S-860/870 Series Slotted Optical Switches Cr NOS A SENSORS AND CONTROLS GROUP 4 DOIMENSIONS ARE IN INCHES (MILLIMETERS) PIN FUNCTIONS CORRESPOND TO SYMBOLS SHOWN IN ~ D130 19.301 oy Tor yaw 0.120 13.08) aif 8 T aes i PACKAGE T PACKAGE N . " a | 9196 13.481 990 13.301 _| 0.240 ie a | Fr > ons 2.62) 120 13.081 OPTKAL G 3 ee - 9.080 12.08) Tv O 6.080 11.82) SO | a saz eae XS 0.300 17.621 . . bo. ~~ gue jog | PACKAGE L PACKAGE P 88 TYP. Features Absolute Maximum Ratings (T, = 25C unless otherwise stated. ) * aperture widths to 0.005(0.13mm) Storage and Operating Temperature .. * five electrical selections Lead Soldering Temperature............ two lead spaci . iRctransparent' or opaque housing IRED * four mounting options Continuous Forward Current Peak Forward Current (18 pulse width, 300pps) .. A Description Reverse Voltage ...... . The S-860/870 family of optical switches Power Dissipation... offers the designer the most flexible semi-cus- Sengor tom specification available in commercial optoelectronics. Electrical, optical, and Collector-Emitter Voltage mechanical parameters may be specified Emitter-Collector Voltage SY allowing the use of this standard product in POWET DisSipaAtiOn.....--eoeeecoreerr nee eerseereenrnesestnieteieneninantnasentannnserennectee set t00mWk many applications that would otherwise have Notes: to be custom-designed. Additional variety is found in the wired versions: S-880/890 series. See the S-960/970 and S-980/990 datasheets for similar devices with digital outputs or call OptoSwitch for applications assistance. 1. Housing is soluble in some common indusirial solvents; recommended cleaning agents are isopropanol or methanol. . 0.06" (1.5mm) from the case for 5 seconds maximum. 3. 260C maximum when wave soldering. 4. Derate linearty trom 25C at -1.33 mWPC. le ve. Ve Q 1 2 Vp- FORWARD VOLTAGE (V) Fundamental Characteristics Ip w Ta NORMALIZED |, va Ip NORMALIZED I a 8 Ip - DARK CURRENT (nA) - AMBIENT TEMP. (C) 5 0 6 OM BDH 4H - FORWARO CURRENT (mA) Ta OptoSwitch 1500 international Parkway, Suite 100 - Aichardeon, Texas 75081 + Phone: 214-479-1122 800-448-2900 CLAROSTAT Sensors and Controls 36S-860/870 Series Slotted Optical Switches Ores SENSORS AND CONTROLS GROUP Electrical Characteristics (T, = 25C unless otherwise stated) Symbol | Parameter | min | max | units | Test Conditions input Diode Ve Forward Voltage : 1.60 v Ip = 20mA In Reverse Current - 10 pA 1VR_ =3.0V Output Phototransistor'") Vieryceo | Collector-Emitter Breakdown Voltage 30 : Vv Ig = 1.0mA Visryeco | Emitter-Collector Breakdown Voltage 5.0 : le = 100pA Ib Dark Current - 100 nA |Vce = 10V, E, =0 Coupled) I Light Current Parameter A 0.5 : MA {ip = 20mA, Voge = 5V Parameter B 1.0 : mA {le = 10MA, Voge = 5V Parameter C 2.0 - mA |i = 20MA, Vog = 0.4V Parameter D 4.0 : mA |Ip = 20MA, Voce = 5V Parameter E 0.2 : MA Ip = 20MA, Voge = 5V Vce(sat) |Collector-Emitter Saturation Voltage Parameter A - 0.4 Vv Ie = 20mA, Io = 0.4MA Parameter B : 0.4 Vv Ip = 10MA, Io = 0.8MA Parameter C - 0.4 v Ig = 20mA, Ig = 2.0mA Parameter D : 0.4 Vv Ip = 20mA, Ic = 2.0MA Parameter E - 0.4 v Ip = 20mA, Io = 0.26MA Notes: 1. Radiation outside the sensitivity range of the device may be present during these measurements. Sufficient protection has been provided when the parameter being measured cannot be altered by further irradiation shielding. Other ranges of light current can be specified; call OptoSwitch for applications assistance. Some combinations of apertures are not available with IR-transmissive housings and certain electrical specifications. See the combination table on page 39 for specific information on availability of devices in this family and the S-880/890 families. Specifically, apertures narrower than 0.010" (0.25mm) are not available in |R-transmissive plastics and the higher current-transfer-ratios (parameters B, C, and D) are not available with smaller apertures. Part Number Guide OptoSwitch Optical Switch _ 8 7 a certure Widths and Allowed Combinations: ) Phototransistor Output Zz [RED Sensor 55 0.050(1.27mm 0.050(1.27mm Pye iRraneparent material 51 0.050(1.27mm, 0.010(0.25mm 7 = |R-opaque 0.050" 1.27mm 0.005"(0.13mm Electrical Selection with: 0.010" 0.25mm 0.010" 0.25mm Lead Spacing = 0.320(8.13mm) Lead Spacing = 0.220"(5.69mm) ooosto comm 0.008710. 3em 0 = Electrical Parameter A 5 = Electrical Parameter A . . . . 1 = Electrical Parameter B 6 = Electrical Parameter B Mounting Configuration: ; 2 = Electrical Parameter C 7 = Electrical Parameter C L = one mounting tab, iRED side 3 = Electrical Parameter D 8 = Electrical Parameter O N = no mounting tabs 4 = Electrical Parameter E 9 = Electrical Parameter E T = two mounting tabs . P = one mounting tab, sensor side OptoSwitch * 1500 International Parkway, Suite 100 Richardson, Texas 75081 Phone: 214-479-1122 800-448-2900 CLAROSTAT Sensors and Controls 37