H3CR-AP AC24-48/DC12-48 - Omron Electronics

Solid-State Timer H3CR-A

1/16 DIN Analog-Set Timer with Many

Time Ranges, Operating Modes and

Wide Supply Voltage Range

HField-selectable time ranges from 0.05

second to 300 hours or 0.1 second to

600 hours

HSelect 2-, 4-, or 6-function models to

handle most applications

HWide range AC/DC supply voltage

models (AC100-240/DC100-125 or

AC24-48/DC12-24)

HPNP input now available

HShort, 80 mm (3.15 inch) panel

mounting depth with socket allows

space-efficient control panel design

HChoice of light gray, medium gray, or

black panel covers to match panel

aesthetics

HUL, CSA, CE approved

Ordering Information

JTIMERS

Timing

function

ON-Delay, Repeat cycle

(B, B2), Signal ON/OFF

delay, Signal OFF-delay,

Interval

Signal ON/OFF-

delay, One-shot

Signal ON/OFF-

delay, One-shot

ON-Delay, Repeat cycle

ON, Interval, One-shot

ON-Delay, Repeat cycle

ON, Interval, One-shot

Time range 0.05 s to 300 hr 0.05 s to 300 hr 0.1 s to 600 hr 0.05 s to 300 hr 0.1 s to 600 hr

Terminal form 11-pin round 11-pin round 11-pin round 8-pin round 8-pin round

Part number/

contact output

H3CR-A

AC100-240/DC100-125

H3CR-A-300

AC100-240/DC100-125

H3CR-A-301

AC100-240/DC100-125

H3CR-A8

AC100-240/DC100-125

H3CR-A8-301

AC100-240/DC100-125

H3CR-A

AC24-48/DC12-48

H3CR-A-300

AC24-48/DC12-48

H3CR-A-301

AC24-48/DC12-48

H3CR-A8

AC24-48/DC12-48

H3CR-A8-301

AC24-48/DC12-48

H3CR-AP

AC100-240/DC100-125

— — — —

H3CR-AP

AC24-48/DC12-48

— — — —

Part number/

transistor

output

H3CR-AS

AC24-48/DC12-48

——H3CR-A8S

AC24-48/DC12-48

—

Part number/

time-limiting

— ——H3CR-A8E

AC100-240/DC100-125

—

instantaneous

contact output

— ——H3CR-A8E

AC24-48/DC12-48

—

H3CR-AH3CR-A

JMODEL NUMBER LEGEND

H3CR-Ajjj-j

123 4

1. Terminal Form (Number of Pins)

None: 11-pin models

8: 8-pin models

2. Input Type for 11-pin Models

None: No-voltage input (NPN type)

P: Voltage input (PNP type)

3. Output

None: Relay output (DPDT)

S: Transistor output (NPN/PNP universal use)

E: Relay output (SPDT) with instantaneous relay output

(SPDT)

4. Suffix

300: Dual mode models (signal ON/OFF-delay and one-shot)

301: Double time scale (range) models (0.1 s to 600 h)

JACCESSORIES

Description Part number

Sockets 11-pin Bottom surface or track mounting, top screw terminals P2CF-11

Bottom surface or track mounting, top screw terminals, finger safe terminal conforms to

VDE0106/P100

P2CF-11-E

Back mounting, for use with Y92F-30 mounting adapter, bottom screw terminals P3GA-11

8-pin Bottom surface or track mounting, top screw terminals P2CF-08

Bottom surface or track mounting, top screw terminals, finger safe terminal conforms to

VDE0106/P100

P2CF-08-E

Back mounting, for use with Y92F-30 mounting adapter, bottom screw terminals P3G-08

Terminal cover for P3G sockets, conforms to VDE0106/P100 Y92A-48G

Panel mounting adapter Fits behind panel, ideal for side-by-side installation. Use P3G_-_ sockets Y92F-30

Panel-mounting adapter (88 mm x 58 mm x 66 mm) Y92F-73

Panel-mounting adapter (58 mm x 50 mm x 66 mm) Y92F-74

Protective cover Hard plastic cover protects against dust, dirt and water; not for use with panel covers Y92A-48B

NEMA 4 cover Waterproof front cover Y92A-48N

Colored panel covers Light gray (Munsell No. 5Y7/1) to match case Y92P-48GL

Medium gray (Munsell No. 5Y5/1) Y92P-48GM

Black (Munsell No. N1.5) Y92P-48GB

Time setting rings Used to lock-in a single setting; one ring, can be used with Y92P panel covers Y92S-27

Used to lock-in a setting range; two rings, can be used with Y92P panel covers Y92S-28

Mounting track DIN rail, 50 cm (1.64 ft) length; 7.3 mm thick PFP-50N

DIN rail, 1 m (3.28 ft) length; 7.3 mm thick PFP-100N

DIN rail, 1 m (3.28 ft) length; 16 mm thick PFP-100N2

End plate PFP-M

Spacer PFP-S

H3CR-A H3CR-A

JRANGE AND OPERATION MODE SELECTION

Power indicator (green) (Flashes when Timer

operates; lit when Timer stops operating)

Operating mode display window

Operating mode selector

Select a mode from:

A, B, B2, C, D, and E (H3CR-A, -AP, and -AS)

A, B2, E and J (H3CR-A8, -A8S, and -A8E)

G and J (H3CR-A-300)

Scale range display windows

Time unit display window

Time unit selector (select one

from sec, min, hrs, and 10h)

Time setting

knob (set time)

Output indicator (orange)

(Lit when output is ON)

Time range selector (select one

from 1.2, 3, 12, and 30 at full

scale; with the H3CR-Aj-301,

select from 2.4, 6, 24, or 60 at

full scale.)

Operating Modes

Model H3CR-A/-AS H3CR-AP H3CR-A8/-A8S H3CR-A8E

Operating mode A: ON-delay

B: Repeat-cycle OFF start

B2: Repeat-cycle ON start

C: Signal ON/OFF-delay

D: Signal OFF-delay

E: Interval

G: Signal ON/OFF-delay (Only for H3CR-A-300)

J: One-shot (Only for H3CR-A-300)

A: ON-delay (power supply start)

B2: Repeat-cycle ON start (power supply start)

E: Interval (power supply start)

J: One-shot (power supply start)

Time Ranges

Note: When the time setting knob is turned below “0” until the point where the time setting knob stops, the output will operate instanta-

neously at all time range settings.

Standard (0.05-s to 300-h) Models

Time unit s(sec) min h(hrs) x10 h (10 h)

Full scale

1.2 0.05 to 1.2 0.12 to 1.2 1.2to12

setting 30.3to3 3to30

12 1.2to12 12 to 120

30 3to30 30 to 300

Double (0.1-s to 600-h) Models

Time unit s(sec) min h(hrs) x10 h (10 h)

Full scale

2.4 0.1to2.4 0.24 to 2.4 2.4to24

setting 60.6to6 6to60

24 2.4to24 24 to 240

60 6to60 60 to 600

H3CR-AH3CR-A

Specifications

JRATINGS/CHARACTERISTICS

Item H3CR-A/A8 H3CR-AP H3CR-A8E H3CR-AS/A8S

Rated supply voltage (See

Note 1.)

100-240 VAC (50/60 Hz)/100-125 VDC;

24-48 VAC (50/60 Hz)/12-48 VDC

100-240 VAC (50/60

Hz)/100-125 VDC;

24-48 VAC (50/60

Hz)/12-48 VDC

(See Note 2.)

24-48 VAC (50/60 Hz)/

12-48 VDC

Operating voltage 85% to 110% of rated supply voltage (90% to 110% at 12 VDC)

Power reset Minimum power-opening time: 0.1 s

Power

con-

sumption

100 to 240

VAC/100 to

125 VAC

At 240 VAC, 60 Hz

Relay ON: approx. 2.1

VA (1.6 W)

Relay OFF: approx. 1.3

VA (1.1 W)

At 240 VAC, 60 Hz

Relay ON: approx. 2.5

VA (2.2 W)

Relay OFF: approx. 1.8

VA (1.7 W) (See Note 3.)

At 240 VAC, 60 Hz

Relay ON/OFF:

approx. 2 VA (1 W)

N/A

24-48 VAC/12-

48VDC

At 24 VDC

Relay ON: approx. 0.8 W

Relay OFF: approx. 0.2

At 24 VDC

Relay ON: approx. 0.9 W

Relay OFF: approx. 0.3

At 24 VDC

Relay ON/OFF:

approx. 0.9 W

At 24 VDC

Output ON: 0.3 W

Output OFF: approx.

0.2 W

Inputs

Start, reset and gate

No-voltage Input, NPN

type (H3CR-A only)

ON impedance: 1 kΩ

ON residual voltage: 1V

max.

Off impedance: 100 kΩ

Voltage Input, PNP type

Max. capacity allowed

between input lines

(terminal 6 and 7 or

6 and 8) is 1200µF

—No-voltage Input, NPN

type (H3CR-AS only)

ON impedance: 1 kΩ

ON residual voltage: 1 V

max.

OFF impedance: 100

Ω

min. Load connectable in

parallel with inputs

(terminals 6 and 7 or 6

and 8).

•100 to 240 VAC/100 to

125 VDC

h(lo

ic) level:

kΩmin.

(

)

85 to 264 VAC/

85 to 137.5 VDC

Low (logic) level:

0to10VAC/

0to10VDC

•24 to 48 VAC/

12 to 48 VD

High (logic) level:

20.4- 52.8 VAC/

10.8- 52.8 VDC

Low (logic) level:

0to2.4VAC/

0to1.2VDC

Control

outputs

Time limit Relay output (DPDT) Relay output (DPDT) Relay output (SPDT) Transistor output

(See Note 5.)

Instantaneous — — Relay output (SPDT) —

Max. load 5 A at 240 VAC/30 VDC, resistive load (cos φ=1)

max. load

5 A at 250 VAC

resistive load

(cos φ=1)

100 mA max. at 30 VDC

max.

Min. load 10 mA at 5 VDC —

Residual

voltage

— — — 2Vmax.

Repeat accuracy ±0.2% FS max. (±0.2%±10 ms max. in a range of 1.2 s)

Setting error ±5% FS ±50 ms (See Note 4.)

Note: 1. DC ripple rate: 20% max. if the power supply incorporates a single-phase, full-wave rectifier.

2. The 24 to 48 VAC/12 to 48 VDC model causes an inrush current of approximately 0.85 A. Take precaution when applying power

to these models, especially if there is a non-contact output like a sensor.

3. The values are for when the terminals 2 and 7 and terminals 10 and 6 are shorted, and include the consumption current of the

input circuit.

4. The value is ±5% FS +100 ms to 0 ms max. when the C, D, or G mode signal of the H3CR-AP is OFF.

5. The internal circuits are optically isolated from the output. This enables universal application as NPN or PNP transistor.

H3CR-A H3CR-A

Item H3CR-A/A8 H3CR-AP H3CR-A8E H3CR-AS/A8S

Reset time Min. power-opening time: 0.1 s max.

Min. pulse width: 0.05 s (H3CR-A/-AS)

Reset voltage 10% max. of rated voltage

Resetting system Power OFF, external, self resetting (11-pin models); Power OFF (8-pin models)

Indicators Power ON indicator (green LED), Output ON indicator (orange LED)

Material Plastic case (light gray Munsell 5Y7/1) and knob (clear)

Mounting method DIN track mounting, surface mounting, and flush mounting

Connection 11-pin (H3CR-A)

8-pin (H3CR-A8)

11-pin 8-pin 11-pin (H3CR-AS)

8-pin (H3CR-A8S)

Weight Approx. 90 g (3.17 oz)

Approved standards UL508, CSA C22.2 No.14, NK, Lloyds

Conforms to EN61812-1 (VDE0435/P2021), IEC60664-1 (VDE0110) 4kV/2, EN60947-5-1 (contact

output), and EN60947-5-2 (non-contact output).

