Enable Flash program/erase operations

0 = Inhibit Flash program/erase operations

bit 13 WRERR: Write Sequence Error Flag bit

1 = An improper program or erase sequence attempt or termination has occurred (bit is set

automatically on any set attempt of the WR bit)

0 = The program or erase operation completed normally

bit 12-7 Unimplemented: Read as ‘0’

bit 6 ERASE: Erase/Program Enable bit

1 = Perform the erase operation specified by NVMOP<3:0> on the next WR command

0 = Perform the program operation specified by NVMOP<3:0> on the next WR command

bit 5-4 Unimplemented: Read as ‘0’

bit 3-0 NVMOP<3:0>: NVM Operation Select bits(2)

If ERASE = 1:

1111 = Memory bulk erase operation

1110 = Reserved

1101 = Erase General Segment

1100 = Erase Secure Segment

1011 = Reserved

0011 = No operation

0010 = Memory page erase operation

0001 = No operation

0000 = Erase a single Configuration register byte

If ERASE = 0:

1111 = No operation

1110 = Reserved

1101 = No operation

1100 = No operation

1011 = Reserved

0011 = Memory word program operation

0010 = No operation

0001 = Memory row program operation

0000 = Program a single Configuration register byte

Note 1: These bits can only be reset on POR.

2: All other combinations of NVMOP<3:0> are unimplemented.

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0

NVMKEY<7:0>

bit 7 bit 0

Legend: SO = Settable only bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7-0 NVMKEY<7:0>: Key Register (Write Only) bits

dsPIC33FJXXXGPX06A/X08A/X10A

5.4.1 PROGRAMMING ALGORITHM FOR

FLASH PROGRAM MEMORY

The user can program one row of program Flash

memory at a time. To do this, it is necessary to erase

the 8-row erase page that contains the desired row.

The general process is:

1. Read eight rows of program memory

(512 instructions) and store in data RAM.

2. Update the program data in RAM with the

desired new data.

3. Erase the block (see Example 5-1):

a) Set the NVMOP bits (NVMCON<3:0>) to

‘0010’ to configure for block erase. Set the

ERASE bit (NVMCON<6>) and the WREN

bit (NVMCON<14>).

b) Write the starting address of the page to be

erased into the TBLPAG and W registers.

c) Write 0x55 to NVMKEY.

d) Write 0xAA to NVMKEY.

e) Set the WR bit (NVMCON<15>). The erase

cycle begins and the CPU stalls for the

duration of the erase cycle. When the erase is

done, the WR bit is cleared automatically.

4. Write the first 64 instructions from data RAM into

the program memory buffers (see Example 5-2).

5. Write the program block to Flash memory:

a) Set the NVMOP bits to ‘0001’ to configure

for row programming. Clear the ERASE bit

and set the WREN bit.

b) Write 0x55 to NVMKEY.

c) Write 0xAA to NVMKEY.

d) Set the WR bit. The programming cycle

begins and the CPU stalls for the duration of

the write cycle. When the write to Flash

memory is done, the WR bit is cleared

automatically.

6. Repeat steps 4 and 5, using the next available

64 instructions from the block in data RAM by

incrementing the value in TBLPAG, until all

512 instructions are written back to Flash memory.

For protection against accidental operations, the write

initiate sequence for NVMKEY must be used to allow

any erase or program operation to proceed. After the

programming command has been executed, the user

must wait for the programming time until programming

is complete. The two instructions following the start of

the programming sequence should be NOPs, as shown

in Example 5-3.

EXAMPLE 5-1: ERASING A PROGRAM MEMORY PAGE

; Set up NVMCON for block erase operation

MOV #0x4042, W0 ;

MOV W0, NVMCON ; Initialize NVMCON

; Init pointer to row to be ERASED

MOV #tblpage(PROG_ADDR), W0 ;

MOV W0, TBLPAG ; Initialize PM Page Boundary SFR

MOV #tbloffset(PROG_ADDR), W0 ; Initialize in-page EA[15:0] pointer

TBLWTL W0, [W0] ; Set base address of erase block

DISI #5 ; Block all interrupts with priority <7

; for next 5 instructions

MOV #0x55, W0

MOV W0, NVMKEY ; Write the 55 key

MOV #0xAA, W1 ;

MOV W1, NVMKEY ; Write the AA key

BSET NVMCON, #WR ; Start the erase sequence

NOP ; Insert two NOPs after the erase

NOP ; command is asserted

dsPIC33FJXXXGPX06A/X08A/X10A

EXAMPLE 5-2: LOADING THE WRITE BUFFERS

EXAMPLE 5-3: INITIATING A PROGRAMMING SEQUENCE

; Set up NVMCON for row programming operations

MOV #0x4001, W0 ;

MOV W0, NVMCON ; Initialize NVMCON

; Set up a pointer to the first program memory location to be written

; program memory selected, and writes enabled

MOV #0x0000, W0 ;

MOV W0, TBLPAG ; Initialize PM Page Boundary SFR

MOV #0x6000, W0 ; An example program memory address

; Perform the TBLWT instructions to write the latches

; 0th_program_word

MOV #LOW_WORD_0, W2 ;

MOV #HIGH_BYTE_0, W3 ;

TBLWTL W2, [W0] ; Write PM low word into program latch

TBLWTH W3, [W0++] ; Write PM high byte into program latch

; 1st_program_word

MOV #LOW_WORD_1, W2 ;

MOV #HIGH_BYTE_1, W3 ;

TBLWTL W2, [W0] ; Write PM low word into program latch

TBLWTH W3, [W0++] ; Write PM high byte into program latch

; 2nd_program_word

MOV #LOW_WORD_2, W2 ;

MOV #HIGH_BYTE_2, W3 ;

TBLWTL W2, [W0] ; Write PM low word into program latch

TBLWTH W3, [W0++] ; Write PM high byte into program latch

•

; 63rd_program_word

MOV #LOW_WORD_31, W2 ;

MOV #HIGH_BYTE_31, W3 ;

TBLWTL W2, [W0] ; Write PM low word into program latch

TBLWTH W3, [W0++] ; Write PM high byte into program latch

DISI #5 ; Block all interrupts with priority <7

; for next 5 instructions

MOV #0x55, W0

MOV W0, NVMKEY ; Write the 55 key

MOV #0xAA, W1 ;

MOV W1, NVMKEY ; Write the AA key

BSET NVMCON, #WR ; Start the erase sequence

NOP ; Insert two NOPs after the

NOP ; erase command is asserted

dsPIC33FJXXXGPX06A/X08A/X10A

6.0 RESET

The Reset module combines all Reset sources and

controls the device Master Reset Signal, SYSRST. The

following is a list of device Reset sources:

• POR: Power-on Reset

• BOR: Brown-out Reset

•MCLR

: Master Clear Pin Reset

•SWR: RESET Instruction

• WDT: Watchdog Timer Reset

• TRAPR: Trap Conflict Reset

• IOPUWR: Illegal Opcode and Uninitialized W

A simplified block diagram of the Reset module is

shown in Figure 6-1.

Any active source of Reset will make the SYSRST

signal active. Many registers associated with the CPU

and peripherals are forced to a known Reset state.

Most registers are unaffected by a Reset; their status is

unknown on POR and unchanged by all other Resets.

All types of device Reset will set a corresponding status

bit in the RCON register to indicate the type of Reset

(see Register 6-1). A POR will clear all bits, except for

the POR bit (RCON<0>), that are set. The user can set

or clear any bit at any time during code execution. The

RCON bits only serve as status bits. Setting a particular

Reset status bit in software does not cause a device

Reset to occur.

The RCON register also has other bits associated with

the Watchdog Timer and device power-saving states.

The function of these bits is discussed in other sections

of this manual.

FIGURE 6-1: RESET SYSTEM BLOCK DIAGRAM

Note 1: This data sheet summarizes the features

of the dsPIC33FJXXXGPX06A/X08A/

X10A family of devices. However, it is not

intended to be a comprehensive refer-

ence source. To complement the infor-

mation in this data sheet, refer to Section

8. “Reset” (DS70192) in the “dsPIC33F/

PIC24H Family Reference Manual”,

which is available from the Microchip web

site (www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Note: Refer to the specific peripheral or CPU

section of this manual for register Reset

states.

Note: The status bits in the RCON register

should be cleared after they are read so

that the next RCON register value after a

device Reset will be meaningful.

MCLR

VDD

Internal

Regulator

BOR

Sleep or Idle

RESET Instruction

WDT

Module

Glitch Filter

Trap Conflict

Illegal Opcode

Uninitialized W Register

SYSRST

VDD Rise

Detect

POR

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 U-0 U-0 U-0 U-0 U-0 R/W-0

TRAPR IOPUWR — — — — —VREGS

(3)

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-1 R/W-1

EXTR SWR SWDTEN(2) WDTO SLEEP IDLE BOR POR

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 TRAPR: Trap Reset Flag bit

1 = A Trap Conflict Reset has occurred

0 = A Trap Conflict Reset has not occurred

bit 14 IOPUWR: Illegal Opcode or Uninitialized W Access Reset Flag bit

1 = An illegal opcode detection, an illegal address mode or uninitialized W register used as an

Address Pointer caused a Reset

0 = An illegal opcode or uninitialized W Reset has not occurred

bit 13-9 Unimplemented: Read as ‘0’

bit 8 VREGS: Voltage Regulator Standby During Sleep bit(3)

1 = Voltage Regulator is active during Sleep mode

0 = Voltage Regulator goes into standby mode during Sleep

bit 7 EXTR: External Reset (MCLR) Pin bit

1 = A Master Clear (pin) Reset has occurred

0 = A Master Clear (pin) Reset has not occurred

bit 6 SWR: Software Reset (Instruction) Flag bit

1 = A RESET instruction has been executed

0 = A RESET instruction has not been executed

bit 5 SWDTEN: Software Enable/Disable of WDT bit(2)

1 = WDT is enabled

0 = WDT is disabled

bit 4 WDTO: Watchdog Timer Time-out Flag bit

1 = WDT time-out has occurred

0 = WDT time-out has not occurred

bit 3 SLEEP: Wake-up from Sleep Flag bit

1 = Device has been in Sleep mode

0 = Device has not been in Sleep mode

bit 2 IDLE: Wake-up from Idle Flag bit

1 = Device was in Idle mode

0 = Device was not in Idle mode

bit 1 BOR: Brown-out Reset Flag bit

1 = A Brown-out Reset has occurred

0 = A Brown-out Reset has not occurred

Note 1: All of the Reset status bits may be set or cleared in software. Setting one of these bits in software does not

cause a device Reset.

2: If the FWDTEN Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled, regardless of the

SWDTEN bit setting.

3: For dsPIC33FJ256GPX06A/X08A/X10A devices, this bit is unimplemented and reads back programmed

value.

dsPIC33FJXXXGPX06A/X08A/X10A

bit 0 POR: Power-on Reset Flag bit

1 = A Power-on Reset has occurred

0 = A Power-on Reset has not occurred

Note 1: All of the Reset status bits may be set or cleared in software. Setting one of these bits in software does not

cause a device Reset.

2: If the FWDTEN Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled, regardless of the

SWDTEN bit setting.

3: For dsPIC33FJ256GPX06A/X08A/X10A devices, this bit is unimplemented and reads back programmed

value.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 6-1: RESET FLAG BIT OPERATION

6.1 Clock Source Selection at Reset

If clock switching is enabled, the system clock source at

device Reset is chosen, as shown in Table 6-2. If clock

switching is disabled, the system clock source is always

selected according to the oscillator Configuration bits.

Refer to Section 9.0 “Oscillator Configuration” for

further details.

TABLE 6-2: OSCILLATOR SELECTION VS

TYPE OF RESET (CLOCK

SWITCHING ENABLED)

6.2 Device Reset Times

The Reset times for various types of device Reset are

summarized in Table 6- 3 . The system Reset signal,

SYSRST, is released after the POR and PWRT delay

times expire.

The time at which the device actually begins to execute

code also depends on the system oscillator delays,

which include the Oscillator Start-up Timer (OST) and

the PLL lock time. The OST and PLL lock times occur

in parallel with the applicable SYSRST delay times.

The FSCM delay determines the time at which the

FSCM begins to monitor the system clock source after

the SYSRST signal is released.

Flag Bit Setting Event Clearing Event

TRAPR (RCON<15>) Trap conflict event POR, BOR

IOPUWR (RCON<14>) Illegal opcode or uninitialized

W register access

POR, BOR

EXTR (RCON<7>) MCLR Reset POR

SWR (RCON<6>) RESET instruction POR, BOR

WDTO (RCON<4>) WDT time-out PWRSAV instruction, POR, BOR

SLEEP (RCON<3>) PWRSAV #SLEEP instruction POR, BOR

IDLE (RCON<2>) PWRSAV #IDLE instruction POR, BOR

BOR (RCON<1>) BOR, POR —

POR (RCON<0>) POR —

Note: All Reset flag bits may be set or cleared by the user software.

Reset Type Clock Source Determinant

POR Oscillator Configuration bits

(FNOSC<2:0>)

BOR

MCLR COSC Control bits

(OSCCON<14:12>)

WDTR

SWR

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 6-3: RESET DELAY TIMES FOR VARIOUS DEVICE RESETS

6.2.1 POR AND LONG OSCILLATOR

START-UP TIMES

The oscillator start-up circuitry and its associated delay

timers are not linked to the device Reset delays that

occur at power-up. Some crystal circuits (especially

low-frequency crystals) have a relatively long start-up

time. Therefore, one or more of the following conditions

is possible after SYSRST is released:

• The oscillator circuit has not begun to oscillate.

• The Oscillator Start-up Timer has not expired (if a

crystal oscillator is used).

• The PLL has not achieved a lock (if PLL is used).

The device will not begin to execute code until a valid

clock source has been released to the system.

Therefore, the oscillator and PLL start-up delays must

be considered when the Reset delay time must be

known.

6.2.2 FAIL-SAFE CLOCK MONITOR

(FSCM) AND DEVICE RESETS

If the FSCM is enabled, it begins to monitor the system

clock source when SYSRST is released. If a valid clock

source is not available at this time, the device

automatically switches to the FRC oscillator and the

user can switch to the desired crystal oscillator in the

Trap Service Routine.

6.2.2.1 FSCM Delay for Crystal and PLL

Clock Sources

When the system clock source is provided by a crystal

oscillator and/or the PLL, a small delay, TFSCM, is auto-

matically inserted after the POR and PWRT delay

times. The FSCM does not begin to monitor the system

clock source until this delay expires. The FSCM delay

time is nominally 500 μs and provides additional time

for the oscillator and/or PLL to stabilize. In most cases,

the FSCM delay prevents an oscillator failure trap at a

device Reset when the PWRT is disabled.

6.3 Special Function Register Reset

States

Most of the Special Function Registers (SFRs) associ-

ated with the CPU and peripherals are reset to a

particular value at a device Reset. The SFRs are

grouped by their peripheral or CPU function and their

Reset values are specified in each section of this manual.

The Reset value for each SFR does not depend on the

type of Reset, with the exception of two registers. The

Reset value for the Reset Control register, RCON,

depends on the type of device Reset. The Reset value

for the Oscillator Control register, OSCCON, depends

on the type of Reset and the programmed values of the

oscillator Configuration bits in the FOSC Configuration

Reset Type Clock Source SYSRST Delay System Clock

Delay

FSCM

Delay See Notes

POR EC, FRC, LPRC TPOR + TSTARTUP + TRST ——1, 2, 3

ECPLL, FRCPLL TPOR + TSTARTUP + TRST TLOCK TFSCM 1, 2, 3, 5, 6

XT, HS, SOSC TPOR + TSTARTUP + TRST TOST TFSCM 1, 2, 3, 4, 6

XTPLL, HSPLL TPOR + TSTARTUP + TRST TOST + TLOCK TFSCM 1, 2, 3, 4, 5, 6

BOR EC, FRC, LPRC TSTARTUP + TRST ——3

ECPLL, FRCPLL TSTARTUP + TRST TLOCK TFSCM 3, 5, 6

XT, HS, SOSC TSTARTUP + TRST TOST TFSCM 3, 4, 6

XTPLL, HSPLL TSTARTUP + TRST TOST + TLOCK TFSCM 3, 4, 5, 6

MCLR Any Clock TRST ——3

WDT Any Clock TRST ——3

Software Any Clock TRST ——3

Illegal Opcode Any Clock TRST ——3

Uninitialized W Any Clock TRST ——3

Trap Conflict Any Clock TRST ——3

Note 1: TPOR = Power-on Reset delay (10 μs nominal).

2: TSTARTUP = Conditional POR delay of 20 μs nominal (if on-chip regulator is enabled) or 64 ms nominal

Power-up Timer delay (if regulator is disabled). TSTARTUP is also applied to all returns from powered-down

states, including waking from Sleep mode, only if the regulator is enabled.

3: TRST = Internal state Reset time (20 μs nominal).

4: TOST = Oscillator Start-up Timer. A 10-bit counter counts 1024 oscillator periods before releasing the

oscillator clock to the system.

5: TLOCK = PLL lock time (20 μs nominal).

6: TFSCM = Fail-Safe Clock Monitor delay (100 μs nominal).

dsPIC33FJXXXGPX06A/X08A/X10A

NOTES:

dsPIC33FJXXXGPX06A/X08A/X10A

7.0 INTERRUPT CONTROLLER

The dsPIC33FJXXXGPX06A/X08A/X10A interrupt

controller reduces the numerous peripheral interrupt

request signals to a single interrupt request signal to

the dsPIC33FJXXXGPX06A/X08A/X10A CPU. It has

the following features:

• Up to eight processor exceptions and software

traps

• Seven user-selectable priority levels

• Interrupt Vector Table (IVT) with up to 118 vectors

• A unique vector for each interrupt or exception

source

• Fixed priority within a specified user priority level

• Alternate Interrupt Vector Table (AIVT) for debug

support

• Fixed interrupt entry and return latencies

7.1 Interrupt Vector Table

The Interrupt Vector Table is shown in Figure 7-1. The

IVT resides in program memory, starting at location

000004h. The IVT contains 126 vectors consisting of

eight non-maskable trap vectors plus up to 118 sources

of interrupt. In general, each interrupt source has its

own vector. Each interrupt vector contains a 24-bit wide

address. The value programmed into each interrupt

vector location is the starting address of the associated

Interrupt Service Routine (ISR).

Interrupt vectors are prioritized in terms of their natural

priority; this priority is linked to their position in the

vector table. All other things being equal, lower

addresses have a higher natural priority. For example,

the interrupt associated with vector 0 will take priority

over interrupts at any other vector address.

dsPIC33FJXXXGPX06A/X08A/X10A devices imple-

ment up to 67 unique interrupts and five non-maskable

traps. These are summarized in Ta b l e 7 - 1 and

Table 7-2.

7.1.1 ALTERNATE VECTOR TABLE

The Alternate Interrupt Vector Table (AIVT) is located

after the IVT, as shown in Figure 7-1. Access to the

AIVT is provided by the ALTIVT control bit

(INTCON2<15>). If the ALTIVT bit is set, all interrupt

and exception processes use the alternate vectors

instead of the default vectors. The alternate vectors are

organized in the same manner as the default vectors.

The AIVT supports debugging by providing a means to

switch between an application and a support

environment without requiring the interrupt vectors to

be reprogrammed. This feature also enables switching

between applications for evaluation of different

software algorithms at run time. If the AIVT is not

needed, the AIVT should be programmed with the

same addresses used in the IVT.

7.2 Reset Sequence

A device Reset is not a true exception because the

interrupt controller is not involved in the Reset process.

The dsPIC33FJXXXGPX06A/X08A/X10A device

clears its registers in response to a Reset, which forces

the PC to zero. The digital signal controller then begins

program execution at location 0x000000. The user

programs a GOTO instruction at the Reset address

which redirects program execution to the appropriate

start-up routine.

Note 1: This data sheet summarizes the features

of the dsPIC33FJXXXGPX06A/X08A/

X10A family of devices. However, it is not

intended to be a comprehensive

reference source. To complement the

information in this data sheet, refer to

Section 6. “Interrupts” (DS70184) in

the “dsPIC33F/PIC24H Family

Reference Manual”, which is available

from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Note: Any unimplemented or unused vector

locations in the IVT and AIVT should be

programmed with the address of a default

interrupt handler routine that contains a

RESET instruction.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 7-1: dsPIC33FJXXXGPX06A/X08A/X10A INTERRUPT VECTOR TABLE

Reset – GOTO Instruction 0x000000

Reset – GOTO Address 0x000002

Reserved 0x000004

Oscillator Fail Trap Vector

Address Error Trap Vector

Stack Error Trap Vector

Math Error Trap Vector

DMA Error Trap Vector

Reserved

Interrupt Vector 0 0x000014

Interrupt Vector 1

Interrupt Vector 52 0x00007C

Interrupt Vector 53 0x00007E

Interrupt Vector 54 0x000080

Interrupt Vector 116 0x0000FC

Interrupt Vector 117 0x0000FE

Reserved 0x000100

Reserved 0x000102

Reserved

Oscillator Fail Trap Vector

Address Error Trap Vector

Stack Error Trap Vector

Math Error Trap Vector

DMA Error Trap Vector

Reserved

Interrupt Vector 0 0x000114

Interrupt Vector 1

Interrupt Vector 52 0x00017C

Interrupt Vector 53 0x00017E

Interrupt Vector 54 0x000180

Interrupt Vector 116

Interrupt Vector 117 0x0001FE

Start of Code 0x000200

Decreasing Natural Order Priority

Interrupt Vector Table (IVT)(1)

Alternate Interrupt Vector Table (AIVT)(1)

Note 1: See Table 7-1 for the list of implemented interrupt vectors.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 7-1: INTERRUPT VECTORS

Vector

Number

Interrupt

Request (IRQ)

Number

IVT Address AIVT Address Interrupt Source

8 0 0x000014 0x000114 INT0 – External Interrupt 0

9 1 0x000016 0x000116 IC1 – Input Capture 1

10 2 0x000018 0x000118 OC1 – Output Compare 1

11 3 0x00001A 0x00011A T1 – Timer1

12 4 0x00001C 0x00011C DMA0 – DMA Channel 0

13 5 0x00001E 0x00011E IC2 – Input Capture 2

14 6 0x000020 0x000120 OC2 – Output Compare 2

15 7 0x000022 0x000122 T2 – Timer2

16 8 0x000024 0x000124 T3 – Timer3

17 9 0x000026 0x000126 SPI1E – SPI1 Error

18 10 0x000028 0x000128 SPI1 – SPI1 Transfer Done

19 11 0x00002A 0x00012A U1RX – UART1 Receiver

20 12 0x00002C 0x00012C U1TX – UART1 Transmitter

21 13 0x00002E 0x00012E ADC1 – ADC 1

22 14 0x000030 0x000130 DMA1 – DMA Channel 1

23 15 0x000032 0x000132 Reserved

24 16 0x000034 0x000134 SI2C1 – I2C1 Slave Events

25 17 0x000036 0x000136 MI2C1 – I2C1 Master Events

26 18 0x000038 0x000138 Reserved

27 19 0x00003A 0x00013A Change Notification Interrupt

28 20 0x00003C 0x00013C INT1 – External Interrupt 1

29 21 0x00003E 0x00013E ADC2 – ADC 2

30 22 0x000040 0x000140 IC7 – Input Capture 7

31 23 0x000042 0x000142 IC8 – Input Capture 8

32 24 0x000044 0x000144 DMA2 – DMA Channel 2

33 25 0x000046 0x000146 OC3 – Output Compare 3

34 26 0x000048 0x000148 OC4 – Output Compare 4

35 27 0x00004A 0x00014A T4 – Timer4

36 28 0x00004C 0x00014C T5 – Timer5

37 29 0x00004E 0x00014E INT2 – External Interrupt 2

38 30 0x000050 0x000150 U2RX – UART2 Receiver

39 31 0x000052 0x000152 U2TX – UART2 Transmitter

40 32 0x000054 0x000154 SPI2E – SPI2 Error

41 33 0x000056 0x000156 SPI1 – SPI1 Transfer Done

42 34 0x000058 0x000158 C1RX – ECAN1 Receive Data Ready

43 35 0x00005A 0x00015A C1 – ECAN1 Event

44 36 0x00005C 0x00015C DMA3 – DMA Channel 3

45 37 0x00005E 0x00015E IC3 – Input Capture 3

46 38 0x000060 0x000160 IC4 – Input Capture 4

47 39 0x000062 0x000162 IC5 – Input Capture 5

48 40 0x000064 0x000164 IC6 – Input Capture 6

49 41 0x000066 0x000166 OC5 – Output Compare 5

50 42 0x000068 0x000168 OC6 – Output Compare 6

51 43 0x00006A 0x00016A OC7 – Output Compare 7

52 44 0x00006C 0x00016C OC8 – Output Compare 8

53 45 0x00006E 0x00016E Reserved

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 7-2: TRAP VECTORS

54 46 0x000070 0x000170 DMA4 – DMA Channel 4

55 47 0x000072 0x000172 T6 – Timer6

56 48 0x000074 0x000174 T7 – Timer7

57 49 0x000076 0x000176 SI2C2 – I2C2 Slave Events

58 50 0x000078 0x000178 MI2C2 – I2C2 Master Events

59 51 0x00007A 0x00017A T8 – Timer8

60 52 0x00007C 0x00017C T9 – Timer9

61 53 0x00007E 0x00017E INT3 – External Interrupt 3

62 54 0x000080 0x000180 INT4 – External Interrupt 4

63 55 0x000082 0x000182 C2RX – ECAN2 Receive Data Ready

64 56 0x000084 0x000184 C2 – ECAN2 Event

65 57 0x000086 0x000186 Reserved

66 58 0x000088 0x000188 Reserved

67 59 0x00008A 0x00018A DCIE – DCI Error

68 60 0x00008C 0x00018C DCID – DCI Transfer Done

69 61 0x00008E 0x00018E DMA5 – DMA Channel 5

70 62 0x000090 0x000190 Reserved

71 63 0x000092 0x000192 Reserved

72 64 0x000094 0x000194 Reserved

73 65 0x000096 0x000196 U1E – UART1 Error

74 66 0x000098 0x000198 U2E – UART2 Error

75 67 0x00009A 0x00019A Reserved

76 68 0x00009C 0x00019C DMA6 – DMA Channel 6

77 69 0x00009E 0x00019E DMA7 – DMA Channel 7

78 70 0x0000A0 0x0001A0 C1TX – ECAN1 Transmit Data Request

79 71 0x0000A2 0x0001A2 C2TX – ECAN2 Transmit Data Request

80-125 72-117 0x0000A4-0x0000FE 0x0001A4-0x0001FE Reserved

Vector Number IVT Address AIVT Address Trap Source

0 0x000004 0x000104 Reserved

1 0x000006 0x000106 Oscillator Failure

2 0x000008 0x000108 Address Error

3 0x00000A 0x00010A Stack Error

4 0x00000C 0x00010C Math Error

5 0x00000E 0x00010E DMA Error Trap

6 0x000010 0x000110 Reserved

7 0x000012 0x000112 Reserved

TABLE 7-1: INTERRUPT VECTORS (CONTINUED)

Vector

Number

Interrupt

Request (IRQ)

Number

IVT Address AIVT Address Interrupt Source

dsPIC33FJXXXGPX06A/X08A/X10A

7.3 Interrupt Control and Status

Registers

dsPIC33FJXXXGPX06A/X08A/X10A devices imple-

ment a total of 30 registers for the interrupt controller:

• INTCON1

• INTCON2

• IFS0 through IFS4

• IEC0 through IEC4

• IPC0 through IPC17

•INTTREG

Global interrupt control functions are controlled from

INTCON1 and INTCON2. INTCON1 contains the

Interrupt Nesting Disable (NSTDIS) bit as well as the

control and status flags for the processor trap sources.

The INTCON2 register controls the external interrupt

request signal behavior and the use of the Alternate

Interrupt Vector Table.

The IFS registers maintain all of the interrupt request

flags. Each source of interrupt has a Status bit, which is

set by the respective peripherals or external signal and

is cleared via software.

The IEC registers maintain all of the interrupt enable

bits. These control bits are used to individually enable

interrupts from the peripherals or external signals.

The IPC registers are used to set the interrupt priority

level for each source of interrupt. Each user interrupt

source can be assigned to one of eight priority levels.

The INTTREG register contains the associated

interrupt vector number and the new CPU interrupt

priority level, which are latched into vector number

(VECNUM<6:0>) and Interrupt level bits (ILR<3:0>) in

the INTTREG register. The new interrupt priority level

is the priority of the pending interrupt.

The interrupt sources are assigned to the IFSx, IECx

and IPCx registers in the same sequence that they are

listed in Ta b l e 7 - 1 . For example, the INT0 (External

Interrupt 0) is shown as having vector number 8 and a

natural order priority of 0. Thus, the INT0IF bit is found

in IFS0<0>, the INT0IE bit in IEC0<0>, and the INT0IP

bits in the first position of IPC0 (IPC0<2:0>).

Although they are not specifically part of the interrupt

control hardware, two of the CPU Control registers

contain bits that control interrupt functionality. The CPU

STATUS register, SR, contains the IPL<2:0> bits

(SR<7:5>). These bits indicate the current CPU

interrupt priority level. The user can change the current

CPU priority level by writing to the IPL bits.

The CORCON register contains the IPL3 bit which,

together with IPL<2:0>, also indicates the current CPU

priority level. IPL3 is a read-only bit so that trap events

cannot be masked by the user software.

All Interrupt registers are described in Register 7-1

through Register 7-32.

dsPIC33FJXXXGPX06A/X08A/X10A

R-0 R-0 R/C-0 R/C-0 R-0 R/C-0 R -0 R/W-0

OA OB SA SB OAB SAB DA DC

bit 15 bit 8

R/W-0(3) R/W-0(3) R/W-0(3) R-0 R/W-0 R/W-0 R/W-0 R/W-0

IPL2(2) IPL1(2) IPL0(2) RA N OV Z C

bit 7 bit 0

Legend:

C = Clear only bit R = Readable bit U = Unimplemented bit, read as ‘0’

S = Set only bit W = Writable bit -n = Value at POR

‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 7-5 IPL<2:0>: CPU Interrupt Priority Level Status bits(2)

111 = CPU Interrupt Priority Level is 7 (15), user interrupts disabled

110 = CPU Interrupt Priority Level is 6 (14)

101 = CPU Interrupt Priority Level is 5 (13)

100 = CPU Interrupt Priority Level is 4 (12)

011 = CPU Interrupt Priority Level is 3 (11)

010 = CPU Interrupt Priority Level is 2 (10)

001 = CPU Interrupt Priority Level is 1 (9)

000 = CPU Interrupt Priority Level is 0 (8)

Note 1: For complete register details, see Register 3-1.

2: The IPL<2:0> bits are concatenated with the IPL<3> bit (CORCON<3>) to form the CPU Interrupt Priority

Level. The value in parentheses indicates the IPL if IPL<3> = 1. User interrupts are disabled when

IPL<3> = 1.

3: The IPL<2:0> Status bits are read-only when NSTDIS (INTCON1<15>) = 1.

U-0 U-0 U-0 R/W-0 R/W-0 R-0 R-0 R-0

— — —USEDT DL<2:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-1 R/W-0 R/C-0 R/W-0 R/W-0 R/W-0

SATA SATB SATDW ACCSAT IPL3(2) PSV RND IF

bit 7 bit 0

Legend: C = Clear only bit

R = Readable bit W = Writable bit -n = Value at POR ‘1’ = Bit is set

0’ = Bit is cleared ‘x = Bit is unknown U = Unimplemented bit, read as ‘0’

bit 3 IPL3: CPU Interrupt Priority Level Status bit 3(2)

1 = CPU interrupt priority level is greater than 7

0 = CPU interrupt priority level is 7 or less

Note 1: For complete register details, see Register 3-2.

2: The IPL3 bit is concatenated with the IPL<2:0> bits (SR<7:5>) to form the CPU Interrupt Priority Level.

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

NSTDIS OVAERR OVBERR COVAERR COVBERR OVATE OVBTE COVTE

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0

SFTACERR DIV0ERR DMACERR MATHERR ADDRERR STKERR OSCFAIL —

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 NSTDIS: Interrupt Nesting Disable bit

1 = Interrupt nesting is disabled

0 = Interrupt nesting is enabled

bit 14 OVAERR: Accumulator A Overflow Trap Flag bit

1 = Trap was caused by overflow of Accumulator A

0 = Trap was not caused by overflow of Accumulator A

bit 13 OVBERR: Accumulator B Overflow Trap Flag bit

1 = Trap was caused by overflow of Accumulator B

0 = Trap was not caused by overflow of Accumulator B

bit 12 COVAERR: Accumulator A Catastrophic Overflow Trap Flag bit

1 = Trap was caused by catastrophic overflow of Accumulator A

0 = Trap was not caused by catastrophic overflow of Accumulator A

bit 11 COVBERR: Accumulator B Catastrophic Overflow Trap Flag bit

1 = Trap was caused by catastrophic overflow of Accumulator B

0 = Trap was not caused by catastrophic overflow of Accumulator B

bit 10 OVATE: Accumulator A Overflow Trap Enable bit

1 = Trap overflow of Accumulator A

0 = Trap disabled

bit 9 OVBTE: Accumulator B Overflow Trap Enable bit

1 = Trap overflow of Accumulator B

0 = Trap disabled

bit 8 COVTE: Catastrophic Overflow Trap Enable bit

1 = Trap on catastrophic overflow of Accumulator A or B enabled

0 = Trap disabled

bit 7 SFTACERR: Shift Accumulator Error Status bit

1 = Math error trap was caused by an invalid accumulator shift

0 = Math error trap was not caused by an invalid accumulator shift

bit 6 DIV0ERR: Arithmetic Error Status bit

1 = Math error trap was caused by a divide by zero

0 = Math error trap was not caused by a divide by zero

bit 5 DMACERR: DMA Controller Error Status bit

1 = DMA controller error trap has occurred

0 = DMA controller error trap has not occurred

bit 4 MATHERR: Arithmetic Error Status bit

1 = Math error trap has occurred

0 = Math error trap has not occurred

dsPIC33FJXXXGPX06A/X08A/X10A

bit 3 ADDRERR: Address Error Trap Status bit

1 = Address error trap has occurred

0 = Address error trap has not occurred

bit 2 STKERR: Stack Error Trap Status bit

1 = Stack error trap has occurred

0 = Stack error trap has not occurred

bit 1 OSCFAIL: Oscillator Failure Trap Status bit

1 = Oscillator failure trap has occurred

0 = Oscillator failure trap has not occurred

bit 0 Unimplemented: Read as ‘0’

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R-0 U-0 U-0 U-0 U-0 U-0 U-0

ALTIVT DISI — — — — — —

bit 15 bit 8

U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— — — INT4EP INT3EP INT2EP INT1EP INT0EP

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 ALTIVT: Enable Alternate Interrupt Vector Table bit

1 = Use alternate vector table

0 = Use standard (default) vector table

bit 14 DISI: DISI Instruction Status bit

1 = DISI instruction is active

0 = DISI instruction is not active

bit 13-5 Unimplemented: Read as ‘0’

bit 4 INT4EP: External Interrupt 4 Edge Detect Polarity Select bit

1 = Interrupt on negative edge

0 = Interrupt on positive edge

bit 3 INT3EP: External Interrupt 3 Edge Detect Polarity Select bit

1 = Interrupt on negative edge

0 = Interrupt on positive edge

bit 2 INT2EP: External Interrupt 2 Edge Detect Polarity Select bit

1 = Interrupt on negative edge

0 = Interrupt on positive edge

bit 1 INT1EP: External Interrupt 1 Edge Detect Polarity Select bit

1 = Interrupt on negative edge

0 = Interrupt on positive edge

bit 0 INT0EP: External Interrupt 0 Edge Detect Polarity Select bit

1 = Interrupt on negative edge

0 = Interrupt on positive edge

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— DMA1IF AD1IF U1TXIF U1RXIF SPI1IF SPI1EIF T3IF

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

T2IF OC2IF IC2IF DMA01IF T1IF OC1IF IC1IF INT0IF

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14 DMA1IF: DMA Channel 1 Data Transfer Complete Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 13 AD1IF: ADC1 Conversion Complete Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 12 U1TXIF: UART1 Transmitter Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 11 U1RXIF: UART1 Receiver Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 10 SPI1IF: SPI1 Event Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 9 SPI1EIF: SPI1 Fault Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 8 T3IF: Timer3 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 7 T2IF: Timer2 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 6 OC2IF: Output Compare Channel 2 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 5 IC2IF: Input Capture Channel 2 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 4 DMA01IF: DMA Channel 0 Data Transfer Complete Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 3 T1IF: Timer1 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

dsPIC33FJXXXGPX06A/X08A/X10A

bit 2 OC1IF: Output Compare Channel 1 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 1 IC1IF: Input Capture Channel 1 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 0 INT0IF: External Interrupt 0 Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

U2TXIF U2RXIF INT2IF T5IF T4IF OC4IF OC3IF DMA21IF

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0

IC8IF IC7IF AD2IF INT1IF CNIF —MI2C1IFSI2C1IF

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 U2TXIF: UART2 Transmitter Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 14 U2RXIF: UART2 Receiver Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 13 INT2IF: External Interrupt 2 Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 12 T5IF: Timer5 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 11 T4IF: Timer4 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 10 OC4IF: Output Compare Channel 4 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 9 OC3IF: Output Compare Channel 3 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 8 DMA21IF: DMA Channel 2 Data Transfer Complete Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 7 IC8IF: Input Capture Channel 8 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 6 IC7IF: Input Capture Channel 7 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 5 AD2IF: ADC2 Conversion Complete Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 4 INT1IF: External Interrupt 1 Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

dsPIC33FJXXXGPX06A/X08A/X10A

bit 3 CNIF: Input Change Notification Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 2 Unimplemented: Read as ‘0’

bit 1 MI2C1IF: I2C1 Master Events Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 0 SI2C1IF: I2C1 Slave Events Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

T6IF DMA4IF — OC8IF OC7IF OC6IF OC5IF IC6IF

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

IC5IF IC4IF IC3IF DMA3IF C1IF C1RXIF SPI2IF SPI2EIF

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 T6IF: Timer6 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 14 DMA4IF: DMA Channel 4 Data Transfer Complete Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 13 Unimplemented: Read as ‘0’

bit 12 OC8IF: Output Compare Channel 8 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 11 OC7IF: Output Compare Channel 7 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 10 OC6IF: Output Compare Channel 6 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 9 OC5IF: Output Compare Channel 5 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 8 IC6IF: Input Capture Channel 6 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 7 IC5IF: Input Capture Channel 5 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 6 IC4IF: Input Capture Channel 4 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 5 IC3IF: Input Capture Channel 3 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 4 DMA3IF: DMA Channel 3 Data Transfer Complete Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 3 C1IF: ECAN1 Event Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

dsPIC33FJXXXGPX06A/X08A/X10A

bit 2 C1RXIF: ECAN1 Receive Data Ready Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 1 SPI2IF: SPI2 Event Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 0 SPI2EIF: SPI2 Error Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 R/W-0 R/W-0 R/W-0 U-0 U-0 R/W-0

—— DMA5IF DCIIF DCIEIF ——C2IF

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

C2RXIF INT4IF INT3IF T9IF T8IF MI2C2IF SI2C2IF T7IF

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13 DMA5IF: DMA Channel 5 Data Transfer Complete Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 12 DCIIF: DCI Event Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 11 DCIEIF: DCI Error Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 10-9 Unimplemented: Read as ‘0’

bit 8 C2IF: ECAN2 Event Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 7 C2RXIF: ECAN2 Receive Data Ready Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 6 INT4IF: External Interrupt 4 Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 5 INT3IF: External Interrupt 3 Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 4 T9IF: Timer9 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 3 T8IF: Timer8 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 2 MI2C2IF: I2C2 Master Events Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 1 SI2C2IF: I2C2 Slave Events Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 0 T7IF: Timer7 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 U-0

C2TXIF C1TXIF DMA7IF DMA6IF —U2EIFU1EIF—

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7 C2TXIF: ECAN2 Transmit Data Request Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 6 C1TXIF: ECAN1 Transmit Data Request Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 5 DMA7IF: DMA Channel 7 Data Transfer Complete Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 4 DMA6IF: DMA Channel 6 Data Transfer Complete Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 3 Unimplemented: Read as ‘0’

bit 2 U2EIF: UART2 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 1 U1EIF: UART1 Interrupt Flag Status bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 0 Unimplemented: Read as ‘0’

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— DMA1IE AD1IE U1TXIE U1RXIE SPI1IE SPI1EIE T3IE

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

T2IE OC2IE IC2IE DMA0IE T1IE OC1IE IC1IE INT0IE

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14 DMA1IE: DMA Channel 1 Data Transfer Complete Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 13 AD1IE: ADC1 Conversion Complete Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 12 U1TXIE: UART1 Transmitter Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 11 U1RXIE: UART1 Receiver Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 10 SPI1IE: SPI1 Event Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 9 SPI1EIE: SPI1 Error Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 8 T3IE: Timer3 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 7 T2IE: Timer2 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 6 OC2IE: Output Compare Channel 2 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 5 IC2IE: Input Capture Channel 2 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 4 DMA0IE: DMA Channel 0 Data Transfer Complete Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 3 T1IE: Timer1 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

dsPIC33FJXXXGPX06A/X08A/X10A

bit 2 OC1IE: Output Compare Channel 1 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 1 IC1IE: Input Capture Channel 1 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 0 INT0IE: External Interrupt 0 Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

U2TXIE U2RXIE INT2IE T5IE T4IE OC4IE OC3IE DMA2IE

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0

IC8IE IC7IE AD2IE INT1IE CNIE —MI2C1IESI2C1IE

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 U2TXIE: UART2 Transmitter Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 14 U2RXIE: UART2 Receiver Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 13 INT2IE: External Interrupt 2 Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 12 T5IE: Timer5 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 11 T4IE: Timer4 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 10 OC4IE: Output Compare Channel 4 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 9 OC3IE: Output Compare Channel 3 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 8 DMA2IE: DMA Channel 2 Data Transfer Complete Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 7 IC8IE: Input Capture Channel 8 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 6 IC7IE: Input Capture Channel 7 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 5 AD2IE: ADC2 Conversion Complete Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 4 INT1IE: External Interrupt 1 Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

dsPIC33FJXXXGPX06A/X08A/X10A

bit 3 CNIE: Input Change Notification Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 2 Unimplemented: Read as ‘0’

bit 1 MI2C1IE: I2C1 Master Events Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 0 SI2C1IE: I2C1 Slave Events Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

T6IE DMA4IE — OC8IE OC7IE OC6IE OC5IE IC6IE

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

IC5IE IC4IE IC3IE DMA3IE C1IE C1RXIE SPI2IE SPI2EIE

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 T6IE: Timer6 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 14 DMA4IE: DMA Channel 4 Data Transfer Complete Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 13 Unimplemented: Read as ‘0’

bit 12 OC8IE: Output Compare Channel 8 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 11 OC7IE: Output Compare Channel 7 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 10 OC6IE: Output Compare Channel 6 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 9 OC5IE: Output Compare Channel 5 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 8 IC6IE: Input Capture Channel 6 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 7 IC5IE: Input Capture Channel 5 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 6 IC4IE: Input Capture Channel 4 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 5 IC3IE: Input Capture Channel 3 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 4 DMA3IE: DMA Channel 3 Data Transfer Complete Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 3 C1IE: ECAN1 Event Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

dsPIC33FJXXXGPX06A/X08A/X10A

bit 2 C1RXIE: ECAN1 Receive Data Ready Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 1 SPI2IE: SPI2 Event Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 0 SPI2EIE: SPI2 Error Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 R/W-0 R/W-0 R/W-0 U-0 U-0 R/W-0

—— DMA5IE DCIIE DCIEIE ——C2IE

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

C2RXIE INT4IE INT3IE T9IE T8IE MI2C2IE SI2C2IE T7IE

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13 DMA5IE: DMA Channel 5 Data Transfer Complete Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 12 DCIIE: DCI Event Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 11 DCIEIE: DCI Error Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 10-9 Unimplemented: Read as ‘0’

bit 8 C2IE: ECAN2 Event Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 7 C2RXIE: ECAN2 Receive Data Ready Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 6 INT4IE: External Interrupt 4 Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 5 INT3IE: External Interrupt 3 Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 4 T9IE: Timer9 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 3 T8IE: Timer8 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 2 MI2C2IE: I2C2 Master Events Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 1 SI2C2IE: I2C2 Slave Events Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 0 T7IE: Timer7 Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 U-0

C2TXIE C1TXIE DMA7IE DMA6IE —U2EIEU1EIE—

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7 C2TXIE: ECAN2 Transmit Data Request Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 6 C1TXIE: ECAN1 Transmit Data Request Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 5 DMA7IE: DMA Channel 7 Data Transfer Complete Enable Status bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 4 DMA6IE: DMA Channel 6 Data Transfer Complete Enable Status bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 3 Unimplemented: Read as ‘0’

bit 2 U2EIE: UART2 Error Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 1 U1EIE: UART1 Error Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 0 Unimplemented: Read as ‘0’

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

— T1IP<2:0> —OC1IP<2:0>

bit 15 bit 8

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

—IC1IP<2:0>— INT0IP<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-12 T1IP<2:0>: Timer1 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 11 Unimplemented: Read as ‘0’

bit 10-8 OC1IP<2:0>: Output Compare Channel 1 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 7 Unimplemented: Read as ‘0’

bit 6-4 IC1IP<2:0>: Input Capture Channel 1 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 3 Unimplemented: Read as ‘0’

bit 2-0 INT0IP<2:0>: External Interrupt 0 Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

— T2IP<2:0> —OC2IP<2:0>

bit 15 bit 8

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

—IC2IP<2:0>—DMA0IP<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-12 T2IP<2:0>: Timer2 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 11 Unimplemented: Read as ‘0’

bit 10-8 OC2IP<2:0>: Output Compare Channel 2 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 7 Unimplemented: Read as ‘0’

bit 6-4 IC2IP<2:0>: Input Capture Channel 2 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 3 Unimplemented: Read as ‘0’

bit 2-0 DMA0IP<2:0>: DMA Channel 0 Data Transfer Complete Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

— U1RXIP<2:0> — SPI1IP<2:0>

bit 15 bit 8

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

— SPI1EIP<2:0> — T3IP<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-12 U1RXIP<2:0>: UART1 Receiver Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 11 Unimplemented: Read as ‘0’

bit 10-8 SPI1IP<2:0>: SPI1 Event Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 7 Unimplemented: Read as ‘0’

bit 6-4 SPI1EIP<2:0>: SPI1 Error Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 3 Unimplemented: Read as ‘0’

bit 2-0 T3IP<2:0>: Timer3 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 U-0 U-0 R/W-1 R/W-0 R/W-0

— — — — —DMA1IP<2:0>

bit 15 bit 8

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

—AD1IP<2:0>— U1TXIP<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-11 Unimplemented: Read as ‘0’

bit 10-8 DMA1IP<2:0>: DMA Channel 1 Data Transfer Complete Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 7 Unimplemented: Read as ‘0’

bit 6-4 AD1IP<2:0>: ADC1 Conversion Complete Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 3 Unimplemented: Read as ‘0’

bit 2-0 U1TXIP<2:0>: UART1 Transmitter Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0

— CNIP<2:0> — — — —

bit 15 bit 8

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

— MI2C1IP<2:0> — SI2C1IP<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-12 CNIP<2:0>: Change Notification Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 11-7 Unimplemented: Read as ‘0’

bit 6-4 MI2C1IP<2:0>: I2C1 Master Events Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 3 Unimplemented: Read as ‘0’

bit 2-0 SI2C1IP<2:0>: I2C1 Slave Events Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

—IC8IP<2:0>— IC7IP<2:0>

bit 15 bit 8

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

—AD2IP<2:0>— INT1IP<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-12 IC8IP<2:0>: Input Capture Channel 8 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 11 Unimplemented: Read as ‘0’

bit 10-8 IC7IP<2:0>: Input Capture Channel 7 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 7 Unimplemented: Read as ‘0’

bit 6-4 AD2IP<2:0>: ADC2 Conversion Complete Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 3 Unimplemented: Read as ‘0’

bit 2-0 INT1IP<2:0>: External Interrupt 1 Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

— T4IP<2:0> —OC4IP<2:0>

bit 15 bit 8

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

— OC3IP<2:0> —DMA2IP<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-12 T4IP<2:0>: Timer4 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 11 Unimplemented: Read as ‘0’

bit 10-8 OC4IP<2:0>: Output Compare Channel 4 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 7 Unimplemented: Read as ‘0’

bit 6-4 OC3IP<2:0>: Output Compare Channel 3 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 3 Unimplemented: Read as ‘0’

bit 2-0 DMA2IP<2:0>: DMA Channel 2 Data Transfer Complete Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

— U2TXIP<2:0> — U2RXIP<2:0>

bit 15 bit 8

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

— INT2IP<2:0> — T5IP<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-12 U2TXIP<2:0>: UART2 Transmitter Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 11 Unimplemented: Read as ‘0’

bit 10-8 U2RXIP<2:0>: UART2 Receiver Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 7 Unimplemented: Read as ‘0’

bit 6-4 INT2IP<2:0>: External Interrupt 2 Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 3 Unimplemented: Read as ‘0’

bit 2-0 T5IP<2:0>: Timer5 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

— C1IP<2:0> — C1RXIP<2:0>

bit 15 bit 8

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

— SPI2IP<2:0> — SPI2EIP<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-12 C1IP<2:0>: ECAN1 Event Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 11 Unimplemented: Read as ‘0’

bit 10-8 C1RXIP<2:0>: ECAN1 Receive Data Ready Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 7 Unimplemented: Read as ‘0’

bit 6-4 SPI2IP<2:0>: SPI2 Event Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 3 Unimplemented: Read as ‘0’

bit 2-0 SPI2EIP<2:0>: SPI2 Error Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

—IC5IP<2:0>— IC4IP<2:0>

bit 15 bit 8

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

—IC3IP<2:0>—DMA3IP<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-12 IC5IP<2:0>: Input Capture Channel 5 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 11 Unimplemented: Read as ‘0’

bit 10-8 IC4IP<2:0>: Input Capture Channel 4 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 7 Unimplemented: Read as ‘0’

bit 6-4 IC3IP<2:0>: Input Capture Channel 3 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 3 Unimplemented: Read as ‘0’

bit 2-0 DMA3IP<2:0>: DMA Channel 3 Data Transfer Complete Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

— OC7IP<2:0> —OC6IP<2:0>

bit 15 bit 8

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

— OC5IP<2:0> — IC6IP<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-12 OC7IP<2:0>: Output Compare Channel 7 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 11 Unimplemented: Read as ‘0’

bit 10-8 OC6IP<2:0>: Output Compare Channel 6 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 7 Unimplemented: Read as ‘0’

bit 6-4 OC5IP<2:0>: Output Compare Channel 5 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 3 Unimplemented: Read as ‘0’

bit 2-0 IC6IP<2:0>: Input Capture Channel 6 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

— T6IP<2:0> —DMA4IP<2:0>

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 R/W-1 R/W-0 R/W-0

— — — — —OC8IP<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-12 T6IP<2:0>: Timer6 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 11 Unimplemented: Read as ‘0’

bit 10-8 DMA4IP<2:0>: DMA Channel 4 Data Transfer Complete Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 7-3 Unimplemented: Read as ‘0’

bit 2-0 OC8IP<2:0>: Output Compare Channel 8 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

— T8IP<2:0> — MI2C2IP<2:0>

bit 15 bit 8

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

— SI2C2IP<2:0> — T7IP<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-12 T8IP<2:0>: Timer8 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 11 Unimplemented: Read as ‘0’

bit 10-8 MI2C2IP<2:0>: I2C2 Master Events Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 7 Unimplemented: Read as ‘0’

bit 6-4 SI2C2IP<2:0>: I2C2 Slave Events Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 3 Unimplemented: Read as ‘0’

bit 2-0 T7IP<2:0>: Timer7 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

— C2RXIP<2:0> — INT4IP<2:0>

bit 15 bit 8

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

— INT3IP<2:0> — T9IP<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-12 C2RXIP<2:0>: ECAN2 Receive Data Ready Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 11 Unimplemented: Read as ‘0’

bit 10-8 INT4IP<2:0>: External Interrupt 4 Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 7 Unimplemented: Read as ‘0’

bit 6-4 INT3IP<2:0>: External Interrupt 3 Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 3 Unimplemented: Read as ‘0’

bit 2-0 T9IP<2:0>: Timer9 Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0

— DCIEIP<2:0> — — — —

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 R/W-1 R/W-0 R/W-0

— — — — — C2IP<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-12 DCIEIP<2:0>: DCI Error Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 11-3 Unimplemented: Read as ‘0’

bit 2-0 C2IP<2:0>: ECAN2 Event Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

— DMA5IP<2:0> —DCIIP<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-7 Unimplemented: Read as ‘0’

bit 6-4 DMA5IP<2:0>: DMA Channel 5 Data Transfer Complete Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 3 Unimplemented: Read as ‘0’

bit 2-0 DCIIP<2:0>: DCI Event Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 U-0 U-0 R/W-1 R/W-0 R/W-0

— — — — — U2EIP<2:0>

bit 15 bit 8

U-0 R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0

—U1EIP<2:0>— — — —

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-11 Unimplemented: Read as ‘0’

bit 10-8 U2EIP<2:0>: UART2 Error Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 7 Unimplemented: Read as ‘0’

bit 6-4 U1EIP<2:0>: UART1 Error Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 3-0 Unimplemented: Read as ‘0’

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

— C2TXIP<2:0> — C1TXIP<2:0>

bit 15 bit 8

U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0

— DMA7IP<2:0> —DMA6IP<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-12 C2TXIP<2:0>: ECAN2 Transmit Data Request Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 11 Unimplemented: Read as ‘0’

bit 10-8 C1TXIP<2:0>: ECAN1 Transmit Data Request Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 7 Unimplemented: Read as ‘0’

bit 6-4 DMA7IP<2:0>: DMA Channel 7 Data Transfer Complete Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

bit 3 Unimplemented: Read as ‘0’

bit 2-0 DMA6IP<2:0>: DMA Channel 6 Data Transfer Complete Interrupt Priority bits

111 = Interrupt is priority 7 (highest priority interrupt)

•

001 = Interrupt is priority 1

000 = Interrupt source is disabled

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 U-0 R-0 R-0 R-0 R-0

— — — —ILR<3:0>

bit 15 bit 8

U-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

— VECNUM<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 Unimplemented: Read as ‘0’

bit 11-8 ILR<3:0>: New CPU Interrupt Priority Level bits

1111 = CPU Interrupt Priority Level is 15

•

0001 = CPU Interrupt Priority Level is 1

0000 = CPU Interrupt Priority Level is 0

bit 7 Unimplemented: Read as ‘0’

bit 6-0 VECNUM<6:0>: Vector Number of Pending Interrupt bits

0111111 = Interrupt Vector pending is number 135

•

0000001 = Interrupt Vector pending is number 9

0000000 = Interrupt Vector pending is number 8

dsPIC33FJXXXGPX06A/X08A/X10A

7.4 Interrupt Setup Procedures

7.4.1 INITIALIZATION

To configure an interrupt source:

1. Set the NSTDIS bit (INTCON1<15>) if nested

interrupts are not desired.

