GLS29SF020-55-4I-WHE - Greenliant

Data Sheet

www.greenliant.com

2 Mbit / 4 Mbit (x8) Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

FEATURES:

• Organized as 256K x8 / 512K x8

• Single Voltage Read and Write Operations

– 4.5-5.5V for GLS29SF020/040

– 2.7-3.6V for GLS29VF020/040

• Superior Reliability

– Endurance: 100,000 Cycles (typical)

– Greater than 100 years Data Retention

• Low Power Consumption:

– Active Current: 10 mA (typical)

– Standby Current:

30 µA (typical) for GLS29SF020/040

1 µA (typical) for GLS29VF020/040

• Sector-Erase Capability

– Uniform 128 Byte sectors

• Fast Read Access Time:

– 55 ns for GLS29SF020/040

– 70 ns for GLS29VF020/040

• Latched Address and Data

• Fast Erase and Byte-Program:

– Sector-Erase Time: 18 ms (typical)

– Chip-Erase Time: 70 ms (typical)

– Byte-Program Time: 14 µs (typical)

– Chip Rewrite Time:

4 seconds (typical) for GLS29SF/VF020

8 seconds (typical) for GLS29SF/VF040

• Automatic Write Timing

– Internal VPP Generation

• End-of-Write Detection

– Toggle Bit

– Data# Polling

• TTL I/O Compatibility for GLS29SF020/040

• CMOS I/O Compatibility for GLS29VF020/040

• JEDEC Standard

– Flash EEPROM Pinouts and command sets

• Packages Available

– 32-lead PLCC

– 32-lead TSOP (8mm x 14mm)

• All non-Pb (lead-free) devices are RoHS compliant

PRODUCT DESCRIPTION

The GLS29SF020/040 and GLS29VF020/040 are 256K

x8 / 512K x8 CMOS Small-Sector Flash (SSF) manufac-

tured with high-performance SuperFlash technology. The

split-gate cell design and thick-oxide tunneling injector

attain better reliability and manufacturability compared with

alternate approaches. The GLS29SF020/040 devices

write (Program or Erase) with a 4.5-5.5V power supply.

The GLS29VF020/040 devices write (Program or Erase)

with a 2.7-3.6V power supply. These devices conform to

JEDEC standard pin assignments for x8 memories.

Featuring high performance Byte-Program, the

GLS29SF020/040 and GLS29VF020/040 devices pro-

vide a maximum Byte-Program time of 20 µsec. To protect

against inadvertent write, they have on-chip hardware and

Software Data Protection schemes. Designed, manufac-

tured, and tested for a wide spectrum of applications, these

devices are offered with a guaranteed endurance of at

least 10,000 cycles. Data retention is rated at greater than

100 years.

The GLS29SF020/040 and GLS29VF020/040 devices

are suited for applications that require convenient and eco-

nomical updating of program, configuration, or data mem-

ory. For all system applications, they significantly improve

performance and reliability, while lowering power consump-

tion. They inherently use less energy during Erase and

Program than alternative flash technologies. The total

energy consumed is a function of the applied voltage, cur-

rent, and time of application. Since for any given voltage

range, the SuperFlash technology uses less current to pro-

gram and has a shorter erase time, the total energy con-

sumed during any Erase or Program operation is less than

alternative flash technologies. They also improve flexibility

while lowering the cost for program, data, and configuration

storage applications.

The SuperFlash technology provides fixed Erase and Pro-

gram times independent of the number of Erase/Program

cycles that have occurred. Therefore, the system software

or hardware does not have to be modified or de-rated as is

necessary with alternative flash technologies, whose Erase

and Program times increase with accumulated Erase/Pro-

gram cycles.

GLS29SF/VF020 / 0402Mb / 4Mb (x8)

Byte-Program, Small-Sector flash memories

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

To meet high density, surface mount requirements, the

GLS29SF020/040 and GLS29VF020/040 devices are

offered in 32-lead PLCC and 32-lead TSOP packages. The

pin assignments are shown in Figures 2 and 3.

Device Operation

Commands are used to initiate the memory operation func-

tions of the device. Commands are written to the device

using standard microprocessor write sequences. A com-

mand is written by asserting WE# low while keeping CE#

low. The address bus is latched on the falling edge of WE#

or CE#, whichever occurs last. The data bus is latched on

the rising edge of WE# or CE#, whichever occurs first.

Read

The Read operation of the GLS29SF020/040 and

GLS29VF020/040 devices are controlled by CE# and

OE#, both have to be low for the system to obtain data

from the outputs. CE# is used for device selection. When

CE# is high, the chip is deselected and only standby power

is consumed. OE# is the output control and is used to gate

data from the output pins. The data bus is in high imped-

ance state when either CE# or OE# is high. Refer to the

Read cycle timing diagram in Figure 4 for further details.

Byte-Program Operation

The GLS29SF020/040 and GLS29VF020/040 devices

are programmed on a byte-by-byte basis. Before program-

ming, the sector where the byte exists must be fully erased.

The Program operation is accomplished in three steps.

The first step is the three-byte load sequence for Software

Data Protection. The second step is to load byte address

and byte data. During the Byte-Program operation, the

addresses are latched on the falling edge of either CE# or

WE#, whichever occurs last. The data is latched on the ris-

ing edge of either CE# or WE#, whichever occurs first. The

third step is the internal Program operation which is initi-

ated after the rising edge of the fourth WE# or CE#, which-

ever occurs first. The Program operation, once initiated, will

be completed, within 20 µs. See Figures 5 and 6 for WE#

and CE# controlled Program operation timing diagrams

and Figure 16 for flowcharts. During the Program opera-

tion, the only valid reads are Data# Polling and Toggle Bit.

During the internal Program operation, the host is free to

perform additional tasks. Any commands written during the

internal Program operation will be ignored.

Sector-Erase Operation

The Sector-Erase operation allows the system to erase the

device on a sector-by-sector basis. The GLS29SF020/

040 and GLS29VF020/040 offer Sector-Erase mode. The

sector architecture is based on uniform sector size of 128

Bytes. The Sector-Erase operation is initiated by executing

a six-byte command sequence with Sector-Erase com-

mand (20H) and sector address (SA) in the last bus cycle.

The sector address is latched on the falling edge of the

sixth WE# pulse, while the command (20H) is latched on

the rising edge of the sixth WE# pulse. The internal Erase

operation begins after the sixth WE# pulse. The End-of-

Erase operation can be determined using either Data#

Polling or Toggle Bit methods. For timing waveforms, see

Figure 9. Any commands issued during the Sector-Erase

operation are ignored.

Chip-Erase Operation

The GLS29SF020/040 and GLS29VF020/040 devices

provide a Chip-Erase operation, which allows the user to

erase the entire memory array to the “1s” state. This is use-

ful when the entire device must be quickly erased.

The Chip-Erase operation is initiated by executing a six-

byte Software Data Protection command sequence with

Chip-Erase command (10H) with address 555H in the last

byte sequence. The internal Erase operation begins with

the rising edge of the sixth WE# or CE#, whichever occurs

first. During the internal Erase operation, the only valid read

is Toggle Bit or Data# Polling. See Table 4 for the com-

mand sequence, Figure 10 for the timing diagram, and Fig-

ure 19 for the flowchart. Any commands written during the

Chip-Erase operation will be ignored.

Write Operation Status Detection

The GLS29SF020/040 and GLS29VF020/040 devices

provide two software means to detect the completion of a

Write (Program or Erase) cycle, in order to optimize the

system Write cycle time. The software detection includes

two status bits: Data# Polling (DQ7) and Toggle Bit

(DQ6). The End-of-Write detection mode is enabled after

the rising edge of WE# which initiates the internal Pro-

gram or Erase operation.

The actual completion of the nonvolatile write is asyn-

chronous with the system; therefore, either a Data# Poll-

ing or Toggle Bit read may be simultaneous with the

completion of the Write cycle. If this occurs, the system

may possibly get an erroneous result, i.e., valid data may

appear to conflict with either DQ7 or DQ6. In order to pre-

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

vent spurious rejection, if an erroneous result occurs, the

software routine should include a loop to read the

accessed location an additional two (2) times. If both

reads are valid, then the device has completed the Write

cycle, otherwise the rejection is valid.

Data# Polling (DQ7)

When the GLS29SF020/040 and GLS29VF020/040

devices are in the internal Program operation, any

attempt to read DQ7 will produce the complement of the

true data. Once the Program operation is completed,

DQ7 will produce true data. Note that even though DQ7

may have valid data immediately following the comple-

tion of an internal Write operation, the remaining data

outputs may still be invalid: valid data on the entire data

bus will appear in subsequent successive Read cycles

after an interval of 1 µs. During internal Erase operation,

any attempt to read DQ7 will produce a ‘0’. Once the

internal Erase operation is completed, DQ7 will produce

a ‘1’. The Data# Polling is valid after the rising edge of

fourth WE# (or CE#) pulse for Program operation. For

Sector- or Chip-Erase, the Data# Polling is valid after the

rising edge of sixth WE# (or CE#) pulse. See Figure 7 for

Data# Polling timing diagram and Figure 17 for a flow-

chart.

Toggle Bit (DQ6)

During the internal Program or Erase operation, any con-

secutive attempts to read DQ6 will produce alternating ‘0’s

and ‘1’s, i.e., toggling between 0 and 1. When the internal

Program or Erase operation is completed, the toggling will

stop. The device is then ready for the next operation. The

Toggle Bit is valid after the rising edge of fourth WE# (or

CE#) pulse for Program operation. For Sector or Chip-

Erase, the Toggle Bit is valid after the rising edge of sixth

WE# (or CE#) pulse. See Figure 8 for Toggle Bit timing dia-

gram and Figure 17 for a flowchart.

