AP7363 1.5A LOW QUIESCENT CURRENT, FAST TRANSIENT ULTRA-LOW DROPOUT LINEAR REGULATOR Description Pin Assignments The AP7363 is a 1.5A adjustable output voltage linear regulator with (Top View) ultra-low dropout. The device includes pass element, error amplifier, band-gap, current limit and thermal shutdown circuitry. ADJ/ NC OUT OUT OUT 8 7 6 5 1 2 3 4 GND IN IN IN The characteristics of low dropout voltage and fast transient response to step changes in load make it suitable for low voltage microprocessor applications. The typical quiescent current is approximately 0.5mA and changes little with load current. The built-in current-limit and thermal-shutdown functions prevent IC from damage in fault conditions. This device is available in U-DFN2030-8, SO-8EP, SOT223 and TO252 packages. U-DFN2030-8 (Top View) Features * 1.5A ultra-low dropout linear regulator * Ultra-low dropout: 190mV at 1.5A * Stable with 10F input/output capacitor, any types * Wide input voltage range: 2.2V to 5.5V * Adjustable output voltage: 0.6V to 5.0V * Fixed output options: 1V, 1.2V, 1.5V, 1.8V, 2.5V, 3.3V * Low ground pin current * 25nA quiescent current in shutdown mode * VADJ accuracy of 1.5% @ +25C * VADJ accuracy of 3% over line, load and temperature * Excellent Load/Line Transient Response * Current limit and thermal shutdown protection * Ambient temperature range: -40C to +85C * * * 1 8 ADJ/NC IN 2 7 OUT IN 3 6 OUT IN 4 5 OUT SO-8EP (Top View) 3 OUT U-DFN2030-8, SO-8EP, SOT223 and TO252: Available in "Green" Molding Compound (No Br, Sb) 2 GND (TAB) Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2) Halogen and Antimony Free. "Green" Device (Note 3) 1 IN SOT223 (Fixed Output) Applications * GND ASIC power supplies in printers, graphics cards, DVD players, STBs, routers, etc * FPGA and DSP core or I/O power supplies * SMPS regulator * Conversion from 3.3V or 5V rail (Top View) 3 2 GND 1 TO252 Notes: 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant. 2. See http://www.diodes.com for more information about Diodes Incorporated's definitions of Halogen- and Antimony-free, "Green" and Lead-free. 3. Halogen- and Antimony-free "Green" products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and <1000ppm antimony compounds. AP7363 Document number: DS35059 Rev. 8 - 2 1 of 14 www.diodes.com December 2012 (c) Diodes Incorporated AP7363 Typical Applications Circuit VIN VOUT IN VIN VOUT OUT IN AP7363 OUT AP7363 10F 10F R1 10F 10F ADJ GND GND R2 Fixed Output Adjustable Output R VOUT = VREF1+ 1 where R2 10k R2 Pin Descriptions Pin Number Pin Name GND IN OUT SOT223 TO252 2 1 3 U-DFN2030-8 SO-8EP 1 2, 3, 4 5, 6, 7 ADJ NA 8 NC NA 8 EP/TAB -- -- Function Ground. Voltage input pin. Voltage output pin. Output feedback pin for adjustable version only - a resistor divider from this pin to the OUT pin and ground sets the output voltage. No connection for fixed output version. The exposed pad (EP) is used to remove heat from the package and it is recommended that it is connected to a copper area. The die is electrically connected to the exposed pad. It is recommended to connect it externally to GND, but should not be the only ground connection. Functional Block Diagram IN OUT Gate Driver EN Current Limit and Thermal Shutdown OUT IN R EN Gate Driver Current Limit and Thermal Shutdown ADJ 0.605V 0.605V R GND Fixed Version AP7363 Document number: DS35059 Rev. 8 - 2 GND Adjustable Version 2 of 14 www.diodes.com December 2012 (c) Diodes Incorporated AP7363 Absolute Maximum Ratings (cont.) (@TA = +25C, unless otherwise specified.) Symbol ESD HBM ESD MM Parameter Human Body Model ESD Protection Machine Model ESD Protection Ratings 2000 200 Unit V V VIN Input Voltage -0.3 to +6.0 V VOUT OUT Voltage -0.3 to VIN +0.3 V IOUT Continuous Load Current Internal Limited TST Storage Temperature Range TJ Maximum Junction Temperature -65 to +150 C 150 C Recommended Operating Conditions (@TA = +25C, unless otherwise specified.) Symbol Parameter VIN Input voltage IOUT Output Current Notes: Min Max Unit 2.2 5.5 V 0 1.5 A TA Operating Ambient Temperature -40 +85 C TJ Operating Junction Temperature (Note 5) -40 +125 C 4. Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated are not implied. Exposure to absolute-maximum rated conditions for extended periods may affect device reliability. 5. Operating junction temperature must be evaluated and derated as needed, based on ambient temperature (TA), power dissipation (PD), maximum allowable operating junction temperature (TJ-MAX), and package thermal resistance (JA). AP7363 Document number: DS35059 Rev. 8 - 2 3 of 14 www.diodes.com December 2012 (c) Diodes Incorporated AP7363 Electrical Characteristics (@TA = +25C, VIN = 3.3V, IOUT = 10mA, CIN = 10F, COUT = 10F, unless otherwise specified.) Minimum and maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TA = +25C, and are provided for reference purposes only. Symbol Parameter Test Conditions Min Typ Max Unit VADJ ADJ Pin Voltage VIN = VIN-MIN to VIN-MAX, IOUT = 10mA to 1.5A IADJ ADJ Pin Bias Current VIN = VIN-MIN to VIN-MAX Dropout Voltage (Note 6) IOUT = 1.5A, VOUT = 2.5V VDROPOUT VOUT /VIN Line Regulation (Note 7) VIN = VIN-MIN to VIN-MAX VOUT /IOUT Load Regulation (Note 7) IOUT = 10mA to 1.5A IGND IOUT-PK Ground Pin Current in Normal Operation Mode IOUT = 10mA to 1.5A Peak Output Current VOUT VOUT - NOM -5% TA = +25C 0.584 Over temp 0.575 nA 750 190 TA = +25C Over temp 240 mV 280 -- Over temp TA = +25C V 0.635 Over temp TA = +25C 0.626 50 TA = +25C 0.04 -- 0.05 -- 0.18 Over temp 0.33 TA = +25C 1.0 Over temp -- %/V %/A 1.2 mA 1.3 A 3.6 3.7 TA = +25C Short Circuit Current OUT grounded td(off) Turn-Off Delay From VEN < VIL to VOUT = OFF, IOUT = 1.5A td(on) Turn-On Delay ISC 0.605 Over temp A 2 25 s s From VEN > VIH to VOUT = ON, IOUT = 1.5A 25 VIN = 3.0V, IOUT = 1.5A, f = 120Hz 65 VIN = 3.0V, IOUT = 1.5A, f = 1kHz 61 Output Noise Density F = 120Hz, COUT = 10F ceramic 1.0 V/Hz Output Noise Voltage BW = 100Hz - 100kHz, COUT = 10F ceramic 100 V(rms) TSHDN Thermal Shutdown Threshold TJ rising 170 THYS Thermal Shutdown Hysteresis TJ falling from TSHDN 10 Thermal Resistance Junction-toAmbient U-DFN2030-8 (Note 8) SO-8EP (Note 8) SOT223 (Note 8) 174.0 52.8 105.7 TO252 (Note 8) U-DFN2030-8 (Note 8) SO-8EP (Note 8) SOT223 (Note 8) TO252 (Note8) 87.8 28.2 10.0 18.5 17.3 PSRR n(l/f) en JA JC Notes: Ripple Rejection Thermal Resistance Junction-to-Case dB C o C/W o C/W 6. Dropout voltage is the minimum voltage difference between the input and the output at which the output voltage drops 2% below its nominal value. For any output voltage less than 2.5V, the minimum VIN operating voltage is the limiting factor. 7. The line and load regulation specification contains only the typical number. However, the limits for line and load regulation are included in the adjust voltage tolerance specification. 