SW001A0C91Z - GE - Datasheet.Directory

Data Sheet

October 5, 2009

SW/SC001/003 Series DC-DC Converter Power Modules:

18-36V & 36-75Vdc Input; 3.3V-15Vdc Output; 1-3.5A Output Current

§ This product is intended for integration into end-use equipment. All of the required procedures of end-use equipment should be followed.

* UL is a registered trademark of Underwriters Laboratories, Inc.

† CSA is a registered trademark of Canadian Standards Association.

‡ VDE is a trademark of Verband Deutscher Elektrotechniker e.V.

** ISO is a registered trademark of the International Organization of Standards

Document No: DS03-086 ver. 1.91

PDF name: sw001-002-003_series.pdf

Applications

 Wireless Networks

 Distributed power architectures

 Optical and Access Network Equipment

 Enterprise Networks

 Latest generation IC’s (DSP, FPGA, ASIC)

and Microprocessor powered applications

Options

 Remote On/Off logic (positive or negative), pin

optional for TH version (Suffix 1 or 4)

 Output voltage adjustment-Trim, pin optional

for TH version (Suffix 9)

 Surface Mount/Tape and Reel (-SR Suffix)

Features

 Compliant to RoHS EU Directive 2002/95/EC (-Z

versions)

 Compliant to ROHS EU Directive 2002/95/EC with

lead solder exemption (non-Z versions)

 Delivers up to 3.5A Output current

15V (1A), 12V (1.25A), 5.0V (3A) and 3.3V (3.5A)

 High efficiency – 86% at 5.0V full load (VIN=54 Vdc)

 Low output ripple and noise

 Small Size and low profile

27.94mm x 24.38mm x 8.5mm

(1.10 x 0.96 x 0.335 in)

 Industry Standard pin-out:

TH version is LW series compatible

 Surface mount (SMT) or Through hole (TH)

 Remote On/Off (optional pin on TH version)

 Output overcurrent/voltage protection

 Single Tightly regulated output

 Output voltage adjustment trim ±10%

 Wide operating temperature range (-40°C to 85°C)

 Meets the voltage insulation requirements for ETSI

300-132-2 and complies with and is Licensed for

Basic Insulation rating per EN 60950

 CE mark meets the 2006/95/EC directive§

 UL* 60950-1Recognized, CSA† C22.2 No. 60950-1-

03 Certified, and VDE‡ 0805: (IEC60950, 3rd

Edition) Licensed

 ISO** 9001 and ISO 14001 certified manufacturing

facilities

 Approved for Basic Insulation

Description

The SW/SC series power modules are isolated dc-dc converters that operate over a wide range of input voltage (VIN

= 18 - 36Vdc for SC modules and VIN = 36 – 75Vdc for SW modules) and provide a single precisely regulated

output. This series is a low cost, smaller size alternative to the existing LW/LAW/LC with enhanced performance

parameters. The output is fully isolated from the input, allowing versatile polarity configurations and grounding

connections. The modules exhibit high efficiency, typical efficiency of 86% for 5.0V/3A. Built-in filtering for both

input and output minimizes the need for external filtering.

RoHS Compliant

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

LINEAGE POWER 2

Absolute Maximum Ratings

Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are

absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in

excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for

extended periods can adversely affect the device reliability.

Parameter Device Symbol Min Max Unit

Input Voltage (Continuous) SW VIN -0.3 80 Vdc

SC VIN -0.3 50

Transient (100ms) All VIN, trans -0.3 100 Vdc

Operating Ambient Temperature All TA -40 85 °C

(see Thermal Considerations section)

Storage Temperature All Tstg -55 125 °C

I/O Isolation Voltage (100% factory Hi-Pot tested) All ⎯ ⎯ 2250 Vdc

Electrical Specifications

Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature

conditions.

Parameter Device Symbol Min Typ Max Unit

Operating Input Voltage SW VIN 36 54 75 Vdc

SC VIN 18 27 36 Vdc

Maximum Input Current (VIN=0V to 75V, IO=IO, max) SW IIN,max 0.6 Adc

(VIN=0V to 36V, IO=IO, max) SC IIN,max 1.2 Adc

Inrush Transient All I2t 0.05 A2s

Input Reflected Ripple Current, peak-to-peak

(5Hz to 20MHz, 12μH source impedance; VIN=0V to

75V, IO= IOmax ; see Test configuration section)

All 30 mAp-p

Input Ripple Rejection (120Hz) All 50 dB

EMC, EN55022 See EMC Considerations section

CAUTION: This power module is not internally fused. An input line fuse must always be used.

This power module can be used in a wide variety of applications, ranging from simple standalone operation to being

part of complex power architecture. To preserve maximum flexibility, internal fusing is not included; however, to

achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-

acting fuse with a maximum rating of 3A (see Safety Considerations section). Based on the information provided in

this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be

used. Refer to the fuse manufacturer’s data sheet for further information.

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

LINEAGE POWER 3

Electrical Specifications (continued)

Parameter Device Symbol Min Typ Max Unit

Output Voltage Set-point All VO, set -1.5 ⎯ +1.5 % VO, set

(VIN=VIN,nom, IO=IO, max, TA=25°C)

Output Voltage VO -3.0 ⎯ +3.0 % VO, set

(Over all operating input voltage, resistive

load, and temperature conditions until end

of life)

Adjustment Range All VO, adj -10.0 +10.0 % VO, set

Selected by external resistor

Output Regulation

Line (VIN=VIN, min to VIN, max) All

⎯ 0.05 0.2 % VO, set

Load (IO=IO, min to IO, max) All

⎯ 0.05 0.2 % VO, set

Temperature (Tref=TA, min to TA, max) All

⎯ ⎯ 1.00 % VO, set

Output Ripple and Noise on nominal output

Measured with 10uF Tantalum and 1uF

ceramic

(VIN=VIN, nom IO=80%IO, max TA=25°C)

