MB90427G/GA - Fujitsu Quantum Devices Limited

CAN BUS MICROCONTROLLER SOLUTIONS

INCLUDING INTEGRATED SINGLE VOLTAGE

FLASH MEMORY

PRODUCT OVERVIEW

CAN BUS

MICROCONTROLLERS

CAN BUS MICROCONTROLLERS

Controller Area Network (CAN) – Registered Trademark

of Robert Bosch GmbH

Embedded Algorithm™ – Trademark of Advanced Micro Devices

Windows – Registered Trademark of Microsoft Corp.

All Trademarks acknowledged

The information contained in this document has been carefully checked and is believed to be entirely

reliable. However Fujitsu and its subsidiaries assume no responsibility for inaccuracies.

The information contained in this document does not convey any licence under the copyrights, patent

rights or trademarks claimed and owned by Fujitsu. Fujitsu Limited and its subsidiaries reserve the

right to change products or specifications without notice.

No part of this publication may be copied or reproduced in any form or by any means or transferred

to any third party without the prior consent of Fujitsu.

Designed and produced in the UK. Printed on environmentally friendly paper.

Introduction to CAN Bus Controllers 2

Introduction to Flash ROM Microcontrollers 2

F2MC-16LX CPU-Core Architecture 3

F2MC-16LX Device Features 4

16 bit CAN MCU Roadmap 5

MB90425G/GA Series – 16 bit Single CAN with Stepper Motor & LCD Controller 6

MB90495G Series – Low Cost 16 bit Single CAN 7

MB90545G Series – 16 bit Single CAN, General Purpose 8

MB90595G Series – 16 bit Single CAN with Stepper Motor Controllers 9

MB90590 Series – 16 bit Double CAN with Stepper Motor Controllers 10

MB90540G Series – 16 bit Double CAN, General Purpose 11

MB90440G Series – 16 bit Triple CAN, General Purpose 12

FR Series – 32 bit RISC Architecture 13

FR+CAN Bus with Building Block Concept 14

MB91360 Series – FR 32 bit RISC Microcontrollers with three CAN Interfaces 15

MB91360 Series Block Diagram 16

REALOS Real-Time OS for 16 bit Families 17

REALOS Real-Time OS for the FR Series 17

OSEK/VDX Operating System 17

Euros 18

Flash/CAN 64 Evaluation Board 19

Flash/CAN 100 Evaluation Board 20

DevKit16 – Multi-Function Modular Starterkit 21

Starterkit MB91360 22

European Microcontroller Design Centre 23

Representatives and Distributors 24-25

Sales Offices Back Cover

CONTENTS

CAN BUS MICROCONTROLLERS

FLASH ROM Microcontrollers

All of the CAN MCUs are supported

by at least one version with FLASH

ROM as the user programmable

memory. This is the same technology

as the standard Fujitsu Flash

memories.

Features

●Available block sizes 64kB, 128kB,

256kB, 384kB and 512kB

●Blocks divided into separately

erasable and protectable sectors

●Supports programming by

Embedded Algorithm™

●No second programming voltage

required

●10,000 minimum erase cycles

guaranteed – 100,000 under

specification

●10 year data retention

●Programming can be by three

methods:

•On ordinary programmer with

adapter as with traditional OTP

devices

•Using Fujitsu embedded serial

programming mode via on-chip

UART directly to the FLASH

ROM

•Copying or downloading to

FLASH using customers’ own

bootstrap software

●Flash programming via CAN

supported

CAN Bus Controllers

Fujitsu has F2MC-16LX and FR devices

available that have full featured CAN

Bus protocol controllers as on-chip

peripherals for Automotive and

Industrial applications.

Features

●CAN 2.0A and 2.0B protocol

controller

●16 message buffers (8 for

MB90495 series), each

individually programmable for:

•Transmit or receive

•11 or 29 identifier bits

•Full identifier bit compare /

full mask / compare against

1 of 2 mask registers

●Ability to group buffers into

flexible multi-level configuration

●Readable error counter

Additional Features

●G-CAN devices (G in part number)

- these products allow a more

flexible setting of CAN bit rates

INTRODUCTION TO CAN BUS CONTROLLERS &

FLASH ROM MICROCONTROLLERS

Dedicated Registers

AH Accumulator

User Stack Pointer

System Stack Pointer

Processor Status

Program Counter

ADB Additional Data Bank Register

System Stack Bank RegisterSSB

User Stack Bank RegisterUSB

Data Bank RegisterDTB

Program Bank RegisterPCB

Direct Page RegisterDPR

USP

SSP

32 bit 16 bit

8 bit

General-Purpose Registers

Upper Addresses

(RL3)

(RL2)

(RL1)

(RL0)

Lower Addresses

R7 R6 (RW7)

R5 R4 (RW6)

R3 R2 (RW5)

R1 R0 (RW4)

RW3

RW2

RW1

RW0

16 bit

000180H+(RPx10H)

Max.32

Fujitsu’s 16 bit CPU core features

easy programming with plenty of

data types such as bit, nibble, byte,

word and long word together with

23 addressing modes. The memory

address range of 16MB is accessible

using bank or linear addressing

modes fully supported by the

optimised instruction set.

On-chip registers such as USER-

and SYSTEM stack pointers, together

with its supporting instructions,

provide additional advanced support

to Real-Time Operating Systems.

An extremely high I/O throughput

is achieved via the integrated

DMA-like EI2OS (Extended Intelligent

I/O Service). This, combined with the

improved pipeline processing using a

4 Byte instruction queue, gives

superior power to the system.

Advanced I/O Architecture Speeds Up Data Handling

F2MC-16LX CPU-CORE

ARCHITECTURE

ISD

Peripheral

I/O Registers

IOA

(I/O Address)

(Memory Address)

BAP

Memory

Space

I/O Registers

Interrupt

Request

ICS

Interrupt Controller

Interrupt Control Register

Execution Speed

From request to completion of transfer:

32 cycles = 3.2µs (at 20MHz)

16 bit CPU Core Programming Model

CAN BUS MICROCONTROLLERS

●0.5µm/0.35µm CMOS Technology

●Flash ROM or Mask ROM

versions

●16MHz (62.5ns)/20MHz (50ns)

maximum internal clock speed

from external 4MHz

●On-chip PLL can multiply x1, x2,

x3 or x4 external clock speed

●Internal voltage regulator

supports 3V MCU core offering

low EMI and low power

consumption figures

●Optimised instruction set for

controller applications

•bit, Byte, word, long word data

types

•23 addressing modes

•barrel shifter

•variety of pointers

●4 Byte instruction queue

●Signed multiply instruction –

16 bit x 16 bit

●Signed divide instruction –

32 bit / 16 bit

●EI2OS – Automatic transfer

function independent of CPU with

16 channels of Intelligent I/O

services

●18 bit Time-base timer

●15 bit Watch timer, (devices with

32kHz sub clock only)

●Watchdog timer

●Fast interrupt processing

●Powerful interrupt functions –

8 programmable priority levels,

more than 30 possible hardware

vectors and more than 200

software vectors

F2MC-16LX Microcontrollers with CAN Bus

●Program patch function – facility

to ‘patch over’ mask programmed

code with update from external

memory

●Power saving modes

•7 for single clock or 10 for dual

clock

•sleep, stop, CPU intermittent,

hardware standby …

Features Part ROM/ RAM Clock Ports ICU/OCU Timer/ UART Ser. I/O A/D External Progr. Special Power Supply Pin

Series Flash Byte MHz Counter Conv Bus Pulse Features Saving Volts Count

MB90xxx kB (kHz) Interface Generator Modes

425G/GA MB90427G/GA 64 4096 16 (PLL ext. 58 4 ch/ - 1 x 16 bit 1 ch 1 x 8 bit 8 x 10 bit - 3 ch x 16 bit 1ch CAN2.0B Interface SLEEP, 4.5-5.5 100

MB90F428G/GA 128 6144 4MHz) 4 ch Stepper Motor Driver STOP, 4.5-5.5

Sound generator ….

