TC4028BP/BF
2014-03-01
1
TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic
TC4028BP, TC4028BF
TC4028B BCD-to-Decimal Decoder
TC4028B is a BCD-to-DECIMAL decoder which converts BCD
signal into DECIMAL signal.
Of ten outputs from Q0 through Q9, one output corresponding
to input BCD code goes to the “H” level and all the others remain
at the “L” level.
When D is used as inhibit input by use of three input lines
from A to C, this decoder can be served as a BINARY-to-OCTAL
decoder.
Pin Assignment
TC4028BP
TC4028BF
Weight
DIP16-P-300-2.54A : 1.00 g (typ.)
SOP16-P-300-1.27A : 0.18 g (typ.)
Start of commercial production
1978-09
TC4028BP/BF
2014-03-01
2
Truth Table
Inputs Outputs
D C B A Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9
L L L L H L L L L L L L L L
L L L H L H L L L L L L L L
L L H L L L H L L L L L L L
L L H H L L L H L L L L L L
L H L L L L L L H L L L L L
L H L H L L L L L H L L L L
L H H L L L L L L L H L L L
L H H H L L L L L L L H L L
H L L L L L L L L L L L H L
H L L H L L L L L L L L L H
H L H L L L L L L L L L L L
H L H H L L L L L L L L L L
H H L L L L L L L L L L L L
H H L H L L L L L L L L L L
H H H L L L L L L L L L L L
H H H H L L L L L L L L L L
H = High level
L = Low level
Logic Diagram
TC4028BP/BF
2014-03-01
3
Absolute Maximum Ratings (Note)
Characteristics Symbol Rating Unit
DC supply voltage VDD V
SS 0.5 to VSS + 20 V
Input voltage VIN V
SS 0.5 to VDD + 0.5 V
Output voltage VOUT V
SS 0.5 to VDD + 0.5 V
DC input current IIN ±10 mA
Power dissipation PD 300 (DIP)/180 (SOP) mW
Operating temperature range Topr 40 to 85 °C
Storage temperature range Tstg 65 to 150 °C
Note: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or
even destruction.
Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly
even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute
maximum ratings and the operating ranges.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
Operating Ranges (VSS = 0 V) (Note)
Characteristics Symbol Test Condition Min Typ. Max Unit
DC supply voltage VDD 3 18 V
Input voltage VIN 0 V
DD V
Note: The operating ranges must be maintained to ensure the normal operation of the device.
Unused inputs must be tied to either VDD or VSS.
TC4028BP/BF
2014-03-01
4
Static Electrical Characteristics (VSS = 0 V)
Test Condition 40°C 25°C 85°C
Characteristics Sym-
bol VDD
(V) Min Max Min Typ. Max Min Max
Unit
High-level output
voltage VOH IOUT < 1 μA
VIN = VSS, VDD
5
10
15
4.95
9.95
14.95
4.95
9.95
14.95
5.00
10.00
15.00
4.95
9.95
14.95
V
Low-level output
voltage VOL IOUT < 1 μA
VIN = VSS, VDD
5
10
15
0.05
0.05
0.05
0.00
0.00
0.00
0.05
0.05
0.05
0.05
0.05
0.05
V
VOH = 4.6 V
VOH = 2.5 V
VOH = 9.5 V
VOH = 13.5 V
5
5
10
15
0.61
2.50
1.50
4.00
0.51
2.10
1.30
3.40
1.0
4.0
2.2
9.0
0.42
1.70
1.10
2.80
Output high current IOH
VIN = VSS, VDD
mA
VOL = 0.4 V
VOL = 0.5 V
VOL = 1.5 V
5
10
15
0.61
1.50
4.00
0.51
1.30
3.40
1.2
3.2
12.0
0.42
1.10
2.80
Output low current IOL
VIN = VSS, VDD
mA
VOUT = 0.5 V, 4.5 V
VOUT = 1.0 V, 9.0 V
VOUT = 1.5 V, 13.5 V
5
10
15
3.5
7.0
11.0
3.5
7.0
11.0
2.75
5.50
8.25
3.5
7.0
11.0
Input high voltage VIH
IOUT < 1 μA
V
VOUT = 0.5 V, 4.5 V
VOUT = 1.0 V, 9.0 V
VOUT = 1.5 V, 13.5 V
5
10
15
1.5
3.0
4.0
2.25
4.50
6.75
1.5
3.0
4.0
1.5
3.0
4.0
Input low voltage VIL
IOUT < 1 μA
V
“H” level IIH V
IH = 18 V 18 0.1 1050.1 1.0
Input
current “L” level IIL V
IL = 0 V 18 0.1 1050.1 1.0
μA
Quiescent supply
current IDD VIN = VSS, VDD
(Note)
5
10
15
5
10
20
0.005
0.010
0.015
5
10
20
150
300
600
μA
Note: All valid input combinations.
TC4028BP/BF
2014-03-01
5
Dynamic Electrical Characteristics (Ta = 25°C, VSS = 0 V, CL = 50 pF)
Test Condition
Characteristics Symbol
V
DD (V)
Min Typ. Max Unit
Output transition time
(low to high)
tTLH
5
10
15
70
35
30
200
100
80
ns
Output transition time
(high to low)
tTHL
5
10
15
70
35
30
200
100
80
ns
Propagation delay time
tpLH
tpHL
5
10
15
110
55
40
350
160
120
ns
Input capacitance CIN 5 7.5 pF
Waveform for Measurement of Dynamic Characteristics
TC4028BP/BF
2014-03-01
6
Package Dimensions
Weight: 1.00 g (typ.)
TC4028BP/BF
2014-03-01
7
Package Dimensions
Weight: 0.18 g (typ.)
TC4028BP/BF
2014-03-01
8
RESTRICTIONS ON PRODUCT USE
Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information
in this document, and related hardware, software and systems (collectively "Product") without notice.
This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with
TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission.
Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are
responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and
systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily
injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the
Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of
all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes
for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the
instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their
own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such
design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts,
diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating
parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR
APPLICATIONS.
PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE
EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH
MAY CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT
("UNINTENDED USE"). Except for specific applications as expressly stated in this document, Unintended Use includes, without
limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for
automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions,
safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. IF YOU USE
PRODUCT FOR UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT. For details, please contact your
TOSHIBA sales representative.
Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.
Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any
applicable laws or regulations.
The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any
infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to
any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.
ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY
WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR
LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND
LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO
SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
Do not use or otherwise make available Product or related software or technology for any military purposes, including without
limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile
technology products (mass destruction weapons). Product and related software and technology may be controlled under the
applicable export laws and regulations including, without limitation, the Japanese Foreign Exchange and Foreign Trade Law and the
U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited
except in compliance with all applicable export laws and regulations.
Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product.
Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances,
including without limitation, the EU RoHS Directive. TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES
OCCURRING AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS.