SN74GTLPH1645 16-BIT LVTTL-TO-GTLP ADJUSTABLE-EDGE-RATE BUS TRANSCEIVER SCES290A - OCTOBER 1999 - REVISED JANUARY 2001 D D D D D D D D D D DGG OR DGV PACKAGE (TOP VIEW) Member of Texas Instruments' Widebus Family TI-OPC Circuitry Limits Ringing on Unevenly Loaded Backplanes OEC Circuitry Improves Signal Integrity and Reduces Electromagnetic Interference Bidirectional Interface Between GTLP Signal Levels and LVTTL Logic Levels LVTTL Interfaces Are 5-V Tolerant High-Drive GTLP Outputs (100 mA) LVTTL Outputs (-24 mA/24 mA) Variable Edge-Rate Control (ERC) Input Selects GTLP Rise and Fall Times for Optimal Data-Transfer Rate and Signal Integrity in Distributed Loads Ioff, Power-Up 3-State, and BIAS VCC Support Live Insertion Bus Hold on A-Port Data Inputs Distributed VCC and GND Pins Minimize High-Speed Switching Noise 1DIR 1A1 1A2 GND 1A3 1A4 VCC GND 1A5 1A6 GND 1A7 1A8 GND ERC 2A1 2A2 GND 2A3 2A4 GND VCC 2A5 2A6 GND 2A7 2A8 2DIR description 1 56 2 55 3 54 4 53 5 52 6 51 7 50 8 49 9 48 10 47 11 46 12 45 13 44 14 43 15 42 16 41 17 40 18 39 19 38 20 37 21 36 22 35 1OE 1B1 1B2 GND 1B3 1B4 VCC GND 1B5 1B6 GND 1B7 1B8 BIAS VCC VREF 2B1 2B2 GND 2B3 2B4 GND VCC 2B5 2B6 GND 2B7 2B8 2OE The SN74GTLPH1645 is a high-drive, 16-bit bus 23 34 transceiver that provides LVTTL-to-GTLP and 24 33 GTLP-to-LVTTL signal-level translation. It is 25 32 partitioned as two 8-bit transceivers. The device 26 31 provides a high-speed interface between cards 27 30 operating at LVTTL logic levels and a backplane 28 29 operating at GTLP signal levels. High-speed (about three times faster than standard LVTTL or TTL) backplane operation is a direct result of GTLP's reduced output swing (<1 V), reduced input threshold levels, improved differential input, OEC circuitry, and TI-OPC circuitry. Improved GTLP OEC and TI-OPC circuits minimize bus-settling time and have been designed and tested using several backplane models. The high drive allows incident-wave switching in heavily loaded backplanes with equivalent load impedance down to 11 . GTLP is the Texas Instruments (TI) derivative of the Gunning Transceiver Logic (GTL) JEDEC standard JESD 8-3. The ac specification of the SN74GTLPH1645 is given only at the preferred higher noise-margin GTLP, but the user has the flexibility of using this device at either GTL (VTT = 1.2 V and VREF = 0.8 V) or GTLP (VTT = 1.5 V and VREF = 1 V) signal levels. Normally, the B port operates at GTLP signal levels. The A-port and control inputs operate at LVTTL logic levels but are 5-V tolerant and are compatible with TTL and 5-V CMOS inputs. VREF is the B-port differential input reference voltage. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. OEC, TI, TI-OPC, and Widebus are trademarks of Texas Instruments. Copyright 2001, Texas Instruments Incorporated PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 PRODUCT PREVIEW D SN74GTLPH1645 16-BIT LVTTL-TO-GTLP ADJUSTABLE-EDGE-RATE BUS TRANSCEIVER SCES290A - OCTOBER 1999 - REVISED JANUARY 2001 description (continued) This device is fully specified for live-insertion applications using Ioff, power-up 3-state, and BIAS VCC. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. The power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down, which prevents driver conflict. The BIAS VCC circuitry precharges and preconditions the B-port input/output connections, preventing disturbance of active data on the backplane during card insertion or removal, and permits true live-insertion capability. This GTLP device features TI-OPC circuitry, which actively limits the overshoot caused by improperly terminated backplanes, unevenly distributed cards, or empty slots during low-to-high signal transitions. This, improves signal integrity, which allows adequate noise margin to be maintained at higher frequencies. High-drive GTLP backplane interface devices feature adjustable edge-rate control (ERC). Changing the ERC input voltage between GND and VCC adjusts the B-port output rise and fall times. This allows the designer to optimize system data-transfer rate and signal integrity to the backplane load. Active bus-hold circuitry holds unused or undriven LVTTL data inputs at a valid logic state. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended. PRODUCT PREVIEW When VCC is between 0 and 1.5 V, the device is in the high-impedance state during power up or power down. However, to ensure the high-impedance state above 1.5 V, the output-enable (OE) input should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. GQL PACKAGE (TOP VIEW) 1 2 3 4 5 terminal assignments 6 1 2 3 4 5 6 A A 1A2 1A1 1DIR 1OE 1B1 1B2 B B 1A4 1A3 GND GND 1B3 1B4 C 1A5 GND 1B5 1A7 1A6 VCC GND GND D VCC GND 1B6 1B7 E GND 1A8 1B8 BIAS VCC F ERC 2A1 2B1 G 2A2 2A3 GND GND 2B3 VREF 2B2 H 2A4 GND 2B4 J 2A5 2A6 VCC GND GND H VCC GND 2B6 2B5 J K 2A7 2A8 2DIR 2OE 2B8 2B7 C D E F G K ORDERING INFORMATION TA -40C to 85C PACKAGE ORDERABLE PART NUMBER TOP-SIDE MARKING TSSOP - DGG Tape and reel SN74GTLPH1645DGGR GTLPH1645 TVSOP - DGV Tape and reel SN74GTLPH1645DGVR GL45 VFBGA - GQL Tape and reel SN74GTLPH1645GQLR GL45 Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN74GTLPH1645 16-BIT LVTTL-TO-GTLP ADJUSTABLE-EDGE-RATE BUS TRANSCEIVER SCES290A - OCTOBER 1999 - REVISED JANUARY 2001 functional description The SN74GTLPH1645 is a high-drive (100 mA), 16-bit bus transceiver partitioned as two 8-bit segments and is designed for asynchronous communication between data buses. The device transmits data from the A port to the B port or from the B port to the A port, depending on the logic level at the direction-control (DIR) input. OE can be used to disable the device so the buses are effectively isolated. Data polarity is noninverting. For A-to-B data flow, when OE is low and DIR is high, the B outputs take on the logic value of the A inputs. When OE is high, the outputs are in the high-impedance state. The data flow for B to A is similar to A to B, except OE and DIR are low. Function Tables OUTPUT CONTROL OUTPUT MODE X Z Isolation L B data to A port H A data to B port DIR H L L True transparent PRODUCT PREVIEW INPUTS OE B-PORT EDGE-RATE CONTROL (ERC) INPUT ERC LOGIC LEVEL NOMINAL VOLTAGE OUTPUT B-PORT EDGE RATE L GND Slow H VCC Fast POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 SN74GTLPH1645 16-BIT LVTTL-TO-GTLP ADJUSTABLE-EDGE-RATE BUS TRANSCEIVER SCES290A - OCTOBER 1999 - REVISED JANUARY 2001 logic diagram (positive logic) 1 1DIR 56 ERC 1A1 15 1OE 55 2 1B1 42 VREF To Seven Other Channels 28 PRODUCT PREVIEW 2DIR 29 2OE 2A1 41 16 2B1 To Seven Other Channels Pin numbers shown are for the DGG and DGV packages. 4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN74GTLPH1645 16-BIT LVTTL-TO-GTLP ADJUSTABLE-EDGE-RATE BUS TRANSCEIVER SCES290A - OCTOBER 1999 - REVISED JANUARY 2001 Supply voltage range, VCC and BIAS VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 4.6 V Input voltage range, VI (see Note 1): A port, ERC, and control inputs . . . . . . . . . . . . . . . . . . . . . -0.5 V to 7 V B port and VREF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 4.6 V Voltage range applied to any output in the high-impedance or power-off state, VO (see Note 1): A port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 7 V B port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 4.6 V Voltage range applied to any output in the high or low state, VO (see Note 1): A port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to VCC + 0.5 V B port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 4.6 V Current into any output in the low state, IO: A port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 mA B port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mA Current into any A port output in the high state, IO (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 mA Continuous current through each VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mA Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -50 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -50 mA Package thermal impedance, JA (see Note 3): DGG package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64C/W DGV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48C/W GQL package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. This current flows only when the output is in the high state and VO > VCC. 3. The package thermal impedance is calculated in accordance with JESD 51-7. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 PRODUCT PREVIEW absolute maximum ratings over operating free-air temperature range (unless otherwise noted) SN74GTLPH1645 16-BIT LVTTL-TO-GTLP ADJUSTABLE-EDGE-RATE BUS TRANSCEIVER SCES290A - OCTOBER 1999 - REVISED JANUARY 2001 recommended operating conditions (see Notes 4 through 7) VCC, BIAS VCC Supply voltage VTT Termination voltage VREF Supply voltage VI Input voltage VIH High-level input voltage MIN NOM MAX UNIT 3.15 3.3 3.45 V GTL 1.14 1.2 1.26 GTLP 1.35 1.5 1.65 GTL 0.74 0.8 0.87 GTLP 0.87 1 1.1 VCC VTT 5.5 V VCC 5.5 V B port Except B port B port ERC Except B port and ERC VREF+0.05 VCC-0.6 Low-level input voltage GND ERC PRODUCT PREVIEW Except B port and ERC IIK IOH Input clamp current IOL Low level output current Low-level t/v Input transition rise or fall rate t/VCC TA Power-up ramp rate High-level output current VREF-0.05 0.6 V 0.8 A port -18 mA -24 mA A port 24 B port 100 Outputs enabled 10 -40 mA ns/V s/V 20 Operating free-air temperature V 2 B port VIL V 85 C NOTES: 4. All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. 5. Proper connection sequence for use of the B-port I/O precharge feature is GND and BIAS VCC = 3.3 V first, I/O second, and VCC = 3.3 V last, because the BIAS VCC precharge circuitry is disabled when any VCC pin is connected. The control and VREF inputs can be connected anytime, but normally are connected during the I/O stage. If B-port precharge is not required, any connection sequence is acceptable, but generally, GND is connected first. 6. VTT and RTT can be adjusted to accommodate backplane impedances if the dc recommended IOL ratings are not exceeded. 7. VREF can be adjusted to optimize noise margins, but normally is two-thirds VTT. TI-OPC circuitry is enabled in the A-to-B direction and is activated when VTT > 0.7 V above VREF. If operated in the A-to-B direction, VREF should be set to within 0.6 V of VTT to minimize current drain. 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN74GTLPH1645 16-BIT LVTTL-TO-GTLP ADJUSTABLE-EDGE-RATE BUS TRANSCEIVER SCES290A - OCTOBER 1999 - REVISED JANUARY 2001 electrical characteristics over recommended operating free-air temperature range for GTLP (unless otherwise noted) VIK VOH A port TEST CONDITIONS VCC = 3.15 V, VCC = 3.15 V to 3.45 V, II = -18 mA IOH = -100 A VCC = 3 3.15 15 V IOH = -12 mA IOH = -24 mA VCC = 3.15 V to 3.45 V, A port VCC = 3 3.15 15 V VOL B port II Control inputs A port IOZH B port MIN VCC = 3.15 V VCC = 3.45 V, VCC = 3 3.45 45 V TYP MAX UNIT -1.2 V VCC-0.2 2.4 V 2 IOL = 100 A IOL = 12 mA 0.2 IOL = 24 mA IOL = 10 mA 0.5 0.4 0.2 IOL = 64 mA IOL = 100 mA 0.55 VI = 0 or 5.5 V 10 0.4 VO = VCC 10 VO = 1.5 V 10 IOZL IBHL A and B ports VCC = 3.45 V, VO = GND A port IBHH A port VCC = 3.15 V, VCC = 3.15 V, VI = 0.8 V VI = 2 V IBHLO# IBHHO|| A port VCC = 3.45 V, VCC = 3.45 V, VI = 0 to VCC VI = 0 to VCC 40 A or B port VCC = 3.45 V, IO = 0, VI (A or control input) = VCC or GND, VI (B port) = VTT or GND Outputs high ICC Outputs low 40 Outputs disabled 40 A port Ci Ciio -10 Control inputs A port VI = 3.15 V or 0 VO = 3.15 V or 0 B port VO = 1.5 V or 0 A A A A 75 A -75 VCC = 3.45 V, One A-port or control input at VCC - 0.6 V, Other A or control inputs at VCC or GND ICCk V 500 A -500 A 1.5 mA mA pF pF All typical values are at VCC = 3.3 V, TA = 25C. For I/O ports, the parameters IOZH and IOZL include the input leakage current. The bus-hold circuit can sink at least the minimum low sustaining current at VILmax. IBHL should be measured after lowering VIN to GND and then raising it to VILmax. The bus-hold circuit can source at least the minimum high sustaining current at VIHmin. IBHH should be measured after raising VIN to VCC and then lowering it to VIHmin. # An external driver must source at least IBHLO to switch this node from low to high. || An external driver must sink at least IBHHO to switch this node from high to low. k This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. hot-insertion specifications for A port over recommended operating free-air temperature range PARAMETER TEST CONDITIONS MIN MAX UNIT Ioff IOZPU VCC = 0, VCC = 0 to 1.5 V, BIAS VCC = 0, VI or VO = 0 to 5.5 V OE = 0 10 A VO = 0.5 V to 3 V, 30 A IOZPD VCC = 1.5 V to 0, VO = 0.5 V to 3 V, OE = 0 30 A POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 7 PRODUCT PREVIEW PARAMETER SN74GTLPH1645 16-BIT LVTTL-TO-GTLP ADJUSTABLE-EDGE-RATE BUS TRANSCEIVER SCES290A - OCTOBER 1999 - REVISED JANUARY 2001 live-insertion specifications for B port over recommended operating free-air temperature range PARAMETER TEST CONDITIONS BIAS VCC = 0, 30 A BIAS VCC = 0, VO = 0.5 V to 1.5 V, OE = 0 30 A BIAS VCC = 3 3.15 15 V to 3 3.45 45 V V, VO (B port) = 0 to 1.5 15V BIAS VCC = 3.3 V, IO = 0 VO (B port) = 0.6 V IOZPD VCC = 1.5 V to 0, VCC = 0 to 3.15 V VO IO VCC = 0, UNIT A BIAS VCC = 0, VCC = 3.15 V to 3.45 V VCC = 0, MAX 10 VCC = 0, VCC = 0 to 1.5 V, ICC (BIAS VCC) MIN VI or VO = 0 to 1.5 V VO = 0.5 V to 1.5 V, OE = 0 Ioff IOZPU BIAS VCC = 3.15 V to 3.45 V, 0.95 5 mA 10 A 1.05 V A -1 PRODUCT PREVIEW switching characteristics over recommended ranges of supply voltage and operating free-air temperature, VTT = 1.5 V and VREF = 1 V for GTLP (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) EDGE RATE tPLH tPHL A B Slow ns tPLH tPHL A B Fast ns ten tdis OE B Slow ns ten tdis OE B Fast ns tr time B outputs (20% to 80%) Rise time, tf Fall time, time B outputs (80% to 20%) tPLH tPHL ten tdis Fast Slow Fast TYP MAX UNIT ns ns B A -- ns OE A -- ns Slow (ERC = GND) and Fast (ERC = VCC) All typical values are at VCC = 3.3 V, TA = 25C. 8 Slow MIN POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN74GTLPH1645 16-BIT LVTTL-TO-GTLP ADJUSTABLE-EDGE-RATE BUS TRANSCEIVER SCES290A - OCTOBER 1999 - REVISED JANUARY 2001 PARAMETER MEASUREMENT INFORMATION 1.5 V 6V 500 From Output Under Test S1 Open GND CL = 50 pF (see Note A) TEST tPLH/tPHL tPLZ/tPZL tPHZ/tPZH 500 12.5 From Output Under Test CL = 30 pF (see Note A) S1 Open 6V GND LOAD CIRCUIT FOR A OUTPUTS Test Point LOAD CIRCUIT FOR B OUTPUTS 3V 1.5 V Input 1.5 V 0V tPLH tPHL VOH 1V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES (A port to B port) 1V 0V tPLH 1.5 V 1.5 V 0V Output Waveform 1 S1 at 6 V (see Note B) tPHL tPLZ 3V 1.5 V VOL + 0.3 V VOL tPHZ tPZH VOH Output 1.5 V tPZL 1.5 V 1V Input 3V Output Control 1.5 V VOL PRODUCT PREVIEW 1V Output Output Waveform 2 S1 at GND (see Note B) VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES (B port to A port) 1.5 V VOH VOH - 0.3 V 0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES (A port) NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 , tr 2 ns, tf 2 ns. D. The outputs are measured one at a time with one transition per measurement. Figure 1. Load Circuits and Voltage Waveforms POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 9 SN74GTLPH1645 16-BIT LVTTL-TO-GTLP ADJUSTABLE-EDGE-RATE BUS TRANSCEIVER SCES290A - OCTOBER 1999 - REVISED JANUARY 2001 DISTRIBUTED-LOAD BACKPLANE SWITCHING CHARACTERISTICS The preceding switching characteristics table shows the switching characteristics of the device into a lumped load (Figure 1). However, the designer's backplane application probably is a distributed load. The physical representation is shown in Figure 2. This backplane, or distributed load, can be approximated closely to a resistor inductance capacitance (RLC) circuit, as shown in Figure 3. This device has been designed for optimum performance in this RLC circuit. The following switching characteristics table shows the switching characteristics of the device into the RLC load, to help the designer better understand the performance of the GTLP device in this typical backplane. See www.ti.com/sc/gtlp for more information. 22 .25" Conn. 1" PRODUCT PREVIEW ZO = 50 1" Conn. 1" 1" Conn. .25" 22 1.5 V 1.5 V 1.5 V 11 Conn. 1" From Output Under Test 1" Rcvr Rcvr Rcvr Slot 2 Slot 19 Slot 20 LL = 14 nH Test Point CL = 18 pF Drvr Slot 1 Figure 3. High-Drive RLC Network Figure 2. High-Drive Test Backplane switching characteristics over recommended ranges of supply voltage and operating free-air temperature, VTT = 1.5 V and VREF = 1 V for GTLP (see Figure 3) PARAMETER FROM (INPUT) TO (OUTPUT) EDGE RATE tPLH tPHL A B Slow tPLH tPHL A B Fast ten tdis OE B Slow ten tdis OE B Fast tr Rise time, time B outputs (20% to 80%) tf time B outputs (80% to 20%) Fall time, Slow (ERC = GND) and Fast (ERC = VCC) All typical values are at VCC = 3.3 V, TA = 25C. All values are derived from TI-SPICE models. 10 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TYP 4.9 4.9 3.7 3.7 5.1 5.4 4.1 4.1 Slow 2 Fast 1.2 Slow 2.5 Fast 1.8 UNIT ns ns ns ns ns ns IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Customers are responsible for their applications using TI components. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such products or services might be or are used. TI's publication of information regarding any third party's products or services does not constitute TI's approval, license, warranty or endorsement thereof. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations and notices. Representation or reproduction of this information with alteration voids all warranties provided for an associated TI product or service, is an unfair and deceptive business practice, and TI is not responsible nor liable for any such use. Resale of TI's products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service, is an unfair and deceptive business practice, and TI is not responsible nor liable for any such use. Also see: Standard Terms and Conditions of Sale for Semiconductor Products. www.ti.com/sc/docs/stdterms.htm Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2001, Texas Instruments Incorporated