LCD Controller 4 x 24

495G MB90497G 64 2048 16 (PLL ext. 49 4 ch/ - 2 x 16 bit 2 ch - 8 x 10 bit Yes 4 ch x 8 bit 1 ch CAN2.0B Interface SLEEP 4.5-5.5 64

MB90F497G 64 2048 4MHz) or STOP 4.5-5.5

(32kHz) 2 ch x 16 bit , ...

440G MB90F443G* 128 6144 16 (PLL ext. 81 8 ch/2 ch 2 x 16 bit 2 ch 1 x 8 bit 8 x 10 bit Yes 4 ch x 8 bit 3 ch CAN2.0B Interface SLEEP 4.5-5.5 64

MB90443G** 128 6144 4MHz) or or STOP 4.5-5.5

(32kHz) 6 ch/4 ch 2 ch x 16 bit , ...

540G MB90543G** 128 6144 16 (PLL ext. 81 8 ch/2 ch 2 x 16 bit 2 ch 1 x 8 bit 8 x 10 bit Yes 4 ch x 8 2 ch CAN2.0B Interface SLEEP 4.5-5.5 100

MB90F543G 128 6144 4MHz) or or 16 bit STOP, 4.5-5.5

6 ch/4 ch ...

545G MB90F548G 128 4096 16 (PLL ext. 81 8 ch/2 ch 2 x 16 bit 2 ch 1 x 8 bit 8 x 10 bit Yes 4 ch x 8 1 ch CAN2.0B Interface SLEEP 4.5-5.5 100

MB90548G* 128 4096 4MHz) or or 16 bit STOP, 4.5-5.5

MB90549G* 256 6144 (32kHz) 6 ch/4 ch ... 4.5-5.5

MB90F546G 256 8192 4.5-5.5

590 MB90594G 256 6144 16 (PLL ext. 78 6 ch/6 ch 2 x 16 bit 3 ch 1 x 8 bit 8 x 10 bit - 6 ch x 8 2 ch CAN2.0B Interface SLEEP, 4.5-5.5 100

MB90F594G 256 6144 4MHz) or 16 bit 4 ch Stepper Motor Driver STOP, 4.5-5.5

MB90591 384 8192 Sound generator …. 4.5-5.5

MB90F591 384 8192 4.5-5.5

595 MB90598G 128 4096 16 (PLL ext 78. 4 ch/4 ch 2 x 16 bit 2 ch 1 x 8 bit 8 x 10 bit - 6 ch x 8 1 ch CAN2.0B Interface SLEEP, 4.5-5.5 100

MB90F598G 128 4096 4MHz) or 16 bit 4 ch Stepper Motor Driver STOP, 4.5-5.5

….

*under development **planned

F2MC-16LX DEVICE FEATURES

16 BIT CAN MCU ROADMAP

48 pin

3 CAN

In Production

External

Bus

Interface

External

Bus

Interface

Stepper

Motor

Driver

Stepper

Motor

Driver

External

Bus

Interface

LCD +

Stepper

Motor

Driver

Stepper

Motor

Driver

Samples available Under development Planned

MB90F543G

128kB Flash, 6kB RAM

MB90F591A

384kB Flash, 8kB RAM

MB90591

384kB ROM, 8kB RAM

MB90F594G

256kB Flash, 6kB RAM

MB90594G

256kB ROM, 6kB RAM

MB90F394G

384kB Flash, 10kB RAM

MB90593G

128kB ROM, 4kB RAM

MB90F39x

256kB Flash, 8kB RAM

MB90543G

128kB ROM, 6kB RAM

MB90F39x

512kB Flash, 16kB RAM

MB90F443G

128kB Flash, 6kB RAM

MB90549G

256kB ROM, 6kB RAM

MB90F546G

256kB Flash, 8kB RAM

MB90F497G

64kB Flash, 2kB RAM

MB90F428G/A

128kB Flash, 6kB RAM

MB90F598G

128kB Flash, 4kB RAM

MB90F498G

128kB Flash, 2kB RAM

MB90598G

128kB ROM, 4kB RAM

MB90F548G

128kB Flash, 4kB RAM

MB90428G/A

128kB ROM, 6kB RAM

MB90427G/A

64kB ROM, 4kB RAM

MB90F385

64kB Flash, 2kB RAM

MB90548G

128kB ROM, 4kB RAM

MB90F444G

256kB Flash, 8kB RAM

MB90443G

128kB ROM, 6kB RAM

2 CAN

1 CAN

X0, X1

RSTX

HSTX

X0A,X1A

SCK0

SOT0

SIN 0

SCK1

SOT1

SIN 1

SGO

SGA

ROM: 64kB*

FLASH: 128kB*

RAM: 6kB/4kB*

UART0

UART1

Sound

Generator

External

Interrupt

IN [3:0]

PPG [2:0]

INT [7:0]

TIN

TOT

Clock

Controller

Sub-clock

Prescaler

16LX CPU

I/O Timer

Input Capture

4 channels

16 bit PPG

3 channels

CAN

Controller

16 bit Reload

Timer

1 channel

F MC-16 BUS

Stepper

Motor

Controller

4 Channels

DVCC [1:0]

DVSS [2:0]

PWM 2P [3:0]

PWM 2M [3:0]

PWM 1P [3:0]

PMW 1M [3:0]

AVCC

AVSS

AN [7:0]

AVRH

AVRL

ADTG

10 bit ADC

8 channels

LCD

24 X 4

Low Voltage

Detection Reset

(’A’ version only) V3 - V0

COM [3:0]

SEG23 - SEG0

CAN BUS MICROCONTROLLERS

The MB90425G/GA series offers a

highly integrated CAN solution to

dashboard and other applications

with a wealth of on-chip peripherals

including four stepper motor

controller-drivers, sound generator

and a 24x4 segment LCD controller.

A security feature is incorporated in

this family, preventing the

unauthorised reading of the contents

of the Flash ROM.