Data Protection

The GLS29SF020/040 and GLS29VF020/040 devices

provide both hardware and software features to protect

nonvolatile data from inadvertent writes.

Hardware Data Protection

Noise/Glitch Protection: A WE# or CE# pulse of less than 5

ns will not initiate a Write cycle.

VDD Power Up/Down Detection: The Write operation is

inhibited when VDD is less than 2.5V for GLS29SF020/

040. The Write operation is inhibited when VDD is less than

1.5V. for GLS29VF020/040.

Write Inhibit Mode: Forcing OE# low, CE# high, or WE#

high will inhibit the Write operation. This prevents inadver-

tent writes during power-up or power-down.

Software Data Protection (SDP)

The GLS29SF020/040 and GLS29VF020/040 provide

the JEDEC approved Software Data Protection scheme for

all data alteration operations, i.e., Program and Erase. Any

Program operation requires the inclusion of a series of

three- byte sequence. The three-byte load sequence is

used to initiate the Program operation, providing optimal

protection from inadvertent Write operations, e.g., during

the system power-up or power-down. Any Erase operation

requires the inclusion of a six-byte load sequence. These

devices are shipped with the Software Data Protection per-

manently enabled. The specific software command codes

are shown in Table 4. During SDP command sequence,

invalid commands will abort the device to read mode,

within TRC.

Product Identification

The Product Identification mode identifies the devices as

GLS29SF020, GLS29SF040 and GLS29VF020,

GLS29VF040 and manufacturer as Greenliant. This mode

may be accessed by software operations. Users may use

the Software Product Identification operation to identify the

part (i.e., using the device ID) when using multiple manu-

facturers in the same socket. For details, see Table 4 for

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

software operation, Figure 11 for the Software ID Entry and

Read timing diagram, and Figure 18 for the Software ID

Entry command sequence flowchart.

Product Identification Mode Exit/Reset

In order to return to the standard Read mode, the Software

Product Identification mode must be exited. Exit is accom-

plished by issuing the Software ID Exit command

sequence, which returns the device to the Read operation.

Please note that the Software ID Exit command is ignored

during an internal Program or Erase operation. See Table 4

for software command codes, Figure 12 for timing wave-

form, and Figure 18 for a flowchart.

FIGURE 1: Functional Block Diagram

TABLE 1: Product Identification

Address Data

Manufacturer’s ID 0000H BFH

Device ID

GLS29SF020 0001H 24H

GLS29VF020 0001H 25H

GLS29SF040 0001H 13H

GLS29VF040 0001H 14H

T1.3 1160

Y-Decoder

I/O Buffers and Data Latches

1160 B1.0

Address Buffers & Latches

X-Decoder

DQ7 - DQ0

Memory

Address

OE#

CE#

WE#

SuperFlash

Memory

Control Logic

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

FIGURE 2: Pin Assignments for 32-lead PLCC

FIGURE 3: Pin Assignments for 32-lead TSOP (8mm x 14mm)

DQ0

A14

A13

A11

OE#

A10

CE#

DQ7

A14

A13

A11

OE#

A10

CE#

DQ7

4 3 2 1 32 31 30

A12

A15

A16

VDD

WE#

A17

A12

A15

A16

A18

VDD

WE#

A17

32-lead PLCC

To p V i e w

1160 32-plcc NH P1.2

14 15 16 17 18 19 20

DQ1

DQ2

VSS

DQ3

DQ4

DQ5

DQ6

DQ1

DQ2

VSS

DQ3

DQ4

DQ5

DQ6

GLS29SF/VF020GLS29SF/VF040 GLS29SF/VF020 GLS29SF/VF040

A11

A13

A14

A17

WE#

VDD

A16

A15

A12

A11

A13

A14

A17

WE#

VDD

A18

A16

A15

A12

GLS29SF/VF020GLS29SF/VF040 GLS29SF/VF020 GLS29SF/VF04

OE#

A10

CE#

DQ7

DQ6

DQ5

DQ4

DQ3

VSS

DQ2

DQ1

DQ0

OE#

A10

CE#

DQ7

DQ6

DQ5

DQ4

DQ3

VSS

DQ2

DQ1

DQ0

1160 32-tsop WH P2.2

Standard Pinout

Top View

Die Up

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

TABLE 2: Pin Description

Symbol Pin Name Functions

AMS1-A0

1. AMS = Most significant address

AMS = A17 for GLS29SF/VF020 and A18 for GLS29SF/VF040

Address Inputs To provide memory addresses. During Sector-Erase AMS-A8 address lines will select the

sector.

DQ7-DQ0Data Input/output To output data during Read cycles and receive input data during Write cycles.

Data is internally latched during a Write cycle.

The outputs are in tri-state when OE# or CE# is high.