Ambient Operating -- 1 0 °Cto55°C(14°F to 131°F) with no icing

temperature Storage -- 2 5 °Cto65°C (-13°F to 149°F) with no icing

Ambient

humidity

Operating 35% to 85%

Variation due to voltage

change

±0.2% FS max. (±0.2% ±10 ms max. in a range of 1.2 s)

Variation due to

temperature change

±1% FS max. (±1% ±10 ms max. in a range of 1.2 s)

Insulaton resistance 100 MΩmin. (at 500 VDC)

Vibration resistance Destruction: 10 to 55 Hz with 0.75-mm double amplitude each in 3 directions for 2 hours each

Malfunction: 10 to 55 Hz with 0.5-mm double amplitude each in 3 directions for 10 minutes each

Shock resistance Destruction: 1,000 m/s2(approx. 100G) 3 times each in 6 directions

Malfunction: 100 m/s2(approx. 10G) 3 times each in 6 directions

Static immunity Malfunction: 8 kV

Destruction: 15 kV

Dielectric strength 2,000 VAC (1,000 VAC for H3CR-AjS), 50/60 Hz for 1 min between current-carrying metal parts and

exposed non-current-carrying metal parts

2,000 VAC (1,000 VAC for H3CR-AjS), 50/60 Hz for 1 min between control output terminals and

operating circuit

2,000 VAC, 50/60 Hz for 1 min between contacts of different polarities

1,000 VAC, 50/60 Hz for 1 min between contacts not located next to each other

2,000 VAC, 50/60 Hz for 1 min between input and control output terminals and operation circuit

Impulse withstand voltage 3 kV (between power terminals) for 100 to 240 VAC/100 to 125 VDC; 1 kV for 24 to 48 VAC/12 to 48 VDC

4.5 kV (between current-carrying terminal and exposed non-current-carrying metal parts) for 100 to

240 VAC/100 to 125 VDC; 1.5 kV for 24 to 48 VAC/12 to 48 VDC and 24 to 48 VAC/VDC

EMC (EMI) EN50081-2

Emission enclosure: EN55011 Group 1 class A

Emission AC mains: EN55011 Group 1 class A

(EMS) EN50082-2

Immunity ESD: EN61000-4-2: 4 kV contact discharge (level 2)

8 kV air discharge (level 3)

Immunity RF-interference from AM radio waves: ENV50140: 10 V/m (80 MHz to 1 GHz) (level 3)

Immunity RF-interference from pulse-modulated radio waves: ENV50204: 10 V/m (900±5MHz)

(level 3)

Immunity conducted disturbance: ENV50141: 10 V (0.15 to 80 MHz) (level 3)

Immunity burst: EN61000-4-4: 2 kV power-line (level 3)

2 kV I/O signal-line (level 4)

Immunity surge: EN61000-4-5: 1 kV line to line

2 kV line to ground (level 3)

Degree of protection IP40 (front face)

Life Mechanical 20,000,000 operations min. (under no load at 1,800 operations/h)

expectancy Electrical 100,000 operations min. (5 A at 250 VAC, resistive load at 1,800 operations/h)

H3CR-AH3CR-A

ineerin

Data

Note: A maximum current of 0.15 A can be switched at 125 VDC (cosφ= 1) and

a maximum current of 0.1 A can be switched if L/R is 7 ms. In either case,

a service life of 100,000 operations can be expected. The minimum appli-

cable load is 10 mA (100 mA for H3CR-A8E) at 5 VDC (failure level: P).

Load current (A)

30 VDC L/R = 7 ms

250 VAC/30 VDC

(cosφ=1)

250 VAC (cosφ=0.4)

Switching operations (x 10 )

10,000

5,000

1,000

500

100

Timin

Charts

Note: 1. The minimum power-opening time (“Rt”) is 0.1 s and the minimum pulse width is 0.05 s.

2. The letter “t” in the timing charts stands for the set time and “t--a” means that the period is less than the time set.

H3CR-A/-AS/-AP

Operating

mode

Timing chart

A: ON-delay

Power

Start

Output

Basic operation

Power

Start

Reset

Output relay

(NC)

Output relay

(NO) (Output

indicator)

Power

indicator

t t

Repeat-cycle

OFF start Power

Output relay

(NO) (Output

indicator)

Power indicator

Start

Reset

Output relay

(NC)

Basic operation

Power

Start

Output

t t t t

tt ttt

t--a

H3CR-A H3CR-A

Operating

mode

Timing chart

B2:

Repeat-cycle

ON start Basic operation

Power

Start

Output

t t t t

Power

Start

Reset

Output relay

(NO) (Output

indicator)

Power indicator

Output relay

(NC)

tt ttt

t--a

Signal

ON/OFF-

delay Basic operation

Power

Start

Output

tt tt

Power

Start

Reset

Output relay

(NC)

Power

indicator

Output relay

(NO) (Output

indicator)

tt t t

t--a t--a t--a

Signal

OFF-delay

Basic operation

Power

Start

Output

Output relay

(NC)

Power

indicator

Power

Start

Reset

Output relay

(NO) (Output

indicator)

t--a

t--a t--a

Interval

Power

Start

Output

Basic operation

Power

Start

Reset

Output relay

(NC)

Power

indicator

Output relay

(NO) (Output

indicator)

t--a t--a

Signal

ON/OFF-

delay Basic operation

Power

Start

Reset

Output relay

(NC)

Power

indicator

Power

Output

Start

Output relay

(NO) (Output

indicator)

tt tt

t--at--a

H3CR-AH3CR-A

H3CR-A/-AS/-AP (continued)

Operating

mode

Timing chart

One-shot

output

Basic operation

Power

Start

Reset

Output relay

(NC)

Power

indicator

tt--a t--a

1±0.6 s

(Fixed) t1±0.6 s

(Fixed)

Output

Start

Power

Output relay

(NO) (Output

indicator)

1±0.6 s

(Fixed)

H3CR-A8/-A8S

Operating

mode

Timing chart

ON-delay

Power

Output

Basic operation

Power

Output relay

(NC)

Output relay

(NO) (output

indicator)

Power

indicator

tRt tRt t -- a

B2:

Repeat-cycle

ON start Power

Output relay

(NC)

Output relay

(NO) (output

indicator)

Power

indicator

Power

Output

Basic operation

t t t

tt t tt

Rt t--a

t--a

Interval

Power

Output

Basic operation

tRt tRt t -- a

Power

Output relay

(NC)

Power

indicator

Output relay

(NO) (output

indicator)

One-shot

output Power

Output relay

(NC)

Output relay

(NO) (output

indicator)

Power

indicator

Power

Output

Basic operation

1±0.6 s

(Fixed)

tRt t

t--a

H3CR-A H3CR-A

H3CR-A8E

Operating

mode

Timing chart

ON-delay

Power

Output

Basic operation

Power

Output relay

(NC)

Power indicator

Instantaneous

output relay (NC)

tRt tRt t -- a

Instantaneous

output relay (NO)

Output relay

(NO) (output

indicator)

B2:

Repeat-cycle

ON start Power

Output relay

(NC)

Power indicator

Instantaneous

output relay (NC)

Instantaneous

output relay (NO)

Output relay

(NO) (output

indicator) Power

Output

Basic operation

t t t

ttt

t--a

Interval Power

Output relay

(NC)

Power indicator

tRt tRt t -- a

Instantaneous

output relay (NC)

Instantaneous

output relay (NO)

Output relay

(NO) (output

indicator)

Power

Output

Basic operation

One-shot

output Power

Output relay

(NC)

Power indicator

Instantaneous

output relay (NC)

Instantaneous

output relay (NO)

Output relay

(NO) (output

indicator)

Power

Output

Basic operation

1±0.6 s

(Fixed)

Rt Rt

t--a

H3CR-AH3CR-A

JAPPLICATION EXAMPLES

A Mode: ON-delay

ON-delay operation (A mode) is a basic mode.