Features

●Fujitsu F2MC-16LX microcontroller

architecture

●128kB Flash ROM (with single

voltage and 10k erase cycles), or

64kB Mask ROM

●Flash security feature

●Full CAN 2.0A/2.0B interface with

flexible buffering

●6kB / 4kB RAM

●32kHz sub clock

●LCD controller-driver 24 segments

x 4 commons

●Stepper Motor Controller-Driver

4 channel

●Sound generator

●UART

●Synchronous serial I/O

●External interrupts 8 ch

●A/D converter 10 bit x 8 ch

●Input capture 16 bit x 4 ch

●Reload timer 16 bit x 1 ch

●Programmable pulse generator

16 bit x 3 ch

●Low voltage level detection

(A version only)

●QFP 100 package

●-40 to +105°C temperature range

MB90425G/GA Series with Stepper Motor and LCD controllers Block Diagram

16 BIT SINGLE CAN BUS

MICROCONTROLLERS

* ROM Version = MB90427G/GA (64kB ROM, 4kB RAM)

* FLASH Version = MB90F428G/GA (128kB Flash, 6kB RAM)

F MC-16 BUS

F MC-16LX CPU

16/8 bit PPG

2/4 channels PPG [3:0]

CAN

Controller

I/O Timer

Input Capture

4 channels

FRCK

IN [3:0]

16 bit Reload

Timer

2 channels TOT [1:0]

External

Bus

Interface

EBI

External

Interrupt INT [7:0]

TIN [1:0]

Prescaler

UART1

(SCI)

SOT1

SCK1

SIN1

10 bit ADC

8 channels

AVCC

AVSS

AN [7:0]

AVR

ADTG

UART0

SOT0

SCK0

SIN 0

Prescaler

X0, X1

RSTX

X0A, X1A

Clock

Controller

Sub-clock

RAM 2k*

Flash/ROM

64k*

The MB90495G series brings 16 bit,

full CAN performance to cost

sensitive automotive and industrial

applications which were previously

obliged to use 8 bit basic CAN

devices. It also provides an entry

level to Fujitsu’s range of F2MC-16LX

microcontrollers with on-chip CAN

with full compatibility except that the

number of message buffers is

reduced from 16 to 8.

Features

●Fujitsu F2MC-16LX microcontroller

architecture

●64kB Flash ROM (with single

voltage and 10k erase cycles), or

Mask ROM

●Full CAN 2.0A/2.0B interface with

flexible buffering

●2kB RAM

●32kHz sub clock

●External bus interface

●2 UARTs

●External interrupts 8 ch

●A/D converter 10 bit x 8 ch

●Input capture 16 bit x 4 ch

●Reload timers 16 bit x 2 ch

●Programmable pulse generator

16 bit x 2 ch or 8 bit x 4 ch

●QFP 64 package

●-40 to +105°C temperature range

MB90495G Series 16 bit CAN MCU Block Diagram

16 BIT SINGLE CAN BUS

MICROCONTROLLERS

* ROM Version = MB90497G (64kB ROM, 2kB RAM)

* FLASH Version = MB90F497G (64kB Flash, 2kB RAM)

CAN BUS MICROCONTROLLERS

MB90545G Series General Purpose CAN Block Diagram

16LX CPU

X0, X1

RSTX

HSTX

X0A,X1A

SCK0

SOT0

SIN 0

SCK1

SOT1

SIN 1

SCK2

SOT2

SIN 2

AVCC

AVSS

AN [7:0]

AVRH

AVRL

ADTG

UART0

UART1

(SCI)

Serial I/O

10 bit ADC

8 channels

Clock

Controller

Sub-clock option

Prescaler

F MC-16 BUS

External

Interrupt INT [7:0]

CAN

Controller

PPG [3:0]

8 / 16 bit PPG

4 channels

IN [7:0]

OUT [3:0]

I/O Timer

Input Capture

8 channels ❖

Output Compare

4 channels ❖

External

Bus

Interface EBI

TIN [1:0]

TOT [1:0]

16 bit Reload

Timer

2 channels

ROM:

128kB*/256kB

FLASH:

128kB/256kB*

RAM: 4kB/8kB*

Prescaler

16 BIT SINGLE CAN BUS

MICROCONTROLLERS

The MB90545G series is a product

rich in peripheral features and

designed with more general-purpose

CAN applications. The functions that

particularly distinguish it from other

devices in Fujitsu’s range are the

inclusion of an external bus interface

and a 32kHz sub clock. The

MB90545G series is otherwise

completely plug-compatible with its

double and triple CAN counterparts.

A security feature is incorporated in

this family, preventing the

unauthorised reading of the contents

of the Flash ROM.

Features

●Fujitsu F2MC-16LX microcontroller

architecture

●128kB / 256kB Flash ROM (with

single voltage and 10k erase

cycles), or 128kB Mask ROM

●Flash security function

●Full CAN 2.0A/2.0B interface with

flexible buffering

●4kB / 8kB RAM

●32kHz sub clock

●External bus interface

●2 UARTs

●Synchronous serial I/O

●External interrupts 8 ch

●A/D converter 10 bit x 8 ch

●Input capture 16 bit x 8 ch

●Output compare 16 bit x 4 ch

●Reload timers 16 bit x 2 ch

●Programmable pulse generator

16 bit or 8 bit x 4 ch

●QFP 100 package

●-40 to +105°C temperature range

* ROM Version = MB90548G (128kB ROM, 4kB RAM)

= MB90549G (256kB ROM, 6kB RAM)

* FLASH Version = MB90F548G (128kB Flash, 4kB RAM)

= MB90F546G (256kB Flash, 8kB RAM)

❖Possible combinations: 8 ch ICU & 2 ch OCU or 6 ch ICU & 4 ch OCU

F MC-16 BUS

Clock

Controller 16LX CPU

X0,X1

RSTX

HSTX

Serial I/O

SCK2

SOT2

SIN 2

10 bit ADC

8 channels

AVRH

AVRL

ADTG

AN [7:0]

AVSS

AVCC

Prescaler

UART0

SCK0

SOT0

SIN0

RAM: 4kB*

ROM: 128kB*

FLASH: 128kB*

UART1

SCK1

SOT1

SIN1

I/O Timer

Input Capture

4 channels

Output Compare

4 channels

IN [3:0]

OUT [3:0]

8 / 16 bit PPG

6 channels PPG [5:0]

CAN

Controller

16 bit Reload

Timer

2 channels

TIN

TOT

Stepper

Motor

Controller

4 channels

PWM 1M [3:0]

PWM 1P [3:0]

PWM 2M [3:0]

PWM 2P [3:0]

DVCC [1:0]

DVSS [2:0]

External

Interrupt

INT [7:0]

Prescaler

The MB90595G series is designed for

mid- to high-end 16 bit automotive

applications, especially dashboards as

it features four on-chip stepper motor

controller-drivers. It also contains a

wealth of general-purpose peripherals

such as UARTs, A/D converter and

input capture / output compare.

Features

●Fujitsu F2MC-16LX microcontroller

architecture

●128kB Flash ROM (with single

voltage and 10k erase cycles), or

Mask ROM.

●Full CAN 2.0A/2.0B interface with

flexible buffering

●4kB RAM

●Stepper Motor Controller-Driver

4 channel

●2 UARTs

●Synchronous serial I/O

●External interrupts 8 ch

●A/D converter 10 bit x 8 ch

●Input capture 16 bit x 4 ch

●Output compare 16 bit x 4 ch

●Reload timers 16 bit x 2 ch

●Programmable pulse generator

16 bit or 8 bit x 6 ch

●QFP 100 package

●-40 to +105°C temperature range MB90595G Series General Purpose CAN Block Diagram

16 BIT SINGLE CAN BUS

MICROCONTROLLERS

* ROM Version = MB90598G (128kB ROM, 4kB RAM)

* FLASH Version = MB90F598G (128kB Flash, 4kB RAM)

MB90590

F MC-16 BUS

Clock

Controller

ROM:

256k/384k*

FLASH:

256k/384k*

RAM: 6k/8k*

Prescaler

UART

3 channels

Prescaler

Serial I/O

10 bit ADC

8 channels

Sound

Generator

16LX CPU

I/O Timer

Input Capture

6 channels

Output Compare

6 channels

8 / 16 bit PPG

6 channels

CAN

Controllers

16 bit Reload

Timer

2 channels

Watch Timer

Stepper

Motor

Controller

4 channels

External

Interrupt

X0, X1

RSTX

HSTX

SCK [2:0]

SOT [2:0]

SIN [2:0]

SCK3

SOT3

SIN 3

AVRH

AVRL

ADTG

SGO

SGA

AN [7:0]

AVSS

AVCC

IN [5:0]

OUT [5:0]

PPG [5:0]

Tx [1:0]

Rx [1:0]

TIN

PWM 1M [3:0]

INT [7:0]

TOT / WOT

PWM 1P [3:0]

PWM 2M [3:0]

PWM 2P [3:0]

DVCC [1:0]

DVSS [2:0]

CAN BUS MICROCONTROLLERS

The MB90590 series is designed for

high-end 16 bit automotive

applications, especially dashboards

as it features four on-chip stepper

motor controller-drivers and sound

generator. It also contains a high

quantity of on-chip Flash or Mask

ROM and RAM.

