DataSheeT - enpirion(R) power solutions EN6338QI 3A PowerSoC Step-Down DC-DC Switching Converter with Integrated Inductor DESCRIPTION FEATURES The EN6338QI is a Power System on a Chip (PowerSoC) DC-DC converter. It integrates MOSFET switches, small-signal circuits, compensation, and the inductor in an advanced 3.75mm x 3.75mm x 1.9mm 19-pin aEASI package. * High Efficiency (Up to 96%) The EN6338QI is specifically designed to meet the precise voltage and fast transient requirements of present and future high-performance, low-power processor, DSP, FPGA, memory boards and system level applications in distributed power architecture. The device's advanced circuit techniques, ultra high switching frequency, and proprietary integrated inductor technology deliver high-quality, ultra compact, non-isolated DC-DC conversion. * 1.5% V OUT Accuracy (Line, Load, Temp) The Intel Enpirion power solution significantly helps in system design and productivity by offering greatly simplified board design, layout and manufacturing requirements. In addition, a reduction in the number of vendors required for the complete power solution helps to enable an overall system cost savings. All Enpirion products are RoHS compliant and leadfree manufacturing environment compatible. * Light Load Mode Operation (LLM) * Excellent Ripple and EMI Performance * Up to 3A Continuous Operating Current * 2.7V to 6.6V Input Voltage Range * 1.9MHz Switching Frequency * 45mm2 Optimized Total Solution Size * Programmable Soft-Start * Power OK Indicator * Thermal, Over-Current, Short Circuit and UnderVoltage Protection * RoHS Compliant, MSL Level 3, 260C Reflow APPLICATIONS * Point of Load Regulation for FPGAs, Distributed Power Architectures, Low-Power ASICs, MultiCore, Communication Processors and DSPs * Space Constrained Applications Needing High Power Density * 5V/3.3V Bus Architectures Needing High Efficiency 47nF Efficiency vs. Output Current PGTE 100 BTMP VOUT VIN 10 2x 10F 0805 EN6338QI PGND PGND 2x 22F 0805 80 RA CA AVIN EN 10nF SS 90 VOUT VFB VDDB 15nF EFFICIENCY (%) PVIN RB 70 60 50 VOUT = 3.3V 40 VOUT = 2.5V CONDITIONS VIN = 5V EN6338QI 30 20 47nF 10 AGND BGND VOUT = 1.8V VOUT = 1.0V VOUT = 0.75V 0 0 Figure 1: Simplified Applications Circuit 0.5 1 1.5 2 OUTPUT CURRENT (A) 2.5 3 Figure 2: Efficiency at V IN = 5V Page 1 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI ORDERING INFORMATION Part Number Package Markings T J Rating Package Description EN6338QI EN6338QI -40C to +125C 19-pin (3.75mm x 3.75mm x 1.9mm) aEASI EVB-EN6338QI EN6338QI aEASI Evaluation Board Packing and Marking Information: https://www.altera.com/support/quality-and-reliability/packing.html PIN FUNCTIONS 1 2 AVI N NF 3 4 AGND NF 17 P GND 5 6 SS V FB 7 8 RLLM NF 9 10 EN P OK 11 12 BGND S YNC 18 13 14 V DDB NF P VI N 19 V OUT 15 16 BTM P P GTE Figure 3: Pin Diagram (Top View) NOTE A: NF pins are non-functional and unconnected internally. Area under NF pin locations may be used for vias to route VFB, POK and SYNC signals. NF pins do not require landing pads. NOTE B: White `dot' on top left is pin 1 indicator on top of the device package. Page 2 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI PIN DESCRIPTIONS PIN NAME TYPE FUNCTION 1 AVIN Power Input power supply for the controller. Connect to input voltage at a quiet point. 2, 4, 8, 14 NF - NON FUNCTIONAL - These pins are not internally connected and do not require landing pads. Area below these pins may be used for vias to route VFB, POK and SYNC signals to other layers. 3 AGND Ground Analog Ground. This is the controller ground return. Connect to a quiet ground. 5 SS Analog Soft-Start node. The soft-start capacitor is connected between this pin and AGND. The value of this capacitor determines the startup time. 6 VFB Analog This is the external feedback input pin. A resistor divider connects from the output to AGND. The mid-point of the resistor divider is connected to VFB. A feed-forward capacitor (C A ) and resistor (R C ) are required parallel to the upper feedback resistor (R A ). The output voltage regulation is based on the VFB node voltage equal to 0.600V. 7 RLLM Analog Programmable LLM engage resistor to AGND allows for adjustment of load current at which Light-Load Mode engages. Can be left open for PWM only operation. 9 EN Analog Input Enable. Applying logic high enables the output and initiates a soft-start. Applying logic low disables the output. 10 POK Digital Power OK is an open drain transistor used for power system state indication. POK is logic high when VOUT is within -10% of VOUT nominal. 11 BGND Ground Ground for VDDB. Do not connect to external ground. 12 SYNC Analog Dual function pin providing LLM Enable and External Clock Synchronization (see Application Section). At static Logic HIGH, device will allow automatic engagement of light load mode. At static logic LOW, the device is forced into PWM only. A clocked input to this pin will synchronize the internal switching frequency to the external signal. If this pin is left floating, it will pull to a static logic high, enabling LLM. 13 VDDB Analog Internal regulated voltage used for the internal control circuitry. 15 BTMP Ground Bottom plate ground for PGTE. 16 PGTE Analog PMOS gate. Ground Input/Output power ground. Connect to the ground electrode of the input and output filter capacitors. See VOUT and PVIN pin descriptions for more details. 17 PGND Page 3 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI PIN NAME TYPE FUNCTION 18 PVIN Power Input power supply. Connect to input power supply. Decouple with input capacitor to PGND pin. 19 VOUT Power Regulated converter output. Connect to the load and place output filter capacitor(s) between these pins and PGND pins. ABSOLUTE MAXIMUM RATINGS CAUTION: Absolute Maximum ratings are stress ratings only. Functional operation beyond the recommended operating conditions is not implied. Stress beyond the absolute maximum ratings may impair device life. Exposure to absolute maximum rated conditions for extended periods may affect device reliability. Absolute Maximum Pin Ratings PARAMETER SYMBOL MIN MAX UNITS PVIN, AVIN, VOUT -0.3 7.0 V EN, POK, SYNC -0.3 V IN +0.3 V VFB, SS, RLLM, PGTE, VDDB -0.3 2.5 V MIN MAX UNITS +150 C +150 C +260 C MAX UNITS Absolute Maximum Thermal Ratings PARAMETER CONDITION Maximum Operating Junction Temperature Storage Temperature Range Reflow Peak Body Temperature -65 (10 Sec) MSL3 JEDEC J-STD-020A Absolute Maximum ESD Ratings PARAMETER CONDITION MIN HBM (Human Body Model) 2000 V CDM (Charged Device Model) 500 V RECOMMENDED OPERATING CONDITIONS PARAMETER SYMBOL MIN MAX V IN 2.7 6.6 Output Voltage Range V OUT 0.75 Output Current Range I OUT Input Voltage Range Operating Junction Temperature TJ -40 V IN - V DO UNITS V (1) V 3 A +125 C Page 4 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI THERMAL CHARACTERISTICS PARAMETER SYMBOL TYPICAL UNITS Thermal Shutdown T SD 160 C Thermal Shutdown Hysteresis T SDH 25 C Thermal Resistance: Junction to Ambient (0 LFM) (2) JA 30 C/W Thermal Resistance: Junction to Case (0 LFM) JC 3 C/W (1) V DO (dropout voltage) is defined as (I LOAD x Droput Resistance). Please refer to Electrical Characteristics Table. (2) Based on 2oz. external copper layers and proper thermal design in line with EIJ/JEDEC JESD51-7 standard for high thermal conductivity boards. Page 5 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI ELECTRICAL CHARACTERISTICS NOTE: V IN = PVIN = AVIN = 5V, Minimum and Maximum values are over operating ambient temperature range unless otherwise noted. Typical values are at T A = 25C. PARAMETER Operating Input Voltage SYMBOL V IN TEST CONDITIONS MIN PVIN = AVIN 2.7 TYP MAX UNITS 6.6 V Under Voltage LockOut - V IN Rising V UVLOR Voltage above which UVLO is not asserted 2 2.3 2.45 V Under Voltage LockOut - V IN Falling V UVLOF Voltage below which UVLO is asserted 1.7 2.1 2.3 V Under Voltage LockOut Hysteresis V UVLO_HYS Shut-Down Supply Current IS AVIN Quiescent Current I AVINQ No Load Quiescent Current I VINQ Feedback Pin Voltage (3) V FB Feedback Pin Voltage (Load, Temp.) V FB Feedback Pin Voltage (Line, Load, Temp.) 200 EN = 0V LLM/SYNC = High V OUT = 0.75V PVIN and AVIN I LOAD = 0, T A =25C 0A I LOAD 3A -40C T J 125C 40 60 A 650 900 A 40 V OUT = 1.2V V OUT = 0.75V mV mA 0.7425 0.75 0.7575 V 0.739 0.75 0.761 V 0.735 0.75 0.765 V 2.7V V IN 6.6V V FB 0A I LOAD 3A -40C T J 125C Feedback pin Input Leakage Current (4) V OUT Rise Time Range (4) Soft Start Capacitance Range (4) VFB pin input leakage current -10 10 nA t RISE Capacitor programmable 0.8 8 ms C SS_RANGE Recommended C SS range 10 100 nF 10 15 A I FB Soft-Start Charging Current I SS Drop-Out Resistance (4) R DO Input to output resistance 50 80 m Drop-Out Voltage (4) V DO I OUT = 3A 150 240 mV 3.5 Page 6 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS 3 A Continuous Output Current I OUT Over Current Trip Level I OCP V IN = 5V, V OUT = 1.2V 4 6.5 V DISABLE EN pin logic going low 1.2 1.34 1.48 V EN Threshold V EN EN pin logic going high 1.22 1.36 1.5 V EN Pin Input Current I EN V EN = 5V; EN pin has ~250k pull down 20 35 A Disable Threshold EN Pull-Down Resistance Switching Frequency R EN_DOWN F SW 0 V EN = 5V; 250 Not a passive resistance Free running clock frequency SYNC Input Threshold - Low V SYNC_LO SYNC Clock Logic Level SYNC Input Threshold - High (5) V SYNC_HI SYNC Clock Logic Level POK High Threshold POK _HI Percentage of V OUT nominal when POK is asserted high A 1.6 1.9 1.8 k 2.2 MHz 0.8 V 2.5 V 90 % POK Low Voltage V POKL 4mA sink into POK 0.4 V POK High Voltage V POKH 2.7V V IN 6.6V V IN V POK Pin Leakage Current (4) I