Features * Operating Voltage: 5V * Access Time: 30, 45 ns * Very Low Power Consumption * * * * * * * * - Active: 250 mW (Typ) - Standby: 1 W (Typ) - Data Retention: 0.5 W (Typ) Wide Temperature Range: -55C to +125C 400 Mils Width Package TTL Compatible inputs and Outputs Asynchronous Single 5V Supply Equal Cycle and Access Time Gated Inputs: - No Pull-up/down - Resistors Are Required QML Q and V with SMD 5962-89598 Rad. Tolerant 128K x 8 Very Low Power 5V CMOS SRAM Description The M65608E is a very low power CMOS static RAM organized as 131072 x 8 bits. Atmel brings the solution to applications where fast computing is as mandatory as low consumption, such as aerospace electronics, portable instruments, or embarked systems. M65608E Utilizing an array of six transistors (6T) memory cells, the M65608E combines an extremely low standby supply current (Typical value = 0.2 A) with a fast access time at 30 ns over the full military temperature range. The high stability of the 6T cell provides excellent protection against soft errors due to noise. The M65608E is processed according to the methods of the latest revision of the MIL STD 883 (class B or S), ESA SCC 9000 or QML. Rev. 4151G-AERO-06/02 1 Block Diagram Pin Configuration 2 32-lead DIL side-brazed 400 MILS 32-lead Flatpack 400 MILS M65608E 4151G-AERO-06/02 M65608E Pin Description Table 1. Pin Names Names Description A0 - A16 Address inputs I/O0 - I/O7 Data Input/Output CS1 Chip select 1 CS2 Chip select 2 WE Write Enable OE Output Enable VCC Power GND Ground Table 2. Truth Table Note: CS1 CS2 W OE Inputs/ Outputs H X X X Z Deselect/ Power-down X L X X Z Deselect/ power-down L H H L Data Out Read L H L X Data In Write L H H H Z Mode Output Disable L = low, H = high, X = H or L, Z = high impedance. 3 4151G-AERO-06/02 Electrical Characteristics Absolute Maximum Ratings Supply voltage to GND potential:..........................-0.5V + 7.0V *NOTE: Stresses greater than those listed under Absolute Maximum Ratings may cause permanent damage to the device.This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC input voltage: ..............................GND - 0.5V to VCC + 0.5 DC output voltage high Z state: ........GND - 0.5V to VCC + 0.5 Storage temperature: ..................................... -65C to +150C Output current into outputs (low): .................................. 20 mA Electro statics discharge voltage: ............................... > 2001V (MIL STD 883D method 3015.3) Military Operating Range Operating Voltage Operating Temperature 5V + 10% -55C to + 125C Recommended DC Operating Conditions Parameter Description Minimum Typical Maximum Unit VCC Supply voltage 4.5 5.0 5.5 V GND Ground 0.0 0.0 0.0 V VIL Input low voltage GND - 0.5 0.0 0.8 V VIH Input high voltage 2.2 - VCC + 0.5 V Minimum Typical Maximum Unit Capacitance Parameter Description Cin(1) Input low voltage - - 8 pF Cout(1) Output high voltage - - 8 pF Note: 4 1. Guaranteed but not tested. M65608E 4151G-AERO-06/02 M65608E DC Parameters DC Test Conditions Table 3. DC Test Conditions TA = -55C to + 125C; Vss = 0V; VCC = 4.5V to 5.5V Symbol Description Minimum Typical Maximum Unit IIX (1) Input leakage current -1 - 1 A IOZ(1) Output leakage current -1 - 1 A VOL (2) Output low voltage - - 0.4 V VOH (3) Output high voltage 2.4 - - V 1. GND < Vin < VCC, GND < Vout < VCC Output Disabled. 2. 