Features

●Fujitsu F2MC-16LX microcontroller

architecture

●256kB / 384kB Flash ROM (with

single voltage and 10k erase

cycles), or Mask ROM

●2 Full CAN 2.0A/2.0B interfaces

with flexible buffering

●6kB / 8kB RAM

●Stepper Motor Controller-Driver

4 channel

●Sound generator

●3 UARTs

●Synchronous serial I/O

●External interrupts 8 ch

●A/D converter 10 bit x 8 ch

●Input capture 16 bit x 6 ch

●Output compare 16 bit x 6 ch

●Reload timers 16 bit x 2 ch

●Programmable pulse generator

16 bit or 8 bit x 6 ch

●QFP 100 package

●-40 to +85°C temperature range

MB90590 Series with Stepper Motor Controllers Block Diagram

* ROM Version = MB90594G (256kB ROM, 6kB RAM)

= MB90591 (384kB ROM, 8kB RAM)

* Flash Version = MB90F594G (256kB Flash, 6kB RAM)

= MB90F591 (384kB Flash, 8kB RAM)

16 BIT DOUBLE CAN BUS

MICROCONTROLLERS

16 BIT DOUBLE CAN BUS

MICROCONTROLLERS

X0, X1

RSTX

HSTX

X0A,X1A

SCK0

SOT0

SIN 0

SCK1

SOT1

SIN 1

SCK2

SOT2

SIN 2

AVCC

AVSS

AN [7:0]

AVRH

AVRL

ADTG

ROM: 128k*

FLASH: 128k*

RAM: 6k*

UART0

UART1

(SCI)

Serial I/O

10 bit ADC

8 channels

External

Interrupt

External

Bus

Interface

IN [7:0]

OUT [3:0]

PPG [3:0]

Tx [1:0]

Rx [1:0]

INT [7:0]

EBI

TIN [1:0]

TOT [1:0]

Clock

Controller

Sub-clock option

Prescaler

16LX CPU

I/O Timer

Input Capture

8 channels ❖

Output Compare

4 channels ❖

8 / 16 bit PPG

4 channels

CAN

Controllers

16 bit Reload

Timer

2 channels

F MC-16 BUS

The MB90540G series is a product

rich in peripheral features and

designed for general-purpose CAN

applications. The functions that

particularly distinguish it from other

devices in Fujitsu’s range are the

inclusion of an external bus interface

and a 32kHz sub clock. The MB90540

series is completely upwards

compatible with its single and triple

CAN counterparts.

A security feature is incorporated

in this family, preventing the

unauthorised reading of the contents

of the Flash ROM.

Features

●Fujitsu F2MC-16LX microcontroller

architecture

●128kB Flash ROM (with single

voltage and 10k erase cycles), or

Mask ROM

●Flash security function

●2 Full CAN 2.0A/2.0B interfaces

with flexible buffering

●6kB RAM

●32kHz sub clock

●External bus interface

●2 UARTs

●Synchronous serial I/O

●External interrupts 8 ch

●A/D converter 10 bit x 8 ch

●Input capture 16 bit x 8 ch

●Output compare 16 bit x 4 ch

●Reload timers 16 bit x 2 ch

●Programmable pulse generator

16 bit or 8 bit x 4 ch

●QFP 100 package

●-40 to +105°C temperature range

MB90540G Series General Purpose CAN Block Diagram

* ROM Version = MB90543G (128kB ROM, 6kB RAM)

* FLASH Version = MB90F543G (128kB Flash, 6kB RAM)

❖Possible combinations: 8 ch ICU & 2 ch OCU or 6 ch ICU & 4 ch OCU

CAN BUS MICROCONTROLLERS

16 BIT TRIPLE CAN BUS

MICROCONTROLLERS

X0, X1

RSTX

HSTX

X0A,X1A

SCK0

SOT0

SIN 0

SCK1

SOT1

SIN 1

SCK2

SOT2

SIN 2

AVCC

AVSS

AN [7:0]

AVRH

AVRL

ADTG

ROM: 128k*

FLASH: 128k*

RAM: 6k*

UART0

UART1

(SCI)

Serial I/O

10 bit ADC

8 channels

External

Interrupt

External

Bus

Interface

IN [7:0]

OUT [3:0]

PPG [3:0]

Tx [2:0]

Rx [2:0]

INT [7:0]

EBI

TIN [1:0]

TOT [1:0]

Clock

Controller

Sub-clock option

Prescaler

16LX CPU

I/O Timer

Input Capture

8 channels ❖

Output Compare

4 channels ❖

8 / 16 bit PPG

4 channels

CAN

Controllers

16 bit Reload

Timer

2 channels

F MC-16 BUS

The MB90440G series offers the

same peripherals as MB90540 and

MB90545 series but features a 3rd

CAN Interface. Thus the migration

between these three series is easy.

Application areas of these products

are demanding automotive body

control applications. An external bus

interface allows to connect off chip

memory.

A security feature is incorporated

in this family, preventing the

unauthorised reading of the contents

of the Flash ROM.

Features

●Fujitsu F2MC-16LX microcontroller

architecture

●128kB Flash ROM (with single

voltage and 10k erase cycles), or

Mask ROM

●Flash security function

●3 Full CAN 2.0A/2.0B interfaces

with flexible buffering

●6kB RAM

●32kHz sub clock

●External bus interface

●2 UARTs

●Synchronous serial I/O

●External interrupts 8 ch

●A/D converter 10 bit x 8 ch

●Input capture 16 bit x 8 ch

●Output compare 16 bit x 4 ch

●Reload timers 16 bit x 2 ch

●Programmable pulse generator

16 bit or 8 bit x 4 ch

●QFP 100 package

●-40 to +105°C temperature range

MB90440G Series General Purpose CAN Block Diagram

* ROM Version = MB90443G (128kB ROM, 6kB RAM)

* FLASH Version = MB90F443G (128kB Flash, 6kB RAM)

* Under development

❖Possible combinations: 8 ch ICU & 2 ch OCU or 6 ch ICU & 4 ch OCU

The Fujitsu RISC (FR) architecture is

a new generation 32 bit

microprocessor core which is

dedicated to resolving the twin

demands of high performance

coupled with low cost, which are

needed by today’s high-end

Automotive, Consumer and Telecoms

applications.

Designed from the outset to be

optimised for embedded applications,

the CPU has a 16 bit instruction Op

Code, enabling maximum

performance from low cost, half word

external memory and instruction

cache widths, or else allowing double

instruction fetches for each bus cycle.