RMS (5Hz to 20MHz bandwidth) 5V, 3.3V ⎯ ⎯ 25 mVrms

Peak-to-Peak (5Hz to 20MHz bandwidth) 5V, 3.3V ⎯ ⎯ 75 mVpk-pk

RMS (5Hz to 20MHz bandwidth) 15V, 12V ⎯ ⎯ 35 mVrms

Peak-to-Peak (5Hz to 20MHz bandwidth) 15V, 12V ⎯ ⎯ 100 mVpk-pk

External Capacitance 3.3V, 5V CO, max 0 ⎯ 1000 μF

12V, 15V CO, max 0 ⎯ 220 μF

Output Current 15V Io 0 ⎯ 1.0 Adc

12V Io 0 ⎯ 1.25 Adc

5V Io 0 ⎯ 3.0 Adc

3.3V Io 0 ⎯ 3.5 Adc

Output Current Limit Inception 15V IO, lim 1.1 ⎯ ⎯ Adc

(Hiccup Mode) 12V IO, lim 1.4 ⎯ ⎯ Adc

5V IO, lim 3.2 4.2 ⎯ Adc

3.3V IO, lim 3.7 ⎯ ⎯ Adc

Output Short-Circuit Current 15V IO, s/c ⎯ ⎯ 0.8 A rms

VO ≤ 250 mV @ 25o C 12V IO, s/c ⎯ ⎯ 1.2 A rms

5V IO, s/c ⎯ ⎯ 0.7 A rms

3.3V IO, s/c ⎯ ⎯ 1.5 A rms

Efficiency SW (15V) η ⎯ 88.0 ⎯ %

VIN=VIN, nom, TA=25°C SW (12V) η ⎯ 87.0 ⎯ %

IO=IO, max, VO= VO, set SW (5.0V) η ⎯ 86.0 ⎯ %

SW (3.3V) η ⎯ 85.0 ⎯ %

SC (12V) η ⎯ 85.0 ⎯

SC (5.0V) η ⎯ 85.5 ⎯

SC (3.3V) η ⎯ 85.5 ⎯

Switching Frequency (Variable with Line &

Load

)

VIN=VIN, nom and IO= IO, max All fsw ⎯ 300 ⎯ kHz

VIN=VIN, nom and IO= 0.5 x IO, max All fsw ⎯ 440 ⎯ kHz

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

LINEAGE POWER 4

Electrical Specifications (continued)

Parameter Device Symbol Min Typ Max Unit

Dynamic Load Response

(ΔIo/Δt=0.1A/μs, VIN=VIN, nom, TA=25°C)

Load Change from Io= 50% to 75% or

25% to 50% of Io,max:

Peak Deviation All Vpk ⎯ 1.5 ⎯ % VO, set

Settling Time (Vo<10% peak deviation) All ts ⎯ 800 ⎯ μs

Isolation Specifications

Parameter Symbol Min Typ Max Unit

Isolation Capacitance Ciso ⎯ 65 ⎯ pF

Isolation Resistance Riso 10 ⎯ ⎯ MΩ

I/O Isolation Voltage All ⎯ ⎯ 2250 Vdc

General Specifications

Parameter Min Typ Max Unit

Calculated MTBF (for SW003A0A91 in accordance with Lineage

Power RIN: IO=80% of IO, max, TA=25°C, airflow=1m/s) 8,200,000 Hours

Weight ⎯ 9.0 (0.32) ⎯ g (oz.)

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

LINEAGE POWER 5

Feature Specifications

Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature

conditions. See Feature Descriptions for additional information.

Parameter Device Symbol Min Typ Max Unit

Remote On/Off Signal Interface

(VIN=VIN, min to VIN, max ; open collector or equivalent,

Signal referenced to VIN- terminal)

Negative Logic: device code suffix “1”

Logic Low = module On, Logic High = module Off

Positive Logic: No device code suffix required

Logic Low = module Off, Logic High = module On

Logic Low - Remote On/Off Current All Ion/off ⎯ ⎯ 1.0 mA

Logic Low - On/Off Voltage All Von/off -0.7 ⎯ 1.2 V

Logic High Voltage – (Typ = Open Collector) All Von/off ⎯ 5.8 15 V

Logic High maximum allowable leakage current All Ion/off ⎯ ⎯ 50 μA

Turn-On Delay and Rise Times

(IO=80% of IO, max, TA=25°C)

Case 1: On/Off input is set ON and then input

power is applied (Tdelay = from instant at which

VIN=VIN, min until VO = 10% of VO, set).

All Tdelay

Case1 ⎯ 20 50 ms

Case 2: Input power is applied for at least 1

second and then On/Off input is set from OFF to

ON (Tdelay = from instant at which VIN=VIN, min until

VO = 10% of VO, set).

All Tdelay

Case2 ⎯ 20 50 ms

T rise = time for VO to rise from 10% of VO, set to

90% of VO, set. All Trise ⎯ 0.1 1 ms

T rise = time for VO to rise from 10% of VO, set to

90% of VO, set with max ext capacitance All Trise ⎯ 1.5 ⎯ ms

Output Voltage Overshoot 3 % VO, set

(IO=80% of IO, max, VIN= 54V, TA=25°C)

Output Overvoltage Protection 15V VO, limit 16.6 ⎯ 21.0 V

12V VO, limit 13.3 ⎯ 16.0 V

5.0V VO, limit 5.6 ⎯ 7.0 V

3.3V VO, limit 3.7 ⎯ 5.4 V

Input Undervoltage Lockout

Turn-on Threshold SW Vuv/on ⎯ 33 36 V

Turn-off Threshold SW Vuv/off 27.5 30.5 ⎯ V

Hysterisis SW Vhyst ⎯ 2.5 ⎯ V

Turn-on Threshold SC Vuv/on ⎯ 17 18 V

Turn-off Threshold SC Vuv/off 13.5 14.5 ⎯ V

Hystersis SC Vhyst ⎯ 3.0 ⎯ V

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

LINEAGE POWER 6

Characteristic Curves

The following figures provide typical characteristics for the SW001A0C91 (15.0V, 1A) at 25ºC. The figures are

identical for either positive or negative Remote On/Off logic.

0 0.2 0.4 0.6 0.8 1

= 3 6V

= 54 V

= 75V

EFFICIENCY (%)

OUTPUT CURRENT, Io (A)

On/Off VOLTAGE, OUTPUT VOLTAGE

VON/OFF(V) (2V/div) VO (V) (5V/div)

TIME, t (5ms/div)

Figure 1. Converter Efficiency ver sus Ou tpu t

Current. Figure 4. Typical Start-Up Using Remote On/Off,

negative logic version shown.

0.0

0.2

0.4

0.6

0.8

1. 0

1. 2

0 102030405060708090100110

3.0 m/ s (600 f t ./ min.)

2.0 m/ s (400 f t ./ min.)

1.0 m/ s (200 f t ./ min.)

Nat ural Convect ion

OUTPUT CURRENT, Io (A)

AMBIENT TEMPERATURE, TA OC

OUTPUT VOLTAGE, OUTPUTCURRENT

VO (V) (50mV/div), IO (A) (0.2A/div)

TIME, t (1ms/div)

Figure 2. Derating Output Current versus Local

Ambien t Temperature and Airflow. Figure 5. Transient Response to Dynamic Load Chang e

from 50% to 75% to 50% of full load.

