74HC123D
1
CMOS Digital Integrated Circuits Silicon Monolithic
74HC123D
74HC123D
74HC123D
74HC123D
Start of commercial production
2016-05
1.
1.
1.
1. Functional Description
Functional Description
Functional Description
Functional Description
• Dual Monostable Multivibrator
2.
2.
2.
2. General
General
General
General
The 74HC123D is a high speed CMOS MONOSTABLE MULTIVIBRATOR fabricated with silicon gate C2MOS
technology.
It achieves the high speed operation similar to equivalent LSTTL while maintaining the CMOS low power
dissipation.
There are two trigger inputs, A input (negative edge), and B input (positive edge). These inputs are valid for a
slow rise/fall time signal (tr = tf = 1 s) as they are schmitt trigger inputs. This device may also be triggered by
using CLR input (positive edge).
After triggering, the output stays in a MONOSTABLE state for a time period determined by the external resistor
and capacitor (RX, CX). A low level at the CLR input breaks this state. In the MONOSTABLE state, if a new
trigger is applied, it extends the MONOSTABLE period (retrigger mode).
Limits for CX and RX are:
External capacitor, CX: No limit
External resistor, RX: VCC = 2.0 V more than 5 kΩ
VCC ≥ 3.0 V more than 1 kΩ
All inputs are equipped with protection circuits against static discharge or transient excess voltage.
3.
3.
3.
3. Features (Note)
Features (Note)
Features (Note)
Features (Note)
(1) High speed: tpd = 25 ns (typ.) at VCC = 5 V
(2) Low power dissipation:
Standby state: ICC = 4.0 µA (max) at Ta = 25
Active state: ICC = 1000 µA (max) at Ta = 25
(3) Balanced propagation delays: tPLH ≈ tPHL
(4) Wide operating voltage range: VCC(opr) = 2.0 to 6.0 V
Note: In the case of using only one circuit, CLR should be tied to GND, RX/CXCXQQ should be tied to OPEN,
the other inputs should be tied to VCC or GND.
4.
4.
4.
4. Packaging
Packaging
Packaging
Packaging
SOIC16
2017-03-03
Rev.3.0
©2016 Toshiba Corporation
74HC123D
2
5.
5.
5.
5. Pin Assignment
Pin Assignment
Pin Assignment
Pin Assignment
6.
6.
6.
6. Marking
Marking
Marking
Marking
7.
7.
7.
7. IEC Logic Symbol
IEC Logic Symbol
IEC Logic Symbol
IEC Logic Symbol
2017-03-03
Rev.3.0
©2016 Toshiba Corporation
74HC123D
3
8.
8.
8.
8. Truth Table
Truth Table
Truth Table
Truth Table
X: Don't care
9.
9.
9.
9. Block Diagram
Block Diagram
Block Diagram
Block Diagram
(1) CX, RX, DX are external
Capacitor, resistor, and diode, respectively.
(2) External clamping diode, DX;
The external capacitor is charged to VCC level in the wait state, i.e. when no trigger is applied.
If the supply voltage is turned off, CX is discharges mainly through the internal (parasitic) diode. If CX is
sufficiently large and VCC drops rapidly, there will be some possibility of damaging the IC through in
rush current or latch-up. If the capacitance of the supply voltage filter is large enough and VCC drops
slowly, the in rush current is automatically limited and damage to the IC is avoided.
The maximum value of forward current through the parasitic diode is ±20 mA.
In the case of a large CX, the limit of fall time of the supply voltage is determined as follows:
tf ≥ (VCC - 0.7) CX/20 mA
(tf is the time between the supply voltage turn off and the supply voltage reaching 0.4 VCC.)
In the even a system does not satisfy the above condition, an external clamping diode (DX) is needed to
protect the IC from rush current.
2017-03-03
Rev.3.0
©2016 Toshiba Corporation
74HC123D
4
10.
10.
10.
10. System Diagram
System Diagram
System Diagram
System Diagram
11.
11.
11.
11. Timing Chart
Timing Chart
Timing Chart
Timing Chart
2017-03-03
Rev.3.0
©2016 Toshiba Corporation
74HC123D
5
12.
12.
12.
12. Functional Description
Functional Description
Functional Description
Functional Description
(1) Standby state
The external capacitor (CX) is fully charged to VCC in the stand-by state. That means, before triggering,
the QP and QN transistors which are connected to the RX/CX node are in the off state. Two comparators
that relate to the timing of the output pulse, and two reference voltage supplies turn off. The total supply
current is only leakage current.