CE# Chip Enable To activate the device when CE# is low.

OE# Output Enable To gate the data output buffers.

WE# Write Enable To control the Write operations.

VDD Power Supply To provide power supply voltage: 4.5-5.5V for GLS29SF020/040

2.7-3.6V for GLS29VF020/040

VSS Ground

NC No Connection Pin not connected internally

T2.5 1160

TABLE 3: Operation Modes Selection

Mode CE# OE# WE# DQ Address

Read VIL VIL VIH DOUT AIN

Program VIL VIH VIL DIN AIN

Erase VIL VIH VIL X1

1. X can be VIL or VIH, but no other value.

Sector address,

XXH for Chip-Erase

Standby VIH X X High Z X

Write Inhibit X VIL X High Z/ DOUT X

XXV

IH High Z/ DOUT X

Product Identification

Software Mode VIL VIL VIH See Table 4

T3.4 1160

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

TABLE 4: Software Command Sequence

Command

Sequence

1st Bus

Write Cycle

2nd Bus

Write Cycle

3rd Bus

Write Cycle

4th Bus

Write Cycle

5th Bus

Write Cycle

6th Bus

Write Cycle

Addr1Data Addr1Data Addr1Data Addr1Data Addr1Data Addr1Data

Byte-Program 555H AAH 2AAH 55H 555H A0H BA2Data

Sector-Erase 555H AAH 2AAH 55H 555H 80H 555H AAH 2AAH 55H SAX320H

Chip-Erase 555H AAH 2AAH 55H 555H 80H 555H AAH 2AAH 55H 555H 10H

Software ID Entry4,5 555H AAH 2AAH 55H 555H 90H

Software ID Exit6XXH F0H

Software ID Exit6555H AAH 2AAH 55H 555H F0H

T4.7 1160

1. Address format A14-A0 (Hex),

Addresses A15-AMS can be VIL or VIH, but no other value, for the Command sequence for GLS29SF/VF020/040.

AMS = Most significant address

AMS = A17 for GLS29SF/VF020 and A18 for GLS29SF/VF040.

2. BA = Program Byte address

3. SAX for Sector-Erase; uses AMS-A7 address lines for GLS29SF/VF020/040

4. The device does not remain in Software Product ID mode if powered down.

5. With AMS-A1 = 0; Greenliant Manufacturer’s ID = BFH, is read with A0 = 0,

GLS29SF020 Device ID = 24H, is read with A0 = 1

GLS29VF020 Device ID = 25H, is read with A0 = 1

GLS29SF040 Device ID = 13H, is read with A0 = 1

GLS29VF040 Device ID = 14H, is read with A0 = 1

6. Both Software ID Exit operations are equivalent

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

Absolute Maximum Stress Ratings (Applied conditions greater than those listed under “Absolute Maximum

Stress Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation

of the device at these conditions or conditions greater than those defined in the operational sections of this data

sheet is not implied. Exposure to absolute maximum stress rating conditions may affect device reliability.)

Temperature Under Bias . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55°C to +125°C

Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65°C to +150°C

D. C. Voltage on Any Pin to Ground Potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to VDD+0.5V

Transient Voltage (<20 ns) on Any Pin to Ground Potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -2.0V to VDD+2.0V

Voltage on A9 Pin to Ground Potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 13.2V

Package Power Dissipation Capability (TA = 25°C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0W

Through Hole Lead Soldering Temperature (10 Seconds) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300°C

Surface Mount Solder Reflow Temperature1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C for 10 seconds

Output Short Circuit Current2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA

1. Excluding certain with-Pb 32-PLCC units, all packages are 260°C capable in both non-Pb and with-Pb solder versions.

Certain with-Pb 32-PLCC package types are capable of 240°C for 10 seconds; please consult the factory for the latest information.

2. Outputs shorted for no more than one second. No more than one output shorted at a time.

Operating Range for GLS29SF020/040

Range Ambient Temp VDD

Commercial 0°C to +70°C 4.5-5.5V

Industrial -40°C to +85°C 4.5-5.5V

Operating Range for GLS29VF020/040

Range Ambient Temp VDD

Commercial 0°C to +70°C 2.7-3.6V

Industrial -40°C to +85°C 2.7-3.6V

AC Conditions of Test

Input Rise/Fall Time . . . . . . . . . . . . . . 5 ns

Output Load . . . . . . . . . . . . . . . . . . . . . CL = 30 pF for 55 ns

Output Load . . . . . . . . . . . . . . . . . . . . . CL = 100 pF for 70 ns

See Figures 13, 14, and 15

TABLE 5: DC Operating Characteristics VDD = 4.5-5.5V for GLS29SF020/040

Symbol Parameter

Limits

Test ConditionsMin Max Units

IDD Power Supply Current Address input=VIL/VIH, at f=1/TRC Min

VDD=VDD Max

Read 25 mA CE#=OE#=VIL, WE#=VIH, all I/Os open

Write 30 mA CE#=WE#=VIL, OE#=VIH

ISB1 Standby VDD Current (TTL input) 3 mA CE#=VIH, VDD=VDD Max

ISB2 Standby VDD Current (CMOS input) 100 µA CE#=VIHC, VDD=VDD Max

ILI Input Leakage Current 1 µA VIN=GND to VDD, VDD=VDD Max

ILO Output Leakage Current 10 µA VOUT=GND to VDD, VDD=VDD Max

VIL Input Low Voltage 0.8 V VDD=VDD Min

VIH Input High Voltage 2.0 V VDD=VDD Max

VIHC Input High Voltage (CMOS) VDD-0.3 V VDD=VDD Max

VOL Output Low Voltage 0.4 V IOL=2.1 µA, VDD=VDD Min

VOH Output High Voltage 2.4 V IOH=-400 µA, VDD=VDD Min

T5.7 1160

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

TABLE 6: DC Operating Characteristics VDD = 2.7-3.6V for GLS29VF020/040

Symbol Parameter

Limits

Test ConditionsMin Max Units

IDD Power Supply Current Address input=VIL/VIH, at f=1/TRC Min

VDD=VDD Max

Read 25 mA CE#=OE#=VIL, WE#=VIH, all I/Os open

Write 30 mA CE#=WE#=VIL, OE#=VIH

ISB Standby VDD Current 30 µA CE#=VIHC, VDD=VDD Max

ILI Input Leakage Current 1 µA VIN=GND to VDD, VDD=VDD Max

ILO Output Leakage Current 10 µA VOUT=GND to VDD, VDD=VDD Max

VIL Input Low Voltage 0.8 V VDD=VDD Min

VIH Input High Voltage 0.7VDD VV

DD=VDD Max

VIHC Input High Voltage (CMOS) VDD-0.3 V VDD=VDD Max

VOL Output Low Voltage 0.2 V IOL=100 µA, VDD=VDD Min

VOH Output High Voltage VDD-0.2 V IOH=-100 µA, VDD=VDD Min

T6.9 1160

TABLE 7: Recommended System Power-up Timings

Symbol Parameter Minimum Units

TPU-READ1Power-up to Read Operation 100 µs

TPU-WRITE1Power-up to Program/Erase Operation 100 µs

T7.1 1160

1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter.

TABLE 8: Capacitance (TA = 25°C, f=1 Mhz, other pins open)

Parameter Description Test Condition Maximum

CI/O1I/O Pin Capacitance VI/O = 0V 12 pF

CIN1Input Capacitance VIN = 0V 6 pF

T8.1 1160

1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter.

TABLE 9: Reliability Characteristics

Symbol Parameter Minimum Specification Units Test Method

NEND1Endurance 10,000 Cycles JEDEC Standard A117

TDR1Data Retention 100 Years JEDEC Standard A103

ILTH1Latch Up 100 + IDD mA JEDEC Standard 78

T9.2 1160

1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter.

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

AC CHARACTERISTICS

TABLE 10: Read Cycle Timing Parameters

VDD = 4.5-5.5V for GLS29SF020/040 and 2.7-3.6V for GLS29VF020/040

Symbol Parameter

GLS29SF020/040-55 GLS29VF020/040-70

UnitsMin Max Min Max

TRC Read Cycle Time 55 70 ns

TCE Chip Enable Access Time 55 70 ns

TAA Address Access Time 55 70 ns

TOE Output Enable Access Time 30 35 ns

TCLZ1

1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter.

CE# Low to Active Output 0 0 ns

TOLZ1OE# Low to Active Output 0 0 ns

TCHZ1CE# High to High-Z Output 20 25 ns

TOHZ1OE# High to High-Z Output 20 25 ns

TOH1Output Hold from Address Change 00ns

T10.10 1160

TABLE 11: Program/Erase Cycle Timing Parameters

VDD = 4.5-5.5V for GLS29SF020/040 and 2.7-3.6V for GLS29VF020/040

Symbol Parameter Min Max Units

TBP Byte-Program Time 20 µs

TAS Address Setup Time 0 ns

TAH Address Hold Time 30 ns

TCS WE# and CE# Setup Time 0 ns

TCH WE# and CE# Hold Time 0 ns

TOES OE# High Setup Time 0 ns

TOEH OE# High Hold Time 10 ns

TCP CE# Pulse Width 40 ns

TWP WE# Pulse Width 40 ns

TWPH1

1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter.