2. Select the user-assigned priority level for the

interrupt source by writing the control bits in the

appropriate IPCx register. The priority level will

depend on the specific application and type of

interrupt source. If multiple priority levels are not

desired, the IPCx register control bits for all

enabled interrupt sources may be programmed

to the same non-zero value.

3. Clear the interrupt flag status bit associated with

the peripheral in the associated IFSx register.

4. Enable the interrupt source by setting the

interrupt enable control bit associated with the

source in the appropriate IECx register.

7.4.2 INTERRUPT SERVICE ROUTINE

The method that is used to declare an ISR and initialize

the IVT with the correct vector address will depend on

the programming language (i.e., C or assembler) and

the language development toolsuite that is used to

develop the application. In general, the user must clear

the interrupt flag in the appropriate IFSx register for the

source of interrupt that the ISR handles. Otherwise, the

ISR will be re-entered immediately after exiting the

routine. If the ISR is coded in assembly language, it

must be terminated using a RETFIE instruction to

unstack the saved PC value, SRL value and old CPU

priority level.

7.4.3 TRAP SERVICE ROUTINE

A Trap Service Routine (TSR) is coded like an ISR,

except that the appropriate trap status flag in the

INTCON1 register must be cleared to avoid re-entry

into the TSR.

7.4.4 INTERRUPT DISABLE

All user interrupts can be disabled using the following

procedure:

1. Push the current SR value onto the software

stack using the PUSH instruction.

2. Force the CPU to priority level 7 by inclusive

ORing the value OEh with SRL.

To enable user interrupts, the POP instruction may be

used to restore the previous SR value.

Note that only user interrupts with a priority level of 7 or

less can be disabled. Trap sources (level 8-level 15)

cannot be disabled.

The DISI instruction provides a convenient way to

disable interrupts of priority levels 1-6 for a fixed period

of time. Level 7 interrupt sources are not disabled by

the DISI instruction.

Note: At a device Reset, the IPCx registers are

initialized, such that all user interrupt

sources are assigned to priority level 4.

dsPIC33FJXXXGPX06A/X08A/X10A

NOTES:

dsPIC33FJXXXGPX06A/X08A/X10A

8.0 DIRECT MEMORY ACCESS

(DMA)

Direct Memory Access (DMA) is a very efficient

mechanism of copying data between peripheral SFRs

(e.g., UART Receive register, Input Capture 1 buffer),

and buffers or variables stored in RAM, with minimal

CPU intervention. The DMA controller can

automatically copy entire blocks of data without

requiring the user software to read or write the

peripheral Special Function Registers (SFRs) every

time a peripheral interrupt occurs. The DMA controller

uses a dedicated bus for data transfers and therefore,

does not steal cycles from the code execution flow of

the CPU. To exploit the DMA capability, the

corresponding user buffers or variables must be

located in DMA RAM.

The dsPIC33FJXXXGPX06A/X08A/X10A peripherals

that can utilize DMA are listed in Ta b l e 8 - 1 along with

their associated Interrupt Request (IRQ) numbers.

TABLE 8-1: PERIPHERALS WITH DMA

SUPPORT

The DMA controller features eight identical data

transfer channels.

Each channel has its own set of control and status reg-

isters. Each DMA channel can be configured to copy

data either from buffers stored in dual port DMA RAM

to peripheral SFRs, or from peripheral SFRs to buffers

in DMA RAM.

The DMA controller supports the following features:

• Word or byte sized data transfers

• Transfers from peripheral to DMA RAM or DMA

RAM to peripheral

• Indirect Addressing of DMA RAM locations with or

without automatic post-increment

• Peripheral Indirect Addressing – In some

peripherals, the DMA RAM read/write addresses

may be partially derived from the peripheral

• One-Shot Block Transfers – Terminating DMA

transfer after one block transfer

• Continuous Block Transfers – Reloading DMA

RAM buffer start address after every block

transfer is complete

• Ping-Pong Mode – Switching between two DMA

RAM start addresses between successive block

transfers, thereby filling two buffers alternately

• Automatic or manual initiation of block transfers

• Each channel can select from 20 possible

sources of data sources or destinations

For each DMA channel, a DMA interrupt request is

generated when a block transfer is complete.

Alternatively, an interrupt can be generated when half

of the block has been filled.

Note 1: This data sheet summarizes the features

of the dsPIC33FJXXXGPX06A/X08A/

X10A family of devices. However, it is not

intended to be a comprehensive refer-

ence source. To complement the infor-

mation in this data sheet, refer to Section

22. “Direct Memory Access (DMA)”

(DS70182) in the “dsPIC33F/PIC24H

Family Reference Manual”, which is

available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Peripheral IRQ Number

INT0 0

Input Capture 1 1

Input Capture 2 5

Output Compare 1 2

Output Compare 2 6

Timer2 7

Timer3 8

SPI1 10

SPI2 33

UART1 Reception 11

UART1 Transmission 12

UART2 Reception 30

UART2 Transmission 31

ADC1 13

ADC2 21

DCI 60

ECAN1 Reception 34

ECAN1 Transmission 70

ECAN2 Reception 55

ECAN2 Transmission 71

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 8-1: TOP LEVEL SYSTEM ARCHITECTURE USING A DEDICATED TRANSACTION BUS

8.1 DMAC Registers

Each DMAC Channel x (x = 0, 1, 2, 3, 4, 5, 6 or 7)

contains the following registers:

• A 16-bit DMA Channel Control register

(DMAxCON)

• A 16-bit DMA Channel IRQ Select register

(DMAxREQ)

• A 16-bit DMA RAM Primary Start Address Offset

• A 16-bit DMA RAM Secondary Start Address

Offset register (DMAxSTB)

• A 16-bit DMA Peripheral Address register

(DMAxPAD)

• A 10-bit DMA Transfer Count register (DMAxCNT)

An additional pair of status registers, DMACS0 and

DMACS1, are common to all DMAC channels.

CPU

SRAM DMA RAM

CPU Peripheral DS Bus

Peripheral 3

DMA

Peripheral

Non-DMA

SRAM X-Bus

PORT 2PORT 1

Peripheral 1

DMA

Ready

Peripheral 2

DMA

Ready

DMA DS Bus

CPU DMA

CPU DMA CPU DMA

Peripheral Indirect Address

Note: CPU and DMA address buses are not shown for clarity.

DMA

Control

DMA Controller

DMA

Channels

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 U-0

CHEN SIZE DIR HALF NULLW — — —

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 U-0 U-0 R/W-0 R/W-0

——AMODE<1:0>—— MODE<1:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 CHEN: Channel Enable bit

1 = Channel enabled

0 = Channel disabled

bit 14 SIZE: Data Transfer Size bit

1 = Byte

0 = Word

bit 13 DIR: Transfer Direction bit (source/destination bus select)

1 = Read from DMA RAM address, write to peripheral address

0 = Read from peripheral address, write to DMA RAM address

bit 12 HALF: Early Block Transfer Complete Interrupt Select bit

1 = Initiate block transfer complete interrupt when half of the data has been moved

0 = Initiate block transfer complete interrupt when all of the data has been moved

bit 11 NULLW: Null Data Peripheral Write Mode Select bit

1 = Null data write to peripheral in addition to DMA RAM write (DIR bit must also be clear)

0 = Normal operation

bit 10-6 Unimplemented: Read as ‘0’

bit 5-4 AMODE<1:0>: DMA Channel Operating Mode Select bits

11 = Reserved

10 = Peripheral Indirect Addressing mode

01 = Register Indirect without Post-Increment mode

00 = Register Indirect with Post-Increment mode

bit 3-2 Unimplemented: Read as ‘0’

bit 1-0 MODE<1:0>: DMA Channel Operating Mode Select bits

11 = One-Shot, Ping-Pong modes enabled (one block transfer from/to each DMA RAM buffer)

10 = Continuous, Ping-Pong modes enabled

01 = One-Shot, Ping-Pong modes disabled

00 = Continuous, Ping-Pong modes disabled

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

FORCE(1) — — — — — — —

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— IRQSEL6(2) IRQSEL5(2) IRQSEL4(2) IRQSEL3(2) IRQSEL2(2) IRQSEL1(2) IRQSEL0(2)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 FORCE: Force DMA Transfer bit(1)

1 = Force a single DMA transfer (Manual mode)

0 = Automatic DMA transfer initiation by DMA request

bit 14-7 Unimplemented: Read as ‘0’

bit 6-0 IRQSEL<6:0>: DMA Peripheral IRQ Number Select bits(2)

1111111 = DMAIRQ127 selected to be Channel DMAREQ

•

0000000 = DMAIRQ0 selected to be Channel DMAREQ

Note 1: The FORCE bit cannot be cleared by the user. The FORCE bit is cleared by hardware when the forced

DMA transfer is complete.

2: Please see Ta b l e 8 - 1 for a complete listing of IRQ numbers for all interrupt sources.

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

STA<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

STA<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 STA<15:0>: Primary DMA RAM Start Address bits (source or destination)

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

STB<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

STB<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 STB<15:0>: Secondary DMA RAM Start Address bits (source or destination)

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PAD<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PAD<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 PAD<15:0>: Peripheral Address Register bits

Note 1: If the channel is enabled (i.e., active), writes to this register may result in unpredictable behavior of the

DMA channel and should be avoided.

U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0

— — — — — — CNT<9:8>(2)

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

CNT<7:0>(2)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-10 Unimplemented: Read as ‘0’

bit 9-0 CNT<9:0>: DMA Transfer Count Register bits(2)

Note 1: If the channel is enabled (i.e., active), writes to this register may result in unpredictable behavior of the

DMA channel and should be avoided.

2: Number of DMA transfers = CNT<9:0> + 1.

dsPIC33FJXXXGPX06A/X08A/X10A

R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0

PWCOL7 PWCOL6 PWCOL5 PWCOL4 PWCOL3 PWCOL2 PWCOL1 PWCOL0

bit 15 bit 8

R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0

XWCOL7 XWCOL6 XWCOL5 XWCOL4 XWCOL3 XWCOL2 XWCOL1 XWCOL0

bit 7 bit 0

Legend: C = Clear only bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 PWCOL7: Channel 7 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 14 PWCOL6: Channel 6 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 13 PWCOL5: Channel 5 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 12 PWCOL4: Channel 4 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 11 PWCOL3: Channel 3 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 10 PWCOL2: Channel 2 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 9 PWCOL1: Channel 1 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 8 PWCOL0: Channel 0 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 7 XWCOL7: Channel 7 DMA RAM Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 6 XWCOL6: Channel 6 DMA RAM Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 5 XWCOL5: Channel 5 DMA RAM Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 4 XWCOL4: Channel 4 DMA RAM Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

dsPIC33FJXXXGPX06A/X08A/X10A

bit 3 XWCOL3: Channel 3 DMA RAM Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 2 XWCOL2: Channel 2 DMA RAM Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 1 XWCOL1: Channel 1 DMA RAM Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 0 XWCOL0: Channel 0 DMA RAM Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 U-0 R-1 R-1 R-1 R-1

— — — — LSTCH<3:0>

bit 15 bit 8

R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

PPST7 PPST6 PPST5 PPST4 PPST3 PPST2 PPST1 PPST0

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 Unimplemented: Read as ‘0’

bit 11-8 LSTCH<3:0>: Last DMA Channel Active bits

1111 = No DMA transfer has occurred since system Reset

1110-1000 = Reserved

0111 = Last data transfer was by DMA Channel 7

0110 = Last data transfer was by DMA Channel 6

0101 = Last data transfer was by DMA Channel 5

0100 = Last data transfer was by DMA Channel 4

0011 = Last data transfer was by DMA Channel 3

0010 = Last data transfer was by DMA Channel 2

0001 = Last data transfer was by DMA Channel 1

0000 = Last data transfer was by DMA Channel 0

bit 7 PPST7: Channel 7 Ping-Pong Mode Status Flag bit

1 = DMA7STB register selected

0 = DMA7STA register selected

bit 6 PPST6: Channel 6 Ping-Pong Mode Status Flag bit

1 = DMA6STB register selected

0 = DMA6STA register selected

bit 5 PPST5: Channel 5 Ping-Pong Mode Status Flag bit

1 = DMA5STB register selected

0 = DMA5STA register selected

bit 4 PPST4: Channel 4 Ping-Pong Mode Status Flag bit

1 = DMA4STB register selected

0 = DMA4STA register selected

bit 3 PPST3: Channel 3 Ping-Pong Mode Status Flag bit

1 = DMA3STB register selected

0 = DMA3STA register selected

bit 2 PPST2: Channel 2 Ping-Pong Mode Status Flag bit

1 = DMA2STB register selected

0 = DMA2STA register selected

bit 1 PPST1: Channel 1 Ping-Pong Mode Status Flag bit

1 = DMA1STB register selected

0 = DMA1STA register selected

bit 0 PPST0: Channel 0 Ping-Pong Mode Status Flag bit

1 = DMA0STB register selected

0 = DMA0STA register selected

dsPIC33FJXXXGPX06A/X08A/X10A

R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

DSADR<15:8>

bit 15 bit 8

R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

DSADR<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 DSADR<15:0>: Most Recent DMA RAM Address Accessed by DMA Controller bits

dsPIC33FJXXXGPX06A/X08A/X10A

9.0 OSCILLATOR

CONFIGURATION

The dsPIC33FJXXXGPX06A/X08A/X10A oscillator

system provides:

• Various external and internal oscillator options as

clock sources

• An on-chip PLL to scale the internal operating

frequency to the required system clock frequency

• The internal FRC oscillator can also be used with

the PLL, thereby allowing full-speed operation

without any external clock generation hardware

• Clock switching between various clock sources

• Programmable clock postscaler for system power

savings

• A Fail-Safe Clock Monitor (FSCM) that detects

clock failure and takes fail-safe measures

• An Oscillator Control register (OSCCON)

• Nonvolatile Configuration bits for main oscillator

selection

A simplified diagram of the oscillator system is shown

in Figure 9-1.

FIGURE 9-1: dsPIC33FJXXXGPX06A/X08A/X10A OSCILLATOR SYSTEM DIAGRAM

Note 1: This data sheet summarizes the

features of the dsPIC33FJXXXGPX06A/

X08A/X10A family of devices. However,

it is not intended to be a

comprehensive reference source. To

complement the information in this data

sheet, refer to Section 7. “Oscillator”

(DS70186) in the “dsPIC33F/PIC24H

Family Reference Manual”, which is

available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Secondary Oscillator

LPOSCEN

SOSCO

SOSCI

Timer 1

XTPLL, HSPLL,

XT, HS, EC

FRCDIV<2:0>

WDT, PWRT,

FSCM

FRCDIVN

SOSC

FRCDIV16

ECPLL, FRCPLL

NOSC<2:0> FNOSC<2:0>

Reset

FRC

Oscillator

LPRC

Oscillator

DOZE<2:0>

S1/S3

FRC

LPRC

÷16

Clock Switch

Clock Fail

÷2

TUN<5:0>

PLL(1) FCY

FOSC

FRCDIV

DOZE

Note 1: See Figure 9-2 for PLL details.

2: If the Oscillator is used with XT or HS modes, an extended parallel resistor with the value of 1 MΩ must be connected.

3: The term, FP refers to the clock source for all the peripherals, while FCY refers to the clock source for the CPU.

Throughout this document FP and FCY are used interchangeably, except in the case of Doze mode. FP and FCY will be

different when Doze mode is used in any ratio other than 1:1, which is the default.

OSC2

OSC1 Primary Oscillator

R(2)

POSCMD<1:0>

FP(3)

dsPIC33FJXXXGPX06A/X08A/X10A

9.1 CPU Clocking System

There are seven system clock options provided by the

dsPIC33FJXXXGPX06A/X08A/X10A:

• FRC Oscillator

• FRC Oscillator with PLL

• Primary (XT, HS or EC) Oscillator

• Primary Oscillator with PLL

• Secondary (LP) Oscillator

• LPRC Oscillator

• FRC Oscillator with postscaler

9.1.1 SYSTEM CLOCK SOURCES

The FRC (Fast RC) internal oscillator runs at a nominal

frequency of 7.37 MHz. The user software can tune the

FRC frequency. User software can optionally specify a

factor (ranging from 1:2 to 1:256) by which the FRC

clock frequency is divided. This factor is selected using

the FRCDIV<2:0> (CLKDIV<10:8>) bits.

The primary oscillator can use one of the following as

its clock source:

• XT (Crystal): Crystals and ceramic resonators in

the range of 3 MHz to 10 MHz. The crystal is con-

nected to the OSC1 and OSC2 pins.

• HS (High-Speed Crystal): Crystals in the range of

10 MHz to 40 MHz. The crystal is connected to

the OSC1 and OSC2 pins.

• EC (External Clock): External clock signal is

directly applied to the OSC1 pin.

The secondary (LP) oscillator is designed for low power

and uses a 32.768 kHz crystal or ceramic resonator.

The LP oscillator uses the SOSCI and SOSCO pins.

The LPRC (Low-Power RC) internal oscillator runs at a

nominal frequency of 32.768 kHz. It is also used as a

reference clock by the Watchdog Timer (WDT) and

Fail-Safe Clock Monitor (FSCM).

The clock signals generated by the FRC and primary

oscillators can be optionally applied to an on-chip

Phase Locked Loop (PLL) to provide a wide range of

output frequencies for device operation. PLL

configuration is described in Section 9.1.3 “PLL

Configuration”.

The FRC frequency depends on the FRC accuracy

(see Table 25-19) and the value of the FRC Oscillator

Tuning register (see Register 9-4).

9.1.2 SYSTEM CLOCK SELECTION

The oscillator source that is used at a device Power-on

Reset event is selected using Configuration bit settings.

The oscillator Configuration bit settings are located in the

Configuration registers in the program memory. (Refer to

Section 22.1 “Configuration Bits” for further details.)

The Initial Oscillator Selection Configuration bits,

FNOSC<2:0> (FOSCSEL<2:0>), and the Primary

Oscillator Mode Select Configuration bits,

POSCMD<1:0> (FOSC<1:0>), select the oscillator

source that is used at a Power-on Reset. The FRC

primary oscillator is the default (unprogrammed)

selection.

The Configuration bits allow users to choose between

twelve different clock modes, shown in Table 9-1.

The output of the oscillator (or the output of the PLL if

a PLL mode has been selected) FOSC is divided by 2 to

generate the device instruction clock (FCY) and the

peripheral clock time base (FP). FCY defines the

operating speed of the device, and speeds up to 40

MHz are supported by the dsPIC33FJXXXGPX06A/

X08A/X10A architecture.

Instruction execution speed or device operating

frequency, FCY, is given by:

EQUATION 9-1: DEVICE OPERATING

FREQUENCY

9.1.3 PLL CONFIGURATION

The primary oscillator and internal FRC oscillator can

optionally use an on-chip PLL to obtain higher speeds

of operation. The PLL provides a significant amount of

flexibility in selecting the device operating speed. A

block diagram of the PLL is shown in Figure 9-2.

The output of the primary oscillator or FRC, denoted as

‘FIN’, is divided down by a prescale factor (N1) of 2, 3,

... or 33 before being provided to the PLL’s Voltage

Controlled Oscillator (VCO). The input to the VCO must

be selected to be in the range of 0.8 MHz to 8 MHz.

Since the minimum prescale factor is 2, this implies that

FIN must be chosen to be in the range of 1.6 MHz to 16

MHz. The prescale factor ‘N1’ is selected using the

PLLPRE<4:0> bits (CLKDIV<4:0>).

The PLL Feedback Divisor, selected using the

PLLDIV<8:0> bits (PLLFBD<8:0>), provides a factor ‘M’,

by which the input to the VCO is multiplied. This factor

must be selected such that the resulting VCO output

frequency is in the range of 100 MHz to 200 MHz.

The VCO output is further divided by a postscale factor

‘N2’. This factor is selected using the PLLPOST<1:0>

bits (CLKDIV<7:6>). ‘N2’ can be either 2, 4 or 8, and

must be selected such that the PLL output frequency

(FOSC) is in the range of 12.5 MHz to 80 MHz, which

generates device operating speeds of 6.25-40 MIPS.

For a primary oscillator or FRC oscillator, output ‘FIN’,

the PLL output ‘FOSC’ is given by:

EQUATION 9-2: FOSC CALCULATION

FCY FOSC

-------------=

FOSC FIN M

N1N2⋅

----------------------

⎝⎠

⎛⎞

⋅=

dsPIC33FJXXXGPX06A/X08A/X10A

For example, suppose a 10 MHz crystal is being used,

with “XT with PLL” being the selected oscillator mode.

If PLLPRE<4:0> = 0, then N1 = 2. This yields a VCO

input of 10/2 = 5 MHz, which is within the acceptable

range of 0.8-8 MHz. If PLLDIV<8:0> = 0x1E, then

M = 32. This yields a VCO output of 5 x 32 = 160 MHz,

which is within the 100-200 MHz range needed.

If PLLPOST<1:0> = 0, then N2 = 2. This provides a

Fosc of 160/2 = 80 MHz. The resultant device operating

speed is 80/2 = 40 MIPS.

EQUATION 9-3: XT WITH PLL MODE

EXAMPLE

FIGURE 9-2: dsPIC33FJXXXGPX06A/X08A/X10A PLL BLOCK DIAGRAM

TABLE 9-1: CONFIGURATION BIT VALUES FOR CLOCK SELECTION

FCY FOSC

------------- 1

---10000000 32⋅

22⋅

-------------------------------------

⎝⎠

⎛⎞

40 MIPS== =

Oscillator Mode Oscillator Source POSCMD<1:0> FNOSC<2:0> See Note

Fast RC Oscillator with Divide-by-N

(FRCDIVN)

Internal xx 111 1, 2

Fast RC Oscillator with Divide-by-16

(FRCDIV16)

Internal xx 110 1

Low-Power RC Oscillator (LPRC) Internal xx 101 1

Secondary (Timer1) Oscillator (SOSC) Secondary xx 100 1

Primary Oscillator (HS) with PLL

(HSPLL)

Primary 10 011 —

Primary Oscillator (XT) with PLL

(XTPLL)

Primary 01 011 —

Primary Oscillator (EC) with PLL

(ECPLL)

Primary 00 011 1

Primary Oscillator (HS) Primary 10 010 —

Primary Oscillator (XT) Primary 01 010 —

Primary Oscillator (EC) Primary 00 010 1

Fast RC Oscillator with PLL (FRCPLL) Internal xx 001 1

Fast RC Oscillator (FRC) Internal xx 000 1

Note 1: OSC2 pin function is determined by the OSCIOFNC Configuration bit.

2: This is the default oscillator mode for an unprogrammed (erased) device.

0.8-8.0 MHz

Here(1) 100-200 MHz

Here(1)

Divide by

2, 4, 8

Divide by

2-513

Divide by

2-33

Source (Crystal, External Clock PLLPRE XVCO

PLLDIV

PLLPOST

or Internal RC)

12.5-80 MHz

Here(1)

FOSC

Note 1: This frequency range must be satisfied at all times.

FVCO

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 R-0 R-0 R-0 U-0 R/W-y R/W-y R/W-y

— COSC<2:0> — NOSC<2:0>(2)

bit 15 bit 8

R/W-0 U-0 R-0 U-0 R/C-0 U-0 R/W-0 R/W-0

CLKLOCK —LOCK—CF — LPOSCEN OSWEN

bit 7 bit 0

Legend: y = Value set from Configuration bits on POR C = Clear only bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-12 COSC<2:0>: Current Oscillator Selection bits (read-only)

111 = Fast RC oscillator (FRC) with Divide-by-n

110 = Fast RC oscillator (FRC) with Divide-by-16

101 = Low-Power RC oscillator (LPRC)

100 = Secondary oscillator (SOSC)

011 = Primary oscillator (XT, HS, EC) with PLL

010 = Primary oscillator (XT, HS, EC)

001 = Fast RC oscillator (FRC) with PLL

000 = Fast RC oscillator (FRC)

bit 11 Unimplemented: Read as ‘0’

bit 10-8 NOSC<2:0>: New Oscillator Selection bits(2)

111 = Fast RC oscillator (FRC) with Divide-by-n

110 = Fast RC oscillator (FRC) with Divide-by-16

101 = Low-Power RC oscillator (LPRC)

100 = Secondary oscillator (SOSC)

011 = Primary oscillator (XT, HS, EC) with PLL

010 = Primary oscillator (XT, HS, EC)

001 = Fast RC oscillator (FRC) with PLL

000 = Fast RC oscillator (FRC)

bit 7 CLKLOCK: Clock Lock Enable bit

1 = If (FCKSM0 = 1), then clock and PLL configurations are locked

If (FCKSM0 = 0), then clock and PLL configurations may be modified

0 = Clock and PLL selections are not locked, configurations may be modified

bit 6 Unimplemented: Read as ‘0’

bit 5 LOCK: PLL Lock Status bit (read-only)

1 = Indicates that PLL is in lock, or PLL start-up timer is satisfied

0 = Indicates that PLL is out of lock, start-up timer is in progress or PLL is disabled

bit 4 Unimplemented: Read as ‘0’

bit 3 CF: Clock Fail Detect bit (read/clear by application)

1 = FSCM has detected clock failure

0 = FSCM has not detected clock failure

bit 2 Unimplemented: Read as ‘0’

Note 1: Writes to this register require an unlock sequence. Refer to Section 7. “Oscillator” (DS70186) in the

“dsPIC33F/PIC24H Family Reference Manual” for details.

2: Direct clock switches between any primary oscillator mode with PLL and FRCPLL mode are not permitted.

This applies to clock switches in either direction. In these instances, the application must switch to FRC

mode as a transition clock source between the two PLL modes.

3: This is register is reset only on a Power-on Reset (POR).

dsPIC33FJXXXGPX06A/X08A/X10A

bit 1 LPOSCEN: Secondary (LP) Oscillator Enable bit

1 = Enable secondary oscillator

0 = Disable secondary oscillator

bit 0 OSWEN: Oscillator Switch Enable bit

1 = Request oscillator switch to selection specified by NOSC<2:0> bits

0 = Oscillator switch is complete

Note 1: Writes to this register require an unlock sequence. Refer to Section 7. “Oscillator” (DS70186) in the

“dsPIC33F/PIC24H Family Reference Manual” for details.

2: Direct clock switches between any primary oscillator mode with PLL and FRCPLL mode are not permitted.

This applies to clock switches in either direction. In these instances, the application must switch to FRC

mode as a transition clock source between the two PLL modes.

3: This is register is reset only on a Power-on Reset (POR).

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 R/W-1 R/W-1 R/W-0 R/W-0 R/W-0 R/W-0

ROI DOZE<2:0> DOZEN(1) FRCDIV<2:0>

bit 15 bit 8

R/W-0 R/W-1 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PLLPOST<1:0> — PLLPRE<4:0>

bit 7 bit 0

Legend: y = Value set from Configuration bits on POR

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 ROI: Recover on Interrupt bit

1 = Interrupts will clear the DOZEN bit and the processor clock/peripheral clock ratio is set to 1:1

0 = Interrupts have no effect on the DOZEN bit

bit 14-12 DOZE<2:0>: Processor Clock Reduction Select bits

111 = FCY/128

110 = FCY/64

101 = FCY/32

100 = FCY/16

011 = FCY/8 (default)

010 = FCY/4

001 = FCY/2

000 = FCY/1

bit 11 DOZEN: DOZE Mode Enable bit(1)

1 = DOZE<2:0> field specifies the ratio between the peripheral clocks and the processor clocks

0 = Processor clock/peripheral clock ratio forced to 1:1

bit 10-8 FRCDIV<2:0>: Internal Fast RC Oscillator Postscaler bits

111 = FRC divide by 256

110 = FRC divide by 64

101 = FRC divide by 32

100 = FRC divide by 16

011 = FRC divide by 8

010 = FRC divide by 4

001 = FRC divide by 2

000 = FRC divide by 1 (default)

bit 7-6 PLLPOST<1:0>: PLL VCO Output Divider Select bits (also denoted as ‘N2’, PLL postscaler)

11 = Output/8

10 = Reserved

01 = Output/4 (default)

00 = Output/2

bit 5 Unimplemented: Read as ‘0’

bit 4-0 PLLPRE<4:0>: PLL Phase Detector Input Divider bits (also denoted as ‘N1’, PLL prescaler)

11111 = Input/33

•

00001 = Input/3

00000 = Input/2 (default)

Note 1: This bit is cleared when the ROI bit is set and an interrupt occurs.

2: This is register is reset only on a Power-on Reset (POR).

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0(1)

— — — — — — —PLLDIV<8>

bit 15 bit 8

R/W-0 R/W-0 R/W-1 R/W-1 R/W-0 R/W-0 R/W-0 R/W-0

PLLDIV<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-9 Unimplemented: Read as ‘0’

bit 8-0 PLLDIV<8:0>: PLL Feedback Divisor bits (also denoted as ‘M’, PLL multiplier)

111111111 = 513

•

000110000 = 50 (default)

•

000000010 = 4

000000001 = 3

000000000 = 2

Note 1: This is register is reset only on a Power-on Reset (POR).

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— TUN<5:0>(1)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-6 Unimplemented: Read as ‘0’

bit 5-0 TUN<5:0>: FRC Oscillator Tuning bits(1)

111111 = Center frequency - 0.375% (7.345 MHz)

•

100001 = Center frequency - 11.625% (6.52 MHz)

100000 = Center frequency - 12% (6.49 MHz)

011111 = Center frequency + 11.625% (8.23 MHz)

011110 = Center frequency + 11.25% (8.20 MHz)

•

000001 = Center frequency + 0.375% (7.40 MHz)

000000 = Center frequency (7.37 MHz nominal)

Note 1: OSCTUN functionality has been provided to help customers compensate for temperature effects on the

FRC frequency over a wide range of temperatures. The tuning step size is an approximation and is neither

characterized nor tested.

2: This is register is reset only on a Power-on Reset (POR).

dsPIC33FJXXXGPX06A/X08A/X10A

9.2 Clock Switching Operation

Applications are free to switch between any of the four

clock sources (Primary, LP, FRC and LPRC) under

software control at any time. To limit the possible side

effects that could result from this flexibility,

dsPIC33FJXXXGPX06A/X08A/X10A devices have a

safeguard lock built into the switch process.

9.2.1 ENABLING CLOCK SWITCHING

To enable clock switching, the FCKSM1 Configuration

bit in the Configuration register must be programmed to

‘0’. (Refer to Section 22.1 “Configuration Bits” for

further details.) If the FCKSM1 Configuration bit is

unprogrammed (‘1’), the clock switching function and

Fail-Safe Clock Monitor function are disabled. This is

the default setting.

The NOSC control bits (OSCCON<10:8>) do not

control the clock selection when clock switching is

disabled. However, the COSC bits (OSCCON<14:12>)

reflect the clock source selected by the FNOSC

Configuration bits.

The OSWEN control bit (OSCCON<0>) has no effect

when clock switching is disabled. It is held at ‘0’ at all

times.

9.2.2 OSCILLATOR SWITCHING SEQUENCE

At a minimum, performing a clock switch requires this

basic sequence:

1. If desired, read the COSC bits

(OSCCON<14:12>) to determine the current

oscillator source.

2. Perform the unlock sequence to allow a write to

the OSCCON register high byte.

3. Write the appropriate value to the NOSC control

bits (OSCCON<10:8>) for the new oscillator

source.

4. Perform the unlock sequence to allow a write to

the OSCCON register low byte.

5. Set the OSWEN bit to initiate the oscillator

switch.

Once the basic sequence is completed, the system

clock hardware responds automatically as follows:

1. The clock switching hardware compares the

COSC status bits with the new value of the

NOSC control bits. If they are the same, then the

clock switch is a redundant operation. In this

case, the OSWEN bit is cleared automatically

and the clock switch is aborted.

2. If a valid clock switch has been initiated, the sta-

tus bits, LOCK (OSCCON<5>) and CF

(OSCCON<3>) are cleared.

3. The new oscillator is turned on by the hardware

if it is not currently running. If a crystal oscillator

must be turned on, the hardware waits until the

Oscillator Start-up Timer (OST) expires. If the

new source is using the PLL, the hardware waits

until a PLL lock is detected (LOCK = 1).

4. The hardware waits for 10 clock cycles from the

new clock source and then performs the clock

switch.

5. The hardware clears the OSWEN bit to indicate a

successful clock transition. In addition, the NOSC

bit values are transferred to the COSC status bits.

6. The old clock source is turned off at this time,

with the exception of LPRC (if WDT or FSCM

are enabled) or LP (if LPOSCEN remains set).

9.3 Fail-Safe Clock Monitor (FSCM)

The Fail-Safe Clock Monitor (FSCM) allows the device

to continue to operate even in the event of an oscillator

failure. The FSCM function is enabled by programming.

If the FSCM function is enabled, the LPRC internal

oscillator runs at all times (except during Sleep mode)

and is not subject to control by the Watchdog Timer.

In the event of an oscillator failure, the FSCM

generates a clock failure trap event and switches the

system clock over to the FRC oscillator. Then the

application program can either attempt to restart the

oscillator or execute a controlled shutdown. The trap

can be treated as a warm Reset by simply loading the

Reset address into the oscillator fail trap vector.

If the PLL multiplier is used to scale the system clock,

the internal FRC is also multiplied by the same factor

on clock failure. Essentially, the device switches to

FRC with PLL on a clock failure.

Note: Primary Oscillator mode has three different

submodes (XT, HS and EC) which are

determined by the POSCMD<1:0>

Configuration bits. While an application

can switch to and from Primary Oscillator

mode in software, it cannot switch

between the different primary submodes

without reprogramming the device.

Note 1: The processor continues to execute code

throughout the clock switching sequence.

Timing sensitive code should not be

executed during this time.

2: Direct clock switches between any pri-

mary oscillator mode with PLL and FRC-

PLL mode are not permitted. This applies

to clock switches in either direction. In

these instances, the application must

switch to FRC mode as a transition clock

source between the two PLL modes.

3: Refer to Section 7. “Oscillator”

(DS70186) in the “dsPIC33F/PIC24H

Family Reference Manual” for details.

dsPIC33FJXXXGPX06A/X08A/X10A

NOTES:

dsPIC33FJXXXGPX06A/X08A/X10A

10.0 POWER-SAVING FEATURES

The dsPIC33FJXXXGPX06A/X08A/X10A devices pro-

vide the ability to manage power consumption by selec-

tively managing clocking to the CPU and the

peripherals. In general, a lower clock frequency and a

reduction in the number of circuits being clocked con-

stitutes lower consumed power.

dsPIC33FJXXXGPX06A/X08A/X10A devices can

manage power consumption in four different ways:

• Clock frequency

• Instruction-based Sleep and Idle modes

• Software-controlled Doze mode

• Selective peripheral control in software

Combinations of these methods can be used to

selectively tailor an application’s power consumption

while still maintaining critical application features, such

as timing-sensitive communications.

10.1 Clock Frequency and Clock

Switching

dsPIC33FJXXXGPX06A/X08A/X10A devices allow a

wide range of clock frequencies to be selected under

application control. If the system clock configuration is

not locked, users can choose low-power or

high-precision oscillators by simply changing the

NOSC bits (OSCCON<10:8>). The process of

changing a system clock during operation, as well as

limitations to the process, are discussed in more detail

in Section 9.0 “Oscillator Configuration”.

10.2 Instruction-Based Power-Saving

Modes

dsPIC33FJXXXGPX06A/X08A/X10A devices have two

special power-saving modes that are entered through

the execution of a special PWRSAV instruction. Sleep

mode stops clock operation and halts all code

execution. Idle mode halts the CPU and code

execution, but allows peripheral modules to continue

operation. The assembly syntax of the PWRSAV

instruction is shown in Example 10-1.

Sleep and Idle modes can be exited as a result of an

enabled interrupt, WDT time-out or a device Reset. When

the device exits these modes, it is said to “wake-up”.

10.2.1 SLEEP MODE

Sleep mode has these features:

• The system clock source is shut down. If an

on-chip oscillator is used, it is turned off.

• The device current consumption is reduced to a

minimum, provided that no I/O pin is sourcing

current

• The Fail-Safe Clock Monitor does not operate

during Sleep mode since the system clock source

is disabled

• The LPRC clock continues to run in Sleep mode if

the WDT is enabled

• The WDT, if enabled, is automatically cleared

prior to entering Sleep mode

• Some device features or peripherals may continue

to operate in Sleep mode. This includes items such

as the input change notification on the I/O ports, or

peripherals that use an external clock input. Any

peripheral that requires the system clock source for

its operation is disabled in Sleep mode.

The device will wake-up from Sleep mode on any of

these events:

• Any interrupt source that is individually enabled

• Any form of device Reset

• A WDT time-out

On wake-up from Sleep, the processor restarts with the

same clock source that was active when Sleep mode

was entered.

EXAMPLE 10-1: PWRSAV INSTRUCTION SYNTAX

Note 1: This data sheet summarizes the features

of the dsPIC33FJXXXGPX06A/X08A/

X10A family of devices. However, it is not

intended to be a comprehensive

reference source. To complement the

information in this data sheet, refer to

Section 9. “Watchdog Timer and

Power-Saving Modes” (DS70196) in

the “dsPIC33F/PIC24H Family

Reference Manual”, which is available

from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Note: SLEEP_MODE and IDLE_MODE are

constants defined in the assembler

include file for the selected device.

PWRSAV #SLEEP_MODE ; Put the device into SLEEP mode

PWRSAV #IDLE_MODE ; Put the device into IDLE mode

dsPIC33FJXXXGPX06A/X08A/X10A

10.2.2 IDLE MODE

Idle mode has these features:

• The CPU stops executing instructions

• The WDT is automatically cleared

• The system clock source remains active. By

default, all peripheral modules continue to operate

normally from the system clock source, but can

also be selectively disabled (see Section 10.4

“Peripheral Module Disable”).

• If the WDT or FSCM is enabled, the LPRC also

remains active

The device will wake from Idle mode on any of these

events:

• Any interrupt that is individually enabled

• Any device Reset

• A WDT time-out

On wake-up from Idle, the clock is reapplied to the CPU

and instruction execution will begin (2-4 clock cycles

later), starting with the instruction following the PWRSAV

instruction, or the first instruction in the ISR.

10.2.3 INTERRUPTS COINCIDENT WITH

POWER SAVE INSTRUCTIONS

Any interrupt that coincides with the execution of a

PWRSAV instruction is held off until entry into Sleep or

Idle mode has completed. The device then wakes up

from Sleep or Idle mode.

10.3 Doze Mode

Generally, changing clock speed and invoking one of the

power-saving modes are the preferred strategies for

reducing power consumption. There may be

circumstances, however, where this is not practical. For

example, it may be necessary for an application to

maintain uninterrupted synchronous communication,

even while it is doing nothing else. Reducing system

clock speed may introduce communication errors, while

using a power-saving mode may stop communications

completely.

Doze mode is a simple and effective alternative method

to reduce power consumption while the device is still

executing code. In this mode, the system clock

continues to operate from the same source and at the

same speed. Peripheral modules continue to be

clocked at the same speed, while the CPU clock speed

is reduced. Synchronization between the two clock

domains is maintained, allowing the peripherals to

access the SFRs while the CPU executes code at a

slower rate.

Doze mode is enabled by setting the DOZEN bit (CLK-

DIV<11>). The ratio between peripheral and core clock

speed is determined by the DOZE<2:0> bits (CLK-

DIV<14:12>). There are eight possible configurations,

from 1:1 to 1:128, with 1:1 being the default setting.

It is also possible to use Doze mode to selectively

reduce power consumption in event-driven

applications. This allows clock-sensitive functions,

such as synchronous communications, to continue

without interruption while the CPU idles, waiting for

something to invoke an interrupt routine. Enabling the

automatic return to full-speed CPU operation on

interrupts is enabled by setting the ROI bit (CLK-

DIV<15>). By default, interrupt events have no effect

on Doze mode operation.

For example, suppose the device is operating at

20 MIPS and the CAN module has been configured for

500 kbps based on this device operating speed. If the

device is now placed in Doze mode with a clock

frequency ratio of 1:4, the CAN module continues to

communicate at the required bit rate of 500 kbps, but

the CPU now starts executing instructions at a

frequency of 5 MIPS.

10.4 Peripheral Module Disable

The Peripheral Module Disable (PMD) registers

provide a method to disable a peripheral module by

stopping all clock sources supplied to that module.

When a peripheral is disabled via the appropriate PMD

control bit, the peripheral is in a minimum power

consumption state. The control and status registers

associated with the peripheral are also disabled, so

writes to those registers will have no effect and read

values will be invalid.

A peripheral module is only enabled if both the

associated bit in the PMD register is cleared and the

peripheral is supported by the specific dsPIC® DSC

variant. If the peripheral is present in the device, it is

enabled in the PMD register by default.

Note: If a PMD bit is set, the corresponding

module is disabled after a delay of

1 instruction cycle. Similarly, if a PMD bit

is cleared, the corresponding module is

enabled after a delay of 1 instruction cycle

(assuming the module control registers

are already configured to enable module

operation).

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 R/W-0

T5MD T4MD T3MD T2MD T1MD —— DCIMD

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

I2C1MD U2MD U1MD SPI2MD SPI1MD C2MD C1MD AD1MD(1)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 T5MD: Timer5 Module Disable bit

1 = Timer5 module is disabled

0 = Timer5 module is enabled

bit 14 T4MD: Timer4 Module Disable bit

1 = Timer4 module is disabled

0 = Timer4 module is enabled

bit 13 T3MD: Timer3 Module Disable bit

1 = Timer3 module is disabled

0 = Timer3 module is enabled

bit 12 T2MD: Timer2 Module Disable bit

1 = Timer2 module is disabled

0 = Timer2 module is enabled

bit 11 T1MD: Timer1 Module Disable bit

1 = Timer1 module is disabled

0 = Timer1 module is enabled

bit 10-9 Unimplemented: Read as ‘0’

bit 8 DCIMD: DCI Module Disable bit

1 = DCI module is disabled

0 = DCI module is enabled

bit 7 I2C1MD: I2C1 Module Disable bit

1 = I2C1 module is disabled

0 = I2C1 module is enabled

bit 6 U2MD: UART2 Module Disable bit

1 = UART2 module is disabled

0 = UART2 module is enabled

bit 5 U1MD: UART1 Module Disable bit

1 = UART1 module is disabled

0 = UART1 module is enabled

bit 4 SPI2MD: SPI2 Module Disable bit

1 = SPI2 module is disabled

0 = SPI2 module is enabled

bit 3 SPI1MD: SPI1 Module Disable bit

1 = SPI1 module is disabled

0 = SPI1 module is enabled

Note 1: PCFGx bits have no effect if ADC module is disabled by setting this bit. In this case all port pins

multiplexed with ANx will be in Digital mode.

dsPIC33FJXXXGPX06A/X08A/X10A

bit 2 C2MD: ECAN2 Module Disable bit

1 = ECAN2 module is disabled

0 = ECAN2 module is enabled

bit 1 C1MD: ECAN2 Module Disable bit

1 = ECAN1 module is disabled

0 = ECAN1 module is enabled

bit 0 AD1MD: ADC1 Module Disable bit(1)

1 = ADC1 module is disabled

0 = ADC1 module is enabled

Note 1: PCFGx bits have no effect if ADC module is disabled by setting this bit. In this case all port pins

multiplexed with ANx will be in Digital mode.

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

IC8MD IC7MD IC6MD IC5MD IC4MD IC3MD IC2MD IC1MD

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

OC8MD OC7MD OC6MD OC5MD OC4MD OC3MD OC2MD OC1MD

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 IC8MD: Input Capture 8 Module Disable bit

1 = Input Capture 8 module is disabled

0 = Input Capture 8 module is enabled

bit 14 IC7MD: Input Capture 7 Module Disable bit

1 = Input Capture 7 module is disabled

0 = Input Capture 7 module is enabled

bit 13 IC6MD: Input Capture 6 Module Disable bit

1 = Input Capture 6 module is disabled

0 = Input Capture 6 module is enabled

bit 12 IC5MD: Input Capture 5 Module Disable bit

1 = Input Capture 5 module is disabled

0 = Input Capture 5 module is enabled

bit 11 IC4MD: Input Capture 4 Module Disable bit

1 = Input Capture 4 module is disabled

0 = Input Capture 4 module is enabled

bit 10 IC3MD: Input Capture 3 Module Disable bit

1 = Input Capture 3 module is disabled

0 = Input Capture 3 module is enabled

bit 9 IC2MD: Input Capture 2 Module Disable bit

1 = Input Capture 2 module is disabled

0 = Input Capture 2 module is enabled

bit 8 IC1MD: Input Capture 1 Module Disable bit

1 = Input Capture 1 module is disabled

0 = Input Capture 1 module is enabled

bit 7 OC8MD: Output Compare 8 Module Disable bit

1 = Output Compare 8 module is disabled

0 = Output Compare 8 module is enabled

bit 6 OC7MD: Output Compare 4 Module Disable bit

1 = Output Compare 7 module is disabled

0 = Output Compare 7 module is enabled

bit 5 OC6MD: Output Compare 6 Module Disable bit

1 = Output Compare 6 module is disabled

0 = Output Compare 6 module is enabled

bit 4 OC5MD: Output Compare 5 Module Disable bit

1 = Output Compare 5 module is disabled

0 = Output Compare 5 module is enabled

dsPIC33FJXXXGPX06A/X08A/X10A

bit 3 OC4MD: Output Compare 4 Module Disable bit

1 = Output Compare 4 module is disabled

0 = Output Compare 4 module is enabled

bit 2 OC3MD: Output Compare 3 Module Disable bit

1 = Output Compare 3 module is disabled

0 = Output Compare 3 module is enabled

bit 1 OC2MD: Output Compare 2 Module Disable bit

1 = Output Compare 2 module is disabled

0 = Output Compare 2 module is enabled

bit 0 OC1MD: Output Compare 1 Module Disable bit

1 = Output Compare 1 module is disabled

0 = Output Compare 1 module is enabled

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 U-0

T9MD T8MD T7MD T6MD ————

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0

—————— I2C2MD AD2MD(1)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 T9MD: Timer9 Module Disable bit

1 = Timer9 module is disabled

0 = Timer9 module is enabled

bit 14 T8MD: Timer8 Module Disable bit

1 = Timer8 module is disabled

0 = Timer8 module is enabled

bit 13 T7MD: Timer7 Module Disable bit

1 = Timer7 module is disabled

0 = Timer7 module is enabled

bit 12 T6MD: Timer6 Module Disable bit

1 = Timer6 module is disabled

0 = Timer6 module is enabled

bit 11-2 Unimplemented: Read as ‘0’

bit 1 I2C2MD: I2C2 Module Disable bit

1 = I2C2 module is disabled

0 = I2C2 module is enabled

bit 0 AD2MD: AD2 Module Disable bit(1)

1 = AD2 module is disabled

0 = AD2 module is enabled

Note 1: PCFGx bits have no effect if ADC module is disabled by setting this bit. In this case all port pins multi-

plexed with ANx will be in Digital mode.

dsPIC33FJXXXGPX06A/X08A/X10A

NOTES:

dsPIC33FJXXXGPX06A/X08A/X10A

11.0 I/O PORTS

All of the device pins (except VDD, VSS, MCLR and

OSC1/CLKIN) are shared between the peripherals and

the parallel I/O ports. All I/O input ports feature Schmitt

Trigger inputs for improved noise immunity.

11.1 Parallel I/O (PIO) Ports

A parallel I/O port that shares a pin with a peripheral is,

in general, subservient to the peripheral. The

peripheral’s output buffer data and control signals are

provided to a pair of multiplexers. The multiplexers

select whether the peripheral or the associated port

has ownership of the output data and control signals of

the I/O pin. The logic also prevents “loop through”, in

which a port’s digital output can drive the input of a

peripheral that shares the same pin. Figure 11-1 illus-

trates how ports are shared with other peripherals and

the associated I/O pin to which they are connected.

When a peripheral is enabled and actively driving an

associated pin, the use of the pin as a general purpose

output pin is disabled. The I/O pin may be read, but the

output driver for the parallel port bit will be disabled. If

a peripheral is enabled, but the peripheral is not

actively driving a pin, that pin may be driven by a port.

All port pins have three registers directly associated

with their operation as digital I/O. The data direction

or an output. If the data direction bit is a ‘1’, then the pin

is an input. All port pins are defined as inputs after a

Reset. Reads from the latch (LATx), read the latch.

Writes to the latch, write the latch. Reads from the port

(PORTx), read the port pins, while writes to the port

pins, write the latch.

Any bit and its associated data and control registers

that are not valid for a particular device will be

disabled. That means the corresponding LATx and

TRISx registers and the port pins will read as zeros.