OUTPUT VOLTAGE,

VO (V) (20mV/div)

TIME, t (1μs/div)

OUTPUT VOLTAGE

VO (V) (2.5V/div)

TIME, t (500μs/div)

Figure 3. Typical Output Ripple and Noise, VIN=VIN,

nom IO=80% of IO, max. Figure 6. Typical Start-Up Output Voltage Rise

Characteristic.

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

LINEAGE POWER 7

Characteristic Curves (continued)

The following figures provide typical characteristics for the SW001A2B91 (12.0V, 1.2A) at 25ºC. The figures are

identical for either positive or negative Remote On/Off logic.

0.0 0.2 0.4 0.6 0.8 1.0 1.2

= 36V

VI = 54 V

= 75V

EFFICIENCY (%)

OUTPUT CURRENT, Io (A)

On/Off VOLTAGE, OUTPUT VOLTAGE

VON/OFF(V) (2V/div) VO (V) (5V/div)

TIME, t (5ms/div)

Figure 7. Converter Efficiency Vs Load at Vo= 12 V. Figure 10. Typical Start-Up Using Remote On/Off,

negative logic version shown.

0.0

0.2

0.4

0.6

0.8

1. 0

1. 2

1. 4

0 10 20 3040 5060 7080 90100110

3.0 m/s (600 ft./min.)

2.0 m/s (400 ft./min.)

1.0 m/s (200 ft./min.)

Nat ural C o nvect i o n

OUTPUT CURRENT, Io (A)

AMBIENT TEMPERATURE, TA OC

OUTPUT VOLTAGE, OUTPUTCURRENT

VO (V) (50mV/div), IO (A) (0.25A/div)

TIME, t (1.0ms/div)

Figure 8. Derating Output Current versus Local

Ambien t Temperature and Airflow. Figure 11. Transient Response to Dynamic Load

Change from 50% to 75% to 50% of full load.

OUTPUT VOLTAGE,

VO (V) (50mV/div)

TIME, t (1μs/div)

OUTPUT VOLTAGE

VO (V) (2V/div)

TIME, t (100μs/div)

Figure 9. Typical Output Ripple and Noise, VIN=VIN,

nom IO=80% of IO, max. Figure 12. Typical Start-Up Output Voltage Rise

Characteristic.

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

LINEAGE POWER 8

Characteristic Curves (continued)

The following figures provide typical characteristics for the SW003A0A91 (5.0V, 3A) at 25ºC. The figures are identical

for either positive or negative Remote On/Off logic.

00.

11.522.

= 3 6V

= 54 V

= 75V

EFFICIENCY (%)

OUTPUT CURRENT, Io (A)

On/Off VOLTAGE, OUTPUT VOLTAGE

VON/OFF(V) (2V/div) VO (V) (2V/div)

TIME, t (5ms/div)

Figure 13. Converter Efficiency Vs Load at Vo= 5V. Figure 16. Typical Start-Up Using Remote On/Off,

negative logic version shown.

0 10 203040 50 60 708090100110

3.0 m/s (600 ft./min.)

2.0 m/s (400 ft./min.)

1.0 m/s (200 ft./min.)

Nat ural Co nvect i o n

OUTPUT CURRENT, Io (A)

AMBIENT TEMPERATURE, TA OC

OUTPUT VOLTAGE, OUTPUTCURRENT

VO (V) (50mV/div), IO (A) (0.5A/div)

TIME, t (1.0ms/div)

Figure 14. Derating Output Current versus Local

Ambien t Temperature and Airflow. Figure 17. Transient Response to Dynamic Load

Change from 50% to 75% to 50% of full load.

OUTPUT VOLTAGE,

VO (V) (20mV/div)

TIME, t (1μs/div)

OUTPUT VOLTAGE

VO (V) (1V/div)

TIME, t (100μs/div)

Figure 15. Typical Output Ripple and Noise, VIN=VIN,

nom IO=80% of IO, max. Figure 18. Typical Start-Up Output Voltage Rise

Characteristic.

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

LINEAGE POWER 9

Characteristic Curves (continued)

The following figures provide typical characteristics for the SW003A5F91 (3.3V, 3.5A) at 25ºC. The figures are

identical for either positive or negative Remote On/Off logic.

00.511.522.533.

= 3 6 V

= 54 V

= 75V

EFFICIENCY (%)

OUTPUT CURRENT, Io (A)

On/Off VOLTAGE, OUTPUT VOLTAGE

VON/OFF(V) (2V/div) VO (V) (1V/div)

TIME, t (1.0ms/div)

Figure 19. Converter Efficiency Vs Load. Figure 22. Typical Start-Up Using Remote On/Off,

negative logic version shown.

0 102030405060708090100110

3.0m/s (600ft/min)

2.0m/s (400ft/min)

1.0m/s (200ft/min)

Natural Convection

OUTPUT CURRENT, Io (A)

AMBIENT TEMPERATURE, TA OC

OUTPUT VOLTAGE, OUTPUTCURRENT

VO (V) (50mV/div), IO (A) (0.5A/div)

TIME, t (1.0ms/div)

Figure 20. Derating Output Current versus Local

Ambien t Temperature and Airflow. Figure 23. Transient Response to Dynamic Load

Change from 50% to 75% to 50% of full load.

OUTPUT VOLTAGE,

VO (V) (20mV/div)

TIME, t (2μs/div)

OUTPUT VOLTAGE

VO (V) (1V/div)

TIME, t (100μs/div)

Figure 21. Typical Output Ripple and Noise, VIN=VIN,

nom IO=80% of IO, max. Figure 24. Typical Start-Up Output Voltage Rise

Characteristic.

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

LINEAGE POWER 10

Characteristic Curves (continued)

The following figures provide typical characteristics for the SC001A2B91 (12.0V, 1.2A) at 25ºC. The figures are

identical for either positive or negative Remote On/Off logic.

0.0 0.2 0.4 0.6 0.8 1.0 1.2

= 18 V

= 2 7V

= 3 6 V

EFFICIENCY (%)

OUTPUT CURRENT, Io (A)

On/Off VOLTAGE, OUTPUT VOLTAGE

VON/OFF(V) (2V/div) VO (V) (5V/div)

TIME, t (5ms/div)

Figure 25. Converter Efficiency Vs Load. Figure 28. Typical Start-Up Using Remote On/Off,

negative logic version shown.