WE# Pulse Width High 30 ns

TCPH1CE# Pulse Width High 30 ns

TDS Data Setup Time 40 ns

TDH1Data Hold Time 0 ns

TIDA1Software ID Access and Exit Time 150 ns

TSE Sector-Erase 25 ms

TSCE Chip-Erase 100 ms

T11.9 1160

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

FIGURE 4: Read Cycle Timing Diagram

FIGURE 5: WE# Controlled Program Cycle Timing Diagram

1160 F03.1

ADDRESS AMS-0

DQ7-0

WE#

OE#

CE#

TCE

TRC TAA

TOE

TOLZ

VIH

HIGH-Z

TCLZ TOH TCHZ

HIGH-Z

D ATA V ALIDD ATA V ALID

TOHZ

Note: AMS = Most significant address

AMS = A17 for GLS29SF/VF020 and A18 for GLS29SF/VF040

1160 F04.1

ADDRESS AMS-0

DQ7-0

TDH

TWPH TDS

TWP

TAH

TAS

TCH

TCS

CE#

SW0 SW1 SW2

555 2AA 555 ADDR

AA 55 A0 DATA

BYTE

(ADDR/DATA)

OE#

WE#

TBP

INTERNAL PROGRAM OPERATION STARTS

Note: AMS = Most significant address

AMS = A17 for GLS29SF/VF020 and A18 for GLS29SF/VF040

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

FIGURE 6: CE# Controlled Program Cycle Timing Diagram

FIGURE 7: Data# Polling Timing Diagram

1160 F05.1

ADDRESS AMS-0

DQ7-0

TDH

TCPH TDS

TCP

TAH

TAS

TCH

TCS

WE#

SW0 SW1 SW2

555 2AA 555 ADDR

AA 55 A0 DATA

INTERNAL PROGRAM OPERATION STARTS

BYTE

(ADDR/DATA)

OE#

CE#

TBP

Note: AMS = Most significant address

AMS = A17 for GLS29SF/VF020 and A18 for GLS29SF/VF040

1160 F06.1

ADDRESS AMS-0

DQ7DD# D# D

WE#

OE#

CE#

TOEH

TOE

TCE

TOES

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

FIGURE 8: Toggle Bit Timing Diagram

FIGURE 9: WE# Controlled Sector-Erase Timing Diagram

1160 F07.1

ADDRESS AMS-0

DQ6

WE#

OE#

CE#

TOE

TOEH

TCE

TOES

TWO READ CYCLES

WITH SAME OUTPUTS

Note: AMS = Most significant address

AMS = A17 for GLS29SF/VF020 and A18 for GLS29SF/VF040

1160 F08.1

ADDRESS A

MS-0

7-0

WE#

SW0 SW1 SW2 SW3 SW4 SW5

555 2AA 2AA555 555

55 2055AA 80 AA

OE#

CE#

SIX-BYTE CODE FOR SECTOR-ERASE

Note: This device also supports CE# controlled Sector-Erase operation The WE# and CE# signals are interchangeable as

long as minimum timings are met. (See Table 11)

AMS = Most significant address

AMS = A17 for GLS29SF/VF020 and A18 for GLS29SF/VF040

SAX = Sector Address.

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

FIGURE 10: WE# Controlled Chip-Erase Timing Diagram

FIGURE 11: Software ID Entry and Read

1160 F09.1

ADDRESS AMS-0

DQ7-0

WE#

SW0 SW1 SW2 SW3 SW4 SW5

555 2AA 2AA555 555

55 1055AA 80 AA

555

OE#

CE#

SIX-BYTE CODE FOR CHIP-ERASE

TSCE

TWP

Note: This device also supports CE# controlled Chip-Erase operation The WE# and CE# signals are interchangeable as

long as minimum timings are met. (See Table 11)

AMS = Most significant address

AMS = A17 for GLS29SF/VF020 and A18 for GLS29SF/VF040

1160 F10.1

ADDRESS A14-0

DQ7-0

WE#

SW1SW0 SW2

Device ID

555 2AA 555 0000 0001

OE#

CE#

Three-Byte Sequence for

Software ID Entry

TWP

TWPH TAA

BF55AA 90

TIDA

Note: Device ID = 24H for GLS29SF020, 13H for GLS29SF040

25H for GLS29VF020, 14H for GLS29VF040

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

FIGURE 12: Software ID Exit and Reset

1160 F11.1

ADDRESS A14-0

DQ7-0

TIDA

TWP

TWHP

WE#

SW0 SW1 SW2

555 2AA 555

Three-Byte Sequence for

Sofware ID Exit and Reset

OE#

CE#

AA 55 F0

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

FIGURE 13: AC Input/Output Reference Waveforms for GLS29SF020/040

FIGURE 14: AC Input/Output Reference Waveforms for GLS29VF020/040

1160 F12.0

REFERENCE POINTS OUTPUTINPUT VIT

VIHT

VILT

VOT

AC test inputs are driven at VIHT (3.0V) for a logic “1” and VILT (0V) for a logic “0”. Measurement reference points for

inputs and outputs are VIT (1.5 VDD) and VOT (1.5 VDD). Input rise and fall times (10%  90%) are <10 ns.

