LM2621 www.ti.com SNVS033C - MAY 2004 - REVISED MARCH 2005 LM2621 Low Input Voltage, Step-Up DC-DC Converter Check for Samples: LM2621 FEATURES DESCRIPTION * The LM2621 is a high efficiency, step-up DC-DC switching regulator for battery-powered and low input voltage systems. It accepts an input voltage between 1.2V and 14V and converts it into a regulated output voltage. The output voltage can be adjusted between 1.24V and 14V. It has an internal 0.17 N-Channel MOSFET power switch. Efficiencies up to 90% are achievable using the LM2621. 1 2 * * * * * * * * * Small VSSOP8 Package (Half the Footprint of Standard 8-Pin SOIC Package) 1.09 mm Package Height Up to 2 MHz Switching Frequency 1.2V to 14V Input Voltage 1.24V - 14V Adjustable Output Voltage Up to 1A Load Current 0.17 Internal MOSFET Up to 90% Regulator Efficiency 80 A Typical Operating Current <2.5A Ensured Supply Current In Shutdown APPLICATIONS * * * * * * * * * * PDAs, Cellular Phones 2-Cell and 3-Cell Battery-Operated Equipment PCMCIA Cards, Memory Cards Flash Memory Programming TFT/LCD Applications 3.3V to 5.0V Conversion GPS Devices Two-Way Pagers Palmtop Computers Hand-Held Instruments The high switching frequency (adjustable up to 2MHz) of the LM2621 allows for tiny surface mount inductors and capacitors. Because of the unique constant-dutycycle gated oscillator topology very high efficiencies are realized over a wide load range. The supply current is reduced to 80A because of the BiCMOS process technology. In the shutdown mode, the supply current is less than 2.5A. The LM2621 is available in a VSSOP-8 package. This package uses half the board area of a standard 8-pin SOIC and has a height of just 1.09 mm. Typical Application Circuit 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2004-2005, Texas Instruments Incorporated LM2621 SNVS033C - MAY 2004 - REVISED MARCH 2005 www.ti.com Connection Diagram Figure 1. VSSOP-8 (DGK) Package - Top View These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. ABSOLUTE MAXIMUM RATINGS (1) (2) -0.5 V to 14.5V SW Pin Voltage -0.5V to 10V BOOT, VDD, EN and FB Pins FREQ Pin 100A JA (3) 240C/W TJmax (3) 150C -65C to +150C Storage Temperature Range Lead Temp. (Soldering, 5 sec) Power Dissipation (TA=25C) 260C (3) 500mW ESD Rating (4) (1) (2) (3) (4) 2kV Absolute maximum ratings indicate limits beyond which damage to the device may occur. Electrical specifications do not apply when operating the device outside of its rated operating conditions. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. The maximum power dissipation must be derated at elevated temperatures and is dictated by Tjmax (maximum junction temperature), JA (junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is Pdmax = (Tjmax - TA)/ JA or the number given in the Absolute Maximum Ratings, whichever is lower. The human body model is a 100 pF capacitor discharged through a 1.5 k resistor into each pin. For Pin 8 (SW) the ESD rating is 1.5 kV. OPERATING CONDITIONS (1) VDD Pin 2.5V to 5V FB, EN Pins 0 to VDD BOOT Pin 0 to 10V -40C to +85C Ambient Temperature (TA) (1) 2 Absolute maximum ratings indicate limits beyond which damage to the device may occur. Electrical specifications do not apply when operating the device outside of its rated operating conditions. Submit Documentation Feedback Copyright (c) 2004-2005, Texas Instruments Incorporated Product Folder Links: LM2621 LM2621 www.ti.com SNVS033C - MAY 2004 - REVISED MARCH 2005 ELECTRICAL CHARACTERISTICS Limits in standard typeface are for TJ = 25C, and limits in boldface type apply over the full operating temperature range of -40C to +85C. Unless otherwise specified: VDD= VOUT= 3.3V. Condition Typ VIN_ST Symbol Minimum Start-Up Supply Voltage (1) Parameter ILOAD = 0mA 1.1 VIN_OP Minimum Operating