The CPU employs the same five-stage

pipeline and 32 x 32 Multiplier as the

successful SPARClite family but adds

a new barrel shifter and a bit search

unit which finds the first 1, 0 or

change in a data word in a single

cycle. The concept of the instruction

cache architecture with its flexible

locking mechanism is also replicated.

The CPU has eight dedicated

32 bit registers: Program Counter,

Processor Status, interrupt Table

Base Register, Return Pointer,

Supervisor and User Stack Pointers

and two for multiply/divide result.

There are sixteen 32 bit, general-

purpose registers arranged as a

single bank. The functions of R13

to R15 are reserved as Virtual

Accumulator, Frame Pointer and

Stack Pointer respectively. The

instruction set contains many bit

manipulation instructions and data

moving instructions, which are very

helpful in supporting the on-chip

peripheral blocks.

Although the FR is a RISC, it

contains a number of extended

instructions, which help assembly

level programming, often unavoidable

in embedded applications. An

example is the store of half of the

Blocks that require fast access are

connected to the FR-core within a

32 bit Harvard bus system. These

units are the Instruction Cache,

internal RAM, the DMA-Controller and

the bit-Search unit. Resources that

require simple control or status

access, such as UARTs, Timers, etc.,

are hooked up on a 16 bit peripheral

bus known as the R-Bus. The R-Bus

gateway to the FR-core is a

bus-converter module like the one for

the external bus interface. This

general purpose bus, also called the

‘User logic bus’ is used for accessing

the on-chip Flash ROM as well as the

CAN-Interfaces, which typically

require a faster and more extensive

data flow to and from the FR-core

than most of the other on-chip

resources. The external bus also

gives the user the possibility to

access external memory or other

memory-mapped devices on the

target application, supporting seven

fully configurable chip-select areas

with external chip-select pins which

can be controlled individually in terms

of memory-area, bus-width,

wait-states or alignment.

KEY *1: 32 bit x 32 bit: 5 clock cycles *2: 16 bit x 16 bit: 3 clock cycles PC: Program counter

PS: Program status TBR: Table base register RP: Return pointer SSP: System stack pointer

USP: User stack pointer MDH/MDL: Multiplication and division result register

32 bits Data bus

Multiplier ALU Shifter

MDH

MDL

TBR

SSP

USP

Dedicated

registers General-

purpose

registers

R15

CPU Core Diagram

FR SERIES – 32 BIT RISC ARCHITECTURE

CAN BUS MICROCONTROLLERS

FR+CAN BUS MICROCONTROLLERS

The MB91360 series represents not

only a huge leap forward in the level

of integration and performance of

CAN bus microcontrollers but also

should be viewed as a ‘jumping off

point’ for customised and application

specific solutions in Automotive

electronic systems. This will be more

than just a number of individual

products; it is a whole new modular

concept encompassing dashboards,

navigation systems and body

electronics based on Fujitsu’s FR

32 bit RISC CPU. At the heart of these

applications lies Fujitsu’s CAN bus

macro which is in fact implemented

four times on the MB91V360

evaluation device.

Derivatives of the FR+CAN both

for the open market and specific

customers are planned or in design.

A special team within Fujitsu’s

European Microcontroller Design

Centre is dedicated to these projects.

Variations will include stripped down

parts for lower cost body and steering

column applications, versions with

many CAN bus controllers for linking

between different CAN circuits and

high-end types with graphics and LCD

display driving capabilities for

navigation systems.

OCU

CAN

UART

Timer

A/D

Graphics

Controller

ICU

ROM

CAN

VGA

LCD

Driver

PPG RAM FR

CPU CAN

CAN

Stepper

Motor

Control

I Cache

PLL

Clock

Module CAN

Flash

ROM

Building Block Concept

Created in Fujitsu’s 0.35µm CMOS

process, the triple CAN, MB91F361

Flash ROM version contains some

5 million transistors in 160 logical

blocks. The FR CPU clocks at 64MHz

internally and is supported by 1kB of

Instruction cache and 16kB RAM. It is

conceived as the part ideally suited to

the needs of the next generation of

dashboards, including on-chip

features such as stepper motor

controllers, real-time watch timer,

sound generator, high current LED

drivers and PPGs for light dimmers.

It also contains a wealth of general-

purpose peripheral blocks such as

16 channels of 10 bit A/D and

2 channels of 10 bit D/A converter,

4 channels each of input capture and

output compare, six reload timers and

8 external interrupts. Additional serial

communications are 3 UARTs, 2

synchronous serial ports and an I2C.

Power down management features

include reset if the voltage drops

below a defined threshold and over /

under voltage detection interrupt.

Features

●32 bit core CPU; 64MHz / 15.6ns

internal cycle time from 4MHz or

32kHz external clock

●0.35µm CMOS Technology

●Internal voltage regulator

supports 3V MCU core from 5V

supply, offering low EMI and low

power consumption figures

●512kB FLASH ROM; supports

automatic programming, 10,000

erase cycles, 10 year data

retention time, no second

programming voltage required

●1kB Instruction Cache

●16kB static RAM

●5 channels DMA, 3 for external

memory bus and 2 dedicated to

internal peripherals with 16

sources

●Three FULL-CAN interfaces;

conforming to version 2.0 Part A

and Part B, flexible message

buffering (mailbox and FIFO

buffering can be mixed)

●Internal Boot ROM

●External Interrupts: 8 channel

●Power down reset if supply

voltage falls below pre-set

threshold

●Under / Over voltage detection,

generating an interrupt if supply

voltage goes above / below a

pre-set threshold

●A/D Converter: 16 channel

analogue inputs, resolution

10 bits

●D/A Converter: 2 channel

analogue outputs, resolution

10 bits

●ICU (Input capture) 16 bit x 4

channel

●OCU (Output compare) 16 bit x 4

channel

●Programmable Pulse Generator

16 bits x 8 channel

●Stepper Motor Controller 4

channel

●UART, full duplex: 3 channel

●I2C Bus Controller: 1 channel

●Synchronous Serial I/O: 2

channel

●Reload Timer: 16 bit x 6 channel

●LED Driving Port: 8 channel

●Sound Generator

●Real-Time Watch Timer

●Package LQFP208

MB91360 SERIES FR 32 BIT RISC

MICROCONTROLLERS WITH

THREE CAN INTERFACES

CAN BUS MICROCONTROLLERS

MB91360 SERIES BLOCK DIAGRAM

EVA-CHIP

MB91V360

ONLY

DSU

OCU x 4

Free Running

Timer x 2

Sound

I C

PPG x 8

LED x 8

RTim x 6

DAC x 2

ADC x 16

Power Down

Reset

Alarm

Ext. Int x 8

RT Clock

SIO x 2

UART x 3

Trace RAM IF

EMULATOR

Int Control

Watchdog

FR CPU

I-Cache

1kB

Data RAM

12kB

DMA

Bit Search

Harvard Bus Converter

Boot ROM

2kB

Fast RAM

4kB

R-Bus

Interface

Ext. Bus

Interface

Ext. Bus

CAN x 3

*Flash/ROM

512kB

Clock Module

Low Power

Unit

DATA

INSTR

ICU x 4

Stepper Motor

Controller x 4

EVA-CHIP

MB91V360

ONLY

EVA-CHIP

MB91V360

16kB 32 16

MB91360 Series Block Diagram

* ROM version MB91361 (512kB ROM, 16kB RAM)

* Flash version MB91F361 (512kB Flash, 16kB RAM)

REALOS & OSEK/VDX

REALOS Real-Time OS for the

FR Series

REALOS/FR is a Real-Time OS for the

FR Series of microcontrollers which

conforms to Version 3.0 of the

µITRON specification.