(2) Trigger operation
Trigger operation is effective in any of the following three cases. First, the condition where the A input is
low, and the B input has a rising signal; second, where the B input is high, and the A input has a falling
signal; and third, where the A input is low and the B input is high, and the CLR input has a rising signal.
After a trigger becomes effective, comparators C1 and C2 start operating, and QN is turned on. The
external capacitor discharges through QN. The voltage level at the RX/CX node drops. If the RX/CX voltage
level falls to the internal reference voltage VrefL, the output of C1 becomes low. The flip-flop is then reset
and QN turns off. At that moment C1 stops but C2 continues operating.
After QN turns off, the voltage at the RX/CX node starts rising at a rate determined by the time constant
of external capacitor CX and resistor RX.
Upon triggering, output Q becomes high, following some delay time of the internal F/F and gates. It stays
high even if the voltage of RX/CX changes from falling to rising. When RX/CX reaches the internal
reference voltage VrefH, the output of C2 becomes low, the output Q goes low and C2 stops its operation.
That means, after triggering, when the voltage level of the RX/CX node reaches VrefH, the IC returns to
its MONOSTABLE state.
With large values of CX and RX, and ignoring the discharge time of the capacitor and internal delays of
the IC, the width of the output pulse, twOUT, is as follows:
twOUT = 1.0 × CX × RX
(3) Retrigger operation
When a new trigger is applied to either input A or B while in the MONOSTABLE state, it is effective only
if the IC is charging CX. The voltage level of the RX/CX node then falls to VrefL level again. Therefore the
Q output stays high if the next trigger comes in before the time period set by CX and RX.
If the new trigger is very close to previous trigger, such as an occurrence during the discharge cycle, it
will have no effect.
The minimum time for a trigger to be effective 2 nd trigger, trr (min), depends on VCC and CX.
(4) Reset operation
In normal operation, the CLR input is held high. If CLR is low, a trigger has no effect because the Q
output is held low and the trigger control F/F is reset. Also, QP turns on and CX is charged rapidly to VCC.
This means if CLR is set low, the IC goes into a wait state.
2017-03-03
Rev.3.0
©2016 Toshiba Corporation
74HC123D
6
13.
13.
13.
13. Absolute Maximum Ratings (Note)
Absolute Maximum Ratings (Note)
Absolute Maximum Ratings (Note)
Absolute Maximum Ratings (Note)
Characteristics
Supply voltage
Input voltage
Output voltage
Input diode current
Output diode current
Output current
VCC/ground current
Power dissipation
Storage temperature
Symbol
VCC
VIN
VOUT
IIK
IOK
IOUT
ICC
PD
Tstg
Note Rating
-0.5 to 7.0
-0.5 to VCC + 0.5
-0.5 to VCC + 0.5
±20
±20
±25
±50
500
-65 to 150
Unit
V
V
V
mA
mA
mA
mA
mW
Note: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even
destruction.
Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings and the operating ranges.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report
and estimated failure rate, etc).
14.
14.
14.
14. Operating Ranges (Note)
Operating Ranges (Note)
Operating Ranges (Note)
Operating Ranges (Note)
Characteristics
Supply voltage
Input voltage
Output voltage
Operating temperature
Inputriseandfalltimes
External capacitor
External resistor
Symbol
VCC
VIN
VOUT
Topr
tr,tf
CX
RX
Note
(Note 1)
(Note 1)
Test Condition
VCC = 2.0 V
VCC = 4.5 V
VCC = 6.0 V
VCC = 2.0 V
VCC ≥ 3.0 V
Rating
2.0 to 6.0
0 to VCC
0 to VCC
-40 to 85
0 to 1000
0 to 500
0 to 400
No limitation
≥ 5 k
≥ 1 k
Unit
V
V
V
ns
ns
ns
F
Ω
Ω
Note: The operating ranges must be maintained to ensure the normal operation of the device.
Unused inputs must be tied to either VCC or GND.
Note 1: The maximum allowable values of CX and RX are a function of leakage of capacitor CX, the leakage of
74HC123D, and leakage due to board layout and surface resistance.
Susceptibility to externally induced noise signals may occur for RX > 1 MΩ.
2017-03-03
Rev.3.0
©2016 Toshiba Corporation
74HC123D
7
15.
15.
15.
15. Electrical Characteristics
Electrical Characteristics
Electrical Characteristics
Electrical Characteristics
15.1.
15.1.
15.1.