Note: VIT - VINPUT Te s t

VOT - VOUTPUT Test

VIHT - VINPUT HIGH Test

VILT - VINPUT LOW Test

1160 F12.0

REFERENCE POINTS OUTPUTINPUT VIT

VIHT

VILT

VOT

AC test inputs are driven at VIHT (0.9 VDD) for a logic “1” and VILT (0.1 VDD) for a logic “0”. Measurement reference points

for inputs and outputs are VIT (0.5 VDD) and VOT (0.5 VDD). Input rise and fall times (10%  90%) are <5 ns.

Note: VIT - VINPUT Te st

VOT - VOUTPUT Test

VIHT - VINPUT HIGH Test

VILT - VINPUT LOW Test

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

FIGURE 15: Test Load Examples

1160 F14a.0

GLS29SF040

TO TESTER

TO DUT

CLRL LOW

RL HIGH

VDD

1160 F14b.0

TO TESTER

O DUT

GLS29VF040

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

FIGURE 16: Byte-Program Algorithm

1160 F15.0

Start

Load data: AAH

Address: 555H

Load data: 55H

Address: 2AAH

Load data: A0H

Address: 555H

Load Byte

Address/Byte

Data

Wait for end of

Program (TBP,

Data# Polling

bit, or Toggle bit

operation)

Program

Completed

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

FIGURE 17: Wait Options

1160 F16.0

W ait TBP,

TSCE, or TSE

Byte-

Program/Erase

Initiated

Internal Timer Toggle Bit

Yes

Program/Erase

Completed

Does DQ6

match?

Read same

byte

Data# Polling

Program/Erase

Completed

Program/Erase

Completed

Read byte

Is DQ7 =

true data?

Read DQ7

Byte-

Program/Erase

Initiated

Byte-

Program/Erase

Initiated

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

FIGURE 18: Software ID Command Flowcharts

1160 F17.0

Load data: AAH

Address: 555H

Software ID Entry

Command Sequence

Load data: 55H

Address: 2AAH

Load data: 90H

Address: 555H

W ait TIDA

Read Software ID

Load data: AAH

Address: 555H

Software ID Exit &

Reset Command Sequence

Load data: 55H

Address: 2AAH

Load data: F0H

Address: 555H

Load data: F0H

Address: XXH

Return to normal

operation

W ait TIDA

Return to normal

operation

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

FIGURE 19: Erase Command Sequence

1160 F18.0

Load data: AAH

Address: 555H

Chip-Erase

ommand Sequence

Load data: 55H

Address: 2AAH

Load data: 80H

Address: 555H

Load data: 55H

Address: 2AAH

Load data: 10H

Address: 555H

Load data: AAH

Address: 555H

W ait TSCE

Chip erased

to FFH

Load data: AAH

Address: 555H

Sector-Erase

Command Sequence

Load data: 55H

Address: 2AAH

Load data: 80H

Address: 555H

Load data: 55H

Address: 2AAH

Load data: 20H

Address: SAX

Load data: AAH

Address: 555H

W ait TSE

Sector erased

to FFH

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

PRODUCT ORDERING INFORMATION

Device Speed Suffix1 Suffix2

GLS29xFxxx - XXX -XX-XXX

Environmental Attribute

E1 = non-Pb

Package Modifier

H = 32 leads

Package Type

N = PLCC

W = TSOP (type 1, die up, 8mm x 14mm)

Temperature Range

C = Commercial = 0°C to +70°C

I = Industrial = -40°C to +85°C

Minimum Endurance

4 = 10,000 cycles

Read Access Speed

55 = 55 ns

70 = 70 ns

Device Density

040 = 4 Mbit

020 = 2 Mbit

Function

F = Chip- or Sector-Erase

Byte-Program

Voltage

S = 4.5-5.5V

V = 2.7-3.6V

1. Environmental suffix “E” denotes non-Pb solder.

Greenliant non-Pb solder devices are “RoHS Compliant”.

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

Valid combinations for GLS29SF020

GLS29SF020-55-4C-NHE GLS29SF020-55-4C-WHE

GLS29SF020-55-4I-NHE GLS29SF020-55-4I-WHE

Valid combinations for GLS29VF020

GLS29VF020-70-4C-NHE GLS29VF020-70-4C-WHE

GLS29VF020-70-4I-NHE GLS29VF020-70-4I-WHE

Valid combinations for GLS29SF040

GLS29SF040-55-4C-NH GLS29SF040-55-4C-WH

GLS29SF040-55-4C-NHE GLS29SF040-55-4C-WHE

GLS29SF040-55-4I-NH GLS29SF040-55-4I-WH

GLS29SF040-55-4I-NHE GLS29SF040-55-4I-WHE

Valid combinations for GLS29VF040

GLS29VF040-70-4C-NH GLS29VF040-70-4C-WH

GLS29VF040-70-4C-NHE GLS29VF040-70-4C-WHE

GLS29VF040-70-4I-NH GLS29VF040-70-4I-WH

GLS29VF040-70-4I-NHE GLS29VF040-70-4I-WHE

Note: Valid combinations are those products in mass production or will be in mass production. Consult your Greenliant sales

representative to confirm availability of valid combinations and to determine availability of new combinations.