Supply Voltage (once started) ILOAD = 0mA 0.65 VFB FB Pin Voltage VOUT_M Maximum Output Voltage 1.24 Min Max Units 1.2 V V 1.2028 1.2772 14 V V AX VHYST Hysteresis Voltage (2) Efficiency 30 VIN = 3.6V; VOUT = 5V; ILOAD = 500mA 87 VIN = 2.5V; VOUT = 3.3V; ILOAD = 200mA 87 70 45 mV % D Switch Duty Cycle IDD Operating Quiescent Current (3) FB Pin > 1.3V; EN Pin at VDD 80 % 80 60 110 A ISD Shutdown Quiescent Current (2) VDD, BOOT and SW Pins at 5.0V; EN Pin <200mV 0.01 2.5 A ICL Switch Peak Current Limit 2.85 A RDS_ON MOSFET Switch On Resistance 0.17 Enable Section VEN_LO EN Pin Voltage Low (4) VEN_HI EN Pin Voltage High (4) (1) (2) (3) (4) 0.15VDD 0.7VDD V V Output in regulation, VOUT = VOUT (NOMINAL) 5% This is the total current into pins VDD, BOOT, SW and FREQ. This is the current into the VDD pin. When the EN pin is below VEN_LO, the regulator is shut down; when it is above VEN_HI, the regulator is operating. PIN DESCRIPTION Pin Name Function 1 PGND Power Ground 2 EN Active-Low Shutdown Input 3 FREQ Frequency Adjust. An external resistor connected between this pin and Pin 6 (VDD) sets the switching frequency of the LM2621. 4 FB Output Voltage Feedback 5 SGND Signal Ground 6 VDD Power Supply for Internal Circuitry 7 BOOT Bootstrap Supply for the Gate Drive of Internal MOSFET Power Switch 8 SW Drain of the Internal MOSFET Power Switch Submit Documentation Feedback Copyright (c) 2004-2005, Texas Instruments Incorporated Product Folder Links: LM2621 3 LM2621 SNVS033C - MAY 2004 - REVISED MARCH 2005 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS Efficiency vs Load Current VOUT = 5.0V Efficiency vs Load Current VOUT = 3.3V Figure 2. Figure 3. VFB vs Temperature 4 IOP vs Temperature Figure 4. Figure 5. ISD vs Temperature ISD vs VDD Figure 6. Figure 7. Submit Documentation Feedback Copyright (c) 2004-2005, Texas Instruments Incorporated Product Folder Links: LM2621 LM2621 www.ti.com SNVS033C - MAY 2004 - REVISED MARCH 2005 TYPICAL PERFORMANCE CHARACTERISTICS (continued) IOP vs VDD VIN_ST vs Load Current VOUT = 3.3V Figure 8. Figure 9. Switching Frequency vs RFQ Peak Inductor Current vs Load Current Figure 10. Figure 11. Maximum Load Current vs Input Voltage Figure 12. Submit Documentation Feedback Copyright (c) 2004-2005, Texas Instruments Incorporated Product Folder Links: LM2621 5 LM2621 SNVS033C - MAY 2004 - REVISED MARCH 2005 www.ti.com DETAILED DESCRIPTION OPERATING PRINCIPLE The LM2621 is designed to provide step-up DC-DC voltage regulation in battery-powered and low-input voltage systems. It combines a step-up switching regulator, N-channel power MOSFET, built-in current limit, thermal limit, and voltage reference in a single 8-pin VSSOP package Figure 13. The switching DC-DC regulator boosts an input voltage between 1.2V and 14V to a regulated output voltage between 1.24V and 14V. The LM2621 starts from a low 1.1V input and remains operational down to 0.65V. This device is optimized for use in cellular phones and other applications requiring a small size, low profile, as well as low quiescent current for maximum battery life during stand-by and shutdown. A high-efficiency gatedoscillator topology offers an output of up to 1A. Additional features include a built-in peak switch current limit, and thermal protection circuitry. Figure 13. Functional Diagram GATED OSCILLATOR CONTROL SCHEME A unique gated oscillator control scheme enables the LM2621 to have an ultra-low quiescent current and provides a high efficiency over a wide load range. The switching frequency of the internal oscillator is programmable using an external resistor and can be set between 300 kHz and 2 MHz. This control scheme uses a hysteresis window to regulate the output voltage. When the output voltage is below the upper threshold of the window, the