When a pin is shared with another peripheral or

function that is defined as an input only, it is

nevertheless regarded as a dedicated port because

there is no other competing source of outputs. An

example is the INT4 pin.

FIGURE 11-1: BLOCK DIAGRAM OF A TYPICAL SHARED PORT STRUCTURE

Note 1: This data sheet summarizes the features

of the dsPIC33FJXXXGPX06A/X08A/

X10A family of devices. However, it is not

intended to be a comprehensive refer-

ence source. To complement the

information in this data sheet, refer to

Section 10. “I/O Ports” (DS70193) in

the “dsPIC33F/PIC24H Family

Reference Manual”, which is available

from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

WR LAT +

TRIS Latch

I/O Pin

WR PORT

Data Bus

Data Latch

Read Port

Read TRIS

WR TRIS

Peripheral Output Data

Output Enable

Peripheral Input Data

I/O

Peripheral Module

Peripheral Output Enable

PIO Module

Output Multiplexers

Output Data

Input Data

Peripheral Module Enable

Read LAT

dsPIC33FJXXXGPX06A/X08A/X10A

11.2 Open-Drain Configuration

In addition to the PORT, LAT and TRIS registers for

data control, some port pins can also be individually

configured for either digital or open-drain output. This is

controlled by the Open-Drain Control register, ODCx,

associated with each port. Setting any of the bits

configures the corresponding pin to act as an

open-drain output.

The open-drain feature allows the generation of

outputs higher than VDD (e.g., 5V) on any desired 5V

tolerant pins by using external pull-up resistors. The

maximum open-drain voltage allowed is the same as

the maximum VIH specification.

See the “Pin Diagrams” section for the available pins

and their functionality.

11.3 Configuring Analog Port Pins

The use of the ADxPCFGH, ADxPCFGL and TRIS

registers control the operation of the ADC port pins.

The port pins that are desired as analog inputs must

have their corresponding TRIS bit set (input). If the

TRIS bit is cleared (output), the digital output level (VOH

or VOL) is converted.

Clearing any bit in the ADxPCFGH or ADxPCFGL

analog pin. This is also the Reset state of any I/O pin

that has an analog (ANx) function associated with it.

When reading the PORT register, all pins configured as

analog input channels will read as cleared (a low level).

Pins configured as digital inputs will not convert an

analog input. Analog levels on any pin that is defined as

a digital input (including the ANx pins) can cause the

input buffer to consume current that exceeds the

device specifications.

11.4 I/O Port Write/Read Timing

One instruction cycle is required between a port

direction change or port write operation and a read

operation of the same port. Typically, this instruction

would be a NOP.

11.5 Input Change Notification

The input change notification function of the I/O ports

allows the dsPIC33FJXXXGPX06A/X08A/X10A

devices to generate interrupt requests to the processor

in response to a change-of-state on selected input pins.

This feature is capable of detecting input

change-of-states even in Sleep mode, when the clocks

are disabled. Depending on the device pin count, there

are up to 24 external signals (CN0 through CN23) that

can be selected (enabled) for generating an interrupt

request on a change-of-state.

There are four control registers associated with the CN

module. The CNEN1 and CNEN2 registers contain the

CN interrupt enable (CNxIE) control bits for each of the

CN input pins. Setting any of these bits enables a CN

interrupt for the corresponding pins.

Each CN pin also has a weak pull-up connected to it.

The pull-ups act as a current source that is connected

to the pin and eliminate the need for external resistors

when push button or keypad devices are connected.

The pull-ups are enabled separately using the CNPU1

and CNPU2 registers, which contain the weak pull-up

enable (CNxPUE) bits for each of the CN pins. Setting

any of the control bits enables the weak pull-ups for the

corresponding pins.

EXAMPLE 11-1: PORT WRITE/READ EXAMPLE

Note: In devices with two ADC modules, if the

corresponding PCFG bit in either

AD1PCFGH(L) and AD2PCFGH(L) is

cleared, the pin is configured as an analog

input.

Note: The voltage on an analog input pin can be

between -0.3V to (VDD + 0.3 V).

Note: Pull-ups on change notification pins

should always be disabled whenever the

port pin is configured as a digital output.

MOV 0xFF00, W0 ; Configure PORTB<15:8> as inputs

MOV W0, TRISBB ; and PORTB<7:0> as outputs

NOP ; Delay 1 cycle

btss PORTB, #13 ; Next Instruction

dsPIC33FJXXXGPX06A/X08A/X10A

12.0 TIMER1

The Timer1 module is a 16-bit timer, which can serve

as the time counter for the real-time clock, or operate

as a free-running interval timer/counter. Timer1 can

operate in three modes:

• 16-bit Timer

• 16-bit Synchronous Counter

• 16-bit Asynchronous Counter

Timer1 also supports these features:

• Timer gate operation

• Selectable prescaler settings

• Timer operation during CPU Idle and Sleep

modes

• Interrupt on 16-bit Period register match or falling

edge of external gate signal

Figure 12-1 presents a block diagram of the 16-bit

timer module.

To configure Timer1 for operation:

1. Set the TON bit (= 1) in the T1CON register.

2. Select the timer prescaler ratio using the

TCKPS<1:0> bits in the T1CON register.

3. Set the Clock and Gating modes using the TCS

and TGATE bits in the T1CON register.

4. Set or clear the TSYNC bit in T1CON to select

synchronous or asynchronous operation.

5. Load the timer period value into the PR1

6. If interrupts are required, set the interrupt enable

bit, T1IE. Use the priority bits, T1IP<2:0>, to set

the interrupt priority.

FIGURE 12-1: 16-BIT TIMER1 MODULE BLOCK DIAGRAM

Note 1: This data sheet summarizes the features

of the dsPIC33FJXXXGPX06A/X08A/

X10A family of devices. However, it is not

intended to be a comprehensive

reference source. To complement the

information in this data sheet, refer to

Section 11. “Timers” (DS70205) in the

“dsPIC33F/PIC24H Family Reference

Manual”, which is available from the

Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

TON

SOSCI

SOSCO/

PR1

Set T1IF

Equal

Comparator

TMR1

Reset

SOSCEN

TSYNC

TCKPS<1:0>

Prescaler

1, 8, 64, 256

TGATE

TCY

T1CK

TCS

TGATE

Sync

Gate

Sync

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0

TON —TSIDL— — — — —

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 U-0

— TGATE TCKPS<1:0> —TSYNCTCS —

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 TON: Timer1 On bit

1 = Starts 16-bit Timer1

0 = Stops 16-bit Timer1

bit 14 Unimplemented: Read as ‘0’

bit 13 TSIDL: Stop in Idle Mode bit

1 = Discontinue module operation when device enters Idle mode

0 = Continue module operation in Idle mode

bit 12-7 Unimplemented: Read as ‘0’

bit 6 TGATE: Timer1 Gated Time Accumulation Enable bit

When TCS = 1:

This bit is ignored.

When TCS = 0:

1 = Gated time accumulation enabled

0 = Gated time accumulation disabled

bit 5-4 TCKPS<1:0>: Timer1 Input Clock Prescale Select bits

11 = 1:256

10 = 1:64

01 = 1:8

00 = 1:1

bit 3 Unimplemented: Read as ‘0’

bit 2 TSYNC: Timer1 External Clock Input Synchronization Select bit

When TCS = 1:

1 = Synchronize external clock input

0 = Do not synchronize external clock input

When TCS = 0:

This bit is ignored.

bit 1 TCS: Timer1 Clock Source Select bit

1 = External clock from pin T1CK (on the rising edge)

0 = Internal clock (FCY)

bit 0 Unimplemented: Read as ‘0’

dsPIC33FJXXXGPX06A/X08A/X10A

13.0 TIMER2/3, TIMER4/5, TIMER6/7

AND TIMER8/9

The Timer2/3, Timer4/5, Timer6/7 and Timer8/9

modules are 32-bit timers, which can also be

configured as four independent 16-bit timers with

selectable operating modes.

As a 32-bit timer, Timer2/3, Timer4/5, Timer6/7 and

Timer8/9 operate in three modes:

• Two Independent 16-bit Timers (e.g., Timer2 and

Timer3) with all 16-bit operating modes (except

Asynchronous Counter mode)

• Single 32-bit Timer

• Single 32-bit Synchronous Counter

They also support these features:

• Timer Gate Operation

• Selectable Prescaler Settings

• Timer Operation during Idle and Sleep modes

• Interrupt on a 32-bit Period Register Match

• Time Base for Input Capture and Output Compare

Modules (Timer2 and Timer3 only)

• ADC1 Event Trigger (Timer2/3 only)

• ADC2 Event Trigger (Timer4/5 only)

Individually, all eight of the 16-bit timers can function as

synchronous timers or counters. They also offer the

features listed above, except for the event trigger; this

is implemented only with Timer2/3. The operating

modes and enabled features are determined by setting

the appropriate bit(s) in the T2CON, T3CON, T4CON,

T5CON, T6CON, T7CON, T8CON and T9CON

registers. T2CON, T4CON, T6CON and T8CON are

shown in generic form in Register 13-1. T3CON,

T5CON, T7CON and T9CON are shown in

For 32-bit timer/counter operation, Timer2, Timer4,

Timer6 or Timer8 is the least significant word; Timer3,

Timer5, Timer7 or Timer9 is the most significant word

of the 32-bit timers.

To configure Timer2/3, Timer4/5, Timer6/7 or Timer8/9

for 32-bit operation:

1. Set the corresponding T32 control bit.

2. Select the prescaler ratio for Timer2, Timer4,

Timer6 or Timer8 using the TCKPS<1:0> bits.

3. Set the Clock and Gating modes using the

corresponding TCS and TGATE bits.

4. Load the timer period value. PR3, PR5, PR7 or

PR9 contains the most significant word of the

value, while PR2, PR4, PR6 or PR8 contains the

least significant word.

5. If interrupts are required, set the interrupt enable

bit, T3IE, T5IE, T7IE or T9IE. Use the priority

bits, T3IP<2:0>, T5IP<2:0>, T7IP<2:0> or

T9IP<2:0>, to set the interrupt priority. While

Timer2, Timer4, Timer6 or Timer8 control the

timer, the interrupt appears as a Timer3, Timer5,

Timer7 or Timer9 interrupt.

6. Set the corresponding TON bit.

The timer value at any point is stored in the register

pair, TMR3:TMR2, TMR5:TMR4, TMR7:TMR6 or

TMR9:TMR8. TMR3, TMR5, TMR7 or TMR9 always

contains the most significant word of the count, while

TMR2, TMR4, TMR6 or TMR8 contains the least

significant word.

To configure any of the timers for individual 16-bit

operation:

1. Clear the T32 bit corresponding to that timer.

2. Select the timer prescaler ratio using the

TCKPS<1:0> bits.

3. Set the Clock and Gating modes using the TCS

and TGATE bits.

4. Load the timer period value into the PRx

5. If interrupts are required, set the interrupt enable

bit, TxIE. Use the priority bits, TxIP<2:0>, to set

the interrupt priority.

6. Set the TON bit.

A block diagram for a 32-bit timer pair (Timer4/5)

example is shown in Figure 13-1 and a timer (Timer4)

operating in 16-bit mode example is shown in

Figure 13-2.

Note 1: This data sheet summarizes the fea-

tures of the dsPIC33FJXXXGPX06A/

X08A/X10A family of devices. How-

ever, it is not intended to be a compre-

hensive reference source. To

complement the information in this data

sheet, refer to Section 11. “Timers”

(DS70205) in the “dsPIC33F/PIC24H

Family Reference Manual”, which is

available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Note: For 32-bit operation, T3CON, T5CON,

T7CON and T9CON control bits are

ignored. Only T2CON, T4CON, T6CON

and T8CON control bits are used for setup

and control. Timer2, Timer4, Timer6 and

Timer8 clock and gate inputs are utilized

for the 32-bit timer modules, but an

interrupt is generated with the Timer3,

Timer5, Ttimer7 and Timer9 interrupt

flags.

Note: Only Timer2 and Timer3 can trigger a

DMA data transfer.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 13-1: TIMER2/3 (32-BIT) BLOCK DIAGRAM(1)

Set T3IF

Equal Comparator

PR3 PR2

Reset

LSbMSb

Note 1: The 32-bit timer control bit, T32, must be set for 32-bit timer/counter operation. All control bits are respective

to the T2CON register.

2: The ADC event trigger is available only on Timer2/3.

Data Bus<15:0>

TMR3HLD

Read TMR2

Write TMR2 16

TGATE

TON

TCKPS<1:0>

TCY

TCS

TGATE

T2CK

ADC Event Trigger(2)

Gate

Sync

Prescaler

1, 8, 64, 256

Sync

TMR3 TMR2

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 13-2: TIMER2 (16-BIT) BLOCK DIAGRAM

TON

TCKPS<1:0>

Prescaler

1, 8, 64, 256

TCY TCS

TGATE

T2CK

PR2

Set T2IF

Equal

Comparator

TMR2

Reset

TGATE

Gate

Sync

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0

TON —TSIDL— — — — —

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 U-0

— TGATE TCKPS<1:0> T32 —TCS

(1) —

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 TON: Timerx On bit

When T32 = 1:

1 = Starts 32-bit Timerx/y

0 = Stops 32-bit Timerx/y

When T32 = 0:

1 = Starts 16-bit Timerx

0 = Stops 16-bit Timerx

bit 14 Unimplemented: Read as ‘0’

bit 13 TSIDL: Stop in Idle Mode bit

1 = Discontinue module operation when device enters Idle mode

0 = Continue module operation in Idle mode

bit 12-7 Unimplemented: Read as ‘0’

bit 6 TGATE: Timerx Gated Time Accumulation Enable bit

When TCS = 1:

This bit is ignored.

When TCS = 0:

1 = Gated time accumulation enabled

0 = Gated time accumulation disabled

bit 5-4 TCKPS<1:0>: Timerx Input Clock Prescale Select bits

11 = 1:256

10 = 1:64

01 = 1:8

00 = 1:1

bit 3 T32: 32-bit Timer Mode Select bit

1 = Timerx and Timery form a single 32-bit timer

0 = Timerx and Timery act as two 16-bit timers

bit 2 Unimplemented: Read as ‘0’

bit 1 TCS: Timerx Clock Source Select bit(1)

1 = External clock from pin TxCK (on the rising edge)

0 = Internal clock (FCY)

bit 0 Unimplemented: Read as ‘0’

Note 1: The TxCK pin is not available on all timers. Refer to the “Pin Diagrams” section for the available pins.

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0

TON(1) —TSIDL

(2) — — — — —

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 U-0 U-0 R/W-0 U-0

—TGATE

(1) TCKPS<1:0>(1) ——TCS

(1,3) —

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 TON: Timery On bit(1)

1 = Starts 16-bit Timery

0 = Stops 16-bit Timery

bit 14 Unimplemented: Read as ‘0’

bit 13 TSIDL: Stop in Idle Mode bit(2)

1 = Discontinue module operation when device enters Idle mode

0 = Continue module operation in Idle mode

bit 12-7 Unimplemented: Read as ‘0’

bit 6 TGATE: Timery Gated Time Accumulation Enable bit(1)

When TCS = 1:

This bit is ignored.

When TCS = 0:

1 = Gated time accumulation enabled

0 = Gated time accumulation disabled

bit 5-4 TCKPS<1:0>: Timer3 Input Clock Prescale Select bits(1)

11 = 1:256

10 = 1:64

01 = 1:8

00 = 1:1

bit 3-2 Unimplemented: Read as ‘0’

bit 1 TCS: Timery Clock Source Select bit(1,3)

1 = External clock from pin TyCK (on the rising edge)

0 = Internal clock (FCY)

bit 0 Unimplemented: Read as ‘0’

Note 1: When 32-bit operation is enabled (T2CON<3> = 1), these bits have no effect on Timery operation; all timer

functions are set through T2CON.

2: When 32-bit timer operation is enabled (T32 = 1) in the Timer Control register (TxCON<3>), the TSIDL bit

must be cleared to operate the 32-bit timer in Idle mode.

3: The TyCK pin is not available on all timers. Refer to the “Pin Diagrams” section for the available pins.

dsPIC33FJXXXGPX06A/X08A/X10A

NOTES:

dsPIC33FJXXXGPX06A/X08A/X10A

14.0 INPUT CAPTURE

The input capture module is useful in applications

requiring frequency (period) and pulse measurement.

The dsPIC33FJXXXGPX06A/X08A/X10A devices

support up to eight input capture channels.

The input capture module captures the 16-bit value of

the selected Time Base register when an event occurs

at the ICx pin. The events that cause a capture event

are listed below in three categories:

• Simple Capture Event modes:

- Capture timer value on every falling edge of

input at ICx pin

- Capture timer value on every rising edge of

input at ICx pin

• Capture timer value on every edge (rising and fall-

ing)

• Prescaler Capture Event modes:

- Capture timer value on every 4th rising

edge of input at ICx pin

- Capture timer value on every 16th rising

edge of input at ICx pin

Each input capture channel can select between one of

two 16-bit timers (Timer2 or Timer3) for the time base.

The selected timer can use either an internal or exter-

nal clock.

Other operational features include:

• Device wake-up from capture pin during CPU

Sleep and Idle modes

• Interrupt on input capture event

• 4-word FIFO buffer for capture values

- Interrupt optionally generated after 1, 2, 3 or

4 buffer locations are filled

• Input capture can also be used to provide

additional sources of external interrupts

FIGURE 14-1: INPUT CAPTURE BLOCK DIAGRAM

Note 1: This data sheet summarizes the fea-

tures of the dsPIC33FJXXXGPX06A/

X08A/X10A family of devices. How-

ever, it is not intended to be a compre-

hensive reference source. To

complement the information in this data

sheet, refer to Section 12. “Input

Capture” (DS70198) in the “dsPIC33F/

PIC24H Family Reference Manual”,

which is available from the Microchip

web site (www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Note: Only IC1 and IC2 can trigger a DMA data

transfer. If DMA data transfers are

required, the FIFO buffer size must be set

to 1 (ICI<1:0> = 00).

ICxBUF

ICx Pin

ICM<2:0> (ICxCON<2:0>)

Mode Select

Set Flag ICxIF

(in IFSn Register)

TMRy TMRz

Edge Detection Logic

16 16

FIFO

R/W

Logic

ICxI<1:0>

ICOV, ICBNE (ICxCON<4:3>)

ICxCON

Interrupt

Logic

System Bus

From 16-bit Timers

ICTMR

(ICxCON<7>)

FIFO

Prescaler

Counter

(1, 4, 16) and

Clock Synchronizer

Note: An ‘x’ in a signal, register or bit name denotes the number of the capture channel.

dsPIC33FJXXXGPX06A/X08A/X10A

14.1 Input Capture Registers

U-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0

——ICSIDL— — — — —

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R-0, HC R-0, HC R/W-0 R/W-0 R/W-0

ICTMR(1) ICI<1:0> ICOV ICBNE ICM<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13 ICSIDL: Input Capture Module Stop in Idle Control bit

1 = Input capture module will halt in CPU Idle mode

0 = Input capture module will continue to operate in CPU Idle mode

bit 12-8 Unimplemented: Read as ‘0’

bit 7 ICTMR: Input Capture Timer Select bits(1)

1 = TMR2 contents are captured on capture event

0 = TMR3 contents are captured on capture event

bit 6-5 ICI<1:0>: Select Number of Captures per Interrupt bits

11 = Interrupt on every fourth capture event

10 = Interrupt on every third capture event

01 = Interrupt on every second capture event

00 = Interrupt on every capture event

bit 4 ICOV: Input Capture Overflow Status Flag bit (read-only)

1 = Input capture overflow occurred

0 = No input capture overflow occurred

bit 3 ICBNE: Input Capture Buffer Empty Status bit (read-only)

1 = Input capture buffer is not empty, at least one more capture value can be read

0 = Input capture buffer is empty

bit 2-0 ICM<2:0>: Input Capture Mode Select bits

111 = Input capture functions as interrupt pin only when device is in Sleep or Idle mode

(Rising edge detect only, all other control bits are not applicable.)

110 = Unused (module disabled)

101 = Capture mode, every 16th rising edge

100 = Capture mode, every 4th rising edge

011 = Capture mode, every rising edge

010 = Capture mode, every falling edge

001 = Capture mode, every edge (rising and falling)

(ICI<1:0> bits do not control interrupt generation for this mode.)

000 = Input capture module turned off

dsPIC33FJXXXGPX06A/X08A/X10A

15.0 OUTPUT COMPARE The output compare module can select either Timer2 or

Timer3 for its time base. The module compares the

value of the timer with the value of one or two Compare

registers depending on the operating mode selected.

The state of the output pin changes when the timer

value matches the Compare register value. The output

compare module generates either a single output

pulse, or a sequence of output pulses, by changing the

state of the output pin on the compare match events.

The output compare module can also generate

interrupts on compare match events.

The output compare module has multiple operating

modes:

• Active-Low One-Shot mode

• Active-High One-Shot mode

• Toggle mode

• Delayed One-Shot mode

• Continuous Pulse mode

• PWM mode without Fault Protection

• PWM mode with Fault Protection

FIGURE 15-1: OUTPUT COMPARE MODULE BLOCK DIAGRAM

Note 1: This data sheet summarizes the fea-

tures of the dsPIC33FJXXXGPX06A/

X08A/X10A families of devices. It is not

intended to be a comprehensive refer-

ence source. To complement the infor-

mation in this data sheet, refer to

Section 13. “Output Compare”

(DS70209) of the “dsPIC33F/PIC24H

Family Reference Manual”, which is

available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

OCxR

Comparator

Output

Logic

OCM<2:0>

OCx

Set Flag bit

OCxIF

OCxRS

Mode Select

OCTSEL 01

OCFA

TMR2 TMR2

TMR3 TMR3

Rollover Rollover

Output

Logic

Output

Enable Enable

dsPIC33FJXXXGPX06A/X08A/X10A

15.1 Output Compare Modes

Configure the Output Compare modes by setting the

appropriate Output Compare Mode (OCM<2:0>) bits in

the Output Compare Control (OCxCON<2:0>) register.

Table 15-1 lists the different bit settings for the Output

Compare modes. Figure 15-2 illustrates the output

compare operation for various modes. The user

application must disable the associated timer when

writing to the Output Compare Control registers to

avoid malfunctions.

TABLE 15-1: OUTPUT COMPARE MODES

FIGURE 15-2: OUTPUT COMPARE OPERATION

Note: See Section 13. “Output Compare”

(DS70209) in the “dsPIC33F/PIC24H

Family Reference Manual” for OCxR and

OCxRS register restrictions.

OCM<2:0> Mode OCx Pin Initial State OCx Interrupt Generation

000 Module Disabled Controlled by GPIO register —

001 Active-Low One-Shot 0OCx rising edge

010 Active-High One-Shot 1OCx falling edge

011 Toggle Current output is maintained OCx rising and falling edge

100 Delayed One-Shot 0OCx falling edge

101 Continuous Pulse 0OCx falling edge

110 PWM without Fault Protection ‘0’, if OCxR is zero

‘1’, if OCxR is non-zero

No interrupt

111 PWM with Fault Protection ‘0’, if OCxR is zero

‘1’, if OCxR is non-zero

OCFA falling edge for OC1 to OC4

OCxRS

TMRy

OCxR

Timer is Reset on

Period Match

Continuous Pulse

(OCM = 101)

PWM

(OCM = 110 or 111)

Active-Low One-Shot

(OCM = 001)

Active-High One-Shot

(OCM = 010)

Toggle

(OCM = 011)

Delayed One-Shot

(OCM = 100)

Output Compare

Mode Enabled

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0

——OCSIDL — — — — —

bit 15 bit 8

U-0 U-0 U-0 R-0, HC R/W-0 R/W-0 R/W-0 R/W-0

— — — OCFLT OCTSEL OCM<2:0>

bit 7 bit 0

Legend: HC = Hardware Clearable bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13 OCSIDL: Stop Output Compare in Idle Mode Control bit

1 = Output Compare x halts in CPU Idle mode

0 = Output Compare x continues to operate in CPU Idle mode

bit 12-5 Unimplemented: Read as ‘0’

bit 4 OCFLT: PWM Fault Condition Status bit

1 = PWM Fault condition has occurred (cleared in hardware only)

0 = No PWM Fault condition has occurred (this bit is only used when OCM<2:0> = 111)

bit 3 OCTSEL: Output Compare Timer Select bit

1 = Timer3 is the clock source for Compare x

0 = Timer2 is the clock source for Compare x

bit 2-0 OCM<2:0>: Output Compare Mode Select bits

111 = PWM mode on OCx, Fault pin enabled

110 = PWM mode on OCx, Fault pin disabled

101 = Initialize OCx pin low, generate continuous output pulses on OCx pin

100 = Initialize OCx pin low, generate single output pulse on OCx pin

011 = Compare event toggles OCx pin

010 = Initialize OCx pin high, compare event forces OCx pin low

001 = Initialize OCx pin low, compare event forces OCx pin high

000 = Output compare channel is disabled

dsPIC33FJXXXGPX06A/X08A/X10A

NOTES:

dsPIC33FJXXXGPX06A/X08A/X10A

16.0 SERIAL PERIPHERAL

INTERFACE (SPI)

The Serial Peripheral Interface (SPI) module is a

synchronous serial interface useful for communicating

with other peripheral or microcontroller devices. These

peripheral devices may be serial EEPROMs, shift

registers, display drivers, Analog-to-Digital Converters

(ADC), etc. The SPI module is compatible with SPI and

SIOP from Motorola®.

Each SPI module consists of a 16-bit shift register,

SPIxSR (where x = 1 or 2), used for shifting data in and

out, and a buffer register, SPIxBUF. A control register,

SPIxCON, configures the module. Additionally, a status

The serial interface consists of 4 pins: SDIx (serial data

input), SDOx (serial data output), SCKx (shift clock input

or output), and SSx (active-low slave select).

In Master mode operation, SCK is a clock output but in

Slave mode, it is a clock input.

FIGURE 16-1: SPI MODULE BLOCK DIAGRAM

Note 1: This data sheet summarizes the features

of the dsPIC33FJXXXGPX06A/X08A/

X10A family of devices. However, it is not

intended to be a comprehensive refer-

ence source. To complement the infor-

mation in this data sheet, refer to Section

18. “Serial Peripheral Interface (SPI)”

(DS70206) in the “dsPIC33F/PIC24H

Family Reference Manual”, which is

available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Note: In this section, the SPI modules are

referred to together as SPIx, or

separately as SPI1 and SPI2. Special

Function Registers will follow a similar

notation. For example, SPIxCON refers to

the control register for the SPI1 or SPI2

module.

Internal Data Bus

SDIx

SDOx

SSx

SCKx

SPIxSR

bit 0

Shift Control

Edge

Select

FCY

Primary

1:1/4/16/64

Enable

Prescaler

Sync

SPIxBUF

Control

Transfer

Write SPIxBUF

Read SPIxBUF

SPIxCON1<1:0>

SPIxCON1<4:2>

Master Clock

Clock

Control

Secondary

Prescaler

1:1 to 1:8

SPIxRXB SPIxTXB

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0

SPIEN — SPISIDL — — — — —

bit 15 bit 8

U-0 R/C-0 U-0 U-0 U-0 U-0 R-0 R-0

— SPIROV — — — — SPITBF SPIRBF

bit 7 bit 0

Legend: C = Clearable bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 SPIEN: SPIx Enable bit

1 = Enables module and configures SCKx, SDOx, SDIx and SSx as serial port pins

0 = Disables module

bit 14 Unimplemented: Read as ‘0’

bit 13 SPISIDL: Stop in Idle Mode bit

1 = Discontinue module operation when device enters Idle mode

0 = Continue module operation in Idle mode

bit 12-7 Unimplemented: Read as ‘0’

bit 6 SPIROV: Receive Overflow Flag bit

1 = A new byte/word is completely received and discarded. The user software has not read the

previous data in the SPIxBUF register

0 = No overflow has occurred

bit 5-2 Unimplemented: Read as ‘0’

bit 1 SPITBF: SPIx Transmit Buffer Full Status bit

1 = Transmit not yet started, SPIxTXB is full

0 = Transmit started, SPIxTXB is empty

Automatically set in hardware when CPU writes SPIxBUF location, loading SPIxTXB.

Automatically cleared in hardware when SPIx module transfers data from SPIxTXB to SPIxSR.

bit 0 SPIRBF: SPIx Receive Buffer Full Status bit

1 = Receive complete, SPIxRXB is full

0 = Receive is not complete, SPIxRXB is empty

Automatically set in hardware when SPIx transfers data from SPIxSR to SPIxRXB.

Automatically cleared in hardware when core reads SPIxBUF location, reading SPIxRXB.

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— — — DISSCK DISSDO MODE16 SMP CKE(1)

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SSEN(3) CKP MSTEN SPRE<2:0>(2) PPRE<1:0>(2)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-13 Unimplemented: Read as ‘0’

bit 12 DISSCK: Disable SCKx pin bit (SPI Master modes only)

1 = Internal SPI clock is disabled, pin functions as I/O

0 = Internal SPI clock is enabled

bit 11 DISSDO: Disable SDOx pin bit

1 = SDOx pin is not used by module; pin functions as I/O

0 = SDOx pin is controlled by the module

bit 10 MODE16: Word/Byte Communication Select bit

1 = Communication is word-wide (16 bits)

0 = Communication is byte-wide (8 bits)

bit 9 SMP: SPIx Data Input Sample Phase bit

Master mode:

1 = Input data sampled at end of data output time

0 = Input data sampled at middle of data output time

Slave mode:

SMP must be cleared when SPIx is used in Slave mode.

bit 8 CKE: SPIx Clock Edge Select bit(1)

1 = Serial output data changes on transition from active clock state to Idle clock state (see bit 6)

0 = Serial output data changes on transition from Idle clock state to active clock state (see bit 6)

bit 7 SSEN: Slave Select Enable bit (Slave mode)(3)

1 = SSx pin used for Slave mode

0 = SSx pin not used by module. Pin controlled by port function

bit 6 CKP: Clock Polarity Select bit

1 = Idle state for clock is a high level; active state is a low level

0 = Idle state for clock is a low level; active state is a high level

bit 5 MSTEN: Master Mode Enable bit

1 = Master mode

0 = Slave mode

Note 1: The CKE bit is not used in the Framed SPI modes. The user should program this bit to ‘0’ for the Framed

SPI modes (FRMEN = 1).

2: Do not set both Primary and Secondary prescalers to a value of 1:1.

3: This bit must be cleared when FRMEN = 1.

dsPIC33FJXXXGPX06A/X08A/X10A

bit 4-2 SPRE<2:0>: Secondary Prescale bits (Master mode)(2)

111 = Secondary prescale 1:1

110 = Secondary prescale 2:1

•

000 = Secondary prescale 8:1

bit 1-0 PPRE<1:0>: Primary Prescale bits (Master mode)(2)

11 = Primary prescale 1:1

10 = Primary prescale 4:1

01 = Primary prescale 16:1

00 = Primary prescale 64:1

Note 1: The CKE bit is not used in the Framed SPI modes. The user should program this bit to ‘0’ for the Framed

SPI modes (FRMEN = 1).

2: Do not set both Primary and Secondary prescalers to a value of 1:1.

3: This bit must be cleared when FRMEN = 1.

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 U-0 U-0

FRMEN SPIFSD FRMPOL — — — — —

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 U-0

— — — — — — FRMDLY —

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 FRMEN: Framed SPIx Support bit

1 = Framed SPIx support enabled (SSx pin used as frame sync pulse input/output)

0 = Framed SPIx support disabled

bit 14 SPIFSD: Frame Sync Pulse Direction Control bit

1 = Frame sync pulse input (slave)

0 = Frame sync pulse output (master)

bit 13 FRMPOL: Frame Sync Pulse Polarity bit

1 = Frame sync pulse is active-high

0 = Frame sync pulse is active-low

bit 12-2 Unimplemented: Read as ‘0’

bit 1 FRMDLY: Frame Sync Pulse Edge Select bit

1 = Frame sync pulse coincides with first bit clock

0 = Frame sync pulse precedes first bit clock

bit 0 Unimplemented: Read as ‘0’

This bit must not be set to ‘1’ by the user application.

dsPIC33FJXXXGPX06A/X08A/X10A

NOTES:

dsPIC33FJXXXGPX06A/X08A/X10A

17.0 INTER-INTEGRATED

CIRCUIT™ (I2C™)

The Inter-Integrated Circuit (I2C) module provides

complete hardware support for both Slave and

Multi-Master modes of the I2C serial communication

standard, with a 16-bit interface.

The dsPIC33FJXXXGPX06A/X08A/X10A devices

have up to two I2C interface modules, denoted as I2C1

and I2C2. Each I2C module has a 2-pin interface: the

SCLx pin is clock and the SDAx pin is data.

Each I2C module ‘x’ (x = 1 or 2) offers the following key

features:

•I

2C interface supporting both master and slave

operation

•I

2C Slave mode supports 7-bit and 10-bit

addressing

•I

2C Master mode supports 7-bit and 10-bit

addressing

•I

2C Port allows bidirectional transfers between

master and slaves

• Serial clock synchronization for I2C port can be

used as a handshake mechanism to suspend and

resume serial transfer (SCLREL control)

•I

2C supports multi-master operation; detects bus

collision and will arbitrate accordingly

17.1 Operating Modes

The hardware fully implements all the master and slave

functions of the I2C Standard and Fast mode

specifications, as well as 7 and 10-bit addressing.

The I2C module can operate either as a slave or a

master on an I2C bus.

The following types of I2C operation are supported:

•I

2C slave operation with 7-bit addressing

•I

2C slave operation with 10-bit addressing

•I

2C master operation with 7-bit or 10-bit addressing

For details about the communication sequence in each

of these modes, please refer to the “dsPIC33F/PIC24H

Family Reference Manual”.

17.2 I2C Registers

I2CxCON and I2CxSTAT are control and status

registers, respectively. The I2CxCON register is

readable and writable. The lower six bits of I2CxSTAT

are read-only. The remaining bits of the I2CSTAT are

read/write.

I2CxRSR is the shift register used for shifting data,

whereas I2CxRCV is the buffer register to which data

bytes are written, or from which data bytes are read.

I2CxRCV is the receive buffer. I2CxTRN is the transmit

operation.

The I2CxADD register holds the slave address. A

status bit, ADD10, indicates 10-bit Address mode. The

I2CxBRG acts as the Baud Rate Generator (BRG)

reload value.

In receive operations, I2CxRSR and I2CxRCV together

form a double-buffered receiver. When I2CxRSR

receives a complete byte, it is transferred to I2CxRCV

and an interrupt pulse is generated.

Note 1: This data sheet summarizes the features

of the dsPIC33FJXXXGPX06A/X08A/

X10A family of devices. However, it is not

intended to be a comprehensive refer-

ence source. To complement the infor-

mation in this data sheet, refer to Section

19. “Inter-Integrated Circuit™ (I2C™)”

(DS70195) in the “dsPIC33F/PIC24H

Family Reference Manual”, which is

available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 17-1: I2C™ BLOCK DIAGRAM (X = 1 OR 2)

Internal

Data Bus

SCLx

SDAx

Shift

Match Detect

I2CxADD

Start and Stop

Bit Detect

Clock

Address Match

Clock

Stretching

I2CxTRN

LSb

Shift Clock

BRG Down Counter

Reload

Control

TCY/2

Start and Stop

Bit Generation

Acknowledge

Generation

Collision

Detect

I2CxCON

I2CxSTAT

Control Logic

Read

LSb

Write

Read

I2CxBRG

I2CxRSR

Write

Read

Write

Read

Write

Read

Write

Read

Write

Read

I2CxMSK

I2CxRCV

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 U-0 R/W-0 R/W-1 HC R/W-0 R/W-0 R/W-0 R/W-0

I2CEN — I2CSIDL SCLREL IPMIEN A10M DISSLW SMEN

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 HC R/W-0 HC R/W-0 HC R/W-0 HC R/W-0 HC

GCEN STREN ACKDT ACKEN RCEN PEN RSEN SEN

bit 7 bit 0

Legend: U = Unimplemented bit, read as ‘0’

R = Readable bit W = Writable bit HS = Set in hardware HC = Cleared in hardware

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 I2CEN: I2Cx Enable bit

1 = Enables the I2Cx module and configures the SDAx and SCLx pins as serial port pins

0 = Disables the I2Cx module. All I2C pins are controlled by port functions

bit 14 Unimplemented: Read as ‘0’

bit 13 I2CSIDL: Stop in Idle Mode bit

1 = Discontinue module operation when device enters an Idle mode

0 = Continue module operation in Idle mode

bit 12 SCLREL: SCLx Release Control bit (when operating as I2C slave)

1 = Release SCLx clock

0 = Hold SCLx clock low (clock stretch)

If STREN = 1:

Bit is R/W (i.e., software may write ‘0’ to initiate stretch and write ‘1’ to release clock). Hardware clear

at beginning of slave transmission. Hardware clear at end of slave reception.

If STREN = 0:

Bit is R/S (i.e., software may only write ‘1’ to release clock). Hardware clear at beginning of slave

transmission.

bit 11 IPMIEN: Intelligent Peripheral Management Interface (IPMI) Enable bit

1 = IPMI mode is enabled; all addresses Acknowledged

0 = IPMI mode disabled

bit 10 A10M: 10-bit Slave Address bit

1 = I2CxADD is a 10-bit slave address

0 = I2CxADD is a 7-bit slave address

bit 9 DISSLW: Disable Slew Rate Control bit

1 = Slew rate control disabled

0 = Slew rate control enabled

bit 8 SMEN: SMBus Input Levels bit

1 = Enable I/O pin thresholds compliant with SMBus specification

0 = Disable SMBus input thresholds

bit 7 GCEN: General Call Enable bit (when operating as I2C slave)

1 = Enable interrupt when a general call address is received in the I2CxRSR

(module is enabled for reception)

0 = General call address disabled

bit 6 STREN: SCLx Clock Stretch Enable bit (when operating as I2C slave)

Used in conjunction with SCLREL bit.

1 = Enable software or receive clock stretching

0 = Disable software or receive clock stretching

dsPIC33FJXXXGPX06A/X08A/X10A

bit 5 ACKDT: Acknowledge Data bit (when operating as I2C master, applicable during master receive)

Value that will be transmitted when the software initiates an Acknowledge sequence.

1 = Send NACK during Acknowledge

0 = Send ACK during Acknowledge

bit 4 ACKEN: Acknowledge Sequence Enable bit

(when operating as I2C master, applicable during master receive)

1 = Initiate Acknowledge sequence on SDAx and SCLx pins and transmit ACKDT data bit.

Hardware clear at end of master Acknowledge sequence

0 = Acknowledge sequence not in progress

bit 3 RCEN: Receive Enable bit (when operating as I2C master)

1 = Enables Receive mode for I2C. Hardware clear at end of eighth bit of master receive data byte

0 = Receive sequence not in progress

bit 2 PEN: Stop Condition Enable bit (when operating as I2C master)

1 = Initiate Stop condition on SDAx and SCLx pins. Hardware clear at end of master Stop sequence

0 = Stop condition not in progress

bit 1 RSEN: Repeated Start Condition Enable bit (when operating as I2C master)

1 = Initiate Repeated Start condition on SDAx and SCLx pins. Hardware clear at end of

master Repeated Start sequence

0 = Repeated Start condition not in progress

bit 0 SEN: Start Condition Enable bit (when operating as I2C master)

1 = Initiate Start condition on SDAx and SCLx pins. Hardware clear at end of master Start sequence

0 = Start condition not in progress

dsPIC33FJXXXGPX06A/X08A/X10A

R-0 HSC R-0 HSC U-0 U-0 U-0 R/C-0 HS R-0 HSC R-0 HSC

ACKSTAT TRSTAT — — — BCL GCSTAT ADD10

bit 15 bit 8

R/C-0 HS R/C-0 HS R-0 HSC R/C-0 HSC R/C-0 HSC R-0 HSC R-0 HSC R-0 HSC

IWCOL I2COV D_A P S R_W RBF TBF

bit 7 bit 0

Legend: U = Unimplemented bit, read as ‘0’ C = Clear only bit

R = Readable bit W = Writable bit HS = Set in hardware HSC = Hardware set/cleared

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 ACKSTAT: Acknowledge Status bit

(when operating as I2C master, applicable to master transmit operation)

1 = NACK received from slave

0 = ACK received from slave

Hardware set or clear at end of slave Acknowledge.

bit 14 TRSTAT: Transmit Status bit (when operating as I2C master, applicable to master transmit operation)

1 = Master transmit is in progress (8 bits + ACK)

0 = Master transmit is not in progress

Hardware set at beginning of master transmission. Hardware clear at end of slave Acknowledge.

bit 13-11 Unimplemented: Read as ‘0’

bit 10 BCL: Master Bus Collision Detect bit

1 = A bus collision has been detected during a master operation

0 = No collision

Hardware set at detection of bus collision.

bit 9 GCSTAT: General Call Status bit

1 = General call address was received

0 = General call address was not received

Hardware set when address matches general call address. Hardware clear at Stop detection.

bit 8 ADD10: 10-Bit Address Status bit

1 = 10-bit address was matched

0 = 10-bit address was not matched

Hardware set at match of 2nd byte of matched 10-bit address. Hardware clear at Stop detection.

bit 7 IWCOL: Write Collision Detect bit

1 = An attempt to write the I2CxTRN register failed because the I2C module is busy

0 = No collision

Hardware set at occurrence of write to I2CxTRN while busy (cleared by software).

bit 6 I2COV: Receive Overflow Flag bit

1 = A byte was received while the I2CxRCV register is still holding the previous byte

0 = No overflow

Hardware set at attempt to transfer I2CxRSR to I2CxRCV (cleared by software).

bit 5 D_A: Data/Address bit (when operating as I2C slave)

1 = Indicates that the last byte received was data

0 = Indicates that the last byte received was device address

Hardware clear at device address match. Hardware set by reception of slave byte.

bit 4 P: Stop bit

1 = Indicates that a Stop bit has been detected last

0 = Stop bit was not detected last

Hardware set or clear when Start, Repeated Start or Stop detected.

dsPIC33FJXXXGPX06A/X08A/X10A

bit 3 S: Start bit

1 = Indicates that a Start (or Repeated Start) bit has been detected last

0 = Start bit was not detected last

Hardware set or clear when Start, Repeated Start or Stop detected.

bit 2 R_W: Read/Write Information bit (when operating as I2C slave)

1 = Read - indicates data transfer is output from slave

0 = Write - indicates data transfer is input to slave

Hardware set or clear after reception of I2C device address byte.

bit 1 RBF: Receive Buffer Full Status bit

1 = Receive complete, I2CxRCV is full

0 = Receive not complete, I2CxRCV is empty

Hardware set when I2CxRCV is written with received byte. Hardware clear when software

reads I2CxRCV.

bit 0 TBF: Transmit Buffer Full Status bit

1 = Transmit in progress, I2CxTRN is full

0 = Transmit complete, I2CxTRN is empty

Hardware set when software writes I2CxTRN. Hardware clear at completion of data transmission.

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0

— — — — — — AMSK9 AMSK8

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

AMSK7 AMSK6 AMSK5 AMSK4 AMSK3 AMSK2 AMSK1 AMSK0

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-10 Unimplemented: Read as ‘0’

bit 9-0 AMSKx: Mask for Address Bit x Select bit

1 = Enable masking for bit x of incoming message address; bit match not required in this position

0 = Disable masking for bit x; bit match required in this position

dsPIC33FJXXXGPX06A/X08A/X10A

NOTES:

dsPIC33FJXXXGPX06A/X08A/X10A

18.0 UNIVERSAL ASYNCHRONOUS

RECEIVER TRANSMITTER

(UART)

The Universal Asynchronous Receiver Transmitter

(UART) module is one of the serial I/O modules

available in the dsPIC33FJXXXGPX06A/X08A/X10A

device family. The UART is a full-duplex asynchronous

system that can communicate with peripheral devices,

such as personal computers, LIN, RS-232 and RS-485

interfaces. The module also supports a hardware flow

control option with the UxCTS and UxRTS pins and

also includes an IrDA® encoder and decoder.

The primary features of the UART module are:

• Full-Duplex, 8 or 9-bit Data Transmission through

the UxTX and UxRX pins

• Even, Odd or No Parity Options (for 8-bit data)

• One or Two Stop bits

• Hardware Flow Control Option with UxCTS and

UxRTS pins

• Fully Integrated Baud Rate Generator with 16-bit

Prescaler

• Baud rates ranging from 10 Mbps to 38 bps at 40

MIPS

• 4-deep First-In-First-Out (FIFO) Transmit Data

Buffer

• 4-Deep FIFO Receive Data Buffer

• Parity, Framing and Buffer Overrun Error Detection

• Support for 9-bit mode with Address Detect

(9th bit = 1)

• Transmit and Receive Interrupts

• A Separate Interrupt for all UART Error Conditions

• Loopback mode for Diagnostic Support

• Support for Sync and Break Characters

• Supports Automatic Baud Rate Detection

•IrDA

® Encoder and Decoder Logic

• 16x Baud Clock Output for IrDA® Support

A simplified block diagram of the UART is shown in

Figure 18-1. The UART module consists of the key

important hardware elements:

• Baud Rate Generator

• Asynchronous Transmitter

• Asynchronous Receiver

FIGURE 18-1: UART SIMPLIFIED BLOCK DIAGRAM

Note 1: This data sheet summarizes the fea-

tures of the dsPIC33FJXXXGPX06A/

X08A/X10A family of devices. How-

ever, it is not intended to be a compre-

hensive reference source. To

complement the information in this data

sheet, refer to Section 17. “UART”

(DS70188) in the “dsPIC33F/PIC24H

Family Reference Manual”, which is

available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Note 1: Both UART1 and UART2 can trigger a DMA data transfer. If U1TX, U1RX, U2TX or U2RX is selected as

a DMA IRQ source, a DMA transfer occurs when the U1TXIF, U1RXIF, U2TXIF or U2RXIF bit gets set as

a result of a UART1 or UART2 transmission or reception.

2: If DMA transfers are required, the UART TX/RX FIFO buffer must be set to a size of 1 byte/word (i.e.,

UTXISEL<1:0> = 00 and URXISEL<1:0> = 00).

UxRX

Hardware Flow Control

UART Receiver

UART Transmitter UxTX

/BCLK

Baud Rate Generator

UxRTS

IrDA®

UxCTS

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 U-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0

UARTEN(1) — USIDL IREN(2) RTSMD —UEN<1:0>

bit 15 bit 8

R/W-0 HC R/W-0 R/W-0 HC R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

WAKE LPBACK ABAUD URXINV BRGH PDSEL<1:0> STSEL

bit 7 bit 0

Legend: HC = Hardware cleared

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 UARTEN: UARTx Enable bit(1)

1 = UARTx is enabled; all UARTx pins are controlled by UARTx as defined by UEN<1:0>

0 = UARTx is disabled; all UARTx pins are controlled by port latches; UARTx power consumption

minimal

bit 14 Unimplemented: Read as ‘0’

bit 13 USIDL: Stop in Idle Mode bit

1 = Discontinue module operation when device enters Idle mode

0 = Continue module operation in Idle mode

bit 12 IREN: IrDA® Encoder and Decoder Enable bit(2)

1 =IrDA

® encoder and decoder enabled

0 =IrDA

® encoder and decoder disabled

bit 11 RTSMD: Mode Selection for UxRTS Pin bit

1 =UxRTS

pin in Simplex mode

0 =UxRTS pin in Flow Control mode

bit 10 Unimplemented: Read as ‘0’

bit 9-8 UEN<1:0>: UARTx Pin Enable bits

11 = UxTX, UxRX and BCLK pins are enabled and used; UxCTS pin controlled by port latches

10 = UxTX, UxRX, UxCTS and UxRTS pins are enabled and used

01 = UxTX, UxRX and UxRTS pins are enabled and used; UxCTS pin controlled by port latches

00 = UxTX and UxRX pins are enabled and used; UxCTS and UxRTS/BCLK pins controlled by

port latches

bit 7 WAKE: Wake-up on Start bit Detect During Sleep Mode Enable bit

1 = UARTx will continue to sample the UxRX pin; interrupt generated on falling edge; bit cleared

in hardware on following rising edge

0 = No wake-up enabled

bit 6 LPBACK: UARTx Loopback Mode Select bit

1 = Enable Loopback mode

0 = Loopback mode is disabled

bit 5 ABAUD: Auto-Baud Enable bit

1 = Enable baud rate measurement on the next character - requires reception of a Sync field (55h)

before other data; cleared in hardware upon completion

0 = Baud rate measurement disabled or completed

Note 1: Refer to Section 17. “UART” (DS70188) in the “dsPIC33F/PIC24H Family Reference Manual” for

information on enabling the UART module for receive or transmit operation.

2: This feature is only available for the 16x BRG mode (BRGH = 0).

dsPIC33FJXXXGPX06A/X08A/X10A

bit 4 URXINV: Receive Polarity Inversion bit

1 = UxRX Idle state is ‘0’

0 = UxRX Idle state is ‘1’

bit 3 BRGH: High Baud Rate Enable bit

1 = BRG generates 4 clocks per bit period (4x baud clock, High-Speed mode)

0 = BRG generates 16 clocks per bit period (16x baud clock, Standard mode)

bit 2-1 PDSEL<1:0>: Parity and Data Selection bits

11 = 9-bit data, no parity

10 = 8-bit data, odd parity

01 = 8-bit data, even parity

00 = 8-bit data, no parity

bit 0 STSEL: Stop Bit Selection bit

1 = Two Stop bits

0 = One Stop bit

Note 1: Refer to Section 17. “UART” (DS70188) in the “dsPIC33F/PIC24H Family Reference Manual” for

information on enabling the UART module for receive or transmit operation.

2: This feature is only available for the 16x BRG mode (BRGH = 0).