POKH POK is high 1 A LLM Headroom (4) LLM Logic Low (LLM/SYNC PIN) V LLM_LO LLM Static Logic Level LLM Logic High (LLM/SYNC PIN) V LLM_HI LLM Static Logic Level LLM/SYNC Pin Current 800 Minimum VIN - VOUT mV 0.3 1.5 LLM/SYNC Pin is <2.5V V V <100 nA (3) The VFB pin is a sensitive node. Do not touch VFB while the device is in regulation. (4) Parameter not production tested but is guaranteed by design. (5) High logic for frequency synchronization with SYNC pin must be below 2.5V. Page 7 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI TYPICAL PERFORMANCE CURVES Efficiency vs. Output Current 100 90 90 80 80 70 70 EFFICIENCY (%) EFFICIENCY (%) Efficiency vs. Output Current 100 60 50 VOUT = 2.5V 40 CONDITIONS VIN = 3.3V EN6338QI 30 20 10 VOUT = 1.8V 60 50 VOUT = 3.3V 40 VOUT = 2.5V VOUT = 1.0V 20 VOUT = 0.75V 10 0 CONDITIONS VIN = 5V EN6338QI 30 0.5 1 1.5 2 OUTPUT CURRENT (A) 3 2.5 0 VOUT = 0.75V 90 90 80 80 70 70 EFFICIENCY (%) 100 60 VOUT = 2.5V 40 VOUT = 1.8V 30 VOUT = 1.0V 20 VOUT = 0.75V 10 0 0.01 CONDITIONS VIN = 3.3V SYNC = High RLLM = 75k 0.1 1 OUTPUT CURRENT (A) 2.5 3 LLM Efficiency vs. Output Current 100 50 2 1 1.5 OUTPUT CURRENT (A) 0.5 LLM Efficiency vs. Output Current EFFICIENCY (%) VOUT = 1.0V 0 0 60 50 VOUT = 3.3V 40 VOUT = 2.5V 30 VOUT = 1.8V 20 VOUT = 1.0V 10 VOUT = 0.75V 0 0.01 10 Output Voltage vs. Output Current CONDITIONS VIN = 5V SYNC = High RLLM = 75k 0.1 1 OUTPUT CURRENT (A) 10 Output Voltage vs. Output Current 1.220 1.015 VIN = 5.0V 1.010 VIN = 3.3V OUTPUT VOLTAGE (V) 1.020 OUTPUT VOLTAGE (V) VOUT = 1.8V 1.005 1.000 0.995 0.990 CONDITIONS VOUT = 1.0V 0.985 1.215 VIN = 5.0V 1.210 VIN = 3.3V 1.205 1.200 1.195 1.190 CONDITIONS VOUT = 1.2V 1.185 0.980 1.180 0 0.5 1 1.5 2 OUTPUT CURRENT (A) 2.5 3 0 0.5 1 1.5 2 OUTPUT CURRENT (A) 2.5 3 Page 8 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI TYPICAL PERFORMANCE CURVES (CONTINUED) Output Voltage vs. Output Current Output Voltage vs. Output Current 1.820 1.515 VIN = 5.0V 1.510 VIN = 3.3V OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 1.520 1.505 1.500 1.495 1.490 CONDITIONS VOUT = 1.5V 1.485 0.5 1 1.5 2 OUTPUT CURRENT (A) VIN = 5.0V 1.810 VIN = 3.3V 1.805 1.800 1.795 1.790 1.780 3 2.5 0 1 2 1.5 OUTPUT CURRENT (A) 2.5 3 3.320 2.515 VIN = 5.0V 2.510 VIN = 3.3V 3.315 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 0.5 Output Voltage vs. Output Current Output Voltage vs. Output Current 2.520 2.505 2.500 2.495 2.490 CONDITIONS VOUT = 2.5V 2.485 VIN = 5.0V 3.310 3.305 3.300 3.295 3.290 CONDITIONS VOUT = 3.3V 3.285 3.280 2.480 0 0.5 1 1.5 2 OUTPUT CURRENT (A) 2.5 0 3 Output Voltage vs. Input Voltage 0.5 1 1.5 2 OUTPUT CURRENT (A) 2.5 3 Output Voltage vs. Input Voltage 1.820 1.820 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) CONDITIONS VOUT = 1.8V 1.785 1.480 0 1.815 1.815 1.810 1.805 1.800 1.795 1.790 CONDITIONS Load = 0A 1.785 1.815 1.810 1.805 1.800 1.795 1.790 CONDITIONS Load = 1A 1.785 1.780 1.780 2.4 3 3.6 4.2 4.8 5.4 INPUT VOLTAGE (V) 6 6.6 2.4 3 3.6 4.2 4.8 5.4 INPUT VOLTAGE (V) 6 6.6 Page 9 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI TYPICAL PERFORMANCE CURVES (CONTINUED) Output Voltage vs. Input Voltage Output Voltage vs. Input Voltage 1.820 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 1.820 1.815 1.810 1.805 1.800 1.795 1.790 CONDITIONS CONDITIONS Load = A Load = 2A 1.785 1.815 1.810 1.805 1.800 1.795 1.790 CONDITIONS CONDITIONS Load = A Load = 3A 1.785 1.780 1.780 2.4 3 3.6 4.2 4.8 5.4 INPUT VOLTAGE (V) 6 6.6 2.4 GUARANTEED OUTPUT CURRENT (A) GUARANTEED OUTPUT CURRENT (A) 4.5 4 3.5 3 2.5 2 CONDITIONS VIN = 5.0V VOUT = 1.0V 1 0.5 0 -40 -15 10 35 6 6.6 60 5 4.5 4 3.5 3 2.5 2 1.5 CONDITIONS VIN = 5.0V VOUT = 3.3V 1 0.5 0 -40 85 -15 10 35 60 85 AMBIENT TEMPERATURE(C) AMBIENT TEMPERATURE(C) EMI Performance (Horizontal Scan) EMI Performance (Vertical Scan) 100.0 100.0 80.0 70.0 60.0 50.0 CISPR 22 Class B 3m 40.0 30.0 CONDITIONS VIN = 5.0V VOUT_NOM = 1.5V LOAD = 0.5 90.0 LEVEL (dBV/m) CONDITIONS VIN = 5.0V VOUT_NOM = 1.5V LOAD = 0.5 90.0 LEVEL (dBV/m) 3.6 4.2 4.8 5.4 INPUT VOLTAGE (V) No Thermal Derating No Thermal Derating 5 1.5 3 80.0 70.0 60.0 50.0 CISPR 22 Class B 3m 40.0 30.0 20.0 20.0 10.0 10.0 30 30 300 FREQUENCY (MHz) 300 FREQUENCY (MHz) Page 10 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI TYPICAL PERFORMANCE CHARACTERISTICS Output Ripple at 20MHz Bandwidth Output Ripple at 20MHz Bandwidth VOUT 1.0V (AC Coupled) CONDITIONS VIN = 3.3V, IOUT = 0A CIN = 2 x 10F (0805) COUT = 2 x 22 F (0805) VOUT 1.0V (AC Coupled) VOUT 1.8V (AC Coupled) VOUT 1.8V (AC Coupled) VOUT 2.5V (AC Coupled) VOUT 2.5V (AC Coupled) Output Ripple at 20MHz Bandwidth VOUT 1.0V (AC Coupled) CONDITIONS VIN = 5V, IOUT = 0A CIN = 2 x 10F (0805) COUT = 2 x 22 F (0805) Output Ripple at 20MHz Bandwidth VOUT 1.0V (AC Coupled) VOUT 1.8V (AC Coupled) VOUT 