LM2621 switches continuously with a fixed duty cycle of 70% at the switching frequency selected by the user. During the first part of each switching cycle, the internal N-channel MOSFET switch is turned on. This causes the current to ramp up in the inductor and store energy. During the second part of each switching cycle, the MOSFET is turned off. The voltage across the inductor reverses and forces current through the diode to the output filter capacitor and the load. Thus when the LM2621 switches continuously, the output voltage starts to ramp up. When the output voltage hits the upper threshold of the window, the LM2621 stops switching completely. This causes the output voltage to droop because the energy stored in the output capacitor is depleted by the load. When the output voltage hits the lower threshold of the hysteresis window, the LM2621 starts switching continuously again causing the output voltage to ramp up towards the upper threshold. Figure 14 shows the switch voltage and output voltage waveforms. 6 Submit Documentation Feedback Copyright (c) 2004-2005, Texas Instruments Incorporated Product Folder Links: LM2621 LM2621 www.ti.com SNVS033C - MAY 2004 - REVISED MARCH 2005 Because of this type of control scheme, the quiescent current is inherently very low. At light loads the gated oscillator control scheme offers a much higher efficiency compared to the conventional PWM control scheme. Figure 14. Typical Step-Up Regulator Waveforms LOW VOLTAGE START-UP The LM2621 can start-up from input voltages as low as 1.1V. On start-up, the control circuitry switches the Nchannel MOSFET continuously at 70% duty cycle until the output voltage reaches 2.5V. After this output voltage is reached, the normal step-up regulator feedback and gated oscillator control scheme take over. Once the device is in regulation it can operate down to a 0.65V input, since the internal power for the IC can be bootstrapped from the output using the VDD pin. SHUTDOWN The LM2621 features a shutdown mode that reduces the quiescent current to less than a ensured 2.5A over temperature. This extends the life of the battery in battery powered applications. During shutdown, all feedback and control circuitry is turned off. The regulator's output voltage drops to one diode drop below the input voltage. Entry into the shutdown mode is controlled by the active-low logic input pin EN (Pin 2). When the logic input to this pin pulled below 0.15VDD, the device goes into shutdown mode. The logic input to this pin should be above 0.7VDD for the device to work in normal step-up mode. OUTPUT VOLTAGE RIPPLE FREQUENCY A major component of the output voltage ripple is due to the hysteresis used in the gated oscillator control scheme. The frequency of this voltage ripple is proportional to the load current. The frequency of this ripple does not necessitate the use of larger inductors and capacitors however, since the size of these components is determined by the switching frequency of the oscillator which can be set upto 2MHz using an external resistor. INTERNAL CURRENT LIMIT AND THERMAL PROTECTION An internal cycle-by-cycle current limit serves as a protection feature. This is set high enough (2.85A typical, approximately 4A maximum) so as not to come into effect during normal operating conditions. An internal thermal protection circuitry disables the MOSFET power switch when the junction temperature (TJ) exceeds about 160C. The switch is re-enabled when TJ drops below approximately 135C. Submit Documentation Feedback Copyright (c) 2004-2005, Texas Instruments Incorporated Product Folder Links: LM2621 7 LM2621 SNVS033C - MAY 2004 - REVISED MARCH 2005 www.ti.com Design Procedure SETTING THE OUTPUT VOLTAGE The output voltage of the step-up regulator can be set between 