1. Power-ON Start/Power-OFF Reset

The power-ON start/Power-OFF reset operation is a standard

operating method. The start terminals are connected. Timing

starts when power is applied. The output is energized when the

accumulated time equals the set time. The output relay or

transistor remains energized until power is disconnected or a

reset input is applied. The minimum resetting time is 0.1 second.

Power (2 and 10)

Start (2 and 6)

Control output: NC (8 and 11)

NC (1 and 4)

Control output:NO (9 and 11)

NO (1 and 3)

Power indicator

Flashing Lit

Externally short-circuited

Power

supply

2. Signal Start/Signal Reset

The signal start/Signal reset operation is useful for remote control

of the Timer. Power is applied continuously. Timing starts at the

leading edge of the start input. The output relay is energized

when the accumulated time equals the set time. Subsequent start

signals that occur during or after timing will not be accepted. The

output relay or transistor will remain energized until a reset input

is applied or power is interrupted. The minimum signal input is

0.05 second.

Power (2 and 10)

Start (2 and 6)

Control output: NC (8 and 11)

NC (1 and 4)

Control output: NO (9 and 11)

NO (1 and 3)

Power indicator

Flashing Lit

Reset (2 and 7)

Lit

(Power continuously supplied)

Start signal (remote control possible)

Reset signal

(remote control possible)

Power

supply

3. Cumulative Timing Using the Gate Input with ON-Delay

With a gate signal, the Power-ON start operation and Signal start

operation can be controlled (the operation can be interrupted).

When the gate signal is closed, timing is temporarily stopped.

When the gate signal opens, timing resumes at the point of

interruption. The gate input terminal permits the timer to sum up

times t1and t2as shown in the timing chart.

Power (2 and 10)

Start (2 and 6)

Control output: NC (8 and 11)

NC (1 and 4)

Control output: NO (9 and 11)

NO (1 and 3)

Power indicator

Power

supply

Flashing Lit

Gate (2 and 5)

Gate signal (The operation is interrupted with the

gate signal if the Timer detects an abnormal signal.)

Externally

short-circuited

t1t2t1+t

2:settime

H3CR-A H3CR-A

B/B2 Mode: Repeat Cycle

The repeat cycle operation in the B and B2 modes can be

effectively applied to lamp or buzzer (ON and OFF) alarms or the

monitoring of an intermittent operation with a display.

1. Power-ON Start/Power-OFF Reset

The start terminals are connected. Timing starts when power is

applied. The output relay or transistor operates according to

mode B (OFF/ON/OFF pattern) or mode B2 (ON/OFF/ON

pattern), whichever is set. The cycle repeats until a reset input is

applied or power is disconnected.

Power (2 and 10)

Start (2 and 6)

Control output: NC (8 and 11)

NC (1 and 4)

Control output: NO (9 and 11)

NO (1 and 3)

Power indicator

Flashing

Externally short-circuited

Power

supply

2. Signal Start/Signal Reset

If there is an abnormal signal, flashing starts. When the abnormal

condition is restored, a reset signal stops the display flashing.

Power is continuously applied. The ON/OFF cycle is initiated at

the leading edge of the start input.

In Mode B the output relay or transistor will be OFF for the set

time and then ON for the set time, creating an operation pattern

of OFF/ON/OFF.

In Mode B2 the output relay or transistor will turn ON for the set

time and then OFF for the set time, creating an operation pattern

of ON/OFF/ON. This cycle will be repeated until a reset input is

applied or power is disconnected. The minimum signal input time

is 0.05 second.

Power (2 and 10)

Start (2 and 6)

Control output: NC (8 and 11)

NC (1 and 4)

Control output: NO (9 and 11)

NO (1 and 3)

Power indicator

Reset (2 and 7)

Lit Flashing Lit

(Power continuously supplied)

Start signal

Reset signal

Power

supply

C Mode: Signal ON/OFF-delay

The Signal ON-/OFF-delay operation (C mode) is useful for the

control of distribution of products on a production line into boxes

by the specified number or time.

1. Power-ON Start/Instantaneous Operation/Time-limit Reset

The timing cycle starts when power is applied. When the timer

reaches set point, the output status changes and holds that

status until power turns OFF to reset the timer. Minimum reset

time is 0.1 second.

Power (2 and 10)

Start (2 and 6)

Control output: NC (8 and 11)

NC (1 and 4)

Control output: NO (9 and 11)

NO (1 and 3)

Start signal (NC to NO)

Power

supply

2. Signal-ON-OFF Start/Instantaneous Operation/Time-limit

Reset

Power is continuously applied. The first timing cycle begins when

the input signal is applied, the second when it is removed. The

output relay or transistor is energized when the lapsed time from

the first timing cycle equals the set point. The output remains

energized until the lapsed time of the second timing cycle equals

the set point. The minimum signal input time is 0.05 second.

Power (2 and 10)

Start (2 and 6)

Control output: NC (8 and 11)

NC (1 and 4)

Control output: NO (9 and 11)

NO (1 and 3)

Power indicator

Flashing

Lit

Start signal

(The operation starts with the signal ON or OFF)

Lit

(Power continuously supplied)

Power

supply

H3CR-AH3CR-A

3. Signal Start/Instantaneous Operation/Time-limit Reset

Power is continuously applied. The output relay is energized at

the leading edge of the start input. Timing starts at the trailing

edge of the start input. The output relay is de-energized when the

accumulated time equals the set time. The minimum signal input

time is 0.05 second.

Lit

Start signal (NO to NC to NO)

Power (2 and 10)

Start (2 and 6)

Control output: NC (8 and 11)

NC (1 and 4)

Control output: NO (9 and 11)

NO (1 and 3)

Power indicator

Flashing Lit

(Power continuously supplied)

Power

supply

D Mode: Signal OFF-delay

Signal OFF-delay operation (D mode) can be effectively used to

keep a load operating for a certain period. For example, this

function enables the cooling fan for a lamp or heater to operate

for a certain period after the lamp or heater is switched OFF.