1.8V (AC Coupled) VOUT 3.3V (AC Coupled) VOUT 3.3V (AC Coupled) LLM Output Ripple at 100mA CONDITIONS VIN = 3.3V, IOUT = 3A CIN = 2 x 10F (0805) COUT = 2 x 22 F (0805) CONDITIONS VIN = 5V, IOUT = 3A CIN = 2 x 10F (0805) COUT = 2 x 22 F (0805) LLM Output Ripple at 100mA VOUT (AC Coupled) VOUT (AC Coupled) CONDITIONS VIN = 3.3V VOUT = 1V IOUT = 100mA CIN = 2 x 22F (0805) COUT = 2 x 47 F (0805) CONDITIONS VIN = 5V VOUT = 1V IOUT = 100mA CIN = 2 x 22F (0805) COUT = 2 x 47 F (0805) Page 11 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI TYPICAL PERFORMANCE CHARACTERISTICS (CONTINUED) Enable Power Up/Down Enable Power Up/Down ENABLE ENABLE VOUT VOUT POK LOAD POK CONDITIONS VIN = 5.5V, VOUT = 3.3V NO LOAD, Css = 15nF CIN = 2 x 22F (0805) COUT = 2 x 47 F (0805) LLM Load Transient from 0.01 to 3A LLM Load Transient from 0.01 to 3A VOUT (AC Coupled) LOAD VOUT (AC Coupled) CONDITIONS LLM = ENABLED VIN = 5V VOUT = 1V CIN = 2 x 22F (0805) COUT = 2 x 47 F (0805) LOAD CONDITIONS LLM = ENABLED VIN = 5V VOUT = 3V CIN = 2 x 22F (0805) COUT = 2 x 47 F (0805) PWM Load Transient from 0 to 3A PWM Load Transient from 0 to 3A VOUT (AC Coupled) VOUT (AC Coupled) LOAD CONDITIONS VIN = 5.5V, VOUT = 3.3V LOAD=1.1, Css = 15nF CIN = 2 x 22F (0805) COUT = 2 x 47 F (0805) LOAD CONDITIONS LLM = DISABLED VIN = 5V VOUT = 1V CIN = 2 x 22F (0805) COUT = 2 x 47 F (0805) LOAD CONDITIONS LLM = DISABLED VIN = 5V VOUT = 3V CIN = 2 x 22F (0805) COUT = 2 x 47 F (0805) Page 12 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI FUNCTIONAL BLOCK DIAGRAM RLLM BTMP PGTE PVIN UVLO Thermal Limit LDO VDDB BGND Current Limit P-Drive (-) Logic PWM Comp (+) VOUT N-Drive PGND PLL/Sawtooth Generator Compensation Network SYNC VFB (-) Error Amp (+) Power OK POK EN Soft-Start Internal Reference Internal Regulator AVIN AGND SS Figure 4: Functional Block Diagram FUNCTIONAL DESCRIPTION Synchronous DC-DC Step-Down PowerSoC The EN6338QI is a synchronous DC-DC buck regulator with integrated internal MOSFETs. The nominal input voltage range is 2.7V to 6.6V. The output voltage is programmed using an external resistor divider network. The control loop is voltage-mode with a type III compensation network. Much of the compensation circuitry is internal to the device, but a phase-lead capacitor and resistor are required to complete the compensation network. The type III voltage mode architecture with integrated compensation maximizes loop bandwidth without increasing complexity. This architecture is designed to maintain stability with excellent gain and phase margin and improve transient response. The enhanced voltage mode architecture also provides high noise immunity at light load and maintains excellent line and load regulation. Up to 3A of continuous output current Page 13 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI can be drawn from this converter. The 1.9MHz switching frequency allows the use of smaller case size input and output capacitors within a small footprint. The EN6338QI architecture includes the following features. Operational Features: * Automatic Light Load Mode (LLM) or Forced PWM mode selection * Soft-start circuit allowing controlled startup and shutdown * Power OK circuit indicating the output voltage is greater than 90% of programmed value Protection Features: * Over-current protection from short circuit or excessive load current * Thermal shutdown with hysteresis to prevent over temperature stress * Under-voltage lockout protection to prevent under-voltage operation Light Load Mode (LLM) Operation The EN6338QI uses a proprietary Light Load Mode (LLM) to provide high efficiency at low output currents. When the LLM/SYNC pin is asserted high, the device is in automatic LLM "Detection" mode. When the LLM/SYNC pin is low, the device is forced into PWM mode. In automatic LLM "Detection" mode, when a low output current condition is detected, the device will: (1) Step V OUT up by approximately 1.0% above the nominal operating output voltage setting, V NOM and as low as -0.5% below V NOM , and then (2) Shut down unnecessary circuitry, and then (3) Monitor V OUT When V OUT falls below V NOM , the device will repeat (1), (2), and (3). The voltage step-up, or pre-positioning, improves transient droop when a load transient causes a transition from LLM mode to PWM mode. If a load transient occurs, causing V OUT to fall below the threshold V MIN , the device will exit LLM operation and begin normal PWM operation. Figure 5 demonstrates V OUT behavior during the transition into and out of LLM operation. LLM Ripple VMA X PWM Ripple VOUT_NOM VMI N Load Step IOUT Time Figure 5: Light Load Mode Operation Illustration Page 14 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI Many multi-mode DCDC converters suffer from a condition that occurs when the load current increases