1.24V and 14V by connecting a feedback resistive divider made of RF1 and RF2. The resistor values are selected as follows: RF2 = RF1 /[(VOUT/ 1.24) -1] (1) A value of 150k is suggested for RF1. Then, RF2 can be selected using the above equation. A 39pF capacitor (CF1) connected across RF1 helps in feeding back most of the AC ripple at VOUT to the FB pin. This helps reduce the peak-to-peak output voltage ripple as well as improve the efficiency of the step-up regulator, because a set hysteresis of 30mV at the FB pin is used for the gated oscillator control scheme. BOOTSTRAPPING When the output voltage (VOUT) is between 2.5V and 5.0V a bootstrapped operation is suggested. This is achieved by connecting the VDD pin (Pin 6) to VOUT. However if the VOUT is outside this range, the VDD pin should be connected to a voltage source whose range is between 2.5V and 5V. This can be the input voltage (VIN), VOUT stepped down using a linear regulator, or a different voltage source available in the system. This is referred to as non-bootstrapped operation. The maximum acceptable voltage at the BOOT pin (Pin 7) is 10V. SETTING THE SWITCHING FREQUENCY The switching frequency of the oscillator is selected by choosing an external resistor (RFQ) connected between FREQ and VDD pins. See the graph titled " Switching Frequency vs RFQ" in the TYPICAL PERFORMANCE CHARACTERISTICS section of the datasheet for choosing the RFQ value to achieve the desired switching frequency. A high switching frequency allows the use of very small surface mount inductors and capacitors and results in a very small solution size. A switching frequency between 300kHz and 2MHz is recommended. INDUCTOR SELECTION The LM2621's high switching frequency enables the use of a small surface mount inductor. A 6.8H shielded inductor is suggested. The inductor should have a saturation current rating higher than the peak current it will experience during circuit operation (see graph titled " Peak Inductor Current vs. Load Current" in the TYPICAL PERFORMANCE CHARACTERISTICS section). Less than 100m ESR is suggested for high efficiency. Open-core inductors cause flux linkage with circuit components and interfere with the normal operation of the circuit. They should be avoided. For high efficiency, choose an inductor with a high frequency core material, such as ferrite, to reduce the core losses. To minimize radiated noise, use a toroid, pot core or shielded core inductor. The inductor should be connected to the SW pin as close to the IC as possible. See Table 1 for a list of the inductor manufacturers. OUTPUT DIODE SELECTION A Schottky diode should be used for the output diode. The forward current rating of the diode should be higher than the load current, and the reverse voltage rating must be higher than the output voltage. Do not use ordinary rectifier diodes, since slow switching speeds and long recovery times cause the efficiency and the load regulation to suffer. Table 1 shows a list of the diode manufacturers. INPUT AND OUTPUT FILTER CAPACITORS SELECTION Tantalum chip capacitors are recommended for the input and output filter capacitors. A 22F capacitor is suggested for the input filter capacitor. It should have a DC working voltage rating higher than the maximum input voltage. A 68F tantalum capacitor is suggested for the output capacitor. The DC working voltage rating should be greater than the output voltage. Very high ESR values (>3) should be avoided. Table 1 shows a list of the capacitor manufacturers. 