Power-ON Start/Instantaneous Operation/Time-limit Reset

Power is continuously applied. The output relay is energized at

the leading edge of the start input. Timing starts at the trailing

edge of the start input. The output is de-energized when the

accumulated time equals the set time. The minimum reset time is

0.1 second.

Power (2 and 10)

Start (2 and 6)

Control output: NC (8 and 11)

NC (1 and 4)

Control output: NO (9 and 11)

NO (1 and 3)

Power indicator

Lit Flashing

Start signal (NC to NO)

Power

supply

Lit

E Mode: Interval

1. Signal Start/Instantaneous Operation/Time-limit Reset

This function is useful for the repetitive control such as the filling

of liquid for a specified period after each Signal start input. Timing

begins on the leading edge of the start signal. The control output

is only energized during timing. The timer is reset when a reset

signal is applied.

Start signal

(Power continuously supplied)

Power

supply

Power (2 and 10)

Start (2 and 6)

Control output: NC (8 and 11)

NC (1 and 4)

Control output: NO (9 and 11)

NO (1 and 3)

t t

2. Power-ON Start/Instantaneous Operation/Time-limit Reset

Timing begins on the leading edge of the start signal. The control

output is only energized during timing. The timer is reset when a

reset signal is interrupted.

Power (2 and 10)

Start (2 and 6)

Control output: NC (8 and 11)

NC (1 and 4)

Control output: NO (9 and 11)

NO (1 and 3)

Power

supply

Start signal (NC to NO)

H3CR-A H3CR-A

Dimensions

Unit: mm (inch)

JTIMERS

(1.54)

dia.

11-Pin

H3CR-A

H3CR-AP

H3CR-AS

8-Pin

H3CR-A8

H3CR-A8S

H3CR-A8E 66.6

52.36

44.8 x 44.8

(1.76 x 1.76)

0.7

(1.89)

(0.59) 66.6

(2.62)

Dimensions with Y92S Set Ring

and Y92P Panel Cover

Time Setting

Ring

Panel cover

(1.65)

dia.

(1.97)

16.5

(0.65)

JPANEL-MOUNTING ADAPTERS

Dimensions with Panel-Mounting Adapter

Y92F-30

Panel Cutout

Note: 1. The Adapters for two or more timers mounted in a vertical line are different in orienta-

tion from those mounted in a horizontal line.

N can be obtained as follows (n: the number of H3CR models arranged side by side)

Without a Cover: N = (48n -- 2.5) +1/-- 0

With the Protective Cover: N = (51n -- 5.5) +1/-- 0

With the Panel Cover: N = (50n -- 4.5) +1/-- 0

2. The mounting panel thickness should be 1 to 5 mm.

0.5 R max. 45+0.6

-- 0

45+0.6

-- 0

(N)

Panel

(2.28)

(1.89)

(2.05)

Y92F-30 Adapter

P3GjSocket

H3CR-AH3CR-A

Dimensions with Panel-Mounting Adapter

Y92F-73

Dimensions with Panel-Mounting Adapter

Y92F-74

Panel

45±0.15

45±

0.15

Panel

43±0.2

45±0.2

50+0.2

-- 0

Panel Cutout

Note: The mounting panel thickness

should be 1 to 3.2 mm.

Adapter mounting hole Two, 4.5 dia.

52 to 53

76±0.265 to 66

R0.5 max.

R0.5 max. 45+0.5

-- 0

55+0.5

-- 0

Note: The mounting panel thickness

should be 1 to 3.2 mm.

(3.46)

(2.28)

(2.20)

(2.68)

JTRACK MOUNTING

Dimensions with Front-Connecting Socket

P2CF-08/P2CF-11

P2CF-08-E/P2CF-11-E

*These dimensions vary with the kind of DIN track (reference value).

H3CR-A

H3CR-AS

H3CR-A8j

P2CF-11(E) P2CF-08(E)

100.8*

(3.97)

98.5

(3.88)

2.3*

(0.09)

89.9*

(3.54)

87.6

(3.45)

2.3*

(0.09)

JPANEL MOUNTING

H3CR-A

H3CR-AS

Adapter

H3CR-A8j

Adapter

Y92F-30 P3GA-11 Y92F-30 P3G-08

Dimensions with Back-Connecting Socket

P3G-08/P3GA-11

(3.15) 75

(2.95)

(0.59)

H3CR-A H3CR-A

JACCESSORIES (ORDER SEPARATELY)

Track Mounting/

Front-Connecting Socket

Terminal Arrangement/

Internal Connections

(Top View) Surface Mounting Holes

40±0.2

Two,4.5dia.ortwo,M4

Eight,

M3.5 x 7.5 sems

Two, 4.5 dia.

holes

7.8

(0.31)

70 max.

(2.76)

(0.16) 50 max.

(1.97)

(0.12)

4.5

(0.18)

35.4

(1.39)

20.3 max.

(0.80)

P2CF-08-E Socket

(Finger-Safe Terminal Type)

Conforming to VDE0106/P100

P2CF-08

4.5

35.4

21.5 max.

7.8

70 max.

50 max.

40 ±0.2

Two,

4.5

dia.

holes

Eight

M3.5 X 7.5 sems

1.3

20.3

(1.23)

max.

P2CF-11 Socket

Two, 4.5 dia. mounting holes

40±0.2

Two, 4.5 dia.

holes

Eleven,

M3.5 x 7.5 sems

7.8

(0.31)

70 max.

(2.76)

(0.16) 50 max.

(1.97)

(0.12)

4.5

(0.18)

35.4

(1.39)

P2CF-11-E Socket

(Finger-Safe Terminal Type)

Conforming to VDE0106/P100

4.5

35.4

1.2

7.8

max.

40 ±0.2

Two,

4.5

dia.

holes

Eight

M3.5 X 7.5 sems 5

50 max.

31.2

(1.23)

max.

H3CR-AH3CR-A

Back-Connecting Socket

P3GA-11

Terminal Arrangement/

Internal Connections

(Bottom View)

4.9

(0.19) 17

(0.67)

27 dia.

(1.06)

(1.77)

25.6

(1.01)

4.5

(0.18)

6.2

(0.24)

16.3

(0.64)

(1.77)

27 dia.