8. Device mounted on 2" x 2" FR-4 substrate PCB, 2oz copper with minimum recommended pad layout. AP7363 Document number: DS35059 Rev. 8 - 2 4 of 14 www.diodes.com December 2012 (c) Diodes Incorporated AP7363 Typical Performance Characteristics (@TJ = +25C, VIN = 2.7V, CIN = 10F, COUT = 10F, IOUT = 10mA, VOUT = 1.8V.) 10k 10k COUT = 10F CER COUT = 10F NOISE (nV/Hz) NOISE (nV/Hz) 1k 100 10 100 1000 10k FREQUENCY (Hz) Noise Density 1k 100 10 100 100k 1000 10k FREQUENCY (Hz) Noise Density 100k 2 3 2.5 VOUT (V) IGND (mA) 2 1.5 1 25C 125C 1 -40C 0.5 0 0 0.5 1 0 1.5 0 ILOAD (A) IGND vs. Load Current 0.615 2 VIN (V) Turn-On Characteristics 3 0.3 DROPOUT VOLTAGE (V) 0.610 VADJ (V) 1 0.605 0.600 125C 0.2 25C -40C 0.1 0.595 0.590 -50 -25 0 25 50 75 100 125 Document number: DS35059 Rev. 8 - 2 0.5 1 1.5 LOAD CURRENT (A) Dropout Voltage vs. Load Current TEMPERATURE (C) VADJ vs. Temperature AP7363 0 0 5 of 14 www.diodes.com December 2012 (c) Diodes Incorporated AP7363 Typical Performance Characteristics (cont.) (@TJ = +25C, VIN = 2.7V, CIN = 10F, COUT = 10F, IOUT = 10mA, VOUT = 1.8V.) Turn-On Time Turn-On Time VOUT = 1.2V (500mV/div) IL = 1.5A, COUT = 10F CER VOUT = 1.2V (500mV/div) IL = 0A, COUT = 10F CER VIN = 3.0V (2V/div) VIN = 3.0V (2V/div) Time (10s/div) Time (10s/div) Load Transient Response 90 VIN = 3.3V COUT =10F CER VOUT = 1.8V (50mV/div) REJECTION RATIO (dB) 80 70 60 50 40 30 20 10 ILOAD = 100mA to 1.5A (1A/div) VIN = 3.3V VOUT = 1.8V IOUT = 1A C IN = 1F CER C OUT = 1F CER 0 100 1k 10k 100k FREQUENCY (kHz) PSRR 1M Time (40s/div) AP7363 Document number: DS35059 Rev. 8 - 2 6 of 14 www.diodes.com December 2012 (c) Diodes Incorporated AP7363 Application Note Input Capacitor A minimum 2.2F ceramic capacitor is recommended between IN and GND pins to decouple input power supply glitch and noise. The amount of the capacitance may be increased without limit. Larger input capacitor like 10F will provide better load transient response. This input capacitor must be located as close as possible to the device to assure input stability and reduce noise. For PCB layout, a wide copper trace is required for both IN and GND pins. A lower ESR capacitor type allows the use of less capacitance, while higher ESR type requires more capacitance. Output Capacitor The output capacitor is required to stabilize and help the transient response of the LDO. The AP7363 is stable with any type of capacitor, with no limitations on minimum or maximum ESR. The device is designed to have excellent transient response for most applications with a small amount of output capacitance. The device is also stable with multiple capacitors in parallel, which can be of any type of value. Additional capacitance helps to reduce undershoot and overshoot during transient loads. This capacitor should be placed as close as possible to OUT and GND pins for optimum performance. Adjustable Operation The AP7363 provides output voltage from 0.6V to 5.0V through external resistor divider as shown below. The output voltage is calculated by: R VOUT = VREF 1 + 1 R 2 Where VREF = 0.6V (the internal reference voltage) Rearranging the equation will give the following that is used for adjusting the output to a particular voltage: V R1 = R 2 OUT - 1 V REF To maintain the stability of the internal reference voltage, R2 need to be kept smaller than 10k. No Load Stability Other than external resistor divider, no minimum load is required to keep the device stable. The device will remain stable and regulated in no load condition. AP7363 Document number: DS35059 Rev. 8 - 2 7 of 14 www.diodes.com December 2012 (c) Diodes Incorporated AP7363 Application Note (cont.) Stability and Phase Margin Any regulator which operates using a feedback loop must be compensated in such a way as to ensure adequate phase margin, which is defined as the difference between the phase shift and -180 degrees at the frequency where the loop gain crosses unity (0 dB). For most LDO regulators, the ESR of the output capacitor is required to create a zero to add enough phase lead to ensure stable operation. The AP7363 has a internal compensation circuit which maintains phase margin regardless of the ESR of the output capacitor, any type of capacitos can be used. The two charts on the next page show the gain/phase plot of the AP7363 with an output of 1.2V, 10F ceramic output capacitor, delivering 1.5A load current and no load. It can be seen the phase margin is about 90 (which is very stable). LOOP GAIN (dB) 60 GAIN 40 120 120 100 100 80 80 60 60 20 40 0 20 -20 0 -40 -60 -80 -100 -20 VIN = 2.7V VOUT = 1.2V IL = 1.5A COUT = 10F CER -120 100 1k 10k 100k 40 120 PHASE 100 80 GAIN 60 20 40 0 20 -20 0 -40 -60 -40 -80 -60 -100 -80 1M 140 -120 100 -20 VIN = 2.7V VOUT = 1.2V I L = 0A COUT = 10F CER 1k PHASE MARGIN () 80 140 LOOP GAIN (dB) 100 PHASE PHASE MARGIN () 120 -40 -60 10k 100k -80 1M FREQUENCY(Hz) Gain-Bandwidth Plot for no Load FREQUENCY(Hz) Gain-Bandwidth Plot for 1.5A Load Short Circuit Protection When output current at OUT pin is higher than current limit threshold, the current limit protection will be triggered and clamp the output current to prevent over-current and to protect the regulator from damage due to overheating. Thermal Shutdown Protection Thermal protection disables the output when the junction temperature rises to approximately +170C, allowing the device to cool down. When the junction temperature reduces to approximately +160C the output circuitry is enabled again. Depending on power dissipation, thermal resistance, and ambient temperature, the thermal protection circuit may cycle on and off. This cycling limits the heat dissipation of the regulator, protecting it from damage due to overheating. Low Quiescent Current The AP7363, consuming only around 0.5mA for all input range, provides great power saving in portable and low power applications. Output Noise This is the integrated value of the output noise over a specified frequency range. Input voltage and output load current are kept constant during the measurement. Results are expressed in Vrms or VHz. The AP7363 is a low noise regulator and needs no external noise reduction capacitor. Output voltage noise is typically 100Vrms overall noise level between 100 Hz and 100 kHz. Noise is specified in two ways: Output noise density is the RMS sum of all noise sources, measured at the regulator output, at a specific frequency (measured with a 1Hz bandwidth). This type of noise is usually plotted on a curve as a function of frequency. Output noise voltage is the RMS sum of spot noise over a specified bandwidth. Spot noise is measured in units V/Hz or nV/Hz and total output noise is measured in V(rms). The primary source of noise in low-dropout regulators is the internal reference. AP7363 Document number: DS35059 Rev. 8 - 2 8 of 14 www.diodes.com December 2012 (c) Diodes Incorporated AP7363 Application Note (cont.) Power Dissipation The device power dissipation and proper sizing of the thermal plane that is connected to the thermal pad is critical to avoid thermal shutdown and ensure reliable operation. Power dissipation of the device depends on input voltage and load conditions and can be calculated by: PD = (VIN - VOUT) X IOUT The maximum power dissipation, handled by the device, depends on the junction to ambient thermal resistance, and maximum ambient temperature, which can be calculated by the equation in the following: PD _ max = ( +150C - TA ) R JA Ordering Information Part Number Package Code Packaging (Note 9) AP7363-XXHA-7 AP7363-XXSP-13 AP7363-XXE-13 AP7363-XXD-13 HA SP E D U-DFN2030-8 SO-8EP SOT223-3L TO252-3L Note: 7"/13" Tape and Reel Quantity Part Number Suffix 3000/Tape & Reel -7 2500/Tape & Reel -13 2500/Tape & Reel -13 2500/Tape & Reel -13 9. TO252 and SOT223 are only available with fixed output version. Marking Information (1) U-DFN2030-8 Device AP7363ADJ AP7363-10 AP7363-12 AP7363-15 AP7363-18 AP7363-25 AP7363-33 AP7363 Document number: DS35059 Rev. 8 - 2 Package U-DFN2030-8 U-DFN2030-8 U-DFN2030-8 U-DFN2030-8 U-DFN2030-8 U-DFN2030-8 U-DFN2030-8 9 of 14 www.diodes.com Identification Code SA SB SC SD SE SF SG December 2012 (c) Diodes Incorporated AP7363 Marking Information (cont.) (2) SO-8EP (3) SOT223 (4) TO252 AP7363 Document number: DS35059 Rev. 8 - 2 10 of 14 www.diodes.com December 2012 (c) Diodes Incorporated AP7363 Package Outline Dimensions (All dimensions in mm.) Please see AP02002 at http://www.diodes.com/datasheets/ap02002.pdf for latest version. (1) U-DFN2030-8 A A1 A3 U-DFN2030-8 Dim Min Max Typ A 0.57 0.63 0.60 A1 0 0.05 0.02 A3 0.15 b 0.20 0.30 0.25 D 1.95 2.05 2.00 D2 1.40 1.60 1.50 e 0.50 E 2.95 3.05 3.00 E2 1.50 1.70 1.60 L 0.35 0.45 0.40 Z 0.125 All Dimensions in mm Seating Plane D L e (Pin #1 ID) C'0.25*45 E E2 D2 Z b (2) SO-8EP Exposed Pad 8 5 E1 1 H 4 F b Bottom View E 9 (All sides) N 7 A e D A1 AP7363 Document number: DS35059 Rev. 8 - 2 45 Q C 4 3 Gauge Plane Seating Plane E0 SO-8EP (SOP-8L-EP) Dim Min Max Typ A 1.40 1.50 1.45 A1 0.00 0.13 b 0.30 0.50 0.40 C 0.15 0.25 0.20 D 4.85 4.95 4.90 E 3.80 3.90 3.85 E0 3.85 3.95 3.90 E1 5.90 6.10 6.00 e 1.27 F 2.75 3.35 3.05 H 2.11 2.71 2.41 L 0.62 0.82 0.72 N 0.35 Q 0.60 0.70 0.65 All Dimensions in mm L 11 of 14 www.diodes.com December 2012 (c) Diodes Incorporated AP7363 Package Outline Dimensions (cont.) (All dimensions in mm.) Please see AP02002 at http://www.diodes.com/datasheets/ap02002.pdf for latest version. (3) SOT223 SOT223 Dim Min Max Typ A 1.55 1.65 1.60 A1 0.010 0.15 0.05 b1 2.90 3.10 3.00 b2 0.60 0.80 0.70 C 0.20 0.30 0.25 D 6.45 6.55 6.50 E 3.45 3.55 3.50 E1 6.90 7.10 7.00 e -- -- 4.60 e1 -- -- 2.30 L 0.85 1.05 0.95 Q 0.84 0.94 0.89 All Dimensions in mm A A1 (4) TO252 E A b3 c2 L3 A2 D E1 H L4 A1 L e 2X b2 3X b AP7363 Document number: DS35059 Rev. 8 - 2 a 12 of 14 www.diodes.com TO252 Dim Min Max Typ A 2.19 2.39 2.29 A1 0.00 0.13 0.08 A2 0.97 1.17 1.07 b 0.64 0.88 0.783 b2 0.76 1.14 0.95 b3 5.21 5.46 5.33 c2 0.45 0.58 0.531 D 6.00 6.20 6.10 D1 5.21 - - e 2.286 - - E 6.45 6.70 6.58 E1 4.32 - - H 9.40 10.41 9.91 L 1.40 1.78 1.59 L3 0.88 1.27 1.08 L4 0.64 1.02 0.83 a 0 10 - All Dimensions in mm December 2012 (c) Diodes Incorporated AP7363 Suggested Pad Layout Please see AP02001 at http://www.diodes.com/datasheets/ap02001.pdf for the latest version. (1) U-DFN2030-8 X2 Y C Dimensions Y2 C G X X1 X2 Y Y1 Y2 Y1 X1 Value (in mm) 0.500 0.250 0.350 1.500 1.850 0.600 1.600 3.300 G Pin1 X (2) SO-8EP X2 Dimensions C X X1 X2 Y Y1 Y2 Y1 Y2 X1 Value (in mm) 1.270 0.802 3.502 4.612 1.505 2.613 6.500 Y C X (3) SOT223 X1 Y1 Dimensions X1 X2 Y1 Y2 C1 C2 C1 Y2 Value (in mm) 3.3 1.2 1.6 1.6 6.4 2.3 C2 X2 (4) TO252 X2 Dimensions Z X1 X2 Y1 Y2 C E1 Y2 C Z Value (in mm) 11.6 1.5 7.0 2.5 7.0 6.9 2.3 Y1 X1 AP7363 Document number: DS35059 Rev. 8 - 2 E1 13 of 14 www.diodes.com December 2012 (c) Diodes Incorporated AP7363 IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes Incorporated. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright (c) 2012, Diodes Incorporated www.diodes.com AP7363 Document number: DS35059 Rev. 8 - 2 14 of 14 www.diodes.com December 2012 (c) Diodes Incorporated