15.1. DC Characteristics (Unless otherwise specified, T
DC Characteristics (Unless otherwise specified, T
DC Characteristics (Unless otherwise specified, T
DC Characteristics (Unless otherwise specified, Ta
a
a
a = 25
= 25
= 25
= 25
)
)
)
)
Characteristics
High-level input voltage
Low-level input voltage
High-level output voltage
Low-level output voltage
Input leakage current
RX/CX terminal OFF-state current
Quiescent supply current
Active-state supply current
(per circuit)
Symbol
VIH
VIL
VOH
VOL
IIN
IIN
ICC
ICC(opr)
Test Condition
VIN = VIH or VIL
VIN = VIH or VIL
VIN = VCC or GND
VIN = VCC or GND
VIN = VCC or GND
VIN = VCC or GND
RX/CX = 0.5 VCC
IOH = -20 µA
IOH = -4 mA
IOH = -5.2 mA
IOL = 20 µA
IOL = 4 mA
IOL = 5.2 mA
VCC (V)
2.0
4.5
6.0
2.0
4.5
6.0
2.0
4.5
6.0
4.5
6.0
2.0
4.5
6.0
4.5
6.0
6.0
6.0
6.0
2.0
4.5
6.0
Min
1.50
3.15
4.20
1.9
4.4
5.9
4.18
5.68
Typ.
2.0
4.5
6.0
4.31
5.80
0.0
0.0
0.0
0.17
0.18
45
400
700
Max
0.50
1.35
1.80
0.1
0.1
0.1
0.26
0.26
±0.1
±0.1
4.0
200
500
1000
Unit
V
V
V
V
V
V
V
µA
µA
µA
µA
2017-03-03
Rev.3.0
©2016 Toshiba Corporation
74HC123D
8
15.2.
15.2.
15.2.
15.2. DC Characteristics (Unless otherwise specified, T
DC Characteristics (Unless otherwise specified, T
DC Characteristics (Unless otherwise specified, T
DC Characteristics (Unless otherwise specified, Ta
a
a
a = -40 to 85
= -40 to 85
= -40 to 85
= -40 to 85
)
)
)
)
Characteristics
High-level input voltage
Low-level input voltage
High-level output voltage
Low-level output voltage
Input leakage current
RX/CX terminal OFF-state current
Quiescent supply current
Active-state supply current
(per circuit)
Symbol
VIH
VIL
VOH
VOL
IIN
IIN
ICC
ICC(opr)
Test Condition
VIN = VIH or VIL
VIN = VIH or VIL
VIN = VCC or GND
VIN = VCC or GND
VIN = VCC or GND
VIN = VCC or GND
RX/CX = 0.5 VCC
IOH = -20 µA
IOH = -4 mA
IOH = -5.2 mA
IOL = 20 µA
IOL = 4 mA
IOL = 5.2 mA
VCC (V)
2.0
4.5
6.0
2.0
4.5
6.0
2.0
4.5
6.0
4.5
6.0
2.0
4.5
6.0
4.5
6.0
6.0
6.0
6.0
2.0
4.5
6.0
Min
1.50
3.15
4.20
1.9
4.4
5.9
4.13
5.63
Max
0.50
1.35
1.80
0.1
0.1
0.1
0.33
0.33
±1.0
±1.0
40.0
260
650
1300
Unit
V
V
V
V
V
µA
µA
µA
µA
15.3.
15.3.
15.3.
15.3. Timing Requirements (Unless otherwise specified, T
Timing Requirements (Unless otherwise specified, T
Timing Requirements (Unless otherwise specified, T
Timing Requirements (Unless otherwise specified, Ta
a
a
a = 25
= 25
= 25
= 25
, Input: t
, Input: t
, Input: t
, Input: tr
r
r
r = t
= t
= t
= tf
f
f
f = 6 ns)
= 6 ns)
= 6 ns)
= 6 ns)
Characteristics
Minimum pulse width
Minimum pulse width
(CLR)
Minimum retrigger time
Minimum retrigger time
Symbol
tw(L),tw(H)
tw(L)
trr
trr
Test Condition
RX = 1 kΩ, CX = 100 pF
RX = 1 kΩ, CX = 0.01 µF
VCC (V)
2.0
4.5
6.0
2.0
4.5
6.0
2.0
4.5
6.0
2.0
4.5
6.0
Typ.
325
108
78
5.0
1.4
1.2
Limit
75
15
13
75
15
13
Unit
ns
ns
ns
µs
15.4.
15.4.
15.4.
15.4. Timing Requirements
Timing Requirements
Timing Requirements
Timing Requirements
(Unless otherwise specified, T
(Unless otherwise specified, T
(Unless otherwise specified, T
(Unless otherwise specified, Ta
a
a
a = -40 to 85
= -40 to 85
= -40 to 85
= -40 to 85
, Input: t
, Input: t
, Input: t
, Input: tr
r
r
r = t
= t
= t
= tf
f
f
f = 6 ns)
= 6 ns)
= 6 ns)
= 6 ns)
Characteristics
Minimum pulse width
Minimum pulse width
(CLR)
Symbol
tw(L),tw(H)
tw(L)
Test Condition
VCC (V)
2.0
4.5
6.0
2.0
4.5
6.0
Limit
95
19
16
95
19
16
Unit
ns
ns
2017-03-03
Rev.3.0
©2016 Toshiba Corporation
74HC123D
9
16.