0.0

0.2

0.4

0.6

0.8

1. 0

1. 2

1. 4

0 102030405060708090100110

3.0 m/s (600 ft./min.)

2.0 m/s (400 ft./min.)

1.0 m/s (200 ft./min.)

Natural Convection

OUTPUT CURRENT, Io (A)

AMBIENT TEMPERATURE, TA OC

OUTPUT VOLTAGE, OUTPUTCURRENT

VO (V) (50mV/div), IO (A) (0.25A/div)

TIME, t (1.0ms/div)

Figure 26. Derating Output Current versus Local

Ambien t Temperature and Airflow. Figure 29. Transient Response to Dynamic Load

Change from 50% to 75% to 50% of full load.

OUTPUT VOLTAGE,

VO (V) (50mV/div)

TIME, t (1μs/div)

OUTPUT VOLTAGE

VO (V) (2V/div)

TIME, t (100μs/div)

Figure 27. Typical Output Ripple and Noise, VIN=VIN,

nom IO=80% of IO, max. Figure 30. Typical Start-Up Output Voltage Rise

Characteristic.

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

LINEAGE POWER 11

Characteristic Curves (continued)

The following figures provide typical characteristics for the SC003A0A91 (5.0V, 3A) at 25ºC. The figures are identical

for either positive or negative Remote On/Off logic.

0 0 .5 1 1.5 2 2 .5 3

= 18 V

= 2 7V

= 3 6 V

EFFICIENCY (%)

OUTPUT CURRENT, Io (A)

On/Off VOLTAGE, OUTPUT VOLTAGE

VON/OFF(V) (2V/div) VO (V) (2V/div)

TIME, t (5ms/div)

Figure 31. Converter Efficiency Vs Load. Figure 34. Typical Start-Up Using Remote On/Off,

negative logic version shown.

0.0

0.5

1. 0

1. 5

2.0

2.5

3.0

3.5

0 102030405060708090100110

3.0 m/s (600 ft./min.)

2.0 m/s (400 ft./min.)

1.0 m/s (200 ft./min.)

Natural Convection

OUTPUT CURRENT, Io (A)

AMBIENT TEMPERATURE, TA OC

OUTPUT VOLTAGE, OUTPUTCURRENT

VO (V) (50mV/div), IO (A) (0. 5A/div)

TIME, t (1.0ms/div)

Figure 32. Derating Output Current versus Local

Ambien t Temperature and Airflow. Figure 35. Transient Response to Dynamic Load

Change from 50% to 75% to 50% of full load.

OUTPUT VOLTAGE,

VO (V) (20mV/div)

TIME, t (1μs/div)

OUTPUT VOLTAGE

VO (V) (1V/div)

TIME, t (100μs/div)

Figure 33. Typical Output Ripple and Noise, VIN=VIN,

nom IO=80% of IO, max. Figure 36. Typical Start-Up Output Voltage Rise

Characteristic.

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

LINEAGE POWER 12

Characteristic Curves (continued)

The following figures provide typical characteristics for the SC003A5F91 (3.3V, 3.5A) at 25ºC. The figures are

identical for either positive or negative Remote On/Off logic.

00.511.522.533.5

= 18 V

= 2 7V

= 3 6 V

EFFICIENCY (%)

OUTPUT CURRENT, Io (A)

On/Off VOLTAGE, OUTPUT VOLTAGE

VON/OFF(V) (2V/div) VO (V) (1V/div)

TIME, t (5ms/div)

Figure 37. Converter Efficiency Vs Load. Figure 40. Typical Start-Up Using Remote On/Off,

negative logic version shown.

0.0

0.5

1. 0

1. 5

2.0

2.5

3.0

3.5

4.0

0 102030405060708090100110

3.0 m/s (600 ft./min.)

2.0 m/s (400 ft./min.)

1.0 m/s (200 ft./min.)

Natural Convection

OUTPUT CURRENT, Io (A)

AMBIENT TEMPERATURE, TA OC

OUTPUT VOLTAGE, OUTPUTCURRENT

VO (V) (50mV/div), IO (A) (0. 5A/div)

TIME, t (1.0ms/div)

Figure 38. Derating Output Current versus Local

Ambien t Temperature and Airflow. Figure 41. Transient Response to Dynamic Load

Change from 50% to 75% to 50% of full load.

OUTPUT VOLTAGE,

VO (V) (20mV/div)

TIME, t (2μs/div)

OUTPUT VOLTAGE

VO (V) (1V/div)

TIME, t (50μs/div)

Figure 39. Typical Output Ripple and Noise, VIN=VIN,

nom IO=80% of IO, max. Figure 42. Typical Start-Up Output Voltage Rise

Characteristic.

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

LINEAGE POWER 13

Test Configurations

TO OSCILLOSCOPE CURRENT PROBE

LTEST

12μH

BATTERY

CS 220μF

E.S.R.<0.1Ω

@ 20°C 100kHz

33μF

Vin+

Vin-

NOTE: Measure input reflected ripple current with a simulated

source inductance (LTEST) of 12μH. Capacitor CS offsets

possible battery impedance. Measure current as shown

above.

Figure 43. Input Reflected Ripple Current Test Setup.

NOTE: All voltage measurements to be taken at the module

terminals, as shown above. If sockets are used then

Kelvin connections are required at the module terminals

to avoid measurement errors due to socket contact

resistance.

(+)

(

–

)

1uF

RESI STI V E

LO A D

SC O PE

COPPER STRIP

GROUND PLANE

10uF

Figure 44. Output Ripple and Noise Test Setup.

Vout+

Vout-

Vin+

Vin-

RLOAD

Rcontact Rdistribution

Rcontact

Rdistribution

VIN VO

NOTE: All voltage measurements to be taken at the module

terminals, as shown above. If sockets are used then

Kelvin connections are required at the module terminals

to avoid measurement errors due to socket contact

resistance.

Figure 45. Ou tput Vol ta ge and Effici en cy Tes t Setup.

η =

VO. IO

VIN. IIN

x 100 %

Efficiency

Design Considerations

Input Source Impedance

The power module should be connected to a low

ac-impedance source. Highly inductive source

impedance can affect the stability of the power module.

For the test configuration in Figure 43, a 33μF

electrolytic capacitor (ESR<0.7Ω at 100kHz), mounted

close to the power module helps ensure the stability of

the unit. Consult the factory for further application

guidelines.

Safety Considerations

For safety-agency approval of the system in which the

power module is used, the power module must be

installed in compliance with the spacing and separation

requirements of the end-use safety agency standard,

i.e., UL 60950-1-3, CSA C22.2 No. 60950-00, and VDE

0805 (IEC60950, 3rd Edition).

