LM2717-ADJ LM2717-ADJ Dual Step-Down DC/DC Converter Literature Number: SNVS407B LM2717-ADJ Dual Step-Down DC/DC Converter General Description Features The LM2717-ADJ is composed of two PWM DC/DC buck (step-down) converters. Both converters are used to generate an adjustable output voltage as low as 1.267V. Both also feature low RDSON (0.16) internal switches for maximum efficiency. Operating frequency can be adjusted anywhere between 300kHz and 600kHz allowing the use of small external components. External soft-start pins for each converter enables the user to tailor the soft-start times to a specific application. Each converter may also be shut down independently with its own shutdown pin. The LM2717-ADJ is available in a low profile 24-lead TSSOP package ensuring a low profile overall solution. Adjustable buck converter with a 2.2A, 0.16, internal switch (Buck 1) Adjustable buck converter with a 3.2A, 0.16, internal switch (Buck 2) Operating input voltage range of 4V to 20V Input undervoltage protection 300kHz to 600kHz pin adjustable operating frequency Over temperature protection Small 24-Lead TSSOP package Applications TFT-LCD Displays Handheld Devices Portable Applications Laptop Computers Automotive Applications Typical Application Circuit 20167901 (c) 2008 National Semiconductor Corporation 201679 www.national.com LM2717-ADJ Dual Step-Down DC/DC Converter March 4, 2008 LM2717-ADJ Connection Diagram Top View 20167904 24-Lead TSSOP Ordering Information Order Number Spec LM2717MT-ADJ LM2717MTX-ADJ Package Type NSC Package Drawing TSSOP-24 MTC24 61 Units, Rail Supplied As TSSOP-24 MTC24 2500 Units, Tape and Reel LM2717MT-ADJ NOPB TSSOP-24 MTC24 61 Units, Rail LM2717MTX-ADJ NOPB TSSOP-24 MTC24 2500 Units, Tape and Reel www.national.com 2 Pin Name 1 PGND Power ground. PGND and AGND pins must be connected together directly at the part. Function 2 PGND Power ground. PGND and AGND pins must be connected together directly at the part. 3 AGND Analog ground. PGND and AGND pins must be connected together directly at the part. 4 FB1 Buck 1 output voltage feedback input. 5 VC1 Buck 1 compensation network connection. Connected to the output of the voltage error amplifier. 6 VBG Bandgap connection. 7 VC2 Buck 2 compensation network connection. Connected to the output of the voltage error amplifier. 8 FB2 Buck 2 output voltage feedback input. 9 AGND Analog ground. PGND and AGND pins must be connected together directly at the part. 10 AGND Analog ground. PGND and AGND pins must be connected together directly at the part. 11 PGND Power ground. PGND and AGND pins must be connected together directly at the part. 12 PGND Power ground. PGND and AGND pins must be connected together directly at the part. 13 SW2 14 VIN Analog power input. All VIN pins are internally connected and should be connected together directly at the part. 15 VIN Analog power input. All VIN pins are internally connected and should be connected together directly at the part. 16 CB2 Buck 2 converter bootstrap capacitor connection. 17 SHDN2 18 SS2 19 FSLCT Buck 2 power switch input. Switch connected between VIN pins and SW2 pin. Shutdown pin for Buck 2 converter. Active low. Buck 2 soft start pin. Switching frequency select input. Use a resistor to set the frequency anywhere between 300kHz and 600kHz. 20 SS1 21 SHDN1 Buck 1 soft start pin. 22 CB1 Buck 1 converter bootstrap capacitor connection. 23 VIN Analog power input. All VIN pins are internally connected and should be connected together directly at the part. 24 SW1 Shutdown pin for Buck 1 converter. Active low. Buck 1 power switch input. Switch connected between VIN pins and SW1 pin. 3 www.national.com LM2717-ADJ Pin Descriptions LM2717-ADJ Block Diagram 20167903 www.national.com 4 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. VIN SW1 Voltage SW2 Voltage FB1, FB2 Voltages CB1, CB2 Voltages -0.3V to 22V -0.3V to 22V -0.3V to 22V -0.3V to 7V -0.3V to VIN+7V (VIN=VSW) Operating Junction Temperature Range (Note 4) Storage Temperature Supply Voltage SW1 Voltage SW2 Voltage Switching Frequency 0.965V VC2 1.565V -0.3V to 7.5V -0.3V to 7.5V -0.3V to 2.1V -0.3V to 2.1V AGND to 5V VC2 Voltage SHDN1 Voltage SHDN2 Voltage SS1 Voltage SS2 Voltage FSLCT Voltage 2kV Operating Conditions 1.75V VC1 2.25V VC1 Voltage 150C Internally