only slowly so that there is no load transient driving V OUT below the V MIN threshold. In this condition, the device would never exit LLM operation. This could adversely affect efficiency and cause unwanted ripple. To prevent this from occurring, the EN6338QI periodically exits LLM mode into PWM mode and measures the load current. If the load current is above the LLM threshold current, the device will remain in PWM mode. If the load current is below the LLM threshold, the device will re-enter LLM operation. There may be a small overshoot or undershoot in V OUT when the device exits and re-enters LLM. The load current at which the device will enter LLM mode is a function of input and output voltage, and the RLLM pin resistor. For PWM only operation, the RLLM pin can be left open. There is a minimum headroom between input and output of 800mV in order to engage into LLM mode. LLM to PWM Current vs. RLLM LLM TO PWM CURRENT (A) 2.0 1.8 VIN = 5V, VOUT = 3.3V 1.6 VIN = 3.3V, VOUT = 2.5V 1.4 VIN = 5V, VOUT = 1V 1.2 VIN = 3.3V, VOUT = 1V 1.0 CONDITIONS TA = 25C L = 470nH 0.8 0.6 0.4 0.2 0.0 0 10 20 30 40 50 60 70 80 90 100 RLLM RESISTOR (k) Figure 6: LLM to PWM Transition Point with Various RLLM Values Enable Operation The enable (EN) pin provides a mean to startup or to shutdown the device. When the EN pin is asserted high, the device will undergo a normal soft-start where the output will rise monotonically into regulation. Asserting a logic low on this pin will deactivate the device by initiating a soft-shutdown. The soft-shutdown time is approximately 5 times faster than the soft-start time. The EN pin is internally pulled low by a non-passive ressitance of 250k. Soft-Start Operation The soft-start circuitry will reduce inrush current during startup as the regulator charges the output voltage up to nominal level gradually. The output rise time is controlled by the soft-start capacitor, which is placed between the SS pin and the AGND pin. When the part is enabled, the soft-start (SS) current generator charges the SS capacitor in a linear manner. Once the voltage on the SS capacitor reaches 0.75V, the controller selects the intenral bandgap voltage as the reference. The voltage across the SS capacitor will continue ramping up until it reaches around 1.36V. The rise time is defined as the time needed by the output voltage to go from zero to the programmed value. The rise time (t RISE ) is given by the following equation: Page 15 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI t RISE [ms] = C ss [nF] x 0.08 With a 15nF soft-start capacitance on the SS pin, the soft-start rise time will be set to 1.2ms. The recommended range for the value of the SS capacitor is between 10nF and 100nF. Note that excessive bulk capacitance on the output can cause an over current event on startup if the soft-start time is too low. Refer to the Compensation and Transient Response section for details on proper bulk capacitance usage. POK Operation The Power OK (POK) is an open drain signal to indicate if the output voltage is within the specified range. POK is asserted high when the rising output voltage exceeds 90% of the programmed output voltage. An external resistor (10k) should be connected to the intput in order to pull POK high. If the nominal output voltage falls below 90%, the POK signal will be asserted low by an internal 4mA pull-down transistor. Over-Current Protection (OCP) The current limit function is achieved by sensing the peak current flowing through the topside power PFET. When the sensed current exceeds the over current trip point (see Electrical Characteristics Table), both power FETs are turned off for the remainder of the switching cycle. If the over-current condition is removed, the overcurrent protection circuit will enable normal PWM operation. If the over-current condition persists, the soft start capacitor will gradually discharge causing the output voltage to fall. When the OCP fault is removed, the output voltage will ramp back up to the desired voltage. This cycle can continue indefinitely as long as the over current condition persists. The OCP circuit will disable operation and protect the device from excessive current during operation without compromising the full load capability of the device. Thermal Protection The thermal shutdown circuit disables the device operation (switching stops) when the junction temperature exceeds 160C. When the junction temperature drops by approximately 25C, the converter will re-start with a normal soft-start. By preventing operation at excessive temperatures, the thermal shutdown circuit will protect the device from overstress. Input Under-Voltage Lock-Out (UVLO) When the device input voltage falls below UVLO, switching is disabled to prevent operation at insufficient voltage levels. During