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

PACKAGING DIAGRAMS

FIGURE 20: 32-lead Plastic Lead Chip Carrier (PLCC)

Greenliant Package Code: NH

.040

.030

.021

.013 .530

.490

.095

.075

.140

.125

.032

.026

.032

.026

.029

.023

.453

.447

.553

.547

.595

.585

.495

.485 .112

.106

.042

.048

.042

.015 Min.

T OP VIEW SIDE VIEW BO TT OM VIEW

1232

.400

BSC

32-plcc-NH

-3

ote: 1. Complies with JEDEC publication 95 MS-016 AE dimensions, although some dimensions may be more stringent.

2. All linear dimensions are in inches (max/min).

3. Dimensions do not include mold flash. Maximum allowable mold flash is .008 inches.

4. Coplanarity: 4 mils.

.050

BSC

.050

BSC

Optional

Pin #1

dentifier .020 R.

MAX. R.

x 30°

Greenliant, the Greenliant logo and NANDrive are trademarks of Greenliant Systems, Ltd.

SSF is a trademark and SuperFlash is a registered trademark of Silicon Storage Technology, Inc., a wholly owned subsidiary of

Microchip Technology Inc.

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

FIGURE 21: 32-lead Thin Small Outline Package (TSOP) 8mm x 14mm

Greenliant Package Code: WH

32-tsop-WH

-7

ote: 1. Complies with JEDEC publication 95 MO-142 BA dimensions,

although some dimensions may be more stringent.

2. All linear dimensions are in millimeters (max/min).

3. Coplanarity: 0.1 mm

4. Maximum allowable mold flash is 0.15 mm at the package ends, and 0.25 mm between leads.

1.20

max.

1mm

Pin # 1 Identifier

12.50

12.30

14.20

13.80

0.70

0.50

8.10

7.90 0.27

0.17

0.50

BSC

1.05

0.95

0.15

0.05

0.70

0.50

0°- 5°

DETAIL

Data Sheet

2 Mbit / 4 Mbit Small-Sector Flash

GLS29SF020 / GLS29SF040

GLS29VF020 / GLS29VF040

TABLE 12: Revision History

Number Description Date

05 •2002 Data Book May 2002

06 •Removed 512 Kbit, 1 Mbit, and 2 Mbit parts

•Commercial temperature and 70 ns parts removed

•PH package is no longer offered

•Part number changes - see page 24 for additional information

•Changes to Tables 5 and 6 on page 8 and page 10:

– Clarified Test Conditions for Power Supply Current and Read parameters

– Clarified IDD Write to be Program and Erase

– Corrected IDD Program and Erase from 20 mA to 30 mA

– Corrected IDD Read from 20 mA to 25 mA

•Clarified measurement reference points VIT and VOT to be 1.5V instead of 1.5VDD

•Corrected the VOL test condition IOL to be 2.1 mA instead of 2.1 µA in Table 5 on page 8

Mar 2003

07 •Corrected the Test Conditions for the Read Parameter in Table 5 on page 8 Apr 2003

08 •Added Commercial temperatures for all packages (See page 24 for details) Aug 2003

09 •2004 Data Book

•Changed status to “Data Sheet”

Dec 2003

10 •Added 70 ns technical data and MPNs for SST29VF040 only Feb 2004

11 •Added RoHS compliance information on page 1 and in the

“Product Ordering Information” on page 23

•Reinstated 512 Kbit, 1 Mbit, and 2 Mbit devices and MPNs (excluding the PDIP pack-

age)

•Removed 55 ns technical data and MPNs for SST29VF040

•Added non-Pb MPNs for all devices

•Clarified the solder temperature profile under “Absolute Maximum Stress Ratings” on

page 8

Mar 2005

12 •Removed all entries related to SST29SF/VF512 and SST29SF/VF010

•Removed leaded parts for 020 products.

Nov 2005

13 •Changed IDD Read from 20mA to 25mA, and Changed IDD Write from 20mA to 30mA in

Table 5 on page 8 and Table 6 on page 10

Oct 2006

14 •Changed ISB from 15 to 30 µA in Table 6 on page 10. Oct 2008

15 •Transferred from SST to Greenliant May 2010

Greenliant, the Greenliant logo and NANDrive are trademarks of Greenliant Systems, Ltd.

All trademarks and registered trademarks are the property of their respective owners.

These specifications are subject to change without notice.

SSF is a trademark and SuperFlash is a registered trademark of Silicon Storage Technology, Inc., a wholly owned subsidiary of

Microchip Technology Inc.