16.
16.
16. AC Characteristics
AC Characteristics
AC Characteristics
AC Characteristics
(Unless otherwise specified, C
(Unless otherwise specified, C
(Unless otherwise specified, C
(Unless otherwise specified, CL
L
L
L = 15 pF, V
= 15 pF, V
= 15 pF, V
= 15 pF, VCC
CC
CC
CC = 5 V, T
= 5 V, T
= 5 V, T
= 5 V, Ta
a
a
a = 25
= 25
= 25
= 25
, Input: t
, Input: t
, Input: t
, Input: tr
r
r
r = t
= t
= t
= tf
f
f
f = 6 ns)
= 6 ns)
= 6 ns)
= 6 ns)
Characteristics
Output transition time
Propagation delay time
(A, B - Q, Q)
Propagation delay time
(CLR Trigger - Q, Q)
Propagation delay time
(CLR - Q, Q)
Symbol
tTLH,tTHL
tPLH,tPHL
tPLH,tPHL
tPLH,tPHL
Test Condition
Min
Typ.
4
25
26
16
Max
8
36
41
27
Unit
ns
16.1.
16.1.
16.1.
16.1. AC Characteristics (Unless otherwise specified, C
AC Characteristics (Unless otherwise specified, C
AC Characteristics (Unless otherwise specified, C
AC Characteristics (Unless otherwise specified, CL
L
L
L = 50 pF, T
= 50 pF, T
= 50 pF, T
= 50 pF, Ta
a
a
a = 25
= 25
= 25
= 25
, Input: t
, Input: t
, Input: t
, Input: tr
r
r
r = t
= t
= t
= tf
f
f
f
= 6 ns)
= 6 ns)
= 6 ns)
= 6 ns)
Characteristics
Output transition time
Propagation delay time
(A, B-Q, Q)
Propagation delay time
(CLR trigger-Q, Q)
Propagation delay time
(CLR-Q, Q)
Output pulse width
Output pulse width error between
circuits (in same package)
Input capacitance
Power dissipation capacitance
Symbol
tTLH,tTHL
tPLH,tPHL
tPLH,tPHL
tPLH,tPHL
twOUT
∆twOUT
CIN
CPD
Note
(Note 1)
Test Condition
CX = 28 pF
RX = 6 kΩ
CX = 28 pF
RX = 2 kΩ
CX = 0.01 µF,
RX = 10 kΩ
CX = 0.1 µF,
RX = 10 kΩ
VCC (V)
2.0
4.5
6.0
2.0
4.5
6.0
2.0
4.5
6.0
2.0
4.5
6.0
2.0
4.5
6.0
2.0
4.5
6.0
2.0
4.5
6.0
Min
90
95
95
0.9
0.9
0.9
Typ.
30
8
7
102
29
22
102
31
22
68
20
16
700
250
210
110
105
105
1.0
1.0
1.0
±1
5
162
Max
75
15
13
210
42
36
235
47
40
160
32
27
2000
400
340
130
115
115
1.2
1.1
1.1
Unit
ns
ns
ns
ns
ns
µs
ms
%
pF
pF
Note 1: CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current
consumption without load. Average operating current can be obtained by the equation.
ICC(opr) = CPD × VCC × fIN + ICC' × Duty/100 + ICC/2 (per circuit),
(ICC': Active supply current),
(Duty: %)
2017-03-03
Rev.3.0
©2016 Toshiba Corporation
74HC123D
10
16.2.
16.2.
16.2.