startup, the UVLO circuit ensures that the converter will not start switching until the input voltage is above the specified minimum voltage. Hysteresis and input de-glitch circuits are incorporated in order to ensure high noise immunity and prevent a false trigger in the UVLO voltage region. Page 16 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI APPLICATION INFORMATION Output Voltage Setting The EN6338QI output voltage is programmed using a simple resistor divider network (R A and R B ). Figure 7 shows the resistor divider configuration. EN6338QI VOUT VOUT COUT (47F - 400F) PGND RA 200k CA (15pF - 68pF) VFB = 0.75V VFB RB = 0.75V x RA VOUT - 0.75V AGND Figure 7: V OUT Resistor Divider & Compensation Capacitor The recommended R A resistor value is 200k and the feedback voltage is typically 0.75V. Depending on the output voltage (V OUT ), the R B resistor value may be calculated as shown in Figure 7. Since the accuracy of the output voltage setting is dependent upon the feedback voltage and the external ressitors, 1% or better resistors are recommended. The external compensation capacitor (C A ) is also required in parallel with R A . Depending on input and output voltage, the recommended external compensation values are shown in Table 1. Table 1: External Compensation Recommendations V IN 2.7V - 6.6V V OUT RB CA 0.75V OPEN 27pF 0.9V 1M 27pF 1.0V 604k 22pF 1.2V 332k 22pF 1.5V 200k 18pF 1.8V 143k 18pF 2.5V 84.5k 15pF 3.3V 59k RA C OUT (0805) 200k 2 x 22F 15pF Page 17 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI Compensation and Transient Response The EN6338QI uses an enhanced type III voltage mode control architecture. Most of the compensation is internal, which simplifies the design. In some applications, improved transient performance may be desired with additional output capacitors (C OUT ). In such an instance, the phase-lead capacitor (C A ) can be adjusted depending on the total output capacitance. Using Table 1 as the reference for C A , if C OUT is increased, then the C A should also be increased. The relationship is linearly shown below: C OUT +100F C A +10pF As C OUT increases and the C A value is adjusted, the device bandwidth will reach its optimization level (at around 1/10th of the switching frequency). As shown in Table 1, the recommended C A value is lower for the 5V input than 3.3V input. This is to ensure that the loop bandwidth is not over extended due to the increased gain at the higher input voltage range. The C A value may be extrapolated for other input voltages. The limitation for adjusting the compensation is based on diminished return. Further adjustments by increasing C OUT and increasing C A may not yield better transient response or in some situations cause lower gain and phase margin. Over compensating with excessive output capacitance may also cause the device to trigger current limit on startup due to the energy required to charge the output up to regulation level. Due to such limitations, the recommended maximum output capacitance (C OUT_MAX ) is 400F and the recommended maximum phase-lead capacitance (C A_MAX ) is 68pF. Note that lower output voltages can accommodate a higher Ca value. Input Capacitor Selection The input of synchronous buck regulators can be very noisy and should be decoupled properly in order to ensure stable operation. In addition, input parasitic line inductance can attribute to higher input voltage ripple. The EN6338QI requires a minimum of 2 x 10F 0805 or 1 x 22F 1206 size with sufficient voltage rating. As the distance of the input power source to the input of the EN6338QI is increased, it is recommended to increase input capacitance in order to mitigate the line inductance from the source. Low-ESR ceramic capacitors should be used. The dielectric must be X5R or X7R rated and the size must be at least 0805 (EIA) due to derating. Y5V or equivalent dielectric formulations must not be used as these lose too much capacitance with frequency, temperature and bias voltage. In some applications, lower value capacitors are needed in parallel with the larger capacitors in order to provide high frequency decoupling. Larger electrolytic or tantalum bulk capacitors may be used in conjunction to increase total input capacitance but should not be used solely as a replacement for the ceramic capacitors. Table 3: Recommended Minimum Input Capacitors DESCRIPTION 10F 20%, 10V X5R, 0805 MFG Taiyo Yuden Murata TDK 22F 20%, 10V Taiyo Yuden X5R, 1206 Murata P/N LMK212BJ106KG-T GRM21BR61A106KE19L C2012X5R1A106M125AB LMK316BJ226ML-T GRM31CR61A226ME19L Page 18 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI Output Capacitor Selection The output ripple of a synchronous buck converter can be attributed to its inductance, switching frequency and output decoupling. The EN6338QI requires a minimum of 2 x 22F 0805 output capacitors or 1 x 47F 1206 size. Low ESR ceramic capacitors should be used. The dielectric must be X5R or X7R rated and the size must be at least 0805 (EIA) due to derating. Y5V or equivalent dielectric formulations must not be used as these lose too much capacitance with frequency, temperature and bias voltage. Table 4: Recommended Output Capacitors DESCRIPTION 22F 20%, 10V X5R, 0805 47F 20%, 10V X5R, 1206 MFG P/N Taiyo Yuden LMK212BBJ226MG-T Murata GRM21BR61A226ME51 TDK C2012X5R1A226M125AB Taiyo Yuden JMK316BJ476ML-T Murata GRM31CR60J476ME19L TDK C3216X5R1A476M160AB Output ripple voltage is determined by the aggregate output capacitor impedance. Output impedance, denoted as Z, is comprised of effective series resistance (ESR) and effective series inductance (ESL): Z = ESR + ESL The resonant frequency of a ceramic capacitor is inversely proportional to the capacitance. Lower capacitance corresponds to higher resonant frequency. When two capacitors are placed in parallel, the benefit of both are combined. It is beneficial to decouple the output with capacitors of various capacitance and size. Placing them all in parallel reduces the impedance and will hence result in lower output ripple. 1 Z Total = 1 1 1 + + ... + Z1 Z 2 Zn Page 19 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI THERMAL CONSIDERATIONS Thermal considerations are important elements of power supply design. Whenever there are power losses in a system, the heat that is generated by the power dissipation needs to be taken into account. The Intel Enpirion PowerSoC technology helps alleviate some of those concerns. The EN6338QI DC-DC converter is packaged in a 3.75mm x 3.75mm x 1.9mm 19-pin aEASI package. The aEASI package is constructed with copper lead frames that have exposed thermal pads. The exposed thermal pad on the package should be soldered directly on to a copper ground pad on the printed circuit board (PCB) to act as a heat sink. The recommended maximum junction temperature for continuous operation is 125C. Continuous operation above 125C may reduce long-term reliability. The device has a thermal overload protection circuit designed to turn off the device at an approximate junction temperature value of 160C. The following example and calculations illustrate the thermal performance of the EN6338QI with the following parameters: V IN = 5V V OUT = 3.3V I OUT = 3A First, calculate the output power. P OUT = V OUT x I OUT = 3.3V x 3A = 9.9W Next, determine the input power based on the efficiency () shown in Figure 8. LLM Efficiency vs. Output Current 100 90 EFFICIENCY (%) 80 LLM 70 PWM 60 50 40 30 CONDITIONS VIN = 5V 20 VOUT = 3.3V LLM VOUT = 3.3V PWM 10 0 0.01 0.1 1 OUTPUT CURRENT (A) 10 Figure 8: Efficiency vs. Output Current For V IN = 5V, V OUT = 3.3V at 3A, 94.3% = P OUT / P IN = 94.3% = 0.943 P IN = P OUT / P IN 9.9W / 0.943 10.5W Page 20 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI The power dissipation (P D ) is the power loss in the system and can be calculated by subtracting the output power from the input power. P D = P IN - P OUT = 10.5W - 9.9W 0.6W With the power dissipation known, the temperature rise in the device may be estimated based on the theta JA value ( JA ). The JA parameter estimates how much the temperature will rise in the device for every watt of power dissipation. The EN6338QI has a JA value of 30C/W without airflow. Determine the change in temperature (T) based on P D and JA . T = P D x JA T 0.6W x 30C/W 18C The junction temperature (T J ) of the device is approximately the ambient temperature (T A ) plus the change in temperature. We assume the initial ambient temperature to be 25C. T J = T A + T T J 25C + 18C 43C The maximum operating junction temperature (T JMAX ) of the device is 125C, so the device can operate at a higher ambient temperature. The maximum ambient temperature (T AMAX ) allowed can be calculated. T AMAX = T JMAX - P D x JA 125C - 18C 107C The maximum ambient temperature the device can reach is 107C given the input and output conditions. Note that the efficiency will be slightly lower at higher temperatures and this calculation is an estimate. Page 21 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI APPLICATION CIRCUITS 47nF PGTE BTMP 5V 1.8V @ 3A VOUT PVIN 10 2x 10F 0805 2x 22F 0805 EN6338QI PGND PGND 200k 18pF AVIN VFB EN 10nF VDDB SS 143k 15nF 47nF AGND BGND Figure 9: Smallest Solution Size Application Circuit for V OUT = 1.8V 47nF PGTE BTMP 5V 1.8V @ 3A VOUT PVIN 10 2x 10F 0805 EN6338QI PGND PGND 2x 22F 0805 200k AVIN EN 10nF SS 47pF 3x 100F 0805 VFB VDDB 143k 15nF 47nF AGND BGND Figure 10: Improved Transient Response Application Circuit for V OUT = 1.8V Page 22 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI LAYOUT RECOMMENDATIONS Figure 11 shows critical components