Limited 300C 215C 220C -40C to +125C -65C to +150C 4V to 20V 20V 20V 300kHz to 600kHz Electrical Characteristics Specifications in standard type face are for TJ = 25C and those with boldface type apply over the full Operating Temperature Range (TJ = -40C to +125C). VIN = 5V, IL = 0A, and FSW = 300kHz unless otherwise specified. Symbol IQ Parameter Conditions Min (Note 4) Total Quiescent Current (both Not Switching switchers) Switching, switch open VSHDN = 0V 1.248 1.230 Typ (Note 5) Max (Note 4) Units 2.7 6 mA 6 12 mA 9 27 A 1.267 1.294 1.299 V 0.01 0.125 %/V VBG Bandgap Voltage %VBG/VIN Bandgap Voltage Line Regulation VFB1 Buck 1 Feedback Voltage 1.236 1.214 1.258 1.286 1.288 V VFB2 Buck 2 Feedback Voltage 1.236 1.214 1.258 1.286 1.288 V ICL1(Note 6) Buck 1 Switch Current Limit -0.01 VIN = 8V (Note 7) 2.2 VIN = 12V, VOUT = 3.3V ICL2(Note 6) Buck 2 Switch Current Limit 1.4 VIN = 8V (Note 7) 1.65 2.0 3.2 VIN = 12V, VOUT = 5V 2.6 3.05 3.5 A A IB1 Buck 1 FB Pin Bias Current (Note 8) VIN = 20V 70 400 nA IB2 Buck 2 FB Pin Bias Current (Note 8) VIN = 20V 65 400 nA VIN Input Voltage Range 20 V gm1 Buck 1 Error Amp Transconductance I = 20A 1340 mho gm2 Buck 2 Error Amp Transconductance I = 20A 1360 mho AV1 Buck 1 Error Amp Voltage Gain 134 V/V AV2 Buck 2 Error Amp Voltage Gain 136 V/V DMAX Maximum Duty Cycle FSW Switching Frequency 4 89 93 RF = 46.4k 240 300 360 kHz RF = 22.6k 480 600 720 kHz 5 % www.national.com LM2717-ADJ Maximum Junction Temperature Power Dissipation(Note 2) Lead Temperature Vapor Phase (60 sec.) Infrared (15 sec.) ESD Susceptibility (Note 3) Human Body Model Absolute Maximum Ratings (Note 1) LM2717-ADJ Symbol Parameter Conditions Min (Note 4) Typ (Note 5) Max (Note 4) Units ISHDN1 Buck 1 Shutdown Pin Current 0V < VSHDN1 < 7.5V -5 5 A ISHDN2 Buck 2 Shutdown Pin Current 0V < VSHDN2 < 7.5V -5 5 A IL1 Buck 1 Switch Leakage Current VIN = 20V 0.01 5 A IL2 Buck 2 Switch Leakage Current VIN = 20V 0.01 5 A RDSON1 Buck 1 Switch RDSON (Note 9) ISW = 100mA 160 180 300 m RDSON2 Buck 2 Switch RDSON (Note 9) ISW = 100mA 160 180 300 m ThSHDN1 Buck 1 SHDN Threshold Output High 1.8 Output Low ThSHDN2 Buck 2 SHDN Threshold 1.36 1.33 Output High 1.8 Output Low 0.7 1.36 1.33 0.7 V V ISS1 Buck 1 Soft Start Pin Current 4 9 15 A ISS2 Buck 2 Soft Start Pin Current 4 9 15 A UVP On Threshold 4 3.8 Off Threshold JA Thermal Resistance (Note 10) 3.6 TSSOP, package only 3.3 115 V C/W Note 1: Absolute maximum ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions for which the device is intended to be functional, but device parameter specifications may not be guaranteed. For guaranteed specifications and test conditions, see the Electrical Characteristics. Note 2: The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal resistance, JA, and the ambient temperature, TA. See the Electrical Characteristics table for the thermal resistance. The maximum allowable power dissipation at any ambient temperature is calculated using: PD (MAX) = (TJ(MAX) - TA)/JA. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Note 3: The human body model is a 100 pF capacitor discharged through a 1.5k resistor into each pin. Note 4: All limits guaranteed at room temperature (standard typeface) and at temperature extremes (bold typeface). All room temperature limits are 100% tested or guaranteed through statistical analysis. All limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL). Note 5: Typical numbers are at 25C and represent the most likely norm. Note 6: Duty cycle affects current limit due to ramp generator. Note 7: Current limit at 0% duty cycle. See TYPICAL PERFORMANCE section for Switch Current Limit vs. Input Voltage. Note 8: Bias current flows into FB pin. Note 9: Includes the bond wires and package leads, RDSON from VIN pin(s) to SW pin. Note 10: Refer to National's packaging website for more detailed thermal information and mounting techniques for the TSSOP package. www.national.com 6 LM2717-ADJ Typical Performance Characteristics Shutdown IQ vs. Input Voltage Switching IQ vs. Input Voltage (FSW = 300kHz) 20167960 20167961 Switching Frequency vs. Input Voltage (FSW = 300kHz) Buck 1 RDS(ON) vs. Input Voltage 20167963 20167962 Buck 2 RDS(ON) vs. Input Voltage Buck 1 Efficiency vs. Load Current (VOUT = 3.3V) 20167964 20167965 7 www.national.com LM2717-ADJ Buck 