Features

●High speed system calls

●High speed interrupt processing

●Up to 32,767 tasks

●Up to 32 priorities

●50 system calls

●Priority based and event driven

scheduling system

●Kernel size from 2.7kB (min) to

7.2kB (max)

●Multi-windows based Configurator

which creates executable program

with optimised environment of

kernel and application programs

●Sample I/O driver

●Sample program

●Debugger macro enabling

ordinary debugger to perform

debugging of µITRON tasks

●Multi-windows based REALOS

debugger, capable of working at

the C level

REALOS Real-Time OS for the

F2MC-16L/LX Families

REALOS/907 is a Real-Time OS for

the F2MC-16L/LX families of

microcontrollers which conforms to

Version 2.01 of the µITRON

specification.

Features

●High speed system calls

●High speed interrupt processing

●Up to 255 tasks

●Up to 16 priorities

●46 system calls

●Priority based and event driven

scheduling system

●Kernel size from 0.8kB (resident)

to 5.9kB (max)

●Multi-windows based Configurator

which creates executable program

with optimised environment of

kernel and application programs

●Sample I/O driver

●Sample program

●Debugger macro enabling ordinary

debugger to perform debugging of

µlTRON tasks

●Multi-windows based REALOS

debugger, capable of working at

the C level

OSEK/VDX

OSEK/VDX is an operating system

targeted for automotive applications.

It consists of three parts, the OSEK

kernel, the communications interface

and the network management. Mainly

automotive controller networks using

CAN interfaces will employ the OSEK

operating system. Both the F2MC-16LX

and FR series microcontrollers are

supported with optimised drivers for

the Fujitsu CAN controller.

OSEK-OS defines the task types

‘Basic’ and ‘Extended’. Basic tasks

cannot have a waiting state and so are

suitable for those which run

completely after each activation.

Extended tasks can react to events;

they can have a waiting state.

OSEK-OS also defines four

conformance classes:

●BCC1 – basic tasks, single

activation

●BCC2 – basic tasks, multiple

activation

●ECC1 – basic and extended

tasks, single activation

●ECC2 – basic and extended

tasks, multiple activation

The FR series OSEK without CAN

driver and network management

requires 3.2kB ROM for class ECC1

(standard status)

CAN BUS MICROCONTROLLERS

EUROS

EUROS Enhanced Universal Real-

Time Operating System

EUROS is an innovative real-time

operating system characterised by

short response times, robustness,

scalability and flexibility. The primary

aim of EUROS development was to

create a uniform, hardware-

independent operating system for

real-time and embedded applications

which takes into account the growing

complexity and diversity of processor

architectures, in order to make

software engineering as economical

as possible. It separates the user

software from the hardware so that

the application can easily be ported to

state-of-the-art hardware.

Key Features

●supports Fujitsu F2MC-16LX and

FR series

●unlimited number of system

objects (tasks, mailboxes, signals,

events, semaphores, drivers)

●up to 256 priorities

●synchronous and asynchronous

system calls

●memory management supports

fixed and variable size memory

blocks

●waiting on multiple objects

●flexible open driver interface

●priority based scheduler with

round robin support

●named system objects organised

in clusters (hierarchical object

trees)

●re-entrant ANSI compatible C

runtime library

●generic graphic library

●TCP/IP network stack (BSD4.4

socket interface)

●Web server, FTP server, SMTP

client, BOOTP client

●PPP, Ethernet

●CAN / CANopen

●MS-DOS™ compatible file system

●IDE hard disk drivers

●Floppy disk drivers

●Ramdisk, FTL for Flashdisks

●IrDA (IrLAP, IrLMP, IrComm)

●Profibus (slave)

●IEEE1394 (Firewire™)

EUROSvm Euros Virtual Machine

EUROSvm is an implementation of

the Java Virtual Machine Specification

V1.2. It has been designed for

real-time and embedded systems and

offers unparalleled support for this

target domain. Among the

extraordinary features of EUROSvm

are:

●Hard real-time execution

●Minimal footprint

●ROMable code

●Native code support

●Dynamic linking

●Fast execution

Contact Information

Dr. Kaneff Engineering Consultants

Neutorgraben 17

D-90419 Nuremberg, Germany

Tel: ++49 (911) 33 84 33

Fax: ++49 (911) 33 86 06

www.kaneff.de

info@kaneff.de

FLASH/CAN 64 EVALUATION BOARD

The Flash/CAN 64 is a low cost

multifunctional evaluation board for

the Fujitsu 16 bit Flash

microcontroller series MB90560,

MB90560L, MB90565 and

Flash+CAN series MB90495G. It can

be used stand-alone for software

development and testing or as a

simple target board to work with the

emulator system. The board allows

the designer to start immediately with

the software development before his

own final target system is available.

Features

●Supports 16 bit LX series

MB90495G, MB90560, MB90560L

and MB90565

●Fully supports 3V and 5V

environment

●QFP-64 or DIP-64 sockets for

device or emulator connection

●In-Circuit serial Flash

programming

●High-speed CAN driver and

connector

●All resources available for

evaluation

●All pins routed to connectors

●4MHz main crystal

●32Hz sub clock crystal for

MB90495G series

●Two UART interfaces (3V and 5V

operating)

●8 User LEDs

●Reset button

●Two buttons configurable for

external interrupts

●Prototyping area

●Order code:

FLASH-CAN-64P-M01/M09

Flash/CAN 64 evaluation board

CAN BUS MICROCONTROLLERS

FLASH/CAN 100 EVALUATION BOARD

The Flash/CAN 100 board was

developed, in order to allow a fast

software design start for customers

wishing to use Fujitsu Flash and / or

CAN MCUs in the 100-pin

QFP package. Since Fujitsu

in-circuit emulators require a

target system that provides

Vcc and GND, as well as an

oscillation circuit, it enables

customers to start development or

evaluation work straight away without

having to wait for their own target

hardware. Additionally, since most

Fujitsu Flash microcontrollers have

the burn-in Flash programming

algorithm which enables in-circuit

programming of blank devices, this is

also supported via an RS232

connection.

The Flash/CAN100 Board Features

●100-pin socket adaptor for

device or emulator connection

●On-board regulator allows 7-14V

unstabilised external DC power

supply

●5V and 3.7V internal power supply

available for emulator

●Two high-speed CAN drivers

●RS232 interface

●All MCU pins brought out twice

to external connectors

●Optional sub-clock

●RST, HST push-button

●8 test LEDs

●External reset via RS232

Flash/CAN 100 evaluation board

The Flash/CAN100 is supplied with

the MB90F598 single-CAN, 128kByte

Flash microcontroller but is able to

support all of the following device

types:

- MB90540G (MB90F543G,

MB90543G)

- MB90545G (MB90F546G,

MB90549G, MB90F548G,

MB90548G)

- MB90550A (MB90F553A,

MB90553A)

- MB90580 (MB90F583B,

MB90583B)

- MB90590 (MB90F594G,

MB90594G, MB90F591,

MB90591)

- MB90595G (MB90F598G,

MB90598G)

The order code for the kit is

FLASH-CAN2-100P-M06 and it is

delivered with:

●The Flash/CAN100 board itself

●Two 50-pin socket connectors

●Power supply connector

●MB90F598 - 128kB Flash

microcontroller

●11 Jumpers

●1 socket adapter cover

●English documentation

DEVKIT16

The DevKit16, comprising main board and CPU board

The DevKit16 is a multi-function,

modular starterkit which provides plug

and play evaluation of Fujitsu

F2MC-16L/LX microcontrollers and

software tools. The kit hardware

consists of two parts, a main board

which carries the emulation memory,

ROM monitor debugger and

communications functions and an

interchangeable CPU board, which

carries either a soldered MB90F543PF

controller device or a socket. This

socket enables it to accept other

F2MC-16L/LX device types in 100-pin

QFP, or act purely as an emulator

target, with or without the main

board. Flash serial programming and

CAN Bus connectivity are also

supported. Each kit comes with a

Fujitsu CD ROM containing the

complete documentation and Softune

Workbench tool chain. Also provided

is an evaluation licence copy of

Processor ExpertTM from Unis, which

is an environment with resource

oriented application design and CPU

expert knowledge for rapid application

development.