3. VCC min. IOL = 8 mA. VCC min. IOH = -0.4 mA. Consumption Symbol Description 65608E-30 65608E-45 Unit Value ICCSB (1) Standby supply current 2 2 mA max ICCSB1 (2) Standby supply current 300 300 A max ICCOP (3) Dynamic operating current 130 100 mA max 1. 2. 3. CS1 > VIH or CS2 < VIL and CS1 < VIL. CS1 > VCC - 0.3V or, CS2 < GND + 0.3V and CS1 < 0.2V. F = 1/TAVAV, Iout = 0 mA, W = OE = VIH, Vin = GND or VCC, VCC max. 5 4151G-AERO-06/02 AC Parameters AC Test Conditions Input Pulse Levels: ....................................GND to 3.0V Input Rise/Fall Times: ...............................5 ns Input Timing Reference Levels: ................1.5V Output loading IOL/IOH (see Figure 1 and Figure 2)+30 pF AC Test Loads Waveforms Figure 1 Data Retention Mode Figure 2 Figure 3 Atmel CMOS RAM's are designed with battery backup in mind. Data retention voltage and supply current are guaranteed over temperature. The following rules ensure data retention: 1. During data retention chip select CS1 must be held high within VCC to VCC 0.2V or, chip select CS2 must be held down within GND to GND +0.2V. 2. Output Enable (OE) should be held high to keep the RAM outputs high impedance, minimizing power dissipation. 3. During power up and power-down transitions CS1 and OE must be kept between VCC + 0.3V and 70% of VCC, or with CS2 between GND and GND -0.3V. 4. The RAM can begin operation > TR ns after VCC reaches the minimum operation voltages (4.5V). Timing 6 M65608E 4151G-AERO-06/02 M65608E Data Retention Characteristics Parameter Description Minimum Typical TA = 25 C Maximum Unit VCCDR VCC for data retention 2.0 - - V TCDR Chip deselect to data retention time 0.0 - - ns TR Operation recovery time TAVAV(1) - - ns (2) Data retention current at 2.0V - 0.1 150 A (2) Data retention current at 3.0V - 0.2 200 A ICCDR1 ICCDR2 Notes: 1. TAVAV = Read Cycle Time 2. CS1 = VCC or CS2 = CS1 = GND, Vin = GND/VCC, this parameter is only tested at VCC = 2V. Write Cycle Symbol Parameter 65608-30 65608-45 Unit Value TAVAV Write cycle time 30 45 ns min TAVWL Address set-up time 0 0 ns min TAVWH Address valid to end of write 22 35 ns min TDVWH Data set-up time 18 20 ns min TE1LWH CS1 low to write end 22 35 ns min TE2HWH CS2 high to write end 22 35 ns min TWLQZ Write low to high Z(1) 8 15 ns max TWLWH Write pulse width 22 35 ns min TWHAX Address hold from to end of write 0 0 ns min TWHDX Data hold time 0 0 ns min TWHQX Write high to low Z(1) 0 0 ns min Note: 1. Parameters guaranteed, not tested, with output loading 5 pF. 7 4151G-AERO-06/02 Read Cycle Symbol Parameter 65608-30 65608-45 Unit Value TAVAV Read cycle time 30 45 ns min TAVQV Address access time 30 45 ns max TAVQX Address valid to low Z(1) 5 5 ns min TE1LQV Chip-select1 access time 30 45 ns max TE1LQX CS1 low to low Z(1) 3 3 ns min TE1HQZ CS1 high to high Z(1) 15 20 ns max TE2HQV Chip-select2 access time 30 45 ns max TE2HQX CS2 high to low Z(1) 3 3 ns min TE2LQZ CS2 low to high Z(1) 18 20 ns max TGLQV Output Enable access time 12 15 ns max TGLQX OE low to low Z(1) 0 0 ns min TGHQZ OE high to high Z(1) 8 15 ns max Note: 8 1. Parameters Guaranteed, not tested, with output loading 5 pF. M65608E 4151G-AERO-06/02 M65608E Write Cycle 1 WE Controlled, OE High During Write Write Cycle 2 WE Controlled, OE Low 9 4151G-AERO-06/02 Write Cycle 3 CS1 or CS2, Controlled Note: 10 The internal write time of the memory is defined by the overlap of CS1 Low and CS2 HIGH and W LOW. Both signals must be actived to initiate a write and either signal can terminate a write by going in actived. The data input setup and hold timing should be referenced to the actived edge of the signal that terminates the write. Data out is high impedance if OE = VIH. M65608E 4151G-AERO-06/02 M65608E Read Cycle 1 Read Cycle 2 Read Cycle 3 11 4151G-AERO-06/02 Ordering Information Part Number Temperature Range Speed Package Flow MMDJ-65608EV-30 -55 to +125C 30 ns FP32.4 Standard Mil MMDJ-65608EV-45 -55 to +125C 45 ns FP32.4 Standard Mil MMC9-65608EV-30 -55 to +125C 30 ns SB32.4 Standard Mil MMC9-65608EV-45 -55 to +125C 45 ns SB32.4 Standard Mil SMDJ-65608EV-30SB -55 to +125C 30 ns FP32.4 SCC B SMDJ-65608EV-45SB -55 to +125C 45 ns FP32.4 SCC B SMC9-65608EV-30SB -55 to +125C 30 ns SB32.4 SCC B SMC9-65608EV-45SB -55 to +125C 45 ns SB32.4 SCC B 5962-8959847QTC -55 to +125C 30 ns FP32.4 QML Q 5962-8959818MTC -55 to +125C 45 ns FP32.4 QML Q 5962-8959847QZC -55 to +125C 30 ns SB32.4 QML Q 5962-8959818MZC -55 to +125C 45 ns SB32.4 QML Q 5962-8959847VTC -55 to +125C 30 ns FP32.4 QML V 5962-8959818VTC -55 to +125C 45 ns FP32.4 QML V 5962-8959847VZC -55 to +125C 30 ns SB32.4 QML V 5962-8959818VZC -55 to +125C 45 ns SB32.4 QML V 25C 30 ns FP32.4 Engineering Samples 25C 30 ns SB32.4 Engineering Samples 25C 30 ns Die Engineering Samples 5962-895647Q6A -55 to +125C 30 ns Die QML Q 5962-895647V6A -55 to +125C 30 ns Die QML V MMDJ-65608EV-30-E MMC9-65608EV-30-E (1) MM0-65608EV-30-E Note: 12 1. Contact Atmel for availability. M65608E 4151G-AERO-06/02 M65608E Package Drawings 32-lead Flat Pack 400 Mils 13 4151G-AERO-06/02 M65608E Package Drawings 32-lead Side Braze 400 Mils 14 4151G-AERO-06/02 Atmel Headquarters Atmel Operations Corporate Headquarters Memory 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 487-2600 Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland TEL (41) 26-426-5555 FAX (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimhatsui East Kowloon Hong Kong TEL (852) 2721-9778 FAX (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan TEL (81) 3-3523-3551 FAX (81) 3-3523-7581 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 436-4314 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France TEL (33) 2-40-18-18-18 FAX (33) 2-40-18-19-60 ASIC/ASSP/Smart Cards Zone Industrielle 13106 Rousset Cedex, France TEL (33) 4-42-53-60-00 FAX (33) 4-42-53-60-01 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany TEL (49) 71-31-67-0 FAX (49) 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 1(719) 576-3300 FAX 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France TEL (33) 4-76-58-30-00 FAX (33) 4-76-58-34-80 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 1(719) 576-3300 FAX 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland TEL (44) 1355-803-000 FAX (44) 1355-242-743 e-mail literature@atmel.com Web Site http://www.atmel.com (c) Atmel Corporation 2002. Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company's standard warranty which is detailed in Atmel's Terms and Conditions located on the Company's web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel's products are not authorized for use as critical components in life support devices or systems. ATMEL (R) is a registered trademark of Atmel. Other terms and product names may be the trademarks of others. Printed on recycled paper. 4151G-AERO-06/02 /xM