2 Efficiency vs. Load Current (VOUT = 15V) Buck 2 Efficiency vs. Load Current (VOUT = 5V) 20167966 20167967 Buck 1 Switch Current Limit vs. Input Voltage Buck 2 Switch Current Limit vs. Input Voltage 20167969 20167968 Buck 1 Switch Current Limit vs. Temperature (VIN = 12V) Buck 2 Switch Current Limit vs. Temperature (VIN = 12V) 20167912 www.national.com 20167913 8 Buck 2 Switch ON Resistance vs. Temperature 20167910 20167911 Switching Frequency vs. RF Resistance 20167914 and the load current is supplied by COUT and the rising current through the inductor. During the second cycle the transistor is open and the diode is forward biased due to the fact that the inductor current cannot instantaneously change direction. The energy stored in the inductor is transferred to the load and output capacitor. The ratio of these two cycles determines the output voltage. The output voltage is defined approximately as: Buck Operation PROTECTION (BOTH REGULATORS) The LM2717-ADJ has dedicated protection circuitry running during normal operation to protect the IC. The Thermal Shutdown circuitry turns off the power devices when the die temperature reaches excessive levels. The UVP comparator protects the power devices during supply power startup and shutdown to prevent operation at voltages less than the minimum input voltage. The OVP comparator is used to prevent the output voltage from rising at no loads allowing full PWM operation over all load conditions. The LM2717-ADJ also features a shutdown mode for each converter decreasing the supply current to approximately 10A (both in shutdown mode). where D is the duty cycle of the switch, D and D will be required for design calculations. The LM2717-ADJ has a minimum switch ON time which corresponds to a minimum duty cycle of approximately 10% at 600kHz operation and approximately 5% at 300kHz operation. In the case of some high voltage differential applications (low duty cycle operation) this minimum duty cycle may be exceeded causing the feedback pin over-voltage protection to trip as the output voltage rises. This will put the device into a PFM type operation which can cause an unpredictable frequency spectrum and may cause the average output voltage to rise slightly. If this is a concern the switching frequency may CONTINUOUS CONDUCTION MODE The LM2717-ADJ contains current-mode, PWM buck regulators. A buck regulator steps the input voltage down to a lower output voltage. In continuous conduction mode (when the inductor current never reaches zero at steady state), the buck regulator operates in two cycles. The power switch is connected between VIN and SW1 and SW2. In the first cycle of operation the transistor is closed and the diode is reverse biased. Energy is collected in the inductor 9 www.national.com LM2717-ADJ Buck 1 Switch ON Resistance vs. Temperature LM2717-ADJ be lowered and/or a pre-load added to the output to keep the device full PWM operation. Note that the OVP function monitors the FB pin so it will not function if the feedback resistor is disconnected from the output. Due to slight differences between the two converters it is recommended that Buck 1 be used for the lower of the two output voltages for best operation. this minimum requirement at the peak inductor current expected for the application regardless of what the inductor ripple current and output ripple voltage requirements are. A value larger than 2LMIN is acceptable if the ripple requirements of the application require it but it may reduce the phase margin and increase the difficulty in compensating the circuit. The most important parameters for the inductor from an applications standpoint are the inductance, peak current and the DC resistance. The inductance is related to the peak-to-peak inductor ripple current, the input and the output voltages (for 300kHz operation): DESIGN PROCEDURE This section presents guidelines for selecting external components. SETTING THE OUTPUT VOLTAGE The output voltage is set using the feedback pin and a resistor divider connected to the output as shown in Figure 4. The feedback pin voltage (VFB) is 1.258V, so the ratio of the feedback resistors sets the output voltage according to the following equation: A higher value of ripple current reduces inductance, but increases the conductance loss, core