and layer 1 traces of a recommended minimum footprint EN6338QI layout. EN and other small signal pins need to be connected and routed according to specific customer application. Visit the Enpirion Power Solutions website at www.altera.com/powersoc for more information regarding layout. Please refer to this Figure 11 while reading the layout recommendations in this section. Figure 11: Top PCB Layer Critical Components and Copper for Minimum Footprint (Top View) Recommendation 1: The input and output filter capacitors should be placed on the same side of the PCB, and as close to the EN6338QI package as possible. The filter capacitors should be connected to the device with very short and wide traces. Do not use thermal reliefs or spokes when connecting the capacitor pads to the respective nodes. The Voltage and GND traces between the capacitors and the EN6338QI should be as close to each other as possible so that the gap between the two nodes is minimized, even under the capacitors. Recommendation 2: The system ground plane should be on the 2nd layer (below the surface layer). This ground plane should be continuous and un-interrupted. Recommendation 3: The ground thermal pad underneath the device must be connected to the system ground plane through as many vias as possible. The drill diameter of the vias should be 0.33mm, and the vias must have at least 1-oz. copper plating on the inside wall, making the finished hole size around 0.2mm to 0.26mm. Do not use thermal reliefs or spokes to connect the vias to the ground plane. This connection provides the path for heat dissipation from the converter. Please see Figure 11. Recommendation 4: Multiple small vias (the same size as the thermal vias discussed in recommendation 4 should be used to connect ground terminal of the input capacitor and output capacitors to the system ground Page 23 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI plane. Put the vias under the capacitors along the edge of the GND copper closest to the Voltage copper. Please see Figure 11. These vias connect the input/output filter capacitors to the GND plane, and help reduce parasitic inductances in the input and output current loops. If the vias cannot be placed under C IN and C OUT , then put them just outside the capacitors along the GND slit separating the two components. Do not use thermal reliefs or spokes to connect these vias to the ground plane. Recommendation 5: AVIN is the power supply for the internal small-signal control circuits. It should be connected to the input voltage at a quiet point. In Figure 11 this connection is made at the input capacitor furthest from the PVIN pin and on the input source side. Avoid connecting AVIN near the PVIN pin even though it is the same node as the input ripple is higher there. Recommendation 6: The V OUT sense point should be connected at the last output filter capacitor furthest from the VOUT pins (near C6). Keep the sense trace as short as possible in order to avoid noise coupling into the control loop. Recommendation 7: Keep R A , C A , R C and R B close to the VFB pin (see Figure 11). The VFB pin is a highimpedance, sensitive node. Keep the trace to this pin as short as possible. Whenever possible, connect R B directly to the AGND pin instead of going through the GND plane. The AGND should connect to the PGND at a single point from the AGND pin to the PGND plane on the 2nd layer. Page 24 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI Figure 12: Landing Pattern with Solder Stencil (Top View) The solder stencil aperture for the thermal PGND pad is shown in Figure 12 and is based on Enpirion power product manufacturing specifications. Page 25 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI PACKAGE DIMENSIONS Figure 13: EN6338QI Package Dimensions Packing and Marking Information: https://www.altera.com/support/quality-and-reliability/packing.html Page 26 15043 August 10, 2018 Rev A Datasheet | Intel(R) Enpirion(R) Power Solutions: EN6338QI REVISION HISTORY Rev A Date Change(s) June, 2018 Initial Release WHERE TO GET MORE INFORMATION For more information about Intel(R) and Enpirion(R) PowerSoCs, visit: www.altera.com/enpirion (c) 2017 Intel Corporation. All rights reserved. Intel, the Intel logo, Altera, ARRIA, CYCLONE, ENPIRION, MAX, MEGACORE, NIOS, QUARTUS, and STRATIX words and logos are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries. Other marks and brands may be claimed as the property of others. Intel reserves the right to make changes to any products and services at any time without notice. Intel assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by Intel. Intel customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or services. * Other marks and brands may be claimed as the property of others. Page 27 15043 August 10, 2018 Rev A