CPU Board Features

●Soldered MB90F543PF MCU

(DevKit16-F543) or

NQ-PACK100RB socket

(DevKit16-MCU100)*

●Power supply regulators for 5V

or 3.3V depending on device

●Main and sub clock crystals

●Flash serial programming

interface

●Connectors for all MCU pins

●Device bus Euro connector for

customer’s own application board

●Interface bus connector to main

board

DevKit16-Main - Board Features

●512kB RAM, upgradable to 2MB

●128kB Flash memory, upgradable

to 2MB

●Additional external ports to

replace those lost when device is

in external bus mode

●3 RS232 interfaces – 2 for MCU,

one for board

●2 high speed CAN Bus drivers and

connectors

●2 digit LED display with buffer,

8 test LEDs, diagnostic LED

●PC-AT keyboard interface with

connector

●Amplifier and speaker for device

PPG or sound generator

●User-programmable FPGA

Software Support Features

●Fujitsu Softune Workbench with

tools – C compiler, assembler,

linker…

●Fujitsu monitor debugger

●Processor ExpertTM development

environment

●Processor ExpertTM debugger

kernel

●Flash serial programming utility

for MCU Flash or main board

Flash

●Sample projects

●Main board diagnostic utility

*Under development

CAN BUS MICROCONTROLLERS

STARTERKIT MB91360

The MB91360 Starterkit is a

stand-alone application board that

makes it easy to evaluate and

demonstrate almost all features of the

MB91360 microcontroller series.

Along with the supplied Windows-

based development tools, it can be

used as a system for user program

developments.

The board can be configured as a

target for the MB91360 emulation-

system or, by using the included

MB91F361 device as a stand-alone

evaluation board. All peripheral

functions are available on external

pin-headers in order to design and

test user applications cost- and

time-effectively. For some resource

functions, additional hardware is

already present on the board (e.g.

CAN- and UART-transceivers, LEDs,

Buttons, etc).

Key Features

●Footprint QFP208 (0.5mm pitch)

for MB91F361 (or emulation

socket), surrounded by headers

for test-pins, etc.

●4MHz or 32kHz crystal selectable

●DC power-supply circuit (incl.

testpins for Vcc, GND, power-LED

and switch)

●512kB external SRAM available for

user code and data

●External 16550 UART (supports

transfer-rates up to 115.2 kBaud)

●3 Resets (‘Monitor’=Flash

monitor, ‘User’=external RAM,

‘Flash’=User Flash Area)

●2 MAX232 + DB9 (female)

connectors for monitor and

MB91360 Starterkit

internal UART

●CAN transceiver and DB9 (male)

for internal CAN0

●External interrupt 0 and 1

connected to buttons for user

interaction

●Various jumpers for individual

configuration

●2x16 char LCD (on Port G)

●8 LEDs (on Port J)

●External bus and all resources

logically grouped on pin-headers

●Area for extensions (2.54mm

grid)

●Stand-alone configuration

features built-in monitor

debugger (in Flash)

●Software example projects for

various applications

EMDC is housed in Fujitsu’s European headquarters near Frankfurt

Fujitsu’s European Microcontroller Design Centre

provides a multitude of design solutions

The European Microcontroller Design

Centre (EMDC) was established in

July 1997 at Fujitsu FME’s European

headquarters near Frankfurt.

The Centre represents a major

investment in a market area of

great strategic significance, and

handles design projects and

development support involving both

standard microcontrollers and

customised products.

Fujitsu can provide the basis for

solutions to numerous applications

from its wide portfolio of 8, 16 and

32 bit microcontroller devices.

The Centre is focusing on some of

the largest sectors for

microcontrollers – automotive,

industrial, and audio/video.

In the automotive marketplace,

critical areas on which the Centre

concentrates, include

instrumentation, navigation, and in-

car communications. The CAN

protocol controller forms the focus

for the Centre.

EUROPEAN MICROCONTROLLER

DESIGN CENTRE

CAN devices designed at the Fujitsu EMDC

REPRESENTATIVES

USA

Alabama

ComRep, Inc.

190 Lime Quarry Road, Ste 212

Madison, AL 35758

Tel: 256/772-9982

Fax: 256/772-869

Arizona

Millenium Sales

2222 East Camelback Road, Ste 222

Phoenix, AZ 85016

Tel: 602/707-5600

Fax: 602/707-5605

California

Infinity Sales, Inc.

26560 W. Agoura Road, Ste 203

Calabasas, CA 91302

Tel: 818/880-6480

Fax: 818/880-1922

Innovation Sales

6440 Lusk Blvd., Ste D200

San Diego, CA 92121

Tel: 858/535-9300

Fax: 858/550-3707

Infinity Sales, Inc.

20 Corporate Park, Ste 100

Irvine, CA 92606

Tel: 949/833-0300

Fax: 949/833-0303

Insight Electronics

9980 Huennekens Street

San Diego, CA 92121

Tel: 858/450-8500

Fax: 858/780-8552

Paragon Technical, Inc.

3350 Scott Blvd., Bldg. 23A

Santa Clara, CA 95054

Tel: 408/969-0900

Fax: 408/969-0222

Colorado

Innovation Sales

2450 Central Ave, Ste P-5

Boulder, CO 80301

Tel: 303/02-9300

Fax: 303/402-9500

Connecticut

PROCOMP

4 Norris Lane

Brookfield, CT 06804

Tel: 203/775-4740

Fax: 203/775-4740

R.C. Merchant & Co., Inc.

815 Main Street

St. Joseph, MI 49085

Tel: 616/983-7378

Fax: 616/983-3506

Minnesota

Beta Technology

18283 Minnetonka Blvd., Ste C

Deephaven, MN 55391

Tel: 612/473-2680

Fax: 612/473-2690

New Jersey

Technical Applications & Marketing (TAM)

91 Clinton Road, Ste 1D

Fairfield, NJ 07004

Tel: 973/575-4130

Fax: 973/575-4563

New York

Quality Components

116 Fayette Street

Manlius, NY 13104

Tel: 315/682-8885

Fax: 315/682-2277

North Carolina

ComRep, Inc.

Jefferson Square

308-D West Millbrook Rd.

Raleigh, NC 26709

Tel: 919/845-6369

Fax: 919/845-6358

ComRep, Inc.

8318 Pineville-Matthews Rd.

Suite 281J

Charlotte, NC 28226

Tel: 704/341-7747

Fax: 704/341-7748

Ohio

Mid-Star

35 Compark Road, Ste 204

Centerville, OH 45459

Tel: 937/439-5700

Fax: 937/439-6657

Mid-Star

4312 Harper Street

Perry, OH 44081

Tel: 440/259-2408

Fax: 440/259-2409

Mid-Star

2530 Revere Drive

Akron, OH 44081

Tel: 330/864-7633

Fax: 216/274-6456

Florida

Semtronic Associates

14004 Roosevelt Blvd., Ste 604

Clearwater, FL 33762

Tel: 727/507-0504

Fax: 727/539-0601

Semtronic Associates

3301 NW 55th Street

Ft. Lauderdale, FL 33309

Tel: 954/731-2484

Fax: 954/731-1019

Semtronic Associates

600 S. Northlake Blvd., Ste 270

Altamonte Springs, FL 32701

Tel: 407/831-0451

Fax: 407/831-6055

Georgia

ComRep, Inc.

3260 Peachtree Industrial Blvd., Ste 10

Duluth, GA 30096

Tel: 770/814-9959

Fax: 770/814-9960

Illinois

Core Sales

1721 Moonlake Blvd.

Hoffman Estates, IL 46038

Tel: 847/843-8888

Fax: 847/490-5354

Indiana

VAI Technology

11451 Overlook Drive

Fishers, IN 46038

Tel: 317/570-0707

Fax: 317/845-8650

Massachusetts

PROCOMP

1049 East St.

Tewksbury, MA 01876

Tel: 978/858-0100

Fax: 978/858-0110

Maryland

Arbotek Associates, Inc.

4550 M Ritchie Hwy, Ste 148

Severna Park, MD 21146

Tel: 301/865-8655

Fax: 301/865-8654

Michigan

R.C. Merchant & Co., Inc.

23735 Research Drive

Farmington Hills, MI 48335

Tel: 248/476-4600

Fax: 248/476-3162

Oregon

Phase II Technical Sales

9400 S.W. Beaverton-Hillsdale Hwy.

Suite 140

Beaverton, OH 97005

Tel: 503/292-7922

Fax: 503/292-703

Texas

Technical Marketing, Inc.

3320 Wiley Post Road

Carrollton, TX 75006

Tel: 972/387-3601

Fax: 972/387-3605

Technical Marketing, Inc.

2835 Wilcrest, Ste 210

Houston, TX 77042

Tel: 713/783-4497

Fax: 713/783-5307

Technical Marketing, Inc.

3445 Executive Center Drive, Ste 252

Austin, TX 78731

Tel: 512/343-6976

Fax: 512/343-7986

Utah

Innovation Sales

3005 Dickens Place

Salt Lake City, UT 84108

Tel: 801/583-7880

Fax: 801/583-7881

Virginia

Arbotek Associates, Inc.

4121 Plank Road, Ste 422

Fredericksburg, VA 22407

Tel: 540/785-2856

Fax: 603/853-9251

Washington

Phase II Technical Sales

12025 115th Ave., NE, Ste 200

Kirkland, WA 98034

Tel: 425/821-8313

Fax: 425/823-4089

Argentina

Insight Electonics

Blanco Encalada #193 oficina 35

San Ysidro, BS, Argentina

C.P. 1642

Tel: 011 (54114) 735-2659

Brazil

Insight Electronics

Rua Alcides Ricardini neves

12-CJ 1306-050

CEP 04575-050

Sao Paulo, SP, Brasil

Tel: 011 (5511) 5505-6501

Fax: 011 (5511) 5505-6702

Insight Electronics

Rua Gil Stein Ferreira

357-Sala 607-6 Andar

CEP 88301-210

Itaja, SC, Brasil

Tel: 011 (5547) 348-6488

Fax: 011 (5547) 344-4747

Insight Electronics

Rua Teodoro Langaard, 815

13070-060

Campinas, SP, Brasil

Tel: 011 (5519) 243-0090

Fax: 011 (5519) 212-2773

Canada

Pipe-Thompson Technologies, Inc.

2155 Dunwin Drive, Unit #7

Mississauga, Ontario L5L 4M1

Tel: 905/607-1850

Fax: 905/607-1858

Pipe-Thompson Technologies, Inc.

38 Auriga Drive, Ste 254

Nepean, Ontario K2D 8A5

Tel: 613/723-6494

Fax: 613/723-0969

Mexico

Insight Electronics

Carretera Base Aerea Militar

#5850 Km.5, Edif. 9

Zapopan, Jalisco, Mexico

C.P. 45100

Tel: 011 (523) 818-3286

Fax: 011 (523) 818-3291

Insight Electronics

Cerro de la Silla, #600 B-13

Fracc Monterrey

Tijuana, B.C. Mexico, CP 2210070

Tel: 011 (526) 684-4748

Fax: 011 (526) 684-4749

Insight Electronics

Montecito #38 Edificio World Trade

Center

Col. Napoles CP 03810

Mexico

Tel: 011 (525) 488-0119

Fax: 011 (525) 488-0179

Insight Electronics

Mision de Guadalupe No. 1968

Av Compas Eliseos #9050

1A First Floor

Fraccionamiento Campos Eliseos

CD Juarez, Chihuahua, Mexico

Tel: 011 (521) 625-0503

Fax: 011 (521) 625-0524

Insight Electronics

Ave. Fundidora #502

Edificio Centermex Local #99

Monterrey, Mexico, CP 64010

Tel: 011 (528) 369-6711

Fax: 011 (528) 369-6713

Puerto Rico

Semtronic Associates

#125 Carita St.

Crown Hills, PR 00926

Tel: 787/766-0700

Fax: 787/763-8071

DISTRIBUTORS

USA

Impact Technologies

Tel: 858/622-8110

www.impactna.com

Pioneer-Standard

Tel: 440/519-6200

www.pios.com

Canada

Impact Technologies

www.impactna.com

Pioneer-Standard

Tel: 440/519-6200

www.pios.com

South America

Insight Electronics

Mexico: 011 (525) 788-0119

Argentina: 011 (541) 735269

Brazil: 011 (5511) 5505-6702

www.insight-electronics.com

CAN BUS MICROCONTROLLERS

FME-CANBUS-0201-a

SALES OFFICES

Atlana

2400 Lakeview Parkway, Suite 675

Alpharetta, GA 30004

Boston

1601 Trapelo Road, 2nd Floor

Waltham, MA 02154-7300

Chicago

767 Pennsylvania Ave., Suite 2

Palantine, IL 60074

Dallas

Dominion Plaza ‘A’

17304 Preston Road, Suite 750

Dallas, TX 75252-5675

Denver

12000 North Washington Street

Suite 370

Thornton, CO 80241-1900

Irvine

Century Centre

2603 Main Street, Suite 510

Irvine, CA 92614-6232

Minneapolis

3800 W. 80th Street, Suite 430

Bloomington, MN 55431-4419

New York

Hauppauge Office Park

Building 2, Suite 420

898 Veterans Memorial Highway

Hauppauge, NY 11788-2941

Portland

9900 SW Wilshire #220

Portland, OR 97225

San Jose

30 Rio Robles

San Jose, CA 95134

FUJITSU MICROELECTRONICS, INC.

Corporate Headquarters

3545 North First Street, San Jose, California 95134-1804

Tel: (800) 866-8608 Fax: (408) 922-9179

E-mail: fmicrc@fmi.fujitsu.com Internet: http://www.fujitsumicro.com