If the input source is non-SELV (ELV or a hazardous

voltage greater than 60 Vdc and less than or equal to

75Vdc), for the module’s output to be considered as

meeting the requirements for safety extra-low voltage

(SELV), all of the following must be true:

 The input source is to be provided with reinforced

insulation from any other hazardous voltages,

including the ac mains.

 One VIN pin and one VOUT pin are to be grounded,

or both the input and output pins are to be kept

floating.

 The input pins of the module are not operator

accessible.

 Another SELV reliability test is conducted on the

whole system (combination of supply source and

subject module), as required by the safety agencies,

to verify that under a single fault, hazardous

voltages do not appear at the module’s output.

Note: Do not ground either of the input pins of the

module without grounding one of the output pins.

This may allow a non-SELV voltage to appear

between the output pins and ground.

The power module has extra-low voltage (ELV) outputs

when all inputs are ELV.

For input voltages exceeding –60 Vdc but less than or

equal to –75 Vdc, these converters have been evaluated

to the applicable requirements of BASIC INSULATION

between secondary DC MAINS DISTRIBUTION input

(classified as TNV-2 in Europe) and unearthed SELV

outputs.

The input to these units is to be provided with a

maximum 3A time-delay fuse in the ungrounded lead.

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

LINEAGE POWER 14

Feature Description

Remote On/Off

Two remote on/off options are available. Positive logic

turns the module on during a logic high voltage on the

ON/OFF pin, and off during a logic low. Negative logic

remote On/Off, device code suffix “1”, turns the module

off during a logic high and on during a logic low.

To maintain compatibility with LW series power modules

the Remote On/Off pin is optional for the TH (through

hole) version. Standard TH modules have no On/Off pin

fitted. TH modules ordered with device code suffix “1”

are negative logic with the On/Off pin fitted. The On/Off

pin shall always be fitted on SMT versions.

ON/OFF

Vin+

Vin-

Ion/off

Von/off

Vout+

TRIM

Vout-

Figure 46. Circuit configuration for using Remote

On/Off Implementation.

To turn the power module on and off, the user must

supply a switch (open collector or equivalent) to control

the voltage (Von/off) between the ON/OFF terminal and

the VIN(-) terminal. Logic low is 0V ≤ Von/off ≤ 1.2V. The

maximum Ion/off during a logic low is 1mA, the switch

should be maintain a logic low level whilst sinking this

current.

During a logic high, the typical Von/off generated by the

module is 5.8V, and the maximum allowable leakage

current at Von/off = 5.8V is 50μA.

If not using the remote on/off feature:

For positive logic, leave the ON/OFF pin open.

For negative logic, short the ON/OFF pin to VIN(-).

Overcurrent Protection

To provide protection in a fault (output overload)

condition, the unit is equipped with internal

current-limiting circuitry and can endure current limiting

continuously. At the point of current-limit inception, the

unit enters hiccup mode. The unit operates normally

once the output current is brought back into its specified

range. The average output current during hiccup is 10%

IO, max.

Input Undervoltage Lockout

At input voltages below the input undervoltage lockout

limit, the module operation is disabled. The module will

only begin to operate once the input voltage is raised

above the undervoltage lockout turn-on threshold,

VUV/ON.

Once operating, the module will continue to operate until

the input voltage is taken below the undervoltage turn-off

threshold, VUV/OFF.

Over Voltage Protection

The output overvoltage protection consists of circuitry

that internally clamps the output voltage. If a more

accurate output overvoltage protection scheme is

required then this should be implemented externally via

use of the remote on/off pin.

Output Voltage Programming

Trimming allows the user to increase or decrease the

output voltage set point of the module. This is

accomplished by connecting an external resistor

between the TRIM pin and either the Vout+ pin or the

Vout- pin.

Note: Trim pin is optional on TH module version and

always present on SMT versions.

Trim Down – Decrease Output Voltage

By connecting an external resistor between the TRIM pin

and Vout+ pin (Radj-down), the output voltage set point

decreases (see figure 17). The following equation

determines the external resistor value to obtain an

output voltage change from Vo, nom to the desired Vo,

adj:

⎥

⎦

⎤

⎢

⎣

⎡−

−

×−

−H

VV GLV

Radjonomo

adjo

downadj )( )(

Note: Values for G, H, L and K are defined for each

module version in the following table 1.

Vout+

TRIM

Vout-

Radj-down

RLOAD

Vin+

ON/OFF

Vin-

Figure 17. Circuit Configuration to Decrease Output

Voltage.

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

LINEAGE POWER 15

Feature Descriptions (continued)

Trim Up – Increase Output Voltage

By connecting an external resistor between the TRIM pin

and Vout- pin (Radj-up), the output voltage set point

increases (see figure 48). The following equation

determines the external resistor value to obtain an

output voltage change from Vo, nom to the desired Vo,

adj:

⎥

⎦

⎤

⎢

⎣

⎡−

−−

−H

KLV LG

Radjo

upadj )( ,

Note: Values for G, H, L and K are defined for each

module version in the following table 1.

Vout+

TRIM

Vout-

Radj-up

RLOAD

Vin+

ON/OFF

Vin-

Figure 48. Circui t Configu ratio n to Incr eas e Output

Voltage.

Table 1. Trim Constants SW series

Module G H K L

Sx001A0C 10,000 5110 12.5 2.5

Sx001A2B 10,000 5110 9.5 2.5

Sx003A0A 5110 2050 2.5 2.5

Sx003A5F 5110 2050 0.8 2.5

The combination of the output voltage adjustment and

the output voltage initial tolerance must not exceed the

allowable trim range of 90% to 110% of the nominal

output voltage as measured between the Vout+ and

Vout- pins.

The SW/SC power modules have a fixed current-limit set

point. Therefore, as the output voltage is adjusted down,

the available output power is reduced.

Trim Examples

For SW003A0A, nominal 5.0V module. To trim module

down to 4.90V:

⎥

⎦

⎤

⎢

⎣

⎡−

−

×−

−2050

)9.40.5( 5110)5.29.4(

downadjR

−590,120downadjR

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

LINEAGE POWER 16

Thermal Considerations

The power modules operate in a variety of thermal

environments; however, sufficient cooling should be

provided to help ensure reliable operation.

Considerations include ambient temperature, airflow,

module power dissipation, and the need for increased

reliability. A reduction in the operating temperature of the

module will result in an increase in reliability. The

thermal data presented here is based on physical

measurements taken in a wind tunnel.

The thermal reference point, Tref used in the

specifications is shown in Figure 49. For reliable

operation this temperature should not exceed 120oC.

Tref

Figure 49. Tref Temperature Measurement Location.

Heat Transfer via Convection

Increased airflow over the module enhances the heat

transfer via convection. Derating figures showing the

maximum output current that can be delivered by each

module versus local ambient temperature (TA) for natural

convection and up to 3m/s (600 ft./min) are shown in the

respective Characteristics Curves section.

Please refer to the Application Note “Thermal

Characterization Process For Open-Frame Board-

Mounted Power Modules” for a detailed discussion of

thermal aspects including maximum device

temperatures.

EMC Con s i d er ati o n s

Figure 50 shows a suggested configuration to meet the

conducted emission limits of EN55022 Class B.

Notes: C1, C2, C3 and C6 are low impedance SMT

ceramics. C4 is a low impedance polymer film type

(Paktron CS4). Common Mode inductor is Pulse

Engineering type P0354 1.17mH.

VI(+)

SW003A0A

VI(-)

Vo +

Vo -

Pulse P0354

CMC 1.17mH

L1 10uH

C6 2 x 56nF

C5 N/F

4.7uF

Polymer

0.68uF

0.68uF 5V @ 3A

0.68uF

Figure 50. Suggested Configura tion for EN55022

Class B.

100K 500K 1M 5M 10M 30

Frequency(Hz)

Level (dBµV)

EN 55022 Class B Conducted Average dBuV

Figure 51. EMC signature using above filter,

SW003A0A.

For further information on designing for EMC

compliance, please refer to the FLTR100V10 data sheet

(FDS01-043EPS).

Layout Considerations

The SW/SC power module series are low profile in order

to be used in fine pitch system card architectures. As

such, component clearance between the bottom of the

power module and the mounting board is limited. Avoid

placing copper areas on the outer layer directly

underneath the power module. Also avoid placing via

interconnects underneath the power module.

For additional layout guide-lines, refer to the

FLTR100V10 data sheet.

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

LINEAGE POWER 17

Mechanical Outline for SW/SC Surface-Mount Module

Dimensions are in millimeters and (inches).

Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [Unless otherwise indicated]

x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.)

Top View

(1.1)

24.4

(0.96)

27.9

Side View

height

min stand-off

(0.100)

2.54

0.5

(.020)

max

compliance

MAX

(0.335)

8.50

Bottom View

Pi Function

1 Vin +

2 Vin -

3 ON/OFF

4 Vout +

5 TRIM

6 Vout -

10.16

(0.400)

20.32

(0.800)

(0.15)

7.62

(0.300)

12.70

(0.500)

(0.08)

20.323.8

2.0

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

LINEAGE POWER 18

Mechanical Outline for SW/SC Through Hole Module

Dimensions are in millimeters and (inches).

Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [Unless otherwise indicated]

x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.)

Top View

(1.1)

24.4

(0.96)

27.9

Side View

8.50

(0.335)

MAX

4.95

(0.195)

(0.185)

4.70

0.762

0.635

(0.030)

(0.025)

Ø 0.95

(0.0375)MAX

SECTION A-A

Bottom View

Pi Function

1 Vin +

2 Vin -

3 ON/OFF

(Optional)

4 Vout +

5 TRIM

(Optional)

6 Vout -

(0.400)

(0.08)

2.0 3.8 20.32

(0.800)

(0.15)

(0.300)

7.62

12.70

(0.500)

20.32

(0.800)

10.16

Recommended Pad Layout for Surface Mount and Through Hole Module

Dimensions are in millimeters and (inches).

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

LINEAGE POWER 19

Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [Unless otherwise indicated]

x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.)

Pin Function

1 Vin +

2 Vin -

3 ON/OFF

4 Vout +

5 TRIM

6 Vout -

10.16

(0.400)

20.32

(0.800)

(0.15)

7.62

(0.300)

12.70

(0.500)

(0.08) 20.323.8

2.0

IN 6 POSITIONS

MINIMUM PAD Ø 1.9mm

RECOMMENDED PAD Ø 2.8mm

Surface Mount Pad Layout – Component side view

Pin Function

1 Vin +

2 Vin -

3 ON/OFF

(Optional)

4 Vout +

5 TRIM

(Optional)

6 Vout -

10.16

(0.400)

20.32

(0.800)

(0.15)

7.62

(0.300)

12.70

(0.500)

(0.08) 20.323.8

2.0

IN 6 POSITIONS

PAD Ø 3.5mm

HOLE Ø1.2mm

Through-Hole Pad Layout – Component side view

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

LINEAGE POWER 20

Packaging Details

The SW001/003 series SMT versions are supplied in tape & reel as standard. Details of tape dimensions are shown

below. Modules are shipped in quantities of 150 modules per reel.

Tape Dimensions

Dimensions are in millimeters and (inches).

NOTE: CONFORMS TO EAI-481 REV. A STANDARD

EMBOSSED CARRIER

TOP COVER TAPE

4.00

(0.157)

(0.750)

PICK POINT (1.260)

FEED

DIRECTION

19.05

32.00

(1.450)

(1.590)

(1.732)

36.80

40.40

44.00

9.14

(0.360)

Reel Dimensions

Outside Diameter: 330.2 mm (13.00”)

Inside Diameter: 177.8 mm (7.00”)

Tape Width: 44.00 (1.732)

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

LINEAGE POWER 21

The SW/SC family of power modules is available for

either Through-Hole (TH) or Surface Mount (SMT)

soldering.

Through-Hole Soldering Information

The RoHS-compliant (Z codes) through-hole products

use the SAC (Sn/Ag/Cu) Pb-free solder and RoHS-

compliant components. They are designed to be

processed through single or dual wave soldering

machines. The pins have an RoHS-compliant finish

that is compatible with both Pb and Pb-free wave

soldering processes. A maximum preheat rate of

3°C/s is suggested. The wave preheat process

should be such that the temperature of the power

module board is kept below 210°C. For Pb solder,

the recommended pot temperature is 260°C, while the

Pb-free solder pot is 270°C max. Not all RoHS-

compliant through-hole products can be processed

with paste-through-hole Pb or Pb-free reflow process.

If additional information is needed, please consult with

your Lineage Power representative for more details.

Surface Mount Information

Pick and Place

The SW/SC-SR series of DC-to-DC power converters

use an open-frame construction and are designed for

surface mount assembly within a fully automated

manufacturing process.

The SW/SC-SR series modules are designed to use

the main magnetic component surface to allow for

pick and place.

12.70

10.7

Ø6.5 NOZZLE.

Note: All dimensions in mm.