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 R/W-0 U-0 R/W-0 HC R/W-0 R-0 R-1

UTXISEL1 UTXINV UTXISEL0 — UTXBRK UTXEN(1) UTXBF TRMT

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R-1 R-0 R-0 R/C-0 R-0

URXISEL<1:0> ADDEN RIDLE PERR FERR OERR URXDA

bit 7 bit 0

Legend: HC = Hardware cleared C = Clear only bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15,13 UTXISEL<1:0>: Transmission Interrupt Mode Selection bits

11 = Reserved; do not use

10 = Interrupt when a character is transferred to the Transmit Shift Register, and as a result, the

transmit buffer becomes empty

01 = Interrupt when the last character is shifted out of the Transmit Shift Register; all transmit

operations are completed

00 = Interrupt when a character is transferred to the Transmit Shift Register (this implies there is

at least one character open in the transmit buffer)

bit 14 UTXINV: Transmit Polarity Inversion bit

If IREN = 0:

1 = UxTX Idle state is ‘0’

0 = UxTX Idle state is ‘1’

If IREN = 1:

1 =IrDA

® encoded UxTX Idle state is ‘1’

0 =IrDA

® encoded UxTX Idle state is ‘0’

bit 12 Unimplemented: Read as ‘0’

bit 11 UTXBRK: Transmit Break bit

1 = Send Sync Break on next transmission - Start bit, followed by twelve ‘0’ bits, followed by Stop bit;

cleared by hardware upon completion

0 = Sync Break transmission disabled or completed

bit 10 UTXEN: Transmit Enable bit(1)

1 = Transmit enabled, UxTX pin controlled by UARTx

0 = Transmit disabled, any pending transmission is aborted and buffer is reset. UxTX pin controlled

by port

bit 9 UTXBF: Transmit Buffer Full Status bit (read-only)

1 = Transmit buffer is full

0 = Transmit buffer is not full, at least one more character can be written

bit 8 TRMT: Transmit Shift Register Empty bit (read-only)

1 = Transmit Shift Register is empty and transmit buffer is empty (the last transmission has completed)

0 = Transmit Shift Register is not empty, a transmission is in progress or queued

bit 7-6 URXISEL<1:0>: Receive Interrupt Mode Selection bits

11 = Interrupt is set on UxRSR transfer making the receive buffer full (i.e., has 4 data characters)

10 = Interrupt is set on UxRSR transfer making the receive buffer 3/4 full (i.e., has 3 data characters)

0x = Interrupt is set when any character is received and transferred from the UxRSR to the receive

buffer. Receive buffer has one or more characters

Note 1: Refer to Section 17. “UART” (DS70188) in the “dsPIC33F/PIC24H Family Reference Manual” for

information on enabling the UART module for transmit operation.

dsPIC33FJXXXGPX06A/X08A/X10A

bit 5 ADDEN: Address Character Detect bit (bit 8 of received data = 1)

1 = Address Detect mode enabled. If 9-bit mode is not selected, this does not take effect

0 = Address Detect mode disabled

bit 4 RIDLE: Receiver Idle bit (read-only)

1 = Receiver is Idle

0 = Receiver is active

bit 3 PERR: Parity Error Status bit (read-only)

1 = Parity error has been detected for the current character (character at the top of the receive FIFO)

0 = Parity error has not been detected

bit 2 FERR: Framing Error Status bit (read-only)

1 = Framing error has been detected for the current character (character at the top of the receive

FIFO)

0 = Framing error has not been detected

bit 1 OERR: Receive Buffer Overrun Error Status bit (read/clear only)

1 = Receive buffer has overflowed

0 = Receive buffer has not overflowed. Clearing a previously set OERR bit (1→0 transition) will reset

the receiver buffer and the UxRSR to the empty state

bit 0 URXDA: Receive Buffer Data Available bit (read-only)

1 = Receive buffer has data, at least one more character can be read

0 = Receive buffer is empty

Note 1: Refer to Section 17. “UART” (DS70188) in the “dsPIC33F/PIC24H Family Reference Manual” for

information on enabling the UART module for transmit operation.

dsPIC33FJXXXGPX06A/X08A/X10A

NOTES:

dsPIC33FJXXXGPX06A/X08A/X10A

19.0 ENHANCED CAN (ECAN™)

MODULE

19.1 Overview

The Enhanced Controller Area Network (ECAN) mod-

ule is a serial interface, useful for communicating with

other CAN modules or microcontroller devices. This

interface/protocol was designed to allow communica-

tions within noisy environments. The

dsPIC33FJXXXGPX06A/X08A/X10A devices contain

up to two ECAN modules.

The CAN module is a communication controller imple-

menting the CAN 2.0 A/B protocol, as defined in the

BOSCH specification. The module will support CAN 1.2,

CAN 2.0A, CAN 2.0B Passive and CAN 2.0B Active

versions of the protocol. The module implementation is

a full CAN system. The CAN specification is not covered

within this data sheet. The reader may refer to the

BOSCH CAN specification for further details.

The module features are as follows:

• Implementation of the CAN protocol, CAN 1.2,

CAN 2.0A and CAN 2.0B

• Standard and extended data frames

• 0-8 bytes data length

• Programmable bit rate up to 1 Mbit/sec

• Automatic response to remote transmission

requests

• Up to eight transmit buffers with application speci-

fied prioritization and abort capability (each buffer

may contain up to 8 bytes of data)

• Up to 32 receive buffers (each buffer may contain

up to 8 bytes of data)

• Up to 16 full (standard/extended identifier)

acceptance filters

• Three full acceptance filter masks

• DeviceNet™ addressing support

• Programmable wake-up functionality with

integrated low-pass filter

• Programmable Loopback mode supports self-test

operation

• Signaling via interrupt capabilities for all CAN

receiver and transmitter error states

• Programmable clock source

• Programmable link to input capture module (IC2

for both CAN1 and CAN2) for time-stamping and

network synchronization

• Low-power Sleep and Idle mode

The CAN bus module consists of a protocol engine and

message buffering/control. The CAN protocol engine

handles all functions for receiving and transmitting

messages on the CAN bus. Messages are transmitted

by first loading the appropriate data registers. Status

and errors can be checked by reading the appropriate

registers. Any message detected on the CAN bus is

checked for errors and then matched against filters to

see if it should be received and stored in one of the

receive registers.

19.2 Frame Types

The CAN module transmits various types of frames

which include data messages, or remote transmission

requests initiated by the user, as other frames that are

automatically generated for control purposes. The

following frame types are supported:

• Standard Data Frame:

A standard data frame is generated by a node when

the node wishes to transmit data. It includes an

11-bit Standard Identifier (SID), but not an 18-bit

Extended Identifier (EID).

• Extended Data Frame:

An extended data frame is similar to a standard data

frame, but also includes an extended identifier.

• Remote Frame:

It is possible for a destination node to request the

data from the source. For this purpose, the

destination node sends a remote frame with an iden-

tifier that matches the identifier of the required data

frame. The appropriate data source node will then

send a data frame as a response to this remote

request.

• Error Frame:

An error frame is generated by any node that detects

a bus error. An error frame consists of two fields: an

error flag field and an error delimiter field.

• Overload Frame:

An overload frame can be generated by a node as a

result of two conditions. First, the node detects a

dominant bit during interframe space which is an ille-

gal condition. Second, due to internal conditions, the

node is not yet able to start reception of the next

message. A node may generate a maximum of two

sequential overload frames to delay the start of the

next message.

• Interframe Space:

Interframe space separates a proceeding frame (of

whatever type) from a following data or remote

frame.

Note 1: This data sheet summarizes the fea-

tures of the dsPIC33FJXXXGPX06A/

X08A/X10A family of devices. How-

ever, it is not intended to be a compre-

hensive reference source. To

complement the information in this data

sheet, refer to Section 21. “Enhanced

Controller Area Network (ECAN™)”

(DS70185) in the “dsPIC33F/PIC24H

Family Reference Manual”, which is

available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 19-1: ECAN™ MODULE BLOCK DIAGRAM

Message Assembly

CAN Protocol

Engine

CiTX(1)

Buffer

CiRX(1)

RXF14 Filter

RXF13 Filter

RXF12 Filter

RXF11 Filter

RXF10 Filter

RXF9 Filter

RXF8 Filter

RXF7 Filter

RXF6 Filter

RXF5 Filter

RXF4 Filter

RXF3 Filter

RXF2 Filter

RXF1 Filter

RXF0 Filter

Transmit Byte

Sequencer

RXM1 Mask

RXM0 Mask

Control

Configuration

Logic

CPU

Bus

Interrupts

TRB0 TX/RX Buffer Control Register

DMA Controller

RXF15 Filter

RXM2 Mask

TRB7 TX/RX Buffer Control Register

TRB6 TX/RX Buffer Control Register

TRB5 TX/RX Buffer Control Register

TRB4 TX/RX Buffer Control Register

TRB3 TX/RX Buffer Control Register

TRB2 TX/RX Buffer Control Register

TRB1 TX/RX Buffer Control Register

Note 1: i = 1 or 2 refers to a particular ECAN™ module (ECAN1 or ECAN2).

dsPIC33FJXXXGPX06A/X08A/X10A

19.3 Modes of Operation

The CAN module can operate in one of several operation

modes selected by the user. These modes include:

• Initialization Mode

• Disable Mode

• Normal Operation Mode

• Listen Only Mode

• Listen All Messages Mode

• Loopback Mode

Modes are requested by setting the REQOP<2:0> bits

(CiCTRL1<10:8>). Entry into a mode is Acknowledged

by monitoring the OPMODE<2:0> bits

(CiCTRL1<7:5>). The module will not change the mode

and the OPMODE bits until a change in mode is

acceptable, generally during bus Idle time, which is

defined as at least 11 consecutive recessive bits.

19.3.1 INITIALIZATION MODE

In the Initialization mode, the module will not transmit or

receive. The error counters are cleared and the

interrupt flags remain unchanged. The programmer will

have access to Configuration registers that are access

restricted in other modes. The module will protect the

user from accidentally violating the CAN protocol

through programming errors. All registers which control

the configuration of the module can not be modified

while the module is on-line. The CAN module will not

be allowed to enter the Configuration mode while a

transmission is taking place. The Configuration mode

serves as a lock to protect the following registers:

• All Module Control Registers

• Baud Rate and Interrupt Configuration Registers

• Bus Timing Registers

• Identifier Acceptance Filter Registers

• Identifier Acceptance Mask Registers

19.3.2 DISABLE MODE

In Disable mode, the module will not transmit or

receive. The module has the ability to set the WAKIF bit

due to bus activity, however, any pending interrupts will

remain and the error counters will retain their value.

If the REQOP<2:0> bits (CiCTRL1<10:8>) = 001, the

module will enter the Module Disable mode. If the module

is active, the module will wait for 11 recessive bits on the

CAN bus, detect that condition as an Idle bus, then

accept the module disable command. When the

OPMODE<2:0> bits (CiCTRL1<7:5>) = 001, that

indicates whether the module successfully went into

Module Disable mode. The I/O pins will revert to normal

I/O function when the module is in the Module Disable

mode.

The module can be programmed to apply a low-pass

filter function to the CiRX input line while the module or

the CPU is in Sleep mode. The WAKFIL bit

(CiCFG2<14>) enables or disables the filter.

19.3.3 NORMAL OPERATION MODE

Normal Operation mode is selected when

REQOP<2:0> = 000. In this mode, the module is

activated and the I/O pins will assume the CAN bus

functions. The module will transmit and receive CAN

bus messages via the CiTX and CiRX pins.

19.3.4 LISTEN ONLY MODE

If the Listen Only mode is activated, the module on the

CAN bus is passive. The transmitter buffers revert to

the port I/O function. The receive pins remain inputs.

For the receiver, no error flags or Acknowledge signals

are sent. The error counters are deactivated in this

state. The Listen Only mode can be used for detecting

the baud rate on the CAN bus. To use this, it is

necessary that there are at least two further nodes that

communicate with each other.

19.3.5 LISTEN ALL MESSAGES MODE

The module can be set to ignore all errors and receive

any message. The Listen All Messages mode is

activated by setting REQOP<2:0> = ‘111’. In this

mode, the data which is in the message assembly buf-

fer, until the time an error occurred, is copied in the

receive buffer and can be read via the CPU interface.

19.3.6 LOOPBACK MODE

If the Loopback mode is activated, the module will

connect the internal transmit signal to the internal

receive signal at the module boundary. The transmit

and receive pins revert to their port I/O function.

Note: Typically, if the CAN module is allowed to

transmit in a particular mode of operation

and a transmission is requested

immediately after the CAN module has

been placed in that mode of operation, the

module waits for 11 consecutive recessive

bits on the bus before starting

transmission. If the user switches to

Disable mode within this 11-bit period,

then this transmission is aborted and the

corresponding TXABT bit is set and

TXREQ bit is cleared.

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 R/W-0 R/W-0 r-0 R/W-1 R/W-0 R/W-0

—— CSIDL ABAT — REQOP<2:0>

bit 15 bit 8

R-1 R-0 R-0 U-0 R/W-0 U-0 U-0 R/W-0

OPMODE<2:0> —CANCAP ——WIN

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared r = Bit is Reserved

bit 15-14 Unimplemented: Read as ‘0’

bit 13 CSIDL: Stop in Idle Mode bit

1 = Discontinue module operation when device enters Idle mode

0 = Continue module operation in Idle mode

bit 12 ABAT: Abort All Pending Transmissions bit

1 = Signal all transmit buffers to abort transmission

0 = Module will clear this bit when all transmissions are aborted

bit 11 Reserved: Do not use

bit 10-8 REQOP<2:0>: Request Operation Mode bits

111 = Set Listen All Messages mode

110 = Reserved - do not use

101 = Reserved - do not use

100 = Set Configuration mode

011 = Set Listen Only Mode

010 = Set Loopback mode

001 = Set Disable mode

000 = Set Normal Operation mode

bit 7-5 OPMODE<2:0>: Operation Mode bits

111 = Module is in Listen All Messages mode

110 = Reserved

101 = Reserved

100 = Module is in Configuration mode

011 = Module is in Listen Only mode

010 = Module is in Loopback mode

001 = Module is in Disable mode

000 = Module is in Normal Operation mode

bit 4 Unimplemented: Read as ‘0’

bit 3 CANCAP: CAN Message Receive Timer Capture Event Enable bit

1 = Enable input capture based on CAN message receive

0 = Disable CAN capture

bit 2-1 Unimplemented: Read as ‘0’

bit 0 WIN: SFR Map Window Select bit

1 = Use filter window

0 = Use buffer window

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 U-0 U-0 R-0 R-0 R-0 R-0 R-0

— — — DNCNT<4:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-5 Unimplemented: Read as ‘0’

bit 4-0 DNCNT<4:0>: DeviceNet™ Filter Bit Number bits

11111 = Invalid selection

•

10010 = Invalid selection

10001 = Compare up to data byte 3, bit 6 with EID<17>

•

00001 = Compare up to data byte 1, bit 7 with EID<0>

00000 = Do not compare data bytes

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 R-0 R-0 R-0 R-0 R-0

— — — FILHIT<4:0>

bit 15 bit 8

U-0 R-1 R-0 R-0 R-0 R-0 R-0 R-0

—ICODE<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-13 Unimplemented: Read as ‘0’

bit 12-8 FILHIT<4:0>: Filter Hit Number bits

10000-11111 = Reserved

01111 = Filter 15

•

00001 = Filter 1

00000 = Filter 0

bit 7 Unimplemented: Read as ‘0’

bit 6-0 ICODE<6:0>: Interrupt Flag Code bits

1000101-1111111 = Reserved

1000100 = FIFO almost full interrupt

1000011 = Receiver overflow interrupt

1000010 = Wake-up interrupt

1000001 = Error interrupt

1000000 = No interrupt

0010000-0111111 = Reserved

0001111 = RB15 buffer Interrupt

•

0001001 = RB9 buffer interrupt

0001000 = RB8 buffer interrupt

0000111 = TRB7 buffer interrupt

0000110 = TRB6 buffer interrupt

0000101 = TRB5 buffer interrupt

0000100 = TRB4 buffer interrupt

0000011 = TRB3 buffer interrupt

0000010 = TRB2 buffer interrupt

0000001 = TRB1 buffer interrupt

0000000 = TRB0 Buffer interrupt

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 U-0 U-0

DMABS<2:0> — — — — —

bit 15 bit 8

U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— — — FSA<4:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-13 DMABS<2:0>: DMA Buffer Size bits

111 = Reserved; do not use

110 = 32 buffers in DMA RAM

101 = 24 buffers in DMA RAM

100 = 16 buffers in DMA RAM

011 = 12 buffers in DMA RAM

010 = 8 buffers in DMA RAM

001 = 6 buffers in DMA RAM

000 = 4 buffers in DMA RAM

bit 12-5 Unimplemented: Read as ‘0’

bit 4-0 FSA<4:0>: FIFO Area Starts with Buffer bits

11111 = RB31 buffer

11110 = RB30 buffer

•

00001 = TRB1 buffer

00000 = TRB0 buffer

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 R-0 R-0 R-0 R-0 R-0 R-0

—— FBP<5:0>

bit 15 bit 8

U-0 U-0 R-0 R-0 R-0 R-0 R-0 R-0

—— FNRB<5:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13-8 FBP<5:0>: FIFO Write Buffer Pointer bits

011111 = RB31 buffer

011110 = RB30 buffer

•

000001 = TRB1 buffer

000000 = TRB0 buffer

bit 7-6 Unimplemented: Read as ‘0’

bit 5-0 FNRB<5:0>: FIFO Next Read Buffer Pointer bits

011111 = RB31 buffer

011110 = RB30 buffer

•

000001 = TRB1 buffer

000000 = TRB0 buffer

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 R-0 R-0 R-0 R-0 R-0 R-0

—— TXBO TXBP RXBP TXWAR RXWAR EWARN

bit 15 bit 8

R/C-0 R/C-0 R/C-0 U-0 R/C-0 R/C-0 R/C-0 R/C-0

IVRIF WAKIF ERRIF — FIFOIF RBOVIF RBIF TBIF

bit 7 bit 0

Legend: C = Clear only bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13 TXBO: Transmitter in Error State Bus Off bit

1 = Transmitter is in Bus Off state

0 = Transmitter is not in Bus Off state

bit 12 TXBP: Transmitter in Error State Bus Passive bit

1 = Transmitter is in Bus Passive state

0 = Transmitter is not in Bus Passive state

bit 11 RXBP: Receiver in Error State Bus Passive bit

1 = Receiver is in Bus Passive state

0 = Receiver is not in Bus Passive state

bit 10 TXWAR: Transmitter in Error State Warning bit

1 = Transmitter is in Error Warning state

0 = Transmitter is not in Error Warning state

bit 9 RXWAR: Receiver in Error State Warning bit

1 = Receiver is in Error Warning state

0 = Receiver is not in Error Warning state

bit 8 EWARN: Transmitter or Receiver in Error State Warning bit

1 = Transmitter or receiver is in Error Warning state

0 = Transmitter or receiver is not in Error Warning state

bit 7 IVRIF: Invalid Message Received Interrupt Flag bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 6 WAKIF: Bus Wake-up Activity Interrupt Flag bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 5 ERRIF: Error Interrupt Flag bit (multiple sources in CiINTF<13:8> register)

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 4 Unimplemented: Read as ‘0’

bit 3 FIFOIF: FIFO Almost Full Interrupt Flag bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 2 RBOVIF: RX Buffer Overflow Interrupt Flag bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 1 RBIF: RX Buffer Interrupt Flag bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

bit 0 TBIF: TX Buffer Interrupt Flag bit

1 = Interrupt request has occurred

0 = Interrupt request has not occurred

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0

IVRIE WAKIE ERRIE — FIFOIE RBOVIE RBIE TBIE

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7 IVRIE: Invalid Message Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 6 WAKIE: Bus Wake-up Activity Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 5 ERRIE: Error Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 4 Unimplemented: Read as ‘0’

bit 3 FIFOIE: FIFO Almost Full Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 2 RBOVIE: RX Buffer Overflow Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 1 RBIE: RX Buffer Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

bit 0 TBIE: TX Buffer Interrupt Enable bit

1 = Interrupt request enabled

0 = Interrupt request not enabled

dsPIC33FJXXXGPX06A/X08A/X10A

R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

TERRCNT<7:0>

bit 15 bit 8

R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

RERRCNT<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 TERRCNT<7:0>: Transmit Error Count bits

bit 7-0 RERRCNT<7:0>: Receive Error Count bits

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SJW<1:0> BRP<5:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7-6 SJW<1:0>: Synchronization Jump Width bits

11 = Length is 4 x TQ

10 = Length is 3 x TQ

01 = Length is 2 x TQ

00 = Length is 1 x TQ

bit 5-0 BRP<5:0>: Baud Rate Prescaler bits

11 1111 = TQ = 2 x 64 x 1/FCAN

•

00 0010 = TQ = 2 x 3 x 1/FCAN

00 0001 = TQ = 2 x 2 x 1/FCAN

00 0000 = TQ = 2 x 1 x 1/FCAN

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 R/W-x U-0 U-0 U-0 R/W-x R/W-x R/W-x

— WAKFIL — — — SEG2PH<2:0>

bit 15 bit 8

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

SEG2PHTS SAM SEG1PH<2:0> PRSEG<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14 WAKFIL: Select CAN bus Line Filter for Wake-up bit

1 = Use CAN bus line filter for wake-up

0 = CAN bus line filter is not used for wake-up

bit 13-11 Unimplemented: Read as ‘0’

bit 10-8 SEG2PH<2:0>: Phase Buffer Segment 2 bits

111 = Length is 8 x TQ

000 = Length is 1 x TQ

bit 7 SEG2PHTS: Phase Segment 2 Time Select bit

1 = Freely programmable

0 = Maximum of SEG1PH bits or Information Processing Time (IPT), whichever is greater

bit 6 SAM: Sample of the CAN bus Line bit

1 = Bus line is sampled three times at the sample point

0 = Bus line is sampled once at the sample point

bit 5-3 SEG1PH<2:0>: Phase Buffer Segment 1 bits

111 = Length is 8 x TQ

000 = Length is 1 x TQ

bit 2-0 PRSEG<2:0>: Propagation Time Segment bits

111 = Length is 8 x TQ

000 = Length is 1 x TQ

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1

FLTEN15 FLTEN14 FLTEN13 FLTEN12 FLTEN11 FLTEN10 FLTEN9 FLTEN8

bit 15 bit 8

R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1

FLTEN7 FLTEN6 FLTEN5 FLTEN4 FLTEN3 FLTEN2 FLTEN1 FLTEN0

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 FLTENn: Enable Filter n to Accept Messages bits

1 = Enable Filter n

0 = Disable Filter n

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F3BP<3:0> F2BP<3:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F1BP<3:0> F0BP<3:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 F3BP<3:0>: RX Buffer Written when Filter 3 Hits bits

1111 = Filter hits received in RX FIFO buffer

1110 = Filter hits received in RX Buffer 14

•

0001 = Filter hits received in RX Buffer 1

0000 = Filter hits received in RX Buffer 0

bit 11-8 F2BP<3:0>: RX Buffer Written when Filter 2 Hits bits

1111 = Filter hits received in RX FIFO buffer

1110 = Filter hits received in RX Buffer 14

•

0001 = Filter hits received in RX Buffer 1

0000 = Filter hits received in RX Buffer 0

bit 7-4 F1BP<3:0>: RX Buffer Written when Filter 1 Hits bits

1111 = Filter hits received in RX FIFO buffer

1110 = Filter hits received in RX Buffer 14

•

0001 = Filter hits received in RX Buffer 1

0000 = Filter hits received in RX Buffer 0

bit 3-0 F0BP<3:0>: RX Buffer Written when Filter 0 Hits bits

1111 = Filter hits received in RX FIFO buffer

1110 = Filter hits received in RX Buffer 14

•

0001 = Filter hits received in RX Buffer 1

0000 = Filter hits received in RX Buffer 0

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F7BP<3:0> F6BP<3:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F5BP<3:0> F4BP<3:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 F7BP<3:0>: RX Buffer Written when Filter 7 Hits bits

1111 = Filter hits received in RX FIFO buffer

1110 = Filter hits received in RX Buffer 14

•

0001 = Filter hits received in RX Buffer 1

0000 = Filter hits received in RX Buffer 0

bit 11-8 F6BP<3:0>: RX Buffer Written when Filter 6 Hits bits

1111 = Filter hits received in RX FIFO buffer

1110 = Filter hits received in RX Buffer 14

•

0001 = Filter hits received in RX Buffer 1

0000 = Filter hits received in RX Buffer 0

bit 7-4 F5BP<3:0>: RX Buffer Written when Filter 5 Hits bits

1111 = Filter hits received in RX FIFO buffer

1110 = Filter hits received in RX Buffer 14

•

0001 = Filter hits received in RX Buffer 1

0000 = Filter hits received in RX Buffer 0

bit 3-0 F4BP<3:0>: RX Buffer Written when Filter 4 Hits bits

1111 = Filter hits received in RX FIFO buffer

1110 = Filter hits received in RX Buffer 14

•

0001 = Filter hits received in RX Buffer 1

0000 = Filter hits received in RX Buffer 0

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F11BP<3:0> F10BP<3:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F9BP<3:0> F8BP<3:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 F11BP<3:0>: RX Buffer Written when Filter 11 Hits bits

1111 = Filter hits received in RX FIFO buffer

1110 = Filter hits received in RX Buffer 14

•

0001 = Filter hits received in RX Buffer 1

0000 = Filter hits received in RX Buffer 0

bit 11-8 F10BP<3:0>: RX Buffer Written when Filter 10 Hits bits

1111 = Filter hits received in RX FIFO buffer

1110 = Filter hits received in RX Buffer 14

•

0001 = Filter hits received in RX Buffer 1

0000 = Filter hits received in RX Buffer 0

bit 7-4 F9BP<3:0>: RX Buffer Written when Filter 9 Hits bits

1111 = Filter hits received in RX FIFO buffer

1110 = Filter hits received in RX Buffer 14

•

0001 = Filter hits received in RX Buffer 1

0000 = Filter hits received in RX Buffer 0

bit 3-0 F8BP<3:0>: RX Buffer Written when Filter 8 Hits bits

1111 = Filter hits received in RX FIFO buffer

1110 = Filter hits received in RX Buffer 14

•

0001 = Filter hits received in RX Buffer 1

0000 = Filter hits received in RX Buffer 0

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F15BP<3:0> F14BP<3:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F13BP<3:0> F12BP<3:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 F15BP<3:0>: RX Buffer Written when Filter 15 Hits bits

1111 = Filter hits received in RX FIFO buffer

1110 = Filter hits received in RX Buffer 14

•

0001 = Filter hits received in RX Buffer 1

0000 = Filter hits received in RX Buffer 0

bit 11-8 F14BP<3:0>: RX Buffer Written when Filter 14 Hits bits

1111 = Filter hits received in RX FIFO buffer

1110 = Filter hits received in RX Buffer 14

•

0001 = Filter hits received in RX Buffer 1

0000 = Filter hits received in RX Buffer 0

bit 7-4 F13BP<3:0>: RX Buffer Written when Filter 13 Hits bits

1111 = Filter hits received in RX FIFO buffer

1110 = Filter hits received in RX Buffer 14

•

0001 = Filter hits received in RX Buffer 1

0000 = Filter hits received in RX Buffer 0

bit 3-0 F12BP<3:0>: RX Buffer Written when Filter 12 Hits bits

1111 = Filter hits received in RX FIFO buffer

1110 = Filter hits received in RX Buffer 14

•

0001 = Filter hits received in RX Buffer 1

0000 = Filter hits received in RX Buffer 0

dsPIC33FJXXXGPX06A/X08A/X10A

™

ACCEPTANCE FILTER n STANDARD IDENTIFIER (n = 0, 1, ..., 15)

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

SID<10:3>

bit 15 bit 8

R/W-x R/W-x R/W-x U-0 R/W-x U-0 R/W-x R/W-x

SID<2:0> —EXIDE —EID<17:16>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-5 SID<10:0>: Standard Identifier bits

1 = Message address bit SIDx must be ‘1’ to match filter

0 = Message address bit SIDx must be ‘0’ to match filter

bit 4 Unimplemented: Read as ‘0’

bit 3 EXIDE: Extended Identifier Enable bit

If MIDE = 1 then:

1 = Match only messages with extended identifier addresses

0 = Match only messages with standard identifier addresses

If MIDE = 0 then:

Ignore EXIDE bit.

bit 2 Unimplemented: Read as ‘0’

bit 1-0 EID<17:16>: Extended Identifier bits

1 = Message address bit EIDx must be ‘1’ to match filter

0 = Message address bit EIDx must be ‘0’ to match filter

™

ACCEPTANCE FILTER n EXTENDED IDENTIFIER (n = 0, 1, ..., 15)

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

EID<15:8>

bit 15 bit 8

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

EID<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 EID<15:0>: Extended Identifier bits

1 = Message address bit EIDx must be ‘1’ to match filter

0 = Message address bit EIDx must be ‘0’ to match filter

dsPIC33FJXXXGPX06A/X08A/X10A

ECAN

™

FILTER 7-0 MASK SELECTION REGISTER

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F7MSK<1:0> F6MSK<1:0> F5MSK<1:0> F4MSK<1:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F3MSK<1:0> F2MSK<1:0> F1MSK<1:0> F0MSK<1:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 F7MSK<1:0>: Mask Source for Filter 7 bit

11 = Reserved; do not use

10 = Acceptance Mask 2 registers contain mask

01 = Acceptance Mask 1 registers contain mask

00 = Acceptance Mask 0 registers contain mask

bit 13-12 F6MSK<1:0>: Mask Source for Filter 6 bit

11 = Reserved; do not use

10 = Acceptance Mask 2 registers contain mask

01 = Acceptance Mask 1 registers contain mask

00 = Acceptance Mask 0 registers contain mask

bit 11-10 F5MSK<1:0>: Mask Source for Filter 5 bit

11 = Reserved; do not use

10 = Acceptance Mask 2 registers contain mask

01 = Acceptance Mask 1 registers contain mask

00 = Acceptance Mask 0 registers contain mask

bit 9-8 F4MSK<1:0>: Mask Source for Filter 4 bit

11 = Reserved; do not use

10 = Acceptance Mask 2 registers contain mask

01 = Acceptance Mask 1 registers contain mask

00 = Acceptance Mask 0 registers contain mask

bit 7-6 F3MSK<1:0>: Mask Source for Filter 3 bit

11 = Reserved; do not use

10 = Acceptance Mask 2 registers contain mask

01 = Acceptance Mask 1 registers contain mask

00 = Acceptance Mask 0 registers contain mask

bit 5-4 F2MSK<1:0>: Mask Source for Filter 2 bit

11 = Reserved; do not use

10 = Acceptance Mask 2 registers contain mask

01 = Acceptance Mask 1 registers contain mask

00 = Acceptance Mask 0 registers contain mask

bit 3-2 F1MSK<1:0>: Mask Source for Filter 1 bit

11 = Reserved; do not use

10 = Acceptance Mask 2 registers contain mask

01 = Acceptance Mask 1 registers contain mask

00 = Acceptance Mask 0 registers contain mask

bit 1-0 F0MSK<1:0>: Mask Source for Filter 0 bit

11 = Reserved; do not use

10 = Acceptance Mask 2 registers contain mask

01 = Acceptance Mask 1 registers contain mask

00 = Acceptance Mask 0 registers contain mask

dsPIC33FJXXXGPX06A/X08A/X10A

ECAN™

FILTER 15-8 MASK SELECTION REGISTER

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F15MSK<1:0> F14MSK<1:0> F13MSK<1:0> F12MSK<1:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F11MSK<1:0> F10MSK<1:0> F9MSK<1:0> F8MSK<1:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 F15MSK<1:0>: Mask Source for Filter 15 bit

11 = Reserved; do not use

10 = Acceptance Mask 2 registers contain mask

01 = Acceptance Mask 1 registers contain mask

00 = Acceptance Mask 0 registers contain mask

bit 13-12 F14MSK<1:0>: Mask Source for Filter 14 bit

11 = Reserved; do not use

10 = Acceptance Mask 2 registers contain mask

01 = Acceptance Mask 1 registers contain mask

00 = Acceptance Mask 0 registers contain mask

bit 11-10 F13MSK<1:0>: Mask Source for Filter 13 bit

11 = Reserved; do not use

10 = Acceptance Mask 2 registers contain mask

01 = Acceptance Mask 1 registers contain mask

00 = Acceptance Mask 0 registers contain mask

bit 9-8 F12MSK<1:0>: Mask Source for Filter 12 bit

11 = Reserved; do not use

10 = Acceptance Mask 2 registers contain mask

01 = Acceptance Mask 1 registers contain mask

00 = Acceptance Mask 0 registers contain mask

bit 7-6 F11MSK<1:0>: Mask Source for Filter 11 bit

11 = Reserved; do not use

10 = Acceptance Mask 2 registers contain mask

01 = Acceptance Mask 1 registers contain mask

00 = Acceptance Mask 0 registers contain mask

bit 5-4 F10MSK<1:0>: Mask Source for Filter 10 bit

11 = Reserved; do not use

10 = Acceptance Mask 2 registers contain mask

01 = Acceptance Mask 1 registers contain mask

00 = Acceptance Mask 0 registers contain mask

bit 3-2 F9MSK<1:0>: Mask Source for Filter 9 bit

11 = Reserved; do not use

10 = Acceptance Mask 2 registers contain mask

01 = Acceptance Mask 1 registers contain mask

00 = Acceptance Mask 0 registers contain mask

bit 1-0 F8MSK<1:0>: Mask Source for Filter 8 bit

11 = Reserved; do not use

10 = Acceptance Mask 2 registers contain mask

01 = Acceptance Mask 1 registers contain mask

00 = Acceptance Mask 0 registers contain mask

dsPIC33FJXXXGPX06A/X08A/X10A

ECAN

™

ACCEPTANCE FILTER MASK n STANDARD IDENTIFIER

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

SID<10:3>

bit 15 bit 8

R/W-x R/W-x R/W-x U-0 R/W-x U-0 R/W-x R/W-x

SID<2:0> —MIDE —EID<17:16>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-5 SID<10:0>: Standard Identifier bits

1 = Include bit SIDx in filter comparison

0 = Bit SIDx is don’t care in filter comparison

bit 4 Unimplemented: Read as ‘0’

bit 3 MIDE: Identifier Receive Mode bit

1 = Match only message types (standard or extended address) that correspond to EXIDE bit in filter

0 = Match either standard or extended address message if filters match

(i.e., if (Filter SID) = (Message SID) or if (Filter SID/EID) = (Message SID/EID))

bit 2 Unimplemented: Read as ‘0’

bit 1-0 EID<17:16>: Extended Identifier bits

1 = Include bit EIDx in filter comparison

0 = Bit EIDx is don’t care in filter comparison

ECAN

™

ACCEPTANCE FILTER MASK n EXTENDED IDENTIFIER

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

EID<15:8>

bit 15 bit 8

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

EID<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 EID<15:0>: Extended Identifier bits

1 = Include bit EIDx in filter comparison

0 = Bit EIDx is don’t care in filter comparison

dsPIC33FJXXXGPX06A/X08A/X10A

R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0

RXFUL15 RXFUL14 RXFUL13 RXFUL12 RXFUL11 RXFUL10 RXFUL9 RXFUL8

bit 15 bit 8

R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0

RXFUL7 RXFUL6 RXFUL5 RXFUL4 RXFUL3 RXFUL2 RXFUL1 RXFUL0

bit 7 bit 0

Legend: C = Clear only bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 RXFUL15:RXFUL0: Receive Buffer n Full bits

1 = Buffer is full (set by module)

0 = Buffer is empty (clear by application software)

R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0

RXFUL31 RXFUL30 RXFUL29 RXFUL28 RXFUL27 RXFUL26 RXFUL25 RXFUL24

bit 15 bit 8

R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0

RXFUL23 RXFUL22 RXFUL21 RXFUL20 RXFUL19 RXFUL18 RXFUL17 RXFUL16

bit 7 bit 0

Legend: C = Clear only bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 RXFUL31:RXFUL16: Receive Buffer n Full bits

1 = Buffer is full (set by module)

0 = Buffer is empty (clear by application software)

dsPIC33FJXXXGPX06A/X08A/X10A

R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0

RXOVF15 RXOVF14 RXOVF13 RXOVF12 RXOVF11 RXOVF10 RXOVF9 RXOVF8

bit 15 bit 8

R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0

RXOVF7 RXOVF6 RXOVF5 RXOVF4 RXOVF3 RXOVF2 RXOVF1 RXOVF0

bit 7 bit 0

Legend: C = Clear only bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 RXOVF15:RXOVF0: Receive Buffer n Overflow bits

1 = Module pointed a write to a full buffer (set by module)

0 = Overflow is cleared (clear by application software)

R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0

RXOVF31 RXOVF30 RXOVF29 RXOVF28 RXOVF27 RXOVF26 RXOVF25 RXOVF24

bit 15 bit 8

R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0

RXOVF23 RXOVF22 RXOVF21 RXOVF20 RXOVF19 RXOVF18 RXOVF17 RXOVF16

bit 7 bit 0

Legend: C = Clear only bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 RXOVF31:RXOVF16: Receive Buffer n Overflow bits

1 = Module pointed a write to a full buffer (set by module)

0 = Overflow is cleared (clear by application software)

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R-0 R-0 R-0 R/W-0 R/W-0 R/W-0 R/W-0

TXENn TXABTn TXLARBn TXERRn TXREQn RTRENn TXnPRI<1:0>

bit 15 bit 8

R/W-0 R-0 R-0 R-0 R/W-0 R/W-0 R/W-0 R/W-0

TXENm TXABTm(1) TXLARBm(1) TXERRm(1) TXREQm RTRENm TXmPRI<1:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 See Definition for Bits 7-0, Controls Buffer n

bit 7 TXENm: TX/RX Buffer Selection bit

1 = Buffer TRBn is a transmit buffer

0 = Buffer TRBn is a receive buffer

bit 6 TXABTm: Message Aborted bit(1)

1 = Message was aborted

0 = Message completed transmission successfully

bit 5 TXLARBm: Message Lost Arbitration bit(1)

1 = Message lost arbitration while being sent

0 = Message did not lose arbitration while being sent

bit 4 TXERRm: Error Detected During Transmission bit(1)

1 = A bus error occurred while the message was being sent

0 = A bus error did not occur while the message was being sent

bit 3 TXREQm: Message Send Request bit

Setting this bit to ‘1’ requests sending a message. The bit will automatically clear when the message

is successfully sent. Clearing the bit to ‘0’ while set will request a message abort.

bit 2 RTRENm: Auto-Remote Transmit Enable bit

1 = When a remote transmit is received, TXREQ will be set

0 = When a remote transmit is received, TXREQ will be unaffected

bit 1-0 TXmPRI<1:0>: Message Transmission Priority bits

11 = Highest message priority

10 = High intermediate message priority

01 = Low intermediate message priority

00 = Lowest message priority

Note 1: This bit is cleared when TXREQ is set.

dsPIC33FJXXXGPX06A/X08A/X10A

Note: The buffers, SID, EID, DLC, Data Field and Receive Status registers are located in DMA RAM.

ECAN™

BUFFER n STANDARD IDENTIFIER (n = 0, 1, ..., 31)

U-0 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x

— — — SID<10:6>

bit 15 bit 8

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

SID<5:0> SRR IDE

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-13 Unimplemented: Read as ‘0’

bit 12-2 SID<10:0>: Standard Identifier bits

bit 1 SRR: Substitute Remote Request bit

1 = Message will request remote transmission

0 = Normal message

bit 0 IDE: Extended Identifier bit

1 = Message will transmit extended identifier

0 = Message will transmit standard identifier

ECAN™

BUFFER n EXTENDED IDENTIFIER (n = 0, 1, ..., 31)

U-0 U-0 U-0 U-0 R/W-x R/W-x R/W-x R/W-x

— — — — EID<17:14>

bit 15 bit 8

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

EID<13:6>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 Unimplemented: Read as ‘0’

bit 11-0 EID<17:6>: Extended Identifier bits

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

EID<5:0> RTR RB1

bit 15 bit 8

U-0 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x

— — — RB0 DLC<3:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-10 EID<5:0>: Extended Identifier bits

bit 9 RTR: Remote Transmission Request bit

1 = Message will request remote transmission

0 = Normal message

bit 8 RB1: Reserved Bit 1

User must set this bit to ‘0’ per CAN protocol.

bit 7-5 Unimplemented: Read as ‘0’

bit 4 RB0: Reserved Bit 0

User must set this bit to ‘0’ per CAN protocol.

bit 3-0 DLC<3:0>: Data Length Code bits

(n = 0, 1, ..., 31; m = 0, 1, ..., 7)

(1)

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

TRBnDm<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 7-0 TRBnDm<7:0>: Data Field Buffer ‘n’ Byte ‘m’ bits

Note 1: The Most Significant Byte contains byte (m + 1) of the buffer.

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x

— — — FILHIT<4:0>

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-13 Unimplemented: Read as ‘0’

bit 12-8 FILHIT<4:0>: Filter Hit Code bits (only written by module for receive buffers, unused for transmit buffers)

Encodes number of filter that resulted in writing this buffer.

bit 7-0 Unimplemented: Read as ‘0’

dsPIC33FJXXXGPX06A/X08A/X10A

20.0 DATA CONVERTER

INTERFACE (DCI) MODULE

20.1 Module Introduction

The dsPIC33FJXXXGPX06A/X08A/X10A Data Con-

verter Interface (DCI) module allows simple interfacing

of devices, such as audio coder/decoders (Codecs),

ADC and D/A converters. The following interfaces are

supported:

• Framed Synchronous Serial Transfer (Single or

Multi-Channel)

• Inter-IC Sound (I2S) Interface

• AC-Link Compliant mode

The DCI module provides the following general

features:

• Programmable word size up to 16 bits

• Supports up to 16 time slots, for a maximum

frame size of 256 bits

• Data buffering for up to 4 samples without CPU

overhead

20.2 Module I/O Pins

There are four I/O pins associated with the module.

When enabled, the module controls the data direction

of each of the four pins.

20.2.1 CSCK PIN

The CSCK pin provides the serial clock for the DCI

module. The CSCK pin may be configured as an input

or output using the CSCKD control bit in the DCICON1

SFR. When configured as an output, the serial clock is

provided by the dsPIC33FJXXXGPX06A/X08A/X10A.

When configured as an input, the serial clock must be

provided by an external device.

20.2.2 CSDO PIN

The Serial Data Output (CSDO) pin is configured as an

output only pin when the module is enabled. The

CSDO pin drives the serial bus whenever data is to be

transmitted. The CSDO pin is tri-stated, or driven to ‘0’,

during CSCK periods when data is not transmitted

depending on the state of the CSDOM control bit. This

allows other devices to place data on the serial bus

during transmission periods not used by the DCI

module.

20.2.3 CSDI PIN

The Serial Data Input (CSDI) pin is configured as an

input only pin when the module is enabled.

20.2.3.1 COFS Pin

The Codec Frame Synchronization (COFS) pin is used

to synchronize data transfers that occur on the CSDO

and CSDI pins. The COFS pin may be configured as an

input or an output. The data direction for the COFS pin

is determined by the COFSD control bit in the

DCICON1 register.

The DCI module accesses the shadow registers while

the CPU is in the process of accessing the memory

mapped buffer registers.

20.2.4 BUFFER DATA ALIGNMENT

Data values are always stored left justified in the

buffers since most Codec data is represented as a

signed 2’s complement fractional number. If the

received word length is less than 16 bits, the unused

Least Significant bits in the Receive Buffer registers are

set to ‘0’ by the module. If the transmitted word length

is less than 16 bits, the unused LSbs in the Transmit

Buffer register are ignored by the module. The word

length setup is described in subsequent sections of this

document.

20.2.5 TRANSMIT/RECEIVE SHIFT

The DCI module has a 16-bit shift register for shifting

serial data in and out of the module. Data is shifted in/

out of the shift register, MSb first, since audio PCM data

is transmitted in signed 2’s complement format.

20.2.6 DCI BUFFER CONTROL

The DCI module contains a buffer control unit for

transferring data between the shadow buffer memory

and the Serial Shift register. The buffer control unit is a

simple 2-bit address counter that points to word loca-

tions in the shadow buffer memory. For the receive

memory space (high address portion of DCI buffer

memory), the address counter is concatenated with a

‘0’ in the MSb location to form a 3-bit address. For the

transmit memory space (high portion of DCI buffer

memory), the address counter is concatenated with a

‘1’ in the MSb location.

Note 1: This data sheet summarizes the features

of the dsPIC33FJXXXGPX06A/X08A/

X10A family of devices. However, it is not

intended to be a comprehensive refer-

ence source. To complement the infor-

mation in this data sheet, refer to Section

20. “Data Converter Interface (DCI)”

(DS70288) in the “dsPIC33F/PIC24H

Family Reference Manual”, which is

available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Note: The DCI buffer control unit always

accesses the same relative location in the

transmit and receive buffers, so only one

address counter is provided.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 20-1: DCI MODULE BLOCK DIAGRAM

BCG Control bits

16-bit Data Bus

Sample Rate

Generator

SCKD

FSD

DCI Buffer

Frame

Synchronization

Generator

Control Unit

DCI Shift Register

Receive Buffer

Registers w/Shadow

FOSC/4

Word Size Selection bits

Frame Length Selection bits

DCI Mode Selection bits

CSCK

COFS

CSDI

CSDO

15 0

Transmit Buffer

Registers w/Shadow

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 U-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0

DCIEN —DCISIDL— DLOOP CSCKD CSCKE COFSD

bit 15 bit 8

R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 R/W-0 R/W-0

UNFM CSDOM DJST — — —COFSM<1:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 DCIEN: DCI Module Enable bit

1 = Module is enabled

0 = Module is disabled

bit 14 Unimplemented: Read as ‘0’

bit 13 DCISIDL: DCI Stop in Idle Control bit

1 = Module will halt in CPU Idle mode

0 = Module will continue to operate in CPU Idle mode

bit 12 Unimplemented: Read as ‘0’

bit 11 DLOOP: Digital Loopback Mode Control bit

1 = Digital Loopback mode is enabled. CSDI and CSDO pins internally connected

0 = Digital Loopback mode is disabled

bit 10 CSCKD: Sample Clock Direction Control bit

1 = CSCK pin is an input when DCI module is enabled

0 = CSCK pin is an output when DCI module is enabled

bit 9 CSCKE: Sample Clock Edge Control bit

1 = Data changes on serial clock falling edge, sampled on serial clock rising edge

0 = Data changes on serial clock rising edge, sampled on serial clock falling edge

bit 8 COFSD: Frame Synchronization Direction Control bit

1 = COFS pin is an input when DCI module is enabled

0 = COFS pin is an output when DCI module is enabled

bit 7 UNFM: Underflow Mode bit

1 = Transmit last value written to the transmit registers on a transmit underflow

0 = Transmit ‘0’s on a transmit underflow

bit 6 CSDOM: Serial Data Output Mode bit

1 = CSDO pin will be tri-stated during disabled transmit time slots

0 = CSDO pin drives ‘0’s during disabled transmit time slots

bit 5 DJST: DCI Data Justification Control bit

1 = Data transmission/reception is begun during the same serial clock cycle as the frame

synchronization pulse

0 = Data transmission/reception is begun one serial clock cycle after frame synchronization pulse

bit 4-2 Unimplemented: Read as ‘0’

bit 1-0 COFSM<1:0>: Frame Sync Mode bits

11 = 20-bit AC-Link mode

10 = 16-bit AC-Link mode

01 = I2S Frame Sync mode

00 = Multi-Channel Frame Sync mode

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 U-0 R/W-0 R/W-0 U-0 R/W-0

— — — — BLEN<1:0> —COFSG3

bit 15 bit 8

R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0

COFSG<2:0> — WS<3:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 Unimplemented: Read as ‘0’

bit 11-10 BLEN<1:0>: Buffer Length Control bits

11 = Four data words will be buffered between interrupts

10 = Three data words will be buffered between interrupts

01 = Two data words will be buffered between interrupts

00 = One data word will be buffered between interrupts

bit 9 Unimplemented: Read as ‘0’

bit 8-5 COFSG<3:0>: Frame Sync Generator Control bits

1111 = Data frame has 16 words

•

0010 = Data frame has 3 words

0001 = Data frame has 2 words

0000 = Data frame has 1 word

bit 4 Unimplemented: Read as ‘0’

bit 3-0 WS<3:0>: DCI Data Word Size bits

1111 = Data word size is 16 bits

•

0100 = Data word size is 5 bits

0011 = Data word size is 4 bits

0010 = Invalid Selection. Do not use. Unexpected results may occur

0001 = Invalid Selection. Do not use. Unexpected results may occur

0000 = Invalid Selection. Do not use. Unexpected results may occur

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0

— — — —BCG<11:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

BCG<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 Unimplemented: Read as ‘0’

bit 11-0 BCG<11:0>: DCI Bit Clock Generator Control bits

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 U-0 R-0 R-0 R-0 R-0

— — — — SLOT<3:0>

bit 15 bit 8

U-0 U-0 U-0 U-0 R-0 R-0 R-0 R-0

— — — — ROV RFUL TUNF TMPTY

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 Unimplemented: Read as ‘0’

bit 11-8 SLOT<3:0>: DCI Slot Status bits

1111 = Slot #15 is currently active

•

0010 = Slot #2 is currently active

0001 = Slot #1 is currently active

0000 = Slot #0 is currently active

bit 7-4 Unimplemented: Read as ‘0’

bit 3 ROV: Receive Overflow Status bit

1 = A receive overflow has occurred for at least one receive register

0 = A receive overflow has not occurred

bit 2 RFUL: Receive Buffer Full Status bit

1 = New data is available in the receive registers

0 = The receive registers have old data

bit 1 TUNF: Transmit Buffer Underflow Status bit

1 = A transmit underflow has occurred for at least one transmit register

0 = A transmit underflow has not occurred

bit 0 TMPTY: Transmit Buffer Empty Status bit

1 = The transmit registers are empty

0 = The transmit registers are not empty

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

RSE15 RSE14 RSE13 RSE12 RSE11 RSE10 RSE9 RSE8

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

RSE7 RSE6 RSE5 RSE4 RSE3 RSE2 RSE1 RSE0

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 RSE<15:0>: Receive Slot Enable bits

1 = CSDI data is received during the individual time slot n

0 = CSDI data is ignored during the individual time slot n

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

TSE15 TSE14 TSE13 TSE12 TSE11 TSE10 TSE9 TSE8

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

TSE7 TSE6 TSE5 TSE4 TSE3 TSE2 TSE1 TSE0

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 TSE<15:0>: Transmit Slot Enable Control bits

1 = Transmit buffer contents are sent during the individual time slot n

0 = CSDO pin is tri-stated or driven to logic ‘0’, during the individual time slot, depending on the state

of the CSDOM bit

dsPIC33FJXXXGPX06A/X08A/X10A

NOTES:

dsPIC33FJXXXGPX06A/X08A/X10A

21.0 10-BIT/12-BIT

ANALOG-TO-DIGITAL

CONVERTER (ADC)

The dsPIC33FJXXXGPX06A/X08A/X10A devices

have up to 32 ADC input channels. These devices also

have up to 2 ADC modules (ADCx, where ‘x’ = 1 or 2),

each with its own set of Special Function Registers.

The AD12B bit (ADxCON1<10>) allows each of the

ADC modules to be configured by the user as either a

10-bit, 4-sample/hold ADC (default configuration) or a

12-bit, 1-sample/hold ADC.

21.1 Key Features

The 10-bit ADC configuration has the following key

features:

• Successive Approximation (SAR) conversion

• Conversion speeds of up to 1.1 Msps

• Up to 32 analog input pins

• External voltage reference input pins

• Simultaneous sampling of up to four analog input

pins

• Automatic Channel Scan mode

• Selectable conversion trigger source

• Selectable Buffer Fill modes

• Four result alignment options (signed/unsigned,

fractional/integer)

• Operation during CPU Sleep and Idle modes

The 12-bit ADC configuration supports all the above

features, except:

• In the 12-bit configuration, conversion speeds of

up to 500 ksps are supported

• There is only 1 sample/hold amplifier in the 12-bit

configuration, so simultaneous sampling of

multiple channels is not supported.

Depending on the particular device pinout, the ADC

can have up to 32 analog input pins, designated AN0

through AN31. In addition, there are two analog input

pins for external voltage reference connections. These

voltage reference inputs may be shared with other

analog input pins. The actual number of analog input

pins and external voltage reference input configuration

will depend on the specific device. Refer to the device

data sheet for further details.

A block diagram of the ADC is shown in Figure 21-1.

21.2 ADC Initialization

The following configuration steps should be performed.

1. Configure the ADC module:

a) Select port pins as analog inputs

(ADxPCFGH<15:0> or ADxPCFGL<15:0>).

b) Select voltage reference source to match

expected range on analog inputs

(ADxCON2<15:13>).

c) Select the analog conversion clock to match

desired data rate with processor clock

(ADxCON3<7:0>).

d) Determine how many S/H channels will be

used (ADxCON2<9:8> and

ADxPCFGH<15:0> or ADxPCFGL<15:0>).

e) Select the appropriate sample/conversion

sequence (ADxCON1<7:5> and

ADxCON3<12:8>).

f) Select how conversion results are presented

in the buffer (ADxCON1<9:8>).

g) Turn on ADC module (ADxCON1<15>).

2. Configure ADC interrupt (if required):

a) Clear the ADxIF bit.

b) Select ADC interrupt priority.

21.3 ADC and DMA

If more than one conversion result needs to be buffered

before triggering an interrupt, DMA data transfers can

be used. Both ADC1 and ADC2 can trigger a DMA data

transfer. If ADC1 or ADC2 is selected as the DMA IRQ

source, a DMA transfer occurs when the AD1IF or

AD2IF bit gets set as a result of an ADC1 or ADC2

sample conversion sequence.