(1.06)

P3G-08

JPROTECTIVE COVERS

Finger-Safe Terminal Cover for P3G(A)

Y92A-48G

27.6

16.5

47.4

48 x 48

47.7

x4.47

Twelve, 6.4 dia. holes

Conforming to VDE0106/P100

Y92A-48B

The protective cover protects the front panel, particularly the time

setting section, against dust, dirt, and water. It also prevents the

set value from being altered due to accidental contact with the

time setting knob.

Note: 1. The Y92A-48B Protective Cover is made of a hard

plastic and therefore it must be removed to change the

timer set value.

2. The Protective Cover cannot be mounted if the Panel

Cover (sold separately) is used on the Timer.

3. When using a front cover for flush mounting, use the

Y92F-30 Adapter. The Y92F-73 or Y92F-74 Flush

Mounting Adapter cannot be used.

Y92A-48B

H3CR-A H3CR-A

Time Setting Ring/Panel Cover

There are three colors of Panel Covers (Y92P-48GL (light gray),

Y92P-48GB (black), and Y92P-48GM (medium gray). Use the

most suitable type of Panel Cover with the design of the scaling

plate according to the application.

When setting a given time for the Timer, use of the Y92S-27 or

Y92S-28 Time Setting Ring facilitates the time setting operation

and minimizes possible setting errors by operators.

The Y92F-73 or Y92F-74 Panel-Mounting Adapter or the

Y92A-48B Protective Cover cannot be used.

The Time Setting Ring and Panel Cover should be used as a pair.

Setting a specific time Time Setting Ring A (Y92S-27) and

Panel Cover (Y92P-48GL, -48GB, or

-48GM)

Limiting the setting

range

Time Setting Ring B or C (Y92S-28),

and Panel Cover (Y92P-48GL, -48GB,

or -48GM)

Y92S-27

Time Setting A

Y92S-28

Time Setting B

Y92P-48GL

Light Gray

Y92P-48GB

Black

Y92P-48GM

Medium Gray

Y92S-28

Time Setting C

Y92H-8

For PF085A Socket

Hold-Down Clip

Y92H-7

For PL08 and PL11 Sockets

JMOUNTING TRACK

PFP-100N, PFP-50N PFP-100N2

L: Length

1 m PFP-100N

50 cm PFP-50N

1 m PFP-100N2

15 25 25 25 25 *

10 10

7.3±0.15

35±0.3 27±0.15

15 25 25 25 25 15

10 10

35±0.3 27 24

4.5

(0.18)

4.5

(0.18)

(0.04)

1.5

(0.06)

(0.63)

29.2

(1.15)

End Plate Spacer

M4 x 8

pan head

screw

135.5

1.8

(1.97)

11.5

(0.45) 10

(0.39) 4.8 (0.19)

1.3 (0.05)

35.3

(1.39)

1.8

(0.07)

(0.39)

6.2

(0.24)

(0.20)

44.3

(1.74)

16.5

(0.65)

34.8

(1.37)

(0.63)

PFP-M PFP-S

H3CR-AH3CR-A

onnections

JINPUT/OUTPUT FUNCTIONS

Models H3CR-A, H3CR-AP and H3CR-AS

Name Type Description

Start input* No-voltage contact closure Initiates timing

Reset input No-voltage contact closure Interrupts time measurement and resets the operation to start. No time

measurement is made and the control output is OFF while the reset input is ON.

Gate input No-voltage contact closure Inhibits time measurement. Timing resumes when the gate input is turned OFF.

Control output Relay or transistor Turns ON and OFF when the preset value is reached, according to the operation

mode selected.

Note: *H3CR-AP models offer Start input only and use a PNP voltage input.

Gate signal

input Power

Start

Gate

Reset

Output

relay

OFF

Note: 1. This timing chart indicates the gate input in operating mode A (ON-delay operation).

2. The set time is the sum of t1and t2.

t1t2

JCONNECTION SUMMARY

Part

Input terminal numbers Power supply terminal numbers Output terminal numbers

number Gate Start Reset 0V AC (common), DC-- AC (hot), DC+ Type COM NC NO

H3CR-A 56722 10 Timed contact 143

Timed contact 11 8 9

H3CR-AP -- 6-- 7 2 10 Timed contact 143

Timed contact 11 8 9

H3CR-AS 56722 10 Transistor

(NPN/PNP)

11 -- 9

H3CR-A8 -- -- -- -- 2 7 Timed contact 143

Timed contact 856

H3CR-A8E -- -- -- -- 2 7 Timed contact 143

Instantaneous

contact

856

H3CR-A8S -- -- -- -- 2 7 Transistor

(NPN/PNP)

8-- 6

H3CR-A H3CR-A

JTERMINAL ARRANGEMENT

Note: The delayed contact of conventional Timers was indicated as

The contact symbol of the H3CR-A is indicated as because its operating mode is five multi-modes (four multi-modes for the

H3CR-A8).

11-pin Models 8-pin Models

H3CR-A (Contact Output)

Reset input

Start input

Gate input

(--)(~) (+)(~)

H3CR-A8 (Contact Output)

(--)

(~)

(+)

(~)

Power supply

H3CR-AS (Transistor Output)

(--)(~) (+)(~)

Reset input

Start input

Gate input

Note: Terminals 1, 3, 4, and 8 are empty. Terminals 2, 5, 6,

7, and 10 are the same as for the H3CR-A.

H3CR-A8S (Transistor Output)

(--)

(~)

(+)

(~)

Note: Terminals 1, 3, 4, and 5 are empty. Terminals 2 and 7

are the same as for the H3CR-A8.

Power supply

H3CR-AP (Contact Output)

(--)(~) (+)(~)

Start input

Note: Terminal 5 is empty.

H3CR-A8E (Contact Output)

(--)

(~)

(+)

(~)

Power supply

H3CR-AH3CR-A

JINPUT CONNECTIONS

H3CR-A/-AS

The inputs of the H3CR-A/-AS are no-voltage (short-circuit or open) inputs.

(Connection to NPN open

collector output sensor.)

(Connection to a voltage

output sensor.)

No-voltage Inputs

12 to 24 VDC

(sensor power supply)

Sensor Timer

5Gate

6Start

7 Reset

2 Input (0 V)

Operates with transistor ON

DC power

supply

Operates with relay ON

12 to 24 VDC

(sensor power supply)

Sensor

Operates with transistor ON

DC power

supply

5Gate

6Start

7 Reset

2 Input (0 V)

5Gate

6Start

7 Reset

2 Input (0 V)

Timer Timer

•No-contact Input •Contact Input •No-contact Input

H3CR-AP

The start input of the H3CR-AP is voltage input. (Voltage imposition or open)

(Connection to PNP open

collector output sensor)

(Connection to NPN open

collector output sensor)

12 to 24 VDC

(sensor power supply)

Sensor

Timer

6Start

Operates with PNP transistor ON Operates with NPN transistor ON

12 to 24 VDC

(sensor power supply)

Timer

Sensor

Timer

Operates with relay ON

Note: Refer to the signal levels in the fol-

lowing table and be aware of the

minimum applicable load of the

relay.

Voltage Inputs

10 Power

supply (+)

7 Input 0V

6Start

10 Power

supply (+)

7 Input 0V

2 Power

supply

(--)

2 Power

supply

(--)

AC power supply

DC power supply

6Start

10 Power

supply (+)

7 Input 0V

2Power

supply

(--)

DC power

supply

-- DC power

supply

Note: The input circuit is isolated from the

power supply circuit. Thus, an NPN

transistor can be connected.

•No-contact Input •Contact Input•No-contact Input

H3CR-A H3CR-A

Installation

JCHANGING THE SETTING

Do not change the time unit, time range, or operation mode while

the Timer is in operation, or the Timer may malfunction.

The time unit and time range can be set with the respective

selectors turned clockwise or counterclockwise.

The selectors are notched so that they will snap when they are

properly set. Do not set the selectors midway between notches,

or the Timer may break or malfunction.

JPOWER SUPPLIES

Pay the utmost attention not to make mistakes in polarity when

wiring the Timer.

The H3CR Series uses a transformerless power supply. Do not

touch the input terminals while the supply voltage is applied, or

an electric shock may be received.

A DC power supply can be connected if its ripple factor is 20% or

less and the mean voltage is within the rated operating voltage

range of the Timer.

Be aware that the operating voltage will rise by 5% if the rated

voltage is applied to the Timer continuously while the ambient

temperature is close to the maximum permissible ambient

temperature.

For the power supply of an input device of the H3CR-A/-AS, use

an isolating transformer with the primary and secondary windings

mutually isolated and the secondary winding not grounded.

Example: H3CR-A

H3CR-A

Input

terminal Power supply

Circuit

Isolating transformer

is not required.

Rectifier circuit

The power supply terminal 2 of H3CR-A/-AS is a common

terminal for input signals to the Timer. Do not disconnect the

wires on terminal 2, or the internal circuitry of the H3CR-A/-AS

will be damaged.

H3CR-A

Input terminal

5, 6, 7

G, S, R

An AC power supply can be connected to the power input

terminals without regard to polarity. A DC power supply must be

connected to the power input terminals as designated according

to the polarity of the terminals.

Make sure that the voltage is applied within the specified range,

or the internal elements of the Timer may be damaged.

Connect the power supply voltage through a relay or switch in

such a way that the voltage reaches a fixed value at once, or the

Timer may not be reset, or a timer error may result.

H3CR-AH3CR-A

JINPUT/OUTPUT

Relationship between Input and Power Supply

Circuits (H3CR-A/-AS)

The H3CR-A/-AS uses transformerless power supply. When

connecting a relay or transistor as an external signal input

device, pay attention to the following points to prevent

short-circuiting due to a sneak current to the transformerless

power supply. If a relay or transistor is connected to two or more

Timers, the input terminals of those Timers must be wired

properly so that they will not differ in phase, or the terminals will

be short-circuited to one another.

Input

terminal Power supply

H3CR-A

Input

terminal

Contact or transistor for

external input signal

Short-circuit

current

Input

terminal

Power supply

Input

terminal

Incorrect

Correct

It is impossible to provide two independent power switches as

shown below regardless of whether the Timers are different in

phase.

Input

terminal Power supply

Input

terminal

An appropriate input is applied to the input signal terminals of the

H3CR-A/-AS when one of the input terminals is short-circuited

with the common terminal (terminal 2) for the input signals. Do

not attempt to connect the input terminal to any terminal other

than the common terminal or to apply voltage across terminals

other than the specified input and common terminals, or the

internal circuitry of the Timer will be damaged.

Input terminal

H3CR-A

Input

contact

AC or DC

power supply

(2.)

(See Note 1.)

5, 6, 7

G, S, R

Note: 1. Power supply terminal 2 is a common terminal for input

signals to the Timer. Never use terminal 10 as the com-

mon terminal for this purpose, or the internal circuit of

the Timer will be damaged.

2. Do not connect a relay or any other load between

these terminals, or the internal circuit of the Timer will

be damaged due to the high-tension voltage applied to

the input terminals.

Relationship between Input and Power Supply Cir-

cuits (H3CR-AP)

Input circuit Power supply

circuit

AC/DC

power

supply

H3CR-AP

Since the input circuit and the power supply circuit are configured

independently, the input circuit can be turned ON or OFF

irrespective of the ON/OFF state of the power supply.

It must be noted that a voltage equivalent to the power supply

voltage is applied to the input circuit.

When connecting a relay as an external signal input device, pay

attention to the following points to prevent short-circuiting due to

a sneak current to the transformerless power supply.

H3CR-A H3CR-A

If a relay or transistor is connected to two or more Timers, the

input terminals of those Timers must be wired properly so that

they will not be different in phase or the terminals will be

short-circuited to one another (refer to the figures below).

Incorrect Contact or transistor for

external input signal

Correct

H3CR-AP Power supply

Contact or transistor for

external input signal

H3CR-AP

Power supply

H3CR-AP

CommontoAllModels

The input wires must be as short as possible. If the floating

capacity of wires exceeds 1,200 pF (approx. 10 m for cables with

120 pF/m), the operation will be affected. Pay particular attention

when using shielded cables.

The H3CR-AjS transistor output is isolated from the internal

circuitry by a photocoupler. Therefore, either NPN or PNP output

is possible.

The power supply circuit of the H3CR-A Series (except for

H3CR-AjS) is a switching circuit. If the power line connected to

the power supply circuit has a transformer with high inductance,

a counter-electromotive voltage will be induced. To suppress the

voltage, apply a CR filter to the power supply line.

Do not set the dial to minimum in repeat cycle mode (B, B2) or

the contacts may be damaged.

H3CR-AH3CR-A

eration

JBASIC SETTING

Setting of Selector

The selectors can be turned clockwise and counterclockwise to

select the desired time unit, time range, or operating mode.

Each selector has a snap mechanism that secures the selector at

a given position. Set the selector at a position at which it is

secured. Do not set it midway between two securing positions or

a malfunction could result from improper setting.

Groove for

screwdriver

Operating mode

display window

Operating mode

selector

Selection of Operating Mode

Turn the operating mode selector with a screwdriver until the

desired operating mode (H3CR-A/AP/AS: A, B, B2, C, D, or E,

H3CR-A8/A8S/A8E: A, B2, E or J, H3CR-A-300: G or J) appears

in the display window located above the selector.

Selection of Time Unit and Time Range

The desired time unit (sec, min, hrs, or 10h) is displayed in the

window below the time setting knob by turning the time unit

selector located at the lower right corner of the front panel. A time

range (1.2, 3, 12, or 30/2.4, 6, 24, or 60 for H3CR-Aj-301) is

selected with the time range selector at the lower left corner of

the front panel, and the selected time range appears (in the

window at the lower right part) within the plastic frame of the time

setting knob.

Scale range

display window

Time unit selector

Time unit display window

Time range

selector

Time setting

knob

Setting of Time

Use the time setting knob to set the desired time.

JTIME SETTING RINGS

Time setting rings allow the operator to lock in a selected, preset

time. They must be used with Y92P Panel Covers. Each ring fits

snugly around the time setting knob. A notch on the ring engages

the tab on the panel cover to prevent setting knob travel. Omron

offers two types of time setting rings in medium gray. The

Y92S-27 setting ring is used for a single set point. The Y92S-28

pair of rings are used to lock in two set points for a timing range.

Y92S-27 Setting a Single Preset

In this example, the time setting will be locked at 10 minutes:

Select timing function and set unit of measure to “min”. Install the

panel cover. Turn the time setting knob to 10. Align the notch on

the ring with the tab then press the ring onto the time setting

knob.

Time setting

notch Reset lock position

Time Setting

Ring Y92S-27 Panel cover

Example: To set the time to 10 s.

Time setting notch Setting position

Y92S-28 Limiting the Setting Range

In this example, the timing range of 10 to 20 minutes will be

locked in using the two rings in Y92S-28:

Set the timing function and set unit of measure to “min”. Turn the

setting knob to 10. Align the thinner ring’s tab with the right side

of the panel cover tab. Press the ring onto the time setting knob

to set the lower limit. Turn the time setting knob to 20. Align the

thicker ring’s tab with the left side of the panel cover tab. Press

the ring onto the time setting knob to set the upper limit.

Stopper Reset lock position

Time Setting

Y92S-28

Time Setting

Y92S-28

Panel cover

Range

H3CR-A H3CR-A

Mounting

JPANEL MOUNTING

Using Y92F-30 Adapter

Insert the timer through the panel cutout. Push the Y92F-30

adapter from the rear of the timer as far forward toward the

panel as possible. Wire the P3Gjj socket, then push it

onto the rear of the timer. Then tighten the two retaining

screws. To release the adapter, lift the tab at the rear of the

adapter.

Several timers may be panel mounted close

together using Y92F-30 adapter as shown

here. When mounting two or more timers in a

vertical line, arrange the adapters so that their

molded tabs are positioned on the right and

left sides. When mounting two or more timers

in a horizontal line, arrange the adapters so

that their molded tabs are positioned on the

top and bottom sides.

Molded

tab

Molded

tab

Panel cutout for side-by-side

mounting of two timers

JTRACK MOUNTING

Using P2CF-j

jSocket

The P2CF-jj socket has two hooks that

secure the timer to the socket. Be sure to

allow at least 20 mm (0.79 in) clearance

above and below the socket to gain access

and to release the hooks for servicing and

maintenance. Insert timer into the socket.

Latch hooks. Then clip rear of the socket to

the track. Push the bottom onto the track until

the latch hooks securely.

Removal

Pull the latch on the socket with a flat-blade

screwdriver and remove the timer and socket

as one unit.

Mounting

Hook 20 mm

(0.79 in)

P2CF-11

or P2CF-08

socket

H3CR-AH3CR-A

Precautions

JOPERATING ENVIRONMENT

Do not use the Timer in the following locations.

DLocations with radical temperature changes.

DLocations with high humidity that may result in

condensation.

DLocations with excessive vibration or shock.

DLocations with corrosive gas or dust.

DLocations where the Timer is exposed to sprayed water, oil,

or chemicals.

Organic solvents (such as paint thinner) as well as strong acid or

alkali solutions will damage the outer casing of the Timer.

If the Timer is used in an area with excessive electrical noise, be

sure to separate the Timer, wires, and input device as far as

possible from the noise sources. Shield the input signal wiring to

prevent electrical interference.

JVOLTAGE WITHSTAND TEST

If the Timer is mounted to a control board, remove the Timer from

the control board or short-circuit the control board circuitry before

carrying out a voltage withstand test between the electric circuitry

and non-charged metal part of the Timer. This protects the

internal circuitry of the Timer from damage.

JPRECAUTIONS FOR EN (VDE)

CONFORMANCE

The H3CR-A Series, installed as a built-in timer, conforms to

EN61812-1 (VDE0435/P2021) provided that the following

conditions are satisfied.

Make sure that no voltage is applied to any terminals before

removing the Timer from the Socket.

The output section of the H3CR-A is provided only with basic

isolation. Provide supplementary basic isolation on the load side

connected to the output so that reinforced isolation required by

the EN (VDE) standards will be ensured.

The H3CR-A itself is designed under the following conditions:

DOvervoltage category III

DPollution degree 2

DIsolation

Operation parts: Reinforced isolation

With clearance of 5.5 mm and creepage distance of 5.5 mm

at 230 VAC

Output: Basic isolation (See Note.)

With clearance of 3 mm and creepage distance of 3 mm at

230 VAC

Note: The 11-pin model ensures basic isolation by itself and also

ensures basic isolation with the 11-pin model mounted to

the OMRON P2CF-11 or P3GA-11 Socket.

Connect the two output contacts different in polarity to the loads

so that they will be the same in potential.

C at . N o. G C T MC N 1 3/ 02 S pec if ic at ions s ubjec t t o c hange w it hout not ic e. P r int ed in U . S . A .

OMRON ELECTRONICS LLC

OneEastCommerceDrive

Schaumburg, IL 60173

NOTE: DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters to inches divide by 25.4.

1-800-55-OMRON

OMRON CANADA, INC.

885 Milner Avenue

Scarborough, Ontario M1B 5V8

416-286-6465

OMRON ON--LINE

Global -- http://www.omron.com

USA -- http://www.omron.com/oei

Canada -- http://www.omron.com/oci