8 Submit Documentation Feedback Copyright (c) 2004-2005, Texas Instruments Incorporated Product Folder Links: LM2621 LM2621 www.ti.com SNVS033C - MAY 2004 - REVISED MARCH 2005 Table 1. Suggested Manufacturers List Inductors Capacitors Diodes Coilcraft Tel: (800) 322-2645 Fax: (708) 639-1469 Sprague/ Vishay Tel: (207) 324-4140 Fax: (207) 324-7223 Motorola Tel: (800) 521-6274 Fax: (602) 244-6609 Coiltronics Tel: (407) 241-7876 Fax: (407) 241-9339 Kemet Tel: (864) 963-6300 Fax: (864) 963-6521 International Rectifier (IR) Tel: (310) 322-3331 Fax: (310) 322-3332 Pulse Engineering Tel: (619) 674-8100 Fax: (619) 674-8262 Nichicon Tel: (847) 843-7500 Fax: (847) 843-2798 General Semiconductor Tel: (516) 847-3222 Fax: (516) 847-3150 PC BOARD LAYOUT High switching frequencies and high peak currents make a proper layout of the PC board an important part of design. Poor design can cause excessive EMI and ground-bounce, both of which can cause malfunction and loss of regulation by corrupting voltage feedback signal and injecting noise into the control section. Power components - such as the inductor, input and output filter capacitors, and output diode - should be placed as close to the regulator IC as possible, and their traces should be kept short, direct and wide. The ground pins of the input and output filter capacitors and the PGND and SGND pins of LM2621 should be connected using short, direct and wide traces. The voltage feedback network (RF1, RF2, and CF1) should be kept very close to the FB pin. Noisy traces, such as from the SW pin, should be kept away from the FB and VDD pins. The traces that run between Vout and the FB pin of the IC should be kept away from the inductor flux. Always provide sufficient copper area to dissipate the heat due to power loss in the circuitry and prevent the thermal protection circuitry in the IC from shutting the IC down. Submit Documentation Feedback Copyright (c) 2004-2005, Texas Instruments Incorporated Product Folder Links: LM2621 9 LM2621 SNVS033C - MAY 2004 - REVISED MARCH 2005 www.ti.com Application examples Figure 15. EXAMPLE 1 - 5V/0.5A Step-Up Regulator U1 Texas Instruments LM2621MM C1 Vishay/Sprague 595D226X06R3B2T, Tantalum C2 Vishay/Sprague 595D686X0010C2T, Tantalum D1 Motorola MBRS140T3 L Coilcraft DT1608C-682 Figure 16. EXAMPLE 2 - 2mm Tall 5V/0.2A Step-Up Regulator for Low Profile Applications 10 U1 Texas Instruments LM2621MM C1 Vishay/Sprague 592D156X06R3B2T, Tantalum C2 Vishay/Sprague 592D336X06R3C2T, Tantalum D1 Motorola MBRS140T3 L Vishay/Dale ILS-3825-03 Submit Documentation Feedback Copyright (c) 2004-2005, Texas Instruments Incorporated Product Folder Links: LM2621 LM2621 www.ti.com SNVS033C - MAY 2004 - REVISED MARCH 2005 Figure 17. EXAMPLE 3 - 3.3V/0.5A SEPIC Regulator U1 Texas Instruments LM2621MM C1 Vishay/Sprague 595D226X06R3B2T, Tantalum C2 Vishay/Sprague 595D686X0010C2T, Tantalum D1 Motorola MBRS140T3 L1, L2 Coilcraft DT1608C-682 CS Vishay/Vitramon VJ1210Y105M , Ceramic Submit Documentation Feedback Copyright (c) 2004-2005, Texas Instruments Incorporated Product Folder Links: LM2621 11 PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2015 PACKAGING INFORMATION Orderable Device Status (1) LM2621MM/NOPB Package Type Package Pins Package Drawing Qty ACTIVE VSSOP DGK 8 LM2621MMX NRND VSSOP DGK 8 LM2621MMX/NOPB ACTIVE VSSOP DGK 8 Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 S06A TBD Call TI Call TI -40 to 85 S06A 3500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 S06A (4/5) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2015 continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 2-Sep-2015 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LM2621MM/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LM2621MMX/NOPB VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 2-Sep-2015 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM2621MM/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0 LM2621MMX/NOPB VSSOP DGK 8 3500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2015, Texas Instruments Incorporated