The SMPI<3:0> bits (ADxCON2<5:2>) are used to

select how often the DMA RAM buffer pointer is

incremented.

The ADDMABM bit (ADxCON1<12>) determines how

the conversion results are filled in the DMA RAM buffer

area being used for ADC. If this bit is set, DMA buffers

are written in the order of conversion. The module will

provide an address to the DMA channel that is the

same as the address used for the non-DMA

stand-alone buffer. If the ADDMABM bit is cleared, then

DMA buffers are written in Scatter/Gather mode. The

module will provide a scatter/gather address to the

DMA channel, based on the index of the analog input

and the size of the DMA buffer.

Note 1: This data sheet summarizes the fea-

tures of the dsPIC33FJXXXGPX06A/

X08A/X10A family of devices. How-

ever, it is not intended to be a compre-

hensive reference source. To

complement the information in this data

sheet, refer to Section 16. “Ana-

log-to-Digital Converter (ADC)”

(DS70183) in the “dsPIC33F/PIC24H

Family Reference Manual”, which is

available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Note: The ADC module needs to be disabled

before modifying the AD12B bit.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 21-1: ADCx MODULE BLOCK DIAGRAM

SAR ADC

S/H0

S/H1

ADC1BUF0

AN0

ANy(3)

AN1

VREFL

CH0SB<4:0>

CH0NA CH0NB

AN0

AN3

CH123SA

AN9

VREFL

CH123SB

CH123NA CH123NB

AN6

S/H2

AN1

AN4

CH123SA

AN10

VREFL

CH123SB

CH123NA CH123NB

AN7

S/H3

AN2

AN5

CH123SA

AN11

VREFL

CH123SB

CH123NA CH123NB

AN8

CH1(2)

CH0

CH2(2)

CH3(2)

CH0SA<4:0>

CHANNEL

SCAN

CSCNA

Alternate

Note 1: VREF+, VREF- inputs can be multiplexed with other analog inputs.

2: Channels 1, 2 and 3 are not applicable for the 12-bit mode of operation.

3: For 64-pin devices, y = 17; for 80-pin devices, y = 23; for 100-pin devices, y = 31; for ADC2, y = 15.

Input Selection

VREFH VREFL

AVDD AVSS

VREF-(1)

VREF+(1)

VCFG<2:0>

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 21-2: ADC CONVERSION CLOCK PERIOD BLOCK DIAGRAM

ADC Internal

RC Clock(2)

TOSC(1) X2

ADC Conversion

Clock Multiplier

1, 2, 3, 4, 5,..., 64

ADxCON3<15>

TCY

TAD

ADxCON3<5:0>

Note 1: Refer to Figure 9-2 for the derivation of FOSC when the PLL is enabled. If the PLL is not used, FOSC is equal to

the clock source frequency. TOSC = 1/FOSC.

2: See the ADC electrical specifications for the exact RC clock value.

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 U-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0

ADON —ADSIDLADDMABM— AD12B FORM<1:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0

HC,HS

R/C-0

HC, HS

SSRC<2:0> — SIMSAM ASAM SAMP DONE

bit 7 bit 0

Legend: HC = Cleared by hardware HS = Set by hardware C = Clear only bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 ADON: ADC Operating Mode bit

1 = ADC module is operating

0 = ADC is off

bit 14 Unimplemented: Read as ‘0’

bit 13 ADSIDL: Stop in Idle Mode bit

1 = Discontinue module operation when device enters Idle mode

0 = Continue module operation in Idle mode

bit 12 ADDMABM: DMA Buffer Build Mode bit

1 = DMA buffers are written in the order of conversion. The module will provide an address to the DMA

channel that is the same as the address used for the non-DMA stand-alone buffer

0 = DMA buffers are written in Scatter/Gather mode. The module will provide a scatter/gather address

to the DMA channel, based on the index of the analog input and the size of the DMA buffer

bit 11 Unimplemented: Read as ‘0’

bit 10 AD12B: 10-Bit or 12-Bit Operation Mode bit

1 = 12-bit, 1-channel ADC operation

0 = 10-bit, 4-channel ADC operation

bit 9-8 FORM<1:0>: Data Output Format bits

For 10-bit operation:

11 = Signed fractional (DOUT = sddd dddd dd00 0000, where s = .NOT.d<9>)

10 = Fractional (DOUT = dddd dddd dd00 0000)

01 = Signed integer (DOUT = ssss sssd dddd dddd, where s = .NOT.d<9>)

00 = Integer (DOUT = 0000 00dd dddd dddd)

For 12-bit operation:

11 = Signed fractional (DOUT = sddd dddd dddd 0000, where s = .NOT.d<11>)

10 = Fractional (DOUT = dddd dddd dddd 0000)

01 = Signed Integer (DOUT = ssss sddd dddd dddd, where s = .NOT.d<11>)

00 = Integer (DOUT = 0000 dddd dddd dddd)

bit 7-5 SSRC<2:0>: Sample Clock Source Select bits

111 = Internal counter ends sampling and starts conversion (auto-convert)

110 = Reserved

101 = Reserved

100 = GP timer (Timer5 for ADC1, Timer3 for ADC2) compare ends sampling and starts conversion

011 = Reserved

010 = GP timer (Timer3 for ADC1, Timer5 for ADC2) compare ends sampling and starts conversion

001 = Active transition on INT0 pin ends sampling and starts conversion

000 = Clearing sample bit ends sampling and starts conversion

bit 4 Unimplemented: Read as ‘0’

dsPIC33FJXXXGPX06A/X08A/X10A

bit 3 SIMSAM: Simultaneous Sample Select bit (only applicable when CHPS<1:0> = 01 or 1x)

When AD12B = 1, SIMSAM is: U-0, Unimplemented, Read as ‘0’

1 = Samples CH0, CH1, CH2, CH3 simultaneously (when CHPS<1:0> = 1x); or

Samples CH0 and CH1 simultaneously (when CHPS<1:0> = 01)

0 = Samples multiple channels individually in sequence

bit 2 ASAM: ADC Sample Auto-Start bit

1 = Sampling begins immediately after last conversion. SAMP bit is auto-set

0 = Sampling begins when SAMP bit is set

bit 1 SAMP: ADC Sample Enable bit

1 = ADC sample/hold amplifiers are sampling

0 = ADC sample/hold amplifiers are holding

If ASAM = 0, software may write ‘1’ to begin sampling. Automatically set by hardware if ASAM = 1.

If SSRC = 000, software may write ‘0’ to end sampling and start conversion. If SSRC ≠ 000,

automatically cleared by hardware to end sampling and start conversion.

bit 0 DONE: ADC Conversion Status bit

1 = ADC conversion cycle is completed

0 = ADC conversion not started or in progress

Automatically set by hardware when ADC conversion is complete. Software may write ‘0’ to clear

DONE status (software not allowed to write ‘1’). Clearing this bit will NOT affect any operation in prog-

ress. Automatically cleared by hardware at start of a new conversion.

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0

VCFG<2:0> —— CSCNA CHPS<1:0>

bit 15 bit 8

R-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

BUFS — SMPI<3:0> BUFM ALTS

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-13 VCFG<2:0>: Converter Voltage Reference Configuration bits

bit 12-11 Unimplemented: Read as ‘0’

bit 10 CSCNA: Scan Input Selections for CH0+ during Sample A bit

1 = Scan inputs

0 = Do not scan inputs

bit 9-8 CHPS<1:0>: Selects Channels Utilized bits

When AD12B = 1, CHPS<1:0> is: U-0, Unimplemented, Read as ‘0’

1x = Converts CH0, CH1, CH2 and CH3

01 = Converts CH0 and CH1

00 = Converts CH0

bit 7 BUFS: Buffer Fill Status bit (only valid when BUFM = 1)

1 = ADC is currently filling second half of buffer, user should access data in first half

0 = ADC is currently filling first half of buffer, user should access data in second half

bit 6 Unimplemented: Read as ‘0’

bit 5-2 SMPI<3:0>: Selects Increment Rate for DMA Addresses bits or number of sample/conversion

operations per interrupt

1111 = Increments the DMA address or generates interrupt after completion of every 16th sample/

conversion operation

1110 = Increments the DMA address or generates interrupt after completion of every 15th sample/

conversion operation

•

0001 = Increments the DMA address or generates interrupt after completion of every 2nd sample/

conversion operation

0000 = Increments the DMA address or generates interrupt after completion of every sample/conver-

sion operation

bit 1 BUFM: Buffer Fill Mode Select bit

1 = Starts filling first half of buffer on first interrupt and second half of the buffer on next interrupt

0 = Always starts filling buffer from the beginning

bit 0 ALTS: Alternate Input Sample Mode Select bit

1 = Uses channel input selects for Sample A on first sample and Sample B on next sample

0 = Always uses channel input selects for Sample A

VREF+VREF-

000 AVDD AVSS

001 External VREF+AVSS

010 AVDD External VREF-

011 External VREF+ External VREF-

1xx AVDD Avss

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

ADRC —— SAMC<4:0>(1)

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

ADCS<7:0>(2)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 ADRC: ADC Conversion Clock Source bit

1 = ADC internal RC clock

0 = Clock derived from system clock

bit 14-13 Unimplemented: Read as ‘0’

bit 12-8 SAMC<4:0>: Auto Sample Time bits(1)

11111 = 31 TAD

•

00001 = 1 TAD

00000 = 0 TAD

bit 7-0 ADCS<7:0>: ADC Conversion Clock Select bits(2)

11111111 = Reserved

•

01000000 = Reserved

00111111 = TCY · (ADCS<7:0> + 1) = 64 · TCY = TAD

•

00000010 = TCY · (ADCS<7:0> + 1) = 3 · TCY = TAD

00000001 = TCY · (ADCS<7:0> + 1) = 2 · TCY = TAD

00000000 = TCY · (ADCS<7:0> + 1) = 1 · TCY = TAD

Note 1: This bit only used if ADxCON1<7:5> (SSRC<2:0>) = 111.

2: This bit is not used if ADxCON3<15> (ADRC) = 1.

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0

— — — — — DMABL<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-3 Unimplemented: Read as ‘0’

bit 2-0 DMABL<2:0>: Selects Number of DMA Buffer Locations per Analog Input bits

111 = Allocates 128 words of buffer to each analog input

110 = Allocates 64 words of buffer to each analog input

101 = Allocates 32 words of buffer to each analog input

100 = Allocates 16 words of buffer to each analog input

011 = Allocates 8 words of buffer to each analog input

010 = Allocates 4 words of buffer to each analog input

001 = Allocates 2 words of buffer to each analog input

000 = Allocates 1 word of buffer to each analog input

dsPIC33FJXXXGPX06A/X08A/X10A

U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0

— — — — — CH123NB<1:0> CH123SB

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0

— — — — — CH123NA<1:0> CH123SA

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-11 Unimplemented: Read as ‘0’

bit 10-9 CH123NB<1:0>: Channel 1, 2, 3 Negative Input Select for Sample B bits

When AD12B = 1, CHxNB is: U-0, Unimplemented, Read as ‘0’

11 = CH1 negative input is AN9, CH2 negative input is AN10, CH3 negative input is AN11

10 = CH1 negative input is AN6, CH2 negative input is AN7, CH3 negative input is AN8

0x = CH1, CH2, CH3 negative input is VREF-

bit 8 CH123SB: Channel 1, 2, 3 Positive Input Select for Sample B bit

When AD12B = 1, CHxSB is: U-0, Unimplemented, Read as ‘0’

1 = CH1 positive input is AN3, CH2 positive input is AN4, CH3 positive input is AN5

0 = CH1 positive input is AN0, CH2 positive input is AN1, CH3 positive input is AN2

bit 7-3 Unimplemented: Read as ‘0’

bit 2-1 CH123NA<1:0>: Channel 1, 2, 3 Negative Input Select for Sample A bits

When AD12B = 1, CHxNA is: U-0, Unimplemented, Read as ‘0’

11 = CH1 negative input is AN9, CH2 negative input is AN10, CH3 negative input is AN11

10 = CH1 negative input is AN6, CH2 negative input is AN7, CH3 negative input is AN8

0x = CH1, CH2, CH3 negative input is VREF-

bit 0 CH123SA: Channel 1, 2, 3 Positive Input Select for Sample A bit

When AD12B = 1, CHxSA is: U-0, Unimplemented, Read as ‘0’

1 = CH1 positive input is AN3, CH2 positive input is AN4, CH3 positive input is AN5

0 = CH1 positive input is AN0, CH2 positive input is AN1, CH3 positive input is AN2

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

CH0NB —— CH0SB<4:0>(1)

bit 15 bit 8

R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

CH0NA —— CH0SA<4:0>(1)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 CH0NB: Channel 0 Negative Input Select for Sample B bit

Same definition as bit 7.

bit 14-13 Unimplemented: Read as ‘0’

bit 12-8 CH0SB<4:0>: Channel 0 Positive Input Select for Sample B bits(1)

11111 = Channel 0 positive input is AN31

11110 = Channel 0 positive input is AN30

•

00010 = Channel 0 positive input is AN2

00001 = Channel 0 positive input is AN1

00000 = Channel 0 positive input is AN0

bit 7 CH0NA: Channel 0 Negative Input Select for Sample A bit

1 = Channel 0 negative input is AN1

0 = Channel 0 negative input is VREF-

bit 6-5 Unimplemented: Read as ‘0’

bit 4-0 CH0SA<4:0>: Channel 0 Positive Input Select for Sample A bits(1)

11111 = Channel 0 positive input is AN31

11110 = Channel 0 positive input is AN30

•

00010 = Channel 0 positive input is AN2

00001 = Channel 0 positive input is AN1

00000 = Channel 0 positive input is AN0

Note 1: ADC2 can only select AN0 through AN15 as positive input.

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

CSS31 CSS30 CSS29 CSS28 CSS27 CSS26 CSS25 CSS24

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

CSS23 CSS22 CSS21 CSS20 CSS19 CSS18 CSS17 CSS16

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 CSS<31:16>: ADC Input Scan Selection bits

1 = Select ANx for input scan

0 = Skip ANx for input scan

Note 1: On devices without 32 analog inputs, all ADxCSSH bits may be selected by user. However, inputs selected

for scan without a corresponding input on device will convert VREFL.

2: CSSx = ANx, where x = 16 through 31.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

CSS15 CSS14 CSS13 CSS12 CSS11 CSS10 CSS9 CSS8

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

CSS7 CSS6 CSS5 CSS4 CSS3 CSS2 CSS1 CSS0

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 CSS<15:0>: ADC Input Scan Selection bits

1 = Select ANx for input scan

0 = Skip ANx for input scan

Note 1: On devices without 16 analog inputs, all ADxCSSL bits may be selected by user. However, inputs selected

for scan without a corresponding input on device will convert VREF-.

2: CSSx = ANx, where x = 0 through 15.

dsPIC33FJXXXGPX06A/X08A/X10A

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PCFG31 PCFG30 PCFG29 PCFG28 PCFG27 PCFG26 PCFG25 PCFG24

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PCFG23 PCFG22 PCFG21 PCFG20 PCFG19 PCFG18 PCFG17 PCFG16

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 PCFG<31:16>: ADC Port Configuration Control bits

1 = Port pin in Digital mode, port read input enabled, ADC input multiplexer connected to AVSS

0 = Port pin in Analog mode, port read input disabled, ADC samples pin voltage

Note 1: On devices without 32 analog inputs, all PCFG bits are R/W by user. However, PCFG bits are ignored on

ports without a corresponding input on device.

2: ADC2 only supports analog inputs AN0-AN15; therefore, no ADC2 port Configuration register exists.

3: PCFGx = ANx, where x = 16 through 31.

4: PCFGx bits have no effect if ADC module is disabled by setting ADxMD bit in the PMDx register. In this

case all port pins multiplexed with ANx will be in Digital mode.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PCFG15 PCFG14 PCFG13 PCFG12 PCFG11 PCFG10 PCFG9 PCFG8

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PCFG7 PCFG6 PCFG5 PCFG4 PCFG3 PCFG2 PCFG1 PCFG0

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 PCFG<15:0>: ADC Port Configuration Control bits

1 = Port pin in Digital mode, port read input enabled, ADC input multiplexer connected to AVSS

0 = Port pin in Analog mode, port read input disabled, ADC samples pin voltage

Note 1: On devices without 16 analog inputs, all PCFG bits are R/W by user. However, PCFG bits are ignored on

ports without a corresponding input on device.

2: On devices with two analog-to-digital modules, both AD1PCFGL and AD2PCFGL will affect the

configuration of port pins multiplexed with AN0-AN15.

3: PCFGx = ANx, where x = 0 through 15.

4: PCFGx bits have no effect if ADC module is disabled by setting ADxMD bit in the PMDx register. In this

case all port pins multiplexed with ANx will be in Digital mode

dsPIC33FJXXXGPX06A/X08A/X10A

22.0 SPECIAL FEATURES

dsPIC33FJXXXGPX06A/X08A/X10A devices include

the following features intended to maximize application

flexibility and reliability, and minimize cost through elim-

ination of external components:

• Flexible Configuration

• Watchdog Timer (WDT)

• Code Protection and CodeGuard™ Security

• JTAG Boundary Scan Interface

• In-Circuit Serial Programming™ (ICSP™)

• In-Circuit Emulation

22.1 Configuration Bits

dsPIC33FJXXXGPX06A/X08A/X10A devices provide

nonvolatile memory implementation for device

configuration bits. Refer to Section 25. “Device Con-

figuration” (DS70194) of the “dsPIC33F/PIC24H

Family Reference Manual”, for more information on this

implementation.

The Configuration bits can be programmed (read as

‘0’), or left unprogrammed (read as ‘1’), to select

various device configurations. These bits are mapped

starting at program memory location 0xF80000.

The device Configuration register map is shown in

Table 22-1.

The individual Configuration bit descriptions for the

Configuration registers are shown in Table 22-2.

Note that address 0xF80000 is beyond the user program

memory space. In fact, it belongs to the configuration

memory space (0x800000-0xFFFFFF) which can only be

accessed using table reads and table writes.

TABLE 22-1: DEVICE CONFIGURATION REGISTER MAP

Note 1: This data sheet summarizes the features

of the dsPIC33FJXXXGPX06A/X08A/

X10A family of devices. However, it is not

intended to be a comprehensive refer-

ence source. To complement the infor-

mation in this data sheet, refer to Section

23. “CodeGuard™ Security”

(DS70199), Section 24. “Programming

and Diagnostics” (DS70207), and Sec-

tion 25. “Device Configuration”

(DS70194) in the “dsPIC33F/PIC24H

Family Reference Manual”, which are

available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

0xF80000 FBS RBS<1:0> —— BSS<2:0> BWRP

0xF80002 FSS RSS<1:0> —— SSS<2:0> SWRP

0xF80004 FGS — — — — — GSS1 GSS0 GWRP

0xF80006 FOSCSEL IESO Reserved(2) — — —FNOSC<2:0>

0xF80008 FOSC FCKSM<1:0> — — — OSCIOFNC POSCMD<1:0>

0xF8000A FWDT FWDTEN WINDIS PLLKEN(3) WDTPRE WDTPOST<3:0>

0xF8000C FPOR Reserved(4) ——FPWRT<2:0>

0xF8000E FICD Reserved(1) JTAGEN — — —ICS<1:0>

0xF80010 FUID0 User Unit ID Byte 0

0xF80012 FUID1 User Unit ID Byte 1

0xF80014 FUID2 User Unit ID Byte 2

0xF80016 FUID3 User Unit ID Byte 3

Legend: — = unimplemented bit, read as ‘0’.

Note 1: These bits are reserved for use by development tools and must be programmed as ‘1’.

2: When read, this bit returns the current programmed value.

3: This bit is unimplemented on dsPIC33FJ64GPX06A/X08A/X10A and dsPIC33FJ128GPX06A/X08A/X10A

devices and reads as ‘0’.

4: These bits are reserved and always read as ‘1’.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 22-2: dsPIC33FJXXXGPX06A/X08A/X10A CONFIGURATION BITS DESCRIPTION

Bit Field Register RTSP

Effect Description

BWRP FBS Immediate Boot Segment Program Flash Write Protection

1 = Boot segment may be written

0 = Boot segment is write-protected

BSS<2:0> FBS Immediate Boot Segment Program Flash Code Protection Size

X11 = No Boot program Flash segment

Boot space is 1K IW less VS

110 = Standard security; boot program Flash segment starts at End of VS,

ends at 0007FEh

010 = High security; boot program Flash segment starts at End of VS, ends

at 0007FEh

Boot space is 4K IW less VS

101 = Standard security; boot program Flash segment starts at End of VS,

ends at 001FFEh

001 = High security; boot program Flash segment starts at End of VS, ends

at 001FFEh

Boot space is 8K IW less VS

100 = Standard security; boot program Flash segment starts at End of VS,

ends at 003FFEh

000 = High security; boot program Flash segment starts at End of VS, ends

at 003FFEh

RBS<1:0> FBS Immediate Boot Segment RAM Code Protection

11 = No Boot RAM defined

10 = Boot RAM is 128 Bytes

01 = Boot RAM is 256 Bytes

00 = Boot RAM is 1024 Bytes

SWRP FSS Immediate Secure Segment Program Flash Write Protection

1 = Secure segment may be written

0 = Secure segment is write-protected

dsPIC33FJXXXGPX06A/X08A/X10A

SSS<2:0> FSS Immediate Secure Segment Program Flash Code Protection Size

(FOR 128K and 256K DEVICES)

X11 = No Secure program Flash segment

Secure space is 8K IW less BS

110 = Standard security; secure program Flash segment starts at End of

BS, ends at 0x003FFE

010 = High security; secure program Flash segment starts at End of BS,

ends at 0x003FFE

Secure space is 16K IW less BS

101 = Standard security; secure program Flash segment starts at End of

BS, ends at 0x007FFE

001 = High security; secure program Flash segment starts at End of BS,

ends at 0x007FFE

Secure space is 32K IW less BS

100 = Standard security; secure program Flash segment starts at End of

BS, ends at 0x00FFFE

000 = High security; secure program Flash segment starts at End of BS,

ends at 0x00FFFE

(FOR 64K DEVICES)

X11 = No Secure program Flash segment

Secure space is 4K IW less BS

110 = Standard security; secure program Flash segment starts at End of

BS, ends at 0x001FFE

010 = High security; secure program Flash segment starts at End of BS,

ends at 0x001FFE

Secure space is 8K IW less BS

101 = Standard security; secure program Flash segment starts at End of

BS, ends at 0x003FFE

001 = High security; secure program Flash segment starts at End of BS,

ends at 0x003FFE

Secure space is 16K IW less BS

100 = Standard security; secure program Flash segment starts at End of

BS, ends at 007FFEh

000 = High security; secure program Flash segment starts at End of BS,

ends at 0x007FFE

RSS<1:0> FSS Immediate Secure Segment RAM Code Protection

11 = No Secure RAM defined

10 = Secure RAM is 256 Bytes less BS RAM

01 = Secure RAM is 2048 Bytes less BS RAM

00 = Secure RAM is 4096 Bytes less BS RAM

GSS<1:0> FGS Immediate General Segment Code-Protect bit

11 = User program memory is not code-protected

10 = Standard security; general program Flash segment starts at End of

SS, ends at EOM

0x = High security; general program Flash segment starts at End of SS,

ends at EOM

TABLE 22-2: dsPIC33FJXXXGPX06A/X08A/X10A CONFIGURATION BITS DESCRIPTION (CONTINUED)

Bit Field Register RTSP

Effect Description

dsPIC33FJXXXGPX06A/X08A/X10A

GWRP FGS Immediate General Segment Write-Protect bit

1 = User program memory is not write-protected

0 = User program memory is write-protected

IESO FOSCSEL Immediate Two-speed Oscillator Start-up Enable bit

1 = Start-up device with FRC, then automatically switch to the user-selected

oscillator source when ready

0 = Start-up device with user-selected oscillator source

FNOSC<2:0> FOSCSEL If clock

switch is

enabled,

RTSP

effect is

on any

device

Reset;

otherwise,

Immediate

Initial Oscillator Source Selection bits

111 = Internal Fast RC (FRC) oscillator with postscaler

110 = Internal Fast RC (FRC) oscillator with divide-by-16

101 = LPRC oscillator

100 = Secondary (LP) oscillator

011 = Primary (XT, HS, EC) oscillator with PLL

010 = Primary (XT, HS, EC) oscillator

001 = Internal Fast RC (FRC) oscillator with PLL

000 = FRC oscillator

FCKSM<1:0> FOSC Immediate Clock Switching Mode bits

1x = Clock switching is disabled, Fail-Safe Clock Monitor is disabled

01 = Clock switching is enabled, Fail-Safe Clock Monitor is disabled

00 = Clock switching is enabled, Fail-Safe Clock Monitor is enabled

OSCIOFNC FOSC Immediate OSC2 Pin Function bit (except in XT and HS modes)

1 = OSC2 is clock output

0 = OSC2 is general purpose digital I/O pin

POSCMD<1:0> FOSC Immediate Primary Oscillator Mode Select bits

11 = Primary oscillator disabled

10 = HS Crystal Oscillator mode

01 = XT Crystal Oscillator mode

00 = EC (External Clock) mode

FWDTEN FWDT Immediate Watchdog Timer Enable bit

1 = Watchdog Timer always enabled (LPRC oscillator cannot be disabled.

Clearing the SWDTEN bit in the RCON register will have no effect.)

0 = Watchdog Timer enabled/disabled by user software (LPRC can be dis-

abled by clearing the SWDTEN bit in the RCON register)

WINDIS FWDT Immediate Watchdog Timer Window Enable bit

1 = Watchdog Timer in Non-Window mode

0 = Watchdog Timer in Window mode

PLLKEN FWDT Immediate PLL Lock Enable bit

1 = Clock switch to PLL source will wait until the PLL lock signal is valid.

0 = Clock switch will not wait for the PLL lock signal.

WDTPRE FWDT Immediate Watchdog Timer Prescaler bit

1 = 1:128

0 = 1:32

WDTPOST FWDT Immediate Watchdog Timer Postscaler bits

1111 = 1:32,768

1110 = 1:16,384

•

0001 = 1:2

0000 = 1:1

TABLE 22-2: dsPIC33FJXXXGPX06A/X08A/X10A CONFIGURATION BITS DESCRIPTION (CONTINUED)

Bit Field Register RTSP

Effect Description

dsPIC33FJXXXGPX06A/X08A/X10A

FPWRT<2:0> FPOR Immediate Power-on Reset Timer Value Select bits

111 = PWRT = 128 ms

110 = PWRT = 64 ms

101 = PWRT = 32 ms

100 = PWRT = 16 ms

011 = PWRT = 8 ms

010 = PWRT = 4 ms

001 = PWRT = 2 ms

000 = PWRT = Disabled

JTAGEN FICD Immediate JTAG Enable bits

1 = JTAG enabled

0 = JTAG disabled

ICS<1:0> FICD Immediate ICD Communication Channel Select bits

11 = Communicate on PGEC1 and PGED1

10 = Communicate on PGEC2 and PGED2

01 = Communicate on PGEC3 and PGED3

00 = Reserved

TABLE 22-2: dsPIC33FJXXXGPX06A/X08A/X10A CONFIGURATION BITS DESCRIPTION (CONTINUED)

Bit Field Register RTSP

Effect Description

dsPIC33FJXXXGPX06A/X08A/X10A

22.2 On-Chip Voltage Regulator

All of the dsPIC33FJXXXGPX06A/X08A/X10A devices

power their core digital logic at a nominal 2.5V. This

may create an issue for designs that are required to

operate at a higher typical voltage, such as 3.3V. To

simplify system design, all devices in the

dsPIC33FJXXXGPX06A/X08A/X10A family incor-

porate an on-chip regulator that allows the device to

run its core logic from VDD.

The regulator provides power to the core from the

other VDD pins. The regulator requires that a

low-ESR (less than 5 ohms) capacitor (such as

tantalum or ceramic) be connected to the VCAP pin

(Figure 22-1). This helps to maintain the stability of

the regulator. The recommended value for the filter

capacitor is provided in Table 25-13 of Section 25.0

“Electrical Characteristics”.

On a POR, it takes approximately 20 μs for the on-chip

voltage regulator to generate an output voltage. During

this time, designated as TSTARTUP, code execution is

disabled. TSTARTUP is applied every time the device

resumes operation after any power-down.

FIGURE 22-1: CONNECTIONS FOR THE

ON-CHIP VOLTAGE

REGULATOR(1)

22.3 BOR: Brown-out Reset

The BOR (Brown-out Reset) module is based on an

internal voltage reference circuit that monitors the

regulated voltage VCAP. The main purpose of the BOR

module is to generate a device Reset when a

brown-out condition occurs. Brown-out conditions are

generally caused by glitches on the AC mains (i.e.,

missing portions of the AC cycle waveform due to bad

power transmission lines or voltage sags due to

excessive current draw when a large inductive load is

turned on).

A BOR will generate a Reset pulse which will reset the

device. The BOR will select the clock source, based on

the device Configuration bit values (FNOSC<2:0> and

POSCMD<1:0>). Furthermore, if an oscillator mode is

selected, the BOR will activate the Oscillator Start-up

Timer (OST). The system clock is held until OST

expires. If the PLL is used, then the clock will be held

until the LOCK bit (OSCCON<5>) is ‘1’.

Concurrently, the PWRT time-out (TPWRT) will be

applied before the internal Reset is released. If

TPWRT = 0 and a crystal oscillator is being used, then

a nominal delay of TFSCM = 100 is applied. The total

delay in this case is TFSCM.

The BOR Status bit (RCON<1>) will be set to indicate

that a BOR has occurred. The BOR circuit continues to

operate while in Sleep or Idle modes and will reset the

device should VDD fall below the BOR threshold

voltage.

Note: It is important for the low-ESR capacitor to

be placed as close as possible to the VCAP

pin.

Note 1: These are typical operating voltages. Refer to

Table 25-13 located in Section 25.1 “DC

Characteristics” for the full operating ranges

of VDD and VCAP.

2: It is important for the low-ESR capacitor to be

placed as close as possible to the VCAP pin.

VDD

VCAP

VSS

dsPIC33F

CEFC

3.3V

dsPIC33FJXXXGPX06A/X08A/X10A

22.4 Watchdog Timer (WDT)

For dsPIC33FJXXXGPX06A/X08A/X10A devices, the

WDT is driven by the LPRC oscillator. When the WDT

is enabled, the clock source is also enabled.

The nominal WDT clock source from LPRC is 32 kHz.

This feeds a prescaler and then can be configured for

either 5-bit (divide-by-32) or 7-bit (divide-by-128)

operation. The prescaler is set by the WDTPRE

Configuration bit. With a 32 kHz input, the prescaler

yields a nominal WDT time-out period (TWDT) of 1 ms

in 5-bit mode, or 4 ms in 7-bit mode.

A variable postscaler divides down the WDT prescaler

output and allows for a wide range of time-out periods.

The postscaler is controlled by the WDTPOST<3:0>

Configuration bits (FWDT<3:0>) which allow the

selection of a total of 16 settings, from 1:1 to 1:32,768.

Using the prescaler and postscaler, time-out periods

ranging from 1 ms to 131 seconds can be achieved.

The WDT, prescaler and postscaler are reset:

• On any device Reset

• On the completion of a clock switch, whether

invoked by software (i.e., setting the OSWEN bit

after changing the NOSC bits) or by hardware

(i.e., Fail-Safe Clock Monitor)

• When a PWRSAV instruction is executed

(i.e., Sleep or Idle mode is entered)

• When the device exits Sleep or Idle mode to

resume normal operation

•By a CLRWDT instruction during normal execution

If the WDT is enabled, it will continue to run during Sleep

or Idle modes. When the WDT time-out occurs, the

device will wake the device and code execution will

continue from where the PWRSAV instruction was

executed. The corresponding SLEEP or IDLE bits

(RCON<3,2>) will need to be cleared in software after the

device wakes up.

The WDT flag bit, WDTO (RCON<4>), is not automatically

cleared following a WDT time-out. To detect subsequent

WDT events, the flag must be cleared in software.

The WDT is enabled or disabled by the FWDTEN

Configuration bit in the FWDT Configuration register.

When the FWDTEN Configuration bit is set, the WDT is

always enabled.

The WDT can be optionally controlled in software when

the FWDTEN Configuration bit has been programmed

to ‘0’. The WDT is enabled in software by setting the

SWDTEN control bit (RCON<5>). The SWDTEN

control bit is cleared on any device Reset. The software

WDT option allows the user to enable the WDT for

critical code segments and disable the WDT during

non-critical segments for maximum power savings.

FIGURE 22-2: WDT BLOCK DIAGRAM

Note: The CLRWDT and PWRSAV instructions

clear the prescaler and postscaler counts

when executed.

Note: If the WINDIS bit (FWDT<6>) is cleared,

the CLRWDT instruction should be executed

by the application software only during the

last 1/4 of the WDT period. This CLRWDT

window can be determined by using a timer.

If a CLRWDT instruction is executed before

this window, a WDT Reset occurs.

All Device Resets

Transition to New Clock Source

Exit Sleep or Idle Mode

PWRSAV Instruction

CLRWDT Instruction

WDTPRE WDTPOST<3:0>

Watchdog Timer

Prescaler

(divide by N1)

Postscaler

(divide by N2)

Sleep/Idle

WDT

WDT Window Select

WINDIS

WDT

CLRWDT Instruction

SWDTEN

FWDTEN

LPRC Clock

RS RS

Wake-up

Reset

dsPIC33FJXXXGPX06A/X08A/X10A

22.5 JTAG Interface

dsPIC33FJXXXGPX06A/X08A/X10A devices imple-

ment a JTAG interface, which supports boundary scan

device testing, as well as in-circuit programming.

Detailed information on the interface will be provided in

future revisions of the document.

22.6 Code Protection and

CodeGuard™ Security

The dsPIC33F product families offer the advanced

implementation of CodeGuard™ Security. CodeGuard™

Security enables multiple parties to securely share

resources (memory, interrupts and peripherals) on a

single chip. This feature helps protect individual

Intellectual Property in collaborative system designs.

When coupled with software encryption libraries,

CodeGuard Security can be used to securely update

Flash even when multiple IP are resident on the single

chip. The code protection features vary depending on

the actual dsPIC33F implemented. The following

sections provide an overview of these features.

The code protection features are controlled by the

Configuration registers: FBS, FSS and FGS.

22.7 In-Circuit Serial Programming

dsPIC33FJXXXGPX06A/X08A/X10A family digital sig-

nal controllers can be serially programmed while in the

end application circuit. This is simply done with two

lines for clock and data and three other lines for power,

ground and the programming sequence. This allows

customers to manufacture boards with unprogrammed

devices and then program the digital signal controller

just before shipping the product. This also allows the

most recent firmware or a custom firmware, to be

programmed. Please refer to the “dsPIC33F/PIC24H

Flash Programming Specification” (DS70152)

document for details about ICSP.

Any one out of three pairs of programming clock/data

pins may be used:

• PGEC1 and PGED1

• PGEC2 and PGED2

• PGEC3 and PGED3

22.8 In-Circuit Debugger

When MPLAB® ICD 2 is selected as a debugger, the

in-circuit debugging functionality is enabled. This

function allows simple debugging functions when used

with MPLAB IDE. Debugging functionality is controlled

through the PGECx (Emulation/Debug Clock) and

PGEDx (Emulation/Debug Data) pin functions.

Any one out of three pairs of debugging clock/data pins

may be used:

• PGEC1 and PGED1

• PGEC2 and PGED2

• PGEC3 and PGED3

To use the in-circuit debugger function of the device,

the design must implement ICSP connections to

MCLR, VDD, VSS and the PGEDx/PGECx pin pair. In

addition, when the feature is enabled, some of the

resources are not available for general use. These

resources include the first 80 bytes of data RAM and

two I/O pins.

Note: Refer to Section 23. “CodeGuard™

Security” (DS70199) in the “dsPIC33F/

PIC24H Family Reference Manual” for fur-

ther information on usage, configuration

and operation of CodeGuard™ Security.

dsPIC33FJXXXGPX06A/X08A/X10A

23.0 INSTRUCTION SET SUMMARY

The dsPIC33F instruction set is identical to that of the

dsPIC30F.

Most instructions are a single program memory word

(24 bits). Only three instructions require two program

memory locations.

Each single-word instruction is a 24-bit word, divided

into an 8-bit opcode, which specifies the instruction

type and one or more operands, which further specify

the operation of the instruction.

The instruction set is highly orthogonal and is grouped

into five basic categories:

• Word or byte-oriented operations

• Bit-oriented operations

• Literal operations

• DSP operations

• Control operations

Table 23-1 illustrates the general symbols used in

describing the instructions.

The dsPIC33F instruction set summary in Ta b l e 2 3 - 2

provides all the instructions, along with the status flags

affected by each instruction.

Most word or byte-oriented W register instructions

(including barrel shift instructions) have three

operands:

• The first source operand which is typically a

• The second source operand which is typically a

• The destination of the result which is typically a

However, word or byte-oriented file register instructions

have two operands:

• The file register specified by the value ‘f’

• The destination, which could either be the file

‘WREG’

Most bit-oriented instructions (including simple rotate/

shift instructions) have two operands:

• The W register (with or without an address

modifier) or file register (specified by the value of

‘Ws’ or ‘f’)

• The bit in the W register or file register

(specified by a literal value or indirectly by the

contents of register ‘Wb’)

The literal instructions that involve data movement may

use some of the following operands:

• A literal value to be loaded into a W register or file

• The W register or file register where the literal

value is to be loaded (specified by ‘Wb’ or ‘f’)

However, literal instructions that involve arithmetic or

logical operations use some of the following operands:

• The first source operand which is a register ‘Wb’

without any address modifier

• The second source operand which is a literal

value

• The destination of the result (only if not the same

as the first source operand) which is typically a

The MAC class of DSP instructions may use some of the

following operands:

• The accumulator (A or B) to be used (required

operand)

• The W registers to be used as the two operands

• The X and Y address space prefetch operations

• The X and Y address space prefetch destinations

• The accumulator write back destination

The other DSP instructions do not involve any

multiplication and may include:

• The accumulator to be used (required)

• The source or destination operand (designated as

Wso or Wdo, respectively) with or without an

address modifier

• The amount of shift specified by a W register ‘Wn’

or a literal value

The control instructions may use some of the following

operands:

• A program memory address

• The mode of the table read and table write

instructions

Note: This data sheet summarizes the features

of the dsPIC33FJXXXGPX06A/X08A/

X10A family of devices. However, it is not

intended to be a comprehensive

reference source. To complement the

information in this data sheet, refer to the

latest family reference sections of the

“dsPIC33F/PIC24H Family Reference

Manual”, which are available from the

Microchip website (www.microchip.com).

dsPIC33FJXXXGPX06A/X08A/X10A

All instructions are a single word, except for certain

double-word instructions, which were made

double-word instructions so that all the required

information is available in these 48 bits. In the second

word, the 8 MSbs are ‘0’s. If this second word is

executed as an instruction (by itself), it will execute as

a NOP.

Most single-word instructions are executed in a single

instruction cycle, unless a conditional test is true, or the

program counter is changed as a result of the

instruction. In these cases, the execution takes two

instruction cycles with the additional instruction cycle(s)

executed as a NOP. Notable exceptions are the BRA

(unconditional/computed branch), indirect CALL/GOTO,

all table reads and writes and RETURN/RETFIE

instructions, which are single-word instructions but take

two or three cycles. Certain instructions that involve skip-

ping over the subsequent instruction require either two

or three cycles if the skip is performed, depending on

whether the instruction being skipped is a single-word or

two-word instruction. Moreover, double-word moves

require two cycles. The double-word instructions

execute in two instruction cycles.

Note: For more details on the instruction set,

refer to the “16-bit MCU and DSC

Programmer’s Reference Manual”

(DS70157).

TABLE 23-1: SYMBOLS USED IN OPCODE DESCRIPTIONS

Field Description

#text Means literal defined by “text”

(text) Means “content of text”

[text] Means “the location addressed by text”

{ } Optional field or operation

<n:m> Register bit field

.b Byte mode selection

.d Double-Word mode selection

.S Shadow register select

.w Word mode selection (default)

Acc One of two accumulators {A, B}

AWB Accumulator write back destination address register ∈ {W13, [W13]+ = 2}

bit4 4-bit bit selection field (used in word addressed instructions) ∈ {0...15}

C, DC, N, OV, Z MCU Status bits: Carry, Digit Carry, Negative, Overflow, Sticky Zero

Expr Absolute address, label or expression (resolved by the linker)

f File register address ∈ {0x0000...0x1FFF}

lit1 1-bit unsigned literal ∈ {0,1}

lit4 4-bit unsigned literal ∈ {0...15}

lit5 5-bit unsigned literal ∈ {0...31}

lit8 8-bit unsigned literal ∈ {0...255}

lit10 10-bit unsigned literal ∈ {0...255} for Byte mode, {0:1023} for Word mode

lit14 14-bit unsigned literal ∈ {0...16384}

lit16 16-bit unsigned literal ∈ {0...65535}

lit23 23-bit unsigned literal ∈ {0...8388608}; LSb must be ‘0’

None Field does not require an entry, may be blank

OA, OB, SA, SB DSP Status bits: AccA Overflow, AccB Overflow, AccA Saturate, AccB Saturate

PC Program Counter

Slit10 10-bit signed literal ∈ {-512...511}

Slit16 16-bit signed literal ∈ {-32768...32767}

Slit6 6-bit signed literal ∈ {-16...16}

Wb Base W register ∈ {W0..W15}

Wd Destination W register ∈ { Wd, [Wd], [Wd++], [Wd--], [++Wd], [--Wd] }

Wdo Destination W register ∈

{ Wnd, [Wnd], [Wnd++], [Wnd--], [++Wnd], [--Wnd], [Wnd+Wb] }

Wm,Wn Dividend, Divisor working register pair (direct addressing)

dsPIC33FJXXXGPX06A/X08A/X10A

Wm*Wm Multiplicand and Multiplier working register pair for Square instructions ∈

{W4 * W4,W5 * W5,W6 * W6,W7 * W7}

Wm*Wn Multiplicand and Multiplier working register pair for DSP instructions ∈

{W4 * W5,W4 * W6,W4 * W7,W5 * W6,W5 * W7,W6 * W7}

Wn One of 16 working registers ∈ {W0..W15}

Wnd One of 16 destination working registers ∈ {W0...W15}

Wns One of 16 source working registers ∈ {W0...W15}

WREG W0 (working register used in file register instructions)

Ws Source W register ∈ { Ws, [Ws], [Ws++], [Ws--], [++Ws], [--Ws] }

Wso Source W register ∈

{ Wns, [Wns], [Wns++], [Wns--], [++Wns], [--Wns], [Wns+Wb] }

Wx X data space prefetch address register for DSP instructions

∈{[W8]+ = 6, [W8]+ = 4, [W8]+ = 2, [W8], [W8]- = 6, [W8]- = 4, [W8]- = 2,

[W9]+ = 6, [W9]+ = 4, [W9]+ = 2, [W9], [W9]- = 6, [W9]- = 4, [W9]- = 2,

[W9 + W12], none}

Wxd X data space prefetch destination register for DSP instructions ∈ {W4...W7}

Wy Y data space prefetch address register for DSP instructions

∈{[W10]+ = 6, [W10]+ = 4, [W10]+ = 2, [W10], [W10]- = 6, [W10]- = 4, [W10]- = 2,

[W11]+ = 6, [W11]+ = 4, [W11]+ = 2, [W11], [W11]- = 6, [W11]- = 4, [W11]- = 2,

[W11 + W12], none}

Wyd Y data space prefetch destination register for DSP instructions ∈ {W4...W7}

TABLE 23-1: SYMBOLS USED IN OPCODE DESCRIPTIONS (CONTINUED)

Field Description

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 23-2: INSTRUCTION SET OVERVIEW

Base

Instr

Assembly

Mnemonic Assembly Syntax Description # of

Words

# of

Cycles

Status Flags

Affected

1ADD ADD Acc Add Accumulators 1 1 OA,OB,SA,SB

ADD f f = f + WREG 1 1 C,DC,N,OV,Z

ADD f,WREG WREG = f + WREG 1 1 C,DC,N,OV,Z

ADD #lit10,Wn Wd = lit10 + Wd 1 1 C,DC,N,OV,Z

ADD Wb,Ws,Wd Wd = Wb + Ws 1 1 C,DC,N,OV,Z

ADD Wb,#lit5,Wd Wd = Wb + lit5 1 1 C,DC,N,OV,Z

ADD Wso,#Slit4,Acc 16-bit Signed Add to Accumulator 1 1 OA,OB,SA,SB

2ADDC ADDC f f = f + WREG + (C) 1 1 C,DC,N,OV,Z

ADDC f,WREG WREG = f + WREG + (C) 1 1 C,DC,N,OV,Z

ADDC #lit10,Wn Wd = lit10 + Wd + (C) 1 1 C,DC,N,OV,Z

ADDC Wb,Ws,Wd Wd = Wb + Ws + (C) 1 1 C,DC,N,OV,Z

ADDC Wb,#lit5,Wd Wd = Wb + lit5 + (C) 1 1 C,DC,N,OV,Z

3AND AND f f = f .AND. WREG 1 1 N,Z

AND f,WREG WREG = f .AND. WREG 1 1 N,Z

AND #lit10,Wn Wd = lit10 .AND. Wd 1 1 N,Z

AND Wb,Ws,Wd Wd = Wb .AND. Ws 1 1 N,Z

AND Wb,#lit5,Wd Wd = Wb .AND. lit5 1 1 N,Z

4ASR ASR f f = Arithmetic Right Shift f 1 1 C,N,OV,Z

ASR f,WREG WREG = Arithmetic Right Shift f 1 1 C,N,OV,Z

ASR Ws,Wd Wd = Arithmetic Right Shift Ws 1 1 C,N,OV,Z

ASR Wb,Wns,Wnd Wnd = Arithmetic Right Shift Wb by Wns 1 1 N,Z

ASR Wb,#lit5,Wnd Wnd = Arithmetic Right Shift Wb by lit5 1 1 N,Z

5BCLR BCLR f,#bit4 Bit Clear f 1 1 None

BCLR Ws,#bit4 Bit Clear Ws 1 1 None

6BRA BRA C,Expr Branch if Carry 1 1 (2) None

BRA GE,Expr Branch if greater than or equal 1 1 (2) None

BRA GEU,Expr Branch if unsigned greater than or equal 1 1 (2) None

BRA GT,Expr Branch if greater than 1 1 (2) None

BRA GTU,Expr Branch if unsigned greater than 1 1 (2) None

BRA LE,Expr Branch if less than or equal 1 1 (2) None

BRA LEU,Expr Branch if unsigned less than or equal 1 1 (2) None

BRA LT,Expr Branch if less than 1 1 (2) None

BRA LTU,Expr Branch if unsigned less than 1 1 (2) None

BRA N,Expr Branch if Negative 1 1 (2) None

BRA NC,Expr Branch if Not Carry 1 1 (2) None

BRA NN,Expr Branch if Not Negative 1 1 (2) None

BRA NOV,Expr Branch if Not Overflow 1 1 (2) None

BRA NZ,Expr Branch if Not Zero 1 1 (2) None

BRA OA,Expr Branch if Accumulator A overflow 1 1 (2) None

BRA OB,Expr Branch if Accumulator B overflow 1 1 (2) None

BRA OV,Expr Branch if Overflow 1 1 (2) None

BRA SA,Expr Branch if Accumulator A saturated 1 1 (2) None

BRA SB,Expr Branch if Accumulator B saturated 1 1 (2) None

BRA Expr Branch Unconditionally 1 2 None

BRA Z,Expr Branch if Zero 1 1 (2) None

BRA Wn Computed Branch 1 2 None

7BSET BSET f,#bit4 Bit Set f 1 1 None

BSET Ws,#bit4 Bit Set Ws 1 1 None

8BSW BSW.C Ws,Wb Write C bit to Ws<Wb> 1 1 None

BSW.Z Ws,Wb Write Z bit to Ws<Wb> 1 1 None

9BTG BTG f,#bit4 Bit Toggle f 1 1 None

BTG Ws,#bit4 Bit Toggle Ws 1 1 None

dsPIC33FJXXXGPX06A/X08A/X10A

10 BTSC BTSC f,#bit4 Bit Test f, Skip if Clear 1 1

(2 or 3)

None

BTSC Ws,#bit4 Bit Test Ws, Skip if Clear 1 1

(2 or 3)

None

11 BTSS BTSS f,#bit4 Bit Test f, Skip if Set 1 1

(2 or 3)

None

BTSS Ws,#bit4 Bit Test Ws, Skip if Set 1 1

(2 or 3)

None

12 BTST BTST f,#bit4 Bit Test f 1 1 Z

BTST.C Ws,#bit4 Bit Test Ws to C 1 1 C

BTST.Z Ws,#bit4 Bit Test Ws to Z 1 1 Z

BTST.C Ws,Wb Bit Test Ws<Wb> to C 1 1 C

BTST.Z Ws,Wb Bit Test Ws<Wb> to Z 1 1 Z

13 BTSTS BTSTS f,#bit4 Bit Test then Set f 1 1 Z

BTSTS.C Ws,#bit4 Bit Test Ws to C, then Set 1 1 C

BTSTS.Z Ws,#bit4 Bit Test Ws to Z, then Set 1 1 Z

14 CALL CALL lit23 Call subroutine 2 2 None

CALL Wn Call indirect subroutine 1 2 None

15 CLR CLR f f = 0x0000 1 1 None

CLR WREG WREG = 0x0000 1 1 None

CLR Ws Ws = 0x0000 1 1 None

CLR Acc,Wx,Wxd,Wy,Wyd,AWB Clear Accumulator 1 1 OA,OB,SA,SB

16 CLRWDT CLRWDT Clear Watchdog Timer 1 1 WDTO,Sleep

17 COM COM f f = f 11 N,Z

COM f,WREG WREG = f 11 N,Z

COM Ws,Wd Wd = Ws 11 N,Z

18 CP CP f Compare f with WREG 1 1 C,DC,N,OV,Z

CP Wb,#lit5 Compare Wb with lit5 1 1 C,DC,N,OV,Z

CP Wb,Ws Compare Wb with Ws (Wb – Ws) 1 1 C,DC,N,OV,Z

19 CP0 CP0 f Compare f with 0x0000 1 1 C,DC,N,OV,Z

CP0 Ws Compare Ws with 0x0000 1 1 C,DC,N,OV,Z

20 CPB CPB f Compare f with WREG, with Borrow 1 1 C,DC,N,OV,Z

CPB Wb,#lit5 Compare Wb with lit5, with Borrow 1 1 C,DC,N,OV,Z

CPB Wb,Ws Compare Wb with Ws, with Borrow

(Wb - Ws - C)

1 1 C,DC,N,OV,Z

21 CPSEQ CPSEQ Wb, Wn Compare Wb with Wn, skip if = 1 1

(2 or 3)

None

22 CPSGT CPSGT Wb, Wn Compare Wb with Wn, skip if > 1 1

(2 or 3)

None

23 CPSLT CPSLT Wb, Wn Compare Wb with Wn, skip if < 1 1

(2 or 3)

None

24 CPSNE CPSNE Wb, Wn Compare Wb with Wn, skip if ≠11

(2 or 3)

None

25 DAW DAW Wn Wn = decimal adjust Wn 1 1 C

26 DEC DEC f f = f – 1 1 1 C,DC,N,OV,Z

DEC f,WREG WREG = f – 1 1 1 C,DC,N,OV,Z

DEC Ws,Wd Wd = Ws – 1 1 1 C,DC,N,OV,Z

27 DEC2 DEC2 f f = f – 2 1 1 C,DC,N,OV,Z

DEC2 f,WREG WREG = f – 2 1 1 C,DC,N,OV,Z

DEC2 Ws,Wd Wd = Ws – 2 1 1 C,DC,N,OV,Z

28 DISI DISI #lit14 Disable Interrupts for k instruction cycles 1 1 None

TABLE 23-2: INSTRUCTION SET OVERVIEW (CONTINUED)