loss, and current stress for the inductor and switch devices. It also requires a bigger output capacitor for the same output voltage ripple requirement. A reasonable value is setting the ripple current to be 30% of the DC output current. Since the ripple current increases with the input voltage, the maximum input voltage is always used to determine the inductance. The DC resistance of the inductor is a key parameter for the efficiency. Lower DC resistance is available with a bigger winding area. A good tradeoff between the efficiency and the core size is letting the inductor copper loss equal 2% of the output power. INPUT CAPACITOR A low ESR aluminum, tantalum, or ceramic capacitor is needed between the input pin and power ground. This capacitor prevents large voltage transients from appearing at the input. The capacitor is selected based on the RMS current and voltage requirements. The RMS current is given by: OUTPUT CAPACITOR The selection of COUT is driven by the maximum allowable output voltage ripple. The output ripple in the constant frequency, PWM mode is approximated by: The RMS current reaches its maximum (IOUT/2) when VIN equals 2VOUT. This value should be calculated for both regulators and added to give a total RMS current rating. For an aluminum or ceramic capacitor, the voltage rating should be at least 25% higher than the maximum input voltage. If a tantalum capacitor is used, the voltage rating required is about twice the maximum input voltage. The tantalum capacitor should be surge current tested by the manufacturer to prevent being shorted by the inrush current. The minimum capacitor value should be 47F for lower output load current applications and less dynamic (quickly changing) load conditions. For higher output current applications or dynamic load conditions a 68F to 100F low ESR capacitor is recommended. It is also recommended to put a small ceramic capacitor (0.1F to 4.7F) between the input pins and ground to reduce high frequency spikes. The ESR term usually plays the dominant role in determining the voltage ripple. Low ESR ceramic, aluminum electrolytic, or tantalum capacitors (such as MuRata MLCC, Taiyo Yuden MLCC, Nichicon PL series, Sanyo OS-CON, Sprague 593D, 594D, AVX TPS, and CDE polymer aluminum) is recommended. An aluminum electrolytic capacitor is not recommended for temperatures below -25C since its ESR rises dramatically at cold temperatures. Ceramic or tantalum capacitors have much better ESR specifications at cold temperature and is preferred for low temperature applications. BOOTSTRAP CAPACITOR A 4.7nF ceramic capacitor or larger is recommended for the bootstrap capacitor. For applications where the input voltage is less than twice the output voltage a larger capacitor is recommended, generally 0.1F to 1F to ensure plenty of gate drive for the internal switches and a consistently low RDSON. INDUCTOR SELECTION The most critical parameter for the inductor in a current mode switcher is the minimum value required for stable operation. To prevent subharmonic oscillations and achieve good phase margin a target minimum value for the inductor is: SOFT-START CAPACITOR (BOTH REGULATORS) The LM2717-ADJ contains circuitry that can be used to limit the inrush current on start-up of the DC/DC switching regulators. This inrush current limiting circuitry serves as a soft-start. The external SS pins are used to tailor the soft-start for a specific application. A current (ISS) charges the external softstart capacitor, CSS. The soft-start time can be estimated as: Where VIN is the minimum input voltage and RDSON is the maximum switch ON resistance. For best stability the inductor should be in the range of 0.5LMIN (absolute minimum) and 2LMIN. Using an inductor with a value less than 0.5LMIN can cause subharmonic oscillations. The inductor should meet www.national.com TSS = CSS*0.6V/ISS When programming the soft-start time use the equation given in the Soft-Start Capacitor section above. The soft-start function is used simply to limit inrush current to the device that 10 LM2717-ADJ could stress the input voltage supply. The soft-start time described above is the time it takes for the current limit to ramp to maximum value. When this function is used the current limit starts at a low value and increases to nominal