16.2. AC Characteristics (Unless otherwise specified, C
AC Characteristics (Unless otherwise specified, C
AC Characteristics (Unless otherwise specified, C
AC Characteristics (Unless otherwise specified, CL
L
L
L = 50 pF, T
= 50 pF, T
= 50 pF, T
= 50 pF, Ta
a
a
a = -40 to 85
= -40 to 85
= -40 to 85
= -40 to 85
,
,
,
,
Input: t
Input: t
Input: t
Input: tr
r
r
r = t
= t
= t
= tf
f
f
f = 6 ns)
= 6 ns)
= 6 ns)
= 6 ns)
Characteristics
Output transition time
Propagation delay time
(A, B-Q, Q)
Propagation delay time
(CLR trigger-Q, Q)
Propagation delay time
(CLR-Q, Q)
Output pulse width
Symbol
tTLH,tTHL
tPLH,tPHL
tPLH,tPHL
tPLH,tPHL
twOUT
Test Condition
CX = 28 pF, RX = 6 kΩ
CX = 28 pF, RX = 2 kΩ
CX = 0.01 µF, RX = 10 kΩ
CX = 0.1 µF, RX = 10 kΩ
VCC (V)
2.0
4.5
6.0
2.0
4.5
6.0
2.0
4.5
6.0
2.0
4.5
6.0
2.0
4.5
6.0
2.0
4.5
6.0
2.0
4.5
6.0
Min
90
95
95
0.9
0.9
0.9
Max
95
19
16
265
53
45
295
59
50
200
40
34
2500
500
425
130
115
115
1.2
1.1
1.1
Unit
ns
ns
ns
ns
ns
ns
ns
µs
µs
µs
ms
ms
ms
2017-03-03
Rev.3.0
©2016 Toshiba Corporation
74HC123D
11
17.
17.
17.
17. Characteristics Curves (Note)
Characteristics Curves (Note)
Characteristics Curves (Note)
Characteristics Curves (Note)
Fig.
Fig.
Fig.
Fig. 17.1
17.1
17.1
17.1 t
t
t
twOUT
wOUT
wOUT
wOUT - C
- C
- C
- CX
X
X
X (typ.)
(typ.)
(typ.)
(typ.) Fig.
Fig.
Fig.
Fig. 17.2
17.2
17.2
17.2 t
t
t
trr
rr
rr
rr - V
- V
- V
- VCC
CC
CC
CC (typ.)
(typ.)
(typ.)
(typ.)
Fig.
Fig.
Fig.
Fig. 17.3
17.3
17.3
17.3 Output Pulse Width Constant K - Supply
Output Pulse Width Constant K - Supply
Output Pulse Width Constant K - Supply
Output Pulse Width Constant K - Supply
Voltage (typ.)
Voltage (typ.)
Voltage (typ.)
Voltage (typ.)
Note: The above characteristics curves are presented for reference only and not guaranteed by production test,
unless otherwise noted.
2017-03-03
Rev.3.0
©2016 Toshiba Corporation
74HC123D
12
Package Dimensions
Package Dimensions
Package Dimensions
Package Dimensions
Unit: mm
Weight: 0.15 g (typ.)
Package Name(s)
Nickname: SOIC16
2017-03-03
Rev.3.0
©2016 Toshiba Corporation
74HC123D
13
RESTRICTIONS ON PRODUCT USE
RESTRICTIONS ON PRODUCT USE
RESTRICTIONS ON PRODUCT USE
RESTRICTIONS ON PRODUCT USE
• Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information
in this document, and related hardware, software and systems (collectively "Product") without notice.
• This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's
written permission, reproduction is permissible only if reproduction is without alteration/omission.
• Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible
for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which
minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage
to property, including data loss or corruption. Before customers use the Product, create designs including the Product, or incorporate
the Product into their own applications, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA
information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the
precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application
with which the Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications,
including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating
and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample
application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications.
TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS.
TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS.
TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS.
TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS.
• PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE
PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE
PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE
PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE
EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY
EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY
EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY
EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY
CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT
CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT
CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT
CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT
("UNINTENDED USE").
("UNINTENDED USE").
("UNINTENDED USE").
("UNINTENDED USE"). Except for specific applications as expressly stated in this document, Unintended Use includes, without limitation,
equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles,
trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices,
elevators and escalators, devices related to electric power, and equipment used in finance-related fields. IF YOU USE PRODUCT FOR
IF YOU USE PRODUCT FOR
IF YOU USE PRODUCT FOR
IF YOU USE PRODUCT FOR
UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT.
UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT.
UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT.
UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT. For details, please contact your TOSHIBA sales
representative.
• Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.
• Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any
applicable laws or regulations.
• The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any
infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any
intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.
• ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER,
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER,
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER,
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER,
INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING
INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING
INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING
INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING
WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND
WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND
WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND
WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND
(2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT,
(2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT,
(2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT,
(2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT,
OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
• Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation,
for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products
(mass destruction weapons). Product and related software and technology may be controlled under the applicable export laws and
regulations including, without limitation, the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration
Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all
applicable export laws and regulations.
• Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product.
Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances,
including without limitation, the EU RoHS Directive. TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING
TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING
TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING
TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING
AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS.
AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS.
AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS.
AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS.
2017-03-03
Rev.3.0
©2016 Toshiba Corporation