Base

Instr

Assembly

Mnemonic Assembly Syntax Description # of

Words

# of

Cycles

Status Flags

Affected

dsPIC33FJXXXGPX06A/X08A/X10A

29 DIV DIV.S Wm,Wn Signed 16/16-bit Integer Divide 1 18 N,Z,C,OV

DIV.SD Wm,Wn Signed 32/16-bit Integer Divide 1 18 N,Z,C,OV

DIV.U Wm,Wn Unsigned 16/16-bit Integer Divide 1 18 N,Z,C,OV

DIV.UD Wm,Wn Unsigned 32/16-bit Integer Divide 1 18 N,Z,C,OV

30 DIVF DIVF Wm,Wn Signed 16/16-bit Fractional Divide 1 18 N,Z,C,OV

31 DO DO #lit14,Expr Do code to PC + Expr, lit14 + 1 times 2 2 None

DO Wn,Expr Do code to PC + Expr, (Wn) + 1 times 2 2 None

32 ED ED Wm*Wm,Acc,Wx,Wy,Wxd Euclidean Distance (no accumulate) 1 1 OA,OB,OAB,

SA,SB,SAB

33 EDAC EDAC Wm*Wm,Acc,Wx,Wy,Wxd Euclidean Distance 1 1 OA,OB,OAB,

SA,SB,SAB

34 EXCH EXCH Wns,Wnd Swap Wns with Wnd 1 1 None

35 FBCL FBCL Ws,Wnd Find Bit Change from Left (MSb) Side 1 1 C

36 FF1L FF1L Ws,Wnd Find First One from Left (MSb) Side 1 1 C

37 FF1R FF1R Ws,Wnd Find First One from Right (LSb) Side 1 1 C

38 GOTO GOTO Expr Go to address 2 2 None

GOTO Wn Go to indirect 1 2 None

39 INC INC f f = f + 1 1 1 C,DC,N,OV,Z

INC f,WREG WREG = f + 1 1 1 C,DC,N,OV,Z

INC Ws,Wd Wd = Ws + 1 1 1 C,DC,N,OV,Z

40 INC2 INC2 f f = f + 2 1 1 C,DC,N,OV,Z

INC2 f,WREG WREG = f + 2 1 1 C,DC,N,OV,Z

INC2 Ws,Wd Wd = Ws + 2 1 1 C,DC,N,OV,Z

41 IOR IOR f f = f .IOR. WREG 1 1 N,Z

IOR f,WREG WREG = f .IOR. WREG 1 1 N,Z

IOR #lit10,Wn Wd = lit10 .IOR. Wd 1 1 N,Z

IOR Wb,Ws,Wd Wd = Wb .IOR. Ws 1 1 N,Z

IOR Wb,#lit5,Wd Wd = Wb .IOR. lit5 1 1 N,Z

42 LAC LAC Wso,#Slit4,Acc Load Accumulator 1 1 OA,OB,OAB,

SA,SB,SAB

43 LNK LNK #lit14 Link Frame Pointer 1 1 None

44 LSR LSR f f = Logical Right Shift f 1 1 C,N,OV,Z

LSR f,WREG WREG = Logical Right Shift f 1 1 C,N,OV,Z

LSR Ws,Wd Wd = Logical Right Shift Ws 1 1 C,N,OV,Z

LSR Wb,Wns,Wnd Wnd = Logical Right Shift Wb by Wns 1 1 N,Z

LSR Wb,#lit5,Wnd Wnd = Logical Right Shift Wb by lit5 1 1 N,Z

45 MAC MAC Wm*Wn,Acc,Wx,Wxd,Wy,Wyd

AWB

Multiply and Accumulate 1 1 OA,OB,OAB,

SA,SB,SAB

MAC Wm*Wm,Acc,Wx,Wxd,Wy,Wyd Square and Accumulate 1 1 OA,OB,OAB,

SA,SB,SAB

46 MOV MOV f,Wn Move f to Wn 1 1 None

MOV f Move f to f 1 1 None

MOV f,WREG Move f to WREG 1 1 N,Z

MOV #lit16,Wn Move 16-bit literal to Wn 1 1 None

MOV.b #lit8,Wn Move 8-bit literal to Wn 1 1 None

MOV Wn,f Move Wn to f 1 1 None

MOV Wso,Wdo Move Ws to Wd 1 1 None

MOV WREG,f Move WREG to f 1 1 None

MOV.D Wns,Wd Move Double from W(ns):W(ns + 1) to Wd 1 2 None

MOV.D Ws,Wnd Move Double from Ws to W(nd + 1):W(nd) 1 2 None

47 MOVSAC MOVSAC Acc,Wx,Wxd,Wy,Wyd,AWB Prefetch and store accumulator 1 1 None

TABLE 23-2: INSTRUCTION SET OVERVIEW (CONTINUED)

Base

Instr

Assembly

Mnemonic Assembly Syntax Description # of

Words

# of

Cycles

Status Flags

Affected

dsPIC33FJXXXGPX06A/X08A/X10A

48 MPY MPY

Wm*Wn,Acc,Wx,Wxd,Wy,Wyd

Multiply Wm by Wn to Accumulator 1 1 OA,OB,OAB,

SA,SB,SAB

MPY

Wm*Wm,Acc,Wx,Wxd,Wy,Wyd

Square Wm to Accumulator 1 1 OA,OB,OAB,

SA,SB,SAB

49 MPY.N MPY.N

Wm*Wn,Acc,Wx,Wxd,Wy,Wyd

-(Multiply Wm by Wn) to Accumulator 1 1 None

50 MSC MSC Wm*Wm,Acc,Wx,Wxd,Wy,Wyd

AWB

Multiply and Subtract from Accumulator 1 1 OA,OB,OAB,

SA,SB,SAB

51 MUL MUL.SS Wb,Ws,Wnd {Wnd + 1, Wnd} = signed(Wb) * signed(Ws) 1 1 None

MUL.SU Wb,Ws,Wnd {Wnd + 1, Wnd} = signed(Wb) * unsigned(Ws) 1 1 None

MUL.US Wb,Ws,Wnd {Wnd + 1, Wnd} = unsigned(Wb) * signed(Ws) 1 1 None

MUL.UU Wb,Ws,Wnd {Wnd + 1, Wnd} = unsigned(Wb) *

unsigned(Ws)

1 1 None

MUL.SU Wb,#lit5,Wnd {Wnd + 1, Wnd} = signed(Wb) * unsigned(lit5) 1 1 None

MUL.UU Wb,#lit5,Wnd {Wnd + 1, Wnd} = unsigned(Wb) *

unsigned(lit5)

1 1 None

MUL f W3:W2 = f * WREG 1 1 None

52 NEG NEG Acc Negate Accumulator 1 1 OA,OB,OAB,

SA,SB,SAB

NEG f f = f + 1 1 1 C,DC,N,OV,Z

NEG f,WREG WREG = f + 1 1 1 C,DC,N,OV,Z

NEG Ws,Wd Wd = Ws + 1 1 1 C,DC,N,OV,Z

53 NOP NOP No Operation 1 1 None

NOPR No Operation 1 1 None

54 POP POP f Pop f from Top-of-Stack (TOS) 1 1 None

POP Wdo Pop from Top-of-Stack (TOS) to Wdo 1 1 None

POP.D Wnd Pop from Top-of-Stack (TOS) to

W(nd):W(nd + 1)

1 2 None

POP.S Pop Shadow Registers 1 1 All

55 PUSH PUSH f Push f to Top-of-Stack (TOS) 1 1 None

PUSH Wso Push Wso to Top-of-Stack (TOS) 1 1 None

PUSH.D Wns Push W(ns):W(ns + 1) to Top-of-Stack (TOS) 1 2 None

PUSH.S Push Shadow Registers 1 1 None

56 PWRSAV PWRSAV #lit1 Go into Sleep or Idle mode 1 1 WDTO,Sleep

57 RCALL RCALL Expr Relative Call 1 2 None

RCALL Wn Computed Call 1 2 None

58 REPEAT REPEAT #lit14 Repeat Next Instruction lit14 + 1 times 1 1 None

REPEAT Wn Repeat Next Instruction (Wn) + 1 times 1 1 None

59 RESET RESET Software device Reset 1 1 None

60 RETFIE RETFIE Return from interrupt 1 3 (2) None

61 RETLW RETLW #lit10,Wn Return with literal in Wn 1 3 (2) None

62 RETURN RETURN Return from Subroutine 1 3 (2) None

63 RLC RLC f f = Rotate Left through Carry f 1 1 C,N,Z

RLC f,WREG WREG = Rotate Left through Carry f 1 1 C,N,Z

RLC Ws,Wd Wd = Rotate Left through Carry Ws 1 1 C,N,Z

64 RLNC RLNC f f = Rotate Left (No Carry) f 1 1 N,Z

RLNC f,WREG WREG = Rotate Left (No Carry) f 1 1 N,Z

RLNC Ws,Wd Wd = Rotate Left (No Carry) Ws 1 1 N,Z

65 RRC RRC f f = Rotate Right through Carry f 1 1 C,N,Z

RRC f,WREG WREG = Rotate Right through Carry f 1 1 C,N,Z

RRC Ws,Wd Wd = Rotate Right through Carry Ws 1 1 C,N,Z

TABLE 23-2: INSTRUCTION SET OVERVIEW (CONTINUED)

Base

Instr

Assembly

Mnemonic Assembly Syntax Description # of

Words

# of

Cycles

Status Flags

Affected

dsPIC33FJXXXGPX06A/X08A/X10A

66 RRNC RRNC f f = Rotate Right (No Carry) f 1 1 N,Z

RRNC f,WREG WREG = Rotate Right (No Carry) f 1 1 N,Z

RRNC Ws,Wd Wd = Rotate Right (No Carry) Ws 1 1 N,Z

67 SAC SAC Acc,#Slit4,Wdo Store Accumulator 1 1 None

SAC.R Acc,#Slit4,Wdo Store Rounded Accumulator 1 1 None

68 SE SE Ws,Wnd Wnd = sign-extended Ws 1 1 C,N,Z

69 SETM SETM f f = 0xFFFF 1 1 None

SETM WREG WREG = 0xFFFF 1 1 None

SETM Ws Ws = 0xFFFF 1 1 None

70 SFTAC SFTAC Acc,Wn Arithmetic Shift Accumulator by (Wn) 1 1 OA,OB,OAB,

SA,SB,SAB

SFTAC Acc,#Slit6 Arithmetic Shift Accumulator by Slit6 1 1 OA,OB,OAB,

SA,SB,SAB

71 SL SL f f = Left Shift f 1 1 C,N,OV,Z

SL f,WREG WREG = Left Shift f 1 1 C,N,OV,Z

SL Ws,Wd Wd = Left Shift Ws 1 1 C,N,OV,Z

SL Wb,Wns,Wnd Wnd = Left Shift Wb by Wns 1 1 N,Z

SL Wb,#lit5,Wnd Wnd = Left Shift Wb by lit5 1 1 N,Z

72 SUB SUB Acc Subtract Accumulators 1 1 OA,OB,OAB,

SA,SB,SAB

SUB f f = f – WREG 1 1 C,DC,N,OV,Z

SUB f,WREG WREG = f – WREG 1 1 C,DC,N,OV,Z

SUB #lit10,Wn Wn = Wn – lit10 1 1 C,DC,N,OV,Z

SUB Wb,Ws,Wd Wd = Wb – Ws 1 1 C,DC,N,OV,Z

SUB Wb,#lit5,Wd Wd = Wb – lit5 1 1 C,DC,N,OV,Z

73 SUBB SUBB f f = f – WREG – (C) 1 1 C,DC,N,OV,Z

SUBB f,WREG WREG = f – WREG – (C) 1 1 C,DC,N,OV,Z

SUBB #lit10,Wn Wn = Wn – lit10 – (C) 1 1 C,DC,N,OV,Z

SUBB Wb,Ws,Wd Wd = Wb – Ws – (C) 1 1 C,DC,N,OV,Z

SUBB Wb,#lit5,Wd Wd = Wb – lit5 – (C) 1 1 C,DC,N,OV,Z

74 SUBR SUBR f f = WREG – f 1 1 C,DC,N,OV,Z

SUBR f,WREG WREG = WREG – f 1 1 C,DC,N,OV,Z

SUBR Wb,Ws,Wd Wd = Ws – Wb 1 1 C,DC,N,OV,Z

SUBR Wb,#lit5,Wd Wd = lit5 – Wb 1 1 C,DC,N,OV,Z

75 SUBBR SUBBR f f = WREG – f – (C) 1 1 C,DC,N,OV,Z

SUBBR f,WREG WREG = WREG – f – (C) 1 1 C,DC,N,OV,Z

SUBBR Wb,Ws,Wd Wd = Ws – Wb – (C) 1 1 C,DC,N,OV,Z

SUBBR Wb,#lit5,Wd Wd = lit5 – Wb – (C) 1 1 C,DC,N,OV,Z

76 SWAP SWAP.b Wn Wn = nibble swap Wn 1 1 None

SWAP Wn Wn = byte swap Wn 1 1 None

77 TBLRDH TBLRDH Ws,Wd Read Prog<23:16> to Wd<7:0> 1 2 None

78 TBLRDL TBLRDL Ws,Wd Read Prog<15:0> to Wd 1 2 None

79 TBLWTH TBLWTH Ws,Wd Write Ws<7:0> to Prog<23:16> 1 2 None

80 TBLWTL TBLWTL Ws,Wd Write Ws to Prog<15:0> 1 2 None

81 ULNK ULNK Unlink Frame Pointer 1 1 None

82 XOR XOR f f = f .XOR. WREG 1 1 N,Z

XOR f,WREG WREG = f .XOR. WREG 1 1 N,Z

XOR #lit10,Wn Wd = lit10 .XOR. Wd 1 1 N,Z

XOR Wb,Ws,Wd Wd = Wb .XOR. Ws 1 1 N,Z

XOR Wb,#lit5,Wd Wd = Wb .XOR. lit5 1 1 N,Z

83 ZE ZE Ws,Wnd Wnd = Zero-extend Ws 1 1 C,Z,N

TABLE 23-2: INSTRUCTION SET OVERVIEW (CONTINUED)

Base

Instr

Assembly

Mnemonic Assembly Syntax Description # of

Words

# of

Cycles

Status Flags

Affected

dsPIC33FJXXXGPX06A/X08A/X10A

24.0 DEVELOPMENT SUPPORT

The PIC® microcontrollers and dsPIC® digital signal

controllers are supported with a full range of software

and hardware development tools:

• Integrated Development Environment

- MPLAB® IDE Software

• Compilers/Assemblers/Linkers

- MPLAB C Compiler for Various Device

Families

- HI-TECH C for Various Device Families

- MPASMTM Assembler

-MPLINK

TM Object Linker/

MPLIBTM Object Librarian

- MPLAB Assembler/Linker/Librarian for

Various Device Families

• Simulators

- MPLAB SIM Software Simulator

• Emulators

- MPLAB REAL ICE™ In-Circuit Emulator

• In-Circuit Debuggers

- MPLAB ICD 3

- PICkit™ 3 Debug Express

• Device Programmers

- PICkit™ 2 Programmer

- MPLAB PM3 Device Programmer

• Low-Cost Demonstration/Development Boards,

Evaluation Kits, and Starter Kits

24.1 MPLAB Integrated Development

Environment Software

The MPLAB IDE software brings an ease of software

development previously unseen in the 8/16/32-bit

microcontroller market. The MPLAB IDE is a Windows®

operating system-based application that contains:

• A single graphical interface to all debugging tools

- Simulator

- Programmer (sold separately)

- In-Circuit Emulator (sold separately)

- In-Circuit Debugger (sold separately)

• A full-featured editor with color-coded context

• A multiple project manager

• Customizable data windows with direct edit of

contents

• High-level source code debugging

• Mouse over variable inspection

• Drag and drop variables from source to watch

windows

• Extensive on-line help

• Integration of select third party tools, such as

IAR C Compilers

The MPLAB IDE allows you to:

• Edit your source files (either C or assembly)

• One-touch compile or assemble, and download to

emulator and simulator tools (automatically

updates all project information)

• Debug using:

- Source files (C or assembly)

- Mixed C and assembly

- Machine code

MPLAB IDE supports multiple debugging tools in a

single development paradigm, from the cost-effective

simulators, through low-cost in-circuit debuggers, to

full-featured emulators. This eliminates the learning

curve when upgrading to tools with increased flexibility

and power.

dsPIC33FJXXXGPX06A/X08A/X10A

24.2 MPLAB C Compilers for Various

Device Families

The MPLAB C Compiler code development systems

are complete ANSI C compilers for Microchip’s PIC18,

PIC24 and PIC32 families of microcontrollers and the

dsPIC30 and dsPIC33 families of digital signal control-

lers. These compilers provide powerful integration

capabilities, superior code optimization and ease of

use.

For easy source level debugging, the compilers provide

symbol information that is optimized to the MPLAB IDE

debugger.

24.3 HI-TECH C for Various Device

Families

The HI-TECH C Compiler code development systems

are complete ANSI C compilers for Microchip’s PIC

family of microcontrollers and the dsPIC family of digital

signal controllers. These compilers provide powerful

integration capabilities, omniscient code generation

and ease of use.

For easy source level debugging, the compilers provide

symbol information that is optimized to the MPLAB IDE

debugger.

The compilers include a macro assembler, linker, pre-

processor, and one-step driver, and can run on multiple

platforms.

24.4 MPASM Assembler

The MPASM Assembler is a full-featured, universal

macro assembler for PIC10/12/16/18 MCUs.

The MPASM Assembler generates relocatable object

files for the MPLINK Object Linker, Intel® standard HEX

files, MAP files to detail memory usage and symbol

reference, absolute LST files that contain source lines

and generated machine code and COFF files for

debugging.

The MPASM Assembler features include:

• Integration into MPLAB IDE projects

• User-defined macros to streamline

assembly code

• Conditional assembly for multi-purpose

source files

• Directives that allow complete control over the

assembly process

24.5 MPLINK Object Linker/

MPLIB Object Librarian

The MPLINK Object Linker combines relocatable

objects created by the MPASM Assembler and the

MPLAB C18 C Compiler. It can link relocatable objects

from precompiled libraries, using directives from a

linker script.

The MPLIB Object Librarian manages the creation and

modification of library files of precompiled code. When

a routine from a library is called from a source file, only

the modules that contain that routine will be linked in

with the application. This allows large libraries to be

used efficiently in many different applications.

The object linker/library features include:

• Efficient linking of single libraries instead of many

smaller files

• Enhanced code maintainability by grouping

related modules together

• Flexible creation of libraries with easy module

listing, replacement, deletion and extraction

24.6 MPLAB Assembler, Linker and

Librarian for Various Device

Families

MPLAB Assembler produces relocatable machine

code from symbolic assembly language for PIC24,

PIC32 and dsPIC devices. MPLAB C Compiler uses

the assembler to produce its object file. The assembler

generates relocatable object files that can then be

archived or linked with other relocatable object files and

archives to create an executable file. Notable features

of the assembler include:

• Support for the entire device instruction set

• Support for fixed-point and floating-point data

• Command line interface

• Rich directive set

• Flexible macro language

• MPLAB IDE compatibility

dsPIC33FJXXXGPX06A/X08A/X10A

24.7 MPLAB SIM Software Simulator

The MPLAB SIM Software Simulator allows code

development in a PC-hosted environment by simulat-

ing the PIC MCUs and dsPIC® DSCs on an instruction

level. On any given instruction, the data areas can be

examined or modified and stimuli can be applied from

a comprehensive stimulus controller. Registers can be

logged to files for further run-time analysis. The trace

buffer and logic analyzer display extend the power of

the simulator to record and track program execution,

actions on I/O, most peripherals and internal registers.

The MPLAB SIM Software Simulator fully supports

symbolic debugging using the MPLAB C Compilers,

and the MPASM and MPLAB Assemblers. The soft-

ware simulator offers the flexibility to develop and

debug code outside of the hardware laboratory envi-

ronment, making it an excellent, economical software

development tool.

24.8 MPLAB REAL ICE In-Circuit

Emulator System

MPLAB REAL ICE In-Circuit Emulator System is

Microchip’s next generation high-speed emulator for

Microchip Flash DSC and MCU devices. It debugs and

programs PIC® Flash MCUs and dsPIC® Flash DSCs

with the easy-to-use, powerful graphical user interface of

the MPLAB Integrated Development Environment (IDE),

included with each kit.

The emulator is connected to the design engineer’s PC

using a high-speed USB 2.0 interface and is connected

to the target with either a connector compatible with in-

circuit debugger systems (RJ11) or with the new high-

speed, noise tolerant, Low-Voltage Differential Signal

(LVDS) interconnection (CAT5).

The emulator is field upgradable through future firmware

downloads in MPLAB IDE. In upcoming releases of

MPLAB IDE, new devices will be supported, and new

features will be added. MPLAB REAL ICE offers

significant advantages over competitive emulators

including low-cost, full-speed emulation, run-time

variable watches, trace analysis, complex breakpoints, a

ruggedized probe interface and long (up to three meters)

interconnection cables.

24.9 MPLAB ICD 3 In-Circuit Debugger

System

MPLAB ICD 3 In-Circuit Debugger System is Micro-

chip's most cost effective high-speed hardware

debugger/programmer for Microchip Flash Digital Sig-

nal Controller (DSC) and microcontroller (MCU)

devices. It debugs and programs PIC® Flash microcon-

trollers and dsPIC® DSCs with the powerful, yet easy-

to-use graphical user interface of MPLAB Integrated

Development Environment (IDE).

The MPLAB ICD 3 In-Circuit Debugger probe is con-

nected to the design engineer's PC using a high-speed

USB 2.0 interface and is connected to the target with a

connector compatible with the MPLAB ICD 2 or MPLAB

REAL ICE systems (RJ-11). MPLAB ICD 3 supports all

MPLAB ICD 2 headers.

24.10 PICkit 3 In-Circuit Debugger/

Programmer and

PICkit 3 Debug Express

The MPLAB PICkit 3 allows debugging and program-

ming of PIC® and dsPIC® Flash microcontrollers at a

most affordable price point using the powerful graphical

user interface of the MPLAB Integrated Development

Environment (IDE). The MPLAB PICkit 3 is connected

to the design engineer's PC using a full speed USB

interface and can be connected to the target via an

Microchip debug (RJ-11) connector (compatible with

MPLAB ICD 3 and MPLAB REAL ICE). The connector

uses two device I/O pins and the reset line to imple-

ment in-circuit debugging and In-Circuit Serial Pro-

gramming™.

The PICkit 3 Debug Express include the PICkit 3, demo

board and microcontroller, hookup cables and CDROM

with user’s guide, lessons, tutorial, compiler and

MPLAB IDE software.

dsPIC33FJXXXGPX06A/X08A/X10A

24.11 PICkit 2 Development

Programmer/Debugger and

PICkit 2 Debug Express

The PICkit™ 2 Development Programmer/Debugger is

a low-cost development tool with an easy to use inter-

face for programming and debugging Microchip’s Flash

families of microcontrollers. The full featured

Windows® programming interface supports baseline

(PIC10F, PIC12F5xx, PIC16F5xx), midrange

(PIC12F6xx, PIC16F), PIC18F, PIC24, dsPIC30,

dsPIC33, and PIC32 families of 8-bit, 16-bit, and 32-bit

microcontrollers, and many Microchip Serial EEPROM

products. With Microchip’s powerful MPLAB Integrated

Development Environment (IDE) the PICkit™ 2

enables in-circuit debugging on most PIC® microcon-

trollers. In-Circuit-Debugging runs, halts and single

steps the program while the PIC microcontroller is

embedded in the application. When halted at a break-

point, the file registers can be examined and modified.

The PICkit 2 Debug Express include the PICkit 2, demo

board and microcontroller, hookup cables and CDROM

with user’s guide, lessons, tutorial, compiler and

MPLAB IDE software.

24.12 MPLAB PM3 Device Programmer

The MPLAB PM3 Device Programmer is a universal,

CE compliant device programmer with programmable

voltage verification at VDDMIN and VDDMAX for

maximum reliability. It features a large LCD display

(128 x 64) for menus and error messages and a modu-

lar, detachable socket assembly to support various

package types. The ICSP™ cable assembly is included

as a standard item. In Stand-Alone mode, the MPLAB

PM3 Device Programmer can read, verify and program

PIC devices without a PC connection. It can also set

code protection in this mode. The MPLAB PM3

connects to the host PC via an RS-232 or USB cable.

The MPLAB PM3 has high-speed communications and

optimized algorithms for quick programming of large

memory devices and incorporates an MMC card for file

storage and data applications.

24.13 Demonstration/Development

Boards, Evaluation Kits, and

Starter Kits

A wide variety of demonstration, development and

evaluation boards for various PIC MCUs and dsPIC

DSCs allows quick application development on fully func-

tional systems. Most boards include prototyping areas for

adding custom circuitry and provide application firmware

and source code for examination and modification.

The boards support a variety of features, including LEDs,

temperature sensors, switches, speakers, RS-232

interfaces, LCD displays, potentiometers and additional

EEPROM memory.

The demonstration and development boards can be

used in teaching environments, for prototyping custom

circuits and for learning about various microcontroller

applications.

In addition to the PICDEM™ and dsPICDEM™ demon-

stration/development board series of circuits, Microchip

has a line of evaluation kits and demonstration software

for analog filter design, KEELOQ® security ICs, CAN,

IrDA®, PowerSmart battery management, SEEVAL®

evaluation system, Sigma-Delta ADC, flow rate

sensing, plus many more.

Also available are starter kits that contain everything

needed to experience the specified device. This usually

includes a single application and debug capability, all

on one board.

Check the Microchip web page (www.microchip.com)

for the complete list of demonstration, development

and evaluation kits.

dsPIC33FJXXXGPX06A/X08A/X10A

25.0 ELECTRICAL CHARACTERISTICS

This section provides an overview of dsPIC33FJXXXGPX06A/X08A/X10A electrical characteristics. Additional informa-

tion will be provided in future revisions of this document as it becomes available.

Absolute maximum ratings for the dsPIC33FJXXXGPX06A/X08A/X10A family are listed below. Exposure to these max-

imum rating conditions for extended periods may affect device reliability. Functional operation of the device at these or

any other conditions above the parameters indicated in the operation listings of this specification is not implied.

Absolute Maximum Ratings(1)

Ambient temperature under bias.............................................................................................................-40°C to +125°C

Storage temperature .............................................................................................................................. -65°C to +160°C

Voltage on VDD with respect to VSS ......................................................................................................... -0.3V to +4.0V

Voltage on any pin that is not 5V tolerant with respect to VSS(4) .................................................... -0.3V to (VDD + 0.3V)

Voltage on any 5V tolerant pin with respect to VSS when VDD ≥ 3.0V(4) .................................................. -0.3V to +5.6V

Voltage on any 5V tolerant pin with respect to Vss when VDD < 3.0V(4)...................................................... -0.3V to 3.6V

Voltage on VCAP with respect to VSS ...................................................................................................... 2.25V to 2.75V

Maximum current out of VSS pin ...........................................................................................................................300 mA

Maximum current into VDD pin(2)...........................................................................................................................250 mA

Maximum output current sunk by any I/O pin(3) ........................................................................................................4 mA

Maximum output current sourced by any I/O pin(3)...................................................................................................4 mA

Maximum current sunk by all ports .......................................................................................................................200 mA

Maximum current sourced by all ports(2)...............................................................................................................200 mA

Note 1: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the

device. This is a stress rating only and functional operation of the device at those or any other conditions

above those indicated in the operation listings of this specification is not implied. Exposure to maximum

rating conditions for extended periods may affect device reliability.

2: Maximum allowable current is a function of device maximum power dissipation (see Table 25-2).

3: Exceptions are CLKOUT, which is able to sink/source 25 mA, and the VREF+, VREF-, SCLx, SDAx, PGECx

and PGEDx pins, which are able to sink/source 12 mA.

4: See the “Pin Diagrams” section for 5V tolerant pins.

dsPIC33FJXXXGPX06A/X08A/X10A

25.1 DC Characteristics

TABLE 25-1: OPERATING MIPS VS. VOLTAGE

Characteristic VDD Range

(in Volts)

Temp Range

(in °C)

Max MIPS

dsPIC33FJXXXGPX06A/X08A/X10A

DC5 3.0-3.6V -40°C to +85°C 40

3.0-3.6V -40°C to +125°C 40

TABLE 25-2: THERMAL OPERATING CONDITIONS

Rating Symbol Min Typ Max Unit

dsPIC33FJXXXGPX06A/X08A/X10A

Operating Junction Temperature Range TJ-40 — +125 °C

Operating Ambient Temperature Range TA-40 — +85 °C

Extended Temperature Devices

Operating Junction Temperature Range TJ-40 — +150 °C

Operating Ambient Temperature Range TA-40 — +125 °C

Power Dissipation:

Internal chip power dissipation:

PINT = VDD x (IDD - Σ IOH) PDPINT + PI/OW

I/O Pin Power Dissipation:

I/O = Σ ({VDD - VOH} x IOH) + Σ (VOL x IOL)

Maximum Allowed Power Dissipation PDMAX (TJ - TA)/θJA W

TABLE 25-3: THERMAL PACKAGING CHARACTERISTICS

Characteristic Symbol Typ Max Unit Notes

Package Thermal Resistance, 100-pin TQFP (14x14x1 mm) θJA 40 — °C/W 1

Package Thermal Resistance, 100-pin TQFP (12x12x1 mm) θJA 40 — °C/W 1

Package Thermal Resistance, 80-pin TQFP (12x12x1 mm) θJA 40 — °C/W 1

Package Thermal Resistance, 64-pin TQFP (10x10x1 mm) θJA 40 — °C/W 1

Package Thermal Resistance, 64-pin QFN (9x9x0.9 mm) θJA 28 — °C/W 1

Note 1: Junction to ambient thermal resistance, Theta-JA (θJA) numbers are achieved by package simulations.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-4: DC TEMPERATURE AND VOLTAGE SPECIFICATIONS

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic Min Typ(1) Max Units Conditions

Operating Voltage

DC10 Supply Voltage

VDD —3.0—3.6V—

DC12 VDR RAM Data Retention Voltage(2) 1.8 — — V —

DC16 VPOR VDD Start Voltage

to ensure internal

Power-on Reset signal

——VSS V—

DC17 SVDD VDD Rise Rate

to ensure internal

Power-on Reset signal

0.03 — — V/ms 0-3.0V in 0.1s

DC18 VCORE VDD Core(3)

Internal regulator voltage

2.25 — 2.75 V Voltage is dependent on

load, temperature and

VDD

Note 1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.

2: This is the limit to which VDD can be lowered without losing RAM data.

3: These parameters are characterized but not tested in manufacturing.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-5: DC CHARACTERISTICS: OPERATING CURRENT (IDD)

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Parameter

No. Typical(1) Max Units Conditions

Operating Current (IDD)(2)

DC20d 27 30 mA -40°C

3.3V 10 MIPS

DC20a 27 30 mA +25°C

DC20b 27 30 mA +85°C

DC20c 27 35 mA +125°C

DC21d 36 40 mA -40°C

3.3V 16 MIPS

DC21a 37 40 mA +25°C

DC21b 38 45 mA +85°C

DC21c 39 45 mA +125°C

DC22d 43 50 mA -40°C

3.3V 20 MIPS

DC22a 46 50 mA +25°C

DC22b 46 55 mA +85°C

DC22c 47 55 mA +125°C

DC23d 65 70 mA -40°C

3.3V 30 MIPS

DC23a 65 70 mA +25°C

DC23b 65 70 mA +85°C

DC23c 65 70 mA +125°C

DC24d 84 90 mA -40°C

3.3V 40 MIPS

DC24a 84 90 mA +25°C

DC24b 84 90 mA +85°C

DC24c 84 90 mA +125°C

Note 1: Data in “Typical” column is at 3.3V, 25°C unless otherwise stated.

2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O

pin loading and switching rate, oscillator type, internal code execution pattern and temperature, also have

an impact on the current consumption. The test conditions for all IDD measurements are as follows: OSC1

driven with external square wave from rail to rail. All I/O pins are configured as inputs and pulled to VSS.

MCLR = VDD, WDT and FSCM are disabled. CPU, SRAM, program memory and data memory are

operational. No peripheral modules are operating; however, every peripheral is being clocked (PMD bits

are all zeroed).

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-6: DC CHARACTERISTICS: IDLE CURRENT (IIDLE)

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Parameter

No. Typical(1) Max Units Conditions

Idle Current (IIDLE): Core OFF Clock ON Base Current(2)

DC40d 3 25 mA -40°C

3.3V 10 MIPS

DC40a 3 25 mA +25°C

DC40b 3 25 mA +85°C

DC40c 3 25 mA +125°C

DC41d 4 25 mA -40°C

3.3V 16 MIPS

DC41a 5 25 mA +25°C

DC41b 6 25 mA +85°C

DC41c 6 25 mA +125°C

DC42d 8 25 mA -40°C

3.3V 20 MIPS

DC42a 9 25 mA +25°C

DC42b 10 25 mA +85°C

DC42c 10 25 mA +125°C

DC43a 15 25 mA +25°C

3.3V 30 MIPS

25DC43d 15 mA -40°C

DC43b 15 25 mA +85°C

DC43c 15 25 mA +125°C

DC44d 16 25 mA -40°C

3.3V 40 MIPS

DC44a 16 25 mA +25°C

DC44b 16 25 mA +85°C

DC44c 16 25 mA +125°C

Note 1: Data in “Typical” column is at 3.3V, 25°C unless otherwise stated.

2: Base IIDLE current is measured with core off, clock on and all modules turned off. Peripheral Module

Disable SFR registers are zeroed. All I/O pins are configured as inputs and pulled to VSS.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-7: DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD)

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Parameter

No. Typical(1) Max Units Conditions

Power-Down Current (IPD)(2)

DC60d 50 200 μA -40°C

3.3V Base Power-Down Current(3)

DC60a 50 200 μA +25°C

DC60b 200 500 μA +85°C

DC60c 600 1000 μA +125°C

DC61d 8 13 μA -40°C

3.3V Watchdog Timer Current: ΔIWDT(3)

DC61a 10 15 μA +25°C

DC61b 12 20 μA +85°C

DC61c 13 25 μA +125°C

Note 1: Data in the Typical column is at 3.3V, 25°C unless otherwise stated.

2: Base IPD is measured with all peripherals and clocks shut down. All I/Os are configured as inputs and

pulled to VSS. WDT, etc., are all switched off.

3: The Δ current is the additional current consumed when the module is enabled. This current should be

added to the base IPD current.

TABLE 25-8: DC CHARACTERISTICS: DOZE CURRENT (IDOZE)

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Parameter

No. Typical(1) Max Doze Ratio Units Conditions

DC73a 11 35 1:2 mA

-40°C 3.3V 40 MIPSDC73f 11 30 1:64 mA

DC73g 11 30 1:128 mA

DC70a 42 50 1:2 mA

+25°C 3.3V 40 MIPSDC70f 26 30 1:64 mA

DC70g 25 30 1:128 mA

DC71a 41 50 1:2 mA

+85°C 3.3V 40 MIPSDC71f 25 30 1:64 mA

DC71g 24 30 1:128 mA

DC72a 42 50 1:2 mA

+125°C 3.3V 40 MIPSDC72f 26 30 1:64 mA

DC72g 25 30 1:128 mA

Note 1: Data in the Typical column is at 3.3V, 25°C unless otherwise stated.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-9: DC CHARACTERISTICS: I/O PIN INPUT SPECIFICATIONS

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA≤ +85°C for Industrial

-40°C ≤ TA≤+125°C for Extended

Param

No. Symbol Characteristic Min Typ(1) Max Units Conditions

VIL Input Low Voltage

DI10 I/O pins VSS —0.2VDD V

DI15 MCLR VSS —0.2VDD V

DI16 I/O Pins with OSC1 or SOSCI VSS —0.2VDD V

DI18 I/O Pins with I2CVSS — 0.3 VDD V SMbus disabled

DI19 I/O Pins with I2C VSS — 0.8 V V SMbus enabled

VIH Input High Voltage

DI20 I/O Pins Not 5V Tolerant(4)

I/O Pins 5V Tolerant(4)

0.7 VDD

—

VDD

5.5

DI28 SDAx, SCLx 0.7 VDD — 5.5 V SMbus disabled

DI29 SDAx, SCLx 2.1 — 5.5 V SMbus enabled

ICNPU CNx Pull-up Current

DI30 50 250 400 μAVDD = 3.3V, VPIN = VSS

IIL Input Leakage Current(2,3)

DI50 I/O Pins 5V Tolerant(4) ——±2μAVSS ≤ VPIN ≤ VDD,

Pin at high-impedance

DI51 I/O Pins Not 5V Tolerant(4) ——±1μAVSS ≤ VPIN ≤ VDD,

Pin at high-impedance,

-40°C ≤TA ≤+85°C

DI51a I/O Pins Not 5V Tolerant(4) ——±2μA Shared with external reference

pins, -40°C ≤TA ≤+85°C

DI51b I/O Pins Not 5V Tolerant(4) ——±3.5μAVSS ≤ VPIN ≤ VDD, Pin at

high-impedance,

-40°C ≤TA ≤+125°C

DI51c I/O Pins Not 5V Tolerant(4) ——±8μA Analog pins shared with

external reference pins,

-40°C ≤TA ≤+125°C

DI55 MCLR ——±2μAVSS ≤ VPIN ≤ VDD

DI56 OSC1 — — ±2 μAVSS ≤ VPIN ≤ VDD,

XT and HS modes

Note 1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.

2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified

levels represent normal operating conditions. Higher leakage current may be measured at different input

voltages.

3: Negative current is defined as current sourced by the pin.

4: See “Pin Diagrams” for a list of 5V tolerant pins.

5: VIL source < (VSS – 0.3). Characterized but not tested.

6: Non-5V tolerant pins VIH source > (VDD + 0.3), 5V tolerant pins VIH source > 5.5V. Characterized but not

tested.

7: Digital 5V tolerant pins cannot tolerate any “positive” input injection current from input sources > 5.5V.

8: Injection currents > | 0 | can affect the ADC results by approximately 4-6 counts.

9: Any number and/or combination of I/O pins not excluded under IICL or IICH conditions are permitted pro-

vided the mathematical “absolute instantaneous” sum of the input injection currents from all pins do not

exceed the specified limit. Characterized but not tested.

dsPIC33FJXXXGPX06A/X08A/X10A

IICL Input Low Injection Current

DI60a

0—-5

(5,8) mA

All pins except VDD, VSS, AVDD,

AVSS, MCLR, VCAP, SOSCI,

SOSCO, and RB11

IICH Input High Injection Current

DI60b

0—+5

(6,7,8) mA

All pins except VDD, VSS, AVDD,

AVSS, MCLR, VCAP, SOSCI,

SOSCO, RB11, and all 5V

tolerant pins(7)

∑ IICT Total Input Injection Current

DI60c (sum of all I/O and control

pins)

-20(9) —+20

(9) mA Absolute instantaneous sum of

all ± input injection currents

from all I/O pins

(| I

ICL + | IICH |) ≤ ∑ IICT

TABLE 25-9: DC CHARACTERISTICS: I/O PIN INPUT SPECIFICATIONS (CONTINUED)

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA≤ +85°C for Industrial

-40°C ≤ TA≤+125°C for Extended

Param

No. Symbol Characteristic Min Typ(1) Max Units Conditions

Note 1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.

2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified

levels represent normal operating conditions. Higher leakage current may be measured at different input

voltages.

3: Negative current is defined as current sourced by the pin.

4: See “Pin Diagrams” for a list of 5V tolerant pins.

5: VIL source < (VSS – 0.3). Characterized but not tested.

6: Non-5V tolerant pins VIH source > (VDD + 0.3), 5V tolerant pins VIH source > 5.5V. Characterized but not

tested.

7: Digital 5V tolerant pins cannot tolerate any “positive” input injection current from input sources > 5.5V.

8: Injection currents > | 0 | can affect the ADC results by approximately 4-6 counts.

9: Any number and/or combination of I/O pins not excluded under IICL or IICH conditions are permitted pro-

vided the mathematical “absolute instantaneous” sum of the input injection currents from all pins do not

exceed the specified limit. Characterized but not tested.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-10: DC CHARACTERISTICS: I/O PIN OUTPUT SPECIFICATIONS

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic Min Typ Max Units Conditions

VOL Output Low Voltage

DO10 I/O ports — — 0.4 V IOL = 2 mA, VDD = 3.3V

DO16 OSC2/CLKO — — 0.4 V IOL = 2 mA, VDD = 3.3V

VOH Output High Voltage

DO20 I/O ports 2.40 — — V IOH = -2.3 mA, VDD = 3.3V

DO26 OSC2/CLKO 2.41 — — V IOH = -1.3 mA, VDD = 3.3V

TABLE 25-11: ELECTRICAL CHARACTERISTICS: BOR

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic Min(1) Typ Max(1) Units Conditions

BO10 VBOR BOR Event on VDD transition

high-to-low

BOR event is tied to VDD core voltage

decrease

2.40 — 2.55 V —

Note 1: Parameters are for design guidance only and are not tested in manufacturing.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-13: INTERNAL VOLTAGE REGULATOR SPECIFICATIONS

TABLE 25-12: DC CHARACTERISTICS: PROGRAM MEMORY

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic Min Typ(1) Max Units Conditions

Program Flash Memory

D130 EPCell Endurance 10,000 — — E/W

D131 VPR VDD for Read VMIN —3.6VVMIN = Minimum operating

voltage

D132b VPEW VDD for Self-Timed Write VMIN —3.6VVMIN = Minimum operating

voltage

D134 TRETD Characteristic Retention 20 — — Year Provided no other specifications

are violated

D135 IDDP Supply Current during

Programming

—10 —mA

D136a TRW Row Write Time 1.32 — 1.74 ms TRW = 11064 FRC cycles,

TA = +85°C, See Note 2

D136b TRW Row Write Time 1.28 — 1.79 ms TRW = 11064 FRC cycles,

TA = +125°C, See Note 2

D137a TPE Page Erase Time 20.1 — 26.5 ms TPE = 168517 FRC cycles,

TA = +85°C, See Note 2

D137b TPE Page Erase Time 19.5 — 27.3 ms TPE = 168517 FRC cycles,

TA = +125°C, See Note 2

D138a TWW Word Write Cycle Time 42.3 — 55.9 µs TWW = 355 FRC cycles,

TA = +85°C, See Note 2

D138b TWW Word Write Cycle Time 41.1 — 57.6 µs TWW = 355 FRC cycles,

TA = +125°C, See Note 2

Note 1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.

2: Other conditions: FRC = 7.37 MHz, TUN<5:0> = b'011111 (for Min), TUN<5:0> = b'100000 (for Max).

This parameter depends on the FRC accuracy (see Table 25-19) and the value of the FRC Oscillator

Tuning register (see Register 9-4). For complete details on calculating the Minimum and Maximum time

see Section 5.3 “Programming Operations”.

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristics Min Typ Max Units Comments

CEFC External Filter Capacitor

Value

4.7 10 — μF Capacitor must be low

series resistance

(< 5 ohms)

dsPIC33FJXXXGPX06A/X08A/X10A

25.2 AC Characteristics and Timing

Parameters

The information contained in this section defines

dsPIC33FJXXXGPX06A/X08A/X10A AC characteris-

tics and timing parameters.

TABLE 25-14: TEMPERATURE AND VOLTAGE SPECIFICATIONS – AC

FIGURE 25-1: LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS

TABLE 25-15: CAPACITIVE LOADING REQUIREMENTS ON OUTPUT PINS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤T

A ≤+125°C for Extended

Operating voltage VDD range as described in Table 25-1.

Param

No. Symbol Characteristic Min Typ Max Units Conditions

DO50 COSC2 OSC2/SOSC2 pin — — 15 pF In XT and HS modes when

external clock is used to drive

OSC1

DO56 CIO All I/O pins and OSC2 — — 50 pF EC mode

DO58 CBSCLx, SDAx — — 400 pF In I2C™ mode

VDD/2

VSS

RL=464Ω

CL= 50 pF for all pins except OSC2

15 pF for OSC2 output

Load Condition 1 - for all pins except OSC2 Load Condition 2 - for OSC2

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 25-2: EXTERNAL CLOCK TIMING

TABLE 25-16: EXTERNAL CLOCK TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic Min Typ(1) Max Units Conditions

OS10 FIN External CLKI Frequency

(External clocks allowed only

in EC and ECPLL modes)

DC — 40 MHz EC

Oscillator Crystal Frequency 3.5

—

MHz

kHz

SOSC

OS20 TOSC TOSC = 1/FOSC 12.5 — DC ns —

OS25 TCY Instruction Cycle Time(2) 25 — DC ns —

OS30 TosL,

TosH

External Clock in (OSC1)

High or Low Time

0.375 x TOSC — 0.625 x TOSC ns EC

OS31 TosR,

TosF

External Clock in (OSC1)

Rise or Fall Time

——20nsEC

OS40 TckR CLKO Rise Time(3) —5.2 — ns—

OS41 TckF CLKO Fall Time(3) —5.2 — ns—

OS42 GMExternal Oscillator

Transconductance(4)

14 16 18 mA/V VDD = 3.3V

TA = +25ºC

Note 1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.

2: Instruction cycle period (TCY) equals two times the input oscillator time-base period. All specified values

are based on characterization data for that particular oscillator type under standard operating conditions

with the device executing code. Exceeding these specified limits may result in an unstable oscillator

operation and/or higher than expected current consumption. All devices are tested to operate at “min.”

values with an external clock applied to the OSC1/CLKI pin. When an external clock input is used, the

“max.” cycle time limit is “DC” (no clock) for all devices.

3: Measurements are taken in EC mode. The CLKO signal is measured on the OSC2 pin.

4: Data for this parameter is Preliminary. This parameter is characterized, but not tested in manufacturing.

Q1 Q2 Q3 Q4

OSC1

CLKO

Q1 Q2 Q3 Q4

OS20

OS25

OS30 OS30

OS40

OS41

OS31 OS31

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-17: PLL CLOCK TIMING SPECIFICATIONS (VDD = 3.0V TO 3.6V)

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic Min Typ(1) Max Units Conditions

OS50 FPLLI PLL Voltage Controlled

Oscillator (VCO) Input

Frequency Range(2)

0.8 — 8.0 MHz ECPLL, HSPLL, XTPLL

modes

OS51 FSYS On-Chip VCO System

Frequency

100 — 200 MHz —

OS52 TLOCK PLL Start-up Time (Lock Time) 0.9 1.5 3.1 ms —

OS53 DCLK CLKO Stability (Jitter) -3.0 0.5 3.0 % Measured over 100 ms

period

Note 1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.

2: These parameters are characterized by similarity but are not tested in manufacturing. This specification is

based on clock cycle by clock cycle measurements. To calculate the effective jitter for individual time base

or communication clocks used by peripherals use the formula:

Peripheral Clock Jitter = DCLK / √(FOSC/Peripheral bit rate clock)

Example Only: Fosc = 80 MHz, DCLK = 3%, SPI bit rate clock, (i.e. SCK), is 5 MHz

SPI SCK Jitter = [ DCLK / √(80 MHz/5 MHz)] = [3%/ √16] = [3% / 4] = 0.75%

TABLE 25-18: AC CHARACTERISTICS: INTERNAL FRC ACCURACY

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Characteristic Min Typ Max Units Conditions

Internal FRC Accuracy @ FRC Frequency = 7.37 MHz(1)

F20a FRC -2 — +2 % -40°C ≤ TA ≤ +85°C VDD = 3.0-3.6V

F20b FRC -5 — +5 % -40°C ≤ TA ≤ +125°C VDD = 3.0-3.6V

Note 1: Frequency calibrated at 25°C and 3.3V. TUN bits can be used to compensate for temperature drift.

TABLE 25-19: INTERNAL LPRC ACCURACY

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Characteristic Min Typ Max Units Conditions

LPRC @ 32.768 kHz(1)

F21a LPRC -30 — +30 % -40°C ≤ TA ≤ +85°C

F21b LPRC -35 — +35 % -40°C ≤ TA ≤ +125°C

Note 1: Change of LPRC frequency as VDD changes.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 25-3: CLKO AND I/O TIMING CHARACTERISTICS

TABLE 25-20: I/O TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic Min Typ(1) Max Units Conditions

DO31 TIOR Port Output Rise Time — 10 25 ns —

DO32 TIOF Port Output Fall Time — 10 25 ns —

DI35 TINP INTx Pin High or Low Time (input) 20 — — ns —

DI40 TRBP CNx High or Low Time (input) 2 — — TCY —

Note 1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.

Note: Refer to Figure 25-1 for load conditions.

I/O Pin

(Input)

I/O Pin

(Output)

DI35

Old Value New Value

DI40

DO31

DO32

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 25-4: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP

TIMER TIMING CHARACTERISTICS

VDD

MCLR

Internal

POR

PWRT

Time-out

OSC

Time-out

Internal

Reset

Watchdog

Timer

Reset

SY11

SY10

SY20

SY13

I/O Pins

SY13

Note: Refer to Figure 25-1 for load conditions.

FSCM

Delay

SY35

SY30

SY12

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-21: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER

TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic(1) Min Typ(2) Max Units Conditions

SY10 TMCLMCLR Pulse-Width (low) 2 — — μs -40°C to +85°C

SY11 TPWRT Power-up Timer Period —

—

128

—

ms -40°C to +85°C

User programmable

SY12 TPOR Power-on Reset Delay 3 10 30 μs -40°C to +85°C

SY13 TIOZ I/O High-Impedance from

MCLR Low or Watchdog

Timer Reset

0.68 0.72 1.2 μs—

SY20 TWDT1 Watchdog Timer

Time-out Period

— — — — See Section 22.4 “Watchdog

Timer (WDT)” and LPRC

specification F21 (Table 25-19)

SY30 TOST Oscillator Start-up Timer

Period

— 1024 TOSC ——TOSC = OSC1 period

SY35 TFSCM Fail-Safe Clock Monitor

Delay

— 500 900 μs -40°C to +85°C

Note 1: These parameters are characterized but not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 25-5: TIMER1, 2, 3, 4, 5, 6, 7, 8 AND 9 EXTERNAL CLOCK TIMING CHARACTERISTICS

Note: Refer to Figure 25-1 for load conditions.

Tx11

Tx15

Tx10

Tx20

TMRx

OS60

TxCK

TABLE 25-22: TIMER1 EXTERNAL CLOCK TIMING REQUIREMENTS(1)

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤T

A ≤+125°C for Extended

Param

No. Symbol Characteristic Min Typ Max Units Conditions

TA10 TTXH TxCK High Time Synchronous,

no prescaler

TCY + 20 — — ns Must also meet

parameter TA15

Synchronous,

with prescaler

(TCY + 20)/N — — ns

Asynchronous 20 — — ns

TA11 TTXL TxCK Low Time Synchronous,

no prescaler

(TCY + 20)/N — — ns Must also meet

parameter TA15

Synchronous,

with prescaler

20 — — ns N = prescale

value

(1,8,64,256)

Asynchronous 20 — — ns

TA15 TTXP TxCK Input

Period

Synchronous,

no prescaler

2TCY + 40 — — ns —

Synchronous,

with prescaler

Greater of

40 ns or

(2TCY + 40)/N

———N = prescale

value

(1, 8, 64, 256)

Asynchronous 40 — — ns —

OS60 Ft1 SOSC1/T1CK Oscillator Input

frequency Range (oscillator

enabled by setting TCS bit

(T1CON<1>))

DC — 50 kHz —

TA20 TCKEXTMRL Delay from External TxCK

Clock Edge to Timer Increment

0.75TCY+40 — 1.75TCY+40 ns —

Note 1: Timer1 is a Type A.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-23: TIMER2, TIMER4, TIMER6 AND TIMER8 EXTERNAL CLOCK TIMING

REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic(1) Min Typ Max Units Conditions

TB10 TtxH TxCK High

Time

Synchronous

mode

Greater of

20 or

CY + 20)/N

— — ns Must also meet

parameter TB15

N = prescale

value

(1, 8, 64, 256)

TB11 TtxL TxCK Low

Time

Synchronous

mode

Greater of:

20 or

CY + 20)/N

——ns

Must also meet

parameter TB15

N = prescale

value

(1, 8, 64, 256)

TB15 TtxP TxCK Input

Period

Synchronous

mode

Greater of:

40 or

(2 TCY + 40)/N

— — ns N = prescale

value

(1, 8, 64, 256)

TB20 TCKEXTMRL Delay from External TxCK

Clock Edge to Timer Incre-

ment

0.75 TCY + 40 — 1.75 TCY + 40 ns

Note 1: These parameters are characterized, but are not tested in manufacturing.

TABLE 25-24: TIMER3, TIMER5, TIMER7 AND TIMER9 EXTERNAL CLOCK TIMING

REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic(1) Min Typ Max Units Conditions

TC10 TtxH TxCK High

Time

Synchronous TCY + 20 — — ns Must also meet

parameter TC15

TC11 TtxL TxCK Low

Time

Synchronous TCY + 20 — — ns Must also meet

parameter TC15

TC15 TtxP TxCK Input

Period

Synchronous,

with prescaler

2TCY + 40 — — ns N = prescale

value

(1, 8, 64, 256)

TC20 TCKEXTMRL Delay from External TxCK

Clock Edge to Timer Incre-

ment

0.75 TCY + 40 — 1.75 TCY + 40 ns

Note 1: These parameters are characterized, but are not tested in manufacturing.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 25-6: INPUT CAPTURE (CAPx) TIMING CHARACTERISTICS

FIGURE 25-7: OUTPUT COMPARE MODULE (OCx) TIMING CHARACTERISTICS

TABLE 25-25: INPUT CAPTURE TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic(1) Min Max Units Conditions

IC10 TccL ICx Input Low Time No Prescaler 0.5 TCY + 20 — ns —

With Prescaler 10 — ns

IC11 TccH ICx Input High Time No Prescaler 0.5 TCY + 20 — ns —

With Prescaler 10 — ns

IC15 TccP ICx Input Period (TCY + 40)/N — ns N = prescale

value (1, 4, 16)

Note 1: These parameters are characterized but not tested in manufacturing.

TABLE 25-26: OUTPUT COMPARE MODULE TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic(1) Min Typ Max Units Conditions

OC10 TccF OCx Output Fall Time — — — ns See parameter D032

OC11 TccR OCx Output Rise Time — — — ns See parameter D031

Note 1: These parameters are characterized but not tested in manufacturing.

ICx

IC10 IC11

IC15

Note: Refer to Figure 25-1 for load conditions.

OCx

OC11 OC10

(Output Compare

Note: Refer to Figure 25-1 for load conditions.

or PWM Mode)

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 25-8: OC/PWM MODULE TIMING CHARACTERISTICS

TABLE 25-27: SIMPLE OC/PWM MODE TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic(1) Min Typ Max Units Conditions

OC15 TFD Fault Input to PWM I/O

Change

——TCY+20 ns —

OC20 TFLT Fault Input Pulse-Width TCY+20 — — ns —

Note 1: These parameters are characterized but not tested in manufacturing.

OCFA/OCFB

OCx

OC20

OC15

Active Tri-state

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-28: SPIx MAXIMUM DATA/CLOCK RATE SUMMARY

FIGURE 25-9: SPIx MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY CKE = 0) TIMING

CHARACTERISTICS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Maximum

Data Rate

Master

Transmit Only

(Half-Duplex)

Master

Transmit/Receive

(Full-Duplex)

Slave

Transmit/Receive

(Full-Duplex)

CKE CKP SMP

15 Mhz Table 25-29 ——0,10,10,1

10 Mhz — Table 25-30 —10,11

10 Mhz — Table 25-31 —00,11

15 Mhz — — Table 25-32 100

11 Mhz — — Table 25-33 110

15 Mhz — — Table 25-34 010

11 Mhz — — Table 25-35 000

SCKx

(CKP = 0)

SCKx

(CKP = 1)

SDOx

SP10

SP21

SP20

SP35

SP20

SP21

MSb LSb

Bit 14 - - - - - -1

SP30, SP31

Note: Refer to Figure 25-1 for load conditions.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 25-10: SPIx MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY CKE = 1) TIMING

CHARACTERISTICS

TABLE 25-29: SPIx MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY) TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic(1) Min Typ(2) Max Units Conditions

SP10 TscP Maximum SCK Frequency — — 15 MHz See Note 3

SP20 TscF SCKx Output Fall Time — — — ns See parameter DO32

and Note 4

SP21 TscR SCKx Output Rise Time — — — ns See parameter DO31

and Note 4

SP30 TdoF SDOx Data Output Fall Time — — — ns See parameter DO32

and Note 4

SP31 TdoR SDOx Data Output Rise Time — — — ns See parameter DO31

and Note 4

SP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

—620ns —

SP36 TdiV2scH,

TdiV2scL

SDOx Data Output Setup to

First SCKx Edge

30 — — ns —

Note 1: These parameters are characterized, but are not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.

3: The minimum clock period for SCKx is 66.7 ns. Therefore, the clock generated in Master mode must not

violate this specification.

4: Assumes 50 pF load on all SPIx pins.

SCKx

(CKP = 0)

SCKx

(CKP = 1)

SDOx

SP10

SP21

SP20

SP35

SP20

SP21

MSb LSb

Bit 14 - - - - - -1

SP30, SP31

Note: Refer to Figure 25-1 for load conditions.

SP36

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 25-11: SPIx MASTER MODE (FULL-DUPLEX, CKE = 1, CKP = X, SMP = 1) TIMING

CHARACTERISTICS

TABLE 25-30: SPIx MASTER MODE (FULL-DUPLEX, CKE = 1, CKP = x, SMP = 1) TIMING

REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic(1) Min Typ(2) Max Units Conditions

SP10 TscP Maximum SCK Frequency — — 10 MHz See Note 3

SP20 TscF SCKx Output Fall Time — — — ns See parameter DO32

and Note 4

SP21 TscR SCKx Output Rise Time — — — ns See parameter DO31

and Note 4

SP30 TdoF SDOx Data Output Fall Time — — — ns See parameter DO32

and Note 4

SP31 TdoR SDOx Data Output Rise Time — — — ns See parameter DO31

and Note 4

SP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

— 6 20 ns —

SP36 TdoV2sc,

TdoV2scL

SDOx Data Output Setup to

First SCKx Edge

30 — — ns —

SP40 TdiV2scH,

TdiV2scL

Setup Time of SDIx Data

Input to SCKx Edge

30 — — ns —

SP41 TscH2diL,

TscL2diL

Hold Time of SDIx Data Input

to SCKx Edge

30 — — ns —

Note 1: These parameters are characterized, but are not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.

3: The minimum clock period for SCKx is 100 ns. The clock generated in Master mode must not violate this

specification.

4: Assumes 50 pF load on all SPIx pins.

SCKx

(CKP = 0)

SCKx

(CKP = 1)

SDOx

SP10

SP21

SP20

SP35

SP20

SP21

MSb LSb

Bit 14 - - - - - -1

SP30, SP31

Note: Refer to Figure 25-1 for load conditions.

SP36

SP41

MSb In LSb In

Bit 14 - - - -1

SDIx

SP40

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 25-12: SPIx MASTER MODE (FULL-DUPLEX, CKE = 0, CKP = X, SMP = 1) TIMING

CHARACTERISTICS

TABLE 25-31: SPIx MASTER MODE (FULL-DUPLEX, CKE = 0, CKP = x, SMP = 1) TIMING

REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 2.4V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic(1) Min Typ(2) Max Units Conditions

SP10 TscP Maximum SCK Frequency — — 10 MHz -40ºC to +125ºC and

see Note 3

SP20 TscF SCKx Output Fall Time — — — ns See parameter DO32

and Note 4

SP21 TscR SCKx Output Rise Time — — — ns See parameter DO31

and Note 4

SP30 TdoF SDOx Data Output Fall Time — — — ns See parameter DO32

and Note 4

SP31 TdoR SDOx Data Output Rise Time — — — ns See parameter DO31

and Note 4

SP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

— 6 20 ns —

SP36 TdoV2scH,

TdoV2scL

SDOx Data Output Setup to

First SCKx Edge

30 — — ns —

SP40 TdiV2scH,

TdiV2scL

Setup Time of SDIx Data

Input to SCKx Edge

30 — — ns —

SP41 TscH2diL,

TscL2diL

Hold Time of SDIx Data Input

to SCKx Edge

30 — — ns —

Note 1: These parameters are characterized, but are not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.

3: The minimum clock period for SCKx is 100 ns. The clock generated in Master mode must not violate this

specification.

4: Assumes 50 pF load on all SPIx pins.

SCKx

(CKP = 0)

SCKx

(CKP = 1)

SDOx

SDIx

SP10

SP40 SP41

SP21

SP20

SP35

SP20

SP21

MSb LSb

Bit 14 - - - - - -1

MSb In LSb In

Bit 14 - - - -1

SP30, SP31

Note: Refer to Figure 25-1 for load conditions.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 25-13: SPIx SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 0, SMP = 0) TIMING

CHARACTERISTICS

SSx

SCKx

(CKP = 0)

SCKx

(CKP = 1)

SDOx

SDI

SP50

SP60

SDIx

SP30,SP31

MSb Bit 14 - - - - - -1 LSb

SP51

MSb In Bit 14 - - - -1 LSb In

SP35

SP52

SP73

SP72

SP73

SP70

SP40

SP41

Note: Refer to Figure 25-1 for load conditions.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-32: SPIx SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 0, SMP = 0) TIMING

REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 2.4V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic(1) Min Typ(2) Max Units Conditions

SP70 TscP Maximum SCK Input Frequency — — 15 MHz See Note 3

SP72 TscF SCKx Input Fall Time — — — ns See parameter DO32

and Note 4

SP73 TscR SCKx Input Rise Time — — — ns See parameter DO31

and Note 4

SP30 TdoF SDOx Data Output Fall Time — — — ns See parameter DO32

and Note 4

SP31 TdoR SDOx Data Output Rise Time — — — ns See parameter DO31

and Note 4

SP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

—620ns —

SP36 TdoV2scH,

TdoV2scL

SDOx Data Output Setup to

First SCKx Edge

30 — — ns —

SP40 TdiV2scH,

TdiV2scL

Setup Time of SDIx Data Input

to SCKx Edge

30 — — ns —

SP41 TscH2diL,

TscL2diL

Hold Time of SDIx Data Input

to SCKx Edge

30 — — ns —

SP50 TssL2scH,

TssL2scL

SSx ↓ to SCKx ↑ or SCKx Input 120 — — ns —

SP51 TssH2doZ SSx ↑ to SDOx Output

High-Impedance(4)

10 — 50 ns —

SP52 TscH2ssH

TscL2ssH

SSx after SCKx Edge 1.5 TCY + 40 — — ns See Note 4

SP60 TssL2doV SDOx Data Output Valid after

SSx Edge

——50ns —

Note 1: These parameters are characterized, but are not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.

3: The minimum clock period for SCKx is 66.7 ns. Therefore, the SCK clock generated by the Master must

not violate this specificiation.

4: Assumes 50 pF load on all SPIx pins.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 25-14: SPIx SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 1, SMP = 0) TIMING

CHARACTERISTICS

SSx

SCKx

(CKP = 0)

SCKx

(CKP = 1)

SDOx

SDI

SP50

SP60

SDIx

SP30,SP31

MSb Bit 14 - - - - - -1 LSb

SP51

MSb In Bit 14 - - - -1 LSb In

SP35

SP52

SP73

SP72

SP73

SP70

SP40

SP41

Note: Refer to Figure 25-1 for load conditions.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-33: SPIx SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 1, SMP = 0) TIMING

REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 2.4V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic(1) Min Typ(2) Max Units Conditions

SP70 TscP Maximum SCK Input Frequency — — 11 MHz See Note 3

SP72 TscF SCKx Input Fall Time — — — ns See parameter DO32

and Note 4

SP73 TscR SCKx Input Rise Time — — — ns See parameter DO31

and Note 4

SP30 TdoF SDOx Data Output Fall Time — — — ns See parameter DO32

and Note 4

SP31 TdoR SDOx Data Output Rise Time — — — ns See parameter DO31

and Note 4

SP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

—620ns —

SP36 TdoV2scH,

TdoV2scL

SDOx Data Output Setup to

First SCKx Edge

30 — — ns —

SP40 TdiV2scH,

TdiV2scL

Setup Time of SDIx Data Input

to SCKx Edge

30 — — ns —

SP41 TscH2diL,

TscL2diL

Hold Time of SDIx Data Input

to SCKx Edge

30 — — ns —

SP50 TssL2scH,

TssL2scL

SSx ↓ to SCKx ↑ or SCKx Input 120 — — ns —

SP51 TssH2doZ SSx ↑ to SDOx Output

High-Impedance(4)

10 — 50 ns —

SP52 TscH2ssH

TscL2ssH

SSx after SCKx Edge 1.5 TCY + 40 — — ns See Note 4

SP60 TssL2doV SDOx Data Output Valid after

SSx Edge

——50ns —

Note 1: These parameters are characterized, but are not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.

3: The minimum clock period for SCKx is 91 ns. Therefore, the SCK clock generated by the Master must not

violate this specificiation.

4: Assumes 50 pF load on all SPIx pins.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 25-15: SPIx SLAVE MODE (FULL-DUPLEX CKE = 0, CKP = 1, SMP = 0) TIMING

CHARACTERISTICS

SSX

SCKX

(CKP = 0)

SCKX

(CKP = 1)

SDOX

SP50

SP40

SP41

SP30,SP31 SP51

SP35

MSb LSb

Bit 14 - - - - - -1

MSb In Bit 14 - - - -1 LSb In

SP52

SP73

SP72

SP73

SP70

Note: Refer to Figure 25-1 for load conditions.

SDIX

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-34: SPIx SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 1, SMP = 0) TIMING

REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 2.4V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic(1) Min Typ(2) Max Units Conditions

SP70 TscP Maximum SCK Input Frequency — — 15 MHz See Note 3

SP72 TscF SCKx Input Fall Time — — — ns See parameter DO32

and Note 4

SP73 TscR SCKx Input Rise Time — — — ns See parameter DO31

and Note 4

SP30 TdoF SDOx Data Output Fall Time — — — ns See parameter DO32

and Note 4

SP31 TdoR SDOx Data Output Rise Time — — — ns See parameter DO31

and Note 4

SP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

—620ns —

SP36 TdoV2scH,

TdoV2scL

SDOx Data Output Setup to

First SCKx Edge

30 — — ns —

SP40 TdiV2scH,

TdiV2scL

Setup Time of SDIx Data Input

to SCKx Edge

30 — — ns —

SP41 TscH2diL,

TscL2diL

Hold Time of SDIx Data Input

to SCKx Edge

30 — — ns —

SP50 TssL2scH,

TssL2scL

SSx ↓ to SCKx ↑ or SCKx Input 120 — — ns —

SP51 TssH2doZ SSx ↑ to SDOx Output

High-Impedance(4)

10 — 50 ns —

SP52 TscH2ssH

TscL2ssH

SSx after SCKx Edge 1.5 TCY + 40 — — ns See Note 4

Note 1: These parameters are characterized, but are not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.

3: The minimum clock period for SCKx is 66.7 ns. Therefore, the SCK clock generated by the Master must

not violate this specificiation.

4: Assumes 50 pF load on all SPIx pins.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 25-16: SPIx SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 0, SMP = 0) TIMING

CHARACTERISTICS

SSX

SCKX

(CKP = 0)

SCKX

(CKP = 1)

SDOX

SP50

SP40

SP41

SP30,SP31 SP51

SP35

MSb LSb

Bit 14 - - - - - -1

MSb In Bit 14 - - - -1 LSb In

SP52

SP73

SP72

SP73

SP70

Note: Refer to Figure 25-1 for load conditions.

SDIX

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-35: SPIx SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 0, SMP = 0) TIMING

REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 2.4V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic(1) Min Typ(2) Max Units Conditions

SP70 TscP Maximum SCK Input Frequency — — 11 MHz See Note 3

SP72 TscF SCKx Input Fall Time — — — ns See parameter DO32

and Note 4

SP73 TscR SCKx Input Rise Time — — — ns See parameter DO31

and Note 4

SP30 TdoF SDOx Data Output Fall Time — — — ns See parameter DO32

and Note 4

SP31 TdoR SDOx Data Output Rise Time — — — ns See parameter DO31

and Note 4

SP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

—620ns —

SP36 TdoV2scH,

TdoV2scL

SDOx Data Output Setup to

First SCKx Edge

30 — — ns —

SP40 TdiV2scH,

TdiV2scL

Setup Time of SDIx Data Input

to SCKx Edge

30 — — ns —

SP41 TscH2diL,

TscL2diL

Hold Time of SDIx Data Input

to SCKx Edge

30 — — ns —

SP50 TssL2scH,

TssL2scL

SSx ↓ to SCKx ↑ or SCKx Input 120 — — ns —

SP51 TssH2doZ SSx ↑ to SDOx Output

High-Impedance(4)

10 — 50 ns —

SP52 TscH2ssH

TscL2ssH

SSx after SCKx Edge 1.5 TCY + 40 — — ns See Note 4

Note 1: These parameters are characterized, but are not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.

3: The minimum clock period for SCKx is 91 ns. Therefore, the SCK clock generated by the Master must not

violate this specificiation.

4: Assumes 50 pF load on all SPIx pins.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 25-17: I2Cx BUS START/STOP BITS TIMING CHARACTERISTICS (MASTER MODE)

FIGURE 25-18: I2Cx BUS DATA TIMING CHARACTERISTICS (MASTER MODE)

IM31 IM34

SCLx

SDAx

Start

Condition

Stop

Condition

IM30 IM33

Note: Refer to Figure 25-1 for load conditions.

IM11 IM10 IM33

IM11

IM10

IM20

IM26 IM25

IM40 IM40 IM45

IM21

SCLx

SDAx

Out

Note: Refer to Figure 25-1 for load conditions.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-36: I2Cx BUS DATA TIMING REQUIREMENTS (MASTER MODE)

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic Min(1) Max Units Conditions

IM10 TLO:SCL Clock Low Time 100 kHz mode TCY/2 (BRG + 1) — μs—

400 kHz mode TCY/2 (BRG + 1) — μs—

1 MHz mode(2) TCY/2 (BRG + 1) — μs—

IM11 THI:SCL Clock High Time 100 kHz mode TCY/2 (BRG + 1) — μs—

400 kHz mode TCY/2 (BRG + 1) — μs—

1 MHz mode(2) TCY/2 (BRG + 1) — μs—

IM20 TF:SCL SDAx and SCLx

Fall Time

100 kHz mode — 300 ns CB is specified to be

from 10 to 400 pF

400 kHz mode 20 + 0.1 CB300 ns

1 MHz mode(2) — 100 ns

IM21 TR:SCL SDAx and SCLx

Rise Time

100 kHz mode — 1000 ns CB is specified to be

from 10 to 400 pF

400 kHz mode 20 + 0.1 CB300 ns

1 MHz mode(2) — 300 ns

IM25 TSU:DAT Data Input

Setup Time

100 kHz mode 250 — ns —

400 kHz mode 100 — ns

1 MHz mode(2) 40 — ns

IM26 THD:DAT Data Input

Hold Time

100 kHz mode 0 — μs—

400 kHz mode 0 0.9 μs

1 MHz mode(2) 0.2 — μs

IM30 TSU:STA Start Condition

Setup Time

100 kHz mode TCY/2 (BRG + 1) — μs Only relevant for

Repeated Start

condition

400 kHz mode TCY/2 (BRG + 1) — μs

1 MHz mode(2) TCY/2 (BRG + 1) — μs

IM31 THD:STA Start Condition

Hold Time

100 kHz mode TCY/2 (BRG + 1) — μs After this period the

first clock pulse is

generated

400 kHz mode TCY/2 (BRG + 1) — μs

1 MHz mode(2) TCY/2 (BRG + 1) — μs

IM33 TSU:STO Stop Condition

Setup Time

100 kHz mode TCY/2 (BRG + 1) — μs—

400 kHz mode TCY/2 (BRG + 1) — μs

1 MHz mode(2) TCY/2 (BRG + 1) — μs

IM34 THD:STO Stop Condition 100 kHz mode TCY/2 (BRG + 1) — ns —

Hold Time 400 kHz mode TCY/2 (BRG + 1) — ns

1 MHz mode(2) TCY/2 (BRG + 1) — ns

IM40 TAA:SCL Output Valid

From Clock

100 kHz mode — 3500 ns —

400 kHz mode — 1000 ns —

1 MHz mode(2) — 400 ns —

IM45 TBF:SDA Bus Free Time 100 kHz mode 4.7 — μs Time the bus must be

free before a new

transmission can start

400 kHz mode 1.3 — μs

1 MHz mode(2) 0.5 — μs

IM50 CBBus Capacitive Loading — 400 pF —

IM51 TPGD Pulse Gobbler Delay 65 390 ns See Note 3

Note 1: BRG is the value of the I2C Baud Rate Generator. Refer to Section 19. “Inter-Integrated Circuit™

(I2C™)” (DS70195) in the “dsPIC33F/PIC24H Family Reference Manual”.

2: Maximum pin capacitance = 10 pF for all I2Cx pins (for 1 MHz mode only).

3: Typical value for this parameter is 130 ns.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 25-19: I2Cx BUS START/STOP BITS TIMING CHARACTERISTICS (SLAVE MODE)

FIGURE 25-20: I2Cx BUS DATA TIMING CHARACTERISTICS (SLAVE MODE)

IS31 IS34

SCLx

SDAx

Start

Condition

Stop

Condition

IS30 IS33

IS30 IS31 IS33

IS11

IS10

IS20

IS26 IS25

IS40 IS40 IS45

IS21

SCLx

SDAx

Out

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-37: I2Cx BUS DATA TIMING REQUIREMENTS (SLAVE MODE)

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic Min Max Units Conditions

IS10 TLO:SCL Clock Low Time 100 kHz mode 4.7 — μs Device must operate at a

minimum of 1.5 MHz

400 kHz mode 1.3 — μs Device must operate at a

minimum of 10 MHz

1 MHz mode(1) 0.5 — μs—

IS11 THI:SCL Clock High Time 100 kHz mode 4.0 — μs Device must operate at a

minimum of 1.5 MHz

400 kHz mode 0.6 — μs Device must operate at a

minimum of 10 MHz

1 MHz mode(1) 0.5 — μs—

IS20 TF:SCL SDAx and SCLx

Fall Time

100 kHz mode — 300 ns CB is specified to be from

10 to 400 pF

400 kHz mode 20 + 0.1 CB300 ns

1 MHz mode(1) —100ns

IS21 TR:SCL SDAx and SCLx

Rise Time

100 kHz mode — 1000 ns CB is specified to be from

10 to 400 pF

400 kHz mode 20 + 0.1 CB300 ns

1 MHz mode(1) —300ns

IS25 TSU:DAT Data Input

Setup Time

100 kHz mode 250 — ns —

400 kHz mode 100 — ns

1 MHz mode(1) 100 — ns

IS26 THD:DAT Data Input

Hold Time

100 kHz mode 0 — μs—

400 kHz mode 0 0.9 μs

1 MHz mode(1) 00.3μs

IS30 TSU:STA Start Condition

Setup Time

100 kHz mode 4.7 — μs Only relevant for Repeated

Start condition

400 kHz mode 0.6 — μs

1 MHz mode(1) 0.25 — μs

IS31 THD:STA Start Condition

Hold Time

100 kHz mode 4.0 — μs After this period, the first

clock pulse is generated

400 kHz mode 0.6 — μs

1 MHz mode(1) 0.25 — μs

IS33 TSU:STO Stop Condition

Setup Time

100 kHz mode 4.7 — μs—

400 kHz mode 0.6 — μs

1 MHz mode(1) 0.6 — μs

IS34 THD:STO Stop Condition

Hold Time

100 kHz mode 4000 — ns —

400 kHz mode 600 — ns

1 MHz mode(1) 250 ns

IS40 TAA:SCL Output Valid

From Clock

100 kHz mode 0 3500 ns —

400 kHz mode 0 1000 ns

1 MHz mode(1) 0350ns

IS45 TBF:SDA Bus Free Time 100 kHz mode 4.7 — μs Time the bus must be free

before a new transmission

can start

400 kHz mode 1.3 — μs

1 MHz mode(1) 0.5 — μs

IS50 CBBus Capacitive Loading — 400 pF —

Note 1: Maximum pin capacitance = 10 pF for all I2Cx pins (for 1 MHz mode only).

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 25-21: DCI MODULE (MULTI-CHANNEL, I2S MODES) TIMING CHARACTERISTICS

COFS

CSCK

(SCKE =

)

CSCK

(SCKE =

)

CSDO

CSDI

CS11 CS10

CS40 CS41

CS21

CS20

CS35

CS21

MSb LSb

MSb In LSb In

CS31

High-Z High-Z

CS30

CS51 CS50

CS55

Note: Refer to Figure 25-1 for load conditions.

CS20

CS56

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-38: DCI MODULE (MULTI-CHANNEL, I2S MODES) TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic(1) Min Typ(2) Max Units Conditions

CS10 TCSCKL CSCK Input Low Time

(CSCK pin is an input)

TCY/2 + 20 — — ns —

CSCK Output Low Time(3)

(CSCK pin is an output)

30 — — ns —

CS11 TCSCKH CSCK Input High Time

(CSCK pin is an input)

TCY/2 + 20 — — ns —

CSCK Output High Time(3)

(CSCK pin is an output)

30 — — ns —

CS20 TCSCKF CSCK Output Fall Time(4)

(CSCK pin is an output)

—1025ns —

CS21 TCSCKR CSCK Output Rise Time(4)

(CSCK pin is an output)

—1025ns —

CS30 TCSDOF CSDO Data Output Fall Time(4) —1025ns —

CS31 TCSDOR CSDO Data Output Rise Time(4) —1025ns —

CS35 TDV Clock Edge to CSDO Data Valid — — 10 ns —

CS36 TDIV Clock Edge to CSDO Tri-Stated 10 — 20 ns —

CS40 TCSDI Setup Time of CSDI Data Input

CSCK Edge (CSCK pin is input

or output)

20 — — ns —

CS41 THCSDI Hold Time of CSDI Data Input to

CSCK Edge (CSCK pin is input

or output)

20 — — ns —

CS50 TCOFSF COFS Fall Time

(COFS pin is output)

—1025nsNote 1

CS51 TCOFSR COFS Rise Time

(COFS pin is output)

—1025nsNote 1

CS55 TSCOFS Setup Time of COFS Data Input

to CSCK Edge (COFS pin is

input)

20 — — ns —

CS56 THCOFS Hold Time of COFS Data Input to

CSCK Edge (COFS pin is input)

20 — — ns —

Note 1: These parameters are characterized but not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only

and are not tested.

3: The minimum clock period for CSCK is 100 ns. Therefore, the clock generated in Master mode must not

violate this specification.

4: Assumes 50 pF load on all DCI pins.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 25-22: DCI MODULE (AC-LINK MODE) TIMING CHARACTERISTICS

TABLE 25-39: DCI MODULE (AC-LINK MODE) TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic(1,2) Min Typ(3) Max Units Conditions

CS60 TBCLKL BIT_CLK Low Time 36 40.7 45 ns —

CS61 TBCLKH BIT_CLK High Time 36 40.7 45 ns —

CS62 TBCLK BIT_CLK Period — 81.4 — ns Bit clock is input

CS65 TSACL Input Setup Time to

Falling Edge of BIT_CLK

——10ns —

CS66 THACL Input Hold Time from

Falling Edge of BIT_CLK

——10ns —

CS70 TSYNCLO SYNC Data Output Low Time — 19.5 — μsNote 1

CS71 TSYNCHI SYNC Data Output High Time — 1.3 — μsNote 1

CS72 TSYNC SYNC Data Output Period — 20.8 — μsNote 1

CS75 TRACL Rise Time, SYNC, SDATA_OUT — 10 25 ns CLOAD = 50 pF, VDD = 5V

CS76 TFACL Fall Time, SYNC, SDATA_OUT — 10 25 ns CLOAD = 50 pF, VDD = 5V

CS77 TRACL Rise Time, SYNC, SDATA_OUT — — 30 ns CLOAD = 50 pF, VDD = 3V

CS78 TFACL Fall Time, SYNC, SDATA_OUT — — 30 ns CLOAD = 50 pF, VDD = 3V

CS80 TOVDACL Output Valid Delay from Rising

Edge of BIT_CLK

——15ns —

Note 1: These parameters are characterized but not tested in manufacturing.

2: These values assume BIT_CLK frequency is 12.288 MHz.

3: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only

and are not tested.

SYNC

BIT_CLK

SDOx

SDIx

CS61 CS60

CS65 CS66

CS80

CS21

MSb In

CS75

LSb

CS76

(COFS)

(CSCK)

LSb

MSb

CS72

CS71 CS70

CS76 CS75

(CSDO)

(CSDI)

CS62 CS20

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 25-23: CAN MODULE I/O TIMING CHARACTERISTICS

CiTx Pin

(output)

CA10 CA11

Old Value New Value

CA20

CiRx Pin

(input)

TABLE 25-40: ECAN™ MODULE I/O TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C

-40°C ≤TA ≤+125°C for Extended

Param

No. Symbol Characteristic(1) Min Typ Max Units Conditions

CA10 TioF Port Output Fall Time — — — ns See parameter D032

CA11 TioR Port Output Rise Time — — — ns See parameter D031

CA20 Tcwf Pulse Width to Trigger

CAN Wake-up Filter

120 — — ns —

Note 1: These parameters are characterized but not tested in manufacturing.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-41: ADC MODULE SPECIFICATIONS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤ TA ≤ +125°C for Extended

Param

No. Symbol Characteristic Min. Typ Max. Units Conditions

Device Supply

AD01 AVDD Module VDD Supply Greater of

VDD - 0.3

or 3.0

— Lesser of

VDD + 0.3

or 3.6

V—

AD02 AVSS Module VSS Supply VSS - 0.3 — VSS + 0.3 V —

Reference Inputs

AD05 VREFH Reference Voltage High AVSS + 2.5 — AVDD V

AD05a 3.0 — 3.6 V VREFH = AVDD

VREFL = AVSS = 0

AD06 VREFL Reference Voltage Low AVSS —AVDD - 2.5 V

AD06a 0 — 0 V VREFH = AVDD

VREFL = AVSS = 0

AD07 VREF Absolute Reference

Voltage

2.5 — 3.6 V VREF = VREFH - VREFL

AD08 IREF Current Drain — — 1 μA ADC off

AD08a IAD Operating Current —

—

7.0

2.7

9.0

3.2

10-bit ADC mode, See Note 1

12-bit ADC mode, See Note 1

Analog Input

AD12 VINH Input Voltage Range

VINH

VINL —VREFH V This voltage reflects Sample

and Hold Channels 0, 1, 2,

and 3 (CH0-CH3), positive

input.

AD13 VINL Input Voltage Range

VINL

VREFL —AVSS + 1V V This voltage reflects Sample

and Hold Channels 0, 1, 2,

and 3 (CH0-CH3), negative

input.

AD17 RIN Recommended Imped-

ance of Analog Voltage

Source

— — 200

200

10-bit

12-bit

Note 1: These parameters are not characterized or tested in manufacturing.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-42: ADC MODULE SPECIFICATIONS (12-BIT MODE)(2)

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤ TA ≤ +125°C for Extended

Param

No. Symbol Characteristic Min. Typ Max. Units Conditions

ADC Accuracy (12-bit Mode) - Measurements with external VREF+/VREF-

AD20a Nr Resolution 12 data bits bits

AD21a INL Integral Nonlinearity -2 — +2 LSb VINL = AVSS = VREFL =

0V, AVDD = VREFH = 3.6V

AD22a DNL Differential Nonlinearity >-1 — <1 LSb VINL = AVSS = VREFL =

0V, AVDD = VREFH = 3.6V

AD23a GERR Gain Error — 3.4 10 LSb VINL = AVSS = VREFL =

0V, AVDD = VREFH = 3.6V

AD24a EOFF Offset Error — 0.9 5 LSb VINL = AVSS = VREFL =

0V, AVDD = VREFH = 3.6V

AD25a — Monotonicity(1) — — — — Guaranteed

ADC Accuracy (12-bit Mode) - Measurements with internal VREF+/VREF-

AD20a Nr Resolution 12 data bits bits

AD21a INL Integral Nonlinearity -2 — +2 LSb VINL = AVSS = VREFL =

0V, AVDD = VREFH = 3.6V

AD22a DNL Differential Nonlinearity >-1 — <1 LSb VINL = AVSS = VREFL =

0V, AVDD = VREFH = 3.6V

AD23a GERR Gain Error — 10.5 20 LSb VINL = AVSS = VREFL =

0V, AVDD = VREFH = 3.6V

AD24a EOFF Offset Error — 3.8 10 LSb VINL = AVSS = VREFL =

0V, AVDD = VREFH = 3.6V

AD25a — Monotonicity(1) — — — — Guaranteed

Dynamic Performance (12-bit Mode)

AD30a THD Total Harmonic Distortion — — -75 dB —

AD31a SINAD Signal to Noise and

Distortion

68.5 69.5 — dB —

AD32a SFDR Spurious Free Dynamic

Range

80 — — dB —

AD33a FNYQ Input Signal Band-Width — — 250 kHz —

AD34a ENOB Effective Number of Bits 11.09 11.3 — bits —

Note 1: The ADC conversion result never decreases with an increase in the input voltage, and has no missing

codes.

2: Injection currents > | 0 | can affect the ADC results by approximately 4-6 counts.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-43: ADC MODULE SPECIFICATIONS (10-BIT MODE)(2)

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤ TA ≤ +125°C for Extended

Param

No. Symbol Characteristic Min. Typ Max. Units Conditions

ADC Accuracy (10-bit Mode) - Measurements with external VREF+/VREF-

AD20b Nr Resolution 10 data bits bits

AD21b INL Integral Nonlinearity -1.5 — +1.5 LSb VINL = AVSS = VREFL =

0V, AVDD = VREFH = 3.6V

AD22b DNL Differential Nonlinearity >-1 — <1 LSb VINL = AVSS = VREFL =

0V, AVDD = VREFH = 3.6V

AD23b GERR Gain Error — 3 6 LSb VINL = AVSS = VREFL =

0V, AVDD = VREFH = 3.6V

AD24b EOFF Offset Error — 2 5 LSb VINL = AVSS = VREFL =

0V, AVDD = VREFH = 3.6V

AD25b — Monotonicity(1) — — — — Guaranteed

ADC Accuracy (10-bit Mode) - Measurements with internal VREF+/VREF-

AD20b Nr Resolution 10 data bits bits

AD21b INL Integral Nonlinearity -1 — +1 LSb VINL = AVSS = VREFL =

0V, AVDD = VREFH = 3.6V

AD22b DNL Differential Nonlinearity >-1 — <1 LSb VINL = AVSS = VREFL =

0V, AVDD = VREFH = 3.6V

AD23b GERR Gain Error — 7 15 LSb VINL = AVSS = VREFL =

0V, AVDD = VREFH = 3.6V

AD24b EOFF Offset Error — 3 7 LSb VINL = AVSS = VREFL =

0V, AVDD = VREFH = 3.6V

AD25b — Monotonicity(1) — — — — Guaranteed

Dynamic Performance (10-bit Mode)

AD30b THD Total Harmonic Distortion — — -64 dB —

AD31b SINAD Signal to Noise and

Distortion

57 58.5 — dB —

AD32b SFDR Spurious Free Dynamic

Range

72 — — dB —

AD33b FNYQ Input Signal Bandwidth — — 550 kHz —

AD34b ENOB Effective Number of Bits 9.16 9.4 — bits —

Note 1: The ADC conversion result never decreases with an increase in the input voltage, and has no missing

codes.

2: Injection currents > | 0 | can affect the ADC results by approximately 4-6 counts.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 25-24: ADC CONVERSION (12-BIT MODE) TIMING CHARACTERISTICS

(ASAM = 0, SSRC<2:0> = 000)

AD55

TSAMP

Clear SAMPSet SAMP

AD61

ADCLK

Instruction

SAMP

ch0_dischrg

ch0_samp

AD60

CONV

ADxIF

Buffer(0)

1 2 3 4 5 6 87

1– Software sets ADxCON. SAMP to start sampling.

2– Sampling starts after discharge period. TSAMP is described

3– Software clears ADxCON. SAMP to start conversion.

4– Sampling ends, conversion sequence starts.

5– Convert bit 11.

9– One TAD for end of conversion.

AD50

eoc

6– Convert bit 10.

7– Convert bit 1.

8– Convert bit 0.

Execution

in Section 16. “Analog-to-Digital Converter (ADC) with DMA”

(DS70183) in the “dsPIC33F/PIC24H Family Reference Manual”.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-44: ADC CONVERSION (12-BIT MODE) TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤ TA ≤ +125°C for Extended

Param

No. Symbol Characteristic Min. Typ(1) Max. Units Conditions

Clock Parameters

AD50a TAD ADC Clock Period 117.6 — — ns —

AD51a tRC ADC Internal RC Oscillator

Period

— 250 — ns —

Conversion Rate

AD55a tCONV Conversion Time — 14 TAD ns —

AD56a FCNV Throughput Rate — — 500 ksps —

AD57a tSAMP Sample Time 3 TAD —— — —

Timing Parameters

AD60a tPCS Conversion Start from Sample

Trigger(2)

2.0 TAD — 3.0 TAD — Auto-Convert Trigger

(SSRC<2:0> = 111) not

selected

AD61a tPSS Sample Start from Setting

Sample (SAMP) bit(2)

2.0 TAD — 3.0 TAD ——

AD62a tCSS Conversion Completion to

Sample Start (ASAM = 1)(2)

— 0.5 TAD —— —

AD63a tDPU Time to Stabilize Analog Stage

from ADC Off to ADC On(2,3)

——20μs—

Note 1: These parameters are characterized but not tested in manufacturing.

2: Because the sample caps will eventually lose charge, clock rates below 10 kHz can affect linearity

performance, especially at elevated temperatures.

3: tDPU is the time required for the ADC module to stabilize when it is turned on (AD1CON1<ADON> = 1).

During this time, the ADC result is indeterminate.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 25-25: ADC CONVERSION (10-BIT MODE) TIMING CHARACTERISTICS

(CHPS<1:0> = 01, SIMSAM = 0, ASAM = 0, SSRC<2:0> = 000)

AD55

TSAMP

Clear SAMPSet SAMP

AD61

ADCLK

Instruction

SAMP

ch0_dischrg

ch1_samp

AD60

CONV

ADxIF

Buffer(0)

Buffer(1)

1 2 3 4 5 6 8 5 6 7

1– Software sets ADxCON. SAMP to start sampling.

2– Sampling starts after discharge period. TSAMP is described in Section 16. “Analog-to-Digital Converter (ADC)”

3– Software clears ADxCON. SAMP to start conversion.

4– Sampling ends, conversion sequence starts.

5– Convert bit 9.

8– One TAD for end of conversion.

AD50

ch0_samp

ch1_dischrg

eoc

AD55

6– Convert bit 8.

7– Convert bit 0.

Execution

(DS70183) in the “dsPIC33F/PIC24H Family Reference Manual”.

dsPIC33FJXXXGPX06A/X08A/X10A

FIGURE 25-26: ADC CONVERSION (10-BIT MODE) TIMING CHARACTERISTICS (CHPS<1:0> = 01,

SIMSAM = 0, ASAM = 1, SSRC<2:0> = 111, SAMC<4:0> = 00001)

AD55

TSAMP

Set ADON

ADCLK

Instruction

SAMP

ch0_dischrg

ch1_samp

CONV

ADxIF

Buffer(0)

Buffer(1)

1 2 3 4 5 6 4 5 6 8

1– Software sets ADxCON. ADON to start AD operation.

2– Sampling starts after discharge period.

3– Convert bit 9.

4– Convert bit 8.

5– Convert bit 0.

AD50

ch0_samp

ch1_dischrg

eoc

7 3

AD55

6– One TAD for end of conversion.

7– Begin conversion of next channel.

8– Sample for time specified by SAMC<4:0>.

TSAMP

TCONV

3 4

Execution

TSAMP is described in Section 16. “Analog-to-Digital Converter

(ADC)” (DS70183) in the “dsPIC33F/PIC24H Family Reference Manual”.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 25-46: DMA READ/WRITE TIMING REQUIREMENTS

TABLE 25-45: ADC CONVERSION (10-BIT MODE) TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤ TA ≤ +125°C for Extended

Param

No. Symbol Characteristic Min. Typ(1) Max. Units Conditions

Clock Parameters

AD50b TAD ADC Clock Period 65 — — ns —

AD51b TRC ADC Internal RC Oscillator Period — 250 — ns —

Conversion Rate

AD55b TCONV Conversion Time — 12 TAD —— —

AD56b FCNV Throughput Rate — — 1.1 Msps —

AD57b TSAMP Sample Time 2 TAD ——— —

Timing Parameters

AD60b TPCS Conversion Start from Sample

Trigger(2)

2.0 TAD — 3.0 TAD — Auto-Convert Trigger

(SSRC<2:0> = 111) not

selected

AD61b TPSS Sample Start from Setting

Sample (SAMP) bit(2)

2.0 TAD — 3.0 TAD ——

AD62b TCSS Conversion Completion to

Sample Start (ASAM = 1)(2)

— 0.5 TAD —— —

AD63b TDPU Time to Stabilize Analog Stage

from ADC Off to ADC On(2,3)

——20 μs—

Note 1: These parameters are characterized but not tested in manufacturing.

2: Because the sample caps will eventually lose charge, clock rates below 10 kHz can affect linearity

performance, especially at elevated temperatures.

3: TDPU is the time required for the ADC module to stabilize when it is turned on (AD1CON1<ADON> = 1).

During this time, the ADC result is indeterminate.

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C ≤TA ≤+125°C for Extended

Param

No. Characteristic Min. Typ Max. Units Conditions

DM1a DMA Read/Write Cycle Time — — 2 TCY ns This characteristic applies to

dsPIC33FJ256GPX06A/X08A/X10A

devices only.

DM1b DMA Read/Write Cycle Time — — 1 TCY ns This characteristic applies to all

devices with the exception of the

dsPIC33FJ256GPX06A/X08A/X10A.

dsPIC33FJXXXGPX06A/X08A/X10A

26.0 HIGH TEMPERATURE ELECTRICAL CHARACTERISTICS

This section provides an overview of dsPIC33FJXXXGPX06A/X08A/X10A electrical characteristics for devices

operating in an ambient temperature range of -40°C to +150°C.

The specifications between -40°C to +150°C are identical to those shown in Section 25.0 “Electrical Characteristics”

for operation between -40°C to +125°C, with the exception of the parameters listed in this section.

Parameters in this section begin with an H, which denotes High temperature. For example, parameter DC10 in

Section 25.0 “Electrical Characteristics” is the Industrial and Extended temperature equivalent of HDC10.

Absolute maximum ratings for the dsPIC33FJXXXGPX06A/X08A/X10A high temperature devices are listed below.

Exposure to these maximum rating conditions for extended periods can affect device reliability. Functional operation of

the device at these or any other conditions above the parameters indicated in the operation listings of this specification

is not implied.

Absolute Maximum Ratings(1)

Ambient temperature under bias(4) .........................................................................................................-40°C to +150°C

Storage temperature .............................................................................................................................. -65°C to +160°C

Voltage on VDD with respect to VSS ......................................................................................................... -0.3V to +4.0V

Voltage on any pin that is not 5V tolerant with respect to VSS(5) .................................................... -0.3V to (VDD + 0.3V)

Voltage on any 5V tolerant pin with respect to VSS when VDD < 3.0V(5) ....................................... -0.3V to (VDD + 0.3V)

Voltage on any 5V tolerant pin with respect to VSS when VDD ≥ 3.0V(5) .................................................... -0.3V to 5.6V

Voltage on VCAP with respect to VSS ...................................................................................................... 2.25V to 2.75V

Maximum current out of VSS pin .............................................................................................................................60 mA

Maximum current into VDD pin(2).............................................................................................................................60 mA

Maximum junction temperature............................................................................................................................. +155°C

Maximum output current sunk by any I/O pin(3) ........................................................................................................1 mA

Maximum output current sourced by any I/O pin(3)...................................................................................................1 mA

Maximum current sunk by all ports combined ........................................................................................................10 mA

Maximum current sourced by all ports combined(2) ................................................................................................10 mA

Note: Programming of the Flash memory is not allowed above 125°C.

Note 1: Stresses above those listed under “Absolute Maximum Ratings” can cause permanent damage to the

device. This is a stress rating only, and functional operation of the device at those or any other conditions

above those indicated in the operation listings of this specification is not implied. Exposure to maximum

rating conditions for extended periods can affect device reliability.

2: Maximum allowable current is a function of device maximum power dissipation (see Table 26-2).

3: Unlike devices at 125°C and below, the specifications in this section also apply to the CLKOUT, VREF+,

VREF-, SCLx, SDAx, PGECx, and PGEDx pins.

4: AEC-Q100 reliability testing for devices intended to operate at 150°C is 1,000 hours. Any design in which

the total operating time from 125°C to 150°C will be greater than 1,000 hours is not warranted without prior

written approval from Microchip Technology Inc.

5: Refer to the “Pin Diagrams” section for 5V tolerant pins.

dsPIC33FJXXXGPX06A/X08A/X10A

26.1 High Temperature DC Characteristics

TABLE 26-1: OPERATING MIPS VS. VOLTAGE

TABLE 26-2: THERMAL OPERATING CONDITIONS

TABLE 26-3: DC TEMPERATURE AND VOLTAGE SPECIFICATIONS

TABLE 26-4: DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD)

Characteristic VDD Range

(in Volts)

Temperature Range

(in °C)

Max MIPS

dsPIC33FJXXXGPX06A/X08A/X10A

3.0V to 3.6V -40°C to +150°C 20

Rating Symbol Min Typ Max Unit

High Temperature Devices

Operating Junction Temperature Range TJ-40 — +155 °C

Operating Ambient Temperature Range TA-40 — +150 °C

Power Dissipation:

Internal chip power dissipation:

PINT = VDD x (IDD - Σ IOH) PDPINT + PI/OW

I/O Pin Power Dissipation:

I/O = Σ ({VDD - VOH} x IOH) + Σ (VOL x IOL)

Maximum Allowed Power Dissipation PDMAX (TJ - TA)/θJA W

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +150°C for High Temperature

Parameter

No. Symbol Characteristic Min Typ Max Units Conditions

Operating Voltage

HDC10 Supply Voltage

VDD — 3.0 3.3 3.6 V -40°C to +150°C

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +150°C for High Temperature

Parameter

No. Typical Max Units Conditions

Power-Down Current (IPD)

HDC60e 250 2000 μA +150°C 3.3V Base Power-Down Current(1,3)

HDC61c 3 5 μA +150°C 3.3V Watchdog Timer Current: ΔIWDT(2,4)

Note 1: Base IPD is measured with all peripherals and clocks shut down. All I/Os are configured as inputs and

pulled to VSS. WDT, etc., are all switched off, and VREGS (RCON<8>) = 1.

2: The Δ current is the additional current consumed when the module is enabled. This current should be

added to the base IPD current.

3: These currents are measured on the device containing the most memory in this family.

4: These parameters are characterized, but are not tested in manufacturing.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 26-5: DC CHARACTERISTICS: DOZE CURRENT (IDOZE)

TABLE 26-6: DC CHARACTERISTICS: I/O PIN OUTPUT SPECIFICATIONS

TABLE 26-7: DC CHARACTERISTICS: PROGRAM MEMORY

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +150°C for High Temperature

Parameter

No. Typical(1) Max Doze

Ratio Units Conditions

HDC72a 39 45 1:2 mA

+150°C 3.3V 20 MIPSHDC72f 18 25 1:64 mA

HDC72g 18 25 1:128 mA

Note 1: Parameters with Doze ratios of 1:2 and 1:64 are characterized, but are not tested in manufacturing.

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +150°C for High Temperature

Param

No. Symbol Characteristic Min Typ Max Units Conditions

VOL Output Low Voltage

HDO10 I/O ports — — 0.4 V IOL = 1 mA, VDD = 3.3V

HDO16 OSC2/CLKO — — 0.4 V IOL = 1 mA, VDD = 3.3V

VOH Output High Voltage

HDO20 I/O ports 2.40 — — V IOH = -1 mA, VDD = 3.3V

HDO26 OSC2/CLKO 2.41 — — V IOH = -1 mA, VDD = 3.3V

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +150°C for High Temperature

Param

No. Symbol Characteristic(1) Min Typ Max Units Conditions

Program Flash Memory

HD130 EPCell Endurance 10,000 — — E/W -40°C to +150°C(2)

HD134 TRETD Characteristic Retention 20 — — Year 1000 E/W cycles or less and no

other specifications are violated

Note 1: These parameters are assured by design, but are not characterized or tested in manufacturing.

2: Programming of the Flash memory is not allowed above 125°C.

dsPIC33FJXXXGPX06A/X08A/X10A

26.2 AC Characteristics and Timing

Parameters

The information contained in this section defines

dsPIC33FJXXXGPX06A/X08A/X10A AC

characteristics and timing parameters for high

temperature devices. However, all AC timing

specifications in this section are the same as those in

Section 25.2 “AC Characteristics and Timing

Parameters”, with the exception of the parameters

listed in this section.

Parameters in this section begin with an H, which

denotes High temperature. For example, parameter

OS53 in Section 25.2 “AC Characteristics and

Timing Parameters” is the Industrial and Extended

temperature equivalent of HOS53.

TABLE 26-8: TEMPERATURE AND VOLTAGE SPECIFICATIONS – AC

FIGURE 26-1: LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS

TABLE 26-9: PLL CLOCK TIMING SPECIFICATIONS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +150°C for High Temperature

Operating voltage VDD range as described in Table 26-1.

VDD/2

VSS

RL=464Ω

CL= 50 pF for all pins except OSC2

15 pF for OSC2 output

Load Condition 1 – for all pins except OSC2 Load Condition 2 – for OSC2

CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +150°C for High Temperature

Param

No. Symbol Characteristic Min Typ Max Units Conditions

HOS53 DCLK CLKO Stability (Jitter)(1) -5 0.5 5 % Measured over 100 ms

period

Note 1: These parameters are characterized, but are not tested in manufacturing.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 26-10: INTERNAL LPRC ACCURACY

TABLE 26-11: SPIx MASTER MODE (CKE = 0) TIMING REQUIREMENTS

TABLE 26-12: SPIx MODULE MASTER MODE (CKE = 1) TIMING REQUIREMENTS

CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +150°C for High Temperature

Param

No. Characteristic Min Typ Max Units Conditions

LPRC @ 32.768 kHz (1)

HF21 LPRC -70(2) —+70

(2) % -40°C ≤ TA ≤ +150°C

Note 1: Change of LPRC frequency as VDD changes.

2: Characterized but not tested.

CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +150°C for High Temperature

Param

No. Symbol Characteristic(1) Min Typ Max Units Conditions

HSP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

—1025ns —

HSP40 TdiV2scH,

TdiV2scL

Setup Time of SDIx Data Input

to SCKx Edge

28 — — ns —

HSP41 TscH2diL,

TscL2diL

Hold Time of SDIx Data Input

to SCKx Edge

35 — — ns —

Note 1: These parameters are characterized but not tested in manufacturing.

CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +150°C for High Temperature

Param

No. Symbol Characteristic(1) Min Typ Max Units Conditions

HSP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

—1025ns —

HSP36 TdoV2sc,

TdoV2scL

SDOx Data Output Setup to

First SCKx Edge

35 — — ns —

HSP40 TdiV2scH,

TdiV2scL

Setup Time of SDIx Data Input

to SCKx Edge

28 — — ns —

HSP41 TscH2diL,

TscL2diL

Hold Time of SDIx Data Input

to SCKx Edge

35 — — ns —

Note 1: These parameters are characterized but not tested in manufacturing.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 26-13: SPIx MODULE SLAVE MODE (CKE = 0) TIMING REQUIREMENTS

TABLE 26-14: SPIx MODULE SLAVE MODE (CKE = 1) TIMING REQUIREMENTS

CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +150°C for High Temperature

Param

No. Symbol Characteristic(1) Min Typ Max Units Conditions

HSP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

——35ns —

HSP40 TdiV2scH,

TdiV2scL

Setup Time of SDIx Data Input

to SCKx Edge

25 — — ns —

HSP41 TscH2diL,

TscL2diL

Hold Time of SDIx Data Input to

SCKx Edge

25 — — ns —

HSP51 TssH2doZ SSx ↑ to SDOx Output

High-Impedance

15 — 55 ns See Note 2

Note 1: These parameters are characterized but not tested in manufacturing.

2: Assumes 50 pF load on all SPIx pins.

CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +150°C for High Temperature

Param

No. Symbol Characteristic(1) Min Typ Max Units Conditions

HSP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

— — 35 ns —

HSP40 TdiV2scH,

TdiV2scL

Setup Time of SDIx Data Input

to SCKx Edge

25 — — ns —

HSP41 TscH2diL,

TscL2diL

Hold Time of SDIx Data Input

to SCKx Edge

25 — — ns —

HSP51 TssH2doZ SSx ↑ to SDOX Output

High-Impedance

15 — 55 ns See Note 2

HSP60 TssL2doV SDOx Data Output Valid after

SSx Edge

— — 55 ns —

Note 1: These parameters are characterized but not tested in manufacturing.

2: Assumes 50 pF load on all SPIx pins.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 26-15: ADC MODULE SPECIFICATIONS

TABLE 26-16: ADC MODULE SPECIFICATIONS (12-BIT MODE)(3)

TABLE 26-17: ADC MODULE SPECIFICATIONS (10-BIT MODE)(3)

CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +150°C for High Temperature

Param

No. Symbol Characteristic Min Typ Max Units Conditions

Reference Inputs

HAD08 IREF Current Drain —

—

250

—

600

μA

ADC operating, See Note 1

ADC off, See Note 1

Note 1: These parameters are not characterized or tested in manufacturing.

2: These parameters are characterized, but are not tested in manufacturing.

CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +150°C for High Temperature

Param

No. Symbol Characteristic Min Typ Max Units Conditions

ADC Accuracy (12-bit Mode) – Measurements with external VREF+/VREF-(1)

AD23a GERR Gain Error — 5 10 LSb VINL = AVSS = VREFL = 0V,

AVDD = VREFH = 3.6V

AD24a EOFF Offset Error — 2 5 LSb VINL = AVSS = VREFL = 0V,

AVDD = VREFH = 3.6V

ADC Accuracy (12-bit Mode) – Measurements with internal VREF+/VREF-(1)

AD23a GERR Gain Error 2 10 20 LSb VINL = AVSS = 0V, AVDD = 3.6V

AD24a EOFF Offset Error 2 5 10 LSb VINL = AVSS = 0V, AVDD = 3.6V

Dynamic Performance (12-bit Mode)(2)

HAD33a FNYQ Input Signal Bandwidth — — 200 kHz —

Note 1: These parameters are characterized, but are tested at 20 ksps only.

2: These parameters are characterized by similarity, but are not tested in manufacturing.

3: Injection currents > | 0 | can affect the ADC results by approximately 4-6 counts.

CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +150°C for High Temperature

Param

No. Symbol Characteristic Min Typ Max Units Conditions

ADC Accuracy (12-bit Mode) – Measurements with external VREF+/VREF-(1)

AD23b GERR Gain Error — 3 6 LSb VINL = AVSS = VREFL = 0V,

AVDD = VREFH = 3.6V

AD24b EOFF Offset Error — 2 5 LSb VINL = AVSS = VREFL = 0V,

AVDD = VREFH = 3.6V

ADC Accuracy (12-bit Mode) – Measurements with internal VREF+/VREF-(1)

AD23b GERR Gain Error — 7 15 LSb VINL = AVSS = 0V, AVDD = 3.6V

AD24b EOFF Offset Error — 3 7 LSb VINL = AVSS = 0V, AVDD = 3.6V

Dynamic Performance (10-bit Mode)(2)

HAD33b FNYQ Input Signal Bandwidth — — 400 kHz —

Note 1: These parameters are characterized, but are tested at 20 ksps only.

2: These parameters are characterized by similarity, but are not tested in manufacturing.

3: Injection currents > | 0 | can affect the ADC results by approximately 4-6 counts.

dsPIC33FJXXXGPX06A/X08A/X10A

TABLE 26-18: ADC CONVERSION (12-BIT MODE) TIMING REQUIREMENTS

TABLE 26-19: ADC CONVERSION (10-BIT MODE) TIMING REQUIREMENTS

CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +150°C for High Temperature

Param

No. Symbol Characteristic Min Typ Max Units Conditions

Clock Parameters

HAD50 TAD ADC Clock Period(1) 147 — — ns —

Conversion Rate

HAD56 FCNV Throughput Rate(1) — — 400 Ksps —

Note 1: These parameters are characterized but not tested in manufacturing.

CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +150°C for High Temperature

Param

No. Symbol Characteristic Min Typ Max Units Conditions

Clock Parameters

HAD50 TAD ADC Clock Period(1) 104 — — ns —

Conversion Rate

HAD56 FCNV Throughput Rate(1) ——800Ksps —

Note 1: These parameters are characterized but not tested in manufacturing.

dsPIC33FJXXXGPX06A/X08A/X10A

27.0 PACKAGING INFORMATION

27.1 Package Marking Information

64-Lead TQFP (10x10x1 mm)

XXXXXXXXXX

YYWWNNN

Example

dsPIC33FJ

256GP706A

0510017

80-Lead TQFP (12x12x1 mm)

XXXXXXXXXXXX

YYWWNNN

Example

dsPIC33FJ128

0510017

Legend: XX...X Customer-specific information

Y Year code (last digit of calendar year)

YY Year code (last 2 digits of calendar year)

WW Week code (week of January 1 is week ‘01’)

NNN Alphanumeric traceability code

Pb-free JEDEC designator for Matte Tin (Sn)

*This package is Pb-free. The Pb-free JEDEC designator ( )

can be found on the outer packaging for this package.

Note: In the event the full Microchip part number cannot be marked on one line, it will

be carried over to the next line, thus limiting the number of available

characters for customer-specific information.

GP708A-I/PT

-I/PT

64-Lead QFN (9x9x0.9mm) Example

XXXXXXXXXX

YYWWNNN

33FJ64GP

206A-I/MR

0610017

dsPIC33FJXXXGPX06A/X08A/X10A

27.1 Package Marking Information (Continued)

Legend: XX...X Customer-specific information

Y Year code (last digit of calendar year)

YY Year code (last 2 digits of calendar year)

WW Week code (week of January 1 is week ‘01’)

NNN Alphanumeric traceability code

Pb-free JEDEC designator for Matte Tin (Sn)

*This package is Pb-free. The Pb-free JEDEC designator ( )

can be found on the outer packaging for this package.

Note: In the event the full Microchip part number cannot be marked on one line, it will

be carried over to the next line, thus limiting the number of available

characters for customer-specific information.

100-Lead TQFP (12x12x1 mm)

XXXXXXXXXXXX

YYWWNNN

Example

dsPIC33FJ256

GP710A-I/PT

0510017

100-Lead TQFP (14x14x1mm)

XXXXXXXXXXXX

YYWWNNN

Example

dsPIC33FJ256

GP710A-I/PF

0510017

dsPIC33FJXXXGPX06A/X08A/X10A

27.2 Package Details

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

dsPIC33FJXXXGPX06A/X08A/X10A

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

dsPIC33FJXXXGPX06A/X08A/X10A

64-Lead Plastic Thin Quad Flatpack (PT) – 10x10x1 mm Body, 2.00 mm Footprint [TQFP]

Notes:

1. Pin 1 visual index feature may vary, but must be located within the hatched area.

2. Chamfers at corners are optional; size may vary.

3. Dimensions D1 and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.25 mm per side.

4. Dimensioning and tolerancing per ASME Y14.5M.

BSC: Basic Dimension. Theoretically exact value shown without tolerances.

REF: Reference Dimension, usually without tolerance, for information purposes only.

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

Units MILLIMETERS

Dimension Limits MIN NOM MAX

Number of Leads N 64

Lead Pitch e 0.50 BSC

Overall Height A – – 1.20

Molded Package Thickness A2 0.95 1.00 1.05

Standoff A1 0.05 – 0.15

Foot Length L 0.45 0.60 0.75

Footprint L1 1.00 REF

Foot Angle φ0° 3.5° 7°

Overall Width E 12.00 BSC

Overall Length D 12.00 BSC

Molded Package Width E1 10.00 BSC

Molded Package Length D1 10.00 BSC

Lead Thickness c 0.09 – 0.20

Lead Width b 0.17 0.22 0.27

Mold Draft Angle Top α11° 12° 13°

Mold Draft Angle Bottom β11° 12° 13°

NOTE 1123 NOTE 2

Microchip Technology Drawing C04-085B

dsPIC33FJXXXGPX06A/X08A/X10A

/HDG3ODVWLF7KLQ4XDG)ODWSDFN37±[[PP%RG\PP>74)3@

1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW

KWWSZZZPLFURFKLSFRPSDFNDJLQJ

dsPIC33FJXXXGPX06A/X08A/X10A

80-Lead Plastic Thin Quad Flatpack (PT) – 12x12x1 mm Body, 2.00 mm Footprint [TQFP]

Notes:

1. Pin 1 visual index feature may vary, but must be located within the hatched area.

2. Chamfers at corners are optional; size may vary.

3. Dimensions D1 and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.25 mm per side.

4. Dimensioning and tolerancing per ASME Y14.5M.

BSC: Basic Dimension. Theoretically exact value shown without tolerances.

REF: Reference Dimension, usually without tolerance, for information purposes only.

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

Units MILLIMETERS

Dimension Limits MIN NOM MAX

Number of Leads N 80

Lead Pitch e 0.50 BSC

Overall Height A – – 1.20

Molded Package Thickness A2 0.95 1.00 1.05

Standoff A1 0.05 – 0.15

Foot Length L 0.45 0.60 0.75

Footprint L1 1.00 REF

Foot Angle φ0° 3.5° 7°

Overall Width E 14.00 BSC

Overall Length D 14.00 BSC

Molded Package Width E1 12.00 BSC

Molded Package Length D1 12.00 BSC

Lead Thickness c 0.09 – 0.20

Lead Width b 0.17 0.22 0.27

Mold Draft Angle Top α11° 12° 13°

Mold Draft Angle Bottom β11° 12° 13°

NOTE 1123 NOTE 2

βφ

Microchip Technology Drawing C04-092B

dsPIC33FJXXXGPX06A/X08A/X10A

/HDG3ODVWLF7KLQ4XDG)ODWSDFN37±[[PP%RG\PP>74)3@

1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW

KWWSZZZPLFURFKLSFRPSDFNDJLQJ

dsPIC33FJXXXGPX06A/X08A/X10A

100-Lead Plastic Thin Quad Flatpack (PT) – 12x12x1 mm Body, 2.00 mm Footprint [TQFP]

Notes:

1. Pin 1 visual index feature may vary, but must be located within the hatched area.

2. Chamfers at corners are optional; size may vary.

3. Dimensions D1 and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.25 mm per side.

4. Dimensioning and tolerancing per ASME Y14.5M.

BSC: Basic Dimension. Theoretically exact value shown without tolerances.

REF: Reference Dimension, usually without tolerance, for information purposes only.

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

Units MILLIMETERS

Dimension Limits MIN NOM MAX

Number of Leads N 100

Lead Pitch e 0.40 BSC

Overall Height A – – 1.20

Molded Package Thickness A2 0.95 1.00 1.05

Standoff A1 0.05 – 0.15

Foot Length L 0.45 0.60 0.75

Footprint L1 1.00 REF

Foot Angle φ0° 3.5° 7°

Overall Width E 14.00 BSC

Overall Length D 14.00 BSC

Molded Package Width E1 12.00 BSC

Molded Package Length D1 12.00 BSC

Lead Thickness c 0.09 – 0.20

Lead Width b 0.13 0.18 0.23

Mold Draft Angle Top α11° 12° 13°

Mold Draft Angle Bottom β11° 12° 13°

123

NOTE 1NOTE 2

A1 L1

Microchip Technology Drawing C04-100B

dsPIC33FJXXXGPX06A/X08A/X10A

/HDG3ODVWLF7KLQ4XDG)ODWSDFN37±[[PP%RG\PP>74)3@

1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW

KWWSZZZPLFURFKLSFRPSDFNDJLQJ

dsPIC33FJXXXGPX06A/X08A/X10A

100-Lead Plastic Thin Quad Flatpack (PF) – 14x14x1 mm Body, 2.00 mm Footprint [TQFP]

Notes:

1. Pin 1 visual index feature may vary, but must be located within the hatched area.

2. Chamfers at corners are optional; size may vary.

3. Dimensions D1 and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.25 mm per side.

4. Dimensioning and tolerancing per ASME Y14.5M.

BSC: Basic Dimension. Theoretically exact value shown without tolerances.

REF: Reference Dimension, usually without tolerance, for information purposes only.

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

Units MILLIMETERS

Dimension Limits MIN NOM MAX

Number of Leads N 100

Lead Pitch e 0.50 BSC

Overall Height A – – 1.20

Molded Package Thickness A2 0.95 1.00 1.05

Standoff A1 0.05 – 0.15

Foot Length L 0.45 0.60 0.75

Footprint L1 1.00 REF

Foot Angle φ0° 3.5° 7°

Overall Width E 16.00 BSC

Overall Length D 16.00 BSC

Molded Package Width E1 14.00 BSC

Molded Package Length D1 14.00 BSC

Lead Thickness c 0.09 – 0.20

Lead Width b 0.17 0.22 0.27

Mold Draft Angle Top α11° 12° 13°

Mold Draft Angle Bottom β11° 12° 13°

NOTE 1NOTE 2

123

LA1 L1

Microchip Technology Drawing C04-110B

dsPIC33FJXXXGPX06A/X08A/X10A

/HDG3ODVWLF7KLQ4XDG)ODWSDFN3)±[[PP%RG\PP>74)3@

1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW

KWWSZZZPLFURFKLSFRPSDFNDJLQJ

dsPIC33FJXXXGPX06A/X08A/X10A

APPENDIX A: MIGRATING FROM

dsPIC33FJXXXGPX06/

X08/X10 DEVICES TO

dsPIC33FJXXXGPX06A

/X08A/X10A DEVICES

dsPIC33FJXXXGPX06A/X08A/X10A devices were

designed to enhance the dsPIC33FJXXXGPX06/X08/

X10 families of devices.

In general, the dsPIC33FJXXXGPX06A/X08A/X10A

devices are backward-compatible with

dsPIC33FJXXXGPX06/X08/X10 devices; however,

manufacturing differences may cause

dsPIC33FJXXXGPX06A/X08A/X10A devices to

behave differently from dsPIC33FJXXXGPX06/X08/

X10 devices. Therefore, complete system test and

characterization is recommended if

dsPIC33FJXXXGPX06A/X08A/X10A devices are used

to replace dsPIC33FJXXXGPX06/X08/X10 devices.

The following enhancements were introduced:

• Extended temperature support of up to +125ºC

• Enhanced Flash module with higher endurance

and retention

• New PLL Lock Enable configuration bit

• Added Timer5 trigger for ADC1 and Timer3 trigger

for ADC2

dsPIC33FJXXXGPX06A/X08A/X10A

APPENDIX B: REVISION HISTORY

Revision A (April 2009)

This is the initial release of this document.

Revision B (October 2009)

The revision includes the following global update:

• Added Note 2 to the shaded table that appears at

the beginning of each chapter. This new note

provides information regarding the availability of

registers and their associated bits

This revision also includes minor typographical and

formatting changes throughout the data sheet text.

All other major changes are referenced by their

respective section in the following table.

TABLE B-1: MAJOR SECTION UPDATES

Section Name Update Description

“High-Performance, 16-Bit Digital Signal

Controllers”

Added information on high temperature operation (see “Operating

Range”).

Section 10.0 “Power-Saving Features” Updated the last paragraph to clarify the number of cycles that occur

prior to the start of instruction execution (see Section 10.2.2 “Idle

Mode”).

Section 11.0 “I/O Ports” Changed the reference to digital-only pins to 5V tolerant pins in the

second paragraph of Section 11.2 “Open-Drain Configuration”.

Section 18.0 “Universal Asynchronous

Receiver Transmitter (UART)”

Updated the two baud rate range features to: 10 Mbps to 38 bps at

40 MIPS.

Section 21.0 “10-Bit/12-Bit

Analog-to-Digital Converter (ADC)”

Updated the ADCx block diagram (see Figure 21-1).

Section 22.0 “Special Features” Updated the second paragraph and removed the fourth paragraph in

Section 22.1 “Configuration Bits”.

Updated the Device Configuration Register Map (see Table 22-1).

Added the FPWRT<2:0> bit field for the FWDT register to the

Configurative Bits Description table (see Table 22-1).

Section 25.0 “Electrical Characteristics” Updated the Absolute Maximum Ratings for high temperature and

added Note 4.

Updated Power-Down Current parameters DC60d, DC60a, DC60b,

and DC60d (see Table 25-7).

Added I2Cx Bus Data Timing Requirements (Master Mode)

parameter IM51 (see Table 25-36).

Updated the SPIx Module Slave Mode (CKE = 1) Timing

Characteristics (see Figure 25-12).

Updated the Internal LPRC Accuracy parameters (see Table 25-19).

Updated the ADC Module Specifications (12-bit Mode) parameters

AD23a and AD24a (see Table 25-42).

Updated the ADC Module Specifications (10-bit Mode) parameters

AD23b and AD24b (see Table 25-43).

Section 26.0 “High Temperature Electrical

Characteristics”

Added new chapter with high temperature specifications.

“Product Identification System” Added the “H” definition for high temperature.

dsPIC33FJXXXGPX06A/X08A/X10A

Revision C (March 2011)

This revision includes typographical and formatting

changes throughout the data sheet text. In addition, all

instances of VDDCORE have been removed.

All other major changes are referenced by their

respective section in the following table.

TABLE B-2: MAJOR SECTION UPDATES

Section Name Update Description

Section 2.0 “Guidelines for Getting Started

with 16-Bit Digital Signal Controllers”

Updated the title of Section 2.3 “CPU Logic Filter Capacitor

Connection (Vcap)”.

The frequency limitation for device PLL start-up conditions was

updated in Section 2.7 “Oscillator Value Conditions on Device

Start-up”.

The second paragraph in Section 2.9 “Unused I/Os” was updated.

Section 4.0 “Memory Organization” The All Resets values for the following SFRs in the Timer Register

Map were changed (see Ta b l e 4 - 6 ):

•TMR1

•TMR2

•TMR3

•TMR4

•TMR5

•TMR6

•TMR7

•TMR8

•TMR9

Section 9.0 “Oscillator Configuration” Added Note 3 to the OSCCON: Oscillator Control Register (see

Added Note 2 to the CLKDIV: Clock Divisor Register (see

Added Note 1 to the PLLFBD: PLL Feedback Divisor Register (see

Added Note 2 to the OSCTUN: FRC Oscillator Tuning Register (see

Section 21.0 “10-Bit/12-Bit

Analog-to-Digital Converter (ADC)”

Updated the VREFL references in the ADC1 module block diagram

(see Figure 21-1).

Section 22.0 “Special Features” Added a new paragraph and removed the third paragraph in

Section 22.1 “Configuration Bits”.

Added the column “RTSP Effects” to the Configuration Bits

Descriptions (see Table 22-2).

dsPIC33FJXXXGPX06A/X08A/X10A

Section 25.0 “Electrical Characteristics” Removed Note 4 from the DC Temperature and Voltage

Specifications (see Tab l e 2 5 - 4).

Updated the maximum value for parameter DI19 and added

parameters DI28, DI29, DI60a, DI60b, and DI60c to the I/O Pin Input

Specifications (see Tab l e 2 5 - 9).

Removed Note 2 from the AC Characteristics: Internal RC Accuracy

(see Table 25-18).

Updated the characteristic description for parameter DI35 in the I/O

Timing Requirements (see Table 25-20).

Updated the ADC Module Specification minimum values for

parameters AD05 and AD07, and updated the maximum value for

parameter AD06 (see Table 25-41).

Added Note 1 to the ADC Module Specifications (12-bit Mode) (see

Table 25-42).

Added Note 1 to the ADC Module Specifications (10-bit Mode) (see

Table 25-43).

Added DMA Read/Write Timing Requirements (see Table 25-46).

Section 26.0 “High Temperature Electrical

Characteristics”

Updated all ambient temperature end range values to +150ºC

throughout the chapter.

Updated the storage temperature end range to +160ºC.

Updated the maximum junction temperature from +145ºC to +155ºC.

Updated the maximum values for High Temperature Devices in the

Thermal Operating Conditions (see Ta b l e 2 6 - 2 ).

Added Note 3 and updated the ADC Module Specifications (12-bit

Mode), removing all parameters with the exception of HAD33a (see

Table 26-16).

Added Note 3 and updated the ADC Module Specifications (10-bit

Mode), removing all parameters with the exception of HAD33b (see

Table 26-17).

TABLE B-2: MAJOR SECTION UPDATES (CONTINUED)

Section Name Update Description

dsPIC33FJXXXGPX06A/X08A/X10A

INDEX

A/D Converter ................................................................... 235

DMA .......................................................................... 235

Initialization ............................................................... 235

Key Features............................................................. 235

AC Characteristics .................................................... 278, 312

ADC Module.............................................................. 315

ADC Module (10-bit Mode) ....................................... 316

ADC Module (12-bit Mode) ....................................... 315

Internal RC Accuracy ................................................ 280

Load Conditions ................................................ 278, 312

ADC Module

ADC11 Register Map .................................................. 57

ADC2 Register Map .................................................... 57

Alternate Interrupt Vector Table (AIVT) .............................. 91

Arithmetic Logic Unit (ALU)................................................. 35

Assembler

MPASM Assembler................................................... 264

Barrel Shifter ....................................................................... 39

Bit-Reversed Addressing .................................................... 72

Example ...................................................................... 73

Implementation ........................................................... 72

Sequence Table (16-Entry)......................................... 73

Block Diagrams

16-bit Timer1 Module ................................................ 167

A/D Module ............................................................... 236

Connections for On-Chip Voltage Regulator............. 252

DCI Module ............................................................... 228

Device Clock ..................................................... 147, 149

DSP Engine ................................................................ 36

dsPIC33F .................................................................... 22

dsPIC33F CPU Core................................................... 30

ECAN Module ........................................................... 202

Input Capture ............................................................ 175

Output Compare ....................................................... 177

PLL............................................................................ 149

Reset System.............................................................. 85

Shared Port Structure ............................................... 165

SPI ............................................................................ 181

Timer2 (16-bit) .......................................................... 171

Timer2/3 (32-bit) ....................................................... 170

UART ........................................................................ 195

Watchdog Timer (WDT) ............................................ 253

C Compilers

MPLAB C18 .............................................................. 264

Clock Switching................................................................. 155

Enabling .................................................................... 155

Sequence.................................................................. 155

Code Examples

Erasing a Program Memory Page............................... 83

Initiating a Programming Sequence............................ 84

Loading Write Buffers ................................................. 84

Port Write/Read ........................................................ 166

PWRSAV Instruction Syntax..................................... 157

Code Protection ........................................................ 247, 254

Configuration Bits.............................................................. 247

Description (Table).................................................... 248

Configuration Register Map .............................................. 247

Configuring Analog Port Pins............................................ 166

CPU

Control Register.......................................................... 32

CPU Clocking System ...................................................... 148

Options ..................................................................... 148

Selection................................................................... 148

Customer Change Notification Service............................. 339

Customer Notification Service .......................................... 339

Customer Support............................................................. 339

Data Accumulators and Adder/Subtractor .......................... 37

Data Space Write Saturation ...................................... 39

Overflow and Saturation ............................................. 37

Round Logic ............................................................... 38

Write Back .................................................................. 38

Data Address Space........................................................... 43

Alignment.................................................................... 43

Memory Map for dsPIC33FJXXXGPX06A/X08A/X10A

Devices with 16 KB RAM.................................... 45

Memory Map for dsPIC33FJXXXGPX06A/X08A/X10A

Devices with 30 KB RAM.................................... 46

Memory Map for dsPIC33FJXXXGPX06A/X08A/X10A

Devices with 8 KB RAM...................................... 44

Near Data Space ........................................................ 43

Software Stack ........................................................... 69

Width .......................................................................... 43

Data Converter Interface (DCI) Module ............................ 227

DC Characteristics............................................................ 268

Doze Current (IDOZE)................................................ 311

High Temperature..................................................... 310

I/O Pin Input Specifications ...................................... 273

I/O Pin Output........................................................... 311

I/O Pin Output Specifications.................................... 276

Idle Current (IIDLE) .................................................... 271

Operating Current (IDD) ............................................ 270

Operating MIPS vs. Voltage ..................................... 310

Power-Down Current (IPD)........................................ 272

Power-down Current (IPD) ........................................ 310

Program Memory.............................................. 277, 311

Temperature and Voltage......................................... 310

Temperature and Voltage Specifications.................. 269

Thermal Operating Conditions.................................. 310

DCI

Buffer Control ........................................................... 227

Buffer Data Alignment .............................................. 227

Introduction............................................................... 227

Transmit/Receive Shift Register ............................... 227

DCI I/O Pins...................................................................... 227

COFS........................................................................ 227

CSCK........................................................................ 227

CSDI ......................................................................... 227

CSDO ....................................................................... 227

DCI Module

Development Support....................................................... 263

DMA Module

DMA Register Map ..................................................... 58

DMAC Registers............................................................... 138

DMAxCNT ................................................................ 138

DMAxCON................................................................ 138

DMAxPAD ................................................................ 138

DMAxREQ ................................................................ 138

DMAxSTA................................................................. 138

DMAxSTB................................................................. 138

dsPIC33FJXXXGPX06A/X08A/X10A

DSP Engine......................................................................... 35

Multiplier...................................................................... 37

ECAN Module

CiFMSKSEL2 register............................................... 219

ECAN1 Register Map (C1CTRL1.WIN = 0 or 1) ......... 60

ECAN1 Register Map (C1CTRL1.WIN = 0) ................ 60

ECAN1 Register Map (C1CTRL1.WIN = 1) ................ 61

ECAN2 Register Map (C2CTRL1.WIN = 0 or 1) ......... 63

ECAN2 Register Map (C2CTRL1.WIN = 0) .......... 63, 64

Frame Types............................................................. 201

Modes of Operation .................................................. 203

Overview ................................................................... 201

ECAN Registers

Filter 15-8 Mask Selection Register (CiFMSKSEL2). 219

Electrical Characteristics................................................... 267

AC ..................................................................... 278, 312

Enhanced CAN Module..................................................... 201

Equations

Device Operating Frequency .................................... 148

Errata .................................................................................. 19

Flash Program Memory....................................................... 79

Control Registers ........................................................ 80

Operations .................................................................. 80

Programming Algorithm .............................................. 83

RTSP Operation.......................................................... 80

Table Instructions........................................................ 79

Flexible Configuration ....................................................... 247

FSCM

Delay for Crystal and PLL Clock Sources ................... 89

Device Resets............................................................. 89

High Temperature Electrical Characteristics..................... 309

I/O Ports ............................................................................ 165

Parallel I/O (PIO)....................................................... 165

Write/Read Timing .................................................... 166

I2C

Operating Modes ...................................................... 187

Registers................................................................... 187

I2C Module

I2C1 Register Map ...................................................... 55

I2C2 Register Map ...................................................... 55

In-Circuit Debugger ........................................................... 254

In-Circuit Emulation........................................................... 247

In-Circuit Serial Programming (ICSP) ....................... 247, 254

Input Capture

Registers................................................................... 176

Input Change Notification Module ..................................... 166

Instruction Addressing Modes............................................. 69

File Register Instructions ............................................ 69

Fundamental Modes Supported.................................. 70

MAC Instructions......................................................... 70

MCU Instructions ........................................................ 69

Move and Accumulator Instructions............................ 70

Other Instructions........................................................ 70

Instruction Set

Overview ................................................................... 258

Summary................................................................... 255

Instruction-Based Power-Saving Modes........................... 157

Idle............................................................................ 158

Sleep ........................................................................ 157

Internal RC Oscillator

Use with WDT........................................................... 253

Internet Address ............................................................... 339

Interrupt Control and Status Registers ............................... 95

IECx............................................................................ 95

IFSx ............................................................................ 95

INTCON1.................................................................... 95

INTCON2.................................................................... 95

IPCx............................................................................ 95

Interrupt Setup Procedures............................................... 135

Initialization............................................................... 135

Interrupt Disable ....................................................... 135

Interrupt Service Routine.......................................... 135

Trap Service Routine ................................................ 135

Interrupt Vector Table (IVT) ................................................ 91

Interrupts Coincident with Power Save Instructions ......... 158

JTAG Boundary Scan Interface ........................................ 247

Memory Organization ......................................................... 41

Microchip Internet Web Site.............................................. 339

Modes of Operation

Disable...................................................................... 203

Initialization............................................................... 203

Listen All Messages.................................................. 203

Listen Only................................................................ 203

Loopback .................................................................. 203

Normal Operation ..................................................... 203

Modulo Addressing ............................................................. 70

Applicability................................................................. 72

Operation Example..................................................... 71

Start and End Address ............................................... 71

W Address Register Selection .................................... 71

MPLAB ASM30 Assembler, Linker, Librarian ................... 264

MPLAB Integrated Development Environment Software.. 263

MPLAB PM3 Device Programmer .................................... 266

MPLAB REAL ICE In-Circuit Emulator System ................ 265

MPLINK Object Linker/MPLIB Object Librarian ................ 264

NVM Module

Open-Drain Configuration................................................. 166

Output Compare ............................................................... 177

Packaging ......................................................................... 319

Details....................................................................... 323

Marking............................................................. 319, 320

Peripheral Module Disable (PMD) .................................... 158

Pinout I/O Descriptions (table)............................................ 23

PMD Module

POR and Long Oscillator Start-up Times ........................... 89

PORTA

PORTB

dsPIC33FJXXXGPX06A/X08A/X10A

PORTC

PORTD

PORTE

PORTF

PORTG

Power-Saving Features .................................................... 157

Clock Frequency and Switching................................ 157

Program Address Space..................................................... 41

Construction................................................................ 74

Data Access from Program Memory

Using Program Space Visibility........................... 77

Data Access from Program Memory

Using Table Instructions ..................................... 76

Data Access from, Address Generation...................... 75

Memory Map ............................................................... 41

Table Read Instructions

TBLRDH ............................................................. 76

TBLRDL .............................................................. 76

Visibility Operation ...................................................... 77

Program Memory

Interrupt Vector ........................................................... 42

Organization................................................................ 42

Reset Vector ............................................................... 42

Reader Response ............................................................. 340

Registers

ADxCHS0 (ADCx Input Channel 0 Select................. 244

ADxCHS123 (ADCx Input Channel 1, 2, 3 Select) ... 243

ADxCON1 (ADCx Control 1)..................................... 238

ADxCON2 (ADCx Control 2)..................................... 240

ADxCON3 (ADCx Control 3)..................................... 241

ADxCON4 (ADCx Control 4)..................................... 242

ADxCSSH (ADCx Input Scan Select High)............... 245

ADxCSSL (ADCx Input Scan Select Low) ................ 245

ADxPCFGH (ADCx Port Configuration High) ........... 246

ADxPCFGL (ADCx Port Configuration Low)............. 246

CiBUFPNT1 (ECAN Filter 0-3 Buffer Pointer)........... 214

CiBUFPNT2 (ECAN Filter 4-7 Buffer Pointer)........... 215

CiBUFPNT3 (ECAN Filter 8-11 Buffer Pointer)......... 215

CiBUFPNT4 (ECAN Filter 12-15 Buffer Pointer)....... 216

CiCFG1 (ECAN Baud Rate Configuration 1) ............ 212

CiCFG2 (ECAN Baud Rate Configuration 2) ............ 213

CiCTRL1 (ECAN Control 1) ...................................... 204

CiCTRL2 (ECAN Control 2) ...................................... 205

CiEC (ECAN Transmit/Receive Error Count)............ 211

CiFCTRL (ECAN FIFO Control)................................ 207

CiFEN1 (ECAN Acceptance Filter Enable) ............... 214

CiFIFO (ECAN FIFO Status)..................................... 208

CiFMSKSEL1 (ECAN Filter 7-0 Mask Selection)..... 218,

219

CiINTE (ECAN Interrupt Enable) .............................. 210

CiINTF (ECAN Interrupt Flag)................................... 209

CiRXFnEID (ECAN Acceptance Filter n

Extended Identifier)........................................... 217

CiRXFnSID (ECAN Acceptance Filter n

Standard Identifier) ........................................... 217

CiRXFUL1 (ECAN Receive Buffer Full 1) ................. 221

CiRXFUL2 (ECAN Receive Buffer Full 2) ................. 221

CiRXMnEID (ECAN Acceptance Filter Mask n Extended

Identifier)........................................................... 220

CiRXMnSID (ECAN Acceptance Filter Mask n Standard

Identifier) .......................................................... 220

CiRXOVF1 (ECAN Receive Buffer Overflow 1)........ 222

CiRXOVF2 (ECAN Receive Buffer Overflow 2)........ 222

CiTRBnDLC (ECAN Buffer n Data Length Control).. 225

CiTRBnDm (ECAN Buffer n Data Field Byte m) ....... 225

CiTRBnEID (ECAN Buffer n Extended Identifier) ..... 224

CiTRBnSID (ECAN Buffer n Standard Identifier)...... 224

CiTRBnSTAT (ECAN Receive Buffer n Status)........ 226

CiTRmnCON (ECAN TX/RX Buffer m Control) ........ 223

CiVEC (ECAN Interrupt Code) ................................. 206

CLKDIV (Clock Divisor) ............................................ 152

CORCON (Core Control)...................................... 34, 96

DCICON1 (DCI Control 1) ........................................ 229

DCICON2 (DCI Control 2) ........................................ 230

DCICON3 (DCI Control 3) ........................................ 231

DCISTAT (DCI Status) ............................................. 232

DMACS0 (DMA Controller Status 0) ........................ 143

DMACS1 (DMA Controller Status 1) ........................ 145

DMAxCNT (DMA Channel x Transfer Count) ........... 142

DMAxCON (DMA Channel x Control)....................... 139

DMAxPAD (DMA Channel x Peripheral Address) .... 142

DMAxREQ (DMA Channel x IRQ Select) ................. 140

DMAxSTA (DMA Channel x RAM Start Address A) . 141

DMAxSTB (DMA Channel x RAM Start Address B) . 141

DSADR (Most Recent DMA RAM Address) ............. 146

I2CxCON (I2Cx Control)........................................... 189

I2CxMSK (I2Cx Slave Mode Address Mask)............ 193

I2CxSTAT (I2Cx Status) ........................................... 191

ICxCON (Input Capture x Control)............................ 176

IEC0 (Interrupt Enable Control 0) ............................. 108

IEC1 (Interrupt Enable Control 1) ............................. 110

IEC2 (Interrupt Enable Control 2) ............................. 112

IEC3 (Interrupt Enable Control 3) ............................. 114

IEC4 (Interrupt Enable Control 4) ............................. 115

IFS0 (Interrupt Flag Status 0) ................................... 100

IFS1 (Interrupt Flag Status 1) ................................... 102

IFS2 (Interrupt Flag Status 2) ................................... 104

IFS3 (Interrupt Flag Status 3) ................................... 106

IFS4 (Interrupt Flag Status 4) ................................... 107

INTCON1 (Interrupt Control 1) ................................... 97

INTCON2 (Interrupt Control 2) ................................... 99

INTTREG Interrupt Control and Status Register ...... 134

IPC0 (Interrupt Priority Control 0) ............................. 116

IPC1 (Interrupt Priority Control 1) ............................. 117

IPC10 (Interrupt Priority Control 10) ......................... 126

IPC11 (Interrupt Priority Control 11) ......................... 127

IPC12 (Interrupt Priority Control 12) ......................... 128

IPC13 (Interrupt Priority Control 13) ......................... 129

IPC14 (Interrupt Priority Control 14) ......................... 130

IPC15 (Interrupt Priority Control 15) ......................... 131

IPC16 (Interrupt Priority Control 16) ......................... 132

IPC17 (Interrupt Priority Control 17) ......................... 133

IPC2 (Interrupt Priority Control 2) ............................. 118

IPC3 (Interrupt Priority Control 3) ............................. 119

IPC4 (Interrupt Priority Control 4) ............................. 120

IPC5 (Interrupt Priority Control 5) ............................. 121

IPC6 (Interrupt Priority Control 6) ............................. 122

IPC7 (Interrupt Priority Control 7) ............................. 123

IPC8 (Interrupt Priority Control 8) ............................. 124

IPC9 (Interrupt Priority Control 9) ............................. 125

NVMCOM (Flash Memory Control) ...................... 81, 82

OCxCON (Output Compare x Control) ..................... 179

OSCCON (Oscillator Control)................................... 150

OSCTUN (FRC Oscillator Tuning)............................ 154

dsPIC33FJXXXGPX06A/X08A/X10A

PLLFBD (PLL Feedback Divisor) .............................. 153

PMD1 (Peripheral Module Disable Control

PMD1 (Peripheral Module Disable Control Register 1)...

159

PMD2 (Peripheral Module Disable Control

PMD3 (Peripheral Module Disable Control

PMD3 (Peripheral Module Disable Control Register 3)...

163

RCON (Reset Control) ................................................ 86

RSCON (DCI Receive Slot Control).......................... 233

SPIxCON1 (SPIx Control 1) ...................................... 183

SPIxCON2 (SPIx Control 2) ...................................... 185

SPIxSTAT (SPIx Status and Control) ....................... 182

SR (CPU Status)......................................................... 96

T1CON (Timer1 Control)........................................... 168

TSCON (DCI Transmit Slot Control) ......................... 233

TxCON (T2CON, T4CON, T6CON or

T8CON Control) ................................................ 172

TyCON (T3CON, T5CON, T7CON or

T9CON Control) ................................................ 173

UxMODE (UARTx Mode).......................................... 196

UxSTA (UARTx Status and Control)......................... 198

Reset

Clock Source Selection............................................... 88

Special Function Register Reset States ..................... 89

Times .......................................................................... 88

Reset Sequence.................................................................. 91

Resets ................................................................................. 85

Serial Peripheral Interface (SPI) ....................................... 181

Software Simulator (MPLAB SIM)..................................... 265

Software Stack Pointer, Frame Pointer

CALLL Stack Frame.................................................... 69

Special Features of the CPU............................................. 247

SPI Module

SPI1 Register Map...................................................... 56

SPI2 Register Map...................................................... 56

Symbols Used in Opcode Descriptions............................. 256

System Control

Temperature and Voltage Specifications

AC ..................................................................... 278, 312

Timer1 ............................................................................... 167

Timer2/3, Timer4/5, Timer6/7 and Timer8/9 ..................... 169

Timing Characteristics

CLKO and I/O ........................................................... 281

Timing Diagrams

10-bit A/D Conversion (CHPS<1:0> = 01, SIMSAM = 0,

ASAM = 0,

SSRC<2:0> = 000) ........................................... 306

10-bit A/D Conversion (CHPS<1:0> = 01, SIMSAM = 0,

ASAM = 1, SSRC<2:0> = 111,

SAMC<4:0> = 00001) ....................................... 308

12-bit A/D Conversion (ASAM = 0, SSRC = 000) ..... 304

CAN I/O..................................................................... 300

DCI AC-Link Mode .................................................... 299

DCI Multi -Channel, I2S Modes ................................. 297

External Clock........................................................... 279

I2Cx Bus Data (Master Mode) .................................. 293

I2Cx Bus Data (Slave Mode) .................................... 295

I2Cx Bus Start/Stop Bits (Master Mode)................... 293

I2Cx Bus Start/Stop Bits (Slave Mode)..................... 295

Input Capture (CAPx) ............................................... 286

OC/PWM................................................................... 287

Output Compare (OCx)............................................. 286

Reset, Watchdog Timer, Oscillator Start-up Timer

and Power-up Timer ......................................... 282

SPIx Master Mode (CKE = 0) ................................... 288

SPIx Master Mode (CKE = 1) ................................... 289

SPIx Slave Mode (CKE = 0) ..................................... 290

SPIx Slave Mode (CKE = 1) ..................................... 291

Timer1, 2, 3, 4, 5, 6, 7, 8, 9 External Clock .............. 284

Timing Requirements

ADC Conversion (10-bit mode)................................. 317

ADC Conversion (12-bit Mode)................................. 317

CLKO and I/O ........................................................... 281

DCI AC-Link Mode............................................ 299, 301

DCI Multi-Channel, I2S Modes.......................... 298, 301

External Clock........................................................... 279

Input Capture ............................................................ 286

SPIx Master Mode (CKE = 0) ................................... 313

SPIx Module Master Mode (CKE = 1) ...................... 313

SPIx Module Slave Mode (CKE = 0) ........................ 314

SPIx Module Slave Mode (CKE = 1) ........................ 314

Timing Specifications

10-bit A/D Conversion Requirements ....................... 308

12-bit A/D Conversion Requirements ....................... 305

CAN I/O Requirements ............................................. 300

I2Cx Bus Data Requirements (Master Mode)........... 294

I2Cx Bus Data Requirements (Slave Mode)............. 296

Output Compare Requirements................................ 286

PLL Clock ......................................................... 280, 312

Reset, Watchdog Timer, Oscillator Start-up Timer,

Power-up Timer and Brown-out

Reset Requirements......................................... 283

Simple OC/PWM Mode Requirements ..................... 287

SPIx Master Mode (CKE = 0) Requirements............ 288

SPIx Master Mode (CKE = 1) Requirements............ 289

SPIx Slave Mode (CKE = 0) Requirements.............. 290

SPIx Slave Mode (CKE = 1) Requirements.............. 292

Timer1 External Clock Requirements ....................... 284

Timer2, Timer4, Timer6 and Timer8 External

Clock Requirements ......................................... 285

Timer3, Timer5, Timer7 and Timer9 External Clock

Requirements ................................................... 285

UART Module

UART1 Register Map.................................................. 56

UART2 Register Map.................................................. 56

Voltage Regulator (On-Chip) ............................................ 252

Watchdog Timer (WDT)............................................ 247, 253

Programming Considerations ................................... 253

WWW Address ................................................................. 339

WWW, On-Line Support ..................................................... 19

dsPIC33FJXXXGPX06A/X08A/X10A

THE MICROCHIP WEB SITE

Microchip provides online support via our WWW site at

www.microchip.com. This web site is used as a means

to make files and information easily available to

customers. Accessible by using your favorite Internet

browser, the web site contains the following

information:

•Product Support – Data sheets and errata,

application notes and sample programs, design

resources, user’s guides and hardware support

documents, latest software releases and archived

software

•General Technical Support – Frequently Asked

Questions (FAQ), technical support requests,

online discussion groups, Microchip consultant

program member listing

•Business of Microchip – Product selector and

ordering guides, latest Microchip press releases,

listing of seminars and events, listings of

Microchip sales offices, distributors and factory

representatives

CUSTOMER CHANGE NOTIFICATION

SERVICE

Microchip’s customer notification service helps keep

customers current on Microchip products. Subscribers

will receive e-mail notification whenever there are

changes, updates, revisions or errata related to a

specified product family or development tool of interest.

To register, access the Microchip web site at

www.microchip.com. Under “Support”, click on

“Customer Change Notification” and follow the

registration instructions.

CUSTOMER SUPPORT

Users of Microchip products can receive assistance

through several channels:

• Distributor or Representative

• Local Sales Office

• Field Application Engineer (FAE)

• Technical Support

• Development Systems Information Line

Customers should contact their distributor,

representative or field application engineer (FAE) for

support. Local sales offices are also available to help

customers. A listing of sales offices and locations is

included in the back of this document.

Technical support is available through the web site

at: http://microchip.com/support

dsPIC33FJXXXGPX06A/X08A/X10A

READER RESPONSE

It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip

product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our

documentation can better serve you, please FAX your comments to the Technical Publications Manager at

(480) 792-4150.

Please list the following information, and use this outline to provide us with your comments about this document.

TO: Technical Publications Manager

RE: Reader Response

Total Pages Sent ________

From: Name

Company

Address

City / State / ZIP / Country

Telephone: (_______) _________ - _________

Application (optional):

Would you like a reply? Y N

Device: Literature Number:

Questions:

FAX: (______) _________ - _________

DS70593CdsPIC33FJXXXGPX06A/X08A/X10A

1. What are the best features of this document?

2. How does this document meet your hardware and software development needs?

3. Do you find the organization of this document easy to follow? If not, why?

4. What additions to the document do you think would enhance the structure and subject?

5. What deletions from the document could be made without affecting the overall usefulness?

6. Is there any incorrect or misleading information (what and where)?

7. How would you improve this document?

dsPIC33FJXXXGPX06A/X08A/X10A

PRODUCT IDENTIFICATION SYSTEM

To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.

Architecture: 33 = 16-bit Digital Signal Controller

Flash Memory Family: FJ = Flash program memory, 3.3V

Product Group: GP2 = General purpose family

GP3 = General purpose family

GP5 = General purpose family

GP7 = General purpose family

Pin Count: 06 = 64-pin

08 = 80-pin

10 = 100-pin

Temperature Range: I = -40°C to+85°C(Industrial)

E=-40°C to+125°C(Extended)

H=-40°C to+150°C(High)

Package: PT = 10x10 or 12x12 mm TQFP (Thin Quad Flatpack)

PF = 14x14 mm TQFP (Thin Quad Flatpack)

MR = 9x9mm QFN (Plastic Quad Flatpack)

Pattern Three-digit QTP, SQTP, Code or Special Requirements

(blank otherwise)

ES = Engineering Sample

Examples:

a) dsPIC33FJ256GP710AI/PT:

General-purpose dsPIC33, 64 KB program

memory, 100-pin, Industrial temp.,

TQFP package.

Microchip Trademark

Architecture

Flash Memory Family

Program Memory Size (KB)

Product Group

Pin Count

Temperature Range

Package

Pattern

dsPIC 33 FJ 256 GP7 10 A T I / PT - XXX

Tape and Reel Flag (if applicable)

Revision Level

AMERICAS

Corporate Office

2355 West Chandler Blvd.

Chandler, AZ 85224-6199

Tel: 480-792-7200

Fax: 480-792-7277

Technical Support:

http://www.microchip.com/

support

Web Address:

www.microchip.com

Atlanta

Duluth, GA

Tel: 678-957-9614

Fax: 678-957-1455

Boston

Westborough, MA

Tel: 774-760-0087

Fax: 774-760-0088

Chicago

Itasca, IL

Tel: 630-285-0071

Fax: 630-285-0075

Cleveland

Independence, OH

Tel: 216-447-0464

Fax: 216-447-0643

Dallas

Addison, TX

Tel: 972-818-7423

Fax: 972-818-2924

Detroit

Farmington Hills, MI

Tel: 248-538-2250

Fax: 248-538-2260

Indianapolis

Noblesville, IN

Tel: 317-773-8323

Fax: 317-773-5453

Los Angeles

Mission Viejo, CA

Tel: 949-462-9523

Fax: 949-462-9608

Santa Clara

Santa Clara, CA

Tel: 408-961-6444

Fax: 408-961-6445

Toronto

Mississauga, Ontario,

Canada

Tel: 905-673-0699

Fax: 905-673-6509

ASIA/PACIFIC

Asia Pacific Office

Suites 3707-14, 37th Floor

Tower 6, The Gateway

Harbour City, Kowloon

Hong Kong

Tel: 852-2401-1200

Fax: 852-2401-3431

Australia - Sydney

Tel: 61-2-9868-6733

Fax: 61-2-9868-6755

China - Beijing

Tel: 86-10-8528-2100

Fax: 86-10-8528-2104

China - Chengdu

Tel: 86-28-8665-5511

Fax: 86-28-8665-7889

China - Chongqing

Tel: 86-23-8980-9588

Fax: 86-23-8980-9500

China - Hong Kong SAR

Tel: 852-2401-1200

Fax: 852-2401-3431

China - Nanjing

Tel: 86-25-8473-2460

Fax: 86-25-8473-2470

China - Qingdao

Tel: 86-532-8502-7355

Fax: 86-532-8502-7205

China - Shanghai

Tel: 86-21-5407-5533

Fax: 86-21-5407-5066

China - Shenyang

Tel: 86-24-2334-2829

Fax: 86-24-2334-2393

China - Shenzhen

Tel: 86-755-8203-2660

Fax: 86-755-8203-1760

China - Wuhan

Tel: 86-27-5980-5300

Fax: 86-27-5980-5118

China - Xian

Tel: 86-29-8833-7252

Fax: 86-29-8833-7256

China - Xiamen

Tel: 86-592-2388138

Fax: 86-592-2388130

China - Zhuhai

Tel: 86-756-3210040

Fax: 86-756-3210049

ASIA/PACIFIC

India - Bangalore

Tel: 91-80-3090-4444

Fax: 91-80-3090-4123

India - New Delhi

Tel: 91-11-4160-8631

Fax: 91-11-4160-8632

India - Pune

Tel: 91-20-2566-1512

Fax: 91-20-2566-1513

Japan - Yokohama

Tel: 81-45-471- 6166

Fax: 81-45-471-6122

Korea - Daegu

Tel: 82-53-744-4301

Fax: 82-53-744-4302

Korea - Seoul

Tel: 82-2-554-7200

Fax: 82-2-558-5932 or

82-2-558-5934

Malaysia - Kuala Lumpur

Tel: 60-3-6201-9857

Fax: 60-3-6201-9859

Malaysia - Penang

Tel: 60-4-227-8870

Fax: 60-4-227-4068

Philippines - Manila

Tel: 63-2-634-9065

Fax: 63-2-634-9069

Singapore

Tel: 65-6334-8870

Fax: 65-6334-8850

Taiwan - Hsin Chu

Tel: 886-3-6578-300

Fax: 886-3-6578-370

Taiwan - Kaohsiung

Tel: 886-7-213-7830

Fax: 886-7-330-9305

Taiwan - Taipei

Tel: 886-2-2500-6610

Fax: 886-2-2508-0102

Thailand - Bangkok

Tel: 66-2-694-1351

Fax: 66-2-694-1350

EUROPE

Austria - Wels

Tel: 43-7242-2244-39

Fax: 43-7242-2244-393

Denmark - Copenhagen

Tel: 45-4450-2828

Fax: 45-4485-2829

France - Paris

Tel: 33-1-69-53-63-20

Fax: 33-1-69-30-90-79

Germany - Munich

Tel: 49-89-627-144-0

Fax: 49-89-627-144-44

Italy - Milan

Tel: 39-0331-742611

Fax: 39-0331-466781

Netherlands - Drunen

Tel: 31-416-690399

Fax: 31-416-690340

Spain - Madrid

Tel: 34-91-708-08-90

Fax: 34-91-708-08-91

UK - Wokingham

Tel: 44-118-921-5869

Fax: 44-118-921-5820

Worldwide Sales and Service

02/18/11