Figure 52. Pick and Plac e Location.

Z Plan e Height

The ‘Z’ plane height of the pick and place location is

7.50mm nominal with an RSS tolerance of +/-0.25

mm.

Nozzle Recommendations

The module weight has been kept to a minimum by

using open frame construction. Even so, they have a

relatively large mass when compared with

conventional SMT components. Variables such as

nozzle size, tip style, vacuum pressure and placement

speed should be considered to optimize this process.

The minimum recommended nozzle diameter for

reliable operation is 5mm. The maximum nozzle outer

diameter, which will safely fit within the allowable

component spacing, is 6.5mm.

Oblong or oval nozzles up to 11 x 6 mm may also be

used within the space available.

For further information please contact your local

Lineage Power Technical Sales Representative.

Reflow Soldering Information

These power modules are large mass, low thermal

resistance devices and typically heat up slower

than other SMT components. It is recommended

that the customer review data sheets in order to

customize the solder reflow profile for each

application board assembly.

The following instructions must be observed when

SMT soldering these units. Failure to observe

these instructions may result in the failure of or

cause damage to the modules, and can adversely

affect long-term reliability.

The surface mountable modules in the SW/SC

family use our SMT technology called “Column Pin”

(CP) connectors. Figure 53 shows the CP

connector before and after reflow soldering onto the

end-board assembly.

Power Module Board

Insulator

Solder Ball

End assembly PCB

Figure 53. Column Pin Connector Before and

After R e fl ow Solderin g .

The CP is constructed from a solid copper pin with an

integral solder ball attached, which is composed of

tin/lead (Sn63/Pb37) solder for non-Z codes, or

Sn/Ag3.8/Cu0.7 (SAC) solder for –Z codes. The CP

connector design is able to compensate for large

amounts of co-planarity and still ensure a reliable

SMT solder joint. Typically, the eutectic solder melts

at 183oC (Sn/Pb solder) or 217-218 oC (SAC solder),

wets the land, and subsequently wicks the device

connection. Sufficient time must be allowed to fuse

the plating on the connection to ensure a reliable

solder joint.

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

LINEAGE POWER 22

Surface Mount Information (continued)

There are several types of SMT reflow technologies

currently used in the industry. These surface

mount power modules can be reliably soldered

using natural forced convection, IR (radiant

infrared), or a combination of convection/IR. The

recommended linear reflow profile using Sn/Pb

solder is shown in Figure 54 and 55. For reliable

soldering the solder reflow profile should be

established by accurately measuring the modules

CP connector temperatures.

REFLOW TEMP (°C)

10 0

15 0

200

250

300

Preheat zone

max 4

-1

Soak zone

30-240s

Heat zone

max 4

-1

Peak Temp 235

Co o ling

zo ne

1- 4

-1

lim

above

205

REFLOW TIME (S)

Figure 54. Recommended Reflow Profile for Sn/Pb

solder.

Figure 55. Time Limit, Tlim, Curv e Above 205oC

Reflow .

Lead Free Soldering

The –Z version SMT modules of the SW/SC series

are lead-free (Pb-free) and RoHS compliant and are

compatible in a Pb-free soldering process. Failure to

observe the instructions below may result in the

failure of or cause damage to the modules and can

adversely affect long-term reliability.

Pb-free Reflow Profile

Power Systems will comply with J-STD-020 Rev. C

(Moisture/Reflow Sensitivity Classification for

Nonhermetic Solid State Surface Mount Devices) for

both Pb-free solder profiles and MSL classification

procedures. This standard provides a recommended

forced-air-convection reflow profile based on the

volume and thickness of the package (table 4-2). The

suggested Pb-free solder paste is Sn/Ag/Cu (SAC).

The recommended linear reflow profile using

Sn/Ag/Cu solder is shown in Figure. 56.

Pe r J-STD-020 Re v. C

100

150

200

250

300

Reflow Time (Seconds)

Reflow Temp (°C)

Hea ting Zone

1°C/Second

Pe ak Temp 260°C

* Min. Time Above 235°C

15 Seco nds

*Time Above 217°C

60 Sec o nds

Cooling

Zone

Figure 56. Recommended linear reflow profile

using Sn/Ag/Cu solder.

MSL Rating

The SW/SC series SMT modules have a MSL rating

of 1.

Storage and Handling

The recommended storage environment and handling

procedures for moisture-sensitive surface mount

packages is detailed in J-STD-033 Rev. A (Handling,

Packing, Shipping and Use of Moisture/Reflow

Sensitive Surface Mount Devices). Moisture barrier

bags (MBB) with desiccant are required for MSL

ratings of 2 or greater. These sealed packages

should not be broken until time of use. Once the

original package is broken, the floor life of the product

at conditions of ≤ 30°C and 60% relative humidity

varies according to the MSL rating (see J-STD-033A).

The shelf life for dry packed SMT packages will be a

minimum of 12 months from the bag seal date, when

stored at the following conditions: < 40° C, < 90%

relative humidity.

Post Solder Cleaning and Drying

Considerations

Post solder cleaning is usually the final circuit-board

assembly process prior to electrical board testing. The

result of inadequate cleaning and drying can affect

both the reliability of a power module and the

testability of the finished circuit-board assembly. For

guidance on appropriate soldering, cleaning and

drying procedures, refer to Lineage Power Board

Mounted Pow er Module s : Sold ering a nd Clean in g

Application Note (AP01-056EPS).

MAX TEMP SOLDER (°C)

200

205

210

215

220

225

230

235

240

0 10 203040 5060

TIME LIMIT (S)

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

LINEAGE POWER 23

Ordering Information

Please contact your Lineage Power Sales Representative for pricing, availability and optional features.