at the set softstart time. Under maximum load conditions the output voltage may rise at the same rate as the soft-start, however at light or no load conditions the output voltage will rise much faster as the switch will not need to conduct much current to charge the output capacitor. SHUTDOWN OPERATION (BOTH REGULATORS) The shutdown pins of the LM2717-ADJ are designed so that they may be controlled using 1.8V or higher logic signals. If the shutdown function is not to be used the pin may be left open. The maximum voltage to the shutdown pin should not exceed 7.5V. If the use of a higher voltage is desired due to system or other constraints it may be used, however a 100k or larger resistor is recommended between the applied voltage and the shutdown pin to protect the device. 20167916 FIGURE 1. Control-Output Transfer Function As shown in Figure 1, the example control-output transfer function consists of one pole (fp), one zero (fz), and a double pole at fn (half the switching frequency). The following can be done to create a -20dB /decade roll-off of the loop gain: Place the first pole at 0Hz, the first zero at fp, the second pole at fz, and the second zero at fn. The resulting output-control transfer function is shown in Figure 2. SCHOTTKY DIODE The breakdown voltage rating of D1 and D2 is preferred to be 25% higher than the maximum input voltage. The current rating for the diode should be equal to the maximum output current for best reliability in most applications. In cases where the input voltage is much greater than the output voltage the average diode current is lower. In this case it is possible to use a diode with a lower average current rating, approximately (1-D)*IOUT however the peak current rating should be higher than the maximum load current. LOOP COMPENSATION The general purpose of loop compensation is to meet static and dynamic performance requirements while maintaining stability. Loop gain is what is usually checked to determine small-signal performance. Loop gain is equal to the product of control-output transfer function and the output-control transfer function (the compensation network transfer function). The DC loop gain of the LM2717 is usually around 55dB to 60dB when loaded. Generally speaking it is a good idea to have a loop gain slope that is -20dB /decade from a very low frequency to well beyond the crossover frequency. The crossover frequency should not exceed one-fifth of the switching frequency, i.e. 60kHz in the case of 300kHz switching frequency. The higher the bandwidth is, the faster the load transient response speed will potentially be. However, if the duty cycle saturates during a load transient, further increasing the small signal bandwidth will not help. Since the controloutput transfer function usually has very limited low frequency gain, it is a good idea to place a pole in the compensation at zero frequency, so that the low frequency gain will be relatively large. A large DC gain means high DC regulation accuracy (i.e. DC voltage changes little with load or line variations). The rest of the compensation scheme depends highly on the shape of the control-output plot. 20167917 FIGURE 2. Output-Control Transfer Function The control-output corner frequencies, and thus the desired compensation corner frequencies, can be determined approximately by the following equations: Where Co is the output capacitance, Re is the output capacitance ESR, Ro is the load resistance, L is the inductor value, and f is the switching frequency used. Since fp is determined by the output network, it will shift with loading (Ro) and duty cycle. First determine the range of frequencies (fpmin/max) of the pole across the expected load range, then place the first compensation zero within that range. Example: Vo = 5V, Re = 20m, Co = 100F, Romax = 5V/100mA = 50, Romin = 5V/1A = 5, L = 10H, f = 300kHz: 11 www.national.com LM2717-ADJ A second zero can also be added with a resistor in series with Cc2. If used, this zero should be placed at fn, where the control to output gain rolls off at -40dB/dec. Generally, fn will be well below the 0dB level and thus will have little effect on stability. Rc2 can be calculated with the following equation: Once the fp range is determined, Rc1 should be calculated using: 20167930 Where B is the