Table 2. Device Codes

Product codes Input

Voltage Output

Current Remote On/Off

Logic Connector

Type Comcodes

SW001A0C91Z 48 Vdc 15.0V 1.0A Negative Through-Hole CC109107331

SW001A2B 48 Vdc 12.0V 1.2A Not present Through-Hole 108989637

SW001A2B9 48 Vdc 12.0V 1.2A Not present Through-Hole 108984576

SW001A2B91 48 Vdc 12.0V 1.2A Negative Through-Hole 108981788

SW001A2B91-33Z 48 Vdc 12.0V 1.2A Negative Through-Hole CC109104568

SW001A2B9Z 48 Vdc 12.0V 1.2A Not present Through-Hole CC109107348

SW001A2B91Z 48 Vdc 12.0V 1.2A Negative Through-Hole CC109107356

SW001A2B94 48 Vdc 12.0V 1.2A Positive Through-Hole 108987314

SW001A2B961-33BZ 48 Vdc 12.0V 1.2A Negative Through-Hole CC109120623

SW001A2B91-SR 48 Vdc 12.0V 1.2A Negative SMT (tape & reel) 108988787

SW001A2B91-SRZ 48 Vdc 12.0V 1.2A Negative SMT (tape & reel) 108995718

SW003A0A 48 Vdc 5.0V 3.0A Not present Through-Hole 108985276

SW003A0A1 48 Vdc 5.0V 3.0A Negative Through-Hole 108985284

SW003A0A9 48 Vdc 5.0V 3.0A Not present Through-Hole 108984790

SW003A0A91 48 Vdc 5.0V 3.0A Negative Through-Hole 108981549

SW003A0A91Z 48 Vdc 5.0V 3.0A Negative Through-Hole CC109107380

SW003A0A94 48 Vdc 5.0V 3.0A Positive Through-Hole 108986928

SW003A0A94Z 48 Vdc 5.0V 3.0A Positive Through-Hole CC109107397

SW003A0A961 48 Vdc 5.0V 3.0A Negative Through-Hole 108989901

SW003A0A9Z 48 Vdc 5.0V 3.0A Not present Through-Hole CC109107372

SW003A0AZ 48 Vdc 5.0V 3.0A Not present Through-Hole CC109107364

SW003A0A91-SR 48 Vdc 5.0V 3.0A Negative SMT (tape & reel) 108984550

SW003A0A91-SRZ 48 Vdc 5.0V 3.0A Negative SMT (tape & reel) 109100468

SW003A0A94-SRZ 48 Vdc 5.0V 3.0A Positive SMT (tape & reel) 109100476

SW003A5F 48 Vdc 3.3V 3.5A Not present Through-Hole 108988275

SW003A5F91 48 Vdc 3.3V 3.5A Negative Through-Hole 108981556

SW003A5F91Z 48 Vdc 3.3V 3.5A Negative Through-Hole CC109107406

SW003A5F94 48 Vdc 3.3V 3.5A Positive Through-Hole 108986902

SW003A5F94Z 48 Vdc 3.3V 3.5A Positive Through-Hole CC109107414

SW003A5F961 48 Vdc 3.3V 3.5A Negative Through-Hole 108989620

SW003A5F91-SR 48 Vdc 3.3V 3.5A Negative SMT (tape & reel) 108982059

SW003A5F91-SRZ 48 Vdc 3.3V 3.5A Negative SMT (tape & reel) 109100492

SW003A5F94-SR 48 Vdc 3.3V 3.5A Positive SMT (tape & reel) 108986910

SW003A5F94-SRZ 48 Vdc 3.3V 3.5A Positive SMT (tape & reel) CC109114526

SC001A2B91 24 Vdc 12.0V 1.2A Negative Through-Hole 108988267

SC001A2B91Z 24 Vdc 12.0V 1.2A Negative Through-Hole CC109107298

SC001A2B91-SR 24 Vdc 12.0V 1.2A Negative SMT (tape & reel) 108996468

SC001A2B91-SRZ 24 Vdc 12.0V 1.2A Negative SMT (tape & reel) CC109121976

SC003A0A 24 Vdc 5.0V 3.0A Not present Through-Hole 108988291

SC003A0A91 24 Vdc 5.0V 3.0A Negative Through-Hole 108988283

SC003A0A91Z 24 Vdc 5.0V 3.0A Negative Through-Hole CC109107307

SC003A0A94 24 Vdc 5.0V 3.0A Positive Through-Hole 108989967

SC003A0A94Z 24 Vdc 5.0V 3.0A Positive Through-Hole CC109107315

SC003A0A91-SR 24 Vdc 5.0V 3.0A Negative SMT (tape & reel) 108988325

SC003A5F 24 Vdc 3.3V 3.5A Not present Through-Hole 108988300

SC003A5F91 24 Vdc 3.3V 3.5A Negative Through-Hole 108982034

SC003A5F91Z 24 Vdc 3.3V 3.5A Negative Through-Hole CC109107323

SC003A5F91-SR 24 Vdc 3.3V 3.5A Negative SMT (tape & reel) 108990644

SC003A5F91-SRZ 24 Vdc 3.3V 3.5A Negative SMT (tape & reel) 109100435

Data Sheet

October 5, 2009 SW/SC001/003 Series DC-DC Power Module:

18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current

Document No: DS03-086 ver. 1.91

PDF name: sw001-002-003_series.pdf

Table 3. Device Options

Option* Device Code Suffix**

Negative remote on/off logic (On/Off pin fitted)† 1

Positive remote on/off logic (On/Off pin fitted) † 4

Short Pins, 3.68 mm ± 0.25mm (0.145 in. ± 0.010 in.) 6

Output Voltage Adjustment (Trim pin fitted) † 9

Surface mount connections, SMT (Tape & Reel) -SR

RoHS Compliant -Z

* Please contact Lineage Power Sales Representative for availability of these options, samples, minimum order

quantity and lead times. Legacy device codes may contain a –B option suffix to indicate 100% factory Hi-Pot tested to

the isolation voltage specified in the Absolute Maximum Ratings table. The 100% Hi-Pot test is now applied to all

device codes, with or without the –B option suffix. Existing comcodes for devices with the –B suffix are still valid;

however, no new comcodes for devices containing the –B suffix will be created.

** When adding multiple options to the product code, add numerical suffix codes in the descending order.

† Either negative or positive logic (1 or 4), and output voltage adjustment (trim, 9) must be ordered on surface mount ,

SMT (-SR) device codes. Both the on/off pin and trim pin will be provided on all –SR device codes.

World Wide Headquarters

Lineage Power Corpor ation

601 Shiloh Road, Plano, TX 75074, USA

+1-800-526-7819

(Outside U.S.A.: +1-972-244-9428)

www.lineagepower.com

e-mail: techsupport1@lineagepower.com

Asia- Pacific Headquarters

Tel: +65 6593 7211

Europe, Middle-East and Afric a Headquarters

Tel: +49 898 780 672 80

India Headquarters

Tel: +91 80 28411633

Lineage Powe r reserves the right to make changes to the prod uct(s) or informat ion conta ined herein without not ice. No liability is assumed as a result of their use or

pplication. No rights under any patent accompany the sale of any such product(s) or information.

Lineage Power DC-DC products are prote cted unde r various patents. Information on these patents is available at www.lineagepower.com/patents.

2009 Linea

e Power Cor

oration

(

Plano

Texas

)

All Inte rnational Ri

hts Reserved.