desired gain in V/V at fp (fz1), gm is the transconductance of the error amplifier, and R1 and R2 are the feedback resistors as shown in Figure 3. A gain value around 10dB (3.3v/v) is generally a good starting point. Example: B = 3.3 v/v, gm=1350mho, R1 = 20 K, R2 = 59 K: FIGURE 3. Compensation Network Note that the values calculated here give a good baseline for stability and will work well with most applications. The values in some cases may need to be adjusted some for optimum stability or the values may need to be adjusted depending on a particular applications bandwidth requirements. LAYOUT CONSIDERATIONS The LM2717-ADJ uses two separate ground connections, PGND for the drivers and boost NMOS power device and AGND for the sensitive analog control circuitry. The AGND and PGND pins should be tied directly together at the package. The feedback and compensation networks should be connected directly to a dedicated analog ground plane and this ground plane must connect to the AGND pin. If no analog ground plane is available then the ground connections of the feedback and compensation networks must tie directly to the AGND pin. Connecting these networks to the PGND can inject noise into the system and effect performance. The input bypass capacitor CIN, as shown in Figure 4, must be placed close to the IC. This will reduce copper trace resistance which effects input voltage ripple of the IC. For additional input voltage filtering, a 0.1F to 4.7F bypass capacitors can be placed in parallel with CIN, close to the VIN pins to shunt any high frequency noise to ground. The output capacitors, COUT1 and COUT2, should also be placed close to the IC. Any copper trace connections for the COUTX capacitors can increase the series resistance, which directly effects output voltage ripple. The feedback network, resistors RFB1(3) and RFB2(4), should be kept close to the FB pin, and away from the inductor to minimize copper trace connections that can inject noise into the system. Trace connections made to the inductors and schottky diodes should be minimized to reduce power dissipation and increase overall efficiency. For more detail on switching power supply layout considerations see Application Note AN-1149: Layout Guidelines for Switching Power Supplies. Bandwidth will vary proportional to the value of Rc1. Next, Cc1 can be determined with the following equation: Example: fpmin = 297 Hz, Rc1 = 20 K: The value of Cc1 should be within the range determined by fpmin/max. A higher value will generally provide a more stable loop, but too high a value will slow the transient response time. The compensation network (Figure 3) will also introduce a low frequency pole which will be close to 0Hz. A second pole should also be placed at fz. This pole can be created with a single capacitor Cc2 and a shorted Rc2 (see Figure 3). The minimum value for this capacitor can be calculated by: Cc2 may not be necessary, however it does create a more stable control loop. This is especially important with high load currents. Example: fz = 80 kHz, Rc1 = 20 K: www.national.com 12 Some Recommended Inductors (Others May Be Used) Manufacturer Inductor Contact Information Coilcraft DO3316 and DT3316 series www.coilcraft.com 800-3222645 TDK SLF10145 series www.component.tdk.com 847-803-6100 Pulse P0751 and P0762 series www.pulseeng.com Sumida CDRH8D28 and CDRH8D43 series www.sumida.com Some Recommended Input And Output Capacitors (Others May Be Used) Manufacturer Capacitor Contact Information Vishay Sprague 293D, 592D, and 595D series tantalum www.vishay.com Taiyo Yuden High capacitance MLCC ceramic www.t-yuden.com Cornell Dubilier ESRD seriec Polymer Aluminum Electrolytic SPV and AFK series V-chip series www.cde.com MuRata High capacitance MLCC ceramic www.murata.com 20167958 FIGURE 4. 15V, 3.3V Output Application 13 www.national.com LM2717-ADJ Application Information LM2717-ADJ 20167959 FIGURE 5. 5V, 3.3V Output Application 20167915 FIGURE 6. 3.3V, 1.8V Output Application www.national.com 14 LM2717-ADJ Physical Dimensions inches (millimeters) unless otherwise noted TSSOP-24 Pin Package (MTC) For Ordering, Refer to Ordering Information Table NS Package Number MTC24 15 www.national.com LM2717-ADJ Dual Step-Down DC/DC Converter Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated